TY - CONF A1 - Schaupp, Thomas A1 - Burger, S. A1 - Kannengießer, Thomas A1 - Zinke, M. A1 - Jüttner, S. T1 - Berichterstattung zum laufenden Projekt: „Ermittlung geeigneter Wärmeführungen zur Wasserstoffreduktion beim Schweißen höherfester Feinkornbaustähle mit modifiziertem Sprühlichtbogen“ N2 - Dieses Dokument fasst den Projekfortschritt des BAM-Projektes "Ermittlung geeigneter Wärmeführungen zur Wasserstoffreduktion beim Schweißen höherfester Feinkornbaustähle mit modifiziertem Sprühlichtbogen" im Rahmen des Fachausschusses 1 "Schweißmetallurgie & Werkstoffverhalten" des DVS e. V. zusammen. T2 - Sitzung des Fachausschusses 01 "Schweißmetallurgie & Werkstoffverhalten" der Forschungsvereinigung Schweißen und verwandte Verfahren des DVS e. V. CY - Düsseldorf, Germany DA - 17.03.2016 KW - Hochfester Feinkornbaustahl KW - Wasserstoff KW - MAG-Schweißen PY - 2016 AN - OPUS4-53670 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schaupp, Thomas A1 - Burger, S. A1 - Kannengießer, Thomas A1 - Zinke, M. A1 - Jüttner, S. T1 - Berichterstattung zum laufenden Projekt: „Ermittlung geeigneter Wärmeführungen zur Wasserstoffreduktion beim Schweißen höherfester Feinkornbaustähle mit modifiziertem Sprühlichtbogen“ N2 - Dieses Dokument fasst den Projekfortschritt des BAM-Projektes "Ermittlung geeigneter Wärmeführungen zur Wasserstoffreduktion beim Schweißen höherfester Feinkornbaustähle mit modifiziertem Sprühlichtbogen" im Rahmen des Fachausschusses 1 "Schweißmetallurgie & Werkstoffverhalten" des DVS e. V. zusammen. T2 - Sitzung des Fachausschusses 01 "Schweißmetallurgie & Werkstoffverhalten" der Forschungsvereinigung Schweißen und verwandte Verfahren des DVS e. V. CY - Düsseldorf, Germany DA - 08.09.2016 KW - Hochfester Feinkornbaustahl KW - Wasserstoff KW - MAG-Schweißen PY - 2016 AN - OPUS4-53671 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Bertovic, Marija T1 - Human Factors in Non-Destructive Testing (NDT): Risks and Challenges of Mechanised NDT T1 - Human Factors bei der zerstörungsfreien Prüfung (ZfP): Risiken und Herausforderungen mechanisierter ZfP N2 - Non-destructive testing (NDT) is regarded as one of the key elements in ensuring quality of engineering systems and their safe use. A failure of NDT to detect critical defects in safetyrelevant components, such as those in the nuclear industry, may lead to catastrophic consequences for the environment and the people. Therefore, ensuring that NDT methods are capable of detecting all critical defects, i.e. that they are reliable, is of utmost importance. Reliability of NDT is affected by human factors, which have thus far received the least amount of attention in the reliability assessments. With increased use of automation, in terms of mechanised testing (automation-assisted inspection and the corresponding evaluation of data), higher reliability standards are believed to have been achieved. However, human inspectors, and thus human factors, still play an important role throughout this process, and the risks involved in this application are unknown. The overall aim of the work presented in this dissertation was to explore for the first time the risks associated with mechanised NDT and find ways of mitigating their effects on the inspection performance. Hence, the objectives were to (1) identify and analyse potential risks in mechanised NDT, (2) devise measures against them, (3) critically address the preventive measures with respect to new potential risks, and (4) suggest ways for the implementation of the preventive measures. To address the first two objectives a risk assessment in form of a Failure Modes and Effects Analysis (FMEA) was conducted (Study 1). This analysis revealed potential for failure during both the acquisition and evaluation of NDT data that could be assigned to human, technology, and organisation. Since the existing preventive measures are insufficient to defend the system from identified failures, new preventive measures were suggested. The conclusion of the study was that those preventive measures need to be carefully considered with respect to new potential risks, before they can be implemented, thus serving as a starting point for further empirical studies. To address the final two objectives, two preventive measures, i.e. human redundancy and the use of automated aids in the evaluation of NDT data, were critically assessed with regard to potential downfalls arising from the social interaction between redundant individuals and the belief in the high reliability of automated aids. The second study was concerned with the potential withdrawal of effort in sequential redundant teams when working collectively as opposed to working alone, when independence between the two redundant individuals is not present. The results revealed that the first redundant inspector, led to believe someone else will conduct the same task afterwards, invested the same amount of effort as when working alone. The redundant checker was not affected by the information about the superior experience of his predecessor and—instead of expected withdrawal of effort—exhibited better performance in the task. Both results were in contradiction to the hypotheses, the explanations for which can be found in the social loafing and social compensation effects and in the methodological limitations. The third study examined inappropriate use of the aid measured in terms of (a) agreement with the errors of the aid in connection to the frequency of verifying its results and in terms of (b) the overall performance in the task. The results showed that the information about the high reliability of the aid did not affect the perception of that aid’s performance and, hence, no differences in the actual use of the aid were to be expected. However, the participants did not use the aid appropriately: They misused it, i.e. agreed with the errors committed by the aid and disused it, i.e. disagreed with the correct information provided by the aid, thereby reducing the overall reliability of the aid in terms of sizing ability. Whereas aid’s misuse could be assigned to low propensity to take risks and reduced verification behaviour because of a bias towards automation, the disuse was assigned to the possible misunderstanding of the task. The results of these studies raised the awareness that methods used to increase reliability and safety, such as automation and human redundancy, can backfire if their implementation is not carefully considered with respect to new potential risks arising from the interaction between individuals and complex systems. In an attempt to minimise this risk, suggestions for their implementation in the NDT practice were provided. N2 - Die zerstörungsfreie Prüfung (ZfP) wird als eines der wichtigsten Qualitätssicherungsmaßnahmen für technische Systeme und deren sichere Anwendung betrachtet. Wenn die ZfP kritische Defekte in sicherheitsrelevanten Anlagen, wie z.B. in der Kerntechnik, nicht entdeckt, kann dies zu katastrophalen Folgen für die Umwelt und den Menschen führen. Deshalb muss gewährleistet sein, dass die Verfahren der ZfP zuverlässig sind, d.h. dass sie alle kritischen Defekte entdecken können. Die Zuverlässigkeit der ZfP wird von menschlichen Faktoren beeinflusst, die jedoch bisher in diesem Feld selten betrachtet wurden. Durch den verstärkten Einsatz von Automatisierung beispielsweise bei der mechanisierten Prüfung (automatisierungsunterstütze Prüfung und die zugehörige Datenbewertung) wurde die Erreichung eines höheren Zuverlässigkeitsniveaus erwartet. Menschliche Faktoren sind trotz der Automatisierung immer noch bedeutsam für den gesamten Prüfprozess. Die Risiken der stärkeren Automatisierung der Prüfungen sind nicht vollständig bekannt. Das generelle Anliegen dieser Arbeit ist die erstmalige Feststellung der Risiken der mechanisierten ZfP und das Aufzeigen von Möglichkeiten, diese zu verringern. Die konkreten Ziele dieser Arbeit sind dementsprechend (1) die potenziellen Risiken bei der mechanisierten Prüfung aufzuzeigen und zu analysieren, (2) präventive Maßnahmen für diese Risiken abzuleiten, (3) diese präventiven Maßnahmen kritisch hinsichtlich neuer Risiken zu beleuchten sowie (4) Umsetzungsvorschläge aufzuzeigen. Für die ersten zwei Ziele wurde eine Risikoabschätzung mit der Fehlzustandsart- und auswirkungsanalyse (FMEA) durchgeführt (Studie 1). Diese Analyse ergab Fehlermöglichkeiten während der Datenaufnahme und –bewertung bei der mechanisierten ZfP, die dem Menschen, der Technik und der Organisation zugeordnet werden können. Weil die vorhandenen präventiven Maßnahmen unzureichend für die Vermeidung der identifizierten Fehler waren, wurden neue präventive Maßnahmen vorgeschlagen. Die Schlussfolgerung der Studie zeigt, dass vor der Umsetzung präventiver Maßnahmen eine sorgfältige Betrachtung hinsichtlich neuer potenzieller Risiken erfolgen muss. Dies war der Ausgangspunkt für die weiteren empirischen Untersuchungen. Für die letzten beiden Ziele wurden zwei präventive Maßnahmen untersucht: die menschliche Redundanz und die Anwendung automatisierter Assistenzsysteme bei der ZfP-Datenbewertung. Im Fokus lagen potenzielle Schwachstellen, die aus sozialer Interaktion der redundanten Individuen und aus dem Vertrauen in die hohe Zuverlässigkeit der automatisierten Assistenzsysteme entstehen können. In der zweiten Studie wurde die potenzielle Reduzierung der Anstrengung in sequentiellen redundanten Teams untersucht, indem die gemeinsame Aufgabenbearbeitung in Teams der individuellen Aufgabenbearbeitung gegenüber gestellt wurde. Die Ergebnisse zeigten, dass der erste redundante Prüfer, dem mitgeteilt wurde, dass ein anderer Prüfer die Prüfaufgabe nach ihm durchführen wird, die gleiche Anstrengung investierte wie der individuelle Bearbeiter. Der zweite redundante Prüfer (redundant checker) wurde durch die Information, dass sein Vorprüfer die höherwertige Erfahrung besitzt, nicht hypothesenkonform beeinflusst - anstelle der erwarteten Rücknahme der Anstrengung - zeigte er eine bessere Leistung bei der Durchführung der Aufgabe. Beide Ergebnisse stehen in Widerspruch zu den Hypothesen und können durch social loafing und social compensation Effekte sowie durch methodische Aspekte erklärt werden. In der dritten Studie wurde die unangemessene Nutzung eines automatisierten Assistenzsystems untersucht operationalisiert als (a) die Übereinstimmung mit Fehlern des Systems verbunden mit der Überprüfungshäufigkeit seiner Ergebnisse und (b) die Leistung bei der Aufgabe. Die Ergebnisse zeigten, dass die Information über die hohe Zuverlässigkeit des Systems die Wahrnehmung der Systemleistung nicht beeinflusste und folglich keine Unterschiede in der tatsächlichen Nutzung des Systems zu finden waren. Die Probanden nutzten jedoch das System nicht angemessen: sie stimmten den Fehlern des Systems zu (automation misuse) und sie lehnten korrekte Informationen des Systems ab (automation disuse). So reduzierten sie die Gesamtzuverlässigkeit des Systems, zumeist bei der Fehlergrößenbestimmung. Während misuse mit einer niedrigen Risikobereitschaft und eingeschränkten Überprüfungsverhalten auf Grund des automation bias erklärt werden kann, wird disuse dem möglichen Missverstehen der Aufgabe zugeordnet. Die Ergebnisse dieser Studien haben das Bewusstsein dafür erhöht, dass Methoden zur Erhöhung der Zuverlässigkeit und Sicherheit sowie Automatisierung und menschliche Redundanz versagen können, wenn die potenziellen Risiken ihrer Umsetzung aufgrund der Interaktion zwischen Mensch und Technik nicht bedacht werden. Um diese Risiken bei der Anwendung präventiver Maßnahmen zu minimieren, wurden Vorschläge für die ZfP-Praxis erarbeitet. T3 - BAM Dissertationsreihe - 145 KW - Failure modes and effects analysis KW - Zuverlässigkeit KW - Menschliche Faktoren KW - Zerstörungsfreie Prüfung KW - Fehlzustandsart- und auswirkungsanalyse KW - Personelle Redundanz KW - Human factors KW - Non-destructive testing KW - Human redundancy KW - Automation bias KW - Reliability PY - 2016 UR - https://nbn-resolving.org/urn:nbn:de:kobv:83-opus4-71292 SN - 978-3-9817502-7-0 DO - https://doi.org/10.14279/depositonce-4685 SN - 1613-4249 VL - 145 SP - 1 EP - 161 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-36090 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jaunich, Matthias A1 - Wolff, Dietmar T1 - Use of rubber seals at low temperatures N2 - Rubber is widely used as sealing material in various applications. In many fields the function of seal materials at low temperatures is necessary. Therefore, the understanding of failure mechanisms that lead to leakage at low temperatures is of high importance. It is known that the material properties of rubbers are strongly temperature dependent. At low temperatures this is caused by the rubber-glass transition (abbr. glass transition). During continuous cooling, due to the glass transition the material changes from rubber-like entropy-elastic behaviour to stiff energy-elastic behaviour, that allows nearly no strain or retraction. Hence, rubbers are normally used above their glass transition. But as the minimum working temperature limit of elastomers cannot be defined globally and precisely, the lower operation temperature limit of rubber seals should be determined in dependence of the application conditions and the most relevant material properties. In this paper, wesummarize results of our temperature dependent investigation of seal material properties by classical thermal analysis as Differential Scanning Calorimetry (DSC) and Dynamic Mechanical Analysis (DMA), combined with measurements of standardized tests as compression set and the seal performance determined in component tests. To reduce the test time of compression set tests a faster technique was developed and applied. To study the influence of dynamic events on the seal performance and to enhance the understanding of occurring seal failure, a setup for a fast partial seal release was designed. T2 - RubberCon 2016 CY - Tampere, Finland DA - 08.06.2016 KW - O-Ring KW - Compression set KW - Leakage rate KW - Low temperature PY - 2016 AN - OPUS4-36514 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rhode, Michael A1 - Steppan, Enrico A1 - Kannengießer, Thomas A1 - Steger, Jörg ED - Lippold, J. T1 - Effect of hydrogen on mechanical properties of heat affected zone of a reactor pressure vessel steel grade JF - Welding in the World N2 - The steel grade 20MnMoNi5-5 (according to German DIN standard or 16MND5 according to French AFNOR standard) is widely applied in (weld) fabrication of reactor pressure vessel components. Thus, a wide range of welding technologies (like submerged arc welding (SAW) or tungsten inert gas (TIG)) is used resulting in different heat affected zone (HAZ) microstructures. During weld fabrication, the weld joints may take up hydrogen. Especially, the HAZ shows an increased susceptibility for a degradation of the mechanical properties in presence of hydrogen. In addition, the hydrogen-assisted degradation of mechanical properties is influenced by three main local factors: hydrogen concentration, microstructure, and load condition. Hence, the base material (BM) and two different simulated non-tempered as-quenched HAZ microstructures were examined using hydrogen-free and hydrogen-charged tensile specimens. The results indicate that the effect of hydrogen on the degradation is significantly increased in case of the HAZ compared to the BM. In addition, hydrogen has remarkable effect in terms of reduction of ductility. It was ascertained that the degradation of the mechanical properties increases in the order of BM, bainitic HAZ, and the martensitic HAZ. Scanning electron microscope (SEM) investigation showed a distinct change of the fracture topography depended on the microstructure with increasing hydrogen concentration in case of the as-quenched HAZ microstructures. KW - Mechanical properties KW - Pressure vessel steels KW - Heat affected zone KW - Hydrogen KW - Hydrogen embrittlement KW - Low alloy steels PY - 2016 UR - http://link.springer.com/article/10.1007/s40194-016-0325-9 DO - https://doi.org/10.1007/s40194-016-0325-9 VL - 60 IS - 4 SP - 623 EP - 638 PB - Springer-Verlag GmbH CY - Heidelberg, Germany AN - OPUS4-36454 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mangelsdorf, Axel A1 - Blind, K. T1 - Motives to standardize: Empirical evidence from Germany JF - Technovation N2 - In this paper, we identify the strategic motives of German manufacturing companies in the electrical engineering and machinery industry to be involved in standards development organizations. First, we present the general motives for the formation of strategic alliances and relate them to specific standardization motives. Then, we identify pursuing specific company interests, solving technical problems, knowledge seeking, influencing regulation, and facilitating market access as motives to standardize by means of factor analysis. In a second step, we test hypotheses on the relationship between the importance of strategic motives and firm level variables, e.g. R&D intensity, innovation activities, and firm size. The results reveal that firms in electric engineering and machinery have a particularly strong interest in ensuring industry-friendly design of regulations, which can be achieved by standards. Moreover, the results confirm that small firms also from these two sectors are active in standardization alliances to access knowledge from other involved stakeholders. KW - Factor analysis KW - Standardization KW - Strategic alliances KW - Knowledge spillovers KW - Market access KW - Regulation KW - Innovation KW - R&D PY - 2016 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-364586 DO - https://doi.org/10.1016/j.technovation.2016.01.001 SN - 0166-4972 VL - 48-49 SP - 13 EP - 24 PB - Elsevier Science B.V. CY - Amsterdam, Netherlands AN - OPUS4-36458 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Marzok, Ulrich A1 - Müller, Ralf A1 - Reinsch, Stefan A1 - Gaber, Martin A1 - Welter, T. A1 - Deubener, J. T1 - Bestimmung der H2-Permeabilität von Gläsern mit der VHE-Methode N2 - Die Entwicklung von Wasserstoffbarrieren aus Glas erfordert die genaue Messung geringster H2-Permeabililtäten. Bisherige Untersuchungen haben gezeigt, dass die VHE-Pulvermethode diesbezüglich eine besonders hohe Empfindlichkeit bietet. Hierbei wird die isotherme Gasabgabe aus sphärischen Partikeln im Rahmen klassischer Diffusionsmodelle gefittet und daraus der Diffusionskoeffizient bestimmt. Für die Untersuchung von Gläsern mit möglichst geringer H2-Permeabilität ist jedoch eine Validierung der Genauigkeit der Methode notwendig. Vor diesem Hintergrund erfolgte die numerische Modellierung der H2-Abgabe mit Hilfe des Programms COMSOL Multiphysics®. Im Poster wird der Einfluss der Korngrößenverteilung der Glaspulverpartikel, der Partikelform sowie der Effekt einer nichthomogenen H2-Startverteilung auf die mittels Pulvermethode ermittelten Diffusionskoeffizienten diskutiert. T2 - 90. Glastechnische Tagung (Deutsche Glastechnische Gesellschaft e.V.) CY - Goslar, Germany DA - 06.06.2016 KW - Wasserstoffpermeation KW - Glas KW - Vakuumheißextraktion KW - Pulvermethode KW - Simulation PY - 2016 AN - OPUS4-36528 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sproesser, Gunther A1 - Pittner, Andreas A1 - Rethmeier, Michael A1 - Chang, Y.-J. A1 - Finkbeiner, M. T1 - Energy efficiency and environmental impacts of high power gas metal arc welding N2 - Single wire Gas Metal Arc Welding (SGMAW) and high power Tandem GMAW (TGMAW) are evaluated with respect to energy efficiency. The key performance indicator Electrical Deposition Efficiency is applied to reflect the energy efficiency of GMAW in different material transfer modes. Additionally, the wall-plug efficiency of the equipment is determined in order to identify the overall energy consumption. The results show that energy efficiency as well as economic process performance can be significantly increased by application of tandem processes. A comparative Life Cycle Assessment of a 30 mm thick weld is conducted to investigate the influences of the energy efficiency on the environmental impacts. Environmental burdens in the categories Global Warming Potential, Acidification Potential, Eutrophication Potential and Photochemical Ozone Creation Potential can be reduced up to 11% using an energy efficient TGMAW process T2 - IIW Intermediate Meeting Commission I, IV, XII / SG 212 CY - Genova, Italy DA - 07.03.2016 KW - Life cycle assessment (LCA) KW - Energy efficiency KW - High power welding KW - Tandem gas metal arc welding PY - 2016 AN - OPUS4-36535 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Geißler, Daniel A1 - Hildebrandt, N. T1 - Recent developments in Förster resonance energy transfer (FRET) diagnostics using quantum dots JF - Analytical and Bioanalytical Chemistry N2 - The exceptional photophysical properties and the nanometric dimensions of colloidal semiconductor quantum dots (QD) have strongly attracted the bioanalytical community over the last approximately 20 y. In particular, the integration of QDs in the analysis of biological components and interactions, and the related diagnostics using Förster resonance energy transfer (FRET), have allowed researchers to significantly improve and diversify fluorescence-based biosensing. In this TRENDS article, we review some recent developments in QD-FRET biosensing that have implemented this technology in electronic consumer products, multiplexed analysis, and detection without light excitation for diagnostic applications. In selected examples of smartphone-based imaging, single- and multistep FRET, steady-state and time-resolved spectroscopy, and bio/chemiluminescence detection of QDs used as both FRET donors and acceptors, we highlight the advantages of QD-based FRET biosensing for multiplexed and sensitive diagnostics. KW - Fluorescence spectroscopy and imaging KW - Multiplexing immunoassay KW - Nanoparticle KW - DNA/RNA KW - BRET/CRET PY - 2016 DO - https://doi.org/10.1007/s00216-016-9434-y SN - 1618-2642 SN - 1618-2650 VL - 408 IS - 17 SP - 4475 EP - 4483 PB - Springer-Verlag CY - Berlin, Heidelberg AN - OPUS4-36546 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grunewald, Thomas A1 - Grätz, Rainer A1 - Holländer, L. T1 - Ist Edelstahl wirklich funkenärmer als unlegierter Stahl? N2 - Experimentelle Untersuchungen zu streifenden Schlägen mit verschiedenen Edelstahlsorten in explosionsfähigen Atmosphären, jeweils bestehend aus Wasserstoff, Acetylen, Ethylen bzw. Propan mit Luft, haben gezeigt, dass deren Zündwahrscheinlichkeit sowohl von der Art des Brenngas-Gemisches als auch der Höhe der kinetischen Schlagenergie abhängt. Ein Einfluss des Chromgehaltes im Edelstahl auf die Zündwahrscheinlichkeit durch mechanisch erzeugte Schlagvorgänge konnte in dem untersuchten Bereich des Chromgehaltes nicht nachgewiesen werden, obwohl ein steigender Chromgehalt die Oxidationsfähigkeit abgetrennter Partikel erhöhter Temperatur tatsächlich senkt. Ferner haben weitere Werkstoffeigenschaften wie die Wärmeleitfähigkeit, spezifische Wärmekapazität, Dichte und Härte einen Einfluss auf die Zündwahrscheinlichkeit mechanischer Edelstahl-Schlagvorgänge bei Wasserstoff/Luft-Gemischen. Mit steigender Wärmeleitfähigkeit des Edelstahls sinkt die Zündwahrscheinlichkeit. Für die spezifische Wärmekapazität, Dichte und Härte konnte kein Einfluss nachgewiesen werden. Für Schlagvorgänge wurden in der Norm EN 13463-1:2009 (DIN, 2009) Grenzwerte für die maximale kinetische Schlagenergie festgelegt, unterhalb derer die Entstehung einer wirksamen Zündquelle als unwahrscheinlich angenommen werden kann. Dabei wurde zwischen Schlagvorgängen mit funkenarmen Metallen, wie z. B. Kupfer, Messing, und Schlagvorgängen mit sogenannten „sonstigen Werkstoffen“ unterschieden. Die Grenzwerte dieser sonstigen Werkstoffe resultieren aus Versuchen der BAM mit unlegiertem Baustahl. Bei solchen Schlagvorgängen wird von Oxidationsprozessen einzelner Partikel mit dem Luftsauerstoff ausgegangen, die das Gasgemisch aufgrund des hohen Temperaturanstiegs entzünden. In industriellen Anwendungen wie zum Beispiel der chemischen Industrie wird jedoch statt ferritischem Stahl überwiegend Edelstahl verwendet. Im Allgemeinen gilt mit Chrom hochlegierter Edelstahl bei Schlagvorgängen gegenüber ferritischem Stahl als funkenärmer, da die Oxidationsfähigkeit von Edelstahlpartikeln mit steigendem Chromgehalt abnimmt. Bei den Schlagversuchen der BAM konnte zwar eine sinkende Oxidationsfähigkeit der Partikel, aber keine abnehmende Zündwirksamkeit von Edelstählen mit steigendem Chromgehalt beobachtet werden. T2 - 14. BAM-PTB-Kolloquium zur chemischen und physikalischen Sicherheitstechnik CY - BAM, Berlin, Germany DA - 14.06.2016 KW - Mechanisch erzeugte Funken KW - Nichtelektrischer Explosionsschutz KW - Schlagfunken KW - Funken PY - 2016 AN - OPUS4-36548 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cabeza, Sandra A1 - Bruno, Giovanni A1 - Mishurova, Tatiana T1 - Characterization of multiphase metal matrix composites by means of CT and neutron diffraction N2 - The present study examines the relationship between the microstructure of multiphase metal matrix composites and their damage mechanisms. The matrix AlSi12CuMgNi was combined with 15% vol. Al₂O₃ (short fibers), and with 7% vol. Al₂O₃ + 15% vol. SiC (short fibers and whiskers, respectively). The experimental approach encompasses 3D microstructure characterization by means of computed tomography of samples (a) as-cast, (b) after heat treatment, and (c) after compression tests at room temperature. The volume fraction of different phases, their distribution, their orientation, and the presence of defects and damage are studied. The influence of the addition of SiC particles on mechanical properties of composite was investigated. Phase-specific load partition analysis for samples with fiber plane parallel to load was performed by using neutron diffraction (ND) during in-situ compression. ND results show damage in the Si phase, while Al₂O₃ short fibers carry load without damage until failure. The computed tomography observations confirm the load partition analysis. T2 - WCNDT CY - München, Germany DA - 13.06.2016 KW - thermal treatment KW - synchrotron CT KW - neutron diffraction KW - composite KW - aluminum KW - residual stress PY - 2016 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-365499 AN - OPUS4-36549 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gook, S. A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael A1 - El-Batahgy, A.M. T1 - Laser and hybrid laser-arc welding of cryogenic 9 % NI Steel JF - Global Nuclear Safety N2 - Heat treated 9%Ni steel is considered the most suitable and economic material for construction of large-size liquefied natural gas (LNG) storage tanks which operate at cryogenic temperatures (-196°C). Strength above 700 MPa as well as a minimum impact value of 60 J are required to ensure reliable operation of the LNG tanks at operating temperature. Conventional arc welding processes, including shielded metal arc welding, gas metal arc welding, gas tungsten arc welding and submerged arc welding, are currently used in construction of LNG tanks. Ni based filler wire is the preferred filler metal of choice in LNG tank construction. The main problem with this choice is the lower mechanical properties, particularly tensile strength of the weld metal. To compensate, the wall thickness needs to be excessively thick to ensure the strength of the welded structures. Ni based filler material is expensive and a large quantity is needed to fill the multi-pass weld grooves. These factors significantly add to the cost in the fabrication of LNG storage tanks. For these reasons, exploration of new welding technologies is a priority. A big potential can be seen in laser based welding techniques. Laser beam welding results in much smaller fusion zone with chemical composition and mechanical properties similar to that of the base material. Laser welding is a much faster process and allows for a joint geometry which requires less filler material and fewer welding passes. The advantages of laser welding can help to overcome the problems pointed out above. Trials of autogenous laser welding, laser cold-wire welding and hybrid laser-arc welding conducted on the 9%Ni steel are presented in this paper. Chemical composition of the weld metal as well as effects of welding parameters on the weld formation, microstructure and tensile strength is discussed. Filler wire penetration depth as well as character of its distribution in the narrow laser welds was examined using EPMA - electron probe microanalysis. KW - hardness KW - cryogenic steel KW - laser welding KW - microstructure KW - tensile strength PY - 2016 UR - http://gns.mephi.ru/sites/default/files/journal/file/en.2016.1-4.pdf SN - 2499-9733 VL - 1 IS - 18 SP - 34 EP - 45 PB - Research Nuclear University MEPHl CY - Moskau, Russia AN - OPUS4-36553 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Marzok, Ulrich A1 - Müller, Ralf A1 - Reetz, R. A1 - Trunkhardt, M. T1 - High-temperature laser profilometry N2 - Advanced methods for 3D green density characterization like computed tomography and 3D FE sinter modeling can be utilized for increasing the reliability of sintered components. The experimental in situ observation of sin-tering, however, is currently restricted to silhouette methods, i.e. heating microscopy. For complex shaped sam-ples, in situ shape screening during shrinkage would allow better validation of 3D sinter simulation models. Further, by revealing temporary sinter warpage, 3D high-temperature shape screening would allow to locate potential defects of complex sintered components. Against this background, BAM developed a testing device for in situ 3D high-temperature shape screening for ceramic and glass-ceramic tapes up to 1000°C [1-3]. Current work is focused on dropping this restriction in sample shape and temperature. The poster illustrates the current state of this work and possible applications of the method e.g. in detecting sinter warpage of metallized glass-ceramic LTCC tapes. T2 - 90. Glastechnische Tagung (Deutsche Glastechnische Gesellschaft e.V.) CY - Goslar, Germany DA - 06.06.2016 KW - Laser profilometry KW - 3D High-temperature shape screening KW - Sintering PY - 2016 AN - OPUS4-36510 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Resch-Genger, Ute A1 - Grabolle, Markus A1 - Starke, M. T1 - Highly fluorescent dye-nanoclay hybrid materials made from different dye classes JF - ACS Publications N2 - Nanoclays like laponites, which are commercially avaible in large quantities for a very moderate price, provide a facile solubilization strategy for hydrophobic dyes without the need for chemical functionalization and can act as a carrier for a high number of dye molecules. This does not require reactive dyes, amplifies fluorescence signals from individual emitters due to the high number of dyes molecules per laponite disk, and renders hydrophobic emitters applicable in aqueous environments. Aiming at the rational design of bright dye-loaded nanoclays as a new class of fluorescent reporters for bioanalysis and material sciences and the identification of dye structure−property relationships, we screened a series of commercial fluorescent dyes, differing in dye class, charge, and character of the optical transitions involved, and studied the changes of their optical properties caused by clay adsorption at different dye loading concentrations. Upon the basis of our dye loading density-dependent absorption and fluorescence measurements with S2105 and Lumogen F Yellow 083, we could identify two promising dye−nanoclay hybrid materials that reveal high fluorescence quantum yields of the nanoclay-adsorbed dyes of at least 0.20 and low dye self-quenching even at high dye-loading densities of up to 50 dye molecules per laponite platelet. KW - nanoclay KW - laponite KW - fluorescence KW - organic dye KW - carrier system KW - fluorescent reporter KW - screening PY - 2016 DO - https://doi.org/10.1021/acs.langmuir.5b04297 SN - 0743-7463 VL - 2016 IS - 32 SP - 3506 EP - 3513 PB - Amer Chemical SOC CY - Washington, DC, USA AN - OPUS4-36511 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Erwamati, F. U. A1 - Pratapa, S. A1 - Suasmoro, S. A1 - Hübert, Thomas A1 - Banach, Ulrich T1 - Preparation and structural study of Mg1−xZnxTiO3 ceramics and their dielectric properties from 1 Hz to 7.7 GHz JF - Journal of Materials Science: Materials in Electronics N2 - A series of Mg₁₋ₓZnₓTiO₃, x = 0–0.5 (MZT0–MZT0.5) ceramics was synthesised and characterised. The dielectric properties of the samples in the frequency range of 1 Hz – 7.7 GHz were explored using three different methods: a contacting electrode method, a parallel-plate method and a perturbed resonator method. The electrical properties in the space charge and dipolar polarisation frequency ranges are discussed in relation to the phase composition and microstructure data. Differences in the zinc Substitution divided the dielectrics into two groups, namely MZT0-MZT0.2 and MZT0.3–MZT0.5, each with different amount of a main Mg₁₋ₓZnₓTiO₃ solid solution phase and a secondary solid solution phase. Zinc substitution promoted the density of the ceramics, improved the purity of the main phase and increased the permittivity for frequencies up to 10⁸ Hz, but reduced the permittivity in the microwave range. In the MZT0.3–MZT0.5 samples, for frequencies less than 1 MHz the quality (Q x ƒ) factors were lower and log σ ₐ.c, the AC conductivity, was higher than for the MZT0–MZT0.2 samples. Above 10 MHz, the (Q x ƒ) factors and log σ ₐ.c of the two groups were similar. KW - Mg1-xZnxTiO3 KW - Space charge polarisation KW - Dipole polarisation KW - Microwave frequency KW - Dielectric properties PY - 2016 DO - https://doi.org/10.1007/s10854-016-4610-6 SN - 0957-4522 VL - 27 IS - 7 SP - 6637 EP - 6645 PB - Springer CY - Dordrecht, Netherlands AN - OPUS4-36466 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Woydt, Mathias A1 - Mohrbacher, H. T1 - Adjusting the functional properties of niobium carbide N2 - The process window and range of functional properties of NbC is wide, because micro-hardness, hot hardness, sliding wear resistance, elastic modulus and toughness can be tailored by the C/Nb ratio, because Nb4C3, Nb6C5 and other short and long range ordered phases occur in the region of homogeneity of NbCx (0,75≤ x ≤1.0) in the binary Phase diagram, and by the type of binder. Further improvements enable the addition of secondary carbides. Supporting results from literature and different grades with varying C/Nb ratio or binder types were illuminated. Thus, the NbC system offers to producers a wider process window, than WC. The impact of these tailored properties on sliding wear and cutting performance was illuminated by tribological and machining results. NbC can be synthesized by carbothermal conversion of Nb2O5 or be metallurgically grown in melts and leached out as coarse NbC cubes. NbC provides comparably lower friction in many relevant tribo-contacts and displays low wear. NbC and Nb2O5 have so far no REACH classification related to human toxicology and are not listed as substances of very high concern contrary to WO3 and Co3O4. T2 - 2016 International Conference on Powder Metallurgy & Particulate Materials CY - Boston, MA, USA DA - 05.06.2016 KW - Niobium carbide KW - NbC KW - Wear KW - Friction PY - 2016 AN - OPUS4-36497 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Madkour, Sherif A1 - Szymoniak, Paulina A1 - Schönhals, Andreas T1 - Evidence of a Three-Layred Structure in Ultrathin PVME and PVME-PS Blend Films by Nanosized Relaxation Spectroscopy N2 - In the course of miniaturizing modern technology down to the molecular scale, much remain unknown about the materials behavior and the deviations from the bulk that might arises from confinement effects. Here, a combination of nano-sized relaxation spectroscopies (Broadband dielectric spectroscopy (BDS) and Specific heat spectroscopy (SHS); employing AC nanochip calorimetry) were utilized to investigate the glassy dynamics of ultra-thin films of Poly (vinyl methyl ether) (PVME) and of blends PVME / Polystyrene (PS) 50:50 wt-%,, which are miscible in bulk (thicknesses: ca. 8 nm – 160 nm, film thickness was controlled by ellipsometry, film topography by AFM). Both methods are sensitive to different probes; where SHS senses entropy fluctuations while BDS measures dipole fluctuations. For BDS measurements, a recently developed nano-structured electrode sample arrangement is employed, where ultra-thin films are spin-coated on an ultra-flat highly conductive silicon wafer, sandwiched between a wafer with nanostructured SiO2 nano-spacers with heights between 35 nm and 70 nm. For PVME films, two thickness independent processes were observed and interpreted to be the α-processes of a bulk-like layer and a process due to an absorbed layer to the substrate. This adsorbed layer further undergoes a confinement effect that results in the localization of the segmental dynamics, which results in an Arrhenius-like temperature dependence. A detailed analysis of the dielectric strengths of both processes reveals that the thickness of the adsorbed layer decreases with increasing temperature, while that of the bulk-like layer increases. For the blend system, by measuring the dynamic Tg in dependence of the film thickness, SHS showed that the Tg of the whole film was strongly influenced by a nanometer-thick surface layer at the polymer/air interface due to a self-assembling process. The dynamic Tg obtained from the SHS measurements decreased with decreasing film thickness. On the other hand, BDS measurements showed a completely different behavior. At high temperatures, the temperature dependence of the relaxation times of the films follows that of bulk-like PS/PVME; obeying the VFT-law. With decreasing temperature, the temperature dependence deviates from the VFT to an Arrhenius law; where the apparent activation energy decreases with decreasing film thickness. This is the first example where confinement induced changes were observed by BDS for ultra-thin films. All results were analyzed in detail in a comprehensive discussion. T2 - 14. Lähnwitzseminar on Calorimetry CY - Rostock-Warnemünde, Germany DA - 05.05.2016 KW - Ultra-Thin films PY - 2016 AN - OPUS4-36477 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sentker, K. A1 - Yildirim, Arda A1 - Knopp, K. A1 - Schönhals, Andreas A1 - Huber, P. T1 - Columnar axial orientation of discotic liquid crystals in nanoporous solids N2 - Successful implementation of an optical polarimetry measurement setup. Due to wall anchoring interactions HAT6 embedded in an untreated alumina membrane exhibits a radial orientation for pore sizes in between 30 nm and 80 nm. Embedded in large membranes, pore size of 180 nm, HAT6 forms the favored hexagonal columnar phase along the pore axis. T2 - 80. Jahrestagung der DPG und DPG-Frühjahrstagung CY - Regensburg, Germany DA - 06.03.2016 KW - Discotic Liquid Crystals KW - Nanoconfinement KW - Orientation PY - 2016 AN - OPUS4-36479 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mann, Guido A1 - Krüger, Jörg ED - Jitsuno, T. ED - Shao, J. ED - Rudolph, W. T1 - Nanosecond laser damage of optical multimode fibers T2 - Proceedings of SPIE N2 - For pulse laser materials processing often optical step index and gradient index multimode fibers with core diameters ranging from 100 to 600 μm are used. The design of a high power fiber transmission system must take into account limitations resulting from both surface and volume damage effects. Especially, breakdown at the fiber end faces and self-focusing in the fiber volume critically influence the fiber performance. At least operation charts are desirable to select the appropriate fiber type for given laser parameters. In industry-relevant studies the influence of fiber core diameter and end face preparation on laser-induced (surface) damage thresholds (LIDT) was investigated for frequently used all-silica fiber types (manufacturer LEONI). Experiments on preform material (initial fiber material) and compact specimens (models of the cladding and coating material) accompanied the tests performed in accordance with the relevant LIDT standards ISO 21254-1 and ISO 21254 2 for 1-on-1 and S-on-1 irradiation conditions, respectively. The relation beam diameter vs. LIDT was investigated for fused silica fibers. Additionally, laser-induced (bulk) damage thresholds of fused silica preform material F300 (manufacturer Heraeus) in dependence on external mechanical stress simulating fiber bending were measured. All experiments were performed with 10-ns laser pulses at 1064 and 532 nm wavelength with a Gaussian beam profile. T2 - Pacific Rim Laser Damage 2016 CY - Yokohama, Japan DA - 18.05.2016 KW - laser damage KW - optical fiber KW - nanosecond laser KW - fused silica PY - 2016 DO - https://doi.org/10.1117/12.2238515 VL - 9983 SP - 99830T AN - OPUS4-37140 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weise, Frank A1 - Meng, Birgit A1 - Pirskawetz, Stephan A1 - Voland, K. T1 - Influence of simultaneous cyclic loading and external alkali supply on the alkali-silica reaction in concrete pavements T2 - 15th International Conference on Alkali-Aggregate reaction (ICAAR 2016) N2 - In recent years the German motorway network has seen an increase in the occurrence of damage to concrete road surfaces which can be attributed to the alkali-silica reaction (ASR). In view of the often drastically reduced life expectancy of road surfaces due to ASR, research activity in this field has notably increased. Alongside preventative measures in concrete technology, the main research focus up to now has been the development of performance-oriented testing procedures for ASR prevention. This included more specifically the accelerated simulation of climatic effects and external alkali penetration on road surfaces. The effects of mechanical pre-damage resulting from cyclic traffic loading and climatic impact had previously not been taken into consideration. Since 2011, the five-partner research group 1498 sponsored by the German Research Foundation (DFG) has been pursuing research on how simultaneous cyclic loading and external alkali penetration impacts destructive ASR in road surface concretes. The depiction of the myriad degradation and transport processes necessary for an understanding of these effects requires close interaction between experiments and their multi-scale modelling. This paper aims to focus on the aforementioned experiments by means of innovative testing techniques. The research is founded on a series of cyclic fatigue tests performed on large-format beams, both with and without previous application of a sodium chloride (NaCl) solution, with simultaneous tracking of crack development. Subsequently, smaller test specimens were extracted from the pre-damaged beams for further experiments. These included the spatial visualization and quantification of fatigue-induced cracks using micro X-ray 3D-computed tomography (3D-CT). Additionally, the effects of fatigue-induced cracks on alkali transport were investigated using Laser-Induced Breakdown Spectroscopy (LIBS). Subsequent storage of the small-format test specimens, with and without cyclic pre-damage, in an ASR-conducive environment then provided initial findings on the influence of fatigue-induced predamage on the ASR. T2 - 15th International Conference on Alkali-Aggregate reaction (ICAAR 2016) CY - Sao Paulo, Brazil DA - 03.07.2016 KW - concrete pavements KW - alkali-silica-reaction KW - fatigue KW - damage monitoring PY - 2016 SP - Paper 191 AN - OPUS4-37142 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Werner, Daniel A1 - Meng, Birgit A1 - Weise, Frank T1 - Influence of aggregate size on the damage potential of alkali-silica reaction T2 - 15th International Conference on Alkali-Aggregate Reaction (ICAAR 2016) N2 - The susceptibility of different aggregate types used in concrete to ASR is strongly associated with their petrography. The aim of this study is to assess the influence of the aggregate size on the ASR potential, in particular applied to the sand fractions in the size range of 0.125-4 mm. The investigation concept is based on the hypothesis that at a specific particle size reactive aggregates could change their characteristic influence in mitigating ASR instead of promoting it. For the study of the size dependent behaviour mortars are prepared, considering aggregates of different reactivity, including very reactive, slow-late and quasi non-reactive types. The analysis is based on a stepwise substitution concept, in which mortars with a constant overall grain size distribution are compared, while only one size fraction of the non-reactive base aggregate is substituted by a reactive aggregate type of this specific size fraction. For the expansion experiments an accelerated mortar bar test (80°C, immersed in NaOH solution) was applied. The results show that the slow-late reactive greywacke yielded a strong reduction of the expansion below an aggregate size in the range of 0.5-1 mm. On the other side with the very reactive borosilicate glass, the expansions increased steadily with decreasing size. To validate if the acquired expansions were caused by ASR, thin sections were analysed. Mainly, higher expansion values were consistent with extensively more amounts of ASR indicators. T2 - 15th International Conference on Alkali-Aggregate Reaction (ICAAR 2016) CY - Sao Paulo, Brazil DA - 03.07.2016 KW - alkali-silica-reaction KW - building materials KW - concrete KW - durability PY - 2016 SP - Paper 194 AN - OPUS4-37143 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Miccoli, Lorenzo A1 - Fontana, Patrick A1 - Ziegert, C. A1 - Müller, P. ED - Modena, C. ED - da Porto, F. ED - Valluzzi, M. R. T1 - Calibration of partial safety factors for earth block masonry under compression loading T2 - IB2MAC Brick and Block Masonry - Trends, Innovations and Challenges N2 - The goal of the present study is to assess the feasibility to develop a first reliable database of materials parameters for Earth Block Masonry (EBM). The database is crucial when defining the materials safety factors. In the first part an experimental campaign of compressive tests were carried out on two types of earth block and two types of earth mortar. The results showed that the mean variation of the compressive strength was remarkably less than expected. This low variation is related to a production with high quality standards of the materials employed. In the second part a partial safety factor for EBM under uniaxial compression was determined through the reliability method. The results proved the reliability of a common calculation method for EBM based on partial safety factors following the current standards. T2 - IB2MAC 2016 - 16th International Brick and Block Masonry Conference CY - Padua, Italy DA - 26.06.2016 KW - earth block masonry KW - partial safety factors KW - uniaxial compression test PY - 2016 SN - 978-1-138-02999-6 SP - 857 EP - 864 PB - CRC Press Taylor & Francis Group CY - London, UK AN - OPUS4-37145 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Woydt, Mathias A1 - Mohrbacher, H. A1 - Vleugels, J. A1 - Huang, S. T1 - Niobium carbide for wear protection - tailoring its properties by processing and stoichiometry JF - Metal Powder Report N2 - Niobium carbide is a hardly explored carbide but its functional profile shows a high potential for wear protection and tribological applications, which are currently dominated by tungsten carbide. Surprisingly little information is available on niobium carbide (NbC). Niobium carbide can be either synthesized by carbothermal conversion of Nb2O5 or be metallurgically grown and leached out. Furthermore, NbC hardmetal grades can be bonded by all known metallic binders and processed and sintered in exactly the same way as WC-based hardmetals. Niobium is today largely available. NbC can be efficiently produced, provides comparably low friction in many relevant tribo-contacts and displays low wear. NbC and Nb2O5 have so far no REACH classification related to human toxicology and are not listed as substances of very high concern contrary to WO3 and Co3O4. This contribution demonstrates the key characteristics of NbC and discusses its sustainability and reliable value chain. KW - niobium carbide KW - wear KW - machining PY - 2016 DO - https://doi.org/10.1016/j.mprp.2015.12.010 SN - 0026-0657 VL - 71 IS - 4 SP - 265 EP - 272 PB - Elsevier Ltd. AN - OPUS4-37150 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Falkenberg, Rainer T1 - Simulation of Environmentally-Assisted Material Degradation by a Thermodynamically Consistent Phase-Field Model JF - Key Engineering Materials N2 - Environmentally-assisted material degradation involves mass transport and mechanical processes interacting in the material. A well-known example is hydrogen-induced stress-corrosion cracking. One major challenge within this scope is the quantification of the coupling mechanisms in question. The computational modeling of environmentally-assisted cracks is the key objective of this investigation and realised within the theory of gradient-extended dissipative continua with lengthscales. The modeling of sharp crack discontinuities is replaced by a diffusive crack model based on the introduction of a crack phase-field to maintain the evolution of complex crack topologies. Within a thermodynamical framework allowing for mechanical and mass transport processes the crack phasefield is capable to model crack initiation and propagation by the finite element method. As complex crack situations such as crack initiation, curvilinear crack patterns and crack branching are usually hard to realise with sharp crack models, they can be assessed without the requirement of a predefined crack path within this method. The numerical modeling of a showcase demonstrates a crack initiation as well as a crack propagation situation with respect to the determination of stress-intensity factors; a crack deviation situation with a curvilinear crack path is modeled by the introduction of a geometrical perturbation and a locally enhanced species concentration. KW - Finite-element method KW - Crack growth KW - Crack initiation KW - Mass transport KW - Phase field model PY - 2016 DO - https://doi.org/10.4028/www.scientific.net/KEM.713.38 SN - 1662-9795 VL - 713 SP - 38 EP - 41 PB - Trans Tech Publications CY - Switzerland AN - OPUS4-37152 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hertwig, Andreas A1 - Rosu, Dana A1 - Ortel, Erik A1 - Kraehnert, R. A1 - Hodoroaba, Vasile-Dan T1 - Measurement of Porous TiO2 Layers with spectroscopic ellipsometry – a multi-method study N2 - By means of an effective medium (EMA) based approach, it is possible to use spectroscopic ellipsometry to determine the mixing ratios between air and material in porous dielectrics and calculate a quantitative value of the porosity for these materials. As this method is model-based, it is very difficult to provide a quantitative measure for the accuracy of porosity values determined by this method. Valuable additional information can often be obtained by combining ellipsometry with other complementary methods. In the present study, the ellipsometry results were validated by Electron Probe Microanalysis (EPMA) with the option of layer analysis (by the socalled “STRATAGem” approach), gravimetry, and electron microscopy. We analysed porous TiO2 thin layers synthesised by means of a template synthesis approach (evaporation induced self assembly). Ellipsometry measurements on porous samples are difficult to analyse due to the complexity of the models necessary. Often it is difficult to decide if the measured data contains enough information to successfully determine the target quantities (mixing ratio, dielectric function of the matrix material). One method to decrease the complexity of the fit and therefore use the measurement data most efficiently is a multi-sample analysis. In the present case, multi-sample analysis was used for determining the porosity factors of the individual layers while using one common set of dielectric function values for the matrix in all cases. While the results of the fit analysis in this case can be used to show the feasibility and also the limitations of the multi-method approach, the porosity values themselves show a promising agreement between the independent methods. It can therefore be concluded that determining porosity values with ellipsometry is in accordance to other methods to the level of accuracy provided by the complementary methodologies. T2 - International conference on spectroscopic ellipsometry (ICSE-7) CY - Berlin, Germany DA - 06.06.2016 KW - Spectroscopic Ellipsometry KW - Electron Microscopy KW - Multi-method Metrology KW - Porous Materials KW - Thin Films KW - Titanium Dioxide PY - 2016 AN - OPUS4-37202 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Naka, A. A1 - Yasutaka, T. A1 - Sakanakura, H. A1 - Kalbe, Ute A1 - Watanabe, Y. A1 - Inoba, S. A1 - Takeo, M. A1 - Inui, T. A1 - Katsumi, T. A1 - Fujikawa, T. A1 - Sato, K. A1 - Higashinog, K. A1 - Someyaga, M. T1 - Column percolation test for contaminated soils: Key factors for standardization JF - Journal of Hazardous Materials N2 - Column percolation tests may be suitable for prediction of chemical leaching from soil and soil materials. However, compared with batch leaching tests, they are time-consuming. It is therefore important to investigate ways to shorten the tests without affecting the quality of results. In this study, we evaluate the feasibility of decreasing testing time by increasing flow rate and decreasing equilibration time compared to the conditions specified in ISO/TS 21268-3, with equilibration periods of 48 h and flow rate of 12 mL/h. We tested three equilibration periods (0, 12–16, and 48 h) and two flow rates (12 and 36 mL/h)on four different soils and compared the inorganic constituent releases. For soils A and D, we observed similar values for all conditions except for the 0 h–36 mL/h case. For soil B, we observed no appreciable differences between the tested conditions, while for soil C there were no consistent trends probably due to the difference in ongoing oxidation reactions between soil samples. These results suggest that column percolation tests can be shortened from 20 to 30 days to 7–9 days by decreasing the equilibration time to 12–16 h and increasing the flow rate to 36 mL/h for inorganic substances. KW - Contaminated soils KW - Column percolation PY - 2016 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-372038 DO - https://doi.org/10.1016/j.jhazmat.2016.08.046 SN - 0304-3894 VL - 320 SP - 326 EP - 340 PB - Elsevier B.V. AN - OPUS4-37203 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ferraioli, M. A1 - Abruzzese, D. A1 - Miccoli, Lorenzo A1 - Mandara, A. ED - Galea, P. ED - Borg, R. P. ED - Farrugia, D. ED - Agius, M. R. ED - D'Amico, S. ED - Torpiano, A. ED - Bonello, M. T1 - Dynamic identification and seismic safety of two masonry towers T2 - Proceedings of the International Conference: Georisk in the Mediterrean and their mitigation N2 - The recent experience of Italian seismic events provided wide observational information about typical behaviour, damage patterns and intrinsic vulnerability of monumental buildings. Evidence indicates that historical constructions are by far the most vulnerable from the seismic point of view. As a consequence, they demand for the definition of urgent strategies for the protection of cultural heritage from seismic hazard. The main goal of an in-depth knowledge of the structure should help to avoid inadequate, unsuitable or dangerous rehabilitation operations, as well as to select non-invasive and reversible techniques for the best exploitation of material and technology features. The definition of reliable models and methods for seismic risk assessment of historical constructions is today a very important topic. Typical problems of masonry structures concern aspects like inherent structural lacks, material degradation, geotechnical problems, buckling behaviour of slender elements and dynamic loading vulnerability. Modelling the mechanical behaviour of masonry may play an important role, due to both inherent material complexity and great scatter in mechanical properties. Effective procedures for the identification of the structural parameters from static and dynamic testing are thus required. In particular, dynamic measurements may be very useful for the identification of mechanical properties and soil restraints and, consequently, for the calibration of advanced numerical finite element models. The paper addresses two case studies of structural monitoring and seismic assessment of medieval masonry towers in Italy: the bell tower of Aversa and the bell tower of Capua. These monuments, placed in the Campania region, were monitored by means of full-scale environmental vibration testing. Measured responses are then used for modal identification with a typical finite element model updating technique based on vibration test results. Parameters optimization is carried out on the basis of a criterion which minimises a weighted error on modal properties. A satisfactory improvement in the determination of modal parameters is thus obtained, resulting in a close agreement between the modal properties observed in dynamic tests and those calculated from numerical model. Seismic assessment is finally performed based on nonlinear static analysis of the tower under multimodal distributions of lateral loads. Results from nonlinear analysis indicate the potential collapse mechanisms and evidence dangerous structural weakness which may play a role in the seismic vulnerability of the towers. T2 - Georisk in the Mediterrean and their mitigation CY - Valletta, Malta DA - 20.07.2015 KW - masonry towers KW - ambient vibration tests KW - dynamic characterisation KW - seismic assessment PY - 2016 SN - 978-88-98161-20-1 SP - 250 EP - 251 PB - Mistral Service AN - OPUS4-37204 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Fontana, Patrick ED - Jäger, W. T1 - Teilsicherheitsbeiwerte auf Materialseite im Lehmmauerwerksbau - versuchsgestützte Kalibrierung für den Lastzustand Druck T2 - Mauerwerk Kalender 2016 - Baustoffe, Sanierung, Eurocode-Praxis N2 - Anhand von Versuchsergebnissen und zuverlässigkeitstheoretischen Grundlagen erfolgte die Ermittlung eines Teilsicherheitsbeiwertes für Lehmmauerwerk unter dem Lastzustand Druck nach der Kalibrationsmethode der DIN EN 1990. Darüber hinaus fanden Untersuchungen zur Ermittlung der Parameter zur Bestimmung der rechnerischen Mauerwerksfestigkeit statt. Aufgrund der derzeit noch ungenügenden Datengrundlage konnten lediglich erste Empfehlungen für Teilsicherheitsbeiwerte ausgesprochen werden. Ein Bemessungskonzept im Lehmmauerwerksbau auf Basis von Teilsicherheitsbeiwerten, welches sich an der gültigen Mauerwerksnormung anlehnt, scheint aber prinzipiell möglich. Es bedarf allerdings noch weiterer Forschung, insbesondere im Hinblick auf andere Lastzustände und auf das Feuchtigkeitsverhalten von Lehmmauerwerk. KW - Baustoffe KW - Zuverlässigkeitstheorie KW - Prüfung KW - Lehmsteinmauerwerk KW - Druckfestigkeit KW - Lehmsteine KW - Lehmmauermörtel PY - 2016 SN - 978-3-433-03131-5 SN - 0170-4958 VL - 41. Jahrgang, Kap. 2.2.13 SP - 560 EP - 561 PB - Wilhelm Ernst & Sohn, Verlag für Architektur und technische Wissenschaften GmbH & Co. KG CY - Berlin AN - OPUS4-37207 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Fontana, Patrick ED - Jäger, W. T1 - NIKER - New integrated knowledge based approaches to the protection of cultural heritage from earthquake-induced risk T2 - Mauerwerk Kalender 2016 - Baustoffe, Sanierung, Eurocode-Praxis N2 - Im Rahmen des abgeschlossenen EU-Projekts NIKER (www.niker.eu) wurden die mechanischen Eigenschaften von Lehmsteinmauerwerk untersucht. Im ersten Teil wurde das mechanische Verhalten unter statischer Druck- und Schubbeanspruchung bestimmt. Ziel dieser Untersuchungen war es, grundlegende Daten zum Verformungs- und Versagensverhalten von Lehmbauteilen zu erhalten und dieses mit einem numerischen Modell zu beschreiben. Die Versuchsergebnisse belegten das spröde Verhalten von Lehmmauerwerk bei uniaxialer Druckbelastung und zeigten, dass das Versagen von Lehmmauerwerk infolge Schubbelastung nach Erstrissbildung in Mörtelfugen und Lehmsteinen durch Gleiten der Lehmsteine entlang der Mörtelfugen erfolgt. Mit der Software DIANA® wurden numerische Modelle entwickelt. Eine Makromodellierung erbrachte zufriedenstellende Resultate hinsichtlich des Spannungs-Dehnungs-Verhaltens unter statischem Druck, während mit einer Mikromodellierung zufriedenstellende Ergebnisse hinsichtlich des Spannungs-Dehnungs-Verhaltens unter statischer Schubbeanspruchung erzielt wurden. Für beide Fälle, d.h. Makromodellierung von statischem Druck und Mikromodellierung von statischem Schub, wurde eine gute Übereinstimmung der simulierten Rissbildung mit den tatsächlichen Rissbildern beobachtet. Im zweiten Teil des Projekts wurden Verfahren zur experimentellen Beurteilung von Verpressankern für Lehmsteinmauerwerk erprobt. Die Versuchsergebnisse zeigten, dass die gewählten Versuchsabläufe mit Betrachtung der Verformungen bzw. Relativverschiebungen der Ankerkomponenten und des Mauwerwerks geeignet sind, die am häufigsten wiederkehrenden Versagensarten zu bestimmen und Traglastkurven für Verpressanker zu erstellen. KW - Baustoffe KW - Lehmsteinmauerwerk KW - Druckversuch KW - Schubversuch KW - Versagensmechanismen KW - numerische Modellierung KW - Ankerauszugsversuch PY - 2016 SN - 978-3-433-03131-5 SN - 0170-4958 VL - 41. Jahrgang, Kap. 1.2.3 SP - 534 EP - 536 PB - Wilhelm Ernst & Sohn, Verlag für Architektur und technische Wissenschaften GmbH & Co. KG CY - Berlin AN - OPUS4-37208 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Yukhvid, V. A1 - Gorshkov, V. A1 - Miloserdov, P. A1 - Skachkova, N. A1 - Alymov, M. I. A1 - Nolze, Gert A1 - Epishin, A. T1 - Synthesis of Molybdenum and Niobium Mono- and Binary Silicides by the Method of SHS-Metallurgy JF - Advanced engineering materials N2 - The process of self-propagating high-temperature synthesis of the Mo–Nb–Si silicides from the powder mixtures has been investigated. Based on performed experiments, the composition of powder mixtures as well as technological parameters are proposed which provide the synthesis of monosilicides MoSi₂, NbSi₂, and binary silicides Mo₁-хNbxSi₂ with different ratios of Nb/Mo by adding different contents of MoO₃ and Nb₂O₅. Microstructure and phase compositions of the obtained silicide ingots are characterized by scanning electron microscopy, electron probe microanalysis, X-ray diffraction, and backscatter electron diffraction. KW - Synthesis KW - EBSD KW - XRD PY - 2016 DO - https://doi.org/10.1002/adem.201600334 SN - 1438-1656 SN - 1527-2648 SP - 1 EP - 6 PB - Wiley-VCH Verlag GmbH & Co. KGaA CY - Weinheim AN - OPUS4-37209 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Sebastian Hanns-Otto A1 - Hertwig, Andreas A1 - Repo, P. A1 - Savin, H. A1 - Rosu, Dana-Maria A1 - Beck, Uwe T1 - Wide-spectrum dielectric functions of ALD deposited oxides relevant for photovoltaics N2 - Silicon surface passivation with atomic layer deposited (ALD) thin films has gained more and more interest in the PV community in recent years. With ALD good film quality, accurate thickness control and conformity are reached. Furthermore, ALD is capable of coating difficult substrates such as nanostructured surfaces with the same accuracy as flat surfaces. A variety of materials such as Al2O3, TiO2 and HfO2 demonstrate good surface passivation quality both for front and rear surface of silicon solar cells. In addition of providing good surface passivation, thin films with high refractive index e.g. HfO2, TiO2 and AlN can act simultaneously as antireflection coatings when applied on the front surface of the device. Hence, ALD thin films can reduce both electrical and reflective losses in solar cells. Thorough investigation of the optical properties of these layers is crucial for several reasons related to their production and use. Optical measurements provide a fast, easy, non-destructive, and in situ capable approach to quality assurance for photovoltaic devices. As the function of the final device is optical, optimisation of the device performance relies strongly on the knowledge of the wide-range dielectric function of the thin layers. In this contribution, we determined the optical constants of ALD generated layers of AlN, Al2O3, TiO2, and HfO2 in a wide spectral range covering the near ultraviolet and the mid-infrared regions by means of spectroscopic ellipsometry. By combining data from a UV-Vis-NIR ellipsometer (Woollam M2000DI) and an FTIR ellipsometer (Sentech Sendira), we can determine the optical constants alongside with the layer thicknesses from one large set of spectroscopic measurements. We consider this a contribution to the metrological treatment of stratified and structured thin films in the optical range by polarisation-sensitive measurement methods. T2 - International conference on spectroscopic ellipsometry (ICSE 7) CY - Berlin, Germany DA - 06.06.2016 KW - ALD (atomic layer deposited) KW - Ellipsometry KW - Photovoltaic KW - Solar Cell KW - HfO2 KW - Aln KW - Al2O3 KW - TiO2 PY - 2016 AN - OPUS4-37222 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grauel, Bettina A1 - Würth, Christian A1 - Wiesholler, L. M. A1 - Hirsch, T. A1 - Resch-Genger, Ute T1 - Nd as sensitizer in NaYF4:Yb,Er,Nd tri-doped upconversion nanocrystals N2 - In recent years, upconversion nanocrystals (UCNC) have shown great promise for biological and medical applications, mainly because of their excitation in the NIR region, which provides minimum fluorescence background and a rather deep penetration into biological samples, as opposed to excitation in the visible or UV region. Moreover, they show a multitude of characteristic narrow emission bands as basis for ratiometric measurements. Commonly, Yb is the sensitizer of choice, because of a comparatively high absorption cross section, simple energy scheme, and rather efficient energy transfer to the activator, mostly Er, Tm or Ho. A main disadvantage of the use of Yb as sensitizer for biological and medical applications is its absorption band at 976 nm and hence the use of an excitation wavelength at which water has a non-negligible absorption. This can lead to significant sample heating, especially at long illumination times or high excitation power densities, and thus, tissue damage or even cell death. A possible solution is the tri-doping of UCNC with Nd as sensitizer, which can be excited efficiently at around 800 nm, where water absorption is at minimum. The use of Nd as a sensitizer and Yb as a bridge between Nd and the activator Er in NaYF₄ nanocrystals is a relatively new way to overcome the problems of heating of samples in an aqueous environment. Disadvantages can arise from the tri-doping, which can favor non-radiative relaxation due to the more complicated excitation process compared to e.g., simple Yb,Er-doped UCNC, which might lower the upconversion quantum yields in these tri-doped systems. In order to quantify clear advantages, NaYF₄:Yb,Er,Nd nanoparticles were synthesized and spectroscopically studied using an 8 W 804 nm laser diode and a custom-designed Edinburgh instruments FSP980 spectrometer. Wavelength-dependent studies of the emission intensities and the decay kinetics of these tri-doped UCNC at different excitation power densities and excitation pulse widths revealed the clear advantages of preventing water absorption on measurable luminescence signals. We were able to show the influence of pulse width and excitation power density on the luminescence intensities and decay kinetics lifetimes at different emission wavelengths. Additionally, we can clearly discern power density-dependent and independent peaks in the emission spectra. In summary, we demonstrate that the tri-doping of NaYF₄:Yb,Er,Nd nanoparticles is a very promising approach to render UCNC more efficient and to make them better suitable for biological and medical applications requiring measurements in aqueous environment. T2 - UPCON 2016 Conference CY - Breslau, Poland DA - 23.05.2016 KW - UCNP KW - Nd-sensitizer KW - excitation power density PY - 2016 AN - OPUS4-37224 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Miccoli, Lorenzo A1 - Fontana, Patrick A1 - Silva, N. A1 - Kocadag, R. A1 - Cederqvist, Ch. A1 - Krefft, O. A1 - Qvaesching, D. T1 - UHPC-AAC/CLC composite panels with self-cleaning properties. Materials and production technology T2 - Proceedings of Smart Facades Materials Conference 2016 N2 - The aim of this study is to show the development of a façade composite panel combining either an autoclaved aerated concrete or a cellular lightweight concrete insulation layer with a box-type external ultra-high performance concrete (UHPC) supporting layer. The paper presents the materials characteristics of the different components and the production technology of the panel. The efficiency of surface modifications of the materials forming the external shell of the panel is reported. The activation of self-cleaning properties is described. The test results showed that the most efficient way to use the water-repellent agent is its application on the substrate before the concrete cast. Concerning the production technology, the preliminary studies showed more advantages of a twostep manufacturing procedure of the UHPC boxes than a one-step procedure. T2 - Smart Facades Materials Conference CY - Wels, Austria DA - 24.02.2016 KW - facade composite panels KW - ultra-high performance concrete (UHPC) KW - autoclaved aerated concrete (AAC) KW - cellular lightweight concrete (CLC) KW - self-cleaning properties PY - 2016 SP - 1 EP - 14 PB - OÖ Energiesparverband CY - Wels, Austria AN - OPUS4-37185 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, P. A1 - Fontana, Patrick A1 - Miccoli, Lorenzo A1 - Ziegert, C. T1 - Partial safety factors for earth block masonry N2 - In the beginning of the 1980s earth building has undergone a renaissance, which nowadays leads to an increasing use of load-bearing earth constructions and in particular, earth block masonry. At present there are no common structural standards according to the semi-probabilistic calculation concept, which is the state-of-the-art in European standards. A solid database is needed for the determination of the materials partial safety factor. Therefore, compressive strength tests were carried out with two types of earth blocks and two types of prefabricated earth mortar. The evaluation showed that the variation of the compressive strength was remarkably less than expected, which seems to indicate high quality standards of the components earth block and mortar with regard to industrial production. On the basis of these results and together with the reliability method, a partial safety factor for earth block masonry subjected to compression was determined. The main aim of the research was the development of a first valid database for material parameters of earth block masonry with particular regard to statistical characteristics. The results showed that a common calculation method for earth block masonry based on partial safety factors following the valid masonry construction standard is feasible. T2 - Terra 2016 - XIIth World Congress on Earthen Architectures CY - Lyon, France DA - 11.07.2016 KW - earth block masonry KW - partial safety factors KW - uniaxial compression test PY - 2016 AN - OPUS4-37186 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ferraioli, M. A1 - Miccoli, Lorenzo A1 - Abruzzese, D. A1 - Mandara, A. T1 - Dynamic characterisation and seismic assessment of medieval masonry towers JF - Natural Hazards N2 - The paper investigates the dynamic characterisation, the numerical model tuning and the seismic risk assessment of two monumental masonry towers located in Italy: the Capua Cathedral bell tower and the Aversa Cathedral bell tower. Full-scale ambient vibration tests under environmental loads are performed. The modal identification is carried out using techniques of modal extraction in the frequency domain. The refined 3D finite element model (FEM) is calibrated using the in situ investigation survey. The FEM tuning is carried out by varying the mechanical parameters and accounting for the restraint offered by the neighbouring buildings and the role of soil–structure interaction. The assessment of the seismic performance of the bell towers is carried out through a nonlinear static procedure based on the multi-modal pushover analysis and the capacity spectrum method. Through the discussion of the case studies, the paper shows that the modal identification is a reliable technique that can be used in situ for assessing the dynamic behaviour of monumental buildings. By utilising the tuned FEM of the towers, the theoretical fundamental frequencies are determined, which coincide with the previously determined experimental frequencies. The results from seismic performance assessment through a pushover analysis confirm that the masonry towers in this study are particularly vulnerable to strong damage even when subjected to seismic events of moderate intensity. KW - masonry towers KW - ambient vibration tests KW - dynamic characterisation KW - seismic assessment PY - 2016 DO - https://doi.org/10.1007/s11069-016-2519-2 SN - 1573-0840 SN - 0921-030X VL - 86 SP - Suppl. 2, S489 EP - S515 PB - Springer AN - OPUS4-37187 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Frei, J. A1 - Suwala, H. A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael T1 - Bestimmung der Rissanfälligkeit von hochfesten Stählen beim Widerstandspunktschweißen JF - Mechanical Testing N2 - Die stetig zunehmenden Anforderungen an Kraftstoffverbrauch, Schadstoffemission, sowie passive Sicherheit haben die Automobilindustrie vor Herausforderungen gestellt, die nur durch einen konsequenten Einsatz moderner hochfester Stahlwerkstoffe zu bewältigen sind. Obgleich eine generelle Eignung dieser Stähle für das Widerstandspunktschweißen (WPS) gegeben ist, kann es durch verschiedene externe Einflüsse im betrieblichen Umfeld zur Rissbildung in der Schweißverbindung kommen. Der Einfluss dieser Risse auf die mechanischen Eigenschaften ist derzeit nicht hinreichend genau erfasst, so dass häufig die Vorgabe einer rissfreien Schweißverbindung besteht. Die Kenntnis der Rissanfälligkeit der verarbeiteten Materialkombinationen sowie von ungünstigen Schweißparametern ist daher für viele Unternehmen von erheblicher wirtschaftlicher Bedeutung. Im Rahmen des FOSTA Projekts P921 „Entwicklung eines Verfahrens zur Bestimmung der Rissanfälligkeit von hochfesten Stählen beim Widerstandspunktschweißen“ wurde ein Ansatz zur Bestimmung der Rissanfälligkeit von WPS-Verbindungen hochfester Stähle entwickelt. Mittels einer hydraulischen Vorrichtung unter Zugbelastung wurden geschweißte, rissbehaftete Proben optisch ausgewertet. Das Verfahren ist geeignet, um ein Werkstoffranking bezüglich der Rissanfälligkeit beim Widerstandspunktschweißen für Werkstoffe aufzustellen. KW - Widerstandspunktschweißen KW - Werkstoffranking KW - Rissanfälligkeit KW - hochfeste Stähle KW - Liquid Metal Embrittlement KW - Lötrissigkeit PY - 2016 DO - https://doi.org/10.3139/120.110904 VL - 58 IS - 7-8 SP - 612 EP - 616 PB - Carl Hanser Verlag CY - München AN - OPUS4-37161 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Miccoli, Lorenzo A1 - Drougkas, T. A1 - Müller, U. T1 - In-plane behaviour of rammed earth under cyclic loading: experimental testing and finite element modelling JF - Engineering Structures N2 - The purpose of this paper is to numerically simulate the in-plane behaviour of rammed earth walls under cyclic shear-compression tests. The experimental testing allowed obtaining the maximum horizontal loads, the displacement capacity and the level of non-linear behaviour of the respective loaddisplacement relationships as well as the failure modes. The calibration of the numerical model (finite element method) was carried out based on the experimental results. Within this framework, a micromodelling approach was considered. The behaviour of the rammed earth material was simulated using a total strain rotating crack model. A Mohr-Coulomb failure criterion was used to reproduce the behaviour of the interfaces between the layers. Although the numerical results achieved a satisfactory agreement with the experimental results a sensitivity analysis of the parameters involved was performed. The sensitivity analysis aimed at determining which parameters of the model have a significant impact in the model’s results. As expected the sensitivity analysis pointed out that the sliding failure occurrence is mainly influenced by two parameters of the interface elements: the interface tensile strength fit and the friction angle u. Moreover the cohesion c and the layers thickness showed a limited effect on the shear behaviour. It should be noted that the results mentioned above are related to the cases where a significant level of vertical compressive stress r is employed. KW - rammed earth KW - in-plane loads KW - shear behaviour KW - cyclic shear-compression tests KW - finite element modelling KW - pseudo-dynamic tests PY - 2016 DO - https://doi.org/10.1016/j.engstruct.2016.07.010 SN - 0141-0296 SN - 1873-7323 VL - 125 SP - 144 EP - 152 PB - Elsevier Ltd. AN - OPUS4-37165 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Fontana, Patrick T1 - Bewährte Baustoffe mit neuen Eigenschaften - Beton mit funktionalen Oberflächen JF - GIT Labor-Fachzeitschrift N2 - Beton ist als Massenbaustoff vielseitig einsetzbar. Eine der neuesten Entwicklungen ist Ultrahochleistungsbeton (UHPC). Seine besonderen Eigenschaften ermöglichen eine zusätzliche Funktionalisierung der Oberflächen, da annähernd beliebige Mikrostrukturen exakt abgeformt werden können. So lassen sich beispielsweise Fassadenelemente aus UHPC bereits bei ihrer Herstellung im Betonfertigteilwerk mit selbstreinigenden Oberflächen ausrüsten. Eine andere Möglichkeit ist eine Anwendung als Datenspeicher. Wie das Beispiel der Schallplatte aus UHPC zeigt, lassen sich Muster, die hier die Schallinformationen enthalten, exakt von einer Matrize kopieren. KW - Baustoffe KW - Funktionale Betonoberfläche KW - Ultrahochleistungsbeton KW - Lotuseffekt KW - Selbstreinigende Oberfläche KW - Mikrostrukturierung PY - 2016 SN - 0016-3538 IS - 8 SP - 36 EP - 38 PB - Wiley-VCH Verlag GmbH & Co. KGaA, GIT Verlag AN - OPUS4-37166 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kühne, Hans-Carsten A1 - Raupach, M. A1 - Bastert, H. A1 - Eßer, A. A1 - Gehlen, Ch. A1 - Hintzen, W. A1 - Hohberg, I. A1 - Reichling, K. A1 - Westendarp, A. A1 - Wiens, U. A1 - Wolff, L. T1 - Neue Regeln braucht das Land - Die neue Instandhaltungs-Richtlinie des Deutschen Ausschuss für Stahlbeton (DAfStb), Teil 1 JF - B+B Bauen im Bestand N2 - Mit Veröffentlichung der europäischen Normenreihe EN 1504 in den Jahren 2004 bis 2008 mussten in Deutschland die bisherigen nationalen Regelungen für die Instandsetzung von standsicherheitsrelevanten Betonbauteilen angepasst werden. Im vorliegenden Entwurf der neuen Instandhaltungs-Richtlinie wurden die Hinweise zur Planung und Durchführung von Instandsetzungsmaßnahmen aus der Instandsetzungsrichtlinie des DAfStb von 2001 entsprechend überarbeitet und aufgrund neuer Erkenntnisse ergänzt. Außerdem wurde das Regelwerk um Gesichtspunkte der Instandhaltung erweitert, sodass die Aspekte Wartung, Inspektion und Verbesserung nun in Anlehnung an DIN 31051 berücksichtigt werden. Zudem wurden Regelungen aus der ZTV-ING sowie der ZTV-W übernommen. Im ersten Teil dieses Artikels geben wir einen Überblick über die Gliederung und wesentliche neue Inhalte wie die Ausweitung der Instandsetzungsprinzipien. KW - Betoninstandsetzung PY - 2016 SN - 2190-9504 VL - 39. Jahrgang IS - 2.2016 SP - 16 EP - 23 PB - Verlagsgesellschaft Rudolf Müller GmbH & Co. KG CY - Köln AN - OPUS4-37167 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kühne, Hans-Carsten A1 - Raupach, M. A1 - Bastert, H. A1 - Eßer, A. A1 - Gehlen, Ch. A1 - Hintzen, W. A1 - Hohberg, I. A1 - Reichling, K A1 - Westendarp, A. A1 - Wiens, U. A1 - Wolff, L. T1 - Das Bauwerk stellt die Anforderungen - Die neue Instandhaltungs-Richtlinie des Deutschen Ausschusses für Stahlbeton (DAfStb), Teil 2 JF - B+B Bauen im Bestand N2 - In einer Artikelserie stellen wir die neue Instandhaltungs-Richtlinie des Deutschen Ausschusses für Stahlbeton (DAfStb) vor. Im zweiten Teil geht es um Betonersatz- und Oberflächenschutzsysteme sowie Rissfüllstoffe. Es werden als Folge des EuGH-Urteils vom Oktober 2014 zukünftig keine Anforderungen an Bauprodukte mit dem Nachweis über allgemeine bauaufsichtliche Prüfzeugnisse gestellt. Stattdessen werden auf Basis der Anforderungen individueller Bauwerke notwendige Merkmale von Bauprodukten für die Instandsetzung definiert. Außerdem wird Teil 3 der neuen Instandhaltungs-Richtlinie "Ausführung der Instandsetzung und Überwachung" vorgestellt. Neu ist hier die Einführung von Überwachungsklassen, die sich aus der Art des instand zu setzenden Betonbauteils (standsicherheitsrelevant oder nicht) und der auszuführenden Arbeiten ergeben, zum Beispiel Instandsetzung oder Verstärkung. Am Ende dieses Artikels wird kurz der 4. Teil der neuen Instandhaltungs-Richtlinie erläutert. KW - Betoninstandsetzung PY - 2016 SN - 2190-9504 VL - 39. Jahrgang IS - 3.2016 SP - 51 EP - 55 PB - Verlagsgesellschaft Rudolf Müller GmbH & Co. KG CY - Köln AN - OPUS4-37168 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Braun, Ulrike A1 - Lorenz, Edelgard A1 - Weimann, Christiane A1 - Sturm, Heinz A1 - Karimov, I. A1 - Ettl, J. A1 - Meier, R. A1 - Wohlgemuth, W. A. A1 - Berger, H. A1 - Wildgruber, M. T1 - Mechanic and surface properties of central-venous port catheters after removal: A comparison of polyurethane and Silicon rubber materials JF - Journal of the Mechanical Behavior of Biomedical Materials N2 - Central venous port devices made of two different polymeric materials, thermoplastic polyurethane (TPU)and silicone rubber (SiR), were compared due their material properties. Both naïve catheters as well as catheters after removal from patients were investigated. In lab experiments the influence of various chemo-therapeutic solutions on material properties was investigated, where as the samples after removal were compared according to the implanted time inpatient. The macroscopic,mechanical performance was assessed with dynamic, specially adapted tests for elasticity. The degradation status of the materials was determined with common tools of polymer characterisation, such as infrared spectroscopy, molecular weight measurements and various methods of thermal analysis. The surface morphology was an alysed using scanning electron microscopy. A correlation between material properties and clinical performance was proposed. The surface morphology and chemical composition of the polyurethane catheter materials can potentially result in increased susceptibility of the catheter to bloodstream infections and thrombotic complications. The higher mechanic failure,especially with increasing implantation time of the silicone catheters is related to the lower mechanical performance compared to the polyurethane material as well as loss of barium sulphate filler particles near the surface of the catheter. This results in preformed microscopic notches, which act as predetermined sites of fracture. KW - Thermoplastic polyurethane (TPU) KW - Silicone rubber (SiR) KW - Catheters KW - Central venous access port KW - Complication KW - Structure propertyrelationship KW - Mechanical testing PY - 2016 DO - https://doi.org/10.1016/j.jmbbm.2016.08.002 SN - 1751-6161 SN - 1878-0180 VL - 64 SP - 281 EP - 291 PB - Elsevier Ltd. AN - OPUS4-37178 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Liehr, Sascha A1 - Krebber, Katerina T1 - Applications and prospects for distributed sensing using polymer optical fibres T2 - Transforming the Future of Infrastructure Through Smarter Information, Proceedings of the International Conference on Smart Infrastructure and Construction N2 - One of the unique advantages of polymer optical fibres (POF) is that they can be used to measure very high strain values up to 100 % and beyond exceeding the strain limits of silica fibre-based sensor principles. In this paper the distributed strain measurement capabilities of POF based on backscatter change evaluation are summarized and distributed backscatter measurement technologies are intro-duced. Application examples in the structural health monitoring (SHM) field are presented: a promising approach is the integration into technical textiles for high-strain measurement in earthwork structures and crack detection in buildings. The potential of POF for future applications in SHM such as distributed relative humidity sensing is discussed. T2 - International Conference on Smart Infrastructure and Construction CY - Cambridge, UK DA - 27.06.2016 KW - Strain measurement KW - Structural health monitoring KW - OTDR KW - Polymer Optical Fibre KW - Distributed sensing PY - 2016 UR - http://www.icevirtuallibrary.com/doi/abs/10.1680/tfitsi.61279.093 SN - 978-0-7277-6127-9 DO - https://doi.org/10.1680/tfi tsi.61279.093 SP - 93 EP - 98 PB - ICE Publishing CY - London, UK AN - OPUS4-37230 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Liehr, Sascha A1 - Krebber, Katerina T1 - Applications and prospects for distributed sensing using polymer optical fibres N2 - One of the unique advantages of polymer optical fibres (POF) is that they can be used to measure very high strain values up to 100 % and beyond exceeding the strain limits of silica fibre-based sensor principles. In this paper the distributed strain measurement capabilities of POF based on backscatter change evaluation are summarized and distributed backscatter measurement technologies are intro-duced. Application examples in the structural health monitoring (SHM) field are presented: a promising approach is the integration into technical textiles for high-strain measurement in earthwork structures and crack detection in buildings. The potential of POF for future applications in SHM such as distributed relative humidity sensing is discussed. T2 - International Conference on Smart Infrastructure and Construction CY - Cambridge, UK DA - 27.06.2016 KW - Strain measurement KW - Structural health monitoring KW - OTDR KW - Polymer Optical Fibre KW - Distributed sensing PY - 2016 UR - http://www.icevirtuallibrary.com/doi/abs/10.1680/tfitsi.61279.093 DO - https://doi.org/10.1680/tfitsi.61279.093 AN - OPUS4-37231 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lohrer, Christian T1 - Recent Activities and Decisions of the forum of notified bodies for pyrotechnics N2 - Overview about the recent activities of the notified bodies for pyrotechnics under 2013/29/EU and the respective impacts on the work of the market surveillance authorities N2 - Überblick über die Tätigkeiten der benannten Stellen Pyrotechnik unter 2013/29/EU und deren Auswirkungen auf die Arbeit der Marktüberwachnungsbehörden. T2 - 10th Meeting of the Administrative Coordination group for Pyrotechnic Articles (AdCo-PA) CY - Buxton, UK DA - 26.10.2016 KW - Konformitätserklärung KW - Pyrotechnik KW - Schutzabstände KW - Kennzeichnung KW - Konformitätsbewertung KW - Declaration of conformity KW - Pyrotechnics KW - Safety distances KW - Labelling KW - Conformity assessment PY - 2016 AN - OPUS4-37233 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kulla, Hannes A1 - Greiser, Sebastian A1 - Benemann, Sigrid A1 - Rademann, K. A1 - Emmerling, Franziska T1 - In Situ Investigation of a Self-Accelerated Cocrystal Formation by Grinding Pyrazinamide with Oxalic Acid JF - Molecules N2 - A new cocrystal of pyrazinamide with oxalic acid was prepared mechanochemically and characterized by PXRD, Raman spectroscopy, solid-state NMR spectroscopy, DTA-TG, and SEM. Based on powder X-ray diffraction data the structure was solved. The formation pathway of the reaction was studied in situ using combined synchrotron PXRD and Raman spectroscopy. Using oxalic acid dihydrate the initially neat grinding turned into a rapid self-accelerated liquid-assisted grinding process by the release of crystallization water. Under these conditions, the cocrystal was formed directly within two minutes. KW - in situ KW - cocrystal KW - mechanochemistry KW - pyrazinamide KW - hydrate PY - 2016 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-372357 DO - https://doi.org/10.3390/molecules21070917 SN - 1420-3049 VL - 21 IS - 7 SP - Article 917, 1 EP - 9 AN - OPUS4-37235 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klinge, A. A1 - Roswag-Klinge, E. A1 - Ziegert, C. A1 - Fontana, Patrick A1 - Richter, Matthias A1 - Hoppe, Johannes ED - Habert, G. ED - Schlueter, A. T1 - Naturally ventilated earth timber constructions T2 - Expanding boundaries: Systems thinking for the built environment - Sustainable Built Environment (SBE) N2 - Earth, timber, fibre boards and insulation materials based on wooden and other natural fibres offer a variety of properties beneficial for eco innovative constructions that are able to improve the energy and resource efficiency of buildings. Due to their porosity, natural building materials are vapour active and are able to buffer moisture. In combination with highly insulated and airtight but vapour permeable building envelopes, modern earth-timber constructions provide stable indoor humidity levels and can therefore be naturally ventilated while achieving highest energy efficiency standards. Experimental evidence suggests that monitored pilot buildings in Berlin do show healthy indoor air humidity levels (around 50%) in wintertime, while mechanically ventilated buildings demonstrate significantly lower values (around 25%), which have to be considered as uncomfortable and unhealthy. The application of building materials being poor in chemical emissions, particularly volatile organic compounds (VOC) and radon, improves the indoor air quality further, so that intermittent ventilation twice a day will be sufficient to provide healthy indoor air quality. The air quality in critical rooms (e.g. small bedrooms), demonstrating a smaller air volume, should be monitored if appropriate ratios of room size to occupancy level cannot be realised. Through night time ventilation in summer, vapour active earth-timber constructions provide evaporative cooling (humidity adsorption at night time and desorption during the day). As a result, indoor temperatures of earth-timber buildings range around 8 °C below the outside temperature peak, when an appropriate glazing ratio is reflected. The EU funded research project H-house is investigating various construction materials regarding water vapour adsorption as well as emission and absorption of harmful substances. Based on this investigation new wall constructions are designed to provide a healthier indoor environment. T2 - Sustainable Built Environment (SBE) Regional Conference - Expanding Boundaries: Systems Thinking for the Built Environment CY - Zurich, Switzerland DA - 15.06.2016 KW - Building materials KW - Climate control through building elements KW - Hygroscopic earthen and wooden materials KW - Natural ventilation KW - Airtight building KW - Low emissions PY - 2016 SN - 978-3-7281-3774-6 DO - https://doi.org/10.3218/3774-6 SP - 674 EP - 681 PB - vdf Hochschulverlag und der ETH Zürich CY - Zürich AN - OPUS4-37201 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Boateng, Francis Twumasi A1 - Ewert, Uwe A1 - Kannengießer, Thomas A1 - Zscherpel, Uwe A1 - Griesche, Axel A1 - Kromm, Arne A1 - Hohendorf, Stephan A1 - Redmer, Bernard T1 - Real-time radiography for observation of crack growth during GTA (Gas Tungsten Arc) welding JF - Welding in the world N2 - In situ crack detection in the mushy zone and the solid weld of a gas tungsten arc (GTA) weld using X-ray imaging during welding is a new research area for NDT inspection. Usually, NDT flaw detection is done after the complete solidification of the weld seam. In this paper, we present the use of real-time radiography with a minifocus X-ray source (YXLON X-ray tube Y.TU 225-D04) and a 75μm pixel size digital detector array (Dexela 1512) for the acquisition of 2D radiographic images by a sequence of exposures with time intervals of 80 ms for hot crack detection during single pass bead-on-plate GTA welding of 3 mm thick plates of aluminium alloy AlMgSi (6060). An analysis of the crack distribution in the weld sample is conducted from the acquired 2D radiographs and its corresponding 3D volumetric reconstruction achieved by linear coplanar digital laminography. This in situ approach opens new possibilities in the field of hot crack research by having the direct information of both the crack initiation and growth and its correlation to the welding parameters. KW - Hot cracking KW - Radiography KW - GTA welding KW - Aluminium alloys KW - Real-time operation PY - 2016 DO - https://doi.org/10.1007/s40194-016-0351-7 SN - 0043-2288 SN - 1878-6669 VL - 60 IS - 5 SP - 931 EP - 937 AN - OPUS4-37128 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Brosig, Laura T1 - Method-verification and optimisation of the standardised assessment of odour intensity regarding ISO 16000-28 N2 - Besides measurement of VOC emissions also the evaluation of odour emissions and the perceived intensity of odours gains in importance. Due to difficulties detected in the measurement method of the perceived intensity described in (ISO 16000-28, 2012) the introduction of “reference” odours will be recommended for the training of panellists and as basis for interlaboratory comparisons. In order to generate the “reference” odours standard liquid substances were directly injected into the main gas flow provided to the panellists. One of the substances tested was ethyl acetate. A pre-evaluation was conducted with six untrained panellists and has shown that ethyl acetate is potentially suitable as reference odour. For further validation of those “reference” odours they additionally will be provided to and evaluated by trained panellists of well established-measurement institutes. T2 - Indoor Air 2016 CY - Ghent, Belgium DA - 03.07.2016 KW - odour assessment KW - perceived odour intensity KW - reference odour KW - emission testing KW - building products PY - 2016 AN - OPUS4-37134 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rosu, Dana-Maria A1 - Hertwig, Andreas A1 - Beck, Uwe A1 - Rotella, H. A1 - Nolot, E. T1 - Optical investigation of ZnO and doped ZnO thin films N2 - In the search for highly efficient, low-cost, non-toxic, transparent conductive oxides (TCOs) suitable for large area applications for photovoltaics, ZnO and ZnO-related materials have received considerable attention. In the present work, Al and Ga doped ZnO films on oxidized Si substrates are characterized using mainly variable angle spectroscopic ellipsometry; additional optical and non-optical techniques were employed to confirm and support the ellipsometric models considered. The samples were obtained by means of pulsed chemical vacuum deposition (CVD) and atomic layer deposition (ALD). As known from previous studies the presence of dopants in ZnO thin films generally induce significant changes in the optical, electrical and morphological properties. We present our findings for a series of Al and Ga doped ZnO layers with different concentrations of the dopants, discussing their influence on the optical and electrical properties. T2 - 7th International Conference on Spectroscopic Ellipsometry (ICSE-7) CY - Berlin, Germany DA - 06.06.2016 KW - doped ZnO KW - ellipsometry KW - optical properties KW - transparent conducting oxide PY - 2016 AN - OPUS4-37135 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Harald A1 - Hoffmann, Katrin A1 - Schwibbert, Karin A1 - Sameith, Janin A1 - Toepel, Jörg A1 - Resch-Genger, Ute T1 - Polymeric sensors as imaging tools for local pH in biofilm for early detection of microbial induced corrosion T1 - Polymersensoren als Werkzeug für die Bildgebung von lokalen pH in Biofilmen für die frühzeitige Erkennung von mikrobiell induzierter Korrosion N2 - Microbial induced corrosion (MIC) is a crucial problem in many technical plants as well as fuel tanks, leading to considerable damage and huge financial losses. Successful prevention of MIC requires the localization of first signs of corrosion as well as the identification of factors influencing the corrosion process.1 Hence, there is a growing need for sensitive and preferably inexpensive tools that enable the early detection of MIC. Of high importance are methods, which provide spatially and time-resolved information and allow the study of changes on metal surfaces as prerequisites for a more detailed analysis of ongoing corrosion processes at a MIC-affected site.2 In this respect, also the determination of corrosion rates can be of interest for the possible prevention of MIC. T2 - 11th International Symposium on Polymer Therapeutics CY - Valencia, Spain DA - 23.05.2016 KW - Bildgebung KW - Mikrobiell induzierte Korrosion KW - Nanosensor KW - Imaging KW - Microbial induced corrosion KW - Nanosensor PY - 2016 AN - OPUS4-37138 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Harald A1 - Hoffmann, Katrin A1 - Schwibbert, Karin A1 - Sameith, Janin A1 - Toepel, Jörg A1 - Resch-Genger, Ute T1 - Polymeric sensors as imaging tools for local pH in biofilm for early detection of microbial induced corrosion N2 - Microbial induced corrosion (MIC) is a crucial problem in many technical plants as well as fuel tanks, leading to considerable damage and huge financial losses. Successful prevention of MIC requires the localization of first signs of corrosion as well as the identification of factors influencing the corrosion process.1 Hence, there is a growing need for sensitive and preferably inexpensive tools that enable the early detection of MIC. Of high importance are methods, which provide spatially and time-resolved information and allow the study of changes on metal surfaces as prerequisites for a more detailed analysis of ongoing corrosion processes at a MIC-affected site.2 In this respect, also the determination of corrosion rates can be of interest for the possible prevention of MIC. T2 - 11th International Symposium on Polymer Therapeutics CY - Valencia, Spain DA - 23.05.2016 KW - Bildgebung KW - Mikrobiell induzierte Korrosion KW - Nanosensor KW - Imaging KW - Microbial induced corrosion PY - 2016 AN - OPUS4-37139 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kotschate, Daniel A1 - Gohlke, Dirk A1 - Eisentraut, M. T1 - Reference block design for high resolution ultrasound immersion tank N2 - In respect of modern approaches in material sciences and highly increased requirements on materials on safety relevant components, quality management and non-destructive testing reclaims a steadily increased meaning. The destructive meaning of measuring the degree of purity is defined in DIN EN 10247 through metallurgical investigations, especially microsections. For and comparable, but non-destructive testing due ultrasonic testing, the material the SEP 1927 is a well-defined industry standard. A novel and alternative way of reference block construction was focused by this work. The proposed amendments, regarding the manufactoring and machining, are less time and cost consuming. Verified by measurements the presented reference block fits the same acoustical characteristics and the requirements of the guideline. T2 - World Conference on Non-Destructive Testing CY - Munich, Germany DA - 13.06.2016 KW - Immersion tank testing KW - SEP 1927 KW - Degree of purity KW - High resolution ultrasonic testing PY - 2016 AN - OPUS4-36850 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kotschate, Daniel A1 - Gohlke, Dirk A1 - Eisentraut, Mark T1 - Reference block design for high resolution ultrasound immersion tank T2 - WCNDT 2016 N2 - In respect of modern approaches in material sciences and highly increased requirements on materials on safety relevant components, quality management and non-destructive testing reclaims a steadily increased meaning. The destructive meaning of measuring the degree of purity is defined in DIN EN 10247 through metallurgical investigations, especially microsections. For and comparable, but non-destructive testing due ultrasonic testing, the material the SEP 1927 is a well-defined industry standard. A novel and alternative way of reference block construction was focused by this work. The proposed amendments, regarding the manufacturing and machining, are less time and cost consuming. Verified by measurements the presented reference block fits the same acoustical characteristics and the requirements of the guideline. T2 - 19th World Conference on Non-Destructive Testing CY - Munich, Germany DA - 13.06.2016 KW - SEP 1927 KW - Degree of purity KW - High resolution ultrasonic testing KW - Immersion tank testing PY - 2016 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-368512 VL - 2016 SP - Paper X15, 1 EP - 4 AN - OPUS4-36851 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Selleng, Christian A1 - Meng, Birgit A1 - Fontana, Patrick T1 - Phase composition and strength of thermally treated UHPC N2 - Thermal treatment improves the excellent properties of UHPC. Recent studies have shown that an increase in compressive strength of more than 30 % is possible. However, the accurate conditions of thermal treatment for a maximal strength are considered as yet undetermined. A multitude of parameters can be varied: temperature, pressure, water saturation, and duration of the process steps. These parameters influence the phase development and in consequence the macroscopic properties of UHPC. The primary objective of the presented study was the optimisation of the conditions for thermal treatment, concerning compressive strength. It focuses on pre-storage time and duration of the treatment at defined temperatures and pressures (90 °C and 185 °C/1.1MPa). As expected, experimental results showed a fundamental change of phase composition in hydrothermally treated UHPC in comparison to standard cured UHPC: Ettringite decomposes at higher temperatures and is absent after thermal treatment; the amount of portlandite and clinker phases decreases. The change of phase composition is accompanied by increased compressive strength. Experimental studies of calcium-silicate-systems at hydrothermal conditions predict the formation of the crystalline C-S-H phase tobermorite. In fact, this is a typical phase occurring in other hydrothermally treated calcium-silicate-systems like Autoclaved Aerated Concrete (AAC). Commonly, high strength is attributed to the presence of tobermorite; however, in the presented study tobermorite was not detected in the hydrothermally treated UHPC. Therefore, tobermorite cannot be responsible for the increased strength of hydrothermally treated UHPC. In conclusion the development of phases and strength of UHPC at hydrothermal conditions differs fundamentally from AAC and the experimental studies with water saturation. Results of these systems cannot be transferred to UHPC. In thermally treated UHPC, the hydration of clinker is enhanced and the puzzolanic reaction is intensified. Hence, more C-S-H is formed that fills pores and cracks, leading to a denser structure and finally to higher strength. T2 - 4th International Symposium on Ultra-High Performance Concrete and High Performance Materials (HiPerMat) CY - Kassel, Germany DA - 09.03.2016 KW - Ultra-high performance concrete KW - Thermal treatment KW - Compressive strength KW - Tobermorite KW - C-S-H KW - Building Materials PY - 2016 AN - OPUS4-36853 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF ED - Schmidt, Wolfram ED - Priebe, Nsesheye Susan T1 - Advances in cement and concrete technology in Africa N2 - Welcome to the 2nd International Conference on Advances in Cement and Concrete Technology in Africa (ACCTA 2016), January 27– 29, 2016, held at White Sands Hotel, Dar es Salaam, Tanzania. The first ACCTA conference that took place in January 2013 in Johannesburg was a result of an African-European collaborative research project. Due to the success of this conference, it was announced that a triennial international conference is necessary, with the next conference scheduled to take place once again in Johannesburg. Within the organisation of the conference, unfortunately some unforeseeable events arose, which would lead to either a delay of the conference in Johannesburg until 2018 or a change of venue. The great response from the international scientific community supported the option to maintain the originally scheduled date. With the support of the local organisation committee from the University of Dar es Salaam and the contributions from the University of the Witwatersrand and the University of Zagreb the conference was shifted to Dar es Salaam. Despite the new boundary framework, we are extremely happy that it was possible to arrange an outstanding and excellent scientific programme. Therefore we would like to thank in particular the keynote speakers and all members of the international scientific community, as well as other delegates that supported the conference by their contributions and attendance. This shows us how significantly important the African cement and concrete market is for the entire global community. Africa can become a spearhead for the future of construction with cement and concrete. The continent exhibits an enormous construction potential and due to the relatively short history of building with these materials, innovations can be adopted and adapted unbiased and without influence of stakeholders, traditions, and complicated networks of regulations. This is a fertile ground for the existing promising generation of engineers and decision makers for re-inventing cement and concrete in the best possible way. There is no global optimum solution for concrete. The best solution in Africa is not the best solution in Europe or another part of the world, and the best solution in one particular African country is diverging from the best solution in another African country depending upon resources, supply chains, infrastructure, construction needs, traditions, available manpower, skills and technologies. Nevertheless, we can globally support our objectives to build future oriented and sustainable construction solutions by mutually learning from each other. In order to tackle the future challenges and build more sustainably and innovatively with concrete, we need to enhance interdisciplinary and cross-national skills and create networks between experts and decision makers globally. ACCTA offers this kind of platform, and we are happy to announce that the conference reaches a high impact in the world. Delegates and speakers come from more than 40 countries in the world originating from all continents. Besides the technical content there will be plenary discussions on the most relevant topics of future binder technologies and standards and product safety with outstanding expert panellists. We want to wish all delegates a successful conference and hope that this book can be a significant contribution for a future oriented and better concrete technology; in Africa and the entire world. Welcome to Dar es Salaam, Tanzania. T2 - 2nd International Conference on Advances in Cement and Concrete Technology in Africa CY - Dar es Salaam, Tanzania DA - 27.01.2016 KW - Cement KW - Concrete KW - Africa KW - Sustainability KW - Construction PY - 2016 SN - 978-3-9817502-3-2 N1 - Geburtsname von Priebe, Nsesheye Susan: Msinjili, N. S. - Birth name of Priebe, Nsesheye Susan: Msinjili, N. S. VL - 2 SP - 1 EP - 634 PB - BAM CY - Berlin, Germany AN - OPUS4-36859 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stockmann, Jörg M. A1 - Hertwig, Andreas A1 - Beck, Uwe T1 - Visualization of low-contrast surface modifications: thin films, printed pattern, laser-induced changes, imperfections, impurities, and degradation N2 - Industrial quality control (QC) nowadays requires the visualization of surface modifications from the macro-scopic to the microscopic or even nanoscopic scale. This is a prerequisite to the evaluation of functionality and reliability, the detection of defects and their separation of artefacts. The diversity of applications ranges from low-E glazings and solar panels, micro- and optoelectronics, micro- and smart devices to sensor-on-chip and lab-on-chip systems [1]. Optical microcopy (light, confocal laser scanning, white light interference) as established QC-tool is operated at normal incidence, i.e. p- and s-polarization are undistinguishable. Either light-intensity in terms of grey scale and colour or intensity-correlated effects of phase shifts are used. In case of ellipsometry, operated at oblique incidence, p- and s-polarization matter, and amplitude ratios and phase shifts upon reflection are measured. Hence, information content must be much higher. The visualization of surface modifications may be very challenging for coating/substrate systems of either al-most identical optical constants, e.g. transparent films on substrates of the same material, or minor film thick-ness, substance quantity and affected area, e.g. ultra-thin or island films. Ellipsometry gives access to the con-trast of intensity (I), amplitude ratio (Ψ), and phase shift (Δ) with nanometer-scaled vertical and micrometer-scaled lateral sensitivity, one is able to identify tiny changes within an unmodified surface. As both mapping ellipsometry (ME) and imaging ellipsometry (IE) are operated in the optical far-field, surface inspection is also possible on the macroscopic scale. Near the Brewster-angle of the bare, undamaged, clean, and fresh substrate, the contrast to add-on and sub-off features is superior. Fig. 1 shows three examples of ellipsometric imaging, i.e. a thin SnO:Ni film on SiO2/Si (Fig. 1a), a dried stain of an anti-body solution on cyclo-olefin-polymer (COP) shown in Fig. 1b, and a polyimide film residue on SiO2/Si (Fig. 1c). For all of these examples, ellipsometry provides much better contrast between substrate and surface modification than optical microscopy, sometimes primarily caused by the oblique incidence (Figs. 1a and 1c), in other cases related to the phase sensitivity of ellipsometry (Fig. 1b). Other examples are laser surface modifications and the corrosion of glass. In these cases, optical microscopy and IE yield to similar results, how-ever only ellipsometry gives access to modelling. Further investigated coating/substrate systems are 100Cr6 steel, native oxide on silicon, borosilicate glass, and the polymer polycarbonate with deposited films of graphene and ta-C:H, printed and dried pattern of liquids such as water, cleaning agents, and dissolved silicone. Besides imaging ellipsometry, referenced spectral ellipsometry (RSE) has been applied, combining the advantages of both optical microscopy (fast measurement) and ellipsometry (high sensitivity to tiny modifications). T2 - International Conference on Spectroscopic Ellipsometry (ICSE-7) CY - Berlin, Germany DA - 06.06.2016 KW - Ellipsometry KW - Thin films KW - Impurities KW - Degradation PY - 2016 AN - OPUS4-37068 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Resch-Genger, Ute T1 - Standardization of fluorescence measurements: Design, development, validation, and fabrication of format-adaptable fluorescence standards for intensity, spectral, and temporal quantities N2 - Photoluminescence techniques are amongst the most widely used tools in the material and life sciences, with new and exciting applications continuously emerging, due to their many advantages like comparative ease of use, unique sensitivity, non-invasive character, and potential for multiplexing, remote sensing, and miniaturization. Drawbacks are , however, signals, that contain unwanted wavelength- and polarization contributions from instrument-dependent effects, which are time-dependent due to the aging of instrument components, and difficulties to measure absolute fluorescence intensities. Thus, there is a considerable need for standards for intensity, spectral, and temporal fluorescence quantities to meet the increasing need for instrument performance validation and global trends to harmonize physicochemical measurements. In this respect, instrument calibration strategies together with different types of fluorescence standards are presented as well as design concepts for robust, easy-to-use, and format-adaptable fluorescence standards useable for the determination of different fluorescence parameters and a broad variety of fluorescence techniques. T2 - SALSA-Kolloquien CY - Berlin, Germany DA - 07.06.2016 KW - Fluorescence KW - Standard KW - Quality assurance KW - Spectral correction KW - Quantum yield PY - 2016 AN - OPUS4-37070 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bonse, Jörn A1 - Höhm, S. A1 - Kirner, Sabrina A1 - Rosenfeld, A. A1 - Krüger, Jörg T1 - Laser-induced periodic surface structures (LIPSS) - A scientific evergreen T2 - OSA Technical Digest (2016) N2 - The current state in the field of laser-induced periodic surface structures (LIPSS, ripples) is reviewed. Their formation mechanisms are analyzed in ultrafast experiments (time-resolved diffraction and polarization controlled double-pulse experiments) and technological applications are demonstrated. T2 - Conference on Lasers and Electro-Optics (CLEO) - Science and Innovations 2016 CY - San Jose, CA, USA DA - 05.06.2016 KW - Laser materials processing KW - Optics at surfaces KW - Ultrafast phenomena KW - Laser-induced periodic surface strcutures (LIPSS) KW - Femtosecond laser ablation PY - 2016 SN - 978-1-943580-11-8 DO - https://doi.org/10.1364/CLEO_SI.2016.STh1Q.3 SP - STh1Q.3, 1 EP - 2 PB - Optical Society of America AN - OPUS4-37072 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Miccoli, Lorenzo A1 - Fontana, Patrick A1 - Gardei, André A1 - Ziegert, C. A1 - Perrone, Ch. A1 - Kaiser, C. A1 - Gerrard, Ch. ED - Feiglstorfer, H. T1 - Analysis and diagnosis of earthen buildings: the case of Ambel preceptory in Aragon, Spain T2 - earth construction & tradition N2 - This study presents diagnostic techniques to assess the structural vulnerability of earthen buildings. Medieval structures at Ambel (near Zaragoza, Spain), once a preceptory or monastic house belonging to the Military Orders, provide a useful case study. After more than a thousand years of construction, failure and repair from the 10th century to the present day, Ambel preceptory today is characterised by marked inhomogeneities: construction materials and structural typologies are juxtaposed, with structural discontinuities at the interfaces between construction phases. This paper argues that, while static analysis is an essential prerequisite before a suitable maintenance program can be defined, no evaluation of the structural behaviour of any historic building can ignore an understanding of the building’s history. KW - historical earthen building KW - rammed earth KW - material characterisation KW - static monitoring PY - 2016 SN - 978-3-900265-34-2 VL - 1 SP - 201 EP - 229 PB - IVA-Verlag CY - Vienna, Austria AN - OPUS4-37076 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pavlenko, E. S. A1 - Sander, M. A1 - Mitzscherling, Steffen A1 - Pudell, J. A1 - Zamponi, F. A1 - Rössle, M. A1 - Bojahr, A. A1 - Bargheer, M. T1 - Azobenzene – functionalized polyelectrolyte nanolayers as ultrafast optoacoustic transducers JF - Nanoscale N2 - We introduce azobenzene-functionalized polyelectrolyte multilayers as efficient, inexpensive optoacoustic transducers for hyper-sound strain waves in the GHz range. By picosecond transient reflectivity measurements we study the creation of nanoscale strain waves, their reflection from interfaces, damping by scattering from nanoparticles and propagation in soft and hard adjacent materials like polymer layers, quartz and mica. The amplitude of the generated strain ε∼5×10−4 is calibrated by ultrafast X-ray diffraction. KW - Picosecond acoustic KW - Ultrafast optoacoustic KW - Nanolayer KW - Polyelectrolyte PY - 2016 DO - https://doi.org/10.1039/c6nr01448h SN - 2040-3364 SN - 2040-3372 VL - 8 IS - 27 SP - 13297 EP - 13302 AN - OPUS4-37079 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Liu, J.-Y. A1 - Hou, X.-N. A1 - Tian, Y. A1 - Jiang, L. A1 - Deng, S. A1 - Röder, B. A1 - Ermilov, Eugeny T1 - Photoinduced energy and charge transfer in a bis(triphenylamine)-BODIPY-C60 artificial photosynthetic system JF - RSC Advances N2 - Triphenylamines (TPAs), boron dipyrromethenes (BODIPYs) and fullerenes C60 are excellent building blocks for the design of artificial photosynthetic systems. In the present work, we report the synthesis, characterization and detailed photophysical studies of a novel (TPA)2–BODIPY–C60 tetrad in polar and nonpolar solvents. The absorption spectrum of this compound covered virtually the entire visible Region (350–700 nm) and could be interpreted as a superposition of the spectra of individual components. Upon TPA-part excitation, a fast and very efficient excitation energy transfer (EET) delivers the excitation to the BODIPY moiety resulting in complete quenching of the TPA first excited singlet state as well as the appearance of the BODIPY fluorescence. The efficiency of EET process was estimated to be 1. Direct or indirect (via EET) excitation of the BODIPY-part of the tetrad is followed by photoinduced charge transfer to the charge-separated state BODIPY+–C60- irrespective of the solvent used. In polar N,N-dimethylformamide (DMF)charge recombination occurs directly to the ground state with the Charge recombination rate, kCR, slower than 108 s-1, whereas in nonpolar toluene (TOL) a small energy gap between the charge-separated state and first excited singlet state of the BODIPY moiety facilitates the back charge transfer process. The latter results in the appearance of thermally activated delayed fluorescence. The rate of charge separation was found to be ca. 2 times faster in TOL than in DMF. KW - Charge transfer KW - Energy transfer KW - Artificial photosynthesis KW - BODIPY KW - TPA KW - Fullerene C60 PY - 2016 DO - https://doi.org/10.1039/c6ra06841c SN - 2046-2069 VL - 6 IS - 62 SP - 57293 EP - 57305 AN - OPUS4-37080 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pasternak, H. A1 - Launert, B. A1 - Rhode, Michael A1 - Kannengießer, Thomas T1 - Advanced residual stress assessment of plate girders by welding simulation: An overview N2 - Welded plate girders are used in heavy steel construction, industrial buildings and bride construction. Residual stresses are present in all plate structures. They are mainly caused by welding. In addition, they influence the load bearing capacity of these welded components. However, Eurocode (EC) does not provide any specific residual stress patterns for consideration of residual stress impact on load capacity. Hence, the decision for a particular problem has to be made by the designer. Many codes, including EC 3, permit the use of non-linear finite element analysis (FEA) for the design of structures. This contribution gives an overview on recent research topics: modeling, experimental measuring and evaluation of residual stresses as well as welding simulation tools and simplified methodologies for assessment of weld residual stresses. T2 - Modern Building Material, Structures and Techniques - MBMST 2016 CY - Vilnius, Lithuania DA - 26.05.2016 KW - Residual stresses KW - Welding KW - Measurement KW - Numerical modeling KW - Component PY - 2016 AN - OPUS4-37028 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Launert, B. A1 - Rhode, Michael A1 - Pasternak, H. A1 - Kannengießer, Thomas T1 - Welding residual stresses in high-strength steels: experimental results N2 - Welded plate girders are used in heavy steel construction, industrial buildings and bride construction. Residual stresses are present in all plate structures. They are mainly caused by welding. In addition, they influence the load bearing capacity of these welded components. However, Eurocode (EC) does not provide any specific residual stress patterns for consideration of residual stress impact on load capacity. Hence, the decision for a particular problem has to be made by the designer. Many codes, including EC 3, permit the use of non-linear finite element analysis (FEA) for the design of structures. For that purpose, the contribution gives an overview on recent results derived from welded I-girders made from mild steel S355 and high-strength steel S690QL. Weld residual stresses have been investigated by X-ray diffraction (XRD) on small-scale specimen. In addition, residual stresses of welded component-like I-girders have been studied using the sectioning technique. The results confirmed the beneficial effect of certain edge preparation of the plates by flame cutting prior to welding. High-strength steels like the S690 can contribute to both: increased load capacity and decreased influence of weld residual stresses. T2 - International Colloquium on Stability and Ductility of Steel Structures CY - Timisoara, Romania DA - 30.05.2016 KW - Welding KW - Residual stresses KW - High-strength steel KW - Experimental results PY - 2016 AN - OPUS4-37031 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Preissel, Marcel A1 - Vrana, J. T1 - Ermittlung der Auffindwahrscheinlichkeit von Reflektoren in Abhängigkeit der Rastergröße bei der Ultraschallprüfung großer Schmiedestücke JF - ZfP-Zeitung N2 - Die Auswirkung des Prüfrasters nach der DGZfP Richtlinie US 07:2014 auf die Auffindwahrscheinlichkeit von Reflektoren wird untersucht. Hierzu werden Simulationsrechnungen durchgeführt, mit dem Ziel, die Abhängigkeit der Unterbewertung von Größe und Tiefenlage von Reflektoren in Bezug auf das Prüfraster zu ermitteln und experimentell zu überprüfen. In zwei Simulationsreihen wird der Einfluss des Prüfrasters auf die Suche von Anzeigen und auf die Bewertung von Anzeigen ermittelt und bewertet. Auf Basis der Simulationsrechnungen wird eine POD-Analyse mit dem Ziel durchgeführt, die Auffindwahrscheinlichkeit von Reflektoren in Bezug zur Rastergüte Rn zu setzten und die Nachweisgrenze zu ermitteln. KW - Schmiedeteile KW - Ultraschall KW - Probability of detection KW - Prüfraster PY - 2016 UR - http://www.dgzfp.de/Dienste/ZfP-Zeitung IS - 150 SP - 52 EP - 57 AN - OPUS4-37032 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pech, Anja A1 - Wilke, Olaf A1 - Horn, Wolfgang A1 - Jann, Oliver T1 - Analysis of very volatile organic compounds (VVOC) with thermal desorption GC-MS T2 - Proceedings of Indoor Air 2016, The 14th international conference of Indoor Air Quality and Climate N2 - Most VVOC were rarely considered in the evaluation of construction products. (Salthammer, 2014) In Germany this will change because the latest version of the German AgBB scheme for health evaluation (2015) now include VVOC, e.g. ethyl acetate and ethanol. In this study selected compounds were tested with the procedure described in ISO 16017 and a method for measuring VVOC with thermal desorption was developed. Three different adsorbents Tenax TA, Carbograph 5TD and Carbopack X were tested to analyse VVOC according to ISO 16017. For the tested VVOC, Carbograph 5TD showed the best results under the chosen analytical conditions. T2 - Indoor Air 2016, The 14th international conference of Indoor Air Quality and Climate CY - Gent, Belgium DA - 03.07.2016 KW - Thermal desorption KW - VVOC KW - Carbograph 5TD KW - Carbopack X PY - 2016 SP - Paper 889, 1 EP - 2 AN - OPUS4-37035 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wollschläger, Nicole A1 - Tasdemir, Z. A1 - Häusler, Ines A1 - Leblebici, Y. A1 - Österle, Werner A1 - Alaca, B. E. T1 - Determination of the elastic behavior of silicon nanowires within a scanning electron microscope JF - Journal of Nanomaterials N2 - Three-point bending tests were performed on double-anchored, <110> silicon nanowire samples inside a scanning electron microscope (SEM) via a micromanipulator equipped with a piezo-resistive force sensor. Representing the upper and lower boundaries achievable in a consistent manner, silicon nanowires with widths of 35 nm and 74 nm and a height of 168 nm were fabricated. The nanowires were obtained monolithically along with their 10-m-tall supports through a top-down fabrication approach involving a series of etching processes. Hence, no interface compliance was introduced between supports and nanowires. Exact nanowire dimensions and cross-sectional features were determined by transmission electron microscopy (TEM) following sample preparation through focused ion beam (FIB) machining. Conducting the experiments inside an SEM chamber further raised the opportunity of the direct observation of any deviation from ideal loading conditions such as twisting, which was taken into consideration in simulations. Measured force-displacement behavior was observed to exhibit close resemblance to simulation results obtained by finite element modeling, when the bulk value of 169 GPa was taken as the modulus of elasticity for <110> silicon. Hence, test results show neither any size effect nor evidence of residual stresses for the considered nanoscale objects. The increased effect of the native oxide with reduced nanowire dimensions was captured as well. Thus this very simple in-situ testing method was found to be an alternative to elaborate AFM measurements on geometrically formidable nanostructures. The results demonstrate the applicability of the developed fabrication approach to the incorporation of silicon nanowires in functional micromechanical devices. KW - Silicon nanowire KW - Elastic behavior KW - Scanning electron microscope KW - Mechanical properties PY - 2016 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-370383 DO - https://doi.org/10.1155/2016/4905838 VL - 2016 SP - Article 4905838, 1 EP - 6 PB - Hindawi Publishing Corporation AN - OPUS4-37038 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - de Oliveira Guilherme Buzanich, Ana A1 - Radtke, Martin A1 - Reinholz, Uwe A1 - Riesemeier, Heinrich A1 - Emmerling, Franziska T1 - Time- & spatial-resolved X-ray absorption fine structure (XAFS) spectroscopy in a single-shot – new analytical possibilities for in situ material characterization JF - Journal of Synchrotron Radiation N2 - A new concept that comprises both time- and lateral-resolved X-ray absorption fine-structure information simultaneously in a single shot is presented. This uncomplicated set-up was tested at the BAMline at BESSY-II (Berlin, Germany). The primary broadband beam was generated by a double multilayer monochromator. The transmitted beam through the sample is diffracted by a convexly bent Si (111) crystal, producing a divergent beam. This, in turn, is collected by either an energy-sensitive area detector, the so-called color X-ray camera, or by an area-sensitive detector based on a CCD camera, in θ-2θ geometry. The first tests were performed with thin metal foils and some iron oxide mixtures. A time resolution of lower than 1 s together with a spatial resolution in one dimension of at least 50 µm is achieved. KW - Time resolution KW - Single-shot XAFS PY - 2016 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-370892 DO - https://doi.org/10.1107/S1600577516003969 SN - 1600-5775 IS - 23 SP - 769 EP - 776 PB - International Union of Crystallography CY - Chester, UK AN - OPUS4-37089 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR T1 - Amts- und Mitteilungsblatt, Band 46, Heft 2 T2 - Amts- und Mitteilungsblatt T3 - Amts- und Mitteilungsblatt der BAM - 2/2016 PY - 2016 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-370952 SN - 0340-7551 VL - 46 IS - 2 SP - 55 EP - 139 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin, Germany AN - OPUS4-37095 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pistol, Klaus A1 - Gluth, Gregor A1 - Rickard, W. T1 - Mechanische Hochtemperatureigenschaften von flugaschebasierten Geopolymerbetonen JF - Bautechnik N2 - Als umweltschonende Alternative zu portlandzementgebundenen Betonen werden derzeit in der Betonindustrie und in der Baustoffforschung Betone mit alkaliaktivierten Bindemitteln, sog. Geopolymerbetone, intensiv erforscht. Die auf industriellen Reststoffen wie Flugasche und Hüttensand basierenden anorganischen Bindemittel weisen bei geeigneter Zusammensetzung einen hohen Widerstand gegenüber aggressiven Salzlösungen und Säuren auf. Als Grundlage für den rechnerischen Nachweis der Tragfähigkeit von brandbeanspruchten Betonbauteilen auf Basis von alkaliaktivierten Bindemitteln werden deshalb an der Bundesanstalt für Materialforschung und -prüfung (BAM) die mechanischen Hochtemperatureigenschaften von flugaschebasierten Geopolymerbetonen systematisch untersucht. Die bis zu 750 °C erhitzten Probekörper mit quarzitischer und leichter Gesteinskörnung zeigen einen Festigkeitsverlust bis ca. 300 °C, der auf entwässerungsbedingte Mikrorissbildung zurückgeführt werden kann. Bei weiter zunehmender Temperatur steigt aufgrund von Sinterungsprozessen ab ca. 500 °C die Festigkeit der untersuchten Geopolymerbetone wieder an. Diese im Vergleich zu herkömmlichem Beton günstigere Materialeigenschaft eröffnet potenziell auch Anwendungsmöglichkeiten in brandschutztechnisch kritischen Infrastrukturbereichen. Die Ergebnisse der thermomechanischen Prüfungen werden für numerische Bauteilberechnungen als temperaturabhängige Spannungs-Dehnungs-Beziehungen aufbereitet. N2 - At present, concretes based on alkali-activated binders, socalled geopolymer concretes, are investigated intensively in the building materials industry and by the research community as environmentally friendly alternative to Portland cementbased concretes. These inorganic binders, which are based on industrial by-products such as fly ash and ground granulated blast furnace slag, exhibit high resistance against corrosive acids and salts, if properly designed. The mechanical properties of fly ash-based geopolymer concretes at high temperatures are subject of systematic investigations at the Bundesanstalt für Materialforschung und -prüfung (BAM) to create a basis for the structural design of fire exposed concrete members based on alkali-activated binders. The concrete specimens, produced with quartz aggregates or lightweight aggregates and heated to a maximum temperature of 750 °C, exhibited a decrease of compressive strength up to temperatures of ca. 300 °C, attributed to formation of microcracks caused by dehydration. At higher temperatures the compressive strength of the investigated geopolymer concretes recovered partly, due to sintering processes starting from ca. 500 °C. Because of this beneficial property when compared to conventional concretes, geopolymer concretes can potentially be applied in infrastructure facilities where fire resistance is critical. From the results of the thermomechanical tests stress-strain relationships are derived that can be used for the structural design of members made from geopolymer concretes. KW - Geopolymerbeton KW - Hochtemperatureigenschaften KW - Feuerwiderstand KW - Spannung-Dehnungs-Beziehung PY - 2016 DO - https://doi.org/10.1002 / bate.201600038 SN - 1437-0999 VL - 93 IS - 8 SP - 521 EP - 530 PB - Ernst & Sohn CY - Berlin AN - OPUS4-37114 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Recknagel, Christoph T1 - Was müssen flexible Fahrbahnübergänge leisten? N2 - Fahrbahnübergänge sind das bautechnisch-konstruktive Verbindungsglied von der Fahrbahn der freien Strecke auf Ingenieurbauwerke und anschließend wieder zurück auf die freie Strecke. Sowohl aus ökonomischen (Baukosten), ökologischen (Lärmschutz) als auch aus verkehrssicherheitstechnischen Gründen wurden in jüngster Zeit sogenannte flexible belagsähnliche Übergangskonstruktionen entwickelt. Der Beitrag benennt die materialtechnischen und konstruktiven Anforderungen als notwendige Grundlage für den Nachweis der Funktionsfähigkeit unter höchsten Verkehrsbeanspruchungen. Gleichzeitig werden neuartige material- und leistungsidentifizierende Kennwerte vorgestellt und deren Einfluss auf Funktionsfähigkeit und Dauerhaftigkeit diskutiert. Als versuchstechnische Grundlagen kommen durch die BAM entwickelte bzw. adaptierte Untersuchungsmethoden zur Anwendung. Die Interpretation der Untersuchungsergebnisse und deren Beitrag und Bedeutung für qualitätssichere europäische bzw. nationale Bauprodukte werden der Zielgruppe Verkehrsplanern, Straßenbaubehörden, Ausführenden und Nutzern erläutert. Schlussfolgerungen aus den veränderten baurechtlichen Rahmenbedingungen und Erfahrungen der BAM bei der europäischen Zulassung von Übergangskonstruktionen werden vorgestellt. T2 - Ingenieursymposium der Straßenbauingenieure Kanton Bern, Schweiz CY - Bern, Switzerland DA - 18.03.2016 KW - Dehnfugensysteme KW - Innovative lärmarme Übergangskonstruktionen PY - 2016 AN - OPUS4-37119 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, U. A1 - Miccoli, Lorenzo A1 - Fontana, Patrick T1 - Development of a lime based grout for crack repair in earthen constructions JF - Construction and Building Materials N2 - The study presents the results from the development of a grouting material based on hydrated lime with addition of pozzolana, which is referred to as hydraulic lime, suitable for the repair of cracks in a variety of earthen building techniques. The goal was to develop a material also compatible with earthen structures exposed to dynamic loads. The grouting mortar was designed to be adaptable in strength properties and at the same time to have sufficient robustness for preparation and use on the construction site. Results showed a satisfactory performance of the grout concerning fresh and hardened mortar properties as well as injectability. KW - Earthen construction KW - Lime based grout KW - Cracks grouting KW - Rheology KW - Strength KW - Adhesion PY - 2016 DO - https://doi.org/10.1016/j.conbuildmat.2016.02.030 SN - 0950-0618 VL - 110 SP - 323 EP - 332 PB - Elsevier AN - OPUS4-37064 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Miccoli, Lorenzo A1 - Fontana, Patrick A1 - Silva, N. A1 - Kocadag, R. A1 - Cederqvist, Ch. A1 - Kreft, O. A1 - Qvaesching, D. T1 - UHPC-AAC/CLC composite panels with self-cleaning properties. Materials and production technology N2 - The aim of this study is to show the development of a façade composite panel combining either an autoclaved aerated concrete or a cellular lightweight concrete insulation layer with a box-type external ultra-high performance concrete (UHPC) supporting layer. The paper presents the materials characteristics of the different components and the production technology of the panel. The efficiency of surface modifications of the materials forming the external shell of the panel is reported. The activation of self-cleaning properties is described. The test results showed that the most efficient way to use the water-repellent agent is its application on the substrate before the concrete cast. Concerning the production technology, the preliminary studies showed more advantages of a two-step manufacturing procedure of the UHPC boxes than a one-step procedure. T2 - Smart Facade Materials Conference CY - Wels, Austria DA - 24.02.2016 KW - Facade composite panels KW - Ultra-high performance concrete (UHPC) KW - Autoclaved aerated concrete (AAC) KW - Cellular lightweight concrete (CLC) KW - Slef-cleaning properties PY - 2016 AN - OPUS4-37066 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Miccoli, Lorenzo A1 - Fontana, Patrick A1 - Ziegert, C. A1 - Müller, P. T1 - Calibration of partial safety factors for earth block masonry under compression loading N2 - The goal of the present study is to assess the feasibility to develop a first reliable database of materials parameters for Earth Block Masonry (EBM). The database is crucial when defining the materials safety factors. In the first part an experimental campaign of compressive tests were carried out on two types of earth block and two types of earth mortar. The results showed that the mean variation of the compressive strength was remarkably less than expected. This low variation is related to a production with high quality standards of the materials employed. In the second part a partial safety factor for EBM under uniaxial compression was determined through the reliability method. The results proved the reliability of a common calculation method for EBM based on partial safety factors following the current standards. T2 - IB2MAC 2016 - 16th International Brick and Block Masonry Conference CY - Padua, Italy DA - 26.06.2016 KW - Earth block masonry KW - Partial safety factors KW - Uniaxial compression test PY - 2016 AN - OPUS4-37067 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pelkner, Matthias A1 - Stegemann, Robert A1 - Sonntag, Nadja A1 - Cabeza, Sandra A1 - Lyamkin, Viktor A1 - Bruno, Giovanni A1 - Skrotzki, Birgit A1 - Kreutzbruck, Marc T1 - Evaluation of high spatial resolution imaging of magnetic stray fields for early damage detection N2 - Metal magnetic memory (MMM) technique with associated ISO 24497-1:3 is gaining considerable interest in the magnetic NDT community. In contrast to traditional Magnetic Flux Leakage (MFL) testing, the inspection objects are not intentionally magnetized by an external magnetic field. Due to the physical coupling between mechanical stress and magnetization of ferromagnetic materials, it is assumed that the distribution of the residual MFL correspond to the internal stress of the specimen, or in the most general sense, to a degradation of the material. Usually, MMM measurements are performed by relatively bulky magnetic inspection sensors. The evaluation of local magnetic field distribution is limited thereby. Highprecision GMR (Giant Magneto Resistance) measurements in the micrometer regime can provide a higher degree of information due to better spatial resolution. We present a concise summary of studies on the correlation of magnetic structure and microstructure of steels. In particular, we compare residual stress measurements in S235JRC steel welds by means of neutron diffraction with high resolution magnetic field mappings. Results indicate a qualitative correlation between residual stresses and local stray field variation. In addition, stray field measurements of plastically deformed specimens for quasi-static and cyclic loading cases are discussed. The present study concludes that GMR sensors can detect inhomogeneous plastic deformations of S235JR steel in a very early stage, without specific signal processing according to the ISO 24497-1:3. T2 - QNDE - Review of Progress in Quantitative Nondestructive Evaluation CY - Atlanta, Georgia, USA DA - 18.07.2016 KW - NDT KW - MMM KW - GMR PY - 2016 AN - OPUS4-37101 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Resch-Genger, Ute A1 - Behnke, Thomas A1 - Moser, Marko A1 - Quevedo, Pablo A1 - Nirmalananthan-Budau, Nithiya A1 - Weigert, Florian A1 - Würth, Christian A1 - Hoffmann, Katrin A1 - Ermilov, Eugeny A1 - Pauli, Jutta T1 - Simple methods, validation concepts, and reference materials for the characterization of functional nanomaterials and microparticles N2 - The surface chemistry / functionalization of nanomaterials and microparticles largely controls the stability of these materials as well as their solubility and subsequent biofunctionalization and their interactions with biological systems. Moreover, in the case of some nanomaterials like semiconductor quantum dots or lanthanide-based upconversion nanocrystals, the ligand shell strongly affects their optical properties, e.g., via passivation of surface states and traps that favor luminescence quenching or the protection of surface atoms from quenching water molecules. This renders analytical methods for the quantification of surface groups like functionalities very important. Targets of broad interest are here amino, carboxyl, alkine and maleimide groups used for common bioconjugation reactions and typical ligands like thiols and polyethylene glycol (PEG) molecules of varying length, used for the tuning of material hydrophilicity and biocompatibility, minimization of unspecific interactions, prevention of biofouling, and enhancement of blood circulation times as well as surface-bound biomolecules like streptavidin or other biomolecules relevant e.g., for diagnostic assays. Here, we focus on simple optical methods relying on standard laboratory instrumentation, validated by method comparison and/or mass balances and present examples for their use for the characterization of different types of nanomaterials and microparticles. T2 - Innovationsforum Senftenberg CY - Senftenberg, Germany DA - 01.06.2016 KW - Surface chemistry KW - Functional group analysis KW - Thiol assay KW - Fluorescence KW - Nanomaterial KW - Nanoparticle KW - PEG KW - Ligand KW - Semiconductor quantum dot KW - Quantum yield KW - Quantification KW - Method validation KW - Integrating sphere spectroscopy KW - Fluorescence standard PY - 2016 N1 - Geburtsname von Nirmalananthan-Budau, Nithiya: Nirmalananthan, N. - Birth name of Nirmalananthan-Budau, Nithiya: Nirmalananthan, N. AN - OPUS4-37111 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Resch-Genger, Ute T1 - Applications and challenges of luminescence-based detection methods in the life and material sciences N2 - Luminescence-based detection methods, ranging from fluorescence spectroscopy for photophysical and mechanistic studies over sensing applications, chromatographic separation techniques and the microarray technology with fluorescence detection to fluorescence microscopy, flow cytometry, single molecule spectroscopy, and molecular imaging to integrating sphere spectroscopy, are among the most widely used methods in the life and material sciences. This is due to e.g., their unique sensitivity enabling the detection of single molecules, potential for multiplexing, ease of combination with spatial resolution, and suitability for remote sensing. Many of these advantages are closely linked to the choice of suitable molecular and nanoscale fluorescent reporters, typically required for signal generation. This includes organic dyes without and with sensor function, fluorophore-encoded polymeric and silica nanoparticles as well as nanocrystalline systems like semiconductor quantum dots and upconversion phosphors, emitting in the visible (vis), near-infrared (NIR), and IR (infrared). Current challenges present the environment sensitivity of most fluorophores, rendering fluorescence spectra, measured intensities/fluorescence quantum yields, and fluorescence decay kinetics matrix-dependent, and instrument-specific distortions of measured fluorescence signals that need to be considered for quantification and comparability of data, particularly fluorescence spectra. Here, current applications of luminescence-based methods and different types of reporters will be presented. In this context, suitable spectroscopic tools for the characteri-zation of the optical properties of fluorescent reporters and fluorophore-encoded microparticles, analytical tools for the determination of the surface chemistry of different types of particles, and different multiplexing strategies will be discussed. T2 - 9th Meeting of Engineering of Functional Interfaces CY - Wildau,Germany DA - 03.07.2016 KW - Fluorescence KW - Multiplexing KW - Lifetime KW - Nanomaterial KW - Nanoparticle KW - PEG KW - Ligand KW - Semiconductor quantum dot KW - Quantum yield KW - Quantification KW - Upconversion nanoparticle KW - Integrating sphere spectroscopy KW - NIR KW - IR KW - Fluorescence standard KW - Calibration PY - 2016 AN - OPUS4-37112 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maierhofer, Christiane A1 - Krankenhagen, Rainer A1 - Röllig, Mathias A1 - Riemer, Stefanie A1 - Gower, M. A1 - Baker, G. A1 - Lodeiro, M. A1 - Knazovicka, L. A1 - Blahut, A. A1 - Monte, C. A1 - Adibekyan, A. ED - Gutschwager, B. T1 - Characterisation of artificial and natural defects in fibre reinforced plastics designed for energy applications using active thermography T2 - DGZfP-Proceeding BB 158 of 19th World Conference on Non-destructive Testing (WCNDT) N2 - Amongst various other NDT methods, within the EMRP-project ‘VITCEA’ active thermography is validated for testing of CFRP and GFRP structures constructed for energy application. In this contribution, the optical and thermal properties of CFRP and GFRP reference defect artefact (RDA) and natural defects artefact (NDA) test specimens are characterized. Different excitation techniques and techniques for data analysis are compared for optimizing the number of detected defects. T2 - 19th World Conference on Non-destructive Testing (WCNDT) CY - Munich, Germany DA - 13.06.2016 KW - Active thermography KW - CFRP KW - GFRP KW - Artificial and natural defects PY - 2016 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-370207 UR - http://www.ndt.net/article/wcndt2016/papers/we2i4.pdf SN - 978-3-940283-78-8 VL - BB 158 SP - Paper we2i4, 1 EP - 9 PB - DGZfP CY - Berlin AN - OPUS4-37020 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Launert, B. A1 - Rhode, Michael A1 - Kromm, Arne A1 - Pasternak, H. A1 - Kannengießer, Thomas T1 - Measurement and numerical modeling of residual stress distribution in welded HSLA component-like I-girders N2 - Welded I-girders are used in many applications in steel construction, especially a tailored mixture of different plate thicknesses is difficult to manufacture by rolling. Residual stresses are mainly caused by welding and it is in most cases impractical to anneal the structures. Eurocode 3 (EC 3) does not provide any specific residual stress pattern. Hence, the decision for a particular problem has to be taken by the designer. Stability failures are often decisive in the design of steel beam and column members. Many standards, including EC 3, permit the use of non-linear FEA for the design of structures. Load influencing imperfections are mainly geometric deviations from the ideal shape and residual stresses(both due to assembly or weld manufacturing). Currently the residual stresses are considered by simplified “robust” procedures fixed in common standards(such as EC 3. Models mostly based on specimens from mild steel. Information about high-strength steels is less available for realistic assessment of residual stresses in full-scale I-girders. Hence, the scope of this work is the measurement of residual welding stresses on component-like I-girders S355 and S690 by sectioning method and global structural welding simulation. T2 - 69th IIW Annual Assembly, Meeting of Subcommission II-A CY - Melbourne, Australia DA - 10.07.2016 KW - Residual stress KW - Welding KW - Load bearing capacity KW - Numerical modeling KW - Measurement PY - 2016 AN - OPUS4-37025 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Launert, B. A1 - Rhode, Michael A1 - Kromm, Arne A1 - Pasternak, H. A1 - Kannengießer, Thomas T1 - Residual stress influence on the flexural buckling of welded I-girders N2 - Welded plate girders are used in heavy steel construction, industrial buildings and bride construction. Residual stresses are present in all plate structures. They are mainly caused by welding. In addiiton, they influence the load bearing capacity of these welded components. However, Eurocode (EC) does not provide any specific residual stress patterns for consideration of residual stress impact on load capacity. Hence, the decision for a particular problem has to be made by the designer. Many codes, including EC 3, permit the use of non-linear finite element analysis (FEA) for the design of structures. Recent developments in the last years, enabled the use of computerized models instead of laboratory experiments. In this scope, the FE-model should include all relevant factors properly. This important if considering that weld residual stresses can be a critical assessment factor. In addition, measuring of residual stresses is difficult, time consuming and expensive, it is therefore common to use founded distribution functions (e.g. Swedish BSK 99). Welding simulation tools offer new possibilities for a realistic assessment of weld-induced stresses and deformations. However, the modeling and the computational effort for large structural components is still not in a practicable range and a simplified methodology is in needed. As a result, a new approach (suitable for capacity analysis) is presented and detailed in the present contribution. T2 - 10th International Conference on Residual Stresses CY - Sydney, Australia DA - 03.07.2016 KW - Welding KW - Residual stresses KW - Load capacity KW - Numerical modeling KW - Component PY - 2016 AN - OPUS4-37027 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Boehm, Rainer A1 - Brackrock, Daniel A1 - Montag, Hans-Joachim A1 - Heckel, Thomas T1 - What is the benefit of the total focussing method and full matrix capture for ultrasonic imaging using the phased array technique N2 - In the last two decades automated ultrasonic inspection devices took over a lot of applications that prior have been carried out using manual inspection with the evaluation of A-scans only. In parallel phased array systems have been developed and brought to the market which offer detailed and fast control over the sound field. When applying automated inspection phased array systems for UT measurements imaging of the recorded data in combination with the probe positioning data is used for the evaluation of inspections. B-Scan, C-Scan and S-Scan images are typically used with this setup. For more sophisticated applications with linear arrays echo tomography and syntethic aperture focusing technique (SAFT) are well known methods and often applied for high resolution image reconstruction. Since channel count of phased array systems is constantly rising, matrix arrays with up to 256 elements entered the market. Signal processing in the matrix domain became 3D. Since some years the Total Focusing Method (TFM) is an additional imaging tool for these type of application. It is based on the Full Matrix Capture (FMC) using the elements of phased array probes as separate transmitters and receivers. In this contribution we discuss the common ground of SAFT and TFM as well as the differences between these imaging tools. The combined use of automated inspection, matrix arrays and signal processing for high resolution measurements is a challenging task where a very long parameter list has to be taken into account. Under which conditions which elements of the full matrix should be taken for the reconstruction for best results? Based on examples taken from measured and simulated echo signals it will be shown how image resolution can be optimized in dependence of different parameters like the distance between transmitters and receivers and their directivity patterns, the depth of echo source and the specimen geometry. T2 - 19th World Conference on Non-Destructive Testing CY - Munich, Germany DA - 13.06.2016 KW - Ultrasonic testing KW - Ultrasonic imaging KW - Phased array KW - Total focussing method KW - Full matrix capture PY - 2016 UR - https://www.wcndt2016.com/programme AN - OPUS4-37051 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Cabeza, Sandra A1 - Mishurova, Tatiana A1 - Bruno, Giovanni A1 - Garcés, G. T1 - The role of reinforcement orientation on the damage evolution of AlSi12CuMgNi + 15% Al2O3 under compression JF - Scripta Materialia N2 - Internal damage of an AlSi12CuMgNi alloy reinforced with planar random short fibres has been investigated after compression. This damage strongly influences the load partition between matrix and reinforcement. For fibres perpendicular to the applied load, breakage and interconnected cracks appear in significantly higher volume fraction than with fibres parallel to load. KW - Neutron Diffraction KW - Damage KW - Metal Matrix Composites KW - Load Partition KW - Synchrotron CT PY - 2016 DO - https://doi.org/10.1016/j.scriptamat.2016.05.023 SN - 1359-6462 VL - 122 SP - 115 EP - 118 PB - Elsevier B.V. CY - Amsterdam, Netherlands AN - OPUS4-36357 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pérez, P. A1 - Cabeza, Sandra A1 - Garcés, G. A1 - Adeva, Paloma T1 - Influence of long period stacking ordered phase arrangements on thecorrosion behaviour of extruded Mg97Y2Zn1 alloy JF - Corrosion Science N2 - The influence of second phase arrangements on the corrosion resistance of extruded Mg97Y2Zn1 alloy has been evaluated in a 0.1 M NaCl solution. The microstructure of the alloy consists of a high volume fraction of coarse elongated particles of a long period stacking ordered phase aligned along the extrusion direction. Corrosion rate of transversal sections is lower than that of longitudinal sections. Such difference is attributed to the different orientation of second phases in longitudinal and transversal sections. The corrosion front advances mainly perpendicular to the surface in transversal samples while perpendicular and lateral growth occur in longitudinal samples KW - passive films KW - Magnesium alloys KW - anodic dissolution PY - 2016 DO - https://doi.org/10.1016/j.corsci.2016.02.024 SN - 0010-938X VL - 107 SP - 107 EP - 112 PB - Elsevier Ltd. CY - Oxford, UK AN - OPUS4-36358 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grunewald, Thomas T1 - Nichtelektrischer Explosionsschutz - Mechanisch erzeugte Funken als Zündquelle N2 - Bei Geräten und Maschinen zur bestimmungsgemäßen Verwendung in explosionsgefährdeten Bereichen muss in der europäischen Union eine Zündgefahrenbewertung durchgeführt werden. Dabei müssen unter anderem die Gefahren von nichtelektrischen Zündquellen betrachtet werden, zu denen auch die mechanischen Schlagvorgänge gehören. Bei Schlagvorgängen kommt es infolge des Zusammenstoßes zweier Werkstücke zu einer Umwandlung der kinetischen Energie. Dabei erhöht sich die Temperatur der Werkstoffe an der Kontaktstelle und es kommt unter Umständen zu einem Abtrennvorgang kleiner Partikel erhöhter Temperatur. Sowohl die heißen Kontaktstellen als auch die abgetrennten Partikel können eine wirksame Zündquelle für ein explosionsfähiges Gasgemisch darstellen. Zur Festlegung von Grenzwerten wurden in der Norm EN 13463-1:2009 die Gasgemische anhand ihrer Explosionsgruppe klassifiziert und zu jeder Gruppe die maximale Energie des Schlagvorgangs festgelegt, unter derer die Entstehung einer wirksamen Zündquelle als unwahrscheinlich angenommen werden kann. T2 - Ausbildung zum Explosionsschutzbeauftragten (Veranst.-Nr. H050-04-385-6) CY - Haus der Technik (HdT) - Außeninstitut der RWTH Aachen, Essen, Germany DA - 12.04.2016 KW - Nichtelektrischer Explosionsschutz KW - Mechanisch erzeugte Funken KW - Schlagfunken KW - Nichtelektrische Funken PY - 2016 AN - OPUS4-36360 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hilgenberg, Kai A1 - Rethmeier, Michael A1 - Steinhoff, K. T1 - Surface structuring by pulsed laser implantation N2 - Micrometric surface topologies are required for a wide range of technical applications. While lowered surface features have been used for many years to improve the tribological behavior of contacting surfaces, there are also other fields of application, where the potential of elevated surface features is known, e. g. for metal forming tools. However, the demand for a high wear resistance of these structures often inhibits an industrial application. A solution is offered by structuring techniques that use additional material. A promising approach is the localized dispersing of hard ceramic particles by pulsed laser radiation, the so-called laser implantation. This paper describes the potential to adjust the geometry as well as the mechanical properties of laser implanted surfaces by means of microstructural and topological investigations. Afterwards, results of a wear test are given. It can be shown that dome-shaped or ring-shaped structures on a micrometric scale can be produced with high hardness and wear resistance. T2 - THERMEC 2016: International Conference on Processing & Manufacturing of Advanced Materials CY - Graz, Austria DA - 29.05.2016 KW - Laser implantation KW - Pulsed laser dispersing KW - Surface structuring PY - 2016 AN - OPUS4-36363 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krebs, Holger A1 - Schwarz, Silke T1 - Gefährdungsbeurteilung bei der Versagerbeseitigung N2 - Hauptsächliche Versagerursachen bei Sprengungen werden dargestellt. Des Weiteren wird diskutiert, welche Gefährdungen bei der Beseitigung von Versagern auftreten können und wie diese in eine Gefährdungsbeurteilung einfließen müssen. T2 - Sicherheitstagung - Wirtschaftsministerium Österreich CY - Fieberbrunn, Austria DA - 08.06.2016 KW - Versager KW - Gefährdungsbeurteilung PY - 2016 AN - OPUS4-36670 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krebs, Holger A1 - Schwarz, Silke T1 - Sind Streustrommessungen heute noch zeitgemäß und erforderlich? N2 - Elektrische Bewertungsmerkmale anhand von Zünderkennwerten sowie Streustromgefährdungen werden dargestellt. Methoden der Streustrommessung sowie Versuche mit elektrischen Zündern werden vorgestellt. T2 - Sicherheitstagung - Wirtschaftsministerium Österreich CY - Fieberbrunn, Austria DA - 08.06.2016 KW - Zünder KW - Gefährdung durch Streuströme PY - 2016 AN - OPUS4-36672 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Scherb, Tobias A1 - Kimber, S. A. J. A1 - Stephan, Christiane A1 - Henry, P. F. A1 - Schumacher, G. A1 - Escolástico, S. A1 - Serra, J. M. A1 - Seeger, J. A1 - Just, J. A1 - Hill, A.H. A1 - Banhart, J. T1 - Nanoscale order in the frustrated mixed conductor La5.6WO12-Delta JF - Journal of Applied Crystallography N2 - This article reports a comprehensive investigation of the average and local structure of La5.6WO12-δ, which has excellent mixed proton, electron and oxide ion conduction suitable for device applications. Synchrotron X-ray and neutron powder diffraction show that a cubic fluorite supercell describes the average structure, with highly disordered lanthanum and oxide positions. On average, the tungsten sites are sixfold coordinated and a trace [3.7 (1.3)%] of anti-site disorder is detected. In addition to sharp Bragg reflections, strong diffuse neutron scattering is observed, which hints at short-range order. Plausible local configurations are considered and it is shown that the defect chemistry implies a simple 'chemical exchange' interaction that favours ordered WO6 octahedra. The local model is confirmed by synchrotron X-ray pair distribution function analysis and EXAFS experiments performed at the La K and W L-3 edges. It is shown that ordered domains of similar to 3.5 nm are found, implying that mixed conduction in La5.6WO12-δ is associated with a defective glassy-like anion sublattice. The origins of this ground state are proposed to lie in the nonbipartite nature of the face-centred cubic lattice and the pairwise interactions which link the orientation of neighbouring octahedral WO6 sites. This 'function through frustration' could provide a means of designing new mixed conductors. KW - neutron diffraction KW - x-ray diffraction KW - proton conductors PY - 2016 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-366756 DO - https://doi.org/10.1107/S1600576716006415 SN - 1600-5767 VL - 49 IS - Issue 3 SP - 997 EP - 1008 PB - International Union of Crystallography CY - Chester, UK AN - OPUS4-36675 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Torge, Manfred A1 - Bücker, Michael A1 - Drachenberg, E. A1 - Müller, W. A1 - Schaaf, U. ED - Roemich, H. ED - Fair, L. T1 - Protection of stained-glass windows - case studies in Poland T2 - Recent Advances in Glass and Ceramics Conservation 2016 N2 - Several restoration projects of stained-glass windows have been performed in Lower Silesia (Poland) since 2010. The aim of the projects was to protect stained-glass windows against environmental impact of industial pollutants and acid rain by installing a protective glazing. The usefulness of protective glazing has been proved by climate measurements and determination of environmental impact before and after installation. T2 - Recent Advances in Glass and Ceramics Conservation 2016, ICOM-CC Working Group “Glass and Ceramics” Interim Meeting CY - The Eugeniusz Geppert Academy of Art and Design, Wrocław, Poland DA - 25.05.2016 KW - weathering KW - stained glass KW - protective glazing KW - glass dosimeters KW - outdoor pollutants PY - 2016 SN - 978-83-64419-80-5 SP - 53 EP - 62 PB - International Council of Museums - Committee for Conservation (ICOM-CC) CY - Paris, France AN - OPUS4-36678 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, Matthias T1 - Emissionen aus Baustoffen in die Luft - Untersuchungen für gesundes Wohnen N2 - Vorstellung der Vorgehensweise bei der Bestimmung und Bewertung von Baustoffemissionen in die Innenraumluft mit Beispiel aus einem laufenden Forschungsprojekt. T2 - Die nachwachsende Stadt - Natürlich gesund bauen; Symposium im Rahmen des Tages der Architektur 2016 CY - Berlin, Germany DA - 25.06.2016 KW - Materialemission KW - VOC KW - Innenraumlufthygiene PY - 2016 AN - OPUS4-36681 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Peplinski, Burkhard A1 - Adamczyk, Burkart A1 - Meyer, Christian A1 - Krüger, Oliver A1 - Scharf, Holger A1 - Reinsch, Stefan A1 - Ostermann, Markus A1 - Nofz, Marianne A1 - Jäger, Christian A1 - Adam, Christian A1 - Emmerling, Franziska T1 - Nanocrystalline and stacking-disordered beta-cristobalite AlPO4 stabilized at room temperature: synthesis and X-ray powder diffraction data N2 - X-ray powder diffraction (XRD) patterns of the high-temperature (HT) cristobalite form of SiO2 and its isoelectronic AlPO4 analogue are essentially influenced by the dynamic disorder of these crystal structures. The nature of this disorder and of the phase transition between the α- and β-form has been the subject of intensive research during the last four decades [1]. By 1989 it became possible to stabilize the HT-form of cristobalite SiO2 at room temperature in laboratory and engineering ceramic industries by applying solid solution forming techniques [2]. However, for the HT-form of cristobalite AlPO4 nothing similar has been known until 2014 when it was discovered that nanocrystalline and stacking-disordered β-cristobalite AlPO4 is the major component of the fly ash of a large incineration facility operated by the waste water treatment authorities of Frankfurt/M. [3]. Previous comprehensive investigations of this fly ash failed to interpret its complex XRD pattern – presumably mainly due to the lack of a matching experimental digital pattern in the Powder Diffraction Database. The present paper reports on a synthesis route that facilitates the crystallization of nanocrystalline and stacking-disordered β-cristobalite AlPO4 that is free of crystalline impurity phases and long-term stable at ambient. Its room temperature XRD pattern is presented with parameters traced back to certified reference materials. [1] Yuan F. and Huang L., Phys. Rev, B, 2012, 85, 134114. [2] Perrotta J.A., Grubbs D.K., Martin E.S., Dando N.R., McKinstry H.A. and Huang C.-Y., J. Am. Ceram. Soc., 1989, 72, 441. [3] Peplinski B., Adam C., Adamczyk B., Müller R., Michaelis M., Krahl Th. and Emmerling F., Powder Diffraction Journal, 2015, 30, 2, Supp. 1, S31. T2 - 15. European Powder Diffraction Conference (EPDIC15) CY - Bari, Italy DA - 12. June 2016 KW - Stabilization of HT-structures at room temperature KW - β-cristobalite structure type KW - Databases PY - 2016 AN - OPUS4-36727 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grunewald, Thomas T1 - Nichtelektrischer Explosionsschutz - mechanisch erzeugte Funken als Zündquelle N2 - Bei Geräten und Maschinen zur bestimmungsgemäßen Verwendung in explosionsgefährdeten Bereichen muss in der europäischen Union eine Zündgefahrenbewertung durchgeführt werden. Dabei müssen unter anderem die Gefahren von nichtelektrischen Zündquellen betrachtet werden, zu denen auch die mechanischen Schlagvorgänge gehören. Bei Schlagvorgängen kommt es infolge des Zusammenstoßes zweier Werkstücke zu einer Umwandlung der kinetischen Energie. Dabei erhöht sich die Temperatur der Werkstoffe an der Kontaktstelle und es kommt unter Umständen zu einem Abtrennvorgang kleiner Partikel erhöhter Temperatur. Sowohl die heißen Kontaktstellen als auch die abgetrennten Partikel können eine wirksame Zündquelle für ein explosionsfähiges Gasgemisch darstellen. Zur Festlegung von Grenzwerten wurden in der Norm EN 13463-1:2009 die Gasgemische anhand ihrer Explosionsgruppe klassifiziert und zu jeder Gruppe die maximale Energie des Schlagvorgangs festgelegt, unter derer die Entstehung einer wirksamen Zündquelle als unwahrscheinlich angenommen werden kann. T2 - Ausbildung zum Explosionsschutzbeauftragten (Veranst.-Nr. H050-07-055-6) CY - Haus der Technik (HdT) - Außeninstitut der RWTH Aachen, Essen, Germany DA - 14.06.2016 KW - Funken KW - Mechanisch erzeugte Funken KW - Schlagfunken KW - Nichtelektrische Funken KW - Nichtelektrischer Explosionsschutz PY - 2016 AN - OPUS4-36728 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Neubert, Sebastian A1 - Pittner, Andreas A1 - Rethmeier, Michael T1 - Experimental determination of TRIP parameter K for mild- and high strength low alloy steels and a super martensitic filler material JF - SpringerOpen N2 - A combined experimental numerical approach is applied to determine the transformation induced plasticity (TRIP)-parameter K for different strength low-alloy steels of grade S355J2+N and S960QL as well as the super martensitic filler CN13-4-IG containing 13 wt% chromium and 4 wt% nickel. The thermo-physical analyses were conducted using a Gleeble® 3500 facility. The thermal histories of the specimens to be tested were extracted from corresponding simulations of a real gas metal arc weldment. In contrast to common TRIP-experiments which are based on complex specimens a simple flat specimen was utilized together with an engineering evaluation method. The evaluation method was validated with literature values for the TRIP-parameter. It could be shown that the proposed approach enables a correct description of the TRIP behavior. KW - Transformation induced plasticity (TRIP) KW - Phase transformation KW - High-strength low-alloy steel KW - Super martensitic filler material KW - Thermo physical simulation KW - Gleeble experiments PY - 2016 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-367297 DO - https://doi.org/10.1186/s40064-016-2474-0 VL - 5 IS - 575 SP - Paper 754, 1 EP - 16 PB - SpringerPlus AN - OPUS4-36729 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Braun, Ulrike A1 - Dümichen, Erik A1 - Eisentraut, Paul A1 - Barthel, Anne-Kathrin A1 - Bannick, Claus Gerhard T1 - Mikroplastik: Ein Material oder ein Problem? N2 - Durch den stetig steigenden Einsatz von Plastikprodukten sind unerwünschte Kunststofffunde in verschiedenen Umweltmatrices mittlerweile allgegenwärtig. Bereits seit Jahren werden die Funde in aquatischen Bereich kommentiert, mittlerweile erfahren auch terrestrische Kompartimente erhöhte Aufmerksamkeit. Besonderes Interesse erfahren Kunststoffpartikel von einer Größe kleiner 5 mm, sogenannte Mikroplastik (MP) Partikel. T2 - Kunststofftechnisches Kolloquium CY - Chemnitz, Germany DA - 10.05.2016 KW - Mikroplastik KW - Polymere PY - 2016 AN - OPUS4-36757 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Burkert, Andreas A1 - Fischer, Joachim A1 - Lehmann, Jens A1 - Müller, Thoralf T1 - Korrosionsbeständigkeit nichtrostender Stähle an der Atmosphäre T2 - Merkblatt der Informationsstelle Edelstahl Rostfrei N2 - Über das Korrosionsverhalten nichtrostender Stähle bei atmosphärischer Beanspruchung liegen umfangreiche Erfahrungen aus jahrzehntelangen praktischen Anwendungen weltweit vor. Systematische Auslagerungsversuche unter spezifischen Umgebungsbedingungen ergänzen diese Erfahrungen. Die daraus gewonnenen Daten erlauben die beanspruchungsgerechte Werkstoffauswahl. Unter vielen atmosphärischen Bedingungen sind die nichtrostenden Stähle bei freier Bewitterung, auch unter langzeit- oder dauerfeuchten Bedingungen vollständig korrosionsbeständig. Die Auswahl der nichtrostenden Stähle muss den jeweiligen Einsatzbedingungen angepasst werden, um in jedem Fall sicherzustellen, dass der passive Zustand aufrechterhalten bzw. eine erneute Passivierung unter den Einsatzbedingungen möglich ist. Störungen der Passivschichtausbildung führen zu verminderter Korrosionsbeständigkeit mit den für nichtrostende Stähle typischen örtlichen Korrosionserscheinungen. Das Merkblatt gibt Hinweise zur Werkstoffauswahl, zur Oberflächenausführung, zur Konstruktion sowie zu Verarbeitung, Nachbehandlung und Reinigung. KW - Verarbeitung KW - Werkstoffauswahl KW - Oberflächenausführung PY - 2016 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-367612 UR - http://www.edelstahl-rostfrei.de/page.asp?pageID=1583 VL - 828 SP - 1 EP - 12 PB - Informationsstelle Edelstahl Rostfrei CY - Düsseldorf ET - 3. Auflage AN - OPUS4-36761 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Fischer, Joachim A1 - Lehmann, Jens A1 - Müller, Thoralf A1 - Burkert, Andreas T1 - Korrosionsbeständigkeit nichtrostender Stähle an der Atmosphäre JF - Stahlmarkt N2 - Über das Korrosionsverhalten nichtrostender Stähle bei atmosphärischer Beanspruchung liegen umfangreiche Erfahrungen aus jahrzehntelangen praktischen Anwendungen weltweit vor. Systematische Auslagerungsversuche unter spezifischen Umgebungsbedingungen ergänzen diese Erfahrungen. Die daraus gewonnenen Daten erlauben die beanspruchungsgerechte Werkstoffauswahl. Unter vielen atmosphärischen Bedingungen sind die nichtrostenden Stähle bei freier Bewitterung, auch unter langzeit- oder dauerfeuchten Bedingungen vollständig korrosionsbeständig. Die Auswahl der nichtrostenden Stähle muss den jeweiligen Einsatzbedingungen angepasst werden, um in jedem Fall sicherzustellen, dass der passive Zustand aufrechterhalten bzw. eine erneute Passivierung unter den Einsatzbedingungen möglich ist. Störungen der Passivschichtausbildung führen zu verminderter Korrosionsbeständigkeit mit den für nichtrostende Stähle typischen örtlichen Korrosionserscheinungen. Das Merkblatt gibt Hinweise zur Werkstoffauswahl, zur Oberflächenausführung, zur Konstruktion sowie zu Verarbeitung, Nachbehandlung und Reinigung. KW - Verarbeitung KW - Oberflächenausführung KW - Werkstoffauswahl PY - 2016 SN - 0178-6571 IS - 6 SP - 52 EP - 54 PB - Montan- und Wirtschaftsverlag GmbH CY - Düsseldorf AN - OPUS4-36763 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fischer, Franziska A1 - Heidrich, Adrian A1 - Greiser, Sebastian A1 - Rademann, K. A1 - Emmerling, Franziska T1 - Polymorphism of mechanochemically synthesized Cocrystals: an in situ study N2 - In situ investigations using PXRD coupled with Raman spectroscopy permit the evaluation of the formation pathways of milling reactions. The liquid-assisted grinding cocrystallisation of theophylline with benzamide leading to polymorphic compounds was investigated. The dipole moment of the solvent used in the synthesis determines the structure of the polymorphic product. A detailed investigation allows determining the kinetically and thermodynamically favored product. In situ observations of the formation pathway during the grinding process of both polymorphs show that the thermodynamically favored cocrystal is formed in a two-step mechanism with the kinetic cocrystal as intermediate. The evaluation of the mechanochemical formation pathways reveals the importance of in situ investigations for an in depth understanding of mechanochemical synthesis mechanisms. Our study demonstrates that the choice of the solvent in the LAG synthesis is decisive for the controlled formation of a desired polymorphic final product. T2 - CGOM/ BACG 47th Annual British Association of Crystal Growth Conference CY - Leeds, UK DA - 28.06.2016 KW - Cocrystal KW - Mechanochemistry KW - Milling PY - 2016 AN - OPUS4-36764 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schaupp, Thomas A1 - Griesche, Axel A1 - Müller, Bernd R. A1 - Kannengießer, Thomas A1 - Bruno, Giovanni A1 - Laquai, René T1 - 3D Charakterisierung wasserstoffunterstüzter Risse in Stahl mittels Synchrotron-Refraktions-CT N2 - Die Fehlertoleranz moderner hochfester Stähle gegenüber Prozessfehlern beim Fügen nimmt stetig ab und erfordert eine immer kritischere Beurteilung der Ergebnisse aus den vorhandenen Prüfverfahren. Deren Aussagekraft ist häufig zu gering und daher muss zum einen das wissenschaftliche Verständnis der Mikrokaltriss-Entstehung in diesen Stählen vertieft werden und zum anderen müssen die Prüfmethoden und Bewertungskriterien angepasst werden. Dies erfordert ein besseres Verständnis insbesondere der Kopplung von Eigenspannungen, Wasserstoffgehalten und der Wirkung äußerer Kräfte auf die Rissentstehung und das Risswachstum. Erstmals soll mittels 3D-Synchrotron-Refraktions-Topographie an der BAMline am BESSY die Rissentstehung in mit Wasserstoff beladenen Zugproben charakterisiert werden. Diese Kenntnisse sollen in weiteren Untersuchungen auf Schweißnähte übertragen werden. T2 - MDDK – Master-, Diplomanden- und Doktorandenkolloquium CY - Universität Magdeburg, Germany DA - 23.06.2016 KW - Duplexstahl KW - Wasserstoffunterstützte Rissbildung KW - Computertomographie KW - Synchrotron-Refraktion PY - 2016 AN - OPUS4-36733 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Woydt, Mathias T1 - Tribological profile of hydraulic oils by using SRV N2 - Hydraulic oils are well established formulations developed around the pump test. Requirements for energy efficiency and also environmentally acceptable properties increased the demand for development. In the same time, system pressure and the used of servo-hydraulic vanes increased bringing specific formulations and materials to their limit. The vane pump is a key component in hydraulic systems and many other tribosystems in hydraulic circuits operate under different tribological operating conditions. The concept for ranking of hydraulic oils consists in using existing SRV-based ASTM test methods for evaluation of friction, wear and extreme pressure properties: D6425, friction and wear of oils (homologue to DIN 51834-2), D7421, extreme pressure properties of oils and D7755, wear volumes of ball and disks (homologue to DIN 51834-3. The tribological properties are assessed under the regime of mixed/boundary lubrication The SRV-based concept of tribological profile generates the wear volumes on two triboelements (specimen) and the extreme pressure properties as well as the evolution of friction in the wear and extreme pressure load step test. Thus, the benchmark and validation of hydraulic oils bear on a wider range of tribological properties. Round robin test results using the aforementioned testing concept will be shown. Another outcome is tribological set limits for inclusion in hydrau¬lic oil speci¬fications. T2 - Workshop on Tribological Testing of Components Using the SRV Test Machine CY - Bellevue, WA, USA DA - 30.06.2016 KW - Tribology KW - Hydraulic oils KW - SRV KW - ASTM test method KW - Friction KW - Wear PY - 2016 AN - OPUS4-36734 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Patzer, G. A1 - Ebrecht, J. A1 - Woydt, Mathias T1 - New interpretation approaches for seizure load tests on the translatory oscillation tribometer (SRV) N2 - When looking in detail at analyses of the tribological load-carrying capacity of high-performance lubricants, it becomes apparent that the stop of the machine of an exclusive evaluation of the development of the coefficient of friction cannot provide any sufficient criteria for determining the occurrence of adhesive failure. This is due on the one hand to the increasing complexity of lubricant formulae and sophisticated additive packages, and on the other hand to the increasing frictional power capacity of modern drive and control concepts in the design of tribometers. For this reason, it is urgently needed to examine the adhesive processes and their detection in more detail with the help of appropriate tribological values and criteria. The evolution of the friction can be coupled with the stroke, contact resistant and/or noise emission. Besides from new criteria for adhesive failure, which were compiled by the work group for the relevant ISO, DIN and ASTM standards, this contribution discusses the inclusion of additional parameters. Among other things, it provides guidance on what evidence the continuous recording of the original coefficient of friction and position signals, the electrical contact resistance, temperature, noise emission, frictional power input of the machine and further derived parameters help to identify adhesive failures or events. T2 - Workshop on Tribological Testing of Components Using the SRV Test Machine CY - Bellevue, WA, USA DA - 30.06.2016 KW - Tribology KW - Friction KW - Translatory oscillation tribometer KW - Standards PY - 2016 AN - OPUS4-36735 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilrich, Cordula T1 - Aktuelles zu Rechtsvorschriften in der chemischen Sicherheitstechnik T2 - Tagungsband zum 14. Kolloquium zur chemischen und physikalischen Sicherheitstechnik N2 - Im Chemikalienrecht ergeben sich laufend Änderungen durch die regelmäßige Überar-beitung des UN-GHS. Konsequenzen hat dies auch für andere Vorschriften, die auf Einstufungen von gefährlichen Stoffen Bezug nehmen. Aber auch andere Vorschriften und Regelwerke unterliegen Änderungen durch Anpassungen an den Stand der Tech-nik. In diesem Beitrag werden für die chemische Sicherheitstechnik wichtige aktuelle Änderungen im Chemikalienrecht und nationalen Arbeitsschutzvorschriften vorgestellt. Die 6. überarbeitete Fassung des GHS von 2015 enthält eine neue Gefahrenkategorie zur Einstufung von pyrophoren Gasen und eine neue Gefahrenklasse zur Einstufung von desensibilisierten explosiven Stoffen. Außerdem wurden Anforderungen an das Si-cherheitsdatenblatt bezüglich der physikalisch-chemischen Eigenschaften neu gefasst und um Informationen für die Ersteller von Sicherheitsdatenblättern ergänzt. Die 7. überarbeitete Fassung des GHS, die zurzeit in Arbeit ist und Anfang 2017 erschei-nen wird, wird voraussichtlich neue Kriterien und eine geänderte Einteilung für ent-zündbare Gase beinhalten sowie einen neuen Anhang zur Staubexplosionsgefahren. Bei den nationalen Arbeitsschutzvorschriften haben sich Änderungen anlässlich der Verschiebung der Vorschriften zum betrieblichen Explosionsschutz von der Betriebssi-cherheitsverordnung in die Gefahrstoffverordnung ergeben. Im Nachgang werden auch die technischen Regeln zum Explosionsschutz überabeitet. Die technischen Re-geln für Tätigkeiten mit Gasen sind um Regelungen zu Acetylen ergänzt worden. Wei-tere Ergänzungen zu Füllanlagen für ortsfeste Druckanlagen für Gase und zu Flüssig-gas liegen gegenwärtig den zuständigen Ausschüssen zur Verabschiedung vor. T2 - 14. BAM-PTB-Kolloquium CY - Berlin, Germany DA - 14.06.2016 KW - Chemikalienrecht KW - Arbeitsschutzvorschriften KW - Sicherheitsdatenblatt KW - Einstufung gefährlicher Stoffe KW - Technische Regeln Gase KW - UN-GHS PY - 2016 SN - 978-3-9817853-5-7 SN - 0938-5533 SP - 37 AN - OPUS4-36736 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -