TY - CONF A1 - Maurer, G. T1 - High-pressure gas solubility in mixtures with one compound being an „alternative“ solvent N2 - The term „Alternative Solvents“ often refers to ionic liquids (ILs), mainly to distinguish these substances from traditional (i.e., molecular) solvents. In applications, any „alternative“ is required to perform better than something that is proven and tested. To bring ILs into practical use, availability and costs are the fundamental points to be addressed. There are two ways to proceed: ▬ tailoring a molecule, implanting the expected characteristics advantage: optimization of the targeted performance possible risks: outcome not always foreseeable, costly and time-intensive (“trial and error“) ▬ to target on mixtures of well-characterized ILs with molecular solvents advantage: substance characteristics are known, less costly, less time-consuming, mixture composition another tunable parameter risks: the same but with less impact For the basic engineering of technical processes, knowledge of phase equilibria, particularly of mixtures, over a broad (p,T) range is mandatory. This contribution reports on recent experimental results from our laboratory: ▬ the solubility of CO2 in a mixture of water and [bmim][CH3SO4] ▬ the solubility of CO2 in a mixture of methanol and [bmim][PF6] T2 - EUCHEM 2014 5th Conference on Molten Salts and Ionic Liquids CY - Tallinn, Estonia DA - 06.07.2014 KW - Ionic liquids KW - Gas solubility KW - Henry's constant PY - 2014 AN - OPUS4-35944 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Dmitriev, A. I. A1 - Österle, Werner T1 - Modelling the sliding behaviour of tribofilms forming during automotive braking: impact of loading parameters and property range of constituents N2 - The impact of pressure, sliding velocity and property variation of constituents on the sliding behaviour of a model tribofilm was studied with the method of movable cellular automata (MCA). Whereas a clear pressure dependency of the coefficient of friction (COF) was always observed and could be correlated with the structure formation in terms of varying thickness of a mechanically mixed layer, the impact of the other parameters was either negligible or rather weak. Only if a brittle-to-ductile Transition of the oxide-based tribofilm was assumed, a significant decrease in the COF level was predicted. Temperature-dependent property changes can be neglected during MCA modelling, unless this transition takes place. For magnetite-based tribofilms, the transition temperature is beyond 800 °C, i.e. a temperature leading to fading effects during braking anyway. Thus, it could be concluded that, except for very severe braking conditions, sliding simulations with the MCA method yield meaningful results without considering temperature-dependent mechanical properties. KW - Tribofilm KW - Sliding behaviour KW - Friction KW - Movable cellular automata KW - Mechanically mixed layer PY - 2014 DO - https://doi.org/10.1007/s11249-013-0274-z SN - 1023-8883 SN - 1573-2711 VL - 53 IS - 1 SP - 337 EP - 351 PB - Springer AN - OPUS4-38548 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Vasilic, Ksenija A1 - Geiker, M. A1 - Hattel, J. A1 - Martinie, L. A1 - Martys, N. A1 - Roussel, N. A1 - Spangenberg, J. ED - Roussel, N. ED - Gram, A. T1 - Advanced methods and future perspectives N2 - The one-phase methods described in Chapter 2 were shown to be able to predict casting to some extent, but could not depict segregation, sedimentation and blockage occurring during flow. On the other hand, the distinct element methods described in Chapter 3 did not take into account the presence of two phases in the system and describes concrete as distinct elements interacting through more or less complex laws. A reliable numerical model of a multiphase material behaviour shall take into account both phases (solid and liquid). From the numerical point of view, concrete flow shall be seen therefore as the free surface flow of a highly-concentrated suspension of rigid grains. KW - SCC KW - Numerical simulation PY - 2014 SN - 978-94-017-8883-0 DO - https://doi.org/10.1007/978-94-017-8884-7_5 VL - 15 SP - 125 EP - 146 PB - Springer Netherlands AN - OPUS4-37443 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Griesche, Axel T1 - Hydrogen in Iron visualized in 3D by neutron tomography N2 - Presented are neutron tomographies on hydrogen charged iron samples. T2 - RACIRI Summer School 2015 CY - Sellin, Rügen, Germany DA - 22.08.2015 KW - Tomographie KW - Wasserstoff KW - Neutronen KW - Hydrogen KW - Neutron KW - Tomography PY - 2014 AN - OPUS4-44838 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pfretzschner, Beate T1 - Hydrogen in blistered iron visualized in 3D by neutron tomography N2 - Presented are neutron tomographies on hydrogen charged iron samples. T2 - RACIRI Summerschool CY - Sellin, Germany DA - 22.08.2015 KW - Eisen KW - Neutronenradiographie KW - Wasserstoff PY - 2014 AN - OPUS4-47786 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schartel, Bernhard ED - D'Amore, A. ED - Acierno, Domenico ED - Grassia, L. T1 - Nanotechnology finding its way into flame retardancy N2 - Nanotechnology is one of the key technologies of the 21st century. The exploitation of 'new' effects that arise from materials structured on the nano-scale has also been proposed successfully for flame retardancy of polymers since the end of the 90s. Of all of the approaches these include, at this time the use of nanocomposites offers the best potential for industrial application, also some other ideas are sketched, such as using electrospun nanofibers mats or layer-by-layer deposits as protection coatings, as well as sub-micrometer multilayer coatings as effective IR-mirrors. The general phenomena, inducing a flow limit in the pyrolysing melt and changing the fire residue, are identified in nanocomposites. Key experiments are performed such as quasi online investigation of the protection layer formation to understand what is going on in detail. The flame retardancy mechanisms are discussed and their impact on fire behaviour quantified. With the latter, the presentation pushes forward the state of the art. For instance, the heat shielding is experimentally quantified for a layered silicate epoxy resin nanocomposite proving that it is the only import mechanism controlling the reduction in peak heat release rate in the investigated system for different irradiations. The flame retardancy performance is assessed comprehensively illuminating not only the strengths but also the weak points of the concepts. Guidelines for materials development are deduced and discussed. Apart from inorganic fillers (layered silicate, boehmite, etc.) not only carbon nanoobjects such as multiwall carbon nanotubes, multilayer graphene and graphene are investigated, but also nanoparticles that are more reactive and harbor the potential for more beneficial interactions with the polymer matrix. T2 - Times of polymers (TOP) and composites 2014 - 7th international conference on times of polymers (TOP) and composites CY - Ischia, Italy DA - 22.06.2014 KW - Nanotechnology KW - Flame retardancy KW - Nanocomposites KW - Fire behavior KW - Layered silicate KW - Graphene KW - Nanotubes KW - Nanofibers KW - Flammability KW - Cone calorimeter PY - 2014 SN - 978-0-7354-1233-0 DO - https://doi.org/10.1063/1.4876766 SN - 0094-243X N1 - Serientitel: AIP conference proceedings – Series title: AIP conference proceedings VL - 1599 SP - 14 EP - 17 PB - AIP Publishing CY - Melville, New York AN - OPUS4-30994 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Madia, Mauro A1 - Zerbst, Uwe A1 - Beier, H.T. T1 - A model for the determination of the fatigue life in technical alloys containing large and small defects N2 - The determination of the fatigue life in technical alloys containing large and small defects must rely on a propagation model which accounts for short and long crack growth. Recently an analytical model which incorporates propagation in the short crack regime and plastic correction for the crack driving force has been presented by two of the authors. This work is intended to show further validation of the model, taking into account data sets for different materials with different testing conditions. Despite the assumptions about missing parameters, the value of which had to be taken from the literature, the predictions showed a fairly good approximation of the fatigue lives. A possible interpretation of the results in terms of multiple crack initiation and propagation at higher loads is proposed. T2 - EFC20 - 20th European conference on fracture CY - Trondheim, Norway DA - 30.06.2014 KW - Fatigue strength KW - Crack propagation KW - Short cracks PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-311961 DO - https://doi.org/10.1016/j.mspro.2014.06.082 SN - 2211-8128 VL - 3 SP - 493 EP - 498 PB - Curran CY - Red Hook, NY, USA AN - OPUS4-31196 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Trappe, Volker A1 - Basan, Ricardo A1 - Grasse, Fabian ED - Paris, Federico T1 - Stiffness and fracture of shear loaded laminates with unidirectional and biaxial fibre orientation investigated with a picture frame test N2 - Fibre Reinforced Plastics (e.g. CFRP, GFRP) characteristically show nonlinear stress-strain behaviour due to intralaminar shear loading. The determination of the in-plane shear stiffness and strength for this class of material is difficult and common test standards and methods of analysis are partially inaccurate. The identification of the in-plane shear properties was made with an especial designed “picture frame test device” which enables shear loading up to 950N/mm. Therefore the strength limit can be reached at specimens with adequate thickness and a high safety factor against buckling. Due to the chosen design the maximum of the shear loading and the final failure occur in the centre of the specimen. The experiments match with the numerical analysis. T2 - ECCM16 - 16TH EUROPEAN CONFERENCE ON COMPOSITE MATERIALS CY - Seville, Spain DA - 22.06.2014 KW - Picture frame test KW - Fibre reinforced plastics (FRP) KW - Shear strength and stiffness KW - In-situ effect PY - 2014 SN - 978-84-616-9798-4 VL - 2014 SP - ID0263 - 1 EP - 8 PB - ECCM CY - Sevilla AN - OPUS4-37617 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Winkelmann, Aimo T1 - Improved analysis of EBSD patterns N2 - The presentation demonstrates how crystal structures can be derived from EBSD patterns. T2 - EBSD Meeting CY - London, UK DA - 31.03.2014 KW - Electron backscatter diffraction KW - Kikuchi pattern KW - Crystal structure analysis PY - 2014 AN - OPUS4-37893 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nolze, Gert T1 - Computational Advances N2 - The EBSD signal provides more information than the used Kikuchi pattern. The presentation discusses several parts of the detected signal and how they can be interpreted. T2 - EBSD 2014 CY - Pittsburgh, Pennsylvania, USA DA - 17.06.2014 KW - Electron backscatter diffraction KW - Simulation KW - Kikuchi pattern KW - Magnetite KW - Maghemite KW - Hematite PY - 2014 AN - OPUS4-37899 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -