TY - CONF A1 - Trappe, Volker T1 - Composite materials - focus polymer matrix composites (PMC) N2 - Lecture about polymer matrix composites as part of the first trainings event GW4SHM, properties, production, basic theory, testing. T2 - 1. Training GW4SHM-Project CY - BAM, Berlin, Germany DA - 23.11.2020 KW - Polymer matrix composites KW - Composite testing KW - NDT PY - 2020 AN - OPUS4-51868 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bertovic, Marija T1 - The first insights into the human factors in the inspection of railway axles N2 - The field of human factors has been concerned with prevention of organisational accidents and the maintaining of the highest safety standards in organisations with high hazard potential since its beginnings. Whereas it is known that human error has contributed to some well-known accidents and events in various safety-critical applications, as well as in railway, and that human factors have an impact on how reliable our non-destructive inspections are, very little has been done so far to address human factors, especially in the railway sector. The first steps in addressing human factors in the inspection of railway axles has been carried out by analysing the results of manual ultrasonic inspection of the railway axles during requalification in the education centre of the German Society for Non-Destructive Testing (DGZfP). In addition to the inspection, 160 participants were asked to fill out a questionnaire with the aim of identifying potential factors influencing their performance. The results showed that no correlation between the possible influencing factors (i.e. experience, level of qualification, satisfaction with the conditions during the re-qualification as well as in the daily practice and mental workload) and the inspection results. The explanation for this result was found in the fact that questionnaires can be used only to identify indirectly influencing factors. The only way to identify directly influencing factors and establish cause-effect relationships is by experimental study. The limitation of this study was the inability to influence the participants in any way during the requalification examination. Another angle used to identify potential influencing factors was the use of human-oriented Failure Modes and Effects Analysis. Carried out together with 4 experts from the field practice, two lecturers and two scientists, this analysis provided with an extensive list of possible failures, their causes, consequences and possible barriers. The largest benefits for the reliability of manual ultrasonic railway axle inspections in the practice can be found in attending to the organisational aspects of the inspection (e.g. processes, procedures, communication, education, supervision etc.). T2 - ESIS TC24 workshop "Integrity of Railway Structures" CY - Leoben, Austria DA - 24.10.2016 KW - Human factors KW - Reliability KW - NDT KW - Railway axle PY - 2016 AN - OPUS4-38251 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pavlovic, Mato T1 - Investigations to Introduce the Probability of Detection Method for Ultrasonic Inspection of Hollow Axles at Deutsche Bahn N2 - Reliability investigation of the mechanised ultrasonic inspection system used to inspect hollow railway axles. T2 - ESIS TC24 Workshop "Integrity of Railway Structures" CY - Leoben, Austria DA - 24.10.2016 KW - POD KW - Ultrasonic KW - Reliability KW - NDT PY - 2016 AN - OPUS4-38460 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bertovic, Marija T1 - A human factors perspective on the use of automated aids in the evaluation of NDT data N2 - In comparison to manual NDT methods, mechanized NDT is considered to be more reliable for a number of reasons, one of which being that the role of the inspectors and, therewith, the potential for human error, have been reduced. However, human-automation interaction research suggests that in spite of its numerous benefits, automation can lead to new yet unknown risks. One of those risks is inappropriate reliance on automation, which can result in automation misuse and disuse. The aim of this study was to investigate the potential inappropriate use of automation (specifically - the automated aids) in NDT addressing therewith the prevalent belief in the high reliability of automation held by the NDT community. To address this issue, 70 NDT trainees were asked to control the results of an eddy current data evaluation, allegedly provided by an automated aid, i.e. indication detection and sizing software. Seven errors were implemented into the task and it was measured to what extent the participants agreed with the aid. The results revealed signs of both misuse (agreeing with the aid even though it is incorrect) and disuse (disagreeing with the aid even though it is correct) of the aid that can affect the reliability with which inspections are carried out. Whereas misuse could be explained by a lower propensity to take risks and by a decreased verification behaviour-possibly due to bias towards automation and complacent behaviour-, disuse was assigned to problems in establishing the sizing criterion or to general difficulties in sizing. The implications of these results for the NDT praxis including suggestions for the decrease of automation bias are discussed. T2 - 42nd Annual Review of Progress in Quantitative Nondestructive Evaluation CY - Minneapolis, MN, USA DA - 26.07.2015 KW - Non-Destructive Testing KW - Human Factors KW - NDT KW - Automation Bias PY - 2016 UR - http://scitation.aip.org/content/aip/proceeding/aipcp/10.1063/1.4940449 DO - https://doi.org/10.1063/1.4940449 VL - 1706 SP - 020003-1 EP - 020003-16 PB - Amer institute physics CY - Melville, NY, USA AN - OPUS4-36561 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, Christina A1 - Bertovic, Marija A1 - Kanzler, Daniel A1 - Ronneteg, U. T1 - Conclusions of the 6th European American workshop on reliability of NDE N2 - The principles of Open Space Technology (OST) were again applied to discuss burning issues in the field of NDE reliability. The results of the discussions among NDE professionals concerning new reliability methods, human factors and integrated solutions will be presented. T2 - 42nd Annual Review of Progress in Quantitative Nondestructive Evaluation CY - Minneapolis, Minnesota, USA DA - 26.07.20155 KW - NDT KW - Reliability KW - Probability of detection KW - Human factors KW - POD PY - 2016 SN - 978-0-7354-1353-5 DO - https://doi.org/10.1063/1.4940452 SN - 0094-243X VL - 1706 SP - 020006-1 EP - 020006-9 PB - AIP Publishing AN - OPUS4-36637 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pavlovic, Mato T1 - Reliability Analysis of the Phased-Array Ultrasonic System used for the Inspection of Friction Stir Welds of Copper Canisters N2 - The canister for the permanent storage of spent nuclear fuel used by SKB in Sweden consists of a cast iron insert surrounded by a five centimetre thick shell of copper. It is a safety critical component and in order to secure long-term structural integrity non-destructive methods are used to inspect 100% of the volume of each canister, before it is disposed of in the repository. One of the critical components that requires inspection is a sealing weld, joining the copper tube and the lid. The friction stir weld is inspected using an ultrasonic phased array system. The area of the weld is inspected with several inspection channels with different angles and varying coverage. To make sure that no defects that might occur in the weld are overseen, the reliability of the inspection must be quantified. The reliability of NDT is usually quantified with the probability of detection curves. The influence of the parameters that might influence the POD of the flaws in the weld is investigated analysing the experimental results, as well as with a help of a numerical simulation of the inspection. T2 - Proceedings of the 19th World Conference on Nondestructive Testing CY - Munich, Germany DA - 13.06.2016 KW - Ultrasonic KW - Copper KW - NDT KW - FSW KW - JLH KW - Weld KW - POD KW - Reliability PY - 2016 AN - OPUS4-36703 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pavlovic, Mato T1 - Achieving a more comprehensive POD using both simulation and measurements N2 - Today, it is an established fact that the capability of the non-destructive testing (NDT) to find flaws can be properly addressed only in terms of probability of detection (POD). The probabilistic, signal-response model, introduced in 1980s, was developed with experimental observation of eddy-current inspections of flat plate samples, containing surface breaking cracks. A linearity between the peak voltage measured by the testing system, and the crack depth was observed. The influence of the crack depth was therefore seen as the major influencing factor for the POD, whereas other factors merely caused the variability in the measurement. This model has proven itself valid for those inspection cases where there is only one main influencing factor on the POD (usually the flaw size) and other factors have a lesser influence. But with increasing requirements to quantify the capability of NDT systems in complex inspection situations, where several factors have a major influence on the POD, it has become clear that the applicability of this simple model has reached its limits. In disregard to its limitations, this model is regularly applied to those situations in which its fundamental assumptions are invalid, forcing evaluators and NDT researchers into attempts to fit the data to an unsuitable model, instead of fitting an appropriate model to the data. The multiparameter POD model, developed in the early 2010s, enables more factors that influence detection to be simultaneously analysed, making the POD a function of multiple factors. The model is based on the inspection’s physical model, to describe the influence of different factors on the response signal. Measurement variability is obtained from the experiment. Using this model assisted determination of the POD, the necessary number of flaws for evaluation is reduced and a more comprehensive understanding of the inspection is obtained. Several examples of the successful application of the multi-parameter POD model in different fields will be presented. T2 - 7th European-American Workshop on Reliability of NDE CY - Potsdam, Germany DA - 04.09.2017 KW - POD KW - Multi-parameter KW - Reliability KW - NDT PY - 2017 AN - OPUS4-42078 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Junker, Birgit A1 - Stamm, Michael T1 - No downtime thermographic rotor blade inspection N2 - In this presentation, the KI-VISIR Reference Dataset, created by the Bundesanstalt für Materialforschung und -prüfung (BAM) will be discussed. It includes thermographic and visual inspection data of 30 operational wind turbines. This dataset aims to support the maintenance and inspection of wind turbines, which are increasingly being built across Germany and Europe. The data is publicly available and helps in the development of digital methods for damage classification and inspection. T2 - AMI Wind Turbine Blades CY - Düsseldorf, Germany DA - 10.12.2024 KW - Thermography KW - Wind Turbine Blades KW - AI KW - KI-VISIR KW - NDT PY - 2024 AN - OPUS4-62498 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stamm, Michael T1 - Damage detection of wind turbine blades with thermographic inspection and AI-based classification N2 - In this presentation, the possibilities, limitations and challenges of thermographic rotor blade inspection will be discussed. Among other things, the data from the KI-VISIR reference data set will be discussed. This data was also used to train an AI-based image recognition system. T2 - WindEurope Technology Workshop 2024 CY - Dublin, Ireland DA - 10.06.2024 KW - Thermography KW - Wind Turbine Blades KW - AI KW - KI-VISIR KW - NDT PY - 2024 AN - OPUS4-62499 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ratkovac, Mirjana A1 - Gerards-Wünsche, Paul A1 - Thiele, Marc A1 - Brackrock, Daniel A1 - Stamm, Michael T1 - Detection and monitoring of the fatigue crack growth on welds – Application-oriented use of NDT methods N2 - Early detection of fatigue cracks and accurate measurements of the crack growth play an important role in the maintenance and repair strategies of steel structures exposed to cyclic loads during their service life. Observation of welded connections is especially of high relevance due to their higher susceptibility to fatigue damage. The aim of this contribution was to monitor fatigue crack growth in thick welded specimens during fatigue tests as holistically as possible, by implementing multiple NDT methods simultaneously in order to record the crack initiation and propagation until the final fracture. In addition to well-known methods such as strain gauges, thermography, and ultrasound, the crack luminescence method developed at the Bundesanstalt für Materialforschung und -prüfung (BAM), which makes cracks on the surface particularly visible, was also used. For data acquisition, a first data fusion concept was developed and applied in order to synchronize the data of the different methods and to evaluate them to a large extent automatically. The resulting database can ultimately also be used to access, view, and analyze the experimental data for various NDT methods. During the conducted fatigue tests, the simultaneous measurements of the same cracking process enabled a comprehensive comparison of the methods, highlighting their individual strengths and limitations. More importantly, they showed how a synergetic combination of different NDT methods can be beneficial for implementation in large-scale fatigue testing but also in monitoring and inspection programs of in-service structures - such as the support structures of offshore wind turbines. T2 - Fatigue Design 2023 (FatDes 2023) CY - Senlis, France DA - 29.11.2023 KW - Fatigue KW - Welded KW - NDT KW - Crack growth PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-600238 DO - https://doi.org/10.1016/j.prostr.2024.03.062 VL - 57 SP - 560 EP - 568 PB - Elsevier B.V. AN - OPUS4-60023 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maack, Stefan T1 - Elastic wave propagation of ultrasound in bituminous road surfaces – simulations and measurements N2 - Maintenance costs of road infrastructure are increasing steadily. Adverse environmental impacts on infrastructure get more and more important as well. Therefore, it is important to determine how limited financial resources can be directed with an optimum pay-out. The present study takes first steps towards the usage of low-frequency ultrasound as a tool to evaluate the road condition. T2 - International Symposium Non-Destructive Testing in Civil Engineering 2015 CY - Berlin, Germany DA - 15.09.2015 KW - Wave propagation KW - Ultrasonic KW - NDT KW - Simulation PY - 2015 AN - OPUS4-38837 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kanzler, D. T1 - Probability of detection in nondestructive testing N2 - Motivation: What can we learn from the history of aerospace? State of the art: Detectability as the basis of probability of failure Evaluationmethods: Consequences of decisions based on ndt Advanced approaches: Probability of Detection: Evaluation of ndt systems are important! Use of the POD: Out of the box: Finnish and Swedish project for final disposal of spent nuclear fuel T2 - InnoTesting CY - Wildau, Germany DA - 25.02.2016 KW - NDT KW - Reliability KW - POD PY - 2016 AN - OPUS4-37586 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bertovic, Marija T1 - Automation in NDT: new risks and risk sources N2 - Reliability of NDT depends not only on the intrinsic capability of the measuring systems and on the application factors (the conditions under which NDT is applied), but also—and to a great extent—on human factors and the organisational context under which each inspection is carried out. Adoption of a systematic approach to the identification and prevention of risks. Critical defects could be missed, even if the inspection process is semi-automated. The causes of that risk lie in the technology, people and in the organisation. Currently installed preventive measures are insufficient to prevent from risks New preventive measures could be installed, e.g. further automation, installing alarms, implementing human redundancy, developing software and hardware solutions, optimising procedures, etc. Human factors studies are not only essential for the operation but also during the development process. T2 - 55th annual Conference of the British Institute for Non-Destructive Testing CY - Nottingham, UK DA - 12.09.2016 KW - NDT KW - Risk management KW - Reliability KW - Human factors PY - 2016 AN - OPUS4-37589 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bertovic, Marija T1 - Automation in non-destructive testing: new risks and risk sources N2 - Over the past couple of decades Non-Destructive Testing (NDT) has seen a significant increase in the use of automation. In addition to increased reliability, objectivity, consistency, repeatability, productivity, and so on, automating parts of the process is expected to decrease the potential for human error. However, the literature on human-automation interaction suggests that automation is not only associated with benefits, but also with new risks and risk sources. First, this paper will present the methodology used to identify—for the first time—possible risks associated with mechanised data acquisition and corresponding data evaluation. Moreover, it will highlight possible risks, their causes, consequences, and ways of preventing them. Second, those preventive measures will be further analysed by examining new risks that can arise from their implementation, i.e. potential for failure that can arise from (a) working with automated defect-detection and sizing aids, (b) implementing human redundancy, and (c) improvement of the inspection procedures without due consideration of the procedure users. And third, some optimisations strategies will be provided. The purpose of this work is to show that mechanised testing is associated with potential for failure and that the sources of those risks go beyond single inspectors and need to be looked at in the interaction of people with other systems, i.e. the technology, the team and, most importantly, the organisation. T2 - 55th annual Conference of the British Institute for Non-Destructive Testing CY - Nottingham, UK DA - 12.09.2016 KW - NDT KW - Automation KW - Reliability PY - 2016 SP - 1 EP - 11 AN - OPUS4-37591 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmerich, Rosemarie T1 - Is data obtained through Non-destructive Testing reliable? N2 - Civil engineers, who are involved in nondestructive testing have to solve an essential task: the transfer of the results of NDT-research into practice. NDT in civil Engineering is a quite new discipline. The results must meet the needs of the infrastructure owners to convince them about the usefulness of NDT. The issue of reliability of the NDT-data was discussed. T2 - Reliability Workshop Polytechnical University HongKong CY - Hong Kong, China DA - 06.04.2016 KW - Civil infrastructure KW - Reliability KW - POD KW - NDT PY - 2016 AN - OPUS4-37545 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kanzler, D. A1 - Müller, Christina T1 - How much information do we need? A reflection of the correct use of real defects in POD-evaluations N2 - To evaluate the capability of a non destructive testing system the “truth” of the used defects is essential. But what exactly is the truth of a real defect? And how much information is usable for the study? This presentation gives an overview about an advanced use of multiple metallographic cuts for the POD evaluation. In the presentation an approach is shown where information of metallographic studies are reconstructed and weighted to gain the essential information about real defects and which information are important for the detection with radiographic testing equipment. Furthermore, different connection points are discussed were additional knowledge from simulation and artificial defects can be used to gain additional certainty for the result of the evaluation. The methodology is used for the evaluation for the digital radiographic testing system for the testing of electron-beam welds, which is one possible choice to seal the Finnish copper canisters for the final deposit of spent nuclear fuel. T2 - 42nd annual review of progress in quantitative nondestructive evaluation: Incorporating the 6th European-American Workshop on Reliability of NDE CY - Minneapolis, MN, USA DA - 25.07.2015 KW - NDT KW - POD KW - Radiography PY - 2016 DO - https://doi.org/10.1063/1.4940652 SN - 0094-243X VL - 1706 SP - 200008-1 EP - 200008-7 PB - AIP Publishing AN - OPUS4-37596 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Christina T1 - Analysis and synthesis of NDT reliability using the extended modular model N2 - The aim of all the effort devoted to NDE reliability is to evaluate the reliability accurately, reliably and efficiently, in accordance with the specific requirements of industrial application taking into account the very different nature of influencing factors. The set up of the Modular Reliability Model in 1997 was a big step forward in the understanding of influencing mechanisms in terms of the three different main elements, i.e. the intrinsic capability (IC), the application parameters (AP) and the human factors (HF). The intrinsic capability stands for the pure physical-technological process of the signal detection caused by the waves or the rays from a material defect in the presence of noise (caused by the material and the devices). This intrinsic capability is the upper bound of the possible reliability. Already when measuring this intrinsic capability for thick walled components the original one-parameter POD should be extended to a multi-parameter POD, where, in addition to the defect size, a number of additional physical parameters, such as the grain size distribution (or attenuation), defect depth, and angle or surface roughness, must be considered. For real life cycle assessments it is necessary to evaluate the signal response from real defects. The industrial application factors, e.g. coupling conditions, limited accessibility, heat and environmental vibrations, diminish the reliability. The amount of reduction can be determined quantitatively, if the underlying conditions are controlled. In case they are not controlled it is necessary to count for a (unknown) fluctuation in the reliability in the field anyway. The third group of important influencing factors are the human factors, which do not only cover the individual performance capability of the inspectors but also the design of the working place, the procedure, the teamwork quality, interaction with systems, the organization, and finally, the relationship between the companies involved in the inspection process and to which extend the responsible parties are aware of it. Both the internal and external organizational context, affect not only the HF but also the IC and AP. After having analysed the single factors separately it is necessary to look how everything is interconnected. When comparing an “ideal inspection” with a “real inspection” it is worthwhile to look at the existing practices, rules and standards. How do they really support reliable testing? With respect to the industrial end user, it needs to be shown how the level of reliability of NDE, influenced by the different factors and their interaction, has an impact on acceptance or rejection of safety critical parts. The approach of analysis and synthesis will be illustrated by examples of the reliability investigation of the inspection of copper canisters for nuclear fuel deposit in Sweden and Finland and German Railway inspections (hollow axle testing). T2 - 19th World Conference on Non-Destructive Testing CY - München, Germany DA - 13.06.2016 KW - NDT KW - Reliability KW - Modular model PY - 2016 AN - OPUS4-37602 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Selby, G. T1 - Observations on implementation of the BAM holistic reliability model N2 - Achieving reliability in NDE for nuclear power plants is a complex challenge. As engineers we tend to focus on the equipment and the written procedures; they are easy for us to understand, measure and control. This focus addresses only one of the four aspects of the BAM holistic model, namely, Intrinsic Capability. Another of the model's modules, Application Parameters, also is engineering-oriented as examiners work to ensure that the equipment and procedure can be applied correctly in the actual examination environment as it is found in the field, though in addition to engineering it requires organizational foresight and commitment to understand and prepare for that specific environment well in advance. The Human Factors reliability module is harder for us to think about. The procedure developers think, "Of course all the examiners in the field will understand all aspects of my procedure and execute them correctly." Most of our bad experiences with reliability occur when this happy thought turns out to be untrue. And finally, perhaps the hardest reliability module to affect is Organizational Context. Getting all of the stakeholders -- the plant owner, the NDE company, the examiners, the regulators, the qualification body, the equipment suppliers -- to think about reliability in the same way, years in advance of the examination, to think about reliability at every step in the long process leading to the day of the examination itself, is a heavy lift indeed. T2 - 19th World Conference on Non-Destructive Testing CY - München, Germany DA - 13.06.2016 KW - NDT KW - Reliability KW - Modular model PY - 2016 AN - OPUS4-37603 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kanzler, Daniel T1 - Evaluating RT systems with a new POD approach N2 - The usefulness and purpose of evaluating nondestructive testing (NDT) systems and their capabilities has changed in the last decade. The conventional method of simply applying a familiar statistical algorithm to say whether the system is usable for the tasks is history. Nowadays, multiple parameter methods which describe the probabilities of detection (POD) of different systems or real defects need new characteristics and a broader variety of statistical models to describe the true system behaviour. The appraisal of the NDT system involves diverse departments within a company (engineering, NDT-operators, and statisticians), but is, at the same time, more needed and requested than in the past. In this article, an approach is discussed in which professionals from different fields worked well together, accomplishing cost-intensive metallographic studies in correlation with well-understood physical behaviour of NDT-methods as well as deep-discussed mathematical methods to create a holistic evaluation of the technical reliability for a specific radiographic testing (RT) equipment. The first part of the publication will show the comparison between metallographic grinding and the RT indications. An essential innovation over past evaluation methods was the use of a multi-scale smoothing algorithm, which describes physical parameters, which were not used in evaluation like the POD in this way in the past. In the second part the statistical requirements for the POD take the focus. It can often be hard to make significant statements; especially in the case where only a small amount of data is available. The combination of data and the use of knowledge from simulations are essential. One possible solution will be shown for the RT evaluation. The methodology is used for evaluating the digital RT system for the inspection of electron-beam welds, which was method considered to seal the Finnish copper canisters for the final deposit of spent nuclear fuel. T2 - 19th World Conference on Non-Destructive Testing CY - München, Germany DA - 13.06.2016 KW - NDT KW - Reliability KW - POD KW - RT PY - 2016 AN - OPUS4-37607 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Trappe, Volker T1 - Infinite life of CFRP evaluated non-destructively with X-ray-refraction topography in-situ mechanical loading N2 - Carbon Fibre Reinforced Plastics (CFRP) are more and more used in modern civil aircrafts. These days the whole fuselage is made of this material (B787; A350). Due to strict certification standards the normal in-service loading gives a low stress level compared to the static and even the fatigue strength of the material. Hence CFRP are assumed to have an infinite life. To evaluate this assumption, fatigue tests on CFRP-specimens were performed up to 108 load cycles and the first inter-fibre failure was evaluated non-destructively by accompanying X-ray-refraction topography. A tensile testing machine was integrated in a small angle X-ray scattering (SAXS) setup. X-ray refraction topography was performed while the CFRP-samples were tensile loaded. This non-destructive technique enables the detection of micro-cracking and inter-fibre failure especially for CFRP. For Glass Fibre Reinforced Plastic (GFRP) X-ray refraction and in-situ loading has already been successfully used. The increase of inner surfaces due to inter fibre failure was measured as a function of the stress state. Fatigue tests were performed at and below the limit of inter-fibre failure strength. State of the art is to assume the failure of the samples under cyclic loading as the fatigue life. Accompanying non-destructive X-ray refraction measurements reflects the damage state and enables to trace its evolution even if the total failure of the specimens does not occur. This investigation technique is of high interest to give the engineer a design value of infinite life which is practically often reached due to knock down factors of certification standards. Finally the infinite life was found for cyclic fatigue loaded CFRP-samples even under high inter fibre transverse and shear loading investigated up to 108 load cycles. T2 - 19th World Conference on Non-Destructive Testing CY - Munich, Germany DA - 13.06.2016 KW - CFRP KW - NDT KW - Fatigue KW - Damage evolution PY - 2016 AN - OPUS4-37567 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -