TY - THES A1 - Schempp, Philipp T1 - Grain refinement in aluminium GTA welds N2 - Grain refinement is an important opportunity to improve mechanical properties of fusion welds and the weldability (cracking sensitivity) of the base metal. In this thesis, grain refinement was achieved for aluminium welds by additions of a grain refiner. For this purpose, inserts consisting of aluminium base metal and small additions of commercial Al Ti5B1 grain refiner were cast, deposited in base metal plates, and fused in a gas tungsten arc (GTA) welding process. As a result, higher grain refiner additions increased the weld’s titanium and boron content resulting in a significant decrease in the weld metal mean grain size up to 86%. This grain size reduction led to a transition from predominantly columnar to equiaxed grain shape (columnar to equiaxed transition CET). The grain refinement was thereby found to be strongly dependent upon the base metal chemical composition. Accordingly, the grain refining efficiency was the highest in commercial pure Al (Alloy 1050A, Al 99.5), followed by Alloy 6082 (Al Si1MgMn) and Alloy 5083 (Al Mg4.5Mn0.7). In this regard, the parameters P and Q were applied to investigate the influence of alloying elements on the supply of constitutional undercooling during solidification and on final grain size. Also, WDS (wavelength dispersive x-ray spectroscopy) and TEM (transmission electron microscopy) analysis found an increasing number of particles rich in Ti and B. These substrates are probably TiB2 particles coated by Al3Ti likely nucleating Al grains during solidification. The variation in torch speed showed that increasing torch speeds support the CET effect leading to many small and equiaxed grains at high torch speed. To give explanations for this observation, the thermal conditions, that are controlled by welding parameters such as torch speed, were determined with temperature measurements via thermocouples. These measurements revealed that solidification parameters like solidification growth rate, cooling rate, (local) thermal gradient and solidification time vary significantly along the solidification front (from weld centreline to weld fusion line). In a further step, the solidification parameters were related to the corresponding grain size and shape. On the basis of this comparison, an analytical approach was used to model the CET. This allowed the prediction of critical values for both solidification growth rate and thermal gradient, at which the CET occurs in aluminium weld metal. The influence of grain refinement on the weld mechanical properties was investigated in tensile tests. Accordingly, the ductility of Alloy 5083 welds was increased through grain refinement whereas no improvement in weld metal strength was observed. Furthermore, tear tests with notched specimens revealed for Alloy 1050A that the resistance against initiation and propagation of cracks in the weld metal can be enhanced through grain refinement. In addition, when welding Alloy 6082, weld metal grain refinement prevented the formation of centreline solidification cracking that was present only in welds with unrefined grain structure. On the basis of the above experiments, the Ti/B contents needed in commercial filler wires or rods to allow optimum weld metal grain refinement were estimated. Accordingly, this work gives specific recommendations to filler material producers through a simple calculation that considers the influence of base alloy and welding process. The results show that the Ti/B contents defined by the corresponding standards for filler alloys are too low to allow weld metal grain refinement. T3 - BAM Dissertationsreihe - 111 KW - Aluminium KW - Kornfeinung KW - WIG-Schweißen PY - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-477 SN - 978-3-9815944-4-7 SN - 1613-4249 VL - 111 SP - 1 EP - 121 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-47 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Perret, William T1 - Welding Simulation of Complex Automotive Welded Assembly - Possibilities and Limits of the Application of Analytical Temperature Field Solutions N2 - Before the development of computational science, heat conduction problems were mainly solved by analytical techniques. Analytical solutions are exact solutions of differential equations; the investigated physical phenomena, for instance the temperature, are solved locally for one single point independently of the rest of the investigated structure resulting in extremely short computational times. These analytical solutions are however only valid for some simple geometries and boundary conditions making their applications for complex industrial geometries directly not possible. Numerical techniques, such as the Finite Element Method, enable overcoming this problem. However, the numerical simulation of the structural heat effect of welding for complex and large assemblies requires high computational effort and time. Therefore, the wide application of welding simulation in industry is not established, yet. The aim of this study is to combine the advantages of analytical and numerical simulation methods to accelerate the calibration of the thermal model of structure welding simulation. This is done firstly by calibrating automatically the simulation model with a fast analytical temperature field solution and secondly by solving the welding simulation problem numerically with the analytically calibrated input parameters. In order to achieve this goal, the analytical solution of the heat conduction problem for a point source moving in an infinite solid was extended and validated against reference models until a solution for a volumetric heat source moving on a thin small sheet with several arbitrary curved welding paths was found. The potential of this analytical solution by means of computational time was subsequently demonstrated on a semi-industrial geometry with large dimensions and several curved welds. The combined method was then transferred to an industrial assembly welded with four parallel welds. For this joint geometry, it was possible to apply the extended analytical solution. The calibration of the simulation model was done automatically against experimental data by combining the extended fast analytical solution with a global optimisation algorithm. For this calibration, more than 3000 direct simulations were required which run in less computational time than one corresponding single numerical simulation. The results of the numerical simulation executed with the analytically calibrated input parameters matched the experimental data within a scatter band of ± 10 %. The limit of the combined method is shown for an industrial assembly welded with eight overlap welds. For this joint geometry, a conventional numerical approach was applied, since no analytical solution was actually available. The final simulation results matched the experimental data within a scatter band of ± 10 %. The results of this work provide a comprehensive method to accelerate the calibration of the thermal model of the structure welding simulation of complex and large welded assemblies, even though within limitation. In the future, the implementation of this method in a welding simulation tool accessible to a typical industrial user still has to be done. T3 - BAM Dissertationsreihe - 108 KW - Schweißen KW - industrielle Anwendung KW - Simulation KW - analytische Lösung KW - komplexe Geometrie PY - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-505 SN - 978-3-9815944-0-9 SN - 1613-4249 VL - 108 SP - 1 EP - 183 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-50 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Günzel, Stephan T1 - Analyse der Schädigungsprozesse in einem kurzglasfaserverstärkten Polyamid unter mechanischer Belastung mittels Röntgenrefraktometrie, Bruchmechanik und Fraktografie N2 - In der vorliegenden Arbeit wird das Schädigungsverhalten eines kurzglasfaserverstärkten Polyamids analysiert. Die Mikrorissschädigung wird mittels Röntgenrefraktionsanalyse für verschiedene mechanische Betriebsbelastungen untersucht. Dabei werden Möglichkeiten und Grenzen der Röntgenrefraktionsanalyse für kurzglasfaserverstärkte Polyamide herausgearbeitet. Insbesondere werden der Einfluss der Faserorientierungsverteilung und der Einfluss der Schädigungsmechanismen auf die Röntgenrefraktionsanalyse und deren Ergebnisinterpretation betrachtet. Die Methode ermöglicht eine quantitative und phänomenologisch basierte Mikrorissschädigungscharakterisierung. Für den untersuchten Werkstoff tritt Mikrorissschädigung in Form von Faser-Matrix-Ablösung und Matrixrissbildung auf. Die Schädigungshöhe korreliert linear mit dem nichtlinear elastischen Dehnungsanteil und ist abhängig von der Art der Betriebsbelastung. Eine Feuchtigkeitsaufnahme des Werkstoffs kann das Mikrorissschädigungsverhalten deutlich beeinflussen. Die Schädigung durch Mikrorissbildung tritt vorrangig unter Zugbelastungen auf. Die Makroschädigung durch Einzelrissfortschritt wird in Abhängigkeit der Faserorientierung und des Feuchtegehalts in einem automatisierten Versuch charakterisiert. Aufgrund der gewonnenen Erkenntnisse wird ein empirisches Berechnungsmodell erstellt. Die Untersuchungen des Mikro- und Makroschädigungsverhaltens werden fraktografisch begleitet, um die in den Modellvorstellungen vorausgesetzten Schädigungs- und Versagensmechanismen abzusichern. N2 - This thesis presents an analysis of the damage behaviour in a short glass fibre reinforced polyamide. The micro cracking is investigated by X-ray refraction technique under various, mechanical in-service loadings. In this context, potentials and limits of X-ray refraction analysis for short glass fibre reinforced polyamides are compiled. In particular the influence of fibre orientation and the influence of damage mechanisms are examined according to the X-ray refraction analysis and its interpretation. The method offers a quantitative and phenomenological based characterisation of micro crack damage. For the investigated material micro crack damage emerges as fibre matrix debonding and matrix micro cracking. The state of damage correlates with a nonlinear strain portion in a linear manner and depends on the kind of loading. Absorption of moisture in the material may influence significantly the micro crack damage behaviour. Damage of micro cracking appears preferentially under tension. The macro damage due to propagation of a single crack is characterised in an automated test setup, considering the fibre orientation and content of moisture. Based on the findings an empirical assessment approach is developed. The investigations of the micro and macro damage behaviour are accompanied by fractography, in order to support the model assumptions according to damage and fracture mechanisms. T3 - BAM Dissertationsreihe - 97 KW - Schädigung KW - Betriebsfestigkeit KW - Kunststoff KW - faserverstärkt KW - zerstörungsfrei PY - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-617 SN - 978-3-9815360-4-1 SN - 1613-4249 VL - 97 SP - 1 EP - 188 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Scholz, Christian T1 - Low friction slip-rolling contacts - Influences of alternative steels, high performance thin film coatings and lubricants N2 - Due to the growing environmental awareness worldwide, containment provisions for CO2 emissions in mobility systems and increasing performance requirements the demands on mechanical systems and their materials continuously rise. These high demands require the implementation of new technical approaches, for example of light-weight strategies in automotive powertrains, and directly raise questions about the suitability of the most promising technical solution. Two basic parameters, the surface hardness of the tooth flanks and the core fatigue strength of the tooth root, illustrate exemplarily increasing demands on material grades used for gear wheels in automotive powertrains. In addition to light-weight strategies, a reduction in friction and an increase of the fatigue lifetime are two other major development directions to strive the mentioned targets. It is clear that any kind of solution must show an equal application profile, preferably an improvement, compared to the state-of- the-art solutions. For tribological systems, the following paths may offer lower friction and higher load carrying capabilities: 1. Alternative base oils and additives (such as esters, polyglycols), 2. Thin film coatings (e.g. DLC) and/or 3. Novel steel metallurgies. In previous investigations on the slip-rolling resistance of thin film coatings (a-C, ta-C, Zr(C,N)) the substrates were mainly made of the bearing steels 100Cr6H and Cronidur 30. Applying contact pressures of up to P0max = 2.9 GPa (FN = 2,000 N), the samples were tested up to 10 million load cycles in endurance tests. The aim of the present work is to broaden the research by varying the input parameters. Newly developed engine oil mixtures, high performance thin film coatings and alternative steel solutions are intensively investigated in highly stressed slip-rolling contacts at lubricant temperatures of 120°C. Specifically, in using new steel metallurgies, i.e. the high toughness and high strength steels V300 and NC310YW (Aubert & Duval) as well as CSS-42L (Latrobe Specialty Steel Company), in combination with thin film coatings, even if they compete in the uncoated state, the Hertzian contact pressures could be increased up to P0max = 4.2 GPa (FN = 5,000 N) without any surface failures of coating or substrate. It was shown that selected thin film coatings can minimize the wear rates down to nearly ‘zero-wear’ in highly stressed contacts [Woy08] [Woy11]. In addition, the studies revealed not only the high potential in slip-rolling resistance, but also a possible friction reduction down to 0.047 by use of uncoated steels with increased toughness. Compared to steels like 100Cr6H and Cronidur 30 this means a reduction in friction of approximately 40% under identical testing conditions. Different test series with newly developed base oil-additive formulations were investigated with specific emphasis on the frictional behavior of selected bio-no-tox EP/AW additives and friction modifiers. Additional influencing factors like the structural and surface conditions of the steels/coatings before and after the tests were analyzed by means of REM, EDX, XRD and TEM. T3 - BAM Dissertationsreihe - 96 KW - hoch zähe Si-Stähle KW - geringe Reibung KW - DLC KW - Zr (C, N) PY - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-624 SN - 978-3-9815134-2-7 SN - 1613-4249 VL - 96 SP - 1 EP - 153 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-62 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Natte, Kishore T1 - Synthesis of novel polymeric hybrid nanoparticles with enhanced interfacial and colloidal properties for biomedical studies N2 - Die geringe Größe von Nanopartikeln (Durchmesser < 100 nm) gewährleistet sowohl eine hohe spezifische Oberfläche sowie Permeabilität durch eine Vielzahl biologischer Systeme. Als Folge weisen Nanopartikel (NP) eine starke Wechselwirkung mit biologischen Systemen auf, wodurch diese in den letzten Jahren zunehmend in der biomedizinischen Forschung Anwendung fanden. Aufgrund der relativ geringen Toxizität sowie der Möglichkeit zur Einführung unterschiedlicher funktioneller Gruppen eignen sich besonders auf Siliziumdioxid (Silica)basierende Nanopartikel für biomedizinische Studien. Der Schwerpunkt dieser Doktorarbeit lag in der Synthese und Charakterisierung von neuartigen Hybrid-NP mit verbesserten Eigenschaften für biologische Studien. Insbesondere soll eine Unterdrückung der Proteinadsorption erlangt werden sowie stark fluoreszierende NP in Gegenwart serumreicher Medien erhalten werden. Zu Beginn wird der Syntheseweg zur Darstellung hoch fluoreszierender Silica-Nanopartikel präsentiert, durch kovalente Anbindung des Alexa Farbstoffs und nachfolgender Ummantelung durch eine zusätzliche Silicahülle. Diese Nanopartikel wurden mittels dynamischen Lichtstreuung (DLS), Transmissionselektronenmikroskopie (TEM) und Fluoreszenzspektroskopie untersucht. Letztgenannte Methode beinhaltet die Bestimmung der absoluten Quantenausbeute solcher streuenden Suspensionen mit einer integrierenden Kugelkonfiguration sowie die Zuordnung von Helligkeitswerten. Bei geringer Ausdehnung der Hülle zeigen Silica NP mit Kern-Schale Architektur eine glatte Oberfläche und hohe Quantenausbeuten, in Größenordnung der freien Farbstoffe. Eine Erhöhung der Menge an Hüllen-Precusor führt zu einer himbeerartigen Morphologie der Oberfläche und einer Verminderung der Quantenausbeute. Es folgt die Darstellung zweier unterschiedlicher Typen neuartiger Silica- Polyethylenglykolhybride NP (H-SiO2-PEG und G-SiO2@PEG) unter Verwendung desselben polymerprecursors oder desselben polymerprecursors: Der Einfluss der Konzentration des polymerpreursors Poly(ethylen glykol) methylether-3-(triethoxysilyl) propylurethan (mPEG- IPTES) auf die Partikeleigenschaften wurde ausführlich untersucht. Bei polymergepfropften NP bestimmt die Konzentration des polymer precursors die Dichte des angekoppelten PEGs und folglich die Hydrophobieder NP Oberfläche. Dagegen beeinflusst bei kondensierten NP der precursor die Partikelgröße, aber nicht die Dichte der Polymerketten auf der Oberfläche. Abschließend wird der Einfluss der Polymerlänge auf die Verminderung der BSA Adsorption beschrieben. SNPs@PEG mit verschiedenen Molekulargewichten des mPEG (Mw = 350, 2000 und 5000 g/mol) wurden an die NP Oberfläche durch nucleophile Substitution von tosyliertem mPEG an aminierte Silica NP kovalent angebunden (hemisches Pfropfen). Die resultierenden Hybrid-NP wurden einheitlich mittels DLS, TEM, Fourier- Transformations-Infrarotspektroskopie (FTIR), thermogravimetrischer Analyse (TGA)und Photoelektronenspektroskopie (PES) charakterisiert. Bovine Serum Albumin (BSA) wurde in verschiedenen Konzentrationen als Modellprotein verwendet, um die Ausbildung der protein corona durch Adsorption an ursprünglichen sowie an modifizierten NP oder modifizierten NPs(SNPs@PEG) zu untersuchen. Das Zeta-Potenzial der ursprünglichen Silica NP sowie SNPs@PEG (Mw = 350 g/mol) zeigen eine dynamische Entwicklung der Nanopartikel- protein coronain Abhängigkeit von der Inkubationsdauer (0, 24, 48 h). Im Gegensatz hierzu konnte bei SNPs@PEG mit Mw 2000 g/mol eine signifikante Minderung der Ausbildung der protein corona sowie der zeitlichen Entwicklung beobachtet werden. Insgesamt wird die protein corona stark von den adsorptionshindernden Eigenschaften des PEGs beeinflusst. N2 - The reduced size of nanoparticles (diameter < 100 nm) confers them high specific surface areas and permeability through many biological pathways resulting in high interaction with biological systems. Therefore, in the recent years, nanoparticles (NPs) have increasingly found many applications in biomedical research. Herein, silica-based NPs are among the most promising candidates for biomedical studies due to their relative low toxicity and the possibility of functional variability. The main focus of this thesis work has been the synthesis and characterisation of novel hybrid NPs with enhanced properties for biomedical studies. More specifically, suppression of protein adsorption and achievement of highly fluorescent NPs in serum-rich media are well focused. First, a chemical strategy for the preparation of highly fluorescent silica nanoparticles by covalent attachment of Alexa dyes and subsequent shielding by an additional pure silica shell is well presented. These nanoparticles were investigated by Dynamic light scattering (DLS), Transmission electron microscopy (TEM) and fluorescence spectroscopy, the latter includes determination of absolute fluorescence quantum yields of such scattering suspensions with an integrating sphere setup and the assignment of fluorescence intensity values. At low shelling extension core-shell fluorescent silica nanoparticles show smooth surfaces and high quantum yields, even comparable to those for free dyes. However, by increasing the amount of shell precursor, nanoparticle surfaces show raspberry morphologies and decay of the quantum yields. Secondly, two different types of novel silica-poly(ethylene glycol) hybrid nanoparticles (H- SiO2-PEG and G- SiO2@PEG) have been synthesized by use of the same polymer precursor: Here the influence of concentration of the polymer precursor poly(ethylene glycol) methyl ether-3-(triethoxysilyl) propyl urethane (mPEG-IPTES) on the particle properties was scrutinised. For polymer grafted NPs, the concentration of polymer precursor increases the PEG density and the hydrophobicity of the NPs surface. On the other hand, for condensated NPs, the polymer precursor influences the size, but not the density of polymer chains on the NPs surface, which indicates that PEG on the surface of the NPs effectively reduces the adsorption of Bovine serum albumin (BSA). Finally, the influence of polymer length on the ability to repel BSA adsorption onto nanoparticles is reported. SNPs@PEG with different molecular weights (mPEG: 350, 2000 and 5000 g/mol) were synthesized by nucleophilic substitution of tosylated mPEG to aminated silica nanoparticles (chemical grafting). The resulted hybrid nanoparticles were consistently characterized by DLS, TEM, Fourier transform infrared spectroscopy (FTIR), Thermogravimetric analysis (TGA) and X-ray photoelectron spectroscopy (XPS). BSA at different concentrations were used as a model protein to study the protein-corona formation after adsorption onto the pristine and modified nanoparticles (SNPs@PEG). For pristine SNPs and SNPs@PEG (MW = 350 g/mol), zeta potential at different incubation times (0, 24 and 48 h) show a dynamic evolution of the nanoparticle-protein corona. Conversely, for SNPs@PEG with MW ≥ 2000 g/mol, a significant suppression of corona formation and time evolution was observed. In resume, protein corona is strongly influenced by the adsorption inhibition of PEG surfaces. T3 - BAM Dissertationsreihe - 99 KW - Silica KW - PEG KW - Fluoreszierende Nanopartikel KW - Hybridnanopartikel KW - Hybrid nanoparticles KW - Corona KW - Fluorescent particles PY - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-596 SN - 978-3-9815360-7-2 SN - 1613-4249 VL - 99 SP - 1 EP - 115 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-59 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR T1 - Amts- und Mitteilungsblatt, Band 43, Heft 1 T3 - Amts- und Mitteilungsblatt der BAM - 1/2013 PY - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-83 SN - 0340-7551 VL - 43 IS - 1 SP - 1 EP - 155 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-8 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gallo, Emanuela A1 - Sánchez-Olivares, G. A1 - Schartel, Bernhard T1 - Flame retardancy of starch-based biocomposites - aluminium hydroxide-coconut fiber synergy N2 - The use of coconut fiber (CF) agricultural waste was considered as an environmentally friendly and inexpensive alternative in flame retarded biocomposites. To decrease the high content of aluminum trihydrate (ATH) required, the thermal decomposition (thermogravimetry), flammability [oxygen index (LOI) and UL 94 test] and fire behavior (cone calorimeter) of a combination of CF and ATH were investigated in a commercial blend of thermoplastic starch (TPS) and cellulose derivatives. CF induced some charring activity, slightly decreasing the fire load and burning propensity in cone calorimeter test. ATH decomposes endothermically into water and inorganic residue. Significant fuel dilution as well as a pronounced residual protection layer reduces the fire hazards. Replacing a part of ATH with coconut fibers resulted in improved flame retardancy in terms of ignition, reaction to small flame, and flame-spread characteristics [heat release rate (HRR), fire growth rate (FIGRA), etc.]. The observed ATH and CF synergy opens the door to significant reduction of the ATH contents and thus to interesting flame retarded biocomposites. KW - Biocomposites KW - Flammability KW - Starch KW - Aluminium hydroxide KW - Coconut fiber PY - 2013 SN - 0032-2725 VL - 58 IS - 5 SP - 395 EP - 402 PB - Industrial chemistry research inst CY - Warszawa, Poland AN - OPUS4-28513 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gallo, Emanuela A1 - Schartel, Bernhard A1 - Schmaucks, G. A1 - von der Ehe, Kerstin A1 - Böhning, Martin T1 - Effect of well dispersed amorphous silicon dioxide in flame retarded styrene butadiene rubber N2 - Spherically shaped amorphous silicon dioxide with broad size particle distribution was used in combination with aluminium trihydroxide (ATH) in styrene butadiene rubber composites. The pyrolysis, flammability, fire properties, flame spread and gas diffusion were investigated. The kind and amount of ATH, but in particular the fine silicon dioxide chosen as an additive, influenced the thermal decomposition and fire behaviour of styrene butadiene rubber composites. Gravimetric gas sorption measurements showed that the gas diffusion was systematically lower with silicon dioxide. The initial pyrolysis gas release was hindered, increasing the temperature at which decomposition begins as well as the ignition time in fire tests. During combustion, ATH and silicon dioxide accumulate on the surface of the specimen, forming a residual protective layer. A reduced peak heat release rate and fire spread were observed. The addition of a special kind of silicon dioxide is proposed to play a key role in optimising fire retardancy. KW - Flame retardancy KW - Styrene butadiene rubber KW - SBR KW - Silicon dioxide KW - Aluminium trihydroxide KW - ATH PY - 2013 U6 - https://doi.org/10.1179/1743289812Y.0000000012 SN - 1465-8011 SN - 1743-2898 VL - 42 IS - 1 SP - 34 EP - 42 PB - IOM Communications CY - London, UK AN - OPUS4-27626 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schukar, Vivien A1 - Kusche, Nadine A1 - Kalinka, Gerhard A1 - Habel, Wolfgang T1 - Field deployable fiber bragg grating strain patch for long-term stable health monitoring applications N2 - A fiber Bragg grating (FBG) strain patch specially adapted for long-term and high-strain applications has been developed and characterized. The design concept for the patch is based on a glass-fiber reinforced plastic (gfrp) carrier material. The developed concept for the FBG integration into the carrier material was derived from reliable integration procedure of FBG sensors into composite structures. The patches' temperature sensitivity, strain gauge factor, fiber–matrix interface adhesion and fatigue behavior were characterized. As a result, FBG strain patches with linear temperature and strain behavior, as well as excellent fatigue resistance, were developed and can be used as part of a monitoring system for advanced composite materials in aerospace structures or wind turbine power plants. KW - Fiber Bragg grating KW - Patch KW - Strain gauge factor KW - Temperature sensitivity KW - Push-out test KW - Validation KW - Fatigue behavior PY - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-276271 SN - 2076-3417 VL - 3 IS - 1 SP - 39 EP - 54 PB - MDPI CY - Basel AN - OPUS4-27627 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Rübner, Katrin A1 - Schneider, S. A1 - Beck, T. A1 - Flassenberg, G. A1 - Herbst, Tristan T1 - Stoffkreislauf im Mauerwerksbau - Nachhaltigkeitsanalyse für das Mauerwerksrecycling / Schlussbericht zum IGF-Vorhaben 17022 N N2 - In Deutschland fallen mittelfristig erhebliche Mengen von Mauerwerkbruch an. Aus dem jährlichen Bauschuttanfall und den Produktionszahlen von Wandbausteinen lassen sich die Mengen an Mauerwerksrestmassen ableiten, die als Rückbaumaterial bei Abriss-, Umbau und Sanierungsarbeiten in Deutschland anfallen werden. Hiernach ist pro Jahr mit bis zu 10 Millionen Tonnen heute vornehmlich heterogen anfallendem Mauerwerkbruch zu rechnen [1a]. Im Sinne einer nachhaltigen Kreislaufwirtschaft sind diese Restmassen zukünftig einem möglichst hochwertigen Recycling zuzuführen. In diesem Spannungsfeld führt die deutsche Mauersteinindustrie das breit aufgestellte gemeinschaftliche Forschungsprojekt "SIM Stoffkreislauf im Mauerwerksbau" durch. In insgesamt acht mauersteinübergreifenden IGFForschungsvorhaben wurden und werden technisch orientierte Lösungsmöglichkeiten für das Recycling von Mauerwerk erarbeitet und Anwendungsbereiche für Mauerwerksrestmassen aufgezeigt. Eine grundsätzliche Entscheidung über die Eignung von Mauerwerksrestmassen für bestimmte Recyclingwege kann es letztlich nicht geben. Es wird immer eine Einzelfallentscheidung bleiben, die wesentlich durch komplexe technische sowie ökologische und ökonomische Randbedingungen geprägt wird. Vor diesem Hintergrund wurde im Rahmen des IGF-Forschungsvorhabens 17022 N der Forschungsvereinigung Porenbetonindustrie e.V., Berlin die Nachhaltigkeit verschiedener Recyclingoptionen für Mauerwerkbruch ganzheitlich untersucht und bewertet. Unter Einbeziehung der Hauptwandbausteinarten Ziegel, Kalksandstein, Porenbeton und Leichtbeton wurden dabei material- und verfahrenstechnische sowie ökologische, ökonomische und soziale Aspekte berücksichtigt. Auf Grundlage der gewonnenen Erkenntnisse wurde ein EDV-gestütztes Analysetool (Web-Tool) zur Nachhaltigkeitsbewertung für das Mauerwerksrecycling entwickelt. Mit dem Web-Tool sollen Anwender (Planer, Architekten, Recycler) die Möglichkeit erhalten, für verschiedene Untersuchungsfälle unter Einbeziehung regional und sachlich bedingter Parameter, wie Materialqualität, Stoffmengen, Logistik, Aufbereitungstechnik, Anwendungsbereiche, Kosten und Erlöse, objektspezifische Aussagen zur Nachhaltigkeit treffen zu können. Auf diesem Wege können im Sinne der aktuellen gesetzlichen Vorgaben nachhaltige Stoffkreisläufe im Mauerwerksbau geschlossen und somit letztlich die Deponierung von Mauerwerksrestmassen vermieden werden. Alle vier Wandbaustoffarten haben sich im Rahmen des Forschungsvorhabens als recyclingfähig und hinsichtlich der Nachhaltigkeit als gleichwertig erwiesen. Das Ziel des Vorhabens wurde damit erreicht. KW - Nachhaltigkeit KW - Mauerwerkbruch KW - Ganzheitlichkeit PY - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-288572 SP - 1 EP - 182 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-28857 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Spranger, Holger T1 - THz-ToFD Tomography with Synthetic-Aperture-Aperture N2 - Terahertz-radiation (T-ray) are electromagnetic waves within a frequency range between 0,3 to 6 THz. T-rays are nonionising! They penetrate plastic, paper, ceramic and fabric. It is promising to use T-Rays for CT-applications to reveal uncertainties in dielectric materials. T2 - 8. THz-PhD-meeting CY - Marburg, Germany DA - 06.08.2013 KW - Terahertz Tomography synthetic aperture PY - 2013 AN - OPUS4-36223 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sojref, Regine A1 - Schreiber, R. A1 - Makrlik, A. A1 - Schadrack, Reinhard A1 - Müller, Ralf T1 - Fused Silica Containing Powders for Low Sintering (1650°C) Mullite-Zirconia Composites T2 - 23rd International Congress on Glass CY - Prague, Czech Republic DA - 01.07.2013 PY - 2013 AN - OPUS4-30851 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Payton, E. A1 - Nolze, Gert T1 - The Backscatter Electron Signal as an Additional Tool for Phase Segmentation in Electron Backscatter Diffraction N2 - The advent of simultaneous energy dispersive X-ray spectroscopy (EDS) data collection has vastly improved the phase separation capabilities for electron backscatter diffraction (EBSD) mapping. A major problem remains, however, in distinguishing between multiple cubic phases in a specimen, especially when the compositions of the phases are similar or their particle sizes are small because the EDS interaction volume is much larger than that of EBSD, and the EDS spectra collected during spatial mapping are generally noisy due to time limitations and the need to minimize sample drift. The backscatter electron (BSE) signal is very sensitive to the local composition due to its atomic number (Z) dependence. BSE imaging is investigated as a complimentary tool to EDS to assist phase segmentation and identification in EBSD through examination of specimens of meteorite, Cu dross, and steel oxidation layers. The results demonstrate that the simultaneous acquisition of EBSD patterns, EDS spectra, and the BSE signal can provide new potential for advancing multiphase material characterization in the scanning electron microscope. KW - Electron backscatter diffraction KW - Energy dispersive x-ray spectroscopy KW - Scanning electron microscopy KW - Multiphase microstructure KW - Phase identification KW - Backscattered electron imaging KW - Meteorite KW - Monte Carlo simulation PY - 2013 U6 - https://doi.org/10.1017/S1431927613000305 VL - 19 IS - 4 SP - 929 EP - 941 AN - OPUS4-37895 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Epishin, A. A1 - Link, T. A1 - Svetlov, I. L. A1 - Nolze, Gert A1 - Saliwan Neumann, Romeo A1 - Lucas, H. T1 - Mechanism of porosity growth during homogenisation in single crystal nickel-based superalloys N2 - Several mechanisms for porosity growth in single crystal nickel-based superalloys during homogenisation heat treatment have been proposed in the literature. They were carefully checked using different experimental methods, namely quantitative light microscopy, scanning electron microscopy, transmission electron microscopy, X-ray diffraction and density measurements. It is shown that the main mechanism is the Kirkendall–Frenkel effect, i.e. generation of voids due to uncompensated efflux of Al atoms from dissolving γ/γ′-eutectic areas. The Al diffusion is supported by the afflux of vacancies from surrounding γ-matrix which results in porosity growth. This conclusion is confirmed by the estimation of the vacancy afflux towards the dissolving eutectic. KW - Ni-base superalloy KW - Eutectic KW - Vacancies KW - Porosity PY - 2013 VL - 104 IS - 8 SP - 776 EP - 782 PB - Carl Hanser Verlag AN - OPUS4-37983 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Payton, E. J. A1 - Agudo Jácome, Leonardo A1 - Nolze, Gert T1 - Phase Identification by Image Processing of EBSD Patterns N2 - Automated electron backscatter diffraction (EBSD) is generally unable to distinguish between multiple cubic phases in a specimen without additional information, such as that obtained by simultaneous energy dispersive X-ray spectroscopy (EDS). Small particles of phases with relatively similar compositions push the limits of phase identification using simultaneous EBSD and EDS, and a mismatch exists between the spatial resolutions of these two techniques due to them having different electron interaction volumes. In a recent paper, the present authors explored using backscatter detectors mounted on top of the EBSD detector to obtain atomic number (Z) contrast images that could be used for phase segmentation in cases where the results from the EBSD and EDS signals remain ambiguous. In the present work, we show that similar information can be obtained from the raw EBSD patterns themselves at higher spatial resolution than was obtained from the backscatter detectors, with the additional advantage of having no spatial mismatch between the data collection grids. KW - Phase identification KW - Backscattered electrons KW - EBSD KW - SEM PY - 2013 U6 - https://doi.org/10.1017/S143192761300620X VL - 19 IS - Suppl. 2 SP - 842 EP - 843 AN - OPUS4-37985 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Nolze, Gert A1 - Payton, E. A1 - Winkelmann, Aimo T1 - Advanced EBSD Pattern Interpretation through Iterative Post-Processing N2 - Since the BSE signal depends on many factors, like the chemistry of the phase and the acceleration voltage, the size and position of the detector array is (slightly) different from phase to phase so that an (iterative) post-processing of the stored patterns is highly recommended. The derived BSE signal can be used for phase assignment in high resolution and high speed maps when EBSD fails and/or EDS (energy dispersive spectroscopy) needs too much time for a suitable and parallel signal acquisition. KW - Electron backscatter diffraction KW - Phase identification KW - Microstructure KW - SEM PY - 2013 U6 - https://doi.org/10.1017/S1431927613005631 VL - 19 IS - Suppl. 2 SP - 728 EP - 729 AN - OPUS4-37986 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Nolze, Gert T1 - Combination of colored patterns and cubes for crystallographic point group visualization N2 - A concept based on the application of a cube as a general polyhedron is presented for the visualization of point group symmetry. The cube is used to represent both the highest and lowest crystal symmetries, with differences observable as patterns characteristic to each point group. Patterns are generated using direction-specific color keys, which enable the recognition of point group-specific distribution of vectors in an external reference frame. For the visualization of the incoherent hexagonal crystal classes, two twinned cubes are applied in order to generate symmetry operators that would otherwise be missing. The resulting hexagonal dipyramid is described in the frame of a cube, reducing the number of used symmetry operators from 72 to 60. The complete set of 32 polyhedra are suitable, for example, as a visual aid for understanding the crystal symmetry and/or sub- and supergroup relationships. KW - Subgroup KW - Crystal class KW - Color key KW - Fundamental zone KW - Teaching PY - 2013 U6 - https://doi.org/10.1002/crat.201300134 VL - 48 IS - 7 SP - 476 EP - 489 PB - WILEY-VCH AN - OPUS4-37988 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Nolze, Gert T1 - Azimuthal Projections: Data Rotation and Projection Switching in Real Time N2 - Pole figures are often used to present crystal orientation data. The huge number of single orientation measurements acquired by electron backscatter diffraction (EBSD) poses a challenge for pole figure representation due to the large number of calculations required. This significantly reduces the speed at which the data may be rotated and affects the ability to switch between different projection types. In the present work, it will be shown that satisfactory representation of orientation data in different projection types can generally be achieved by an imaging of a spherical projection. With this approach, explicit calculation of the projections is no longer required, allowing for both real-time dataset rotation and real-time switching between all projection types relevant to materials science. The technique can be applied to any other directional property distribution, for example, not only for EBSD orientation presentation. KW - Stereographic projection KW - Equal area projection KW - Gnomonic projection KW - Azimuthal projection KW - Crystal orientation KW - Projection imaging KW - Coordinate transformation KW - Real-time rotation PY - 2013 U6 - https://doi.org/10.1017/S1431927613001414 VL - 19 SP - 950 EP - 958 PB - Microscopy Society of America AN - OPUS4-37989 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Nolze, Gert A1 - Payton, E. T1 - Messengers from Space: A Scanning Electron Microscopy Investigation N2 - The macro- and microstructure of iron meteorites provide valuable insights into both the inner structure of our planet and the history of our solar system. High speed collision events in the asteroid belt send the meteorites careening toward Earth. The collisions produce unique deformation microstructures. With cooling rates on the scale of a few degrees per million years, iron meteorites can consist of crystal sizes on the order of meters prior to the collision events. These extremely slow cooling rates result in phase transformations occurring at conditions near thermodynamic equilibrium. Preserving meteorite fragments is important for future studies of phase transformations, material behavior at high strain rates, and the origin of the universe. KW - Meteorite KW - Phase identification KW - Hibbingite KW - Orientation relationship KW - Electron backscatter diffraction KW - Energy dispersive x-ray spectroscopy KW - EDX PY - 2013 IS - 3 SP - 2 EP - 4 PB - GIT Verlag AN - OPUS4-37981 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vasilic, Ksenija A1 - Schmidt, Wolfram A1 - Kühne, Hans-Carsten A1 - Roussel, N. T1 - Model of SCC flow through reinforced sections: experimental validation N2 - This study focuses on concrete flow in presence of obstacles and develops a mathematical model and a computational approach for SCC flow through reinforced formworks. In order to decrease high computational times needed to simulate castings through reinforced elements, an innovative approach to model the reinforced sections as porous media is proposed here. In the previous work, this numerical model is proved able to simulate the free-surface flow of non-Newtonian fluids through the reinforcement networks. In the present study, the applicability of the model on the concrete flow will finally be proved. The large-scale form-filling experiments with SCC will be conducted and the experiments will be simulated using the proposed numerical model. The numerical model will then be validated through the comparison of the experimental results and the results of the numerical simulations. T2 - 7th RILEM International Conference on Self-Compacting Concrete and 1st RILEM International Conference on Rheology and Processing of Construction Materials CY - Paris, France DA - 02.09.2013 KW - Porous medium KW - Rheology KW - Numerical modelling KW - Reinforcement PY - 2013 SN - 978-2-35158-137-7 SN - 978-2-35158-138-4 SP - 229 EP - 236 PB - RILEM Publishing S.A.R.L CY - Paris, France AN - OPUS4-37442 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Elabshihy, Karim A1 - Kalinka, Gerhard T1 - Investigation of the time-dependent behavior of cnt-filled epoxy using nanoindentation N2 - Epoxy/Carbon nanotube (CNT) composites are interesting materials that could be used in a wide variety of applications. In this study, CNT contents of 0.25, 0.5, 1 and 2 wt% were used for reinforcing epoxy. A nanoindentation device and a temperature regulating system were developed in order to investigate the effect of CNTs on the time-dependent properties of epoxy using relaxations and creep tests on the nano scale. The relaxation tests showed a significant shift for the relaxation spectrum towards shorter times with introducing a low CNT content of 0.25 wt%. Additionally, creep tests showed that both the holding time at a constant load and the unloading velocity have a major effect on the contact stiffness. However, there was no effect for the CNTs on the creep behavior with contents lower than 1 wt%, which was related to the presence of a percolation threshold around this value. T2 - Nanobrücken 2013 CY - Dresden, Germany DA - 20.03.2013 KW - Epoxy KW - CNT KW - Time-dependent KW - Nanoindentation PY - 2013 AN - OPUS4-35533 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schröter, Maria-Astrid A1 - Sturm, Heinz A1 - Holschneider, M. T1 - Phase and amplitude patterns in DySEM mappings of vibrating microstructures N2 - We use a dynamic scanning electron microscope (DySEM) to analyze the movement of oscillating micromechanical structures. A dynamic secondary electron (SE) signal is recorded and correlated to the oscillatory excitation of scanning force microscope (SFM) cantilever by means of lock-in amplifiers. We show, how the relative phase of the oscillations modulate the resulting real part and phase pictures of the DySEM mapping. This can be used to obtain information about the underlying oscillatory dynamics. We apply the theory to the case of a cantilever in oscillation, driven at different flexural and torsional resonance modes. This is an extension of a recent work (Schr¨oter et al 2012 Nanotechnology 23 435501), where we reported on a general methodology to distinguish nonlinear features caused by the Imaging process from those caused by cantilever motion. KW - DySEM KW - mechanical nonlinearity KW - vibration KW - DySEM KW - mechanische Nichtlinearitäten KW - Vibration PY - 2013 U6 - https://doi.org/doi:10.1088/0957-4484/24/21/215701 VL - 24 IS - 21 SP - 215701-1 EP - 215701-10 PB - IOP PUBLISHING LTD CY - Bristol, UK AN - OPUS4-35396 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gebhardt, M.O. A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael T1 - Numerical analysis of hot cracking in laser-hybrid welded tubes N2 - In welding experiments conducted on heavy wall pipes, the penetration mode (full or partial penetration) occurred to be a significant factor influencing appearance of solidification cracks. To explain the observed phenomena and support further optimization of manufacturing processes, a computational model was developed, which used a sophisticated strategy to model the material. High stresses emerged in the models in regions which showed cracking during experiments. In partial penetration welding, they were caused by the prevention of weld shrinkage due to the cold and strong material below the joint. Another identified factor having an influence on high stress localization is bulging of the weld. PY - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-302961 SN - 1687-8442 SN - 1687-8434 IS - Article ID 520786 SP - 1 EP - 8 PB - Hindawi Publishing Corporation CY - New York, NY, USA AN - OPUS4-30296 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Liu, X. C. A1 - Wu, Chuan Song A1 - Rethmeier, Michael A1 - Pittner, Andreas T1 - Mechanical properties of 2024-T4 aluminium alloy joints in ultrasonic vibration enhanced friction stir welding N2 - Ultrasonic vibration enhanced friction stir welding (UVeFSW) is a recent modification of conventional friction stir welding (FSW), which transmits ultrasonic vibration directly into the localized area of the workpiece near and ahead of the rotating tool. In this study, a high strength aluminium alloy (2024-T4) was welded by this process and conventional FSW, respectively. Then tensile tests, microhardness tests and fracture surface analysis were performed successively on the welding samples. The tests results reveal that ultrasonic vibration can improve the tensile strength and the elongation of welded joints. The microhardness of the stir zone also increases. KW - Ultrasonic vibration KW - Friction stir welding KW - Mechanical properties PY - 2013 UR - https://www.researchgate.net/publication/286735810_Mechanical_properties_of_2024-T4_aluminium_alloy_joints_in_ultrasonic_vibration_enhanced_friction_stir_welding VL - 22 IS - 4 SP - 8 EP - 13 AN - OPUS4-40773 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Brosig, Laura A1 - Horn, Wolfgang A1 - Pyza, Lars A1 - Jann, Oliver A1 - Plehn, W. T1 - Round robin test for the implementation of odour measurements according to DIN ISO 16000-28 into the assessment of emissions from building products N2 - Odour measurements become increasingly important in view of the assessment of indoor air quality and the emissions of building products. Hence they need to be implemented into evaluation schemes such as the AgBB scheme. While there are already standards like DIN ISO 16000-28 and VDI 4302 Part 1 specifying the procedure of odour measurements using a comparison scale, no final validation of the method has been carried out so far. Therefore, a round robin test was conducted in 2012 with 12 participating laboratories that mainly consisted of the following two parts: 1) testing of the available comparison scales with respect to their operational performance and 2) execution of an odour assessment of an acrylic sealant using emission test chambers. Part one included the measurement of the air flow rates and the provided concentrations of the reference substance (acetone). Part two was conducted to test the performance of the laboratories and the applicability of DIN ISO 16000-28 and supplementary VDI 4302 Part 1 by assessing the perceived intensity and the hedonic tone of the air samples. Moreover, samples for VOC analysis were taken from the air in the emission test chamber on the 7th day of testing to allow for quality control. Resulting from this round robin test main deficits were detected and suggestions for the improvement of the odour measurement procedure were made. N2 - Im Rahmen der Bewertung von Innenraumluftqualität und von Emissionen aus Bauprodukten gewinnt auch die Beurteilung entstehender Gerüche zunehmend an Bedeutung. Um der daraus resultierenden Forderung nach Geruchsbewertungen gerecht zu werden, müssen entsprechende Methoden in bestehende Bewertungssysteme, wie z. B. das AgBB-Schema, aufgenommen werden. Als Grundlage hierfür bieten sich die bereits bestehenden Regelwerke DIN ISO 16000-28 und VDI 4302 Blatt 1 an, die das Vorgehen bei Geruchsmessungen unter Verwendung eines Vergleichsmaßstabes vorgeben. Da für die beschriebene Methode bisher keine Validierung vorliegt, wurde 2012 ein Ringversuch mit zwölf Instituten durchgeführt, der sich hauptsächlich aus zwei Teilen zusammensetzte: 1) Überprüfung der technischen Funktionsfähigkeit der verwendeten Vergleichsmaßstäbe und 2) Durchführung einer Geruchsbewertung für eine Acryldichtmasse mithilfe von Emissionsprüfkammern. Im ersten Teil wurden sowohl die Volumenströme als auch die bereitgestellten Konzentrationen der Referenzsubstanz Aceton bestimmt. Der zweite Teil diente neben der Ermittlung der Leistungsfähigkeit der Laboratorien vor allem der Feststellung, inwieweit eine Bestimmung der empfundenen Intensität und der Hedonik nach DIN ISO 16000-28, ergänzt durch VDI 4302 Blatt 1, einheitlich möglich ist. Aus Gründen der Vergleichbarkeit und der Qualitätskontrolle wurden am siebten Tag der Messungen zusätzlich Proben der Prüfkammerluft zur VOC-Bestimmung genommen. Mithilfe des Ringversuchs konnten Defizite sowohl technischer als auch methodischer Art festgestellt und Vorschläge für die Verbesserung des Vorgehens bei Geruchsbewertungen erarbeitet werden. PY - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-293110 UR - http://www.gefahrstoffe.de/gest/article.php?data[article_id]=75118 SN - 0949-8036 SN - 0039-0771 SN - 1436-4891 VL - 73 IS - 10 SP - 441 EP - 445 PB - Springer-VDI-Verlag CY - Düsseldorf AN - OPUS4-29311 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pech, Anja A1 - Wilke, Olaf A1 - Mull, Birte A1 - Horn, Wolfgang A1 - Jann, Oliver T1 - Development of a TDS-GC-FID method for the determination of methanol and ethanol in air N2 - A method for the determination of very volatile organic compounds (VVOC) in air was developed and successfully tested for methanol and ethanol. Carbotrap300® (a multi-bed tube using Carbopack C®, Carbopack B® and Carbosive SIII®) was selected as sorption material for thermal desorption and tested for its suitability for emission test chamber measurements. The adsorption behaviour and the chromatographic results are influenced negatively by spiking aqueous solutions on the adsorption medium for calibration purposes. The latter effect can be reduced by blowing dry air across the adsorbent to remove the adsorbed water. Detection and quantification limits were determined for a GC-FID system and compared to GC-MS. The applicability of the method was tested with a methanol eliminating silane modified polymeric adhesive (SMP-adhesive for parquet) in an emission test chamber N2 - Eine Methode zur Bestimmung von sehr leicht flüchtigen Verbindungen in Luft wurde für Methanol und Ethanol entwickelt und erfolgreich getestet. Dafür wurde Carbotrap300® (Multibettrohr aus Carbopack C®, Carbopack B® und Carbosive SIII®) als Sorptionsmedium für die Thermodesorption ausgewählt und dessen Eignung für Emissionskammermessungen untersucht. Das Adsorptionsverhalten und die chromatographischen Ergebnisse werden negativ durch die Aufgabe von wässrigen Kalibrierlösungen auf das Adsorptionsmedium beeinflusst. Durch das Überleiten von trockener Luft kann dieser Effekt verringert werden, da so das adsorbierte Wasser entfernt wird. Die Nachweis- und Bestimmungsgrenzen wurden für ein eingesetztes GC- FID-System ermittelt und mit einem GC-MS verglichen. Mit einem methanolabspaltenden silanmodifizierten Polymerklebstoff (SMP-Parkettkleber), der in eine Emissionskammer eingebracht wurde, konnte die Tauglichkeit der Methode überprüft werden. PY - 2013 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-297020 UR - http://www.gefahrstoffe.de/gest/article.php?data[article_id]=76019 SN - 0949-8036 SN - 0039-0771 SN - 1436-4891 VL - 73 IS - 11/12 SP - 477 EP - 482 PB - Springer-VDI-Verlag CY - Düsseldorf AN - OPUS4-29702 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bettge, Dirk A1 - Bohraus, Stephan A1 - Schmidt, Rüdiger A1 - Portella, Pedro Dolabella T1 - Aufbau einer fraktographischen Online-Datenbank N2 - Fraktographischen Daten aus Schadensanalysen, Vergleichsversuchen und Vorhaben könnten der Fachöffentlichkeit im Bereich Fraktographie zur Verfügung gestellt werden, sofern das Urheber-recht es zulässt und außerdem ein geeignetes Medium existiert. Ein solches Medium könnte eine offene fraktographische online-Datenbank sein. Eine solche wird im Rahmen der AG Fraktographie im DVM-DGM Gemeinschaftsausschuss "Rasterelektronenmikroskopie in der Materialprüfung" zurzeit erarbeitet. T2 - Metallographietagung 2013 CY - Friedrichshafen, Germany DA - 18.09.2013 KW - Datenbank KW - Fraktographie KW - Schadensanalyse PY - 2013 AN - OPUS4-50597 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bettge, Dirk A1 - Bohraus, Stephan A1 - Schmidt, Rüdiger A1 - Portella, Pedro Dolabella ED - Lohrmann, M. ED - Rettenmayr, P. T1 - Aufbau einer fraktographischen online-Datenbank N2 - Fraktographischen Daten aus Schadensanalysen, Vergleichsversuchen und Vorhaben könnten der Fachöffentlichkeit im Bereich Fraktographie zur Verfügung gestellt werden, sofern das Urheberrecht es zulässt und außerdem ein geeignetes Medium existiert. Ein solches Medium könnte eine offene fraktographische online-Datenbank sein. Eine solche wird im Rahmen der AG Fraktographie im DVM-DGM Gemeinschaftsausschuss "Rasterelektronenmikroskopie in der Materialprüfung" zurzeit erarbeitet. T2 - Metallographietagung 2013 CY - Friedrichshafen, Germany DA - 18.09.2013 KW - Datenbank KW - Fraktographie KW - Schadensanalyse PY - 2013 SN - 978-3-88355-398-6 VL - 45 SP - 19 EP - 24 PB - Inventum CY - Bonn AN - OPUS4-50598 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -