TY - CONF A1 - Léonard, Fabien T1 - CT for additive manufacturing process characterisation: assessment of melt strategies on defect population N2 - Selective Electron Beam Melting (SEBM) is a promising powder bed Additive Manufacturing (AM) technique for near net-shape manufacturing of high-value titanium components. However, as with every emerging technique, the manufacturing processes can still be greatly improved and optimised. In particular, the links between AM settings and the resulting sample porosity is of great interest, as the fatigue life of SEBM parts is currently dominated by the presence of porosity. In this study, the size, volume fraction, and spatial distribution of the pores in model samples have been characterised in 3D, using X-ray Computed Tomography (CT), and correlated to the SEBM process variables. A strong relationship was found with the different beam strategies used to contour, and infill by hatching, a part section. The majority of pores were found to be small spherical gas pores, concentrated in the infill hatched region. Rarer irregular shaped pores were mostly located in the contour region and have been attributed to a lack of fusion between powder particles. T2 - Conference on Industrial Computed Tomography iCT2016 CY - Wels, Austria DA - 09.02.2016 KW - Titanium KW - Additive Manufacture KW - Selective Electron Beam Melting KW - Pores KW - Defects KW - X-ray Computed Tomography PY - 2016 AN - OPUS4-39186 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kabelitz, Anke T1 - Time resolved WAXS studies on the crystallization of Al13 keggin clusters N2 - We report on the in situ investigation of the Al13 sulfate synthesis by WAXS. Al13 sulfates were crystallized by precipitating hydrolyzed aluminum solutions by the addition of sodium sulfate. The measurements were performed using an acoustic levitator. The study provides information about the intermediates during the crystallization process. T2 - Eighth Joint BER II and BESSY II User Meeting CY - Berlin, Germany DA - 07.12.2016 KW - In situ KW - Crystallization KW - WAXS PY - 2016 AN - OPUS4-39365 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Becker, Ben T1 - Aging of composite pressure cylinder (COD-AGE) N2 - Subject, Aim and methods within the Project COD-AGE. Test methods and condition monitoring for Composite-cylinders T2 - Follow-up Workshop on statistical safety assessment CY - Berlin, Germany DA - 05.10.2016 KW - Aging KW - Composite cylinder KW - Non destructive testing PY - 2016 AN - OPUS4-39087 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - John, Sebastian T1 - Lebensdauerabschätzung von Composite-Druckgefäßen / COD-AGE N2 - Ermittlung von Kennwerten und Modelbildung zur Lebensdauerabschätzung von Composite-Druckgefäßen. T2 - 3. Workshop Themenfeld Material CY - Berlin, Germany DA - 12.10.2016 KW - Composite-Druckgefäße KW - Lebensdauer KW - FEM KW - Bruchmechanik PY - 2016 AN - OPUS4-39090 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rosemann, Paul T1 - Einfluss der Oberflächennachbearbeitung auf die Korrosionsbeständigkeit von Schweiß-nähten des Duplexstahls 1.4062 N2 - Die Korrosionsbeständigkeit geschweißter Konstruktionen aus nichtrostenden Duplexstählen wird von den Schweißparametern und der Nachbehandlung der Oberflächen bestimmt. Eine etablierte Methode der Schweißnahtnachbehandlung ist das Strahlen der Oberfläche mit Glasperlen. Diese Methode soll aus wirtschaftlichen Gründen durch das Strahlen mit Korund ersetzt werden, welches deutliche Zeit- und Kostenvorteile bietet. Besonders bei der Lochkorrosionsbeständigkeit hat sich das Schleifen mit Korund bereits als nachteilig erwiesen, weshalb diese Umstellung auch beim Stahlen kritisch hinterfragt wird. Daher wurden Probeschweißungen bei der Firma Modersohn hergestellt und mit verschiedenen Oberflächenbearbeitungsmethoden (Glasperlenstrahlen, Korundstrahlen, Beizen, Elektropolieren, Schleifen) nachbehandelt. Diese verschiedenen Oberflächenzustände wurden analytisch (REM, Rauheit) charakterisiert und hinsichtlich ihrer Lochkorrosionsbeständigkeit vergleichend untersucht werden, um die Eignung des Strahlens mit Korund zu beurteilen. T2 - GfKORR-Jahrestagung 'Duplex-Stähle – Nische oder Zukunft ?' CY - Frankfurt/M., Germany DA - 15.11.2016 KW - Korrosionsbeständigkeit KW - Schweißnähte KW - Duplexstahl PY - 2016 AN - OPUS4-39470 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rosemann, Paul A1 - Kauss, Norman T1 - Einfluss des Schwefelgehalts auf die Korrosionsbeständigkeit des nichtrostenden Stahls 1.4404 N2 - Die Korrosionsbeständigkeit nichtrostender Stähle wird maßgeblich von ihrer chemischen Zusammensetzung bestimmt. Der tendenzielle Einfluss ist für die Hauptlegierungselemente in der wissenschaftlichen Fachliteratur beschrieben. Bei Begleitelement Schwefel gibt es dagegen keine konkreten Untersuchungen die belegen, ab welchem Gehalt mit einer Verringerung der Korrosionsbeständigkeit zu rechnen ist. Im Lichtbogenschmelzofen wurden verschiedene Legierungen mit abgestuftem Schwefelgehalten hergestellt, um den Einfluss dieses Begleitelementes auf die Korrosionsbeständigkeit systematisch zu untersuchen. Die KorroPad-Prüfung und die Bestimmung kritischer Lochkorrosionspotentiale wurden zur Charakterisierung der Legierungen genutzt. Beide Methoden belegen eine zunehmende Verringerung der Lochkorrosionsbeständigkeit mit dem Schwefelgehalt. T2 - GfKORR-Jahrestagung 'Duplex-Stähle – Nische oder Zukunft ? CY - Frankfurt/M., Germany DA - 15.11.2016 KW - Schwefelgehalt KW - Korrosionsbeständigkeit KW - Nichtrostender Stahl PY - 2016 AN - OPUS4-39472 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, C. T1 - Einfluss der Abkühlgeschwindigkeit auf die Korrosionsbeständigkeit martensitischer nichtrostender Stähle N2 - Martensitische nichtrostende Stähle werden in verschiedenen technischen Bereichen eingesetzt, bei denen eine optimale Kombination aus hoher mechanischer Festigkeit und guter korrosiver Beständigkeit gefordert wird. Beide Eigenschaften werden in der Industrie primär durch die Wärmebehandlung gesteuert. Die Korrosionseigenschaften sind dabei stark von der diffusionsbedingten Bildung und Auflösung von Chromkarbiden abhängig. In vergangenen wissenschaftlichen Arbeiten konnte nachgewiesen werden, dass die Abkühlgeschwindigkeit nach dem Austenitisieren einen großen Einfluss auf die Bildung solcher Karbide hat. Der Einfluss der Abkühlgeschwindigkeit auf die Lochkorrosionsbeständigkeit wurde an den Stählen 1.4108 und 1.4116 systematisch untersucht. Mit Hilfe des Stirnabschreckversuches wurde dabei die Abkühlgeschwindigkeiten variiert und anschließend die Veränderung von Gefüge, Lochkorrosionsbeständigkeit und Härte untersucht. Als Ergebnis konnten kritische Abkühlgeschwindigkeiten ermittelt werden, bei denen eine kritische Verringerung der Korrosionsbeständigkeit einsetzt. T2 - GfKORR-Jahrestagung 'Duplex-Stähle – Nische oder Zukunft ?' CY - Frankfurt/M., Germany DA - 15.11.2016 KW - Korrosionsbeständigkeit KW - Martensitische nichtrostende Stähle KW - Abkühlgeschwindigkeit PY - 2016 AN - OPUS4-39473 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wu, Cheng-Chieh T1 - Determination of an approximate anisotropic model for a given geometrical complex isotropic structure by means of finite element method and least-squares adjustment N2 - Many engineering structures are made of composite materials or metal foam. To simulate the deformational behaviour of these structures often requires a high number of discretisation elements. This in turn yields a very large system of linear equations that are extremely time and memory consuming or practically impossible to solve. It is therefore desirable to find an approach to overcome this obstacle. T2 - PhD Day 2016 CY - Berlin, Germany DA - 01.09.2016 KW - Least-Squares Adjustment KW - Inverse Analysis KW - Finite Element Method PY - 2016 AN - OPUS4-37521 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wu, Cheng-Chieh T1 - Approximate model for geometrical complex structures N2 - Many engineering structures are made of composite materials or metal foam. To simulate the deformational behaviour of these structures often requires a high number of discretisation elements. This in turn yields a very large system of linear equations that are extremely time and memory consuming or practically impossible to solve. It is therefore desirable to find an approach to overcome this obstacle. T2 - 33rd Danubia- Adria Symposium on Advances in Experimental Mechanics CY - Portorož, Slovenia DA - 20.09.2016 KW - Inverse analysis KW - Finite element method KW - Least-squares adjustment PY - 2016 AN - OPUS4-37523 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Madkour, Sherif T1 - Dielectric investigations on carbon nanomembranes N2 - Multilayer carbon nanomembrances (CNMs) could pave the way for a new ultrathin functional conductive coatings with tunable electrical, optical, and chemical properties. Due to their molecular thickness, they can also be regarded as “interfaces without bulk” separating regions of different gaseous, liquid, or solid components and controlling the materials exchange between them, making them optimal materials for membranes applications. Furthermore, their physical and chemical properties depend strongly on their structure, molecular composition, and the surroundings of either sides, thus allowing for tailored properties. Here, nanolayers of Aromatic p-terphenylthiol (TPT) self-assembled into 2D carbon monolayers (thickness - 1.6 nm) were synthesized and further crosslinked by ion bombardment, forming CNMs. Here, though a recently developed multilayer nanosheets routine, stacks of 5, 10, 15 and 20 TPT sheets where transferred on top of each other forming a multilayered CNMs. However, this transfer routine could introduce some intrinsic defects to the sheets, which would alter the molecular composition and / or structure, thus consequently the CNMs properties. Therefore, it is essential to characterize defects in “pure” TPT nanomembranes, before tailoring the molecular compositions, e.g. adding functional groups. For this reason, broadband dielectric spectroscopy (BDS) was utilized to characterize any defects that could be rasied during preparation. Due the structure of pure TPT membranes, no dipole moment should exsist. However, the presence of other elements, e.g. water or sulphur, would result in a dipole moment that could be probed by BDS. As a main result, for all different stacked-layer numbers, a clear relaxation process is seen, which moves to higher frequencies with increasing the temperature. The temperature dependence of the relaxation rate of this process is independent of film thickness and can be well described by a common VFT function, hence a corporative motion. This relaxation process was assigned to intrinisic defects in the membranes, introduced during preparation, which was further confimed by a detailed anaylsis of the dielectric strength. This is the first BDS measurment on TPT CNMs. T2 - 9th International Conference on Broadband Dielectric Spectroscopy and its Applications CY - Pisa, Italy DA - 11.09.2016 KW - Carbon nanomembranes PY - 2016 AN - OPUS4-37527 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Sebastian Hanns-Otto T1 - Wide-spectrum dielectric functions of ALD deposited oxides relevant for photovoltaics N2 - Silicon surface passivation with atomic layer deposited (ALD) thin films has gained more and more interest in the PV community in recent years. With ALD good film quality, accurate thickness control and conformity are reached. Furthermore, ALD is capable of coating difficult substrates such as nanostructured surfaces with the same accuracy as flat surfaces. A variety of materials such as Al2O3, TiO2 and HfO2 demonstrate good surface passivation quality both for front and rear surface of silicon solar cells. In addition of providing good surface passivation, thin films with high refractive index e.g. HfO2, TiO2 and AlN can act simultaneously as antireflection coatings when applied on the front surface of the device. Hence, ALD thin films can reduce both electrical and reflective losses in solar cells. Thorough investigation of the optical properties of these layers is crucial for several reasons related to their production and use. Optical measurements provide a fast, easy, non-destructive, and in situ capable approach to quality assurance for photovoltaic devices. As the function of the final device is optical, optimisation of the device performance relies strongly on the knowledge of the wide-range dielectric function of the thin layers. In this contribution, we determined the optical constants of ALD generated layers of AlN, Al2O3, TiO2, and HfO2 in a wide spectral range covering the near ultraviolet and the mid-infrared regions by means of spectroscopic ellipsometry. By combining data from a UV-Vis-NIR ellipsometer (Woollam M2000DI) and an FTIR ellipsometer (Sentech Sendira), we can determine the optical constants alongside with the layer thicknesses from one large set of spectroscopic measurements. We consider this a contribution to the metrological treatment of stratified and structured thin films in the optical range by polarisation-sensitive measurement methods. T2 - International conference on spectroscopic ellipsometry (ICSE 7) CY - Berlin, Germany DA - 06.06.2016 KW - ALD (atomic layer deposited) KW - Ellipsometry KW - Photovoltaic KW - Solar Cell KW - HfO2 KW - Aln KW - Al2O3 KW - TiO2 PY - 2016 AN - OPUS4-37222 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kotschate, Daniel T1 - Reference block design for high resolution ultrasound immersion tank N2 - In respect of modern approaches in material sciences and highly increased requirements on materials on safety relevant components, quality management and non-destructive testing reclaims a steadily increased meaning. The destructive meaning of measuring the degree of purity is defined in DIN EN 10247 through metallurgical investigations, especially microsections. For and comparable, but non-destructive testing due ultrasonic testing, the material the SEP 1927 is a well-defined industry standard. A novel and alternative way of reference block construction was focused by this work. The proposed amendments, regarding the manufactoring and machining, are less time and cost consuming. Verified by measurements the presented reference block fits the same acoustical characteristics and the requirements of the guideline. T2 - World Conference on Non-Destructive Testing CY - Munich, Germany DA - 13.06.2016 KW - Immersion tank testing KW - SEP 1927 KW - Degree of purity KW - High resolution ultrasonic testing PY - 2016 AN - OPUS4-36850 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erdmann, Maren T1 - Diesel and biodiesel induced degradation of polyethylene N2 - Renewable resources become more and more relevant to maintain energy demands for an increasing global population. Biosynthetic fuels like biodiesel might replace conventional petrochemical fuels, such as diesel. However, more research is needed to characterize the interaction between the different fuels and the polymeric material, especially with respect to ageing and degradation. The poster will present several interaction and degradation phenomena of high density polyethylene (PE-HD) induced by diesel and biodiesel 1-3. Also the possible influence of microbial growth (fungi and bacteria) is considered. The chosen PE-HDs are typical thermoplastic resins for container and storage tank applications. Degradation of PE-HD will be investigated by changes of the mechanical properties – with main emphasis on the Charpy impact strength 2. Furthermore, with alternating sorption and desorption cycles in combination with oven ageing the co-oxidation 3 of PE-HD in contact with biodiesel will be addressed. T2 - MoDeSt 2016 CY - Cracow, Poland DA - 04.09.2016 KW - Impact strength KW - PE-HD KW - Diesel KW - Biodiesel KW - Degradation PY - 2016 AN - OPUS4-37320 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Duffner, Eric T1 - Hydraulic load cycle test bench for extreme temerature tests N2 - Components, function and technical details of the hydraulic load cycle test bench for extreme temperature test. T2 - Hannover Industrie Fair CY - Hannover, Germany DA - 25.04.2016 KW - extreme temperature KW - life cycle test KW - cylinders PY - 2016 AN - OPUS4-37251 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Duffner, Eric T1 - Hydraulic slow burst test bench N2 - Components, function and technical details of the Hydraulic slow burst test bench T2 - Hannover Industrie Fair CY - Hannover, Germany DA - 25.04.2016 KW - cylinders KW - burst test KW - creep behaviour PY - 2016 AN - OPUS4-37252 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Konnertz, Nora T1 - QCM System for the Characterization of Gas Sorption and Physical Aging of Membrane Polymers for Gas Separation Applications N2 - Polymers are favorable materials for gas separation membranes. In general, gas transport experiments are performed with films in the range of 100 µm thickness. However, in large-scale processes very thin selective polymer layers in the range of 100 nm to 1 µm are used. Moreover, it was shown that thin films behave different compared to thick films with respect to gas transport properties and physical aging as well. Thus, for fundamental research it is important to realize gas transport experiments with thin films. The Quartz Crystal Microbalance (QCM) is a very sensitive method to detect mass changes in the range of nanograms. Therefore, this method enables sorption experiments with thin films or layers attached to the QCM crystal (100 nm up to 1 µm). Here, we present the experimental set-up for using the QCM technique for characterizing the gas sorption behavior of thin polymer films in a temperature controlled pressurized environment (up to 50 bar) - also quartz crystals and crystal holders were optimized. The study aims for the characterization of long-term behavior and physical aging of high-performance polymers for gas separation membranes - such as polyimides and polymers of intrinsic microporosity (PIMs) and respective nanocomposites. Especially the differences of the behavior of thin films compared to films with thicknesses up to 100 µm as well as nanofiller induced-effects are adressed. T2 - Polydays 2016 CY - Potsdam, Germany DA - 28.09.2016 KW - Quartz Crystal Microbalance QCM KW - Thin Films; KW - Gas Sorption KW - High Pressure PY - 2016 AN - OPUS4-37911 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sieber, Sarah T1 - Image denoising of ultrasonic echo data acquired on concrete N2 - Ultrasonic echo testing has become a common method in civil engineering for the investigation of concrete structures. The detection of inhomogeneities, reinforcing elements and the geometry of the object is required for quality assurance and Inspection. This assessment depends on the quality of ultrasonic images which can be improved by using Reverse Time Migration (RTM) rather than the standard method, Synthetic Aperture Focusing Technique (SAFT). Although RTM provides a better mapping of circular objects and (dipping) reflectors, the image is corrupted by migration noise. To suppress the image noise, we have tested various filter methods in the spatial domain, frequency domain as well as in the curvelet domain on ultrasonic RTM images. We found that either a spatial edge detection filter in combination with a lowpass filter (Laplacian of Gaussian filter) or two lowpass filter with different filter parameters (Difference of Gaussian filter) removed artefacts. An additional smoothing was obtained by applying the first generation curvelet transform after downsampling the image matrix and adding Gaussian noise. The proposed filter scheme is able to suppress RTM noise and enhance the image quality such that the objective interpretation of ultrasonic images for Quality assessment of concrete specimen is simplified. T2 - 76. Jahrestagung der Deutschen Geophysikalischen Gesellschaft CY - Münster, Germany DA - 14.03.2016 KW - Ultrasonic echo technique KW - Reverse-time migration KW - Image Denoising KW - Curvelet Transform PY - 2016 AN - OPUS4-35839 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Munzke, Dorit T1 - Zustandsüberwachung von Composite-Druckgefäßen mit faseroptischer Sensorik N2 - Funktionsweise, Integration und Messergebnisse von opt. Fasern zur Zustandsüberwachung von Composite-Druckgefäßen. T2 - 3. Workshop Themenfeld Material CY - Berlin, Germany DA - 12.10.2016 KW - Faseroptik KW - Zustandsüberwachung KW - Composite-Druckgefäße PY - 2016 AN - OPUS4-39097 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Ralf T1 - High-temperature laser profilometry N2 - Advanced methods for 3D green density characterization like computed tomography and 3D FE sinter modeling can be utilized for increasing the reliability of sintered components. The experimental in situ observation of sintering, however, is currently restricted to silhouette methods, i.e. heating microscopy. For complex shaped samples, in situ shape screening during shrinkage would allow much better validation of 3D sinter simulation models. Further, by revealing temporary sinter warpage, 3D high-temperature shape screening allows to locate potential defects of complex sintered components. Against this background, BAM developed a testing device for in situ 3D high-temperature shape screening for ceramic and glass-ceramic tapes up to 1000°C [1-3]. Current work is focused on dropping this restriction in sample shape and temperature. The poster illustrates the current state of this work and possible applications of the method e.g. in detecting sinter warpage of metallized glass-ceramic LTCC tapes. T2 - SGT Centenary Conference, & ESG 2016 CY - Sheffield, UK DA - 04. 09. 2016 KW - Laser profilometry KW - 3D High-temperature shape screening KW - Sintering PY - 2016 AN - OPUS4-38320 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Konnertz, Nora T1 - Enhanced gas separation performance of nanocomposites based on a polymer with intrinsic microporosity PIM-1 and phenethyl-POSS N2 - In times of the energy revolution, the need for energy efficient separation processes promotes the advancement of new high performance materials for use as highly selective separation membranes. Most promising materials in this field, especially for gas separation, are polymers with intrinsic microporosity (PIMs) which were firstly introduced by Budd and McKeown. In this study the permeability of PIM-1 was increased by 439 % by formation of nanocomposites with only 1 wt% of polyhedral oligomeric phenethyl-silsesquioxane (PhE-POSS) within the polymer matrix. As the CO2/CH4 selectivity is fully retained, this leads to a shift in the Robeson plot towards the upper bound. The Robeson plot describes the current state of the art trade-off relation between selectivity and permeability of all known membrane polymers. As molecular mobility is a key factor for gas transport as well as the often observed physical aging of such polymers, our study also includes for the first time, molecular dynamics and conductivity of pure PIM-1 and PIM-1 nanocomposites as investigated by broadband dielectric spectroscopy (BDS). T2 - Polydays 2016 CY - Potsdam, Germany DA - 28.09.2016 KW - PIM-1 KW - POSS KW - Broadband dielectric spectroscopy KW - Permeation PY - 2016 AN - OPUS4-37701 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weise, Frank T1 - Influence of aggregate size on the damage potential of alkal-silica-reaction N2 - The poster shows new results on Alkali-Silica-Reaction (a damage mechanism of concrete). The influence of the aggregate size in the sand fraction is investigated, revealing that different types of aggregate behave in a different way. T2 - 15th International Conference of Alkali Aggregate Reaction in Concrete (ICAAR 2016) CY - Sao Paulo, Brazil DA - 03.07.2016 KW - Alkali-silica-reaction KW - Building materials KW - Concrete KW - Durability PY - 2016 AN - OPUS4-36951 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Epperlein, Nadja T1 - Influence of femtosecond laser produced nanostructures on biofilm growth on steel N2 - Large area periodic surface structures were generated on steel surfaces using 30-fs laser pulses at 790 nm wavelength. Two types of steel exhibiting a different corrosion resistance were used, i.e. a plain structural steel (corrodible) and a stainless steel (resistant to corrosion). Homogeneous fields of laser-induced periodic surface structures (LIPSS) were realized utilizing laser fluences close to the ablation threshold while scanning the sample under the focused laser beam in a multi-pulse regime. The nanostructures were characterized with optical and scanning electron microscopy. For each type of steel, more than ten dentical samples were laser-processed. These samples were subjected to microbial adhesion tests, investigating bacterial adhesion behavior on the laser structures in comparison to polished reference surfaces. Short term experiments (<24h) were carried out to determine initial biofilm development. E. coli as a typical bacterium representing pathogenic bacteria and Shewanella putrefaciens as metal corrosive bacterium were used for biofilm development analyses. Bacterial cell adhesion was determined microscopically after DAPI cell staining (DNA staining). Comparison of the coverage areas between nanostructured and polished surfaces revealed differences in cell adhesion behavior and biofilm structure. T2 - E-MRS 2016 Spring Meeting, Symposium C: "Laser-material interactions for tailoring future applications" CY - Lille, France DA - 02.05.2016 KW - Laser-induced periodic surface structures (LIPSS) KW - Femtosecond laser ablation KW - Biofilms KW - Steel PY - 2016 AN - OPUS4-36045 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weltschev, Margit T1 - Comparison of the environmental stress cracking behaviour of polyethylene and polyethylene terephthalate as materials for dangerous goods packagings N2 - The chemical industry has expressed great interest in using polyethylene terephthalate (PET) as material for packagings for the transport of dangerous goods. Due to the high strength and stiffness of PET, the wall thickness and weight of packagings can be reduced. This is a relevant cost factor. PET is a semi-crystalline thermoplast which is produced by polycondensation of terephthalic acid and ethylene glycol. According to the European dangerous goods regulations RID and ADR, samples of PET design types of packagings for dangerous goods must be pre-stored with the original filling good for six months at 23°C, before the design type tests can be carried out. For packagings made of polyethylene (PE) tests to prove the stress cracking resistance by using laboratory methods are possible to reduce time and costs. Therefore, standard liquids, simulating the different types of damaging effects on PE are defined in RID and ADR. However, there is no information and research available about the damaging mechanisms on PET in comparison to PE, especially regarding to stress cracking resistance and test methods. The aim of this work is to compare the stress cracking resistance of PE and PET with the Full Notch Creep Test (FNCT), which was developed by chemical industry and is described in the standards EN ISO 16101 and EN 15507. It was investigated whether testing specimens made of PE and PET with a full coplanar notch around the middle of the specimens show weakening after the impact of a tensile force in a wetting solution (Lutensol® FSA 10) at 50°C in a test device on the basis of the FNCT. The test results confirmed the suitability of the method for eight PE grades. Unfortunately, this method couldn’t be used for PET because the specimens broke during notching. In addition the molding of the sheets and the following temper process for twelve hours are very time-consuming, and the specimens broke during notching due to the high brittleness of PET. Another possibility to provide evidence of stress cracking resistance of PE packagings is laid down in BAM’s Dangerous Goods Rule BAM-GGR 015. This test was carried out with PE and PET bottles to compare both materials. Therefore 1l test bottles were filled with a 5% wetting solution and mounted with a clamping tool for 28 days at 40°C. Tensile test specimens were cut out afterwards from the middle of the bottles in the deformed areas. Tensile strength and breaking elongation of PE specimens were determined in comparison to the PET specimens. The tensile properties of the PET specimens couldn’t be determined due to the strength and the stiffness of the material. In conclusion the only way to provide information about the stress cracking resistance of PET was to perform stacking tests. 1l bottles made of PE and PET were filled with a 5% wetting solution and stored with a stacking load for 28 days at 40°C according to EN ISO 16495. Design types of PE and PET both passed the stacking tests. T2 - EUROCORR 2016 CY - Montpellier, France DA - 11.09.2016 KW - polyethylene terephthalate KW - stress cracking resistance KW - test methods KW - dangerous goods packagings PY - 2016 AN - OPUS4-37448 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erdmann, Maren T1 - Mechanical characterization of high-density polyethylene in contact with diesel and biodiesel fuels N2 - Renewable resources become more and more relevant to maintain energy demands for an increasing global population. Biosynthetic fuels like biodiesel might replace conventional petrochemical fuels, such as diesel. However, more research is needed to characterize the interaction between the different fuels and polymeric materials widely used in the fuel infrastructure as well as for automotive parts. Especially changes in the structural properties and mechanical behavior of the polyethylene (PE-HD) have to be addressed. The presented work comprises the direct interaction of high density polyethylene (PE-HD) with diesel and biodiesel, resulting in swelling and plasticization. Also long-term degradation phenomena will be discussed. The chosen PE-HD types are typical thermoplastic resins for container and storage tank applications. The impact of diesel and biodiesel in PE-HD is investigated by changes in the mechanical properties with emphasis on the Charpy impact strength. Furthermore, structural and dynamic influences on the polymeric material induced by diesel and biodiesel are proven in Dynamic Mechanical Analysis (DMA). Both methods, Charpy impact strength and DMA, reveal softening effects due to the migration of diesel and biodiesel into the amorphous regions of PE-HD. Since biodiesel is more prone to oxidative degradation compared to diesel, the fuel/air/polymer-interaction is studied for partly immersed tensile test specimens. Main focus of the evaluation is the co-oxidation. Here, the accelerated deterioration of PE caused by the sorption of the facile oxidation of biodiesel into the solid polymer might be a major degradation mechanism in this context. T2 - POLYDAYS 2016 CY - Potsdam, Germany DA - 28.09.2016 KW - PE-HD KW - Diesel KW - Biodiesel KW - Oxidation PY - 2016 AN - OPUS4-37677 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scheuerlein, T1 - Mechanical properties of the HL-LHC 11 Tesla Nb3Sn magnet constituent materials N2 - A test campaign was launched to determine the mechanical properties of the HL-LHC 11 T Nb3Sn magnet components in order to accurately model the mechanical properties in Finite Element simulations that predict the stress and strain distribution in These magnets. Static and dynamic test methods have been applied for determining elastic materials behavior, and highly accurate Young’s moduli are obtained with the dynamic methods resonance and impulse excitation. These non-destructive methods also enable temperature dependent modulus measurements during in situ heat cycles. T2 - Applied Superconductivity Conference CY - Denver, Colorado, USA DA - 04.09.2016 KW - Young's modulus KW - Tensile test KW - Resonanz KW - Impact excitation PY - 2016 AN - OPUS4-37414 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scheuerlein, C. T1 - Mechanical properties of the HL-LHC 11 Tesla Nb3Sn magnet constituent materials N2 - A test campaign was launched to determine the mechanical properties of the HL-LHC 11 T Nb₃Sn magnet components in order to accurately model the mechanical properties in Finite Element simulations that predict the stress and strain distribution in these magnets. Static and dynamic test methods have been applied for determining elastic materials behavior, and highly accurate Young’s moduli are obtained with the dynamic methods resonance and impulse excitation. These non-destructive methods also enable temperature dependent modulus measurements during in situ heat cycles. T2 - Applied Superconductivity Conference CY - Denver, USA DA - 04.09.2016 KW - Young´s modulus KW - Tensile KW - Compression KW - Temperature dependence PY - 2016 AN - OPUS4-37922 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mull, Birte T1 - Development of a reproducibly emitting reference material for volatile organic compounds N2 - Volatile organic compounds (VOC) are ubiquitous in the indoor air, since they emit from materials used indoors. Investigations of these materials are mostly carried out in test chambers under controlled climatic conditions. Quality control of these test chamber measurements is important but there is a lack of commercially available homogenous reference materials. The approach of this study is to dope a supporting material with VOCs, which are then reproducibly released in measurable chamber air concentrations between 30 to 300 µg m ³. From several tested supporting materials vacuum grease (APIEZON M) was selected because of its very low own emissions. First tests were conducted with styrene. For the estimation of the initial emission and the emission over time FEM (finite element methods) modelling was used. Based on this, five samples with a surface of 7 cm2 and a thickness of 12 mm with a content of 1 ‰ styrene were investigated at (23 ± 2) °C and (50 ± 5) % relative humidity in the µ-chamber (3 samples) and 24 L test chambers (2 samples) for 28 days. Air samples were taken after 24 hours, 3, 7, 14, 21 and 28 days on Tenax TA® sorption tubes and analyzed by TD-GC-MS. The area specific emission rate (SERa) was calculated to compare the results from both chamber types. After 24 hours SERa was between 0.8 0.9 µg cm 2 h 1 (3800 4000 µg m 3) for the µ-chamber samples and between 0.9 1.1 µg cm 2 h 1 (300-370 µg m 3) for the 24 L test chamber samples. After 28 days the SERa was at 0.2 µg cm 2 h 1 for all samples. The relative standard deviation of the SERa was between 1 26 %. These results show the applicability of vacuum grease as supporting material and the favored starting concentration range could be achieved in the 24 L test chambers. T2 - Indoor Air 2016, the 14th international conference of Indoor Air Quality and Climate CY - Ghent, Belgium DA - 03.07.2016 KW - Emission test chamber KW - Indoor air KW - Quality assurance KW - Quality control PY - 2016 AN - OPUS4-36823 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Becker, Ben T1 - Zustandsüberwachung von Composite-Druckgefäßen mit faseroptischer Sensorik N2 - Einsatz der Faseroptik zur Zustandsüberwachung von Composite-Druckgefäßen. Aufbau, Integration, Messergebnisse. T2 - Follow-up Workshop on Statistical Safety Assessment of Composite Cylinders CY - Berlin, Germany DA - 05.10.2016 KW - Faseroptik KW - Zustandsüberwachung KW - Composite-Druckgefäße PY - 2016 AN - OPUS4-39088 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Marzok, Ulrich T1 - Bestimmung der H2-Permeabilität von Gläsern mit der VHE-Methode N2 - Die Entwicklung von Wasserstoffbarrieren aus Glas erfordert die genaue Messung geringster H2-Permeabililtäten. Bisherige Untersuchungen haben gezeigt, dass die VHE-Pulvermethode diesbezüglich eine besonders hohe Empfindlichkeit bietet. Hierbei wird die isotherme Gasabgabe aus sphärischen Partikeln im Rahmen klassischer Diffusionsmodelle gefittet und daraus der Diffusionskoeffizient bestimmt. Für die Untersuchung von Gläsern mit möglichst geringer H2-Permeabilität ist jedoch eine Validierung der Genauigkeit der Methode notwendig. Vor diesem Hintergrund erfolgte die numerische Modellierung der H2-Abgabe mit Hilfe des Programms COMSOL Multiphysics®. Im Poster wird der Einfluss der Korngrößenverteilung der Glaspulverpartikel, der Partikelform sowie der Effekt einer nichthomogenen H2-Startverteilung auf die mittels Pulvermethode ermittelten Diffusionskoeffizienten diskutiert. T2 - 90. Glastechnische Tagung (Deutsche Glastechnische Gesellschaft e.V.) CY - Goslar, Germany DA - 06.06.2016 KW - Wasserstoffpermeation KW - Glas KW - Vakuumheißextraktion KW - Pulvermethode KW - Simulation PY - 2016 AN - OPUS4-36528 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Welter, T. T1 - Glasstrukturen mit geringer Helium- und Wasserstoffpermeation N2 - Wasserstoffbarrieren aus Glas erfahren zunehmend Bedeutung als Werkstoff in der Energietechnik. Trotz wachsender Anwendungen liegen überwiegend empirisch gewonnene Beziehungen zwischen Glaszusammensetzung und Wasserstoffpermeation vor, die im wesentlichen aus dem Verhalten von Kieselglas abgeleitet werden. In dieser Studie werden daher topologische Parameter der Glasstruktur identifiziert und mit thermodynamischen Parametern korreliert. Auf der Seite der Glastopologie steht das freie Volumen und der Vernetzungsgrad des Netzwerkes während auf der thermodynamischen Seite die Konfigurationsentropie bzw. die Konfigurationswärmekapazität Aufschluss über die Verteilung des freien Volumens geben kann. Dabei wird angenommen, dass für Temperaturen weit unterhalb der Glasübergangstemperatur die chemische Löslichkeit von H2 zu vernachlässigen ist. Um die eingeschränkte Datenlage für die Wasserstoffpermeation kompositionell zu erweitern, wurden zusätzlich Heliumpermeationsmessungen ausgewertet. Die Ergebnisse zeigen, dass für Silicatgläser ein charkteristisches Verhältnis von freiem Volumen zu Netzwerkaufspaltung herrschen muss, um permeationsstabile Gläser zu erhalten. T2 - 90. Glastechnische Tagung CY - Goslar, Germany DA - 06.06.2016 KW - Glasstruktur KW - Helium- und Wasserstoffpermeation KW - Alkalialumosilicatsysteme KW - Thermodynamik KW - Energietechnik PY - 2016 AN - OPUS4-36583 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Marzok, Ulrich T1 - High-temperature laser profilometry N2 - Advanced methods for 3D green density characterization like computed tomography and 3D FE sinter modeling can be utilized for increasing the reliability of sintered components. The experimental in situ observation of sin-tering, however, is currently restricted to silhouette methods, i.e. heating microscopy. For complex shaped sam-ples, in situ shape screening during shrinkage would allow better validation of 3D sinter simulation models. Further, by revealing temporary sinter warpage, 3D high-temperature shape screening would allow to locate potential defects of complex sintered components. Against this background, BAM developed a testing device for in situ 3D high-temperature shape screening for ceramic and glass-ceramic tapes up to 1000°C [1-3]. Current work is focused on dropping this restriction in sample shape and temperature. The poster illustrates the current state of this work and possible applications of the method e.g. in detecting sinter warpage of metallized glass-ceramic LTCC tapes. T2 - 90. Glastechnische Tagung (Deutsche Glastechnische Gesellschaft e.V.) CY - Goslar, Germany DA - 06.06.2016 KW - Laser profilometry KW - 3D High-temperature shape screening KW - Sintering PY - 2016 AN - OPUS4-36510 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Marzok, Ulrich T1 - High-temperature laser profilometry N2 - Advanced methods for 3D green density characterization like computed tomography and 3D FE sinter modeling can be utilized for increasing the reliability of sintered components. The experimental in situ observation of sintering, however, is currently restricted to silhouette methods, i.e. heating microscopy. For complex shaped samples, in situ shape screening during shrinkage would allow much better validation of 3D sinter simulation models. Further, by revealing temporary sinter warpage, 3D high-temperature shape screening would allow to locate potential defects of complex sintered components. Against this background, BAM developed a testing device for in situ 3D high-temperature shape screening for ceramic and glass-ceramic tapes up to 1000°C. Current work is focused on dropping this restriction in sample shape and temperature. The poster illustrates the current state of this work and possible applications of the method e.g. in detecting sinter warpage of metallized glass-ceramic LTCC tapes. T2 - ICC6, 6th International Congress on Ceramics CY - Dresden, Germany DA - 21.08.2016 KW - Laser profilometry KW - 3D High-temperature shape screening KW - Sintering PY - 2016 AN - OPUS4-37708 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Blaeß, Carsten T1 - Sintering and crystallization of new bioactive glasses N2 - Bioglass® 45S5 is mainly used clinically as powders, granules or pastes instead of sintered compacts. This is due to the inherent problem of crystallization during the sintering, which results in poor mechanical properties and reduced bioactivity. Recently, new bioactive glasses with improved crystallization stability have been developed as promising candidates for manufacturing of sintered powder compacts for bone regeneration, which combine improved sintering behavior with bioactivity. Compared with the well-known Bioglass® 45S5 (SiO2-P2O5-CaO-Na2O) the calcium/alkali oxide ratio was increased, sodium oxide was partially replaced by potassium oxide and up to 3 mol% calcium fluoride were added, in order to stabilize the glass against crystallization. The aim of this study was to investigate the sintering and crystallization behavior of these new bioactive glasses. Sintering and crystallization were characterized by heating microscopy, XRD, FTIR, SEM, and DTA. The results show that a sintered density of 88-99 % is achieved in contrast to only 57-67% for Bioglass® 45S5. In addition, FTIR and XRD analyses show that Bioglass® 45S5 crystallized during sintering while for the new glasses no crystalline phases are detected. The thermal properties of all glasses were studied by DTA measurements, and the influence of grain size was characterized. These studies showed that full densification can be attained for particle size < 32 µm, whereas coarser particles progressively increase residual porosity. Observed foaming phenomena, are strongly retarded by crystallization of beta-HAp. T2 - SGT Centenary Conference CY - Sheffield, UK DA - 04.09.2016 KW - Bioactive KW - Glass KW - Crystallization KW - Sintering PY - 2016 AN - OPUS4-38317 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Blaeß, Carsten T1 - Sintering and crystallization of new bioactive glasses N2 - Bioglass® 45S5 is mainly used clinically as powders, granules or pastes instead of sintered compacts. This is due to the inherent problem of crystallization during sintering. Recently, new bioactive glasses with improved crys-tallization stability have been developed as promising candidates for manufacturing of sintered powder compacts for bone regeneration, which combine improved sintering behavior with bioactivity. Compared with the well-known Bioglass® 45S5 (SiO2-P2O5-CaO-Na2O) the calcium/alkali oxide ratio was increased, sodium oxide was partially replaced by potassium oxide and up to 3 mol% calcium fluoride were added, in order to stabilize the glass against crystallization. Sintering and crystallization were characterized by heating microscopy, XRD, FTIR, SEM, and DTA. The results show that a sintered density of 88-99 % is achieved in contrast to only 57-67% for Bioglass® 45S5. Whereas Bioglass® 45S5 powder compacts crystallize during sintering, for the new glasses no crystalline phases were detected. Additionally the influence of grain size was characterized. These studies showed that full densification can be attained for particle size < 32 µm, whereas coarser particles pro-gressively increase residual porosity. Observed foaming phenomena, are strongly retarded by crystallization. T2 - 90. Glastechnische Tagung (Deutsche Glastechnische Gesellschaft e.V.) CY - Goslar, Germany DA - 06.06.2016 KW - Bioactive KW - Glass KW - Crystallization KW - Sintering PY - 2016 AN - OPUS4-38311 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Laquai, René A1 - Müller, Bernd R. A1 - Kupsch, Andreas T1 - Characterizing damage evolution in metal matrix composites with X-ray refraction topography and in situ tensile loading N2 - In this study a metal-matrix-composite with aluminum matrix and Al2O3 particles was investigated with x-ray refraction topography and in-situ tensile loading. It could be observed that after reaching a certain load the specific surface increased steadily. However, the classical radiographs taken for comparison show no damage in the sample. T2 - 8th Joint BER II and BESSY II User Meeting CY - Berlin, Germany DA - 07.12.2016 KW - X-ray refraction KW - Metal matrix composites KW - In-situ loading KW - Synchrotron PY - 2016 AN - OPUS4-39113 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wagner, Sabine T1 - Integration of microspheres coated with fluorescent molecularly imprinted polymers with a fiber optic array for the detection of antibiotics N2 - The widespread use of antibiotics in livestock farming leads to trace residues in food products and wastewater, potentially entailing antimicrobial resistance in food-borne pathogens. The determination of antibiotics in aqueous environments and foodstuff is thus of major concern. Analytical assays based on molecularly imprinted polymers (MIPs) have emerged as a valuable tool in this field due to the low production costs, stability, format adaptability and the possibility to imprint and thus their ability to recognize a wide variety of target analytes. With regard to optical sensing technologies, however, MIPs have only been used in considerably few applications, especially in fluorescence sensors. This limitation is basically due to the fact that the incorporation of a fluorescently responding moiety into a polymer matrix is challenging. One way to overcome this limitation is to use tailor-made fluorescent indicator monomers for direct transfer of the binding event into an optical signal. If such a monomer is integrated into a thin MIP-shell on microspheres such core/shell particles can be readily used in advanced multiplexing sensory fiber-optic microarrays. Here, we propose such a fiber-optic microarray based on fluorescent MIP microspheres for antibiotics. The binding behavior and the selectivity of a microarray using these MIP were examined and compared with a non-imprinted polymer (NIP) control, employing the target molecules and other structurally closely related antibiotics. T2 - Europt(r)ode XIII CY - Graz, Austria DA - 20.03.2016 KW - Molecularly imprinted polymers KW - Fiber-optic microarray KW - Fluorescence PY - 2016 AN - OPUS4-37294 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rizzo, F. T1 - Evaluation of nano-sized internal oxidation in a Fe-13Cr alloy exposed to water vapor atmosphere N2 - The topotactic formation of nano-sized precipitates immediately under the internal oxide layer in a Fe-13Cr alloy exposed to oxidizing water vapor atmosphere was recently reported. The precipitates were identified as lath-shaped Fe-Cr spinel exhibiting a crystallographic orientation relationship with the ferritic matrix. The authors proposed that these precipitates could act as a precursor to the formation of the spinel layer observed in the adjacent part of the oxide scale.The occurrence of internal oxidation in Fe–Cr alloys subjected to similar conditions had been previously identified and directly correlated to the presence of water vapor. In the present work, we attempt to rationalize the processes occurring during the oxidation of this alloy through thermodynamic and kinetic analyses based on the CALPHAD approach, using the geometrical representation of phase equilibria and concepts developed to describe internal oxidation. The influence of water vapor on the mechanism and kinetics of formation of the nano-sized precipitates and its role in the overall oxidation process is also considered. T2 - CALPHAD XLV The forty-fifth International Conference on CALPHAD (Computer Coupling of Phase Diagrams and Thermochemistry) CY - Awaji Island, Hyogo, Japan DA - 29.05.2016 KW - Precipitation KW - Internal oxidation KW - CALPHAD KW - Topotactic transformation KW - Microscopy PY - 2016 AN - OPUS4-42156 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weigert, Florian T1 - Photoluminescence Properties of coreshell CdSe Nanocrystals with Different Shells and Surface Chemistries Derived from Ensemble and Single Particle Measurements N2 - The optical properties of semiconductor nanocrystals (SCNCs) depend on constituent material, particle size, and surface chemistry, with the size of the photoluminescence (PL) quantum yield (QY) and the PL decay kinetics being largely controlled by the number of dangling bonds, which have to be properly passivated for high quality materials. Hence, PL measurements can provide insight not only in SCNC photophysics, yet can be also used for quality control of SCNC synthesis and surface modification. In this respect, steady state and time-resolved fluorometry and confocal microscopy with time correlated single photon counting were used to study the PL properties of core-shell CdSe SCNCs with different shells and surface chemistries on ensemble and single particle level, thereby focusing on a correlation of ensemble PL QY and PL decay kinetics with particle brightness, PL time traces, and the On-time fraction of single SCNCs. Additionally, confocal PL images were correlated with AFM measurements in order to derive the amount of absorbing, yet non-emissive ”dark” SCNCs, the presence of which resulting in an underestimation of ensemble PL quantum yields. The results of this study can help to identify synthetic routes and surface modifications, which minimize the fraction of dark SCNCs. T2 - PicoQuant 22nd International Workshop on Single Molecule and Super-Resolution Microscopy in the Life Sciences CY - Berlin, Germany DA - 14.09.2016 KW - Single molecule KW - SCNC KW - QY KW - AFM KW - Confocal PY - 2016 AN - OPUS4-38121 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Harald Rune T1 - Imaging of local pH in biofilm using polymeric sensors: towards the elucidation of microbial induced corrosion N2 - Microbial induced corrosion (MIC) is a crucial problem in many technical plants as well as fuel tanks, leading to considerable damage and huge financial losses. Successful prevention of MIC requires the localization of first signs of corrosion as well as the identification of factors influencing the corrosion process. In this respect, also the determination of corrosion rates can be of interest for the possible prevention of MIC. Hence, there is a growing need for sensitive and preferably inexpensive tools that enable the early detection of MIC. Of special interest are methods, which provide spatially and time-resolved information and allow the study of changes on metal surfaces as prerequisites for a more detailed analysis of ongoing corrosion processes at a MIC-affected site. Biofilm formation can lead to changes in pH, oxygen and chloride concentration as well as to the release of certain metal ions like Fe(II) and Mn(II) depending on the type of metal surface involved. Hence, optical methods enabling the detection of these analytes at very low concentration and monitoring of their changes can be used for MIC detection. Here, we propose to utilize polymeric nanosensors for MIC detection via the determination of the local pH value changes in different biofilms. Such nanosensors are known to have several advantages in imaging applications such as intracellular pH measurements including the ease of doping or labeling with a multitude of analyte-responsive and inert dye molecules for the realization of a high analyte sensitivity and ratiometric sensing. Moreover, they can be surface functionalized with target-specific ligands e.g., lectins, for the specific binding to the outer surface of certain types of bacteria. In this respect, different polymer architectures will be studied to identify an optimal candidate in terms of imaging performance in conjunction with several classes of pH-responsive fluorescent dyes like cyanines, aza-BODIPYs, and xanthenes, utilizing different mechanism of signal generation such as photo-induced electron transfer or protonation-induced changes in the spectral position of absorption and emission spectra. T2 - Europtrode CY - Graz, Austria DA - 20.03.2016 KW - Nanosensor KW - Microbial induced corrosion KW - Imaging KW - Nanosensor KW - Mikrobiell induzierte Korrosion KW - Bildgebung PY - 2016 AN - OPUS4-35628 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weigert, Florian T1 - Ensemble and single particle studies of the fluorescence properties of core­shell CdSe nanocrystals with different shells and surface chemistries N2 - The optical properties of semiconductor nanocrystals (SCNC) are controlled by constituent material, particle size, and surface chemistry, specifically the number of dangling bonds favoring nonradiative deactivation, and hence also by particle synthesis. In this respect, the fluorescence properties of coreshell CdSe SCNCs with different shells and surface chemistries were studied on ensemble and single particle level, using steady state and timeresolved fluorometry and confocal microscopy with time correlated single photon counting detection. Special emphasis was dedicated to correlate ensemble photoluminescence (PL) quantum yields and decay kinetics with particle brightness, PL time traces, and the Ontime fraction of the single SCNCs. Additionally, the confocal PL images were correlated with AFM measurements in order to derive the amount of absorbing, yet nonemisssive ”dark” SCNCs, the presence of which leading to an underestimation of ensemble PL quantum yields. The results of this study can help to identify synthetic routes and surface modifications minimizing the fraction of dark SCNC, thereby closing the gap to the ultimate goal of colloidally and photochemically stable SCNCs with a PL quantum yield of close to unity. T2 - FQDots16 CY - Berlin, Germany DA - 05.09.2016 KW - Confocal KW - QY KW - QD KW - SCNC KW - Single molecule KW - AFM PY - 2016 AN - OPUS4-38119 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grauel, Bettina T1 - Nd as sensitizer in NaYF4:Yb,Er,Nd tri-doped upconversion nanocrystals N2 - In recent years, upconversion nanocrystals (UCNC) have shown great promise for biological and medical applications, mainly because of their excitation in the NIR region, which provides minimum fluorescence background and a rather deep penetration into biological samples, as opposed to excitation in the visible or UV region. Moreover, they show a multitude of characteristic narrow emission bands as basis for ratiometric measurements. Commonly, Yb is the sensitizer of choice, because of a comparatively high absorption cross section, simple energy scheme, and rather efficient energy transfer to the activator, mostly Er, Tm or Ho. A main disadvantage of the use of Yb as sensitizer for biological and medical applications is its absorption band at 976 nm and hence the use of an excitation wavelength at which water has a non-negligible absorption. This can lead to significant sample heating, especially at long illumination times or high excitation power densities, and thus, tissue damage or even cell death. A possible solution is the tri-doping of UCNC with Nd as sensitizer, which can be excited efficiently at around 800 nm, where water absorption is at minimum. The use of Nd as a sensitizer and Yb as a bridge between Nd and the activator Er in NaYF₄ nanocrystals is a relatively new way to overcome the problems of heating of samples in an aqueous environment. Disadvantages can arise from the tri-doping, which can favor non-radiative relaxation due to the more complicated excitation process compared to e.g., simple Yb,Er-doped UCNC, which might lower the upconversion quantum yields in these tri-doped systems. In order to quantify clear advantages, NaYF₄:Yb,Er,Nd nanoparticles were synthesized and spectroscopically studied using an 8 W 804 nm laser diode and a custom-designed Edinburgh instruments FSP980 spectrometer. Wavelength-dependent studies of the emission intensities and the decay kinetics of these tri-doped UCNC at different excitation power densities and excitation pulse widths revealed the clear advantages of preventing water absorption on measurable luminescence signals. We were able to show the influence of pulse width and excitation power density on the luminescence intensities and decay kinetics lifetimes at different emission wavelengths. Additionally, we can clearly discern power density-dependent and independent peaks in the emission spectra. In summary, we demonstrate that the tri-doping of NaYF₄:Yb,Er,Nd nanoparticles is a very promising approach to render UCNC more efficient and to make them better suitable for biological and medical applications requiring measurements in aqueous environment. T2 - UPCON 2016 Conference CY - Breslau, Poland DA - 23.05.2016 KW - UCNP KW - Nd-sensitizer KW - excitation power density PY - 2016 AN - OPUS4-37224 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Harald T1 - Polymeric sensors as imaging tools for local pH in biofilm for early detection of microbial induced corrosion N2 - Microbial induced corrosion (MIC) is a crucial problem in many technical plants as well as fuel tanks, leading to considerable damage and huge financial losses. Successful prevention of MIC requires the localization of first signs of corrosion as well as the identification of factors influencing the corrosion process.1 Hence, there is a growing need for sensitive and preferably inexpensive tools that enable the early detection of MIC. Of high importance are methods, which provide spatially and time-resolved information and allow the study of changes on metal surfaces as prerequisites for a more detailed analysis of ongoing corrosion processes at a MIC-affected site.2 In this respect, also the determination of corrosion rates can be of interest for the possible prevention of MIC. T2 - 11th International Symposium on Polymer Therapeutics CY - Valencia, Spain DA - 23.05.2016 KW - Bildgebung KW - Mikrobiell induzierte Korrosion KW - Nanosensor KW - Imaging KW - Microbial induced corrosion PY - 2016 AN - OPUS4-37139 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stegemann, Robert T1 - Characterization of residual stress state by neutron diffraction and residual magnetic field mapping N2 - Based on the residual stress characterization of tungsten inert gas welded S235JRC+C plates by means of neutron diffraction, the evaluation of residual stress with high spatial resolution GMR (giant magneto resistance) sensors is discussed. The experiments performed indicate a correlation of residual stress changes and local residual magnetic stray fields. T2 - Eighth Joint BER II and BESSY II User Meeting CY - Berlin, Germany DA - 07.12.2016 KW - Residual stress KW - Magnetic stray fields KW - GMR KW - Neutron diffraction PY - 2016 AN - OPUS4-38676 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mishurova, Tatiana T1 - Surface residual stresses analysis in SLM Ti–6Al–4V bridges N2 - Selective Laser Melting (SLM) technique allows to produce parts with complex geometry. Due to the rapid solidification and heat gradient during production, SLM results in presence of residual stress. The present study shows the influence of manufacturing parameters on surface residual stress of Ti-6Al-4V SLM parts. High tensile stresses in the front surface are found. Heat Treatment conditions relax residual stresses almost to zero. High scanning speed during manufacturing results in higher tensile stresses in the surface. T2 - HZB User Meeting CY - BESSY II, Berlin, Germany DA - 08.12.2016 KW - Additive manufacturing KW - Residual stress KW - Selective laser melting PY - 2016 AN - OPUS4-38657 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cabeza, Sandra T1 - Residual stress characterization of IN718 part obtained by selective laser melting N2 - Additive Manufacturing (AM) by Selective Laser Melting (SLM) offers ample scope for producing geometrically complex parts as compared to the traditional subtractive manufacturing strategies. However, the residual stresses developed during the processing can reduce the load bearing capacity as well as induce unwanted distortion, limiting the application of SLM parts. IN718 manufactured by SLM process can show high tensile residual stresses in the surface as high as the yield strength of the wrought alloy. On the other hand, residual stresses in the bulk Show considerably lower stress values, even in compression, indicating a stress re-distribution during deposition of the SLM layers. T2 - HZB User meeting CY - BESSY II, Berlin, Germany DA - 08.12.2016 KW - Additive manufacturing KW - Residual stress KW - Selective laser melting KW - Neintron diffraction PY - 2016 AN - OPUS4-38660 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Shashev, Yury T1 - Optimizing visibility of phase gratings for Talbot-Lau X-ray imaging N2 - We investigated the efficiency of phase gratings, i.e., the visibility upon variation of different parameters. Rotating around an axis parallel to the grid lines of the phase grating changes the grating’s shape and thereby the initial distribution of phase shifts. This yields high visibilities for shorter propagation distances than derived from box shapes. Tilting the grating in the scattering plane allows continuous tuning of the grating’s height that corresponds to an ideal phase shift for a particular photon energy. This opens the way for tuning the design energy suitable for the material under investigation. Our study included simulations for monochromatic sources with the sampling procedure for rectangular and triangular phase gratings. T2 - HZB - 8th joint BER II and BESSY II User Meeting CY - Berlin, Germany DA - 07.12.16 KW - Phase grating KW - X-ray interferometry KW - X-ray imaging PY - 2016 AN - OPUS4-38823 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Shashev, Yury T1 - Improving visibility of phase gratings for Talbot-Lau X-ray imaging N2 - We investigated the efficiency of phase gratings, i.e., the visibility upon variation of different parameters. Rotating around an axis parallel to the grid lines of the phase grating changes the grating’s shape and thereby the initial distribution of phase shifts. This yields high visibilities for shorter propagation distances than derived from box shapes. Tilting the grating in the scattering plane allows continuous tuning of the grating’s height that corresponds to an ideal phase shift for a particular photon energy. This opens the way for tuning the design energy suitable for the material under investigation T2 - PhD Day 2016 CY - Berlin, Germany DA - 2.09.2016 KW - Phase grating PY - 2016 AN - OPUS4-38323 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hertwig, Andreas T1 - Measurement of porous TiO2 layers with spectroscopic ellipsometry - a multi-method study N2 - By means of an effective medium (EMA) based approach, it is possible to use spectroscopic ellipsometry to determine the mixing ratios between air and material in porous dielectrics and calculate a quantitative value of the porosity for these materials. As this method is model-based, it is very difficult to provide a quantitative measure for the accuracy of porosity values determined by this method. Valuable additional information can often be obtained by combining ellipsometry with other complementary methods. In the present study, the ellipsometry results were validated by Electron Probe Microanalysis (EPMA) with the option of layer analysis (by the socalled “STRATAGem” approach), gravimetry, and electron microscopy. We analysed porous TiO2 thin layers synthesised by means of a template synthesis Approach (evaporation induced self assembly). Ellipsometry measurements on porous samples are difficult to analyse due to the complexity of the models necessary. Often it is difficult to decide if the measured data contains enough information to successfully determine the target quantities (mixing ratio, dielectric function of the matrix material). One method to decrease the complexity of the fit and therefore use the measurement data most efficiently is a multi-sample analysis. In the present case, multi-sample analysis was used for determining the porosity factors of the individual layers while using one common set of dielectric function values for the matrix in all cases. While the results of the fit analysis in this case can be used to show the feasibility and also the limitations of the multi-method approach, the porosity values themselves show a promising agreement between the Independent methods. It can therefore be concluded that determining porosity values with ellipsometry is in accordance to other methods to the level of accuracy provided by the complementary methodologies. T2 - ICSE-7, 7th International Conference on Spectroscopic Ellipsometry CY - Berlin, Germany DA - 5.6.2016 KW - Spectroscopic ellipsometry KW - Electrolysis KW - Catalysis KW - Thin film metrology KW - Porous materials PY - 2016 AN - OPUS4-39940 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rhode, Michael A1 - Mente, Tobias A1 - Böllinghaus, Thomas T1 - Modeling of hydrogen-assisted cracking (HAC) in duplex stainless steels (DSS) N2 - Modeling of Hydrogen-Assisted Cracking (HAC) in Duplex Stainless Steels (DSS): - Hydrogen causes significant degradation in DSS and consequently HAC - Mechanisms of HAC have not been fully understood in two-phase microstructures - Mesoscale numerical modeling for HAC in DSS was created, coupled to the macroscale, enabling simulation of HAC in both phases independent from predefined crack paths T2 - International Hydrogen Conference - Material Performance in Hydrogen Environments CY - Jackson Lake Lodge, Moran, Wyoming, USA DA - 11.09.2016 KW - Hydrogen KW - Numerical modeling KW - Duplex stainless steel KW - Hydrogen assisted cracking PY - 2016 AN - OPUS4-37404 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nützmann, Kathrin T1 - The influence of sulfur on initial high temperature corrosion of Fe-Cr model alloys N2 - Ferritic steels with Cr-contents up to 13 wt. % are used as heat exchanger or boiler tube materials in combustion based power plants. These materials are subject to aggressive corrosion caused by the reaction of the steel with highly corrosive gases under high temperatures up to 650°C. The early stages of corrosion and sulfidation especially and the influence of the Cr-content in the alloy are thereby not understood but of fundamental interest. Our work shows corrosion mechanisms and presents corrosion models for Fe and different Fe-Cr-alloys under pure SO2 und SO2+O2 atmospheres for different time scales. Modell alloys of high purity are used to focus on the reaction of the intended elements: Fe, Cr, S, and O. Long-time experiments (≥12h) took place in tube furnaces and short-time experiments (≥5min) in a special designed light furnace. Heating and cooling took place under inert atmosphere. The reactive gases were added not until the experimental temperature was reached. Samples were analyzed using high resolution synchrotron X-ray diffraction using a micro focus setup and electron microscopy including FIB. Many earlier studies on corrosion and sulfidation on iron based alloys show a higher corrosion rate and material loss when sulfur was present in the atmosphere. In contrast, later studies propose an inhibiting effect of sulfur containing atmospheres. On the one side, most likely due to the formation of a protective layer of Mx(SO4)y -phases at the scale-gas interface. On the other side, a very recent study proposes the theory that MxSy-phases limit the further diffusion of elements. Up to now, no Mx(SO4)y –phases were detected in our samples, but sulfide phases nucleated within the oxide phases. For pure Fe our samples show FeS at the scale-metal interface working as a diffusion barrier for Fe-Cations from the base material in to the oxide scale. The above lying spalled off oxide-sulfide scale shows a wide area of small voids and accumulations of FeS-Crystals at the bottom. Under the main oxide scale a second generation of oxide-sulfide scale starts to form. For the Fe-Cr-alloys the inner oxide scale only shows FeS- and CrS-phases surrounded by hollow space. The here presented study will explain and discuss a new growth model for the shown phenomenon. T2 - 9th High Temperature Corrosion and Protection of Materials CY - Ile des Embiez, France DA - 15.05.2016 KW - Sulfidation KW - Diffusion barrier KW - Fe-Cr alloys PY - 2016 AN - OPUS4-38250 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -