TY - CONF A1 - Fabry, Çağtay T1 - Towards arc welding reference data: Open Science laboratories at BAM N2 - As industries move for ever faster development and adoption cycles of emerging new technologies in the field of welding, the meticulous and longer-winded approach of the scientific research process can feel harder to integrate. To help bridge this gap and increase the speed, quality, and adoption rate of publicly funded research, the Bundesanstalt für Materialforschung und -prüfung (BAM) continues to work towards enabling scientists with direct access to necessary software tools and - in the future – highest quality welding research reference data to further foster collaborations. On the experimental side, the arc welding group at BAM division 9.3 “welding technologies” is continuing to expand and upgrade its capacities of robotic welding systems with integrated state of the art sensor technologies and software solutions. This allows all experiments to be recorded and measured in micro-millimeter accuracy and at sub-millisecond precision, including welding process data, complete spatial geometry and temperature measurements, process video recordings and more. The custom software-based solutions and interfaces allow scaling of the welding systems from large thick plate offshore applications to small additive repair weldments in wind turbine blades to multi-hour continuous weldments in additive manufacturing applications. In addition to the data gathered during the welding process itself, the relevant testing results and materials properties produced at BAM or externally can be integrated seamlessly. This allows detailed traceability of all results back to the actual welding process. Regardless of the scope and application, complete datasets can be made accessible for research or industry partners in the highest resolution based on the open source WelDX (welding data exchange) file format. Figure 1. Welding experiment representation including dynamic process data, cross-section imaging and hardness measurements from a single weldx file. The talk will give an overview of the experimental facilities and workflows as well as current software developments with a focus on research data quality assurance, traceability, and accessibility. Based on the integration into latest research trends and activities of the “welding technologies” division, the path to publishing reference datasets for arc welding process for various applications and materials is outlined and discussed. T2 - 4th Symposium on Materials and Additive Manufacturing - Additive 2024 CY - Berlin, Germany DA - 12.06.2024 KW - Additive Manufacturing KW - Arc welding KW - DED-arc KW - Research data KW - Reference data PY - 2024 AN - OPUS4-60249 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bakir, Nasim A1 - Üstündag, Ömer A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael T1 - Observation of the weld pool shape in partial penetration welding and its influence on solidification crack formation for high-power laser beam welding N2 - In this study, steel-glass experiments were conducted to observe the melt pool geometry using a high-speed camera. The high-speed recordings and optical flow analysis show that two main flows take place in form of vortices. The lower vortex drives the melt backwards from the front keyhole wall and thus causes an extension of the melt pool, which is called bulging. This bulging promotes solidification cracking by forming a closed area filled with melt and the accumulation of impurities in the final solidification phase, resulting in low-melting phases which are under tensile stress at the end of solidification. T2 - Lasers in Manufacturing Conference 2021 CY - Online meeting DA - 21.06.2021 KW - Laser beam welding KW - Weld pool shape KW - Solidification craking KW - Partial penetration PY - 2021 SP - 1 EP - 5 AN - OPUS4-53587 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fabry, Çağtay T1 - WelDX – progress report on the welding data exchange format N2 - The presentation shows the current development status of the Welding Data Exchange (weldx) format based on the Advanced Scientific Data Format (ASDF). The use of a complete single pass arc welding experiment example stored in a single weldx file and validated against a predefined schema definition is presented. The example includes generic experimental metadata, the workpiece geometry and materials definition following associated standards, the weld process spatial movement description, the welding process parameter descriptions and welding process measurements. The inclusion of 3D scan data of the workpiece description is also included. The full code and data is available on GitHub: https://github.com/BAMWelDX/IIW2021_AA_CXII T2 - 2021 IIW Annual Assembly and International Conference on welding and Joining CY - Online meeting DA - 07.07.2021 KW - Arc welding KW - Digitalization KW - Open science KW - Research data management KW - WelDX PY - 2021 AN - OPUS4-53401 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Üstündag, Ömer T1 - Hybrid laser-arc welding of laser and plasma-cut 20 mm thick structural steels N2 - It is already known that the laser beam welding (LBW) or hybrid laser-arc welding (HLAW) processes are sensitive to manufacturing tolerances such as gaps and misalignment of the edges, especially at welding of thick-walled steels due to its narrow beam diameter. Therefore, the joining parts preferably have to be milled. The study deals with the influence of the edge quality, the gap and the misalignment of edges on the weld seam quality of hybrid laser-arc welded 20 mm thick structural steel plates which were prepared by laser and plasma-cutting. Single-pass welds were conducted in butt-joint configuration. An AC magnet was used as a contactless backing. It was positioned under the workpiece during the welding process to prevent sagging. The profile of the edges and the gap between the workpieces were measured before welding by a profile scanner or a digital camera, respectively. With a laser beam power of just 13.7 kW, the single-pass welds could be performed. A gap bridgeability up to 1 mm at laser-cut and 2 mm at plasma-cut samples could be reached respectively. Furthermore, a misalignment of the edges up to 2 mm could be welded in a single-pass. The new findings may eliminate the need for cost and time-consuming preparation of the edges. T2 - 74th IIW Annual Assembly and International Conference 2021 CY - Online meeting DA - 07.07.2021 KW - Hybrid laser-arc welding KW - Thick-walled steel KW - Edge quality KW - Gap bridgeability KW - Misalignment of the edges KW - Plasma-cutting KW - Laser-cutting PY - 2021 AN - OPUS4-53577 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Üstündag, Ömer T1 - Elektromagnetische Schmelzbadbeeinflussung beim Laserhybridschweißen von Dickblechen N2 - -Elektromagnetische Schmelzbadstütze wurde beim Laserhybridschweißen von Dickblechen erfolgreich zur Unterdrückung der Tropfenbildung eingesetzt -Auch bei „schlechteren“ Kantenqualitäten konnten einlagige Schweißnähte mit hoher Qualität erzielt werden -Spaltüberbrückbarkeit bis zu 2 mm (bei plasmageschnittenen Proben) konnte gewährleistet werden -Homogenere Verteilung des Zusatzwerkstoffes wurde erzielt T2 - 42. Assistentenseminar der Wissenschaftlichen Gesellschaft Fügetechnik e.V. CY - Blankenau (Beverungen), Germany DA - 06.10.2021 KW - Laserhybridschweißen KW - Elektromagnetische Schmelzbadbeeinflussung KW - Dickblech PY - 2021 AN - OPUS4-53578 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bakir, Nasim T1 - Observation of the weld pool shape in partial penetration welding and its influence on solidification crack formation for high-power laser beam welding N2 - Solidification cracking is still a particular problem in laser beam welding, especially in the welding of thick-walled plates. In this study, the influence of weld pool geometry on solidification cracking in partial penetration welding of thick plates is a subject of discussion. For this purpose, a special experimental setup of steel and quartz glass in butt configuration and lateral with high speed camera was used to capture the weld pool shape. Additionally, laser beam welding experiments were carried out to compare the crack positions and the cross section with the high-speed camera observations. The results showed a bulge in the weld pool root separated from the upper region by a nick area. This leads to the fact that three different longitudinal lengths with different solidification areas are taking place. This temporal sequence of solidification strongly promotes the solidification cracks in the weld root. T2 - Lasers in Manufacturing Conference 2021 CY - Online meeting DA - 21.06.2021 KW - Solidification cracking KW - Laser beam welding KW - Partial penetration PY - 2021 AN - OPUS4-53586 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strobl, Dominic T1 - Real-time Bead-on-Plate weld Simulation for Wire Arc Additive Manufacturing using Reduced Order modelling coupled with stochastic model Calibration N2 - Numerical simulations are essential in predicting the behavior of systems in many engineering fields and industrial sectors. The development of accurate virtual representations of actual physical products or processes (also known as digital twins) allows huge savings in cost and resources. In fact, digital twins would allow reducing the number of real, physical prototypes, tests, and experiments, thus also increasing the sustainability of production processes and products’ lifetime. Standard numerical methods fail in providing real time simulations, especially for complex processes such as additive manufacturing applications. This work aims to use a reduced order model for efficient wire arc additive manufacturing simulations, calibrations and real-time process control. Model reduction, e.g. the proper generalized decomposition [1,2] method, is a popular concept to decrease the computational effort. A new mapping approach [3] was applied to simulate a moving heat source with the proper generalized decomposition. Using this procedure even complex models can be simulated in real-time. The physical model is later on calibrated with the use of a stochastic model updating process and the reduced order model, leading to an optimized real-time simulation. In this contribution, a proper generalized decomposition model for a bead-on-plate wire arc additive manufacturing is presented. It is also coupled with a stochastic model updating process identifying the heat source characteristics as well as the boundary conditions of the transient thermal problem, whereas the heat source shape is simulated using a Goldak heat source T2 - 15th World Congress on Computational Mechanics (WCCM-XV) CY - Yokohama, Japan DA - 31.07.2022 KW - Wire arc additive manufacturing KW - Reduced order modelling KW - Model calibration PY - 2022 AN - OPUS4-55576 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fabry, Çağtay T1 - WelDX - a file format for processing and archiving welding research data N2 - The talk gives an introduction into gas metal arc welding and its relation to plasma science as well as current challenges in welding research concerning research data management and the application of the FAIR principles. The WelDX project is introduced and the main goals are discussed and contrasted with the current features of the weldx API. Different internal and public facing use cases focusing on research data management and their implementation using weldx are presented. The interactive part of the presentation displays some advanced multi layer use cases and data analysis using the weldx API as well as the integration of materials properties into weldx. T2 - International Workshop on FAIR Data in Plasma Science CY - Online meeting DA - 16.05.2022 KW - WelDX KW - Open science KW - Research data management KW - Arc welding KW - Digital transformation PY - 2022 AN - OPUS4-55153 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Marquardt, R. A1 - Osayi, J. A1 - Kmieciak, S. A1 - Biegler, M. A1 - Rethmeier, Michael T1 - Verschleißschutz einer Schneckengeometrie durch funktional gradierte Materialien N2 - Hochbelastete Stahlbauteile lassen sich durch Auftragen von Kobalt-Chrom Legierungen vor Verschleiß schützen. Die plötzliche Änderung der Materialeigenschaften führt jedoch zu Spannungen und Rissen im Anbindungsbereich. Daraus resultierende Abplatzungen stellen eine Gefahr für die Funktionsfähigkeit der Maschine und damit für Mensch und Umwelt dar. Um die Belastbarkeit der Schutzschicht zu verbessern, kann die Anbindung durch einen gradierten Materialübergang optimiert werden. Diese funktional gradierten Materialien können mittels pulverbasiertem Directed Energy Deposition aufgetragen werden. Die Methodik zum Aufbau und zur Qualitätssicherung solcher Materialien wurde in vorangegangenen Arbeiten für dickwandige Geometrien gezeigt. Für dünnwandige Geometrien ist die Anwendbarkeit bisher unzureichend untersucht worden. Diese Arbeit zeigt am Beispiel einer dünnwandigen gradierten Schneckengeometrie die Einsatzfähigkeit der Methodik. Dafür wird die Gefügestruktur der Gradierung auf Fehler untersucht und der Härteverlauf gemessen. Außerdem wird die relative Dichte anhand eines bereits trainierten neuronalen Netzes vorhergesagt und mit einer Porositätsuntersuchung verglichen. T2 - 14. Tagung Verschleiß- und Korrosionsschutz von Bauteilen durch Auftragschweißen CY - Halle a. d. Saale, Germany DA - 12.06.2024 KW - Directed Enery Deposition KW - Funktionally Graded Material KW - Additive Manufacturing KW - DED KW - FGM KW - AM PY - 2024 SP - 1 EP - 7 PB - SLV Halle AN - OPUS4-60721 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Yang, Fan T1 - Numerical Investigations of Porosity Mitigation in High-Power Laser Beam Welding with an External Magnetic Field N2 - The application of an external magnetic field has been found to significantly mitigate the porosity ratio in laser beam welded joints of AlMg3 aluminum alloy. To investigate the suppression mechanism, a 3D transient multi-physics coupled numerical model of laser beam welding (LBW), including laser propagation, laser-material interaction, and magnetohydrodynamic effects, has been developed to calculate the keyhole dynamics and weld pool behaviors during the welding process. The induced time-averaged Lorenz force is directed downward. Under the effects of the external magnetic field, the fluid flow pattern and the weld pool profile are both affected. The keyhole geometry reconstruction algorithm is proposed to calculate the keyhole diameter and its fluctuation, which is used to evaluate the keyhole stability. The results indicate that the oscillating magnetic field does not affect keyhole stability obviously in the LBW of aluminum alloy. Moreover, an electromagnetic expulsive force is induced on the bubble because of the time-averaged downward Lorentz force. This electromagnetic expulsive force can accelerate the bubble escape speed considerably. An analytical model is developed for investigating the bubble escape window, which shows that the bubble escape window is expanded by 45% under the effect of the external magnetic field. The calculated results based on the developed model agree well with the experimental results. T2 - 77th IIW Annual Assembly and International Conference CY - Rhodes, Greece DA - 07.07.2024 KW - Numerical simulation KW - Deep penetration laser beam welding; Keyhole stability KW - Porosity defects KW - Magnetic field PY - 2024 AN - OPUS4-60667 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bachmann, Marcel T1 - Challenges in Modelling Dynamic Heat Sources in High-Power Laser Beam Welding N2 - The amount of absorbed energy in the keyhole as well as its distribution is essential to model the laser beam welding process. The recoil pressure is a key determining factor for the macroscopic flow of the molten metal in the weld pool during high-power laser beam welding. Consequently, a realistic implementation of the laser radiation on the weld metal is crucial to obtain accurate simulation results. The following developments on the laser-material interaction are discussed for the numerical simulation of the laser beam welding process. The first implemented improvements relate to locating the exact reflection points in the ray tracing method in the determination algorithm for the intersection of the reflected rays and the keyhole surface. A second correction refers to the numerical treatment of the Gaussian distribution of the laser beam, whose beam width is defined by a decay of the laser intensity by a factor of 1/e2 thus ignoring around 14 % of the total laser beam energy. In a third step, the laser radiation distribution in vertical direction was approximated according to the beam caustics. Finally, a virtual mesh refinement was adopted in the ray tracing routine. The obtained numerical results were validated with experimental measurements. T2 - IIW Annual Assembly 2024 CY - Rhodes , Greece DA - 07.07.2024 KW - Laser beam welding KW - Numerical modeling KW - Ray tracing KW - Heat source modeling PY - 2024 AN - OPUS4-60634 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Raute, Julius A1 - Beret, Alexander A1 - Biegler, Max A1 - Rethmeier, Michael T1 - Ökobilanzierung in der additiven Fertigung – Laser- vs. Elektronenstrahl N2 - Die additive Fertigung gewinnt für industrielle Anwendungen zunehmend an Bedeutung. In diesem Zusammenhang sind Verfahren der Directed Energy Deposition (DED) besonders gefragt, um hohe Aufbauraten zu erreichen. Neben den bekannten laserstrahlbasierten Verfahren hat auch der Elektronenstrahl die industrielle Marktreife erreicht. Das Wire Electron Beam Additive Manufacturing bietet zum Beispiel Vorteile bei der Verarbeitung von Kupferwerkstoffen. In der Literatur wird die höhere Energieeffizienz und die daraus resultierende Verbesserung der CO2-Bilanz des Elektronenstrahls hervorgehoben. Es fehlt jedoch an praktischen Studien mit Messdaten, um das Potenzial der Technologie zu quantifizieren. In dieser Arbeit wird eine vergleichende Ökobilanz zwischen der additiven Fertigung mit Draht und Elektronenstrahl (DED-EB) und der additiven Fertigung mit Laserstrahl und Pulver (DED-LB) durchgeführt. Dazu werden die Ressourcen für die Herstellung ermittelt, ein Testbauteil mit beiden Verfahren hergestellt und der gesamte Energieverbrauch gemessen. Die Umweltauswirkungen werden dann mit den Faktoren Treibhauspotenzial (GWP100), Ozonbildungspotenzial (POCP), Versauerungspotenzial (AP), Eutrophierungspotenzial (EP) abgeschätzt. Es zeigt sich, dass das Wire Electron Beam Additive Manufacturing durch einen deutlich geringeren Energiebedarf gekennzeichnet ist. Darüber hinaus gewährleistet die Verwendung von Draht eine größere Ressourceneffizienz, was zu insgesamt besseren Ökobilanzergebnissen führt. KW - Ökobilanzierung (LCA) KW - Additive Fertigung KW - Directed Energy Deposition KW - Kupfer KW - Wire Electron Beam Additive Manufacturing PY - 2024 SP - 26 EP - 32 AN - OPUS4-62234 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rethmeier, Michael T1 - Laser and hybrid welding with ultra high power lasers N2 - Welding with high-power lasers has a history of over 30 years. With the introduction of high-powerCO2 lasers, the subject was investigated as early as the 1990s as part of various research projects. A renewed interest in the subject was awakened with the market launch of high-brilliance, high-power fibre and disc lasers at the beginning of the 2000s. In industrial production, the use of high-power lasers for welding shipbuilding constructions at the same time as for mobile crane construction is mainly associated with low-alloy high-strength steels with a maximum wall thickness of 15 mm. The use of high-power multi 10kW lasers for even greater sheet thicknesses (20mm-100 mm) promises significantly greater advantages [1]. For these wall thicknesses the economic, technological and ecological advantages of the process over conventional welding methods become especially clear and visible [2]. Despite numerous research projects on this topic, laser technology still faces a number of hurdles that need to be overcome. The new lasers with scalable laser powers up to 100 kW and the application of an electromagnetic weld pool support as well as local vacuum environment widen the possible application range tremendously. In this contribution, the authors address the technical solutions for high-power laser beam welding in the field of thick sheet metal applications, highlight the technological and normative challenges in the industrial implementation of the process and present a perspective for the first concrete applications in the field of off-shore wind energy. T2 - Stuttgarter Laser Tage CY - Stuttgart, Germany DA - 04.06.2024 KW - High-power laserbeam welding KW - Thick plates KW - Electromagnetic weld pool support PY - 2024 AN - OPUS4-62412 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gumenyuk, Andrey T1 - Two-colour thermography for measurement of temperature distribution in laser beam welding N2 - Solidification cracking is a frequently observed phenomenon in laser beam welding of austenitic stainless steels and other metallic alloys. Characterisation of cracking susceptibility requires knowledge of the precise and spatially resolved temperature distribution near the solidification front in the welding process. Thermography is a standard tool that provides a qualitative estimate of the 2D temperature field. The general disadvantage of this method is its dependence on the emission characteristics of the measured object. For welding applications, these can vary significantly in the temperature range above and below the melting temperature. For this purpose, we have developed a thermography-based measurement technique using a SWIR camera system in combination with two narrow bandpass filters that use the principle of two-wavelength pyrometry to estimate absolute temperature values. This technique was used to determine the temperature distributions and gradients near the solidification front of laser-welded austenitic steel. The results were validated by other measurements. T2 - 13th CIRP Conference on Photonic Technologies [LANE 2024] CY - Fürth, Germany DA - 16.09.2024 KW - Laser beam welding KW - Solidification cracking KW - FEM simulation PY - 2024 AN - OPUS4-62415 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rethmeier, Michael T1 - Single pass laser vacuum welding of thick steel plates using electromagnetic support N2 - The increasing demand for renewable energy produced by offshore wind turbines goes along with an increased demand in the production of offshore wind turbine foundations, so called “monopiles”, which are made by joining thick metal sheets. The industrial standard of multi-layer submerged arc welding (SAW) for joining of thick metal sheets is the current bottleneck in the production of monopiles. A possible increase in productivity by the implementation of high-power laser welding in a newly developed mobile vacuum chamber (MoVac) and an electromagnetic root support is the subject of this study. Single run butt welds are performed in flat position on S355 mild steel of thicknesses up to 80 mm using a disc laser system with 1030 nm wavelength and a maximum output of 60 kW. The laser optic is fixed on the MoVac-System which is held and manipulated by an articulated robot. T2 - 13th CIRP Conference on Photonic Technologies [LANE 2024] CY - Furth, Germany DA - 15.09.2024 KW - Laser beam welding KW - Laser welding with mobile vacuum PY - 2024 AN - OPUS4-62413 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Meng, Xiangmeng T1 - Prediction of porosity formation in high power laser beam welding using physics informed machine learning framework N2 - The applications of the high-power laser beam welding process are often hindered by the occurrence of the porosity defect. However, an accurate prediction and an insight of the porosity formation are still challenging due to the highly nonlinear physics involved in the dynamic weld pool and keyhole behaviours. In this paper, the effects of relevant physical variables related to the porosity defect are evaluated by utilizing mechanistic modelling and experimental data within a physics-informed machine learning (PIML) framework. With a proper selection of the physical variables (features) in the aspects of keyhole stability, liquid metal flow and weld pool geometry, which correspondingly describes the bubble formation, bubble movement and bubble capture by the solidification front, the PIML shows great superiority in predicting the porosity ratio in the laser welding of aluminium in comparison with conventional ML model using welding parameters. The Shapley Additive Explanations analysis is employed to provide a hierarchical importance of the variables on the defect formation. T2 - 77th IIW Annual Assembly and International Conference CY - Rhodes, Greece DA - 07.07.2024 KW - Laser beam welding KW - Machine learning KW - Porosity KW - Modelling PY - 2024 AN - OPUS4-61610 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Putra, Stephen Nugraha T1 - Numerical study on the temperature characteristic of material absorptivity and its significance in high-power laser beam welding N2 - The absorptivity of metallic materials plays an important role in high-power laser beam welding. It affects the amount of absorbed laser power leading to the heating and melting of the surfaces to be joined and is highly dependent on the temperature. Nonetheless, this key characteristic is often ignored in numerical simulations and an empirical parameter determined by trial-and-error approaches is rather implemented to calibrate the results. In the present work, the temperature dependence of laser absorption is included in a three-dimensional multiphase numerical model considering the coupled fluid flow and heat transfer. The calculated laser absorption is determined by the temperature-dependent material properties, laser characteristics, and incident angle of the laser beam. It is found that the temperature dependence of the laser absorption is crucial for accurately determining the keyhole and weld pool geometries, which is validated by experimental measurements using 304 austenitic steel. T2 - 13th CIRP Conference on Photonic Technologies [LANE 2024] CY - Fürth, Germany DA - 15.09.2024 KW - Laser beam welding KW - Temperature dependent absorption KW - Weld pool KW - Keyhole dynamics KW - Numerical modelling PY - 2024 AN - OPUS4-61612 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Yang, Fan T1 - Assessment of keyhole stability in laser beam welding with external magnetic field using numerical simulation N2 - The challenge of understanding the physical mechanisms behind porosity reduction by a magnetic field during laser beam welding (LBW) is partly due to the difficulty in quantitatively evaluating keyhole stability. The commonly used index, such as keyhole depth, is typically one-dimensional, which is insufficient to capture the dynamic and three-dimensional fluctuations of the keyhole. In this paper, by utilizing a 3D multiphysical model of LBW with magnetic field, a novel keyhole geometry reconstruction algorithm has been developed to describe the keyhole profile and its fluctuation in a statistical manner to evaluate keyhole stability quantitatively. An equivalent diameter is proposed in this algorithm to reduce the irregularity of the keyhole geometry. The calculation results indicate that the time-averaged keyhole shape over 300 ms in the LBW of steel is conical, regardless of the application of an external magnetic field, which provides a more representative shape. Meanwhile, it is observed from the statistical aspect that the keyhole diameter becomes smaller, except the top part, under the influence of the magnetic field. The standard deviation of the equivalent diameter can be used as a physical variable to assess the keyhole stability quantitatively. The application of an external magnetic field can produce a noticeable reduction of the standard deviation of the equivalent diameter, namely, stabilizing the keyhole during LBW of steel. However, the different contribution from the keyhole stability affected by a magnetic field in suppressing porosity is different with materials. T2 - International Congress of Applications of Lasers & Electro-Optics 2024 CY - Los Angeles, CA, USA DA - 04.11.2024 KW - Deep penetration laser beam welding KW - Numerical simulation KW - Keyhole shape KW - Keyhole stability KW - Magnetic field PY - 2024 AN - OPUS4-61600 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Yang, Fan A1 - Meng, Xiangmeng A1 - Putra, Stephen Nugraha A1 - Bachmann, Marcel A1 - Rethmeier, Michael T1 - Numerical studies of magnetohydrodynamic technology in suppressing process porosity during laser beam welding N2 - The magnetohydrodynamic (MHD) technology is employed to mitigate the porosity problem during partial penetration laser beam welding (LBW) of 10 mm thick aluminum alloy. The effectiveness and universal applicability of the MHD technology in reducing porosity during the LBW process are confirmed by a reduction in the porosity ratio of more than 89%. A transient 3D multi-physical model coupled with the MHD effect has been developed to investigate the suppression mechanism of process porosity. Due to the influence of Lorentz force, there is an obvious change in the weld pool length. This change widens the escaping channel of bubbles escaping from the weld pool. The application of an oscillating magnetic field changes the fluid flow pattern noticeably, whose influence on the formation of porosity defects is highly complicated and nonlinear. T2 - 13th CIRP Conference on Photonic Technologies CY - Nuremberg, Germany DA - 15.09.2024 KW - Laser beam welding KW - Aluminum alloy KW - Process Porosity KW - Porosity suppression KW - Magnetohydrodynamic technology PY - 2024 AN - OPUS4-61604 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Meng, Xiangmeng A1 - Putra, Stephen Nugraha A1 - Bachmann, Marcel A1 - Rethmeier, Michael T1 - Parametric study of the laser energy absorption in high-power laser beam welding N2 - Laser energy absorption on the keyhole wall is decisive for the thermodynamic behavior and the resultant weld properties in the high-power laser beam welding process. However, its highly transient nature on a microsecond scale makes the quantitative analysis challenging. In this paper, the influence of the relevant welding parameters on laser energy absorption is studied statistically by utilizing multiphysical modeling, in which the three-dimensional transient keyhole dynamics and thermo-fluid flow are calculated. A dynamic mesh adaption technique and a localized level-set-based ray-tracing method are employed to improve the model accuracy further. The results show that the focus position has a remarkable effect on the time-averaged laser absorption, and in contrast, the laser energy distribution regime is only slightly influenced by the welding speed in the studied parameter range (1.5–3.0 m/min). The absorption ratio of the laser energy on the keyhole front wall decreases with increasing welding speed and increases with upward-moving focus positions. The comparison between the calculated results and the experimental measurements ensures the validity of the proposed model. T2 - International Congress of Applications of Lasers & Electro-Optics 2024 CY - Los Angeles, CA, USA DA - 03.11.2024 KW - Laser beam welding KW - Laser energy absorption KW - Multiphysics modeling KW - Parametric study KW - Weld pool PY - 2024 SP - 1 EP - 8 AN - OPUS4-61629 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -