TY - CONF A1 - Üstündag, Ömer T1 - Analysis of microstructure and mechanical properties of single-pass laser hybrid welded thick-walled steels up to 30 mm with contactless electromagnetic backing N2 - The study deals with the influence of the heat input on the thermal cycles, the microstructure and the mechanical properties for laser-hybrid welded steels of S355J2 with thicknesses up to 30 mm using a 20-kW high-power laser with contactless electromagnetic backing. The focus is on the change of the mechanical properties over the seam thickness. Therefore, the impact toughness and tensile strength were tested in different depths. Based on the experiments, a heat input of 1.3 kJ/mm - 1.6 kJ/mm, 2 kJ/mm - 2.4 kJ/mm and 3.7 kJ/mm were recommended when single-pass welding of 20 mm, 25 mm and 30 mm with a 20-kW laser in regard to the minimum requirements of the mechanical properties, respectively. Lower heat inputs led to undesired microstructure consisting of martensite, hardening and deteriorated impact toughness, where higher heat inputs led to grain-coarsening and even loss of impact strength due to the formation of retained-austenite on the grain boundaries. T2 - EMPOrIA 2023 - International Joint Conference CY - Aachen, Germany DA - 16.05.2023 KW - Laser hybrid welding KW - Electromagnetic backing KW - Thermal cycles KW - Charpy impact toughness KW - Thick-plate welding PY - 2023 AN - OPUS4-58614 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Putra, Stephen Nugraha A1 - Meng, Xiangmeng A1 - Bachmann, Marcel A1 - Rethmeier, Michael T1 - Der Einfluss verschiedener räumlicher Diskretisierungsansätze des Ray-Tracing-Verfahrens bei der Simulation des Laserstrahltiefschweißen N2 - Die Wärmeverteilung des Lasers beim Laserstrahltiefschweißen ist für die Formgebung der Dampfkapillare und für die Schweißbaddynamik entscheidend. In dieser Arbeit werden die Laserwärmeverteilung und deren Einflüsse auf die Schweißbadtiefe sowie -breite numerisch anhand des Ray-Tracing-Verfahrens analysiert. Hierbei wird der La-serstrahl in mehreren Strahlenbündeln bzw. Subrays unterteilt. Diesbezüglich soll der Pfad der Subrays präzis be-rechnet werden, um die Dynamik der Dampfkapillare und des Schweißbades eines realen Schweißprozesses rich-tig abzubilden. Zu diesem Zweck beschäftigt sich die vorliegende Arbeit mit der Genauigkeitsverbesserung der Kontaktposition und der Reflexionsrichtung der Subrays auf der freien Oberfläche anhand der Level-Set-Methode. Um die Güte dieses Simulationsansatzes zu gewährleisten, wurde eine Gegenüberstellung mit den zwei klassischen Ray-Tracing-Verfahren mittels drei verschiedenen Benchmark-Testreihen durchgeführt. Anschließend wurden die Versuchsergebnisse zur Validierung der implementierten numerischen Ansätze verwendet. Im Rahmen dieser Arbeit kann es gezeigt werden, dass unterschiedliche Wärmeverteilung aufgrund der verschiedenen Ray-Tracing-Verfahren deutlich zu erkennen ist, welche wiederum die Schweißbaddynamik sowie die lokalisierte Dampfkapil-lardynamik stark beeinflussen. Ferner wurde es bestätigt, dass die implementierte Level-Set-Methode zu einer ge-naueren Ermittlung der Kontaktposition und der Reflexionsrichtung der Subrays und somit zu einer Verbesserung der simulierten Schmelzkontur führt. T2 - 43. Assistentenseminar Füge- und Schweißtechnik CY - Schwarzenberg/Erzgebirge, Germany DA - 27.09.2022 KW - Laser beam welding KW - Ray tracing method KW - Weld pool dynamics KW - Numerical modeling PY - 2023 UR - https://www.dvs-media.eu/de/neuerscheinungen/4584/43.-assistentenseminar-fuegetechnik SN - 978-3-96144-212-6 VL - 386 SP - 91 EP - 102 PB - DVS Media GmbH CY - Düsseldorf AN - OPUS4-59119 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gook, Sergej A1 - El-sari, Bassel A1 - Biegler, Max A1 - Rethmeier, Michael T1 - Application of AI-based welding process monitoring for quality control in pipe production N2 - The paper presents the experimental results into the development of a multi-channel system for monitoring and quality assurance of the multi-wire submerged arc welding (SAW) process for the manufacture of large diameter pipes. Process signals such as welding current, arc voltage and the acoustic signal emitted from the weld zone are recorded and processed to provide information on the stability of the welding process. It was shown by the experiments that the acoustic pattern of the SAW process in a frequency range between 30 Hz and 2.5 kHz contains the most diagnostic information. The on-line quality assessment of the weld seam produced is carried out in combination with methods of artificial intelligence (AI). From the results obtained, it can be concluded that the use of the latest concepts in welding and automation technology, combined with the high potential of AI, can achieve a new level of quality assurance in pipe manufacturing. KW - Submerged arc welding KW - Artificial intelligence KW - High-strength fine-grain steels KW - Quality control PY - 2024 DO - https://doi.org/10.37434/tpwj2024.06.01 SN - 0957-798X IS - 6 SP - 3 EP - 8 PB - The Paton Publishing House AN - OPUS4-61000 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Neumann, Benedikt A1 - Biegler, Max A1 - Goecke, Sven-Frithjof A1 - Rethmeier, Michael T1 - Detektion von Bindefehlern beim DED-Arc T1 - Detection of Lack of Fusion during DED-Arc N2 - Based on artificial intelligence (AI) developed for monitoring arc welding, this article presents a deep neural network for monitoring lack of fusion defects in wire arc additive manufacturing of aluminium. The aim is to detect defects in built-up volumes on the basis of weld source data. These can be successfully processed by the algorithm presented and a trained AI. The achieved accuracy of the network is 90 percent. N2 - In dem Beitrag wird aufbauend auf Machine-Learning-Modellen, welche bereits zum Überwachen des Schutzgasschweißen erforscht wurden, ein tiefes neuronales Netz (DNN) zum Monitoring beim DED-Arc von Aluminium vorgestellt. Ziel ist die Detektion von Bindefehlern in den aufgebauten Volumina auf Grundlage von in Echtzeit gemessenen Schweißstromquellensignalen. Es werden Merkmalsvariablen durch Vorverarbeitung extrahiert sowie die Korrelation zwischen den Merkmalsvariablen und den Defekten analysiert. Durch den vorgestellten Algorithmus werden diese automatisiert als Input an ein DNN übergeben. Das entwickelte und trainierte neuronale Netz erkennt anhand signifikanter Merkmale aus den Strom- und Spannungsdaten Bindefehler mit einer Genauigkeit von ca. 90 Prozent. KW - DED-Arc KW - Aluminiumschweißen KW - Bindefehler KW - Prozessüberwachung KW - Maschinelles Lernen KW - Deep Neural Network PY - 2024 DO - https://doi.org/10.1515/zwf-2024-1107 VL - 8 SP - 577 EP - 583 PB - Walter de Gruyter GmbH AN - OPUS4-61630 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gumenyuk, Andrey T1 - Determination of critical local straining conditions for solidification cracking at laser beam welding by experimental and numerical methods N2 - The phenomenon of solidification cracking has been the subject of numerous research projects over the years. Great efforts have been made to understand the fundamentals of hot cracking. It is generally agreed that solidification cracks form in the solidification range between the liquidus and solidus temperatures under the combination of thermal, metallurgical and mechanical factors. There is still a need to determine the time-resolved strain distribution in the cracksensitive region in order to analyse the local critical conditions for solidification cracking phenomena. This was a strong motivation for the development of a measurement system used in this study to estimate the local strains and strain rates in the zone where the solidification crack is expected to occur. The laser beam welding experiments were conducted using the Controlled-Tensile-Weldability test (CTW test) to apply an external strain condition during welding to generate solidification cracks. The CTW test is a test method for investigating the suscep�tibility of laser-welded joints to solidification cracking, in which the sample can be subjected to a defined strain at a defined strain rate during welding. In combination with experimental investigations, numerical simulations provide spatially detailed and time-dependent information about the strain development during the welding process, especially regarding the critical conditions for solidification cracking. Therefore, this tool was also used in the present study to evaluate the accuracy of measurement methods and to estimate experimentally derived values and their concrete influence on the formation of solidification cracks. By integrating experimental methods and numerical simulations, this study investigates the spatially resolved and temporally changing development of strain during welding, with a particular focus on the critical conditions that lead to the formation of solidification cracks. T2 - GAMM 94th Annual Meeting CY - Magdeburg, Germany DA - 18.03.2024 KW - Laser beam welding KW - Solidification cracking KW - FEM simulation PY - 2024 AN - OPUS4-62417 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Marquardt, R. A1 - Gook, S. A1 - Biegler, M. A1 - Rethmeier, Michael T1 - Handgeführtes Laserstrahlschweißen am T-Stoß eines niedrig legierten Stahls N2 - Das handgeführte Laserstrahlschweißen gewinnt in der Industrie zunehmend an Bedeutung, da die hohe Produktivität und die einfache Handhabung Unternehmen wirtschaftliche Vorteile bieten. Derzeit ist der Einsatz in der Industrie jedoch auf Teile mit ästhetischen Anforderungen beschränkt, die häufig aus hochlegiertem Stahl bestehen. Um das Handschweißen mit Laserstrahl auch für Bauteile aus kostengünstigen Stähle mit guten mechanischen Eigenschaften einsetzen zu können, untersucht diese Studie den Einfluss des Schutzgases auf die Porosität am mikrolegierten Stahl HX340LAD mit einer Dicke von 1,5 mm. Getestet wurden die Gase Argon, Stickstoff, CO2 sowie Mischungen aus Argon und CO2 an T-Stöße mit Zusatzdraht. Die Qualifizierung der Porosität erfolgte gemäß DIN EN ISO 13919-1 an Querschliffen als auch mittels Röntgenuntersuchung. Die Ergebnisse zeigen, dass für diesen Stahl die Bewertungsgruppe B mittels CO2 als Schutzgas erreicht werden kann. Stickstoff führt zu Gruppe C, Argon zu D. KW - Handgeführtes Laserstrahlschweißen KW - HHLW KW - Stahl KW - Laser PY - 2025 VL - 2025 IS - 06 SP - 44 EP - 47 PB - DVS Media AN - OPUS4-63345 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Marquardt, R. A1 - Osayi, J. A1 - Kmieciak, S. A1 - Biegler, M. A1 - Rethmeier, Michael T1 - Verschleißschutz einer Schneckengeometrie durch funktional gradierte Materialien N2 - Hochbelastete Stahlbauteile lassen sich durch Auftragen von Kobalt-Chrom Legierungen vor Verschleiß schüt-zen. Die plötzliche Änderung der Materialeigenschaften führt jedoch zu Spannungen und Rissen im Anbindungs-bereich. Daraus resultierende Abplatzungen stellen eine Gefahr für die Funktionsfähigkeit der Maschine und damit für Mensch und Umwelt dar. Um die Belastbarkeit der Schutzschicht zu verbessern, kann die Anbindung durch einen gradierten Materialübergang optimiert werden. Diese funktional gradierten Materialien können mit-tels pulverbasiertem Directed Energy Deposition aufgetragen werden. Die Methodik zum Aufbau und zur Quali-tätssicherung solcher Materialien wurde in vorangegangenen Arbeiten für dickwandige Geometrien gezeigt. Für dünnwandige Geometrien ist die Anwendbarkeit bisher unzureichend untersucht worden. Diese Arbeit zeigt am Beispiel einer dünnwandigen gradierten Schneckengeometrie die Einsatzfähigkeit der Methodik. Dafür wird die Gefügestruktur der Gradierung auf Fehler untersucht und der Härteverlauf gemessen. Außerdem wird die relative Dichte anhand eines bereits trainierten neuronalen Netzes vorhergesagt und mit einer Porositätsuntersuchung verglichen. T2 - 14. Tagung Verschleiß- und Korrosionsschutz von Bauteilen durch Auftragschweißen CY - Halle (Saale), Germany DA - 12.06.2024 KW - Directed Enery Deposition KW - Funktionally Graded Material KW - Additive Manufacturing KW - DED KW - FGM KW - AM PY - 2024 AN - OPUS4-62688 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rethmeier, Michael A1 - Gook, Sergej A1 - Biegler, Max A1 - Gumenyuk, Andrey T1 - Anwendung einer Kombination aus Laserhybrid- und Unterpulverschweißen zum Fügen dicker Bleche aus Schiffbaustahl EH36 N2 - In diesem Beitrag wird ein Schweißverfahren vorgestellt, mit dem 30 mm dicke Bleche aus Schiffbaustahl EH36 effizient und werkstoffgerecht gefügt werden können. Die wirtschaftlichen Vorteile des Verfahrens ergeben sich aus dem Wegfall der aufwendigen Kantenvorbereitung und der Reduzierung des Schweißzusatzbedarfs. Die Stumpfschweißnähte werden in einer Lagen-/Gegenlage-Technik durch Laserhybridschweißen und Unterpulverschweißen ausgeführt. Dabei erfolgt die Laserhybridschweißung als Einschweißung mit einer Tiefe von etwa 25 mm, während die Unterpulvernaht als zweiter Durchgang auf der gegenüberliegenden Seite des Bauteils mit einer Einschweißtiefe von 8 mm aufgebracht wird. Die Überlappung der beiden Lagen gewährleistet einen geschlossenen Nahtquerschnitt. Dank der partiellen Durchschweißung der Laserhybridnaht entfällt die Notwendigkeit zur Wurzelformierung. Darüber hinaus bietet die Prozesskombination eine höhere Toleranz gegenüber Ungenauigkeiten in der Kantenvorbereitung, was die Prozesskomplexität reduziert. Der Einsatz dieses robusteren Verfahrens, das weniger von einer präzisen Kantenvorbereitung abhängig ist, erleichtert die Produktionsvorbereitung, minimiert die Fehleranfälligkeit und senkt die Nachbearbeitungskosten. Dies macht das Laserhybridschweißen besonders attraktiv für Anwendungen im Schiffbau. T2 - 22. Tagung Schweißen in der maritimen Technik und im Ingenieurbau CY - Hamburg, Germany DA - 13.05.2025 KW - Laserhybridschweißen KW - Unterpulverschweißen KW - Kerbschlagbiegeversuch PY - 2025 SP - 87 EP - 98 PB - DVS – Deutsche Verband für Schweißen und verwandte Verfahren e. V AN - OPUS4-63342 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Winkler, Michael T1 - Automated Repair of Gas Turbine Blades Using DED-Arc N2 - Gas turbine blades are critical components in aerospace and power generation, often subject to wear, erosion, and fatigue-induced damage. Traditional repair methods are labor-intensive, costly, prone to inconsistencies, and not rapidly adaptable. This work presents an automated approach for repairing gas turbine blade tips using Wire and Arc Directed Energy Deposition (DED-Arc) in combination with a high-precision point to point registration technique of laser line triangulation (LLT) 3D scans. The proposed workflow begins with affixation of the milled down turbine blade to a work piece manipulator using a 3D printed clamping mechanism and a rough alignment of the turbine tip. Subsequently, the turbine blade’s geometry is acquired using a fully integrated 3D laser triangulation sensor, transforming, and aggregating the captured 2D line data into a 3D scan in the working user coordinate system using live feedback data from a finely calibrated industry robot. This point cloud representation of the real-world turbine blade is then used as the target during an advanced point-to-point shape registration technique transforming the digital representation of the repair process containing all relevant tool path and geometry data into the coordinate system of the real-world turbine blade. Afterwards, the turbine tip is then iteratively repaired whereby the turbine tip geometry is divided into differentiated sections, each with its own optimized process parameter set. A key innovation in this approach is the adaptability of the repair process through a closed-loop monitoring system. After each DED-Arc deposition, a 3D scan is performed to document the deposited geometry, to detect the interaction of the different process parameter sets, to activate an intervention if necessary, and calculate subsequent tool paths based on current geometry data. The results indicate that the combination of precise 3D scan registration with DED-Arc is a viable solution for the industrial-scale repair of gas turbine blades leading to significant reduction in labor, tooling, process, and time related cost. T2 - IIW Assembly CY - Genoa, Italy DA - 22.06.2025 KW - DED-Arc KW - Additive Manufacturing KW - Repair KW - Turbine Blade KW - Automation PY - 2025 AN - OPUS4-63624 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bachmann, Marcel A1 - Putra, Stephen Nugraha A1 - Yang, Fan A1 - Meng, Xiangmeng A1 - Pusbatzkies, Pablo A1 - Rethmeier, Michael T1 - Elucidation of the Laser Beam Energy Attenuation by the Vapor Plume Formation during High Power Laser Beam Welding N2 - In high-power laser beam welding, a common phenomenon is the formation of a keyhole caused by the rapid evaporation of the material. Under atmospheric pressure, this evaporation generates a vapor plume that interacts with the laser beam, leading to energy attenuation and scattering of the laser radiation along its path. These interactions affect the stability of the process and the overall weld quality. This study investigates the influence of the vapor plume on the weld pool and keyhole dynamics during high-power laser beam welding of AlMg3 aluminum alloy through experimental and numerical approaches. The primary goal is to identify key vapor plume characteristics, particularly its length fluctuations, and to improve the accuracy of the numerical models. To achieve this, an algorithm was developed for the automated measurement of the vapor plume length using high-speed imaging and advanced data processing techniques. The measured plume length is then used to estimate the additional vapor heating and laser energy attenuation using the Beer–Lambert law. A refined numerical CFD model, incorporating 3D transient heat transfer, fluid flow, and ray tracing, was developed to evaluate the vapor plume’s impact. Results show that already the time-averaged plume length effectively captures its transient influence and aligns well with experimental weld seam geometries. Additionally, energy scattering and absorption caused by the vapor plume led to a wider weld pool at the top surface. The study also shows an increased percentage of keyhole collapses due to the reduced laser power absorption at the keyhole bottom, further highlighting the importance of accurately modeling vapor plume effects. T2 - International Congress of Applications of Lasers & Electro-Optics 2025 CY - Orlando, USA DA - 12.10.2025 KW - Laser beam welding KW - Vapor plume formation KW - Weld pool KW - Keyhole dynamics KW - Numerical modeling PY - 2025 SP - 1 EP - 10 AN - OPUS4-64817 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Meng, Xiangmeng T1 - A statistical investigation of the laser energy absorption and keyhole stability in high-power laser beam welding N2 - The behaviour of the weld pool in high-power laser beam welding is significantly influenced by laser absorption and keyhole stability, which determines the final weld qualities. However, their dynamic features and multi-coupled interactions make in-depth analyses difficult. This study addresses the challenges by conducting a thorough statistical evaluation of the effects of welding parameters on laser absorption and keyhole fluctuations, using experimental investigations and a well-validated numerical model. From a statistical aspect, the laser energy distribution and the keyhole collapse, commonly considered highly time-varying, show clear regularities. Three distinct regions of the time-averaged energy distribution are identified. The possibility of the keyhole collapse positions obeys a universal normal distribution. The statistical data show greater potential in revealing some well-known, industry-related but unclearly explained findings, such as the saturation of the weld penetration with increasing heat input and the physical basis of the contributions of different welding parameters in the porosity reduction. T2 - The 14th International Seminar Numerical Analysis of Weldability CY - Graz, Austria DA - 21.09.2025 KW - Laser beam welding KW - Energy absorption KW - Keyhole stability KW - Multi-physics modelling PY - 2025 AN - OPUS4-64811 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Meng, Xiangmeng T1 - A statistical assessment of the laser energy absorption and keyhole stability in high-power laser welding N2 - The behavior of the weld pool in high-power laser beam welding is significantly influenced by laser absorption and keyhole stability, which determines the final weld qualities. However, their dynamic features and multi-coupled interactions make in-depth analyses difficult. This study addresses the challenges by conducting a thorough statistical evaluation of the effects of welding parameters on laser absorption and keyhole fluctuations, using experimental investigations and a well-validated numerical model. From a statistical aspect, the laser energy distribution and the keyhole collapse, commonly considered to be highly time-varying, show clear regularities. Three distinct regions of the time-averaged energy distribution are identified. The possibility of the keyhole collapse positions obeys a universal normal distribution. The statistical data show greater potential in revealing some well-known, industry-related but unclearly explained findings, such as the saturation of the weld penetration with increasing heat input and the physical basis of the contributions of different welding parameters in the porosity reduction. T2 - 78th IIW Annual Assembly CY - Genoa, Italy DA - 22.06.2025 KW - Laser beam welding KW - Energy absorption KW - Keyhole stability PY - 2025 AN - OPUS4-64810 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Chaurasia, Prashant Kumar T1 - Automated In-situ Monitoring and Analysis of Process Signatures and Build Profile During Arc-based Directed Energy Deposition N2 - Automated in-situ synchronous monitoring and analysis of key process signatures during arc-based directed energy deposition (DED) process are the key challenges for layer-by-layer printing of large-scale parts. An attempt is presented here for real-time monitoring of process transients, deposit profile, and quantitative assessment of arc power, energy input and its influence on deposit dimensions. The workflow including setup, job generation and data analysis is fully automated in Python to allow large scale experiments with fast analysis results. T2 - 2nd Online Young Welding Professional International Conference CY - Online meeting DA - 06.02.2025 KW - Additive Manufacturing KW - Arc welding KW - DED-arc KW - Monitoring KW - Deposition profile PY - 2025 AN - OPUS4-62663 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hälsig, André A1 - Eßbach, Tim-Bernd A1 - Scharf-Wildenhain, Ronny A1 - Altobelli, Martin Gabriel A1 - Phadnis, Prathamesh Jayant A1 - Hensel, Jonas A1 - Fabry, Çağtay A1 - Pittner, Andreas A1 - Armansyah, T1 - Qualitätssicherung beim Lichtbogenschweißen N2 - Der fortschreitende Trend der Automatisierung und Dokumentation sowie die wirtschaftliche und technische Optimierung von Fügeaufgaben machen es notwendig, Sensoren zielführend in bestehende und vorhandene Anlagentechnik zu integrieren. Jedoch bietet die reine Datenerfassung alleine nur einen geringen Mehrwert. Erst durch eine optimierte Datenspeicherung, eine intelligente sowie automatische Datenauswertung und -bewertung entsteht ein echter Nutzen für den industriellen Anwender. Zur Qualifizierung einer standardisierbaren Herangehensweise der Qualitätssicherung beim Lichtbogenschweißen wurden mit einer nationalen Arbeitsgruppe bestehende Unstetigkeiten der Qualitätsbeeinflussung geschweißter Bauteile aufgeschlüsselt und definiert. Parallel dazu wurde ein automatisiertes Schweißsystem mit hochgenauer Messtechnik (u. a. Stromstärke, Spannung, Drahtvorschub, Thermokamera, Geometriescanner usw.) ausgerüstet und validiert. Hierfür wurde die Open-Source-Technologie WelDX der BAM genutzt. Anschließend wurden bewusst fehlerhaft geschweißte Nähte im Vergleich zu fehlerfreien Referenzschweißungen hergestellt, Messdaten erfasst und analysiert. Im Rahmen dieses Beitrags werden erste Ergebnisse und Erkenntnisse in Bezug auf die Detektion und Bewertung von Unstetigkeiten beim Lichtbogenschweißen dargestellt. Dabei wurde deutlich, dass alternative Darstellungs- und Analysemethoden wie die Anwendung der Mahalanobis-Distanz im Stromstärke-Spannungs-Diagramm eine eindeutigere Korrelation zwischen Unstetigkeiten und Prozesssignalen ermöglichen. T2 - DVS CONGRESS 2025 CY - Essen, Germany DA - 16.09.2025 KW - Lichtbogenschweißen KW - Qualitätssicherung KW - Forschungsdatenmanagement KW - WelDX PY - 2025 SN - 978-3-96144-298-0 VL - 401 SP - 76 EP - 85 PB - DVS Media GmbH CY - Düsseldorf AN - OPUS4-64565 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fabry, Çağtay T1 - WelDX Projektvorstellung N2 - Der Vortrag gibt eine Übersicht über die fortlaufende Entwicklung des WelDX Projektes an der BAM. Die Notwendigkeit des Datenaustausches für die deutsche Forschungslandschaft im Bereich des Lichtbogenschweißens wird motiviert und die wesentlichen Funktionen der weldx Python-Bibliothek anhand von Forschungsbeispielen dargestellt. T2 - Sitzung des DVS Fachausschuss FA03 - Lichtbogenschweißen CY - Ilmenau, Germany DA - 13.05.2025 KW - Forschungsdatenmanagement KW - Lichtbogenschweißen KW - Digitalisierung KW - Weldx PY - 2025 AN - OPUS4-63278 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fabry, Çağtay T1 - Welding Process Data Management - openBIS workflows and lab integration N2 - Arc welding processes are an important manufacturing technology applied to a wide range of critical materials and components such as offshore constructions, pressure vessels and additive manufacturing. Data management for experimental arc welding research faces the challenge of constantly changing experimental setups, incorporating a wide range of custom sensor integrations. Measurements include timeseries process and temperature recordings, 3D-geometry data and video recordings of the process from a sub-millisecond scale to multiple hour-long experiments. In addition, various manual pre-processing steps of the workpieces need to be considered to track the complete manufacturing process and its analysis – from raw materials to final dataset and publication. As a unified RDM system, the BAM Data Store offers the capability to incorporate all steps – albeit not without its own challenges. The talk gives an overview of the different workflows and processing steps along the welding experiments together with their integration into the BAM Data Store. Current solutions and ongoing integration work is explained and discussed. This includes the direct integration and upload of automated processing steps into the Data Store from different machines and sensors using custom Python APIs. Ultimately the complete processing chain across multiple internal steps should be represented in the Data Store. T2 - openBIS user group meeting 2025 CY - Berlin, Germany DA - 22.09.2025 KW - Data Store KW - Openbis KW - Research Data Management KW - Research data KW - Digitalisation PY - 2025 AN - OPUS4-64203 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pittner, Andreas A1 - Winterkorn, René T1 - Life cycle assessment of fusion welding processes considering upstream and downstream process steps N2 - In manufacturing, fusion welding processes consume significant resources, presenting a significant opportunity for reducing environmental impact. Although there is a qualitative understanding of the environmental implications of these processes, a quantitative assessment of key parameters remains complex. This study introduces a welding-specific methodology that employs life cycle assessment (LCA) to quantitatively evaluate the environmental footprint of fusion welding technologies. Our approach identifies and analyses the principal parameters affecting the environmental performance of various welding techniques, including traditional joint welding and additive manufacturing via the Direct Energy Deposition-Arc (DED-Arc) process. Real-time resource usage data is integrated to offer an innovative framework for directly deriving environmental impacts. This research contributes to optimising welding processes by providing a precise and quantifiable measure of their ecological impact. This facilitates the advancement of sustainable manufacturing practices. T2 - Joining Smart Technologies - International Automotive Conference CY - Wels, Austria DA - 10.05.2023 KW - Life Cycle Assessment KW - Arc welding KW - Additive manufacturing KW - DED-Arc PY - 2023 AN - OPUS4-59494 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Artinov, Antoni T1 - A General Analytical Solution for Two-Dimensional Columnar Crystal Growth during Laser Beam Welding of Thin Steel Sheets N2 - The main solidification parameters, namely the crystal axis, the growth rate, and the cross-sectional area of the columnar crystal control the primary microstructure and thus the final weld seam properties. Limited understanding of solidification parameters due to complexities in experimental and theoretical weld pool boundary determination and its mathematical description. Application of local Lamé curves for efficient weld pool boundary reconstruction Derivation of general analytical solutions for the main solidification parameters of a two-dimensional columnar crystal growth during laser beam welding of thin steel sheets. The Lamé curves approximation technique was successfully applied for the reconstruction of the rear part of the two-dimensional steady-state weld pool boundary. General analytical expressions for the main solidification parameters, namely the crystal axis, the growth rate and the cross-sectional area of the crystal were derived. The derived expressions and herewith obtained results were verified and validated by comparing them to known theoretical solutions and experimental measurements. Dimensionless analysis of the influence of the size and shape of the rear weld pool boundary on the solidification parameters was provided. The derived general solutions and the analysis provided allow for critical welding parameters to be estimated and adapted accordingly to improve the welding process. T2 - 3rd International Conference on Advanced Joining Processes CY - Braga, Portugal DA - 19.10.2023 KW - Laser beam welding KW - Analytical solution KW - Columnar crystal growth PY - 2023 AN - OPUS4-59174 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - El-Sari, B. A1 - Biegler, M. A1 - Gook, S. A1 - Rethmeier, Michael T1 - KI zur Prozessüberwachung im Unterpulverschweißen N2 - Beim Unterpulverschweißen sind die Prozessgeräusche ein Indikator für eine gute Fügequalität. Diese Beurteilung kann i.d.R. nur von einer erfahrenen Fachkraft durchgeführt werden. Eine kürzlich entwickelte künstliche Intelligenz kann automatisch das akustische Prozesssignal anhand vortrainierter Merkmale klassifizieren und die Fügequalität anhand des Geräuschs beurteilen. Der Algorithmus, einmal richtig trainiert, kann den Prüfaufwand beim Unterpulverschweißen deutlich reduzieren. KW - Unterpulverschweißen KW - Künstliche Intelligenz KW - Prozessüberwachung KW - Körperschall PY - 2024 SP - 1 EP - 2 AN - OPUS4-59483 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pittner, Andreas A1 - Winterkorn, René T1 - Life cycle assessment of fusion welding processes strategies and implementation N2 - In manufacturing, fusion welding processes use a lot of resources, which presents an opportunity to reduce environmental impact. While there is a general understanding of the environmental impact of these processes, it is difficult to quantitatively assess key parameters. This study introduces a welding-specific methodology that uses life cycle assessment (LCA) to evaluate the environmental impact of fusion welding technologies. Our approach analyses the main parameters that affect the environmental performance of different welding techniques, including traditional methods and additive manufacturing through the Direct Energy Deposition-Arc (DED-Arc) process. We integrate real-time resource usage data to offer an innovative framework for directly deriving environmental impacts. This research contributes to optimising welding processes by providing a precise and quantifiable measure of their ecological impact, facilitating the advancement of sustainable manufacturing practices. T2 - CEMIVET - Circular Economy in Metal Industries CY - Berlin, Germany DA - 06.06.2023 KW - Life Cycle Assessment KW - Fusion welding KW - Additive manufacturing KW - DED-Arc PY - 2023 AN - OPUS4-59499 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -