TY - THES A1 - Bertovic, Marija T1 - Human Factors in Non-Destructive Testing (NDT): Risks and Challenges of Mechanised NDT T1 - Human Factors bei der zerstörungsfreien Prüfung (ZfP): Risiken und Herausforderungen mechanisierter ZfP N2 - Non-destructive testing (NDT) is regarded as one of the key elements in ensuring quality of engineering systems and their safe use. A failure of NDT to detect critical defects in safetyrelevant components, such as those in the nuclear industry, may lead to catastrophic consequences for the environment and the people. Therefore, ensuring that NDT methods are capable of detecting all critical defects, i.e. that they are reliable, is of utmost importance. Reliability of NDT is affected by human factors, which have thus far received the least amount of attention in the reliability assessments. With increased use of automation, in terms of mechanised testing (automation-assisted inspection and the corresponding evaluation of data), higher reliability standards are believed to have been achieved. However, human inspectors, and thus human factors, still play an important role throughout this process, and the risks involved in this application are unknown. The overall aim of the work presented in this dissertation was to explore for the first time the risks associated with mechanised NDT and find ways of mitigating their effects on the inspection performance. Hence, the objectives were to (1) identify and analyse potential risks in mechanised NDT, (2) devise measures against them, (3) critically address the preventive measures with respect to new potential risks, and (4) suggest ways for the implementation of the preventive measures. To address the first two objectives a risk assessment in form of a Failure Modes and Effects Analysis (FMEA) was conducted (Study 1). This analysis revealed potential for failure during both the acquisition and evaluation of NDT data that could be assigned to human, technology, and organisation. Since the existing preventive measures are insufficient to defend the system from identified failures, new preventive measures were suggested. The conclusion of the study was that those preventive measures need to be carefully considered with respect to new potential risks, before they can be implemented, thus serving as a starting point for further empirical studies. To address the final two objectives, two preventive measures, i.e. human redundancy and the use of automated aids in the evaluation of NDT data, were critically assessed with regard to potential downfalls arising from the social interaction between redundant individuals and the belief in the high reliability of automated aids. The second study was concerned with the potential withdrawal of effort in sequential redundant teams when working collectively as opposed to working alone, when independence between the two redundant individuals is not present. The results revealed that the first redundant inspector, led to believe someone else will conduct the same task afterwards, invested the same amount of effort as when working alone. The redundant checker was not affected by the information about the superior experience of his predecessor and—instead of expected withdrawal of effort—exhibited better performance in the task. Both results were in contradiction to the hypotheses, the explanations for which can be found in the social loafing and social compensation effects and in the methodological limitations. The third study examined inappropriate use of the aid measured in terms of (a) agreement with the errors of the aid in connection to the frequency of verifying its results and in terms of (b) the overall performance in the task. The results showed that the information about the high reliability of the aid did not affect the perception of that aid’s performance and, hence, no differences in the actual use of the aid were to be expected. However, the participants did not use the aid appropriately: They misused it, i.e. agreed with the errors committed by the aid and disused it, i.e. disagreed with the correct information provided by the aid, thereby reducing the overall reliability of the aid in terms of sizing ability. Whereas aid’s misuse could be assigned to low propensity to take risks and reduced verification behaviour because of a bias towards automation, the disuse was assigned to the possible misunderstanding of the task. The results of these studies raised the awareness that methods used to increase reliability and safety, such as automation and human redundancy, can backfire if their implementation is not carefully considered with respect to new potential risks arising from the interaction between individuals and complex systems. In an attempt to minimise this risk, suggestions for their implementation in the NDT practice were provided. N2 - Die zerstörungsfreie Prüfung (ZfP) wird als eines der wichtigsten Qualitätssicherungsmaßnahmen für technische Systeme und deren sichere Anwendung betrachtet. Wenn die ZfP kritische Defekte in sicherheitsrelevanten Anlagen, wie z.B. in der Kerntechnik, nicht entdeckt, kann dies zu katastrophalen Folgen für die Umwelt und den Menschen führen. Deshalb muss gewährleistet sein, dass die Verfahren der ZfP zuverlässig sind, d.h. dass sie alle kritischen Defekte entdecken können. Die Zuverlässigkeit der ZfP wird von menschlichen Faktoren beeinflusst, die jedoch bisher in diesem Feld selten betrachtet wurden. Durch den verstärkten Einsatz von Automatisierung beispielsweise bei der mechanisierten Prüfung (automatisierungsunterstütze Prüfung und die zugehörige Datenbewertung) wurde die Erreichung eines höheren Zuverlässigkeitsniveaus erwartet. Menschliche Faktoren sind trotz der Automatisierung immer noch bedeutsam für den gesamten Prüfprozess. Die Risiken der stärkeren Automatisierung der Prüfungen sind nicht vollständig bekannt. Das generelle Anliegen dieser Arbeit ist die erstmalige Feststellung der Risiken der mechanisierten ZfP und das Aufzeigen von Möglichkeiten, diese zu verringern. Die konkreten Ziele dieser Arbeit sind dementsprechend (1) die potenziellen Risiken bei der mechanisierten Prüfung aufzuzeigen und zu analysieren, (2) präventive Maßnahmen für diese Risiken abzuleiten, (3) diese präventiven Maßnahmen kritisch hinsichtlich neuer Risiken zu beleuchten sowie (4) Umsetzungsvorschläge aufzuzeigen. Für die ersten zwei Ziele wurde eine Risikoabschätzung mit der Fehlzustandsart- und auswirkungsanalyse (FMEA) durchgeführt (Studie 1). Diese Analyse ergab Fehlermöglichkeiten während der Datenaufnahme und –bewertung bei der mechanisierten ZfP, die dem Menschen, der Technik und der Organisation zugeordnet werden können. Weil die vorhandenen präventiven Maßnahmen unzureichend für die Vermeidung der identifizierten Fehler waren, wurden neue präventive Maßnahmen vorgeschlagen. Die Schlussfolgerung der Studie zeigt, dass vor der Umsetzung präventiver Maßnahmen eine sorgfältige Betrachtung hinsichtlich neuer potenzieller Risiken erfolgen muss. Dies war der Ausgangspunkt für die weiteren empirischen Untersuchungen. Für die letzten beiden Ziele wurden zwei präventive Maßnahmen untersucht: die menschliche Redundanz und die Anwendung automatisierter Assistenzsysteme bei der ZfP-Datenbewertung. Im Fokus lagen potenzielle Schwachstellen, die aus sozialer Interaktion der redundanten Individuen und aus dem Vertrauen in die hohe Zuverlässigkeit der automatisierten Assistenzsysteme entstehen können. In der zweiten Studie wurde die potenzielle Reduzierung der Anstrengung in sequentiellen redundanten Teams untersucht, indem die gemeinsame Aufgabenbearbeitung in Teams der individuellen Aufgabenbearbeitung gegenüber gestellt wurde. Die Ergebnisse zeigten, dass der erste redundante Prüfer, dem mitgeteilt wurde, dass ein anderer Prüfer die Prüfaufgabe nach ihm durchführen wird, die gleiche Anstrengung investierte wie der individuelle Bearbeiter. Der zweite redundante Prüfer (redundant checker) wurde durch die Information, dass sein Vorprüfer die höherwertige Erfahrung besitzt, nicht hypothesenkonform beeinflusst - anstelle der erwarteten Rücknahme der Anstrengung - zeigte er eine bessere Leistung bei der Durchführung der Aufgabe. Beide Ergebnisse stehen in Widerspruch zu den Hypothesen und können durch social loafing und social compensation Effekte sowie durch methodische Aspekte erklärt werden. In der dritten Studie wurde die unangemessene Nutzung eines automatisierten Assistenzsystems untersucht operationalisiert als (a) die Übereinstimmung mit Fehlern des Systems verbunden mit der Überprüfungshäufigkeit seiner Ergebnisse und (b) die Leistung bei der Aufgabe. Die Ergebnisse zeigten, dass die Information über die hohe Zuverlässigkeit des Systems die Wahrnehmung der Systemleistung nicht beeinflusste und folglich keine Unterschiede in der tatsächlichen Nutzung des Systems zu finden waren. Die Probanden nutzten jedoch das System nicht angemessen: sie stimmten den Fehlern des Systems zu (automation misuse) und sie lehnten korrekte Informationen des Systems ab (automation disuse). So reduzierten sie die Gesamtzuverlässigkeit des Systems, zumeist bei der Fehlergrößenbestimmung. Während misuse mit einer niedrigen Risikobereitschaft und eingeschränkten Überprüfungsverhalten auf Grund des automation bias erklärt werden kann, wird disuse dem möglichen Missverstehen der Aufgabe zugeordnet. Die Ergebnisse dieser Studien haben das Bewusstsein dafür erhöht, dass Methoden zur Erhöhung der Zuverlässigkeit und Sicherheit sowie Automatisierung und menschliche Redundanz versagen können, wenn die potenziellen Risiken ihrer Umsetzung aufgrund der Interaktion zwischen Mensch und Technik nicht bedacht werden. Um diese Risiken bei der Anwendung präventiver Maßnahmen zu minimieren, wurden Vorschläge für die ZfP-Praxis erarbeitet. T3 - BAM Dissertationsreihe - 145 KW - Failure modes and effects analysis KW - Zuverlässigkeit KW - Menschliche Faktoren KW - Zerstörungsfreie Prüfung KW - Fehlzustandsart- und auswirkungsanalyse KW - Personelle Redundanz KW - Human factors KW - Non-destructive testing KW - Human redundancy KW - Automation bias KW - Reliability PY - 2016 UR - https://nbn-resolving.org/urn:nbn:de:kobv:83-opus4-71292 SN - 978-3-9817502-7-0 DO - https://doi.org/10.14279/depositonce-4685 SN - 1613-4249 VL - 145 SP - 1 EP - 161 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-36090 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Basan, Ricardo T1 - Untersuchung der intralaminaren Schubeigenschaften von Faserverbundwerkstoffen mit Epoxidharzmatrix unter Berücksichtigung nichtlinearer Effekte N2 - Faserverbundwerkstoffe besitzen anisotrope Materialeigenschaften. Die Anzahl der elastischen Größen und Festigkeiten zur Beschreibung des mechanischen Verhaltens ist dadurch größer als zum Beispiel bei isotropen Werkstoffen. Die Festigkeiten und die Steifigkeiten in den verschiedenen Laminatrichtungen unterscheiden sich darüber hinaus um bis zu zwei Größenordnungen. Abhängig von der Belastungsart versagen Faserverbundwerkstoffe spröde oder duktil. Der Entwicklung geeigneter Untersuchungsmethoden zur Bestimmung der Werkstoffeigenschaften in den verschiedenen Richtungen kommt daher eine grundlegende Rolle zu. Insbesondere die Bestimmung der intralaminaren Schubeigenschaften von Faserverbundwerkstoffen ist aufgrund des ausgeprägten nichtlinearen Last-Verformungs-Verhaltens schwierig und mit den bestehenden Auswerteroutinen genormter Prüfverfahren teilweise fehlerbehaftet. Im Rahmen dieser Arbeit erfolgt die Analyse der Schubeigenschaften in der Laminatebene durch eine neu entwickelte Schubvorrichtung, die eine qualitativ hochwertige Bestimmung der Werkstoffeigenschaften ermöglicht. Für die Probekörper dieser Schubvorrichtung wird auf der Grundlage von Messergebnissen ein lastabhängiges Modell der Schubspannungsverteilung entwickelt, das die Materialnichtlinearität berücksichtigt und bei der Analyse der Versuchsergebnisse zur Anwendung kommt. In vergleichenden Untersuchungen der Interaktion benachbarter Schichten an glas- und kohlenstofffaserverstärkten Laminaten mit ein- und zweiachsiger Orientierung kann gezeigt werden, dass bei identischem Schubspannungszustand in den Einzelschichten bis zu 60% größere Schubfestigkeiten der zweiachsig verstärkten Verbunde vorliegen. Die orthogonal verstärkten Laminate sind schadenstoleranter, da sich Zwischenfaserbruche nicht ungehindert ausbreiten können, sondern an den um 90° gedrehten Fasern gestoppt werden. In Laminaten mit unidirektionaler Faserausrichtung führt dagegen der erste Riss unmittelbar zum Trennbruch. Die Verifizierung dieser Beobachtung erfolgt mittels des Verfahrens der Röntgenrefraktions- topographie. In Schubzugversuchen erfolgt die Korrelation der mechanischen Belastungssituation mit der mikrostrukturellen Analyse der inneren Schädigungsentwicklung des Werkstoffs. An zweiachsig verstärkten Kohlenstofffaserlaminaten unter Zwischenfaserbruchbeanspruchung kann gezeigt werden, dass die Degradation der intralaminaren Schubsteifigkeit mit der Zunahme an inneren Oberflachen als Maß für die Zwischenfaserbruchdichte einhergeht. Einachsig verstärkte Verbunde versagen dagegen relativ spröde bereits durch den ersten Zwischenfaserbruch und damit ohne Zunahme der Mikrorissdichte. Die Zusammenfassung der Erkenntnisse spiegelt sich in der Verbesserung des Auswerteverfahrens des in DIN EN ISO 14129 genormten Schubzugversuchs wider. Unter Berücksichtigung der Nichtlinearitat des Schubmoduls und der Faserrotation infolge der großen Verformungen während des Schubzugversuchs erfolgt in einem Iterationsprozess die stuckweise Anwendung der Klassischen Laminattheorie zur Bestimmung der Einzelschichtspannungen. Die Bewertung der Ergebnisse des Schubzugversuchs mit diesem Analyseverfahren hinsichtlich der Belastungsgrenzen resultiert in einer guten Übereinstimmung mit dem Festigkeitsmodell nach Puck. Die Berücksichtigung nichtlinearer Effekte führt zu einer höheren Genauigkeit bei der Bestimmung der intralaminaren Schubfestigkeit mittels des in der industriellen Anwendung weit verbreiteten Normversuchs. T3 - BAM Dissertationsreihe - 74 KW - Zwischenfaserbruch KW - interfibre failure KW - nonlinearity KW - test methods KW - in-plane shear KW - composite materials KW - Faserverbundwerkstoffe KW - intrlaminare Schubeigenschaften KW - Prüfverfahren KW - Nichtlinearität PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-848 SN - 978-3-9814281-3-1 SN - 1613-4249 VL - 74 SP - 1 EP - 170 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-84 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Bartholmai, Matthias T1 - Flammschutz von polymeren Baustoffen: Bewertung von Konzepten auf der Basis von Small-scale Cone Calorimeter Untersuchungen N2 - Flammschutz von polymeren Baustoffen: Bewertung von Konzepten auf der Basis von small- scale Cone Calorimeter Untersuchungen. In der Arbeit wurden zwei unterschiedliche Flammschutzkonzepte polymerer Baustoffe mit Hilfe des Cone Calorimeter untersucht und bewertet. Polymer-Schicht-Nanocomposites sind ein neues Konzept für flammgeschützte Werkstoffe, die aus einer Polymermatrix und der Zugabe eines nanoskaligen Schichtsilikat- Additivs von ca. 5 Gew.-% bestehen. Im Brandfall bilden die Schichtsilikate eine Barriere, die den Wärmetransport in das Material bzw. den Stofftransport der Pyrolysegase aus dem Material hemmt. Mit einem Modellsystem wurde gezeigt, dass dieser Barriereeffekt das Brandverhalten hinsichtlich der Flammenausbreitung verbessert, in anderen Brandszenarien aber wirkungslos bleibt. Die Ergebnisse der Cone Calorimeter Untersuchungen wurden mit denen der Entflammbarkeitstests UL 94 und LOI verglichen. Eine Korrelation in Richtung kleiner Probendimensionen (downscale) und in Richtung Phase der Brandentstehung wurde aufgezeigt. Die Anwendung intumeszierender Beschichtungen auf Bauteile verschiedener Art, wie z. B. tragende Stahlkonstruktionen, ist ein etabliertes Brandschutzkonzept. Das intumeszierende Polymermaterial schäumt unter Wärmeeinwirkung auf und bildet eine wärmeisolierende Schicht. Zur Bewertung der Wirkungsweise dieses Polymermaterials wurde ein auf Temperaturmessungen basierendes Verfahren mit dem Cone Calorimeter und für Simulationsrechnung entwickelt. Die Ergebnisse wurden mit denen aus Kleinprüfstanduntersuchungen verglichen. Eine Korrelation in Richtung großer Probendimensionen (upscale) und in Richtung der Phase des voll entwickelten Brandes konnte bis zu einer Temperaturgrenze gezeigt werden. N2 - Objective of this thesis was the investigation and evaluation of two different concepts of flame-retarding polymeric building materials. In the centre of this concern is the cone calorimeter as a versatile device in the field of flame retardancy and burning behaviour of materials and constructions. The cone calorimeter is characterized by a medium sample dimension (100 x 100 mm2). It simulates the phase of flame spread of a real burning process. The capabilities of the sample materials were of interest as well as the potentials and limitations of the investigation method. The scientific significance of cone calorimeter results was analysed in terms of different fire Scenarios and sample dimensions. Polymer Layered Silicate Nanocomposites are a new concept of flame retarding materials consisting of a polymer matrix and the addition of about 5 wt.-% nanoscale clay. In the case of a fire the clay layers built up a barrier, which hinders the heat transport into the sample and the mass transport of pyrolysis gases out of the material. Using a model system it was shown, that this barrier effect results in an essential improvement in burning behaviour in terms of flame spread but was ineffective for different fire scenarios and phases of burning, respectively. The results of cone calorimeter measurements were compared to results of the flammability tests UL 94 and LOI. A correlation towards smaller sample dimensions (downscale) and towards the phase of flammability was shown. The application of intumescent coatings on different structural members like supporting steel constructions is an established concept of fire retardancy. The intumescent polymeric material swells under thermal impact and forms a heat insulating layer. A method combining temperature measurement using the cone calorimeter and Computer simulation was developed, by which the fire protective effect could be evaluated. Investigation results were compared to results of small scale test furnace measurements. A correlation towards larger sample dimensions (upscale) and towards the phase of a fully developed fire could be shown up to a limitation by temperature. T3 - BAM Dissertationsreihe - 22 KW - Flammschutz KW - Small-scale Cone Calorimeter Untersuchungen KW - polymeren Baustoffen PY - 2007 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1366 SN - 978-3-86509-652-4 SN - 1613-4249 VL - 22 SP - 1 EP - 181 PB - Wirtschaftsverlag NW CY - Bremerhaven AN - OPUS4-136 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Babutzka, Martin T1 - Neue Erkenntnisse zur Deckschichtbildung von Zink an der Atmosphäre T2 - Berichte aus der Werkstofftechnik N2 - Die Korrosionsbeständigkeit und die Dauerhaftigkeit von Zink und Zinküberzügen an der Atmosphäre sind direkt mit der Bildungs- und Auflösungskinetik von schützenden Deckschichten aus festhaftenden Korrosionsprodukten verknüpft. Bei einem optimalen Zusammenwirken und einer günstigen Abfolge von atmosphärischen Einflussfaktoren bilden sich gut schützende, bei Feuchtigkeitszutritt nahezu unlösliche Deckschichten aus. Art und Eigenschaften der gebildeten Deckschichten hängen dabei insbesondere von den Luftinhaltsstoffen der Einsatzumgebung sowie von spezifischen Temperatur-Feuchte-Zyklen ab. Dabei besteht das Problem, dass sich die klimatischen Bedingungen und infolge auch die Deckschichtbildungsreaktionen bei Zink an der Atmosphäre im Laufe der letzten Jahrzehnte stark geändert haben. Das Ziel der vorliegenden Arbeit ist die systematische Untersuchung und Beschreibung von Korrosions- und Deckschichtbildungsvorgängen bei Reinzink unter den aktuell in der Bundesrepublik Deutschland vorherrschenden klimatischen Bedingungen. Die Untersuchungen zielen in ihrer Gesamtheit auf das Hinterfragen aktueller und die Etablierung neuer Betrachtungsweisen zur Deckschichtbildung bei Reinzink unter atmosphärischen Korrosionsbedingungen ab und sollen damit einen wesentlichen Beitrag für das Verständnis des Korrosionsschutzes durch Zink und Zinküberzüge liefern. Dabei wurde der Fokus insbesondere auf das Anfangsstadium der Deckschichtbildung gelegt. Eine systematische Untersuchung dieses Zeitraums, der von sehr reaktiven Deckschichten geprägt ist, wurde erst durch den gezielten Einsatz gelartiger Elektrolyte ermöglicht. KW - Zink KW - Korrosion KW - Deckschichtbildung KW - Atmosphäre KW - gelartige Elektrolyte PY - 2020 SN - 978-3-8440-7626-4 DO - https://doi.org/10.2370/9783844076264 SN - 0945-1056 SP - 1 EP - 181 PB - Shaker Verlag CY - Düren AN - OPUS4-51458 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Artinov, Antoni T1 - On the mathematical analysis of the relationship between the bulging region and the centerline solidification cracking in laser beam welding N2 - The present Ph.D. thesis provides a comprehensive experimental and theoretical study of the bulging-cracking relationship in laser beam welding of thick unalloyed steel sheets. It focuses on experimentally proving the existence of the bulging region and on developing a coupled multiphysics mathematical framework to analyze its influence on the three critical factors controlling the susceptibility to solidification cracking, namely the thermal, metallurgical, and mechanical factors. The research employs a novel experimental setup, utilizing a combination of transparent quartz glass and thick unalloyed steel sheet, enabling real-time visualization of the weld pool geometry and confirming the existence of a distinctive bulging region. To deepen the understanding of these experimental insights, an extensive multiphysics mathematical framework was developed and rigorously verified and validated. This framework introduces an innovative approach using Lamé curves for accurately describing complex three-dimensional weld pool geometries, including the bulging region's characteristics. Through analytical solutions and numerical procedures, it facilitates the computation of solidification parameters, which are crucial for understanding the metallurgical aspects of crack formation. The framework also incorporates a mechanical model to assess and evaluate the local stress distribution within the bulging region. The findings indicate that an elongated, sharply shaped bulging region significantly increases the susceptibility to solidification cracking. This is attributed to its adverse impact on the distribution and local dwell time of liquid metal residing at grain boundaries during solidification, combined with the localized tensile stresses identified in the bulging region. In essence, this research contributes to the broader understanding of solidification cracking in laser beam welding of thick unalloyed steel sheets, with a particular focus on the bulging region. The insights and methodologies developed in this thesis are valuable for future research and advancements in the application of the laser beam welding technology for joining high-thickness unalloyed steel components. KW - Bulging effect KW - Centerline solidification cracking KW - Mathematical modeling KW - Structural steel KW - High power laser beam welding PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-599010 DO - https://doi.org/10.14279/depositonce-20090 SP - 1 EP - 152 CY - Berlin AN - OPUS4-59901 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Aristia, Gabriela T1 - Polyaniline/Silicon Dioxide Composite-Based Coating for Corrosion Protection in Geothermal Systems N2 - Geothermal energy is one of the cleanest renewable alternatives to reduce the dependency on fossil fuel [1, 2]. Despite its promising future, its implementation faces various challenges, one of them being corrosion processes. To implement this energy, hot fluids are pumped from a geothermal well. These hot fluids originate from deep within the earth, so consist of different ionic species and gases in a wide range of temperatures, which lead to their corrosive nature. In terms of geothermal energy resources, Indonesia is at the forefront, with the highest preserved geothermal energy in the world of about 29 GWe and 312 potential geothermal locations [3]. Geothermal wells in Sibayak (North Sumatera), Indonesia, belong to young stratovolcanoes and have operating temperatures varying from 36 °C at the near ground surface to 310 °C at the bottom of the well, which is liquid-dominated with acidic and saline properties [4, 5]. Therefore, this geothermal fluid creates an aggressive environment that is conducive to corrosion of the powerplant infrastructure. Parts of the geothermal powerplant infrastructure, such as pipelines and heat exchangers, are commonly made of metals, e.g. carbon steel and stainless steel. Consequently, they may undergo corrosion and scaling when exposed to the geothermal fluid, especially for carbon steel. To ensure the safety and longevity of a geothermal powerplant, the infrastructure is constructed of expensive corrosion resistant alloys [6–10], e.g., titanium and Ni-Cr based alloys, or carbon steel which needs to be protected by coatings or inhibitors. To address the corrosion of carbon steel in the geothermal environment, artificial geothermal water was used to simulate a geothermal well in Sibayak, Indonesia, with pH 4 and a saline composition of 1,500 mg/l Cl-, 20 mg/l SO42-, 15 mg/l HCO3-, 200 mg/l Ca2+, 250 mg/l K+, and 600 mg/l Na+. Carbon steel underwent the most severe corrosion at 150°C in an oxygen-containing solution with a corrosion rate of 0.34 mm/year, which is approximately ten times higher than that in the absence of dissolved oxygen. In all conditions, pitting corrosion was observed, which necessitate a protection strategy on carbon steel. In order to promote a cost effective and locally available option, this work focused on an easily applicable coating which utilized local resources. Toward developing such protective coating based on the locally available resources in Indonesia which can yield good corrosion resistance and thermal stability in geothermal environment, two additional components, i.e. polyaniline (PANI) and silicon dioxide, were used to modify an alkyd-based commercial coating. The selection of the alkyd-based coating as a matrix focused on the industrial convenience basis, where the coating application procedure should be simple and easy to apply within reasonable costs. The alkyd-based coating underwent severe blistering when exposed to the artificial geothermal water at 70 and 150°C due to the reaction between CaCO3 (as one of its components) and the artificial geothermal water, as well as a possible alkyd hydrolysis in the initial stage of exposure. In the oxygen-free solution, the degradation was controlled by chemical and thermal reactions, whereas in the aerated condition, oxidization at the coating surface further accelerated polymer degradation. PANI was chosen as one of the anticorrosion pigments which was widely developed over the past decades. To investigate the interaction between PANI and the artificial geothermal water, PANI film was electrochemically deposited on the carbon steel surface and exposed to the artificial geothermal water. Electrochemically synthesized oxalate-doped PANI was protective against corrosion of carbon steel in artificial geothermal water at room temperature. The mechanism involved an exchange of electroactive species within the coating layer, as confirmed by electrochemical impedance spectra. Interaction of ionic species, such as Cl-, Na+, Ca2+ from the artificial geothermal water, with the outer layer of PANI is suggested both at 25°C and 150°C, based on the EDX spectra of the coating surface after exposure to the artificial geothermal water. Thus, the protection mechanism of PANI is not solely based on the physical barrier layer properties, but rather associated with the redox mediated properties of PANI, which selectively allow ionic species intrusion from the electrolyte into the PANI layer. Although PANI is a promising candidate as an anticorrosion coating, its morphological characterization reveals that electrochemically deposited PANI is not stable for an application at 150°C. Therefore, another approach was used to promote better protective behavior of PANI by dispersing chemically synthesized PANI in the alkyd-based coating. To enhance the thermal stability of the coating, silicon dioxide (SiO2) was added, which was able to prolong the sustainability of coated metals until 28 days compared to the unmodified alkyd-based coating, which underwent a change in color to brown/orange only within 7 days of exposure. This improvement might be associated with the role of SiO2 to proportionate the thermal expansion coefficient of the coating system to be compatible with that of carbon steel. Although the coating is thermally enhanced, the electrolyte might still intrude through the coating resulting in the change of coating color after 28 days of exposure in the artificial geothermal water. When PANI was added, the coating system provided an active corrosion protection on the carbon steel surface. The chemical and morphological characterization of the PANI-alkyd and SiO2-alkyd coating system showed that coatings were improved, and no blisters were observed, albeit the degradation continued. Based on the results of exposure tests, the combined coating system was further investigated. The combinational coating of PANI/SiO2-alkyd was used with 2 wt% of PANI and 15 wt% of SiO2. Electrochemical tests indicated cathodic protection at 150°C, as the Ecorr of PANI/SiO2 remained approximately 400 mV lower than the carbon steel potential. The impedance spectra of the combinational coating of PANI/SiO2 showed a continuous decrease in the absolute impedance value over time. A significant decrease was observed within one day of exposure, followed by a slow gradual decrease, which might be associated with water absorption in the coating. FTIR spectra revealed that several peaks associated with the organic portion of the coatings were reduced after the specimens were exposed for 6 months. However, the absorption peaks related to the inorganic portion of the coatings remained stable until 6 months. Morphological characterization of the combinational coating of PANI/SiO2 showed that there were no blisters or significant discoloration of coatings after long-term exposure for 6 months in artificial geothermal water at 150°C, indicating that the chemical degradation does not significantly affect the functionality of the coating. This clearly shows the durability of PANI/SiO2 coating in the geothermal condition, suggesting that this coating can be used for such geothermal application. However, further testing of this coating should be conducted in a real geothermal environment on-site to ensure safety and viability. KW - Geothermal KW - Corrosion KW - Coating KW - Polyaniline KW - Electrochemical impedance spectroscopy PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:188-refubium-26704-6 UR - https://refubium.fu-berlin.de/handle/fub188/26704 DO - https://doi.org/10.17169/refubium-26461 SP - 1 EP - 175 CY - Berlin AN - OPUS4-51281 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Appajaiah, Anilkumar T1 - Climatic Stability of Polymer Optical Fibers (POF) N2 - Three of the five POF samples are studied more in detail to realize the effects of individual parameters and for forecasting longterm optical stability by short-term exposure tests. T3 - BAM Dissertationsreihe - 9 KW - Climatic Stability of Polymer Optical Fibers (POF) PY - 2005 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1495 SN - 978-3-86509-302-7 SN - 1613-4249 VL - 9 SP - 1 EP - 176 PB - Wirtschaftsverlag NW CY - Bremerhaven AN - OPUS4-149 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Alekseychuk, Oleksandr T1 - Detection of crack-like indications in digital radiography by global optimisation of a probabilistic estimation function N2 - A new algorithm for detection of longitudinal crack-like indications in radiographic images is developed in this work. Conventional local detection techniques give unsatisfactory results for this task due to the low signal to noise ratio (SNR ~ 1) of crack-like indications in radiographic images. The usage of global features of crack-like indications provides the necessary noise resistance, but this is connected with prohibitive computational complexities of detection and difficulties in a formal description of the indication shape. Conventionally, the excessive computational complexity of the solution is reduced by usage of heuristics. The heuristics to be used, are selected on a trial and error basis, are problem dependent and do not guarantee the optimal solution. Not following this way is a distinctive feature of the algorithm developed here. Instead, a global characteristic of crack-like indication (the estimation function) is used, whose maximum in the space of all possible positions, lengths and shapes can be found exactly, i.e. without any heuristics. The proposed estimation function is defined as a sum of a posteriori information gains about hypothesis of indication presence in each point along the whole hypothetical indication. The gain in the information about hypothesis of indication presence results from the analysis of the underlying image in the local area. Such an estimation function is theoretically justified and exhibits a desirable behaviour on changing signals. The developed algorithm is implemented in the C++ programming language and testet on synthetic as well as on real images. It delivers good results (high correct detection rate by given false alarm rate) which are comparable to the performance of trained human inspectors. N2 - In dieser Arbeit wurde ein neuer Algorithmus zur Detektion rissartiger Anzeigen in der digitalen Radiographie entwickelt. Klassische lokale Detektionsmethoden versagen wegen des geringen Signal-Rausch-Verhältnisses (von ca. 1) der Rissanzeigen in den Radiographien. Die notwendige Resistenz gegen Rauschen wird durch die Benutzung von globalen Merkmalen dieser Anzeigen erzielt. Das ist aber mit einem undurchführbaren Rechenaufwand sowie Problemen bei der formalen Beschreibung der Rissform verbunden. Üblicherweise wird ein übermäßiger Rechenaufwand bei der Lösung vergleichbarer Probleme durch Anwendung von Heuristisken reduziert. Dazu benutzte Heuristiken werden mit der Versuchs-und-Irrtums-Methode ermittelt, sind stark problemangepasst und können die optimale Lösung nicht garantieren. Das Besondere dieser Arbeit ist anderer Lösungsansatz, der jegliche Heuristik bei der Suche nach Rissanzeigen vermeidet. Ein globales wahrscheinlichkeitstheoretisches Merkmal, hier Schätzfunktion genannt, wird konstruiert, dessen Maximum unter allen möglichen Formen, Längen und Positionen der Rissanzeige exakt (d.h. ohne Einsatz jeglicher Heuristik) gefunden werden kann. Diese Schätzfunktion wird als die Summe des a posteriori Informationsgewinns bezüglich des Vorhandenseins eines Risses im jeden Punkt entlang der hypothetischen Rissanzeige definiert. Der Informationsgewinn entsteht durch die Überprüfung der Hypothese der Rissanwesenheit anhand der vorhandenen Bildinformation. Eine so definierte Schätzfunktion ist theoretisch gerechtfertigt und besitzt die gewünschten Eigenschaften bei wechselnder Anzeigenintensität. Der Algorithmus wurde in der Programmiersprache C++ implementiert. Seine Detektionseigenschaften wurden sowohl mit simulierten als auch mit realen Bildern untersucht. Der Algorithmus liefert gute Ergenbise (hohe Detektionsrate bei einer vorgegebenen Fehlalarmrate), die jeweils vergleichbar mit den Ergebnissen trainierter menschlicher Auswerter sind. T3 - BAM Dissertationsreihe - 18 KW - object detection KW - detection of elongated objects in low SNR condition KW - dynamic programming PY - 2006 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1400 SN - 978-3-86509-534-8 SN - 1613-4249 VL - 18 SP - 1 EP - 114 PB - Wirtschaftsverlag NW CY - Bremerhaven AN - OPUS4-140 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -