TY - THES A1 - Weißhaupt, Petra T1 - Nitrogen uptake of saprotrophic basidiomycetes and bacteria N2 - Saprotrophe Basidiomyceten können unter aeroben Bedingungen Holz abbauen und wirtschaftliche Schäden verursachen. Die Stickstoffverfügbarkeit ist für diesen Abbau entscheidend, und diazotrophe Bakterien können durch Fixierung von atmosphärischem N2 Stickstoff auf Holz anreichern. Der gemeinsame Abbau durch Basidiomyceten und Diazotrophe könnte zu hohen Abbauraten führen, da N2-Fixierung große Mengen an ATP benötigt, welche durch Celluloseabbau regeneriert werden. In dieser Arbeit wurde diese Interaktion durch Messungen des Stickstoffanteils sowie der δ15N-Werte in der Biomasse untersucht. Außerdem wurde die Aktivität der Basidiomyceten unter Einfluss unterschiedlicher Stickstoffquellen bestimmt. Die Messungen des Stickstoffanteils in der Biomasse der Basidiomyceten Oligoporus placenta und Trametes versicolor bewiesen die Aufnahme organischen Stickstoffs, sogar wenn nur Spuren verfügbar waren. Darüber hinaus förderten Harnstoff und Ammoniumchlorid das Wachstum von T. versicolor. In Experimenten unter einer 15N2/O2-Atmosphäre wurde ermittelt, dass die diazotrophen Bakterien Azotobacter croococcum, Beijerinckia acida und Novosphingobium nitrogenifigens etwa 1– 13% ihres Stickstoffbedarfs durch N2-Fixierung decken. Wurden Diazotrophe und Basidiomyceten gemeinsam kultiviert,konnte nur von B. acida N2 fixiert und an beide Basidiomyceten übertragen werden. A. croococcum und N. nitrogenifigens wiesen keine Aktivität auf. Die Effekte der drei Stickstoffquellen, organischer Stickstoff im Medium, organischer Stickstoff in Splintholz sowie N2 aus der Luft, auf die Biomasse der Basidiomyceten wurden in Experimenten nach einem statistischen Versuchsplan bestimmt. Organischer Stickstoff als Medienbestandteil förderte das Wachstum beider Basidiomyceten signifikant. In zwei weiteren Versuchsreihen wurde die Stickstoffquelle im Medium durch das Bakterium B. acida ersetzt. Luftstickstoff begünstigte das Bakterienwachstum, so dass die Biomassen der Basidiomyceten gegenüber N2-freien Bedingungen verringert wurden. Das Vorhandensein von B. acida hatte einen geringfügig fördernden Effekt auf die Biomasse von T. versicolor aber keinen Effekt auf die Biomasse von O. placenta. Im Gegensatz zu den zuvor genannten Organismen kommen Hypholoma fasciculare und einige, teils isolierte und charakterisierte Proteobakterien gemeinsam in der Natur vor. Das Wachstum der Biomasse von H. fasciculare und von Proteobakterien wurde durch organischen Stickstoff, Harnstoff und Ammoniumchlorid gefördert. Die N2-Fixierung der Proteobakterien war zwar signifikant jedoch geringfügig, so dass sie mit Adsorption an Stelle von Nitrogenaseaktivität interpretiert wurde. Die Konkurrenz von H. fasciculare und Proteobakterien um die gleichen Stickstoffquellen wurde als wahrscheinlicher betrachtet als die Stickstoffanreicherung durch Diazotrophie. N2 - Saprotrophic basidiomycetes decompose wood in aerobic environments and can cause economic damage. The availability of nitrogen is determining for decomposition, and diazotrophic bacteria might enhance the nitrogen availability by fixation of atmospheric N2. Simultaneous decomposition by basidiomycetes and diazotrophs may intensify decomposition, because N2 fixation requires ATP, which could be provided during cellulose decomposition. In this study, the interaction was analysed by measurements of the nitrogen content and the δ15N values in biomass. Besides, the activity of basidiomycetes, influenced by different nitrogen sources, was determined. The analysis of the nitrogen content in biomass of Oligoporus placenta and Trametes versicolor proved the efficient uptake of organic nitrogen by wood-decomposing fungi even if only traces were available. In the presence of urea and ammonium chloride, the growth of T. versicolor was intensified. At cultivations in a 15N2/O2 atmosphere, the diazotrophic bacteria Azotobacter croococcum, Beijerinckia acida and Novosphingobium nitrogenifigens covered 1 to 13% of the nitrogen in their biomass by N2 fixation. If basidiomycetes and diazotrophs were co-cultivated, only B. acida fixed N2 and transferred it to both fungi. A. croococcum and N. nitrogenifigens did not coexist with the fungi. The effects of the nitrogen sources, i.e., organic nitrogen in the medium, organic nitrogen in sapwood and N2 from air, on the biomass of the mentioned basidiomycetes were determined in experiments according to full-factorial experimental plans. Organic nitrogen in the medium increased the growth of both basidiomycetes significantly. In additional experiments, the nitrogen source in the medium was replaced by an inoculum of B. acida. Then, atmospheric N2 supported the bacterial growth, which caused a significant decrease of basidiomycetal biomass compared to N2-free conditions. The presence of B. acida increased the biomass of T. versicolor to a low extent, but had no effect on the biomass of O. placenta. In contrast to the previously mentioned organisms, Hypholoma fasciculare and proteobacteria occur together in nature. In experiments, the growth of biomass of H. fasciculare and proteobacteria was supported by organic nitrogen, urea and ammonium chloride. The N2 fixation of the bacteria was significant but amounted to a low extent and was therefore explained by adsorption and not by nitrogenase activity. Competition between H. fasciculare and proteobacteria for the same nitrogen sources appeared more probable than N enrichment by diazotrophic activity. T3 - BAM Dissertationsreihe - 87 KW - Holz KW - Diazotrophe KW - Basidiomyceten KW - IRMS KW - 15N2 PY - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-716 SN - 978-3-9815134-2-4 SN - 1613-4249 VL - 87 SP - 1 EP - 98 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-71 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Nies, Daniel T1 - Entwicklung eines Prüfverfahrens zur laserinduzierten thermischen Ermüdung thermischer Schutzschichten mittels einer Laser-Thermoschockprüfeinrichtung N2 - Die Endlichkeit fossiler Brennstoffe und das steigende Umweltbewusstsein sind die immer stärker werdenden Motivationen für die Entwicklung von effizienteren Gasturbinen und Triebwerken zur Energieerzeugung oder zum Antrieb von Land-, Luft- und Seefahrzeugen. Eins der dafür entwickelten Konzepte ist das der thermischen Schutzschichten. Dabei kann durch den Auftrag einer keramischen Schicht die thermische Belastung der beschichteten Bauteile reduziert werden. In dieser Arbeit wird die Möglichkeit der Nutzung einer Laser-Thermoschock-Prüfeinrichtung zur Durchführung von thermo-zyklischen Versuchen an thermischen Schutzschichten untersucht. Die Probenerwärmung erfolgt hierbei durch einen fokussierten Laserstrahl, mit dem durch die gewählte Trajektoriengeometrie und Anpassung der Laserleistung eine homogene Temperaturverteilung auf der Oberflache erzeugt wird. Die für die Durchführung von zyklischen Versuchen notwendigen Erweiterungen der vorhandenen Prüfeinrichtung werden beschrieben, wozu die Entwicklung eines neuen Probenhalters und einer Test- und Auswerteroutine für die Experimente gehört. Zur Begutachtung der Entstehung und des Fortschritts von Schädigungen werden Schallemissionstechniken und thermografische Methoden eingesetzt, deren Möglichkeiten und Grenzen für die Nutzung im Rahmen der Experimente bestimmt werden. Außerdem umfasst die Arbeit eine umfassende temperaturabhängige Charakterisierung des für die thermische Schutzschicht verwendeten keramischen Materials. Hierbei ist besonders die Messung des E-Moduls mittels der dynamischen Resonanzmethode hervorzuheben, die eine selten genutzte Technik ist. Bei der Charakterisierung zeigen sich keine besonderen Abweichungen von den erwarteten Werten. Lediglich eine geringere Porosität als vom Hersteller erwartet und eine unveränderte Phasenzusammensetzung nach isothermer Auslagerung wurden beobachtet. Die bei den zyklischen Experimenten angestrebten Oberflächentemperaturen von über 1000 °C machen es nötig, die Absorption der Proben durch eine zusätzliche Beschichtung mit Magnetit zu erhöhen. Zur Messung der Temperaturverteilung auf der Probenoberfläche wird eine Infrarot- Kamera genutzt, die für diese Zwecke kalibriert wird. Die eingebaute aktive Druckluftkühlung der Probenruckseite erlaubt die Steuerung des Temperaturgradienten, besitzt aber noch Verbesserungspotenzial. Schon ohne aktive Kühlung der Proben ist ein Versuchsregime realisierbar, bei dem die thermischen Belastungen mit hoher Präzision reproduzierbar sind und mit dem die realen Einsatzbedingungen von keramischen Schutzschichten nachempfunden werden können. Die Entstehung und der Fortschritt von Schädigungen in Form von Delaminationen kann mit thermografischen Methoden und Schallemissionstechniken beobachtet werden. Bei der Ortung der Schallsignale zeigen sich die Grenzen der vorhandenen Ausrüstung. Eine relativ genaue Ortung der Quelle ist mit einer zeitaufwendigen manuellen Routine möglich, deren Ergebnis eine starke Abhängigkeit von der Signalqualität zeigt. Eine reduzierte Zonenortung mit einer automatischen Auswertung zeigt zufriedenstellende Ergebnisse. Eine Kombination der Ergebnisse der Zonenortung, der Analyse der Schallsignale und den thermografischen Analysen der Daten der Infrarot-Kamera ermöglicht eine sehr gute Visualisierung der Schädigungsentwicklung. Während erster Versuche konnten Delaminationsrisse in der keramischen Dammschicht erzeugt werden, die in der Nähe der Dammschicht-Haftschicht-Grenzschicht liegen. Dies entspricht einem Schadensbild, das durch eine hohe zyklische Belastung der Proben erreicht wird. Durch die Nutzung eines fokussierten Laserstrahls kommt es zu einer Temperaturüberhöhung im Bereich des Laserspots. Dies bewirkt, dass die thermozyklische Belastung der Proben noch um einen Thermoschockbeitrag erweitert wird. N2 - The finite nature of fossil fuel supply and the growing environmental awareness become increasingly stronger motivations for the development of efficient gas turbines and jet engines for power generation or as engines for land-, sea- and water-based vehicles. One concept developed for this purpose are thermal barrier coatings, where the thermal load of components is reduced by applying a ceramic coating onto the components. In this work the possibility to use a laser thermal shock facility for thermo-cyclic testing of thermal barrier coatings is examined. A focused laser beam is used for heating the sample and a homogeneous temperature distribution on the sample surface is achieved by the used trajectory and radial adjusted laser power. The required improvements of the existing testing facility are explained, including the development of a new sample holder and of the testing and evaluation routines for the experiments. For the assessment of the initiation and evolution of damages, acoustic emission and thermographic methods are used. The possibilities and limits of these methods are assessed during the experiments. The work also includes an extensive temperature dependent characterisation of the ceramic material used for the thermal barrier coating. In this part, the measurement of the Young’s modulus by a dynamic method is to be highlighted, as this is a rarely used technique. The characterisations show the expected values, except for a lower porosity as expected by the manufacturer and no significant phase changes during isothermal heat treatments. To reach sample surface temperatures above 1000 °C, it is necessary to increase the absorption by an additional coating of magnetite. The temperature distribution on the surface is measured by an infrared camera, which is calibrated for this purpose. With the incorporated active air cooling of the sample backside, the temperature gradient can be controlled, but still leaves room for improvements. Already without cooling, experiments can be completed, where the thermal loads are highly reproducible and comparable to real operation conditions. The development and evolution of delamination damages can be observed by acoustic Emission and thermographic methods. Sound location using the acoustic emission data shows the limits of the applied equipment. Good sound location results can be achieved by a time-consuming manual routine, but the results are highly dependent on the signal quality. A reduced zone location algorithm with an automatic analysis shows satisfying results. A combination of the zone location results, the analysis of the acoustic emission data and the thermographic analysis of the infrared camera data allows a very good visualisation of the damage evolution. First experiments showed delaminations located in the ceramic layer near the topcoat-bondcoatboundary, which corresponds to a failure mode induced by high cyclic loads of the samples. The use of a focused laser beam results in a local hot spot at the laser spot during heating. This adds a thermal shock component to the thermo-cyclic load during the experiments. T3 - BAM Dissertationsreihe - 84 KW - Thermische Schutzschichten KW - laserinduzierte Erwärmung KW - Schallemission KW - Thermografie KW - Yttrium stabilisiertes Zirkonoxid PY - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-740 SN - 978-3-9814634-8-4 SN - 1613-4249 VL - 84 SP - 1 EP - 143 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-74 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Jaunich, Matthias T1 - Tieftemperaturverhalten von Elastomeren im Dichtungseinsatz N2 - Elastomerdichtungen finden als Bauteil oder Maschinenelement vielseitige Verwendung. Jedoch war trotz ihrer zentralen Bedeutung die untere Temperaturgrenze, bis zu der solche Dichtungen eingesetzt werden können, bisher nicht tiefgehend verstanden. Dieser Umstand erschwert die entsprechende notwendige sicherheitsrelevante Beurteilung. Mit der vorliegenden Arbeit ist deshalb das Ziel verfolgt worden, dass Materialverhalten repräsentativer Elastomerwerkstoffe in Abhängigkeit von der Temperatur zu verstehen und daraus dann abzuleiten, bis zu welcher Temperatur eine daraus hergestellte Dichtung unter Berücksichtigung der jeweiligen Einsatzbedingungen ihre Funktion noch sicher erfüllen kann. Ausgehend von der in der Literatur beschriebenen Aussage, dass eine Dichtung auch unterhalb der „Glasübergangstemperatur“ funktionsfähig ist, wurde der Einfluss des Glas-Gummi-Übergangs auf das Dichtungsversagen untersucht. Zunächst wurden dazu die Glasübergangstemperaturen an einer Vielzahl von Elastomeren mit gebräuchlichen Verfahren bestimmt, um diese mit dem Verhalten der Dichtung vergleichen zu können. Weiterhin wurde im Rahmen der Arbeit eine neue Charakterisierungsmethode des Tieftemperaturverhaltens von Elastomeren entwickelt, die die bisher für Dichtungen eingesetzte Normprüfung des Druckverformungsrests nachstellt. Mit dieser Methode ist im Vergleich zur Normprüfung jedoch eine deutlich schnellere und automatisierbare Untersuchung des Materialverhaltens gegeben. Darüber hinaus ist durch eine modellgestützte Auswertung eine Extrapolation der Messdaten auf zusätzliche Temperaturen möglich, wodurch der experimentelle Aufwand weiter reduziert wird. Zur temperaturabhängigen Charakterisierung des Versagensvorgangs an realen Bauteilen wurde deren Dichtverhalten mittels eines dafür entwickelten Versuchsstandes untersucht. Die festgestellte Abhängigkeit der Versagenstemperatur vom Verpressgrad konnte unter Verwendung der Ergebnisse aller angewandten Charakterisierungsmethoden für die hier untersuchten statisch beanspruchten Dichtungen erklärt werden. Zudem lassen sich aus dem mit Hilfe des Zeit-Temperatur- Superpositionsprinzips gewonnenen Informationen zur Zeitabhängigkeit der Materialeigenschaften auch Aussagen zum Verhalten von dynamisch beanspruchten Dichtungen ableiten. Mit dem Ergebnis der Arbeit zum Verständnis des Verhaltens von Elastomerdichtungen bei tiefen Temperaturen wird die gezielte Beurteilung und Auswahl von sicherheitsrelevanten Dichtsystemen in Zukunft vereinfacht. N2 - Elastomeric seals are of high importance as machine parts and construction elements, but in spite of this the low temperature limit for the use of a seal was not fully understood. Hence, the required safety relevant evaluation of the lowest acceptable operating seal temperature is difficult. Therefore the presented work was aimed to understand the temperature dependent material behaviour of representative elastomers and to conclude from this knowledge the low temperature limit down to which such seals could safely fulfil the desired requirements. Starting with the published statement that a seal can safely work below its glass Transition temperature the influence of the glass-rubber-transition was investigated. At first the glass-rubber-transition temperatures of the selected elastomers were determined applying several techniques to allow a comparison with the behaviour of the seals during component tests. Furthermore a new method to characterise the low temperature behaviour of elastomers was developed that emulates the key features of the standardised compression set test used for seal materials. In comparison to the standardized test this new method allows a much faster measurement that can be automatically performed. Using a model based data analysis an extrapolation of the results to different temperatures can be performed and therefore the necessary measuring expenditure can be additionally reduced. For the temperature dependent characterisation of the failure process of real seals a measurement setup was designed and the materials behaviour was investigated. By use of the results of all applied characterisation techniques the observed dependence of the failure temperature on the degree of compression could be explained for the investigated seals under static load. Additionally information about the behaviour of such seals under dynamic load could be gained from the time dependent material behaviour by use of the time temperature superposition relationship. By application of the gained insight into the behaviour of elastomeric seals at low temperatures the evaluation and selection of safety relevant seal systems will be simplified in the future. T3 - BAM Dissertationsreihe - 79 KW - leakage rate KW - Elastomer KW - Dichtung KW - Tieftemperaturverhalten KW - Glas-Gummi-Übergang KW - Leckagerate KW - seal, rubber KW - low temperature behavior KW - glass-rubber transition PY - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-794 SN - 978-3-9814634-3-9 SN - 1613-4249 VL - 79 SP - 1 EP - 153 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-79 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Schlichting, Joachim T1 - Integrale Verfahren der aktiven Infrarotthermografie N2 - Die zerstörungsfreie Prüfung ist eine Aufgabe von großer Bedeutung, sowohl aus wirtschaftlicher Perspektive, als auch um die notwendige Sicherheit technischer Systeme gewährleisten zu können. Mit der Thermografie steht eine schnelle und berührungslose Prüftechnik zur Verfügung, die nicht zuletzt wegen der rapiden Entwicklung auf dem Gebiet der Infrarotkameras in letzter Zeit große Aufmerksamkeit erfährt. Typischerweise werden thermografisch oberflächennahe, parallel zur Oberfläche ausgedehnte Defekte nachgewiesen. In dieser Arbeit werden zwei untypische Prüfprobleme gelöst. An Punktschweißverbindungen wird mit der Linsengröße eine Struktur in der Mitte der Probe mittels Blitzlichtthermografie indirekt vermessen. Hier können typische Fehlerbilder wie Klebverbindungen und Spritzer sicher erkannt werden, was statistisch abgesichert durch eine Serienmessung und den Vergleich mit zerstörender Prüfung gezeigt wird. Ein Beispiel für orthogonal zur Oberfläche orientierte Fehlstellen stellen Risse dar, wie sie beispielsweise in Schweißnähtenn häufig auftreten. Neben der Entwicklung eines Verfahrens zur Detektion von Rissen, welches auf kommerziell erhältlichen Geräten aufbaut, wurde in Experimenten und Finite-Elemente-Simulationen untersucht, inwieweit sich auch die geometrischen Eigenschaften bestimmen lassen. Mit einem Verfahren, das ebenso wie die Methode zur Prüfung der Schweißpunkte auf der Analyse zeitlich und räumlich integraler Größen basiert, die vom thermischen Widerstand abhängen, ist die gleichzeitige Bestimmung von Winkel und Tiefe möglich. N2 - Non-destructive evaluation is a task of utmost importance for both, the economic point of view and to guarantee the required safety and reliability of technical systems. Thermography is a fast and contactless technique which received continued attention not least through the significant price drop at the infrared camera market. It is typically used to detect near-surface defects which are expanded parallel to the surface. This thesis deals with two non-standard inspection tasks. With the weld lens diameter of spot welds, a feature in the sample's geometrical center is indirectly sized by ash thermography. The presented method is suitable to distinguish typical error classes like stick welds or expulsions. This fact is validated by statistical evaluations of thermographic and destructive test series. As an example for perpendicularly oriented imperfections, surface cracks are investigated, which can be a major problem at welding seams. A technique for detecting cracks entirely based on commercially available equipment is developed. In addition, the accessibility of geometric characteristics of cracks was examined by experiments and FEM-simulations. Similar to the method developed for assessing spot welds, an approach based on the analysis of spatial and temporal integral quantities which depend on the thermal resistance is used. In doing so, the simultaneous determination of crack angle and depth is possible. T3 - BAM Dissertationsreihe - 91 KW - Aktive Thermografie KW - FEM KW - Spot Welding KW - Cracks KW - Nondesstructive Evaluation KW - Active Thermography KW - Zerstörungsfreie Prüfung KW - Punktschweißen KW - Risse KW - FEM PY - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-676 SN - 978-3-9815134-6-2 SN - 1613-4249 VL - 91 SP - 1 EP - 209 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-67 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Seefeldt, Henrik T1 - Flame retardancy of wood-plastic composites N2 - Über das Brandverhalten von „Wood-plastic Composites“ (WPCs) und deren Flammschutz ist bislang wenig bekannt. Die Verwendung von WPCs ist in den vergangenen Jahren stetig gestiegen. Vor allem in ihrem Hauptanwendungsgebiet als Bodenbeläge verzeichnen WPC Materialien einen großen Marktanteil. Bis jetzt existiert jedoch noch keine Flammschutzlösung, die alle nötigen Anforderungen im Bauwesen erfüllt. Flammgeschützte Materialien sind jedoch vor allem für Innenanwendungen und im Bereich von Fluchtwegen unabdingbar. In dieser Arbeit werden zum einen grundlegende Mechanismen über das Brandverhalten von WPCs aufgeklärt. Zum anderen werden die Wirksamkeit und die Wirkungsweise verschiedener Flammschutzmitteln in WPC Materialien untersucht. Ein spezielles Augenmerk wird dabei auch auf Endprodukte aus WPC Materialien gelegt. WPC wurde dabei in seiner Hauptanwendung als Fußbodenbelag untersucht. Das Brandverhalten wurde für Materialien und Produkte mit Hilfe von „Cone Calorimeter“ Untersuchungen und „Radiant Panel Tests“ bestimmt. Zudem wurden numerische Simulationen genutzt, um den Einfluss verschiedener thermischer Materialparameter auf das Brandverhalten zu erforschen. Desweiteren wurde das thermische Zersetzungsverhalten mittels thermogravimetrischer Methoden und spektroskopischen Untersuchungen ermittelt. Auf dessen Grundlage konnten Abbaumechanismen für WPC Materialen in Verbindung mit verschiedenen Flammschutzmitteln erstellt werden. WPCs zeigen das gleiche Brandverhalten wie Holz, auf Grund des polymeren Anteils ist jedoch die Wärmefreisetzungsrate während der Verbrennung stark erhöht. Es konnte gezeigt werden, dass alle untersuchten Flammschutzmittel einen positiven Effekt auf das Brandverhalten von WPCs hatten. Beste Ergebnisse wurden durch Ammonium-Polyphosphat, Paxymer und expandierbaren Graphit erzielt. Expandierbarer Graphit war besonders in Verbindung mit rotem Phosphor sehr wirksam, da der Phosphor den gebildeten Rückstand stabilisierte. Neben dem Einfluss von Flammschutzmitteln konnte gezeigt werden, dass für WPC Fußbodendielen auch andere Einflussfaktoren, wie die Geometrie und der Feuchtigkeitsgehalt eine wichtige Rolle spielen. So weisen Hohlkammerprofildielen im Vergleich zu Vollprofilproben zwar eine verminderte Menge an brennbarem Material auf, die Flammenausbreitung ist jedoch stark erhöht. N2 - Up to now only little knowledge has been recorded about the fire behavior and flame retardancy of wood-plastic composites (WPCs). The use of WPCs has increased continuously in recent years. Especially in their main field of application as a decking material, WPCs present a big share of the market. To date no flame-retarded solution has been introduced for WPC materials that fulfils the necessary requirements. But flameretarded materials are indispensable, especially for indoor use and the protection of escape routes. In this study basic knowledge about the fire behavior of WPCs is investigated first. Second, the effectiveness and mode of action of different flame-retardant additives is investigated. Special attention is drawn to products made of WPC material. Therefore WPC was further investigated in its main field of application as decking boards. The fire behavior of materials and products was investigated by means of cone calorimeter measurements as well as radiant panel tests. Furthermore numerical simulations were carried out to study the effects of various thermal material properties on burning behavior. Thermal decomposition was studied using thermogravimetric methods and spectroscopic investigations. Against this background, models for thermal decomposition pathways were built for combinations of WPC material with different flame retardants. WPCs show burning behavior similar to that of pure wood samples with an increased heat release rate due to polymeric fractions. It is shown that all investigated flame retardants had a positive effect on the burning behavior of WPCs. The best results were achieved by the flame retardants ammonium polyphosphate, Paxymer and expandable graphite. Especially in combination with red phosphorus, expandable graphite was highly effective because red phosphorus stabilized formed residue. Apart from the influence of flame retardants, other influencing factors like geometry and moisture content also played an important role concerning the flame retardancy of WPC decking boards. Indeed, hollow decking boards offer a reduced amount of combustible material, but their flame spread is increased in comparison to solid samples. T3 - BAM Dissertationsreihe - 90 PY - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-684 SN - 978-3-9815134-5-5 SN - 1613-4249 VL - 90 SP - 1 EP - 107 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-68 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR T1 - Amts- und Mitteilungsblatt, Band 42, Heft 2 T3 - Amts- und Mitteilungsblatt der BAM - 2/2012 PY - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-119 SN - 0340-7551 VL - 42 IS - 2 SP - 1 EP - 151 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-11 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR T1 - Amts- und Mitteilungsblatt, Band 42, Heft 1 T3 - Amts- und Mitteilungsblatt der BAM - 1/2012 PY - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-129 SN - 0340-7551 VL - 42 IS - 1 SP - 1 EP - 49 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-12 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR T1 - Amts- und Mitteilungsblatt, Band 42, Heft 4 T3 - Amts- und Mitteilungsblatt der BAM - 4/2012 PY - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-97 SN - 0340-7551 VL - 42 IS - 4 SP - 1 EP - 187 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-9 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR T1 - Amts- und Mitteilungsblatt, Band 42, Heft 3 T3 - Amts- und Mitteilungsblatt der BAM - 3/2012 PY - 2012 U6 - http://nbn-resolving.de/urn/resolver.pl?urn:nbn:de:kobv:b43-109 SN - 0340-7551 VL - 42 IS - 3 SP - 1 EP - 375 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-10 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schartel, Bernhard T1 - Towards evidence-based development of flame retarded polymers T2 - 243rd National ACS meeting - Spring 2012 CY - San Diego, CA, USA DA - 2012-03-25 KW - Flame retardancy KW - Halogen-free KW - Flame retardancy mechanism KW - Fire property assessment PY - 2012 SN - 978-0-8412-2727-9 SN - 1550-6703 N1 - Serientitel: PMSE Preprints – Series title: PMSE Preprints VL - 243 SP - 38-PMSE PB - Amer Chemical SOC CY - Washington, USA AN - OPUS4-26381 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Schartel, Bernhard A1 - Richter, K. H. A1 - Böhning, Martin ED - Morgan, A. B. ED - Wilkie, C. A. ED - Nelson, G. L. T1 - Synergistic use of talc in halogen-free flame retarded polycarbonate/Acrylonitrile-butadiene-styrene blends N2 - Pyrolysis, flammability, fire behavior, melt viscosity, and gas diffusion of bisphenol A polycarbonate/acrylonitrile-butadiene-styrene (PC/ABS) were investigated, with bisphenol A bis(diphenyl phosphate) (BDP), with 10 wt.% talc and with BDP in combination with 5, 10 and 20 wt.% talc, respectively. Compared to PC/ABS, PC/ABS + BDP results in an increased decomposition temperature of PC, a higher char yield, a significantly increased LOI, a V-0 classification in UL 94, a reduced peak heat release rate (pHRR), and a reduced total heat release (THR) in the cone calorimeter. This efficient flame retardancy is due to mechanisms in both the gas and condensed phases. PC/ABS + 10 wt.% talc shows a decrease in the PC decomposition temperature. The fire behavior is improved in part compared to PC/ABS, with an increased LOI and reduced pHRR. PC/ABS + BDP + 10 wt.% talc shows a strong synergism in LOI, a V-0 classification, and a decrease in pHRR, whereas THR is slightly increased compared to PC/ABS + BDP. Talc decreases the gas diffusion and enhances the flow limit for low shear rates, both of which influence the pyrolysis and flammability results. Further, talc improves the protection properties of the fire residues. Nevertheless it also partly suppresses flame inhibition and the charring effect of BDP. The synergism between BDP and talc in LOI is obtained even for low talc loadings in PC/ABS + BDP + talc, whereas for higher loadings saturation is observed. KW - Flame retardancy KW - PC/ABS KW - Aryl phosphate KW - Talc PY - 2012 SN - 978-0-8412-2780-4 U6 - https://doi.org/10.1021/bk-2012-1118.ch002 N1 - Serientitel: ACS Symposium Series – Series title: ACS Symposium Series VL - 1118 IS - Chapter 2 SP - 15 EP - 36 PB - Oxford University Press AN - OPUS4-27563 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herbst, Tristan A1 - Rübner, Katrin A1 - Meng, Birgit T1 - Integrated and holistic suitability assessment of recycling options for masonry rubble N2 - Behandelt den Bausektor und die Verarbeitsungsqualität T2 - European Geosciences Union (EGU) General Assembly 2012 CY - Vienna, Austria DA - 22.04.2012 PY - 2012 AN - OPUS4-25868 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herbst, Tristan A1 - Rübner, Katrin A1 - Müller, A. A1 - Seidemann, M. T1 - Verwertung kieselsäurehaltiger Filterrückstände in mineralischen Baustoffen N2 - - jährlicher Anfall von 5.000 bzw. 10.000 Tonnen wasserhaltiger Filterrückstände (FR) pro Produzent bei der Abwasser-Neutralisation aus der Kieselsäure- bzw. Chlorsilanherstellung (FR1, FR2) - heute: Deponierung, Tagebauverfüllung - ungenutzte Sekundärrohstoffquelle - Untersuchung möglicher Anwendungsbereiche für FR T2 - GDCh Tagung Bauchemie CY - Dübendorf, Switzerland DA - 11.10.2012 PY - 2012 AN - OPUS4-26673 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rübner, Katrin A1 - Meinel, Dietmar A1 - Prinz, Carsten A1 - Zimathies, Annett A1 - Klobes, Peter A1 - Schnell, A. A1 - Hempel, S. T1 - Porenstruktur leichter Gesteinskörnungen aus Mauerwerkbruch N2 - Leichte Gesteinskörnungen mit Kornrohdichten < 2 g/cm³ werden industriell aus natürlichen Rohstoffen, wie Ton und Schiefer, hergestellt. Dabei fallen hohe Energiekosten an, während außerdem fortwährend die Verfügbarkeit geeigneter Rohstoffe sinkt. Eine Alternative stellen Leichtgranulate, die aus mineralischen Bau- und Abbruchabfällen hergestellt werden, dar. Im Forschungsprojekt „Aufbaukörnungen“ wurde eine Technologie zur Herstellung hochwertiger leichter Gesteinskörnungen aus Mauerwerkbruch entwickelt. Ziegelhaltige Bau- und Abbruchabfälle fallen in Deutschland mit bis zu 26 Mio. t pro Jahr an und weisen größere Verwertungsdefizite als Betonbruch auf. Der neuen Verwertungsstrategie liegt die Idee des rohstofflichen Recyclings zu Grunde. Die leichten Gesteinskörnungen werden am Ende eines mehrstufigen Herstellungsprozesses durch thermische oder hydrothermale Erhärtung im Labor- und halbtechnischen Maßstab produziert. Für Herstellungstechnologie und Eigenschaften der Leichtbetone sind neben Kornfestigkeit und Rohdichte die Porosität und Wasseraufnahme der leichten Gesteinskörnungen entscheidende Größen, die wiederum von Kornform, Oberflächenrauigkeit, Sinterschale und Porenstruktur der Körnungen beeinflusst werden. T2 - XVI. Porotec-Workshop über die Charakterisierung von feinteiligen und porösen Festkörpern CY - Bad Soden, Germany DA - 13.11.2012 PY - 2012 AN - OPUS4-27160 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Daum, Werner A1 - Tkachenko, Viktoriya A1 - Habel, Wolfgang T1 - Sensitive pultrudierte Tragwerke N2 - - Innovative Konstruktionskonzepte für den Leichtbau verwenden neue Material-Kombinationen - Erweiterte Anwendung der Sensortechnik bei der Entwicklung neuer Materialen - Integration von Sensoren in die Struktur, um synergetische Effekte effizienter auszunutzen und Eigenschaften zu steuern T2 - 2. TSB-TransferTreff "Materialeffizienz und Gestaltung" CY - Berlin, Germany DA - 11.06.2012 PY - 2012 AN - OPUS4-26464 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Woydt, Mathias A1 - Scholz, C. A1 - Burbank, J. A1 - Spaltmann, Dirk T1 - Slip-rolling resistant steel alloys up to P0max of 3,920 MPa N2 - Downsizing (power-to-weight ratio) and higher speeds lead to a rise in Hertzian contact pressures in combination with an increase in surface or oil temperatures. Under such conditions, commonly used bearing steels, such as 100Cr6, reach their limits, creating a demand for alternative slip-rolling resistant steel alloys. The present work therefore compares the slip-rolling performance of various steel types with Maraging- and PM-type steel alloys such as e.g. CSS-42L™, ASP2012, BIMAX42+, in the Hertzian contact pressure range up to P0max of 4 GPa. Through-hardened 100Cr6H (AISI 52100), case-hardened 20MnCr5 (AISI 5120H) and nitrogen alloyed Croni-dur30 (AMS 5898) still compete in terms of slip-rolling and wear resistance and load carrying capacity, whereas Maraging- and PM-type steel alloys offer superior strength and toughness properties. KW - Steel KW - Alloy KW - Slip-rolling KW - Friction KW - Wear rate KW - Contact pressure KW - 100Cr6 KW - BIMAX42 KW - CSS-42L KW - ASP20212 PY - 2012 U6 - https://doi.org/10.1016/j.wear.2021.203707 VL - 474-475 SP - 203707 PB - Elsevier B.V. AN - OPUS4-52549 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maurer, G. A1 - Tuma, Dirk A1 - Chobanov, K. A1 - Kumełan, J. A1 - Pérez-Salado Kamps, Á. T1 - Gas solubility in ionic liquids: Solubility of a binary gas mixture in a pure ionic liquid as well as of a single gas in a binary liquid mixture N2 - Ionic Liquids (ILs) are employed in various fields, for example, reaction engineering (reactions with gases, such as hydroformylation (CO, H2), hydrogenation (H2), oxidation (O2)) or separation technology (separations of gases, reactants, and high-volatility reaction products). For the basic engineering of such processes, knowledge of phase equilibria, particularly of mixtures, over a broad (p,T) range is mandatory. This contribution reports on recent experimental results from our laboratory: – for the simultaneous solubility of a binary gas mixture in a pure ionic liquid – for the solubility of a single gas in a binary liquid solvent mixture. T2 - EUCHEM 2012 Conference on Molten Salts and Ionic Liquids CY - Celtic Manor, Wales, United Kingdom DA - 05.08.2012 KW - ionic liquids KW - gas solubility KW - Henry's constant PY - 2012 AN - OPUS4-35947 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nolze, Gert T1 - Fast Orientation Projection using OpenGL N2 - Electron backscatter diffraction produces an enormous number of single orientation data which need to be processed but also visualized. The presentation shows that standard hardware can be used to increase the presentation speed considerably. T2 - EBSD 2012 CY - Pittsburgh, Pennsylvania, USA DA - 19.06.2012 KW - electron backscatter diffraction KW - OpenGL KW - crystal orientation KW - pole figure PY - 2012 AN - OPUS4-37900 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Payton, E. A1 - Nolze, Gert T1 - The BSE signal as an additional tool for phase assignment in EBSD N2 - The presentation demonstrates how the background signal of EBSD patterns can be used for a rough assignment of phases which cannot distinguished by the diffraction signal. T2 - EBSD 2012 CY - Pittsburgh, Pennsylvania, USA DA - 19.06.2012 KW - Electron backscatter diffraction KW - Backscattered electrons KW - Kikuchi pattern KW - Phase distribution KW - Phase separation KW - Phase recognition PY - 2012 AN - OPUS4-37901 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nolze, Gert A1 - Saliwan Neumann, Romeo A1 - Buchheim, Michaela T1 - Microstructure investigations of iron meteorites by EBSD and EDS analyses N2 - Meteorites are a unique and inspiring material for microstructural studies because if their very specific genesis. Iron meteorites have been formed under unimaginable cooling rates of a few ten Kelvins per million years so that the observable transformation of the formerly huge Fe-Ni single crystals of taenite occurred under nearly-equilibrium conditions. Octahedrites (meteorites having a Ni content between 6...15%) are characterized by ribbons of the low-temperature Fe-Ni phase kamacite separated by rims of residual taenite. This very specific feature is known as Widmanstaetten structure and has been investigated by synchrotron radiation in order to cover a higher volume fraction for a statistically relevant description of orientation relationships. However, plessite – a microstructure mainly consisting of the same phases – reflects the orientation relationship between kamacite and taenite as well. For their characterization, a scanning electron microscope is very suitable in order to investigate crystal orientations or identify phases. Despite the apparently ideal formation circumstances of iron meteorites, Ni concentration profiles prove non-equilibrium conditions. Combined EDS (energy dispersive spectroscopy) and EBSD (electron backscatter diffraction) measurements at a selected plessitic region of the Cape York iron shows that a correlation exists between Ni-concentration and the locally detected orientation relationship. T2 - 15th European Microscopy Congress CY - Manchester, UK DA - 16.09.2012 KW - Phase identification KW - Corrosion KW - Chloride KW - Dermbach PY - 2012 SP - 90 AN - OPUS4-37775 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -