TY - CONF A1 - Oster, Simon A1 - Mann, S. A1 - Sharma, R. A1 - Reisgen, U. T1 - In-situ Identifikation der Schweißnahtgeometrie bei der Anwendung von MSG-Schweißprozessen N2 - Lichtbogenbasierte Schweißverfahren wie das Metallschutzgasschweißen (MSG) zählen zu den Standardverfahren der Fügetechnik und werden in vielen Industriebereichen automatisiert unter Verwendung von Industrierobotern eingesetzt. Dabei können Schweißnahtabweichungen auftreten, die aus Änderungen der Prozessrandbedingungen und der hohen Prozessdynamik resultieren. Hier ist die Kontrolle von Schmelzbad- und Schweißnahtgeometrie für die Sicherung der Nahtqualität bedeutsam. Durch den Einsatz optischer Sensorsysteme können mit hoher zeitlicher Auflösung in-situ Informationen des Prozesszustands ermittelt werden. Dabei stellen die rauen Prozessbedingungen und die hohe Strahlungsintensität des Lichtbogens eine Herausforderung für die optischen Komponenten dar. Forschungsarbeiten am Institut für Schweißtechnik und Fügetechnik der RWTH Aachen haben gezeigt, dass durch den Einsatz einer HDR-Kamera in Kombination mit einer strukturierten Laserbelichtung gezielt geometrische Informationen des Lichtbogens und des Schmelzbads aus den Prozessaufnahmen gewonnen werden können. In dieser Arbeit wird eine parallele Schweißnaht- und Schmelzbadbeobachtung durchgeführt, wobei geometrische Informationen durch die Anwendung von Bildverarbeitungsalgorithmen extrahiert werden. Dabei wird ein nachlaufendes Sensorsystem eingesetzt, welches aus einer HDR-Kamera und einer Laserbeleuchtung besteht. Es werden diffraktive optische Elemente (DOE) zur Erzeugung von verschiedenen Laserprojektionsmustern verwendet, um sowohl eine unidirektionale als auch eine multidirektionale Prozessbeobachtung durchführen zu können. Aus den geometrischen Informationen werden Kenngrößen berechnet, anhand derer der Prozesszustand beurteilt werden kann. Es zeigt sich, dass anhand der Kenngrößenverläufe Abweichungen in der Schweiß- und Schmelzbadgeometrie und Positionierungsfehler des Roboters identifiziert werden können. T2 - Große Schweißtechnische Tagung - DVS CAMPUS CY - Online meeting DA - 14.09.2020 KW - Schweißnahtgeometrie KW - MSG-Schweißen KW - In-situ Monitoring KW - Schmelzbadbeobachtung PY - 2020 SN - 978-3-96144-098-6 VL - 365 SP - 41 EP - 47 PB - DVS Media GmbH CY - Düsseldorf AN - OPUS4-51576 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Oster, Simon T1 - In-situ Identifikation der Schweißnahtgeometrie bei der Anwendung von MSG-Schweißprozessen N2 - Lichtbogenbasierte Schweißverfahren wie das Metallschutzgasschweißen (MSG) zählen zu den Standardverfahren der Fügetechnik und werden in vielen Industriebereichen automatisiert unter Verwendung von Industrierobotern eingesetzt. Dabei können Schweißnahtabweichungen auftreten, die aus Änderungen der Prozessrandbedingungen und der hohen Prozessdynamik resultieren. Hier ist die Kontrolle von Schmelzbad- und Schweißnahtgeometrie für die Sicherung der Nahtqualität bedeutsam. Durch den Einsatz optischer Sensorsysteme können mit hoher zeitlicher Auflösung in-situ Informationen des Prozesszustands ermittelt werden. Dabei stellen die rauen Prozessbedingungen und die hohe Strahlungsintensität des Lichtbogens eine Herausforderung für die optischen Komponenten dar. Forschungsarbeiten am Institut für Schweißtechnik und Fügetechnik der RWTH Aachen haben gezeigt, dass durch den Einsatz einer HDR-Kamera in Kombination mit einer strukturierten Laserbelichtung gezielt geometrische Informationen des Lichtbogens und des Schmelzbads aus den Prozessaufnahmen gewonnen werden können. In dieser Arbeit wird eine parallele Schweißnaht- und Schmelzbadbeobachtung durchgeführt, wobei geometrische Informationen durch die Anwendung von Bildverarbeitungsalgorithmen extrahiert werden. Dabei wird ein nachlaufendes Sensorsystem eingesetzt, welches aus einer HDR-Kamera und einer Laserbeleuchtung besteht. Es werden diffraktive optische Elemente (DOE) zur Erzeugung von verschiedenen Laserprojektionsmustern verwendet, um sowohl eine unidirektionale als auch eine multidirektionale Prozessbeobachtung durchführen zu können. Aus den geometrischen Informationen werden Kenngrößen berechnet, anhand derer der Prozesszustand beurteilt werden kann. Es zeigt sich, dass anhand der Kenngrößenverläufe Abweichungen in der Schweiß- und Schmelzbadgeometrie und Positionierungsfehler des Roboters identifiziert werden können. T2 - Große Schweißtechnische Tagung - DVS CAMPUS CY - Online meeting DA - 14.09.2020 KW - Schweißnahtgeometrie KW - MSG-Schweißen KW - In-situ Monitoring KW - Schmelzbadbeobachtung PY - 2020 AN - OPUS4-51579 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Usmani, Shirin M. A1 - Plarre, Rüdiger A1 - Hübert, Thomas A1 - Kemnitz, E. ED - Richter, K. ED - Van de Kulien, J.-W. T1 - Termite resistance of pine wood treated with nano metal fluorides N2 - Fluorides are well-known as wood preservatives. One of the limitations of fluoride-based wood preservatives is their high leachability. Alternative to current fluoride salts such as NaF used in wood protection are low water-soluble fluorides. However, impregnation of low water-soluble fluorides into wood poses a challenge. To address this challenge, low water-soluble fluorides like calcium fluoride (CaF2) and magnesium fluoride (MgF2) were synthesized as nanoparticles via the fluorolytic sol−gel synthesis and then impregnated into wood specimens. In this study, the toxicity of nano metal fluorides was assessed by termite mortality, mass loss and visual analysis of treated specimens after eight weeks of exposure to termites, Coptotermes formosanus. Nano metal fluorides with sol concentrations of 0.5 M and higher were found to be effective against termites resulting in 100% termite mortality and significantly inhibited termite feeding. Among the formulations tested, the least damage was found for specimens treated with combinations of CaF2 and MgF2 with an average mass loss less than 1% and visual rating of “1”. These results demonstrate the efficacy of low water-soluble nano metal fluorides to protect wood from termite attack. KW - Holzschutzmittel KW - Nanoparticles KW - Fluorides KW - Termites PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-514325 DO - https://doi.org/10.1007/s00107-020-01522-z VL - 78 SP - 493 EP - 499 PB - Springer CY - Berlin AN - OPUS4-51432 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völker, Christoph T1 - Trends in Materials Informatics N2 - Many PhD students are interested in applying machine learning, AI, data science, etc., and there are many good reasons for this. However, there is a disconnect between mainstream data science and materials science, for example, when it comes to the sheer size of the data. This talk will highlight some of the unique challenges in materials informatics and present some interesting approaches to overcome them. Although the field is large, this talk will focus on cases that have some practical relevance to PhD students at BAM. T2 - PhD Day at BAM 2020 CY - Online meeting DA - 15.09.2020 KW - Materials Informatics KW - Small Data PY - 2020 AN - OPUS4-51814 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Waske, Anja T1 - Energy Harvesting Using Thermomagnetic Generators with Magnetocaloric Materials N2 - To date, there are only very few technologies available for the conversion of low temperature waste heat to electricity. More than a century ago, thermomagnetic generators were proposed, which are based on a change of magnetization with temperature, switching a magnetic flux, which according to Faraday’s law induces a voltage. In this talk, we first describe the principle of thermomagnetic generators. Then we focus on the impact of topology of the magnetic circuit within thermomagnetic generators. We demonstrate that the key operational parameters strongly depend on the genus, i.e. the number of holes within the magnetic circuit. A pretzel-like topology of the magnetic circuit with genus =3 improves the performance of thermomagnetic generators by orders of magnitude. We will show that this technique is on its way to becoming competitive with thermoelectrics for energy harvesting near room temperature. T2 - TMS Annual Meeting CY - San Diego, CA, USA DA - 23.02.2020 KW - Materials science KW - Energy harvesting PY - 2020 AN - OPUS4-51903 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Waske, Anja T1 - Materials for Thermomagnetic Harvesting of Low Temperature Waste Heat: N2 - Thermomagnetic materials are a new type of magnetic energy materials, which enable the conversion of low temperature waste heat to electricity by three routes: Thermomagnetic motors, generators and microsystems. Taking our recent work on thermomagnetic generators as a starting point, in this talk we analyse the material requirements for a more energy and economic efficient conversion. We will describe the influence of magnetisation change and heat capacity on thermodynamic efficiency, as well as the consequences of thermal conductivity on power density. Our analysis will allow selecting the best thermomagnetic materials in Ashby plots and illustrate the substantial different properties compared to magnetocaloric materials. Supported by DFG, project FA 453/14) T2 - TMS Annual Meeting CY - San Diego, CA, USA DA - 23.02.2020 KW - Materials science KW - Energy harvesting PY - 2020 AN - OPUS4-51904 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, David T1 - From W. C. Röntgen to modern Tomography N2 - A not complete review of X-Ray related milestones from 1895 to the 21st century. T2 - ITN GW4SHM, First Training Event CY - Online Meeting DA - 23.11.2020 KW - X-Ray KW - Computed Tomography KW - Laminography KW - Digital Detector Arrays KW - Wilhelm Conrad Röntgen PY - 2020 AN - OPUS4-51881 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Léonard, Fabien T1 - Overview of XCT data processing workflow for ammonium nitrate prills quantitative analysis N2 - This video presents the data processing workflow that was developed to perform the quantitative structural and morphological analysis of ammonium nitrate prills by x-ray computed tomography. KW - ANFO KW - Data processing KW - Explosives KW - Porosity KW - Surface area KW - XCT PY - 2020 DO - https://doi.org/10.5281/zenodo.3611339 PB - Zenodo CY - Geneva AN - OPUS4-51897 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Beckmann, Jörg T1 - Novel Technique for On-Line Monitoring of the Curing Process of Fiber Reinforced Polymer Composites N2 - A specially designed experimental set up has been integrated into a commercially available FT IR Spectrometer for ATR experiments on Epoxy Systems. Representative data of far infrared spectra measured during the curing process at different temperatures of an epoxy system will be presented in dependency of the curing situation. The experiments and the selected set up are discussed to demonstrate its potential for future monitoring and ageing control applications during a manufacturing process of polymer composites. T2 - 45. International Confercene on infrared, milimeter and terahertz waves CY - Online meeting DA - 08.11.2020 KW - Far-infrared spectroscopy KW - Curing Monitoring PY - 2020 UR - https://live-irmmwthz.pantheonsite.io/technical-program AN - OPUS4-51649 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kruschwitz, Sabine T1 - Evaluation of Advanced NDT-Methods for Measurement of Fibre Orientation in Concrete N2 - Integration of fibre reinforcement in high-performance cementitious materials has become widely applied in many fields of construction. One of the most investigated advantages of steel fibre reinforced concrete (FRC) is the deceleration of crack growth and hence it’s improved sustainability due to e.g. decrease of permeability of concrete by aggressive substances. Additional benefits are associated with the structural properties of FRC, where fibres can significantly increase the ductility and the tensile strength of concrete. In some applications, such as tunnel linings or industrial slabs, it is even possible to entirely replace the conventional reinforcement, leading to significant logistical and environmental benefits. Fibre reinforcement can, however, have critical disadvantages and even hinder the performance of concrete, since it can induce an anisotropic material behaviour of the mixture if the fibres are not appropriately oriented. For a safe use of FRC in the future, reliable non-destructive methods need to be identified to assess the fibres’ orientation in hardened concrete. In this study, ultrasonic material testing, electrical impedance testing, and X-ray computer tomography have been investigated for this purpose using specially produced samples with biased or random fibre orientations. This paper demonstrates the capabilities of each of these NDT techniques for fibre orientation measurements and draws conclusions based on these results about the most promising areas for future research and development using these techniques. T2 - fib2020 Shanghai CY - Online meeting DA - 22.11.2020 KW - Ultrasonic testing KW - Steel fibre reinforced concrete (FRC) KW - Fibre orientation KW - X-ray computed tomography (CT) KW - Electrical impedance PY - 2020 AN - OPUS4-51651 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bulling, Jannis A1 - Franosch, Georg A1 - Lugovtsova, Yevgeniya A1 - Prager, Jens ED - Rizzo, P. ED - Milazzo, A. T1 - Sensitivity of Ultrasonic Guided Waves to Elastic Constants: A Numerical Study N2 - The dispersive properties of Lamb waves can be utilised for material characterisation because the frequency-wavenumber-relationship, as well as the group velocity, depend on material parameters. These dependencies make a non-destructive estimation of an elastic constant possible. This preliminary study investigates the sensitivity of dispersion curves caused by a change in elastic constants. The Scaled Boundary Finite Element Method is used to compute special dispersion curves, which show the sensitivity value of the frequency and group velocity as a colour value. This representation allows for easy identification of patterns and local effects. Two sets of dispersion curves are presented, one set for a steel plate and the other set for a plate made of a carbon fibre reinforced polymer. In general, we notice that the sensitivity often increases with the frequency and that higher-order modes seem to be more suitable for material characterisation. Moreover, specific modes respond to material changes while others are relatively unaffected, which must be taken into consideration for material characterisation. T2 - European Workshop on Structural Health Monitoring (EWSHM 2020) CY - Online meeting DA - 06.07.2020 KW - Scaled Boundary Finite Element Method KW - Lamb waves KW - Dispersion curves KW - Carbon fibre reinforced polymer KW - Transverse isotropy PY - 2021 SN - 978-3-030-64593-9 DO - https://doi.org/10.1007/978-3-030-64594-6_73 VL - 127 SP - 759 EP - 768 PB - Springer CY - Cham AN - OPUS4-51986 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völker, Christoph T1 - Presenting “SLAMD” - The Sequential Learning App for Materials Discovery N2 - Environmentally friendly alternatives to cement are created through the synthesis of numerous base materials. The variation of their proportions alone leads to millions of materials candidates. Identifying suitable materials is very laborious; traditional systematic research in the laboratory consumes a lot of time and effort. Sequential learning (SL) potentially speeds up the materials research process despite limited but highly complex available information. SL does not make direct predictions of material properties but ranks possible experiments according to their utility. The most promising experiments are prioritized over dead-end experiments and experiments whose outcome is already known. Our work has shown that SL seems to be promising for cement research. So far, research has mainly focused on materials whose synthesis is faster and whose material properties require less time for development or characterization (allowing many successive experiments). Contrarily, in the case of binders, SL is only useful if few experiments lead to the desired goal, as for example, the determination of the compressive strength alone typically requires 28 days. In research practice, experimental designs and the availability of resources often determine which data can be used - for example, when some laboratory resources are not available or deemed irrelevant to a task. As a result, new research scenarios are constantly emerging, each of which requires to demonstrate SL’s performance. We are presenting the SLAMD app to facilitate the exploration of SL methods in numerous research scenarios. The app provides flexible and low-threshold access to AI methods via intuitive and interactive user interfaces. We deliberately pursue a software-based research approach (as opposed to code-, or script-based). On the one hand, the results are more comprehensible since we refer to a common (code) basis (’reproducible science’). On the other hand, the methods are easily accessible to all which accelerates the knowledge transfer into laboratory practice. T2 - DGM Materials Week 2021 CY - Online meeting DA - 07.09.2021 KW - Sequential learning KW - Scientific software KW - Alcali activated binders PY - 2021 AN - OPUS4-54128 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ehlers, Henrik T1 - Online ET with MR Sensor Arrays for LPBF Parts N2 - In this presentation we discuss the online monitoring of LPFB parts using eddy current testing with magenoresistive sensor arrays. The underlying principle, the developed hardware and the results of the firt online monitoring are described in the presentation. T2 - 2. Online-Workshop "In-situ Monitoring and Microstructure Development in Additive Manufactured Alloys " CY - Online meeting DA - 19.04.2021 KW - Eddy current testing KW - LPBF KW - GMR KW - SLM KW - Haynes282 KW - Additive manufacturing PY - 2021 AN - OPUS4-52700 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Portella, Pedro Dolabella A1 - Krebber, Katerina T1 - Fiber Optic Sensors for SHM - From Laboratory to Industrial N2 - The paper highlights the research activities in Germany and Europe in the development of distributed fiber optic sensor for structural health monitoring (SHM) like the monitoring of geotechnical and civil infrastructures and presents selected results achieved within these projects. T2 - Conaendi & IEV 2021 CY - Online meeting DA - 09.03.2021 KW - Fiber KW - Optic KW - SHM PY - 2021 AN - OPUS4-52254 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baensch, Franziska T1 - Acoustic emission of fibre reinforced AlSi12CuMgNi alloy under compression N2 - Typically, the near-eutectic Al-Si alloys consist of highly interconnected three-dimensional network of the eutectic Silicon (Si) and intermetallics embedded into Aluminium (Al) matrix. For further improvement of the mechanical properties of such alloys, often, one single ceramic reinforcement phase, e.g. silicon carbide (SiC) or aluminium oxide (Al2O3) in the form of fibres or particles is added. However, hybrid reinforcements (fibres and particles) can further improve wear resistance and fracture toughness, and additionally, reduce anisotropy of the material. The engineering of metal matrix composites (MMC) for specific application requirements benefits from a comprehensive knowledge of the failure behaviour. Therefore, damage evolution under compression was investigated on: - pure near-eutectic AlSi12CuMgNi matrix alloy - type I: matrix reinforced with random-planar oriented Al2O3 short fibres (15 vol.%) - type II: matrix reinforced with random-planar oriented Al2O3 short fibres (7 vol.%) and additional SiC particles (15 vol.%) The analysis of damage mechanism was carried out in two rather independent but complementary studies. First, selected sister samples of every material were exposed to quasi-static compression (traverse control). The compression tests were interrupted at different strain levels. Miniature cylinders with a diameter of 1mm were extracted from the pre-strained samples and investigated by synchrotron computed tomography (SX-µCT) with a spatial resolution of about 0.7 µm. For the pure matrix alloy, microcracks are confined to the intermetallic particles and to the eutectic Si, hence no damage was observed in the Aluminium. The composite type II revealed a more effective strain accumulation (less damage) than type I at low plastic strain (up to 5 %), but a more catastrophic damage development due to cracking of the SiC clusters at higher strain levels. The second approach to study the damage initiation and accumulation in the materials subjected to compressive load was Acoustic Emission (AE) analysis. In this case the in-situ monitoring of the acoustic emission signal was performed during compression tests on specimens with dimension of several mm. For all three material types, AE activity set at 2% strain. Differences in AE behaviour of the three materials was proven based on AE hitrate, signal peak amplitudes as well as weighted peak frequencies (WPF). Future work focuses on combination of AE and SX-µCT aiming for more detailed knowledge on damage mechanism of metal matrix composites. T2 - Schall21 CY - Online meeting DA - 24.02.2021 KW - AlSi12CuMgNi KW - Al-Si alloys KW - Acoustic emission KW - Tension PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-534268 UR - https://www.dgzfp.de/seminar/schall21 AN - OPUS4-53426 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baensch, Franziska T1 - Der Verformungswiderstand im Holz und die Rolle der Holzstrahlen N2 - Von den Zellulosefibrillen über die Zellwand und die Anordnung der Früh- und Spätholzzellen in einem Jahrring bis hin zum Balken von Natur aus ist Holz ein optimierter Hochleistungswerkstoff, der Handwerker, Architekten, Ingenieure und Wissenschaftler fasziniert und begeistert. Im digitalen Zeitalter werden neben Standard-Laborexperimenten zunehmend Modelle und Simulationen eingesetzt, um das Verhalten des Materials unter verschiedenen Belastungen besser zu verstehen und vorherzusagen. Dazu werden Zahlenwerte von Verformungen im subzellulären Maßstab benötigt, die nun in Experimenten an der TOMCAT-Beamline (TOmographic Microscopy and Coherent rAdiology ExperimenTs) der SLS (Swiss Light Source) gewonnen werden konnten: Holzproben aus Fichte ( Picea abies Karst.) mit einem Prüfquerschnitt von mindestens 1 mm² auf Zug oder Druck beansprucht. Die strukturellen Veränderungen auf Zellebene wurden mittels Computertomographie erfasst. Für die nachträgliche Analyse der 3D-Mikrostruktur von Holz wurde ein Ansatz entwickelt, der es ermöglicht, einzelne Zellen, die in mehreren Tomogrammen unterschiedlicher Belastungszustände erfasst wurden, zu verfolgen. Dabei wurden die Zellgeometrien und das subzelluläre Deformationsverhalten quantifiziert. Unter Zugbelastung beispielsweise verengt sich die Zellwanddicke um ca. 0,8%, das sind bei der gemessenen mittleren Zellwanddicke von 3,5 µm ca. 28 nm. Diese und andere Erkenntnisse liefern nun einen direkten numerischen Zusammenhang zwischen Verformungen der Holzmikrostruktur und dem daraus resultierenden makroskopischen Verhalten. T2 - 5. Holzanatomisches Kolloquium CY - Dresden, Germany DA - 09.09.2021 KW - Holz KW - Wood materials KW - Individual cell tracking KW - Mikro CT PY - 2021 AN - OPUS4-53403 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baensch, Franziska A1 - Sanabria, S. T1 - Der Verformungswiderstand im Holz und die Rolle der Holzstrahlen N2 - Von den Zellulosefibrillen über die Zellwand und die Anordnung der Früh- und Spätholzzellen in einem Jahrring bis hin zum Balken von Natur aus ist Holz ein optimierter Hochleistungswerkstoff, der Handwerker, Architekten, Ingenieure und Wissenschaftler fasziniert und begeistert. Im digitalen Zeitalter werden neben Standard-Laborexperimenten zunehmend Modelle und Simulationen eingesetzt, um das Verhalten des Materials unter verschiedenen Belastungen besser zu verstehen und vorherzusagen. Dazu werden Zahlenwerte von Verformungen im subzellulären Maßstab benötigt, die nun in Experimenten an der TOMCAT-Beamline (TOmographic Microscopy and Coherent rAdiology ExperimenTs) der SLS (Swiss Light Source) gewonnen werden konnten: Holzproben aus Fichte ( Picea abies Karst.) mit einem Prüfquerschnitt von mindestens 1 mm² auf Zug oder Druck beansprucht. Die strukturellen Veränderungen auf Zellebene wurden mittels Computertomographie erfasst. Für die nachträgliche Analyse der 3D-Mikrostruktur von Holz wurde ein Ansatz entwickelt, der es ermöglicht, einzelne Zellen, die in mehreren Tomogrammen unterschiedlicher Belastungszustände erfasst wurden, zu verfolgen. Dabei wurden die Zellgeometrien und das subzelluläre Deformationsverhalten quantifiziert. Unter Zugbelastung beispielsweise verengt sich die Zellwanddicke um ca. 0,8%, das sind bei der gemessenen mittleren Zellwanddicke von 3,5 µm ca. 28 nm. Diese und andere Erkenntnisse liefern nun einen direkten numerischen Zusammenhang zwischen Verformungen der Holzmikrostruktur und dem daraus resultierenden makroskopischen Verhalten. T2 - 5. Holzanatomisches Kolloquium CY - Dresden, Germany DA - 09.09.2021 KW - Wood materials KW - Holz KW - Individual cell tracking KW - Mikro CT PY - 2021 SP - 92 EP - 101 CY - Dresden AN - OPUS4-53405 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mishurova, Tatiana T1 - 3D imaging and residual stress analysis of AM materials at BAM N2 - The overview of the activity of group 8.5 Micro-NDT (BAM, Belin, Germany) in the field of additively manufacturing material characterization will be presented. The research of our group is focused on the 3D imaging of AM materials by means of X-ray Computed Tomography at the lab and at synchrotron, and the residual stress characterization by diffraction (nondestructive technique). T2 - Seminar at Chalmers University and Centre for Additive Manufacture (CAM2) CY - Gothenburg, Sweden DA - 19.05.2022 KW - Additive manufacturing KW - Laser powder bed fusion KW - Residual stress KW - Computed tomography KW - Synchrotron X-ray diffraction KW - X-ray refraction PY - 2022 AN - OPUS4-55019 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Roveda, Ilaria T1 - Investigation of residual stresses and microstructure effects on the fatigue behaviour of a L-PBF AlSi10Mg alloy N2 - Laser Powder Bed Fusion (L-PBF) allow the fabrication of lightweight near net shape AlSi10Mg components attractive to the aerospace, automotive, biomedical and military industries. During the build-up process, high cooling rates occur. Thus, L-PBF AlSi10Mg alloys exhibit a Si-nanostructure in the as-built condition, which leads to superior mechanical properties compared to conventional cast materials. At the same time, such high thermal gradients generally involve a deleterious residual stress (RS) state that needs to be assessed during the design process, before placing a component in service. To this purpose post-process heat treatments are commonly performed to relieve detrimental RS. In this contribution two low-temperature stress-relief heat treatments (SRHT) are studied and compared with the as-built state: a SRHT at 265°C for 1 hour and a SRHT at 300°C for 2 hours. At these temperatures microstructural changes occur. In the as-built state, Si atoms are supersaturated in the α-aluminium matrix, which is enveloped by a eutectic Si-network. At 265°C the Si precipitation from the matrix to the pre-existing network is triggered. Thereafter, above 295°C the fragmentation and spheroidization of the Si branches takes place, presumably by Al–Si interdiffusion. After 2 hours the original eutectic network is completely replaced by uniformly distributed blocky particles. The effect of the heat and the microstructure modification on the RS state and the fatigue properties is investigated. Energy dispersive x-ray and neutron diffraction are combined to investigate the near-surface and bulk RS state of a L-PBF AlSi10Mg material. Differences in the endurance limit are evaluated experimentally by high cycle fatigue (HCF) tests and cyclic R-curve determination. T2 - 43rd Materials Mechanics Seminar CY - Sani, Chalkidiki, Greece DA - 05.06.2022 KW - AlSi10Mg KW - Fatigue KW - Neutron diffraction KW - X-ray diffraction PY - 2022 AN - OPUS4-55090 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baensch, Franziska T1 - Charakterisierung von Salzbeton und alkali-aktivierten Material basierend auf der Schallemissionsanalyse N2 - Nach einer kurzen Einführung in die Schallemissionsprüfung und -Analyse wird ein Versuchsstand vorgestellt, der im Rahmen des Themenfeldprojektes Seal Waste Safe installiert wurde. Schwerpunkt des Vortrages sind die Schallemissionsmessungen an einem 150 l Demonstrator aus Salzbeton und einem weiteren aus alkali-aktiviertem Material. Neben der konventionellen Schallemissionsanaylse mit Aktivitäts- und Intensitätsparametern der Zeitsignale, werden auch frequenzbasierte Parameter zur Analyse andiskutiert. N2 - After a brief introduction to acoustic emission testing and analysis, an experimental test setup is presented, which was part of the Seal Waste Safe project (internal BAM project 2019-2022). Herein, the acoustic emission measurements of a 150 l demonstrator made of salt concrete and another one made of alkali-activated material are focused. In addition to the conventional acoustic emission analysis regarding the activity and intensity parameters of the detected time signals, also frequency-based parameters were discussed for analysis. T2 - Dauerhafte Verschlussbauwerke für Endlager CY - Online meeting DA - 14.2.2022 KW - Acoustic Emission KW - Schallemission KW - Salzbeton KW - Alkali aktiviertes Material KW - Geopolymer PY - 2022 AN - OPUS4-54937 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -