TY - THES A1 - Zoëga, Andreas T1 - Spannungsabhängigkeit elastischer Wellen in Beton N2 - Beton, einer der vielseitigsten und meist-verbreitetsten Baustoffe, verdankt diese Popularität seiner hohen Druckfestigkeit bei gleichzeitig geringen Kosten auf der einen Seite sowie seiner hohen Flexibilität durch die Möglichkeit der fast beliebigen Formgebung von lastabtragenden Elementen und Bauteilen auf der anderen Seite. Die weltweit verbreiteten Betonbauwerke altern und drängen die zerstörungsfreie Prüfung dazu, Prüfmethoden für eine effektive Zustandsbewertung von im Betrieb befindlichen Betonbauwerken zur Verfügung zu stellen. Für viele in anderen zerstörungsfreien Prüfbereichen alltägliche Anwendungen stellt Beton aufgrund der Heterogenität des Verbundwerkstoffs mit seinem nichtlinearen Spannungs-Dehnungs-Verhalten eine Herausforderung dar. Mit steigender Spannung nehmen die nichtlinearen Eigenschaften noch zu und können - z. B. durch die sich in Abhängigkeit von der Belastungsrichtung bildenden Mikrorisse - zu einer anisotropen Ausbildung von Eigenschaften führen, welche u. a. mit elastischen Wellen in Wechselwirkung treten. Bisherige Prüfaufgaben an Beton beschränken sich auf Bereiche, bei denen die elastischen Wellen ein lineares Verhalten aufweisen und sind daher nicht uneingeschränkt anwendbar. Gerade der Zusammenhang von Spannungszustand und Anisotropie zeigt eindeutige nichtlineare Effekte auf die Eigenschaften elastischer Wellen. Diese Eigenschaftsänderungen von elastischen Wellen sollen in dieser Arbeit anhand der Schallgeschwindigkeit erörtert werden. Neben einer Beobachtung und Dokumentation der auftretenden Effekte werden die Ursachen und Wirkmechanismen, die zu einer Schallgeschwindigkeitsänderung unter einer Druckbelastung führen, untersucht. In einem Vorversuch wurden Wellen unterschiedlichen Typs, Frequenz, Polarisation und Ausbreitungsrichtung auf ihre Sensitivität gegenüber einer Belastung miteinander verglichen. Hierbei stellte sich die Oberflächenwelle als die belastungsempfindlichste heraus und wird in dieser Arbeit für die Beschreibung der spannungsabhängigen Eigenschaftsänderungen von elastischen Wellen bevorzugt verwendet. Die für diese Versuchsserie erstellten Versuchsaufbauten und die verwendeten Oberflächenwellen erlaubten eine beliebige Orientierung der Messrichtung in Bezug zur Lastrichtung. Die Änderung der Schallgeschwindigkeit konnte damit in Richtungsabhängigkeit verfolgt und anisotropes Verhalten beobachtet werden. Ultraschallwellen sind für Untersuchungen an Beton die am häufigsten verwendeten; infolgedessen wurde zum Vergleich parallel mit Ultraschallwellen unterschiedlicher Frequenzen gemessen. Als Ergebnis aus der Versuchsserie konnte der Auslastungs- und Schädigungsgrad des Betons nachvollzogen und damit die Änderung der Schallgeschwindigkeit in Abhängigkeit von der aufgebrachten Last für eine sichere Bruchvorhersage verwendet werden. Mit wachsender Belastung stieg dabei die Schallgeschwindigkeit an, dieser Anstieg verlangsamte sich und ging im Bereich zwischen 50-80 % der Bruchlast in eine zunehmende Schallgeschwindigkeitsreduktion über. Der größte Schallgeschwindigkeitszuwachs konnte zu Beginn in Lastrichtung beobachtet werden, während die größte Schallgeschwindigkeitsreduktion in orthogonaler Richtung kurz vor dem Bruch stattfand. Der bei geringer Belastung (linear-elastischer Bereich) besonders deutliche Schallgeschwindigkeitsanstieg kann mithilfe der Akustoelastizität erklärt werden. Der sich vermindernde Anstieg und die Schallgeschwindigkeitsreduktion ließen sich experimentell auf die Mikrorissentstehung und das Mikrorisswachstum innerhalb des Betons zurückführen. Des Weiteren konnte gezeigt werden, dass sich die Schallgeschwindigkeit bei einer Wiederbelastung von der bei einer Erstbelastung unterscheidet, dieser Unterschied sich bei einer höheren Vorbelastung vergrößert, die Anzahl der vorangegangenen Belastungen einen Einfluss hat und eine Überlastung sich besonders deutlich in einer Schallgeschwindigkeitsminderung niederschlägt. Bei den Schallgeschwindigkeitsänderungen konnte ebenso eine zeitabhängige Komponente beobachtet werden. Die typischen Kurvenverläufe der Schallgeschwindigkeit über der Spannung konnten ebenso an Probekörpern mit anderen Betonrezepturen sowie an bewehrten Probekörpern aufgezeichnet werden. Die spannungsabhängige Änderung der Geschwindigkeit von elastischen Wellen in Beton ist ein nicht zu vernachlässigender Effekt, welcher für Prüfverfahren zur Inspektion von bestehenden Gebäuden in Betracht gezogen werden kann. Ein Verständnis für die Ursachen der belastungs- bzw. zerstörungsgradabhängigen Geschwindigkeitsänderung der elastischen Wellen in Beton ebnet den Weg zur Entwicklung und Etablierung neuer Prüfmethoden, mit deren Hilfe vor Ort und zerstörungsfrei der Auslastungs- und Schädigungsgrad einer Betonstruktur bestimmt werden kann. N2 - Concrete is one of the most widely used construction materials. Concrete owes this popularity to its high compressive strength, low costs and the flexibility of being cast in the form of customized structural elements and load-bearing members. The many concrete structures around the world are aging, urging the NDT community to develop testing tools for effective inspection of in-service concrete structures. Concrete poses a challenge to the application of standard NDT techniques. Concrete is a multi-phase heterogeneous material with a nonlinear stress-strain behavior. Loading and the resulting damage (i.e., microcracking) increase the non-linearity and may induce anisotropy in concrete. As a result, many of the common wave propagation-based NDT methods relying on linear elastic theory are no longer applicable. The main objective of this study is to investigate the stress-induced changes in the velocity of elastic waves in concrete under uniaxial compression. The underlying mechanisms of the observed effects have been also investigated here. A preliminary experiment was conducted to study the influence of the type, frequency, polarization, and propagation direction of elastic waves on the stress-induced velocity changes. The velocity of sonic surface waves (Rayleigh waves) demonstrated the highest sensitivity and therefore, much of this work is focused on the stress-induced changes in surface wave propagation characteristics. The test setup allowed measuring the surface wave velocities along various directions with respect to the loading direction and therefore, the direction-dependency of the surface wave velocity measurements was also investigated. Standard ultrasonic testing of various frequencies was also conducted and the results were compared to those from sonic surface wave measurements. Sonic surface wave velocities were found to be highly stress- and damage-dependent. Application of stress results in an initial sharp increase in surface wave velocity. Increasing the stress, the wave velocities continue to increase, however, the rate of increase decreases for stress levels between 50% and 80% of the failure stress, after which the velocities start rapidly to decrease. The sharpest increase was recorded in the direction of the loading, while the velocities decreased the fastest in the perpendicular direction. The sharp initial increase in wave velocities (within the elastic region) can be explained by acoustoelastic effects. The initiation and development of microcracks within concrete result in the observed velocitystress relationship beyond the elastic region. The test specimens were generally loaded in several load cycles and wave velocities were measured during both loading and unloading phases. It was found that the load history has a major effect on the velocity measurements. For previously loaded specimens, a notable difference between the velocity measurements during unloading and reloading was recorded. The higher the maximum previous load, the larger was the difference. Also, overloading the specimens resulted in a very large loss in surface wave velocities. Similar qualitative velocitystress relationships were obtained for a number of different concrete mixes as well as the reinforced concrete. Stress-dependency of elastic wave velocities in concrete is an important effect, which needs to be taken into account for in-situ measurements of in-service structural elements. Understanding and establishing the stress- and –damage dependency of wave velocities in concrete paves the way for developing new NDT techniques, which can be used to nondestructively estimate the in-situ stress and damage state of concrete. T3 - BAM Dissertationsreihe - 76 KW - Beton KW - Mikrorisse KW - Oberflächenwellen KW - Schallgeschwindigkeit KW - Spannungsabhängigkeit KW - Akustoelastizität KW - Richtungsabhängigkeit KW - elastische Wellen KW - Belastung PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-820 SN - 978-3-9814281-6-2 SN - 1613-4249 VL - 76 SP - 1 EP - 175 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-82 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Basan, Ricardo T1 - Untersuchung der intralaminaren Schubeigenschaften von Faserverbundwerkstoffen mit Epoxidharzmatrix unter Berücksichtigung nichtlinearer Effekte N2 - Faserverbundwerkstoffe besitzen anisotrope Materialeigenschaften. Die Anzahl der elastischen Größen und Festigkeiten zur Beschreibung des mechanischen Verhaltens ist dadurch größer als zum Beispiel bei isotropen Werkstoffen. Die Festigkeiten und die Steifigkeiten in den verschiedenen Laminatrichtungen unterscheiden sich darüber hinaus um bis zu zwei Größenordnungen. Abhängig von der Belastungsart versagen Faserverbundwerkstoffe spröde oder duktil. Der Entwicklung geeigneter Untersuchungsmethoden zur Bestimmung der Werkstoffeigenschaften in den verschiedenen Richtungen kommt daher eine grundlegende Rolle zu. Insbesondere die Bestimmung der intralaminaren Schubeigenschaften von Faserverbundwerkstoffen ist aufgrund des ausgeprägten nichtlinearen Last-Verformungs-Verhaltens schwierig und mit den bestehenden Auswerteroutinen genormter Prüfverfahren teilweise fehlerbehaftet. Im Rahmen dieser Arbeit erfolgt die Analyse der Schubeigenschaften in der Laminatebene durch eine neu entwickelte Schubvorrichtung, die eine qualitativ hochwertige Bestimmung der Werkstoffeigenschaften ermöglicht. Für die Probekörper dieser Schubvorrichtung wird auf der Grundlage von Messergebnissen ein lastabhängiges Modell der Schubspannungsverteilung entwickelt, das die Materialnichtlinearität berücksichtigt und bei der Analyse der Versuchsergebnisse zur Anwendung kommt. In vergleichenden Untersuchungen der Interaktion benachbarter Schichten an glas- und kohlenstofffaserverstärkten Laminaten mit ein- und zweiachsiger Orientierung kann gezeigt werden, dass bei identischem Schubspannungszustand in den Einzelschichten bis zu 60% größere Schubfestigkeiten der zweiachsig verstärkten Verbunde vorliegen. Die orthogonal verstärkten Laminate sind schadenstoleranter, da sich Zwischenfaserbruche nicht ungehindert ausbreiten können, sondern an den um 90° gedrehten Fasern gestoppt werden. In Laminaten mit unidirektionaler Faserausrichtung führt dagegen der erste Riss unmittelbar zum Trennbruch. Die Verifizierung dieser Beobachtung erfolgt mittels des Verfahrens der Röntgenrefraktions- topographie. In Schubzugversuchen erfolgt die Korrelation der mechanischen Belastungssituation mit der mikrostrukturellen Analyse der inneren Schädigungsentwicklung des Werkstoffs. An zweiachsig verstärkten Kohlenstofffaserlaminaten unter Zwischenfaserbruchbeanspruchung kann gezeigt werden, dass die Degradation der intralaminaren Schubsteifigkeit mit der Zunahme an inneren Oberflachen als Maß für die Zwischenfaserbruchdichte einhergeht. Einachsig verstärkte Verbunde versagen dagegen relativ spröde bereits durch den ersten Zwischenfaserbruch und damit ohne Zunahme der Mikrorissdichte. Die Zusammenfassung der Erkenntnisse spiegelt sich in der Verbesserung des Auswerteverfahrens des in DIN EN ISO 14129 genormten Schubzugversuchs wider. Unter Berücksichtigung der Nichtlinearitat des Schubmoduls und der Faserrotation infolge der großen Verformungen während des Schubzugversuchs erfolgt in einem Iterationsprozess die stuckweise Anwendung der Klassischen Laminattheorie zur Bestimmung der Einzelschichtspannungen. Die Bewertung der Ergebnisse des Schubzugversuchs mit diesem Analyseverfahren hinsichtlich der Belastungsgrenzen resultiert in einer guten Übereinstimmung mit dem Festigkeitsmodell nach Puck. Die Berücksichtigung nichtlinearer Effekte führt zu einer höheren Genauigkeit bei der Bestimmung der intralaminaren Schubfestigkeit mittels des in der industriellen Anwendung weit verbreiteten Normversuchs. T3 - BAM Dissertationsreihe - 74 KW - Zwischenfaserbruch KW - interfibre failure KW - nonlinearity KW - test methods KW - in-plane shear KW - composite materials KW - Faserverbundwerkstoffe KW - intrlaminare Schubeigenschaften KW - Prüfverfahren KW - Nichtlinearität PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-848 SN - 978-3-9814281-3-1 SN - 1613-4249 VL - 74 SP - 1 EP - 170 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-84 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR T1 - Amts- und Mitteilungsblatt, Band 41, Heft 4 T2 - Amts- und Mitteilungsblatt T3 - Amts- und Mitteilungsblatt der BAM - 4/2011 PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-134 SN - 0340-7551 VL - 41 IS - 4 SP - 1 EP - 125 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-13 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR T1 - Amts- und Mitteilungsblatt, Band 41, Heft 3 T2 - Amts- und Mitteilungsblatt T3 - Amts- und Mitteilungsblatt der BAM - 3/2011 PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-143 SN - 0340-7551 VL - 41 IS - 3 SP - 1 EP - 43 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-14 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR T1 - Amts- und Mitteilungsblatt, Band 41, Heft 2 T2 - Amts- und Mitteilungsblatt T3 - Amts- und Mitteilungsblatt der BAM - 2/2011 PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-159 SN - 0340-7551 VL - 41 IS - 2 SP - 1 EP - 111 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-15 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR T1 - Amts- und Mitteilungsblatt, Band 41, Heft 1 T2 - Amts- und Mitteilungsblatt T3 - Amts- und Mitteilungsblatt der BAM - 1/2011 PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-162 SN - 0340-7551 VL - 41 IS - 1 SP - 1 EP - 187 PB - Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-16 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mishra, Kirti Bhushan A1 - Wehrstedt, Klaus-Dieter T1 - An efficient and clean fuel for high temperature process industries T2 - 11th Conference on energy for a clean environment N2 - The use of energetic materials as a main fuel in high temperature process industries are not known to the scientific community as such. This paper highlights some of the features and advantages of using organic peroxides especially di-tert-butyl peroxide (DTBP) in high temperature process industries. The feasibility of using DTBP as a main or supporting fuel in process industries have also been justified with the help of Computational Fluid Dynamics (CFD) simulations. For peroxides requirement of less fuel and air for the same amount of heat flux has been shown. The resulted emission from the combustion of DTBP is also discussed. T2 - 11th Conference on Energy for a Clean Environment CY - Lisbon, Portugal DA - 2011-07-05 KW - Energetic materials KW - Process industries KW - Organic peroxide KW - Di-tert-butylperoxide (DTBP) KW - CFD simulation KW - Emission PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-247071 SP - 1 EP - 10 AN - OPUS4-24707 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jakubcová, Petra A1 - Rübner, Katrin A1 - Schnell, A. T1 - Leichtgranulate aus heterogenem Bauschutt zur Herstellung von Beton T2 - r2- Statusseminar 2011, "Innovative Technologien für Ressourceneffizienz - rohstoffintensive Produktionsprozesse, Fraunhofer-Institut N2 - Untersucht wird die Entwicklung einer Technologie zur Herstellung hochwertiger Leichtgranulate (Blähgranulate) mit definierten Produkteigenschaften aus heterogenen Bau- und Abbruchabfällen, Anwendung der Granulate als leichte Gesteinskörnung im Beton und die Möglichkeit des rohstofflichen Recyclings mineralischer Bauabfälle T2 - r2- Statusseminar 2011, "Innovative Technologien für Ressourceneffizienz - rohstoffintensive Produktionsprozesse, Fraunhofer-Institut CY - Berlin, Germany DA - 26.10.2011 PY - 2011 AN - OPUS4-24717 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Wolfram A1 - Priebe, Nsesheye Susan A1 - Kühne, Hans-Carsten T1 - SPIN- Spearhead network for innovative,clean and safe cement & concrete technologies T2 - Workshop Cement and Concrete for Africa N2 - Worldwide, cement and concrete experts are at the cutting-edge to sustainable, green, healthy but nonetheless high-Performance concrete. The current relatively low development of the cement and concrete industry in Africa offers the unique opportunity to start directly on the best achievable and sustainable Level, if only Expertise is sufficiently available. It should not be neglected that concrete is a product with comparably low Transport ranges, which means that an improved concrete market will mainly Support the local economy without exceeding financial Drains to the international market, thus fostering the fight against poverty, which is an urgent Need in most African countries. T2 - Workshop Cement and Concrete for Africa CY - Berlin, Germany DA - 17.08.2011 PY - 2011 N1 - Geburtsname von Priebe, Nsesheye Susan: Msinjili, N. S. - Birth name of Priebe, Nsesheye Susan: Msinjili, N. S. AN - OPUS4-24728 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Antoni, S. A1 - Kunath, K. A1 - Lüth, Peter A1 - Simon, K. A1 - Uhlig, S. T1 - Evaluation of the interlaboratory test on the method UN O.2 / EC A.21 'Test for oxidizing liquids' 2009 - 2010 N2 - For the classification of chemicals, special standardized test procedures have been developed and are used world-wide. Safe handling and use of these chemicals depend on the correct classification which therefore must be based on the precise and correct execution of the tests and their evaluation. In this context interlaboratory tests (round robin tests, interlaboratory comparisons / intercomparisons) are a crucial element of a laboratory's quality system. Participation in interlaboratory tests is explicitly recommended by the standard ISO/IEC 17025. The present document reports on the results of the interlaboratory test 2009/2010 on the test methods UN O.2 “Test for oxidizing liquids” [1] / EC A.21 “Oxidizing Properties (Liquids)” [2] which was organized by the Center for Quality Assurance for Testing of Dangerous Goods and Hazardous Substances. The test methods UN O.2 and EC A.21 are applied to characterize the oxidizing properties of liquid chemical substances or mixtures. To differentiate between chemicals with hazardous / dangerous oxidizing properties and chemicals which are not classified as hazardous / dangerous, the substance’s oxidizing properties are compared to those of a standard reference substance. Since the methods (UN O.2 / EC A.21) were developed and came into force in the early nineties a systematic review concerning the practical application of the test method has not been carried out. KW - Oxidiser KW - Oxidierend KW - Gefahrgut KW - Dangerous goods KW - UN O.2 KW - Prüfmethode KW - Test method PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-250904 SN - 978-3-9814634-0-8 SP - 1 EP - 95 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin ET - Final report AN - OPUS4-25090 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Osterhus, Lennart A1 - Rübner, Katrin T1 - Kieselsäurehaltiger Filterrückstand aus industrieller Abwasserbehandlung für den Einsatz als hydraulisches Bindemittel T2 - GDCh-Tagung Bauchemie N2 - - 5.000 bis 10.000 t wasserhaltiger Filterrückstand (FR) entstehen jährlich pro Produzent bei der Neutralisation der Abwässer aus der Silicon- oder Kieselsäureherstellung - Anfall als fester, feuchter, schollenartiger Filterkuchen - Verwertung heute: Deponierung, Tagebauverfüllung -> ungenutzte Sekundärrohstoffquelle - Untersuchung der Einsatzmöglichkeiten der aufbereiteten Filterrückstände zur Eigenschaftsverbesserung zementgebundener Baustoffe analog der wohlbekannten Anwendung von hochdisperser Kieselsäure und Silicastaub T2 - GDCh-Tagung Bauchemie CY - Hamburg, Germany DA - 06.10.2011 PY - 2011 AN - OPUS4-24819 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Antoni, S. A1 - Clemens, J. A1 - Kunath, K. A1 - Rabe, J. A1 - Simon, K. A1 - Uhlig, S. A1 - Wehrstedt, Klaus-Dieter T1 - Evaluation of the 3rd round robin on solid oxidizer test (UN O.1) with calcium peroxide, sodium nitrate, sodium perborate monohydrate N2 - The classification of solid oxidizers according to the regulations on the transport of dangerous goods (based on the UN Recommendations/Model Regulations and accepted by all international organisations for the transport of dangerous goods as ADR, IMO, IATA) and in future also according to the GHS (Globally Harmonized System of Classification and Labelling of Chemicals) is performed on the basis of the results of the UN test O.1 (UN test O.1 ―Test for oxidizing solids‖ described in chapter 34.4.1 in the Recommendations on the Transport of Dangerous Goods – Manual of Tests and Criteria, see [1]). This test was introduced into the UN Manual of Tests and Criteria in 1995 as a replacement for a similar test from 1986. Even if the UN O.1 test as described in the current 5th revised edition of UN Manual of Tests and Criteria gives some improvements compared to the old test, which had had many deficiencies, there are still some problems left with this test in terms of e.g. repeatability or reproducibility of test results, how to handle compacted or multilayer formulations like tablets, toxicity and partly significantly varying particle size distribution within defined fractions of 150 μm to 300 μm of the reference oxidizer potassium bromate (KBrO3). For this reason the IGUS EOS working group installed an ad-hoc working group in 2002 assigned with the task to propose solutions for the existing problems. The appropriateness of such proposed solutions has to be proved by the method of interlaboratory (round robin) tests before they are presented for the adoption to the UN Committee of Experts on the TDG and on the GHS with a proposal of a completely revised test procedure. KW - Round robin KW - Solid oxidizer test KW - United Nations KW - IGUS KW - EOS KW - Calcium peroxide KW - Sodium nitrate KW - Sodium perborate monohydrate PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-232246 SN - 978-3-9813853-7-3 IS - Final Report, 2009 - 2011 SP - 1 EP - 192 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-23224 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dörfel, Ilona A1 - Rooch, Heidemarie A1 - Österle, Werner A1 - Kranzmann, Axel T1 - Vanadium and chromium containing precipitates in heat resistant steel T92 T2 - "Current Developments in TEM" (JEOL user meeting) T2 - "Current Developments in TEM" (JEOL user meeting) CY - Freiberg, Germany DA - 10.03.2011 PY - 2011 AN - OPUS4-22678 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, Wolfgang A1 - Heidmann, G. T1 - Monitoring von Hochspannungskabel-Muffen und -Endverschlüssen T2 - Expertenforum Strukturmonitoring auf der Sensor+Test-Messe N2 - - Zunehmender Energiebedarf erfordert höhere Übertragungskapazitäten - Dezentrale ökologische Energiegewinnung, z. B. Offshore, erfordert Übertragung großer Energiemengen in die Ballungszentren (Nord-Süd-Trassen) - Hohe Auslastung der Netze erfordert Beherrschbarkeit der im Fehlerfall auftretenden Risiken für Menschen, Umwelt und energietechnische Anlagen - Etwa 90 % der Anlagenausfälle sind verursacht durch Teilentladungen (TE) in Endverschlüssen und Muffen mit modernen polymeren Isoliersystemen - Etablierte elektrische Verfahren erlauben nur externe Schadensdetektion. T2 - Expertenforum Strukturmonitoring auf der Sensor+Test-Messe CY - Nuremberg, Germany DA - 08.06.2011 PY - 2011 AN - OPUS4-24054 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ried, Peter A1 - Gaber, Martin A1 - Müller, Ralf A1 - Holtappels, Kai A1 - Schmidtchen, Ulrich A1 - Deubener, J. T1 - Wasserstoffpermeations-messung an Gläsern T2 - Glastechn. Tagung, HVG-DGG T2 - Glastechn. Tagung, HVG-DGG CY - Saarbrücken, Germany DA - 30.05.2011 PY - 2011 AN - OPUS4-24012 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, Wolfgang A1 - Basedau, Frank T1 - Langzeitmonitoring der Ederstaumauer T2 - Expertenforum Strukturmonitoring auf der Sensor+Test-Messe N2 - Die Fixierung der Stahlanker im Felsfundament zur Stabilisierung der Schwergewichtsmauer werden mit integrierten faseroptischen Dehnungssensoren überwacht. In die Glasfaser sind Reflektoren eingebaut; zwei Reflektoren bilden jeweils eine Messstrecke, die Auskunft über die Fixierung geben. Am Ankerkopf wird der Zustand der Messstrecken abgefragt. T2 - Expertenforum Strukturmonitoring auf der Sensor+Test-Messe CY - Nuremberg, Germany DA - 08.06.2011 PY - 2011 AN - OPUS4-24047 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cabeza, Sandra A1 - Onorbe, Elvira A1 - Garces, Gerardo A1 - Perez, Pablo A1 - Klaus, Manuela A1 - Genzel, Christoph A1 - Adeva, Paloma T1 - The evolution of internal strain in Mg-Y-Zn alloys with a long period stacking ordered phase N2 - The load partition in Mg-Y-Zn system is studied by means of synchrotron diffraction. in-situ tensile tests disclose LPSO phases were for the first time proved to behave as an efficient reinforcement in Mg-Y-Zn alloys, therefore they could be treated as “short-fibre composite” for the modeling of mechanical behaviour. T2 - MECASENS CY - Grenoble, France DA - 16.09.2015 KW - Magnesium KW - LPSO KW - Synchrotron diffraction KW - Load partition PY - 2011 AN - OPUS4-38397 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Ebell, Gino A1 - Burkert, Andreas A1 - Gehlen, C. A1 - Keßler, S. T1 - Validierung zerstörungsfreier Messmethoden zur zuverlässigen Erfassung von Bewehrungskorrosion (Schlussbericht) N2 - Determining a pore structure’s mechanical and chemical data on lime rendering exposed outdoors and including masonry in the laboratory, with regard to their behaviour on moisture transport and weathering was the objective. In search of clues for a dose-response relation - i.e. upon a connection between the emission rate of SO2 and NOx on one hand and the degree of damage to mainly plaster having a lime component on the other - it has been of interest to what extent their structural characteristics including pore space are modified and so consequently also physico-technical properties and chemical composition. For determining corresponding criteria, a widely diversified spectrum of test methods such as to obtain data concerning porosity and moisture transport, mechanical behaviour, and chemistry as well is available. A description of the manufacture of plate-shaped rendering specimens with lime putty, industrially hydrated lime and dolomitic hydrate (the last two also having a cement admixture) and also hydraulic lime as binding agents is included. First deposition velocity and absorption rate for SO2 were determined in laboratory tests on these materials in dry and moist states. After their exposure on outdoor racks at six locations in the Berlin region with differing SO2 atmospheric contents over at least 5 years, the samples of course show timedependent modifications of chemical and physical qualities which are especially reflected in the form of profiles of structure, strength and concentration, e.g. for sulphate. Local climatic differences, however, partly exert a greater influence on material than emissions. Similar investigations were performed on samples of comparable composition exposed 4 and 17 years. But the real surprise is furnished by the renderings’ behaviour depending upon orientation and upon height at a building. Since weathering behaviour and moisture Transport (absorption, storage, release) are directly interdependent, further criteria are necessary for a critical assessment of a plasters’ pore structure. Starting from sands, plasters were characterized. The structural parameters were lastly influenced by the respective contents of sand, binder and mixing water. These results and those gained from bricks naturally find their expression in masonry sections manufactured there from, and above all in their capillary and evaporative behaviours, and also when applying different test liquids. Summary and cited literature is given at the end of this report. KW - Potentialfeldmessung KW - Potential mapping KW - Korrosion KW - Stahlbeton KW - Betonstahl KW - Merkblatt B 3 PY - 2011 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-336229 SP - 1 EP - 92 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) / Technische Universität München AN - OPUS4-33622 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kannengießer, Thomas A1 - Kromm, Arne T1 - Characterising phase transformations of different LTT alloys and their effect on residual stresses and cold cracking JF - Welding in the World N2 - Novel martensitic filler materials with specially adjusted martensite start temperatures (Ms) can counteract the cooling specific shrinkage due to expansion effects of the weld metal associated with phase transformations. That can be exploited to create compressive residual stresses in the weld and adjacent areas, i.e. beneficial for increasing fatigue strength. The Ms temperature is shifted via the chemical composition, mainly by the alloying elements nickel and chromium, resulting as well in different retained austenite contents. Investigations were made using different Low Transformation Temperature (LTT) alloys with varying nickel content. The resulting phase transformation temperatures were – for the first time – detected using high energy synchrotron diffraction and Single Sensor Differential Thermal Analysis (SS-DTA). Compared to angle dispersive diffraction, energy dispersive diffraction offers the possibility to measure residual stresses of the martensite and austenite phase parallel fast in one experiment up to depths of 100 µm. The residual stresses show significant distributions dependent on Ms temperature. The effect on the cold cracking behaviour of these alloys was investigated using the Tekken test. Results show that cold cracking can be avoided when appropriate contents of retained austenite are existent. KW - Austenite KW - Cold cracking KW - Martensite KW - Low themperature KW - Transformation PY - 2011 DO - https://doi.org/10.1007/BF03321286 SN - 0043-2288 VL - 55 IS - 3 SP - 48 EP - 56 PB - International Institute of Welding CY - France AN - OPUS4-38978 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Perret, Birgit A1 - Schartel, Bernhard A1 - Stöß, K. A1 - Ciesielski, M. A1 - Diederichs, J. A1 - Döring, M. A1 - Krämer, J. A1 - Altstädt, V. T1 - A new halogen-free flame retardant based on 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide for epoxy resins and their carbon fiber composites for the automotive and aviation industries JF - Macromolecular materials and engineering N2 - The pyrolysis and fire behavior of halogen-free flame-retarded DGEBA/DMC, RTM6 and their corresponding 60 vol.-% carbon fibers (CF) composites were investigated. A novel phosphorous compound (DOPI) was used. Its action is dependent on the epoxy matrix. DGEBA/DMC and DOPI decompose independently of each other. Only flame inhibition occurs in the gas phase. RTM6 shows flame inhibition and a condensed phase interaction increasing charring. Both mechanisms decrease with increasing irradiance, whereas in RTM6-CF charring is suppressed at low ones. RTM6+DOPI shows a higher LOI (34.2%) than DGEBA/DMC+DOPI and a V-0 classification in UL 94. Adding CF only enhances the LOI, DOPI+CF leads to a superposition in LOI for DGEBA/DMC-CF+DOPI (31.8%, V-0) and a synergism for RTM6-CF+DOPI (47.7%, V-0). KW - Composites KW - Flame retardancy KW - Glass transition KW - Pyrolysis KW - Thermosets PY - 2011 DO - https://doi.org/10.1002/mame.201000242 SN - 1438-7492 SN - 1439-2054 VL - 296 IS - 1 SP - 14 EP - 30 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-22957 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -