TY - CONF A1 - Daum, Werner T1 - Sensitive pultrudierte Tragwerke N2 - - Innovative Konstruktionskonzepte für den Leichtbau verwenden neue Material-Kombinationen - Erweiterte Anwendung der Sensortechnik bei der Entwicklung neuer Materialen - Integration von Sensoren in die Struktur, um synergetische Effekte effizienter auszunutzen und Eigenschaften zu steuern T2 - 2. TSB-TransferTreff "Materialeffizienz und Gestaltung" CY - Berlin, Germany DA - 11.06.2012 PY - 2012 AN - OPUS4-26464 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herbst, Tristan T1 - Integrated and holistic suitability assessment of recycling options for masonry rubble N2 - Behandelt den Bausektor und die Verarbeitsungsqualität T2 - European Geosciences Union (EGU) General Assembly 2012 CY - Vienna, Austria DA - 22.04.2012 PY - 2012 AN - OPUS4-25868 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herbst, Tristan T1 - Verwertung kieselsäurehaltiger Filterrückstände in mineralischen Baustoffen N2 - - jährlicher Anfall von 5.000 bzw. 10.000 Tonnen wasserhaltiger Filterrückstände (FR) pro Produzent bei der Abwasser-Neutralisation aus der Kieselsäure- bzw. Chlorsilanherstellung (FR1, FR2) - heute: Deponierung, Tagebauverfüllung - ungenutzte Sekundärrohstoffquelle - Untersuchung möglicher Anwendungsbereiche für FR T2 - GDCh Tagung Bauchemie CY - Dübendorf, Switzerland DA - 11.10.2012 PY - 2012 AN - OPUS4-26673 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maurer, G. T1 - Gas solubility in ionic liquids: Solubility of a binary gas mixture in a pure ionic liquid as well as of a single gas in a binary liquid mixture N2 - Ionic Liquids (ILs) are employed in various fields, for example, reaction engineering (reactions with gases, such as hydroformylation (CO, H2), hydrogenation (H2), oxidation (O2)) or separation technology (separations of gases, reactants, and high-volatility reaction products). For the basic engineering of such processes, knowledge of phase equilibria, particularly of mixtures, over a broad (p,T) range is mandatory. This contribution reports on recent experimental results from our laboratory: – for the simultaneous solubility of a binary gas mixture in a pure ionic liquid – for the solubility of a single gas in a binary liquid solvent mixture. T2 - EUCHEM 2012 Conference on Molten Salts and Ionic Liquids CY - Celtic Manor, Wales, United Kingdom DA - 05.08.2012 KW - ionic liquids KW - gas solubility KW - Henry's constant PY - 2012 AN - OPUS4-35947 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Marzok, Ulrich A1 - Müller, Ralf A1 - Schadrack, Reinhard A1 - Krauhausen, M. A1 - Reetz, R. T1 - Hochtemperatur-Laserprofilometrie für keramische Proben N2 - Das Hochtemperatur-Laserprofilometer der BAM4 ermöglicht eine 3D-Formerkennung an keramischen Folien oder anderen flachen Objekten während thermischer Behandlungen wie zum Beispiel bei laufenden Entbinderungs- oder Sinterprozessen. Mit dem Lasertriangulationssensor werden das Höhenprofil, die lateralen und axialen Schwindungen und andere charakteristische Maße der Probe wie die Folienbreite und -dicke, Abstände zwischen spezifischen Merkmalen oder Krümmungen bestimmt. Somit können insbesondere auch Deformationen und Verwerfungen der Objekte sowie Schwindungsinhomogenitäten an strukturierten Objekten erkannt und mit dem Herstellungsprozess verknüpft werden. T2 - DKG Jahrestagung 2012 CY - Nuremberg, Germany DA - 05.03.2012 KW - 3D-Formerkennung KW - Lasertriangulationssensor KW - Deformationen KW - Schwindungsinhomogenitäten PY - 2012 AN - OPUS4-35787 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Andrade, M. A. B. T1 - Numerical and experimental determination of the sound pressure distribution in single-axis acoustic levitators T2 - 2012 IEEE International Ultrasonics Symposium (IUS) CY - Dresden, Germany DA - 07.10.2012 KW - Acoustic levitation KW - Matrix method KW - Pressure field PY - 2012 N1 - Geburtsname von Buurman, Merwe: Albrecht, M. - Birth name of Buurman, Merwe: Albrecht, M. AN - OPUS4-27326 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rübner, Katrin T1 - Porenstruktur leichter Gesteinskörnungen aus Mauerwerkbruch N2 - Leichte Gesteinskörnungen mit Kornrohdichten < 2 g/cm³ werden industriell aus natürlichen Rohstoffen, wie Ton und Schiefer, hergestellt. Dabei fallen hohe Energiekosten an, während außerdem fortwährend die Verfügbarkeit geeigneter Rohstoffe sinkt. Eine Alternative stellen Leichtgranulate, die aus mineralischen Bau- und Abbruchabfällen hergestellt werden, dar. Im Forschungsprojekt „Aufbaukörnungen“ wurde eine Technologie zur Herstellung hochwertiger leichter Gesteinskörnungen aus Mauerwerkbruch entwickelt. Ziegelhaltige Bau- und Abbruchabfälle fallen in Deutschland mit bis zu 26 Mio. t pro Jahr an und weisen größere Verwertungsdefizite als Betonbruch auf. Der neuen Verwertungsstrategie liegt die Idee des rohstofflichen Recyclings zu Grunde. Die leichten Gesteinskörnungen werden am Ende eines mehrstufigen Herstellungsprozesses durch thermische oder hydrothermale Erhärtung im Labor- und halbtechnischen Maßstab produziert. Für Herstellungstechnologie und Eigenschaften der Leichtbetone sind neben Kornfestigkeit und Rohdichte die Porosität und Wasseraufnahme der leichten Gesteinskörnungen entscheidende Größen, die wiederum von Kornform, Oberflächenrauigkeit, Sinterschale und Porenstruktur der Körnungen beeinflusst werden. T2 - XVI. Porotec-Workshop über die Charakterisierung von feinteiligen und porösen Festkörpern CY - Bad Soden, Germany DA - 13.11.2012 PY - 2012 AN - OPUS4-27160 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Spranger, Holger T1 - THz-ToFD Tomography with Synthetic-Aperture-Aperture N2 - Terahertz-radiation (T-ray) are electromagnetic waves within a frequency range between 0,3 to 6 THz. T-rays are nonionising! They penetrate plastic, paper, ceramic and fabric. It is promising to use T-Rays for CT-applications to reveal uncertainties in dielectric materials. T2 - 8. THz-PhD-meeting CY - Marburg, Germany DA - 06.08.2013 KW - Terahertz Tomography synthetic aperture PY - 2013 AN - OPUS4-36223 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sojref, Regine T1 - Fused Silica Containing Powders for Low Sintering (1650°C) Mullite-Zirconia Composites T2 - 23rd International Congress on Glass CY - Prague, Czech Republic DA - 01.07.2013 PY - 2013 AN - OPUS4-30851 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maurer, G. T1 - High-pressure gas solubility in mixtures with one compound being an „alternative“ solvent N2 - The term „Alternative Solvents“ often refers to ionic liquids (ILs), mainly to distinguish these substances from traditional (i.e., molecular) solvents. In applications, any „alternative“ is required to perform better than something that is proven and tested. To bring ILs into practical use, availability and costs are the fundamental points to be addressed. There are two ways to proceed: ▬ tailoring a molecule, implanting the expected characteristics advantage: optimization of the targeted performance possible risks: outcome not always foreseeable, costly and time-intensive (“trial and error“) ▬ to target on mixtures of well-characterized ILs with molecular solvents advantage: substance characteristics are known, less costly, less time-consuming, mixture composition another tunable parameter risks: the same but with less impact For the basic engineering of technical processes, knowledge of phase equilibria, particularly of mixtures, over a broad (p,T) range is mandatory. This contribution reports on recent experimental results from our laboratory: ▬ the solubility of CO2 in a mixture of water and [bmim][CH3SO4] ▬ the solubility of CO2 in a mixture of methanol and [bmim][PF6] T2 - EUCHEM 2014 5th Conference on Molten Salts and Ionic Liquids CY - Tallinn, Estonia DA - 06.07.2014 KW - Ionic liquids KW - Gas solubility KW - Henry's constant PY - 2014 AN - OPUS4-35944 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Griesche, Axel T1 - Hydrogen in Iron visualized in 3D by neutron tomography N2 - Presented are neutron tomographies on hydrogen charged iron samples. T2 - RACIRI Summer School 2015 CY - Sellin, Rügen, Germany DA - 22.08.2015 KW - Tomographie KW - Wasserstoff KW - Neutronen KW - Hydrogen KW - Neutron KW - Tomography PY - 2014 AN - OPUS4-44838 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pfretzschner, Beate T1 - Hydrogen in blistered iron visualized in 3D by neutron tomography N2 - Presented are neutron tomographies on hydrogen charged iron samples. T2 - RACIRI Summerschool CY - Sellin, Germany DA - 22.08.2015 KW - Eisen KW - Neutronenradiographie KW - Wasserstoff PY - 2014 AN - OPUS4-47786 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Reinsch, Stefan T1 - Sintering and bloating phenomena of barium disilicate glass powders T2 - 88. Glastechnische Tagung DGG - ACerS GOMD 2014 CY - Aachen, Germany DA - 26.05.2014 PY - 2014 AN - OPUS4-30810 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Prewitz, Marc A1 - Müller, Ralf A1 - Marotzke, Christian A1 - Holtappels, Kai T1 - Characterization of glass capillary storage modules considering permeability and mechanical stress via finite elements N2 - Glass capillaries are potential candidates for long term hydrogen storage under high pressure. Burst pressure strongly drops with surface damaging, a polymer coating is needed. The aim is to study stress distribution within single coated glass capillaries sealed to metal fittings T2 - 88. Glastechnische Tagung DGG – ACerS GOMD 2014 CY - Aachen, Germany DA - 25.05.2014 KW - Burst test KW - Hydrogen storage KW - Polymer coating PY - 2014 AN - OPUS4-35784 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wu, Cheng-Chieh T1 - Inverse finite element adjustment of material parameters from integrated analysis of displacement field measurement N2 - The integration of finite element method (FEM) into the least-squares adjustment presented in is further extended for a joint evaluation of an elastostatic model and displacement field measurement. For linear solids which obey the Hooke's law, the material parameters determination from measurements is being examined. T2 - 32nd Danubia-Adria Symposium on advances in experimental mechanics CY - Starý Smokovec, Slovakia DA - 22.09.2016 KW - Integrated analysis KW - Inverse problem KW - Finite element method KW - Least-squares adjustment KW - Model and measurement based analysis PY - 2015 AN - OPUS4-35648 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cabeza, Sandra T1 - Low alloyed Mg-Y/RE-Zn alloys: mechanical and corrosion behaviour N2 - Mg-Y,RE-Zn systems present second phases with high thermal stability, promoting the increase of strength and creep resistance at high temperatures. Mg and its alloys have a potential application as biomaterials due to their biocompatibility and degradation behaviour. The dominant corrosion mechanism in those alloys is the microgalvanic corrosion through coupling of the more noble second phases with the Mg matrix, and therefore a low concentration of those was sought. T2 - Mg 2015 CY - Jeju, South Korea DA - 12.10.2015 KW - Magnesium KW - LPSO KW - Corrosion behaviour KW - Mechanichal behaviour PY - 2015 AN - OPUS4-38398 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fabry, Çağtay T1 - Sensorgestütztes MSG-Engspaltschweißen mit modifizierter Prozessführung (IGF-Nr. 17.923N / DVS-Nr. 03.111) N2 - Präsentation von Versuchsaufbau und Ergebnissen zu IGF-Projekt 17.923N. Darstellung einer Methodik zur automatisierten Regressionsmodellierung eines Lichtbogensensors zur Höhenführung mittels künstlicher neuronaler Netze durch Einbindung optischer Sensorik als Referenzmesswert. T2 - Sitzung DVS AG V 2.4 „Schweißen mit abschmelzender Elektrode MIG/MAG” CY - Berlin, Germany DA - 16.04.2018 KW - MSG-Engspaltschweißen KW - Automatisierung KW - Lichtbogensensorik KW - Künstliche neuronale Netze KW - Digitalisierung PY - 2015 AN - OPUS4-44543 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rütters, H. T1 - Combining CO2 Streams from Different Emitters – A Challenge For Transport And Storage Infrastructure N2 - The European Directive 2009/31/EC on the geological storage of CO2 envisages an open access of CO2 streams from different emitters to a nation- or even EUwide CO2 pipeline network if CO2 stream compositions meet “reasonable minimum composition thresholds”. As of today it is not known how such “composition thresholds” may be defined and which impurity levels may be viable in practical application. To set up recommendations for criteria and respective threshold values for CO2 stream compositions, the project “CLUSTER” will investigate how a dynamic interplay – both in terms of mass fluxes and compositions – of CO2 streams from regionally clustered CO2 sources sharing a transport and storage infrastructure will impact corrosion, e.g., of pipelines and plant components, and geochemical alteration of cap rocks and reservoir rocks. In addition, the behaviour of such a highly dynamic CCS system will be considered for an overall optimization of system design including CO2 stream mixing schemes and facilities or interim CO2 storage. T2 - TCCS-8 – The 8th Trondheim Conference on CO2 Capture, Transport and Storage CY - Trondheim, Norway DA - 16.06.2015 KW - Carbon capture KW - Carbon dioxide KW - Corrosion KW - CCS PY - 2015 AN - OPUS4-47018 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Sebastian A1 - Meng, Birgit A1 - Selleng, Christian T1 - A new sample holder for fast xrd investigation on UHPC N2 - A new sample holder is described in this poster. It was developed in BAM for fast XRD investigation on UHPC (ultra high performance concrete). Results measuring solid, i.e. not pulverized, samples are shown. T2 - GeoBerlin 2015 CY - Berlin, Germany DA - 04.10.2015 KW - Building Materials KW - UHPC KW - X-ray diffractometry PY - 2015 AN - OPUS4-36949 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maack, Stefan T1 - Elastic wave propagation of ultrasound in bituminous road surfaces – simulations and measurements N2 - Maintenance costs of road infrastructure are increasing steadily. Adverse environmental impacts on infrastructure get more and more important as well. Therefore, it is important to determine how limited financial resources can be directed with an optimum pay-out. The present study takes first steps towards the usage of low-frequency ultrasound as a tool to evaluate the road condition. T2 - International Symposium Non-Destructive Testing in Civil Engineering 2015 CY - Berlin, Germany DA - 15.09.2015 KW - Wave propagation KW - Ultrasonic KW - NDT KW - Simulation PY - 2015 AN - OPUS4-38837 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Ralf A1 - Behrens, H. A1 - Deubener, J. T1 - Impact of structure and relaxation on fatigue and micromechanical properties of oxide glasses: the role of volatiles and bonding state N2 - As subcritical crack growth (SCCG) can reduce tensile strength of glasses by many orders of magnitude, the potential for improvement of fatigue behaviour is most intriguing in developing ultra-strong glasses. An essential bottleneck is the basic understanding of the numerous interplaying pressure-, temperature- and water-affected relaxation phenomena at the crack tip and related toughening strategies. Therefore, the present project aims to advance the basic understanding of structural relaxation effects and local properties caused by increased water concentration and tensile stresses at the crack tip as they are a key for structural toughening designs to develop SCCG-free glasses and glass surfaces. Our first studies give clear evidence that glass structure and dynamics is strongly modified upon hydration of glasses. These changes are highly related to the nature of network formers but are affected as well by the counter ions (network modifier). Results of the 1st project part suggest that structural relaxation below glass transition temperature, i.e. overlapping of short-range (beta) and long-range (alpha) interactions can contribute to SCCG in water-free environments and that structurally dissolved water in the glasses can have decisive impact on this effect. In the 2nd project stage specific glasses compositions will be investigated to gain an improved understanding on the relation of sub-Tg relaxation and inert SCCG as well as to shed light to the related effects of dissolved water and its speciation. These glasses cover a broader range of different glass topologies and binding partners, whereby the coupling of alpha and beta relaxations is varied systematically by alkali-, alkaline earth ions and water species concentrations. Preparation of hydrous glasses (up to 8 wt% water) will be performed by high pressure syntheses. Structure will be resolved by NMR, Raman and IR spectroscopy while structural relaxation is accessed in the temperature and frequency domain using dynamic mechanical spectroscopy and ultrasonic damping. We will focus on measurements of inert SCCG (region III) conducting experiments in vacuum and dry gas atmospheres using indentation techniques and stressing of glass specimens in DCB geometry. Experimental data on SCCG will be provided to SPP groups, which deals with fatigue in metallic glasses and vice versa we will test theoretical predictions of ab-initio simulations of partner within SPP 1594 in order to quantify the effect of water on the crack tip. In summa topological factors controlling the subcritical crack growth with respect to water will be identified from which structural toughening designs for highly fatigue resistant-glasses can be derived. N2 - Subkritisches Risswachstum (SCCG) kann die Zugfestigkeit von Glas um viele Größenordnungen erniedrigen. Deshalb birgt die Verbesserung des Ermüdungsverhaltens ein hohes Potential für das topologische Design hochfester Gläser. Ein diesbezüglicher Engpass ist das Verständnis der zahlreichen interagierenden druck-, temperatur- und wasserbeeinflussten Relaxationsphänomene an der Rissspitze und hieraus abgeleitete Verstärkungsstrategien. Ziel des Projekts ist es daher, das grundlegende Verständnis der Effekte, die infolge erhöhter Wasserkonzentrationen und Zugspannungen an der Rissspitze entstehen, zu vertiefen, da sie als ein Schlüssel für künftige strukturelle Designprinzipien zur Entwicklung schadenstoleranter Gläser und Glasoberflächen gelten. Unsere ersten Studien zeigen, dass die Struktur und Dynamik von Gläsern nach einer Hydration stark verändert sind. Diese Modifikationen sind mit der Art der Netzwerkbildner stark verknüpft, aber auch von ihren Gegenionen (Netzwerkwandler) abhängig. Die Ergebnisse des ersten Projektabschnitts legen nahe, dass strukturelle Relaxation unterhalb der Glasübergangstemperatur, d. h. ein Überlappen von kurz-reichweitigen (beta) und lang-reichweitigen (alpha) Wechselwirkungen, zum subkritisches Risswachstum in wasserfreien Umgebungen beitragen kann und, dass strukturell gelöstes Wasser in Gläsern sich entscheidend auf diese Effekt auswirken kann. Im zweiten Projektabschnitt werden daher spezielle Glaszusammensetzungen untersucht, die zu einem besseren Verständnis der Verbindung zwischen sub-Tg Relaxation und SCCG führen aber auch den Einfluss von gelöstem Wasser und dessen Speziation näher beleuchten. Diese Gläser weisen eine großen Breite an verschiedenen Topologien und Bindungspartnern auf, wobei die Kopplung von alpha und beta Relaxation durch Veränderungen in den Gehalten von Alkali-, Erdalkalionen und der Wasserspezies systematisch variiert wird. Die Präparation hydratisierter Gläser (bis zu 8 Ma.%) erfolgt mittels Hochdrucksynthesen. Die Glasstruktur wird durch NMR, Raman und IR Spektroskopie aufgeklärt während die Strukturrelaxation anhand dynamische mechanische Spektroskopie und Ultraschalldämpfung im Temperatur- und Frequenzraum erfasst wird. Im Fokus werden Messungen des inerten subkritischen Risswachstums (Region III) stehen, die Indenter-Experimente im Vakuum und trockenen Gasatmosphären sowie Verspannen von Glasproben in DCB Geometrie beinhalten. Experimentelle SCCG Daten werden Gruppen im Schwerpunktprogramm zur Verfügung stellen, die sich mit Ermüdung in metallischen Gläsern beschäftigen und im Gegenzug werden wir theoretische Vorhersagen aus ab initio Simulationen der Partner im SPP 1594 testen, um den Einfluss von Wasser auf die mechanischen Eigenschaften an der Rissspitze und deren Einfluss auf SCCG zu quantifizieren. In summa werden topologische Faktoren bezüglich Wasser, die SCCG kontrollieren, identifiziert, um daraus Designprinzipien für hoch ermüdungsresistente Gläser abzuleiten. T2 - Kolloquium des DFG-PP 1594 CY - Jena, Germany DA - 17.9.2015 KW - Glass KW - Fatigue PY - 2015 AN - OPUS4-38334 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Selleng, Christian T1 - Effect of 90°C thermal treatment on Ultra-High Performance Concrete N2 - Ultra High Performance Concrete (UHPC) is characterized by high strength and high durability. This is achieved by an optimized grain size distribution, especially within fine grains, and addition of superplasticizer, which allow the reduction of the water/cement ratio in the cement paste and thereby the increase of the density of UHPC. Thermal treatment, i.e. curing at elevated temperature and pressure, contributes to a further increase of compressive strength. The aim of the presented study was to analyze the effect of thermal treatment at 90 ◦C and atmospheric pressure on UHPC samples. Varying factors were the age of the samples when heat treatment started (initial storage time), the duration of heat treatment and the type of heat treatment. It was applied in three ways: 1. treated without any protection, 2. sealed in plastic foil and 3. treated in hot water. Afterwards the samples were analyzed with respect to their mechanical properties and their phase composition. Furthermore, the weight (water absorption) of the samples was observed over 28 days and was correlated with the strength test results. The development of strength depends on the combination of initial storage time and the duration of heat treatment and is also influenced by the type of thermal treatment. The highest compressive strengths have been observed by implementing the hot water treatment. Thereby the weight of the samples increase due to additional absorbed water. This enables an increased hydration of cement clinker inducing a higher strength. T2 - GeoBerlin 2015: Dynamic Earth - from Alfred Wegener to today and beyond CY - Berlin, FU Berlin DA - 04.10.2015 PY - 2015 AN - OPUS4-34504 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Blaeß, Carsten T1 - Sintering and crystallization of new bioactive glasses N2 - Bioglass® 45S5 is mainly used clinically as powders, granules or pastes instead of sintered compacts. This is due to the inherent problem of crystallization during the sintering, which results in poor mechanical properties and reduced bioactivity. Recently, new bioactive glasses with improved crystallization stability have been developed as promising candidates for manufacturing of sintered powder compacts for bone regeneration, which combine improved sintering behavior with bioactivity. Compared with the well-known Bioglass® 45S5 (SiO2-P2O5-CaO-Na2O) the calcium/alkali oxide ratio was increased, sodium oxide was partially replaced by potassium oxide and up to 3 mol% calcium fluoride were added, in order to stabilize the glass against crystallization. The aim of this study was to investigate the sintering and crystallization behavior of these new bioactive glasses. Sintering and crystallization were characterized by heating microscopy, XRD, FTIR, SEM, and DTA. The results show that a sintered density of 88-99 % is achieved in contrast to only 57-67% for Bioglass® 45S5. In addition, FTIR and XRD analyses show that Bioglass® 45S5 crystallized during sintering while for the new glasses no crystalline phases are detected. The thermal properties of all glasses were studied by DTA measurements, and the influence of grain size was characterized. These studies showed that full densification can be attained for particle size < 32 µm, whereas coarser particles progressively increase residual porosity. Observed foaming phenomena, are strongly retarded by crystallization of beta-HAp. T2 - ICG 2016 CY - Shanghai, China DA - 07.04.2016 KW - Bioactive KW - Glass KW - Crystallization KW - Sintering PY - 2015 AN - OPUS4-38304 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Blaeß, Carsten T1 - New bioactive glasses with improved sintering behavior N2 - Nowadays, the use of bioactive glasses is established for bone regeneration; however glasses are used mostly as powders, granules or in a paste. Sintered scaffolds are not used clinically, because of the in inherent problem of crystallization during the sintering process, resulting in poor mechanical properties and reduced bioactivity. The aim of this study was therefore to design new bioactive glasses, which combine improved processing and sintering with bioactivity. Compared with the well-known Bioglass® 45S5 (SiO2-P2O5-CaO-Na2O) the calcium/alkalioxide ratio was increased, sodiumoxide was partially replaced by potassiumoxide and up to 8 mol% calciumflorid were added, in order to stabilize the glass against crystallization. The sintering behavior of the new glasses was characterized by heating microscopy and compared to Bioglass® 45S5. The results showed that the new glasses achieved a sintered density of 88-99 % in contrast to only 57-67% for Bioglass® 45S5. In addition FTIR and XRD analyses showed that Bioglass® 45S5 crystallized during sintering while for the new glasses no crystalline phases were detected. The thermal properties of all glasses were studied by DTA and DSC measures, and the influence of grain size and heating rate were characterized. These studies showed a shift of start and end temperature of sintering process as well as the final density. The structure of sintered specimens during and after sintering was examined using light and electron microscopy (REM). T2 - Crystallization 2015 CY - Nagaoka, Japan DA - 11.10.2015 KW - Bioactive KW - Glass KW - Crystallization KW - Sintering PY - 2015 AN - OPUS4-38308 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agudo Jácome, Leonardo T1 - Nano-sized precipitates in an Fe-13Cr alloy formed under oxidizing water vapor atmosphere N2 - Oxidation of a Fe-13Cr alloy under water vapor at 600 °C produced a zone of nano-sized precipitation underneath the outside scale formed by iron oxides and Fe‒Cr spinel. The majority of the spinel layer shows a mixed orientation relationship to the ferritic matrix {100}α || {100}sp & <011>α || <001>sp. However, also the discovered precipitated particles are characterized by the same crystallographic orientation relationship to the respective ferritic parent grain. The habit of the precipitates is best described by a lath morphology with their main axis parallel to <100> of ferrite. Energy dispersive X-ray spectroscopy (EDX) and electron backscatter diffraction (EBSD) in an scanning electron microscope (SEM) have been applied to characterize the oxide layer in the micrometer scale. The clearly smaller precipitates were subsequently investigated by transmission electron microscopy (TEM). Specimens have been prepared by focused ion-beam (FIB) milling at an area previously characterized by EBSD. They cover the ferritic base material, but mainly the precipitation zone and the Fe‒Cr spinel layer. Energy filtered selected area diffraction (SAD) in the conventional (C)TEM and high-angle annular darkfield (HAADF) imaging in the scanning (S)TEM mode were employed in the characterization of the specimens. T2 - International Conference on Solid-Solid Phase Transformations in Inorganic Materials (PTM) 2015 CY - Whistler, British Columbia, Canada DA - 28.06.2015 KW - Precipitation KW - Oxidation KW - Microscopy KW - Topotactic transformation KW - Spinel PY - 2015 AN - OPUS4-42169 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rübner, Katrin T1 - Studies on the Pore Structure of Lightweight Recycling Granules N2 - Lightweight granules are mineral, spherical and porous particles with bulk density less than 2000 kg m . New types of lightweight granules are made from masonry -3 rubble as an alternative to the commonly used expanded clay and shale. They are produced in a multistage manufacturing process by thermal or hydrothermal treatment. Studies of the microstructure of the new lightweight granules are very important to optimise the engineering properties with regard to different applications from lightweight concrete to planting substrates and wastewater treatment. Here, the results of porosity and pore structure measurements are presented. Characteristic samples with different bulk densities of both thermally and hydrothermally hardened granules have been analysed by means of various methods. T2 - 27. Deutsche Zeolith-Tagung CY - Oldenburg, Germany DA - 25.02.2015 PY - 2015 AN - OPUS4-32835 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Laquai, René A1 - Schaupp, Thomas A1 - Müller, Bernd R. A1 - Griesche, Axel A1 - Bruno, Giovanni A1 - Kannengießer, Thomas T1 - 3D imaging of hydrogen assisted cracking using analyser-based imaging N2 - To better understand the mechanism of hydrogen assisted cracking (HAC), it is important to investigate the 3D structure of the cracks non-destructively. Since, cracks introduced by HAC are usually very small, conventional x-ray imaging methods often lack the required spatial resolution. However, the detection of those cracks can be enhanced by taking advantage of refraction at interfaces within the sample. To image this refractive deflection we employ analyser based imaging (ABI). In this work we aim at proving the enhanced crack detection of ABI by investigating an alluminum alloy weld. T2 - BESSY User Meeting 2015 CY - Berlin, Germany DA - 09.12.2015 KW - X-ray refraction KW - Synchrotron KW - Analyser-based imaging KW - Hydrogen assisted cracking KW - Welding PY - 2015 AN - OPUS4-38278 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Shashev, Yuri T1 - Optimizing the performance of phase gratings for better visibility in Talbot- Lau interferometry N2 - We investigated the efficiency of phase gratings, i.e., the visibility upon variation of different parameters. Rotating around an axis parallel to the grid lines of the phase grating changes the grating’s shape and thereby the initial distribution of phase shifts. This yields high visibilities for shorter propagation distances than derived from box shapes. Tilting the grating in the scattering plane allows continuous tuning of the grating’s height that corresponds to an ideal phase shift for a particular photon energy. This opens the way for tuning the design energy suitable for the material under investigation. Our study included simulations for monochromatic sources with the sampling procedure. T2 - PhD Day 2015 CY - Berlin, Germany DA - 14.7.2015 KW - Talbot-Lau interferometry PY - 2015 AN - OPUS4-38325 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stroh, Julia T1 - High resolution in situ monitoring of the initial cement hydration influenced by organic admixtures N2 - Numerous admixtures are used in the building practice to customize the properties of the cement paste during application. The influences of admixtures on the course of cement hydration and formation of hydrate phases have to be considered. Polycarboxylate ether (PCE) based polymeric superplasticizers (SPs) are known to retard the setting of the cement paste. The extent of the retardation differs depending on the molecular structure of the SP. Additionally, the presence of a stabilizing agent (SA) in the cement paste has a retarding side effect on the setting. The initial cement hydration processes and the detailed mechanisms of the retardation influenced by PCEs, as well as their interactions with particular SAs, are insufficiently understood. Up to now, only the results of phenomenological studies were taken into account to describe this retardation process. A detailed structure analysis monitoring the change of the phase composition during the hydration was never applied. Both SP and SA affect the adsorption of the sulphate ions on the clinker particles, causing changes in the formation of ettringite during the initial hydration, and are therefore a crucial part of the setting process itself. Here, the initial hydration of cement influenced by the interaction of SP and SA was monitored in situ by synchrotron X-ray diffraction. The high time resolution of the measurements allowed a continuous detection of the hydrates formed. The hydration was followed from the starting point of water addition and for couple of hours afterwards. The hydration of the levitated cement pellets containing starch as SA was initialized by adding aqueous solutions of different commercial SPs. Changes in the ettringite formation were detected in comparison to the reference hydration of pure cement. T2 - Early Age Concrete: From the Research Lab to the Construction Site CY - Tomsk, Russia DA - 02.06.2015 KW - Portland cement KW - Initial hydration KW - Superplasticizer KW - Stabilizer KW - Synchrotron XRD PY - 2015 AN - OPUS4-35470 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Oesch, Tyler T1 - In-situ CT investigation of pull-out failure for reinforcing bars embedded in conventional and high-performance concretes N2 - The use of high-performance concretes holds great promise for many structural applications. This paper investigates the performance of these materials when used in combination with traditional reinforcing bars. An improved understanding of failure during reinforcing bar pull-out from high-performance concretes is needed in order to better predict the embedment length required to develop full reinforcing bar pull-out strength and the required thickness of reinforcing bar cover for adequate corrosion protection. The cracking structures surrounding the reinforcing bars were analyzed using x-ray computed tomography (CT) in order to determine the stress states causing failure. This was accomplished by conducting in-situ reinforcing bar pull-out experiments during CT scanning. A conventional concrete, a high-strength concrete, and a high-strength fiber reinforced concrete were all tested during the experiments. The results of these experiments showed that the levels of brittleness of the different concrete materials had a major impact on the failure mechanisms that they experienced during reinforcing bar pull-out. It was also clear that the specimen geometry and the casting method had a major impact on fiber orientation. The inclusion of fibers within concrete was also found to significantly improve strength and corrosion protection during reinforcing bar pull-out. T2 - 6th Conference on Industrial Computed Tomography CY - Wels, Austria DA - 09.02.2016 KW - Fiber KW - Reinforcing Bar KW - Computed Tomography KW - In-Situ KW - High-Performance Concrete PY - 2016 AN - OPUS4-35521 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Taabache, Soraya T1 - Microfluidic-Assisted Self-Assembly of Dendritic Amphiphiles N2 - The controlled production of supramolecular aggregates formed by the self-assembly of dendritic amphiphiles is of great interest owing to their potential application in the fields of nanotechnology and nanomedicine. Dendritic amphiphiles as building blocks offer the advantage that their structure and size can be precisely tuned through organic synthesis. This synthetic flexibility enables the fine-tuning of the hydrophobic to hydrophilic ratio of the dendritic segments, which mainly controls the morphology of the self-assembled structures. A promising method for the controlled preparation of supramolecular assemblies is based on the use of micromixers.[5,6] Due to their mixing times in the range of milliseconds at the microscale level, the application of such microfluidic systems benefits from a high mixing efficiency, a low mixing time and a reproducible synthesis compared to conventional batch-based techniques such as the solvent injection method or the film hydration method. Herein, we report on the microfluidic-assisted self-assembly of several dendritic amphiphiles and the impact of the mixing parameters on the self-assembly process. T2 - Makromolekulares Kolloquium 2016 CY - Freiburg im Breisgau, Germany DA - 24.02.2016 KW - Dendritic amphiphiles KW - Self-assembly KW - Dendrimersomes KW - Micromixer KW - Microfluidic PY - 2016 AN - OPUS4-35477 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Steinborn, Gabriele T1 - Stable aqeous niobium carbide suspensions for production of homogeneous hard materials N2 - Hard materials consist of a hard phase embedded in a metallic binder. In order to achieve high toughness and strength, it is necessary to have a perfect mixing of hard phase and binder, which is mainly achieved by ball milling. Niobium carbide (NbC) has a high potential to substitute tungsten carbide as hard material. The publication presents the development of stable homogeneous and de-agglomerated NbC-dispersions. To prevent agglomeration of the powder, stable suspensions were achieved by surface treatments with the dispersants (PD and HD), which resulted in a charge reversal from a negative to a positive zeta potential. This surface-modified powder guaranteed a stable re-dispersion in the binder suspension. Nickel powder was added as metallic binder. This suspension was suited for 3D-printing. The green samples could be sintered in vacuum or Argon atmosphere. T2 - 91. Jahrestagung der deutschen keramischen Gesellschaft CY - Freiberg, Germany DA - 07.03.2016 KW - Niobium carbide powder KW - Stable suspensions KW - Reduction of agglomerates PY - 2016 AN - OPUS4-35636 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bonse, Jörn T1 - Mimicking lizard-like surface structures upon ultrashort laser pulse irradiation of inorganic materials N2 - The wetting behavior of material surfaces can be controlled by surface structures. We functionalized inorganic material surfaces, such as steel, titanium alloy and silicon, to modify the wetting behavior using ultrashort laser pulses (fs- to ps-range). The laser processing was performed by scanning the laser beam across the surface of initially polished flat sample material. A combined experimental and theoretical study of the laser processing parameters (peak fluence, scan velocity, line overlap) allowed the identification of different regimes associated with characteristic surface morphologies (laser-induced periodic surface structures, grooves, micro cones, dimples, etc.). Analyses of the surface using optical as well as scanning electron microscopy allowed the identification of morphologies providing the optimum similarity to the natural skin of lizards. For mimicking skin structures of moisture-harvesting lizards towards an optimization of the surface wetting behavior, additionally, a two-step laser processing strategy was established for realizing hierarchical micro- and nanostructures. In this approach, a laser-generated regular array of small dimples was superimposed (step 2) to the micron-scaled capillaries processed before (step 1). Optical focus variation imaging measurements finally revealed the three dimensional topography of the laser processed surfaces derived from lizard skin structures. The functionality of these surfaces was analyzed in view of wetting properties. T2 - E-MRS 2016 Spring Meeting, Symposium C: "Laser-material interactions for tailoring future applications" CY - Lille, France DA - 02.05.2016 KW - Laser-induced periodic surface structures (LIPSS) KW - Femtosecond laser ablation KW - Steel KW - Lizard KW - Wetting PY - 2016 AN - OPUS4-36047 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bonse, Jörn T1 - Tribological properties of femtosecond laserinduced periodic surface structures on metals N2 - Laser-induced periodic surface structures (LIPSS, ripples) were generated on steel and titanium surfaces upon irradiation with multiple linear polarized femtosecond laser pulses (pulse duration 30 fs, central wavelength 790 nm). The experimental conditions (laser fluence, spatial spot overlap) were optimized in a sample-scanning geometry for the processing of large surface areas covered homogeneously by the nanostructures. The irradiated surface regions were subjected to optical microscopy (OM), white light interference microscopy (WLIM) and scanning electron microscopy (SEM) revealing sub-wavelength spatial periods. The nanostructured surfaces were tribologically tested under reciprocal sliding conditions against a sphere of hardened 100Cr6 steel at 1 Hz using paraffin oil and engine oil as lubricants. After 1000 sliding cycles at a load of 1.0 N, the corresponding wear tracks were characterized by OM and SEM. For specific conditions the laser-generated nanostructures endured the tribological treatment. Simultaneously, a significant reduction of the friction coefficient was observed in the laser-irradiated (LIPSS-covered) areas when compared to the non-irradiated surface, indicating the potential benefit of laser surface structuring for tribological applications. T2 - SPIE Photonics West Conference, Symposium "Laser Applications in Microelectronic and Optoelectronic Manufacturing" (LAMOM) XXI CY - San Francisco, CA, USA DA - 13.02.2016 KW - Femtosecond laser ablation KW - Laser-induced periodic surface structures (LIPSS) KW - Tribology KW - Friction KW - Wear PY - 2016 AN - OPUS4-36041 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kirner, Sabrina T1 - Femtosecond laser-induced periodic surface structures on titanium nitride coatings for tribological applications N2 - Laser-induced periodic surface structures (LIPSS) were generated on titanium nitride (TiN) hardcoating surfaces (deposited on metallic substrates) upon irradiation with multiple linearly polarized femtosecond laser pulses in air (30 fs duration, 790 nm wavelength, 1 kHz pulse repetition rate). The conditions were optimized in a sample-scanning geometry for the processing of large surface areas (5 mm x 5 mm) covered homogeneously by nanostructures with sub-wavelength periods ranging between ~200 nm and 700 nm. For these nanostructures the coefficient of friction was characterized under reciprocating sliding condition against a ball of hardened steel at 1 Hz using different lubricants (regime of mixed friction). After 1000 cycles, the corresponding wear tracks were characterized by optical and scanning electron microscopy. High-resolution energy dispersive X-ray analyzes (EDX) allowed the visualization of chemical alterations within the wear tracks. For specific conditions, the nanostructures endured the tribological treatment. Our experiments provide a qualification of the tribological performance of the fs-LIPSS on TiN surfaces. T2 - E-MRS 2016 Spring Meeting, Symposium C: "Laser-material interactions for tailoring future applications" CY - Lille, France DA - 02.05.2016 KW - Femtosecond laser ablation KW - Laser-induced periodic surface structures (LIPSS) KW - Tribology KW - Friction KW - Wear KW - Titanium nitride PY - 2016 AN - OPUS4-36042 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Naghib-zadeh, Hamid T1 - High-strength and gas-tight ceramic-ceramic joints by RAB composite tapes N2 - Ceramic components with complex shape cannot be produced frequently by usual ceramic forming and sintering processes. Therefore, numerous joining methods were developed and introduced in industrial scale. Nowadays, multi-stage Mo-Mn-process and active brazing are preferentially used, if temperature-stable and gastight joints are required. Unfortunately, both processes involve cost-intensive thermal processes: hydrogenous atmosphere is essential for metallization in Mo-Mn-process and active brazing takes place under vacuum. Thermal processes can be drastically simplified by using Reactive Air Brazing (RAB). Joining under air atmosphere is an interesting alternative, especially to join oxide ceramic components among themselves. So far, main disadvantage of RAB is low strength of join connections. Aim of this investigation was the development of high-strength, thermal shock resistant and gastight ceramic-ceramic joints by RAB. Therefore, - commercial, silver and copper oxide containing RAB soldering composition was modified by addition of ceramic particles with low thermal expansion coefficients (TEC). Hence, thermal misfit between TEC of solder and ceramic components was significantly reduced. - RAB soldering paste was replaced with newly developed RAB composite tapes, produced by ceramic “doctor blade” technology. Thereby, improved potential exist to tailor the brazing layer relating to composition, thickness and thickness uniformity. Gastight alumina-alumina, alumina-zirconia and zirconia-zirconia joints with strongly improved strength were produced by novel composite tapes. No strength degradation of joints was observed after thermal cycling up to 700°C. T2 - Jahrestagung der Deutschen Keramischen Gesellschaft (DKG) 2016 CY - Freiberg, Germany DA - 07.03.2016 KW - Brazing KW - Compsite tapes KW - Ceramic-ceramc joints PY - 2016 AN - OPUS4-36114 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Spranger, Holger T1 - THz-ToF techniques for the detection of inherent discontinuities in dielectric materials based on SAFT N2 - The ability to penetrate dielectric materials makes T-rays attractive to reveal discontinuities in polymer and ceramic materials. Changes of travelling time (ToF) and pulse shape due to the interactions of THz pulses with the dielectric material and its inherent discontinuities can be observed. A tomogram of the object under the test can be reconstructed from time of flight diffraction (ToFD) scans if a synthetic focusing aperture (SAFT) algorithm is applied. T2 - 7th International Workshop on Terahertz Technology and Applications CY - Kaiserslautern, Germany DA - 15.03.2016 KW - Terahertz synthetic aperture dielectric materials PY - 2016 AN - OPUS4-36221 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Madkour, Sherif T1 - Evidence of a Three-Layred Structure in Ultrathin PVME and PVME-PS Blend Films by Nanosized Relaxation Spectroscopy N2 - In the course of miniaturizing modern technology down to the molecular scale, much remain unknown about the materials behavior and the deviations from the bulk that might arises from confinement effects. Here, a combination of nano-sized relaxation spectroscopies (Broadband dielectric spectroscopy (BDS) and Specific heat spectroscopy (SHS); employing AC nanochip calorimetry) were utilized to investigate the glassy dynamics of ultra-thin films of Poly (vinyl methyl ether) (PVME) and of blends PVME / Polystyrene (PS) 50:50 wt-%,, which are miscible in bulk (thicknesses: ca. 8 nm – 160 nm, film thickness was controlled by ellipsometry, film topography by AFM). Both methods are sensitive to different probes; where SHS senses entropy fluctuations while BDS measures dipole fluctuations. For BDS measurements, a recently developed nano-structured electrode sample arrangement is employed, where ultra-thin films are spin-coated on an ultra-flat highly conductive silicon wafer, sandwiched between a wafer with nanostructured SiO2 nano-spacers with heights between 35 nm and 70 nm. For PVME films, two thickness independent processes were observed and interpreted to be the α-processes of a bulk-like layer and a process due to an absorbed layer to the substrate. This adsorbed layer further undergoes a confinement effect that results in the localization of the segmental dynamics, which results in an Arrhenius-like temperature dependence. A detailed analysis of the dielectric strengths of both processes reveals that the thickness of the adsorbed layer decreases with increasing temperature, while that of the bulk-like layer increases. For the blend system, by measuring the dynamic Tg in dependence of the film thickness, SHS showed that the Tg of the whole film was strongly influenced by a nanometer-thick surface layer at the polymer/air interface due to a self-assembling process. The dynamic Tg obtained from the SHS measurements decreased with decreasing film thickness. On the other hand, BDS measurements showed a completely different behavior. At high temperatures, the temperature dependence of the relaxation times of the films follows that of bulk-like PS/PVME; obeying the VFT-law. With decreasing temperature, the temperature dependence deviates from the VFT to an Arrhenius law; where the apparent activation energy decreases with decreasing film thickness. This is the first example where confinement induced changes were observed by BDS for ultra-thin films. All results were analyzed in detail in a comprehensive discussion. T2 - 14. Lähnwitzseminar on Calorimetry CY - Rostock-Warnemünde, Germany DA - 05.05.2016 KW - Ultra-Thin films PY - 2016 AN - OPUS4-36477 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sentker, K. A1 - Yildirim, Arda T1 - Columnar axial orientation of discotic liquid crystals in nanoporous solids N2 - Successful implementation of an optical polarimetry measurement setup. Due to wall anchoring interactions HAT6 embedded in an untreated alumina membrane exhibits a radial orientation for pore sizes in between 30 nm and 80 nm. Embedded in large membranes, pore size of 180 nm, HAT6 forms the favored hexagonal columnar phase along the pore axis. T2 - 80. Jahrestagung der DPG und DPG-Frühjahrstagung CY - Regensburg, Germany DA - 06.03.2016 KW - Discotic Liquid Crystals KW - Nanoconfinement KW - Orientation PY - 2016 AN - OPUS4-36479 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Walter, Astrid T1 - EU-Projekt HOMER, home made explosives (HMEs) and recipes characterisation N2 - Das EU-Projekt HOMER befasst sich mit den sogenannten Home Made Explosives (HMEs) und frei verfügbaren Rezepten für deren Herstellung. Diese Selbstlaborate spielen in der heutigen Zeit vor allem im Zusammenhang mit terroristischen Aktivitäten eine bedeutende Rolle. Informationen zu HMEs und ihrer Herstellung werden einfacher denn je über das Internet verbreitet. Hier knüpft das im 7. EU‑Forschungsrahmenprogramm finanzierte Projekt an und bezweckt, die im Internet verfügbaren Quellen auszuwerten und so die Informationslage für Sicherheitskräfte und Ermittlungsbehörden zu verbessern. Im Rahmen des Projektes wird eine automatisierte Suche von Rezepten im Internet entwickelt. Die gefundenen sowie die im Projekt generierten Informationen über HMEs sollen im Endergebnis in Form einer Software (Knowledge Management Platform) informationstechnisch nutzbar gemacht werden. Diese Datenbank soll auch für mobile Geräte zur Verfügung stehen. Der Schwerpunkt der Projektbeteiligung des Fachbereichs 2.3 Explosivstoffe der BAM liegt in der Bewertung der Rezepturen und der auf ihrer Grundlage hergestellten Laborate. Es wurden HMEs entsprechend der vorgefundenen Rezepte und unter Beachtung aller notwendigen Sicherheitsvorkehrungen hergestellt und anschließend sicherheitstechnisch geprüft und bewertet. Dabei wurden sowohl Handhabungsparameter wie die Empfindlichkeiten gegen Schlag, Reibung und thermische Einflüsse ermittelt, als auch die Leistungsparameter wie Detonationsgeschwindigkeit und Luftstoßdruckwirkung gemessen. Die gewonnen Erkenntnisse fließen in die genannte Datenbank ein und sollen beispielsweise Einsatzkräften vor Ort helfen, angemessene Schutzabstände zu ermitteln. Auch das Personal in Laboren der Kriminalämter profitiert von der zusammengetragenen Information über HMEs bei der Analyse von unbekannten Explosivstoffspuren. T2 - 14. BAM-PTB-Kolloquium zur chemischen und physikalischen Sicherheitstechnik CY - Berlin, Germany DA - 14.06.2016 KW - Homemade explosives KW - Explosivstoffe KW - TATP KW - Ammoniumnitrat PY - 2016 AN - OPUS4-36594 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Bestimmung von Korrosionsabträgen an Zink mittels gelartiger Elektrolyte N2 - Das Poster zeigt eine Methode zur Bestimmung von Korrosionsraten und Korrosionsabträgen an Zink durch Verwendung von gelartigen Elektrolyten. T2 - Jahrestagung 2016 der GfKORR CY - Frankfurt/Main, Germany DA - 15.11.2016 KW - Gelartige Elektrolyte KW - Gel-type electrolytes KW - Verzinkungen KW - Zinc coatings KW - Korrosionsabtrag KW - Corrosion loss PY - 2016 AN - OPUS4-38298 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Reinemann, Steffi T1 - Untersuchung des Einflusses industrieller Korundschleifprozesse auf die Korrosionsbeständigkeit nichtrostender Stähle mittels KorroPads N2 - Das Poster stellt aktuelle Eregbnisse des AiF-Vorhabens 18823 N/1 zum Einfluss von Schleifprozessen auf die Korrosionsbeständigkeit nichtrostender Stähle vor. T2 - Jahrestagung 2016 der GfKORR CY - Frankfurt/Main, Germany DA - 15.11.2016 KW - Korrosion KW - Corrosion KW - Korundschleifen KW - Corundum grinding KW - Nichtrostende Stähle KW - Stainless steels PY - 2016 AN - OPUS4-38299 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Madkour, Sherif T1 - Evidence of a three-layred structure in ultrathin PVME and PVME-PS blend films by nanosized relaxation spectroscopy N2 - In the course of miniaturizing modern technology down to the molecular scale, much remain unknown about the materials behavior and the deviations from the bulk that might arises from confinement effects. Here, a combination of nano-sized relaxation spectroscopies (Broadband dielectric spectroscopy (BDS) and Specific heat spectroscopy (SHS); employing AC nanochip calorimetry) were utilized to investigate the glassy dynamics of ultra-thin films of Poly (vinyl methyl ether) (PVME) and of blends PVME / Polystyrene (PS) 50:50 wt-%,, which are miscible in bulk (thicknesses: ca. 8 nm – 160 nm, film thickness was controlled by ellipsometry, film topography by AFM). Both methods are sensitive to different probes; where SHS senses entropy fluctuations while BDS measures dipole fluctuations. For BDS measurements, a recently developed nano-structured electrode sample arrangement is employed, where ultra-thin films are spin-coated on an ultra-flat highly conductive silicon wafer, sandwiched between a wafer with nanostructured SiO2 nano-spacers with heights between 35 nm and 70 nm. For PVME films, two thickness independent processes were observed and interpreted to be the α-processes of a bulk-like layer and a process due to an absorbed layer to the substrate. This adsorbed layer further undergoes a confinement effect that results in the localization of the segmental dynamics, which results in an Arrhenius-like temperature dependence. A detailed analysis of the dielectric strengths of both processes reveals that the thickness of the adsorbed layer decreases with increasing temperature, while that of the bulk-like layer increases. For the blend system, by measuring the dynamic Tg in dependence of the film thickness, SHS showed that the Tg of the whole film was strongly influenced by a nanometer-thick surface layer at the polymer/air interface due to a self-assembling process. The dynamic Tg obtained from the SHS measurements decreased with decreasing film thickness. On the other hand, BDS measurements showed a completely different behavior. At high temperatures, the temperature dependence of the relaxation times of the films follows that of bulk-like PS/PVME; obeying the VFT-law. With decreasing temperature, the temperature dependence deviates from the VFT to an Arrhenius law; where the apparent activation energy decreases with decreasing film thickness. This is the first example where confinement induced changes were observed by BDS for ultra-thin films. All results were analyzed in detail in a comprehensive discussion. T2 - Polydays 2016 CY - Potsdam, Germany DA - 28.09.2016 KW - Ultra-Thin films PY - 2016 AN - OPUS4-38188 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bettge, Dirk A1 - Sonnenburg, Elke A1 - Klinger, Christian T1 - Metallographische Zielpräparation von Ungänzen im Zusammenspiel mit ZfP-Methoden N2 - Oft sind von außen nicht sichtbare „Ungänzen“ im Innern die Ursache für das Versagen von Bauteilen. In manchen Fällen genügt eine herkömmliche metallographische Präparation, um der Schadensursache auf die Spur zu kommen. In anderen Fällen aber sind die Ungänzen zu klein oder ihre Lage zu ungewiss, um sie mit zufälligen Schnitten zu treffen. Zudem würde man durch Fehlversuche das Bauteil zu stark schädigen und so wertvolle Spuren verlieren sowie die weitere Untersuchbarkeit einschränken. In solchen Fällen ist es im wahrsten Sinn des Wortes zielführend, die Ungänzen mit Hilfe eines räumlich abbildenden ZfP-Verfahrens zu lokalisieren und dann mit den erhaltenen Koordinaten eine metallographische Zielpräparation präzise durchzuführen. Als Methoden kommen z.B. Mikro-Computer-Tomographie (µCT) und Tauch-Ultraschall in Frage. Bauteile können kleine elektronische Komponenten sein, aber auch große Bauteile wie Wellen aus Fahrzeugen oder Anlagen. T2 - Metallographietagung 2016 CY - Berlin, Germany DA - 21.09.2016 KW - Metallographie KW - ZfP KW - Schadensanalyse PY - 2016 AN - OPUS4-38190 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bettge, Dirk A1 - Sturm, Daniel A1 - Goldbeck, Hennig T1 - Metallographische Untersuchungen an gebrochenen Hüftprothesen mit Schaftadapter N2 - Modulare Hüftprothesen können individuell der Anatomie des Patienten angepasst werden und haben dadurch eine positive Auswirkung auf dessen Lebensqualität. Unter Betriebsbelastung sind in der zusätzlichen Konusverbindung zwischen Schaft und Kopfteil Relativbewegungen möglich. Selbst an Titan-Bauteilen bewirken diese durch Verletzung der Passivschicht Reibkorrosion und infolgedessen Spaltkorrosion. Verunreinigungen wie z.B. Knochenrückstände in der Konusverbindung bewirken eine erhöhte Relativbewegung und führen zusätzlich zu einer örtlichen Spannungsüberhöhung durch lokale Pressung. Die an der Mantelfläche des Schafts entstehenden Korrosionsdefekte reduzieren die Schwingfestigkeit des Schafts erheblich, so dass dort Schwingrisse initiiert werden können, welche dann durch die üblichen zyklischen Schwell-Biegebelastungen bis zum Restgewaltbruch wachsen. T2 - Metallographietagung 2016 CY - Berlin, Germany DA - 21.09.2016 KW - Metallographie KW - Fraktographie KW - Schadensanalyse PY - 2016 AN - OPUS4-38191 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rosu, Dana-Maria T1 - The accuracy and reproducibility in thickness determination of thin films using SE N2 - Maintaining a consistent product quality is critical for the thin film industry. Therefore, the development of highly accurate protocols able to detect variations and nonidealities in manufactured thin film devices is essential and helps improve production quality and decrease manufacturing costs. The present work will discuss the accuracy and reproducibility in the determination of the thickness of thin films relevant for optoelectronic industry using spectroscopic ellipsometry, starting with the importance of set-up calibration, the need for very well defined calibration standards suitable for real devices and not least, the importance of accurate data analysis. As ellipsometry is an indirect method and theoretical modelling is needed to obtain the desired information regarding the investigated samples (e.g. thickness, roughness, optical constants), the model uncertainty has to be discussed and taken into account. If for ideal samples consisting of single layers with well-known optical constants the determination of thickness and roughness is straight forward and pretty accurate, for real samples, more complex theoretical models are needed and extracting accurate information regarding the samples can be very challenging. With careful calibration and a multidisciplinary approach, a combined measurement methodology can be developed enabling reliability, comparability, and accuracy. For production-relevant operation, maintaining the ease of use and scalability of ellipsometry as a technique can also be retained. T2 - EOSAM (European Optical Society Annual Meeting) CY - Berlin, Germany DA - 26.09.2016 KW - Spectroscopic ellipsometry KW - Thin films KW - Film thickness determination KW - Uncertainty PY - 2016 AN - OPUS4-38109 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Veliz Montes, Cinthya T1 - Unsubstituted, covalently-linked phthalocyanine-C60 fullerene dyads N2 - Were prepared four unsubstituted Pc - C60 fullerene systems, using two different synthetic strategies, via Prato (1,3 - dipolar cycloaddition) or Bingel reactions. The precursor Pcs 1 and 2 were successfully synthesized by cyclotetramerization reaction between TBDPS - protected and unsubstituted phthalonitriles. The surface studies are currently ongoing. T2 - PcsTT2016 Symposium CY - Elche, Spain DA - 27.01.2016 KW - Fullerene KW - Phthalocyanine PY - 2016 AN - OPUS4-38556 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lüth, Peter T1 - CEQAT-DGHS Ringversuchsprogramm der BAM in Kooperation mit QuoData und PTB N2 - Bei der Bewertung der Verlässlichkeit der im Labor gewonnenen Prüfergebnisse spielen Ringversuche eine entscheidende Rolle. Die Bundesanstalt für Materialforschung und -prüfung (BAM) unterstützt deshalb den weiteren Ausbau des Ringversuchsprogramms des im Jahr 2007 gegründeten Kompetenzzentrums zur Qualitätssicherung für Prüfungen von Gefahrgütern und Gefahrstoffen auf physikalische Gefahren (Centre for quality assurance for testing of dangerous goods and hazardous substances, CEQAT-DGHS). Bei allen bisher untersuchten Prüfmethoden besteht ein Verbesserungsbedarf. Die RV müssen daher zunächst auf die Methodenentwicklung, -verbesserung und -validierung abzielen und nicht auf Leistungstests. T2 - 14. Kolloquium zur chemischen und physikalischen Sicherheitstechnik (BAM-PTB-Kolloquium) CY - Berlin, Germany DA - 14.06.2016 KW - Gefahrgut KW - Gefahrstoff KW - Ringversuch KW - Prüfmethode KW - Validierung KW - Qualitätssicherung PY - 2016 AN - OPUS4-38465 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hemmleb, M. A1 - Bettge, Dirk A1 - Berger, D. A1 - Driehorst, I. T1 - 3D surface reconstruction with segmented BSE detector: New improvements and application for fracture analysis in SEM N2 - Application of 4Q-BSE detector and dedicated software enables 3D surface measurements of fracture samples in SEM. 3D surface measurement is independent from magnification and material invariant. Quantitative height measurements require careful detector adjustment and system calibration. Live 3D view allows a fast assessment of topographical features. In addition to SE and BSE imaging, 3D surface data help to analyse and interpret fracture samples. T2 - European Microscopy Congress 2016 CY - Lyon, France DA - 28.08.2016 KW - Topography KW - SEM KW - 3D analysis KW - Fractography PY - 2016 AN - OPUS4-38456 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schade, U. T1 - Estimation of THz waveforms for material characterization of stratified objects N2 - The poster discusses theoretically and exemplarily the influence of the materials and experimentally selected situation on the shape and size deformation of a detected pulse signal previously reflected on a three layer sheet. T2 - 41st International Conference on Infrared, Millimeter, and Terahertz Waves (IRMMW-THz 2016) CY - Copenhagen, Denmark DA - 25.09.2016 KW - THz spectroscopy KW - Pulse reflection KW - Pulse shape analysis KW - Optical layer model PY - 2016 AN - OPUS4-37639 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Yildirim, Arda T1 - Structure and dynamics of 2,3,6,7,10,11-hexakis[hexyloxy] triphenylene in nanoporous anodic aluminum oxide membranes N2 - Due to their chemical structure, a rigid disk-like aromatic core and flexible alkyl chains attached to the core, discotic liquid crystals (DLCs) can organize and stack themselves into columns in a hexagonal columnar mesophase, a mesophase in between the plastic crystalline and isotropicphase. The overlap of the π orbitals of the aromatic core in the hexagonal columnar mesophase leads to a high charge-carrier mobilitie along the column axis – these columns can be considered as “moleculer nanowires” making liquid crystals a promising class of materials for electronic applications. Previous studies on DLCs showed that the phase behavior of DLCs is susceptible to nano confinement. Here in this study, the thermotropic collective orientational order of 2,3,6,7,10,11 hexakis[hexyloxy] triphenylene (HAT6), a triphenylene based DLC, and the effects of nano confinment on of its phase behavior were investigated by broadband dielectric spectroscopy (BDS) and differential scanning calorimetry (DSC). HAT6 was embedded into nanoporous anodic aluminum oxide membranes by melt infiltration in the isotropic phase under argon atmosphere. The filled membranes have the thickness of 80 µm and the diameter of 15mm and parallel aligned tubular nanopores having the pore diameters of 25, 40, 80 and 180 nm. The filling degree for each sample was checked by thermogravimetric analysis (TGA) in order to ensure complete filling. The bulk HAT6 forms, a hexagonal columnar phase between the isotropic phase above 371 K, and the plastic crystalline phase below 340 K. Unlike the bulk, the confined HAT6 forms two peaks in the heat flow during the plastic crystalline-to-hexagonal columnar phase transition, which might be the evidence of two different phase structures close to the wall and in the pore center. Moreover, the isotropic-to-columnar transition of the confined HAT6 shifts with decreasing pore diameter to lower temperatures. T2 - 9th International Conference on Broadband Dielectric Spectroscopy and its Applications CY - Pisa, Italy DA - 11.09.2016 KW - Discotic liquid crystals PY - 2016 AN - OPUS4-37712 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schilling, Markus T1 - Degradation of PE-HD induced by liquid media - FNCT testing N2 - The Full-Notch Creep Test (FNCT) is widely used to characterize the slow crack growth (SCG) behavior of polyolefin materials in “inert” media as well as effects of environmental stress cracking (ESC) in which the medium has decisive influence on damage mechanism and time to failure tf*. Usually the FNCT is applied as a standardized testing method (ISO 16770) using a few universal liquid media, such as solutions of Arkopal N 100 (detergent). Selected relevant PE-HD materials are investigated also in real media and influences of temperature and geometry of specimen and notch are explicitly addressed. The investigations comprise also the ESC behavior of PE-HD in media that are sorbed to a significant extent – such as Diesel and Biodiesel – based on comparison with samples previously saturated with those media. T2 - PolyDays 2016 CY - Potsdam, Germany DA - 28.09.2016 KW - Sorption KW - Environmental stress cracking KW - Slow crack growth KW - PE-HD KW - FNCT PY - 2016 AN - OPUS4-37716 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Corrosion investigations by using gel-type electrolytes N2 - In the presentation different zinc coatings are presented and investigated. Their naturally formed protective layers are electrochemically characterized and corrosion relevant values are determined by using a gel pad based on polysaccharide. The corrosion relevant values allow the differentiation of various zinc coating systems and can describe the current protective effect provided by the coating. It is shown that gel-type electrolytes influence protective layers and coatings considerably less than corresponding bulk electrolytes. From the results it is evident that gel-type electrolytes represent a viable and promising field in corrosion research.zeige mehr T2 - EUROCORR European Corrosion Congress 2016 CY - Montpellier, France DA - 11.09.216 KW - Corrosion investigations KW - Gel-type electrolytes KW - Zinc coatings PY - 2016 AN - OPUS4-37496 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Plarre, Rüdiger T1 - Invasoren im Kleiderschrank N2 - Die Kleidermotte wird als invasive Art (Neozoon) beschrieben. T2 - Lange Nacht der Wissenschaften, FU Berlin, FB Biologie CY - Berlin, Germany DA - 11.06.16 KW - Kleidermotte KW - Invasive Arten KW - Neozoon PY - 2016 AN - OPUS4-36964 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fontana, Patrick T1 - Beton mit funktionalen Oberflächen N2 - Beton ist als Massenbaustoff vielseitig einsetzbar. Eine der neuesten Entwicklungen ist Ultrahochleistungsbeton (UHPC). Seine besonderen Eigenschaften ermöglichen eine zusätzliche Funktionalisierung der Oberflächen, da annähernd beliebige Mikrostrukturen exakt abgeformt werden können. So lassen sich beispielsweise Fassadenelemente aus UHPC bereits bei ihrer Herstellung im Betonfertigteilwerk mit selbstreinigenden Oberflächen ausrüsten. Eine andere Möglichkeit ist eine Anwendung als Datenspeicher. Wie das Beispiel der Schallplatte aus UHPC zeigt, lassen sich Muster, die hier die Schallinformationen enthalten, exakt von einer Matrize kopieren. T2 - Lange Nacht der Wissenschaften 2016 CY - Berlin, Germany DA - 11.06.2016 KW - UHPC KW - Selbstreinigung KW - Datenträger KW - Betonschallplatte PY - 2016 AN - OPUS4-36948 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bradley, I. A1 - Otremba, Frank A1 - Birk, A. M. A1 - Bisby, L. T1 - Novel equipment for the study of pressure vessel response to fire N2 - Pressurisation of full-containment pressure vessels in fire is known to be driven by thermal stratification. The predominant mode of heat transfer to the contents (convection from the shell to the liquid phase) results in formation of „hot“ boundary layers. Sub-cooled boiling may also be present. The warm layer rises to the surface through buoyancy and bubble flow, increasing the surface of the liquid above that of the bulk temperature, and hence driving a pressure rise. For reliable prediction of the complex effects governing vessel pressurization a three-dimensional numerical model is required. Work is being undertaken on such a model by other institutions in cooperation with this project. T2 - ASME 2016 CY - Phoenix, Arizona, USA DA - 11.11.2016 KW - Vessels KW - Novel equipment PY - 2016 AN - OPUS4-38433 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank A1 - Sklorz, Christian T1 - A new tank design for Hazmat N2 - Initial studies have shown pre-deformed honeycomb structure pressure vessels to have comparable burst pressure to straight steel vessels. It was shown that honeycomp structured tanks have a higher energy absorption than straight steel tanks. Future studies will investigate optimization of the deformed plate, to determine if increased payloads or a reduced wall thickness can be achieved. T2 - ASME 2016 International Mechanical Engineering Congress and Exposition (ICME 2016) CY - Phoenix, Arizona, USA DA - 11.11.2016 KW - Hazmat KW - Tankdesign KW - Honeycomb structure PY - 2016 AN - OPUS4-38399 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schönfelder, Thorsten A1 - Otremba, Frank T1 - Temperature distribution during filling of a composite receptacle N2 - The arrangement of the measuring sensors allowed the capture of air flow induced temperatures and material temperatures on various points of the cylinder body. Four significant temperature levels could be observed: Inside the cylinder (far from the wall, close to the wall), inside the aluminium liner and outer surface. Figure 5 shows the temperature distribution after a regular filling process with a filling time of ten minutes. The temperature sensors T1 - T9 are marked with different colors. The corresponding measurement points are shown in Figure 4. Due to the high thermal conductivity of the aluminum liner the induced temperature peaks are quickly derived. A flow-induced exceeding of the maximum approval temperature is not expected. Regarding the safety assessement the results show that the pressure and temperature profilesmustbe taken into account. T2 - ASME 2016 International Mechanical Engineering Congress and Exposition (IMECE2016) CY - Phoenix, Arizona, USA DA - 11.11.2016 KW - Distribution during filling KW - Type III composite pressure receptacles PY - 2016 AN - OPUS4-38404 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sojref, Regine A1 - Nofz, Marianne T1 - Thin and porous sol-gel alumina coatings on a 9% Cr steel as a protection against high-temperature corrosion in power plants N2 - In order to reduce CO2 emissions fossil fuelled power stations with high combustion efficiency are being developed. The increase of the operating temperature, a common way to improve combustion efficiency, leads to enhanced corrosion of heat exchange steel tubes in the power plants. Within the framework of the European project “Production of Coatings for New Efficient and Clean Coal Power Plant Materials” (POEMA)", high temperature corrosion protection coatings are now under investigation. Thin porous sol-gel alumina films are promising candidate coating materials. Coatings were prepared by applying boehmite sols on grinded steel P92 and subsequent heat treatments at temperatures up to 650 °C. Thus a porous layer of worm-like particles was formed consisting of nano-crystallites and amorphous alumina. A dense interface with satisfying adhesion resulted from diffusion of chromium and iron ions out of the steel into the porous coating. However, the film locally exhibited some cracks caused by steep edges in the grinded steel surface. An appropriate substrate pretreatment should avoid this problem. The protection of the steel relies on the barrier function of the alumina coating and the formation of a dense chromia layer at the steel surface. T2 - ICC6 6th International Congress on Ceramics CY - Dresden, Germany DA - 21.08.2016 KW - High-temperature corrosion KW - Alumina KW - Chromium PY - 2016 AN - OPUS4-38354 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wallau, Wilma T1 - Alkali-Kieselsäure-Reaktion in Beton - Entwicklung eines Prognoseverfahrens N2 - Zur Vermeidung der schädigenden Alkali-Kieselsäure-Reaktion in Betonbauwerken wird die Alkalireaktivität von Gesteinskörnungen im Vorhinein getestet. Der 60°C-Betonversuch ermöglicht eine vergleichsweise schnelle Einschätzung nach fünf-monatiger Testzeit. Dazu wird die Dehnung von Betonprüfkörpern, die mit der zu testenden Gesteinskörnung hergestellt wurden, manuell alle 28 Tage gemessen. Ein alternatives, an der BAM in den vergangen Jahren entwickeltes Verfahren setzt Dehnungssensoren ein, um kontinuierlich und online zu messen. Die Dehnungskurven sind eine gute Grundlage sowohl für die Prognose vom Expansionsverhalten während des Tests als auch für die Validierung von Expansionsmodellen. T2 - 3. Workshop im Themenfeld Material zu den Schwerpunktthemen "Laufende Projekte und neue Aktivitäten" CY - Berlin, Germany DA - 12.10.2016 KW - Baustoffe KW - Alkali-Kieselsäure-Reaktion PY - 2016 AN - OPUS4-40156 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Léonard, Fabien T1 - CT for additive manufacturing process characterisation: assessment of melt strategies on defect population N2 - Selective Electron Beam Melting (SEBM) is a promising powder bed Additive Manufacturing (AM) technique for near net-shape manufacturing of high-value titanium components. However, as with every emerging technique, the manufacturing processes can still be greatly improved and optimised. In particular, the links between AM settings and the resulting sample porosity is of great interest, as the fatigue life of SEBM parts is currently dominated by the presence of porosity. In this study, the size, volume fraction, and spatial distribution of the pores in model samples have been characterised in 3D, using X-ray Computed Tomography (CT), and correlated to the SEBM process variables. A strong relationship was found with the different beam strategies used to contour, and infill by hatching, a part section. The majority of pores were found to be small spherical gas pores, concentrated in the infill hatched region. Rarer irregular shaped pores were mostly located in the contour region and have been attributed to a lack of fusion between powder particles. T2 - Conference on Industrial Computed Tomography iCT2016 CY - Wels, Austria DA - 09.02.2016 KW - Titanium KW - Additive Manufacture KW - Selective Electron Beam Melting KW - Pores KW - Defects KW - X-ray Computed Tomography PY - 2016 AN - OPUS4-39186 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kabelitz, Anke T1 - Time resolved WAXS studies on the crystallization of Al13 keggin clusters N2 - We report on the in situ investigation of the Al13 sulfate synthesis by WAXS. Al13 sulfates were crystallized by precipitating hydrolyzed aluminum solutions by the addition of sodium sulfate. The measurements were performed using an acoustic levitator. The study provides information about the intermediates during the crystallization process. T2 - Eighth Joint BER II and BESSY II User Meeting CY - Berlin, Germany DA - 07.12.2016 KW - In situ KW - Crystallization KW - WAXS PY - 2016 AN - OPUS4-39365 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Becker, Ben T1 - Aging of composite pressure cylinder (COD-AGE) N2 - Subject, Aim and methods within the Project COD-AGE. Test methods and condition monitoring for Composite-cylinders T2 - Follow-up Workshop on statistical safety assessment CY - Berlin, Germany DA - 05.10.2016 KW - Aging KW - Composite cylinder KW - Non destructive testing PY - 2016 AN - OPUS4-39087 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - John, Sebastian T1 - Lebensdauerabschätzung von Composite-Druckgefäßen / COD-AGE N2 - Ermittlung von Kennwerten und Modelbildung zur Lebensdauerabschätzung von Composite-Druckgefäßen. T2 - 3. Workshop Themenfeld Material CY - Berlin, Germany DA - 12.10.2016 KW - Composite-Druckgefäße KW - Lebensdauer KW - FEM KW - Bruchmechanik PY - 2016 AN - OPUS4-39090 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rosemann, Paul T1 - Einfluss der Oberflächennachbearbeitung auf die Korrosionsbeständigkeit von Schweiß-nähten des Duplexstahls 1.4062 N2 - Die Korrosionsbeständigkeit geschweißter Konstruktionen aus nichtrostenden Duplexstählen wird von den Schweißparametern und der Nachbehandlung der Oberflächen bestimmt. Eine etablierte Methode der Schweißnahtnachbehandlung ist das Strahlen der Oberfläche mit Glasperlen. Diese Methode soll aus wirtschaftlichen Gründen durch das Strahlen mit Korund ersetzt werden, welches deutliche Zeit- und Kostenvorteile bietet. Besonders bei der Lochkorrosionsbeständigkeit hat sich das Schleifen mit Korund bereits als nachteilig erwiesen, weshalb diese Umstellung auch beim Stahlen kritisch hinterfragt wird. Daher wurden Probeschweißungen bei der Firma Modersohn hergestellt und mit verschiedenen Oberflächenbearbeitungsmethoden (Glasperlenstrahlen, Korundstrahlen, Beizen, Elektropolieren, Schleifen) nachbehandelt. Diese verschiedenen Oberflächenzustände wurden analytisch (REM, Rauheit) charakterisiert und hinsichtlich ihrer Lochkorrosionsbeständigkeit vergleichend untersucht werden, um die Eignung des Strahlens mit Korund zu beurteilen. T2 - GfKORR-Jahrestagung 'Duplex-Stähle – Nische oder Zukunft ?' CY - Frankfurt/M., Germany DA - 15.11.2016 KW - Korrosionsbeständigkeit KW - Schweißnähte KW - Duplexstahl PY - 2016 AN - OPUS4-39470 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rosemann, Paul A1 - Kauss, Norman T1 - Einfluss des Schwefelgehalts auf die Korrosionsbeständigkeit des nichtrostenden Stahls 1.4404 N2 - Die Korrosionsbeständigkeit nichtrostender Stähle wird maßgeblich von ihrer chemischen Zusammensetzung bestimmt. Der tendenzielle Einfluss ist für die Hauptlegierungselemente in der wissenschaftlichen Fachliteratur beschrieben. Bei Begleitelement Schwefel gibt es dagegen keine konkreten Untersuchungen die belegen, ab welchem Gehalt mit einer Verringerung der Korrosionsbeständigkeit zu rechnen ist. Im Lichtbogenschmelzofen wurden verschiedene Legierungen mit abgestuftem Schwefelgehalten hergestellt, um den Einfluss dieses Begleitelementes auf die Korrosionsbeständigkeit systematisch zu untersuchen. Die KorroPad-Prüfung und die Bestimmung kritischer Lochkorrosionspotentiale wurden zur Charakterisierung der Legierungen genutzt. Beide Methoden belegen eine zunehmende Verringerung der Lochkorrosionsbeständigkeit mit dem Schwefelgehalt. T2 - GfKORR-Jahrestagung 'Duplex-Stähle – Nische oder Zukunft ? CY - Frankfurt/M., Germany DA - 15.11.2016 KW - Schwefelgehalt KW - Korrosionsbeständigkeit KW - Nichtrostender Stahl PY - 2016 AN - OPUS4-39472 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, C. T1 - Einfluss der Abkühlgeschwindigkeit auf die Korrosionsbeständigkeit martensitischer nichtrostender Stähle N2 - Martensitische nichtrostende Stähle werden in verschiedenen technischen Bereichen eingesetzt, bei denen eine optimale Kombination aus hoher mechanischer Festigkeit und guter korrosiver Beständigkeit gefordert wird. Beide Eigenschaften werden in der Industrie primär durch die Wärmebehandlung gesteuert. Die Korrosionseigenschaften sind dabei stark von der diffusionsbedingten Bildung und Auflösung von Chromkarbiden abhängig. In vergangenen wissenschaftlichen Arbeiten konnte nachgewiesen werden, dass die Abkühlgeschwindigkeit nach dem Austenitisieren einen großen Einfluss auf die Bildung solcher Karbide hat. Der Einfluss der Abkühlgeschwindigkeit auf die Lochkorrosionsbeständigkeit wurde an den Stählen 1.4108 und 1.4116 systematisch untersucht. Mit Hilfe des Stirnabschreckversuches wurde dabei die Abkühlgeschwindigkeiten variiert und anschließend die Veränderung von Gefüge, Lochkorrosionsbeständigkeit und Härte untersucht. Als Ergebnis konnten kritische Abkühlgeschwindigkeiten ermittelt werden, bei denen eine kritische Verringerung der Korrosionsbeständigkeit einsetzt. T2 - GfKORR-Jahrestagung 'Duplex-Stähle – Nische oder Zukunft ?' CY - Frankfurt/M., Germany DA - 15.11.2016 KW - Korrosionsbeständigkeit KW - Martensitische nichtrostende Stähle KW - Abkühlgeschwindigkeit PY - 2016 AN - OPUS4-39473 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wu, Cheng-Chieh T1 - Determination of an approximate anisotropic model for a given geometrical complex isotropic structure by means of finite element method and least-squares adjustment N2 - Many engineering structures are made of composite materials or metal foam. To simulate the deformational behaviour of these structures often requires a high number of discretisation elements. This in turn yields a very large system of linear equations that are extremely time and memory consuming or practically impossible to solve. It is therefore desirable to find an approach to overcome this obstacle. T2 - PhD Day 2016 CY - Berlin, Germany DA - 01.09.2016 KW - Least-Squares Adjustment KW - Inverse Analysis KW - Finite Element Method PY - 2016 AN - OPUS4-37521 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wu, Cheng-Chieh T1 - Approximate model for geometrical complex structures N2 - Many engineering structures are made of composite materials or metal foam. To simulate the deformational behaviour of these structures often requires a high number of discretisation elements. This in turn yields a very large system of linear equations that are extremely time and memory consuming or practically impossible to solve. It is therefore desirable to find an approach to overcome this obstacle. T2 - 33rd Danubia- Adria Symposium on Advances in Experimental Mechanics CY - Portorož, Slovenia DA - 20.09.2016 KW - Inverse analysis KW - Finite element method KW - Least-squares adjustment PY - 2016 AN - OPUS4-37523 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Madkour, Sherif T1 - Dielectric investigations on carbon nanomembranes N2 - Multilayer carbon nanomembrances (CNMs) could pave the way for a new ultrathin functional conductive coatings with tunable electrical, optical, and chemical properties. Due to their molecular thickness, they can also be regarded as “interfaces without bulk” separating regions of different gaseous, liquid, or solid components and controlling the materials exchange between them, making them optimal materials for membranes applications. Furthermore, their physical and chemical properties depend strongly on their structure, molecular composition, and the surroundings of either sides, thus allowing for tailored properties. Here, nanolayers of Aromatic p-terphenylthiol (TPT) self-assembled into 2D carbon monolayers (thickness - 1.6 nm) were synthesized and further crosslinked by ion bombardment, forming CNMs. Here, though a recently developed multilayer nanosheets routine, stacks of 5, 10, 15 and 20 TPT sheets where transferred on top of each other forming a multilayered CNMs. However, this transfer routine could introduce some intrinsic defects to the sheets, which would alter the molecular composition and / or structure, thus consequently the CNMs properties. Therefore, it is essential to characterize defects in “pure” TPT nanomembranes, before tailoring the molecular compositions, e.g. adding functional groups. For this reason, broadband dielectric spectroscopy (BDS) was utilized to characterize any defects that could be rasied during preparation. Due the structure of pure TPT membranes, no dipole moment should exsist. However, the presence of other elements, e.g. water or sulphur, would result in a dipole moment that could be probed by BDS. As a main result, for all different stacked-layer numbers, a clear relaxation process is seen, which moves to higher frequencies with increasing the temperature. The temperature dependence of the relaxation rate of this process is independent of film thickness and can be well described by a common VFT function, hence a corporative motion. This relaxation process was assigned to intrinisic defects in the membranes, introduced during preparation, which was further confimed by a detailed anaylsis of the dielectric strength. This is the first BDS measurment on TPT CNMs. T2 - 9th International Conference on Broadband Dielectric Spectroscopy and its Applications CY - Pisa, Italy DA - 11.09.2016 KW - Carbon nanomembranes PY - 2016 AN - OPUS4-37527 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Sebastian Hanns-Otto T1 - Wide-spectrum dielectric functions of ALD deposited oxides relevant for photovoltaics N2 - Silicon surface passivation with atomic layer deposited (ALD) thin films has gained more and more interest in the PV community in recent years. With ALD good film quality, accurate thickness control and conformity are reached. Furthermore, ALD is capable of coating difficult substrates such as nanostructured surfaces with the same accuracy as flat surfaces. A variety of materials such as Al2O3, TiO2 and HfO2 demonstrate good surface passivation quality both for front and rear surface of silicon solar cells. In addition of providing good surface passivation, thin films with high refractive index e.g. HfO2, TiO2 and AlN can act simultaneously as antireflection coatings when applied on the front surface of the device. Hence, ALD thin films can reduce both electrical and reflective losses in solar cells. Thorough investigation of the optical properties of these layers is crucial for several reasons related to their production and use. Optical measurements provide a fast, easy, non-destructive, and in situ capable approach to quality assurance for photovoltaic devices. As the function of the final device is optical, optimisation of the device performance relies strongly on the knowledge of the wide-range dielectric function of the thin layers. In this contribution, we determined the optical constants of ALD generated layers of AlN, Al2O3, TiO2, and HfO2 in a wide spectral range covering the near ultraviolet and the mid-infrared regions by means of spectroscopic ellipsometry. By combining data from a UV-Vis-NIR ellipsometer (Woollam M2000DI) and an FTIR ellipsometer (Sentech Sendira), we can determine the optical constants alongside with the layer thicknesses from one large set of spectroscopic measurements. We consider this a contribution to the metrological treatment of stratified and structured thin films in the optical range by polarisation-sensitive measurement methods. T2 - International conference on spectroscopic ellipsometry (ICSE 7) CY - Berlin, Germany DA - 06.06.2016 KW - ALD (atomic layer deposited) KW - Ellipsometry KW - Photovoltaic KW - Solar Cell KW - HfO2 KW - Aln KW - Al2O3 KW - TiO2 PY - 2016 AN - OPUS4-37222 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kotschate, Daniel T1 - Reference block design for high resolution ultrasound immersion tank N2 - In respect of modern approaches in material sciences and highly increased requirements on materials on safety relevant components, quality management and non-destructive testing reclaims a steadily increased meaning. The destructive meaning of measuring the degree of purity is defined in DIN EN 10247 through metallurgical investigations, especially microsections. For and comparable, but non-destructive testing due ultrasonic testing, the material the SEP 1927 is a well-defined industry standard. A novel and alternative way of reference block construction was focused by this work. The proposed amendments, regarding the manufactoring and machining, are less time and cost consuming. Verified by measurements the presented reference block fits the same acoustical characteristics and the requirements of the guideline. T2 - World Conference on Non-Destructive Testing CY - Munich, Germany DA - 13.06.2016 KW - Immersion tank testing KW - SEP 1927 KW - Degree of purity KW - High resolution ultrasonic testing PY - 2016 AN - OPUS4-36850 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erdmann, Maren T1 - Diesel and biodiesel induced degradation of polyethylene N2 - Renewable resources become more and more relevant to maintain energy demands for an increasing global population. Biosynthetic fuels like biodiesel might replace conventional petrochemical fuels, such as diesel. However, more research is needed to characterize the interaction between the different fuels and the polymeric material, especially with respect to ageing and degradation. The poster will present several interaction and degradation phenomena of high density polyethylene (PE-HD) induced by diesel and biodiesel 1-3. Also the possible influence of microbial growth (fungi and bacteria) is considered. The chosen PE-HDs are typical thermoplastic resins for container and storage tank applications. Degradation of PE-HD will be investigated by changes of the mechanical properties – with main emphasis on the Charpy impact strength 2. Furthermore, with alternating sorption and desorption cycles in combination with oven ageing the co-oxidation 3 of PE-HD in contact with biodiesel will be addressed. T2 - MoDeSt 2016 CY - Cracow, Poland DA - 04.09.2016 KW - Impact strength KW - PE-HD KW - Diesel KW - Biodiesel KW - Degradation PY - 2016 AN - OPUS4-37320 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Duffner, Eric T1 - Hydraulic load cycle test bench for extreme temerature tests N2 - Components, function and technical details of the hydraulic load cycle test bench for extreme temperature test. T2 - Hannover Industrie Fair CY - Hannover, Germany DA - 25.04.2016 KW - extreme temperature KW - life cycle test KW - cylinders PY - 2016 AN - OPUS4-37251 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Duffner, Eric T1 - Hydraulic slow burst test bench N2 - Components, function and technical details of the Hydraulic slow burst test bench T2 - Hannover Industrie Fair CY - Hannover, Germany DA - 25.04.2016 KW - cylinders KW - burst test KW - creep behaviour PY - 2016 AN - OPUS4-37252 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Konnertz, Nora T1 - QCM System for the Characterization of Gas Sorption and Physical Aging of Membrane Polymers for Gas Separation Applications N2 - Polymers are favorable materials for gas separation membranes. In general, gas transport experiments are performed with films in the range of 100 µm thickness. However, in large-scale processes very thin selective polymer layers in the range of 100 nm to 1 µm are used. Moreover, it was shown that thin films behave different compared to thick films with respect to gas transport properties and physical aging as well. Thus, for fundamental research it is important to realize gas transport experiments with thin films. The Quartz Crystal Microbalance (QCM) is a very sensitive method to detect mass changes in the range of nanograms. Therefore, this method enables sorption experiments with thin films or layers attached to the QCM crystal (100 nm up to 1 µm). Here, we present the experimental set-up for using the QCM technique for characterizing the gas sorption behavior of thin polymer films in a temperature controlled pressurized environment (up to 50 bar) - also quartz crystals and crystal holders were optimized. The study aims for the characterization of long-term behavior and physical aging of high-performance polymers for gas separation membranes - such as polyimides and polymers of intrinsic microporosity (PIMs) and respective nanocomposites. Especially the differences of the behavior of thin films compared to films with thicknesses up to 100 µm as well as nanofiller induced-effects are adressed. T2 - Polydays 2016 CY - Potsdam, Germany DA - 28.09.2016 KW - Quartz Crystal Microbalance QCM KW - Thin Films; KW - Gas Sorption KW - High Pressure PY - 2016 AN - OPUS4-37911 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sieber, Sarah T1 - Image denoising of ultrasonic echo data acquired on concrete N2 - Ultrasonic echo testing has become a common method in civil engineering for the investigation of concrete structures. The detection of inhomogeneities, reinforcing elements and the geometry of the object is required for quality assurance and Inspection. This assessment depends on the quality of ultrasonic images which can be improved by using Reverse Time Migration (RTM) rather than the standard method, Synthetic Aperture Focusing Technique (SAFT). Although RTM provides a better mapping of circular objects and (dipping) reflectors, the image is corrupted by migration noise. To suppress the image noise, we have tested various filter methods in the spatial domain, frequency domain as well as in the curvelet domain on ultrasonic RTM images. We found that either a spatial edge detection filter in combination with a lowpass filter (Laplacian of Gaussian filter) or two lowpass filter with different filter parameters (Difference of Gaussian filter) removed artefacts. An additional smoothing was obtained by applying the first generation curvelet transform after downsampling the image matrix and adding Gaussian noise. The proposed filter scheme is able to suppress RTM noise and enhance the image quality such that the objective interpretation of ultrasonic images for Quality assessment of concrete specimen is simplified. T2 - 76. Jahrestagung der Deutschen Geophysikalischen Gesellschaft CY - Münster, Germany DA - 14.03.2016 KW - Ultrasonic echo technique KW - Reverse-time migration KW - Image Denoising KW - Curvelet Transform PY - 2016 AN - OPUS4-35839 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Munzke, Dorit T1 - Zustandsüberwachung von Composite-Druckgefäßen mit faseroptischer Sensorik N2 - Funktionsweise, Integration und Messergebnisse von opt. Fasern zur Zustandsüberwachung von Composite-Druckgefäßen. T2 - 3. Workshop Themenfeld Material CY - Berlin, Germany DA - 12.10.2016 KW - Faseroptik KW - Zustandsüberwachung KW - Composite-Druckgefäße PY - 2016 AN - OPUS4-39097 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Ralf T1 - High-temperature laser profilometry N2 - Advanced methods for 3D green density characterization like computed tomography and 3D FE sinter modeling can be utilized for increasing the reliability of sintered components. The experimental in situ observation of sintering, however, is currently restricted to silhouette methods, i.e. heating microscopy. For complex shaped samples, in situ shape screening during shrinkage would allow much better validation of 3D sinter simulation models. Further, by revealing temporary sinter warpage, 3D high-temperature shape screening allows to locate potential defects of complex sintered components. Against this background, BAM developed a testing device for in situ 3D high-temperature shape screening for ceramic and glass-ceramic tapes up to 1000°C [1-3]. Current work is focused on dropping this restriction in sample shape and temperature. The poster illustrates the current state of this work and possible applications of the method e.g. in detecting sinter warpage of metallized glass-ceramic LTCC tapes. T2 - SGT Centenary Conference, & ESG 2016 CY - Sheffield, UK DA - 04. 09. 2016 KW - Laser profilometry KW - 3D High-temperature shape screening KW - Sintering PY - 2016 AN - OPUS4-38320 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Konnertz, Nora T1 - Enhanced gas separation performance of nanocomposites based on a polymer with intrinsic microporosity PIM-1 and phenethyl-POSS N2 - In times of the energy revolution, the need for energy efficient separation processes promotes the advancement of new high performance materials for use as highly selective separation membranes. Most promising materials in this field, especially for gas separation, are polymers with intrinsic microporosity (PIMs) which were firstly introduced by Budd and McKeown. In this study the permeability of PIM-1 was increased by 439 % by formation of nanocomposites with only 1 wt% of polyhedral oligomeric phenethyl-silsesquioxane (PhE-POSS) within the polymer matrix. As the CO2/CH4 selectivity is fully retained, this leads to a shift in the Robeson plot towards the upper bound. The Robeson plot describes the current state of the art trade-off relation between selectivity and permeability of all known membrane polymers. As molecular mobility is a key factor for gas transport as well as the often observed physical aging of such polymers, our study also includes for the first time, molecular dynamics and conductivity of pure PIM-1 and PIM-1 nanocomposites as investigated by broadband dielectric spectroscopy (BDS). T2 - Polydays 2016 CY - Potsdam, Germany DA - 28.09.2016 KW - PIM-1 KW - POSS KW - Broadband dielectric spectroscopy KW - Permeation PY - 2016 AN - OPUS4-37701 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weise, Frank T1 - Influence of aggregate size on the damage potential of alkal-silica-reaction N2 - The poster shows new results on Alkali-Silica-Reaction (a damage mechanism of concrete). The influence of the aggregate size in the sand fraction is investigated, revealing that different types of aggregate behave in a different way. T2 - 15th International Conference of Alkali Aggregate Reaction in Concrete (ICAAR 2016) CY - Sao Paulo, Brazil DA - 03.07.2016 KW - Alkali-silica-reaction KW - Building materials KW - Concrete KW - Durability PY - 2016 AN - OPUS4-36951 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Epperlein, Nadja T1 - Influence of femtosecond laser produced nanostructures on biofilm growth on steel N2 - Large area periodic surface structures were generated on steel surfaces using 30-fs laser pulses at 790 nm wavelength. Two types of steel exhibiting a different corrosion resistance were used, i.e. a plain structural steel (corrodible) and a stainless steel (resistant to corrosion). Homogeneous fields of laser-induced periodic surface structures (LIPSS) were realized utilizing laser fluences close to the ablation threshold while scanning the sample under the focused laser beam in a multi-pulse regime. The nanostructures were characterized with optical and scanning electron microscopy. For each type of steel, more than ten dentical samples were laser-processed. These samples were subjected to microbial adhesion tests, investigating bacterial adhesion behavior on the laser structures in comparison to polished reference surfaces. Short term experiments (<24h) were carried out to determine initial biofilm development. E. coli as a typical bacterium representing pathogenic bacteria and Shewanella putrefaciens as metal corrosive bacterium were used for biofilm development analyses. Bacterial cell adhesion was determined microscopically after DAPI cell staining (DNA staining). Comparison of the coverage areas between nanostructured and polished surfaces revealed differences in cell adhesion behavior and biofilm structure. T2 - E-MRS 2016 Spring Meeting, Symposium C: "Laser-material interactions for tailoring future applications" CY - Lille, France DA - 02.05.2016 KW - Laser-induced periodic surface structures (LIPSS) KW - Femtosecond laser ablation KW - Biofilms KW - Steel PY - 2016 AN - OPUS4-36045 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weltschev, Margit T1 - Comparison of the environmental stress cracking behaviour of polyethylene and polyethylene terephthalate as materials for dangerous goods packagings N2 - The chemical industry has expressed great interest in using polyethylene terephthalate (PET) as material for packagings for the transport of dangerous goods. Due to the high strength and stiffness of PET, the wall thickness and weight of packagings can be reduced. This is a relevant cost factor. PET is a semi-crystalline thermoplast which is produced by polycondensation of terephthalic acid and ethylene glycol. According to the European dangerous goods regulations RID and ADR, samples of PET design types of packagings for dangerous goods must be pre-stored with the original filling good for six months at 23°C, before the design type tests can be carried out. For packagings made of polyethylene (PE) tests to prove the stress cracking resistance by using laboratory methods are possible to reduce time and costs. Therefore, standard liquids, simulating the different types of damaging effects on PE are defined in RID and ADR. However, there is no information and research available about the damaging mechanisms on PET in comparison to PE, especially regarding to stress cracking resistance and test methods. The aim of this work is to compare the stress cracking resistance of PE and PET with the Full Notch Creep Test (FNCT), which was developed by chemical industry and is described in the standards EN ISO 16101 and EN 15507. It was investigated whether testing specimens made of PE and PET with a full coplanar notch around the middle of the specimens show weakening after the impact of a tensile force in a wetting solution (Lutensol® FSA 10) at 50°C in a test device on the basis of the FNCT. The test results confirmed the suitability of the method for eight PE grades. Unfortunately, this method couldn’t be used for PET because the specimens broke during notching. In addition the molding of the sheets and the following temper process for twelve hours are very time-consuming, and the specimens broke during notching due to the high brittleness of PET. Another possibility to provide evidence of stress cracking resistance of PE packagings is laid down in BAM’s Dangerous Goods Rule BAM-GGR 015. This test was carried out with PE and PET bottles to compare both materials. Therefore 1l test bottles were filled with a 5% wetting solution and mounted with a clamping tool for 28 days at 40°C. Tensile test specimens were cut out afterwards from the middle of the bottles in the deformed areas. Tensile strength and breaking elongation of PE specimens were determined in comparison to the PET specimens. The tensile properties of the PET specimens couldn’t be determined due to the strength and the stiffness of the material. In conclusion the only way to provide information about the stress cracking resistance of PET was to perform stacking tests. 1l bottles made of PE and PET were filled with a 5% wetting solution and stored with a stacking load for 28 days at 40°C according to EN ISO 16495. Design types of PE and PET both passed the stacking tests. T2 - EUROCORR 2016 CY - Montpellier, France DA - 11.09.2016 KW - polyethylene terephthalate KW - stress cracking resistance KW - test methods KW - dangerous goods packagings PY - 2016 AN - OPUS4-37448 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erdmann, Maren T1 - Mechanical characterization of high-density polyethylene in contact with diesel and biodiesel fuels N2 - Renewable resources become more and more relevant to maintain energy demands for an increasing global population. Biosynthetic fuels like biodiesel might replace conventional petrochemical fuels, such as diesel. However, more research is needed to characterize the interaction between the different fuels and polymeric materials widely used in the fuel infrastructure as well as for automotive parts. Especially changes in the structural properties and mechanical behavior of the polyethylene (PE-HD) have to be addressed. The presented work comprises the direct interaction of high density polyethylene (PE-HD) with diesel and biodiesel, resulting in swelling and plasticization. Also long-term degradation phenomena will be discussed. The chosen PE-HD types are typical thermoplastic resins for container and storage tank applications. The impact of diesel and biodiesel in PE-HD is investigated by changes in the mechanical properties with emphasis on the Charpy impact strength. Furthermore, structural and dynamic influences on the polymeric material induced by diesel and biodiesel are proven in Dynamic Mechanical Analysis (DMA). Both methods, Charpy impact strength and DMA, reveal softening effects due to the migration of diesel and biodiesel into the amorphous regions of PE-HD. Since biodiesel is more prone to oxidative degradation compared to diesel, the fuel/air/polymer-interaction is studied for partly immersed tensile test specimens. Main focus of the evaluation is the co-oxidation. Here, the accelerated deterioration of PE caused by the sorption of the facile oxidation of biodiesel into the solid polymer might be a major degradation mechanism in this context. T2 - POLYDAYS 2016 CY - Potsdam, Germany DA - 28.09.2016 KW - PE-HD KW - Diesel KW - Biodiesel KW - Oxidation PY - 2016 AN - OPUS4-37677 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scheuerlein, T1 - Mechanical properties of the HL-LHC 11 Tesla Nb3Sn magnet constituent materials N2 - A test campaign was launched to determine the mechanical properties of the HL-LHC 11 T Nb3Sn magnet components in order to accurately model the mechanical properties in Finite Element simulations that predict the stress and strain distribution in These magnets. Static and dynamic test methods have been applied for determining elastic materials behavior, and highly accurate Young’s moduli are obtained with the dynamic methods resonance and impulse excitation. These non-destructive methods also enable temperature dependent modulus measurements during in situ heat cycles. T2 - Applied Superconductivity Conference CY - Denver, Colorado, USA DA - 04.09.2016 KW - Young's modulus KW - Tensile test KW - Resonanz KW - Impact excitation PY - 2016 AN - OPUS4-37414 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scheuerlein, C. T1 - Mechanical properties of the HL-LHC 11 Tesla Nb3Sn magnet constituent materials N2 - A test campaign was launched to determine the mechanical properties of the HL-LHC 11 T Nb₃Sn magnet components in order to accurately model the mechanical properties in Finite Element simulations that predict the stress and strain distribution in these magnets. Static and dynamic test methods have been applied for determining elastic materials behavior, and highly accurate Young’s moduli are obtained with the dynamic methods resonance and impulse excitation. These non-destructive methods also enable temperature dependent modulus measurements during in situ heat cycles. T2 - Applied Superconductivity Conference CY - Denver, USA DA - 04.09.2016 KW - Young´s modulus KW - Tensile KW - Compression KW - Temperature dependence PY - 2016 AN - OPUS4-37922 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mull, Birte T1 - Development of a reproducibly emitting reference material for volatile organic compounds N2 - Volatile organic compounds (VOC) are ubiquitous in the indoor air, since they emit from materials used indoors. Investigations of these materials are mostly carried out in test chambers under controlled climatic conditions. Quality control of these test chamber measurements is important but there is a lack of commercially available homogenous reference materials. The approach of this study is to dope a supporting material with VOCs, which are then reproducibly released in measurable chamber air concentrations between 30 to 300 µg m ³. From several tested supporting materials vacuum grease (APIEZON M) was selected because of its very low own emissions. First tests were conducted with styrene. For the estimation of the initial emission and the emission over time FEM (finite element methods) modelling was used. Based on this, five samples with a surface of 7 cm2 and a thickness of 12 mm with a content of 1 ‰ styrene were investigated at (23 ± 2) °C and (50 ± 5) % relative humidity in the µ-chamber (3 samples) and 24 L test chambers (2 samples) for 28 days. Air samples were taken after 24 hours, 3, 7, 14, 21 and 28 days on Tenax TA® sorption tubes and analyzed by TD-GC-MS. The area specific emission rate (SERa) was calculated to compare the results from both chamber types. After 24 hours SERa was between 0.8 0.9 µg cm 2 h 1 (3800 4000 µg m 3) for the µ-chamber samples and between 0.9 1.1 µg cm 2 h 1 (300-370 µg m 3) for the 24 L test chamber samples. After 28 days the SERa was at 0.2 µg cm 2 h 1 for all samples. The relative standard deviation of the SERa was between 1 26 %. These results show the applicability of vacuum grease as supporting material and the favored starting concentration range could be achieved in the 24 L test chambers. T2 - Indoor Air 2016, the 14th international conference of Indoor Air Quality and Climate CY - Ghent, Belgium DA - 03.07.2016 KW - Emission test chamber KW - Indoor air KW - Quality assurance KW - Quality control PY - 2016 AN - OPUS4-36823 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Becker, Ben T1 - Zustandsüberwachung von Composite-Druckgefäßen mit faseroptischer Sensorik N2 - Einsatz der Faseroptik zur Zustandsüberwachung von Composite-Druckgefäßen. Aufbau, Integration, Messergebnisse. T2 - Follow-up Workshop on Statistical Safety Assessment of Composite Cylinders CY - Berlin, Germany DA - 05.10.2016 KW - Faseroptik KW - Zustandsüberwachung KW - Composite-Druckgefäße PY - 2016 AN - OPUS4-39088 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Marzok, Ulrich T1 - Bestimmung der H2-Permeabilität von Gläsern mit der VHE-Methode N2 - Die Entwicklung von Wasserstoffbarrieren aus Glas erfordert die genaue Messung geringster H2-Permeabililtäten. Bisherige Untersuchungen haben gezeigt, dass die VHE-Pulvermethode diesbezüglich eine besonders hohe Empfindlichkeit bietet. Hierbei wird die isotherme Gasabgabe aus sphärischen Partikeln im Rahmen klassischer Diffusionsmodelle gefittet und daraus der Diffusionskoeffizient bestimmt. Für die Untersuchung von Gläsern mit möglichst geringer H2-Permeabilität ist jedoch eine Validierung der Genauigkeit der Methode notwendig. Vor diesem Hintergrund erfolgte die numerische Modellierung der H2-Abgabe mit Hilfe des Programms COMSOL Multiphysics®. Im Poster wird der Einfluss der Korngrößenverteilung der Glaspulverpartikel, der Partikelform sowie der Effekt einer nichthomogenen H2-Startverteilung auf die mittels Pulvermethode ermittelten Diffusionskoeffizienten diskutiert. T2 - 90. Glastechnische Tagung (Deutsche Glastechnische Gesellschaft e.V.) CY - Goslar, Germany DA - 06.06.2016 KW - Wasserstoffpermeation KW - Glas KW - Vakuumheißextraktion KW - Pulvermethode KW - Simulation PY - 2016 AN - OPUS4-36528 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Welter, T. T1 - Glasstrukturen mit geringer Helium- und Wasserstoffpermeation N2 - Wasserstoffbarrieren aus Glas erfahren zunehmend Bedeutung als Werkstoff in der Energietechnik. Trotz wachsender Anwendungen liegen überwiegend empirisch gewonnene Beziehungen zwischen Glaszusammensetzung und Wasserstoffpermeation vor, die im wesentlichen aus dem Verhalten von Kieselglas abgeleitet werden. In dieser Studie werden daher topologische Parameter der Glasstruktur identifiziert und mit thermodynamischen Parametern korreliert. Auf der Seite der Glastopologie steht das freie Volumen und der Vernetzungsgrad des Netzwerkes während auf der thermodynamischen Seite die Konfigurationsentropie bzw. die Konfigurationswärmekapazität Aufschluss über die Verteilung des freien Volumens geben kann. Dabei wird angenommen, dass für Temperaturen weit unterhalb der Glasübergangstemperatur die chemische Löslichkeit von H2 zu vernachlässigen ist. Um die eingeschränkte Datenlage für die Wasserstoffpermeation kompositionell zu erweitern, wurden zusätzlich Heliumpermeationsmessungen ausgewertet. Die Ergebnisse zeigen, dass für Silicatgläser ein charkteristisches Verhältnis von freiem Volumen zu Netzwerkaufspaltung herrschen muss, um permeationsstabile Gläser zu erhalten. T2 - 90. Glastechnische Tagung CY - Goslar, Germany DA - 06.06.2016 KW - Glasstruktur KW - Helium- und Wasserstoffpermeation KW - Alkalialumosilicatsysteme KW - Thermodynamik KW - Energietechnik PY - 2016 AN - OPUS4-36583 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Marzok, Ulrich T1 - High-temperature laser profilometry N2 - Advanced methods for 3D green density characterization like computed tomography and 3D FE sinter modeling can be utilized for increasing the reliability of sintered components. The experimental in situ observation of sin-tering, however, is currently restricted to silhouette methods, i.e. heating microscopy. For complex shaped sam-ples, in situ shape screening during shrinkage would allow better validation of 3D sinter simulation models. Further, by revealing temporary sinter warpage, 3D high-temperature shape screening would allow to locate potential defects of complex sintered components. Against this background, BAM developed a testing device for in situ 3D high-temperature shape screening for ceramic and glass-ceramic tapes up to 1000°C [1-3]. Current work is focused on dropping this restriction in sample shape and temperature. The poster illustrates the current state of this work and possible applications of the method e.g. in detecting sinter warpage of metallized glass-ceramic LTCC tapes. T2 - 90. Glastechnische Tagung (Deutsche Glastechnische Gesellschaft e.V.) CY - Goslar, Germany DA - 06.06.2016 KW - Laser profilometry KW - 3D High-temperature shape screening KW - Sintering PY - 2016 AN - OPUS4-36510 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Marzok, Ulrich T1 - High-temperature laser profilometry N2 - Advanced methods for 3D green density characterization like computed tomography and 3D FE sinter modeling can be utilized for increasing the reliability of sintered components. The experimental in situ observation of sintering, however, is currently restricted to silhouette methods, i.e. heating microscopy. For complex shaped samples, in situ shape screening during shrinkage would allow much better validation of 3D sinter simulation models. Further, by revealing temporary sinter warpage, 3D high-temperature shape screening would allow to locate potential defects of complex sintered components. Against this background, BAM developed a testing device for in situ 3D high-temperature shape screening for ceramic and glass-ceramic tapes up to 1000°C. Current work is focused on dropping this restriction in sample shape and temperature. The poster illustrates the current state of this work and possible applications of the method e.g. in detecting sinter warpage of metallized glass-ceramic LTCC tapes. T2 - ICC6, 6th International Congress on Ceramics CY - Dresden, Germany DA - 21.08.2016 KW - Laser profilometry KW - 3D High-temperature shape screening KW - Sintering PY - 2016 AN - OPUS4-37708 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Blaeß, Carsten T1 - Sintering and crystallization of new bioactive glasses N2 - Bioglass® 45S5 is mainly used clinically as powders, granules or pastes instead of sintered compacts. This is due to the inherent problem of crystallization during the sintering, which results in poor mechanical properties and reduced bioactivity. Recently, new bioactive glasses with improved crystallization stability have been developed as promising candidates for manufacturing of sintered powder compacts for bone regeneration, which combine improved sintering behavior with bioactivity. Compared with the well-known Bioglass® 45S5 (SiO2-P2O5-CaO-Na2O) the calcium/alkali oxide ratio was increased, sodium oxide was partially replaced by potassium oxide and up to 3 mol% calcium fluoride were added, in order to stabilize the glass against crystallization. The aim of this study was to investigate the sintering and crystallization behavior of these new bioactive glasses. Sintering and crystallization were characterized by heating microscopy, XRD, FTIR, SEM, and DTA. The results show that a sintered density of 88-99 % is achieved in contrast to only 57-67% for Bioglass® 45S5. In addition, FTIR and XRD analyses show that Bioglass® 45S5 crystallized during sintering while for the new glasses no crystalline phases are detected. The thermal properties of all glasses were studied by DTA measurements, and the influence of grain size was characterized. These studies showed that full densification can be attained for particle size < 32 µm, whereas coarser particles progressively increase residual porosity. Observed foaming phenomena, are strongly retarded by crystallization of beta-HAp. T2 - SGT Centenary Conference CY - Sheffield, UK DA - 04.09.2016 KW - Bioactive KW - Glass KW - Crystallization KW - Sintering PY - 2016 AN - OPUS4-38317 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Blaeß, Carsten T1 - Sintering and crystallization of new bioactive glasses N2 - Bioglass® 45S5 is mainly used clinically as powders, granules or pastes instead of sintered compacts. This is due to the inherent problem of crystallization during sintering. Recently, new bioactive glasses with improved crys-tallization stability have been developed as promising candidates for manufacturing of sintered powder compacts for bone regeneration, which combine improved sintering behavior with bioactivity. Compared with the well-known Bioglass® 45S5 (SiO2-P2O5-CaO-Na2O) the calcium/alkali oxide ratio was increased, sodium oxide was partially replaced by potassium oxide and up to 3 mol% calcium fluoride were added, in order to stabilize the glass against crystallization. Sintering and crystallization were characterized by heating microscopy, XRD, FTIR, SEM, and DTA. The results show that a sintered density of 88-99 % is achieved in contrast to only 57-67% for Bioglass® 45S5. Whereas Bioglass® 45S5 powder compacts crystallize during sintering, for the new glasses no crystalline phases were detected. Additionally the influence of grain size was characterized. These studies showed that full densification can be attained for particle size < 32 µm, whereas coarser particles pro-gressively increase residual porosity. Observed foaming phenomena, are strongly retarded by crystallization. T2 - 90. Glastechnische Tagung (Deutsche Glastechnische Gesellschaft e.V.) CY - Goslar, Germany DA - 06.06.2016 KW - Bioactive KW - Glass KW - Crystallization KW - Sintering PY - 2016 AN - OPUS4-38311 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Laquai, René A1 - Müller, Bernd R. A1 - Kupsch, Andreas T1 - Characterizing damage evolution in metal matrix composites with X-ray refraction topography and in situ tensile loading N2 - In this study a metal-matrix-composite with aluminum matrix and Al2O3 particles was investigated with x-ray refraction topography and in-situ tensile loading. It could be observed that after reaching a certain load the specific surface increased steadily. However, the classical radiographs taken for comparison show no damage in the sample. T2 - 8th Joint BER II and BESSY II User Meeting CY - Berlin, Germany DA - 07.12.2016 KW - X-ray refraction KW - Metal matrix composites KW - In-situ loading KW - Synchrotron PY - 2016 AN - OPUS4-39113 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wagner, Sabine T1 - Integration of microspheres coated with fluorescent molecularly imprinted polymers with a fiber optic array for the detection of antibiotics N2 - The widespread use of antibiotics in livestock farming leads to trace residues in food products and wastewater, potentially entailing antimicrobial resistance in food-borne pathogens. The determination of antibiotics in aqueous environments and foodstuff is thus of major concern. Analytical assays based on molecularly imprinted polymers (MIPs) have emerged as a valuable tool in this field due to the low production costs, stability, format adaptability and the possibility to imprint and thus their ability to recognize a wide variety of target analytes. With regard to optical sensing technologies, however, MIPs have only been used in considerably few applications, especially in fluorescence sensors. This limitation is basically due to the fact that the incorporation of a fluorescently responding moiety into a polymer matrix is challenging. One way to overcome this limitation is to use tailor-made fluorescent indicator monomers for direct transfer of the binding event into an optical signal. If such a monomer is integrated into a thin MIP-shell on microspheres such core/shell particles can be readily used in advanced multiplexing sensory fiber-optic microarrays. Here, we propose such a fiber-optic microarray based on fluorescent MIP microspheres for antibiotics. The binding behavior and the selectivity of a microarray using these MIP were examined and compared with a non-imprinted polymer (NIP) control, employing the target molecules and other structurally closely related antibiotics. T2 - Europt(r)ode XIII CY - Graz, Austria DA - 20.03.2016 KW - Molecularly imprinted polymers KW - Fiber-optic microarray KW - Fluorescence PY - 2016 AN - OPUS4-37294 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rizzo, F. T1 - Evaluation of nano-sized internal oxidation in a Fe-13Cr alloy exposed to water vapor atmosphere N2 - The topotactic formation of nano-sized precipitates immediately under the internal oxide layer in a Fe-13Cr alloy exposed to oxidizing water vapor atmosphere was recently reported. The precipitates were identified as lath-shaped Fe-Cr spinel exhibiting a crystallographic orientation relationship with the ferritic matrix. The authors proposed that these precipitates could act as a precursor to the formation of the spinel layer observed in the adjacent part of the oxide scale.The occurrence of internal oxidation in Fe–Cr alloys subjected to similar conditions had been previously identified and directly correlated to the presence of water vapor. In the present work, we attempt to rationalize the processes occurring during the oxidation of this alloy through thermodynamic and kinetic analyses based on the CALPHAD approach, using the geometrical representation of phase equilibria and concepts developed to describe internal oxidation. The influence of water vapor on the mechanism and kinetics of formation of the nano-sized precipitates and its role in the overall oxidation process is also considered. T2 - CALPHAD XLV The forty-fifth International Conference on CALPHAD (Computer Coupling of Phase Diagrams and Thermochemistry) CY - Awaji Island, Hyogo, Japan DA - 29.05.2016 KW - Precipitation KW - Internal oxidation KW - CALPHAD KW - Topotactic transformation KW - Microscopy PY - 2016 AN - OPUS4-42156 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weigert, Florian T1 - Photoluminescence Properties of coreshell CdSe Nanocrystals with Different Shells and Surface Chemistries Derived from Ensemble and Single Particle Measurements N2 - The optical properties of semiconductor nanocrystals (SCNCs) depend on constituent material, particle size, and surface chemistry, with the size of the photoluminescence (PL) quantum yield (QY) and the PL decay kinetics being largely controlled by the number of dangling bonds, which have to be properly passivated for high quality materials. Hence, PL measurements can provide insight not only in SCNC photophysics, yet can be also used for quality control of SCNC synthesis and surface modification. In this respect, steady state and time-resolved fluorometry and confocal microscopy with time correlated single photon counting were used to study the PL properties of core-shell CdSe SCNCs with different shells and surface chemistries on ensemble and single particle level, thereby focusing on a correlation of ensemble PL QY and PL decay kinetics with particle brightness, PL time traces, and the On-time fraction of single SCNCs. Additionally, confocal PL images were correlated with AFM measurements in order to derive the amount of absorbing, yet non-emissive ”dark” SCNCs, the presence of which resulting in an underestimation of ensemble PL quantum yields. The results of this study can help to identify synthetic routes and surface modifications, which minimize the fraction of dark SCNCs. T2 - PicoQuant 22nd International Workshop on Single Molecule and Super-Resolution Microscopy in the Life Sciences CY - Berlin, Germany DA - 14.09.2016 KW - Single molecule KW - SCNC KW - QY KW - AFM KW - Confocal PY - 2016 AN - OPUS4-38121 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Harald Rune T1 - Imaging of local pH in biofilm using polymeric sensors: towards the elucidation of microbial induced corrosion N2 - Microbial induced corrosion (MIC) is a crucial problem in many technical plants as well as fuel tanks, leading to considerable damage and huge financial losses. Successful prevention of MIC requires the localization of first signs of corrosion as well as the identification of factors influencing the corrosion process. In this respect, also the determination of corrosion rates can be of interest for the possible prevention of MIC. Hence, there is a growing need for sensitive and preferably inexpensive tools that enable the early detection of MIC. Of special interest are methods, which provide spatially and time-resolved information and allow the study of changes on metal surfaces as prerequisites for a more detailed analysis of ongoing corrosion processes at a MIC-affected site. Biofilm formation can lead to changes in pH, oxygen and chloride concentration as well as to the release of certain metal ions like Fe(II) and Mn(II) depending on the type of metal surface involved. Hence, optical methods enabling the detection of these analytes at very low concentration and monitoring of their changes can be used for MIC detection. Here, we propose to utilize polymeric nanosensors for MIC detection via the determination of the local pH value changes in different biofilms. Such nanosensors are known to have several advantages in imaging applications such as intracellular pH measurements including the ease of doping or labeling with a multitude of analyte-responsive and inert dye molecules for the realization of a high analyte sensitivity and ratiometric sensing. Moreover, they can be surface functionalized with target-specific ligands e.g., lectins, for the specific binding to the outer surface of certain types of bacteria. In this respect, different polymer architectures will be studied to identify an optimal candidate in terms of imaging performance in conjunction with several classes of pH-responsive fluorescent dyes like cyanines, aza-BODIPYs, and xanthenes, utilizing different mechanism of signal generation such as photo-induced electron transfer or protonation-induced changes in the spectral position of absorption and emission spectra. T2 - Europtrode CY - Graz, Austria DA - 20.03.2016 KW - Nanosensor KW - Microbial induced corrosion KW - Imaging KW - Nanosensor KW - Mikrobiell induzierte Korrosion KW - Bildgebung PY - 2016 AN - OPUS4-35628 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weigert, Florian T1 - Ensemble and single particle studies of the fluorescence properties of core­shell CdSe nanocrystals with different shells and surface chemistries N2 - The optical properties of semiconductor nanocrystals (SCNC) are controlled by constituent material, particle size, and surface chemistry, specifically the number of dangling bonds favoring nonradiative deactivation, and hence also by particle synthesis. In this respect, the fluorescence properties of coreshell CdSe SCNCs with different shells and surface chemistries were studied on ensemble and single particle level, using steady state and timeresolved fluorometry and confocal microscopy with time correlated single photon counting detection. Special emphasis was dedicated to correlate ensemble photoluminescence (PL) quantum yields and decay kinetics with particle brightness, PL time traces, and the Ontime fraction of the single SCNCs. Additionally, the confocal PL images were correlated with AFM measurements in order to derive the amount of absorbing, yet nonemisssive ”dark” SCNCs, the presence of which leading to an underestimation of ensemble PL quantum yields. The results of this study can help to identify synthetic routes and surface modifications minimizing the fraction of dark SCNC, thereby closing the gap to the ultimate goal of colloidally and photochemically stable SCNCs with a PL quantum yield of close to unity. T2 - FQDots16 CY - Berlin, Germany DA - 05.09.2016 KW - Confocal KW - QY KW - QD KW - SCNC KW - Single molecule KW - AFM PY - 2016 AN - OPUS4-38119 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -