TY - CONF A1 - Mull, Birte A1 - Sauerwald, T. A1 - Richter, Matthias A1 - Horn, Wolfgang A1 - Brödner, Doris A1 - Schultealbert, C. T1 - Development of a reproducibly emitting reference material for volatile organic compounds N2 - Volatile organic compounds (VOC) are ubiquitous in the indoor air, since they emit from materials used indoors. Investigations of these materials are mostly carried out in test chambers under controlled climatic conditions. Quality control of these test chamber measurements is important but there is a lack of commercially available homogenous reference materials. The approach of this study is to dope a supporting material with VOCs, which are then reproducibly released in measurable chamber air concentrations between 30 to 300 µg m ³. From several tested supporting materials vacuum grease (APIEZON M) was selected because of its very low own emissions. First tests were conducted with styrene. For the estimation of the initial emission and the emission over time FEM (finite element methods) modelling was used. Based on this, five samples with a surface of 7 cm2 and a thickness of 12 mm with a content of 1 ‰ styrene were investigated at (23 ± 2) °C and (50 ± 5) % relative humidity in the µ-chamber (3 samples) and 24 L test chambers (2 samples) for 28 days. Air samples were taken after 24 hours, 3, 7, 14, 21 and 28 days on Tenax TA® sorption tubes and analyzed by TD-GC-MS. The area specific emission rate (SERa) was calculated to compare the results from both chamber types. After 24 hours SERa was between 0.8 0.9 µg cm 2 h 1 (3800 4000 µg m 3) for the µ-chamber samples and between 0.9 1.1 µg cm 2 h 1 (300-370 µg m 3) for the 24 L test chamber samples. After 28 days the SERa was at 0.2 µg cm 2 h 1 for all samples. The relative standard deviation of the SERa was between 1 26 %. These results show the applicability of vacuum grease as supporting material and the favored starting concentration range could be achieved in the 24 L test chambers. T2 - Indoor Air 2016, the 14th international conference of Indoor Air Quality and Climate CY - Ghent, Belgium DA - 03.07.2016 KW - Emission test chamber KW - Indoor air KW - Quality assurance KW - Quality control PY - 2016 AN - OPUS4-36823 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hübert, Thomas A1 - Kemnitz, Erhard A1 - Usmani, Shirin A1 - Schlischka, Jörg A1 - Klutzny, Kerstin A1 - de Laval, Yvonne A1 - Plarre, Rüdiger A1 - Krahl, Thoralf A1 - Stephan, Ina T1 - Wood protection with nanoparticles: MgF2 and CaF2 N2 - The potential of alkaline earth metal Fluoride nanoparticles was tested for protection of wood against fungi and termites. These nanoparticles are ideal for wood protection. T2 - School of Analytical Sciences Poster Session CY - Berlin, Germany DA - 06.12.2016 KW - Wood preservation KW - Fluorides KW - Nanoparticles PY - 2016 AN - OPUS4-39141 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hahn, Marc Benjamin A1 - Meyer, Susan A1 - Solomun, Tihomir A1 - Kunte, Hans-Jörg A1 - Sturm, Heinz T1 - Electron irradiation of biomolecules under physiological conditions: Experimental realization and microdosimetric calculations N2 - In the last years, secondary low-energy electrons (LEE) emerged as important, if not predominant, reductive pathway in ionizing damage of biomolecules. These electrons are created in copious amount as result of inelastic scattering of high energy radiation at water. Until now, all experiments the quantification of the effects of LEEs on the biomolecular damage was either performed in vacuum with LEE sources or with DNA on surfaces in humid atmosphere. We present a new experimental setup to irradiate biomolecules with electrons under physiological conditions. In combination with monte carlo simulations this setup makes it possible to determine microdosimetric quantities for biomolecules in liquid environment under electron irradiation. This opens up new possibilities in radiation research to access the LEE damage under well defined physiological condition, for more complex systems, such as DNA-Protein complexes and even living cells. T2 - 14th International Congress of the International Radiation Protection Association CY - Cape Town, South Africa DA - 09.05.2016 KW - DNA KW - Dosimetry KW - Microdosimetry KW - Geant4 KW - Low energy electrons KW - Radicals KW - Radiation damage KW - Polymers PY - 2016 AN - OPUS4-36399 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Veliz Montes, Cinthya A1 - Bottari, G. A1 - Trukina, O. A1 - Torres, Tomás A1 - Schneider, Rudolf T1 - Unsubstituted, covalently-linked phthalocyanine-C60 fullerene dyads N2 - Were prepared four unsubstituted Pc - C60 fullerene systems, using two different synthetic strategies, via Prato (1,3 - dipolar cycloaddition) or Bingel reactions. The precursor Pcs 1 and 2 were successfully synthesized by cyclotetramerization reaction between TBDPS - protected and unsubstituted phthalonitriles. The surface studies are currently ongoing. T2 - PcsTT2016 Symposium CY - Elche, Spain DA - 27.01.2016 KW - Fullerene KW - Phthalocyanine PY - 2016 AN - OPUS4-38556 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cabeza, Sandra A1 - Thiede, Tobias A1 - Mishurova, Tatiana A1 - Nadammal, Naresh A1 - Kromm, Arne A1 - Bruno, Giovanni T1 - Development of residual stresses in IN718 parts obtained by SLM N2 - Additive Manufacturing by Selective Laser Melting (SLM) offers ample scope for producing geometrically complex parts as compared to the traditional subtractive manufacturing strategies. However, the residual stresses (RS) developed during the processing can reduce the load bearing capacity as well as induce unwanted distortion, limiting the application of SLM parts. In the present work, residual stresses in additivly manufactured IN718 part were analised by means of neutron diffraction and synchrotron X-ray diffraction. T2 - ISAM 2017 CY - Dresden, Germany DA - 07.02.2017 KW - Additive manufacturing KW - Residual stress KW - Inconel 718 KW - Netron diffraction KW - Microstructure PY - 2017 AN - OPUS4-39139 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koclega, D. A1 - Radziszewska, A. A1 - Kranzmann, Axel A1 - Huebner, J. A1 - Kac, S. T1 - High temperature corrosion resistance of Inconel 686 coatings in aggresive environments N2 - The work presents the microstructure, chemical composition and mechanical properties of Inconel 686 coatings after high - temperature corrosion in environment of aggressive gases. To produce the Ni - base weld overlays the QS Nd:YAG laser beam was used. The substrates were 13Mo4-5 boilers plate steel. Ni - base alloys characterize the excellent high temperature corrosion resistance, good strength and good ability to work in aggressive environments. Applied overlays had a proper combination of the metal substrate in particular small amount of Fe. This could be achieved by the reduction of the melting of the substrate and its dissolution into the overlays. The microstructure, chemical composition of the obtained overlays were investigated by means of a light microscope, a scanning electron microscope (SEM) equipped with the EDS detector. The overlays had cellular-dendritic structure. The variations of the chemical composition (especially Mo, Ni and W ) in the interdendritic and dendritic regions were observed. The interdendritic regions were enriched during solidifications in Mo and W and had lower content of Ni. T2 - EUROCORR 2017 CY - Prague, Czech Republic DA - 03.09.2017 KW - Inconel 686 KW - Corrosion resistance KW - Laser cladding PY - 2017 AN - OPUS4-44197 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koclega, D. A1 - Radziszewska, A. A1 - Kranzmann, Axel A1 - Dymek, S. A1 - KĄc, S. T1 - The microstructure of weld overlay Ni - base alloy deposited on carbon steel by laser QS-Nd:YAG N2 - Ni- base alloys are used as a one of the most important coating material and can be applied in a different environments and elements of devices having various applications. To protect the surface of the material from aggressive gases at high temperature, there are use different kinds of the Ni- base alloys. One of such alloy is Ni-Cr-Mo-W called commercial Inconel 686. This alloy based on NiCr22Mo9Nb (Inconel 625), in which content of molybdenum increased and niobium was replaced with the addition of tungsten, in order to counteract the strong segregation in the microstructure, which results in homogeneity of the chemical composition of the structure. Inconel 686 is also characterized by greater resistance to high temperature corrosion and heat resistance than Inconel 625. The Inconel 686 alloy was deposited on 13CrMo4-5 steel by laser QS - Nd:YAG. In the poster the microstructure (SEM) and chemical composition (EDS) of obtained weld overlays were investigated. T2 - EUROMAT 2017 CY - Thessaloniki, Greece DA - 17.09.2017 KW - Nickel based alloy KW - Laser cludding KW - High temperature corrosion resistance PY - 2017 AN - OPUS4-44195 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Reinsch, Stefan A1 - Patzig, C. T1 - Surface-initiated microstructure formation in glass ceramics N2 - Up to now, the mechanisms of surface nucleation and surface-induced texture formation are far from being understood. Corresponding phenomena are discussed hypothetically or even controversial, and related studies are restricted to very few glasses. As a main drawback, the vast majority of previous work on oriented growth of surface crystals do not consider the possible effects of glass surface treatments (like polishing defects, adhered particles and cracks, …) or ambient annealing conditions (vacuum or atmospheric pressure) which both can influence crystal nucleation and growth. Moreover, very few observations of crystal orientation related to surface crystallization were focused on separately growing crystals. In conclusion, up to now, no systematic studies on initially oriented crystal growth or nucleation from defined active nucleation sites have been pursued. Therefore, the main objective of the proposed project is to gain a basic understanding of the mechanisms of surface-induced microstructure formation in glass ceramics. We shall answer the question whether preferred orientation of surface crystals is the result of oriented nucleation or caused by other orientation selection mechanisms acting during early crystal growth. In both cases, crystal orientation may be caused by the orientation of the glass surface itself or the anisotropy and orientation of active surface nucleation defects. New techniques of experimental characterization of surface-crystallized glasses shall be applied to find answers to the questions posed above. Based on a controlled preparation and annealing of the glass sample surfaces, that includes the defined creation of active nucleation defects, and followed by the microstructural characterization especially during the very early growth stages of separated surface crystals, the orientation relations between defect and initiated surface crystal will be analyzed. In order to gain new insights, a couple of entirely new microstructure diagnostics techniques, including chemically contrasted XRM, laser-based sample preparation for XRM, and 3D electron backscatter diffraction shall be developed or applied. This way, using X-ray microscopy as a pivotal technique for the non-destructive 3D characterization of relatively large samples at superior spatial resolution (but also complemented by other microstructure diagnostics techniques, e.g. TEM elemental mappings at cross-sectioned samples) unprecedented insights into the microstructure evolution upon surface crystallization of model glasses will be gained. T2 - DFG Begutachtungskolloquium (PAK 949/1 und PAK 950/1) CY - Bonn, Germany DA - 07.03.2017 KW - Oberflächenkeimbildung KW - Glaskeramik KW - Orientierung PY - 2017 AN - OPUS4-44221 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gollwitzer, Christian A1 - Cabeza, Sandra A1 - Garces, G. T1 - Synchrotron based absorption edge tomography for §D characterization of the microstructure of MG-Y-Zn alloys N2 - Absorption edge tomography is a method which exploits the sudden change of the attenuation coefficient, when the photon energy crosses the absorption edge of an element. The beamline BAMline at BESSY II, which is operated by the Federal Institute for Materials Research and Testing, can provide a monochromatized beam in a photon energy range from 5 keV up to 80 keV with a bandwidth of 2%. Together with the microtomography setup, this enables differential tomography sensitive to any element with N >= 24 (Cr) by using an appropriate K- or L-edge in this range. Here, absorption edge tomography at the Yttrium edge is employed to perform a non-destructive 3D characterization of the microstructure of a high strength Mg-Y-Zn alloy. The long period stacking ordered (LPSO) phase which forms fibres in this material was extracted based on the Yttrium content and the fibre length distribution was analysed. T2 - Ninth Joint BER II and BESSY II User Meeting CY - Berlin, Germany DA - 13.12.2017 KW - Synchrotron KW - Computed Tomography KW - Absorption edge KW - BAMline PY - 2017 AN - OPUS4-43854 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Falk, Florian A1 - Menneken, Martina A1 - Stephan-Scherb, C. T1 - Early oxidation and sulfidation of high temprature alloys: An EDXRD in-situ study N2 - P92 is one of the important steels for super heater tubes used in combustion plants. However, in fossil fuel fired environments the formation of oxides and sulfides are challenging the material. To understand early corrosion mechanisms, which are important for process prediction, high temperature in-situ ageing experiments of Fe-Cr-Mn alloys in SO2 and SO2+H2O atmosphere were performed, applying energy dispersive X-ray diffraction (EDXRD) analysis. T2 - Bessy usermeeting CY - Berlin, Germany DA - 05.12.2017 KW - Corrosion KW - In-situ KW - EDXRD PY - 2017 AN - OPUS4-45368 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wollschläger, N. A1 - Nützmann, Kathrin T1 - What happens during S-corrosion in Fe13Cr in the early stage? N2 - Ferritic alloys containing Cr form Cr5S6 precipitates along grain boundaries in hot SO2 environment. Grain boundary precipitates may influence the steel’s mechanical behavior. Cr5S6 precipitates were reconstructed three-dimensionally using FIB tomography analysis to determine the volume, number, and penetration depth. The volume growth of Cr5S6 precipitates increased only for the initial aging time of 3 h but became constant after 6 h. The number of precipitates increased linearly. T2 - Meeting on Focused Ion Beams in Berlin - FIBiB2017 CY - Berlin, HZB Wannsee Campus, Germany DA - 06.11.2017 KW - Grain boundary corrosion KW - 3D tomography KW - Sulfidation PY - 2017 AN - OPUS4-45061 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koclęga, Damian A1 - Dymek, S. A1 - Radziszewska, A. A1 - Huebner, J. T1 - Optimization of laser treatment parameters of Inconel 686 overlay weld on carbon steel 13Mo4-5 N2 - The work presents the effects of the change of the laser cladding parameters on microstructure, chemical composition and mechanical properties of Inconel 686 overlays (coatings). To obtain the best quality of these coatings the various parameters of laser cladding such as the power density of the laser beam, the laser beam velocity and overlapping ratio of the weld tracks were applied. The substrates were boilers plate made of the 13Mo4-5 steel. Ni - base alloys characterize by the excellent high-temperature corrosion resistance, good strength and good ability to work in aggressive environments. Applied overlays had a proper combination of the metal substrate in particular small amount of Fe. This could be achieved by the reduction of the substrate melting and its dissolution into the overlays. The microstructure, chemical composition of the obtained overlays were investigated by means of a light microscope, a scanning electron microscope (SEM) equipped with the EDS detector. The overlays had cellular-dendritic structure. The variations of the chemical composition (especially Mo, Ni and W ) in the interdendritic and dendritic regions were observed. The interdendritic regions were enriched during solidifications in Mo and W and had lower content of Ni. T2 - METAL 2017 CY - Brno, Czech Republic DA - 24.05.2017 KW - Laser cladding KW - Overlay KW - Chemical composition KW - Inconel 686 PY - 2017 AN - OPUS4-44464 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kotaka, M. A1 - Honma, T. A1 - Shinozaki, K. A1 - Affatigato, M. A1 - Müller, Ralf A1 - Komatsu, T. T1 - Unique growth behavior of ferroelastic beta’-Gd2(MoO4)3 crystals in glasses N2 - An understanding on crystallization behavior and kinetics in glasses is one of the important topics in the glass science and technology. Tsukada et al.1) found an extremely unique and curious phenomenon in the crystallization of multiferroic (ferroelectric and ferroelastic properties) ’-Gd2(MoO4)3 crystals in Gd2O3-MoO3-B2O3 glasses. That is, crystals formed in the crystallization break into small pieces with a triangle prism or pyramidal shape having a length of 50-150 um spontaneously during the crystallization in the inside of an electric furnace, not during the cooling in air after the crystallization. They proposed to call this phenomenon “self-powdering phenomenon”. To the best of our knowledge, such a self-powdering phenomenon has not been observed in the crystallization of any other glasses. To investigate this phenomenon is very important for the glass science and for the preparation of bulk crystallized glasses with ferroelastic crystals. In this work, the preparation of crystallized glasses keeping the original shape is challenged, and the mechanism of self-powdering phenomenon is proposed. Glasses with the compositions of 21Gd2O3-63MoO3-(16-x)B2O3-xTeO2 (mol%) (x=0, 2, 4, 8) such as 21Gd2O3-63MoO3-16B2O3 (GM16B) and 21Gd2O3-63MoO3-8B2O3-8TeO2 (GM8T8B) were prepared using a conventional melt quenching technique. The quenched glasses were heat-treated at some temperatures, and the crystalline phase present in the crystallized samples was identified by X-ray diffraction (XRD) analyses, and the morphology and birefringence of crystals formed were observed using a polarized optical microscope (POM). The densities of GM16B and GM8T8B glasses are 4.76 g/cm3 and 4.91 g/cam3, respectively, and these values are higher than the density of ’-Gd2(MoO4)3 crystal, 4.555 g/cm3. These differences in the density might induce the large stresses in the inside of crystals during the crystal growth. The crystallized glasses of GM16B with ’-Gd2(MoO4)3 crystals do not keep the original glass shape, showing self-powdering phenomenon (breaking into small pieces). However, the crystallized glasses of GM8T8B keep the original glass shape without indicating any self-powdering. It is proposed that the stress at the interface between the glassy phase and ’-Gd2(MoO4)3 crystalline phase might be reduced in GM8T8B glasses containing TeO2 with weak Te-O bonds. T2 - Crystallization 2017 CY - Segovia, Spain DA - 10.09.2017 KW - Glass KW - Crystallization KW - Self-powdering PY - 2017 AN - OPUS4-44403 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stephan-Scherb, Christiane A1 - Nützmann, Kathrin T1 - Real time observation of crystallization and growth of corrosion products by energy dispersive X-ray diffraction N2 - Ferritic-martensitic high temperature alloys are widely used as boiler tube and heat exchanger materials in combustion based power plants. All technologies have in common that the applied materials are exposed to different temperatures, process pressures and reactive atmospheres which lead to a change of the material properties and a further degradation of the material. To date corrosion analytics mainly proceeds via the use of various microscopic techniques and the analysis of the corrosion products after the reaction is completed. Comprehensive efforts have been made to study high temperature corrosion by the use of environmental SEM’s or in-situ TEM technologies. The here presented work will show a different approach to study high temperature gas corrosion in a multiple gas atmosphere by energy dispersive X-ray diffraction (EDXRD). For this technique high energetic white X-ray radiation (10-100 keV) was used as radiation source instead of conventional monochromatic radiation. It enables us to study crystallization procedures on short and medium time scales (1 min < t < 24 h) and the collection of Bragg-Signals of the phases of interest as a function of process time. Their occurrence can directly be correlated with thermodynamic and kinetic parameters. A special designed corrosion reactor was used to combine high temperature gas corrosion experiments with the collection of diffraction patter. The crystallization and reaction paths for oxide and sulfide formation was followed in-situ on Fe-Cr and Fe-Cr-Mn model alloys in a hot SO2 containing (T=650 °C) atmosphere. T2 - Gordon Research Conference on High Temperature Corrosion and Protection of Materials CY - New London, NH, USA DA - 09.07.2017 KW - Corrosion KW - In situ diffraction KW - Crystallization PY - 2017 AN - OPUS4-44717 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Höhne, Patrick A1 - Kuchenbecker, Petra A1 - Lindemann, Franziska A1 - Güther, Wolfgang A1 - Rabe, Torsten T1 - Utilization of an ultra sound atomizer for spray granulation of oxide ceramic fine powder N2 - Spray drying based granulation processes aim for flowable granules neither containing voids nor hard shells thus leading to a homogenous microstructure in the green and sinter bodies without strength reducing large pores. The increase of the specific surface area due to the utilization of finer powders as raw materials makes the production of granules of demanded quality more sophisticated. Innovations regarding additives as well as process engineering are therefore required. While conventional spray granulation processes of ceramic materials are based on rotational, one stream or two stream nozzles for nebulization, the investigations in the ZIM project concentrate on the applicability of an ultra sound atomizer unit. A spray dryer comprised of the aforementioned ultra sound atomization unit implemented in a commercial spray dryer (Niro, Denmark) was used as test system. Potential advantages of the ultra sound nebulization are investigated for model systems of alumina, zirconia and a ZTA composite while focusing on solids content, yield, pressability and granule properties (size, size distribution, flowability, shape and microstructure) as well as the final sinter body properties (density, microstructure and flexural strength). First ultra sound spray drying experiments yielded granules with excellent processability. Spray drying of identical slurries, as before tested and optimized for a two stream nozzle atomization process, resulted in a more suitable size distribution for dry pressing (less particles below 20 µm) and a higher yield. Furthermore, sinter bodies produced of ultra sound granules seem to have less large pores and a more homogenous microstructure T2 - 92. Jahrestagung der deutschen keramischen Gesellschaft CY - Berlin, Germany DA - 20.03.2017 KW - Ceramics KW - Spray drying KW - Ultra sound KW - Atomization KW - Microstructure PY - 2017 AN - OPUS4-39588 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank A1 - Sklorz, Christian T1 - Testing of pressurized vessels N2 - The results are based on data1. Figure 3 displays temperatures of the tank wall and of the gas phase over testing time. It can be seen that a complete coating strongly delayed the heating of tank wall and gas phase, whereas the partly coated tanks only had a minor influence on temperature development. There was no significant difference between a half coated and a thirdly coated tank measurable. Figure 4 shows the internal pressure of tanks over testing time. Only the fully coated tank enabled a low pressure over 90 min testing time. Hence, a complete coating is necessary to guarantee the fire safety of hazmat tanks and a partly coating is not sufficient. T2 - Annual Conference on Engineering and Information Technology CY - Nagoya - Japan DA - 29.03.2017 KW - Fire KW - Testing KW - Vessels KW - Dangerous goods PY - 2017 AN - OPUS4-39843 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlichting, S. A1 - Hönig, Gerald M. O. A1 - Wagner, M. R. A1 - Müßener, J. A1 - Hille, P. A1 - Teubert, J. A1 - Schörmann, J. A1 - Eickhoff, M. A1 - Hoffmann, A. A1 - Callsen, G. T1 - Tuning of the quantum-confined Stark effect in wurtzite [0001] nanostructures by the internal-field-guarded-active-region design N2 - In this work we eliminate the QCSE without having any special requirements on the growth procedure or the material. Hönig et al. developed the Internal-Field-Guarded-Active-Region Design (IFGARD), which we experimentally investigate in this work based on GaN/AlN nanodiscs (NDs). T2 - Compound Semiconductor Week 2017 CY - Berlin, Germany DA - 14.05.2017 KW - Halbleiterphysik KW - Nanophysik KW - Optoelektronik KW - Piezopolarisation KW - Spontane Polarisation PY - 2017 AN - OPUS4-40174 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hoffmann, Katrin A1 - Tschiche, Harald Rune A1 - Resch-Genger, Ute T1 - Fluorescence microscopic and spectroscopic monitoring of degradation processes upon polymer ageing N2 - The majority of all routinely used methods to assess polymer aging are based on destructive tests and methods. Early indicators for the deterioration of polymer materials are e.g., physical or mechanical properties like tensile strength, adhesion, brittleness, and color. It is well-known, however, that predominantly chemical changes are the underlying process of the physical changes that occur in organic materials upon aging over time. Typical initial steps during polymer degradation are crosslinking or chain breaking, alteration of autofluorescence, “yellowing” or bleaching caused by the formation of new functional groups. A straightforward strategy towards the sensitive detection and monitoring of chemical changes in the course of polymer aging is based on non-destructive optical measurements. Luminescence techniques, one of the most sensitive spectroscopic methods are the method of choice. Here, we present first results of luminescence-based monitoring of polymer degradation induced by different environmentally relevant weathering factors (e.g. humidity and UV exposure). Our studies include fluorescence spectroscopy as well as spectral scanning confocal fluorescence microscopy and clearly demonstrate the possibility to follow accelerate-aging processes by luminescence detection. T2 - Focus on Microscopy 2017 CY - Bordeaux, France DA - 09.04.2017 KW - Polymer aging KW - Confocal fluorescence microscopy KW - Fluorescence spectroscopy KW - Surface functionalities PY - 2017 AN - OPUS4-40274 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tschiche, Harald A1 - Hoffmann, Katrin A1 - Radunz, Sebastian A1 - Schwibbert, Karin A1 - Sameith, Janin A1 - Toepel, Jörg A1 - Resch-Genger, Ute T1 - A Polymeric Nanosensor for Sensing of Broad pH Changes in Biofilm as Tool for the Investigation of Microbial Induced Corrosion N2 - One of today’s major problems in many technical plants as well as fuel tanks is Microbial induced corrosion (MIC), leading to considerable damage and huge financial losses. Successful prevention of MIC requires the localization of first signs of corrosion as well as the identification of factors influencing the corrosion process. Hence, there is a growing need for sensitive and preferably inexpensive tools that enable the early detection of MIC. Of utmost importance are methods, which provide spatially and time-resolved information and allow the determination of corrosion rates at sites of interest for possible prevention of MIC. T2 - First European / 10th German BioSensor Symposium CY - Potsdam, Germany DA - 20.03.2017 KW - Nanoparticel based pH-probes KW - Microbial induced corrosion KW - Imaging PY - 2017 AN - OPUS4-40261 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tschiche, Harald A1 - Hoffmann, Katrin A1 - Falkenhagen, Jana A1 - Weidner, Steffen A1 - Resch-Genger, Ute T1 - Determination of degradation products of thermoplastic polyurethane using fluorescent sensors in a model system N2 - Polyurethanes (PU) are formed by polyaddition reaction between diols and diisocyantes. They can be formed utilizing three building blocks, namely a polyol or long-chain diol, a chain extender or short-chain diol, and a diisocyanate. The derived multi-phase block copolymer has thermoplastic properties and is called thermoplastic PU (TPU). This modular approach allows for a variety of alternations yielding a broad range of structural properties and applications. TPUs are based on three main classes of polyols, i.e. polyethers, polyesters, and polycaprolactones. With these different polyols and the ability of changing the ratio of building blocks a variety of material properties can be obtained thus TPUs find numerous applications in e.g. lightweight construction1, insulation, flame retardants, lacquer and glue, as well as medicine. Linear, isocyanate terminated, polyurethane prepolymers prepared from non-equivalent amounts of diisocyanate such as methylene diphenyl diisocyanate (MDI) attached to a polyol are widely used as precursors of the correspondent polymers. Chain-extending reactions with low molecular weight compounds bearing different amounts of active hydrogens enable both linear and crosslinked polyurethane to be formed. Due to TPUs being used in a broad range of applications facing a variety of stress (e.g. mechanical, hydrolytic, thermal, radiative/UV, as well as its combinations) the complexity of possible degradation mechanism is high. A functional group derived from degradation of the bulk matrix can be detected utilizing a suited fluorogenic sensor molecule. There are several fluorogenic dyes known for the application as sensor for amine groups e.g. fluorescamine, pyrylium dyes, deriving a fluorescent signal upon reaction. T2 - ANAKON 2017 CY - Tübingen, Germany DA - 03.04.2017 KW - Bewitterung KW - Polyurethan KW - Functional group detection KW - Polyurethanes PY - 2017 AN - OPUS4-40262 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agudo Jácome, Leonardo T1 - Experimental study on M23C6 nucleation and growth mechanisms in Ni-base superalloy single crystals N2 - The addition of carbon to Ni-base superalloy single crystals has been increasingly carried out to improve low angle grain boundary (LAGB) resistance and castability. Consequently, the precipitation of carbides is highly probable during long-term application of components subjected to higher temperatures (> 1000 °C). While the view on the role of carbides as strengthening or detrimental is polemical, their inevitable increased presence in carbon-doped alloys must be addressed. In the present work, the evolution of M23C6 carbides forming in the commercial grade Ni-base superalloy LEK 94 during high-temperature and low-stress creep exposure is assessed. Although carbon is not intentionally added to the LEK 94 alloy, it admits up to 0.1 at. %, which together with the high content of M23C6-forming transition metals, leads to their precipitation. The precipitation is induced here during creep experiments at 1020 °C and a nominal applied stress of 160 MPa along [001]. The correlation of precipitation and external load is carried out by evaluating the carbides in the gage section of parallel and circularly notched cylindrical samples, as well as in their heads. Characterization is made by transmission electron microscopy (TEM). Although primary MC carbides form mostly in interdendritic regions during casting, high temperature exposure induces M23C6 carbide nucleation especially in the γ phase of dendritic regions, where a stronger partitioning of refractory elements is present. The carbides have a needle shape with their main axis on 〈100〉 and a cube-on-cube orientation relationship. They present incoherent {100} facets along their elongated region and semi-coherent {111} facets at their ends. Their nucleation and growth mechanisms are discussed based on microstructural observation under different experimental conditions. T2 - Modelling and Simulation of Superalloys. International Workshop. CY - Bochum, Germany DA - 29.03.2017 KW - Ni-base superalloy KW - Single cystal KW - Creep KW - Carbide KW - Scanning transmission electron microscopy (STEM) PY - 2017 AN - OPUS4-40249 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kulla, Hannes A1 - Becker, C. A1 - Casati, N. A1 - Paulus, B. A1 - Rademann, K. A1 - Emmerling, Franziska T1 - In situ investigations of a mechanochemical cocrystal formation by X-ray diffraction for two different milling jar materials N2 - Mechanochemistry has become a valuable method for the synthesis of new materials, especially for pharmaceutical cocrystals. The Advantages of fast reactions in high purity and yield face a lack of understanding the underlying mechanism. Therefore, in situ setups to study mechanochemical reactions have been established. Herein, we present an in situ investigation of the mechanochemical cocrystal formation of pyrazinamide (PZA) with pimelic acid (PM) using synchrotron XRD. Two new polymorphs of PZA:PM (1:1) were synthesized by milling the starting materials in milling jars of different materials. While Form I is only obtained using a steel jar, Form II can be obtained purely in jars made of Perspex. In situ XRD experiments reveal a direct formation of Form II in Perspex and an intermediate formation of Form II in steel jars converting to Form I upon further grinding. Heating experiments and DFT calculations predict that Form II is the thermodynamically more stable polymorph. Therefore, the reaction progress in the steel jar contradicts Ostwald’s rules of stages as the more stable Form II converts into the metastable Form I. Hence, mechanochemistry offers the possibility to synthesize new materials that cannot be obtained using conventional methods. T2 - Adlershofer Forschungsforum 2017 CY - HU-Berlin, Erwin-Schrödinger Zentrum, Germany DA - 10.11.2017 KW - Cocrystal KW - Mechanochemistry KW - Polymorph KW - In situ KW - Milling PY - 2017 AN - OPUS4-42956 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schulte, Petra T1 - Kritische Bewertung der Prüfergebnisse in chemikalienrechtlichen Verfahren: Wie agiert die Behörde? Welche Folgen haben die Ergebnisse für die Rechtsetzung? N2 - Mit nicht-konformen oder schlecht dokumentierten Prüfergebnissen können weder Behörden noch Unternehmen etwas anfangen. Belastbare und eindeutige Informationen aus den Registrierungsdossiers sind entscheidend, damit industrielle und gewerbliche Verwender der Stoffe das Gefahrenpotenzial einschätzen und ggf. Maßnahmen zum Schutz von Menschen und Umwelt treffen können. Darüber hinaus benötigen die Behörden verlässliche Daten aus den Registrierungen, um ihrer Verantwortung bei der Identifizierung regulierungsbedürftiger Stoffe nachkommen zu können. T2 - 13. Fachtagung "Anlagen-, Arbeits- und Umweltsicherheit" CY - Köthen, Germany DA - 16.11.2017 KW - Prüfmethoden KW - Einstufung KW - REACH KW - CLP KW - Registrierungsdossiers KW - SIEF KW - Qulitätssicherung KW - IUCLID KW - ECHA KW - OECD PY - 2017 AN - OPUS4-43081 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Myrach, Philipp A1 - Ziegler, Mathias A1 - Unnikrishnakurup, Sreedhar A1 - Puthiyaveettil, N. A1 - Kruschke, H. A1 - Balasubramaniam, Krishnan T1 - Online Laser-thermografische Rissprüfung an Stahl bei hohen Temperaturen N2 - Die Detektion bzw. Charakterisierung von Oberflächenrissen in Stahl ist eine herausfordernde Aufgabe für die zerstörungsfreie Prüfung. Dies gilt insbesondere, wenn eine solche Prüfung bereits während der Produktion selbst erfolgen soll. Die hier vorgefundenen Randbedingungen, wie z.B. die hohen Probentemperaturen (>700°C) oder Vorschubgeschwindigkeiten von bis zu 0,9 m/min, machen die Anwendung etablierter und vor allem berührender ZfP-Methoden praktisch meist unmöglich. Laser-thermografische Verfahren können hier eine Alternative bieten, da sie berührungslos und schnell arbeiten. Wir stellen die Ergebnisse einer Weiterentwicklung der Laser-thermografischen Prüfung vor, bei der die Anwendbarkeit bzw. die Übertragbarkeit der Methode auf die Bedingungen der Stahlproduktion untersucht wurde. Neben der Simulation der Produktionsbedingungen im Labor und der experimentellen Untersuchung der entscheidenden Einflussgrößen, wurden umfangreiche FEM-Simulationen durchgeführt. Mit Hilfe dieser theoretischen und experimentellen Ergebnisse wurde das Verfahren auch hinsichtlich der Analyse-Algorithmen weiterentwickelt, um eine zuverlässige und schnelle In-Line Prüfung während des Produktionsprozesses zu ermöglichen. Um zudem die Fähigkeiten der Thermografiekamera für schnelle online-Messungen und ihre Integrierbarkeit in verschiedene Anwendungssysteme zu verbessern, wurde die für die Verarbeitung der Detektordaten erforderliche Non-Uniformity Correction der Pixeldaten auf schneller Spezialhardware innerhalb der Kamera implementiert. T2 - Thermografie-Kolloquium 2017 CY - Berlin, Germany DA - 28.09.2017 KW - Rissprüfung KW - Laserthermografie KW - Thermografie KW - Risse PY - 2017 AN - OPUS4-42922 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Moldenhauer, Laura A1 - Helmerich, Rosemarie A1 - Köppe, Enrico A1 - Wittmann, Jochen T1 - Experimental modeling approach for determining the moisture damping exponent of a bluetooth low energy signal in moist building material N2 - We investigated, the damped Received Signal Strength Indicator (RSSI) of a Bluetooth Low Energy (BLE) signal, transmitted from the BLE-module embedded in building materials with changing moisture content, Fig. 1. The BLE-module communicates with a mobile Smart Device as tablet via 2.45 GHz-ISM-frequency band where water dipoles start to oscillate, Fig. 2. The damping model demonstrates this damping effect on RSSI by the abstraction of the reality observed in a real system. Through the reproduction of the active relationships, the system behavior is decomposed in such a way that a separate consideration of the required system parameters is possible. T2 - 34th DANUBIA ADRIA SYMPOSIUM on Advances in Experimental Mechanics (DAS 2017) CY - Trieste, Italy DA - 18.09.2017 KW - Structural health monitoring KW - Long-term monitoring KW - Bluetooth Low Energy KW - BLE KW - Moisture KW - Network Communication KW - Experimental study KW - Modellierung PY - 2017 AN - OPUS4-42966 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Evsevleev, Sergei A1 - Mishurova, Tatiana A1 - Cabeza, Sandra A1 - Bruno, Giovanni T1 - Damage Analysis in Metal Matrix Composites by means of Synchrotron Radiation Computed Tomography N2 - The damage evolution after compression tests of two types of MMC, consisting of eutectic AlSi12CuMgNi alloy and reinforced with 15vol% of Al2O3 fibers and with 7vol% of Al2O3 fibers+15vol% of SiC particles was studied by synchrotron CT. Internal damage at different pre-strain conditions in eutectic Si, intermetallic phases and Al2O3 fibers was observed, as well as debonding of SiC particles. T2 - HZB User Meeting CY - BESSY II, Berlin, Germany DA - 14.12.2017 KW - Aluminum KW - Metal Matrix Composite KW - Damage Analysis KW - Computed tomography KW - Synchrotron Radiation PY - 2017 AN - OPUS4-43467 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thiede, Tobias A1 - Mishurova, Tatiana A1 - Cabeza, S. A1 - Nadammal, Naresh A1 - Bode, Johannes A1 - Kromm, Arne A1 - Haberland, C. A1 - Bruno, Giovanni T1 - Influence of deposition hatch length on residual stress in selective laser melted Inconel 718 N2 - Additive Manufacturing (AM) by Selective Laser Melting (SLM) offers ample scope for producing geometrically complex parts in comparison to the traditional subtractive manufacturing strategies. Developing during the manufacturing process, residual stresses may limit the application of SLM parts by reducing the load bearing capacity as well as induce unwanted distortion depending on the boundary conditions specified in manufacturing. The present study aims to evaluate the bulk residual stresses in SLM parts by using neutron diffraction measurements performed at E3 line -BER II neutron reactor- of Helmholtz-Zentrum für Materialien und Energie (HZB) Berlin. Together with microstructure characterization and distortion measurements, it is possible to describe the stress state throughout the whole sample. The sample was measured in as-build condition (on a build plate) and after releasing from the build plate. The used material is the nickel based superalloy 718. This alloy is widely used in aerospace and chemical industries due to its superior corrosion and heat resistant properties. Obtained results indicated different residual stress states for each of the transversal, longitudinal and normal component. The normal and transversal component exhibits a rather compressive behavior while the longitudinal was tensile in the center part of the sample and became compressive towards the tip. As expected, the absolute values of all stress components decreased after releasing the sample from the building plate. A surface scan utilizing a coordinate-measuring machine (CMM) allowed us to present top surface distortion before and after releasing. The top surface showed a distortion around ±80µm after releasing. Microstructure evolution in the scanning-building cross-section is largely dominated by columnar grains. In addition, many small random orientated grains are prominent in the regions of a laser overlap during SLM. In summary, for the sample of superalloy 718 manufactured by SLM, a small distortion occurred when removing the sample from the build plate whereby the residual stress state decreases. Moreover, the observed columnar grains in the building direction could give a reason for the lowest stress values in that normal direction. However, the most important parameter controlling the residual stresses is the temperature gradient. Hence, future investigations are planned for a different scan strategy to distribute the laser impact in a more homogenous manner. T2 - HZB User Meeting 2017 CY - Berlin, Germany DA - 15.12.2017 KW - AM KW - SLM KW - IN 718 KW - Neutron diffraction KW - Residual stress KW - Hatch length KW - Microstructure PY - 2017 AN - OPUS4-43475 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hampel, Marco A1 - Dimper, Matthias A1 - Schenderlein, Matthias A1 - Özcan Sandikcioglu, Özlem T1 - A new approach for high-resolution analysis of early-stage corrosion processes N2 - The poster presentation summarizes the recent developments on the combination of scanning electrochemical microscopy with multielectrode arrays for the investigation of local corrosion processes. T2 - GfKORR Jahrestagung 2017 CY - Frankfurt am Main, Germany DA - 07.11.2017 KW - Scanning electrochemical microscope (SECM) KW - Multielectrode array sensors KW - Corrosion PY - 2017 AN - OPUS4-43459 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dimper, Matthias A1 - Hampel, Marco A1 - Schenderlein, Matthias A1 - Özcan Sandikcioglu, Özlem T1 - Multielectrode array probes for early detection of corrosion processes N2 - Multielectrodes are arrays of single electrodes arranged in a particular geometry. In our work, all the single electrodes are identical stainless steel X5CrNi18-10 (1.4301) wire electrodes. Using a multielectrode analyser all single electrodes are connected via zero resistance ammeters, simulating a galvanically coupled single electrode surface. The advantage of the multielectrode analyser (MMA) is that the currents flowing between single electrodes can be measured. Thus, real-time maps can be generated indicating where anodic and cathodic areas lie on the surface of the multielectrode and how they behave. The combination of the multielectrode analyser with the scanning electrochemical microscopy (SECM) enables the identification of corrosion sites and the detailed electrochemical analysis. T2 - DECHEMA/GfKORR-Fachgruppe "Mikrobielle Materialzerstörung und Materialschutz" CY - Berlin, Germany DA - 04.10.2017 KW - Scanning electrochemical microscope (SECM) KW - Multielectrode array sensors KW - Corrosion PY - 2017 AN - OPUS4-43461 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fontana, P. A1 - Miccoli, L. A1 - Meng, Birgit T1 - Healthier life with eco-innovative components for housing constructions N2 - The project has developed a variety of new multifunctional and flexible building components for a healthier indoor environment. [H] house solutions are durable, energy efficient, safe and affordable. They are suitable for use in new buildings and for renovation. [H] house solutions cover aspects of long service life, reduced maintenance and long-term improvement of energy efficiency. T2 - H-House Abschluss-Kolloquium, Dauerausstellung am Demonstrator-Gebäude CY - Warsaw, Poland DA - 23.08.2017 KW - Building materials KW - Beton KW - UHPC PY - 2017 AN - OPUS4-43003 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kulla, Hannes A1 - Becker, Christian A1 - Casati, Nicola A1 - Paulus, Beate A1 - Rademann, Klaus A1 - Emmerling, Franziska T1 - In situ PXRD monitoring of a mechanochemical cocrystal formation in milling jars of different material N2 - We present an in situ PXRD investigation of the mechanochemical cocrystal formation of pyrazinamide with pimelic acid in two milling jar materials. In the steel jar a polymorph transformation presenting an exception of Ostwald’s rule of stages is observed. T2 - BESSY User Meeting 2017 CY - Bessy II (HZB), Berlin, Germany DA - 14.12.2017 KW - In situ KW - XRD KW - Polymorph KW - Cocrystal KW - Milling PY - 2017 AN - OPUS4-43502 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kormunda, M. A1 - Hertwig, Andreas A1 - Beck, Uwe A1 - Fischer, Daniel T1 - Study of magnetron sputtering deposited ultrathin FeSnOx films for Surface Plasmon Resonance sensors towards gas sensing applications N2 - In this study, series of coatings with the goal of sensitising gold SPR sensors towards CO, NH4, etc. were prepared. To better understand the mechanism behind the sensitizing effect and to enable the targeted production of optimized layers, the wide range of coatings was studied by multiple methods from spectroscopic ellipsometry for their dielectric function, by XPS for chemical composition and SEM, TEM to determine their microscopic structure. The coatings were deposited at inert Ar gas and reactive Ar/O2 gas mixture by RF magnetron sputtering or DC pulsed magnetron sputtering with settable RF bias on the substrates. The plasma processes were monitors by mass spectrometry. The metal oxide coatings in SPR sensors have to be prepared reproducible with thickness about 5 nm therefore lower deposition rate conditions were advantages. T2 - THE 14th INTERNATIONAL SYMPOSIUM ON SPUTTERING & PLASMA PROCESSES,ISSP 2017 CY - Kanazawa, Japan DA - 05.07.2017 KW - Surface Plasmon Resonance KW - Magnetron sputtering KW - FeSnOx PY - 2017 AN - OPUS4-43536 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Emmerling, Franziska A1 - Kulla, Hannes A1 - Wilke, Manuel T1 - In situ investigations of mechanochemical reactions - new insights in formation pathways N2 - Mechanochemistry is increasingly used for synthesizing soft matter materials including metal organic compounds and cocrystals. The ever-increasing interest in this method is contrasted by a limited mechanistic understanding of the mechanochemical reactivity and selectivity. Time-resolved in situ investigations of milling reactions provide direct insights in the underlying mechanisms. We recently introduced a setup enabling in situ investigation of mechanochemical reactions using synchrotron XRD combined with Raman spectroscopy. The specific combination allows to study milling processes comprehensively on the level of the molecular and crystalline structure and thus obtaining reliable data for mechanistic studies. In situ Raman spectroscopy coupled with thermography revealed a low temperature increase during milling reactions due to the mechanical impact and clear temperature increases because of the reaction heat. Based on the data, temperature rises as postulated in the magma plasma and hot spot theory can be excluded for soft matter milling syntheses. Our results indicate that in situ investigation of milling reactions offer a new approach to tune and optimize mechanochemically synthesized compounds. T2 - Wissenschaftsforum Chemie CY - Berlin, Germany DA - 10.09.17 KW - Mechanochemistry KW - In situ PY - 2017 AN - OPUS4-43563 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kelly, U. A1 - Richter, S. A1 - Schladitz, K. A1 - Scheuerlein, C. A1 - Redenbach, C. A1 - Wolf, F. A1 - Ebermann, P. A1 - Lackner, F. A1 - Schoerling, D. A1 - Meinel, Dietmar T1 - Nb3Sn wire shape and cross sectional area inhomogeneity in Rutherford cables N2 - During Rutherford cable production the wires are plastically deformed and their initially round shape is distorted. Using X-ray absorption tomography we have determined the 3D shape of an unreacted Nb3Sn 11 T dipole Rutherford cable, and of a reacted and impregnated Nb3Sn cable double stack. State-of-theart image processing was applied to correct for tomographic artefacts caused by the large cable aspect ratio, for the segmentation of the individual wires and subelement bundles inside the wires, and for the calculation of the wire cross sectional area and shape variations. The 11 T dipole cable cross section oscillates by 2% with a frequency of 1.24 mm (1/80 of the transposition pitch length of the 40 wire cable). A comparatively stronger cross sectional area variation is observed in the individual wires at the thin edge of the keystoned cable where the wire aspect ratio is largest. T2 - 13th European Conference on Applied Superconductivity, EUCAS 2017 CY - Geneva, Switzerland DA - 17.09.2017 KW - X-ray computer tomography KW - Image processing KW - Superconducting KW - CERN KW - µCT PY - 2017 AN - OPUS4-43493 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lüth, Peter A1 - Brandes, E. A1 - Frost, K. A1 - Kurth, Lutz A1 - Schmidt, Martin A1 - Michael-Schulz, Heike A1 - Uhlig, S. T1 - CEQAT-DGHS Ringversuchsprogramm für die Chemikaliensicherheit – Methodenvalidierung N2 - Bei der Bewertung der Verlässlichkeit der im Labor gewonnenen Prüfergebnisse spielen Ringversuche eine entscheidende Rolle. Die Bundesanstalt für Materialforschung und –prüfung (BAM) unterstützt deshalb den weiteren Ausbau des Ringversuchsprogramms des im Jahr 2007 gegründeten Kompetenzzentrums zur Qualitätssicherung für Prüfungen von Gefahrgütern und Gefahrstoffen auf physikalische Gefahren (Centre for quality assurance for testing of dangerous goods and hazardous substances, CEQAT-DGHS). Bei allen bisher untersuchten Prüfmethoden besteht ein Verbesserungsbedarf. Die RV müssen daher zunächst auf die Methodenentwicklung, -verbesserung und -validierung und auf die Bestimmung der Messunsicherheit der jeweiligen Prüfmethode abzielen und nicht auf Leistungstests. T2 - 13. Fachtagung Anlagen-, Arbeits- und Umweltsicherheit CY - Köthen, Germany DA - 16.11.2017 KW - Gefahrgut KW - Gefahrstoff KW - Ringversuch KW - Prüfmethode KW - Validierung KW - Qualitätssicherung PY - 2017 AN - OPUS4-43301 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Aristia, Gabriela A1 - Bäßler, Ralph A1 - Roth, C. T1 - SiO2-haltige organische Beschichtung für geothermische Anwendungen N2 - Geothermieanlage werden teilweise unter extremen Bedingungen mit sehr salzhaltigen Wässern betrieben. Obwohl C-Stahl häufig für die Konstruktion verwendet wird, ist er in einem Hoch-temperatur- und Hochdrucksystem anfällig für gleichmäßige und örtliche Korrosion. Daher soll ein Beschichtungssystem den C-Stahl schützen. Schlussverfolgung Es ist notwendig, die optimale SiO2-Zugabe zur organischen Beschichtung zu untersuchen, damit deren Eigenschaften, wie z.B. Haftfestigkeit, optimale Schichtdicke, und Temperaturbeständigkeit, verbessert werden. Das derzeitige Projekt zielt auf die Zugabe von Polyanilin (PANi) als Wirkstoff zur Verbesserung der Schichteigenschaften für die Erhöhung der Korrosionsbeständigkeit des Systems in stark salzhaltigen Medien bei höheren Temperaturen. T2 - GfKORR Jahrestagung CY - Frankfurt/Main, Germany DA - 07.11.2017 KW - Geothermie KW - Beschichtung KW - Korrosion PY - 2017 AN - OPUS4-43361 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Aristia, Gabriela A1 - Bäßler, Ralph A1 - Roth, C. T1 - SiO2-containing organic coatings for geothermal application N2 - Geothermal brine is considered to be an aggressive environment as it contains various dissolved salts. Even though carbon steel is commonly used as a construction material due to its machinability and economical reason, it is susceptible to uniform and localized corrosion in a high temperature and high pressure system. Therefore, a coating system is introduced to protect the carbon steel against corrosion in such environment. -It is necessary to find the optimum composition of SiO2 addition in the organic coatings to enhance the material performance, i.e. coatings adhesion, thickness optimization, thermal resistance. Current project aims at the addition of Polyaniline (PANi) as the active agent to improve the corrosion resistance of materials against a high saline medium at elevated temperatures. T2 - BAM PhD Day CY - Berlin, Germany DA - 21.09.2017 KW - Geothermal KW - Corrosion KW - Coating PY - 2017 AN - OPUS4-43362 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koerdt, Andrea A1 - Özcan Sandikcioglu, Özlem A1 - Wurzler, Nina T1 - Methanogenic Archaea N2 - Different environmental samples reveal that methanogenic Archaea are part of a multi-species biofilm on corroding metallic structures. Studies on microbial influenced corrosion (MIC) focus mainly on sulphate reducing Bacteria (SRB), leading to the assumption that they are exclusively responsible for metal corrosion. In fact, methanogenic Archaea are known to be involved in metal corrosion as well (e.g. Methanococcus maripaludis DSM 2067). In some cases SRB and methanogenic Archaea have comparable high corrosion rates. However, the underlying mechanisms causing corrosion are still unknown. The goal of this study is to develop suitable methods for analyzing two environmental isolates (M. maripaludis DSM 2067, M. maripaludis KA1) and two human-related isolates (Methanobrevibacter oralis and Methanobrevibacter smithii) for their ability to deteriorate/transform metals, which are relevant for technical and clinical applications. Moreover, the studies will provide essential information on the interaction mechanisms of human-related Archaea, which are frequently found in peri-implantitis, with dental material such as implants, crowns and bridges leading to their degradation and transformation. T2 - DECHEMA-GfKORR-Fachgruppe CY - Berlin, Germany DA - 04.10.2017 KW - Biofilm KW - Corrosion KW - Methanogens PY - 2017 AN - OPUS4-43025 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Raedel, Martina A1 - Bücker, Michael T1 - Research and reconstruction of historic gold mosaics N2 - A research project of reconstructing historical gold mosaics deals with reconstructing weatherproof gold and silver mosaics according to historical models. The gold mosaics examinded originate mainly from germany from 1880 to 1920 and are composed of three parts. They consist of a matching support glass, the gold or silver layer and a cover glass. By examining the morphology and layer thicknesses with the ESEM, and using chemical analysis with the EDX, the relationship of glass composition and damage patterns was established. The glass analysis provided quantitative composition data and made it possible to determine its chemical stability. It supplied the basis for calculating glass characteristics and was referred to when casting suitable historical mosaic glass. The analysis of the qualitative composition of the gold and silver layers also served as a model for reconstruction. After testing selected reconstructed gold mosaics in the climate chamber, the ESEM was used for capturing leaching and other process data and the glass composition was optimized accordingly. Over 100 predominantly historical gold mosaics were analyzed and the results entered into a database which can now be consulted for comparative investigations to determine both origin and date. T2 - What comes to mind when you hear mosaics, conserving mosaics from ancient to modern CY - Barcelona, Spain DA - 15.10.2017 KW - Gold mosaics KW - Leaching process KW - Composition KW - Database PY - 2017 AN - OPUS4-43216 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hiller, Th. A1 - Costabel, S. A1 - Müller-Petke, M. A1 - Kruschwitz, Sabine T1 - Evaluation of different laboratory NMR devices in a tripartite round robin test N2 - Nuclear magnetic resonance (NMR) is a well established laboratory / borehole method to characterize the storage and transport properties of rocks due to its direct sensitivity to the corresponding pore fluid saturation (water or oil) and pore sizes. For petrophysical applications there are several different NMR laboratory devices commercially available varying over a wide range of e.g. magnetic field strength / frequency (2 MHz to 30 MHz), applicable measurement protocols (T1, T2, T1-T2, T2-D, etc.) and sample sizes (2.5 cm to 10 cm in diameter). In this work we present NMR measurements, layed out in a round robin like manner, on a set of 20 sandstone samples. We use three different NMR devices containing two standard setups with homogenous magnetic fields (LIAG and RWTH) and one single-sided setup with gradient field (BGR) to measure T1 and T2 relaxation data. In our evaluation we especially focus on the comparison of the individually inverted relaxation time distributions to quantify the differences arising from different laboratory setups. Diverging results can be deduced on the one hand to the inherit differences between homogeneous and gradient fields but on the other hand also due to quality differences between the two homogeneous setups. Additionally, we also examine the influence of the individually chosen inversion parameters (signal processing, distribution sampling points, error weighting, regularization, etc.) to establish a general standardized best practice recommendation for future petrophysical NMR laboratory measurements. T2 - 77. Jahrestagung der Deutschen Geophysikalischen Gesellschaft CY - Potsdam, Germany DA - 27.03.2017 KW - Nuclear Magnetic Resonance KW - Sandstone PY - 2017 AN - OPUS4-43244 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Radunz, Sebastian A1 - Resch-Genger, Ute A1 - Soukka, T. T1 - Upconverting nanoparticle based assays and sensor systems for bacteria/biofilm detection N2 - Results of the short term scientific mission of Sebastian Radunz funded by the european upconversion network. T2 - Short term scientific mission CY - Turku, Finland DA - 09.01.2017 KW - Upconverting nanoparticles KW - Assays PY - 2017 AN - OPUS4-39328 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Yildirim, Arda A1 - Sentker, K. A1 - Huber, P. A1 - Schönhals, Andreas T1 - Structure, Dynamics and Phase Behavior of a Discotic Liquid Crystal Confined in Nanoporous Anodic Aluminum Oxide Membranes N2 - The interest in porous anodic aluminum oxide (AAO) has been rapidly growing due to its numerous applications in separation, catalysis, energy generation and storage, electronics, and sensors. From the scientific point of view, AAO is a topical interest in soft matter fields. Spatial confinement of soft matter in nanoporous media influences its structure, thermodynamics, and mobility. Embedding polymers and liquid crystals into nanopores of AAO results in a 2D nanoconfinement of these materials. This confinement affects their properties, compared to the bulk, such as phase transition temperatures and enthalpies, molecular mobility, and architecture of the crystallization. On the other hand, discotic liquid crystals (DLCs) are a promising class of soft matter for electronic applications. This is due to their ability to organize and stack themselves into columns in a hexagonal columnar mesophase, a mesophase in between the plastic crystalline and isotropic phase, driven by the overlap of the π orbitals of their aromatic core. This leads to a high charge-carrier mobility along the column axis. Further, these columns could then be considered as “molecular nanowires”. In this study, 2,3,6,7,10,11 hexakis[hexyloxy] triphenylene (HAT6), a triphenylene based DLC, was confined into nanoporous AAO membranes. The structure, dynamics and the phase behavior of the confined HAT6 were investigated by broadband dielectric spectroscopy (BDS) and differential scanning calorimetry (DSC). HAT6 was embedded into nanoporous AAO membranes by melt infiltration in the isotropic phase under argon atmosphere. The membranes have parallel aligned cylindrical nanopores, with pore diameter of 10, 20, 25, 40, 80, 120 and 180 nm. The filling degree for each sample was checked by thermogravimetric analysis (TGA) in order to ensure complete filling. Bulk HAT6 forms a hexagonal columnar phase; in between the isotropic phase above 371 K and the plastic crystalline phase below 340 K. Unlike the bulk, the confined HAT6 split the plastic crystalline-to-hexagonal columnar phase transition in two, which might be interpret as two different phase structures; close to the wall and at the pore center. Moreover, the isotropic-to-columnar transition of the confined HAT6 shifted, with decreasing pore diameter, to lower temperatures. Furthermore, pore surfaces of a series of membranes were chemically modified, resulting in a more hydrophobic pore surface than the unmodified ones. HAT6 was embedded into the modified membranes by the same aforementioned preparation. The influence of the changed host-guest-interaction, on the structure, dynamics, and the phase behavior of HAT6 confined in the modified membranes, was also investigated by BDS and DSC. T2 - 9th International Conference on Porous Media & Annual Meeting CY - Rotterdam, The Netherlands DA - 08.05.2017 KW - Nanoporous media KW - Anodic Aluminum Oxide KW - Discotic Liquid Crystal PY - 2017 AN - OPUS4-40089 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor A1 - Sturm, Patrick A1 - Lüchtenborg, Jörg A1 - Hlavácek, Petr A1 - Günster, Jens A1 - Kühne, Hans-Carsten T1 - Additive manufacturing of geopolymers by selective laser curing N2 - Additive manufacturing (3D printing) of ceramics and other materials offers significant advantages compared to conventional production processes for several applications. While ceramics have been extensively investigated in this regard, additive manufacturing of geopolymers have received much less attention to date. In the present contribution we study a ‘standard’ metakaolin-based geopolymer, a fly ash-based geopolymer and a silica-based one-part geopolymer regarding their suitability for additive manufacturing via selective laser curing. Model geometries such as bars and cuboids could be produced by this route. After selective laser curing the specimens were additionally cured at 80 °C for 24 h. The specimens were studied by means of scanning electron microscopy (SEM) and powder X-ray diffraction (XRD). SEM showed that the precursors in all geopolymers had reacted partially and geopolymeric gel had formed. XRD confirmed these results and additionally revealed that the crystalline byproducts (zeolites) in the one-part geopolymer differed from the byproducts observed in conventionally produced samples. This indicates that also the geopolymerization reactions differ between the two synthesis routes. The mechanical strength after selective laser curing and 80 °C-curing appeared to be highest for the metakaolin-based geopolymer. However, SEM also showed that a significant volume of macropores remained in most regions of all specimens, while some regions in the metakaolin-based geopolymer appeared to be significantly denser. These preliminary results demonstrate that selective laser curing offers potential for the production of geopolymers, but more research has to be undertaken to optimize the process. T2 - 92. DKG Jahrestagung CY - Berlin, Germany DA - 19.03.2017 KW - Geopolymers KW - Inorganic polymers KW - Additive manufacturing KW - 3D printing KW - Selective laser curing PY - 2017 AN - OPUS4-39514 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erdmann, Maren A1 - Niebergall, Ute A1 - Böhning, Martin A1 - Sameith, Janin T1 - Effect of surface degradation on high-density polyethylene for biofilm formation N2 - Renewable resources become more and more relevant to maintain energy demands for an increasing global population. Biosynthetic fuels like biodiesel might replace conventional petrochemical fuels. In this study the influence of microbial growth on biodiesel and diesel on the storage tank systems were investigated. Polymeric fuel storage tanks for diesel and biodiesel provide suitable environmental conditions for a broad spectrum of fungi and various bacteria, including cyanobacteria and aerobic heterotrophic, and even anaerobic, fermentative Bacteria. However, the questions whether and how ageing of the materials is affected by biofouling processes have not been answered so far. Therefore, a model system for biofilm formation was established to study the initial attachment phase of bacteria in dependency of ageing, quality and surface modification of thermoplastic polymers used for storage tank systems. The microbial survey is closely connected with a detailed characterization of the material’s properties and its ageing processes. A widely applied plastic used for fuel storage tanks is high-density polyethylene (PE-HD), which is available with various additives to increase UV-light stability and even for the storage of biodiesel. These materials were aged under UV-light and temperature using a defined climate chamber set-up. Further, the repeated filling of fuels was mimicked for such storage tanks, as this has an important impact on the life-cycle length for the storage Container. The aged polymers showed a significant change in the material’s characteristics, including surface characteristics (e.g. hydrophobicity) and carbonyl groups. The effect of the changed material properties on the biofilm formation are studied using bacterial isolates, previously obtained from a “dieselpest”, and as a model-reference E. coli. The unaged polymers showed already some significant differences for the initial attachment of E. coli K12. Polyethylene with additives was colonized faster than the reference material (without additives) although the final biofilm coverage was not impaired. Likewise, the settlement of a kerosene-isolated Bacillus species on the unaged materials independently of additives was only minor interfered. In future, our results should give stakeholders in industry and public authorities a better estimation of the life-cycle security for fuel storage tank systems and on the fuel quality. Further, our results could help to test and develop new materials or additives to prevent biofouling processes. T2 - VAAM Jahrestagung CY - Würzburg, Germany DA - 05.03.2017 KW - PE-HD KW - Biofilm KW - MIC KW - Degradation PY - 2017 AN - OPUS4-39457 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nützmann, Kathrin A1 - de Oliveira Guilherme Buzanich, Ana A1 - Radtke, Martin A1 - Reinholz, Uwe A1 - Stephan-Scherb, Christiane A1 - Emmerling, Franziska T1 - Depth dependent phase identification of corrosion zones in ferritic alloys by micro-X-ray absorption near edge structure spectroscopy N2 - Ferritic steels with chromium contents up to 13 wt% are used as materials for power plant components as boiler materials (< 2 wt% Cr) and super heater tubes (> 9 wt% Cr). These materials are subject to aggressive corrosion caused by hot gases such as CO2, H2O, O2 and SO2. Especially SO2 causes fatal corrosion even as a minor component. To examine sulfurous corrosion mechanisms, experiments with pure SO2 were conducted. A proper analysis of the material changes requires phase identification and quantification with a high lateral resolution within the corrosion scale. T2 - ANAKON2017 CY - Tübingen, Germany DA - 03.04.2017 KW - Corosion KW - Steel KW - XANES PY - 2017 AN - OPUS4-40415 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Welter, T. A1 - Deubener, J. A1 - Reinsch, Stefan A1 - Marzok, Ulrich A1 - Müller, Ralf T1 - Glass structures with low helium and hydrogen permeability N2 - An efficient energy provision using fuel cells is linked to effecitve hydrogen storage capabilities. Because of its low intrinsic hydrogen permeability, glass has a huge potential in modern concepts of hydrogen storage. Previous studies on oxidic glasses showed an empirical connection between glass composition and gas permeation, which was mainly derived from the behavior of silica glass. In this study we focus on the relationship between topologic (free volume; network polymerization) and thermodynamic (configurational entropy) parameters. The comparison of three glasses within the meta (earth-) alkaline alumino silicate system to silica glass shows that an increase of the atomic packing factor (APF) does not necessarily decrease the permeability. Furthermore, the results suggest a connection between ΔCp at Tg and hydrogen permeability of the glass. All experiments were performed assuming that chemical hydrogen solubiltity in glass is negligible at temperatures well below the glass transition temperature. T2 - 91. Glastechnische Tagung CY - Weimar, Germany DA - 29.05.2017 KW - Hydrogen permeability KW - Glass composition KW - Atomic packing factor KW - Configurational entropy KW - Diffusion coefficient PY - 2017 AN - OPUS4-40488 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schadow, Florian A1 - Gaal, Mate A1 - Bartusch, Jürgen T1 - Sende-Empfangs-Prüfköpfe auf Ferroelektret-Basis für Luftultraschall-Anwendungen N2 - Leichtbaustrukturen aus Verbundwerkstoffen stellen einen immer größeren Anteil im Flugzeug- und Automobilbau dar. Hiermit steigt die Nachfrage nach zuverlässigen, zerstörungsfreien Prüfmethoden, welche an solche Strukturen angepasst sind. Besonders Luftultraschall (LUS) eignet sich für diese Aufgabe, da hier kein Koppelmedium benötigt wird. Derzeit wird für diese Methode jedoch oft ein beidseitiger Bauteilzugang für eine Prüfung in Durchschallung vorausgesetzt. Handelsübliche Prüfköpfe für Luftultraschallanwendungen nutzen zudem meist Anpassschichten um den Impedanzunterschied zwischen Schwinger und Luft zu reduzieren. Sowohl Signal-Rausch-Abstand als auch die Bandbreite der resultieren-den Prüfköpfe ist für viele Anwendungen jedoch nicht ausreichend. Durch den Einsatz von Ferroelektreten wie zellulärem Polypropylen (zPP) kann hingegen vollständig auf Anpassschichten verzichtet werden. Hierbei handelt es sich um polarisierte, zelluläre Polymerschichten mit sehr geringer Dichte, Steifigkeit und Schallgeschwindigkeit. In diesem Beitrag stellen wir drei verschiedene Sende-Empfangs-Prüfköpfe vor, welche auf zellulärem Polypropylen basieren. Anhand von Schallfeld, Signal-Rausch-Abstand und Sendepegel werden diese Prüfköpfe charakterisiert. Die Ergebnisse werden mit den Ergebnissen von Referenzprüfköpfen ohne Sende-Empfangs-Charakteristik verglichen. Bei den Referenzprüfköpfen werden sowohl handelsübliche LUS-Prüfköpfe, sowie bisher entwickelte Prüfköpfe aus zellulärem Polypropylen berücksichtigt. T2 - DGZFP Jahrestagung 2017 CY - Koblenz, Germany DA - 22.05.2017 KW - Sende-Empfangs Prüfkopf KW - Ferroelektret KW - Zelluläres Polypropylen KW - Charakterisierung KW - Luftultraschall PY - 2017 AN - OPUS4-40430 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Torge, Manfred A1 - Feldmann, Ines A1 - Tagle, R. T1 - SEM and Micro-XRF analysis to investigate stained glass windows N2 - Several restoration projects of stained-glass windows have been performed in Poland since 2010.Chemical analysis of glass samples was performed with SEM/EDX on a FEI ESEM-XL 30, (EDX-EDAX) and with Micro-XRF (M4 Tornado, Bruker).The chemical composition of medieval glass samples and of glass samples of the 19th Century have been determined. T2 - Technart2017 CY - Bilbao, Spain DA - 02.05.2017 KW - SEM KW - Micro-XRF KW - Glass composition PY - 2017 AN - OPUS4-40435 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weltschev, Margit A1 - Schwarzer, Stefanie A1 - Eiben, Mario T1 - Suitable test method for the determination of the environmental stress cracking behaviour of polyethylene terephthalate as material for dangerous goods packagings N2 - The chemical industry has expressed great interest in using polyethylene terephthalate (PET) as material for packagings for the transport of dangerous goods. Due to the high strength and stiffness of PET, the wall thickness and weight of packagings can be reduced. The aim of this work was to find a laboratory test method for the determination of the stress cracking resistance of PET. One test method is the Full Notch Creep Test (FNCT), which was developed for polyethylene (PE) and is described in the standards EN ISO 13274 and EN 15507. It was investigated whether testing specimens made of PET with a full coplanar notch around the middle of the specimens show weakening after the impact of a tensile force in a wetting solution at 50°C. Unfortunately, this method couldn’t be used for PET because the specimens broke during notching due to the high brittleness of PET. The molding of the sheets and the following temper process for twelve hours are very time-consuming, Another possibility is laid down in BAM’s Dangerous Goods Rule BAM-GGR 015. This test was carried out with 1l PET bottles, which were filled with a 5% wetting solution and mounted with a clamping tool for 28 days at 40°C. Tensile test specimens were cut out afterwards from the middle of the bottles in the deformed areas. The tensile properties of the PET specimens couldn’t be determined due to the hardness of the material. In conclusion, the only way to provide information about the stress cracking resistance of PET was to perform stacking tests with PET design types of packagings. 1l bottles made of PET were filled with a 5% wetting solution and stored with a stacking load for 28 days at 40°C according to EN ISO 16495. The test bottles of PET passed the stacking tests. T2 - Fifth International Symposium Frontiers in Polymer Science CY - Seville, Spain DA - 17.05.2017 KW - Polyethylene terephthalate KW - Stress cracking resistance KW - Laboratory method KW - Dangerous goods packaging PY - 2017 AN - OPUS4-40438 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Marzok, Ulrich A1 - Müller, Ralf A1 - Gaber, Martin A1 - Reinsch, Stefan A1 - Welter, T. A1 - Deubener, J. T1 - Measurement of H2 permeability of glasses with VHE powder method N2 - The development of glassy hydrogen barriers requires the determination of low H2 permeabilities. Previous studies and numerical simulations have shown that the VHE powder method (vacuum hot extraction with mass spectrometric gas detection) is suitable for this purpose. The measured isothermal gas emission is fitted to a classical diffusion model for spherical particles from which the diffusion coefficient of the glass is calculated. The H2 permeability is determined by means of the solubility determined from the same measurement data. This presentation is referring to the optimization of the method regarding sample preparation and measurement data evaluation using suitable experimentally determined particle size distributions is reported. For quartz glass, it is shown that the accuracy of classical measuring methods is achieved with the VHE powder method. Furthermore, other examples of substantially gas-tighter glasses are given. T2 - 91. Glastechnische Tagung CY - Weimar, Germany DA - 29.05.2017 KW - Hydrogen permeation KW - Glass KW - Vacuum hot extraction KW - Powder method KW - Diffusion coefficient PY - 2017 AN - OPUS4-40441 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Marzok, Ulrich A1 - Müller, Ralf A1 - Reetz, R. A1 - Lauven, G. T1 - 3D High-temperature laser profilometry during sintering N2 - Most crucial for components of complex shape or heterogeneous micro structure, precise control of sintering has decisive influence on dimensional accuracy, mechanical integrity and reliability of sintered components. In these cases, only in situ 3D high-temperature shape screening during shrinkage would allow revealing temporary sinter warpage and hereby caused potential defects. Against this background, nokra Optische Prüftechnik und Automation GmbH, HTM Reetz GmbH and BAM developed a testing device for in situ 3D shape screening for ceramic and glass-ceramic tapes up to 1000°C by means of high-temperature laser profilometry. The local repeatability of the sample-sensor distance (sample height profile) is 10 µm at 1000°C. Current work is focused on dropping these restrictions in sample shape and temperature. In a second testing device, currently being in development, samples up to 5 cm x 5 cm x 5 cm can be measured at temperatures up to 1500°C.The presentation illustrates the current state of this work and possible applications of the method. T2 - 92. DKG Jahrestagung CY - Berlin, Germany DA - 19. 03. 2017 KW - Laser profilometry KW - 3D High-temperatue shape screening KW - Sintering PY - 2017 AN - OPUS4-40449 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thiede, Tobias A1 - Mishurova, Tatiana A1 - Cabeza, Sandra A1 - Kromm, Arne A1 - Nadammal, Naresh A1 - Bode, Johannes A1 - Bruno, Giovanni T1 - Residual stress analysis in selective laser melted parts of superalloy IN718 N2 - Additive Manufacturing (AM) by Selective Laser Melting (SLM) offers ample scope for producing geometrically complex parts in comparison to the traditional subtractive manufacturing strategies. Developing during the manufacturing process, residual stresses may limit the application of SLM parts by reducing the load bearing capacity as well as induce unwanted distortion depending on the boundary conditions specified in manufacturing. The present study aims to evaluate the bulk residual stresses in SLM parts by using neutron diffraction measurements performed at E3 line -BER II neutron reactor- of Helmholtz-Zentrum für Materialien und Energie (HZB) Berlin. Together with microstructure characterization and distortion measurements, it is possible to describe the stress state throughout the whole sample. The sample was measured in as-build condition (on a build plate) and after releasing from the build plate. The used material is the nickel based superalloy 718. This alloy is widely used in aerospace and chemical industries due to its superior corrosion and heat resistant properties. Obtained results indicated different residual stress states for each of the transversal, longitudinal and normal component. The normal and transversal component exhibits a rather compressive behavior while the longitudinal was tensile in the center part of the sample and became compressive towards the tip. As expected, the absolute values of all stress components decreased after releasing the sample from the building plate. A surface scan utilizing a coordinate-measuring machine (CMM) allowed us to present top surface distortion before and after releasing. The top surface showed a distortion around ±80µm after releasing. Microstructure evolution in the scanning-building cross-section is largely dominated by columnar grains. In addition, many small random orientated grains are prominent in the regions of a laser overlap during SLM. In summary, for the sample of superalloy 718 manufactured by SLM, a small distortion occurred when removing the sample from the build plate whereby the residual stress state decreases. Moreover, the observed columnar grains in the building direction could give a reason for the lowest stress values in that normal direction. However, the most important parameter controlling the residual stresses is the temperature gradient. Hence, future investigations are planned for a different scan strategy to distribute the laser impact in a more homogenous manner. T2 - 19th HERCULES Specialized Course CY - Grenoble, France DA - 15.05.2017 KW - Additive manufacturing KW - Selective laser melting KW - Residual stresses KW - Distortion KW - Microstructure PY - 2017 AN - OPUS4-40388 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kabelitz, Anke A1 - Dinh, Hoang An A1 - Emmerling, Franziska T1 - A02: Time-resolved WAXS studies on the crystallization of Al13 keggin clusters N2 - Polynuclear aluminium species (Al13 keggin cluster) find application in different areas like water purification, contaminant transport, and as pilling clays with high specific surface areas, due to their strong binding ability to aggregates and high positive charge. In the present contribution, we report on the in situ investigation of the Al13 sulfate synthesis by synchrotron wide-angle X-ray scattering (WAXS). Al13 cluster were crystallized by precipitating hydrolyzed aluminum solutions by the addition of sodium sulfate. The measurements were performed using a custom-made acoustic levitator as sample holder. The study provides information about the intermediates during the crystallization process. From the data, a mechanism was derived indicating the influence of the crystallization process. T2 - International Symposium of the CRC 1109 CY - Berlin, Germany DA - 19.02.2017 KW - WAXS KW - In situ KW - Crystallization PY - 2017 AN - OPUS4-39367 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Woydt, Mathias A1 - Mohrbacher, H. A1 - Vleugels, J. A1 - Huang, S. T1 - Potentials of niobium carbide (NbC) as cutting tools and for wear protection N2 - Niobium is today largely available. NbC grades displayed lower dry sliding friction over WC grades. The softer Ni- and NiMo-bondes NbC1.0-grades have a higher abrasive wear resistance (ASTM G65), even with lower toughnesses, as the tougher WC-Co grades. T2 - 19. Plansee Seminar CY - Reutte, Austria DA - 29.05.2017 KW - Niobium carbide (NbC) KW - Cutting tools KW - Hardness PY - 2017 AN - OPUS4-40512 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wäsche, Rolf A1 - Steinborn, Gabriele A1 - Woydt, Mathias T1 - Colloidal processing of metal bonded niobium carbide (NbC-Ni) N2 - The manufacturing of NbC with Ni binder with addition of titanium carbide by using a colloidal process for blending the different powders without a milling step were investigated. The the sintering process and formation of the resulting microstructures, the phase relations and the hardness of the produced cermet materials are characterized. T2 - 19. Plansee Seminar CY - Reutte, Austria DA - 29.05.2017 KW - Niobium carbide (NbC) KW - Cermets KW - Hardness PY - 2017 AN - OPUS4-40513 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wagner, Sabine A1 - Carrasco, S. A1 - Benito-Peña, E. A1 - Moreno-Bondi, M. C. A1 - Rurack, Knut T1 - Detection of antibiotics by combining fiber-optic array with microparticles coated with fluorescent molecularly imprinted polymers N2 - The widespread use of antibiotics in livestock farming leads to trace residues in food products and wastewater, potentially entailing antimicrobial resistance in food-borne pathogens. The determination of antibiotics in aqueous environments and foodstuff is thus of major concern. We have been developing optical sensors based on molecularly imprinted polymers (MIPs) due to the low production costs, stability, format adaptability and the possibility to imprint and thus their ability to recognize a wide variety of target analytes. As a fluorescently responding moiety in the polymer matrix a tailor-made fluorescent indicator cross-linker for direct transfer of the binding event into an optical signal was used. If such a cross-linker is integrated into a thin MIP-shell on microspheres such core/shell particles can be readily used in advanced multiplexing sensory fiber-optic microarrays. Here, we propose such a fiber-optic microarray based on fluorescent MIP microspheres for antibiotics. The binding behavior and the selectivity of a microarray using these silica core/MIP shell beads were examined and compared with a non-imprinted polymer (NIP) control, employing the target molecules and other structurally closely related antibiotics. T2 - APME2017 CY - Ghent, Belgium DA - 21.05.2017 KW - Molecularly imprinted polymers KW - Multiplexing sensory fiber-optic microarrays KW - Antibiotics PY - 2017 AN - OPUS4-40583 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Torge, Manfred A1 - Feldmann, Ines A1 - Knabe, Nicole A1 - Toepel, J. T1 - Organic surface coatings on medieval stained glass and microbiological investigation N2 - Mediaeval stained glass has been treated with Polymethylmetacrylate coatings by Kwiatkowski in Poland during the 1950th. Such treated panels were found in the Johannis Church of Toruń (without protective glazing), in the Cathedral of Włocławek (behind a protective glazing), and on glass kept in exhibition cases in the museum of Toruń. Surface coatings have been detected and analyzed. There was no extensive contamination by fungi or bacteria if the glass was either coated or not. T2 - Glass Science in Art and Conservation 2017 CY - Lisbon, Portugal DA - 06.06.2017 KW - Microbiological investigation KW - Medieval stained glass KW - SEM analysis PY - 2017 AN - OPUS4-40573 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Uhlmann, E. A1 - Kropidlowski, K. A1 - Woydt, Mathias A1 - Sammler, F. T1 - Cutting tools made from niobium carbide N2 - The Federal Institute for Materials Research and Testing (BAM) and the Institute for Machine Tools and Factory Management (IWF) of the Technical University Berlin analyzed the suitability of various NbC types in comparison to tungsten carbide (WC) for use as a tool in cutting processes. The focus was placed on the optimization of the functional profile of NbC-based cutting materials with reproducible industrial production. T2 - 19. Plansee Seminar CY - Reutte, Austria DA - 29.05.2017 KW - Niobium carbide (NbC) KW - Tungsten carbide (WC) KW - Cutting material PY - 2017 AN - OPUS4-40515 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Taparli, Ugur Alp A1 - Jacobsen, L. A1 - Griesche, Axel A1 - Michalik, K. A1 - Mory, D. A1 - Kannengießer, Thomas T1 - Time- and space-resolved in situ LIBS measurements of chemical compositions during TIG-welding N2 - An in situ monitoring of chemical compositions in the weld pool and the heat affected zone (HAZ) can enable the control of the welding process through the regulation of the welding parameters, and thus can prevent possible weld defects. The most critical parameter for hot cracking -from a metallurgical point of view- is the chemical composition of the weld pool. Chemical composition can be measured and quantified during the welding process with the LIBS technique having the appropriate calibration measurements. T2 - ICWAM 2017 CY - Metz, France DA - 17.05.2017 KW - Chemical compositions KW - TIG-welding KW - In situ measurement KW - LIBS PY - 2017 AN - OPUS4-40313 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schulz, Bärbel A1 - Rabe, Torsten A1 - Salehi, Mahdi T1 - High-temperature stability of ceramic springs N2 - Metallic springs undergo oxidation and creep at elevated temperatures and their use is limited to temperature of about 650°C. Therefore, there is a need for stable materials which can easily withstand temperatures up to 1000°C for long periods in different atmospheres. Ceramic materials have been drawing attention due to their excellent properties. This work aimed at investigating the high-temperature stability of zirconia and alumina ceramic springs at elevated temperatures under different atmospheres (air, N2 and H2) in order to determine the limitation of use of these ceramic springs. T2 - DKG 2017 CY - Berlin, Germany DA - 20.03.2017 KW - Ceramic spring KW - High-temperature stability KW - Harsh environments KW - Spring constant PY - 2017 AN - OPUS4-40289 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kotschate, Daniel A1 - Gohlke, Dirk A1 - Meinig, Silvia A1 - Kaszemeikat, T. T1 - Hochauflösende Reinheitsgradbestimmung – Fertigung von Referenzfehlern N2 - Regelwerke zur zerstörungsfreien Bestimmung des Reinheitsgrades wie das SEP 1927 und die ASTM E588 erreichen ihre Vergleichbarkeit unter Anwendung von - vergleichsweise einfachen - Referenzfehlern. Hinsichtlich Realisierbarkeit wird somit der Kompromiss zwischen Herstellung des Referenzfehlers und der erreichbaren Nachweisgrenze gefunden. Zur Weiterentwicklung über die Grenzen der SEP1927 hinaus, wurde der Versuch unternommen Fehler kleiner 500 μm herzustellen - welche aufgrund der geringen geometrischen Ausdehnung fertigungsbedingt schwierig zu realisieren sind. Bei den vergleichenden Untersuchungen kristallisierten sich zwei Fertigungsverfahren, Funkenerosion (EDM: electrical discharge maching) und die Fertigung der Bohrungen unter Verwendung eines Hochleistungslasers, als vielversprechend heraus. Zunächst wurden die Fehler mit beiden Verfahren in unterschiedlichen Größen (100, 250 und 100 μm) und Tiefen (1, 1,5 und 2 mm) unter Anwendung von computertomographischen Verfahren der Röntgenprüfung, die Geometrie der eingebrachten Fehlstellen und anschließend durch hochauflösende Tauchtechnikmessungen das Reflektionsverhalten charakterisiert. T2 - DGZfP Jahrestagung CY - Koblenz, Germany DA - 22.05.2017 KW - Materialcharakterisierung KW - Reinheitsgradbestimmung KW - Ultraschalltauchtechnik PY - 2017 AN - OPUS4-40353 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Czarnecki, Sebastian A1 - Hackelbusch, Sebastian A1 - Bertin, Annabelle T1 - Synthesis of hybrid inorganic/organic homopolymers via ATRP and RAFT: A practical comparison N2 - The synthesis of hybrid inorganic/organic copolymers, using reversible deactivation radical polymerization (RDRP) techniques, has been an intensively studied research topic over recent years. A plethora of hybrid inorganic/organic copolymers were synthesized, including hybrid inorganic/organic block copolymers as well as random copolymers,[1–4] that showed great potential in fabricating hybrid (nano)materials with tailored properties [5]. Two widely employed RDRP techniques to prepare such hybrid inorganic/organic copolymers are atom transfer radical polymerization (ATRP) [1,2] and reversible addition-fragmentation chain transfer (RAFT) polymerization [3,4]. In order, to afford hybrid inorganic/organic copolymers with narrow dispersity, high conversions and precise structures, it is required to choose proper reaction conditions. Due to the importance of both ATRP and RAFT in the preparation of such hybrid polymers, we aim to compare both RDRP techniques by preparing 2-acetoxyethyl methacrylate (AcEMA) and 3-(triethoxysilyl)propyl methacrylate (TESPMA) based homopolymers. For this purpose, AcEMA and TESPMA were polymerized in 1,4-dioxane at 60 °C mediated by CuBr/N,N,N',N'-pentamethyldiethylenetriamine (PMDETA) and 2-(2-carboxylethylsulfanylthiocarbonyl-sufanyl) propionic acid (TTC) as well as cumyl dithiobenzoate (CDB) to evaluate the suitability and reliability of ATRP and RAFT to prepare such hybrid (co)polymers. T2 - Berlin Chemie Symposium 2017 CY - TU Berlin, Berlin, Germany DA - 06.04.2017 KW - Hybrid inorganic/organic copolymers KW - ATRP KW - RAFT PY - 2017 UR - https://bcs.jcf-berlin.de/BCS2017/BoA2017.pdf AN - OPUS4-40280 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stegemann, Robert A1 - Cabeza, Sandra A1 - Lyamkin, Viktor A1 - Pelkner, Matthias A1 - Wimpory, Robert A1 - Boin, Mirko A1 - Pittner, Andreas A1 - Kreutzbruck, Marc A1 - Bruno, Giovanni T1 - Evaluation magneto-mechanischer Effekte in hochauflösenden Magnetfeldmessungen durch Neutronendiffraktion N2 - Die mechanische Spannung ist ein maßgeblicher Parameter ferromagnetischer Materialien. Wird ein solches Material unter die Curie Temperatur abgekühlt, zerfällt es spontan in nahezu selbstgesättigte magnetische Domänen. Diese Magnetisierung führt gleichzeitig zu einer Verformung der mit ihr gekoppelten Kristallgitter. Ein Effekt der auch reziprok gilt: wird die Gitterverformung durch eine Spannung behindert ändert sich zwangsweise der magnetische Zustand. Man kann annehmen, dass zwischen unterschiedlichen, für sich aber homogen verspannten Werkstoffbereichen, lokale magnetische Streufelder auftreten, weil magneto-mechanische Effekte eine Inkompatibilität der Domänenstruktur induzieren. Bekanntlich bilden sich Spannungsgradienten nach Schweißprozessen durch ungleichmäßigen Wärmeeintrag, thermischer Dehnung, und unterschiedlichen Abkühlraten aus. Unter dieser Prämisse untersuchen wir Wolfram-Inertgas geschweißte Blindnahtproben (250x100x4,8 mm^3) aus einem hypereutektoiden Baustahl. Der Spannungszustand der Proben wurde anhand von Neutronendiffraktometrie (ND) am Instrument E3 am Reaktor BERII (Helmholzzentrum Berlin, HZB) charakterisiert. ND ist ein Referenzverfahren für die quantitative Bestimmung von elastischen Dehnungen in kristallinen Materialien, deren Gitter selbst der Messmaßstab ist. Die Auswertung zeigt hohe Längsspannungen mit lokalen Maxima in Größenordnung von 600 MPa, die von umgebenen Druckspannungszonen kompensiert werden. Zur Detektion der magnetischen Kleinststreufelder verwenden wir speziell designte GMR-Sensorik (GMR - Giant Magneto Resistance), die aufgrund der geringen Größe ihrer aktiven Sensorelemente hohe Ortsauflösung mit Sensitivität vereint. Die Visualisierung der Messergebnisse lässt eine klare magnetische Mikrostruktur der Schweißnähte erkennen, in der die Streufelder lateral in Größenordnung des Erdmagnetfeldes variieren (~50 µT). Wir zeigen durch einen Vergleich beider Messverfahren, dass lokale magnetische Streufeldmaxima in hohem Maße mit den Spannungsgradienten übereinstimmen. T2 - DGZfP-Jahrestagung CY - Koblenz, Germany DA - 22.05.2017 KW - WIG-Blindschweißnaht KW - GMR-Sensorik KW - Neutronendiffraktion KW - Eigenspannungen PY - 2017 AN - OPUS4-40370 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wiesholler, L. M. A1 - Grauel, Bettina A1 - Himmelstoß, S. A1 - Würth, Christian A1 - Resch-Genger, Ute A1 - Baeumner, A. J. A1 - Hirsch, T. T1 - Core-shell- Nd3+ - doped upconversion nanoparticles with enhanced luminescence properties for bioanalytical applications N2 - Upconversion nanoparticles are characterized by their ability to convert low energy near-infrared excitation in high energy emissions in the visible range. This is enabled by sequential absorption of two or more photons via energy transfer from the sensitizer lanthanide ion Yb3+ to an activator lanthanide ion, e.g. Er3+. Yb3+ sensitation has the advantage of 980 nm excitation achieved by commercial available low power cw laser modules. Nevertheless, for some applications, especially in aqueous media, which is predominantely in bioanalytical applications, there is the drawback of a local Absorption maximum of water at this wavelength. Sample heating can occur, and excitation power density is strongly distance dependent. To overcome this issue, the idea is to shift the excitation wavelength to 808 nm. This can be achieved by a tandem-excitation using Nd3+ and Yb3+ ions. Nd3+ gets excited by 808 nm irradiation and transfers the energy to Yb3+, which triggers the upconversion emission of the Er3+ ions. Therefore, it is mandatory to separate Nd3+ and Er3+ by core-shell architecture for reducing the energy backtransfer from Er3+ to Nd3+. To further enhance the upconversion luminescence an additional inert shell formed by the host material NaYF4 reduces the quenching effects caused by surface defects and dangling bonds. T2 - MRS Spring Meeting CY - Phoenix, Arizona, USA DA - 17-21. April KW - Core-shell KW - Upconversion KW - Nd3+ PY - 2017 AN - OPUS4-40035 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sentker, Kathirn A1 - Yildirim, Arda A1 - Lippmann, M. A1 - Hoffmann, T. A1 - Seeck, O. A1 - Kityk, A. A1 - Schönhals, Andreas A1 - Huber, Patrick T1 - Fabrication of organic nanowires by melt infiltration of a discotic liquid crystal: A combined X-ray diffraction and optical birefringence study N2 - Optical polarimetry and angle dependent X-ray scattering in employed to study the structure of a discotic liquid crystal confined into nanochannels. The pore size dependence of the obtauned data are discussed in detail. T2 - DPG Spring Meeting 2017 CY - Dresden, Germany DA - 20.03.2017 KW - Discotic Liquid Crystals KW - Nanoconfinement PY - 2017 AN - OPUS4-39591 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Genga, R. M. A1 - Cornish, L. A. A1 - Rokebrand, P. A1 - Glaser, D. A1 - Woydt, Mathias A1 - Janse van Vuuren, A. A1 - Polese, C. T1 - Microstructure and wear behavior of improved NbC cermets for (BS-1452) grey cast iron machining N2 - Tungsten carbide (WC) and cobalt (Co) based cermets are the most successful commercial cermets beacuse of the good combination of physical, mechanical and behavioral properties. Niobium carbide (NbC) has good mechanical and physical properties, such as high hardness, very high melting point and low density. SPS refined the NbC grains and increased the hardness, while substitution of Co with Ni improved the fracture toughness. T2 - 19. Plansee Seminar CY - Reutte, Austria DA - 29.05.2017 KW - Cermets KW - Grey cast iron machining KW - Tungsten carbide (WC) KW - Niobium carbide (NbC) KW - Wear PY - 2017 AN - OPUS4-40603 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eisermann, René A1 - Rohwetter, Philipp A1 - Hicke, Konstantin T1 - Reducing sensitivity fading in C-OTDR by use of enhanced scattering fiber segments N2 - We have shown that for C-ODTR based DAS two UV-inscribed scattering segments within an optical fiber have a significant influence on the local sensitivity Fading characteristics. This method was experimental proven to be suitable for distributed dynamic strain measurement in a thermally unstable environment. Signal-to-noise ratio analyses for detecting a signal peak within the time-dependent spectra were performed. Results show an increase in SNR and additionally that the occurrence of total loss of sensitivity (SNR <1) could be decreased by a factor of six when compared to an untreated standard fiber. T2 - 25th International Conference on Optical Fiber Sensors CY - Jeju-City, Jeju, Republic of Korea DA - 24.04.2017 KW - Coherent Rayleigh OTDR KW - Distributed acoustic sensing KW - Distributed vibration sensing KW - Fiber sensors KW - Quasi-distributed sensing KW - Rayleigh scattering PY - 2017 AN - OPUS4-40643 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Huang, S. G. A1 - Vleugels, J. A1 - Mohrbacher, H. A1 - Woydt, Mathias T1 - Effect of carbon content on the microstructure and mechanical properties of NbC-Ni based cermets N2 - The aim of this work was to correlate the carbon content in NbC-Ni starting powders with the resulting microstructure, hardness and fracture toughness of Ni-bonded NbC cermets. T2 - 19. Plansee Seminar CY - Reutte, Austria DA - 29.05.2017 KW - Cermet KW - Liquid phase sintering KW - Microstructure KW - Hardness KW - Carbon PY - 2017 AN - OPUS4-40647 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bruno, Giovanni A1 - Kupsch, Andreas A1 - Mueller, Bernd R. A1 - Lange, Axel T1 - X-ray refraction 2D and 3D techniques N2 - X-ray refraction techniques represent a very promising, yet not so wide-spread, set of X-ray techniques based on refraction effects. They allow determining internal specific surface (surface per unit volume) in a non-destructive fashion, position and orientation sensitive, and with nanometric detectability. While they are limited by the X-ray absorption of the material under investigation, we demonstrate showcases of ceramics and composite materials, where understanding of microstructural features could be achieved in a way unrivalled even by high-resolution techniques such as electron microscopy or computed tomography. T2 - ICTMS 2017 CY - Lund, Sweden DA - 26.06.2017 KW - X-ray refraction KW - Composites KW - Damage KW - Cracks KW - Cearmics PY - 2017 AN - OPUS4-41042 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lange, Thorid A1 - Hielscher, Stefan A1 - Hidde, Gundula A1 - Beck, Uwe T1 - Mehr-Proben-Kleb-Vorrichtung (MPKV) zur Validierung der Klebfestigkeit N2 - Mit der Verfügbarkeit der Mehr-Proben-Prüfung von bis zu 8 Klebverbunden mittels CAT-Technologie (CAT: centrifugal adhesion testing) wurde im Forschungsvorhaben OKTETT ein durchgehendes Mehr-Proben-Konzept zur Validierung der Klebfestigkeit angewendet. Dazu gehört ein universeller Probenteller (Abb.1) zur Mehr-Proben-Handhabung bei Vorbehandlung, Lagerung, Transport und Klebung. Für das Mehr-Proben-Kleben wurde die MSB-Technologie (MSB: multiple sample bonding) unter Verwendung einer instrumentierten hydraulischen Mehr-Proben-Kleb-vorrichtung entwickelt. Damit kann der Klebandruck für bis zu 8 Prüfkörper über einen Drucksensor definiert eingestellt und die gesamte Vorrichtung beim Kleben Temperaturen von bis zu 180°C ausgesetzt werden. T2 - 12. Thementage Grenz- und Oberflächentechnik (ThGOT) und das 5. Kolloquium Dünne Schichten in der Optik CY - Zeulenroda, Gemany DA - 14.03.2017 KW - Zentrifugentechnologie KW - Mehr-Proben-Kleben (MSB) KW - Mehr-Proben-Prüfen (CAT) KW - Haftfestigkeit KW - Verbundfestigkeit PY - 2017 AN - OPUS4-41291 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Piedada, F. M. A1 - Simöes, R. G. A1 - Bernardes, C.E.S. A1 - Joseph, A. A1 - Kraus, Werner A1 - Diogo, H. A1 - Emmerling, Franziska A1 - da Piedada, M. E. M. T1 - Polymorphism in Simvastatin: A Single Crystal X-ray Diffraction, Themodynamic, and MDSimulation Study N2 - Simvastatin is a prominent member of the statin family, a class of antilipidemic drugs widely used in the treatment of high plasma cholesterol levels, and thus in the prevention of atherosclerosis and cardiovascular diseases. Simvastatin is typically employed as a solid and it is well known that, in this case, the detection and characterization of polymorphism is of considerable importance. Polymorphs differ by their packing arrangements and also, occasionally, by the conformations of the molecules in the crystal lattice. These structural variations are normally reflected by differences in physical properties, such as solubility and dissolution rate in a given media, which may significantly affect the bioavailability of a drug. The lack of control of polymorphism can, therefore, play havoc with the safe use of a drug. T2 - COST Action CM1402 CY - Lincoln, United Kingdom DA - 26.06.2017 KW - Polymorphism KW - X-ry Diffraction PY - 2017 AN - OPUS4-41252 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Waurischk, Tina A1 - Balzer, R. A1 - Kiefer, P. A1 - Reinsch, Stefan A1 - Müller, Ralf A1 - Behrens, H. A1 - Deubener, J. T1 - New device for inert sub-critical crack growth: measurements in crystallized glasses N2 - Compared to its intrinsic strength, the practical strength of glasses is substantially lowered by microscopic flaws. Their sub critical growth from the surface is strongly affected by ambient humidity. A new device was designed to enable the observation of sub critical crack growth (SCCG) in vacuum and controlled atmosphere. It allows measurements in transparent and semi-transparent materials in double cantilever beam (DCB) geometry. The aim of the present work is to study the effect of crystals on crack growth. T2 - 12th International Symposium on Crystallization in Glasses and Liquids CY - Segovia, Spain DA - 10.09.2017 KW - Double cantilever beam KW - DCB KW - Crack intensity factor KW - Crack growth velocity KW - Glass KW - Glass ceramic PY - 2017 AN - OPUS4-41995 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreier, Andy A1 - Jeschke, T. A1 - Petermann, K. A1 - Wosniok, Aleksander A1 - Krebber, Katerina T1 - Analytical model for mode-based insertion loss in ball-lensed coupling of graded-index silica and polymer fibres N2 - Analytical model for ball-lensed couplers to calculate the insertion loss for each optical mode. The basis for the calculation are commercial perfluorinated polymer optical (PFGI-POFs) and silica based fibres (SOFs). The modal power distribution for given misalignments are presented as well as the reflection-based losses at all optical interfaces. Additionally, the ball-lensed interconnection between PFGI-POF and SOF was theoretically demonstrated. T2 - POF 2017: 26th International Conference on Plastic Optical Fibres CY - Aveiro, Portugal DA - 13.09.2017 KW - Polymer optical fibre KW - Optical connector PY - 2017 AN - OPUS4-41974 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kirner, Sabrina V. A1 - Spaltmann, Dirk A1 - Krüger, Jörg A1 - Bonse, Jörn T1 - Laser-induced periodic surface structures on steel for tribological applications N2 - Laser-induced periodic surface structures (LIPSS) can be generated by irradiation of almost any material with linearly polarized laser beams, particularly when using ultrashort laser pulses. Within this work, different types of steel were irradiated at optimized conditions for the processing of large surface areas. For these nanostructured surfaces, the coefficient of friction (COF) using different lubricants was determined and the corresponding wear tracks were characterized by scanning electron microscopy (SEM). Our experiments provide a qualification of the tribologicalperformance of the fs-LIPSS on different steel surfaces, which are relevant for technical applications. T2 - International Conference on Laser Ablation (COLA) CY - Marseille, France DA - 3.09.2017 KW - Femtosecond laser ablation KW - Laser-induced periodic surface structures (LIPSS) KW - Tribology KW - Friction and wear KW - Steel PY - 2017 AN - OPUS4-42358 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kirner, Sabrina V. A1 - Krüger, Jörg A1 - Bonse, Jörn T1 - LiNaBioFluid Laser-induced nanostructures as biomimetic model of fluid transport in the integument of animals N2 - Laser-induced Nanostructures as Biomimetic Model of Fluid Transport in the Integument of Animals”, aims on laser-fabrication of biomimetic surfaces with unique wetting properties, which are inspired by the hierarchical micro- and/or nano- structures of animal body surfaces. LiNaBioFluid is a Research and Innovation Action funded by the European Commissions’ Horizon 2020 - FET Open Programme, which supports early-stage research on any idea for a new technology (Grant Agreement no: 665337). It brings together 7 partners from 4 different countries and is strongly interdisciplinary combining renowned experts from the fields of zoology, physics, mechatronics, life sciences, materials sciences, laser-matter interaction, production technology, tribology, and biomimetics. www.laserbiofluid.eu/ T2 - Science Sets Sail CY - Baltic Sea DA - 2.08.2017 KW - Laser-induced periodic surface structures (LIPSS) KW - EU H2020 project KW - Biomimetics KW - Wetting KW - Tribology KW - Friction and wear KW - Laser ablation PY - 2017 AN - OPUS4-42359 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rosemann, Paul A1 - Müller, C. A1 - Modersohn, W. T1 - Einfluss der Schweißnaht-Nachbehandlung auf die Korrosionsbeständigkeit von nichtrostenden Duplexstählen N2 - Der Duplexstahl 1.4062 (X2CrNiN22-2) hat sich im Bauwesen als Werkstoffalternative zu den nichtrostenden Austeniten etabliert. Die Korrosionsbeständigkeit von Schweißverbindungen wird, neben dem Grundwerkstoff, dem Schweißzusatzwerkstoff und dem Schweißverfahren, auch sehr stark von der Oberflächennachbehandlung der Schweißnaht beeinflusst. Je nach zukünftigem Anwendungsbereich und geforderter Optik sowie Korrosionsbeständigkeit wird der Schweißnahtbereich anschließend geschliffen, gebeizt, elektropoliert, oder gestrahlt, um die beim Schweißen entstehenden Zunderschicht zu entfernen. Gestrahlte Oberfläche sind in der industriellen Praxis häufig anzutreffen, da sie deutlich einfacher und kostengünstiger herzustellen sind als gebeizte oder elektropolierte Oberflächen. Die Auswahl des Strahlmittels bestimmt auch die Prozesskosten, wobei das Strahlen mit Korund effektiver als das Strahlen mit Glasperlen ist. In den letzten Jahren wurden bei nichtrostenden Stählen korrosionsanfällige Oberflächen beobachtet, wenn diese mit Korund geschliffen wurden. Daher wird nun auch beim Strahlen kritisch hinterfragt, ob das Strahlmittel die Korrosionsbeständigkeit verändert. Diese Fragestellung wird beantwortet indem geschliffene, gebeizte, mit Korund gestrahlte und mit Glasperlen gestrahlte Schweißverbindungen vergleichend untersucht werden. Die Ergebnisse der REM-Untersuchungen von den Strahlmitteln und den gestrahlten Oberflächen werden dazu mit den Ergebnissen verschiedener Korrosionsuntersuchungen (KorroPad-Indikatortest, Potentialmessungen und Bestimmung der kritischen Lochkorrosionspotentiale) korreliert und vorgestellt. T2 - Werkstoffwoche 2017 CY - Dresden, Germany DA - 27.09.2017 KW - Duplexstahl KW - Korrosion KW - Nichtrostender Stahl KW - Oberflächenbearbeitung KW - Schweißen KW - Strahlen PY - 2017 AN - OPUS4-42830 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin A1 - Reinemann, Steffi A1 - Lehmann, Jens A1 - Burkert, Andreas T1 - Einfluss von Korundschleifprozessen auf die Korrosionsbeständigkeit nichtrostender Stähle N2 - Das Poster stellt aktuelle Eregbnisse des AiF-Vorhabens 18823 N/1 zum Einfluss von Schleifprozessen auf die Korrosionsbeständigkeit nichtrostender Stähle vor. T2 - Jahrestagung 2017 der GfKORR CY - Frankfurt a. M., Germany DA - 07.11.2017 KW - Korrosion KW - Corrosion KW - Korundschleifen KW - Corundum grinding KW - Nichtrostende Stähle KW - Stainless Steels PY - 2017 AN - OPUS4-42773 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rosemann, Paul A1 - Müller, C. T1 - Wärmebehandlung und Korrosionsbeständigkeit druckaufgestickter nichtrostender Stähle N2 - Gefüge und Eigenschaften nichtrostender Stählen werden maßgeblich von ihrer chemischen Zusammensetzung und der Wärmebehandlung bestimmt. Eine spezielle Werkstoffgruppe der austenitischen nichtrostenden Stähle enthält ca. 19 Gew.-% Mangan und 0,8 Gew.-% Stickstoff, um das austenitische Gefüge ohne das Legieren mit Nickel sicherzustellen. Die herausragenden mechanischen Eigenschaften dieser Werkstoffe (Rm von 900 2.000 MPa, A5 > 50 %, Av > 350 J) werden nach der Wärmebehandlung (Lösungsglühen und Abschrecken) durch gezielte Kaltverfestigung eingestellt. Das Lösungsglühen beseitigt vorhandene Kaltverfestigung und unerwünschte Ausscheidungsphasen (Cr2N, M23C6 und Sigma-Phase) und bewirkt die homogene Verteilung der Legierungselemente (insbesondere Stickstoff) im Austenit. Dies ist zur Erzielung der Korrosionsbeständigkeit von entscheidender Bedeutung. Im Poster werden systematische Untersuchungen zur Korrosionsbeständigkeit dieser vielversprechenden Werkstoffklasse vorgestellt und die Interaktion zwischen Legierungszusammensetzung, Wärmebehandlung, Gefüge und Korrosionsbeständigkeit dargestellt. Insbesondere der Einfluss von Warmauslagerungsversuchen nach dem Abschrecken wird dabei charakterisiert. Die vom Gefüge bedingten Veränderungen der Korrosionsbeständigkeit werden durch verschiedene Methoden (EPR, KorroPad, Lochkorrosionspotentiale) ermittelt und interpretiert. T2 - Werkstoffwoche 2017 CY - Dresden, Germany DA - 27.09.2017 KW - Wärmebehandlung KW - Korrosion KW - Nichtrostender Stahl KW - EPR KW - KorroPad KW - Sensibilisierung KW - Stickstoff KW - ThermoCalc PY - 2017 AN - OPUS4-42831 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dieck, S. A1 - Ecke, M. A1 - Harnisch, K. A1 - Rosemann, Paul A1 - Halle, T. T1 - Gefüge- und Phasenanalyse biokompatibler Co-Cr-Mo-Legierung N2 - Co-Cr-Mo-Werkstoffe sind im Bereich der Biomaterialien weit verbreitet und werden für Endoprothesen eingesetzt. Deren Lebensdauer ist jedoch durch tribologische und korrosive Dauerbelastung begrenzt. Um die Anzahl operativer Eingriffe am Patienten zu minimieren, ist es notwendig den Werkstoff hinsichtlich Verschleißbeständigkeit und Korrosionsbeständigkeit zu optimieren. Hierfür ist ein umfassendes Verständnis der legierungsabhängigen Phasenbildung und –entwicklung während Herstellung und Wärmebehandlung notwendig. An einer speziellen Co-Cr-Mo Legierung werden verschiedene Untersuchungen zur Gefügecharakterisierung durchgeführt. Dabei werden die auftretenden Phasen thermodynamisch berechnet, mittels XRD nachgewiesen, die Phasenmorphologie durch EBSD analysiert, die Elementverteilung durch EDX-Analyse ermittelt und die Ergebnisse durch Farbätzen verifiziert. Das Ziel der Untersuchungen ist es, Optimierungspotentiale bei Herstellung und Wärmebehandlung zu identifizieren. T2 - Werkstoffwoche 2017 CY - Dresden, Germany DA - 27.09.2017 DA - 29.09.2017 KW - CoCrMo KW - Gefüge KW - ThermoCalc KW - EBSD KW - Farbätzen PY - 2017 AN - OPUS4-42832 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, C. A1 - Rosemann, Paul T1 - Wärmebehandlung und Korrosionsbeständigkeit druckaufgestickter nichtrostender Stähle N2 - Gefüge und Eigenschaften nichtrostender Stählen werden maßgeblich von ihrer chemischen Zusammensetzung und der Wärmebehandlung bestimmt. Eine spezielle Werkstoffgruppe der austenitischen nichtrostenden Stähle enthält ca. 19 Gew.-% Mangan und 0,8 Gew.-% Stickstoff, um das austenitische Gefüge ohne das Legieren mit Nickel sicherzustellen. Die herausragenden mechanischen Eigenschaften dieser Werkstoffe (Rm von 900 2.000 MPa, A5 > 50 %, Av > 350 J) werden nach der Wärmebehandlung (Lösungsglühen und Abschrecken) durch gezielte Kaltverfestigung eingestellt. Das Lösungsglühen beseitigt vorhandene Kaltverfestigung und unerwünschte Ausscheidungsphasen (Cr2N, M23C6 und Sigma-Phase) und bewirkt die homogene Verteilung der Legierungselemente (insbesondere Stickstoff) im Austenit. Dies ist zur Erzielung der Korrosionsbeständigkeit von entscheidender Bedeutung. Im Poster werden systematische Untersuchungen zur Korrosionsbeständigkeit dieser vielversprechenden Werkstoffklasse vorgestellt und die Interaktion zwischen Legierungszusammensetzung, Wärmebehandlung, Gefüge und Korrosionsbeständigkeit dargestellt. Die vom Gefüge bedingten Veränderungen der Korrosionsbeständigkeit werden durch verschiedene Methoden ermittelt und interpretiert. T2 - GfKORR-Jahrestagung 2017 CY - Frankfurt a. M., Germany DA - 07.11.2017 KW - Wärmebehandlung KW - Korrosion KW - Nichtrostender Stahl KW - EPR KW - KorroPad KW - Sensibilisierung KW - Stickstoff KW - ThermoCalc PY - 2017 AN - OPUS4-42833 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kauss, N. A1 - Rosemann, Paul T1 - Sensibilisierungsverhalten vom nichtrostenden Lean-Duplexstahl 1.4062 N2 - Der nichtrostende Lean-Duplexstahl 1.4062 (X2CrNiN22-2) verbindet die hohe Festigkeit des Ferrits mit der Duktilität und Zähigkeit des Austenits in einem zweiphasigen Gefüge mit sehr hoher Korrosionsbeständigkeit. Die höchste Korrosionsbeständigkeit wird erreicht, wenn das ferritisch-austenitische Gefüge frei von weiteren Sekundärphasen ist. Dies wird durch ein gezieltes Lösungsglühen bei 1050 °C mit anschließender Abschreckung in Wasser erreicht. Durch thermische Beeinflussung (z.B. beim Schweißen) können Sekundärphasen ausgeschieden und die Korrosionsbeständigkeit des Werkstoffs gesenkt werden. Dies wurde durch eine isotherme Warmauslagerung bei 500 °C bis 900 °C für 0,1 h bis zu 72 h simuliert. Die Veränderung der Korrosionsbeständigkeit wurde mit dem DL-EPR-Verfahren und durch die angepasste KorroPad-Prüfung ermittelt. Die ermittelten Anfälligkeitsbereiche wurden miteinander Verglichen und in zwei Sensibilisierungsschaubildern zusammengefasst. T2 - GfKORR-Jahrestagung CY - Frankfurt a. M., Germany DA - 07.11.2017 KW - Duplexstahl KW - Nichtrostender Stahl KW - Wärmebehandlung KW - Korrosion KW - EPR KW - KorroPad KW - Sensibilisierung PY - 2017 AN - OPUS4-42834 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sahre, Mario A1 - Mitzkus, Anja A1 - Beck, Uwe A1 - Köppe, Enrico A1 - Bartholmai, Matthias A1 - Basedau, Frank A1 - Hofmann, Detlef A1 - Gong, Xin A1 - Schukar, Vivien T1 - Electroplated magnetostrictive actuator layer enabling the external diagnosis of strain sensors N2 - Embedded fibre-opticaloptical strain sensors are suitable for structural health monitoring. In order to validate long-term performance (e.g.sensors integrated in airplane wings or wind power turbine blades) an external diagnostics is required. A strain-detecting region of the optical fibre, the fibre Bragg grating (FBG, is encased by a magnetostrictive layer system serving as actuator. For the validation of the correct sensor function, an external magnetic field introduces mechanical strain resulting in a defined shift of the Bragg wavelength. The layer system is realized by acombined PVD /ECD process optimized regarding magnetostrictive and mechanical properties. The long -term stability of layer adhesion and actuator function has been verified. T2 - 12. Thementage Grenz- und Oberflächentechnik (ThGOT) und das 5. Kolloquium Dünne Schichten in der Optik CY - Zeulenroda, Germany DA - 14.03.2017 KW - Magnetostrictive actuator layer KW - PVD /ECD process KW - Magnetostrictive layer KW - Strain sensors PY - 2017 AN - OPUS4-41800 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dörfel, Ilona A1 - Nofz, Marianne A1 - Sojref, Regine A1 - Schulz, Wencke A1 - Saliwan Neumann, Romeo A1 - Hesse, Rene A1 - Meyer, Christian A1 - Kranzmann, Axel T1 - Microstructure of alumina coating on steel P92 after thermal cycling N2 - 1. Introduction Alumina coatings are one possibility to increase the corrosion resistance, lifetime and application range of thermally loaded steel components, e.g. in modern power plants where the use of the Oxy-fuel technology corrosive fuel gas (H2O-CO2-O2-SO2 at 650 °C) affects the steel parts. In previous investigations the efficacy of protective alumina coatings on steel P 92 under those conditions was demonstrated. A shutdown and re-start of power plants or parts of them causes thermal stresses of the components which can cause detrimental effects like microstructural changes in the steel itself, changes in its oxidation behavior, delamination or microstructural changes in the coating. All those effects can lead to failure of the components, resulting in lifetime reduction. 2. Objectives As a first step, we concentrate on the influence of thermal cycling tests and observe the impact on the microstructure of the coating and the interface in laboratory air. These investigations will help understanding the processes which occur, show directions of potentially necessary changes of the coating due to improved thermal stress behaviour. 3. Materials & methods P 92 is a ferritic-martensitic steel, containing 9% Cr which forms protective Cr-oxide-rich scales in dry environments and non-protective ones in water-containing environments. Coupons of P 92, having ground surfaces, were dip-coated via a sol-gel process and subjected to thermal cycling for 500 h (1000 cycles) in laboratory air in a temperature range between room temperature and 660° C. The resulting mass loss was determined by weighing. Samples for TEM investigations were produced as cross sections normal to the sample surface by FIB preparation (Quanta 3D, (FEI)). The TEM/STEM investigations were performed using a JEM2200FS (JEOL) operated at 200 kV. The microstructure of the coating and the interface after cycling tests was characterized via TEM, HREM, and STEM images, electron diffraction as well as EDX and EFTEM methods. 4. Results At steep edges in the surface profile the coating was imperfect and cracks have formed during the thermal cycling. Flat surface regions are well-covered. The whole interface region between the steel and the coating shows a dense Cr-oxide-rich zone, which can form protective regions in case of local failure. The Cr-oxide zone is followed by a region of mixed oxides, containing Cr, Mn, Fe, and Al in variable composition, to which a porous δ-Al2O3 zone is joined. 5. Conclusions • Alumina coatings promote the formation of dense, Cr-rich zones at the interface, which makes the system self-healing. • These zones are stable during thermal stresses, even in regions with cracked coatings. • They cause reduction of outward diffusion and mass loss during thermal cycling. T2 - MC2017 CY - Lausanne, Switzerland DA - 21.08.2017 KW - Coating KW - Thermal cycling KW - TEM PY - 2017 UR - https://www.mc2017.ch/general-information/downloads/ AN - OPUS4-41724 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Röhsler, Andreas A1 - Sobol, Oded A1 - Nolze, Gert A1 - Unger, Wolfgang A1 - Böllinghaus, Thomas T1 - The use of time-of-flight secondary ion mass spectrometry for the investigation of hydrogen-induced effects in austenitic steel AISI 304L N2 - In the course of the energy transformation from fossil fuels to renewable energy sources, the use of hydrogen as fuel and energy storage can play a key role. This presents new challenges to industry and scientific community alike. The storage and transport of hydrogen, which is nowadays mainly realised by austenitic stainless steels, remains problematic. That is due to the degradation of mechanical properties and the possibility of phase transformation by hydrogen diffusion and accumulation. Development of materials and technologies requires a fundamental understanding of these degradation processes. Therefore, studying the behaviour of hydrogen in austenitic steel contributes to an understanding of the damage processes which is crucial for both life assessment and safe use of components in industry and transportation. As one of the few tools that is capable of depicting the distribution of hydrogen in steels, time-of-flight secondary ion mass spectrometry (ToF-SIMS) was conducted after electrochemical charging. To obtain furthermore information about the structural composition and cracking behaviour, electron-backscattered diffraction (EBSD) and scanning electron microscopy (SEM) were performed. Gathered data of chemical composition and topography was treated employing data fusion, thus creating a comprehensive portrait of hydrogen-induced effects in the austenite grade AISI 304L. Specimens were electrochemically charged with deuterium instead of hydrogen. This arises from the difficulties to distinguish between artificially charged hydrogen and traces existing in the material or the rest gas in the analysis chamber. Similar diffusion and permeation behaviour, as well as solubility, allow nonetheless to draw conclusions from the experiments. T2 - SIMS21 CY - Krakau, Poland DA - 11.09.2017 KW - Austenitic stainless steel KW - ToF-SIMS KW - Hydrogen PY - 2017 AN - OPUS4-42315 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Griepentrog, Michael A1 - Reinstädt, Philipp A1 - Wollschläger, Nicole A1 - Zeigmeister, U. T1 - Size effects in electrodeposited Ni-coatings N2 - Polycrystalline Ni materials with grain sizes less than 100 nm (nano crystalline NC) and with grain sizes in the micrometer range (micro crystalline MC) in form of thin films have become important in many technologies due to their improved physical, chemical and mechanical properties. Usual the mechanical properties of such coatings are described by a Hardness value and a Young´s modulus measured by Instrumented Indentation Testing (IIT).The behavior of such coatings during indentation test is influenced by different size effects having their representative length scale – grain size, coating thickness, length that characterizes the depth dependence of the hardness (Indentation Size Effect ISE). To estimate realistic values for the intrinsic coating Hardness and Young´s modulus all size effects have to be considered. For this work thin nano crystalline Ni – coatings (average grain size 30 nm) with thickness from 1 μm to 5 μm were electrodeposited on brass substrates. Indentation tests in the continuous stiffness measurement (CSM) mode were provided on as prepared Ni – coatings using a G200 Nanoindentation system (Fa. Keysight). For estimation of the intrinsic hardness of the coatings from composite hardness values calculated from the measured force –displacement curve using the Oliver & Pharr method, the model described by Z.S. Ma [1] was used. It was found that the experimental data can be well described by the model. The fitted values for the intrinsic hardness and the fitting parameters will be given. The different values of intrinsic hardness and of length characterizing depth dependence of the hardness for different coating thickness are discussed as results of changes in the coating structure because of changes in deposition parameters. [1] Z.S. Ma, Y.C. Zhou, S.G. Long, C. Lu: On the intrinsic hardness of a metallic film/substrate system: Indentation size and substrate effects. International Journal of Plasticity 34 (2012) 1-11. This work is supported by European Metrology Program for Innovation and Research (EMPIR) (JRP 14IND03 Strength – ABLE) T2 - Conference: Nanomechanical Testing in Materials Research and Development CY - Dubrovnik, Croatia DA - 01.10.2017 KW - Size effect KW - Substrate effect KW - Electrodeposited Ni - coatings KW - Instrumented indentation testing PY - 2017 AN - OPUS4-42664 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stajanca, Pavol A1 - Pötschke, Samuel A1 - Krebber, Katerina T1 - Post-fabrication cladding doping of commercial PMMA polymer optical fiber N2 - Possibility of post-fabrication doping of commercial PMMA fibers using well-known solution doping technique is presented. The cladding of 1 mm PMMA fiber is doped with Rhodamine B with the help of methanol-mediated diffusion of the dye molecules into the fiber material. Doping of the fiber core was not possible even at extended doping times. The proposed method represents rather simple and cheap way for preparing custom cladding-doped POFs with high flexibility of dopant choice and fiber length. Produced cladding-doped fibers have potential for various sensing or lighting applications. T2 - 26th International Conference on Plastic Optical Fibres (POF 2017) CY - Aveiro, Portugal DA - 13.09.2017 KW - Polymer optical fibers KW - Fluorescent dyes KW - Solution doping KW - Polymethyl methacrylate PY - 2017 AN - OPUS4-42321 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Barnefske, Lena A1 - Wachtendorf, Volker T1 - Self-healing silicone rubber for F-POF partial discharge sensors in HV cable accessories N2 - To avoid a catastrophic failure of insulation in high-voltage (HV) applications, a monitoring of partial discharges (PD) is necessary. Fluorescently labelled polymer optical fibres (F-POF) offer an electrically passive method for PD detection in HV facilities. F-POF could be embedded into HV cable insulation material, which are usually made of silicone rubber. Due to the difficult accessibility of HV cable accessories, a self-healing silicone rubber, based on incorporated capsules, with prolonged service life after PD detection represents an attractive material design for HV electrical insulation. T2 - 26th International Conference on Plastic Optical Fibres CY - Aveiro, Portugal DA - 13.09.2017 KW - Fluorescent polymer optical fibres KW - Partial discharge detection KW - High voltage cable accessories KW - Self-healing KW - Silicone rubber PY - 2017 AN - OPUS4-42511 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koerdt, Andrea T1 - The impact of methanogenic Archaea on material, environment and health N2 - Different environmental samples reveal that methanogenic Archaea are part of a multi-species biofilm on corroding metallic structures (Fig. 1). Studies on microbial influenced corrosion (MIC) focus mainly on sulphate reducing Bacteria (SRB), leading to the assumption that they are exclusively responsible for metal corrosion. In fact, methanogenic Archaea are known to be involved in metal corrosion as well (e.g.Methanococcus maripaludis DSM 2067). In some cases SRB and methanogenic Archaea have comparable high corrosion rates. However, the underlying mechanisms causing corrosion are still unknown. The goal of this study is to analyse two environmental isolates (M. maripaludis DSM 2067, M. maripaludis KA1) and two human-related isolates (Methanobrevibacter oralis and Methanobrevibacter smithii) for their ability to deteriorate/transform metals, which are relevant for technical and clinical applications. Moreover, the studies will provide essential information on the interaction mechanisms of human-related Archaea, which are frequently found in peri-implantitis, with dental material such as implants, crowns and bridges leading to their degradation/transformation. T2 - IBRG-Tagung CY - Berlin, Germany DA - 26.04.17 KW - Biofilm KW - Corrosion KW - Implants KW - Methanogens KW - Archaea KW - Anaerob PY - 2017 AN - OPUS4-42492 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Géraldine A1 - Harsha, A. P. A1 - Gradt, Thomas T1 - On the sliding behavior of PAEK composites in vacuum environment N2 - The tribological behavior of PAEK composites were investigated in air and vacuum environment. Results indicate that the tribological performance of these compounds depends on material compositions, fiber orientation as well as test conditions. In vacuum, very low friction and wear coefficient were obtained at low sliding speed while severe wear occurred at high speed. T2 - The 6th World Tribology Congress - WTC 2017 CY - Beijing, China DA - 17.09.2017 KW - PAEK KW - Sliding performances KW - Vacuum PY - 2017 AN - OPUS4-42447 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Monks, Melissa-Jane A1 - Ritter, B. A1 - Würth, Christian A1 - Krahl, T. A1 - Kemnitz, E. A1 - Resch-Genger, Ute T1 - Rare earth strontium fluoride nanocrystals prepared via sol gel synthesis - Spectroscopic study of upconversion luminescence properties N2 - Obtaining high quality upconverting nanocrystals with only little crystal defects and hence, a high luminescence, affords a reliable synthesis route. Only this guarantees the reproducibility of the material and its spectroscopic properties required for future application. The fluorolytic sol-gel synthesis appears to be a convenient attempt, as this is a method with only few steps influencing the material properties, which can be well controlled. Also creating bright upconverting nanocrystals requires a profound understanding of the interplay of photophysical processes like multiphoton absorption, radiative and non-radiative pathways, and energy transfer in the material. Based on steady-state and time resolved luminescence measurements at different excitation power densities, the influence of the lanthanide doping ratio and synthesis parameters such as the annealing process on SrF2-nanocrystals obtained via the fluorolytic sol-gel synthesis was systematically studied. T2 - GDCh Wissenschaftsforum Chemie CY - Berlin, Germany DA - 10.09.2017 KW - Upconversion KW - Strontiumfluoride KW - Annealing study KW - Doping study KW - Luminescence PY - 2017 AN - OPUS4-42944 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Agea Blanco, Boris A1 - Reinsch, Stefan A1 - Meyer, Christian A1 - Müller, Ralf A1 - Günster, Jens T1 - Quantification of sand erosion on PV solar glass N2 - Solar glass in arid and semi-arid regions is exposed to sand storms which can affect the durability of PV modules. Related erosion processes have been extensively studied but the results given are difficult to compare due to being obtained by different variables like particle speed and sand mass. This study correlates the damage of solar panels to the cumulative impact energy as a global parameter. T2 - 91. Glastechnische Tagung CY - Weimar, Germany DA - 29.05.2017 KW - Glass KW - Sandblasting KW - Erosion KW - Sandstorm KW - Transmittance KW - Roughness PY - 2017 AN - OPUS4-42856 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Breitfeld, Steffen A1 - Scholz, Gudrun A1 - Emmerling, Franziska A1 - Kemnitz, Erhard T1 - High energy ball milling of a new representative of coordination polymers without organofluorine linkers N2 - Metal organic frameworks and coordination polymers play an important role in different fields of applications. Moreover, particularly fluorinated metal-organic frameworks (FMOFs) are in the focus of interest during the last years. In most cases, fluorine is implemented using perfluorinated organic linkers at the synthesis, usually performed by solvothermal synthesis. However, only few examples are known so far where fluorine is coordinated directly to the metal cation. Recently, we reported about mechanochemical syntheses and characterization of fluorine-containing coordination polymers of alkaline earth metals by milling M(OH) (M: Ca, Sr, Ba) with fluorinated benzene dicarboxylic acids 2 and we reported about mechanochemical syntheses of alkaline earth metal fluorides with ammonium fluoride. Now we are reporting about a combination of both synthesis routes. That is the first mechanochemical synthesis of coordination polymers where fluorine is coordinated directly to the metal cation. T2 - Konferenz CY - Berlin, Germany DA - 30.11.2017 KW - Metal organic frameworks KW - Coordination polymer KW - Mechanochemical syntheses KW - Direct fluorine-metal bond KW - Alkaline earth metal PY - 2017 AN - OPUS4-46898 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Blaeß, Carsten A1 - Müller, Ralf A1 - Thompson, Cyrus T1 - Crack healing in glasses N2 - Fundamental understanding of crack healing in glassy crystalline materials is very important for many applications, especially for solid oxide fuel cells (SOFC) sealants since cracks caused by mechanical stress or thermal cycling still remain a substantial bottleneck in developing durable SOFC. Previous studies on soda lime silicate glass published by Singh showed that crack healing is driven by viscous flow. There he postulated that the healing progress is proportional to time, t, and the inverse viscosity. This finding would allow to present for a given glass data of crack healing measured at different temperatures in a master curve, if the healing progress is plotted versus t/η. Such master curves would be a helpful tool in understanding crack healing kinetics. To verify the applicability of such master curves, crack healing in non-crystallizing soda-lime-silicate (NCS) and sodium-borosilicate glasses (NBS) was studied. Cracks were generated by Vickers indention and healed isothermally at different temperatures. Crack healing progress was monitored by optical and electron microscopy. The results show that the above mentioned proportionalities applies to the two glasses. In both cases the afore developed master curve could be obtained. T2 - 91. Jahrestagung HVG-DGG CY - Weimar, Germany DA - 29.05.2017 KW - Glass KW - Crack healing PY - 2017 AN - OPUS4-41347 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Blaeß, Carsten A1 - Müller, Ralf A1 - Thompson, Cyrus T1 - Crack healing in glass matrix composites N2 - Partially crystalline glasses are predominantly used as solid oxide fuel cell (SOFC) sealants due to their superior long term durability. However, cracks caused by thermal cycling still remain a substantial bottleneck in developing durable SOFC sealants inasmuch as, in contrast to crystal free glasses, large crystal volume fractions can retard healing. Hence, the basic understanding of crack healing in glassy crystalline materials and the effects of micro structure are important for finding optimum micro structures for both, durability and crack healing. For studying these effects, several model glass matrix composites (GMC), for which simultaneous crystal growth and crack healing can be excluded, have been synthesized. Sodium calcium silicate glass – zirconia GMC turned out to provide sufficiently homogeneous, dense and durable model GMC for our studies. The microstructure of this GMC shows large crystal free glassy regions embedded in network of finely dispersed ZrO2 nanoscale crystals. Whereas the glassy regions allow easy local crack healing, the network of dispersed crystals increases the effective viscosity on a global scale. This effect substantially retards crack broadening during later healing stages, which often ends up in large pores. Therefore, this type of microstructure seems to be an interesting candidate for crack healing optimized sealants. T2 - 91. Jahrestagung HVG-DGG CY - Weimar, Germany DA - 29.05.2017 KW - Glass KW - Crack healing KW - Glass ceramic KW - Composite PY - 2017 AN - OPUS4-41348 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feldmann, Titus A1 - Fedelich, Bernard A1 - Epishin, Alexander A1 - Charmi, Amir T1 - Simulation of creep of a single crystal superalloy considering the transport of dislocations N2 - The investigation of creep behavior of the single crystal superalloy CMSX-4 at 1288°C is important for the understanding of deformations mechanisms under hot isostatic pressing (HIP). This treatment is used to increase the lifetime of single crystal superalloys by reducing the number of cavities. The understanding of the internal processes during this treatment is still limited due to the material being not single-phase at room temperature, the extreme conditions of HIP and the complexity of the material. The result of predicting the pore shrinkage rate using classical crystal plasticity was not satisfying. A more complex model has been implemented, now taking the heterogeneity of dislocation sources into account. By introducing a dislocation density, one can describe the transport, nucleation and interaction of dislocations. T2 - ICMM5 CY - Rome, Italy DA - 14.6.2017 KW - Einkristalllegierung KW - Kristallplastizität PY - 2017 AN - OPUS4-42036 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nguyen, Thi Yen A1 - Bernardes, C. E. S. A1 - Minas da Piedade, M. E. A1 - Rademann, K. A1 - Emmerling, Franziska T1 - Guided crystallization: The influence of solvent and concentration N2 - Theoretical and experimental studies indicate that crystal nucleation can take more complex pathways than expected on the ground of the classical nucleation theory. A direct in situ observation of the different pathways of nucleation from solution is challenging since the paths can be influenced by heterogeneous nucleation sites, such as container walls. The custom-made acoustic levitator using in these experiments regulates the influence that solid surfaces, temperature, and humidity have on the crystallization process. The investigations of the crystallization process of paracetamol were performed with in situ analytical techniques and theoretical simulations to gain a comprehensive insight into processes, occurring intermediates, and required reaction conditions. The targeted choice of the solvent and the concentration enabled the guidance of the pathways, therefore, resulting in the isolation of one desired crystalline structure. T2 - Annual COST meeting CY - Lincoln, United Kingdom DA - 25.06.2017 KW - Crystallization KW - Polymorphism KW - Molecular dynamic simulation KW - Pair distribution function analysis KW - XRD PY - 2017 AN - OPUS4-41111 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Castro, R. A. E. A1 - Cortesao, A. M. A1 - Maria, T. M. R. A1 - Silva, M. R. A1 - Emmerling, Franziska A1 - Canotilho, J. A1 - Eusebio, M. E. S. T1 - New cocrystals of bexarotene with pyridinecarboxamide isomers sustained by the acid∙∙∙aromatic nitrogen supramolecular heterosynthon N2 - Pharmaceutical cocrystals are homogenous crystalline structures made up of two or more components in a definite stoichiometric ratio, where at least one of the components in the crystal lattice is an active pharmaceutical ingredient (API).1 Pharmaceutical cocrystals have opened the opportunity for engineering solid-state forms designed to have tailored properties to enhance drug product bioavailability and stability, as well a enhance processability of the solid material inputs in drug product manufacture. In this work the cocrystallization of bexarotene, an approved API by the U.S. Food and Drug Administration that belongs to Biopharmaceutics Classification System Class II (low solubility–high permeability), with pyridine carboxamide isomers (picolinamide, nicotinamide and isonicotinamide) was successfully undertaken. The synthesis was achieved by liquid assisted grinding (LAG) and the solids obtained were characterized by differential scanning calorimetry (DSC), infrared spectroscopy (FTIR-ATR), powder X-ray diffraction (XRPD), single crystal X-ray diffraction (SXD), and polarized light thermomicroscopy (PLTM). For bexarotene: picolinamide and bexarotene:isonicotinamide, 1:1 cocrystals were obtained directly from milling. SXD data of bexarotene:isonicotinamide cocrystal reveal acid∙∙∙aromatic nitrogen supramolecular heterosynthon and that the homosynthon amide∙∙∙amide in isonicotinamide is preserved. The bexarotene:nicotinamide mixtures prepared by ball milling give rise to simple binary solid–liquid phase diagram with an eutectic point, well described by the Schröder-van Laar equation. Melt crystallization of the 1:1 mixture gives rise to a cocrystal for which a complex phase behaviour is observed. T2 - 6th Meeting IAPC CY - Zagreb, Croatia DA - 04.09.2017 KW - Crystalline structure KW - Bexarotene KW - Powder X-ray diffraction KW - Single crystal X-ray diffraction KW - Infrared spectroscopy PY - 2017 AN - OPUS4-41063 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rosignuolo, F. A1 - Chaves Spoglianti de Souza, Roberto A1 - Andreini, M. A1 - La Mendola, S. A1 - Knaust, Christian T1 - A comparison between empirical models and FDS simulation to predict the ceiling gas temperature distribution in a tunnel fire N2 - A comparison between the results obtained from a Computational Fluid Dynamic (CFD) simulation and from the application of an empirical formula for determining the temperature distribution inside a tunnel in case of fire is presented. The temperature is measured and calculated at different distances from the location of the fire and at different time intervals. The fire considered varies with time following a time-heat release rate curve which has a parabolic growing phase, a constant period and a linear decay. The comparison reveals differences in the results. The temperatures calculated with the empirical formula resulted higher than the temperatures obtained by means of the CFD simulation. A list of possible reasons for this limited correspondence is also presented and commented. A proposal for further studies to better define the limitations of both the procedures and to define the influence of each parameter involved is finally presented. T2 - World Tunnel Congress 2017 – Surface challenges – Underground solutions CY - Bergen, Norway DA - 09.06.2017 KW - CFD KW - Fire KW - Tunnel KW - Design Fire PY - 2017 AN - OPUS4-40655 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Waurischk, Tina A1 - Balzer, R. A1 - Kiefer, P. A1 - Reinsch, Stefan A1 - Müller, Ralf A1 - Behrens, H. A1 - Deubener, J. T1 - New device for inert crack growth measurements in ultra-strong glasses N2 - The practical strength of glasses under ambient conditions is substantially lower compared to its intrinsic strength because of sub-critical crack growth (SCCG) from microscopic flaws. While SCCG is related to the humidity of the ambient atmosphere, leading to stress corrosion phenomena, the detailed kinetics are still not fully understood. To get better insight to the contribution of water on the crack-tip, highly water bearing glasses will be investigated by a new device for inert SCCG-measurements using double cantilever beam (DCB) geometry specimens. This device was designed to investigate the stress intensity factor in modus I and crack velocity in vacuum, but different atmospheres can also be introduced. For validation of the new device, first experiments were performed on microscope slides as well as on a soda-lime silicate and a borosilicate crown glass. The results achieved will be presented in comparison to the published results of Wiederhorn. T2 - 91. Glastechnische Tagung CY - Weimar, Germany DA - 29.05.2017 KW - Double cantilever beam KW - DCB KW - Crack intensity factor KW - Crack growth velocity KW - Glass PY - 2017 AN - OPUS4-40680 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Frenzel, Florian A1 - Würth, Christian A1 - Muhr, V. A1 - Hirsch, T. A1 - Resch-Genger, Ute T1 - Power dependent optical properties of hexagonal β-NaYF4: x % Er3+, 20 % Yb3+ core/ core-shell upconversion nanoparticles in cyclohexane and water N2 - Lanthanide doped photon upconverting nanophosphors (UCNPs) have the unique capability to produce narrow band, multi-color emission in the UV/vis/NIR upon multiphotonic absorption of infrared light, which makes them promising reporters for diagnostic, bioanalytical, and biological applications. This minimizes background signals, which normally occur due to autofluorescence from auxochromes, in biological matrices and enables deep penetration depths in biological applications. Moreover, UCNPs show long luminescence lifetimes in the μs range favorable for time gated emission in conjunction with a high photostability and chemical inertness and they do not blink. One of the most efficient upconversion (UC) phosphors for conversion of 976 nm to 655 nm and 545 nm light presents the hexagonal NaYF4-host crystal doped with 20 % Yb3+ used as sensitizer to absorb infrared light and 2 % Er3+ acting as activator mainly responsible for light emission. The high transparency in the relevant spectral windows of this host together with its low phonon frequencies ensure relatively high luminescence efficiencies. Although UCNPs are ideal candidates for many chemical and biological sensing and imaging applications, compared to other well-known chromophores like organic dyes or QDs, they suffer from a comparatively low brightness due to the low absorption cross sections of the parity forbidden f-f-transitions and low photoluminescence quantum yields (QYUC) particularly in the case of small nanoparticles with sizes of < 50 nm. The rational design of more efficient UCNPs requires an improved understanding of the nonradiative decay pathways in these materials that are influenced by particle architecture including dopant ion concentration and homogeneity of dopant distribution within UCNPs, size/surface-to-volume ratio, surface chemistry, and microenvironment. A promising approach to overcome the low efficiency of UCNPs is to use plasmonic interactions between a noble metal (Ag or Au) structure in the proximity of UCNPs and the incident light. This interaction leads to a modification of the spectroscopic properties due to local field enhancements and can involve an increase of the photoluminescence. In this respect, we study the interactions of UCNPs with metal structures (clusters and shells) by varying shape and size. Here, first results derived from integrating sphere spectroscopy and time-resolved fluorescence measurements are presented. T2 - Summer School "EXCITING NANOSTRUCTURES" CY - Bad Honnef, Germany DA - 17.07.2017 KW - Upconversion KW - Nanoparticle KW - Flourescence KW - Core-shell architecture KW - NIR KW - Absolute flourometry KW - Integrating sphere spectroscopy KW - Er(III) KW - Yb(III) KW - Single particle spectroscopy PY - 2017 AN - OPUS4-41172 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -