TY - THES A1 - Schlichting, Joachim T1 - Integrale Verfahren der aktiven Infrarotthermografie N2 - Die zerstörungsfreie Prüfung ist eine Aufgabe von großer Bedeutung, sowohl aus wirtschaftlicher Perspektive, als auch um die notwendige Sicherheit technischer Systeme gewährleisten zu können. Mit der Thermografie steht eine schnelle und berührungslose Prüftechnik zur Verfügung, die nicht zuletzt wegen der rapiden Entwicklung auf dem Gebiet der Infrarotkameras in letzter Zeit große Aufmerksamkeit erfährt. Typischerweise werden thermografisch oberflächennahe, parallel zur Oberfläche ausgedehnte Defekte nachgewiesen. In dieser Arbeit werden zwei untypische Prüfprobleme gelöst. An Punktschweißverbindungen wird mit der Linsengröße eine Struktur in der Mitte der Probe mittels Blitzlichtthermografie indirekt vermessen. Hier können typische Fehlerbilder wie Klebverbindungen und Spritzer sicher erkannt werden, was statistisch abgesichert durch eine Serienmessung und den Vergleich mit zerstörender Prüfung gezeigt wird. Ein Beispiel für orthogonal zur Oberfläche orientierte Fehlstellen stellen Risse dar, wie sie beispielsweise in Schweißnähtenn häufig auftreten. Neben der Entwicklung eines Verfahrens zur Detektion von Rissen, welches auf kommerziell erhältlichen Geräten aufbaut, wurde in Experimenten und Finite-Elemente-Simulationen untersucht, inwieweit sich auch die geometrischen Eigenschaften bestimmen lassen. Mit einem Verfahren, das ebenso wie die Methode zur Prüfung der Schweißpunkte auf der Analyse zeitlich und räumlich integraler Größen basiert, die vom thermischen Widerstand abhängen, ist die gleichzeitige Bestimmung von Winkel und Tiefe möglich. N2 - Non-destructive evaluation is a task of utmost importance for both, the economic point of view and to guarantee the required safety and reliability of technical systems. Thermography is a fast and contactless technique which received continued attention not least through the significant price drop at the infrared camera market. It is typically used to detect near-surface defects which are expanded parallel to the surface. This thesis deals with two non-standard inspection tasks. With the weld lens diameter of spot welds, a feature in the sample's geometrical center is indirectly sized by ash thermography. The presented method is suitable to distinguish typical error classes like stick welds or expulsions. This fact is validated by statistical evaluations of thermographic and destructive test series. As an example for perpendicularly oriented imperfections, surface cracks are investigated, which can be a major problem at welding seams. A technique for detecting cracks entirely based on commercially available equipment is developed. In addition, the accessibility of geometric characteristics of cracks was examined by experiments and FEM-simulations. Similar to the method developed for assessing spot welds, an approach based on the analysis of spatial and temporal integral quantities which depend on the thermal resistance is used. In doing so, the simultaneous determination of crack angle and depth is possible. T3 - BAM Dissertationsreihe - 91 KW - Aktive Thermografie KW - FEM KW - Spot Welding KW - Cracks KW - Nondesstructive Evaluation KW - Active Thermography KW - Zerstörungsfreie Prüfung KW - Punktschweißen KW - Risse KW - FEM PY - 2012 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-676 SN - 978-3-9815134-6-2 SN - 1613-4249 VL - 91 SP - 1 EP - 209 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-67 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Schilling, Markus T1 - Environmental Stress Cracking (ESC) and Slow Crack Growth (SCG) of PE-HD induced by external fluids N2 - High-density polyethylene (PE-HD) is widely used as a packaging material. Typical applications are pipes and containers for storage and transport of dangerous goods. For these applications, the understanding of the craze-crack damage mechanisms slow crack growth (SCG) and environmental stress cracking (ESC) is of importance. Since these mechanisms are considered to be the major causes of failure, their understanding is essential for inspection and release of those materials. A well-established test method for the assessment of these damage mechanisms is the full-notch creep test (FNCT). It is used in this study for a detailed investigation of crack propagation phenomena in PE-HD container materials under the influence of different fluids such as air, water and aqueous detergent solutions (Arkopal N 100) as well as biodiesel and diesel. Based on the results of the FNCT, a classification scheme of different fluids is proposed, which allows for an assignment of the respective damage mechanisms. Hereby, it is differentiated between (i) inert, (ii) purely surface-active and (iii) additionally sorptive, bulk-active fluids with respect to SCG. If the test fluid changes the intrinsic properties (at the surface or in the bulk), the damage mechanism is addressed to ESC behavior. In FNCT investigations, stress, temperature and specimen geometry were varied systematically. In addition to the time to failure as common measure for the resistance of a PE-HD type against crack propagation, specimen elongation was considered in detail. Several imaging techniques were applied for fracture surface analysis of specimens tested in FNCT to gain novel information on SCG and ESC behavior. From height profiles obtained by laser scanning microscopy (LSM) and information on surface structures from scanning electron microscopy (SEM), indicators for the differentiation of the crack propagation mechanisms could be derived. Based on the LSM data, an algorithm for the distinction between ductile shear deformation and brittle crack growth as dominating failure mechanism was developed. Imaging techniques were also used for determination of crack propagation rates, which were related to time-resolved FNCT elongation data. From the time-resolved determination of crack lengths of partly damaged FNCT specimens, an increasing length of craze zone with a progressively propagating crack was revealed for the first time. This relation of crack and craze zones was specified by fracture mechanical considerations. N2 - Polyethylen hoher Dichte (PE-HD) wird als Werkstoff für Rohre und Behälter für den Transport und zur Lagerung von Gefahrgütern verwendet. Für die Beurteilung und technische Freigabe dieser Materialien ist das Verständnis der beiden Schädigungsmechanismen „langsames Risswachstum“ (engl.: „slow crack growth“, SCG) und „umgebungsbedingter Spannungsriss“ (engl.: „environmental stress cracking“, ESC) essentiell. Eine etablierte Prüfmethode zur Bewertung dieser Schädigungsmechanismen ist der Full-Notch Creep Test (FNCT), der in dieser Arbeit zur systematischen Untersuchung des Risswachstums in PE-HD Behältermaterialien unter Einwirkung von Luft, Wasser und wässrigen Netzmittellösungen (Arkopal N 100) sowie Biodiesel und Diesel verwendet wird. Aus den Ergebnissen des FNCT wird ein Klassifikationsschema für Fluide vorgeschlagen, welches ebenfalls eine Zuordnung zu den Schädigungsmechanismen erlaubt. Hierbei wird in (i) inerte, (ii) rein oberflächen-aktive und (iii) zusätzliche sorptive, volumen-aktive Fluide hinsichtlich des langsamen Risswachstums (SCG) unterschieden. Wenn ein Fluid lokal die intrinsischen Materialeigenschaften des Polymers verändert, wird der Schädigungsmechanismus dem umgebungsbedingten Spannungsriss (ESC) zugeordnet. Bei den FNCT-Untersuchungen wurden die mechanische Spannung, die Temperatur und die Prüfkörpergeometrie systematisch variiert. Zusätzlich zur Standzeit wurde die Prüfkörperdehnung zeitabhängig erfasst. Aus einer erweiterten Bruchflächenanalyse konnten neuartige Informationen über SCG und ESC erhalten werden. Hierzu wurden verschiedene Bildgebungsverfahren verwendet. Insbesondere wurden mit Laserscanningmikroskopie (LSM) Höhenprofile und mit Rasterelektronenmikroskopie (REM) Oberflächeninformationen zur Charakterisierung der Rissfortschrittsmechanismen erhalten. Auf Basis der LSM wurde unter Zuhilfenahme von Höhenprofildaten ein Algorithmus zur Unterscheidung zwischen duktiler Scherverformung und sprödem Risswachstum als dominierende Schädigungsmechanismen entwickelt. Die aus den bildgebenden Verfahren ermittelten Rissfortschrittsraten konnten mit den Daten der während des FNCT erfassten Dehnung der Prüfkörper in Beziehung gesetzt werden. Weiterhin wurde mithilfe von zeitaufgelösten Risslängendaten erstmals eine direkte Korrelation der Risslänge zu vorgeschädigten, fibrillierten Bereichen (Crazes) im PE-HD Prüfkörper während des FNCT nachgewiesen. Demnach vergrößert sich die Craze-Länge linear mit zunehmender Risslänge. Dieser Zusammenhang zwischen Riss- und Craze-Längen wurde auf mathematisch, bruchmechanischer Grundlage bestätigt. KW - High-density polyethylene (PE-HD) KW - Full-Notch Creep Test (FNCT) KW - Slow crack growth (SCG) KW - Environmental Stress Cracking (ESC) KW - Biodiesel KW - Diesel KW - Crack propagation analysis KW - Fracture Surface Analysis KW - Test Improvement KW - Imaging PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:tuda-tuprints-115443 DO - https://doi.org/10.25534/tuprints-00011544 SP - 1 EP - 212 CY - Darmstadt AN - OPUS4-50941 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Schempp, Philipp T1 - Grain refinement in aluminium GTA welds N2 - Grain refinement is an important opportunity to improve mechanical properties of fusion welds and the weldability (cracking sensitivity) of the base metal. In this thesis, grain refinement was achieved for aluminium welds by additions of a grain refiner. For this purpose, inserts consisting of aluminium base metal and small additions of commercial Al Ti5B1 grain refiner were cast, deposited in base metal plates, and fused in a gas tungsten arc (GTA) welding process. As a result, higher grain refiner additions increased the weld’s titanium and boron content resulting in a significant decrease in the weld metal mean grain size up to 86%. This grain size reduction led to a transition from predominantly columnar to equiaxed grain shape (columnar to equiaxed transition CET). The grain refinement was thereby found to be strongly dependent upon the base metal chemical composition. Accordingly, the grain refining efficiency was the highest in commercial pure Al (Alloy 1050A, Al 99.5), followed by Alloy 6082 (Al Si1MgMn) and Alloy 5083 (Al Mg4.5Mn0.7). In this regard, the parameters P and Q were applied to investigate the influence of alloying elements on the supply of constitutional undercooling during solidification and on final grain size. Also, WDS (wavelength dispersive x-ray spectroscopy) and TEM (transmission electron microscopy) analysis found an increasing number of particles rich in Ti and B. These substrates are probably TiB2 particles coated by Al3Ti likely nucleating Al grains during solidification. The variation in torch speed showed that increasing torch speeds support the CET effect leading to many small and equiaxed grains at high torch speed. To give explanations for this observation, the thermal conditions, that are controlled by welding parameters such as torch speed, were determined with temperature measurements via thermocouples. These measurements revealed that solidification parameters like solidification growth rate, cooling rate, (local) thermal gradient and solidification time vary significantly along the solidification front (from weld centreline to weld fusion line). In a further step, the solidification parameters were related to the corresponding grain size and shape. On the basis of this comparison, an analytical approach was used to model the CET. This allowed the prediction of critical values for both solidification growth rate and thermal gradient, at which the CET occurs in aluminium weld metal. The influence of grain refinement on the weld mechanical properties was investigated in tensile tests. Accordingly, the ductility of Alloy 5083 welds was increased through grain refinement whereas no improvement in weld metal strength was observed. Furthermore, tear tests with notched specimens revealed for Alloy 1050A that the resistance against initiation and propagation of cracks in the weld metal can be enhanced through grain refinement. In addition, when welding Alloy 6082, weld metal grain refinement prevented the formation of centreline solidification cracking that was present only in welds with unrefined grain structure. On the basis of the above experiments, the Ti/B contents needed in commercial filler wires or rods to allow optimum weld metal grain refinement were estimated. Accordingly, this work gives specific recommendations to filler material producers through a simple calculation that considers the influence of base alloy and welding process. The results show that the Ti/B contents defined by the corresponding standards for filler alloys are too low to allow weld metal grain refinement. T3 - BAM Dissertationsreihe - 111 KW - Aluminium KW - Kornfeinung KW - WIG-Schweißen PY - 2013 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-477 SN - 978-3-9815944-4-7 SN - 1613-4249 VL - 111 SP - 1 EP - 121 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-47 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Samadurau, Uladzimir T1 - Entwicklung nichtlinearer tomographischer Rekonstruktionsverfahren für die Materialprüfung und Prozessüberwachung N2 - Die Studie beschäftigt sich mit der Entwicklung von Methoden und Algorithmen zur Rekonstruktion dynamischer Prozesse. Dabei werden neue Ansätze zur Lösung der Rekonstruktionsaufgabe vorgestellt. T3 - BAM Dissertationsreihe - 8 KW - Entwicklung nichtlinearer tomographischer Rekonstruktionsverfahren KW - Prozessüberwachung PY - 2005 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1500 SN - 978-3-86509-301-9 SN - 1613-4249 VL - 8 SP - 1 EP - 92 PB - Wirtschaftsverlag NW CY - Bremerhaven AN - OPUS4-150 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Rosemann, Paul T1 - Einfluss der Wärmebehandlung auf die Korrosionsbeständigkeit martensitischer nichtrostender Stähle N2 - Die Korrosionsbeständigkeit martensitischer nichtrostender Stähle (MNS) wird wesentlich durch die Legierungszusammensetzung und die Wärmebehandlung (WB) bestimmt. Verschiedene wissenschaftliche Arbeiten haben bereits gezeigt, dass der Anteil an Chromkarbiden im Gefüge von MNS sehr stark durch die WB (Austenitisierungstemperatur, Abkühlgeschwindigkeit und Anlasstemperatur) beeinflusst wird. Jedoch wurde der Zusammenhang zwischen den einzelnen Teilschritten sowie Parametern der WB und der Korrosionsbeständigkeit von MNS bisher nur unzureichend hergestellt. Die Literatur liefert außerdem gegensätzliche Aussagen über den Einfluss der Abkühlgeschwindigkeit auf die Korrosionsbeständigkeit von MNS. Daher werden im Rahmen dieser Arbeit systematische Grundlagenuntersuchungen an vier technisch relevanten MNS (X20Cr13, X46Cr13, X50CrMoV15 und X30CrMoN15-1) durchgeführt, um den Einfluss der WB auf die Korrosionsbeständigkeit aufzuklären. Es werden umfangreiche experimentelle Ergebnisse hinsichtlich Gefüge, Härte und Korrosionsbeständigkeit (EPR, KorroPad, kritische Lochkorrosionspotentiale) vorgestellt und mit thermodynamischen Berechnungen (ThermoCalc) korreliert. Aus den Ergebnissen wird außerdem abgeleitet, wie Kohlenstoff- und Stickstoffgehalt die Korrosionsbeständigkeit in Relation zur WB beeinflussen. Damit wird der Einfluss aller Wärmebehandlungsschritte und -parameter erstmals eindeutig und unabhängig voneinander für MNS beschrieben. Weiterführend wird erläutert, mit welchem Legierungskonzept und mit welcher WB MNS mit optimaler Korrosionsbeständigkeit hergestellt werden können und wie dies experimentell an technischen Produkten nachweisbar ist. KW - Wärmebehandlung KW - Korrosion KW - Nichtrostender Stahl KW - Lochkorrosion KW - EPR KW - KorroPad KW - Chromverarmung PY - 2017 SN - 978-3-8440-5404-0 DO - https://doi.org/10.2370/9783844054040 SP - 1 EP - 172 PB - Shaker Verlag CY - Aachen AN - OPUS4-41144 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Reusch, Frederik T1 - Entwicklung und Anwendung eines nicht-lokalen Materialmodells zur Simulation duktiler Schädigung in metallischen Werkstoffen N2 - Diese Arbeit umfasst die Entwicklung, Implementierung und Anwendung einer nicht-lokalen, gradientenabhängigen Erweiterung des lokalen Gurson-Modells zur Simulation duktiler Schädigung für metallische Werkstoffe, um die Anwendungsgrenzen lokaler Schädigungsmodelle im Rahmen der FE-Methode bzgl. Netzabhängigkeit und Lokalisierung von Simulationsergebnissen zu überwinden. Zu den offenen Problemen bei der Anwendung von lokalen, inelastischen Schädigungsmodellen gehört u. a. die Abhängigkeit der erzielten Ergebnisse von der Größe und Orientierung der zur Strukturdiskretisierung eingesetzten Finiten Elemente. Diese Netzabhängigkeit tritt insbesondere bei der Verwendung lokaler Stoffgesetze und der Simulation entfestigenden Materialverhaltens auf. Diese Beschränkungen lokaler Modelle sind maßgeblich auf den Eindeutigkeitsverlust der Lösung des Systems der konstitutiven Gleichungen durch die Modellierung von Entfestigungsvorgängen zurückzuführen. Ausgangspunkt für die Entwicklung einer nicht-lokalen Formulierung des Gurson- Modells stellt die Zielsetzung dar, die lokale Beschreibung der Schädigungsentwicklung durch die Evolutionsgleichung des Hohlraumvolumenanteils unter Berücksichtigung des Gradienten der räumlichen Schädigungsverteilung zu erweitern. T3 - BAM Dissertationsreihe - 1 KW - Schadensmechanik KW - Numerisches Modell KW - Duktilität KW - Rissausbreitung PY - 2003 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1573 SN - 978-3-86509-092-3 SN - 1613-4249 VL - 1 SP - 1 EP - 194 PB - Wirtschaftsverlag NW CY - Bremerhaven AN - OPUS4-157 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Reichelt, Manuel T1 - Untersuchungen zu ungeschmiertem Schwingungsverschleiß an 100Cr6-Kugeln gegen 100Cr6-Ebenen N2 - Die vorliegende Doktorarbeit handelt von der Bestimmung und der Untersuchung vom Verschleißvolumen und vom Verschleißkoeffizienten bei ungeschmierten Modellversuchen an 100Cr6-Ebenen und -Kugeln unter Schwingungsbeanspruchung. Die experimentelle Arbeit wurde mittels statistischer Auswertung einer großen Menge von eigenen und früheren Versuchsdaten an fünf Tribometern bei umfangreicher Variation der Beanspruchungsparameter durchgeführt. Ziel war es, die Wiederholbarkeit und Reproduzierbarkeit der experimentellen Ergebnisse zu überprüfen sowie das Archard-Gesetz zu verifizieren. Des Weiteren wurde der Einfluss der Luftfeuchtigkeit auf den Verschleiß untersucht. KW - Verschleißkoeffizient KW - 100Cr6-Stahl KW - Gesetz von Archard KW - Verschleiß-Map KW - relative Luftfeuchtigkeit PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-522664 DO - https://doi.org/10.14279/depositonce-10423 SP - 1 EP - 118 PB - Technische Universität Berlin CY - Berlin AN - OPUS4-52266 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Prewitz, Marc T1 - Charakterisierung von Glas-Polymer Verbundmaterialien fur die Hochdruckspeicherung von Wasserstoff N2 - In der vorliegenden Arbeit werden Glaskapillaren und Strukturen aus Borosilikatglas (Simax) f¨ur die Hochdruckspeicherung von Wasserstoff betrachtet. Um die mechanischen Belastungen zu analysieren und anschließend ein optimiertes Speicherdesign abzuleiten, findet die Finite Element Methode (FEM) Einsatz. Die notwendigen Materialkennwerte werden zuvor experimentell ermittelt. Dazu geh¨oren die Festigkeit, die Schubfestigkeit der Grenzfl¨ache Klebung/Glas, der Wasserstoffpermeationskoeffizient, das Temperatur-Zeit-abh¨angige Verhalten, sowie die obere Temperatureinsatzgrenze. Die Glasfestigkeit ist stark abh¨angig von der Oberfl¨acheng¨ute. Daher werden in dieser Arbeit Kapillaren selber gezogen und beschichtet. Der Einfluss auf die Festigkeit wird mit Hilfe von Berstversuchen untersucht. Die eingesetzten Polymere werden zus¨atzlich mit dem Push-out Versuch, der dynamisch mechanischen Analyse und der Permeationsmessung charakterisiert. Dar¨uber hinaus wird aus den DMA Versuchen ein viskoelastisches Materialmodell abgeleitet, womit der Temperatur- und Zeiteinfluss auf die mechanische Belastung simuliert wird. Unter Beachtung der experimentell gewonnenen Erkenntnisse, sowie der durchgef¨uhrten Simulation ist es m¨oglich, ein optimiertes Speicherdesign zu erstellen und Aussagen ¨uber die Einsatzgrenzen zu treffen. KW - Wasserstoffspeicherung KW - Glaskapillaren KW - Polymercoating PY - 2017 UR - https://depositonce.tu-berlin.de/handle/11303/6261 SP - 1 EP - 150 CY - Berlin AN - OPUS4-51065 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Perret, William T1 - Welding Simulation of Complex Automotive Welded Assembly - Possibilities and Limits of the Application of Analytical Temperature Field Solutions N2 - Before the development of computational science, heat conduction problems were mainly solved by analytical techniques. Analytical solutions are exact solutions of differential equations; the investigated physical phenomena, for instance the temperature, are solved locally for one single point independently of the rest of the investigated structure resulting in extremely short computational times. These analytical solutions are however only valid for some simple geometries and boundary conditions making their applications for complex industrial geometries directly not possible. Numerical techniques, such as the Finite Element Method, enable overcoming this problem. However, the numerical simulation of the structural heat effect of welding for complex and large assemblies requires high computational effort and time. Therefore, the wide application of welding simulation in industry is not established, yet. The aim of this study is to combine the advantages of analytical and numerical simulation methods to accelerate the calibration of the thermal model of structure welding simulation. This is done firstly by calibrating automatically the simulation model with a fast analytical temperature field solution and secondly by solving the welding simulation problem numerically with the analytically calibrated input parameters. In order to achieve this goal, the analytical solution of the heat conduction problem for a point source moving in an infinite solid was extended and validated against reference models until a solution for a volumetric heat source moving on a thin small sheet with several arbitrary curved welding paths was found. The potential of this analytical solution by means of computational time was subsequently demonstrated on a semi-industrial geometry with large dimensions and several curved welds. The combined method was then transferred to an industrial assembly welded with four parallel welds. For this joint geometry, it was possible to apply the extended analytical solution. The calibration of the simulation model was done automatically against experimental data by combining the extended fast analytical solution with a global optimisation algorithm. For this calibration, more than 3000 direct simulations were required which run in less computational time than one corresponding single numerical simulation. The results of the numerical simulation executed with the analytically calibrated input parameters matched the experimental data within a scatter band of ± 10 %. The limit of the combined method is shown for an industrial assembly welded with eight overlap welds. For this joint geometry, a conventional numerical approach was applied, since no analytical solution was actually available. The final simulation results matched the experimental data within a scatter band of ± 10 %. The results of this work provide a comprehensive method to accelerate the calibration of the thermal model of the structure welding simulation of complex and large welded assemblies, even though within limitation. In the future, the implementation of this method in a welding simulation tool accessible to a typical industrial user still has to be done. T3 - BAM Dissertationsreihe - 108 KW - Schweißen KW - industrielle Anwendung KW - Simulation KW - analytische Lösung KW - komplexe Geometrie PY - 2013 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-505 SN - 978-3-9815944-0-9 SN - 1613-4249 VL - 108 SP - 1 EP - 183 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-50 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Oberleitner, Lidia T1 - Immunochemical determination of caffeine and carbamazepine in complex matrices using fluorescence polarization N2 - Pharmacologically active compounds are omnipresent in contemporary daily life, in our food and in our environment. The fast and easy quantification of those substances is becoming a subject of global importance. The fluorescence polarization immunoassay (FPIA) is a homogeneous mix-and-read format and a suitable tool for this purpose that offers a high sample throughput. Yet, the applicability to complex matrices can be limited by possible interaction of matrix compounds with antibodies or tracer. Caffeine is one of the most frequently consumed pharmacologically active compounds and is present in a large variety of consumer products, including beverages and cosmetics. Adverse health effects of high caffeine concentrations especially for pregnant women are under discussion. Therefore, and due to legal regulations, caffeine should be monitored. Automated FPIA measurements enabled the precise and accurate quantification of caffeine in beverages and cosmetics within 2 min. Samples could be highly diluted before analysis due to high assay sensitivity in the low μg/L range. Therefore, no matrix effects were observed. The antiepileptic drug carbamazepine (CBZ) is discussed as a marker for the elimination efficiency of wastewater treatment plants and the dispersion of their respective effluents in surface water. The development of a FPIA for CBZ included the synthesis and evaluation of different tracers. Using the optimum tracer CBZ-triglycine-5-(aminoacetamido) fluorescein, CBZ concentrations in surface waters could be measured on different platforms: one sample within 4 min in tubes or 24 samples within 20 min on microtiter plates (MTPs). For this study, a commercially available antibody was used, which led to overestimations with recovery rates up to 140% due to high cross-reactivities towards CBZ metabolites and other pharmaceuticals. For more accurate CBZ determination, a new monoclonal antibody was produced. In this attempt, methods for improving the monitoring during the production process were successfully applied, including feces screening and cell culture supernatant screening with FPIA. The new monoclonal antibody is highly specific for CBZ and showed mostly negligible cross-reactivities towards environmentally relevant compounds. Measurements at non-equilibrium state improved the sensitivity and selectivity of the developed FPIA due to slow binding kinetics of the new antibody. Additionally, this measure enables for CBZ determination over a measurement range of almost three orders of magnitude. The comprehensively characterized antibody was successfully applied for the development of sensitive homogeneous and heterogeneous immunoassays. The new antibody made the development of an on-site measurement system for the determination of CBZ in wastewater possible. After comprehensive optimization, this automated FPIA platform allows the precise quantification of CBZ in wastewater samples only pre-treated by filtration within 16 min. Recovery rates of 61 to 104% were observed. Measurements in the low μg/L range are possible without the application of tedious sample preparation techniques. Different FPIA platforms including MTPs, cuvettes and tubes were successfully applied. For the choice of the right format, the application field should be considered, e.g. desired sample throughput, usage for optimization or characterization of antibodies or if a set-up for routine measurements is sought for. For high sample throughput and optimization, FPIA performance on MTPs is advantageous. The best results for the application to real samples were obtained using kinetic FP measurements in cuvettes. T3 - BAM Dissertationsreihe - 154 KW - Antibody KW - Coffee KW - ELISA KW - Fluorophore tracer KW - Wastewater PY - 2016 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-392506 SN - 978-3-9818270-2-6 SN - 1613-4249 VL - 154 SP - 1 EP - 124 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-39250 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -