TY - CONF A1 - Kern, Simon A1 - Gräßer, Patrick A1 - Zientek, Nicolai A1 - Maiwald, Michael T1 - First steps towards field integration of benchtop NMR spectroscopy for online monitoring and process control N2 - Online monitoring and process control requires fast and noninvasive analytical methods, which are able to monitor the concentration of reactants in multicomponent mixtures with parts-per-million resolution. Online NMR spectros-copy can meet these demands when flow probes are directly coupled to reactors, since this method features a high linearity between absolute signal area and sample concentration, which makes it an absolute analytical com-parison method being independent on the matrix. Due to improved magnet design and field shimming strategies portable and robust instruments have been introduced to the market by several manufacturers during the last few years. First studies with this technology showed promising results to monitor chemical reaction in the laboratory. T2 - 11. Kolloquium Arbeitskreis Prozessanalytik CY - Wien, Austria DA - 30.11.2015 KW - Online NMR Spectroscopy KW - Smart Sensors KW - Prozess-Spektroskopie KW - Process Analytical Technology KW - Process control PY - 2015 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-388411 SP - 43 EP - 44 AN - OPUS4-38841 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ye, S. A1 - Loll, B. A1 - Berger, A. A1 - Mülow, Ulrike A1 - Alings, C. A1 - Wahl, M. A1 - Koksch, B. T1 - Fluorine teams up with water to restore inhibitor activity to mutant BPTI N2 - Introducing fluorine into molecules has a wide range of effects on their physicochemical properties, often desirable but in most cases unpredictable. The fluorine atom imparts the C–F bond with low polarizability and high polarity, and significantly affects the behavior of neighboring functional groups, in a covalent or noncovalent manner. Here, we report that fluorine, present in the form of a single fluoroalkyl amino acid side chain in the P1 position of the well-characterized serine-protease inhibitor BPTI, can fully restore inhibitor activity to a mutant that contains the corresponding hydrocarbon side chain at the same site. High resolution crystal structures were obtained for four BPTI variants in complex with bovine b-trypsin, revealing changes in the stoichiometry and dynamics of water molecules in the S1 subsite. These results demonstrate that the introduction of fluorine into a protein environment can result in “chemical complementation” that has a significantly favorable impact on protein–protein interactions. KW - serine-protease inhibitor KW - crystal structures KW - Peptide synthesis PY - 2015 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-358987 DO - https://doi.org/10.1039/C4SC03227F IS - 9 SP - 5246 EP - 5254 PB - Royal Society of Chemistry CY - Cambridge AN - OPUS4-35898 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gaal, Mate A1 - Bartusch, Jürgen A1 - Dohse, Elmar A1 - Schadow, Florian A1 - Köppe, Enrico T1 - Focusing of ferroelectret air-coupled ultrasound transducers N2 - Air-coupled ultrasound has been applied increasingly as a non-destructive testing method for lightweight construction in recent years. It is particularly appropriate for composite materials being used in automotive and aviation industry. Air-coupled ultrasound transducers mostly consist of piezoelectric materials and matching layers. However, their fabrication is challenging and their signal-to-noise ratio often not sufficient for many testing requirements. To enhance the efficiency, air-coupled ultrasound transducers made of cellular polypropylene have been developed. Because of its small density and sound velocity, this piezoelectric ferroelectret matches the small acoustic impedance of air much better than matching layers applied in conventional transducers. In our contribution, we present two different methods of spherical focusing of ferroelectret transducers for the further enhancement of their performance in NDT applications. Measurements on carbon-fiber-reinforced polymer (CFRP) samples and on metal adhesive joints performed with commercially available focused air-coupled ultrasound transducers are compared to measurements executed with self-developed focused ferroelectret transducers. T2 - 42nd Annual Review of Progress in Quantitative Nondestructive Evaluation CY - Minneapolis, Minnesota, USA DA - 26.07.2015 KW - Focusing KW - Ferroelectret KW - Air-coupled KW - Transducer KW - Ultrasonic PY - 2015 AN - OPUS4-35957 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maiwald, Michael T1 - Forschung und Entwicklung für Prozessanalytik und Automatisierung in der Prozessindustrie N2 - Neue Prozess-Sensoren für neue Produktionskonzepte. Wie entsteht Innovation? Forschungsimpulse aus der Technologie-Roadmap „Prozess-Sensoren 2015+“. Herausforderungen durch das Zukunftsprojekt „Industrie 4.0“. Technologie-Roadmap „Prozess-Sensoren 4.0“ T2 - ACHEMA 2015: Automation im Dialog – Meet the experts CY - Frankfurt a. M., Germany DA - 15.06.2015 KW - Industrie 4.0 KW - Smart Sensors KW - Smarte Sensoren KW - Process Analytical Technology KW - Prozessanalytik PY - 2015 AN - OPUS4-36142 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN T1 - Forschungsprogramm 2015 - 2017 N2 - Globalisierung und die beschleunigte technologische Entwicklung bringen heute für die Industrieländer Herausforderungen im Hinblick auf Wachstum, Beschäftigung und Strukturwandel mit sich, denen nur mit einer entsprechenden Innovationsdynamik und -dichte begegnet werden kann. Grundvoraussetzung hierfür ist eine leistungsfähige Forschung und Entwicklung ebenso wie Wissens- und Technologietransfer zur Umsetzung von Forschungsergebnissen in marktfähige Produkte und Dienstleistungen. Europa hat sich im Rahmen des Lissabon-Prozesses zum Ziel gesetzt, den Anteil der Forschungsausgaben am Bruttoinlandsprodukt auf 3 % zu steigern. Um die Forschungsinfrastruktur in der Bundesrepublik zu stärken und global wettbewerbsfähig zu bleiben, hat die Bundesregierung mit der Hightech-Strategie einen weiteren wichtigen Schritt zur Förderung des wissenschaftlich-technischen Fortschritts in Deutschland getan. Forschungsprogramme sind sowohl für Forschungseinrichtungen als auch für Mittelgeber ein wichtiges Instrument für die Darstellung und Steuerung ihrer Aktivitäten. Dies gilt auch für die Bundeseinrichtungen mit Forschungs- und Entwicklungsaufgaben, zu denen die Bundesanstalt für Materialforschung und -prüfung (BAM) zählt. Die BAM verfügt über einen klaren gesetzlichen Auftrag für die Sicherheit in Technik und Chemie. Ihre Forschung ist mit der Wahrnehmung öffentlicher Aufgaben verbunden. Das Forschungsprogramm zeigt Perspektiven im Bereich ihres Aufgabenfeldes sowie ihrer damit verbundenen Forschungsaktivitäten transparent und politisch nutzbar auf und dient darüber hinaus der Koordinierung der Ressortforschung. Das Forschungsprogramm der BAM wird alle zwei Jahre aktualisiert. Es gibt einen Überblick über die aktuellen und zukünftigen Forschungsthemen und die hierfür erforderlichen Rahmenbedingungen. PY - 2015 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-421401 SP - 1 EP - 40 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-42140 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dippong, Martin A1 - Gürnth-Marschner, C. A1 - Kirschbaum, M. A1 - Duschl, C. A1 - Schneider, Rudolf A1 - Kuhne, Maren A1 - Hoffmann, Katrin T1 - Fraunhofer Life Science Day N2 - Their high affinity, selectivity and specificity make monoclonal antibodies (mAbs) very important tools in research, diagnostics and therapy. The production of mAbs is routinely performed by hybridoma technique. Hybridomas are generated by fusing antibody-producing B cells with indefinitely proliferating myeloma cells. Both, cell fusion and the indispensable identification and isolation of the desired antibody-producing hybridoma clone is still far from being trivial. We describe a novel method that should help to optimize the cell fusion, and the screening for antibody-secreting hapten-specific hybridoma cells by using fluorescence activated cell sorting and single-cell fusion. Hybridoma cells specific for a hapten were incubated with a hapten-peroxidase conjugate (hapten-HRP), which was subsequently incubated with a fluorophore-labeled polyclonal anti-peroxidase antibody (anti-HRP-Alexa Fluor® 488). To characterize the expression of membrane-bound immunoglobulin G (IgG) a fluorophore-labeled anti-mouse IgG antibody (anti-IgG-Alexa Fluor® 647) was used. Successful staining was verified by confocal laser scanning microscopy (CLSM). We show that it is possible to specifically label hapten-specific hybridoma cells. It should also be possible to use this labelling approach for the isolation of hapten-specific B cells from the spleen and use these cells for single-cell fusion. Parallelized cell fusion chips were developed to increase fusion efficiencies. T2 - Fraunhofer Life Science Day 2015 CY - Leipzig, Germany DA - 03.07.2015 KW - Single-cell fusion KW - Hybridoma KW - Monoclonal antibodies PY - 2015 AN - OPUS4-37872 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mery, D. A1 - Riffo, V. A1 - Zscherpel, Uwe A1 - Mondragon, G. A1 - Lillo, I. A1 - Zuccar, I. A1 - Lobel, H. A1 - Carrasco, M. T1 - GDXray: The Database of X-ray Images for Nondestructive Testing N2 - In this paper, we present a new dataset consisting of 19,407 X-ray images. The images are organized in a public database called GDXray that can be used free of charge, but for research and educational purposes only. The database includes five groups of X-ray images: castings, welds, baggage, natural objects and settings. Each group has several series, and each series several X-ray images. Most of the series are annotated or labeled. In such cases, the coordinates of the bounding boxes of the objects of interest or the labels of the images are available in standard text files. The size of GDXray is 3.5 GB and it can be downloaded from our website. We believe that GDXray represents a relevant contribution to the X-ray testing community. On the one hand, students, researchers and engineers can use these X-ray images to develop, test and evaluate image analysis and computer vision algorithms without purchasing expensive X-ray equipment. On the other hand, these images can be used as a benchmark in order to test and compare the performance of different approaches on the same data. Moreover, the database can be used in the training programs of human inspectors. KW - Data base KW - NDT KW - RT KW - Digital image catalogues KW - Security PY - 2015 DO - https://doi.org/10.1007/s10921-015-0315-7 SN - 0195-9298 VL - 34 IS - 4 SP - 34 EP - 42 PB - Springer Verlag CY - Heidelberg AN - OPUS4-37732 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Niederleithinger, Ernst A1 - Abraham, O. A1 - Mooney, M. T1 - Geophysical methods in civil engineering: Overview and new concepts N2 - Geophysical methods have been used in civil engineering for decades. The main field of application is - to no surprise – in geotechnical projects from site characterization to foundation quality assurance. For more than 25 years, ground penetrating radar (GPR) and seismic methods have found applications in structural engineering. Recently introduced geophysical methods have been adopted to ultrasonic investigations in various fields. They help to improve the quality of structural imaging and to detect small changes in concrete. An overview of the history and current use of geophysics in civil engineering is given. Selected examples of new concepts include advances in wave based imaging, quality assurance for foundations, detecting small changes in concrete as well as moisture and corrosion detection are discussed. T2 - NDT-CE 2015 - International symposium non-destructive testing in civil engineering CY - Berlin, Germany DA - 15.09.2015 KW - Nondestructive testing KW - Civil engineering KW - Geophysics PY - 2015 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-344666 UR - https://www.ndt.net/?id=18260 SN - 1435-4934 VL - 20 IS - 11 SP - 1 EP - 6 PB - NDT.net CY - Kirchwald AN - OPUS4-34466 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pauli, Jutta A1 - Wycisk, V. A1 - Welker, P. A1 - Justies, A. A1 - Resch-Genger, Ute A1 - Haag, R. A1 - Licha, K. T1 - Glycerol-Based Contrast Agents: A Novel Series of Dendronized Pentamethine Dyes N2 - The synthesis of water-soluble dyes, which absorb and emit in the range between 650 and 950 nm and display high extinction coefficients (ε) as well as high fluorescence quantum yields (Φf), is still a demand for optical imaging. We now present a synthetic route for the preparation of a new group of glycerol-substituted cyanine dyes from dendronized indole precursors that have been functionalized as Nhydroxysuccinimide (NHS) esters. High Φf values of up to 0.15 and extinction coefficients of up to 189 000 L mol−1 cm−1 were obtained for the pure dyes. Furthermore, conjugates of the new dendronized dyes with the antibody cetuximab (ctx) that were directed against the epidermal growth factor receptor (EGFR) of tumor cells could be prepared with dye to protein ratios between 0.3 and 2.2 to assess their potential as imaging probes. For the first time, ctx conjugates could be achieved without showing a decrease in Φf and with an increasing labeling degree that exceeded the value of the pure dye even at a labeling degree above 2. The incorporation of hydrophilically and sterically demanding dendrimers into cyanines prevented dimer formation after covalent conjugation to the antibody. The binding functionality of the resulting ctx conjugates to the EGFR was successfully demonstrated by cell microscopy studies using EGFR expressing cell lines. In summary, the combination of hydrophilic glycerol dendrons with reactive dye labels has been established for the first time and is a promising Approach toward more powerful fluorescent labels with less dimerization. KW - Dye KW - Quantum yield KW - Fluorescence KW - Contrast agent KW - Extinction coefficient PY - 2015 DO - https://doi.org/10.1021/acs.bioconjchem.5b00097 SN - 1043-1802 VL - 26 SP - 773 EP - 781 PB - ACS Publications CY - Washington AN - OPUS4-38880 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heck, Christian A1 - Bald, Ilko A1 - Prinz, J. A1 - Merk, V. A1 - Kneipp, Janina T1 - Gold nanolenses on DNA origami substrates for surface-enhanced Raman scattering N2 - Surface-enhanced Raman scattering (SERS) exploits the enhancement of electromagnetic fields in close vicinity of plasmonic nanostructures, enabling characterization of analytes at the single-molecule level. The nanometer-scale spatial arrangement of plasmonic metal nanoparticles and analyte molecules has a significant effect on the observed signal enhancements and represents a great challenge in this technique. In our work, DNA origami is used as platform for precise positioning of gold nanoparticles (AuNPs). Especially high sensitivities are expected for gold nanolenses (AuNLs), consisting of rows of three or more differently-sized AuNPs. We assembled different AuNL designs and determined respective SERS enhancement factors by collecting Raman spectra from single AuNLs. Finite difference time domain calculations estimate attainable electromagnetic field enhancements. Ultimately, we aim to develop a versatile platform for various SERS applications. T2 - DNA meets Plasmonics Konferenz CY - Bad Honnef, Germany DA - 07.12.2015 KW - DNA origami KW - SERS KW - Plasmonics PY - 2015 AN - OPUS4-35906 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wang, X. A1 - Pauli, Jutta A1 - Resch-Genger, Ute A1 - Niessner, R. A1 - Knopp, D. T1 - Gold nanoparticle-catalyzed uranine reduction N2 - Gold nanoparticles (AuNPs) can catalyze the decolorization of organic dyes in the presence of sodium borohydride (NaBH4), which can be utilized for sensitive optical signaling. Here, we monitor the catalytic reduction of a fluorescent substrate, exemplarily chosen uranine, by AuNPs serving as nanocatalysts by absorption and fluorescence spectroscopy. Dye reduction is accompanied by dramatic changes in the absorption and fluorescence properties of uranine. As proposed reaction mechanism, we assume electron transfer between uranine and NaBH4 through the AuNPs nanocatalysts which is currently investigated also by time-resolved fluorescence and detailed spectroscopic studies of the influence of pH, NaBH4, and AuNPs on these effects. As ultimate goal, a model reporter platform with colorimetric andfluorometric signaling is anticipated for the detection of different analytes by coating AuNPs with affinity ligands such as antibodies and aptamers and and special separation methods. T2 - Anakon 2015 CY - Graz, Austria DA - 23.03.2015 KW - Fluorescence lifetime KW - Uranine KW - Nanoparticle KW - Surfactant PY - 2015 AN - OPUS4-38957 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lempke, L. A1 - Fischer, Tobias A1 - Bell, Jérémy A1 - Kraus, Werner A1 - Rurack, Knut A1 - Krause, N. T1 - Gold-catalyzed allene cycloisomerization for pyrrole synthesis: towards highly fluorinated BODIPY dyes N2 - A novel synthetic strategy toward highly fluorinated BODIPY dyes with exceptional photostabilities relying on sustainable gold catalysis has been developed. A key to the tailored pyrrole precursors is the gold catalysis performed in ionic liquids as the reaction medium, allowing a facile recycling of the catalysts. The dyes prepared are well-matching with the spectral windows of popular rhodamine dyes and possess high brightness while showing a distinctly higher photostability than the rhodamines especially in aprotic solvents. KW - Gold-Katalyse KW - BODIPY-Farbstoffe KW - Photostabilität KW - Fluor-Substitution KW - Fluoreszenz PY - 2015 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-344692 DO - https://doi.org/10.1039/c4ob02671c SN - 1477-0520 SN - 1477-0539 VL - 13 IS - 12 SP - 3787 EP - 3791 PB - RSC CY - Cambridge AN - OPUS4-34469 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Dariz, P. A1 - Schmid, Thomas T1 - Granulierte Hochofenschlacke als Mörtelzuschlag im 19. Jahrhundert in der Schweiz N2 - Als schweizweit einziger Hersteller produzierte die Gesellschaft der Ludwig von Roll'schen Eisenwerke seit den 1870er Jahren granulierte Hochofenschlacke. Im Blashochofen von Choindez im Schweizer Jura wird bis Mitte der 1920er Jahre Bohnerz aus dem Delsberger Becken, das kontemporär publizierten Analysen zufolge als Spuren- bzw. Schwermetalle Titan, Chrom, Blei und Vanadium enthält, zu grauem Roheisen verhüttet. In zementgebundenen Mörtelmischungen des 19. und frühen 20. Jahrhunderts aus verschiedenen Regionen der Schweiz finden sich neben reliktischen Hüttensandsplittern vereinzelt bis zu fünfhundert Mikrometer große scharze Kugeln mit grünlichem Schimmer, wohl nicht gemahlener Schlackensand. Deren mittels Ramanmikroskopie (Phasenbestand) und energiedispersiver Röntgenspektroskopie am Rasterelektronenmikroskop (Elementanalytik) ermittelte Mineralogie ergibt in Form von Plattnerit PbO2, Rutil TiO2 und vermitlich Chromit Fe(II)Cr2O4 bzw. Nichromit (Ni,Co,Fe(II))(Cr,Fe(III),Al)2)4 Übereinstimmungen mit den nur die Elementzusammensetzung berücksichtigenden historischen Resultaten. Ebenfalls im Zusammenhang mit dem das Bohnerz begleitenden Boluston samt Huppererde zu sehen sind die Minerale Coelestin SrSO4 und Zirkon ZrSiO4, des Weiteren der Siliciumcarbidpolymorph Moissanit SiC als Reaktionsprodukt von Quarzsand und Brennstoff. Die Kohärenz zwischen um die Jahrhundertwende durchgeführten Analysen von Rohmaterial als auch Ofenbruch aus dem in Choindez betriebenen Hochofen und den in diesem Beitrag diskutierten Resultaten moderner analytischer Methoden spricht für den Gebrauch von granulierter Schlacke aus dem Hause Ludwig von Roll als Mörtelzuschlag. Die Hüttensandkörner, eigentlich latent hydraulisch, sind aufgrund der fehlenden Aufbereitung zu grob für eine effektive Hydratation und deshalb trotz reaktiver Glasphase und Klinkermineralien (Belit Ca2SiO4 und Monocalciumaluminat CaAl2O4) intakt in der Bindemittelmatrix erhalten. N2 - From the 1870s the Ludwig von Roll ironworks produced granulated blast furnace slag in Choindez (Jura, Switzerland) as a by-product of the smelting of bean ore excavated until 1926 in the Delsberg Basin. According to historical analyses, this iron ore deposit contais heavy and trace metals such as titanium, chromium, lead and vanadium. In mortar samples from different regions of Switzerland originating from the 19th and early 20th centuries, residues of granulated blast furnace slag are observable as angular glassy particles in the binder matrix. In addition, black spherical grains with greenish lustre (up to 500 micrometres in diameter), probably not ground granulated blast furnace slag, can be distinguished sporadically in thin sections. Raman microscopy as well as scanning electron microscopy coupled with energy dispersive X-ray spectroscopy (SEM-EDX) measurements have revealed, inter alia, the presence of the crystalline components plattnerite PbO2, rutile TiO2 and presumably chromite Fe(II)Cr2O4 or nichromite (Ni,Co,Fe(II))(Cr,Fe(III),Al)2O4. These findings are consistent with historical analyses, which were restricted to the determination of the elemental (not phase) composition of the raw material processed by the Ludwig von Roll ironworks. Furthermore the minerals celestine SrSO4 and zircon ZrSiO4 can be linked to bean ore and bole from Delsberg, and likewise the silicon carbide moissanite SiC, which is a reaction product of quartz sand and coke. The coherence if the results of historical chemical analyses and of modern microscopic imaging and spectroscopy methods described here pinpoints the Ludwig von Roll ironworks as the most probable supplier of the granulated blast furnace slag that was added to the mortars under investigation. The unreacted remnants exhibit defined boundaries; no hydration rims are observable despite the glassy nature of the latent hydraulic aggregate, which contains cement clinker minerals (belite and calcium aluminate) as crystalline components. Not finely ground, the spheroids are too coarse for an effective hydration reaction and act as inert filler. KW - Granulierte Hochofenschlacke KW - Raman Mikroskopie KW - REM-EDX KW - Granulated blast furnace slag KW - Raman microscopy KW - SEM-EDX PY - 2015 VL - 29 IS - 2 SP - 293 EP - 304 PB - Wernersche Verlagsgesellschaft mbH CY - Worms AN - OPUS4-36651 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Noordmann, J. A1 - Richter, Silke A1 - Kipphardt, Heinrich A1 - Kaltenbach, A. A1 - Görlitz, V. A1 - Rienitz, O. T1 - Gravimetric preparation and characterization of a primary reference solution of molybdenum N2 - Gravimetrically prepared mono-elemental reference solutions having a well-known mass fraction of approximately 1 g/kg define the very basis of virtually all measurements in inorganic analysis. Serving as the starting materials of all standard/calibration solutions, they link virtually all measurements of inorganic analytes to the purity of the solid materials they were prepared from. In case these solid materials are characterized comprehensively with respect to their purity, this link also establishes direct metrological traceability to The International System of Unit. Within the framework of the European Metrology Research Programme (EMRP), in the Joint Research Project called SIB09 Primary standards for challenging elements, a reference solution of molybdenum was prepared directly from the respective metal with a relative expanded uncertainty associated with the mass fraction of Urel(w) < 0.05 %. A highly accurate and precise ICP OES and MC-ICP-MS method was developed to assist with the preparation and as a dissemination tool. T2 - ANACON CY - Graz, Austria DA - 23.03.2015 KW - Metrology KW - Primary standards KW - Mo PY - 2015 AN - OPUS4-38038 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Trela, Christiane A1 - Kind, Thomas A1 - Günther, Martin T1 - Ground penetrating radar in reflection vs transmission mode for void detection in concrete structures N2 - The concreting of prefabricated concrete structures can lead to insufficient bonding or even to remaining cavities. Honeycombs (aggregate clusters without cement) represent potential weakening of the structure and need to be detected non-destructively. In our study we tested the capability of ground penetrating radar (GPR) techniques for this purpose. We applied GPR in reflection mode and zero-offset profiling (ZOP) transmission mode on a precast concrete twin wall with built-in honeycombs. GPR measurements were performed as two channel measurement with ground coupled antennas with centre frequencies of 1.5 GHz and 2.6 GHz mounted to an automated scanner system. Our findings show that ZOP transmission measurements are a more efficient method to detect voids in reinforced concrete structures compared to reflection mode measurements. This holds for both the effort needed for the measurement and the evaluation as well as the validity of the data. Honeycombs (basically representing voids) are usually characterized by strongly reduced amplitudes and earlier arrivals of the transmitted wave. T2 - International Symposium Non-Destructive Tesing in Civil Engineering (NDT-CE 2015) CY - Berlin, Germany DA - 15.09.2015 KW - Void detection KW - Ground penetrating radar KW - Reflection KW - Transmission KW - Reinforced concrete KW - Prefabricated wall PY - 2015 AN - OPUS4-40005 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Trela, C. A1 - Kind, Thomas A1 - Günther, Martin T1 - Ground penetrating radar in reflection vs transmission mode for void detection in concrete structures N2 - The concreting of prefabricated concrete structures can lead to insufficient bonding or even to remaining cavities. Honeycombs (aggregate clusters without cement) represent potential weakening of the structure and need to be detected non-destructively. In our study we tested the capability of ground penetrating radar (GPR)techniques for this purpose. We applied GPR in reflection mode and zero-offset profiling (ZOP) Transmission mode on a precast concrete twin wall with built-in honeycombs. GPR measurements were performed as twochannel measurement with ground coupled antennas with centre frequencies of 1.5 GHz and 2.6 GHz mounted to an automated scanner system. Our findings show that ZOP transmission measurements are a more efficient method to detect voids in reinforced concrete structures compared to reflection mode measurements. This holds for both the effort needed for the measurement and the evaluation as well as the validity of the data. Honeycombs (basically representing voids) are usually characterized by strongly reduced amplitudes and earlier arrivals of the transmitted wave. T2 - NDT-CE 2015 - International symposium non-destructive testing in civil engineering CY - Berlin, Germany DA - 15.09.2015 KW - Ground penetrating radar KW - Reflection KW - Transmission KW - Reinforced concrete KW - Prefabricated wall KW - Void detection PY - 2015 SN - 1435-4934 SP - 324 EP - 344 PB - Technische Universität Berlin / Bundesanstalt für Materialforschung und -prüfung CY - Berlin, Germany AN - OPUS4-40006 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Denkler, Tilman T1 - Guest lecture: Quality infrastructure & sustainability N2 - Gastvortrag an der TU Berlin zu Qualitätsinfrastruktur und Nachhaltigkeit, gehalten im Rahmen der Veranstaltungsreihe Sustainable Innovation N2 - Guest lecture at the TU Berlin on quality infrastructure and sustainability, held as part of the Sustainable Innovation lecture series. T2 - Guest lecture at Sustainable Innovation - WS 2015/2016 CY - TU Berlin, Berlin, Germany DA - 01.12.2015 KW - Quality infrastructure KW - Sustainability PY - 2015 AN - OPUS4-41699 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hielscher, Stefan A1 - Beck, Uwe A1 - Lange, Thorid A1 - Weise, Matthias T1 - Haftfestigkeit optischer und ophthalmischer Schichten auf Polymeren und Glas T1 - Adhesive strength of optical coatings on glass and ophthalmic coatings on polymers N2 - Die quantitative Bestimmung der Haftfestigkeit von Beschichtungen ist von entscheidender Bedeutung sowohl für die Entwicklung als auch für die Qualitätssicherung. In einer Vergleichsstudie zur Haftfestigkeit von optischen und ophthalmischen Schichten wurde mit Hilfe der Zentrifugentechnologie der Einfluss verschiedener Parameter (Substratdicke, Oberflächenvorbehand-lung, Haftvermittler) auf die Haftfestigkeit optischer Schichten auf silikatischen und ophthalmischer Schichten auf polymeren Substraten untersucht. Zur Bestimmung der Haftfestigkeit in der physikalisch korrekten Dimension Kraft pro Fläche im Stirnabzug stehen die Ein-Proben-Prüfung mit der Zugprüfmaschine und die Mehr-Proben-Prüfung mittels Zentri- fugentechnologie zur Verfügung. Die Zentrifugentechnologie wurde ausgewählt, da die Prüfung von bis zu acht Proben unter nahezu identischen Versuchsbedingungen und somit eine statistisch gesicherte Bestimmung der Haftfestigkeit möglich sind. Es konnte nachgewiesen werden, dass die Substratdicke einen erheblichen Einfluss auf die gemessene Haftfestigkeit hat. Dies entspricht den Erwartungen, da es sich bei der Haftfestigkeit um eine System- eigenschaft des Schicht-Substrat-Systems handelt. Bei den Delaminationsbrüchen (DF) konnte zwischen Delamination des metallischen Reflektors (DF-R) und Delamination des Dielektrikums (DF-D) unter- schieden werden. Im Fall hinreichender Haftfestigkeit der Beschichtung traten auch Adhäsionsbrüche am Interface zum und Kohäsionsbrüche im Klebstoff auf. Nachfolgende Untersuchungen werden sich mit alternativen Klebstoffen und weiterentwickelten Fügestrategien befassen. N2 - The quantitative determination of adhesive strength of coatings is essential for both R&D and quality assurance. In a comparative study on adhesive strength of optical and ophthalmic coatings, centrifuge technology has been used for the investigation of the influence of certain parameters (e.g. substrate thickness, surface-pretreatment and adhesion promoters) on adhesive strength of optical coatings on silicate and ophthalmic coatings on polymer substrates. For determination of adhesive strength in the correct dimension force per area in the pull-off test, only two tests are available, the single-sample test in a tensile testing machine and the multi-sample test by means of centrifuge technology. The centrifuge technology has been chosen because up to eight samples can be tested under almost identical testing conditions at the same time. Hence, a statistical evaluation of adhesive strength is feasible. It has been shown that substrate thickness has a remarkable influence on the measured adhesive strength. This fulfils the expectations as adhesive strength is a system property of the coating-substrate system. Regarding delamination failure (DF) it could be differentiated between the delamination of reflective coatings (DF-R) and delamination of dielectric coatings (DF-D). In case of sufficient adhesive strength of the coating, adhesion failure at the interface of and cohesion failure within the adhesive were also observed. Following studies will address alternative adhesives and advanced bonding strategies. T2 - Werkstoffprüfung 2015 CY - Bad Neuenahr, Germany DA - 03.12.2015 KW - Haftfestigkeit KW - Optische Schichten KW - Ophthalmische Schichten KW - Zentrifugentechnologie KW - Mehr-Proben-Prüfung PY - 2015 AN - OPUS4-37022 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stroh, Julia A1 - Nguyen, Thi Yen A1 - Emmerling, Franziska T1 - High resolution in situ monitoring of the initial cement hydration influenced by organic admixtures N2 - Numerous admixtures are used in the building practice to customize the properties of the cement paste during application. The influences of admixtures on the course of cement hydration and formation of hydrate phases have to be considered. Polycarboxylate ether (PCE) based polymeric superplasticizers (SPs) are known to retard the setting of the cement paste. The extent of the retardation differs depending on the molecular structure of the SP. Additionally, the presence of a stabilizing agent (SA) in the cement paste has a retarding side effect on the setting. The initial cement hydration processes and the detailed mechanisms of the retardation influenced by PCEs, as well as their interactions with particular SAs, are insufficiently understood. Up to now, only the results of phenomenological studies were taken into account to describe this retardation process. A detailed structure analysis monitoring the change of the phase composition during the hydration was never applied. Both SP and SA affect the adsorption of the sulphate ions on the clinker particles, causing changes in the formation of ettringite during the initial hydration, and are therefore a crucial part of the setting process itself. Here, the initial hydration of cement influenced by the interaction of SP and SA was monitored in situ by synchrotron X-ray diffraction. The high time resolution of the measurements allowed a continuous detection of the hydrates formed. The hydration was followed from the starting point of water addition and for couple of hours afterwards. The hydration of the levitated cement pellets containing starch as SA was initialized by adding aqueous solutions of different commercial SPs. Changes in the ettringite formation were detected in comparison to the reference hydration of pure cement. T2 - Early Age Concrete: From the Research Lab to the Construction Site CY - Tomsk, Russia DA - 02.06.2015 KW - Portland cement KW - Initial hydration KW - Superplasticizer KW - Stabilizer KW - Synchrotron XRD PY - 2015 AN - OPUS4-35470 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kardjilov, N. A1 - Hilger, A. A1 - Manke, I. A1 - Banhart, J. A1 - Griesche, Axel T1 - Imaging with Cold Neutrons at the CONRAD-2 Facility N2 - CONRAD-2 is an imaging instrument using low-energy (cold) neutrons. The instrument is installed at the end of a curved neutron guide which avoids the direct line of sight towards the reactor core. This ensures a very low background of high-energy neutrons and. photons at the sample position. The cold neutron beam provides a wavelength range which is suitable for phase-and diffraction-contrast imaging such as grating interferometry and Bragg edge mapping. The instrument is well suited for high resolution imaging due to the high efficiency of the very thin scintillators that can be used for the detection of cold neutrons. An instrument upgrade was performed recently as a part of an upgrade program for the cold neutron instrumentation at HZB. The parameters of the instrument as well as some research highlights will be presented. T2 - 10th World Conference on Neutron Radiography (WCNR) CY - Grindelwald, SWITZERLAND DA - 05.10.2014 KW - iron embrittlement KW - neutron imaging KW - neutron instrumentation KW - cold neutrons PY - 2015 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-373239 DO - https://doi.org/10.1016/j.phpro.2015.07.008 SN - 1875-3892 VL - 69 SP - 60 EP - 66 PB - Elsevier B.V. CY - Amsterdam, NL AN - OPUS4-37323 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -