TY - JOUR A1 - Gebauer, D. A1 - Gutiérrez, R, A1 - Marx, S. A1 - Butler, M. A1 - Grahl, K. A1 - Thiel, T. A1 - Maack, Stefan A1 - Küttenbaum, Stefan A1 - Pirskawetz, Stephan A1 - Breit, W. A1 - Schickert, M. A1 - Krüger, M. T1 - Interrelated dataset of rebound numbers, ultrasonic pulse velocities and compressive strengths of drilled concrete cores from an existing structure and new fabricated concrete cubes N2 - Two test series were examined using nondestructive measuring methods by six independent laboratories before determining their compressive strength. The nondestructive test methods used were the rebound hammer and ultrasonic pulse velocity measurement. Two types of geometries were investigated: drilled cores and cubes. The measurement procedure for each of these datasets is conditioned to the geometry and is therefore different. The first series consists of 20 drilled cores (approximately diameter/height = 10 cm/20 cm) from the 55-year-old Lahntal Viaduct near Limburg, Germany. After preparation in the first laboratory, the lateral surface of the drilled cores was tested with the rebound hammer using a given pattern. Every laboratory tested every drilled core at different locations. Ultrasonic measurements in transmission were performed repeatedly at predefined points on the flat surfaces of the specimen. The second series consisted of 25 newly manufactured concrete cubes of a mix with a target concrete strength class of C30/37. The edge length was 15 cm. Each laboratory received five specimens of this test series. Thus, contrary to the first series, each specimen was tested by only one laboratory. Two side faces of each cube were tested with the rebound hammer. In addition, ultrasonic measurements were performed by one laboratory. The time of flight was measured between the tested side faces of the rebound hammer at different positions. For both series, rebound hammers were used to determine the R-value as well as the Q-value. The rebound hammer models within the laboratories were always the same, while they differed between the laboratories. The ultrasonic measurements took place with different measurement systems and couplants. Finally, both specimen series were tested destructively for compressive strength. The dataset contains the raw data summarized in tabular form. In addition, relevant calculated data are included in some cases. For the ultrasonic measurements, the time of flight has already been converted into the ultrasonic velocity. Besides, in addition to the raw data of the compressive strength test (force, weight, and geometry values), the calculated compressive strengths and densities are also provided. KW - Nondestructive testing KW - Ultra sound KW - Rebound hammer KW - Existing structure KW - Civil engineering PY - 2023 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-574655 DO - https://doi.org/10.1016/j.dib.2023.109201 SN - 2352-3409 VL - 48 IS - 109201 SP - 1 EP - 13 PB - Elsevier Inc. AN - OPUS4-57465 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bühling, Benjamin A1 - Küttenbaum, Stefan A1 - Maack, Stefan A1 - Strangfeld, Christoph T1 - Development of an Accurate and Robust Air-Coupled Ultrasonic Time-of-Flight Measurement Technique N2 - Ultrasonic time-of-flight (ToF) measurements enable the non-destructive characterization of material parameters as well as the reconstruction of scatterers inside a specimen. The time-consuming and potentially damaging procedure of applying a liquid couplant between specimen and transducer can be avoided by using air-coupled ultrasound. However, to obtain accurate ToF results, the waveform and travel time of the acoustic signal through the air, which are influenced by the ambient conditions, need to be considered. The placement of microphones as signal receivers is restricted to locations where they do not affect the sound field. This study presents a novel method for in-air ranging and ToF determination that is non-invasive and robust to changing ambient conditions or waveform variations. The in-air travel time was determined by utilizing the azimuthal directivity of a laser Doppler vibrometer operated in refracto-vibrometry (RV) mode. The time of entry of the acoustic signal was determined using the autocorrelation of the RV signal. The same signal was further used as a reference for determining the ToF through the specimen in transmission mode via cross-correlation. The derived signal processing procedure was verified in experiments on a polyamide specimen. Here, a ranging accuracy of <0.1 mm and a transmission ToF accuracy of 0.3μs were achieved. Thus, the proposed method enables fast and accurate non-invasive ToF measurements that do not require knowledge about transducer characteristics or ambient conditions. KW - Air-coupled ultrasound KW - Laser Doppler vibrometer KW - Refracto-vibrometry KW - Acousto-optic effect KW - Time-of-flight measurements KW - In-air ranging KW - Non-destructive testing PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-544711 DO - https://doi.org/10.3390/s22062135 VL - 22 IS - 6 SP - 1 EP - 17 PB - MDPI CY - Basel, Switzerland AN - OPUS4-54471 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Maack, Stefan A1 - Küttenbaum, Stefan A1 - Bühling, Benjamin A1 - Niederleithinger, Ernst T1 - Low frequency ultrasonic dataset for pulse echo object detection in an isotropic homogeneous medium as reference for heterogeneous materials in civil engineering N2 - The dataset presented contains ultrasonic data recorded in pulse echo mode. The investigated specimen is made of the isotropic homogeneous material polyamide and has a drill hole of constant diameter running parallel to the surface, which was scanned in a point grid using an automatic scanner system. At each measuring position, a pitch-catch measurement was performed using a sampling rate of 2 MHz. The probes used are arrays consisting of a spatially separated receiving and in-phase transmitting unit. The transmitting and receiving sides each consist of 12 point-shaped single probes. These dry-point contact (DPC) probes operate according to the piezoelectric principle at nominal frequencies of 55 kHz (shear waves) and 100 kHz (longitudinal waves), respectively, and do not require a coupling medium. The measurements are performed with longitudinal (100 kHz) and transverse (55 kHz) waves with different geometric orientations of the probe on the measurement surface. The data presented in the article provide a valid source for evaluating reconstruction algorithms for imaging in the low-frequency ultrasound range. KW - Non-destructive testing KW - Ultrasound KW - Pulse-echo method KW - Reference material KW - Reconstruction algorithm KW - Validation PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-547326 DO - https://doi.org/10.1016/j.dib.2022.108235 VL - 42 SP - 1 EP - 11 PB - Elsevier Inc. AN - OPUS4-54732 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Küttenbaum, Stefan A1 - Maack, Stefan A1 - Taffe, A. T1 - Structural safety referring to ultrasound on concrete bridges N2 - Measuring means knowing. The structural engineer’s Knowledge about structures is vitally important for the assessment of their structural safety. This contribution shows, how non-destructive testing methods can be used to collect valuable Information about existing structures. This value is expressed in this paper by the usability in probabilistic assessments and thus by the reliability of the information. The development of non-destructive testing methods in civil-engineering allows the realistic measurement and visualization of inner constructions of concrete components with a minimum of destructive interventions. The evaluation of the quality of measurement data is of fundamental importance for quantitative measurements in order to ensure the objectivity of testing and evaluation and to assess the reliability of the knowledge acquired. Both systematic and random deviations must be identified, quantified and taken into account to obtain statistically sound data. The Focus of this contribution is on the methodical path, how displayed measurement data can be processed into reliable knowledge. It is not about developing assessment methods but about providing necessary knowledge to increase their operational usability. T2 - 16th International Probabilistic Workshop CY - Vienna, Austria DA - 12.09.2018 KW - NDT KW - Reassessment KW - Probabilistic KW - Non-destructive testing in civil engineering PY - 2018 DO - https://doi.org/10.1002/best.201800034 SN - 1437-1006 VL - 113 IS - S2 SP - 7 EP - 13 PB - Ernst & Sohn Verlag für Architektur und technische Wissenschaften GmbH & Co. KG CY - Berlin AN - OPUS4-46143 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Küttenbaum, Stefan A1 - Maack, Stefan A1 - Braml, T. A1 - Taffe, A. A1 - Haslbeck, M. T1 - Bewertung von Bestandsbauwerken mit gemessenen Daten. Teil 1: Konzept, Messungen und Leistungsfähigkeit der ZfP‐Verfahren N2 - Gegenüber dem Neubauentwurf können bei der Bewertung von bestehender Bausubstanz Sicherheitsreserven genutzt werden, da Unsicherheiten, die beim Bau auftreten können, besser bekannt oder nicht mehr vorhanden sind. Können solche Unsicherheiten genauer bewertet werden, z. B. durch die Feststellung der genauen Lage der Spannglieder bei einer Spannbetonbrücke, so können Sicherheitsbeiwerte reduziert werden, ohne dass es dabei zu Auswirkungen auf das normativ festgelegte Zuverlässigkeitsniveau kommt. Mittlerweile sind Prüfmethoden an Bauwerken wirtschaftlich einsetzbar und auch so leistungsfähig, dass die für die Tragfähigkeit und Gebrauchstauglichkeit wesentlichen Parameter identifiziert werden können. Ein wesentlicher Punkt ist hierbei die Integration derartiger Messergebnisse in Rechenmodelle, die für die Nachrechnung des Bauwerks verwendet werden. Dies können sowohl semiprobabilistische Rechenmodelle als auch vollprobabilistische Modelle sein. Bei semiprobabilistischen Methoden können aus den Messergebnissen Teilsicherheitsbeiwerte berechnet und abgeleitet werden, die dann in den bekannten Nachweisformaten gemäß den Eurocodes und der Nachrechnungsrichtlinie berücksichtigt werden. Bei vollprobabilistischen Nachweisen können die Messdaten in Form von Verteilungsdichtefunktionen mit gemessenen Variationskoeffizienten direkt in das Rechenmodell eingehen. In einer dreiteiligen Aufsatzreihe werden die Messverfahren und die Nutzung der Ergebnisse bei der Nachrechnung vorgestellt. Der vorliegende Teil 1 zeigt die Möglichkeiten des Einsatzes von zerstörungsfreien Prüfverfahren und bewertet deren Leistungsfähigkeit. Messen heißt wissen. Dieses Wissen spiegelt die Realität wider und soll den Tragwerksplaner bei der Entscheidungsfindung über die Sicherheit und Zuverlässigkeit von Bestandsbauwerken unterstützen. KW - Nachrechnung KW - Zerstörungsfreie Prüfung KW - Messunsicherheit KW - Brücken KW - Beton PY - 2019 DO - https://doi.org/10.1002/best.201900002 SN - 1437-1006 VL - 114 IS - 6 SP - 370 EP - 382 PB - Ernst & Sohn Verlag für Architektur und technische Wissenschaften GmbH & Co. KG CY - Berlin AN - OPUS4-48156 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Braml, T. A1 - Wimmer, J. A1 - Varabei, Y. A1 - Maack, Stefan A1 - Küttenbaum, Stefan A1 - Kuhn, T. A1 - Reingruber, M. A1 - Gordt, A. A1 - Hamm, J. T1 - Digitaler Zwilling: Verwaltungsschale BBox als Datenablage über den Lebenszyklus einer Brücke T1 - Digital twin: Asset administration shell BBox as data storage over the life cycle of a bridge N2 - Auf dem Weg zur digitalen Brücke existieren bereits erste Lösungen, die den Lebenszyklus einer Brücke abbilden können. Für die Planung, den Bau und den Unterhalt stehen unterschiedlichste Werkzeuge, z. B. BIM, DIN 1076, SIB-Bauwerke, Monitoring etc. zur Verfügung, die jeweils mit unterschiedlichen Datenformaten arbeiten. Für ein intelligentes Erhaltungsmanagement müssen aber alle Daten mit den verschiedenen Datenformaten zusammengeführt, abgelegt und so verwaltet werden können, dass über den gesamten Lebenszyklus einer Brücke die Abbildung eines ganzheitlichen digitalen Zwillings eines Bauwerks möglich ist. Die Autoren haben dafür mit BBox den Prototyp einer Verwaltungsschale (VWS) auf Grundlage von Industrie 4.0 entwickelt. Damit wird das physikalisch-ingenieurtechnische Modell zur Zustandsbewertung der Brücke in den Mittelpunkt gestellt und der gesamte Lebenszyklus einer Brücke kann unabhängig von Datenformaten digital erfasst werden. Da der Aufbau der VWS durch die Granularität optimal strukturiert ist, bietet die Ablage und Einspeisung von Messdaten sowohl die Grundlage eines Live-Monitorings als auch den Grundstein für maschinelles Lernen (ML). Der Datenzugriff via S3-Schnittstelle erleichtert die Entwicklung von eigenen Prognosemodellen mit Informationsmustern (SHIP – Structural Health Information Pattern). Am Beispiel der Heinrichsbrücke Bamberg wird die praktische intelligente Umsetzung des Bauwerksmonitorings inkl. VWS mit Informationsmustern und ML gezeigt. N2 - On the way to the digital bridge, initial solutions already exist that can map the life cycle of a bridge. A wide variety of tools are available for planning, construction and maintenance, e. g. BIM, DIN 1076, SIB structures, monitoring etc., each of which works with different data formats. For an intelligent maintenance management, however, all data with the different data formats must be merged, stored, and managed in such a way that the mapping of a holistic digital twin of a structure is possible over the entire life cycle of a bridge. For this purpose, the authors have developed BBox, a prototype of an asset administration shell (AAS) based on Industry 4.0. This places the physical-engineering model for assessing the condition of the bridge at the center, and the entire life cycle of a bridge can be digitally recorded independently of data formats. Since the structure of the AAS is optimally structured through granularity, the storage and feeding of measurement data provides both the basis of live monitoring and the cornerstone for machine learning (ML). The data access via S3 interface facilitates the development of own prognosis models with information patterns (SHIP – Structural Health Information Pattern). Using the Heinrichsbrücke Bamberg as an example, the practical intelligent implementation of structural monitoring incl. AAS with information patterns and ML is shown. KW - Digitaler Zwilling KW - Lebenszyklus KW - Bauwerksmonitoring KW - Industrie 4.0 KW - Maschinelles Lernen KW - Digital twin KW - Life cycle KW - Structural health monitoring KW - Industry 4.0 KW - Machine learning PY - 2021 DO - https://doi.org/10.1002/bate.202100094 SN - 1437-0999 SP - 1 EP - 9 PB - Ernst & Sohn CY - Berlin AN - OPUS4-54017 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Küttenbaum, Stefan A1 - Braml, T. A1 - Taffe, A. A1 - Keßler, S. A1 - Maack, Stefan T1 - Reliability assessment of existing structures using results of nondestructive testing N2 - Making optimal decisions about the reliability of existing structures requires that the information used in assessment adequately represents the properties and the condition of the structures. The knowledge gap regarding a structure to be assessed can be successively filled by individually purposeful observations on site. This paper gives an overview of an approach for utilizing nondestructively gathered measurement results in reliability assessment of existing structures. An essential part of measurement-based stochastic modeling of basic variables is the calculation of measurement uncertainties, which serves to establish confidence in measurement, to ensure the comparability of unambiguously expressed measurement results, and to quantify the quality of the measured information. Regarding the current discourse on how to treat information collected on-site in the context of assessment, the authors recommend that measurement uncertainty becomes an uncertainty component mandatorily to be represented in measurement-based stochastic models. The main steps of the proposed concept are presented, and the advantages of its application are emphasized by means of a prestressed concrete bridge as case study. The bridge is assessed regarding the serviceability limit state decompression using ultrasonic and radar data measured at the structure. KW - Bridge KW - Measurement uncertainty KW - Prestressed concrete KW - Stochastic modeling KW - Probabilistic methods PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-529927 DO - https://doi.org/10.1002/suco.202100226 SN - 1751-7648 VL - 22 IS - 5 SP - 2895 EP - 2915 PB - John Wiley & Sons Ltd CY - Oxford AN - OPUS4-52992 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Küttenbaum, Stefan A1 - Maack, Stefan A1 - Braml, T. A1 - Taffe, A. A1 - Strübing, T. T1 - Bewertung von Bestandsbauwerken mit gemessenen Daten - Teil 2: Berechnung der Tragwerkszuverlässigkeit unter Einbeziehung der ZfP-Messergebnisse T1 - Reassessment of existing structures based on measured data - Part 2: Structural reliability analyses using NDT results N2 - Durch die Einbeziehung von gemessenen Daten bei der Bewertung von bestehenden Bauwerken können Unsicherheiten bei der Beurteilung des Tragverhaltens reduziert werden, ohne das normative Zuverlässigkeitsniveau einzuschränken. Informationen sind die wesentliche Grundlage für die Analyse der Zuverlässigkeit von Tragwerken. Umso wichtiger ist die Kenntnis über die Präzision und die Richtigkeit der verwendeten Informationen. Aus messtechnischer Sicht kann ein Messwert, dem keine Messunsicherheit beigeordnet wurde, als wertlos erachtet werden. Liegt ein vollständig dokumentiertes Messergebnis vor, so ist die Qualität der gemessenen Information bekannt und deren Vergleichbarkeit gewährleistet. In diesem Beitrag wird am Beispiel einer Spannbetonbrücke und zweier Grenzzustände gezeigt, wie Messergebnisse aus der zerstörungsfreien Prüfung in probabilistische Nachweise von Bestandsbauwerken einfließen können und welche Auswirkungen die Implementierung von gemessenen Daten bei der Bewertung von Bestandsbauwerken haben kann. N2 - Every decision about the reliability of a structure is associated with uncertainties. The reassessment of existing structures remains a major challenge. The decisive difference compared to the design of new structures is the possibility and necessity to collect individual information about the actual condition and properties of the structure. Such knowledge should be appreciated in the reassessment in order to reduce uncertainties and increase the validity of the results. Reliability analyses using measured data require the comparability of measurement results and the evaluation of the quality of the measured information. Both requirements can be met by adequate measurement uncertainty considerations. Besides, the destructive interventions necessary for the measurements should be kept to a minimum. This paper shows how non-destructively gathered measurement results can be incorporated into probabilistic reassessments and which effects the implementation of measured data can have when evaluating existing structures, using a prestressed concrete bridge as a case-study. KW - Nachrechnung KW - Zerstörungsfreie Prüfung KW - Zuverlässigkeitsanalyse KW - Messung KW - Spannbetonbrücke PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-519480 DO - https://doi.org/10.1002/best.202000087 SN - 0005-9900 SN - 1437-1006 VL - 116 IS - 3 SP - 183 EP - 199 PB - Ernst & Sohn CY - Berlin AN - OPUS4-51948 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Maack, Stefan A1 - Küttenbaum, Stefan A1 - Epple, Niklas A1 - Aligholizadeh, M. T1 - Die Ultraschall-Echomethode – von der Messung zur bautechnischen Kenngröße T1 - Ultrasonic Echo Method - Deriving structural parameters from measured values N2 - Zerstörungsfreie Prüfverfahren liefern wichtige Informationen zur Beurteilung von Bauwerken. Mit ihnen können Materialeigenschaften bestimmt oder die innere Struktur von Bauteilen beschrieben werden. Für letzteres werden in der Regel Volumenverfahren angewandt. Einen besonderen Stellenwert haben in der Praxis die Radar- und die Ultraschall-Echoverfahren. Ihre Anwendung erfordert lediglich eine einseitige Zugänglichkeit zum Bauteil. Zudem lassen sich zahlreiche unterschiedliche Prüfaufgaben lösen. Zum Stand der Technik gehören beispielsweise die Ortung von Bewehrung und Spannkanälen, die Bestimmung der Dicke von Bauteilen oder die Fehlerlokalisierung. In diesem Beitrag wird gezeigt, wie mithilfe von Ultraschall-Echomessungen gesammelte Messwerte in ein quantitatives Messergebnis überführt werden können, das wiederum in ingenieurtechnische Berechnungen einfließen kann. Einleitend werden die Prüfmethode und die Messtechnik erläutert. Anschließend wird das Vorgehen von der Auswertung der Messergebnisse bis zur Bestimmung der bautechnischen Kenngröße – Bauteildicke – gezeigt. Abschließend wird die Methodik an einem Referenzprüfkörper aus Polyamid demonstriert und den Ergebnissen von Messungen an Beton gegenübergestellt. KW - Zerstörungsfreie Prüfung KW - Ultraschall-Echoverfahren KW - Messunsicherheit KW - Bildgebende Darstellung KW - Schallgeschwindigkeit PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-521113 DO - https://doi.org/10.1002/best.202000091 VL - 116 IS - 3 SP - 200 EP - 211 PB - Ernst & Sohn AN - OPUS4-52111 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Küttenbaum, Stefan A1 - Taffe, A. A1 - Braml, T. A1 - Maack, Stefan ED - Alexander, M. G. ED - Beushausen, H. ED - Dehn, F. ED - Moyo, P. T1 - Reliability assessment of existing bridge constructions based on results of non-destructive testing N2 - The non-destructive testing methods available for civil engineering (NDT-CE) enable the measurements of quantitative parameters, which realistically describe the characteristics of existing buildings. In the past, methods for quality evaluation and concepts for validation expanded into NDT-CE to improve the objectivity of measured data. Thereby, a metrological foundation was developed to collect statistically sound and structurally relevant information about the inner construction of structures without destructive interventions. More recently, the demand for recalculations of structural safety was identified. This paper summarizes a basic research study on structural analyses of bridges in combination with NDT. The aim is to use measurement data of nondestructive testing methods as stochastic quantities in static calculations. Therefore, a methodical interface between the guide to the expression of uncertainty in measurement and probabilistic approximation procedures (e.g. FORM) has been proven to be suitable. The motivation is to relate the scientific approach of the structural analysis with real information coming from existing structures and not with those found in the literature. A case study about the probabilistic bending proof of a reinforced concrete bridge with statistically verified data from ultrasonic measurements shows that the measuring results fulfil the requirements concerning precision, trueness, objectivity and reliability. T2 - International Conference on Concrete Repair, Rehabilitation and Retrofitting (ICCRRR 2018) CY - Cape Town, South Africa DA - 19.11.2018 KW - NDT KW - Concrete KW - Probabilistic reassessment KW - Bridge PY - 2018 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-467898 DO - https://doi.org/10.1051/matecconf/201819906001 SN - 2261-236X VL - 199 SP - 06001, 1 EP - 9 PB - MATEC Web of Conferences AN - OPUS4-46789 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -