TY - JOUR A1 - Rus, J. A1 - Gustschin, A. A1 - Mooshofer, H. A1 - Grager, J.-C. A1 - Bente, Klaas A1 - Gaal, Mate A1 - Pfeiffer, F. A1 - Grosse, C. U. T1 - Qualitative comparison of non-destructive methods for inspection of carbon fiber-reinforced polymer laminates N2 - In the rapidly expanding composite industry, novel inspection methods have been developed in recent years. Particularly promising for air-coupled testing are cellular polypropylene transducers which offer better impedance matching to air than piezoelectric transducers. Furthermore, broadband transmitters (laser-induced ultrasound and thermoacoustic emitters) and receivers (optical microphones) have opened a completely new chapter for advanced contact-free ultra-sound inspection. X-ray dark-field radiography offers a different approach to detect porosity and microcracks, employing small angle X-ray scattering. These innovative ultrasonic and radiographic alternatives were evaluated in comparison with well-established inspection techniques. We applied thirteen different non-destructive methods to inspect the same specimen (a carbon fiber-reinforced polymer laminate with induced impact damage): air-coupled ultrasound testing (using piezoelectric transducers, broadband optical microphones, cellular polypropylene transducers, and a thermoa- coustic emitter), laser-induced ultrasound testing, ultrasonic immersion testing, phased array ultrasonic testing, optically excited lock-in thermography, and X-ray radiography (projectional absorption and dark-field, tomosynthesis, and micro-computed tomography). The inspection methods were qualitatively characterized by comparing the scan results. The conclusions are advantageous for a decision on the optimal method for certain testing constraints. KW - Carbon fiber-reinforced polymer KW - Air-coupled ultrasound KW - Optically excited lock-in thermography KW - X-ray micro-computed tomography KW - X-ray dark-field radiography PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-509473 DO - https://doi.org/10.1177/0021998320931162 SN - 0021-9983 VL - 54 IS - 27 SP - 4325 EP - 4337 PB - SAGE AN - OPUS4-50947 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Tiitta, M. A1 - Tiitta, V. A1 - Gaal, Mate A1 - Heikkinen, J. A1 - Lappalainen, R. A1 - Tomppo, L. T1 - Air-coupled ultrasound detection of natural defects in wood using ferroelectret and piezoelectric sensors N2 - Air-coupled ultrasound was used for assessing natural defects in wood boards by through-transmission scanning measurements. Gas matrix piezoelectric (GMP) and ferroelectret (FE) transducers were studied. The study also included tests with additional bias voltage with the ferroelectret receivers. Signal analyses, analyses of the measurement dynamics and statistical analyses of the signal parameters were conducted. After the measurement series, the samples were cut from the measurement regions and the defects were analyzed visually from the cross sections. The ultrasound responses were compared with the results of the visual examination of the cross sections. With the additional bias voltage, the ferroelectret measurement showed increased signal-to-noise ratio, which is especially important for air-coupled measurement of high-attenuation materials like wood. When comparing the defect response of GMP and FE sensors, it was found that FE sensors had more sensitive dynamic range, resulting from better s/n ratio and short response pulse. Classification test was made to test the possibility of detecting defects in sound wood. Machine learning methods including decision trees, k-nearest neighbor and support vector machine were used. The classification accuracy varied between 72 and 77% in the tests. All the tested machine learning methods could be used efficiently for the classification. KW - Air-coupled transducers KW - Wood KW - Ultrasound KW - Ultrasonic imaging KW - Ferroelectret KW - Machine learning PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-509503 DO - https://doi.org/10.1007/s00226-020-01189-y SP - 1 EP - 14 PB - Springer AN - OPUS4-50950 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Casperson, Ralf T1 - Datenformate für die zerstörungsfreie Prüfung N2 - Der Vortrag gibt eine Übersicht über die Versuche der Vergangenheit, ein standardisiertes Datenformat für die zerstörungsfreie Prüfung zu etablieren. T2 - 4. Sitzung DGZfP FA ZfP 4.0 UA Schnittstellen CY - Stockelsdorf, Germany DA - 19.02.2020 KW - ZfP KW - Datenformat KW - TRAPPIST KW - STEP KW - NDTML KW - DICONDE KW - HDF5 PY - 2020 AN - OPUS4-50448 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lauschkin, Maik A1 - Bulling, Jannis A1 - Lugovtsova, Yevgeniya A1 - Wasmer, P. A1 - Prager, Jens T1 - Bestimmung von Materialparametern aus dem dispersiven Verhalten geführter Wellen mittels neuronaler Netze N2 - Damit eine Simulationsrechnung, beispielsweise mit einer FEM-Software, eine ausreichend hohe Genauigkeit erreicht, muss vorausgesetzt werden, dass die Modellparameter eine sehr hohe Güte aufweisen. Die genaue Kenntnis der Materialparameter ist dabei von besonderer Bedeutung. Um diese Parameter bestimmen zu können, müssen die verwendeten Werkstoffe messtechnisch charakterisiert werden. Neben anderen Ansätzen sind dafür akustische Verfahren im Ultraschallbereich geeignet. Für dünnwandige und plattenförmige Materialien können aus den sich ausbreitenden geführten Wellen messtechnisch Dispersionskurven bestimmt und aus diesen die Materialparameter abgeleitet werden. Da für die Signalverarbeitung und für Optimierungsaufgaben aktuell zunehmend Machine Learning Tools zum Einsatz kommen, stellt sich die Frage, ob diese Werkzeuge auch für die Ermittlung der Materialparameter aus den gemessenen Dispersionskurven eingesetzt werden können. In der vorgestellten Untersuchung soll ein Convolutional Neural Network aufgestellt werden, welches aus Dispersionsbildern Muster extrahiert und aus diesen eine Schätzung für die Materialparameter ermittelt. Um die Machbarkeit dieses Ansatzes zu prüfen, werden zunächst nur isotrope Materialien betrachtet. Für das Netz werden mit der Scaled-Boundary-Finite-Element-Methode synthetische Daten für das Trainieren und Validieren generiert. Zusätzlich werden die Hyperparameter des neuronalen Netzes variiert, um ein optimales Model für die Schätzung zu finden. Anschließend kann das Netz mit experimentellen Daten getestet und das Ergebnis hinsichtlich der Genauigkeit bewertet werden. T2 - DAGA 2020 - 46. Jahrestagung für Akustik CY - Meeting was canceled DA - 16.03.2020 KW - Machinelles Lernen KW - Geführte Ultraschallwellen KW - Materialcharakterisierung KW - Elastische Konstanten KW - Isotrope Materialien PY - 2020 SN - 978-3-939296-17-1 SP - 571 EP - 574 PB - Deutsche Gesellschaft für Akustik e.V. CY - Berlin AN - OPUS4-50765 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Pohl, Rainer A1 - Casperson, Ralf A1 - Ehlers, Henrik A1 - Pelkner, Matthias T1 - Elektromagnetische zerstörungsfreie Prüfverfahren N2 - Übersicht über die die im FB 8.4 bearbeiteten elektromagnetischen Prüfverfahren mit den Schwerpunkten bildgebende Wirbelstromprüfung, sensorbasierte Streuflussprüfung, magnetische Materialcharakterisierung und Sondenentwicklung. KW - Wirbelstromprüfung KW - Wirbelstromsenoren KW - GMR-Sensoren KW - Magnetische Materialcharakterisierung PY - 2020 SP - 1 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-51033 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gaal, Mate T1 - Luftultraschall N2 - Dieser Vortrag bietet eine Einführung zur luftgekoppelten Ultraschallprüfung. Es werden die theoretischen Grundlagen erläutert und Beispiele für Anwendungen in der Praxis gegeben. T2 - Schulung Ultraschallprüfung Stufe 3 CY - Berlin, Germany DA - 28.09.2020 KW - Luftgekoppelte Ultraschallprüfung KW - Luftankopplung KW - Ultraschallwandler PY - 2020 AN - OPUS4-51578 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lugovtsova, Yevgeniya T1 - Characterization of a Flexible Piezopolymer-based Interdigital Transducer for Selective Excitation of Ultrasonic Guided Waves N2 - Structural health monitoring (SHM) is a term that groups together techniques adopted to evaluate in a continued fashion the structural integrity and degradation of technical appliances. SHM is particularly attractive for components that are difficult to access or expensive to take off-line. Among many other techniques, SHM can be performed using ultrasonic guided waves (UGW) which have an advantage of traveling over Long distances. Various guided wave modes exist along with many methods for their generation and sensing, e.g by means of interdigital transducers (IDT). This contribution is dedicated to the design and characterization of a flexible piezopolymerbased IDT which allows for the selective excitation of UGW, resulting in more straightforward data analysis. The designed IDT was characterized using a 3D Laser Doppler Vibrometer (3D LDV) in the air to identify and analyze the IDT’s Vibration modes. Then the transducer was mounted on an aluminum plate, and the generated wavefield was measured with the 3D LDV. According to this investigation, we demonstrate that it is possible to selectively excite desired guided wave mode, namely the A0 mode, suppressing the excitation of the S0 mode. Moreover, the measured wavefield allows for analysis of the directivity of the designed IDT. All in all the results show good correlation between theoretical predictions and measured values, thus allowing to use the current design in terms of selective excitation as it is. T2 - IEEE International Ultrasonics Symposium CY - Online meeting DA - 06.09.2020 KW - Lamb waves KW - Non-Destructive Testing KW - Structural Health Monitoring KW - Polyvinylidene Fluoride (PVDF) PY - 2020 AN - OPUS4-51202 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lugovtsova, Yevgeniya A1 - Bulletti, A. A1 - Giannelli, P. A1 - Capineri, L. A1 - Prager, Jens T1 - Characterization of a Flexible Piezopolymer-based Interdigital Transducer for Selective Excitation of Ultrasonic Guided Waves N2 - Structural health monitoring (SHM) is a term that groups together techniques adopted to evaluate in a continued fashion the structural integrity and degradation of technical appliances. SHM is particularly attractive for components that are difficult to access or expensive to take off-line. Among many other techniques, SHM can be performed using ultrasonic guided waves (UGW) which have an advantage of traveling over Long distances. Various guided wave modes exist along with many methods for their generation and sensing, e.g by means of interdigital transducers (IDT). This contribution is dedicated to the design and characterization of a flexible piezopolymerbased IDT which allows for the selective excitation of UGW, resulting in more straightforward data analysis. The designed IDT was characterized using a 3D Laser Doppler Vibrometer (3D LDV) in the air to identify and analyze the IDT’s Vibration modes. Then the transducer was mounted on an aluminum plate, and the generated wavefield was measured with the 3D LDV. According to this investigation, we demonstrate that it is possible to selectively excite desired guided wave mode, namely the A0 mode, suppressing the excitation of the S0 mode. Moreover, the measured wavefield allows for analysis of the directivity of the designed IDT. All in all the results show good correlation between theoretical predictions and measured values, thus allowing to use the current design in terms of selective excitation as it is. T2 - I2020 IEEE International Ultrasonics Symposium (IUS) CY - Online meeting DA - 07.09.2020 KW - Lamb waves KW - Non-Destructive Testing KW - Structural Health Monitoring KW - Polyvinylidene Fluoride (PVDF) PY - 2020 SN - 978-1-7281-5448-0 SP - 1261, 45 AN - OPUS4-51441 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pelkner, Matthias T1 - Non-Destructive Testing - Electromagnetic Methods N2 - This presentation contains a short summary about the basics of eddy current testing and magnetic flux leakage testing. In addition, the main focus of the talk lies on the application of point-like sensors like GMR for NDT. T2 - 1st Training Event - ITN project GW4SHM CY - Online meeting DA - 23.11.2020 KW - GMR KW - Magnetic flux leakage testing KW - Eddy current testing PY - 2020 AN - OPUS4-51889 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pelkner, Matthias T1 - Wirbelstromprüfung von Komposit-Druckbehältern N2 - Komposit-Druckgefäße für den Gefahrguttransport sowie für Wasserstoff-und Erdgasfahrzeuge bestehen aus einem lasttragenden Komposit und einer gasdichten, metallischen oder polymeren Barriereschicht (Liner). Zur Untersuchung der Integrität der Druckflaschen wurde die Wirbelstromprüfung eingesetzt. Hierbei wurden verschiedene Frequenzbereiche angewendet, um so die unterschiedlichen Materialien untersuchen zu können. Ziel der Untersuchungen war es, alterungsbedingte Schädigungen rechtzeitig zu detektieren. Der Vortrag stellt diese Ergebnisse vor. T2 - Carbon United - Gemeinsame Sitzung 3er-AG Zerstörungsfreie Werkstoff- u. Bauteilprüfung, Verbindungstechnik, Engineering CY - Online meeting DA - 07.12.2020 KW - Wirbelstromprüfung KW - CFK KW - Druckbehälter PY - 2020 AN - OPUS4-51892 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Reichel, V. E. A1 - Matuszak, J. A1 - Bente, Klaas A1 - Heil, T. A1 - Kraupner, A. A1 - Dutz, S. A1 - Cicha, I. A1 - Faivre, D. T1 - Magnetite-Arginine Nanoparticles as a Multifunctional Biomedical Tool N2 - Iron oxide nanoparticles are a promising platform for biomedical applications, both in terms of diagnostics and therapeutics. In addition, arginine-rich polypeptides are known to penetrate across cell membranes. Here, we thus introduce a system based on magnetite nanoparticles and the polypeptide poly-l-arginine (polyR-Fe3O4). We show that the hybrid nanoparticles exhibit a low cytotoxicity that is comparable to Resovist®, a commercially available drug. PolyR-Fe3O4 particles perform very well in diagnostic applications, such as magnetic particle imaging (1.7 and 1.35 higher signal respectively for the 3rd and 11th harmonic when compared to Resovist®), or as contrast agents for magnetic resonance imaging (R2/R1 ratio of 17 as compared to 11 at 0.94 T for Resovist®). Moreover, these novel particles can also be used for therapeutic purposes such as hyperthermia, achieving a specific heating power ratio of 208 W/g as compared to 83 W/g for Feridex®, another commercially available product. Therefore, we envision such materials to play a role in the future theranostic applications, where the arginine ability to deliver cargo into the cell can be coupled to the magnetite imaging properties and cancer fighting activity. KW - Iron oxide KW - Nanoparticle KW - Theranostics KW - MRI KW - Hyperthermia PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-515993 DO - https://doi.org/10.3390/nano10102014 VL - 10 IS - 10 SP - 2014 PB - MDPI AN - OPUS4-51599 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bulling, Jannis T1 - Numerical methods (part II) Finite element method (FEM), Spectral element method (SEM) and Scaled Boundary FEM (SBFEM) N2 - A general presentation on numerical methods. In particular, the Finite Element Method, the Spectral Element Method, and the Scaled Boundary Finite Element Method. T2 - ITN-Trainingsevent CY - Online meeting DA - 22.11.2020 KW - FEM KW - SBFEM KW - SEM PY - 2020 AN - OPUS4-52271 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Vössing, Konrad A1 - Gaal, Mate A1 - Niederleithinger, Ernst T1 - Imaging wood defects using air coupled ferroelectret ultrasonic transducers in reflection mode N2 - Air-coupled ultrasound (ACU) is used to detect defects in wood panels without physically contacting the sample and with a quick scanning rate. Transducers made of cellular polypropylene (PP) with a high signal-to-noise ratio are quite suitable for ACU testing of wood. The extremely low modulus of elasticity and low density of PP transducers results in a small difference in acoustic impedance for the Transmission of ultrasonic waves between the transducer and air, allowing new areas of application to become possible. To demonstrate the suitability of the reflection technique, measurements are shown on the three samples Multiplex, LVL, and MDF and compared with transmission measurements. Due to this acoustic barrier and the use of cellular PP transducers, an exact detection of delamination and cavities is possible in wood panels up to 40 mm thick. If only one side of an object is accessible and the depth of the defect is of interest, the reflection technique is preferred at the expense of a reduced measuring accuracy and Penetration depth. KW - Wood KW - Ultrasound KW - Air coupled KW - Defects PY - 2020 DO - https://doi.org/10.1016/j.conbuildmat.2020.118032 VL - 241 SP - 118032, 1 EP - 8 PB - Elsevier Ltd. AN - OPUS4-50235 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bulling, Jannis T1 - Ein inverses Verfahren zur Schadensrekonstruktion mittels geführter Wellen N2 - Eine zentrale Aufgabe der zerstörungsfreien Prüfung und der Strukturüberwachung (engl. Structural Health Monitoring - SHM) mit Ultraschallwellen ist die Bewertung von Schäden in Bauteilen. In vielen Bauteilen, wie zum Beispiel platten- und schalenförmigen Strukturen, Rohrleitungen oder Laminaten, breitet sich der Ultraschall in Form geführter Wellen aus. Zwar haben geführte Wellen eine relativ große Reichweite innerhalb des Bauteils und ermöglichen so eine großflächige Prüfung, ihre multimodalen und dispersiven Eigenschaften erschweren jedoch die Analyse der vom Schaden kommenden Reflexionen. Eine Möglichkeit, die Messsignale zu interpretieren und die Schäden zu charakterisieren, ist deren Vergleich mit der Wellenausbreitung in einem digitalen Modell. Hierbei stellt sich die Aufgabe, den Schaden im digitalen Modell anhand der Messdaten zu rekonstruieren. Diese Rekonstruktion beschreibt ein inverses Problem, das mehrere Vorwärtsrechnungen braucht, um das Schadensmodell an die Messdaten anzupassen.Durch die kleine Wellenlänge von Ultraschallwellen sind klassische Vorwärtsmethoden wie die Finte Elemente Methode rechenintensiv, weshalb die Autoren die semi-analytische Scaled Boundary Finite Element Method (SBFEM) benutzen, um den Rechenaufwand zu verringern. Im Beitrag wird ein inverses Verfahren basierend auf dem Automatischen Differenzieren in Kombination mit der SBFEM vorgestellt und an verschiedenen Schadenstypen in 2D-Querschnittmodellen von Wellenleitern getestet. In der präsentierten Vorstudie werden dafür „Messdaten“ aus unabhängigen Simulationen verwendet. T2 - DAGA 2021 - 47. Jahrestagung für Akustik CY - Vienna, Austria DA - 15.08.2021 KW - SBFEM KW - Inverse Verfahren KW - AD KW - SHM KW - NDT PY - 2021 AN - OPUS4-53304 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bulling, Jannis A1 - Jurgelucks, B. A1 - Prager, Jens A1 - Walther, A. T1 - Ein inverses Verfahren zur Schadensrekonstruktion mittels geführter Wellen N2 - Eine zentrale Aufgabe der zerstörungsfreien Prüfung und der Strukturüberwachung (engl. Structural Health Monitoring - SHM) mit Ultraschallwellen ist die Bewertung von Schäden in Bauteilen. In vielen Bauteilen, wie zum Beispiel platten- und schalenförmigen Strukturen, Rohrleitungen oder Laminaten, breitet sich der Ultraschall in Form geführter Wellen aus. Zwar haben geführte Wellen eine relativ große Reichweite innerhalb des Bauteils und ermöglichen so eine großflächige Prüfung, ihre multimodalen und dispersiven Eigenschaften erschweren jedoch die Analyse der vom Schaden kommenden Reflexionen. Eine Möglichkeit, die Messsignale zu interpretieren und die Schäden zu charakterisieren, ist deren Vergleich mit der Wellenausbreitung in einem digitalen Modell. Hierbei stellt sich die Aufgabe, den Schaden im digitalen Modell anhand der Messdaten zu rekonstruieren. Diese Rekonstruktion beschreibt ein inverses Problem, das mehrere Vorwärtsrechnungen braucht, um das Schadensmodell an die Messdaten anzupassen. Durch die kleine Wellenlänge von Ultraschallwellen sind klassische Vorwärtsmethoden wie die Finte Elemente Methode rechenintensiv, weshalb die Autoren die semi-analytische Scaled Boundary Finite Element Method (SBFEM) benutzen, um den Rechenaufwand zu verringern. Im Beitrag wird ein inverses Verfahren basierend auf dem Automatischen Differenzieren in Kombination mit der SBFEM vorgestellt und an verschiedenen Schadenstypen in 2D-Querschnittmodellen von Wellenleitern getestet. In der präsentierten Vorstudie werden dafür „Messdaten“ aus unabhängigen Simulationen verwendet. T2 - DAGA 2021 - 47. Jahrestagung für Akustik CY - Vienna, Austria DA - 15.08.2021 KW - SBFEM KW - Inverse Probleme KW - SHM KW - NDT KW - AD PY - 2021 SP - 1 EP - 4 PB - Deutsche Gesellschaft für Akustik (DEGA) CY - Berlin AN - OPUS4-53305 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Held, Mathias A1 - Rashwan, Abdalla A1 - Bulling, Jannis A1 - Lugovtsova, Yevgeniya A1 - Lauschkin, Maik A1 - Prager, Jens T1 - Inverse Bestimmung elastischer Materialparameter aus dem Ausbreitungsverhalten geführter Ultraschallwellen mittels eines Convolutional Neuronal Networks N2 - Detailliertes Wissen über die mechanischen Eigenschaften verwendeter Materialien ist Grundvoraussetzung für viele ingenieurtechnische Aufgaben und Dienstleistungen. Zur Bestimmung der elastischen Materialparameter gibt es verschiedene klassische, zerstörende Prüfverfahren. Eine Möglichkeit der zerstörungsfreien Bestimmung liegt in der Auswertung von Messergebnissen, die auf Basis des Ausbreitungsverhaltens geführter Ultraschallwellen gewonnen wurden. Das Ausbreitungsverhalten geführter Ultraschallwellen kann mittels Dispersionsabbildungen dargestellt werden. Um aus messtechnisch ermittelten Dispersionsabbildungen Rückschlüsse auf die Materialparameter zu ziehen, werden in der aktuellen Forschung verschiedene inverse Methoden diskutiert. Maschinelles Lernen und insbesondere Convolutional Neural Networks (CNNs) stellen eine Möglichkeit der automatisierten inversen Modellierung und Evaluierung von Bilddaten dar. In diesem Beitrag wird gezeigt, wie das Ausbreitungsverhalten von geführten Ultraschallwellen unter Verwendung von CNNs genutzt werden kann, um die isotropen elastischen Konstanten einer plattenförmigen Struktur zu bestimmen. Hierfür werden die verwendeten Daten analysiert, das Preprocessing erläutert und eine grundlegende CNN-Architektur gewählt. Zur Auswertung des generierten Modells werden verschiedene Verfahren wie Gradienten-Mapping und die Visualisierung der verschiedenen Schichten vorgestellt. Die Anwendbarkeit der Methode wird anhand synthetischer Daten demonstriert. T2 - DAGA 2021 CY - Vienna, Austria DA - 15.08.2021 KW - Geführte Ultraschallwellen KW - Inverse Probleme KW - Materialcharakterisierung KW - Maschinelles Lernen KW - Dispersion KW - Lamb Wellen PY - 2021 SN - 978-3-939296-18-8 VL - 47 SP - 659 EP - 662 AN - OPUS4-53492 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zeipert, H. A1 - Johannesmann, S. A1 - Nicolai, Marcel A1 - Lugovtsova, Yevgeniya A1 - Prager, Jens A1 - Henning, B. T1 - Quantifying the coupling strength of adhesively bonded materials by investigating mode repulsion regions N2 - In the field of non-destructive testing, Lamb waves are often used for material characterisation. The increasing computational capabilities further enable complex and detailed simulations to predict the material behaviour in reality. Since adhesive bonding of different materials is a widely used method in modern applications, a reliable measurement system to determine the quality of these adhesive bonds is needed. Investigations of the dispersive behaviour of acoustic waves in adhesively bonded multi-layered waveguides show mode repulsions in the dispersion diagrams in regions where the modes of the single materials would otherwise intersect. In previous works, changes of the distance between those modes with respect to the bonding quality are observed. The experimental data for this investigation is generated using pulsed laser radiation to excite broadband acoustic waves in plate like specimens which are detected by a piezoelectric ultrasonic transducer. Numerical data is generated using simulations via a semi-analytical finite element method. Using a combination of experimental and numerical data, the present work introduces an approach to determine a parameter which indicates the bonding quality in relation to an ideal material coupling. T2 - DAGA 2021 CY - Vienna, Austria DA - 15.08.2021 KW - Ultrasonic guided waves KW - Multi-layered structures KW - Laser excited ultrasonic waves PY - 2021 SP - 1532 EP - 1535 AN - OPUS4-53581 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lugovtsova, Yevgeniya A1 - Bulling, Jannis A1 - Mesnil, O. A1 - Prager, Jens A1 - Gohlke, Dirk A1 - Boller, C. T1 - Damage quantification in an aluminium-CFRP composite structure using guided wave wavenumber mapping: Comparison of instantaneous and local wavenumber analyses N2 - Composite-overwrapped pressure vessels (COPV) are increasingly used in the transportation industry due to their high strength to mass ratio. Throughout the years, various designs were developed and found their applications. Currently, there are five designs, which can be subdivided into two main categories - with a load-sharing metal liner and with a non-load-sharing plastic liner. The main damage mechanism defining the lifetime of the first type is fatigue of the metal liner, whereas for the second type it is fatigue of the composite overwrap. Nevertheless, one damage type which may drastically reduce the lifetime of COPV is impact-induced damage. Therefore, this barely visible damage needs to be assessed in a non-destructive way to decide whether the pressure vessel can be further used or has to be put out of service. One of the possible methods is based on ultrasonic waves. In this contribution, both conventional ultrasonic testing (UT) by high-frequency bulk waves and wavenumber mapping by low frequency guided waves are used to evaluate impact damage. Wavenumber mapping techniques are first benchmarked on a simulated aluminium panel then applied to experimental measurements acquired on a delaminated aluminium-CFRP composite plate which corresponds to a structure of COPV with a load-sharing metal liner. The analysis of experimental data obtained from measurements of guided waves propagating in an aluminium-CFRP composite plate with impact-induced damage is performed. All approaches show similar performance in terms of quantification of damage size and depths while being applied to numerical data. The approaches used on the experimental data deliver an accurate estimate of the in-plane size of the large delamination at the aluminium-CFRP interface but only a rough estimate of its depth. Moreover, none of the wavenumber mapping techniques used in the study can quantify every delamination between CFRP plies caused by the impact, which is the case for conventional UT. This may be solved by using higher frequencies (shorter wavelengths) or more advanced signal processing techniques. All in all, it can be concluded that imaging of complex impact damage in fibre-reinforced composites based on wavenumber mapping is not straightforward and stays a challenging task. KW - Ultrasonic guided waves KW - Instantaneous wavenumber analysis KW - Local wavenumber analysis KW - Signal processing PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-528203 DO - https://doi.org/10.1016/j.ndteint.2021.102472 SN - 0963-8695 VL - 122 SP - 2472 PB - Elsevier Ltd. CY - Amsterdam, Netherlands AN - OPUS4-52820 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Tschöke, K. A1 - Müller, I. A1 - Memmolo, V. A1 - Moix-Bonet, M. A1 - Moll, J. A1 - Lugovtsova, Yevgeniya A1 - Golub, M. A1 - Sridaran Venkat, R. A1 - Schubert, L. T1 - Feasibility of Model-Assisted Probability of Detection Principles for Structural Health Monitoring Systems based on Guided Waves for Fibre-Reinforced Composites N2 - In many industrial sectors, Structural Health Monitoring (SHM) is considered as an addition to Non-Destructive Testing (NDT) that can reduce maintenance effort during lifetime of a technical facility, structural component or vehicle. A large number of SHM methods is based on ultrasonic waves, whose properties change depending on structural health. However, the wide application of SHM systems is limited due to the lack of suitable methods to assess their reliability. The evaluation of the system performance usually refers to the determination of the Probability of Detection (POD) of a test procedure. Up to now, only few limited methods exist to evaluate the POD of SHM systems, which prevent them from being standardised and widely accepted in industry. The biggest hurdle concerning the POD calculation is the large amount of samples needed. A POD analysis requires data from numerous identical structures with integrated SHM systems. Each structure is then damaged at different locations and with various degrees of severity. All of this is connected to high costs. Therefore, one possible way to tackle this problem is to perform computer-aided investigations. In this work, the POD assessment procedure established in NDT according to the Berens model is adapted to guided wave-based SHM systems. The approach implemented here is based on solely computer-aided investigations. After efficient modelling of wave propagation phenomena across an automotive component made of a carbon fibre-reinforced composite, the POD curves are extracted. Finally, the novel concept of a POD map is introduced to look into the effect of damage position on system reliability. KW - Reliability KW - Acoustics KW - Monitoring KW - Automotive engineering KW - Elastodynamic Finite Inegration Technique PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-528218 DO - https://doi.org/10.1109/TUFFC.2021.3084898 VL - 68 IS - 10 SP - 3156 EP - 3173 AN - OPUS4-52821 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Casperson, Ralf T1 - Non-Destructive Testing of Composite Pressure Vessels using Conventional and High-Frequency Eddy Current Technique N2 - Pressure vessels for the transport of hazardous gases are subjected to a hydraulic internal pressure test. Basis for the design of metallic pressure vessels is the fatigue strength according to Wöhler, whereby the number of load changes can be equated with the number of filling / emptying cycles of the pressure vessel. Metallic pressure vessels are increasingly replaced by composite pressure vessels due to the weight savings. However, at composite preasure vessels it is not possible to conclude from the number of load cycles on the fatigue strength, because composite pressure vessels are ageing even at constant internal pressure. Non-destructive conventional and high frequency eddy current testing of the metallic liner and load bearing CFRP layer are presented as an alternative to hydraulic internal pressure test. T2 - TAHYA Workshop CY - Online meeting DA - 02.06.2021 KW - Non-destructive testing KW - Composite preasure vessel KW - Eddy currnet testing PY - 2021 AN - OPUS4-52856 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bulling, Jannis T1 - A Combination of the Scaled Boundary Finite Element Method with the Mortar Method N2 - The simulation of ultrasonic waves in a linearly elastic body can be computationally intensive. The reason is the relatively short wavelength compared to the body size for high frequencies. One possible approach to counteract the high computational costs is to decompose the domain into small parts and strive for parallelization. The Mortar Method is a well-established approach for domain decomposition. A rather new approach to discretize the emerging subdomains is the Scaled Boundary Finite Element Method. This semi-analytical method has many attractive properties. Some of these properties are listed subsequently. The grid consists of polygonal elements, which leaves much freedom in the meshing process. A variety of material distributions, including anisotropic materials, can be considered. High-order shape functions can be used for optimal convergence properties. The approach treats singularities at crack tips and corners analytically. Especially in the frequency domain, the Scaled Boundary Finite Element Method reduces the dimension of the approximation because only degrees of freedom which are associated with the boundary of a polygonal element are necessary. Those desirable properties make the method particularly suitable for calculating the dynamic responses in bodies with cracks, as it is essential for many non-destructive testing and structural health monitoring applications. In this contribution, we present a combination of the Scaled Boundary Finite Element Method with the Mortar Method in two dimensions. The presentation starts with a theoretical overview of both approaches. Subsequently, numerical examples demonstrate the stability of the combination for the polygonal boundary of the elements. The numerical examples increase in complexity and are compared to results computed on non-divided domains with the Finite Element Method. T2 - WCCM-ECCOMAS CONGRESS CY - Online meeting DA - 11.01.2021 KW - Ultrasound KW - Numerical Simulation KW - Scaled Boundary Finite Element Method, Mortar Method PY - 2021 AN - OPUS4-52275 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Held, Mathias A1 - Rashwan, Abdalla A1 - Lauschkin, Maik A1 - Bulling, Jannis A1 - Lugovtsova, Yevgeniya A1 - Prager, Jens T1 - Inverse determination of elastic material parameters from ultrasonic guided waves dispersion measurements using Convolutional Neuronal Networks N2 - In the context of Industry 4.0 and especially in the field of Structural Health Monitoring, Condition Monitoring and Digital Twins, simulations are becoming more and more important. The exact determination of material parameters is required for realistic results of numerical simulations of the static and dynamic behavior of technical structures. There are many possibilities to determine elastic material parameters. One possibility of non-destructive testing are ultrasonic guided waves. For the evaluation of the measurement results, mostly inverse methods are applied in order to be able to draw conclusions about the elastic material parameters from analysing the ultrasonic guided wave propagation. For the inverse determination of the elastic material Parameters with ultrasonic guided waves, several investigations were carried out, e.g. the determination of the isotropic material parameters through the point of zero-groupvelocity or anisotropic material parameters with a simplex algorithm. These investigations are based on the evaluation of dispersion images. Machine learning and in particular Convolutional Neural Networks (CNN) are one possibility of the automated evaluation from Image data, e.g. classification or object recognition problems. This article shows how the dispersive behavior of ultrasonic guided waves and CNNs can be used to determine the isotropic elastic constants of plate-like structures. T2 - SMSI 2021 2021-05-03 - 2021-05-06 digital CY - Online meeting DA - 03.05.2021 KW - Convolutional Neuronal Networks KW - Inverse Probleme KW - Materialcharakterisierung KW - guided waves KW - Dispersion PY - 2021 SN - 978-3-9819376-4-0 DO - https://doi.org/10.5162/SMSI2021/A10.2 VL - 2021 SP - 239 EP - 240 AN - OPUS4-52618 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gaal, Mate T1 - Charakterisierung von luftgekoppelten Ultraschallwandlern N2 - Mit dem steigenden Einsatz der luftgekoppelten Ultraschallprüfung steigt auch der Bedarf an verlässlichen Methoden der Charakterisierung der eingesetzten Technik. Mehrere unterschiedliche Verfahren zur Charakterisierung von luftgekoppelten Wandlern und der entsprechenden Gerätetechnik werden verwendet. Prüfkopf-Datenblätter verschiedener Hersteller beinhalten unterschiedliche Prüfkopfparameter, wobei oft eigene Verfahren für die Charakterisierung dieser Prüfköpfe verwendet werden. Diese Vielfalt der Parameter und Verfahren erschwert den potenziellen Kunden den Vergleich zwischen den Prüfköpfen unterschiedlicher Hersteller. Daraus ergibt sich der Bedarf, die Verfahren zur Charakterisierung von luftgekoppelten Ultraschallwandlern zu standardisieren. Vorrangig diese Überlegungen bewegten Hersteller von luftgekoppelten Ultraschallwandlern, Forschungseinrichtungen und Anwender sich zu vernetzen und im Rahmen des Fachausschusses „Ultraschall“ den Unterausschuss „Luftgekoppelte Ultraschallprüfung“ zu gründen. Als erstes Ziel hat sich der Unterausschuss die Erarbeitung einer Richtlinie zur Charakterisierung von luftgekoppelten Ultraschallwandlern gesetzt. Dieser Beitrag ist ein Überblick über viele Methoden zur Charakterisierung von luftgekoppelten Ultraschallwandlern, mit dem Schwerpunkt auf der akustischen Charakterisierung. Zu den wichtigsten Wandlerparametern gehören Empfindlichkeit, Mittenfrequenz, Bandbreite, Fokusgröße und Fokusabstand. Verschiedene Methoden der Schallfeldvermessung werden untereinander verglichen. Diese Überlegungen bieten den Ausgangspunkt für spätere Arbeit an einer Richtlinie zur Charakterisierung von luftgekoppelten Ultraschallwandlern. T2 - DGZfP-Jahrestagung 2021 CY - Online meeting DA - 10.05.2021 KW - Luftgekoppelte Ultraschallprüfung KW - Richtlinie KW - Ultraschallwandler KW - Charakterisierung PY - 2021 AN - OPUS4-52642 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gautzsch, T. T1 - Luftgekoppelte Ultraschallprüfung, eine Alternative in der zerstörungsfreien Prüfung N2 - Die luftgekoppelte Ultraschallprüfung (ACUT) ist ein vielfach bewährtes zerstörungsfreies Prüfverfahren, welches von vielen Anwendern jedoch nur am Rande oder gar nicht wahrgenommen wird. Insbesondere, die nach wie vor in der Ultraschallausbildung gelehrten Theorien zur wellenlängenabhängigen minimalen detektierbaren Fehlergröße und die vermeintliche Notwendigkeit der Verwendung von Koppelmittel schrecken viele potentielle Anwender davon ab für ihr Prüfproblem ACUT in Betracht zu ziehen. Des Weiteren wird ACUT häufig nicht als eigenständiges Prüfverfahren erkannt, sodass versucht wird, flüssigkeitsgekoppelte Ultraschallprüfungen ohne Beachtung der Besonderheiten zu ersetzen. T2 - DGZfP-Jahrestagung 2021 CY - Online meeting DA - 10.05.2021 KW - Luftgekoppelte Ultraschallprüfung PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-526431 UR - https://jahrestagung.dgzfp.de/Programm#P53 AN - OPUS4-52643 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Held, Mathias T1 - Inverse determination of elastic material parameters from ultrasonic guided waves dispersion measurements using Convolutional Neuronal Networks N2 - This presentation shows how the dispersive behavior of ultrasonic guided waves in isotropic materials can be used by means of Convolutional Neural Networks to determine the elastic parameters. For this purpose, the preprocessing, the training, the chosen architecture and the results are evaluated on the basis synthetic image data. This presentation was given at the SMSI 2021. T2 - SMSI 2021 2021-05-03 - 2021-05-06 digital CY - Online Meeting DA - 03.05.2021 KW - Guided waves KW - Inverse Probleme KW - Materialcharakterisierung KW - Convolutional Neuronal Networks KW - Dispersion PY - 2021 AN - OPUS4-52625 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zeipert, H. A1 - Claes, L. A1 - Johannesmann, S. A1 - Webersen, M. A1 - Lugovtsova, Yevgeniya A1 - Prager, Jens A1 - Henning, B. T1 - Measurement and simulation of Lamb waves in adhesive-bonded multilayer systems N2 - Lamb waves are a common tool in the field of non-destructive testing and are widely used for materialcharacterisation. Further, the increasing computational capability of modern systems enables the Simulation of complex and detailed material models. This work demonstrates the possibility of simulating an adhesive-bonded multilayer system by characterising each layer individually, and introduces an Approach for determining the dispersive behaviour of acoustic waves in a multilayer system via real measurements. T2 - SMSI 2021 Conference – Sensor and Measurement Science International CY - Online meeting DA - 03.05.2021 KW - Adhesive bonds KW - Lamb waves KW - Elastic constants KW - Non-Destructive Testing KW - Ultrasound PY - 2021 DO - https://doi.org/10.5162/SMSI2021/A8.2 SP - 91 EP - 92 AN - OPUS4-52634 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zeipert, H. T1 - Measurement and simulation of Lamb waves in adhesive-bonded multilayer systems N2 - Lamb waves are a common tool in the field of non-destructive testing and are widely used for material characterisation. Further, the increasing computational capability of modern systems enables the Simulation of complex and detailed material models. This work demonstrates the possibility of simulating an adhesive-bonded multilayer system by characterising each layer individually, and introduces an Approach for determining the dispersive behaviour of acoustic waves in a multilayer system via real measurements. T2 - SMSI 2021 Conference – Sensor and Measurement Science International CY - Online meeting DA - 03.05.2021 KW - Adhesive bonds KW - Lamb waves KW - Elastic constants KW - Non-Destructive Testing KW - Ultrasound PY - 2021 AN - OPUS4-52635 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Essig, W. A1 - Bernhardt, Y. A1 - Döring, D. A1 - Solodov, I. A1 - Gautzsch, T. A1 - Gaal, Mate A1 - Hufschläger, Daniel A1 - Sommerhuber, R. A1 - Marhenke, T. A1 - Hasener, J. A1 - Szewieczek, A. A1 - Hillger, W. T1 - Air-coupled ultrasound - emerging NDT method N2 - This paper deals with the state of the art of air-coupled ultrasonic testing. KW - Air-coupled KW - Ultrasonic testing KW - Transducers PY - 2021 SN - 1616-069X VL - 173 SP - 32 EP - 43 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) CY - Berlin AN - OPUS4-52231 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schnur, C. T1 - Explainable machine learning for damage detection - In carbon fiber composite plates under varying temperature conditions N2 - Understanding on how a machine learning model interprets data is a crucial step to verify its reliability and avoid overfitting. While the focus of the scientific community is nowadays orientated towards deep learning approaches, which are considered as black box approaches, this work presents a toolbox that is based on complementary methods of feature extraction and selection, where the classification decisions of the model are transparent and can be physically interpreted. On the example of guided wave benchmark data from the open guided waves platform, where delamination defects were simulated at multiple positions on a carbon fiber reinforced plastic plate under varying temperature conditions, the authors could identify suitable frequencies for further investigations and experiments. Furthermore, the authors presented a realistic validation scenario which ensures that the machine learning model learns global damage characteristics rather than position specific characteristics. T2 - 48th Annual Review of Progress in Quantitative Nondestructive Evaluation CY - Online meeting DA - 28.07.2021 KW - Machine Learning KW - Guided waves KW - Damage Detection KW - Structural Health Monitoring KW - Composite Structures PY - 2021 AN - OPUS4-53377 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Shapovalov, Oleg A1 - Shapovalova, M. A1 - Ossenbrink, R. A1 - Heckel, Thomas A1 - Michailov, V. A1 - Weiss, S. A1 - Gaal, Mate T1 - Verbessern der Korrosionsbeständigkeit eines hochtemperaturbeständigen Ultraschalldämpfungskörpers mittels Laserstrahl-Auftragschweißen N2 - Während in einem konventionellen Ultraschallprüfkopf ein Kunststoffdämpfungskörper mit Kleber oder Öl an einen Piezoschwinger angekoppelt ist, werden als Hochtemperaturlösung feinporöse sintermetallische Dämpfungsmaterialien mit einer Flüssigglasankopplung eingesetzt. Um dabei das Sintermetall vor dem korrosiven Angriff der Glasschmelze zu schützten, wird am Dämpfungskörper gegenwärtig Gold- oder Platinfolie zeit- und kostenaufwendig appliziert. In der aktuellen Arbeit wurde eine Methode zum Korrosionsschutz der sintermetallischen Oberfläche aus rostfreiem Stahl mittels Laser-Pulverauftragschweißen entwickelt. Im Laufe einer Schweißparameterstudie auf dem Substratmaterial aus massivem rostfreiem Stahl wurde die Eignung unterschiedlicher Auftragsmaterialien auf Nickel- und Kobaltbasis untersucht. Dabei wurde zunächst der Einfluss verschiedener Schweißparameter wie Laserleistung, Vorschubgeschwindigkeit und Pulvermenge auf die Auftragsqualität (Nahtform, Vermischungsgrad, Porosität) metallografisch bewertet. Anschließend wurden die aufgetragenen Schichten hinsichtlich ihrer Korrosionsbeständigkeit getestet. Der Kontakt mit einer flüssigen Glasmischung bei 500 °C hat bei keiner der beschichteten Proben sichtbare Korrosionswirkung gezeigt. Als Resultat der Schweißparameterstudie haben sich besonders die nickelbasierten Pulver als gut geeignete Materialien für den Prozess gezeigt. Die identifizierten Schweißparameter wurden im nächsten Schritt erfolgreich an das sintermetallische Substrat angepasst. T2 - DVS Congress CY - Online meeting DA - 14.09.2021 KW - Korrosion KW - Hochtemperaturbeständigkeit KW - Ultraschallwandler PY - 2021 SN - 978-3-96144-146-4 SN - 978-3-96144-147-1 VL - 2021 SP - 370 EP - 377 AN - OPUS4-53362 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jurgelucks, B. T1 - Defect Characterization in Carbon Fiber Reinforced Polymer via Derivative-based Optimization N2 - In recent years carbon über polymers have become a popular light-weight substitute for high-weight materials such as steel. One advantage of carbon fiber polymers is the high strength-to-weight ratio, thus some popular application areas are weight sensitive such as aeronautics or automobiles. As these application areas are especially sensitive to material failure it is of significant interest to characterize material defects which may arise. In this talk we will propose a method to characterize material defects in carbon fiber reinforced polymers using gradient-based optimization methods. The procedure is based on the solution of an inverse problem where simulation data and experimental data is fitted. Here, gradients of the simulation will be supplied by an Algorithmic Differentiation (AD) tool which greatly enhances the quality of the solution. Numerical examples will be provided. T2 - GAMM 2020@21 CY - Online meeting DA - 15.03.2021 KW - Inverse Method KW - Scaled Boundary Finite Element Method KW - Algorithmic Differentiation PY - 2021 AN - OPUS4-52896 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zeipert, H. A1 - Claes, L. A1 - Johannesmann, S. A1 - Lugovtsova, Yevgeniya A1 - Nicolai, Marcel A1 - Prager, Jens A1 - Henning, Bernd ED - Jumar, U. T1 - An approach to adhesive bond characterisation using guided acoustic waves in multi-layered plates N2 - An approach for the non-destructive characterisation of adhesive bonds using guided ultrasonic waves is presented. Pulsed laser radiation is used to thermoacoustically excite broadband ultrasonic waves in a multi-layered sample, consisting of a metal plate adhesively joined to a polymeric layer using synthetic resin. The resulting signals are received by a purpose-built piezoelectric transducer. Varying the distance between excitation and detection yields spatio-temporal measurement data, from which the dispersive properties of the propagating waves can be inferred using a two-dimensional Fourier transform, assuming the plates to act as coupled waveguides. Coupled multi-layered waveguides show an effect referred to as mode repulsion, where the distance between certain modes in the frequency-wavenumber domain is assumed to be a measure of coupling strength. Measurements at different stages of curing of the adhesive layer are performed and evaluated. A comparison of the results shows changes in the dispersive properties, namely an increased modal bandwidth for the fully cured sample as well as an increased modal distance. KW - Adhesive bonding KW - Guided waves KW - Non-destructive testing KW - Ultrasound PY - 2021 DO - https://doi.org/10.1515/auto-2021-0089 VL - 69 IS - 11 SP - 962 EP - 969 PB - De Gruyter CY - Berlin/Boston AN - OPUS4-53762 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gaal, Mate T1 - Schallfeldvermessungen von luftgekoppelten Ultraschallwandlern N2 - Zur Charakterisierung von Ultraschallwandlern finden unterschiedliche Methoden und Verfahren Anwendung. Während sich die ISO 22232:2021 verstärkt auf die Charakterisierung von Kontakt- und Tauchtechnikprüfköpfen konzentriert, wird über eine einheitliche Charakterisierung von luftgekoppelten Wandlern noch diskutiert. Durch die unterschiedlichen Herangehensweisen beinhalten Prüfkopf-Datenblätter oft unterschiedliche Prüfkopfparameter und Schallfeldgrößen, was einen direkten Vergleich und eine Applikation im Feld erschwert. So werden bspw. Wandler nach ISO 22232:2021 standardmäßig im Impuls-Echo-Betrieb charakterisiert. Allerdings ist dies nicht auf die in den letzten Jahren entwickelten luftgekoppelten Wandlertechnologien übertragbar, die nur als Sender oder als Empfänger einsetzbar sind. Daher arbeiten aktuell Hersteller, Forschungseinrichtungen und Anwender gemeinsam im Rahmen des Unterausschusses „Luftgekoppelte Ultraschallprüfung“ der DGZfP an der Erstellung einer Richtlinie. Diese Richtlinie stellt dabei den Anspruch dar, die bestehende Normung um die luftgekoppelte Prüfung zu erweitern und somit die Vereinheitlichung der Charakterisierung dieser Wandler zu erleichtern. In diesem Beitrag werden daher verschiedene Methoden der Schallfeldvermessung vorgestellt, untereinander verglichen und ihre Grenzen beschrieben. Abschließend wird auf die besonders herausfordernde Charakterisierung von und mit breitbandigen luftgekoppelten Sendern und Empfängern eingegangen. T2 - Seminar des Fachausschusses Ultraschallprüfung Konventionelle und innovative Anwendungen der Ultraschallprüfverfahren CY - Berlin, Germany DA - 10.11.2021 KW - Luftgekoppelte Ultraschallprüfung KW - Schallfeld KW - Charakterisierung PY - 2021 AN - OPUS4-53750 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lugovtsova, Yevgeniya T1 - К определению прочности клеевого соединения в многослойных материалах путем исследования областей расталкивания бегущих упругих волн T1 - Towards the determination of adhesive bonding strength of multi-layered materials by investigating guided wave mode repulsion N2 - Бегущие упругие волны часто используются в области неразрушающего контроля для определения механических характеристик материалов. Поскольку склеивание различных материалов является широко используемым методом в автомобильной и авиационной промышленности, необходима надежная система измерения для определения качества таких клеевых соединений. Дисперсионные кривые для многослойных волноводов при наличии клеевых прослоек характеризуются появлением эффекта расталкивания нормальных мод в тех областях, где соответствующие моды для отдельных материалов пересекались бы. Таким образом, в зависимости от качества клеевого соединения расстояние между этими модами изменяется. Используя комбинацию экспериментальных и численных данных, в настоящей работе представлен подход к определению параметра, указывающего на качество клеевого соединения. T2 - XXX Всероссийская школа-конференция МАТЕМАТИЧЕСКОЕ МОДЕЛИРОВАНИЕ В ЕСТЕСТВЕННЫХ НАУКАХ CY - Perm, Russia DA - 06.10.2021 KW - многослойный волновод KW - волны лэмбовского типа KW - контроль качества клеевого соединения PY - 2021 AN - OPUS4-53768 LA - rus AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lugovtsova, Yevgeniya A1 - Zeipert, H. A1 - Johannesmann, S. A1 - Nicolai, Marcel A1 - Prager, Jens A1 - Henning, B. T1 - К определению прочности клеевого соединения в многослойных материалах путем исследования областей расталкивания бегущих упругих волн T1 - Towards the determination of adhesive bonding strength of multi-layered materials by investigating guided wave mode repulsion N2 - Бегущие упругие волны часто используются в области неразрушающего контроля для определения механических характеристик материалов. Поскольку склеивание различных материалов является широко используемым методом в автомобильной и авиационной промышленности, необходима надежная система измерения для определения качества таких клеевых соединений. Дисперсионные кривые для многослойных волноводов при наличии клеевых прослоек характеризуются появлением эффекта расталкивания нормальных мод в тех областях, где соответствующие моды для отдельных материалов пересекались бы. Таким образом, в зависимости от качества клеевого соединения расстояние между этими модами изменяется. Используя комбинацию экспериментальных и численных данных, в настоящей работе представлен подход к определению параметра, указывающего на качество клеевого соединения. T2 - XXX Всероссийская школа-конференция МАТЕМАТИЧЕСКОЕ МОДЕЛИРОВАНИЕ В ЕСТЕСТВЕННЫХ НАУКАХ CY - Online meeting DA - 06.10.2021 KW - многослойный волновод KW - волны лэмбовского типа KW - контроль качества клеевого соединения PY - 2021 SP - 1 EP - 3 AN - OPUS4-53769 LA - rus AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gaal, Mate T1 - Sound field measurements on thermoacoustic air-coupled transducers N2 - There are many different methods to characterize air-coupled ultrasonic transducers for non-destructive testing. Data sheets of various manufacturers contain information about some parameters important for the performance of transducers, but this information is not standardized, so that a comparison between probes of different manufacturers is difficult. Therefore, the German Society for Non-Destructive Testing (DGZfP) is working on a guideline to characterization of air-coupled probes. One of the topics in this guideline is the application of thermoacoustic transducers for the characterization of receivers and another topic is the application of microphones for the characterization of transmitters. In this presentation we compare various characterization methods with the particular focus on the characterization of thermoacoustic transducers using an optical microphone. Both thermoacoustic transmitters and optical microphones have a very large bandwidth compared to conventional air-coupled transducers, but their spectrum is not entirely linear, which needs to be taken into account if they are applied as reference transducers. T2 - JSNDI online workshop “Emerging Technologies of Advanced Ultrasonic Measurement” CY - Online meeting DA - 14.12.2021 KW - Air-coupled ultrasound KW - Transducer KW - Sound field PY - 2021 AN - OPUS4-54195 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kanzler, D. T1 - Prüf‘ ich noch – oder mess‘ ich schon? Ein Konzept für die Prüfunsicherheitsbestimmung von zerstörungsfreien Prüfsystemen N2 - Häufig stellt sich die Frage, ob eine Materialinhomogenität kritisch für die strukturelle Integrität eines Bauteils ist. Dies ist häufig abhängig von der Größe und der Geometrie dieser Materialinhomogenität. Während die korrekte Bestimmung einer Defektgröße zweifelsfrei eine Messaufgabe darstellt, ist die Detektion eines Materialdefekts die Hauptaufgabe eines Prüfsystems. Allerdings sind manche Defekte zu klein, um detektiert zu werden. Es ist jedoch schwierig, etwas zu bemessen, was nur schwer gefunden werden kann, stellen sowohl die Detektion als auch die Fähigkeit den Defekt zu bemaßen, Teile der der Bewertung eines Prüfsystems dar. Die vorliegende Publikation beschäftigt sich zum einen mit der Notwendigkeit, die Auffindwahrscheinlichkeit von Prüfverfahren zu bewerten, und zum anderen mit den Schritten, mit denen das Konzept der Prüfunsicherheitsbewertung national und international vorangetrieben wird. Final werden die Methoden evaluiert, die den Schulterschluss zwischen Prüf- und Messunsicherheitsbestimmung ermöglichen. Ergänzt wird der Artikel mit Beispielen aus der Industrie, welche die aktuelle Relevanz des Themas untermauern. T2 - 10. VDI-Fachtagung Messunsicherheit praxisgerecht bestimmen – Prüfprozesse in der industriellen Praxis 2021 - Der Weg zum sicheren Messen und Prüfen CY - Erfurt, Germany DA - 10.11.2021 KW - Zerstörungsfreie Prüfung KW - Zuverlässigkeit KW - Human Factors KW - Probability of detection PY - 2021 AN - OPUS4-54248 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kanzler, D. A1 - Rentala, V. A1 - Bertovic, Marija A1 - Heckel, Thomas A1 - Rosenthal, Martina A1 - Keßler, S. A1 - Stolz, R. A1 - Dethof, F. A1 - Jüngert, A. A1 - Vrana, J. T1 - Prüf‘ ich noch – oder mess‘ ich schon? Ein Konzept für die Prüfunsicherheitsbestimmung von zerstörungsfreien Prüfsystemen N2 - Häufig stellt sich die Frage, ob eine Materialinhomogenität kritisch für die strukturelle Integrität eines Bauteils ist. Dies ist häufig abhängig von der Größe und der Geometrie dieser Materialinhomogenität. Während die korrekte Bestimmung einer Defektgröße zweifelsfrei eine Messaufgabe darstellt, ist die Detektion eines Materialdefekts die Hauptaufgabe eines Prüfsystems. Allerdings sind manche Defekte zu klein, um detektiert zu werden. Es ist jedoch schwierig, etwas zu bemessen, was nur schwer gefunden werden kann, stellen sowohl die Detektion als auch die Fähigkeit den Defekt zu bemaßen, Teile der der Bewertung eines Prüfsystems dar. Die vorliegende Publikation beschäftigt sich zum einen mit der Notwendigkeit, die Auffindwahrscheinlichkeit von Prüfverfahren zu bewerten, und zum anderen mit den Schritten, mit denen das Konzept der Prüfunsicherheitsbewertung national und international vorangetrieben wird. Final werden die Methoden evaluiert, die den Schulterschluss zwischen Prüf- und Messunsicherheitsbestimmung ermöglichen. Ergänzt wird der Artikel mit Beispielen aus der Industrie, welche die aktuelle Relevanz des Themas untermauern. T2 - 10. VDI-Fachtagung Messunsicherheit praxisgerecht bestimmen – Prüfprozesse in der industriellen Praxis 2021 CY - Erfurt, Germany DA - 10.11.2021 KW - Zerstörungsfreie Prüfung KW - Zuverlässigkeit KW - Probability of detection KW - Messunsicherheit KW - Human factors PY - 2021 SN - 978-3-18-102390-7 DO - https://doi.org/10.51202/9783181023907-367 SN - 0083-5560 VL - VDI-Bericht 2390 SP - 367 EP - 372 PB - VDI Verlag CY - Düsseldorf AN - OPUS4-54250 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schnur, C. A1 - Moll, J. A1 - Lugovtsova, Yevgeniya A1 - Schütze, A. A1 - Schneider, T. T1 - Explainable machine learning for damage detection - In carbon fiber composite plates under varying temperature conditions N2 - Understanding on how a machine learning model interprets data is a crucial step to verify its reliability and avoid overfitting. While the focus of the scientific community is nowadays orientated towards deep learning approaches, which are considered as black box approaches, this work presents a toolbox that is based on complementary methods of feature extraction and selection, where the classification decisions of the model are transparent and can be physically interpreted. On the example of guided wave benchmark data from the open guided waves platform, where delamination defects were simulated at multiple positions on a carbon fiber reinforced plastic plate under varying temperature conditions, the authors could identify suitable frequencies for further investigations and experiments. Furthermore, the authors presented a realistic validation scenario which ensures that the machine learning model learns global damage characteristics rather than position specific characteristics. T2 - 48th Annual Review of Progress in Quantitative Nondestructive Evaluation CY - Online meeting DA - 28.07.2021 KW - Explainable machine learning KW - Guided waves KW - Damage detection KW - Structural health monitoring KW - Composite structures PY - 2021 SN - 978-0-7918-8552-9 DO - https://doi.org/10.1115/QNDE2021-75215 SP - 1 EP - 6 PB - American Society of Mechanical Engineers (ASME) CY - New York, NY AN - OPUS4-54219 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Kudela, P. A1 - Radzienski, M. A1 - Moix-Bonet, M. A1 - Willberg, C. A1 - Lugovtsova, Yevgeniya A1 - Bulling, Jannis A1 - Tschöke, K. A1 - Moll, J. T1 - Dataset on full ultrasonic guided wavefield measurements of a CFRP plate with fully bonded and partially debonded omega stringer N2 - The fourth dataset dedicated to the Open Guided Waves platform presented in this work aims at a carbon fiber composite plate with an additional omega stringer at constant temperature conditions. The dataset provides full ultrasonic guided wavefields. A chirp signal in the frequency range 20-500 kHz and Hann windowed tone-burst signal with 5 cycles and carrier frequencies of 16.5 kHz, 50 kHz, 100 kHz, 200 kHz and 300kHz are used to excite the wave. The piezoceramic actuator used for this purpose is attached to the center of the stringer side surface of the core plate. Three scenarios are provided with this setup: (1) wavefield measurements without damage, (2) wavefield measurements with a local stringer debond and (3) wavefield measurements with a large stringer debond. The defects were caused by impacts performed from the backside of the plate. As result, the stringer feet debonds locally which was verified with conventional ultrasound measurements. The dataset can be used for benchmarking purposes of various signal processing methods for damage imaging. The detailed description of the dataset is published in Data in Brief Journal. KW - Open data KW - Ultrasonic guided waves KW - Experimental data PY - 2021 DO - https://doi.org/10.5281/zenodo.5105861 PB - Zenodo CY - Geneva AN - OPUS4-54504 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Held, Mathias T1 - Inverse determination of elastic material parameters from the propagation behavior of ultrasonic waves using convolutional neuronal networks N2 - Um aus messtechnisch ermittelten Dispersionsabbildungen geführter Ultraschallwellen Rückschlüsse auf die Materialparameter zu ziehen, werden in der aktuellen Forschung verschiedene inverse Methoden diskutiert. Maschinelles Lernen und insbesondere Convolutional-Neural-Networks (CNNs) stellen eine Möglichkeit der automatisierten inversen Modellierung und Evaluierung von Bilddaten dar. In diesem Vortrag wird anhand synthetischer Daten gezeigt, wie das Ausbreitungsverhalten von geführten Ultraschallwellen unter Verwendung von CNNs genutzt werden kann, um die isotropen elastischen Konstanten einer plattenförmigen Struktur zu bestimmen. T2 - Doktorandentreffen 2021 CY - Petershagen/Eggersdorf, Germany DA - 25.10.2021 KW - Convolutional Neuronal Networks KW - Inverse Probleme KW - Materialcharakterisierung KW - Maschine learning KW - Guided waves KW - Lamb Wellen PY - 2021 AN - OPUS4-54264 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heckel, Thomas T1 - Charakterisierung und Verifizierung der Ultraschall-Prüfausrüstung - Die Normenreihe DIN EN ISO 22232 ersetzt die DIN EN 12668 seit September 2021 N2 - Durch die Internationalisierung in der Standardisierung wurden die Regelwerke zur „Charakterisierung und Verifizierung der Ultraschall-Prüfausrüstung“, die bisher als europäische Regelwerke der DIN EN 12668 Reihe eingeordnet waren, überarbeitet und in internationale Regelwerke überführt. Die Regelwerke sind seit September 2021 als deutsche Übersetzung eingeführt als DIN EN ISO 22232 und ersetzen somit in Deutschland die bisher geltenden Regelwerke der DIN EN 12668 Reihe. Die drei Teile der Reihe beschäftigen sich in Teil 1 mit den Prüfgeräten, in Teil 2 mit den Prüfköpfen und in Teil 3 mit der Prüfausrüstung, die aus Prüfgerät, Prüfkopf und Kabel besteht. In dem Vortrag möchten wir neben dem historischen Werdegang darlegen, welche Gemeinsamkeiten und Unterschiede die Regelwerke aufweisen und worauf bei der Umstellung zu achten ist. T2 - Arbeitskreis Berlin der DGZfP – 431. Sitzung CY - Online meeting DA - 9.11.2021 KW - Ultraschall KW - Zerstörungsfreie Prüfung KW - Standardisierung KW - Gerätetechnik PY - 2021 AN - OPUS4-54308 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hassenstein, Christian T1 - Adaptive TFM approach for turbine blade testing in an NDE 4.0 environment N2 - Turbine blades for gas turbines are exposed to extreme working conditions in a demanding environment. In-service inspection, maintenance and refurbishment of the heavily stressed parts is necessary to ensure both safety and efficiency, e.g. based on immersion ultrasound testing (UT). In the course of NDE 4.0, the European project MRO 2.0 aims to innovate the maintenance, repair and overhaul of turbine blades by linking these with modern digital methods. For this, the goal of this project is to go beyond conventional automated and manual UT testing techniques. The aim is to measure the actual geometry and wall thickness of the complex shaped parts by applying an adaptive TFM that takes into account the refraction of the ultrasonic waves at the transition from the coupling material (water) to the inspected part (steel). In this setup the phased array probe is held by a robotic arm that allows the part to be scanned while remaining mainly perpendicular to the inspected surface. In this way, even complex geometries can be inspected and a 3D model of the actual condition of the part can be created. The laboratory setup is equipped with a Vantage 64 phased array instrument from Verasonics Inc. and an industrial robot from ABB. A 64 element linear array probe operating at 10 MHz is attached to the robot. The focus is on optimizing resolution, reliability and inspection speed, as the reconstructed model will be fed to the digital twin at a later stage of the project and used for targeted repairs. In addition to enhancing the reconstruction algorithms, required probe geometry and the parameters needed to inspect turbine blades with partially thin walls and anisotropic materials will also be investigated. This talk will describe the 3-year project and present the results of the first year. The main focus will be on the development of the reconstruction algorithms used and the experimental setup. T2 - 48th Annual Review of Progress in Quantitative Nondestructive Evaluation (QNDE 2021) CY - Online meeting DA - 28.07.2021 KW - Utrasound testing KW - Turbine blade KW - Maintenance KW - Phased array KW - Automation PY - 2021 AN - OPUS4-54313 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Prager, Jens A1 - Lugovtsova, Yevgeniya A1 - Bulling, Jannis A1 - Held, Mathias A1 - Klärner, M. A1 - Winkler, T. A1 - Kroll, L. T1 - Akustische Bestimmung der Werkstoffparameter faserverstärkter Kunststoffe durch Auswertung der Dispersionseigenschaften geführter Wellen N2 - Akustische Verfahren eignen sich hervorragend zur Bestimmung der Werkstoffeigenschaften. Die Verfügbarkeit derartiger Verfahren ist vor allem für Kunststoffe wichtig, da deren Eigenschaften stark abhängig vom jeweiligen Herstellungsprozess und vom Alterungszustand sind. Exakte und vollständige Werte sind daher in Datenbanken oder von Herstellern nur begrenzt zu finden. Insbesondere die Entwicklung von Methoden zur Charakterisierung faserverstärkter Kunststoffe (FKV) ist nach wie vor Gegenstand der Forschung. Hier müssen anisotropiebedingt mehrere Kennwerte bestimmt werden. Da FKV zumeist als dünnwandige Bauteile zum Einsatz kommen, können die Werkstoffparameter aus den Dispersionseigenschaften der Lamb-Wellen, die sich in diesen Strukturen ausbreiten, abgeleitet werden. Dazu ist eine räumliche Abtastung des sich ausbreitenden Schallfelds erforderlich. In der vorliegenden Untersuchung wird dieser Ansatz für die relativ neue Werkstoffklasse der faserverstärkten Thermoplaste angewendet. Diese zeichnet ein ausgeprägtes Dämpfungsverhalten und eine Anisotropie der Materialparameter aus. Dazu wurde das Schallfeld im Ultraschallbereich mit einem Laser-Doppler-Vibrometers vermessen. Rechnerisch bestimmte Dispersionskurven wurden dann an die gemessenen Werte angepasst, womit die richtungsabhängigen Materialparameter bestimmt werden konnten. Im Vortrag wird das Messverfahren vorgestellt und auf spezielle Probleme, die sich z.B. aus dem Dämpfungsverhalten des Werkstoffs ergeben, eingegangen. Ausgewählte gemessene Werte werden mit den Ergebnissen von Referenzverfahren verglichen. T2 - DAGA 2021 - 47. Jahrestagung für Akustik CY - Vienna, Austria DA - 15.08.2021 KW - Ultraschall KW - Composites KW - Thermoplastische Kunststoffe PY - 2021 SP - 52 EP - 55 PB - Deutsche Gesellschaft für Akustik (DEGA) CY - Berlin AN - OPUS4-57340 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Prager, Jens T1 - Akustische Bestimmung der Werkstoffparameter faserverstärkter Kunststoffe mittels geführter Wellen N2 - Akustische Verfahren eignen sich hervorragend zur Bestimmung der Werkstoffeigenschaften. Die Verfügbarkeit derartiger Verfahren ist vor allem für Kunststoffe wichtig, da deren Eigenschaften stark abhängig vom jeweiligen Herstellungsprozess und vom Alterungszustand sind. Exakte und vollständige Werte sind daher in Datenbanken oder von Herstellern nur begrenzt zu finden. Insbesondere die Entwicklung von Methoden zur Charakterisierung faserverstärkter Kunststoffe (FKV) ist nach wie vor Gegenstand der Forschung. Hier müssen anisotropiebedingt mehrere Kennwerte bestimmt werden. Da FKV zumeist als dünnwandige Bauteile zum Einsatz kommen, können die Werkstoffparameter aus den Dispersionseigenschaften der Lamb-Wellen, die sich in diesen Strukturen ausbreiten, abgeleitet werden. Dazu ist eine räumliche Abtastung des sich ausbreitenden Schallfelds erforderlich. In der vorliegenden Untersuchung wird dieser Ansatz für die relativ neue Werkstoffklasse der faserverstärkten Thermoplaste angewendet. Diese zeichnet ein ausgeprägtes Dämpfungsverhalten und eine Anisotropie der Materialparameter aus. Dazu wurde das Schallfeld im Ultraschallbereich mit einem Laser-Doppler-Vibrometers vermessen. Rechnerisch bestimmte Dispersionskurven wurden dann an die gemessenen Werte angepasst, womit die richtungsabhängigen Materialparameter bestimmt werden konnten. Im Vortrag wird das Messverfahren vorgestellt und auf spezielle Probleme, die sich z.B. aus dem Dämpfungsverhalten des Werkstoffs ergeben, eingegangen. Ausgewählte gemessene Werte werden mit den Ergebnissen von Referenzverfahren verglichen. T2 - DAGA 2021 - 47. Jahrestagung für Akustik CY - Vienna, Austria DA - 15.08.2021 KW - Ultraschall KW - Composites KW - Thermoplastische Kunststoffe PY - 2021 AN - OPUS4-57344 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schnur, C. A1 - Moll, J. A1 - Lugovtsova, Yevgeniya A1 - Schütze, A. A1 - Schneider, T. ED - Kundu, T. ED - Reis, H. ED - Ihn, J.-B. ED - Dzenis, Y. T1 - Explainable Machine Learning for Damage Detection: in Carbon Fiber Composite Plates Under Varying Temperature Conditions N2 - Understanding on how a machine learning model interprets data is a crucial step to verify its reliability and avoid overfitting. While the focus of the scientific community is nowadays orientated towards deep learning approaches, which are considered as black box approaches, this work presents a toolbox that is based on complementary methods of feature extraction and selection, where the classification decisions of the model are transparent and can be physically interpreted. On the example of guided wave benchmark data from the open guided waves platform, where delamination defects were simulated at multiple positions on a carbon fiber reinforced plastic plate under varying temperature conditions, the authors could identify suitable frequencies for further investigations and experiments. Furthermore, the authors presented a realistic validation scenario which ensures that the machine learning model learns global damage characteristics rather than position specific characteristics. T2 - 2021 48th Annual Review of Progress in Quantitative Nondestructive Evaluation CY - Online meeting DA - 28.07.2021 KW - Explainable machine learning KW - Guided waves KW - Damage detection KW - Structural health monitoring KW - Composite structures PY - 2021 SN - 978-0-7918-8552-9 DO - https://doi.org/10.1115/QNDE2021-75215 VL - QNDE2021-75215 SP - 1 EP - 6 PB - The American Society of Mechanical Engineers (ASME) CY - New York, USA AN - OPUS4-56723 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pelkner, Matthias T1 - Process monitoring in metal AM@BAM, the project ProMoAM N2 - In this presentation we give an overview of activities regarding non-destructive testing of AM components during the manufacturing process. For this purpose, we installed different NDT methods inside the AM systems. The results obtained during the manufacturing process are presented and discussed. T2 - 74th IIW Annual Assembly and International Conference CY - Online meeting DA - 07.07.2021 KW - Non-destructive testing KW - Additive manufacturing KW - Online monitoring PY - 2021 AN - OPUS4-53186 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tiebe, Carlo T1 - Prüf- und Messverfahren mit verschiedenen Sensortechnologien und Ultraschallwellen N2 - Der Vortrag zum Mess- und Prüfverfahren mit verschiedenen Sensortechnologien und Ultraschallwellen beinhaltet die Themen: Metrologie zur Wasserstoffspeicherung - Euramet-Vorhaben "MefHySto", Erkennung von freigesetztem Wasserstoff sowie die Bestimmung des Wasserstoff-Luftverhälntisses mit Gassensoren, zerstörungsfreie Fehlstellenerkennung mit integriertem Zustandsüberwachungssystem basierend auf geführten Ultraschallwellen zur Lebensdauerüberwachung von Composite-Behältern (Wasserstoffspeicher) sowie faseroptische Sensorik zur Schadenfrüherkennung von Wasserstoffspeichern aufgrund erkennbarer Dehnungsänderungen an Druckbehältern. T2 - DVGW Kongress H2 Sicherheit CY - Online meeting DA - 28.09.2021 KW - Leckdetektion KW - Metrologie zur Wasserstoffspeicherung KW - Gassensorik KW - Structural Health Monitoring (SHM) KW - Geführte Ultraschallwellen KW - Faseroptische Sensorik KW - Zerstörungsfreie Prüfung PY - 2021 AN - OPUS4-54136 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tiebe, Carlo T1 - Mess- und Prüfverfahren mit Sensorik N2 - Mess- und prüftechnische Verfahren sind zur Prozesskontrolle und Sicherheitsüberwachung in Wasserstofftechnologien von hoher Bedeutung. Typische Anwendungsgebiete von Sensoren sind Sicherheitsüberwachung, Leckdetektion und Prozesskontrolle. In diesem Beitrag werden Themen zur Erkennung von freigesetztem Wasserstoff sowie die Bestimmung des Wasserstoff-Luftverhältnisses mit Gassensoren, Fehlstellenerkennung mit geführten Ultraschallwellen zur Lebensdauerüberwachung (Structural Health Monitoring) von Wasserstoffspeichern sowie der Einsatz faseroptischer Sensoren zur Überwachung des Dehnungs- und Alterungsverhaltens sowie zur Schadensfrüherkennung von Wasserstoffspeichern vorgestellt. T2 - DVGW Kongress H2 Sicherheit CY - Online meeting DA - 27.01.2021 KW - Metrologie KW - Gassensoren KW - Structural Health Monitoring KW - Faseroptische Sensoren KW - Wasserstoff PY - 2021 AN - OPUS4-52141 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kudela, P. A1 - Radzienski, M. A1 - Moix-Bonet, M. A1 - Willberg, C. A1 - Lugovtsova, Yevgeniya A1 - Bulling, Jannis A1 - Tschöke, K. A1 - Moll, J. T1 - Dataset on full ultrasonic guided wavefield measurements of a CFRP plate with fully bonded and partially debonded omega stringer N2 - The fourth dataset dedicated to the Open Guided Waves platform presented in this work aims at a carbon fiber composite plate with an additional omega stringer at constant temperature conditions. The dataset provides full ultrasonic guided wavefields. Two types of signals were used for guided wave excitation, namely chirp signal and tone-burst signal. The chirp signal had a frequency range of 20-500kHz. The tone-burst signals had a form of sine modulated by Hann window with 5 cycles and carrier frequencies 16.5kHz, 50kHz, 100kHz, 200kHz, 300kHz. The piezoceramic actuator used for this purpose was attached to the center of the stringer side surface of the core plate. Three scenarios are provided with this setup: (1) wavefield measurements without damage, (2) wavefield measurements with a local stringer debond and (3) wavefield measurements with a large stringer debond. The defects were caused by impacts performed from the backside of the plate. As result, the stringer feet debonds locally which was verified with conventional ultrasound measurements. KW - Lamb waves KW - Composite panel KW - Impact damage KW - Damage detection KW - Scanning laser Doppler vibrometry KW - Structural health monitoring KW - Non-destructive evaluation KW - Open data PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-545242 DO - https://doi.org/10.1016/j.dib.2022.108078 SN - 2352-3409 VL - 42 SP - 1 EP - 13 PB - Elsevier CY - Amsterdam AN - OPUS4-54524 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -