TY - CONF A1 - Gaal, Mate A1 - Schadow, Florian A1 - Bartusch, Jürgen A1 - Beck, Uwe A1 - Daschewski, Maxim A1 - Kreutzbruck, Marc T1 - Airborne ultrasonic systems for one-sided inspection using thermoacoustic transmitters N2 - Airborne ultrasonic inspection is performed in through transmission, where the test piece (e.g. adhesive joint or polymer-based composite plate) is placed between the transmitter and the receiver. However, many structures with difficult shapes allow only one-sided inspection. The strong reflection of the signal from the surface overshadows the signals from the inside, so that broadband pulses are required. Thermoacoustic transmission, where the thermal energy of an electrically heated electrode is transformed into the acoustic energy of an ultrasonic wave, opens the possibility to excite broadband pulses and thus to inspect objects with one-sided access. We present various thermoacoustic transducers consisting of an electrically conductive film on a solid substrate. The first type of transducer is a transmitter with an indium-tin-oxide electrode on a glass substrate combined with a laser Doppler vibrometer as a receiver. The second type of transducer combines thermoacoustic transmission and piezoelectric reception, having a titanium electrode as a transmitter deposited onto charged cellular polypropylene serving as a piezoelectric receiver. Using a focusing thermoacoustic transmitter and a separate cellular polypropylene receiver, a through-transmission inspection of a 4 mm thick CFRP test piece with inserts as small as 1 mm was performed. The same emitter and a laser vibrometer as a receiver were used for a one-sided inspection of a Plexiglas block with a cross hole at 15 mm depth. A twin probe consisting of a thermoacoustic transmitter on a cellular polypropylene receiver was applied to a profile measurement on a step wedge with flat bottom holes. The smallest detected diameter of a flat bottom hole was 1 mm. Sound pressure level above 140dB was achieved with each of these transmitters. Thermoacoustic transmitters enable a step towards one-sided air-coupled ultrasonic inspection. T2 - IEEE International Ultrasonics Symposium CY - Tours, France DA - 18.9.2016 KW - Airborne KW - Air-coupled KW - Ferroelectret KW - Thermoacoustic KW - Ultrasonic transducer PY - 2016 AN - OPUS4-37621 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst A1 - Ertel, Jens-Peter A1 - Sochor, M. A1 - Unseld, H. T1 - Nachbestimmung von Pfahllängen am Beispiel von Masten N2 - Im Rahmen der Lebensdauerverlängerung oder der Umnutzung von Bauwerken (z. B. Brücken, Bürogebäude oder Maste) müssen diese zum Teil neu bewertet werden. Dafür ist eine Nachrechnung für statische und dynamische Lastfälle erforderlich. Dies betrifft zum einen die Struktur selbst, die gegebenenfalls verstärkt werden muss. Aber auch die Gründung (oft Pfähle verschiedenster Typen) muss neu beurteilt werden. Nach mehreren Jahrzehnten sind jedoch für einige Bauwerke keine zuverlässigen Bestandsunterlagen verfügbar. Eine vollständige Freilegung der Pfähle verbietet sich aus Kostengründen sowie Verlust an Widerstand gegen Zug. Lediglich der Pfahlanschluss kann visuell begutachtet werden, um Pfahlzahl, -typ und Durchmesser zu bestimmen. Für die Bestimmung der Pfahllänge müssen zerstörungsfreie Verfahren eingesetzt werden. In einer Machbarkeitsstudie wurden von den Autoren teils im Blindversuch drei Verfahren evaluiert: die klassische Pfahlintegritätsprüfung nach der Hammerschlagmethode, eine mehrkanalige Variante hierzu und das Parallel-Seismik-Verfahren. Die ersten beiden Methoden lieferten an den untersuchten Pfählen nur in Einzelfällen verwertbare Ergebnisse. Die Parallel-Seismik-Methode lieferte auch im Blindversuch an Fundamenten, bei denen die Pfahllänge dem Eigentümer bekannt war, Ergebnisse mit einer Abweichung von max. 0,5 m. Diese Toleranz lässt sich bei der Standfestigkeitsbeurteilung berücksichtigen. Die Mehrkosten des Verfahrens (anders als bei den anderen Verfahren wird ein verrohrtes Bohrloch im Boden nahe dem Pfahl benötigt) halten sich in Grenzen, wenn man es in die geotechnische Untersuchung integriert. Daher wurde es inzwischen auch in der Praxis eingesetzt. Auch liegen die Gesamtkosten für die Untersuchung deutlich unter denen für eventuell notwendigen Ersatz – oder Verstärkungsmaßnahmen, die notwendig werden, wenn keine Daten zur Pfahllänge verfügbar sind. Der Vortrag erläutert die Ergebnisse der Machbarkeitsstudie, zeigt erste Praxisfälle und weist auf Möglichkeiten hin, das Parallel-Seismik Verfahren in Zukunft noch genauer und effizienter einzusetzen. T2 - Baugrundtagung 2016 CY - Bielefeld, Germany DA - 15.09.2016 KW - Mast KW - Pile KW - Pfahl KW - Länge KW - Parallel-Seismik KW - Integritätsprüfung KW - Tower KW - Length KW - Parallel-seismic KW - Integrity-testing PY - 2016 AN - OPUS4-37647 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Griepentrog, Michael A1 - Beck, Uwe A1 - Reiners, Georg T1 - Kratzbeständigkeit Prüfmethoden und deren Bewertung N2 - Der Vortrag widmet sich der Kratzbeständigkeit-Prüfmethoden und deren Bewertung und beschreibt Begriffe/Definitionen, Wirtschaftliche Bedeutung der Kratzbeständigkeit, Mess- und Prüfverfahren – allgemein (Anwendbarkeit, Messunsicherheit, Validierung), Mess- und Prüfverfahren – speziell die Erzeugung, Prüfverfahren von Einzel- und Vielfach-Kratzern, die Charakterisierung von Verkratzungen und eine zusammenfassende Bewertung im Einzelnen T2 - SKZ-Seminare für die Kunststoff-Branche: Modifikation der Kratz- und Abriebbeständigkeit CY - Peine, Germany DA - 19.04.2016 KW - Kratzfestigkeit KW - Haftfestigkeit KW - Ritztest KW - Instrumentierte Eindringprüfung KW - Normung PY - 2016 AN - OPUS4-37598 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lehmann, Jens A1 - Ebell, Gino A1 - Burkert, Andreas T1 - Potentialfeldmessung - Korrosionsprüfung von Stahlbetonbauwerken N2 - Durch das alkalische Porenwassermilieu ist Stahl im Beton vor Korrosion geschützt. Unter un-günstigen Umgebungsbedingungen (Karbonatisierung, Chlorideintrag) kann die passive Deck-schicht auf der Stahloberfläche zerstört werden. Im weiteren Verlauf können sich korrosionsbe-dingte Folgeschäden, wie Risse und Abplatzungen am Bauwerk ergeben. Um notwendige Sanie-rungsmaßnahmen sind frühzeitige und weitgehend zerstörungsfrei ermittelte Informationen über das aktuelle Korrosionsverhalten der Stahlbewehrung von großer Bedeutung. Die Potentialfeld-messung ist ein etabliertes und weit verbreitetes Verfahren zur Beurteilung des Korrosionszu-standes der Bewehrung in Stahlbetonbauwerken. Mit Hilfe dieses Verfahrens können Bereiche aktiv korrodierender Bewehrung zerstörungsfrei lokalisiert werden. In der Regel kommt diese Messmethode bei der Detektion chloridinduzierter Korrosion zum Einsatz. T2 - Fachtagung Prüfen von Beton CY - Berlin, Germany DA - 06.10.2016 KW - Stahlbeton KW - Spannbeton KW - Korrosion KW - Zertörungsfreie Prüfung PY - 2016 AN - OPUS4-37711 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst T1 - Geophysik im Bauwesen - ein Überblick N2 - Überblick über den Einsatz verschiedener geophysikalischer Verfahren in der zerstörungsfreien Prüfung im Bauwesen T2 - Workshop Geophysikalische Untersuchungen an Bauwerken CY - Neustadt/W., Germany DA - 05.10.2016 KW - Geophysik KW - ZfP KW - Bauwesen PY - 2016 AN - OPUS4-37719 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst A1 - Ertel, Jens-Peter A1 - Sochor, M. A1 - Unseld, H. T1 - Nachbestimmung von Pfahllängen am Beispiel von Masten. N2 - Im Rahmen der Lebensdauerverlängerung oder der Umnutzung von Bauwerken (z. B. Brücken, Bürogebäude oder Maste) müssen diese zum Teil neu bewertet werden. Dafür ist eine Nachrechnung für statische und dynamische Lastfälle erforderlich. Dies betrifft zum einen die Struktur selbst, die gegebenenfalls verstärkt werden muss. Aber auch die Gründung (oft Pfähle verschiedenster Typen) muss neu beurteilt werden. Nach mehreren Jahrzehnten sind jedoch für einige Bauwerke keine zuverlässigen Bestandsunterlagen verfügbar. Eine vollständige Freilegung der Pfähle verbietet sich aus Kostengründen sowie Verlust an Widerstand gegen Zug. Lediglich der Pfahlanschluss kann visuell begutachtet werden, um Pfahlzahl, -typ und Durchmesser zu bestimmen. Für die Bestimmung der Pfahllänge müssen zerstörungsfreie Verfahren eingesetzt werden. In einer Machbarkeitsstudie wurden von den Autoren teils im Blindversuch drei Verfahren evaluiert: die klassische Pfahlintegritätsprüfung nach der Hammerschlagmethode, eine mehrkanalige Variante hierzu und das Parallel-Seismik-Verfahren. Die ersten beiden Methoden lieferten an den untersuchten Pfählen nur in Einzelfällen verwertbare Ergebnisse. Die Parallel-Seismik-Methode lieferte auch im Blindversuch an Fundamenten, bei denen die Pfahllänge dem Eigentümer bekannt war, Ergebnisse mit einer Abweichung von max. 0,5 m. Diese Toleranz lässt sich bei der Standfestigkeitsbeurteilung berücksichtigen. Die Mehrkosten des Verfahrens (anders als bei den anderen Verfahren wird ein verrohrtes Bohrloch im Boden nahe dem Pfahl benötigt) halten sich in Grenzen, wenn man es in die geotechnische Untersuchung integriert. Daher wurde es inzwischen auch in der Praxis eingesetzt. Auch liegen die Gesamtkosten für die Untersuchung deutlich unter denen für eventuell notwendigen Ersatz – oder Verstärkungsmaßnahmen, die notwendig werden, wenn keine Daten zur Pfahllänge verfügbar sind. Der Vortrag erläutert die Ergebnisse der Machbarkeitsstudie, zeigt erste Praxisfälle und weist auf Möglichkeiten hin, das Parallel-Seismik Verfahren in Zukunft noch genauer und effizienter einzusetzen. T2 - Workshop Geophysikalische Untersuchungen an Bauwerken CY - Neustadt/W., Germany DA - 05.10.2016 KW - Parallel-Seismik KW - Mast KW - Pfahl KW - Länge PY - 2016 AN - OPUS4-37720 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst A1 - Wiggenhauser, Herbert T1 - Coda wave interferometry used for monitoring of concrete constructions N2 - Ultrasonic transmission measurements on concrete; embedded transducers; coda wave interferometry to check for subtle chnages in velocity as indicator for various loads or deterioration. T2 - 76. Jahrestagung der Deutschen Geophysikalischen Gesellschaft CY - Münster, Germany DA - 14.03.2016 KW - Ultrasound KW - Transmission KW - Coda wave interferometry KW - Concrete KW - Load PY - 2016 AN - OPUS4-37721 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Griepentrog, Michael T1 - Ritz-Test: Evaluierung und Stand der Normung N2 - Der Vortrag widmet sich dem „RITZ-TEST: EVALUIERUNG UND STAND DER NORMUNG“ und beschreibt die Komponenten, Ergebnis und Messgrößen, nicht registrierende Prüfgeräte, Evaluierung Ritz-Test (Makrobereich), den Atlas der Versagensformen, Geräte für den instrumentierten Ritz-Test und die Normung des Ritz-Tests (ASTM) zur Bewertung der Haftfestigkeit“ im Einzelnen. T2 - EFDS, 17. Wörlitzer Workshop "Schichthaftung - Anwendungsbeispiele aus der Praxis" CY - Oranienbaum-Wörlitz, Germany DA - 06.06.2016 KW - Kratzfestigkeit KW - Haftfestigkeit KW - Ritztest KW - Instrumentierte Eindringprüfung KW - Normung PY - 2016 AN - OPUS4-38105 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schönhals, Andreas T1 - Broadband dielectric spectroscopy as an orthogonal tool to mechanical analysis – From theory to applications N2 - The basics of broadband dielectric spectroscopy were introduced in detail. The analysis of the data was discussed. As application of broadband dielectric spectroscopy the alpha-relaxation (dynamic glass transition), the chain dynamics of polymers, and the behavior of a high performance polymer were illustrated. T2 - Geesthachter Polymertage CY - Geesthcht, Germany DA - 08.11.2016 KW - Broadband dielectric spectroscopy PY - 2016 AN - OPUS4-38185 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst T1 - Inspection and monitoring of massive concrete structures by innovative ultrasonic methods N2 - Presentation on recent progress in ultrasinic testing and monitoring of concrete for massive structures. First, a new instrument (LAUS) for ultrasonic echo testing of thicknesses up to 5 m is shown. A new method to provide better images of the concrete interior, Reverse Mitem Migration (RTM)is presented. Second, the use of embedded ultrasonic transducers and data processing methods borrowed from seismology to detect subtle changes in concrete are documented. T2 - NUCCON 2016 CY - Helsinki, Finland DA - 31.10.2016 KW - Ultrasound KW - Concrete KW - Imaging KW - Monitoring KW - Nuclear PY - 2016 AN - OPUS4-38181 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kraft, Marco A1 - Würth, Christian A1 - Kaiser, Martin A1 - Muhr, Verena A1 - Hirsch, Thomas A1 - Resch-Genger, Ute T1 - Particle Size Dependent Absolute Photoluminescence Quantum Yields and Lifetimes of Hexagonal beta-NaYF4: 2 % Er3+, 20 % Yb3+ Upconversion Nanoparticles in Cyclohexane and Water N2 - Hexagonal beta-NaYF₄ doped with 20 % Yb and 2 % Er is an efficient upconversion (UC) phosphor for the conversion of 976 nm to 845 nm, 655 nm and 540 nm light. The emission behavior of this material is strongly influenced by the particle size, surface chemistry, and microenvironment. Especially the design of nm-sized UC particles for bioanalytical applications requires reliable spectroscopic tools for the characterization of the optical properties of these materials like the UC quantum yield (QYUC) in aqueous media. The UC emission originates from multiphotonic absorption processes, rendering the QYUC excitation power density (P) dependent. The P-dependent absolute measurement of QYUC in aqueous media with an excitation wavelength of 976 nm presents a considerable challenge due to the low absorption coefficients of the UC materials and the absorption of water at this wavelength. Here, we present the P-dependent QYUC of 21 nm, 26 nm and 31 nm-sized NaYF₄ UC particles dispersed in cyclohexane and aqueous solutions, in view of bioanalytical applications. To gain a better insight of the photonic nature of the upconversion mechanism and the quenching processes involved, the luminescence decay behavior as well as the P-dependent red-to-green luminescence intensity ratios and slope factors of the different emission bands are studied in both solvents. These results present an important step to the rational design of brighter upconversion nanoparticles. T2 - UPCON conference 2016 CY - Wroclaw, Poland DA - 23.05.2016 KW - Water KW - Upconversion KW - Quantum Yield KW - Lifetime KW - Cyclohexane PY - 2016 AN - OPUS4-38131 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Beck, Uwe A1 - Hertwig, Andreas T1 - Ringversuch zur Klassifizierung von Kohlenstoffschichten mittels Ellipsometrie N2 - Der Vortrag widmet sich dem „Ringversuch zur Klassifizierung von Kohlenstoffschichten mittels Ellipsometrie“ und beschreibt die experimentellen Eckdaten, die Ellipsometrie als Messmethode am Beispiel DLC auf Stahl, Proben vs. n-k Ebene vs. Ergebnisse des Ringversuches, messtechnische Bewertung des Ringversuches und normative Bewertung des Ringversuches sowie Schlussfolgerungen. T2 - 9. Sitzung DIN NA 062-01-64 „Kohlenstoffschichten“ CY - Berlin, Deutschland DA - 09.05.2016 KW - Amorphe Kohlenstoffschichten KW - Optische Konstanten KW - Ellipsometrie KW - Klassifizierungssystem PY - 2016 AN - OPUS4-38041 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Beck, Uwe A1 - Unger, Wolfgang A1 - Griepentrog, Michael A1 - Hertwig, Andreas T1 - Plasma Germany, Fachausschuss Normung, Herbstsitzung 2016 N2 - Der Stand der Normung im Bereich der Oberflächentechnik wird zusammengefasst. Aktuelle Normungsvorhaben zur chemischen Oberflächenanalyse, Rastersondenmikroskopie, Nanotechnologie, Oberflächenmesstechnik im Mikro- und Nanobereich, für Anwendungen von Kohlenstoffschichten sowie von Mess- und Prüfverfahren für metallische und anorganische Überzüge werden vorgestellt. Ein Ringversuch zur Klassifizierung von Kohlenstoffschichten mittels Ellipsometrie wird diskutiert. Abschließend wird das DIN-Terminologie Portal erläutert. T2 - Lenkungsausschuss von Plasma Germany, Fachausschuss Normung, Herbstsitzung 2016 CY - Stuttgart, Germany DA - 27.10.2016 KW - Stand der Normung KW - Oberflächentechnik KW - Schichttechnik PY - 2016 AN - OPUS4-38068 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Griesche, Axel A1 - Boateng, Francis A1 - Kromm, Arne A1 - Kannengießer, Thomas A1 - Zscherpel, Uwe A1 - Ewert, Uwe T1 - Real-time X-ray Radiography for Hot Crack Detection during Welding N2 - Fast digital radiography was used to observe the crack development during single pass bead-on-plate gas tungsten arc welding with a minifocus X-ray source and a digital detector array with 75-micrometer pixel size. The sample material were 5 mm thick AlMgSi plates. An acquisition rate of 12 frames per second and an exposure time of 40 ms per frame were used for real-time observation of the hot crack propagation during welding. The basic spatial resolution of the images is about 80 µm. A 3D laminographic reconstruction of the acquired 2D radiographic images gives access to the volumetric extent of the cracks in the welded sample. The parallel use of a high-speed camera during welding allows the real-time inspection of surface cracks. The development of surface cracks was compared with the crack’s distribution in the sample volume and these results were correlated to the used welding parameters. T2 - MS&T 2016 CY - Salt Lake City, Utah, USA DA - 23.10.2016 KW - X-ray radiography KW - Welding KW - Hot crack KW - X-ray imaging KW - Laminography PY - 2016 AN - OPUS4-38069 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Imrie, F. A1 - Andersen, I. H. A1 - Jeppesen, C. A1 - Louring, S. A1 - Ortel, Erik A1 - Hodoroaba, Vasile-Dan A1 - Gibson, I. T1 - Biocompatibility of DC magnetron-sputtered TiO2 N2 - SETNanoMetro, a European Seventh Framework project, seeks to develop standard synthetic routes and metrological characterisation methods for the development and production of TiO₂ nanoparticles and nano-sized coatings with highly-defined, homogeneous and reproducible characteristics, including bulk structure, size, shape and surface structure. These materials are being tested for their potential in selected technological applications, including as coatings on bone-substituting prostheses. The objective of this study was to assess how variations in morphology and chemistry of nano-sized TiO₂ coatings affect their biocompatibility in vitro. T2 - Bioceramics 28 CY - Charlotte, NC, USA DA - 18.10.2016 KW - TiO2 KW - Coating KW - Biocompatibility PY - 2016 AN - OPUS4-38077 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rades, Steffi A1 - Ortel, Erik A1 - Wirth, Thomas A1 - Garcia, Sarai A1 - Gomez, Estibaliz A1 - Blanco, Miren A1 - Alberto, Gabriele A1 - Martra, Gianmario A1 - Hodoroaba, Vasile-Dan T1 - Analysis of functionalization of TiO2 nanoparticles and various substrates by means of SEM-EDX, AES and ToF-SIMS N2 - The physico-chemical characteristics of TiO2 coatings can greatly influence their final performance. In SETNanoMetro, different deposition procedures are being set for applying films of TiO2 NPs with defined and homogenous thickness on supports of interest for the applications studied in the project. The selected substrates are the following: (i) Silica glasses for photocatalytic measurements, (ii) Ti-alloys for orthopedic and/or dental prostheses, and for cell cultures, and (iii) Conductive glasses (e.g. Fluorine doped Tin Oxide, FTO) for dye-sensitized solar cells. From the different film deposition procedures studied within the project Self-assembly of TiO2 NPs in multiple layers was selected. For this, surface modification of the substrate and of TiO2 nanoparticles (NPs) with e.g. silane coupling agents is a prerequisite. First attempts to prepare the self-assembled coating on the functionalized glass substrates seem to indicate that the functionalized NPs adhere to the substrates, even if the final coatings were not homogenous and presented agglomerates. ToF-SIMS results support this outcome. In order to use the layer-by-layer deposition technique for the formation of TiO2 films by controlled self-assembly of the TiO2 NPs, the proper complementary moieties for the functionalization of the NPs were chosen. A first set of NPs has been produced by reaction with (3-aminopropyl)phosphonic acid (APPA) in order to functionalize the surface with free amino-groups. Then, the complementary NP set can be obtained from an aliquot of the first one, through the conversion of free surface amino-groups to aldehydes by reaction with glutaraldehyde. A proper approach for the functionalization of two types of TiO2, commercial P25 (Evonik) and SETNanoMetro-sample labelled UT001, with APPA was developed. A second set of NPs consisting of three types of TiO2 NPs, P25 and SETNanoMetro NPs (TiO2 NPs with high specific surface area > 150 m2/g and TiO2 NPs with low size < 20 nm) was functionalized with (3-aminopropyl)triethoxysilane (APTS). As for the previous set of NPs, the complementary NP set was obtained through the conversion of free surface amino-groups to aldehydes by reaction with glutaraldehyde. EDX, AES and ToF-SIMS spectra were collected and analyzed to demonstrate the presence of the surface functionalization of the different types of TiO2 NPs. T2 - Nanoscience meets Metrology - Synthesis, Characterization, Testing and Applications of Validated Nanoparticles - International Summer School CY - Turin, Italy DA - 04.09.2016 KW - Time-of-flight secondary-ion mass spectrometry KW - X-ray spectroscopy KW - Auger electron spectroscopy KW - Electron microscopy KW - Nanoparticles KW - Thin films PY - 2016 UR - http://www.setnanometro.eu/events/ AN - OPUS4-38064 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Griesche, Axel A1 - Dabah, Eitan A1 - Pfretzschner, Beate A1 - Schaupp, Thomas A1 - Kannengießer, Thomas T1 - Imaging of Hydrogen in Steels with Neutrons N2 - Cold neutrons are predominantly scattered at hydrogen when penetrating hydrogen-charged samples, resulting in a high image contrast between hydrogen and e.g. iron. The used radiographic set-ups consist of a neutron source, state-of-the-art scintillator screens and digital cameras. This allows monitoring diffusive hydrogen fluxes two-dimensionally with 20s temporal resolution. Such hydrogen fluxes can be quantified by using standards with known hydrogen content and similar sample thickness. Neutron tomography generates three-dimensional models of the hydrogen distribution in steel. Such models gain new insight for damage analysis by showing the hydrogen accumulations around cracks and by enabling the hydrogen gas pressure estimation inside cracks. The capabilities and limitations, as well as perspectives of this method will be discussed and illustrated with help of selected examples. T2 - MS&T 2016 CY - Salt Lake City, Utah, USA DA - 23.10.2016 KW - Hydrogen embrittlement KW - Neutron imaging KW - Neutron radiography KW - Neutron tomography PY - 2016 AN - OPUS4-38066 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Würth, Christian A1 - Hatami, Soheil A1 - Kaiser, Martin A1 - Pauli, Jutta A1 - Resch-Genger, Ute T1 - Absolute fluorescence measurements > 1000 nm: setup design, calibration and standards N2 - Bright emitters with photoluminescence in the spectral region of 800 – 1600 nm are increasingly important as optical reporters for molecular imaging, sensing, and telecommunication and as active components in electrooptical and photovoltaic devices. Their rational design is directly linked to suitable methods for the characterization of their signal-relevant properties, especially their photoluminescence quantum yield. Aiming at the development of bright semiconductor nanocrystals with emission > 1000 nm, we designed a new NIR/IR integrating sphere setup for the wavelength region of 600 – 1600 nm. We assessed the performance of this setup by acquiring the corrected emission spectra and quantum yield of the organic dyes Itrybe, IR140, and IR26 and several infrared (IR)-emissive Cd1-xHgxTe and PbS semiconductor nanocrystals and comparing them to data obtained with two independently calibrated fluorescence instruments absolutely or relatively to previously evaluated reference dyes. Our results highlight special challenges of photoluminescence studies in the IR ranging from solvent absorption to the lack of spectral and intensity standards together with quantum dot-specific challenges like photobrightening and photodarkening and the size-dependent air stability and photostability of differently sized oleate-capped PbS colloids. These effects can be representative for lead chalcogenides. Moreover, we redetermined the quantum yield of IR26, the most frequently used IR reference dye, to 1.1×10-3 in 1,2-dichloroethane DCE with a thorough sample reabsorption and solvent absorption correction. T2 - SPIE CY - San Francisco, USA DA - 11.02.2016 KW - Ir KW - Quantum yield PY - 2016 AN - OPUS4-38405 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Emmerling, Franziska A1 - Fischer, Franziska A1 - Kulla, Hannes A1 - Wilke, Manuel T1 - In situ analysis of mechanochemical reactions using combined X-ray diffraction and Raman spectroscopy N2 - Mechanochemistry is increasingly used for synthesizing various materials including metal organic compounds and cocrystals. Although this synthesis approach offers a fast and pure synthesis in high yields, there is a lack in understanding the mechanisms of milling reactions. The necessary data can only be obtained in in situ experiments, which were only recently established for milling reactions. Herein, we present a novel setup enabling a combined in situ investigation of mechanochemical reactions using synchrotron XRD and Raman spectroscopy. The specific combination allows to study milling processes comprehensively on the level of the molecular and crystalline structure and thus obtaining reliable data for mechanistic studies. Besides well-known MOFs like ZIF-8, the formation process of new metal phosphonates and model cocrystals could be studied in detail. The syntheses pathway of the different compounds could be revealed. The results prove that the presented method combination is applicable for a wide range of materials and will provide the necessary understanding to tune and optimize mechanochemically synthesized compounds. T2 - 3oth Meeting of the European Crystallographic Association CY - Basel, Switzerland DA - 28.08.2016 KW - Mechanochemistry KW - In situ PY - 2016 AN - OPUS4-38363 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kricheldorf, H. R. A1 - Weidner, Steffen A1 - Scheliga, F. T1 - Cyclization and dispersity of polyesters N2 - Starting out from Flory`s most probable Distribution concept, correct and incorrect evaluations of SEC measurements are discussed. Using the correct mode, polyesters prepared by irreversible and reversible polycondensation methods were studied. Polyesters of α,ω−alkanediols and isophthalic acid or polyesters of diphenols and sebacic acid were prepared by three different irreversible polyconcensation methods. Formation of cyclic oligo and polyesters was monitored by MALDI-TOF mass spectrometry and dispersities were measured by SEC. The results are compared with the theories of Flory and Odian. Eqilibrated polyesters were prepared by reversible polycondensation of ethyl 6-hydroxycaproate or by alcohol-initiated ring-opening polymerization of ε-caprolactone. Various catalysts were compared. The influence of dilution and of di- or multifunctional initiators was evaluated. Furthermore, equilibrated polylactides were prepared from L- or meso-lactide at 120, 160 and 180°C. A fast even-odd equilibration was discovered in addition to reversible cyclization and intermolecular transesterification. The influence of these different equilibration mechanisms on the dispersity was investigated. The preparative and theoretical consequences are discussed. T2 - Polycondensation 2016 CY - Moscow, Russia DA - 11.09.2016 KW - Polyester KW - Cyclization KW - MALDI-TOF MS KW - SEC PY - 2016 AN - OPUS4-38365 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -