TY - CONF A1 - Maiwald, Michael T1 - Quantitative and online NMR Spectroscopy at BAM N2 - Online NMR spectroscopy, Determination of impurities of fluids, NMR process Monitoring, purity assessment T2 - NMR-Kolloquium Buchs CY - Buchs, Switzerland DA - 29.05.2015 KW - qNMR KW - Quantitative NMR-Spektroskopie KW - Online NMR Spectroscopy KW - Reaction monitoring KW - Reference material KW - Metrology PY - 2015 AN - OPUS4-36143 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maiwald, Michael T1 - qNMR forever – reference material metrology at high pressures and high purities N2 - Due to recent advances in technical developments of NMR instruments such as acquisition electronics and probe design, detection limits of components in liquid mixtures were improved into the lower ppm range (approx. 5–10 ppm amount of substance). This showed that modern NMR equipment is also suitable for the observation of hydrocarbon samples in the expanded fluid phase or gas phase. Since Quantitative NMR spectroscopy (qNMR) is a direct ratio method of analysis without the need of calibration it was used to determine impurities in appropriate liquid and liquefied hydrocarbon isomers up to C6, which are used for preparation of primary gas standards, e.g., natural gas or exhaust gas standards. At the same time it is possible to yield structural information with a minimum of sample preparation. Thus, cross contaminations between different isomers of the observed hydrocarbons and their (NMR-active) impurities can be identified and quantified. In general, most quantitative organic chemical measurements rely on the availability of highly purified compounds to act as calibration standards. The traceability and providence of these standards is an essential component of any measurement uncertainty budget and provides the final link of the result to the units of measurement, ideally the SI. The more recent increase in the use of qNMR for the direct assessment of chemical purity however can potentially improve the traceability and reduce the uncertainty of the measured chemical purity at a reduced cost and with less material. For example the method has beneficially been used by National Measurement institutes for recent CCQM comparisons including the CCQM–K55 series of purity studies. Traditional ‘indirect’ methods of purity analysis require that all impurities are identified and quantified, leading to a minimum of 4 individual analytical methods (organic impurities, water, solvents, inorganic residue). These multiple technique approaches measure an array of different chemical impurities normally present in purified organic chemical compounds. As many analytical methodologies have compound-specific response factors, the accuracy and traceability of the purity assessment is dependent on the availability of reference materials of the impurities being available. qNMR provides the most universally applicable form of direct purity determination without need for reference materials of impurities or the calculation of response factors but only exhibiting suitable NMR properties. The development of CRMs addressing qNMR specific measurement issues will give analysts compounds ideally suited for the analytical method and also provide full characterisation of qNMR related parameters to enable more realistic uncertainty budgets. These materials will give users the tools to exploit qNMR more easily and enable them to speed up analytical method development and reduce the time and financial burden of multiple analytical testing. T2 - 3rd Practical Application of NMR in Industry Conference (PANIC) 2015 CY - La Jolla, CA, USA DA - 09.02.2015 KW - qNMR KW - Quantitative NMR-Spektroskopie KW - Reference Material KW - Metrology PY - 2015 AN - OPUS4-36144 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maiwald, Michael A1 - Meyer, Klas A1 - Zientek, Nicolai T1 - Towards online reaction monitoring with fully automated NMR data evaluation and modelling - Current results from simultaneous 19F-1H medium resolution NMR experiments N2 - NMR Process Monitoring Towards an automated field integration T2 - 3rd Practical Applications of NMR in Industry Conference (PANIC) - Mestrelab users' meeting CY - La Jolla, CA, USA DA - 08.02.2015 KW - Online NMR spectroscopy KW - Reaction monitoring KW - Prozessanalytik KW - Process analytical technology PY - 2015 AN - OPUS4-36145 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maiwald, Michael T1 - Innovationen in der Prozessanalytik – Welches sind die neuen Herausforderungen? N2 - Der Vortrag stellt die aktuellen Forschungsschwerpunkte zum Thema Prozessanalytik an der Bundesanstalt für Materialforschung und -prüfung (BAM) vor und nennt aktuelle Entwicklungsfelder mit dem Ziel gemeinsamer F&E-Projekte. Zunächst wird die Prozessindustrie und ihre Wertschöpfungskette vorgestellt. Daraus ergibt sich eine Motivation für Prozessanalytik. Zwischen der Prozessanalytik in der Pharmazeutische Industrie und der Chemischen Industrie bzw. Verfahrenstechnik gibt es Unterschiede, die herausgearbeitet werden. Der Vortrag schließt mit Technologiewünschen und Technologievisionen und nennt Konkrete Beispiele für Visionen für PAT, insbesondere im Kontext des Zukunftsprojekts „Industrie 4.0“ T2 - Innovationen entwickeln – Von der Idee bis zum Projektstart CY - Göttingen, Germany DA - 11.12.2014 KW - Prozessanalytik KW - Prozessindustrie KW - Innovationen KW - Pharmazeutische Industrie KW - Technologiewünsche KW - Technologievisionen KW - Industrie 4.0 PY - 2014 AN - OPUS4-36146 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Guthausen, G. T1 - Online measurements in a bypass: challenges and possibilities N2 - The design of sample flow cells, commonly used in online analytics and especially for medium resolution NMR spectroscopy (MR-NMR) in low magnetic fields, was experimentally and theoretically investigated by 1H-NMR and numerical simulations. The flow pattern was characterised to gain information about the residence time distribution and mixing effects. Both 1H-NMR imaging and spectroscopy were used to determine the characteristics of flow cells and their significance for on-line measurements such as reaction monitoring or hyphenated separation spectroscopy. The volume flow rates investigated were in the range from 0.1 to 10 ml/min, typically applied in the above mentioned applications. When compared to those commonly used in high-field NMR, the special characteristics of flow cells for MR-NMR were revealed by various NMR experiments and compared with CFD simulations. The influence of the design of the inlet and outlet on the flow pattern was investigated as well as the effect of the length of the cell. For practical use, a numerical estimation of the inflow length was given. In addition, it was shown how experiments on the polarisation build-up revealed insight into the flow characteristics in MR-NMR. T2 - Quantitative NMR Methods for Reaction and Process Monitoring (NMRPM) Symposium CY - Kaiserslautern, Germany DA - 15.01.2015 KW - Online NMR spectroscopy KW - Process analytical technology KW - Flow profiles KW - Online monitoring KW - Reaction monitoring PY - 2015 AN - OPUS4-36147 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zientek, Nicolai T1 - Automated data evaluation and modeling of simultaneous 19F-1H medium resolution NMR spectra for online reaction monitoring N2 - The development of innovative medium resolution NMR spectrometers (MR-NMR) is remarkable due to their possible applications in quality control, education, or process monitoring. The use of compact permanent magnets allows to employ NMR devices in an industrial environment without high maintenance requirements and without the need for cryogenic liquids. A benchtop 43 MHz MR-NMR spectrometer was used for reaction monitoring. Quasi-simultaneous proton and fluorine NMR spectra were acquired. Automatic data pretreatment and evaluation methods were applied and compared to quantitative 500 MHz HR-NMR spectroscopy T2 - Quantitative NMR Methods for Reaction and Process Monitoring (NMRPM) Symposium CY - Kaiserslautern, Germany DA - 15.01.2015 KW - Online NMR Spectroscopy KW - 1H-NMR KW - 19F-NMR KW - Reaction Monitoring KW - Benchtop NMR Spectroscopy KW - Process Analytical Technology PY - 2015 AN - OPUS4-36148 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Jakubowski, Norbert T1 - Book review: Freddy Adams and Carlo Barbante - Chemical imaging analysis N2 - In this book many practical hints are given and analytical problems are discussed by the authors from their own experiences. A critical assessment of the methods is given, which is most important for decision makers to select a good combination of complementary methods to solve practical analytical problems. KW - Chemical imaging analysis KW - Surface analysis KW - Interface analysis PY - 2016 DO - https://doi.org/10.1007/s00216-016-9517-9 SN - 1618-2642 SN - 1618-2650 VL - 408 IS - 16 SP - 4199 EP - 4201 PB - Springer AN - OPUS4-36216 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Dietrich, Paul A1 - Nietzold, Carolin A1 - Weise, Matthias A1 - Unger, Wolfgang A1 - Alnabulsi, Saad A1 - Moulder, John T1 - XPS depth profiling of an ultrathin bioorganic film with an argon gas cluster ion beam N2 - The growing interest in artificial bioorganic Interfaces as a platform for applications in emerging Areas as personalized medicine, clinical diagnostics, biosensing, biofilms, prevention of biofouling, and other fields of bioengineering is the origin of a need for in Detail multitechnique characterizations of such layers and interfaces. The in-depth analysis of biointerfaces is of special interest as the properties of functional bioorganic coatings can be dramatically affected by in-depth variations of composition. In worst cases, the functionality of a device produced using such coatings can be substantially reduced or even fully lost. KW - XPS KW - Ar gas cluster gun KW - Depth profiling KW - Bioorganic film PY - 2016 UR - http://scitation.aip.org/content/avs/journal/bip/11/2/10.1116/1.4948341 DO - https://doi.org/10.1116/1.4948341 SN - 1934-8630 VL - 11 IS - 2 SP - 029603-1 EP - 029603-5 PB - American Vacuum Society CY - New York AN - OPUS4-36218 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gemeinert, Marion T1 - Stability assessment of ceramic high dielectric N2 - Resolution of capacitive sensors can be improved enormously by replacement of the dielectric material between the capacitor plates (e.g. air-dielectric) by a dielectric fluid with high permittivity. High dielectric liquid dispersions of ceramic micro and nano powders should be qualified as dielectric fluid with longtime shelf life. For this purpose it was necessary to produce stabilized ceramic suspensions with high particle concentration and to investigate sedimentation processes of the particles. Characterization of particles was done by use of zeta potential measurement, gas adsorption measurements (BET), density measurement with gas pycnometer as well as particle sizing by ultrasound spectroscopy and by use of an optical centrifuge. Shelf life of optimized electrostatic and steric stabilized ceramic suspension was investigated by use of an optical centrifuge, a LUMISizer 651 MW (LUM Ltd.) with STEP technology and front tracking analysis. Two different wave lengths – NIR (865 nm) and blue light (470 nm) were available for examination. Centrifugation measurements with different rotation speed were used to study the rheological behavior and the sedimentation process. By this way it was possible to achieve accelerated stability determination. Measured values could be used to simulate the sedimentation process under gravity acceleration and to predict shelf life for suspensions with different dispersants. T2 - PARTEC 2016 CY - Nürnberg, Germany DA - 19.04.2016 KW - Ceramic dispersion KW - Stability assessment KW - Analytical centrifuge KW - Shelf life prediction PY - 2016 AN - OPUS4-36184 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Scharlach, C. A1 - Müller, Larissa A1 - Wagner, S. A1 - Kobayashi, Y. A1 - Kratz, H. A1 - Ebert, M. A1 - Jakubowski, Norbert A1 - Schellenberger, E. T1 - LA-ICP-MS allows quantitative microscopy of europium-doped iron oxide nanoparticles and is a possible alternative to ambiguous Prussian blue iron staining N2 - The development of iron oxide nanoparticles for biomedical applications requires accurate histological evaluation. Prussian blue iron staining is widely used but may be unspecific when tissues contain substantial endogenous iron. Here we tested whether microscopy by laser ablation coupled to inductively coupled plasma mass spectrometry (LA-ICP-MS) is sensitive enough to analyze accumulation of very small iron oxide particles (VSOP) doped with europium in tissue sections. KW - Atherosclerotic plaques KW - LA-ICP-MS microscopy KW - Quantification KW - Element microscopy KW - Histology PY - 2016 DO - https://doi.org/10.1166/jbn.2016.2230 SN - 1550-7033 SN - 1550-7041 VL - 12 IS - 5 SP - 1001 EP - 1010 AN - OPUS4-36189 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -