TY - CONF A1 - Mishurova, Tatiana T1 - 3D imaging and residual stress analysis of AM materials at BAM N2 - The overview of the activity of group 8.5 Micro-NDT (BAM, Belin, Germany) in the field of additively manufacturing material characterization will be presented. The research of our group is focused on the 3D imaging of AM materials by means of X-ray Computed Tomography at the lab and at synchrotron, and the residual stress characterization by diffraction (nondestructive technique). T2 - Seminar at Chalmers University and Centre for Additive Manufacture (CAM2) CY - Gothenburg, Sweden DA - 19.05.2022 KW - Additive manufacturing KW - Laser powder bed fusion KW - Residual stress KW - Computed tomography KW - Synchrotron X-ray diffraction KW - X-ray refraction PY - 2022 AN - OPUS4-55019 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mishurova, Tatiana T1 - 3D Imaging and residual stress analysis of additively manufactured materials N2 - The focus of the presentation focus will be on 3D imaging by means of X-ray Computed Tomography (XCT) at the lab and at synchrotron, and the non-destructive residual stress (RS) characterization by diffraction of additively manufactured (AM) materials in BAM (Berlin, Germany). The manufacturing defects and high RS are inherent of AM techniques and affect structural integrity of the components. Using XCT the defects size and shape distribution as well as geometrical deviations can be characterized, allowing the further optimization of the manufacturing process. Diffraction-based RS analysis methods using neutron and synchrotron X-rays at large scale facilities offer the possibility to non-destructively spatially resolve both surface and bulk RS in complex components and track their changes following applied thermal or mechanical loads. T2 - The International Symposium on Nondestructive Characterization of Materials 2023 CY - Zurich, Switzerland DA - 15.08.2023 KW - Additive manufacturing KW - Residual stress KW - X-ray computed tomography PY - 2023 AN - OPUS4-58113 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mishurova, Tatiana T1 - Applications of x-ray computed tomography in material science N2 - The overview of the activity of Federal Institute for Material Research and Testing (BAM, Belin, Germany) in the field material characterization by X-ray imaging is presented. The principle of X-ray Computed Tomography (XCT) is explained. The multiple examples of application of quantitative analysis by XCT are reported, such as additive manufacturing, Li-ion battery, concrete research. T2 - Lecture for PhD students at Politecnico di Torino CY - Turin, Italy DA - 14.03.2024 KW - X-ray computed tomography KW - Additive manufacturing PY - 2024 AN - OPUS4-59689 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rethmeier, Michael A1 - Artinov, Antoni A1 - Meng, Xiangmeng A1 - Bakir, Nasim A1 - Üstündag, Ömer A1 - Bachmann, Marcel A1 - Gumenyuk, Andrey T1 - The bulging effect and its relevance in high power laser beam welding N2 - The present work deals with the recently confirmed widening of the weld pool interface, known as a bulging effect, and its relevance in high power laser beam welding. A combined experimental and numerical approach is utilized to study the influence of the bulge on the hot cracking formation and the transport of alloying elements in the molten pool. A technique using a quartz glass, a direct-diode laser illumination, a high-speed camera, and two thermal imaging cameras is applied to visualize the weld pool geometry in the longitudinal section. The study examines the relevance of the bulging effect on both, partial and complete penetration, as well as for different sheet thicknesses ranging from 8 mm to 25 mm. The numerical analysis shows that the formation of a bulge region is highly dependent on the penetration depth and occurs above 10 mm penetration depth. The location of the bulge correlates strongly with the cracking location. The obtained experimental and numerical results reveal that the bulging effect increases the hot cracking susceptibility and limits the transfer of alloying elements from the top of the weld pool to the weld root. T2 - 1st Annual Assembly and Conference of The Welding Federation of Africa (TWF-Africa) CY - Cairo, Egypt DA - 14.03.2023 KW - Laser beam welding KW - Melt pool dinamics PY - 2023 AN - OPUS4-58695 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mishurova, Tatiana T1 - In-situ hot isostatic pressing combined with x-ray imaging and diffraction of laser powder bed fusion ti-6al-4v N2 - Hot Isostatic Pressing (HIP) is often introduced to tackle the porosity issue in additively manufactured (AM) materials. For instance, HIP post-processing is recommended to improve fatigue resistance of Laser powder bed fusion (PBF-LB) manufactured parts [1, 2]. Even though HIP cannot completely remove porosity, it significantly decreases the defect population and its average size below the critical threshold value leading to early crack initiation. In the present study, in-situ investigation of HIP procedure of PBF-LB Ti-6Al-4V parts was carried out to gain further insights into the densification mechanism occurring during HIP. The in-situ observations at high pressure and high temperature are uniquely possible at the PSICHE beamline of the Soleil synchrotron (France), thanks to the Ultrafast Tomography on a Paris-Edinburgh Cell (UToPEC) and the combination of the fast phase-contrast tomography and energy-dispersive diffraction [3, 4]. A detailed methodology was developed to ensure that the correct pressure and temperature were maintained during the experiments. The results allowed an estimation of the global dentification rate during HIP of PBF-LB Ti-Al-4V material, as well as a detailed quantitative characterization of the influence of pore size and shape on the densification process, thereby understanding the effectiveness of HIP process on different pore categories. After 20 mins, 75% of porosity can be considered as closed or has size below the resolution of the XCT reconstruction. We also observed that the smallest defects showed higher densification rate, while the defect shape did not have significant effect on such rate. The current development of in-situ HIP experiment allows experimental quantification and validation of the simulation work. Ultimately it paves the road to tailoring the HIP procedure for different materials depending on the porosity and microstructure. T2 - AAMS 2023 CY - Madrid, Spain DA - 26.09.23 KW - Additive manufacturing KW - HIP KW - X-ray computed tomography PY - 2023 AN - OPUS4-58482 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mishurova, Tatiana T1 - 3D imaging and residual stress analysis for AM Materials N2 - The overview of the activity of Federal Institute for Material Research and Testing (BAM, Belin, Germany) in the field of additively manufacturing material characterization will be presented. The research of our group is focused on the 3D imaging of AM materials by means of X-ray Computed Tomography at the lab and at synchrotron, and the residual stress characterization by diffraction (nondestructive technique). T2 - Seminar at Integrated Additive Manufacturing center, Politecnico Torino CY - Turin, Italy DA - 14.02.2023 KW - Additive manufacturing KW - Laser powder bed fusion KW - Residual stress KW - Computed tomography KW - Synchrotron X-ray diffraction PY - 2023 AN - OPUS4-57047 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tang, Chi-Long T1 - UFP-Emission beim 3D-Druck N2 - Desktop-3D-Drucker haben in der letzten Dekade große Popularität in Bildungseinrichtungen, kleinen Unternehmen und Privathaushalten erlangt. Weit verbreitet ist mittlerweile die „Fused Filament Fabrication (FFF)“ Technologie. Hier wird ein thermoplastisches Filament geschmolzen, durch eine Metalldüse extrudiert und anschließend schichtweise so auf ein Druckbett aufgetragen, dass ein 3D-Objekt entsteht. Das Filamentmaterial wird dabei thermisch stark belastet, was zur Emission von Aerosolen sowie flüchtigen organischen Verbindungen (VOC) führt. Dabei werden hauptsächlich ultrafeine Partikel (UFP, dP < 100 nm) freigesetzt werden, die sogar in manchen Fällen im sub-4nm Größenbereich einen signifikanten Anteil ausmachen können (Tang und Seeger 2024). Die gesundheitliche Relevanz eingeatmeter UFP ist durch sehr viele Studien gut belegt. Während eines i.d.R. mehrstündigen FFF-Druckvorgangs wird ein Anwender mit diesen Luftschadstoffen im Innenraum exponiert, häufig ohne eine Einschätzung des damit verbundenen Risikos zu haben. Die Exposition kann durch technische Faktoren (z.B. Druckerausstattung und -einstellung, Innenraumventilation), aber auch erheblich durch die Filamentauswahl beeinflusst werden. Unser Vorschlag zur Risikominderung besteht in der Auszeichnung emissionsarmer Filamentprodukte mit dem Umweltzeichen „Blauer Engel“, um so den Verbrauchern eine fundierte Auswahl zu ermöglichen. In unserem Projekt entwickeln wir dafür ein kammerbasiertes, standardisierbares und robustes Prüfverfahren zur vergleichenden Messung der Emission aus Filamenten. Mit dem Strangdruck-Verfahren (engl. Strand Printing Method, SPM) wird eine festgelegte Filamentlänge mit konstanter Rate extrudiert und auf dem Druckbett abgelegt, ohne dabei ein 3D-Objekt aufzubauen. Diese Vorgehensweise reduziert den Einfluss experimentell schlecht zu kontrollierender Faktoren sowie die Ausfallquote. Eine detaillierte Beschreibung und die Vorteile von SPM werden in Tang und Seeger (2022) erläutert. SPM wurde bereits für 44 Filamentprodukte aus unterschiedlichen Polymeren und Additiven als Vergleichstest angewendet. Alle Messungen wurden in einer klimatisierten 1 m³-Emissionsprüfkammer durchgeführt. Die Gesamtanzahl der emittierten Partikel (TP) dient als Beurteilungsmaß, in Anlehnung an die Vergabegrundlage DE-UZ-219 des Umweltzeichens Blauer Engel für Laserdrucker. Unter den getesteten Filamentprodukten variiert TP um ca. vier Größenordnungen (1E+9 ≤ TP ≤ 1E+13). Auch innerhalb jeder der untersuchten Polymergruppen variierte TP signifikant. Die Partikelemission kann daher nicht allein nach dem Basispolymer kategorisiert werden. Unsere Resultate belegen, dass die Stärke der Partikelemission eher eine charakteristische und individuelle Eigenschaft eines Filamentproduktes ist. Die Herkunft der Polymere, die herstellerspezifischen Additive sowie die nicht deklarierte Verunreinigungen können einen starken Einfluss auf die Emission haben. Die Auszeichnung von emissionsarmen Filament-produkten verspricht somit eine einfache, aber effektive Maßnahme zu sein, um Verbrauchern eine Minderung des Expositionsrisikos beim FFF-3D-Druck zu ermöglichen. T2 - 5. Symposium "Ultrafeinstaub in der Atmosphäre und in Innenräumen" CY - Berlin, Germany DA - 16.09.2024 KW - 3D-Druck KW - Ultrafeine Partikel KW - Innenraumemission KW - Luftschadstoffe KW - Emissionsprüfung PY - 2024 AN - OPUS4-61067 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hilgenberg, Kai T1 - Herausforderungen in der additiven Fertigung sicherheitsrelevanter Komponenten N2 - Der Vortrag stellt nach einer kurzen allgemeinen Einleitung zur additiven Fertigung und des Laser Powder Bed Fusion Verfahrens einige Herausforderungen vor, die derzeitig den Einsatz von AM-Komponenten in sicherheitsrelevanten Anwendungen erschweren. Abschließend werden zwei Beispiele von Arbeiten der BAM gezeigt, die zur Überwindung dieser Herausforderungen beitragen können. T2 - Anwendertreffen des Laserverbundes Berlin-Brandenburg CY - Berlin, Germany DA - 25.11.2022 KW - Additive Fertigung KW - Laser Powder Bed Fusion PY - 2022 AN - OPUS4-56435 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Madia, Mauro T1 - Fatigue Strength of Aerospace Parts Repaired by Cold Spray N2 - Aerospace components are safety critical parts, which are often replaced when found defective after the fabrication process or after periodic inspection in-service. Cold spray repair is a promising and cost-saving alternative to replacing worn parts. Depositing materials in decent quality fill machined damage volumes can enhance the performance of refurbished parts and extend their working life. Furthermore, repair represents a resource-efficient and green process in a world targeting at decarbonization of many industrial sectors. Component repair consists of a defined sequence of operations. First, damage is removed by machining, then new material is applied by cold spray on the machined substrate. Usually, the original functional shape of the component is restored by machining. Post-spraying heat treatments can be applied where required. Despite the advantages, cold spray repair still suffers from major limitations which prevent its application in safety relevant parts. The main challenges are posed by the poor adhesion strength, the porosity inherent in the manufacturing process, the reduced ductility and the presence of residual stresses. This work presents recent results obtained in the frame of the cluster project CORE devoted to the development of automatized repair of aerospace parts by cold spray. The investigations consider high-strength aluminum alloys typically used in structural applications in the aerospace industry. As the fatigue properties are crucial to the safe application of repaired components, and given the presence of process-induced defects, a damage tolerant framework is peculiarly suitable for the structural integrity assessment of repaired commponents and give an indication of the permissible defects to optimize the parameters of the cold spray process. Several high cycle fatigue and fatigue crack propagation tests have been performed to compare the fatigue performance of base and repaired materials. The mechanical tests are corroborated by fractographic and microstructural investigations. T2 - ICAM2024 CY - Atlanta, GA, USA DA - 28.10.2024 KW - Cold Spray KW - Aerospace KW - Repair KW - Structural Integrity KW - Fatigue Strength PY - 2024 AN - OPUS4-61539 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hilgenberg, Kai T1 - EOS M300 as the heart of the QI living lab: Advancing with digital process chains N2 - This presentation shows how the connectivity of the EOS-M300/4 laser powder bed system is used to capture machine and process data as part of the living lab in QI Digital and how this can enable future digital quality assurance in additive manufacturing. T2 - AM Forum 2025 CY - Berlin, Germany DA - 17.03.2025 KW - Additive manufacturing KW - Quality assurance KW - QI Digital KW - Living lab PY - 2025 AN - OPUS4-62740 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -