TY - CONF A1 - Ulbricht, Alexander T1 - Tales from Within: Residual Stress and Void Formation in LPBF 316L N2 - An unusual microstructure, inherent residual stresses and void formation are the three key aspects to control when assessing metallic parts made by LPBF. This talk explains an experiment to unravel the interlinked influence of the two mechanisms for the formation of residual stresses in LPBF: the temperature gradient mechanism and constricted solidification shrinkage. The impact of each mechanism on the shape and magnitudes of the residual stress distribution is described. Combined results from neutron diffraction, X-ray diffraction, computed tomography and in-situ thermography are presented. Also, influence of scan strategies as well as surface roughness of subjacent layers on void formation is shown. Results from computed tomography and in-situ thermography of a specimen dedicated to study the interaction of the melt pool with layers of powder underneath the currently illuminated surface are presented. T2 - 2nd Workshop on In-situ Monitoring and Microstructure Development in Additive Manufacturing CY - Online meeting DA - 19.04.2021 KW - Neutron diffraction KW - Laser powder bed fusion KW - In-situ thermography KW - Computed tomography KW - X-ray diffraction KW - Residual stress KW - Pore formation KW - AISI 316L PY - 2021 AN - OPUS4-52819 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simón Muzás, Juan T1 - Weldability of PBF-LB/M Inconel 718 lattice structures by laser beam N2 - The present research focuses on the weldability of PBF-LB/M lattice structure parts of Inconel 718 by means of laser beam welding. The integration of complex and lightweight AM structures into assemblies employing conventional joining methods is challenging. During the welding process, dissipation of the laser heat input through thin-walled structures of these lightweight structures is strongly limited, resulting in heat accumulation, atypical cooling rates, and affecting weld geometry, quality of the joint and microstructure. PBF-LB/M parts have been manufactured in three characteristic build directions. They were all stress relieved, then a group of them were submitted to an additional solution annealing and the second group to a two-step aging treatment. Afterwards, these parts were welded to identical PBF-LB/M parts and to wrought ones in butt position. To gain insight into the welding temperature field and to explain segregation mechanisms, grain growth and asymmetries, thermocouples have been attached on the surface’s regions and struts nearby. Joining a lattice structure with a full material wrought sample results in clear asymmetric welds due to dissimilar heat dissipation on both sides of the seam. Selected pre-weld heat treatments have a crucial influence on the quality of the seam on the AM part. T2 - International Institute of Welding IIW 2023 Conference CY - Singapore DA - 16.07.2023 KW - Additive manufacturing (AM) KW - Laser-based powder bed fusion of metal (PBF-LB/M) KW - Laser beam welding KW - Lattice structure KW - Hybrid part KW - Heat treatment KW - Inconel 718 PY - 2023 AN - OPUS4-58017 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simón Muzás, Juan A1 - Brunner-Schwer, Christian A1 - Hilgenberg, Kai A1 - Rethmeier, Michael T1 - Mechanical properties of laser welded joints of wrought and heat treated PBF LB/M Inconel 718 parts depending on build direction N2 - Laser-based Powder Bed Fusion of Metal (PBF-LB/M) is a broadly used metal additive manufacturing (AM) method for fabricating complex metallic parts, whose sizes are however limited by the build envelope of PBF-LB/M machines. Laser welding arises as a valid joining method for effectively integrating these AM parts into larger assemblies. PBF-LB/M components must usually be stress-relieved before they can be separated from the build plate. An additional heat treatment can be beneficial for obtaining homogeneous mechanical properties across the seam or for the formation of desired precipitations in nickel-based-alloys. Therefore, the tensile performance of laser welded hybrid (AM/wrought) and AM-AM tensile samples of Inconel 718 is examined after undergoing three different heat treatments and considering three relevant build directions. It can be shown that the build orientation is an influencing factor on weld properties even after two applied heat treatments. T2 - Lasers in Manufacturing LiM 2023 CY - Munich, Germany DA - 26.09.2023 KW - Inconel 718 KW - Laser welding KW - PBF/LB-M KW - Hybrid components KW - Heat treatments KW - Build direction KW - Tensile performance PY - 2023 SP - 1 EP - 10 PB - Proceedings Lasers in Manufacturing 2023 CY - München AN - OPUS4-58394 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simón Muzás, Juan T1 - Mitigation of liquation cracking in laser welding of pairs of L-PBF processed and wrought plates of Inconel 718 N2 - Laser welding is an appropriate technique for joining Laser Powder Bed Fusion (L-PBF) parts together and to conventional wrought ones. The potential consists of profiting from synergies between additive and conventional manufacturing methods and overcoming the existing limitations of both. On the one hand, L-PBF is a widely spread metal-based additive manufacturing technique suitable for generating complex parts which can present intrinsic designed cavities, conformal cooling channels, and filigree structures contributing to sustainable manufacturing and efficiency-oriented designs. On the other hand, chamber sizes for producing L-PBF parts are limited, and the process is time-consuming. Thus, its employment is not for every geometry justified. Additionally, they are in most cases individual elements of a larger assembly and need to be joined together to conventionally fabricated parts. The present research suggests laser welding parameters to adequately bond pairs of wrought and L-PBF processed plates and two L-PBF plates of Inconel 718 in butt position. L-PBF samples are printed in three different build-up orientations. Additionally, the influence of as-built L-PBF roughness qualities and usual pre-weld preparations such as edge milling are examined. The effect of normed pre-weld heat treatments is also contemplated. Identified cracks are analyzed by means of EDS in order to confirm the present phases on the areas of interest. EBSD is also employed to obtain a clear depiction of the crystallographic texture and distribution of the hot cracks. The quality of the weldment was examined according to existing standards. Substantial differences in seam geometry and microstructure across different edge’s surface qualities and build directions of stress relieved L-PBF parts have not been detected. Nevertheless, even if no other irregularities are present in the seam, variability in liquation cracking susceptibility has been confirmed. This defect is prone to happen when parts made of this nickel-based superalloy are welded together when not enough precautions are taken. It has been determined that grain size and ductility of the material before welding play a crucial role and mitigating or intensifying these imperfections. Moreover, recommendations are presented to avoid this potential welding defect. T2 - International Welding Conference CY - Tokyo, Japan DA - 17.07.2022 KW - Hybrid Part KW - Liquation Cracking KW - Build-up Orientation KW - Pre-weld Preparation KW - Heat Treatment KW - Selective Laser Melting (SLM) KW - Inconel 718 KW - Laser Powder Bed Fusion (L-PBF) KW - Laser Welding (LW) PY - 2022 AN - OPUS4-55515 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Poka, Konstantin A1 - Ali, Sozol A1 - Ulbricht, Alexander A1 - Schröder, Jakob A1 - Khambayat, Jiganesh A1 - Scholz, Maik A1 - Saeed, Waleed A1 - Merz, Benjamin A1 - Epperlein, Martin A1 - Hilgenberg, Kai T1 - Reduction of extraneous variance in powder bed fusion with laser beam of metals by means of advanced digital preprocessing N2 - Data-driven quality assurance and reproducibility are critical for advancing the industrial maturity of Powder Bed Fusion with Laser Beam of Metals (PBF-LB/M). This study addresses the extraneous variance in scan vectors that arises even for identical cross sections of nominally identical components but located at different positions on the build platform. This inherent variance, common across most PBF-LB/M machines, is caused by scan vector computation relative to the machine coordinate origin and subsequent projection of the resulting pattern onto individual component cross sections. In this work, scan vectors are computed still following conventional slicing, but relative to the workpiece origin of each component, using an EOS M 300-4. This digital preprocessing approach homogenizes fabrication conditions, ensuring that anomalies, such as scan vector overlaps, occur consistently across identical components. The impact during fabrication is assessed through powder bed imaging, melt pool monitoring, and operational data from the multilaser PBF-LB/M machine. Components are manufactured from AlSi10Mg for each scan vector computation origin and subsequently qualified using x-ray computed tomography, optical coordinate measurement, and optical surface measurement. A comprehensive evaluation is conducted, comparing the results in terms of component density, geometric accuracy, and surface roughness to those obtained using conventional preprocessing. Based on these findings, practical recommendations are provided, focusing on achieved quality criteria to identify potential drawbacks, while also considering the life cycle analysis of fabrication. Finally, the study emphasizes the significance of consistent scan vector provisioning for identical components placed at different build platform positions, assuming no roll or pitch during nesting. T2 - ICALEO CY - Orlando, FL, USA DA - 13.10.2025 KW - Quality assurance KW - Data management KW - 3D printing KW - Laser fabrication KW - Life cycle analysis PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-642104 DO - https://doi.org/10.2351/7.0001890 SN - 1042-346X VL - 37 IS - 4 SP - 1 EP - 14 PB - American Institute of Physics Publishing CY - New York AN - OPUS4-64210 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hilgenberg, Kai T1 - Redesign, Repair, Recycle: R-Strategien bei der additiven Fertigung N2 - Der Vortrag stellt ausgewählte Beispiele aus Projekten des Kompetenzzentrums AM@BAM vor, die das Potenzial der additiven Fertigung bei der Umsetzung von R-Strategien im Kontext der Kreislaufwirtschaft aufzeigen. PBF-LB/M kann genutzt werden für ein Redesign von Komponenten mit dem Ziel der Gewicht- und Materialeinsparung. Das gleiche Verfahren wie auch DED-ARC und das Kaltgasspritzen können für die Reparatur anspruchsvoller Legierungen oder Geometrien genutzt werden. Das Thema Recycling wird am Beispiel der Wiedernutzung von Pulver aus dem PBF-LB/M-Prozess adressiert. T2 - DVM-Tagung: Strukturfestigkeit und Produktlebenszyklus – Vom Design bis zur Kreislaufwirtschaft CY - Berlin, Germany DA - 07.10.2025 KW - Additive Fertigung KW - R-Strategien KW - Repair KW - Reparatur PY - 2025 AN - OPUS4-64324 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Raute, Julius A1 - Schmidt, Jonathan A1 - Jokisch, Torsten A1 - Biegler, Max A1 - Rethmeier, Michael T1 - Prozessführung und erreichbare Nahtqualitäten: Elektronenstrahlschweißen von additiv gefertigtem Inconel 939 N2 - Additive Fertigungstechnologien wie das Laser-Pulverbett-Verfahren bieten großes Potenzial für die Fertigung von Neu und Ersatzteilen für stationäre Gasturbinen aus Nickelsuperlegierungen wie Inconel 939 (IN939). Um die Integration in bestehende Baugruppen zu ermöglichen und Bauraumbeschränkungen zu überwinden, muss die Prozesskette der additiven Fertigung um geeignete Fügetechniken erweitert werden. Die vorliegende Arbeit beschäftigt sich daher mit dem Schweißen von Inconel 939. Hierbei werden Bleche aus Gussmaterial und der additiven Herstellung mittels Laser im Pulverbett beim Elektronenstrahlschweißen verglichen. Im Fokus der Untersuchung stehen die erreichbare Nahtqualität im Hinblick auf geometrische Unregelmäßigkeiten sowie innere Defekte in Form von Mikrorissen in der Wärmeeinflusszone. Bei der Auswertung der geschweißten Proben zeigen sich keine Unterschiede in der Ausbildung der Nahtform zwischen dem additiv gefertigten Material und dem Gusswerkstoff. Für beide Materialien ließ sich bei hohen Vorschubgeschwindigkeiten von 20 mm/s die höchste Bewertungsgruppe für Strahlgeschweißte Nähte nach DIN EN ISO 13919-1 erreichen. Unabhängig von der Herstellungsart zeigen beide Materialien eine Zunahme der Rissneigung mit steigendem Vorschub. Das Material aus der additiven Herstellung weist aufgrund seiner Mikrostruktur insgesamt jedoch deutlich weniger Mikrorisse auf, was Potenzial für die Anwendung in der Praxis eröffnet. KW - Elektronenstrahlschweißen KW - PBF-LB/M KW - Inconell939 PY - 2025 UR - https://www.schweissenundschneiden.de/artikel/prozessfuehrung-und-erreichbare-naht-qualitaeten-elektronenstrahlschweissen-von-additiv-gefertigtem-inconel-939 DO - https://doi.org/10.53192/SUS202510 VL - 77 IS - 10 SP - 2 EP - 8 PB - DVS Media Verlag CY - Eltville am Rhein, Deutschland AN - OPUS4-64300 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mohr, Gunther T1 - Comparability issues of test specimens in laser powder bed fusion - how to consider differences in thermal history of complex components and primitive test specimens N2 - The capability to produce complexly and individually shaped metallic parts is one of the main advantages of the laser powder bed fusion (PBF-LB/M) process. However, the thermal history during additive manufacturing of complex components can differ significantly from the thermal history of geometrically primitive test specimens. This can result in divergent microstructures and resulting mechanical properties. It drastically limits the comparability of different built parts and requires expensive full component testing. Moreover, the thermal history as the spatiotemporal temperature distribution has been identified as a major cause for flaw formation. Therefore, it can be hypothesized that a similar thermal history between components and test specimens enhances their comparability. In this talk, the concept of representative test specimens is introduced, which enables the transfer of thermal histories from complex geometries to simple geometries, which can lead to better comparability of material properties. T2 - 4th Asia-Pacific International Conference on Additive Manufacturing (APICAM) CY - Melbourne, Australia DA - 30.06.2025 KW - Additive Manufacturing PY - 2025 AN - OPUS4-64527 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Epperlein, Martin T1 - Digitale Werkzeuge für eine datengetriebene Qualitätssicherung N2 - Der Vortrag stellt die in QI-Digital entwickelten und geplanten Werkzeuge einer digitalen Qualitätsinfrastruktur für die Additive Fertigung vor. Thematisiert werden u.a. die Verwaltungsschale und genormte Datenstrukturen im Kontext der Additiven Fertigung. Im Fokus steht hier die datengetriebene Qualitätssicherung. T2 - Jahrestreffen der VDMA Arbeitsgemeinschaft Additive Fertigung CY - Pegnitz, Germany DA - 13.10.2025 KW - Additive Fertigung KW - PBF-LB/M KW - Digitalisierung PY - 2025 AN - OPUS4-64402 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Epperlein, Martin T1 - Datengetriebene Qualitätssicherung für den PBF-LB/M Prozess N2 - Der Vortrag gibt einen Überblick über die aktuellen Aktivitäten im QI-Digital Use Case Additive Fertigung. Der Fokus liegt hier auf einer digitalen Qualitätssicherung. T2 - Symposium „Additive Fertigung: Pulverbasiertes Schmelzen mittels Laserstrahl“ CY - Leipzig, Germany DA - 14.08.2025 KW - Additive Fertigung KW - PBF-LB/M KW - Digitalisierung PY - 2025 AN - OPUS4-64400 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Epperlein, Martin T1 - Normungsaktivitäten in QI-Digital N2 - Der Vortrag thematisiert die Normungsaktivitäten in QI-Digital. Insbesondere die entwickelte Datenstruktur in der ISO/ASTM 52970 und die Anknüpfungspunkte zur Verwaltungsschale. Die ISO TC 261 / JG 85 und ihr entsprechender Scope werden vorgestellt. T2 - Sitzung des DIN NA-145-04-01 AA CY - Darmstadt, Germany DA - 01.04.2025 KW - Additive Fertigung KW - PBF-LB/M KW - Digitalisierung PY - 2025 AN - OPUS4-64403 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -