TY - CONF A1 - Karapanagiotis, Christos T1 - Towards predictive maintenance of hydrogen pressure vessels based on multi-sensor data fusion and digital twin modeling N2 - Hydrogen pressure vessels are among the most essential components for reliable hydrogen technology. Under current regulations, a mostly conservative strategy is employed, restricting the usage time of hydrogen pressure vessels without providing information on the real remaining lifetime. During the service life, pressure vessels are inspected periodically. However, no established method that can provide continuous monitoring or information on the remaining safe service life of the vessel. In this paper, we propose a sensor network for Structural Health Monitoring (SHM) of hydrogen pressure vessels where data from all sensors are collected and centrally evaluated. Specifically, we integrate three different SHM sensing technologies namely Guided Wave ultrasonics (GW), Acoustic Emission testing (AT), and distributed Fiber Optic Sensing (FOS). This integrated approach offers significantly more information and could therefore enable a transition from costly and time-consuming periodic inspections to more efficient and modern predictive maintenance strategies, including Artificial Intelligence (AI)-based evaluation. This does not only have a positive effect on the operational costs but enhances safety through early identification of critical conditions in the overall system in real-time. We demonstrate an experimental set-up of a lifetime test where a Type IV Composite Overwrapped Pressure Vessel (COPV) is investigated under cyclic loading instrumented with AT, FOS, and GW methods. We acquired data from the sensor network until the pressure vessel failed due to material degradation. The data collected using the three different SHM sensor technologies is planned to be evaluated individually, using data fusion, and AI. In the future, we aim to integrate the measurement setup into a hydrogen refueling station with the data stream implemented into a digital signal processing chain and a digital twin. T2 - 11th European Workshop on Structural Health Monitoring CY - Potsdam, Germany DA - 10.06.2024 KW - Hydrogen KW - Ultrasonic guided waves KW - Fiber optic sensors KW - Acoustic emission KW - Machine learning KW - Pressure vessels KW - Structural health monitoring PY - 2024 AN - OPUS4-60277 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Karapanagiotis, Christos T1 - Structural health monitoring of hydrogen pressure vessels using distributed fiber optic sensing N2 - We report on distributed fiber optic sensing-based monitoring of hydrogen composite overwrapped pressure vessels (COPV) to simultaneously increase the operational lifespan and mitigate maintenance costs. Our approach represents, to the best of our knowledge, the first application of distributed fiber optic sensing for COPV Type IV monitoring, where the sensing fibers are attached to the surface, rather than integrated into the composite material. Specifically, we attach an optical fiber of 50 m to the pressure vessel's surface, covering both the cylindrical and dome sections. We note that our fiber optic sensing technique relies on swept wavelength interferometry providing strain information along the entire length of the optical fiber with high spatial resolution even at the millimeter scale. When the vessel is pressurized, the sensing optical fiber shows a linear strain response to pressure at every position along the fiber. After thousands of load cycles, the vessel finally fails with the optical fiber detecting and precisely localizing the damage in the vessel’s blind dome area. Furthermore, we discuss the potential of state-of-the-art signal processing methods and machine learning for advancing predictive maintenance. This could reduce the number of regular inspections, mitigate premature maintenance costs, and simultaneously increase the vessel’s remaining safe service life. We believe that the structural health monitoring of hydrogen pressure vessels with fiber optic sensors can enhance trust in hydrogen technology contributing to the energy transition in the future. T2 - 11th European Workshop on Structural Health Monitoring CY - Potsdam, Germany DA - 10.06.2024 KW - Hydrogen KW - Composites KW - Pressure vessels KW - Fiber optic sensors KW - Machine learning KW - Structural health monitoring PY - 2024 AN - OPUS4-60275 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wosniok, Aleksander T1 - Distributed fiber optic strain sensing for structural health monitoring of 70 MPa hydrogen vessels N2 - We report on the development and testing of 70 MPa hydrogen pressure vessels with integrated fiber optic sensing fibers for automotive use. The paper deals with the condition monitoring of such composite pressure vessels (CPVs) using the optical backscatter reflectometry (OBR) applied for a distributed fiber optic strain sensing along fully integrated polyimide-coated single-mode glass optical fiber (SM-GOF). The sensing fibers were embedded into the vessel structure by wrapping them over the polymer liner during the manufacturing process of the carbon fiber reinforced polymer (CFRP). Detecting local strain events by the integrated fiber optic sensors can be an opportunity for monitoring the material degradation of CPVs under static and cyclic loading. T2 - 11th European Workshop on Structural Health Monitoring CY - Potsdam, Germany DA - 10.06.2024 KW - Fiber optic sensor KW - Distributed strain sensing KW - Composite pressure vessel KW - Structural health monitoring KW - Fiber-reinforced plastics PY - 2024 AN - OPUS4-60307 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heimann, Jan A1 - Yilmaz, Bengisu A1 - Charmi, Amir A1 - Duffner, Eric A1 - Schukar, Marcus A1 - Prager, Jens T1 - Structural Health Monitoring (SHM) for continuous monitoring of hydrogen pressure vessels N2 - While hydrogen is one of the most promising energy carriers, the safety of hydrogen storage technology remains one of the most important factors for technological and societal approval. While the engineering safety factors of the pressure vessels are kept high, the periodic inspection and the limited lifetime are making the application very costly considering manpower, time, money, and material waste. The development of an integrated structural health monitoring system can allow an easy transition from the current situation to cost-effective predictive maintenance. Hence, we propose to integrate three different SHM systems into hydrogen pressure vessels, namely guided wave ultrasonics, acoustic emission, and fibre optic sensing, to continuously monitor the condition and integrity. In this work, we evaluated the condition of a Type IV composite overwrapped pressure vessel using ultrasonic guided wave propagation. We mounted fifteen piezo-electric wafers on the composite cylinder by shaping three rings containing five sensors each. We acquired data from the sensor network following different boundary conditions with artificial damages on the selected locations. The data were evaluated with guided wave tomography techniques using ultrasonic features (amplitude, frequency, etc.) as well as artificial intelligence (AI). The results suggest that both traditional guided wave fusion techniques and AI-based characterization methods can detect artificial damages. In future work, it is planned to integrate acoustic emission and fibre optic sensing. Moreover, the measurement and the test results will be implemented into a digital twin to derive trends and make predictions on the damage propagation as well as the remaining useful lifetime. This work has received funding from German Ministry of Economic Affairs and Climate Actions within the QI-Digital initiative (www.qi-digital.de). T2 - SCHALL 23 CY - Wetzlar, Germany DA - 21.03.2023 KW - Structural Health Monitoring KW - Ultrasonic Guided Waves KW - Composite Overwrapped Pressure Vessel KW - Hydrogen PY - 2023 AN - OPUS4-58026 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bernardy, Christopher A1 - Konert, Florian A1 - Popiela, Bartosz A1 - Sarif, Raduan T1 - H2Safety@BAM: Competence Center for safe hydrogen technologies N2 - Presentation of the competence center H2Safety@BAM at the European PhD Hydrogen Conference 2024 in Ghent, Belgium. T2 - European PhD Hydrogen Conference 2024 (EPHyC2024) CY - Ghent, Belgium DA - 20.03.2024 KW - H2safety KW - Hydrogen KW - Safety KW - Competence center PY - 2024 AN - OPUS4-59756 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Terhedebrügge, Gabriel A1 - Prager, Jens T1 - How can SHM be applied in a quality assured and legally compliant manner? T1 - Wie kann SHM qualitätssicher und rechtssicher angewendet werden? N2 - Many SHM applications developed at universities and research institutions have not yet left the laboratory scale. Possible reasons for this include: - Real components and structures are often more complex than expected, - The POD (probability of detection) of the SHM system is usually difficult to determine, - The reliability of SHM systems is often unsatisfactory, and - The transition from recurring inspection to permanent monitoring with automated SHM systems fails due to existing safety regulations and testing standards. The workshop addresses these issues and aims to present solutions that facilitate the practical use of SHM. The solutions will be developed using real-world applications, such as those in the field of renewable energy. N2 - Viele SHM-Anwendungen, die an den Universitäten und Forschungseinrichtungen entwickelt wurden, haben den Labormaßstab noch nicht verlassen. Mögliche Gründe dafür sind, - dass reale Bauteile und Strukturen häufig komplexer sind als erwartet, - die POD (probability of detection) des SHM-Systems zumeist schwer bestimmbar ist, - die Zuverlässigkeit der SHM-Systeme oft nicht zufriedenstellend ist und - der Übergang von wiederkehrender Prüfung zur permanenter Überwachung mit automatisierten SHM-Systemen an vorhandenen Sicherheitsrichtlinien und Prüfvorschriften scheitert. Der Workshop greift diese Fragestellungen auf und soll Lösungsansätze aufzeigen, die den Einsatz von SHM in der Praxis erleichtern. Die Lösungen werden beispielhaft für reale Anwendungen, z.B. aus dem Bereich der erneuerbaren Energien, erarbeitet. T2 - SCHALL 25 CY - Dresden, Germany DA - 28.03.2025 KW - SHM KW - Legal aspects KW - Pressure vessels KW - SMART-tools KW - QI-Digital KW - Periodic inspection PY - 2025 AN - OPUS4-62909 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Karapanagiotis, Christos T1 - Toward a Digital Twin of Hydrogen Pressure Vessels Enabled by Distributed Fiber Optic Sensors N2 - We present a digital replica of a hydrogen pressure vessel enabled by distributed fiber optic sensors (DFOS). This digital replica dynamically displays and updates the vessel’s structural condition by calculating strain residuals defined as the difference between the measured DFOS strain and the expected strain based on pressure data. As an example, we show the ability of the DFOS to detect and localize damage caused by drilling six holes into the vessel’s body. This digital replica represents a foundational step toward a fully integrated digital twin for predictive maintenance and remaining lifetime prognosis. T2 - Sensor and Measurement Science International 2025 CY - Nuremberg, Germany DA - 06.05.2025 KW - Fiber optic sensors KW - Hydrogen KW - Digital twins KW - Structural health monitoring KW - Machine learning KW - Predictive maintenance PY - 2025 AN - OPUS4-63087 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Popiela, Bartosz A1 - Günzel, Stephan A1 - Schukar, Marcus A1 - Mair, Georg W. A1 - Krebber, Katerina A1 - Seidlitz, Holger T1 - Impact of internal pressure control during manufacturing on residual stresses and safety performance of type 4 pressure vessels N2 - Composite pressure vessels are commonly manufactured using the wet filament winding process, where various process parameters can influence the performance of the finished component. In this study two designs of wet filament wound 6.8-liter type 4 composite pressure vessels were manufactured. Both differ only by the internal pressure used during the filament winding, which primarily influences the residual stress state in the composite structure. An extensive experimental study was carried out, including 10 slow burst tests and strain measurements with fiber optic sensors. Significant differences can be observed in the performance of the two designs even though the used stacking sequence, materials and other manufacturing parameters are the same for both designs. A discussion of the differences in the behavior of both cylinder types is provided, including the strain distribution in slow burst tests and failure mechanism. KW - Residual stresses KW - Slow burst tests KW - Filament winding KW - Type 4 composite pressure vessels KW - Hydrogen PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-626663 DO - https://doi.org/10.1016/j.jcomc.2025.100581 SN - 2666-6820 VL - 17 SP - 1 EP - 9 PB - Elsevier B.V. CY - Amsterdam, Netherlands AN - OPUS4-62666 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - John, Sebastian T1 - Delfin - Statusbericht zum 4.HJM N2 - Präsentation über den Fortschritt der BAM zum Vorhaben Delfin, welches sich mit der Entwicklung und Schädigungsneigung von Composite-Wasserstoffbehältern für den Anwendungsfall KFZ beschäftigt T2 - 4. Halbjahresmeeting zum Vorhaben Delfin CY - Online meeting DA - 21.10.2020 KW - Wasserstoff KW - Impact KW - Druckbehälter PY - 2020 AN - OPUS4-51495 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Munzke, Dorit A1 - Duffner, Eric A1 - Eisermann, René A1 - Schukar, Marcus A1 - Schoppa, André A1 - Szczepaniak, Mariusz A1 - Strohhäcker, J. A1 - Mair, Georg W. T1 - Monitoring of type IV composite pressure vessels with multilayer fully integrated optical fiber based distributed strain sensing N2 - We present the results of distributed fiber optic strain sensing for condition monitoring of a hybrid type IV composite fully wrapped pressure vessel using multilayer integrated optical fibers. Distributed strain sensing was performed for a total number of 252,000 load cycles until burst of the vessel. During this ageing test material fatigue could be monitored and spatially localized. Critical material changes were detected 17,000 cycles before material failure. Results have been validated by acoustic emission analysis. T2 - 12th International Conference on Composite Science and Technology (ICCST12) CY - Sorrento, Italy DA - 08.05.2019 KW - Hybrid composite pressure vessel KW - Distributed fiber optic sensing KW - Acoustic emission analysis KW - Structural health monitoring PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-516772 DO - https://doi.org/10.1016/j.matpr.2020.02.872 SN - 2214-7853 VL - 34 SP - 217 EP - 223 PB - Elsevier Ltd. CY - Amsterdam AN - OPUS4-51677 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Popiela, Bartosz A1 - Schukar, Marcus A1 - Breithaupt, Mathias A1 - Günzel, Stephan A1 - Mair, Georg W. A1 - Krebber, Katerina A1 - Seidlitz, Holger T1 - Embedding of Fiber Optic Sensors Under Industrial Conditions and Distributed Strain Sensing in Type 4 Composite Pressure Vessels N2 - The number of in-operation composite pressure vessels is increasing, partly due to their attractiveness for on-board compressed gas storage and transport applications. A possible way to maintain the highest safety levels is through the structural health monitoring of the composite cylinders. Here, the use of fiber optic sensors appears to be a promising approach. However, the integration of the optical fibers into the composite structure of a pressure vessel has been shown to be challenging. In this study, insights on the embedding of optical fibers in the composite structure under industrial conditions are provided. A protection concept for the ingress and egress of the optical fibers is presented. Finally, the results from destructive slow burst tests are evaluated, showing no clear trend in the impact of the embedded optical fibers on the performance of composite pressure vessels. T2 - 24th International Conference on Composite Materials CY - Baltimore, Maryland, USA DA - 04.08.2025 KW - Composite KW - Pressure vessel KW - Filament winding KW - Fiber optic sensors PY - 2025 SP - 3710 EP - 3717 AN - OPUS4-63886 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Popiela, Bartosz T1 - Embedding of Fiber Optic Sensors Under Industrial Conditions and Distributed Strain Sensing in Type 4 Composite Pressure Vessels N2 - A presentation on the embedding of fiber optic sensors into the composite structure of type 4 composite pressure vessels. Also, the impact of the embedded fiber optic sensors on the burst pressures of type 4 composite pressure vessels was discussed. The presentation was held at ICCM24 in Baltimore, Maryland. T2 - 24th International Conference on Composite Materials CY - Baltimore, Maryland, USA DA - 04.08.2025 KW - Composite KW - Pressure vessel KW - Filament winding KW - Fiber optic sensors PY - 2025 AN - OPUS4-63885 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bühling, Benjamin A1 - Maack, Stefan T1 - Improving onset picking in ultrasonic testing by using a spectral entropy criterion N2 - In ultrasonic testing, material and structural properties of a specimen can be derived from the time-of-flight (ToF). Using signal features, such as the first peak or envelope maximum, to calculate the ToF is error-prone in multipath arrangements or dispersive and attenuating materials, which is not the case for the signal onset. Borrowing from seismology, researchers used the Akaike information criterion (AIC) picker to automatically determine onset times. The most commonly used formulation, Maeda's AIC picker, is reassessed and found to be based on inappropriate assumptions for signals often used in ultrasonic testing and dependent on arbitrary parameters. Consequently, an onset picker for ultrasonic through-transmission measurements is proposed, based on a spectral entropy criterion (SEC) to model the signal using the AIC framework. This SEC picker takes into account the spectral properties of the ultrasonic signal and is virtually free of arbitrary parameters. Synthetic and experimental data are used to compare the performance of SEC and AIC pickers. It is shown that the accuracy of onset picking is improved for densely sampled data. KW - Akaike information criterion picker KW - Nondestructive testing KW - Ultrasound KW - Time of flight PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-594284 UR - https://pubs.aip.org/asa/jasa/article/155/1/544/3061576/Improving-onset-picking-in-ultrasonic-testing-by DO - https://doi.org/10.1121/10.0024337 SN - 0001-4966 VL - 155 IS - 1 SP - 544 EP - 554 PB - AIP Publishing CY - Melville, NY, USA AN - OPUS4-59428 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Karapanagiotis, Christos A1 - Heimann, Jan A1 - Duffner, Eric A1 - Charmi, Amir A1 - Schukar, Marcus A1 - Hashemi, Seyedreza A1 - Prager, Jens T1 - Towards predictive maintenance of hydrogen pressure vessels based on multi-sensor data N2 - In this paper, we report on a sensor network for structural health monitoring (SHM) of Type IV composite overwrapped pressure vessels (COPVs) designed for hydrogen storage. The sensor network consists of three different SHM sensing technologies: ultrasonic guided waves (GW), acoustic emission (AE) testing, and distributed fiber optic sensors (DFOS). We present an experimental setup for a lifetime test, where a COPV is subjected to cyclic loading. Data from all sensors are collected and centrally evaluated. The COPV failed after approximately 60,000 load cycles, and the sensor network proved capable of detecting and localizing the damage even before the failure of the COPV. This multi-sensor approach offers significantly more channels of information and could therefore enable a transition from costly and time-consuming periodic inspections to more efficient and modern predictive maintenance strategies, including artificial intelligence (AI)-based evaluation. This not only has a positive effect on operational c KW - Ffiber optic sensors KW - Acoustic emission KW - Guided waves KW - Hydrogen KW - Digital twin KW - Structural health monitoring PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-618948 DO - https://doi.org/10.58286/30513 SP - 1 EP - 8 PB - NDT.net AN - OPUS4-61894 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wosniok, Aleksander A1 - Schukar, Marcus A1 - Woody, Paul A1 - Wang, Bin A1 - Breithaupt, Mathias A1 - Kriegsmann, Andreas T1 - Distributed fiber optic strain sensing for structural health monitoring of 70 MPa hydrogen vessels N2 - We report on the development and testing of 70 MPa hydrogen pressure vessels with integrated fiber optic sensing fibers for automotive use. The paper deals with the condition monitoring of such composite pressure vessels (CPVs) using the optical backscatter reflectometry (OBR) applied for a distributed fiber optic strain sensing along fully integrated polyimide-coated single-mode glass optical fiber (SM-GOF). The sensing fibers were embedded into the vessel structure by wrapping them over the polymer liner during the manufacturing process of the carbon fiber reinforced polymer (CFRP). Detecting local strain events by the integrated fiber optic sensors can be an opportunity for monitoring the material degradation of CPVs under static and cyclic loading. T2 - 11th European Workshop on Structural Health Monitoring CY - Potsdam, Germany DA - 10.06.2024 KW - Fiber optic sensor KW - Distributed strain sensing KW - Composite pressure vessel KW - Structural health monitoring KW - Fiber-reinforced plastics PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-603105 SP - 1 EP - 8 PB - NDT.net AN - OPUS4-60310 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heimann, Jan T1 - Innovative Real-Time Monitoring of H2 Pressure Vessels for Enhanced Safety and Reliability N2 - The significantly increased number of pressure vessels for storage and transport of H2 makes periodic manual inspections virtually impossible. Structural health monitoring enables proactive maintenance, extends the vessel’s lifespan, and ensures compliance with regulations, all while minimizing operational risks and downtime. T2 - QI-Digital Forum 2024 CY - Berlin, Germany DA - 09.10.2024 KW - Structural Health Monitoring KW - Pressure Vessel KW - Hydrogen KW - Reliability KW - Quality Infrastructure KW - Demonstrator PY - 2024 AN - OPUS4-61485 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Karapanagiotis, Christos A1 - Heimann, Jan A1 - Duffner, Eric A1 - Charmi, Amir A1 - Schukar, Marcus A1 - Hashemi, Seyedreza A1 - Prager, Jens T1 - Towards predictive maintenance of hydrogen pressure vessels based on multi-sensor data fusion and digital twin modeling N2 - Hydrogen pressure vessels are among the most essential components for reliable hydrogen technology. Under current regulations, a mostly conservative strategy is employed, restricting the usage time of hydrogen pressure vessels without providing information on the real remaining lifetime. During the service life, pressure vessels are inspected periodically. However, no established method that can provide continuous monitoring or information on the remaining safe service life of the vessel. In this paper, we propose a sensor network for Structural Health Monitoring (SHM) of hydrogen pressure vessels where data from all sensors are collected and centrally evaluated. Specifically, we integrate three different SHM sensing technologies namely Guided Wave ultrasonics (GW), Acoustic Emission testing (AT), and distributed Fiber Optic Sensing (FOS). This integrated approach offers significantly more information and could therefore enable a transition from costly and time-consuming periodic inspections to more efficient and modern predictive maintenance strategies, including Artificial Intelligence (AI)-based evaluation. This does not only have a positive effect on the operational costs but enhances safety through early identification of critical conditions in the overall system in real-time. We demonstrate an experimental set-up of a lifetime test where a Type IV Composite Overwrapped Pressure Vessel (COPV) is investigated under cyclic loading instrumented with AT, FOS, and GW methods. We acquired data from the sensor network until the pressure vessel failed due to material degradation. The data collected using the three different SHM sensor technologies is planned to be evaluated individually, using data fusion, and AI. In the future, we aim to integrate the measurement setup into a hydrogen refueling station with the data stream implemented into a digital signal processing chain and a digital twin. T2 - 11th European Workshop on Structural Health Monitoring CY - Potsdam, Germany DA - 10.06.2024 KW - Acoustic emission KW - Ultrasonic guided waves KW - Fiber optic sensors KW - Hydrogen KW - Pressure vessels KW - Structural health monitoring KW - Machine learning PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-602764 UR - https://www.ndt.net/search/docs.php3?id=29702 SP - 1 EP - 8 PB - NDT.net AN - OPUS4-60276 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Karapanagiotis, Christos A1 - Schukar, Marcus A1 - Breithaupt, Mathias A1 - Duffner, Eric A1 - Ulbricht, Alexander A1 - Prager, Jens A1 - Krebber, Katerina T1 - Structural health monitoring of hydrogen pressure vessels using distributed fiber optic sensing N2 - We report on distributed fiber optic sensing-based monitoring of hydrogen composite overwrapped pressure vessels (COPV) to simultaneously increase the operational lifespan and mitigate maintenance costs. Our approach represents, to the best of our knowledge, the first application of distributed fiber optic sensing for COPV Type IV monitoring, where the sensing fibers are attached to the surface, rather than integrated into the composite material. Specifically, we attach an optical fiber of 50 m to the pressure vessel's surface, covering both the cylindrical and dome sections. We note that our fiber optic sensing technique relies on swept wavelength interferometry providing strain information along the entire length of the optical fiber with high spatial resolution even at the millimeter scale. When the vessel is pressurized, the sensing optical fiber shows a linear strain response to pressure at every position along the fiber. After thousands of load cycles, the vessel finally fails with the optical fiber detecting and precisely localizing the damage in the vessel’s blind dome area. Furthermore, we discuss the potential of state-of-the-art signal processing methods and machine learning for advancing predictive maintenance. This could reduce the number of regular inspections, mitigate premature maintenance costs, and simultaneously increase the vessel’s remaining safe service life. We believe that the structural health monitoring of hydrogen pressure vessels with fiber optic sensors can enhance trust in hydrogen technology contributing to the energy transition in the future. T2 - 11th European Workshop on Structural Health Monitoring CY - Potsdam, Germany DA - 10.06.2024 KW - Hydrogen KW - Fiber optic sensors KW - Composites KW - Machine learning KW - Structural health monitoring PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-602731 UR - https://www.ndt.net/search/docs.php3?id=29701 SP - 1 EP - 7 PB - NDT.net AN - OPUS4-60273 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Karapanagiotis, Christos A1 - Breithaupt, Mathias A1 - Duffner, Eric A1 - Schukar, Marcus T1 - Real-time monitoring of hydrogen composite pressure vessels using surface-applied distributed fiber optic sensors N2 - In this paper, we report to the best of our knowledge for the first time on continuous real-time monitoring of composite overwrapped pressure vessels (COPVs) designed for hydrogen storage using surface-applied distributed fiber optic sensors (DFOS). We conducted continuous and real-time DFOS measurements during pressure cycling tests consisting of periodic pressure fluctuations between 20 bar and 875 bar, with a rate of 5 cycles min−1. During pressure cycling, the DFOS system measured strain changes, that under normal operating conditions were linearly correlated to changes in pressure. To detect and quantify damage-related anomalies, we trained a simple regression model to predict strain from pressure data and used the difference between predicted and measured values as a damage indicator. With our approach, the DFOS system not only detected and localized the damage but also continuously tracked its evolution in real time under dynamic pressure conditions. Furthermore, unlike previous studies where optical fibers were embedded within the composite structure, we applied them on the COPV surface, reducing both implementation cost and time while eliminating the need to modify the COPV manufacturing process. Based on our results, we are confident that DFOS can enhance safety and facilitate the transition from time-consuming periodic inspections to more efficient, machine learning-based predictive maintenance. KW - Fiber optic sensors KW - Hydrogen KW - Structural health monitoring KW - Pressure vessels KW - Predictive maintenance PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-627644 DO - https://doi.org/10.1088/2515-7647/adb9ac SN - 2515-7647 VL - 7 IS - 2 SP - 2 EP - 10 PB - IOP Publishing Ltd CY - Bristol, UK AN - OPUS4-62764 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Popiela, Bartosz A1 - Günzel, Stephan A1 - Oktaviany, Jennifer A1 - Widjaja, Martinus Putra A1 - Mair, Georg W. A1 - Seidlitz, Holger T1 - Influence of Internal Pressure Regulation During Filament Winding on Failure Mechnism in Type 4 Pressure Vessels: A Case Study N2 - Hydrogen storage is a crucial part of the hydrogen value chain, particularly in terms of safety and social acceptance of hydrogen technologies. For on-board and transportation applications, hydrogen is commonly stored as a compressed gas in pressure vessels. Full composite wrapped Type 4 pressure vessels are especially beneficial due to their high weight-saving potential and their capability to withstand high working pressures. To maintain an appropriate safety level, the mechanical behavior of the composite structure has been the subject of investigation in numerous studies. In this study, the failure mechanisms of two designs of Type 4 cylinders are investigated. The two designs differ solely in the manufacturing process parameters, particularly the internal pressure applied during the filament winding process. Variations in internal pressure result in different residual stress states and changes in the quality of the composite structure. The stacking sequence, materials used, and other manufacturing parameters remain unchanged. The cylinders show different failure mechanisms in slow burst tests: one design fails in hoop windings, while the other one fails in helical windings, despite no stress exaggeration in the fiber direction being observed with embedded optical fibers or in numerical simulations. To explain the failure mechanisms, the quality of the cylinders is investigated. The results of X-ray computed tomography and pulse-echo investigation, highlight the complexity of the interactions between manufacturing process parameters, residual stresses, manufacturing quality, and the mechanical behavior of composite pressure vessels. Resin-rich areas in the composite material are identified as a possible cause of the differing failure mechanisms. T2 - 11th International Conference on Hydrogen Safety ICHS 2025 CY - Seoul, South Korea DA - 22.09.2025 KW - Composite KW - Pressure vessel KW - Filament winding KW - Burst test PY - 2025 SP - 1 EP - 12 AN - OPUS4-64452 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Widjaja, Martinus Putra A1 - Moosavi, Robabeh A1 - John, Sebastian A1 - Schumacher, David A1 - Grunwald, Marcel A1 - Auster, Jürgen A1 - Szczepaniak, Marius A1 - Mair, Georg W. A1 - Waske, Anja T1 - Impact damage evaluation of hydrogen composite pressure vessels by analysing computed tomography images N2 - The objective of this work is to find a method that describes the degree of damage from an impact experiment. This experiment was performed on Composite Pressure Vessels (CPV) in order to find the correlation of impact damage to the residual burst pressure. Computed Tomography (CT) approach was used to capture the before and after impact condition of the CPVs. The Wasserstein function was used to calculate how much the after impact image has differed from the original one. In the end, a good correlation was obtained to the residual burst pressure. T2 - HyFiSyn Conference CY - Online meeting DA - 15.09.2021 KW - Hydrogen KW - Composite pressure vessel KW - Carbon fibre KW - Burst test KW - Image analysis KW - Computed tomography (CT) PY - 2021 SP - 31 EP - 32 AN - OPUS4-53494 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Widjaja, Martinus Putra T1 - Impact damage evaluation of hydrogen composite pressure vessels by analysing computed tomography images N2 - The objective of this work is to find a method that describes the degree of damage from an impact experiment. This experiment was performed on Composite Pressure Vessels (CPV) in order to find the correlation of impact damage to the residual burst pressure. Computed Tomography (CT) approach was used to capture the before and after impact condition of the CPVs. The Wasserstein function was used to calculate how much the after impact image has differed from the original one. In the end, a good correlation was obtained to the residual burst pressure. The smaller the Wasserstein distance is, the higher the residual burst pressure would be and vice versa. T2 - HyFiSyn Conference CY - Online meeting DA - 15.09.2021 KW - Hydrogen KW - Composite pressure vessel KW - Carbon fibre KW - Burst test KW - Image analysis KW - Computed tomography (CT) PY - 2021 AN - OPUS4-53496 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - John, Sebastian T1 - Current results of the DELFIN project N2 - As a contribution to the national hydrogen strategy, 3.5 years ago, the Delfin research project started with the aim of developing a cost- and material-optimized hydrogen tank design for automotive application. Under the patronage of the National Organization Hydrogen and Fuel Cell Technology (NOW), a consortium consisting of 9 research institutes, component suppliers, engineering service providers and automobile OEMs is processing a wide range of work packages. The focus of BAM research sets on impact testing and safety-related characterization of pressure vessels of different development stages. Furthermore, the implementation of nondestructive testing methods is applied. The presentation shows an overview of the BAM work packages and an extraction of the results generated so far. T2 - Wasserstoffkolloquium des Kompetenzzentrums H2Safety@BAM CY - Online meeting DA - 16.02.2022 KW - Delfin KW - Wasserstoff KW - Druckbehälter KW - Impact PY - 2022 AN - OPUS4-55348 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - John, Sebastian T1 - Vorstellung NIP II FORSCHUNGSVORHABEN DELFIN N2 - As a contribution to the national hydrogen strategy, 3.5 years ago, the Delfin research project started with the aim of developing a cost- and material-optimized hydrogen tank design for automotive application. Under the patronage of the National Organization Hydrogen and Fuel Cell Technology (NOW), a consortium consisting of 9 research institutes, component suppliers, engineering service providers and automobile OEMs is processing a wide range of work packages. The focus of BAM research sets on impact testing and safety-related characterization of pressure vessels of different development stages. Furthermore, the implementation of nondestructive testing methods is applied. The presentation shows an overview of the BAM work packages and an extraction of the results generated so far. T2 - SAMPE Feierabendkolloqium CY - Online meeting DA - 15.06.2022 KW - Delfin KW - Wasserstoff KW - Druckbehälter KW - Impact PY - 2022 AN - OPUS4-55349 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maiwald, Michael T1 - Competence Centre H2Safety@BAM – Safeguarding the Quality Infrastructure in the Hydrogen Economy N2 - Hydrogen is a central component of the energy transition and the European Green Deal for a climate-neutral Europe. To achieve the goals defined for 2050, the EU and the German government have developed a framework for action and are making long-term investments in research, development, and the rapid implementation of innovative hydrogen technologies. With the Competence Centre "H2Safety@BAM", BAM is creating the safety-related prerequisites for the successful implementation of hydrogen technologies at national as well as European level. To this end, BAM conducts research, testing and consulting in a holistic and inter-disciplinary manner under one roof – in the Competence Centre H2Safety@BAM. The activities of the competence centre focus on ensuring the safety of infra-structures, plants, and processes as well as innovative hydrogen transport and storage systems based on digital quality testing and the experimental testing of components and systems. It thus creates the prerequisites for the implementation and adaptation of legal framework conditions as well as for standardization. Closely related to this are investigations into the properties and compatibility of metallic materials and polymers as well as friction systems for the safe operation of components, plants, processes, and systems. This interdisciplinary and holistic approach is complemented by the development of gas analytics and suitable sensors, online measurements of gas properties in process control, test scenarios under real conditions as well as impact assessments of accidents and risk assessments and risk management systems derived from them. With its portfolio of tasks and competences, BAM builds trust in the safety and reliability of technical system solutions for hydrogen. T2 - 772. WE-Heraeus-Seminar - Metrology and Process Safety for Hydrogen Technologies & Applications CY - Bad Honnef, Germany DA - 10.10.2022 KW - H2Safety@BAM KW - Hydrogen KW - Competence Center KW - Hydrogen Strategy KW - Green Deal KW - Safety KW - Risk Assessment KW - Quality Infrastructure PY - 2022 UR - https://www.we-heraeus-stiftung.de/veranstaltungen/metrology-and-process-safety-for-hydrogen-technologies-and-applications/ AN - OPUS4-55986 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Orellana Pérez, Teresa T1 - Die Wasserstoffstrategie der BAM; Kompetenzzentrum H 2 safety@bam N2 - Das Thema Wasserstoff ist an der BAM seit mehr als hundert Jahren aktuell und steht auch gegenwärtig im Zentrum zahlreicher Forschungs- und Kooperationsaktivitäten. Mit der aktuellen Wasserstoff-Strategie der BAM werden wichtige Voraussetzungen dafür geschaffen, dass der Markthochlauf gelingt und die technische Sicherheit und Überwachung der Infrastrukturen und Anlagen gewährleistet ist – von der Erzeugung, über den Transport bis zur Speicherung und Bereitstellung von Wasserstoff als Energieträger der Zukunft. T2 - 1st Digital AK PostDocs Meeting CY - Online meeting DA - 01.10.2020 KW - Kompetenzzentrum H2Safety@BAM KW - Wasserstoff KW - Wasserstoffstrategie PY - 2020 AN - OPUS4-51371 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - John, Sebastian A1 - Auster, Jürgen A1 - Widjaja, Martinus Putra A1 - Duffner, Eric A1 - Mair, Georg W. T1 - NIP II - Forschungsvorhaben „DELFIN“ N2 - Überblick über Projektinhalte und -ergebnisse aus dem Forschungsvorhaben Delfin „Erforschung alternativer Materialien und Fertigungsprozesse für kosten- und gewichtsreduzierte Druckbehälter aus endlosfaserverstärkten Kunststoff“ T2 - SAMPE Kolloquium CY - Online meeting DA - 15.01.2022 KW - Wasserstoff KW - Druckbehälter KW - Impact PY - 2022 AN - OPUS4-58064 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. T1 - Influence of Internal Pressure Regulation During Filament Winding on Failure Mechnism in Type 4 Pressure Vessels: A Case Study N2 - Hydrogen storage is a crucial part of the hydrogen value chain, particularly in terms of safety and social acceptance of hydrogen technologies. For on-board and transportation applications, hydrogen is commonly stored as a compressed gas in pressure vessels. Full composite wrapped Type 4 pressure vessels are especially beneficial due to their high weight-saving potential and their capability to withstand high working pressures. To maintain an appropriate safety level, the mechanical behavior of the composite structure has been the subject of investigation in numerous studies. In this study, the failure mechanisms of two designs of Type 4 cylinders are investigated. The two designs differ solely in the manufacturing process parameters, particularly the internal pressure applied during the filament winding process. Variations in internal pressure result in different residual stress states and changes in the quality of the composite structure. The stacking sequence, materials used, and other manufacturing parameters remain unchanged. The cylinders show different failure mechanisms in slow burst tests: one design fails in hoop windings, while the other one fails in helical windings, despite no stress exaggeration in the fiber direction being observed with embedded optical fibers or in numerical simulations. To explain the failure mechanisms, the quality of the cylinders is investigated. The results of X-ray computed tomography and pulse-echo investigation, highlight the complexity of the interactions between manufacturing process parameters, residual stresses, manufacturing quality, and the mechanical behavior of composite pressure vessels. Resin-rich areas in the composite material are identified as a possible cause of the differing failure mechanisms. T2 - 11th International Conference on Hydrogen Safety ICHS 2025 CY - Seoul, Republic of Korea DA - 22.09.2025 KW - omposite KW - Pressure vessel KW - Filament winding KW - Slow burst test KW - Failure mechanism PY - 2025 AN - OPUS4-64462 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Popiela, Bartosz A1 - Günzel, Stephan A1 - Sklorz, Christian A1 - Widjaja, Martinus Putra A1 - Mair, Georg W. A1 - Seidlitz, Holger T1 - Application of the incremental hole-drilling method for residual stress determination in type 4 pressure vessels N2 - Hole-drilling method is a standardized technique for obtaining residual stresses in isotropic structures. Previous studies provide a foundation that enables the use of this method to investigate orthotropic structures, such as fiber-reinforced composites. In this study, the incremental hole-drilling method was applied to investigate residual stresses in filament wound type 4 composite pressure vessels. The investigated composite cylinders were manufactured with different internal pressure functions during the winding process, to achieve distinct residual stress states. Additionally, the influence of the initial loading under sustained internal pressure and increased temperature on the stress distribution was investigated. It was shown that the residual stress state can be influenced by varying the internal pressure in the winding process. After testing at sustained load and increased temperature, a stress redistribution was observed, which took place due to creep phenomena. Finally, a discussion of the challenges for the application of the hole-drilling method to composite pressure vessels is provided. KW - Hole-drilling method KW - Filament winding KW - Type 4 composite pressure vessels KW - Residual stresses KW - Stress redistribution PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-627765 DO - https://doi.org/10.1515/mt-2024-0328 SN - 2195-8572 VL - 67 IS - 4 SP - 663 EP - 674 PB - Walter de Gruyter GmbH AN - OPUS4-62776 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tiebe, Carlo T1 - Sensoren und Analytik für Sicherheit und Prozesskontrolle in Wasserstofftechnologien N2 - Der Beitrag beinhaltet Themen vom H2Safety@BAM-Kompetenzfeld Sensorik, Analytik und zertifizierte Referenzmaterialien (SensRef) mit Fokus auf Mess- und Prüfverfahren mit verschiedenen Sensortechnologien und Ultraschallwellen: Metrologie zur Wasserstoffspeicherung - Euramet-Vorhaben "MefHySto", Erkennung von freigesetztem Wasserstoff sowie die Bestimmung des Wasserstoff-Luftverhälntisses mit Gassensoren, zerstörungsfreie Fehlstellenerkennung mit integriertem Zustandsüberwachungssystem basierend auf geführten Ultraschallwellen zur Lebensdauerüberwachung von Composite-Behältern (Wasserstoffspeicher) sowie faseroptische Sensorik zur Schadenfrüherkennung von Wasserstoffspeichern aufgrund erkennbarer Dehnungsänderungen an Druckbehältern. T2 - DVGW Kongress H2 Sicherheit CY - Online meeting DA - 23.11.2022 KW - H2Safety@BAM KW - SensRef KW - Faseroptische Sensorik KW - Gassensorik KW - Geführte Ultraschallwellen KW - Leckdetektion KW - Metrologie zur Wasserstoffspeicherung KW - Zerstörungsfreie Prüfung KW - Structural Health Monitoring (SHM) PY - 2022 AN - OPUS4-56683 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tiebe, Carlo T1 - Prüf- und Messverfahren mit verschiedenen Sensortechnologien und Ultraschallwellen N2 - Der Vortrag zum Mess- und Prüfverfahren mit verschiedenen Sensortechnologien und Ultraschallwellen beinhaltet die Themen: Metrologie zur Wasserstoffspeicherung - Euramet-Vorhaben "MefHySto", Erkennung von freigesetztem Wasserstoff sowie die Bestimmung des Wasserstoff-Luftverhälntisses mit Gassensoren, zerstörungsfreie Fehlstellenerkennung mit integriertem Zustandsüberwachungssystem basierend auf geführten Ultraschallwellen zur Lebensdauerüberwachung von Composite-Behältern (Wasserstoffspeicher) sowie faseroptische Sensorik zur Schadenfrüherkennung von Wasserstoffspeichern aufgrund erkennbarer Dehnungsänderungen an Druckbehältern. T2 - DVGW Kongress H2 Sicherheit CY - Online meeting DA - 28.09.2021 KW - Leckdetektion KW - Metrologie zur Wasserstoffspeicherung KW - Gassensorik KW - Structural Health Monitoring (SHM) KW - Geführte Ultraschallwellen KW - Faseroptische Sensorik KW - Zerstörungsfreie Prüfung PY - 2021 AN - OPUS4-54136 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tiebe, Carlo T1 - Mess- und Prüfverfahren mit Sensorik N2 - Mess- und prüftechnische Verfahren sind zur Prozesskontrolle und Sicherheitsüberwachung in Wasserstofftechnologien von hoher Bedeutung. Typische Anwendungsgebiete von Sensoren sind Sicherheitsüberwachung, Leckdetektion und Prozesskontrolle. In diesem Beitrag werden Themen zur Erkennung von freigesetztem Wasserstoff sowie die Bestimmung des Wasserstoff-Luftverhältnisses mit Gassensoren, Fehlstellenerkennung mit geführten Ultraschallwellen zur Lebensdauerüberwachung (Structural Health Monitoring) von Wasserstoffspeichern sowie der Einsatz faseroptischer Sensoren zur Überwachung des Dehnungs- und Alterungsverhaltens sowie zur Schadensfrüherkennung von Wasserstoffspeichern vorgestellt. T2 - DVGW Kongress H2 Sicherheit CY - Online meeting DA - 27.01.2021 KW - Metrologie KW - Gassensoren KW - Structural Health Monitoring KW - Faseroptische Sensoren KW - Wasserstoff PY - 2021 AN - OPUS4-52141 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wosniok, Aleksander A1 - Schukar, Marcus A1 - Breithaupt, Mathias A1 - Kriegsmann, Andreas T1 - Distributed Fibre Optic Monitoring of Hydrogen Storage Composite Pressure Vessels for Automotive Use N2 - We present our research work on the condition monitoring of hydrogen storage composite pressure vessels using distributed fibre optic sensors. The sensing fibres are integrated into the composite structure by wrapping them over the polymer liner in the helical and circumferential direction during the manufacturing process of the carbon fibre reinforced polymer. The following use of optical backscatter reflectometry allows for continuous condition monitoring and precise detection and localization of structural damages during the entire service life. To account for the time-dependent strength degradation of the composite pressure vessels, both slow burst and ambient hydraulic cycling tests, respectively, were conducted on five 70 MPa pressure vessels with integrated fibre optic sensors. The results achieved via distributed fibre optic strain sensing demonstrate a near linear strain response to pressure suitable for sensitive condition monitoring and confirm the required robustness of the selected sensor solution. T2 - DGZfP-Jahrestagung 2025 CY - Berlin, Germany DA - 26.05.2025 KW - Distributed fibre optic sensor (DFOS) KW - Composite pressure vessel KW - Optical backscatter reflectometry KW - Slow burst test KW - Ambient hydraulic cycling test PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-653067 DO - https://doi.org/10.58286/32344 SP - 1 EP - 8 PB - NDT.net AN - OPUS4-65306 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kehr, Torsten T1 - Project QI-Digital - Quo vadis Use Case H2 Refueling Station? N2 - As a part of the QI-Digital cooperation project, BAM is setting up a hydrogen refuelling station research platform at the Test site for Technical Safety in Horstwalde. Based on this platform, BAM intends to develop, to test and to optimize new measurement techniques as well as data acquisition and processing methods for hydrogen refuelling stations and their periphery in close cooperation with partners from the quality infrastructure and industry. The presentation will introduce the hydrogen refuelling station use case and provide insights into the issues and research goals of the associated subprojects. T2 - H2-Colloquium of the Competence Centre „H2SAFETY@BAM” CY - Online meeting DA - 16.02.2022 KW - Hydrogen KW - Safety KW - QI-Digital PY - 2022 AN - OPUS4-54361 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -