TY - JOUR A1 - Redda, Zinnabu T. A1 - Brennecke, Daniel A1 - Prinz, Carsten A1 - Yimam, Abubeker A1 - Barz, Mirko A1 - Kadow, Steffen A1 - Laß-Seyoum, Asnakech T1 - Synthesis and characterization of AlPO4-18 supported mesoporous and crystalline β-Mo2C, Ni3C, and WC nanoparticles N2 - Developing high-efficiency, high-stability, and low-cost deoxygenation and hydrocracking catalysts could be considered one of the most significant breakthroughs in catalytic hydroprocessing. The present study utilized aluminophosphate (AlPO4-18), a zeolite-like molecular sieve, as catalyst support for producing carbon-coated β-Mo2C, Ni3C, and WC nanoparticles. The synthesis used an incipient wetness impregnation followed by a temperature-programmed reduction-carburization approach which involved cracking a hydrocarbon gas, propane, in a hydrogen environment. The synthesis parameters were a 1:7 propane/hydrogen reductive-carburizing gas stream, 15 wt.% metal loading, an 800 °C carburization temperature ramped-up at a heating rate of 10 °C min−1, a 2-h holding time, and a 1-h holding time in hydrogen. The synthesized catalysts were characterized using thermogravimetry mass spectroscopy/temperature-programmed oxidation (TPO TG-MS), nitrogen physisorption at 77 K, X-ray diffraction (XRD), and transmission electron microscopy/energy-dispersive X-ray spectroscopy (TEM EDS). TPO TG-MS, nitrogen physisorption, TEM, and XRD characterization results proved that atomic carbon was successfully incorporated into the lattice interstitials, resulting in thermally stable, well-dispersed, crystalline and mesoporous β-Mo2C/AlPO4-18, Ni3C/AlPO4-18, and WC/AlPO4-18 nanoparticles. XRD analysis showed structural evolution during reduction-carburization, with average crystallite sizes of metal-containing particles of 8.2–9.22, 6.64–8.50, and 6.03–7.56 nm for β-Mo2C/AlPO4-18, Ni3C/AlPO4-18, and WC/AlPO4-18, respectively. These values did not significantly deviate from high-resolution TEM analysis. The surface areas of the nanoparticles were categorized in decreasing order as WC/AlPO4-18 > Ni3C/AlPO4-18 > β-Mo2C/AlPO4-18, with values of 193.79, 169.05, and 66.57 m2 g−1, respectively. In conclusion, these carbon-coated metal carbide nanoparticles with excellent thermal, structural, microscopic, and textural properties can be viable alternatives to noble metal catalysts for producing bio-jet fuel using the hydroprocessing pathway. KW - Catalyst synthesis KW - Temperature-programmed reduction-carburization KW - Catalyst characterization KW - BET surface area KW - Nanoparticle KW - Transition metal carbide catalyst KW - TEM PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-608182 DO - https://doi.org/10.1007/s10562-024-04791-y SN - 1011-372X SN - 1572-879X VL - 154 SP - 5969 EP - 5988 PB - Springer Science and Business Media CY - Dordrecht AN - OPUS4-60818 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ruehle, Bastian T1 - A Self-Driving Lab for Nano and Advanced Materials Synthesis N2 - Nano- and advanced materials have been recognized as a key enabling technology of the 21st century, due to their high potential of driving innovations in new clean energy technologies, sustainable manufacturing by substitution of critical raw materials and replacement of hazardous substances, breakthroughs in energy conversion and storage, improvement of the environmental performance of products and processes, and facilitation of circularity. Consequently, new tools that enhance the development and optimization cycle of nano- and advanced materials are crucial. In this contribution, we present our Self-Driving Lab (SDL) for Nano and Advanced Materials [1], that integrates robotics for batched autonomous synthesis – from molecular precursors to fully purified nanomaterials – with automated characterization and data analysis, for a complete and reliable nanomaterial synthesis workflow. By fully automating the processing steps for seven different materials from five representative, completely different classes of nano- and advanced materials (metal, metal oxide, silica, metal organic framework, and core–shell particles) that follow different reaction mechanisms, we demonstrate the great versatility and flexibility of the platform. The system also exhibits high modularity and adaptability in terms of reaction scales and incorporates in-line characterization measurement of hydrodynamic diameter, zeta potential, and optical properties (absorbance, fluorescence). We discuss the excellent reproducibility of the various materials synthesized on the platform in terms of particle size and size distribution, and the adaptability and modularity that allows access to a diverse set of nanomaterial classes. We also present several key aspects of the central backend that orchestrates the (parallelized) syntheses workflows. One key feature is the resource management or “traffic control” for scheduling and executing parallel reactions in a multi-threaded environment. Another is the interface with data analysis algorithms from in-line, at-line, and off-line measurements. Here, we will give examples of how automatic image segmentation of electron microscopy images with the help of AI [2] can be used for reducing the “data analysis bottleneck” from an off-line measurement. We will also discuss various machine learning (ML) algorithms that are currently implemented in the backend and can be used for ML-guided, closed-loop material optimization in our SDL. Lastly, we will show our recent efforts [3] in making the workflow generation on SDLs more user-friendly by using large language models to generate executable workflows automatically from synthesis procedures given in natural language and user-friendly graphical user interfaces based on node editors that also allow for knowledge graph extraction from the workflows. In this context, we are currently also working on a common description or ontology for representing the process steps and parameters of the workflows, which will greatly facilitate the semantic description and interoperability of workflows between different SDL hardware and software platforms. These features underscore the SDL’s potential as a transformative tool for advancing and accelerating the development of nano- and advanced materials, offering solutions for a sustainable and environmentally responsible future. T2 - MRS Fall Meeting 2025 CY - Boston, MA, USA DA - 30.11.2025 KW - Self-Driving Labs KW - Materials Acceleration Platforms KW - Advanced Materials KW - Nanomaterials KW - Automation PY - 2025 AN - OPUS4-65129 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Habibimarkani, Heydar A1 - Prinz, Carsten A1 - Sahre, Mario A1 - Hodoroaba, Vasile-Dan A1 - Radnik, Jörg T1 - CV, TEM, XRD and XPS/HAXPES datasets of FeNi-based nanoparticles for the oxygen evolution reaction N2 - The datasets from Cyclic Voltammetry, Transmision Electron Microscopy, X-ray Diffraction, and (Hard Energy) X-ray Photoelectron Spectroscopy are related to the publication H. Habibimarkani, S.-L. Abram, A. Guilherme Buzanich, C. Prinz, M. Sahre, V.-D. Hodoroaba and J. Radnik "In-depth analysis of FeNi-based nanoparticles for the oxygen evolution reaction" Scientific Reports (2025), https://doi.org/10.1038/s41598-025-92720-3 Details of the materials and the experimental procedures are described in this publications. KW - Oxygen evolution reaction KW - Fe-Ni nanopartices KW - Comprehensive analysis PY - 2025 DO - https://doi.org/10.5281/zenodo.14975964 PB - Zenodo CY - Geneva AN - OPUS4-63335 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Andresen, Elina A1 - Resch-Genger, Ute A1 - Michaelis, Matthias A1 - Prinz, Carsten A1 - Würth, Christian T1 - Time-resolved luminescence spectroscopy for monitoring the stability and dissolution behaviour of upconverting nanocrystals with different surface coatings† N2 - We demonstrate the potential of time-resolved luminescence spectroscopy for the straightforward assessment and in situ monitoring of the stability of upconversion nanocrystals (UCNPs). Therefore, we prepared hexagonal NaYF4:Yb3+,Er3+ UCNPs with various coatings with a focus on phosphonate ligands of different valency, using different ligand exchange procedures, and studied their dissolution behaviour in phosphate-buffered saline (PBS) dispersions at 20 °C and 37 °C with various analytical methods. The amount of the released UCNPs constituting fluoride ions was quantified by potentiometry using a Fluoride ion-sensitive electrode and particle disintegration was confirmed by transmission electron microscopy studies of the differently aged UCNPs. In parallel, the luminescence features of the UCNPs were measured with special emphasis on the lifetime of the sensitizer emission to demonstrate its suitability as Screening parameter for UCNP stability and changes in particle composition. The excellent correlation between the changes in luminescence lifetime and fluoride concentration highlights the potential of our luminescence lifetime method for UCNP stability screening and thereby indirect monitoring of the release of potentially hazardous fluoride ions during uptake and dissolution in biological systems. Additionally, the developed in situ optical method was used to distinguish the dissolution dynamics of differently sized and differently coated UCNPs. KW - Fluorescence KW - Lifetime KW - Method KW - Quantification KW - Stability KW - Coating KW - Surface chemistry KW - Lanthanide KW - Fluoride KW - Electrochemistry KW - ICP-OES KW - Upconversion KW - Nano KW - Particle KW - Aging KW - Quality assurance KW - TEM PY - 2020 DO - https://doi.org/10.1039/d0nr02931a VL - 12 IS - 23 SP - 12589 EP - 12601 PB - Royal Society od Chemistry AN - OPUS4-52088 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Silbernagl, Dorothee A1 - Szymoniak, Paulina A1 - Tavasolyzadeh, Zeynab A1 - Sturm, Heinz A1 - Topolniak, Ievgeniia T1 - Interpenetrating networks with tuned thermal and mechanical properties N2 - Text Multiphoton lithography (MPL) has recently attracted significant research interest as a versatile tool capable of producing 2D and 3D micro- and nanoscopic features with high spatial resolution. The integrity of MPL microstructures, or their ability to respond to external stimuli, is of critical importance. However, achieving the desired properties of fabricated microcomponents for a specific application remains a challenge. In this work, we present new MPL materials based on epoxy-acrylate interpenetrating networks (IPNs). We aim at 3D microstructures, whose properties can be easily tuned by varying the ratio of the IPN components and fabrication parameters (Figure 1). The resulting library of 3D microstructures was investigated for their thermal and mechanical properties using highly-sensitive space-resolved methods. Flash scanning calorimetry revealed the influence of both, IPN composition and fabrication parameters, on glass transition temperature and material fragility. AFM force-distance curve and intermodulation methods were used to characterize the mechanical properties with a lateral resolution of 1 micron and 4 nm, respectively. The deformation, stiffness and elastic behavior are discussed in detail in relation to the morphology. Moreover, we found that some 3D IPN microstructures exhibit fully elastic behavior. Our funding encourages the further development of IPN systems as versatile and easily tunable MPL materials. T2 - Micro Nano Engineering (MNE conference) CY - Berlin, Germany DA - 25.09.2023 KW - Interpenetrating polymer network KW - Multiphoton Lithography KW - Two photon polymerisation KW - Direct laser writing KW - Polyethylene glycol diacrylate PY - 2023 AN - OPUS4-58879 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Pauw, Brian Richard A1 - Smales, Glen Jacob T1 - Raw and processed X-ray scattering datasets for: "Entering a new dimension in powder processing for advanced ceramics shaping" N2 - This dataset is a complete set of raw, processed and analyzed data, associated with the manuscript mentioned in the title. All associated metadata and processing history has been added. Particle size distribution analyses using McSAS are included as well. The samples consisted of a 4.2 mass% dispersion of yttria-stabilized zirconia nanoparticles in a cross-linked matrix. The measurements show a good dispersion with minimal agglomeration. The wide-angle region shows diffraction information consistent with zirconia. KW - X-ray scattering KW - Nanocomposite KW - Ceramic microprinting KW - Yttria-stabilized zirconia KW - SAXS KW - Nanomaterials KW - Two-photon polymerization KW - Transparency KW - Mechanical testing PY - 2023 DO - https://doi.org/10.5281/zenodo.7498647 PB - Zenodo CY - Geneva AN - OPUS4-56766 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Fritzsche, Sven A1 - Pauw, Brian Richard A1 - Weimann, Christiane A1 - Sturm, Heinz T1 - Test artifact for fs-LDW N2 - Data to generate the given graphs in the publication as well as raw images of the shown images. KW - stl code KW - Images KW - Graphs KW - Data PY - 2023 DO - https://doi.org/10.5281/zenodo.7671945 PB - Zenodo CY - Geneva AN - OPUS4-58096 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Zarinwall, A. A1 - Waniek, Tassilo A1 - Finke, B. A1 - Sadaat, R. A1 - Sturm, Heinz A1 - Garnweitner, G. ED - Sinapius, M. ED - Ziegmann, G. T1 - Particle Surface Modification N2 - Whilst a decisive role of the particle-matrix interphase on the mechanical properties of nanoparticle-filled polymers has been demonstrated in the last years, the arbitrary design of this interphase remains a very challenging goal. In principle, this could be realized via an appropriate surfacemodification of the nanofiller prior to its incorporation in the polymer. For most systems, such as for boehmite nanofillers, however, the interaction of organic modifiers with the particle surface has not been studied in detail, and only single studies are known rather than systematic investiga- tions on the effects of different chemical functions anchored on the particle surface. In this chapter, we present an extensive study on the binding of APTES, a common silane surface modifier, with boehmite, and show that thermogravimetric analysis (TGA) coupled with mass spectrometry (MS) is a convenient and highly suitable method to elucidate the ligand binding in detail. Furthermore, a two-step coupling strategy is presented, demonstrating that based on APTES anchored to the parti- cle surface, the condensation of various carboxylic acids can be utilized to enable highly diverse chemical properties of the nanofillers, which leads to very different particle-matrix interactions in the nanocomposites. KW - APTES KW - Boehmite KW - Nanoparticle KW - TGA-MS PY - 2021 SN - 978-3-030-68522-5 SN - 978-3-030-68523-2 DO - https://doi.org/10.1007/978-3-030-68523-2 SN - 2194-8240 SN - 2194-8259 SP - 119 EP - 142 PB - Springer Nature Switzerland AG CY - Cham AN - OPUS4-53727 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Cano Murillo, Natalia A1 - Szymoniak, Paulina A1 - Smales, Glen Jacob A1 - Sturm, Heinz A1 - Schönhals, Andreas T1 - Electrospun nanocomposites fibers of polycarbonate and taurine modified boehmite nanoparticles - What can be learned from structural and thermal investigations N2 - Though the reinforcing properties of inorganic particles in thermosetting nanocomposites, has been exploited, the integration of nanoparticles continues to be challenging in terms of their homogeneous distribution and their manipulation which can contribute to occupational hazards. Due to a second encapsulations of nanoparticles, electrospun nanocomposite fibers containing nanoparticles might be an alternative for overcoming these issues, as the fiber nonwovens contains the nanoparticles allowing for safer manipulation. Here, the morphology, and the thermal properties of electrospun polycarbonate fibers containing taurine modified boehmite nanoparticles (BNP) are investigated by means of small and wide-angle X-ray scattering as well as fast scanning and temperature modulated fast scanning calorimetry for the first time. The latter techniques allow the investigation of the thermal properties of single fibers at heating rates up to 10^4 K s^-1 keeping its structure intact. A quantitative analysis of the scattering data reveals a porous structure of the fibers. The porous structure is quantified regarding the pore volume and the pore size. A constant amount of aggregation is found even for the highly BNP loaded fibers. Thermal analysis on the fibers reveals a rigid amorphous fraction (RAF) where it is known that RAF determinates the properties of a nanocomposite to a large extent. For the fibers RAF amounts up to 40 wt%, which is essential higher compared to equally formulated PC/BNP composite cast films. The RAF in the case of the fibers, is not only due to the presence of particles in the polymer but also due to orientation effects induced by the electrospinning process. KW - Nanocomposite fibers KW - Electrospinning KW - X-ray scattering KW - Fast scanning calorimetry KW - Rigid amorphous fraction PY - 2021 DO - https://doi.org/10.1021/acsapm.1c01265 VL - 3 IS - 12 SP - 6572 EP - 6585 PB - ACS AN - OPUS4-53871 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Szymoniak, Paulina A1 - Qu, Xintong A1 - Schönhals, Andreas A1 - Sturm, Heinz ED - Sinapius, M. ED - Ziegmann, G. T1 - Characterization of Polymer Nanocomposites N2 - The complex effect of nanoparticles on an epoxy-based and anhydride cured DGEBA/Boehmite nanocomposite with different particle concentrations is considered in this chapter. A combination of X-ray scattering, calorimetry (fast scanning and temperature modulated calorimetry) and dielectric spectroscopy was employed to characterize the structure, vitrification kinetics and the molecular dynamics of the nanocomposites. Firstly, the unfilled polymer was found to be intrinsically heterogeneous, showing regions with different crosslinking density, indicated by two separate dynamic glass transitions. Moreover, the glass transition temperature decreases with increasing nanoparticle concentration, as a result of changes in the crosslinking density. In addition, it was shown that the incorporation of nanoparticles can result in simultaneous increase in the number of mobile segments for low nanoparticle concentrations and on the other hand, for higher loading degrees the number of mobile segments decreases, due to the formation of an immobilized interphase. KW - Rigid amorphous fraction KW - Epoxy nanocomposites KW - X-ray scattering KW - Differential scanning calorimetry KW - Broadband dielectric spectroscopy KW - Flash DSC PY - 2021 DO - https://doi.org/10.1007/978-3-030-68523-2_4 SP - 55 EP - 77 PB - Springer Nature AN - OPUS4-52698 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zarinwall, A. A1 - Waniek, Tassilo A1 - Saadat, R. A1 - Braun, U. A1 - Sturm, Heinz A1 - Garnweitner, G. T1 - Comprehensive Characterization of APTES Surface Modifications of Hydrous Boehmite Nanoparticles N2 - Hydrous boehmite (γ-AlOOH) nanoparticles (BNP) show great potential as nanoscale filler for the fabrication of fiber reinforced nanocomposite materials. Notably, the particle−matrix interaction has been demonstrated to be decisive for improving the matrix-dominant mechanical properties in the past years. Tailoring the surface properties of the nanofiller enables to selectively design the interaction and thus to exploit the benefits of the nanocomposite in an optimal way. Here, an extensive study is presented on the binding of (3-aminopropyl)triethoxysilane (APTES), a common silane surface modifier, on BNP in correlation to different process parameters (concentration, time, temperature, and pH). Furthermore, a comprehensive characterization of the modified BNP was performed by using elemental analysis (EA), thermogravimetric analysis (TGA) coupled with mass spectrometry (TGA-MS), and Kaiser’s test (KT). The results show an increasing monolayer formation up to a complete surface coverage with rising APTES concentration, time, and temperature, resulting in a maximal grafting density of 1.3 molecules/nm². Unspecific multilayer formation was solely observed under acidic conditions. Comparison of TGA-MS results with data recorded from EA, TGA, and KT verified that TGA-MS is a convenient and highly suitable method to elucidate the ligand binding in detail. KW - Boehmite KW - Nanoparticle KW - Surface KW - APTES KW - Functionalization KW - BET KW - TGA KW - Grafting KW - Nanocomposite KW - Silane PY - 2020 DO - https://doi.org/10.1021/acs.langmuir.0c02682 VL - 37 IS - 1 SP - 171 EP - 179 PB - ACS Publications AN - OPUS4-51954 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Madbouly, Loay Akmal T1 - Chemical analysis of commercial functionalized graphene along the production process N2 - Graphene has found widespread commercial use, particularly in flexible electronics and coatings for substrates such as paper and textiles, in the form of suspensions and inks (Zhang et al., 2017). Functionalization of graphene allows fine-tuning of properties like electrical conductivity. Structural and chemical features of graphene materials are typically analyzed by Raman spectroscopy and X-ray photoelectron spectroscopy (XPS). While Raman spectroscopy plays a critical role in identifying the presence of graphene and characterizing its structural defects (Pollard et al., 2017), XPS examines the chemistry of graphene. This study investigates three types of graphene materials — graphene (unfunctionalized, G-graphene), fluorine-functionalized graphene (F-graphene), and nitrogen-functionalized graphene (N-graphene) — across three physical forms: powders, suspensions, and embedded in inks. Functionalization was performed via plasma treatment of G-graphene with fluorine or ammonia gases. Suspensions were obtained by dispersing powders in distilled water, while inks were formulated using diacetone alcohol, carbon black, and graphene. Raman spectroscopy analysis confirmed the graphitic nature of all materials and revealed differences in defect density across different forms. The characteristic D, G, and D’ bands varied in relative intensity, offering insight into structural integrity and functionalization effects. XPS measurements examined core-level spectra (C 1s, F 1s, N 1s), revealing chemical bonding environments and hybridization states, including the sp² and sp³ states. A notable decline in fluorine content in F-graphene suspensions and inks, relative to powders, was observed. Existence of organic fluorine and total absence of metallic fluorine were observed. Raman spectroscopy and XPS data provided a correlated view of structural and chemical evolution through the graphene production chain (Figure 1). T2 - RamanFest 2025 CY - Frankfurt, Germany DA - 02.07.2025 KW - Functionalized graphene KW - Graphene-related 2D materials (GR2M) KW - Raman Spectroscopy KW - XPS KW - Inks PY - 2025 AN - OPUS4-64114 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Madbouly, Loay Akmal T1 - Raman Spectroscopy and X-ray Photoelectron Spectroscopy of Commercial Functionalized Graphene N2 - Graphene has been commercialized for over a decade. For many applications like flexible electronics, coating of different materials like paper or for textiles, it used in the form of suspensions or inks [1]. Graphene powders are typically used as the starting material for the synthesize of graphene suspensions and graphene inks. Functionalization enables tailoring the properties of graphene, such as the sheet resistance. X-ray photoelectron spectroscopy (XPS), Raman spectroscopy, along other techniques are used to characterize graphene flakes, functionalized and otherwise. Raman spectroscopy is necessary as a primary step to validate the existence of graphene structure in graphene powders [2]. XPS is commonly used to investigate the elemental composition, including impurities, and the chemical structure of graphene. In this study, we investigate the following set of commercial materials: fluorine-functionalized graphene (F-graphene) and nitrogen-functionalized graphene (N-graphene) as well as unfunctionalized graphene (G-graphene) in the forms of powders, suspensions, and inks. The functionalization process for the graphene powder was carried out in a plasma reactor by purging fluorine and ammonia gases, in separate processes, over the G-graphene powder. The suspensions were prepared by adding distilled water to the powders. The inks consist of diacetone alcohol, carbon black, and graphene powders. Raman spectroscopy and XPS are complementary techniques. Our results obtained from Raman spectroscopy confirmed the existence of graphene structures in all samples and provided a comparative insight on the structural defects between samples. XPS was used to investigate the chemical states of elements in graphene, such as sp2 and sp3 hybridization states of carbon, as well as the chemical effect of functionalization on graphene. High resolution XPS analysis was performed for C 1s, F 1s and N 1s core-levels for all the graphene samples: G-graphene, F-graphene, and N-graphene, in all forms. The XPS results showed the elemental composition and the impurities of each sample. All powders showed less presence of carboxyl groups, compared to their respective suspensions and inks. F-functionalized suspension and inks showed a significant decrease in the at% of fluorine relative to the powder. These valuable insights, independent and when correlated, allowed the tracking of the structural and chemical changes of graphene along its production process. T2 - E-MRS 2025 CY - Strasbough, France DA - 26.05.2025 KW - Functionalized graphene inks PY - 2025 AN - OPUS4-64113 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Habibimarkani, Heydar A1 - Abram, Sarah-Luise A1 - de Oliveira Guilherme Buzanich, Ana A1 - Prinz, Carsten A1 - Sahre, Mario A1 - Hodoroaba, Vasile-Dan A1 - Radnik, Jörg T1 - In-depth analysis of FeNi-based nanoparticles for the oxygen evolution reaction N2 - This study investigates the effect of varying iron-to-nickel ratios on the catalytic performance of Fe-Ni oxide nanoparticles (NPs) for the oxygen evolution reaction (OER). Addressing the issue of high energy wastage due to large overpotentials in OER, we synthesized and characterized different NP catalysts with different Fe: Ni oxide ratios. Transmission Electron Microscopy (TEM), Energy Dispersive X-ray Spectroscopy (EDS), and X-ray Diffraction (XRD) were employed to determine the morphology, elemental and phase composition of the NPs. Furthermore, in-depth profiling with X-ray Photoelectron Spectroscopy (XPS) and Hard X-ray Photoelectron Spectroscopy (HAXPES) revealed that iron predominantly exists as oxide, while nickel exhibits both metallic and oxidic forms depending on the Fe content. XPS indicated an enrichment of iron at the NP surface, whereas HAXPES and EDS data agreed on the bulk stoichiometry. The assessment of the catalytic activity via cyclic voltammetry (CV) showed that the Fe: Ni ratio of 2:3 exhibited superior performance, characterized by lower overpotential and a smaller Tafel slope. KW - Fe-Ni oxide KW - Nanoparticles KW - OER KW - Catalytic performance KW - Cyclic voltammetry PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-626932 UR - https://www.nature.com/articles/s41598-025-92720-3 DO - https://doi.org/10.1038/s41598-025-92720-3 VL - 15 IS - 1 SP - 1 EP - 17 PB - Springer Nature AN - OPUS4-62693 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -