TY - CONF A1 - Schmitt, Johannes T1 - Data Acquisition System for Single Particle Inductively Coupled Plasma Mass Spectrometry (spICP-MS) with Nanosecond Time Resolution N2 - This study presents our data acquisition system prototype for spICP-MS with nanosecond time resolution (nanoDAQ) and a matching data processing approach for nanosecond resolved single particle spICP-MS data. The system continuously samples the secondary electron multiplier (SEM) detector signal with a dwell time of approximately 2 ns and enables the detection of gold nanoparticles (AuNP) as small as 7.5 nm[1] with a commercial single quadrupole ICP-MS instrument. The acquired transient data is processed based on the temporal distance between detector events and the event density. It was shown that the inverse logarithm of the distance between detector events is proportional to the particle size and that the number of detector events corresponding to a particle signal distribution can be used to calibrate and determine the particle number concentration (PNC) of a nanoparticle dispersion.[1] The high data acquisition frequency of the systems allows recording of a statistically significant number of data points in 60 s or less, which leads to the main time limitation for analyses being merely the sample uptake time and rinsing step between analyte solutions. T2 - 55th Annual Conference of the German Society for Mass Spectrometry CY - Freising, Germany DA - 10.03.2024 KW - Nanoparticles KW - Mass Spectrometry KW - Instrumentation KW - spICP-MS PY - 2024 AN - OPUS4-62315 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heinelt, Manuel T1 - Capabilities of Surface-Assisted Flowing Atmospheric-Pressure Afterglow Mass Spectrometry (SA-FAPA-MS) for Direct Analysis of Polycyclic Aromatic Hydrocarbons (PAHs) N2 - Ambient desorption/ionization mass spectrometry (ADI-MS) is a growing area in the analytical chemistry of organic molecules. It requires only minimal sample preparation and can reduce analysis time compared to traditional methods.[1] One evolving method is the plasma-based pin-to-capillary Flowing Atmospheric-Pressure Afterglow (FAPA) source. Which is an improved version of the original pin-to-plate FAPA, resulting in significantly lower background signals and less oxidation of the analytes.[2] In our case, samples are probed directly from thin-layer chromatography (TLC) plates, which have shown promising results in improving signal response and performance in mass spectral imaging in previous studies. Especially, cyano (CN)-HPTLC and reversed-phase (RP2)-TLC plates were suited best for the analysis of different organic molecules.[3] In this work, FAPA is investigated as a method to determine polycyclic aromatic hydrocarbons (PAHs). Furthermore, its suitability for rapid screening of real samples was investigated. 30 pure PAH standard samples were analyzed on different TLC surfaces. Cyano (CN)-HPTLC and reversed-phase (RP2)-TLC plates proved to be the most suitable substrate for the analysis of PAH compounds. Linear ranges of up to four orders of magnitude could be achieved. Limits of detection (LOD) of anthracene, chrysene, and fluorene were in the µg/L range. However, these pure analytes differ from PAH samples collected in the environment, which may contain hundreds of different PAHs among other constituents. Therefore, PAH containing real samples were used to test the method and its screening capability on more complex samples. A standard reference material (diesel particulate extract, NIST SRM 1975) was analyzed for method validation. For sample preparation, 1 µL of the extract was spotted directly onto the TLC surface. It was possible to perform a triple determination in approx. 20 min. Therefore, SA-FAPA-MS has a huge potential to be established as a method for rapid qualitative screening of PAHs in real samples. T2 - 55th Annual Conference of the German Society for Mass Spectrometry (Deutsche Gesellschaft für Massenspektrometrie, DGMS). CY - Freising, Germany DA - 10.03.2024 KW - Mass Spectrometry KW - Massenspektrometrie KW - Instrumental Analytical Chemistry KW - Instrumentelle Analytische Chemie KW - Polycyclic Aromatic Hydrocarbons PY - 2024 AN - OPUS4-62316 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmitt, Johannes T1 - Data acquisition system for single particle inductively coupled plasma mass spectrometry (spICP-MS) with nanosecond time resolution N2 - This study presents our data acquisition system prototype for single particle inductively coupled plasma mass spectrometry (spICP-MS) with nanosecond time resolution (nanoDAQ) and a matching data processing approach for time-resolved data in the nanosecond range. The system continuously samples the secondary electron multiplier (SEM) detector signal with a dwell time of approximately 2 ns and enables detection of gold nanoparticles (AuNP) as small as 7.5 nm with a commercial single quadrupole ICP-MS instrument. [1] Analysis of acquired transient data is based on the temporal distance between detector events and a derived ion event density. It was shown that the inverse logarithm of the distance between detector events is proportional to particle size. Also, the number of detector events per particle can be used to calibrate and determine the particle number concentration (PNC) of a nanoparticle dispersion. Particle-by-particle-based analysis of ion event density and other parameters derived from nanosecond time resolution show promising results. High data acquisition frequency of the systems allows recording of a statistically significant number of data points in 60 s or less, which leaves only the sample uptake and rinsing steps as remaining factors for limiting the total measurement time. T2 - 20th European Winter Conference on Plasma Spectrochemistry CY - Berlin, Germany DA - 02.03.2025 KW - ICP-MS KW - Instrumentation KW - Nano KW - Nanoparticle Characterization PY - 2025 AN - OPUS4-63599 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ruehle, Bastian T1 - Nano- and Advanced Materials Synthesis in a Self-Driving Lab (SDL) N2 - Nano- and advanced materials have been recognized as a key enabling technology of the 21st century, due to their high potential of driving innovations in new clean energy technologies, sustainable manufacturing by substitution of critical raw materials and replacement of hazardous substances, breakthroughs in energy conversion and storage, improvement of the environmental performance of products and processes, and facilitation of circularity. Consequently, improving tools that enhance the development and optimization cycle of nano- and advanced materials is crucial. In this contribution, we present our Self-Driving Lab (SDL) for Nano and Advanced Materials [1], that integrates robotics for batched autonomous synthesis – from molecular precursors to fully purified nanomaterials – with automated characterization and data analysis, for a complete and reliable nanomaterial synthesis workflow. By fully automating these three process steps for seven different materials from five representative, completely different classes of nano- and advanced materials (metal, metal oxide, silica, metal organic framework, and core–shell particles) that follow different reaction mechanisms, we demonstrate the great versatility and flexibility of the platform. The system also exhibits high modularity and adaptability in terms of reaction scales and incorporates in-line characterization measurement of hydrodynamic diameter, zeta potential, and optical properties (absorbance, fluorescence) of the nanomaterials. We discuss the excellent reproducibility of the various materials synthesized on the platform in terms of particle size and size distribution, and the adaptability and modularity that allows access to a diverse set of nanomaterial classes. These features underscore the SDL’s potential as a transformative tool for advancing and accelerating the development of nano- and advanced materials, offering solutions for a sustainable and environmentally responsible future. T2 - Accelerate 2025 CY - Toronto, Canada DA - 11.08.2025 KW - Nanomaterials KW - Advanced Materials KW - Automation KW - SDL KW - MAP PY - 2025 AN - OPUS4-63935 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Escobar-Carranza, Cristian C. T1 - On the Detection of Microplastics by Flowing Atmospheric-Pressure Afterglow Mass Spectrometry (FAPA-MS) N2 - Microplastics (MPs) are widespread pollutant particles that can be analyzed using Raman and FTIR spectroscopy combined with optical microscopy. Additionally, pyrolysis (Py) or thermal extraction and desorption (TED) coupled with gas chromatography-mass spectrometry (GC-MS) are used for the characterization of MPs.[1] However, sample throughput is limited due to GC separation. This work presents a feasibility study for the direct, rapid analysis of MPs using high-resolution mass spectrometry and a plasma-based ambient desorption/ionization source (FAPA, flowing atmospheric-pressure afterglow).[2] In earlier work, an in-house built ambient ionization source (modelled after the pin-to-capillary (p2c) FAPA design by Shelley et al. [3]) was coupled to HR-Orbitrap MS and used to characterize different MPs produced in-house from plastic materials including polystyrene (PS), polypropylene (PP), low-density polyethylene (LDPE), and polycarbonate (PC). Simultaneous detection of characteristic ions and particle imaging on a sampling mesh was feasible, with detection limits (LOD) for PS MPs at 311 µm in size and 1.3 mg in mass. Principal component analysis (PCA) was used for particle differentiation. This work presents an improved desorption/ionization approach using higher temperatures for desorption enhancement (approximately 500 °C, achieved with economical and commercially available parts) and a tailored source housing combined with a halo-shaped (h-FAPA) source configuration.[4] The scope was expanded to include MPs from poly(ethylene terephthalate) (PET), poly(methyl methacrylate) (PMMA), and poly(vinyl chloride) (PVC), sized 125–250 µm. Data visualization and interpretation were performed using Kendrick mass defect plots and other multivariate analysis tools. Compared to earlier results, h-FAPA-MS yielded at least 65% higher ion signals for selected ions in all MPs. These ions were detected mainly as protonated species [M+H]+. Higher thermal desorption temperatures aided in detecting all MPs, as the presence of higher molecular weight fragments added specificity to the analysis. Notably, experiments with the h-FAPA source demonstrated lower mass-based LODs for MPs than the p2c-FAPA source (e.g., 14 µg vs 1.3 mg for PS, respectively). T2 - ANAKON 2025 CY - Leipzig, Germany DA - 10.03.2025 KW - Mass Spectrometry KW - Plasma KW - FAPA-MS KW - Microplastics PY - 2025 AN - OPUS4-63604 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schütz, Désirée A.-M. T1 - Feasibility Study on the Adsorption of Environmental Contaminants onto Fresh and Aged Microplastics N2 - Microplastics (MPs) refer to plastic particles, fibers, or beads with sizes ranging from 100 nm to 5 mm in size. Their pervasive distribution as environmental contaminants have escalated into a significant global concern. Primary MPs are intentionally produced particles for industrial and commercial applications, such as exfoliants in personal care and cosmetic formulations. In contrast, secondary MPs are generated through the fragmentation and degradation of larger plastic materials, due to environmental weathering processes. [1] Due to their high surface area-to-volume ratio and hydrophobic nature, MPs have the potential to serve as vectors for the accumulation and transport of diverse organic contaminants, including polycyclic aromatic hydrocarbons (PAHs), perfluoroalkyl substances (PFAS), pharmaceuticals and personal care products (PPCPs), as well as trace metals such as silver, cadmium, chromium, and copper. In the environmental, MPs are subject to aging processes driven by factors such as temperature, ultraviolet radiation, oxygen, and chemical interactions with environmental toxins. This aging can induce significant alterations in their physicochemical properties, which, in turn, can affect the adsorption behavior. [2] Classical and alternative analytical methods such as high-performance liquid chromatography (HPLC) and ambient desorption/ionization high-resolution mass spectrometry (ADI-HR-MS) can help to study the adsorption potential. ADI-HR-MS allows rapid sample analysis with minimal preparation, providing results in under a minute, much faster than traditional chromatographic techniques. [3] This study aims to investigate the influence of aging and particle size on the ability of microplastics to act as vectors for environmental contaminants. Microplastics were prepared in-house and subjected to controlled aging conditions for 12, 24, 36, and 48 hours. Subsequently, the aged MPs were exposed in plastic-free containers to model solutions to simulate co-contaminants in the environment. Adsorption onto synthesized secondary microplastics, varying in size and aging status, was investigated at different time intervals with ambient MS and time-of-flight secondary ion mass spectrometry. T2 - ANAKON 2025 CY - Leipzig, Germany DA - 10.03.2025 KW - Mass Spectrometry KW - FAPA-MS KW - Microplastics KW - TOF-SIMS KW - Surface Analysis PY - 2025 AN - OPUS4-63606 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmitt, Johannes T1 - Data acquisition system for single particle inductively coupled plasma mass spectrometry (spICP-MS) with nanosecond time resolution N2 - This study presents our data acquisition system prototype for single particle inductively coupled plasma mass spectrometry (spICP-MS) with nanosecond time resolution (nanoDAQ) and a matching data processing approach for time-resolved data in the nanosecond range. The system continuously samples the secondary electron multiplier (SEM) detector signal with a dwell time of approximately 2 ns and enables detection of gold nanoparticles (AuNP) as small as 7.5 nm with a commercial single quadrupole ICP-MS instrument. [1] Analysis of acquired transient data is based on the temporal distance between detector events and a derived ion event density. It was shown that the inverse logarithm of the distance between detector events is proportional to particle size. Also, the number of detector events per particle can be used to calibrate and determine the particle number concentration (PNC) of a nanoparticle dispersion. [1] Particle-by-particle-based analysis of ion event density and other parameters derived from nanosecond time resolution show promising results. High data acquisition frequency of the systems allows recording of a statistically significant number of data points in 60 s or less, which leaves only the sample uptake and rinsing steps as remaining factors for limiting the total measurement time. T2 - ANAKON 2025 CY - Leipzig, Germany DA - 10.03.2025 KW - ICP-MS KW - Instrumentation KW - Nano KW - Nanoparticle Characterization PY - 2025 AN - OPUS4-63603 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heinelt, Manuel T1 - Feasibility Study on the Direct Detection of Per- and Polyfluoroalkyl Substances (PFAS) with Surface-Assisted Flowing Atmospheric-Pressure Afterglow Mass Spectrometry (SA-FAPA-MS) N2 - Per- and polyfluoroalkyl substances (PFAS) are a large class of thousands of synthetic chemicals that are used worldwide. However, growing environmental and human health concerns in the last two decades have led to more stringent regulatory requirements and the development of quantitative analytical methods for PFAS detection. Today, standardized and powerful methods exist, e.g., for the determination of PFAS in water, sludge, compost, soil, and drinking water (DIN 38407-42, DIN 38414-14, ISO 21675, and DIN EN 17892). While liquid chromatography coupled to tandem mass spectrometry (LC-MS/MS) is often used, blank levels, sample preparation, and total analysis times can be challenging. [1] Here, ambient desorption/ionization mass spectrometry (ADI-MS) is considered interesting because it requires only minimal sample preparation and was able to reduce total analysis time in other types of applications. [2] Previously, we used a plasma-based pin-to-capillary flowing atmospheric-pressure afterglow source (FAPA) [3] to probe samples directly from thin-layer chromatography (TLC) plates and to perform quantitative analysis and mass spectral imaging [4]. In this work, a feasibility study for the direct detection of PFAS with FAPA-MS is reported. Selected PFAS samples were directly probed on functionalized TLC surfaces (normal-phase silica, reversed-phase-modified silica, cyano [CN]-modified silica, and dimethyl [RP2]-modified silica, diol modified silica, and amino [NH2]-modified silica). The suitability of the surfaces was evaluated and the compatibility of different solvents with the surfaces was studied. CN-HPTLC and RP2-TLC surfaces showed the best performance for direct PFAS detection with FAPA-MS. In addition, direct analysis of PFAS mixtures and selected matrices was performed with little sample preparation and short analysis time. T2 - ANAKON 2025 CY - Leipzig, Germany DA - 10.03.2025 KW - Mass Spectrometry KW - FAPA-MS KW - Instrumentation KW - PFAS KW - Surface Analysis PY - 2025 AN - OPUS4-63605 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heinelt, Manuel T1 - Feasibility Study on the Direct Detection of Per- and Polyfluoroalkyl Substances (PFAS) with Surface-Assisted Flowing Atmospheric-Pressure Afterglow Mass Spectrometry (SA-FAPA-MS) N2 - Per- and polyfluoroalkyl substances (PFAS) are a large class of thousands of synthetic chemicals that are used worldwide. However, growing environmental and human health concerns in the last two decades have led to more stringent regulatory requirements and the development of quantitative analytical methods for PFAS detection. Today, standardized and powerful methods exist, e.g., for the determination of PFAS in water, sludge, compost, soil, and drinking water (DIN 38407-42, DIN 38414-14, ISO 21675, and DIN EN 17892). While liquid chromatography coupled to tandem mass spectrometry (LC-MS/MS) is often used, blank levels, sample preparation, and total analysis times can be challenging. [1] Here, ambient desorption/ionization mass spectrometry (ADI-MS) is considered interesting because it requires only minimal sample preparation and was able to reduce total analysis time in other types of applications. [2] Previously, we used a plasma-based pin-to-capillary flowing atmospheric-pressure afterglow source (FAPA) [3] to probe samples directly from thin-layer chromatography (TLC) plates and to perform quantitative analysis and mass spectral imaging [4]. In this work, a feasibility study for the direct detection of PFAS with FAPA-MS is reported. Selected PFAS samples were directly probed on functionalized TLC surfaces (normal-phase silica, reversed-phase-modified silica, cyano [CN]-modified silica, and dimethyl [RP2]-modified silica, diol modified silica, and amino [NH2]-modified silica). The suitability of the surfaces was evaluated and the compatibility of different solvents with the surfaces was studied. CN-HPTLC and RP2-TLC surfaces showed the best performance for direct PFAS detection with FAPA-MS. In addition, direct analysis of PFAS mixtures and selected matrices was performed with little sample preparation and short analysis time. T2 - 56th Annual Conference of the DGMS CY - Göttingen, Germany DA - 04.03.2025 KW - FAPA-MS KW - Instrumentation KW - Mass Spectrometry KW - PFAS KW - Surface Analysis PY - 2025 AN - OPUS4-63643 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schütz, Désirée A.-M. T1 - Feasibility Study on the Adsorption of Environmental Contaminants onto Fresh and Aged Microplastics N2 - Microplastics (MPs) refer to plastic particles, fibers, or beads with sizes ranging from 100 nm to 5 mm in size. Their pervasive distribution as environmental contaminants have escalated into a significant global concern. Primary MPs are intentionally produced particles for industrial and commercial applications, such as exfoliants in personal care and cosmetic formulations. In contrast, secondary MPs are generated through the fragmentation and degradation of larger plastic materials, due to environmental weathering processes. [1] Due to their high surface area-to-volume ratio and hydrophobic nature, MPs have the potential to serve as vectors for the accumulation and transport of diverse organic contaminants, including polycyclic aromatic hydrocarbons (PAHs), perfluoroalkyl substances (PFAS), pharmaceuticals and personal care products (PPCPs), as well as trace metals such as silver, cadmium, chromium, and copper. In the environmental, MPs are subject to aging processes driven by factors such as temperature, ultraviolet radiation, oxygen, and chemical interactions with environmental toxins. This aging can induce significant alterations in their physicochemical properties, which, in turn, can affect the adsorption behavior. [2] Classical and alternative analytical methods such as high-performance liquid chromatography (HPLC) and ambient desorption/ionization high-resolution mass spectrometry (ADI-HR-MS) can help to study the adsorption potential. ADI-HR-MS allows rapid sample analysis with minimal preparation, providing results in under a minute, much faster than traditional chromatographic techniques. [3] This study aims to investigate the influence of aging and particle size on the ability of microplastics to act as vectors for environmental contaminants. Microplastics were prepared in-house and subjected to controlled aging conditions for 12, 24, 36, and 48 hours. Subsequently, the aged MPs were exposed in plastic-free containers to model solutions to simulate co-contaminants in the environment. Adsorption onto synthesized secondary microplastics, varying in size and aging status, was investigated at different time intervals with ambient MS and time-of-flight secondary ion mass spectrometry. T2 - 56th Annual Conference of the DGMS CY - Göttingen, Germany DA - 04.03.2025 KW - FAPA-MS KW - Mass Spectrometry KW - Microplastics KW - Surface Analysis KW - TOF-SIMS PY - 2025 AN - OPUS4-63644 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Oskoei, Parastu T1 - Thermoresponsive UCNP@MSN Nanoparticles for Doxorubicin Delivery in Melanoma Cells N2 - Upconversion nanoparticles (UCNPs) possess unique photophysical characteristics, such as excita bility by near infrared (NIR) light, which facilitates deep tissue penetration, multi color emission , long luminescence lifetimes, and an excellent photostability. These features have made UCNPs promising tools for biomedical applications . M esoporous silica nanoparticles (MSNs) functionalized with stimuli responsive nanovalves or specific coatings enable the encapsulation and controlled release of therapeutic agen ts, thereby offering spatiotemporal precision in drug delivery 1 3 ]]. Among drug delivery strategies, photoresponsive systems have attracted growing attention due to their potential for clinical applications . This is especially relevant for melanoma, an aggressive skin cancer with increasing global incidence, for which conventional therapeutic modalities remain largely insufficient in advanced stage 4 In this work, core shell UCNP@MSN nanoparticles were synthetised by coating UCNPs with a mesoporous silica layer, which was subsequently functionalized with thermoresponsive retro Diels Alder nanovalves [ and loaded with the chemotherapeutic agent doxorubicin (DOX). Controlled drug release was effectively achieved under 980 nm NIR i llumination . Treatment with functionalized nanoparticles significantly reduced the viability of melanoma cell lines, with an enhanced cytotoxicity being observed upon combined nanoparticle exposure and NIR illumination . Mechanistic analyses revealed that neither UCNPs nor NIR i llumination alone could induce the production of reactive oxygen species (ROS); however, their combination induced a marked increase in ROS levels in two of the three tested cell lines. Furthermore, this dual treatment promoted substantial apoptotic and/or necrotic responses across all cell models. These findings underscore the potential of UCNP@MSN nanoplatforms, equipped with thermoresponsive ga tes , as efficient photoactivated drug delivery systems for melanoma therapy. T2 - Conference Jornadas CICECO CY - Aveiro, Portugal DA - 09.10.2025 KW - Nano KW - Particle KW - Lanthanide KW - Upconversion KW - Surface chemistry KW - Mesoporous silica KW - Doxorubicin KW - Nanomedicine KW - Triggered release KW - pH KW - Cellular uptake KW - Toxicity KW - Folate KW - Ligand PY - 2025 AN - OPUS4-64371 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Oskoei, Párástu T1 - Cell mechanisms induced by doxorubicin-loaded UCNP@MSN nanoparticles with a thermosresponsive nanovalve in melanoma cells N2 - Upconversion nanoparticles (UCNPs) exhibit several remarkable optical properties, including excitation by near infrared (NIR) light, which enables deep tissue penetration, multiple distinct emission bands across a wide range of wavelengths, long luminescen ce lifetimes, and high photostability. These features make them particularly attractive for various biomedical applications. Mesoporous silica nanoparticles (MSNs), functionalized with nanovalves or specific coatings, have been explored for controlled and targeted drug delivery, where therapeutic agents are encapsulated within the nanopores, allowing spatiotemporal release 1 3 ]]. Among the promising approaches, photoactivated drug delivery systems have drawn considerable interest due to their versatility and potential. One relevant application is in the treatment of melanoma, an aggressive form of skin cancer with a rising global incidence. In advanced stages, conventional therapies often fail to achieve complete tumour eradication, resulting in poor prognose s 4 In this study, UCNPs were coated with a mesoporous silica shell to form core shell UCNP@MSN nanoparticles, which were further functionalized with thermoresponsive retro Diels Alder nanovalves and loaded with doxorubicin (DOX), a chemotherapeutic drug used in melanoma treatment. Upon exposure to 980 nm NIR light, DOX release was successfully triggered in the culture medium. Exposure to functionalized UCNPs decreased the viability of the tested melanoma cell lines, with further reductions observed when the ex posure to the nanoparticles was combined with irradiation. Subsequently, t he toxicity mechanisms were evaluated and showed that w hile individual treatments with either the functionalized UCNPs or NIR irradiation alone had no effect on reactive oxygen species (ROS) production, their combination significantly increased ROS levels in two of the three tested cell lines. This combined treatment also led to notable increases in apoptotic , necrotic or both type of cells’ percentages on all cell lines. Overall, these findings highlight the potential of these nanoparticles with thermoresponsive gating mechanisms as effective platforms for targeted drug delivery in melanoma therapy. T2 - EUROTOX 2025 CY - Athens, Greece DA - 14.09.2025 KW - Nano KW - Particle KW - Lanthanide KW - Upconversion KW - Surface chemistry KW - Mesoporous silica KW - Doxorubicin KW - Nanomedicine KW - Triggered release KW - pH KW - Cellular uptake KW - Toxicity KW - Folate KW - Ligand PY - 2025 AN - OPUS4-64372 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -