TY - JOUR A1 - Hanelt, Sven A1 - Friedrich, Jörg Florian A1 - Meyer-Plath, Asmus T1 - UV spectrometric indirect analysis of brominated MWCNTs with UV active thiols and an alkene-reaction kinetics, quantification and differentiation of adsorbed bromine and oxygen N2 - Indirect UV-absorption spectrometry was shown to be a valuable tool for chemical characterization of functionalized carbon nanotubes (CNTs). It complements data from X-ray photoelectron spectroscopy (XPS) or FTIR analysis since it helps to clarify the type and concentration of functional groups. The principles of indirect application of UV-spectrometry and its mathematical interpretation are discussed. Their facile application, together with their adequate sensitivity and high flexibility, make UV-absorption-based approaches a valuable alternative to fluorescence spectrometry. Here, the approach was applied to the chemical analysis of oxidizing substances on CNTs. For this, pristine CNTs of low but finite oxygen content as well as brominated CNTs were analyzed by reaction in suspension with UV-active thiol reagents and a styrene derivative. It was shown that carefully selected reagents allow differentiation and quantification of bromine and generally oxidizing entities like oxygen. For brominated CNTs, it was shown that physisorbed bromine may dominate the overall bromine content. KW - Carbon nanotubes KW - CNTs KW - UV-spectrometry KW - Bromination KW - Thiols KW - Mercaptans KW - Disulfides KW - Quantification KW - Kinetics PY - 2013 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-289077 DO - https://doi.org/10.3390/ma6083035 SN - 1996-1944 VL - 6 IS - 8 SP - 3035 EP - 3063 PB - MDPI CY - Basel AN - OPUS4-28907 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kupsch, Andreas A1 - Hentschel, Manfred P. A1 - Lange, Axel A1 - Müller, Bernd R. T1 - Röntgen-Interface-Radiographie im Dunkelfeld N2 - Es wird ein Verfahren zur Röntgenabbildung schwach absorbierender Objekte vorgestellt. Als kontrastgebender Effekt wird die Röntgenrefraktion an Ober- und Grenzflächen ausgenutzt. Zur Erzeugung eines sogenannten Dunkelfeldes wird ein schwach gekrümmter Transmissionskristall eingesetzt, der lokal, d.h. in einem kleinen Ausschnitt des Einstrahlquerschnitts, die Bragg-Bedingung erfüllt. Innerhalb dieser Zone erscheinen die durch Refraktion abgelenkten Strahlkomponenten als hell leuchtende Interface-Strukturen. Die Synthese mehrerer Dunkelfeldstreifen ergibt hochaufgelöste 2D Beispiel von biologischen und technischen Mikrostrukturen. T2 - DGZfP-Jahrestagung 2013 CY - Dresden, Germany DA - 06.05.2013 KW - Refraction enhanced imaging (REI) KW - Radiographie KW - Dunkelfeldabbildung KW - Röntgenrefraktion PY - 2013 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-286900 SN - 978-3-940283-49-8 IS - Di.3.C.1 SP - 1 EP - 7 PB - Deutsche Gesellschaft für zerstörungsfreie Prüfung e.V. (DGZfP) AN - OPUS4-28690 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krause, Martin A1 - Effner, Ute A1 - Müller, Sabine A1 - Nowak, Thomas Rudolf A1 - Vergin, Dirk T1 - 3D-SAFT Imaging von Streuern in Brettschichtholz N2 - Aktuell wird die Ultraschallechotechnik für Holzbauteile genutzt, indem aus der Abschattung eines ansonsten stabilen Rückwandechos auf Auffälligkeiten im Holzbauteil geschlossen wird. Dabei werden Transversalwellen (Mittenfrequenz 50 kHz) mit der Polarisationsrichtung in Faserrichtung (L) angewendet. In einem 2012 abgeschlossenen Forschungsvorhaben wurde nun die direkte Abbildung von Streuern durch anisotrope SAFT-Rekonstruktion entwickelt. Dazu werden flächig aufgenommene Ultraschallmessdaten mit automatisiert scannenden Druck- und Scherwellenköpfen erzeugt und auf Basis anisotroper Geschwindigkeitsverteilungen rekonstruiert. Benutzt werden die auch häufig für Beton eingesetzten trocken ankoppelnden Punktkontakt-Prüfköpfe. Da damit auch intensive Wellen an der Oberfläche erzeugt werden, entstehen im Material zusätzliche Kopfwellen, die ebenfalls bei der Rekonstruktion berücksichtigt werden. Da die Wellengeschwindigkeiten in Holz individuell stark schwanken, wird eine interaktive Auswertetechnik zur Ermittlung der Materialkonstanten benutzt. Für die Messungen werden Druckwellen sowie Scherwellen in zwei Polarisationsrichtungen verwendet. Die Messungen erfolgen sowohl mit automatischen Scannersystemen als auch mit einem linearen Prüfkopf-Array (kommerziell erhältlicher multistatischer Messkopf). Gezeigt werden Ergebnisse an Bauteilen mit künstlichen und realen Fehlstellen. Das Forschungsprojekt wurde gefördert vom Bundesamt für Bau- und Raumordnung (BBR, Zukunft Bau). T2 - DGZfP-Jahrestagung 2013 CY - Dresden, Germany DA - 06.05.2013 KW - Holz KW - Ultraschallecho KW - Anisotropie KW - Rekonstruktionsrechnung KW - Fehlstellenortung PY - 2013 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-293509 SN - 978-3-940283-49-8 IS - Poster 8 SP - 1 EP - 9 AN - OPUS4-29350 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krankenhagen, Rainer A1 - Groll, E.T. A1 - Kalisch, U. A1 - Maierhofer, Christiane A1 - Mecke, R. A1 - Meinhardt, J. A1 - Myrach, Philipp A1 - Schiller, M. A1 - Seidl, T. T1 - Untersuchung der Putzritzungen am Magdeburger Dom mit aktiver Thermografie und optischen 3D-Messverfahren N2 - Eines der bedeutendsten Kunstwerke des Magdeburger Doms sind die Putzritzungen am Ostflügel des Kreuzgangs aus dem 13. Jahrhundert. Der größte Teil der einzelnen Putzoberflächen sind Ausbesserungen oder Neuverputzungen aus verschiedenen Restaurierungs- oder Reparaturphasen. In dem von der Forschungsinitiative Zukunft Bau geförderten Projekt zur 3D-Kartierung von Bauwerksoberflächen wurden Untersuchungen zur Erfassung der Schäden an diesen Putzritzungen mit optischen 3D-Messverfahren und der aktiven Thermografie durchgeführt. Dabei wurden bei den optischen Verfahren hochauflösende Techniken zur Erfassung der Oberflächentopologie (Stereophotogrammmetrie) und zur Vermessung der Rissstrukturen und Ausbeulungen (3D-Trackingverfahren) eingesetzt. Die Zuordnung der Signaturen in den Thermogrammen zu Hohlstellen sowie Materialergänzungen und -ersatz wird diskutiert. Weiterhin erfolgt ein Vergleich der Ergebnisse mit Messungen an neu freigelegten Putzbereichen. T2 - Thermographie-Kolloquium 2013 CY - Leinfelden-Echterdingen, Germany DA - 26.09.2013 KW - Aktive Thermografie KW - Stereophotogrammetrie KW - Trackingsystem KW - Risse KW - Putz KW - Mauerwerk KW - Denkmalpflege PY - 2013 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-293987 SN - 978-3-940283-52-8 IS - DGZfP-BB 143 (Vortrag 6) SP - 1 EP - 8 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-29398 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maierhofer, Christiane A1 - Myrach, Philipp A1 - Steinfurth, Henrik T1 - Einfluss von Material, Messparametern und Umgebungsbedingungen auf die Nachweisempfindlichkeit der Blitzthermografie N2 - Dieser Beitrag fasst die Untersuchungsergebnisse zu den Verfahrensgrenzen der Blitzthermografie zur Ortung und Charakterisierung von Fehlstellen in Metallen zusammen. Regeln zur Abschätzung von Eindringtiefe und Tiefenauflösung werden vorgestellt und überprüft. Weiterhin werden Vorgehensweisen zur Optimierung des Intensitätskontrastes von Fehlstellenanzeigen vorgestellt. Einfache analytische Abschätzungen werden durch eine Vielzahl von experimentellen Untersuchungen an Kupfer- und Stahl-Probekörpern ergänzt. Dabei wurden sowohl die Parameter der Blitzlichtanregung als auch der Messwerterfassung umfassend variiert. T2 - DGZfP-Jahrestagung 2013 CY - Dresden, Germany DA - 06.05.2013 PY - 2013 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-285733 SN - 978-3-940283-49-8 IS - Di.2.A.1 SP - 1 EP - 8 PB - Deutsche Gesellschaft für zerstörungsfreie Prüfung e.V. (DGZfP) AN - OPUS4-28573 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kind, Thomas A1 - Kurz, J.H. A1 - Taffe, Alexander A1 - Wöstmann, Jens T1 - Ortung und Unterscheidung von Querspanngliedern hinter schlaffer Bewehrung mit dem Radarverfahren in einer Fahrbahnplatte N2 - Anhand eines erfolgreichen Messeinsatzes an einer Spannbetonbrücke, deren Querspannglieder zuverlässig lokalisiert und nachfolgend instandgesetzt werden sollen, wird die Vorgehensweise der Radarmessung mit zwei verschiedenen Polarisationsrichtungen der Antenne zur Unterscheidung von unterschiedlichen Arten der Bewehrungen ausführlich erklärt. Das Radarverfahren eignet sich sehr gut für die zerstörungsfreie Ortung von Bewehrung in Stahlbetonbauwerken. Insbesondere lässt sich mit dem Verfahren vorgespannte Bewehrung bis in einer Tiefe von ca. 30 cm und bei einem normalen Bewehrungsgrad (Maschenweite >10 cm) der schlaffen Bewehrung zuverlässig auffinden. Seit einigen Jahren wird das Radarverfahren erfolgreich im Vorfeld einer schadensfreien Kernbohrung im Rahmen von Ertüchtigungsmaßnahmen von Stahlbetonbrücken mit externen Spanngliedern angewendet. Aufgrund der Lage und dem Verlauf der vorgespannten Bewehrung in Hohlkastenseitenwänden und Plattenbalken kann eine vorgespannte Bewehrung von schlaffer Bewehrung in diesen Bauwerken sehr gut unterschieden werden. Diese Unterscheidungsmerkmale lassen sich aber bei Querspanngliedern in einer Fahrbahnplatte nur selten anwenden, da häufig die Überdeckung und der Abstand der schlaffen Bewehrung und der Querspannglieder ähnlich sind. In diesem Beitrag wird beschrieben, wie der gezielte Einsatz verschiedener Polarisationsrichtungen der Antenne zu einer zuverlässigen Unterscheidung von schlaffer Bewehrung und Spanngliedern beiträgt und damit zu einer verbesserten bildgebenden Darstellung der inneren Konstruktion der Fahrbahnplatte führt. T2 - DGZfP-Jahrestagung 2013 CY - Dresden, Germany DA - 06.05.2013 KW - Bauwesen KW - Zerstörungsfreie Prüfung PY - 2013 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-294454 SN - 978-3-940283-49-8 IS - DGZfP-BB 141 (Mi.1.B.3) SP - 1 EP - 9 PB - Deutsche Gesellschaft für zerstörungsfreie Prüfung e.V. (DGZfP) AN - OPUS4-29445 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wolf, Julia A1 - Mielentz, Frank A1 - Milmann, Boris A1 - Wiggenhauser, Herbert T1 - Grundlagenuntersuchungen von Ultraschall-Sensoren in Beton N2 - Für Ultraschallmessungen in Betonbauteilen wurden neuartige radialsymmetrisch abstrahlende Longitudinalwellenprüfköpfe mit einer Mittenfrequenz von 60 kHz auf deren Eignung hinsichtlich Abstrahlcharakteristik, Empfindlichkeit und Frequenzspektrum untersucht. Für die Messung der Abstrahlcharakteristiken wurden die Prüfköpfe vertikal und horizontal in Betonzylinder eingebettet und die Richtungsabhängigkeiten der Schallschnelle mithilfe eines Laservibrometers gemessen. Die Streuung der Prüfkopfempfindlichkeit wurde im Wasserbad unter Verwendung verschiedener Köpfe gleicher Bauart bestimmt. Außer Änderungen der Signalamplituden zeigten sich auch Schwankungen im Frequenzbereich bei verschiedenen Sender-Empfängerkombinationen. Die Schallschwächung des Betons hat Einfluss auf die erreichbare Auflösung der Messungen und damit auf die maximal möglichen Senderabstände im Bauteil. Durch experimentelle Untersuchungen und Simulationen erfolgte eine Optimierung der Abstände hinsichtlich des Aufwandes und der geforderten Auflösung. Die Signalschwächung im Beton wurde mit verschiedenen Impulsen im Frequenzbereich von 50 kHz bis 100 kHz in Abhängigkeit verschiedener Bewehrungsgrade und Korngrößen ermittelt. Hierfür wurden die Sensoren in unterschiedlichen Abständen in die Probekörper einbetoniert und die Empfangssignale hinsichtlich Amplitudenabfall und Frequenzspektrum untersucht. T2 - DGZfP-Jahrestagung 2013 CY - Dresden, Germany DA - 06.05.2013 PY - 2013 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-294153 SN - 978-3-940283-49-8 IS - DGZfP-BB 141 (Poster 56) SP - 1 EP - 9 PB - Deutsche Gesellschaft für zerstörungsfreie Prüfung e.V. (DGZfP) AN - OPUS4-29415 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kuhlich, Paul A1 - Emmerling, Franziska A1 - Kraus, Werner A1 - Nehls, Irene A1 - Piechotta, Christian T1 - 1-(4-bromo-3,5,5,6,8,8-hexamethyl-5,6,7,8-tetrahydronaphthalen-2-yl)ethan-1-one: a precursor for phase-I metabolite of AHTN N2 - The title compound, C18H25BrO, crystallized as a racemate with four independent molecules in the asymmetric unit. In the crystal, three of these four molecules are linked via C-Br...Br-C halogen bonds [Br...Br = 3.662 (2) and 3.652 (2) Å], forming dimers. PY - 2013 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-279935 DO - https://doi.org/10.1107/S1600536813006934 SN - 1600-5368 VL - 69 IS - 4 SP - o545, sup-1 EP - sup-17 PB - Munksgaard CY - Copenhagen AN - OPUS4-27993 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gebhardt, M.O. A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael T1 - Numerical analysis of hot cracking in laser-hybrid welded tubes N2 - In welding experiments conducted on heavy wall pipes, the penetration mode (full or partial penetration) occurred to be a significant factor influencing appearance of solidification cracks. To explain the observed phenomena and support further optimization of manufacturing processes, a computational model was developed, which used a sophisticated strategy to model the material. High stresses emerged in the models in regions which showed cracking during experiments. In partial penetration welding, they were caused by the prevention of weld shrinkage due to the cold and strong material below the joint. Another identified factor having an influence on high stress localization is bulging of the weld. PY - 2013 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-302961 DO - https://doi.org/10.1155/2013/520786 SN - 1687-8442 SN - 1687-8434 IS - Article ID 520786 SP - 1 EP - 8 PB - Hindawi Publishing Corporation CY - New York, NY, USA AN - OPUS4-30296 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schukar, Vivien A1 - Kusche, Nadine A1 - Kalinka, Gerhard A1 - Habel, Wolfgang T1 - Field deployable fiber bragg grating strain patch for long-term stable health monitoring applications N2 - A fiber Bragg grating (FBG) strain patch specially adapted for long-term and high-strain applications has been developed and characterized. The design concept for the patch is based on a glass-fiber reinforced plastic (gfrp) carrier material. The developed concept for the FBG integration into the carrier material was derived from reliable integration procedure of FBG sensors into composite structures. The patches' temperature sensitivity, strain gauge factor, fiber–matrix interface adhesion and fatigue behavior were characterized. As a result, FBG strain patches with linear temperature and strain behavior, as well as excellent fatigue resistance, were developed and can be used as part of a monitoring system for advanced composite materials in aerospace structures or wind turbine power plants. KW - Fiber Bragg grating KW - Patch KW - Strain gauge factor KW - Temperature sensitivity KW - Push-out test KW - Validation KW - Fatigue behavior PY - 2013 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-276271 DO - https://doi.org/10.3390/app3010039 SN - 2076-3417 VL - 3 IS - 1 SP - 39 EP - 54 PB - MDPI CY - Basel AN - OPUS4-27627 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wiggenhauser, Herbert A1 - Niederleithinger, Ernst T1 - Innovative ultrasonic techniques for inspection and monitoring of large concrete structures N2 - Ultrasonic echo and transmission techniques are used in civil engineering on a regular basis. New sensors and data processing techniques have lead to many new applications in the structural investigation as well as quality control. But concrete structures in the nuclear sector have special features and parameters, which pose problems for the methods and instrumentation currently available, e.g. extreme thickness, dense reinforcement, steel liners or special materials. Several innovative ultrasonic techniques have been developed to deal with these issues at least partly in lab experiments and pilot studies. Modern imaging techniques as multi-offset SAFT have been used e. g. to map delaminations. Thick concrete walls have successfully been inspected, partly through a steel liner. Embedded ultrasonic sensors have been designed which will be used in monitoring networks of large concrete structures above and below ground. In addition, sensitive mathematical methods as coda wave interferometry have been successfully evaluated to detect subtle changes in material properties. Examples of measurements and data evaluation are presented. KW - Automated scanning systems KW - Multi-Offset Array KW - Enhanced Imaging KW - Embedded ultrasonic sensors PY - 2013 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-290513 DO - https://doi.org/10.1051/epjconf/20135604004 SN - 2100-014X VL - 56 SP - 04004-1 EP - 04004-9 PB - EDP Sciences CY - Les Ulis AN - OPUS4-29051 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Krebber, Katerina ED - Harun, S.W. ED - Arof, H. T1 - Smart technical textiles based on fiber optic sensors N2 - Smart technical textiles are by definition textiles that can interact with their environment. They can sense and react to environmental conditions and external stimuli from mechanical, thermal, chemical or other sources. Such textiles are multifunctional or even “intelligent” which is fulfilled by a number of sensors incorporated in the textiles. The embedded sensors are sensitive to various parameters such as temperature, strain, chemical, biological and other substances. PY - 2013 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-289397 SN - 978-953-51-1148-1 DO - https://doi.org/10.5772/54244 IS - Section 3 / Chapter 12 SP - 319 EP - 344 PB - InTech AN - OPUS4-28939 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lopez-Heredia, M.A. A1 - Gildenhaar, Renate A1 - Berger, Georg A1 - Linow, Ulf A1 - Wirth, Cynthia A1 - Günster, Jens A1 - Houshmand, A. A1 - Stiller, M. A1 - Knabe-Ducheyne, C. T1 - Effect of stressed and unstressed cell culture environments on the viability of MC3T3 cells with calcium phosphates T2 - ISACB-6 - International symposium on apatite and correlative biomaterials CY - Nantes, France DA - 2013-06-05 KW - Cell culture media KW - Fetal bovine serum KW - Stressed KW - Unstressed KW - Calcium alkaline orthophosphates PY - 2013 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-299387 DO - https://doi.org/10.4172/2090-5025.S1-002 SN - 2090-5017 SN - 2090-5025 N1 - Geburtsname von Wirth, Cynthia: Gomes, C. M. - Birth name of Wirth, Cynthia: Gomes, C. M. SP - 1 EP - 3(?) PB - Ashdin AN - OPUS4-29938 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Woydt, Mathias A1 - Mohrbacher, H. T1 - The tribological and mechanical properties of niobium carbides (NbC) bonded with cobalt of Fe3Al N2 - The tribological and mechanical properties of niobium carbide bonded with 8 vol.-% (NbC-8Co), 12 vol.-% of cobalt (NbC-12Co) or 12 vol.-% of Fe3Al (NbC-12Fe3Al) are presented. Rotating discs made of metal-bonded niobium carbide were mated against alumina (99.7%) under unlubricated (dry) unidirectional sliding tests (0.1 m/s to 12.0 m/s; 22 °C and 400 C) as well as in oscillation tests (f=20 Hz, Δx=0.2 mm, 2/50/98% rel. humidity, n=105/106 cycles). Microstructure and phase compositions were determined as well. The tribological data obtained were benchmarked with different ceramics, cermets, hard metals and thermally sprayed coatings, where NbC bonded with 8% and 12% Co presented above 7 m/s the lowest wear rates so far in such a benchmark. Binderless NbC (HP-NbC1) and the metal-bonded NbCs exhibited low wear rates under dry sliding associated with P·V high load carrying capacities. NbC-based hard metal bonded with 12 vol.-% of Fe3Al resulted in a higher hardness level than for 12 vol.-% cobalt. The tribological profile established revealed a strong position of NbC-bearing materials under tribological considerations and for closed tribosystems against established reference tribo-couples. KW - Sliding KW - Ceramic KW - Oscillation KW - Strength KW - Modulus KW - High temperatures KW - Friction KW - Wear KW - NbC KW - Niobium carbide KW - Cobalt KW - Fe3Al KW - Hard metal PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-316129 DO - https://doi.org/10.1016/j.wear.2014.09.007 SN - 0043-1648 VL - 321 SP - 1 EP - 7 PB - Elsevier CY - Amsterdam AN - OPUS4-31612 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kunte, Hans-Jörg A1 - Lentzen, G. A1 - Galinski, E. T1 - Industrial production of the cell protectant ectoine: protection mechanisms, processes, and products N2 - Bacteria, Archaea and Eukarya can adapt to Saline environments by accumulating compatible solutes in order to maintain an osmotic equilibrium. Compatible solutes are of diverse chemical structure (sugars, polyols, amino acid derivatives) and are beneficial for bacterial cells not only as osmoregulatory solutes, but also as protectants of proteins by mitigating detrimental effects of freezing, drying and high temperatures. The aspartate derivative ectoine is a wide spread compatible solute in Bacteria and possesses additional protective properties compared with other compatible solutes, and stabilizes even whole cells against stresses such as UV radiation or cytotoxins. The protective properties of ectoine for proteins can be explained by its strong (kosmotropic) interaction with water and subsequent exclusion from Protein surface, the decrease of the solubility of the peptide backbone and the strengthening of intramolecular hydrogen bonds (secondary structures). The stabilizing and UV-protective properties of ectoine attracted industry, which saw the potential to market ectoine as a novel active component in health care products and cosmetics. In joint efforts of industry and research large-scale fermentation procedures have been developed with the halophilic bacterium Halomonas elongata used as a producer strain. The two key technologies that allow for the annual production of ectoine on a scale of tons are the bacterial milking procedure and the development and application of ectoine-excreting mutants (“leaky” mutant). The details of these two procedures including the strain development and Fermentation processes will be introduced and current and future applications of ectoine will be discussed. KW - Bacterial milking KW - Batch fermentation KW - Continuous culture KW - Ectoine excretion KW - Hofmeister effect KW - Kosmotrope KW - “leaky” mutant KW - Osmophobic effect KW - Protein protection KW - Preferential exclusion PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-376805 DO - https://doi.org/10.2174/22115501113026660037 SN - 2211-551X VL - 3 IS - 1 SP - 10 EP - 25 PB - Bentham Science AN - OPUS4-37680 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stoycheva, V. A1 - Goering, Harald A1 - Wolff, Dietmar A1 - Herzog, M. T1 - Bestimmung der Kohäsionsenergie- und Vernetzungsdichte von Polymeren mit Hilfe von Quellungsmessungen N2 - Bei der Abschätzung der Beständigkeit von Kunststoffen gegenüber niedermolekularen Flüssigkeiten ist die Kohäsionsenergiedichte CED ein wichtiger Parameter auf molekularer Ebene. Die Vernetzungsdichte ν eines polymeren Festkörpers bildet hierbei einen bedeutsamen Kennwert, der darüber hinaus neben der Löslichkeit wichtige Eigenschaften wie thermische Stabilität und Steifigkeit des Materials charakterisiert. Für die experimentelle Bestimmung von CED und ν eignet sich die Untersuchung des Quellverhaltens in unterschiedlichen Lösungsmitteln. Es werden zwei Messmethoden miteinander verglichen und die Ergebnisse unter Berücksichtigung des molekularen Aufbaus von Proben aus Polyurethan (PU) und hochmolekularem – (HMWPE) und ultrahochmolekularem Polyethylen (UHMWPE) diskutiert. Zum Verständnis des Quellverhaltens dieser Polymerproben in niedermolekularen Lösungsmitteln werden neben den Messergebnissen Literaturdaten zu Grunde gelegt. KW - Quellungsmessung KW - Kohäsionsenergie KW - Venetzungsdichte PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:526-opus4-3372 SN - 0949-8214 VL - 18 SP - 77 EP - 84 PB - News & Media CY - Berlin AN - OPUS4-32411 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schick, D. A1 - Herzog, M. A1 - Bojahr, A. A1 - Leitenberger, W. A1 - Hertwig, Andreas A1 - Shayduk, R. A1 - Bargheer, M. T1 - Ultrafast lattice response of photoexcited thin films studied by X-ray diffraction N2 - Using ultrafast X-ray diffraction, we study the coherent picosecond lattice dynamics of photoexcited thin films in the two limiting cases, where the photoinduced stress profile decays on a length scale larger and smaller than the film thickness. We solve a unifying analytical model of the strain propagation for acoustic impedance-matched opaque films on a semi-infinite transparent substrate, showing that the lattice dynamics essentially depend on two parameters: One for the spatial profile and one for the amplitude of the strain. We illustrate the results by comparison with high-quality ultrafast X-ray diffraction data of SrRuO3 films on SrTiO3 substrates. KW - Festkörperphysik KW - Dünnschichttechnik KW - Ellipsometrie KW - Röntgenbeugung KW - Optische Konstanten PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-322471 DO - https://doi.org/10.1063/1.4901228 SN - 2329-7778 VL - 1 IS - 6 SP - 064501-1 - 064501-13 PB - AIP Publishing LLC CY - Melville, NY AN - OPUS4-32247 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gaal, Mate A1 - Dohse, Elmar A1 - Bartusch, Jürgen A1 - Köppe, Enrico A1 - Kreutzbruck, Marc A1 - Hillger, W. A1 - Amos, J. M. T1 - Ultrasonic testing of adhesively bonded joints using air-coupled cellular polypropylene transducers N2 - In air-coupled ultrasonic testing, the impedance mismatch between the transducer and the air is commonly being solved by adding matching layers to composite transducers. To avoid the difficult technological procedure regarding matching layers, some new piezoelectric materials have been proposed. Most promising are ferroelectrets, which are charged cellular polymers, having ferroelectric and consequently piezoelectric properties. In particular, the extreme softness of cellular polypropylene (cPP) leads to a high piezoelectric constant and to a good impedance match with the air, making matching layers redundant. Its elasticity modulus below 1 MPa causes an additional effect not observed with common piezoelectric materials: that is the electrostrictive effect, here defined as the thickness change due to the attractive force between the transducer electrodes. This effect exceeds the piezoelectric effect at excitation voltages over 1 kV. The extreme softness of cPP leads also to high flexibility, enabling easy focusing by bending the transducer. We have developed air-coupled ultrasonic transducers based on cPP. This includes the electrical matching networks for the transmitter and for the receiver. The transmitter is excited with voltages up to 2.5 kV, so that the electrostrictive effect dominates, leading to sound pressure around 145dB at the transducer surface. These transducers have been applied for testing carbon-fiber-reinforced polymer plates, adhesive joints and other composite structures. Here we report about ultrasonic transmission of two types of adhesive joints. The first one is multi-layer aluminium components with some artificial disbonds, which are common in aerospace industry, and the second one is an aluminium-steel joint with polyurethane adhesive, which is used in automotive industry. T2 - ECNDT 2014 - 11th European conference on non-destructive testing CY - Prague, Czech Republic DA - 06.10.2014 KW - Air-coupled KW - Ultrasonic testing KW - Ferroelectret KW - Cellular polypropylene KW - Transducer KW - Adhesive joint PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-317204 SN - 978-80-214-5018-9 SP - 1 EP - 8 PB - Brno University of Technology AN - OPUS4-31720 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Köppe, Enrico A1 - Augustin, D. A1 - Bartholmai, Matthias A1 - Daum, Werner T1 - Air-based multi-hop sensor network for the localization of persons N2 - In this work an air-based sensor network for the localization of persons at extensive areas is presented. The developed network consists of a localization device which the person is wearing (BodyGuard-System), a mobile relay station in the air, and a base station. All three parts communicate with the same radio chip. The BodyGuard-System is an inertial navigation system which was developed for localization in difficult environments with high accuracy and low measurement uncertainty. To increase the range of the system, a multi-hop network was built up. The measured data of the BodyGuard-System and the mobile relay station is visualized on a PC in the base station. This multi-hop network is necessary for example for fire department missions. T2 - EuroSensors 2014, 28th European Conference on Solid-State Transducers CY - Brescia, Italy DA - 07.09.2014 KW - WSN KW - Mesh routing KW - Air-based KW - Multi-hop KW - Localization PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-324294 DO - https://doi.org/10.1016/j.proeng.2014.11.540 SN - 1877-7058 VL - 87 SP - 528 EP - 531 PB - Elsevier CY - Amsterdam [u.a.] AN - OPUS4-32429 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ewert, Uwe A1 - Zscherpel, Uwe T1 - Minimum requirements for digital radiography equipment and measurement procedures by different industries and standard organizations N2 - The digital photography has almost completely substituted the film photography. The film replacement is also fast progressing in medical X-ray radiography. This process is slower in NDT and especially in Europe. Reasons for the hesitating change to digital radiography (RT-D) in NDT are the necessary time for adoption of standards and the conservative request for film RT by auditors and NDT managers for applications in large plants and at construction areas. The fast serial inspection for small castings is already almost completely dominated by RT-D due to the cost effective short exposure and interpretation times. Standards were developed in parallel at CEN, ISO, ASTM and ASME. Unfortunately, the standard practices are different and the requirements on image quality and useable hardware are different too. The first standard series on Computed Radiography were developed and published by CEN and ASTM in 2005. Harmonized classification and qualification standards are available but the published practices are different. ASTM has developed the first standards for application of Digital Detector Arrays (DDA) in 2010. The first digital RT ISO standard practice is ISO 17636-2 (2013), which describes the practice for application of DDAs and Imaging Plates for weld inspection. At the first time this standard provides requirements for the selection of suitable hardware. Minimum image quality requirements are specified in analogy to film radiography and 3 Compensation Principles are defined to enable the application of a wider range of digital detectors. A comparison of the different international digital RT standards is given and first experiences with ISO 17636-2 are discussed. New standards on RT wall thickness and corrosion measurements (EN 16407, film and digital) have been developed recently. T2 - ECNDT 2014 - 11th European conference on non-destructive testing CY - Prague, Czech Republic DA - 06.10.2014 KW - NDT KW - X-Ray KW - Digital detectors KW - Standards KW - Radiographic procedures KW - Unsharpness KW - Basic spatial resolution KW - Requirements KW - Digital industrial radiology PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-323081 UR - https://www.ndt.net/?id=16708 SN - 1435-4934 VL - 19 IS - 12 SP - 1 EP - 18 PB - NDT.net CY - Kirchwald AN - OPUS4-32308 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Hothan, Sascha A1 - Häßler, Dustin T1 - Über die Entwicklung von Anwendungsregeln für reaktive Brandschutzsysteme auf Stahlzuggliedern N2 - Der vorliegende Beitrag stellt den Entwicklungsstand von Anwendungsregeln für reaktive Brandschutzsysteme auf Stahlzuggliedern zusammenfassend dar. Dabei wird insbesondere auf die jüngsten Veränderungen in den normativen Grundlagen und bauaufsichtlichen Regelungen eingegangen und im Hinblick auf Sicherheitsaspekte bewertet. Die Verringerung der Teilsicherheit für den Bauteilwiderstand nicht stabilitätsgefährdeter Bauteile im Regelwerk für die Kaltbemessung von Stahltragwerken ist hier als besonders kritisch anzusehen, da hierdurch ein systematisches Sicherheitsdefizit für den Brandfall verursacht wird. Weiterhin werden neuste Forschungsergebnisse bei der Entwicklung von Bewertungsregeln von reaktiven Brandschutzsystemen auf Vollkreisprofilen unter Zugbeanspruchung vorgestellt und diskutiert. Die Untersuchungen behandeln die Fragestellung, inwieweit Prüfungen mit Zugbeanspruchungen an Kreisvollprofilen erforderlich sein werden. KW - Stahlkonstruktion KW - Brandschutz KW - Reaktive Brandschutzsysteme KW - Zugglieder PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-307949 DO - https://doi.org/10.2314/GBV:77999762X SP - 141 EP - 148 PB - Institut für Stahlbau / Leibniz Universität Hannover CY - Hannover AN - OPUS4-30794 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Madia, Mauro A1 - Zerbst, Uwe A1 - Beier, H.T. T1 - A model for the determination of the fatigue life in technical alloys containing large and small defects N2 - The determination of the fatigue life in technical alloys containing large and small defects must rely on a propagation model which accounts for short and long crack growth. Recently an analytical model which incorporates propagation in the short crack regime and plastic correction for the crack driving force has been presented by two of the authors. This work is intended to show further validation of the model, taking into account data sets for different materials with different testing conditions. Despite the assumptions about missing parameters, the value of which had to be taken from the literature, the predictions showed a fairly good approximation of the fatigue lives. A possible interpretation of the results in terms of multiple crack initiation and propagation at higher loads is proposed. T2 - EFC20 - 20th European conference on fracture CY - Trondheim, Norway DA - 30.06.2014 KW - Fatigue strength KW - Crack propagation KW - Short cracks PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-311961 DO - https://doi.org/10.1016/j.mspro.2014.06.082 SN - 2211-8128 VL - 3 SP - 493 EP - 498 PB - Curran CY - Red Hook, NY, USA AN - OPUS4-31196 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mozetic, M. A1 - Ostrikov, K. A1 - Ruzic, D.N. A1 - Curreli, D. A1 - Cvelbar, U. A1 - Vesel, A. A1 - Primc, G. A1 - Leisch, M. A1 - Jousten, K. A1 - Malyshev, O.B. A1 - Hendricks, J.H. A1 - Kövér, L. A1 - Tagliaferro, A. A1 - Conde, O. A1 - Silvestre, A.J. A1 - Giapintzakis, J. A1 - Buljan, M. A1 - Radic, N. A1 - Drazic, G. A1 - Bernstorff, S. A1 - Biedermann, H. A1 - Kylián, O. A1 - Hanus, J. A1 - Milosevic, S. A1 - Galtayries, A. A1 - Dietrich, Paul A1 - Unger, Wolfgang A1 - Lehocky, M. A1 - Sedlarik, V. A1 - Stana-Kleinschek, K. A1 - Drmota-Petric, A. A1 - Pireaux, J.J. A1 - Rogers, J.W. A1 - Anderle, M. T1 - Recent advances in vacuum sciences and applications N2 - Recent advances in vacuum sciences and applications are reviewed. Novel optical interferometer cavity devices enable pressure measurements with ppm accuracy. The innovative dynamic vacuum standard allows for pressure measurements with temporal resolution of 2 ms. Vacuum issues in the construction of huge ultra-high vacuum devices worldwide are reviewed. Recent advances in surface science and thin films include new phenomena observed in electron transport near solid surfaces as well as novel results on the properties of carbon nanomaterials. Precise techniques for surface and thin-film characterization have been applied in the conservation technology of cultural heritage objects and recent advances in the characterization of biointerfaces are presented. The combination of various vacuum and atmospheric-pressure techniques enables an insight into the complex phenomena of protein and other biomolecule conformations on solid surfaces. Studying these phenomena at solid–liquid interfaces is regarded as the main issue in the development of alternative techniques for drug delivery, tissue engineering and thus the development of innovative techniques for curing cancer and cardiovascular diseases. A review on recent advances in plasma medicine is presented as well as novel hypotheses on cell apoptosis upon treatment with gaseous plasma. Finally, recent advances in plasma nanoscience are illustrated with several examples and a roadmap for future activities is presented. KW - Vacuum KW - Surface KW - Plasma KW - Interface KW - Nanoscience PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-304884 DO - https://doi.org/10.1088/0022-3727/47/15/153001 SN - 0022-3727 SN - 1361-6463 VL - 47 IS - 15 SP - 153001-1 EP - 153001-23 PB - IOP Publ. CY - Bristol AN - OPUS4-30488 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schott, M. A1 - Szczerba, Wojciech A1 - Kurth, D.G. T1 - Detailed study of layer-by-layer self-assembled and dip-coated electrochromic thin films based on metallo-supramolecular polymers N2 - Electrochromic thin films of metallo-supramolecular polyelectrolytes based on Fe(OAc)2 and 1,4-bis(2,2':6',2''-terpyridin-4'-yl)benzene are readily prepared by layer-by-layer (LbL) deposition or dip-coating on transparent conducting electrode surfaces. By applying a potential, we can switch the color of the films from blue to colorless. Because of the strong absorption and the fast switching speed, the color change can be observed with the eye. The devices show reversible switching and cycle stability. KW - Layer-by-layer self assembly KW - Dip coating KW - Thin films KW - Metallo-supramolecular polyelectrolytes KW - Electrochromism PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-317347 DO - https://doi.org/10.1021/la501590a SN - 0743-7463 SN - 1520-5827 VL - 30 IS - 35 SP - 10721 EP - 10727 PB - American Chemical Society CY - Washington, DC AN - OPUS4-31734 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cotic, P. A1 - Niederleithinger, Ernst A1 - Stoppel, Markus T1 - Unsupervised fusion of scattered data collected by a multi-sensor robot on concrete N2 - At BAM a multi-sensor robot system BetoScan is used for the investigation of reinforced concrete floors affected by corrosion in parking garages. Potential maps, as well as the distribution of concrete cover and moisture can be assessed simultaneously and data can be collected contactlessly. In order to evaluate the extent of degradation adequately and to divide the investigated structure into zones with defined damage classes, large data sets have to be collected and interpreted manually. Thus, to promote an efficient data evaluation framework, which could speed up and simplify the evaluation of large data sets, an unsupervised data fusion is of major interest. However, taking into account that collected data do not certainly coincide in space, a scattered data interpolation method should be applied prior data fusion. In the paper, a case study involving a BetoScan data set acquired from a reinforced concrete floor of a parking garage in Germany is presented. The data set includes potential mapping, covermeter based on eddy current, as well as microwave moisture measurements. Among the examined methods for interpolation of scattered data, kriging shows to yield smooth interpolated data plots even in the case of very sparse data. In the post-processing step, the investigated structure is efficiently segmented into zones using clustering based data fusion methods, which prove to be robust enough also for handling noisy data. Based on the minimization of the XB validity index, an unsupervised selection of optimal segmentation into damage classes is derived. T2 - DGZfP-Jahrestagung 2014 CY - Potsdam, Germany DA - 26.05.2014 KW - Robot KW - Data fusion KW - Ultrasonics KW - Radar KW - Potential method PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-337943 UR - http://www.ndt.net/article/dgzfp2014/papers/di2c1.pdf SN - 978-3-940283-61-0 IS - DGZfP-BB 148 SP - Di.2.C.1, 1 EP - 8 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-33794 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ritter, B. A1 - Krahl, T. A1 - Rurack, Knut A1 - Kemnitz, E. T1 - Nanoscale CaF2 doped with Eu3+ and Tb3+ through fluorolytic sol-gel synthesis N2 - In this article, the high potential of the fluorolytic sol–gel process to synthesize nanoscopic rare earth-doped calcium fluoride sols is shown. Through a fluorolytic sol–gel process we manage to achieve spherical monodisperse ~5 nm sized nanoparticles using a simple and reproducible one-pot-wet chemical route at room temperature. The as-synthesized clear sols exhibit an intense red and green luminescence under UV excitation at room temperature. A spectroscopic study of the sols revealed the characteristic transitions 5D0 → 7FJ of Eu3+ and 5D4 → 7FJ of Tb3+, with 5D0 → 7F2 (611 nm) of Eu3+ and 5D4 → 7F4 (581 nm) of Tb3+ as the most prominent transitions. This facile synthetic strategy is also valuable for developing other luminescent nanoparticles. KW - Calciumfluorid KW - Europium KW - Lumineszenz KW - Nanopartikel KW - Sol-Gel-Synthese KW - Terbium PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-320120 DO - https://doi.org/10.1039/c4tc01073f SN - 2050-7526 SN - 2050-7534 VL - 2 IS - 40 SP - 8607 EP - 8613 PB - Royal Soc. of Chemistry CY - Cambridge AN - OPUS4-32012 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schoknecht, Ute A1 - Kalbe, Ute A1 - Van Zomeren, A. A1 - Hjelmar, O. T1 - Laboratory leaching tests on treated wood according to different harmonised test procedures N2 - -Background- Laboratory leaching tests on treated wood were performed during a European robustness study in the framework of the validation of a tank leaching test procedure that has been proposed for construction products in order to determine the potential release of dangerous substances which can be transferred to soil and groundwater. The release of substances has to be determined also for materials treated with biocidal products according to the requirements of the European Biocidal Products Regulation. A similar leaching test procedure was already harmonised for treated wood for this purpose. Both test procedures were applied in parallel to wood treated with the same preservative to investigate whether the results of these tests can replace each other. Additional experiments were performed to further investigate unexpected effects of L/A ratio on leaching of copper and duration of storage of treated test specimens. -Results- Both procedures generate similar results concerning cumulative emissions of tebuconazole, copper, dissolved organic carbon and total nitrogen. The emission rates with time are in comparable ranges for both leaching protocols. Emissions of copper increased with decreasing L/A ratios. Strong correlation of copper concentrations and dissolved organic carbon as well as total nitrogen concentrations in eluates indicates that this observation is caused by co-elution of copper with organic substances. Duration of storage of treated test specimens affected emissions for the investigated wood preservative. -Conclusions- Based on these findings, results from both test procedures can be used to describe leaching characteristics and avoid double testing of treated wood to fulfil the requirements of the European regulations for either biocides or construction products. Leaching of substances from treated wood is a complex process that depends on its chemical composition and ageing processes. KW - Construction products KW - Biocidal product KW - Emission KW - Leaching KW - Tank leaching test KW - Treated wood KW - European regulation PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-317320 UR - http://www.enveurope.com/content/26/1/25 SN - 2190-4715 SN - 2190-4707 VL - 26 SP - 25, 1 EP - 10 PB - Springer CY - Berlin ; Heidelberg AN - OPUS4-31732 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Karabeliov, Krassimire A1 - Baeßler, Matthias A1 - Cuéllar, Pablo A1 - Rücker, Werner T1 - A method for system identification of a structure supported by nonlinear springs using evolutionary computing N2 - A mechanical structure supported by nonlinear springs subjected to an external load is considered. If all mechanical parameters of the system were known, the displacement of the system subjected to this load could be easily calculated. If not all of the parameters are known, but the load and the displacement are measured at one location, an inverse problem exists. In the presented problem the nonlinear springs are unknown and have to be determined. At first glance a problem needs to be solved, which is underdetermined due to the number of unknown variables. However, evolutionary computing can be applied to solve this inverse, nonlinear and multimodal problem. Sometimes a prior knowledge exists on certain system properties, which is difficult to implement into analytical or numerical solver. This knowledge can play a decisive role in identifying the system properties and it can be easily included as boundary condition when applying evolutionary algorithm. This article examines how and under what conditions the spring resistances can be identified. The procedure is exemplified at a mechanical system of a pile foundation. T2 - 2nd International conference on mathematical modeling in physical sciences 2013 CY - Prague, Czech Republic DA - 01.09.2013 PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-304531 UR - http://iopscience.iop.org/1742-6596/490/1/012095/pdf/1742-6596_490_1_012095.pdf DO - https://doi.org/10.1088/1742-6596/490/1/012095 SN - 1742-6588 SN - 1742-6596 VL - 490 IS - 012095 SP - 1 EP - 4 PB - IOP Publ. CY - Bristol, UK AN - OPUS4-30453 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Dittrich, Bettina A1 - Wartig, K.-A. A1 - Mülhaupt, R. A1 - Schartel, Bernhard T1 - Flame-retardancy properties of intumescent ammonium poly(phosphate) and mineral filler magnesium hydroxide in combination with graphene N2 - Thermally reduced graphite oxide (TRGO), containing only four single carbon layers on average, was combined with ammonium polyphosphate (APP) and magnesium hydroxide (MH), respectively, in polypropylene (PP). The nanoparticle's influence on different flame-retarding systems and possible synergisms in pyrolysis, reaction to small flame, fire behavior and mechanical properties were determined. TRGO has a positive effect on the yield stress, which is decreased by both flame-retardants and acts as a synergist with regard to Young's modulus. The applicability and effects of TRGO as an adjuvant in combination with conventional flame-retardants depends strongly on the particular flame-retardancy mechanism. In the intumescent system, even small concentrations of TRGO change the viscosity of the pyrolysing melt crucially. In case of oxygen index (OI) and UL 94 test, the addition of increasing amounts of TRGO to PP/APP had a negative impact on the oxygen index and the UL 94 classification. Nevertheless, systems with only low amounts (≤1 wt%) of TRGO achieved V-0 classification in the UL 94 test and high oxygen indices (>31 vol%). TRGO strengthens the residue structure of MH and therefore functions as a strong synergist in terms of OI and UL 94 classification (from HB to V-0). KW - Graphene KW - Intumescence KW - Ammonium polyphosphate KW - Magnesium hydroxide KW - Synergy KW - Polypropylene PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-320685 DO - https://doi.org/10.3390/polym6112875 SN - 2073-4360 VL - 6 IS - 11 SP - 2875 EP - 2895 PB - MDPI CY - Basel AN - OPUS4-32068 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zscherpel, Uwe A1 - Schumacher, David A1 - Redmer, Bernhard A1 - Ewert, Uwe A1 - Ullberg, C. A1 - Weber, N. A1 - Pantsar, T. T1 - Digital radiology with photon counting detectors N2 - The progress in X-ray detector electronics (sensitivity and speed) allows meanwhile fast single photon detection by a matrix detector. Combined photon counting and energy discrimination is implemented in the electronic circuit of each detector pixel. The company XCounter developed detectors based on CdTe single crystals, which can be tiled to larger areas and have a pixel size of 100ìm. The largest area available in beginning of 2014 is 50x75 mm². These detectors have very promising properties, which make them very suitable for NDT applications: 1. A CdTe attenuation layer of 750 µm thickness allows efficient X-ray detection up to ca. 300 keV. In counting mode only photon noise is important; no other detector noise sources need to be considered. There is no Offset signal without radiation. 2. Each of the detector pixels has two energy thresholds. These can be used for dual energy imaging for materials separation. Also the suppression of scattered radiation by energy thresholding will improve the image contrast sensitivity. First experiments will be presented which demonstrate the advantages of this new detector technology over the conventional charge integrating detectors. A challenge is the development of a modified detector calibration procedure, which becomes critical at longer exposure times. T2 - ECNDT 2014 - 11th European conference on non-destructive testing CY - Prague, Czech Republic DA - 06.10.2014 KW - Materials characterization KW - Radiographic testing (RT) KW - Digital detector array KW - Photo counting KW - Image quality KW - Calibration KW - Dual-energy KW - Energy discrimination KW - Digital radiology KW - Detectors PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-323063 UR - https://www.ndt.net/?id=16709 SN - 1435-4934 N1 - Geburtsname von Schumacher, David: Walter, D. - Birth name of Schumacher, David: Walter, D. VL - 19 IS - 12 SP - 1 EP - 8 PB - NDT.net CY - Kirchwald AN - OPUS4-32306 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schumm, A. A1 - Martin, E. A1 - Beaumont, M. A1 - Ewert, Uwe A1 - Kolkoori, Sanjeevareddy A1 - Zscherpel, Uwe A1 - Wrobel, Norma A1 - Redmer, Bernhard T1 - A comparative study on the performance of digital detector systems for high energy applications N2 - For cast components reaching or exceeding total material thicknesses of 150mm, high energy sources such as linear accelerators or Betatrons are required in order to obtain reasonable exposure times. In this study, the performance of digital detector systems, involving imaging plates (IP) and digital detector arrays (DDA), was evaluated with respect to the testing class B requirements as formulated in the standard EN ISO 17636-2. As a reference, traditional radiographic film and a Cobalt-60 source was used. With film exposures, testing class B was achieved with Co-60 and Betatron (7.5 MV) at longer exposure times. The preliminary results show that the testing class B was not obtained with the examined digital detector arrays (DDA) and the high resolution imaging plates (IP) , even at 40, 60 and 80 minutes exposure time with a 7.5 MV Betatron. Class A was achieved using high resolution imaging plates with optimized metal filters between object and IPs and a high resolution DDA with intermediate Cu filters. Class A was also achieved applying a DDA with lower basic spatial resolution than required by Table B.13 of EN ISO 17636-2, but using the compensation principle as described in this standard. The next generation of digital detector arrays might potentially be able to obtain class B performance with the expected spatial resolution and sensitivity improvements. T2 - ECNDT 2014 - 11th European conference on non-destructive testing CY - Prague, Czech Republic DA - 06.10.2014 KW - Radiography KW - Image quality KW - Betatron KW - Digital detector array (DDA) KW - Casting KW - Standards KW - High energy radiography KW - Comparison of detectors KW - Steel weldment PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-323075 UR - https://www.ndt.net/?id=16394 SN - 1435-4934 VL - 19 IS - 12 SP - 1 EP - 6 PB - NDT.net CY - Kirchwald AN - OPUS4-32307 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Fischer, Franziska A1 - Scholz, G. A1 - Benemann, Sigrid A1 - Rademann, K. A1 - Emmerling, Franziska T1 - Evaluation of the formation pathways of cocrystal polymorphs in liquid-assisted syntheses N2 - The synthesis of the polymorphic cocrystal caffeine:anthranilic acid was investigated to obtain a better understanding of the processes leading to the formation of different polymorphic forms. In the case of these cocrystal polymorphs synthesized by liquid-assisted grinding a distinct influence of the dipole moment of the solvent was found. A pre-coordination between the solvent molecules and the caffeine:anthranilic acid cocrystal could be identified in the formation of form II. In the case of form II the solvent can be regarded as a catalyst. The formation pathway of each polymorph was evaluated using synchrotron X-ray diffraction. KW - cocrystal KW - synchrotron X-ray diffraction KW - caffeine PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-313222 DO - https://doi.org/10.1039/c4ce00472h SN - 1466-8033 VL - 16 IS - 35 SP - 8272 EP - 8278 CY - London, UK AN - OPUS4-31322 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Andrae, K. A1 - Merkel, Stefan A1 - Durmaz, V. A1 - Fackeldey, K. A1 - Köppen, Robert A1 - Weber, M. A1 - Koch, Matthias T1 - Investigation of the ergopeptide epimerization process N2 - Ergopeptides, like ergocornine and a-ergocryptine, exist in an S- and in an R-configuration. Kinetic experiments imply that certain configurations are preferred depending on the solvent. The experimental methods are explained in this article. Furthermore, computational methods are used to understand this configurational preference. Standard quantum chemical methods can predict the favored configurations by using minimum energy calculations on the potential energy landscape. However, the explicit role of the solvent is not revealed by this type of methods. In order to better understand its influence, classical mechanical molecular simulations are applied. It appears from our research that 'folding' the ergopeptide molecules into an intermediate state (between the S- and the R-configuration) is mechanically hindered for the preferred configurations. KW - Ergopeptide KW - Epimerization KW - Hybrid monte carlo KW - Molecular dynamics KW - Conformation KW - Quantum mechanics PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-324632 DO - https://doi.org/10.3390/computation2030102 SN - 2079-3197 VL - 2 IS - 3 SP - 102 EP - 111 PB - MDPI CY - Basel AN - OPUS4-32463 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Myrach, Philipp A1 - Maierhofer, Christiane A1 - Reischel, Mercedes A1 - Rahammer, M. A1 - Holtmann, N. T1 - Untersuchung der Auflösungsgrenzen der Lockin-Thermografie zur Prüfung von Faserverbundwerkstoffen N2 - Aktive Thermografie mit Lockin-Anregung stellt ein berührungsfreies und zerstörungsfreies Prüfverfahren dar, welches insbesondere auch die Prüfung von kohlenstofffaserverstärkten Kunststoffen ermöglicht. Um eine Standardisierung dieses Verfahrens voranzubringen, wurden im Rahmen eines Forschungsprojektes umfangreiche Untersuchungen zur Validierung des Verfahrens durchgeführt. Dabei wurden unter anderem der Einfluss der spektralen Empfindlichkeit verschiedener Kamerasysteme, unterschiedlicher Lagenaufbauten bei CFK-Probekörpern und der Einfluss einer Phasenverschiebung zwischen dem Anregungssignal und der Detektion der Thermografiebilder untersucht. T2 - DGZfP-Jahrestagung 2014 CY - Potsdam, Germany DA - 26.05.2014 KW - Aktive Thermografie KW - Lockin-Thermografie KW - CFK PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-309259 SN - 978-3-940283-61-0 IS - DGZfP-BB 148 SP - Di.3.C.3, 1 EP - 10 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-30925 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kreutzbruck, Marc A1 - Bauer, P. A1 - Caspers, F. A1 - Heck, S. A1 - Müller, F. A1 - Pohl, Rainer A1 - Scheuerlein, C. A1 - Sickert, Roland A1 - Maierhofer, Christiane A1 - Brackrock, Daniel T1 - Sensoren für Verbunddrähte aus Niob-Titan und Kupfer N2 - Der Large Hadron Collider (LHC) des europäischen Kernforschungszentrums CERN ist einer der weltweit größten und leistungsfähigsten Teilchenbeschleuniger. Um den Teilchenstrahl auf seiner Kreisbahn zu halten, werden mit Hilfe supraleitender Spulen sehr starke Magnetfelder erzeugt. Die hierzu benötigten hohen Ströme werden über Verbunddrähte aus Niob-Titan und Kupfer geleitet. Die Drähte werden u.a. durch Ultraschallschweißungen miteinander verbunden. Eine mangelhafte Verbindung kann zur Erwärmung der Kontaktstelle und in Folge davon zum Zusammenbruch der Supraleitung führen. Auf Anfrage des CERN wurden an der BAM Untersuchungen zur Prüfbarkeit solcher Verbindungen bei Umgebungstemperatur durchgeführt. Es gelang, für einen Verbindungstypen einen Wirbelstromsensor für eine manuelle Prüfung zu entwickeln. Ein Prototyp des Sensors befindet sich beim CERN in der praktischen Erprobung. Das Sensorprinzip sowie Prüfergebnisse aus Labor und Praxis werden vorgestellt. T2 - DGZfP-Jahrestagung 2014 CY - Potsdam, Germany DA - 26.05.2014 KW - Ultraschallprüfung mit Matrix-Sensoren KW - Aktive Thermografie KW - Gabelsensor PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-319785 SN - 978-3-940283-61-0 VL - 148 SP - 1 EP - 12 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) CY - Berlin AN - OPUS4-31978 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gravenkamp, Hauke A1 - Song, C. T1 - Innovative numerische Methoden zur Simulation geführter Ultraschallwellen N2 - Geführte Ultraschallwellen bieten eine Vielzahl von Einsatzmöglichkeiten in der Zerstörungsfreien Prüfung, der Zustandsüberwachung sowie der Materialcharakterisierung. Insbesondere für Rohrleitungen und ausgedehnte Plattenstrukturen ist eine Vielzahl von auf geführten Wellen basierenden Verfahren in der Entwicklung und teilweise bereits im Einsatz. Aufgrund des komplexen Ausbreitungsverhaltens geführter Wellen werden numerische Verfahren (etwa die Finite Elemente Methode (FEM) oder die Randelementemethode (BEM)) zur Simulation der Wellenausbreitung sowie der Wechselwirkung mit Defekten in Wellenleitern angewendet. Diese Methoden sind für große Strukturen extrem rechenintensiv und umständlich in der Anwendung. Ein ungleich effizienteres Verfahren wurde kürzlich von den Autoren auf Grundlage der Scaled Boundary Finite Element Method entwickelt. Ein semi-analytischer Ansatz erlaubt die Modellierung beliebig ausgedehnter Strukturen bei extrem kurzen Rechenzeiten. Die Wechselwirkung geführter Wellen mit Rissen kann auf besonders elegante und exakte Weise beschrieben werden. Mit dieser Methode können die komplexen Vorgänge in Wellenleitern innerhalb weniger Sekunden modelliert werden. T2 - DGZfP-Jahrestagung 2014 CY - Potsdam, Germany DA - 26.04.2014 PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-313610 SN - 978-3-940283-61-0 IS - DGZfP-BB 148 SP - Poster 66, 1 EP - 6 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-31361 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Brackrock, Daniel A1 - Recknagel, Christoph A1 - Brekow, Gerhard A1 - Kreutzbruck, Marc T1 - Untersuchungen von Glas-Metall Klebverbindungen mit Hilfe von Ultraschall N2 - Klebverbindungen im modernen Hochbau können helfen, innovative ästhetische Bedürfnisse im Fassadenbau umzusetzen, technologische Verbesserungen zu erreichen, aber auch die Wechselwirkung von Gebäuden mit der Umwelt unter energetischen Aspekten zu optimieren. Aufgrund der hohen sicherheitstechnischen Bedeutung gibt es hohe Anforderungen an die Leistungsfähigkeit, Dauerhaftigkeit und die Gütesicherheit. Mit einer zerstörungsfreien praxistauglichen Prüftechnik, die eine sichere Überprüfung der Integrität von Glas-Metall Klebverbindungen im Ingenieurhochbau gewährleistet, kann sowohl ein wichtiger Beitrag zur Qualitätssicherung bei der Herstellung von Fassadenelementen aber auch bei der späteren Bauwerksüberwachung im Verlauf der Nutzungsdauer geleistet werden. Für eine Beurteilung der Qualität der Verbundfuge (z.B. bezgl. Standsicherheit) sind dabei Aussagen zur Homogenität der Verbundfuge, zum adhäsiven und kohäsiven Verbundverhalten gefordert. Hierzu besteht aktuell insbesondere Bedarf an zerstörungsfreien praxisgerechten, hoch ortsauflösenden und möglichst bildgebenden Untersuchungsverfahren. Es wird mit einem Matrixarray und mit konventionellen Winkelprüfköpfen eine Prüftechnik vorgestellt, mit der die Wechselwirkung zwischen Ultraschallwelle und Fehlstelle in der Klebefuge untersucht wird. Hierbei ist das erste Untersuchungsziel, mit einer angepassten Ultraschall-Prüftechnik mögliche Inhomogenitäten oder Schädigungsstellen in der geklebten Glas-Metall Verbindung zu detektieren. Über diese qualitativen Aussagen hinaus werden weiterführende Informationen über die flächenhafte Ausdehnung und den Ort einer mangelnden Klebung ermittelt. Dazu werden die Messwerte zusammen mit den Positionen des Ultraschallprüfkopfs aufgezeichnet. Mit Hilfe einer bildhaften Auswertung der gemessenen Ultraschallechos in Abhängigkeit vom Prüfkopfort werden die Möglichkeiten einer detaillierten Integritätsanalyse der Glas-Metall Klebschicht dargestellt. In diesem Beitrag werden experimentelle Prüfergebnisse vorgestellt, die im Sinne einer Verfahrensvalidierung an einem speziellen Beispielprobekörper zur Nachstellung einer SSG-Verglasung (ermittelt wurden und die Detektion fehlerhafter Klebestellen in einer Glas-Metall-Klebverbindung zum Ziel haben. T2 - DGZfP-Jahrestagung 2014 CY - Potsdam, Germany DA - 26.05.2014 PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-331181 UR - https://www.ndt.net/?id=17428 SN - 978-3-940283-61-0 VL - 148 SP - 1 EP - 8 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) CY - Berlin AN - OPUS4-33118 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Heinrich, Thomas A1 - Traulsen, Christoph Hans-Henning A1 - Darlatt, Erik A1 - Richter, S. A1 - Poppenberg, J. A1 - Traulsen, N.L. A1 - Linder, I. A1 - Lippitz, Andreas A1 - Dietrich, Paul A1 - Dib, B. A1 - Unger, Wolfgang A1 - Schalley, C.A. T1 - The versatility of 'Click' reactions at surfaces: Molecular recognition at interfaces N2 - In order to investigate molecular recognition on surfaces, an azide-functionalized monolayer was deposited on gold. The monolayer was characterized by X-ray photoelectron spectroscopy (XPS) and angle-resolved near-edge X-ray absorption fine structure (NEXAFS) experiments and the decomposition of the azide upon irradiation with X-ray beams was investigated. Subsequently, various alkyne-functionalized host and guest molecules were attached to the azide by 1,3-dipolar cycloaddition. These modified surfaces and their host–guest chemistry were analysed by XPS and angle-resolved NEXAFS. The reversibility of guest binding was shown for one example as a proof of principle. KW - 'Click' reaction KW - Azide-terminated surfaces KW - SAMs KW - Host guest molecules KW - Molecular recognition at interfaces PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-306463 DO - https://doi.org/10.1039/C4RA01730G SN - 2046-2069 VL - 4 IS - 34 SP - 17694 EP - 17702 PB - RSC Publishing CY - London AN - OPUS4-30646 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Feldmann, Rüdiger A1 - Zoёga, Andreas A1 - Milmann, Boris A1 - Krause, Martin T1 - Ortung tiefliegender Bewehrung durch Ultraschall mit bildgebender Phasenauswertung N2 - Die Ortung von schlaffer Bewehrung in Beton erfolgt routinemäßig mit bildgebenden Radar- oder Wirbelstromverfahren. Die Anwendung dieser Verfahren ist aber begrenzt, wenn es sich um die Ortung tiefliegender Bewehrung (ab ca. 30 cm) oder um jungen Beton handelt. Grund ist die Schwächung der Radarpulse durch oberflächennahe Bewehrung oder durch die Betonfeuchte. Das bildgebende Ultraschallechoverfahren bietet den Vorteil, dass die Ultraschallpulse in diesen Fällen eine wesentlich höhere Eindringtiefe erreichen. Im vorliegenden Beitrag wird eine Fallstudie vorgestellt, bei der mehrlagig eingebrachte Bewehrungseisen in einer nur einseitig zugänglichen 60 cm dicken Betonplatte geortet werden sollten, um eine Kernbohrung ohne Verkanten der Bohrkrone durchzuführen. Zur Ortung der Bewehrung wurde das Ultraschallechoverfahren mitScherwellen der Mittenfrequenz 50 kHz mit einem automatisch arbeitenden Bauwerksscanner eingesetzt. Aus den flächig aufgenommenen Messdaten wurde mit der Rekonstruktionsrechnung nach dem Prinzip der synthetischen Apertur (SAFT, Synthetic Aperture Focusing Technique) die Position der Bewehrungseisen bildhaft ortsgenau dargestellt. Dies gelingt mit einer Auswertungsoption, bei der die Phase der reflektierten Ultraschallpulse ermittelt und farbcodiert dargestellt wird (Phasenauswertung). Damit lassen sich Reflexionen der Bewehrung eindeutig von eventuellen Fehlstellen oder Rückwandechos unterscheiden. T2 - Fachtagung Bauwerksdiagnose 2014 CY - Berlin, Germany DA - 13.02.2014 KW - Ultraschallecho-Verfahren KW - SAFT KW - Bewehrung KW - Beton KW - Abbildungsverfahren PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-351056 UR - https://www.ndt.net/?id=15885 SN - 1435-4934 VL - 19 IS - 8 SP - 1 EP - 11 PB - NDT.net CY - Kirchwald AN - OPUS4-35105 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lange, Axel A1 - Kupsch, Andreas A1 - Hentschel, Manfred P. A1 - Lück, S. A1 - Schmidt, V. A1 - Grothausmann, R. A1 - Hilger, A. A1 - Manke, I. T1 - Reduzierung von Missing-Wedge-Artefakten mit DIRECTT N2 - Wir stellen eine Prozedur vor, mit der typische 'Missing Wedge' (MW)-Artefakte in CT-Rekonstruktionen effektiv unterdrückt werden können. Dazu wird der iterative DIRECTT-Algorithmus (Direkte Iterative Rekonstruktion Computertomographischer Trajektorien) mit einigen Zyklen diskreter Rekonstruktion eingesetzt. Die Kernfunktionen des Algorithmus', die wiederholte Auswahl und Gewichtung von Elementen einer Zwischenkonstruktion, werden beibehalten. Abgesehen von Sonderfällen der Röntgen- und Neutronentomographie tritt die MW-Restriktion (neben einer Vielzahl anderer) in Standardkonfigurationen der Elektronentomographie auf. Um den MW-Effekt isoliert zu untersuchen und beurteilen zu können, werden hier vollständige experimentelle Datensätze einer bekannten Porenstruktur um einen Sektor beschnitten sowie MW-Rekonstruktionen von Porenmodellen erzeugt. Die Ergebnisse werden mit zurzeit verbreiteten Algorithmen (Gefilterte Rückprojektion (FBP) und ART-Varianten) verglichen. Die Bewertung im Fourierraum zeigt, dass DIRECTT die fehlende Information im MW erfolgreich ergänzt. Zur quantitativen Bewertung der lokalen Rekonstruktionsqualität werden Methoden der räumlichen Statistik eingesetzt. T2 - DGZfP-Jahrestagung 2014 CY - Potsdam, Germany DA - 26.05.2014 KW - Computertomographie (CT) KW - Rekonstruktionsalgorithmus KW - DIRECTT KW - Missing Wedge KW - Statistische Bewertung PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-312977 SN - 978-3-940283-61-0 IS - DGZfP-BB 148 SP - Poster 18, 1 EP - 8 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) AN - OPUS4-31297 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Vöse, Markus A1 - Fedelich, Bernard A1 - Otto, F. A1 - Eggeler, G. T1 - Micromechanical modeling of creep damage in a copper-antimony alloy N2 - A micromechanical model of creep induced grain boundary damage is proposed, which allows for the simulation of creep damage in a polycrystal with the finite element method. Grain boundary cavitation and sliding are considered via a micromechanically motivated cohesive zone model, while the grains creep following the slip system theory. The model has been calibrated with creep test data from pure Cu single crystals and a coarse-grained polycrystalline Cu-Sb alloy. The test data includes porosity measurements and estimates of grain boundary sliding. Finally, the model has been applied to Voronoi models of polycrystalline structures. In particular the influence of grain boundary sliding on the overall creep rate is demonstrated. T2 - ECF20 - 20th European conference on fracture CY - Trondheim, Norway DA - 28.06.2014 KW - Creep damage KW - Grain boundary sliding KW - Cohesive zone KW - Micromechanical model KW - Polycrystal PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-309914 DO - https://doi.org/10.1016/j.mspro.2014.06.006 SN - 2211-8128 VL - 3 SP - 21 EP - 26 PB - Curran CY - Red Hook, NY, USA AN - OPUS4-30991 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Epishin, A.I. A1 - Link, T. A1 - Fedelich, Bernard A1 - Svetlov, I.L. A1 - Golubovskiy, E.R. T1 - Hot isostatic pressing of single-crystal nickel-base superalloys: mechanism of pore closure and effect on mechanical properties N2 - Pore annihilation was investigated in the single-crystal nickel-base superalloy CMSX-4. HIP tests at 1288 °C/103 MPa were interrupted at different times, then the specimens were investigated by TEM, metallography and density measurements. The kinetics of pore annihilation was determined. The pore closure mechanism was identified as plastic deformation on the octahedral slip systems. A model describing the kinetics of pore closure has been developed on the base of crystal plasticity and large strain theory. Mechanical tests with the superalloy CMSX-4 and the Ru-containing superalloy VGM4 showed, that HIP significantly increases the fatigue life at low temperatures but has no effect on creep strength. T2 - Eurosuperalloys 2014 - 2nd European symposium on superalloys and their applications CY - Giens, France DA - 12.05.2014 PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-316410 DO - https://doi.org/10.1051/matecconf/20141408003 N1 - Serientitel: MATEC Web of conferences – Series title: MATEC Web of conferences VL - 14 SP - 08003-1 EP - 08003-6 PB - EDP Sciences AN - OPUS4-31641 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Batzdorf, Lisa A1 - Wilke, Manuel A1 - Szczerba, Wojciech A1 - Reinholz, Uwe A1 - Emmerling, Franziska T1 - Mechanochemical synthesis and characterisation of two new bismuth metal organic frameworks N2 - Two metal organic structures composed of the ligands benzene-1,4-dicarboxylate and pyridine-2,5-dicarboxylate and bismuth cations are presented: (H2Im)[Bi(1,4-bdc)2] (1) and [Bi(pydc)(NO3)2(H2O)2]*H2O (2) (bdc = benzenedicarboxylate, H2Im = imidazole cation, pydc = pyridinedicarboxylate). Both compounds were synthesised via grinding and the crystal structure of compound (2) was solved based on its powder diffraction pattern. Compound 1 crystallises isostructurally to the dimethyl ammonium containing compound (dma)[(Bi(1,4-bdc)2]. Raman spectroscopy and Extended X-ray absorption fine structure (EXAFS) measurements provided additional information about the two mechanochemically synthesised metal organic compounds. KW - Crystal structure KW - Mechanochemically synthesis KW - Powder diffraction measurements PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-306296 DO - https://doi.org/10.1039/C3CE42633E SN - 1466-8033 N1 - Geburtsname von Batzdorf, Lisa: Tröbs, L. - Birth name of Batzdorf, Lisa: Tröbs, L. VL - 16 IS - 25 SP - 5560 EP - 5565 CY - London, UK AN - OPUS4-30629 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Batzdorf, Lisa A1 - Emmerling, Franziska T1 - Mechanochemical synthesis and characterisation of cocrystals and metal-organic compounds N2 - The mechanochemical synthesis of two model compounds, a metal organic framework ([Bi(1,4-bdc)2]*(Im) (bdc = benzene dicarboxylate, Im = imidazole cation)) and a cocrystal (Carbamazepine:Indometacin 1:1) were followed ex situ by combined analytical methods. Powder X-ray diffraction (XRD) and Raman spectroscopy data were evaluated for the synthesis of the metal organic framework. XRD measurements and REM images were analysed for the synthesis of the cocrystal. The measurements revealed that both model compounds were synthesised within minutes. The metal organic framework [Bi(1,4-bdc)2]*(Im) is synthesised via an intermediate structure. The cocrystal Carbamazepine:Indometacin 1:1 is formed within few seconds and afterwards the crystallite size decreases extremely. KW - Powder X-ray diffraction (XRD) KW - Raman spectroscopy KW - mechanochemical synthesis PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-306305 UR - http://pubs.rsc.org/en/content/articlepdf/2014/fd/c3fd00163f DO - https://doi.org/10.1039/C3FD00163F SN - 1359-6640 SN - 1364-5498 N1 - Geburtsname von Batzdorf, Lisa: Tröbs, L. - Birth name of Batzdorf, Lisa: Tröbs, L. SP - 109 EP - 119 PB - RSC CY - Cambridge [u.a.] AN - OPUS4-30630 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Nariaki, D. A1 - Lekovic, F. A1 - Homenya, P. A1 - Costa, B. F. O. A1 - Menzel, Michael A1 - Boca, R. A1 - Blumers, M. A1 - Klingelhöfer, G. A1 - Renz, F. T1 - Iron(III) complexes on a dendrimeric basis and various amine core investigated by Mössbauer spectroscopy N2 - Dendrimers of various generations were synthesized by the divergent method. Starting from various amine cores (G0a, G0b, G0c) the generations were built by reaction of the amine with acrylnitrile followed by hydrogenation with DIBAL-H. Treatment with salicylaldehyde creates a fivefold coordination sphere for iron in the molecular periphery. The resulting multinuclear coordination compounds are investigated by Mossbauer spectroscopy. T2 - ICRTP 2014 - International conference on recent trends in physics CY - Indore, India DA - 22.02.2014 PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-316331 DO - https://doi.org/10.1088/1742-6596/534/1/012003 SN - 1742-6588 SN - 1742-6596 VL - 534 IS - 1 SP - 012003-1 EP - 012003-8 PB - IOP Publ. CY - Bristol, UK AN - OPUS4-31633 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kruschwitz, Sabine T1 - Feuchtemessung im Bauwesen - Ein Überblick N2 - Ein Großteil der Schäden im Baubereich ist auf feuchteinduzierte Prozesse zurückzuführen. Der Erhaltungsaufwand allein im Hochbau wurde bereits vor einiger Zeit auf jährlich ca. 35 Mrd. Euro geschätzt. Aus diesem Grund hat die Feuchtemessung in der Bauwerksdiagnose eine sehr hohe Bedeutung - und im Idealfall sollte sie natürlich alles können: schnell sein, wiederholbar und zerstörungsfrei anwendbar. Zwar gibt es eine Vielzahl an verfügbaren Feuchtemesstechniken, oft fällt es Anwendern aber schwer, einzuschätzen welches die richtige Prüfmethode für ihr Problem ist. Genormt sind nur direkte und zerstörende Verfahren, die zwar teils hochgenau, aber doch nur stichprobenartig Aussagen liefern können. Die anderen, zerstörungsfreien Methoden basieren auf der Änderung feuchteabhängiger physikalischer Materialeigenschaften. Ihre Grundlagen, sowie Vor- und Nachteile werden hier näher dargestellt. T2 - Fachtagung Bauwerksdiagnose 2014 CY - Berlin, Germany DA - 13.02.2014 KW - Feuchtemessung KW - Zerstörungsfreie Prüfung KW - Baustoffe PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-311672 UR - http://www.bauwerksdiagnose2014.de/portals/bwd2014/BB/vortrag%205.pdf UR - http://www.bauwerksdiagnose2014.de/Berichtsband SN - 978-3-940283-56-6 SP - 1 EP - 8 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) CY - Berlin AN - OPUS4-31167 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lexow, Jürgen T1 - Industrial safety - Public demand and an answer of BAM the federal German institute for materials research and testing N2 - Safe industrial operation is expected by the public. It contributes to a clean environment, innovation and prosperity. BAM the Federal German Institute for Materials Research and Testing has its responsibility in further developing safety in technology and chemistry by research, testing and expert advice. The basic reasoning for this activity and examples of current work are provided. Particular attention is given to the unique BAM Test site Technical Safety. Acceptance of fi ndings and transfer of results are based on collaboration and exchange of personal. Modes of cooperation are described. KW - Industrial safety KW - Large test fecility KW - Structural integrity KW - Dangerous substance PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-322519 DO - https://doi.org/10.2478/tvsbses-2014-0010 SN - 1805-3238 VL - 9 IS - 2 SP - 40 EP - 45 PB - VSB - Sborník vedeckých prací Vysoké Skoly Bánské - Technické Univerzity Ostrava CY - Ostrava AN - OPUS4-32251 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kolkoori, Sanjeevareddy A1 - Wrobel, Norma A1 - Deresch, Andreas A1 - Redmer, Bernhard A1 - Ewert, Uwe T1 - Dual high-energy X-ray digital radiography for material discrimination in cargo containers N2 - In this contribution, we present a dual high-energy X-ray imaging technique for cargo container inspection using the 'spectral high-energy X-ray attenuation method'. This method is based on attenuation of continuous highenergy spectra. The developed experimental technique consists of a betatron as high-energy (up to 7.5 MeV) X-ray source and a matrix detector with high spatial resolution (400 ìm) for digital X-ray imaging. In order to evaluate the material discrimination capability using dual high-energy X-ray imaging, a test specimen is proposed, comprising step wedges of different low and high atomic number (Z) materials. The selected X-ray spectra for the dual-energy experiments correspond to 3 MV and 7.5 MV acceleration potential of the betatron. We evaluated the ratio between low- and high-energy X-ray attenuation coefficients quantitatively based on simulated poly-energetic high-energy X-ray source spectra and the detector sensitivity using the 'analytical Radiographic Testing inspection simulation tool' (aRTist) developed at BAM. The simulated effective attenuation coefficients are compared with corresponding experimental results in order to establish a method for identification of low- and high-Z materials in the container. Finally, important applications of the proposed technique in the context of aviation security are discussed. T2 - ECNDT 2014 - 11th European conference on non-destructive testing CY - Prague, Czech Republic DA - 06.10.2014 KW - Digital radiography KW - NDT KW - High-energy X-ray imaging KW - Betatron KW - Digital detector array (DDA) KW - Container inspection KW - Material discrimination KW - Effective attenuation coefficient PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-322394 UR - https://www.ndt.net/?id=16430 SN - 1435-4934 VL - 19 IS - 12 SP - 1 EP - 10 PB - NDT.net CY - Kirchwald AN - OPUS4-32239 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wrobel, Norma A1 - Kolkoori, Sanjeevareddy A1 - Zscherpel, Uwe A1 - Ewert, Uwe T1 - Innovative X-ray backscatter technique for security applications: Detection of dangerous materials N2 - Radiological inspections, in general, are NDT&E methods to detect the bulk of explosives without invasion into the object of analysis. In contrast to personal luggage, cargo or structural components constitute a complexity that may significantly hamper the detection of a threat by conventional transmission radiography. A novel approach of interrogating a large object to a certain depth only with a single sided access will be presented. It consists of an X-ray backscatter camera with a special twisted slit collimator for imaging backscattered objects. The new X-ray backscatter camera is not only imaging the objects due to their densities but also by taking into account the influences of surrounding objects. Additionally, it does not only image illuminated features but also depicts shadows from absorbing materials. This is a unique characteristic of the developed X-ray backscatter camera. Experimental mock-ups are conducted imitating container with threats among a complex packing as they may be encountered in reality. At the end, the significant advantages of the presented X-ray backscatter camera in the context of aviation and port security will be discussed. T2 - ECNDT 2014 - 11th European conference on non-destructive testing CY - Prague, Czech Republic DA - 06.10.2014 KW - Radiography KW - X-ray backscatter imaging KW - Irradiation geometry KW - Detection of dangerous materials KW - Security applications PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-322429 UR - https://www.ndt.net/?id=16432 SN - 1435-4934 VL - 19 IS - 12 SP - 1 EP - 8 PB - NDT.net CY - Kirchwald AN - OPUS4-32242 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kolkoori, Sanjeevareddy A1 - Wrobel, Norma A1 - Zscherpel, Uwe A1 - Ewert, Uwe T1 - New X-ray backscatter imaging technique for nondestructive testing of aerospace components N2 - Critical parts in aircraft manufacturing such as stringers are very commonly used in modern aircraft structures to resist the compressive loads caused by the aerodynamic effects. They are generally made-up of thin aluminium (Al) metal sheets and are one of the key components in the aircraft wings. Any defects in the stringer leads to weakening of the stiffness of the whole wing structure and consequently, failures may occur. Hence, the structural integrity of the stringers should be evaluated using reliable non-destructive testing (NDT) methods. Due to the complex shaped structure of the stringer, the one-sided access NDT method such as X-ray backscatter technique is more preferable for the non-destructive imaging. In this paper, we present a new X-ray backscatter technique to image the internal sections of the stringer with only a single-sided access. The whole object was inspected by changing the viewing direction of the X-ray backscatter camera. For the first time, the X-ray backscatter measurements were conducted using high-energy (> 0.5MeV) X-rays and proved the applicability of the present technique to inspect thick carbon-fiber laminated components. In order to improve the inspection time and image quality of the backscatter image, we used high-resolution (180ìm) digital detector arrays (DDAs). At the end, important applications of the presented X-ray backscatter technique to the aerospace industry are discussed. T2 - ECNDT 2014 - 11th European conference on non-destructive testing CY - Prague, Czech Republic DA - 06.10.2014 KW - X-ray backscatter imaging KW - Twisted-slit collimator KW - NDT KW - Digital detector array (DDA) KW - Stringer KW - Aerospace applications PY - 2014 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-322376 UR - https://www.ndt.net/?id=16431 SN - 1435-4934 VL - 19 IS - 12 SP - 1 EP - 8 PB - NDT.net CY - Kirchwald AN - OPUS4-32237 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -