TY - JOUR A1 - Schwettmann-Lui, Kim A1 - Nytus, Nina A1 - Weigel, Sandra A1 - Radenberg, Martin A1 - Stephan, Dietmar T1 - Effect of multiple-repeated aging and rejuvenation processes on bitumen properties evaluated with physical and chemical tests and multivariate analysis methods N2 - This paper presents laboratory experiments on repeated bitumen aging and rejuvenation processes to assess multiple reuse feasibility. Three 50/70 penetration-graded bitumen samples were reused with four different rejuvenators without adding virgin binder. The experiments continued until significant material changes, such as inhomogeneities and increased stickiness, prevented reliable characterization. After each rejuvenation and aging process, physical and chemical properties were analyzed, resulting in a comprehensive dataset. Results indicate that the reuse of pure rejuvenators, without incorporating virgin binder, is limited. Cyclic reuse depends heavily on the rejuvenator and its interaction with the binder. Of the four rejuvenators tested, two bio-based products enabled the maximum reuse of four cycles. Therefore, the rejuvenators used in this project are more suitable as additives to improve the physical properties of the bitumen for reuse rather than as substitutes for the binder. The datasets were further evaluated using multivariate analysis methods to construct statistical models for two use cases: In the first use case, the samples are classified by their aging condition. In the second use case, the samples are differentiated according to the rejuvenators. The models were successfully validated, providing a promising framework for the classification of unknown bitumen samples for reuse. KW - Bitumen KW - Aging KW - Rejuvenation KW - Multiple recycling KW - DSR measurements KW - Reuse KW - FTIR spectroscopy KW - Multivariate analysis methods PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-627563 DO - https://doi.org/10.1016/j.conbuildmat.2025.140734 SN - 1879-0526 VL - 472 SP - 1 EP - 16 PB - Elsevier Ltd. AN - OPUS4-62756 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Capitain, C. A1 - Schüßler, M. A1 - Bugsel, B. A1 - Zweigle, J. A1 - Vogel, Christian A1 - Leube, Peter A1 - Zwiener, C. T1 - Implementation of matrix-matched semiquantification of PFAS in AFFF-contaminated soil N2 - This study presents a novel semiquantification approach for nontarget screening (NTS), combining matrix-matched calibration and ionization class-specific average calibration curves (ACCs) to address the lack of analytical reference standards for most per- and polyfluoroalkyl substances (PFAS). Ionization class-specific ACCs for carboxylic and sulfonic acids, sulfonamides, and cationic PFAS result in high accuracy, with median absolute accuracy quotients below 2.27×. The approach was applied to soil impacted by aqueous film-forming foam (AFFF) contamination. A total of 96 tentatively identified PFAS were semiquantified in addition to 28 quantified compounds based on available standards. Semiquantified concentrations exceeded those of target analytes, demonstrating the critical role of this method in capturing broader PFAS contamination. In this case, validation against extractable organofluorine (EOF) showed a 102% closed mass balance. The innovative approach not only enables comprehensive PFAS contamination assessment in complex matrices but also expands the scope of the NTS for environmental monitoring, remediation, and risk assessment of AFFF-contaminated sites. KW - Per- and polyfluoroalkyl substances (PFAS) KW - Contaminated soil KW - Non-targeted analysis KW - Combustion ion chromatography PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-629445 DO - https://doi.org/10.1021/acs.est.4c14255 SN - 1520-5851 VL - 59 IS - 14 SP - 7338 EP - 7347 PB - American Chemical Society (ACS) CY - Columbus, Ohio AN - OPUS4-62944 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - McGonigle, Rebecca A1 - Glasgow, Jodie A1 - Houston, Catriona A1 - Cameron, Iain A1 - Homann, Christian A1 - Black, Dominic J. A1 - Pal, Robert A1 - MacKenzie, Lewis E. ED - MacKenzie, Lewis E. T1 - Autoclave reactor synthesis of upconversion nanoparticles, unreported variables, and safety considerations N2 - Autoclave reactors are widely used across chemical and biological sciences, including for the synthesis of upconversion nanoparticles (UCNPs) and other nanomaterials. Yet, the details of how autoclave reactors are used in such synthesis are rarely reported in the literature, leaving several key synthesis variables widely unreported and thereby hampering experimental reproducibility. In this perspective, we discuss the safety considerations of autoclave reactors and note that autoclaves should only be used if they are (a) purchased from reputable suppliers/manufacturers and (b) have been certified compliant with relevant safety standards. Ultimately, using unsuitable autoclave equipment can pose a severe physical hazard and may breach legal safety requirements. In addition, we highlight several parameters in autoclave synthesis that should be reported as standard to maximise the reproducibility of autoclave synthesis experiments across materials and chemistry research. We encourage users of autoclave synthesis vessels to: (1) adopt high-safety autoclaves and (2) report the many experimental variables involved to enhance experimental reproducibility. KW - Reference material KW - Nano KW - Particle KW - Shell KW - Fluorescence KW - Lifetime KW - Decay kinetics KW - Synthesis KW - Quality assurance KW - Method KW - Energy transfer KW - Upconversion KW - Autoclave synthesis KW - Data comparability PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-625672 DO - https://doi.org/10.1038/s42004-025-01415-3 VL - 8 IS - 1 SP - 1 EP - 7 PB - Springer Science and Business Media LLC AN - OPUS4-62567 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Poka, Konstantin A1 - Ali, Sozol A1 - Saeed, Waleed A1 - Merz, Benjamin A1 - Epperlein, Martin A1 - Hilgenberg, Kai T1 - Quality assurance via a cyber physical system of a PBF-LB/M machine N2 - Powder Bed Fusion with Laser Beam of Metals (PBF-LB/M) faces challenges in reproducibility and quality assurance, even for widely applied alloys like AlSi10Mg. This work introduces a digital provenance framework for PBF-LB/M, showcased through the EOS M 300–4 multi-laser machine. An Extract, Transform, Load (ETL) pipeline autonomously captures machine data, including scan vectors as well as process signals, and organizes them into a Digital Shadow (DS). The DS is further extended by external data sources, such as Melt Pool Monitoring (MPM), to enable comprehensive analysis and root cause identification. This approach ensures continuous data representation and facilitates the development of new quality metrics. Moreover, the framework enhances quality assurance and traceability, supports compliance with industry standards, and improves productivity. It also enables more precise cost calculations and predictive maintenance. By addressing these challenges, the framework is essential for advancing PBF-LB/M in industrial applications, achieving greater consistency and scalability in production. KW - PBF-LB/M KW - Data driven quality assurance KW - Data engineering KW - Digital shadow PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-625187 DO - https://doi.org/10.1007/s40964-025-00978-w SN - 2363-9520 VL - 10 IS - 3 SP - 1771 EP - 1783 PB - Springer Science and Business Media LLC AN - OPUS4-62518 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schackmann, Oliver A1 - Márquez Reyes, Octavio A. A1 - Memmolo, Vittorio A1 - Lozano, Daniel A1 - Prager, Jens A1 - Moll, Jochen A1 - Kraemer, Peter T1 - Machine learning strategies with ensemble voting for ultrasonic damage detection in composite structures under varying temperature or load conditions N2 - In recent years, the development of machine learning (ML) techniques has led to significant progress in the field of structural health monitoring with ultrasonic-guided waves. However, a number of challenges still need to be resolved for reliable operation in realistic settings. In this work, we consider the complex problem of experimental damage detection under varying temperature or load conditions where damage locations are not included in the training set. The ML techniques proposed here include supervised and unsupervised methods originally developed for image and time series classification combined with ensemble voting. A performance demonstration of the ML techniques is presented using benchmark datasets from the open-guided waves platform. The unsupervised approach is then applied to a new dataset from an experimental campaign carried out on a composite over-wrapped pressure vessel used for hydrogen storage with real defects. Results show that ensemble voting enables the effective combination of the predictions of multiple transducer pairs, even with a limited number of strong individual classifiers. When applied to unsupervised learning, this returns high accuracy also when real damage over the structure is considered. KW - Structural-Health-Monitoring KW - Ultrasonic guided waves PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-631571 DO - https://doi.org/10.1177/14759217251333066 SN - 1741-3168 SP - 1 EP - 19 PB - Sage Publications AN - OPUS4-63157 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hendricks, A. A1 - Phillips, T. K. A1 - Engl, T. A1 - Plarre, Rudy A1 - Martinson, V. G. T1 - The bacterial microbiome in spider beetles and deathwatch beetles N2 - The beetle family Ptinidae contains a number of economically important pests, such as the cigarette beetle Lasioderma serricorne, the drugstore beetle Stegobium paniceum, and the diverse spider beetles. Many of these species are stored product pests, which target a diverse range of food sources, from dried tobacco to books made with organic materials. Despite the threat that the 2,200 species of Ptinidae beetles pose, fewer than 50 have been surveyed for microbial symbionts, and only a handful have been screened using contemporary genomic methods. In this study, we screen 116 individual specimens that cover most subfamilies of Ptinidae, with outgroup beetles from closely related families Dermestidae, Endecatomidae, and Bostrichidae. We used 16S ribosomal RNA gene amplicon data to characterize the bacterial microbiomes of these specimens. The majority of these species had never been screened for microbes. We found that, unlike in their sister family, Bostrichidae, that has two mutualistic bacteria seen in most species, there are no consistent bacterial members of ptinid microbiomes. For specimens which had Wolbachia infections, we did additional screening using multilocus sequence typing and showed that our populations have different strains of Wolbachia than noted in previous publications. KW - Sodalis KW - Ptinidae KW - Anobiidae KW - Bostrichidae KW - Dermestidae KW - Bostrichoidea KW - Wolbachia PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-631564 DO - https://doi.org/10.1128/spectrum.01981-24 SN - 2165-0497 VL - 13 IS - 5 SP - 1 EP - 14 AN - OPUS4-63156 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Amano, Kofi Owusu Ansah A1 - Tschirschwitz, Rico A1 - Gimadieva, Elena A1 - Köhler, Florian A1 - Krause, Ulrich T1 - Thermal runaway and explosibility of the gas release from 18650 sodium-ion cells of NFM chemistry N2 - The present study investigates the thermal runaway behaviour and explosibility of the gas mixture released from sodium-ion batteries (SIBs). A total of 30 tests comprising two test series were performed using 18650 SIBs with a NaNi1/3Fe1/3Mn1/3O2 (NFM) chemistry. The cells of SOC level = 0 %, 25 %, 50 %, 75 % and 100 % were subjected to thermal abuse inside a 10 L pressurized reaction vessel. In test series 1, the tests were performed in an air atmosphere. In test series 2, an inert atmosphere was used. First, the total amount of gas released from the SIBs was calculated based on the temperature and pressure measured in the reaction vessel. Subsequently, a gas composition analysis was performed using a Fourier-transformed infrared (FTIR) spectrometer. This study revealed that the thermal runaway in SIBs could be categorized into four phases. At the onset of thermal runaway, the thermal runaway-induced explosion of the cells resulted in a rate of temperature rise ranging from 2 K/s to 70 K/s. The investigation further revealed a peak reaction temperature of 415 ◦C and a maximum pressure of 4 bar could be reached at thermal runaway in the 10 L vessel. The gas release of up to 5 ± 0.3 L (4 ± 0.2 L/Ah, 1.3 ± 0.1 L/Wh) from test series 1 and 2.4 ± 0.2 L (2 ± 0.1 L/Ah, 0.53 ± 0.04 L/Wh) from test series 2 showed a dependence on SOC and failure environment used. By applying Le Chatelier's mixing rule, the measured gas release from the air atmosphere showed a calculated lower explosion limit and upper explosion limit values of 4.8 % and 24 % in volume fraction, respectively. KW - Sodium-ion battery KW - Thermal runaway KW - Gas release KW - Gas explosion KW - Explosion limit PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-631782 DO - https://doi.org/10.1016/j.est.2025.116614 SN - 2352-152X VL - 122 SP - 1 EP - 16 PB - Elsevier Ltd. AN - OPUS4-63178 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Jafari, Abbas A1 - Vlachas, K. A1 - Chatzi, E. A1 - Unger, Jörg F. T1 - A Bayesian framework for constitutive model identification via use of full field measurements, with application to heterogeneous materials N2 - In this paper, we present a Bayesian framework for the identification of the parameters of nonlinear constitutive material laws using full-field displacement measurements. The concept of force-based Finite Element Model Updating (FEMU-F) is employed, which relies on the availability of measurable quantities such as displacements and external forces. The proposed approach particularly unfolds the advantage of FEMU-F, as opposed to the conventional FEMU, by directly incorporating information from full-field measured displacements into the model. This feature is well-suited for heterogeneous materials with softening, where the localization zone depends on the random microstructure. Besides, to account for uncertainties in the measured displacements, we treat displacements as additional unknown variables to be identified, alongside the constitutive parameters. A variational Bayesian scheme is then employed to identify these unknowns via approximate posteriors under the assumption of multivariate normal distributions. An optimization problem is then formulated and solved iteratively, aiming to minimize the discrepancy between true and approximate posteriors. The benefit of the proposed approach lies in the stochastic nature of the formulation, which allows to tackle uncertainties related to model parameters and measurement noise. We verify the efficacy of our proposed framework on two simulated examples using gradient damage model with a path-dependent nonlinear constitutive law. Based on a nonlocal equivalent strain norm, this constitutive model can simulate a localized damage zone representing softening and cracking. The first example illustrates an application of the FEMU-F approach to cracked structures including sensitivity studies related to measurement noise and parameters of the prior distributions. In this example, the variational Bayesian solver demonstrates a sizable advantage in terms of computational efficiency compared to a traditional least-square optimizer. The second example demonstrates a sub-domain analysis to tackle challenges associated with limited domain knowledge such as uncertain boundary conditions. KW - Constitutive model identification KW - Full-field measurements KW - Variational Bayes KW - Force-based finite element model updating KW - FEMU-F PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-615476 DO - https://doi.org/10.1016/j.cma.2024.117489 SN - 1879-2138 VL - 433 IS - Part A SP - 1 EP - 32 PB - Elsevier B.V. AN - OPUS4-61547 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pfennig, A. A1 - Simkin, Roman T1 - Identifying the initial corrosion fatigue failure based on dropping electrochemical potential N2 - The corrosion fatigue of duplex stainless-steel X2CrNiMoN22-5-3 can be determined by purely alternating axial cyclic load to failure using hour-glass shaped specimens. The experimental setup comprises a corrosion chamber allowing for the circulation of an aquifer electrolyte heated to 369 K simulating a carbon capture and storage as well as geothermal power plant environment. During engineering of a carbon storage site or geothermal power plant, it may be crucial to determine the failure onset of a component beforehand. Therefore, an algorithm with 93.3% reliability was established based on splitting the measured potential values into ten time series with a capacity of ten values. The failure of corrosion fatigue specimens in a geothermal environment correlates to the drop of the curves of the electrochemical potential which is measured simultaneously within the corrosion chamber. Crack initiation was, therefore, successfully derived from the electrochemical potential. KW - Corrosion fatigue KW - Surface corrosion KW - CO2 KW - Crack initiation KW - Geothermal energy production PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-629310 DO - https://doi.org/10.3390/app15010403 SN - 2076-3417 VL - 15 IS - 1 SP - 1 EP - 15 PB - MDPI CY - Basel AN - OPUS4-62931 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kumar, Sumit A1 - Swaminathan, Srinivasan A1 - Hesse, Rene A1 - Goldbeck, Hennig A1 - Ding, Wenjin A1 - Bonk, Alexander A1 - Bauer, Thomas T1 - Understanding the effect of oxide ions on Solar Salt chemistry and corrosion mechanism of 316L stainless steel at 600 °C N2 - Solar Salt (60 wt% NaNO3, 40 wt% KNO3), used in Concentrated Solar Power (CSP) Thermal Energy Storage (TES) technology, can decompose into various products at elevated temperatures, with oxide ions being one of the known corrosive byproducts. The study mimics Solar Salt aging by intentionally adding sodium peroxide (Na2O2) and sodium oxide (Na2O) at concentrations of 0.005–0.33 wt% to investigate their role in the corrosion of austenitic stainless steel at 600 °C in typical operating conditions. Salt chemistry (nitrite, nitrate, oxide ions, and metal cations) was analyzed every 24 h, and steel corrosion after 168 h was assessed by weight change, corrosion rate, phase analysis, and cross-sectional morphology. Results reveal that at or above 0.135 wt% added Na2O2/Na2O leads to a quasi-steady-state equilibrium of oxide ions in the salt. Interestingly, at these concentrations, the presence of steel further decreases oxide ion concentration. Furthermore, above 0.135 wt%, the corrosion rate increases significantly, along with increased spallation, porosity and disintegration of the corrosion layer, forming a non-protective layer. This study highlights the critical role of oxide ions in the corrosion process. KW - Solar Salt KW - High temperature corrosion KW - Thermal Energy Storage KW - Alkali oxides KW - Austenitic stainless steel PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-628463 DO - https://doi.org/10.1016/j.corsci.2025.112849 SN - 1879-0496 VL - 249 SP - 1 EP - 17 PB - Elsevier Ltd. AN - OPUS4-62846 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - John, Elisabeth A1 - Jakob, Cordula A1 - Pott, Ursula A1 - Sando, Mona T1 - Repeatability and reproducibility challenges of isothermal heat flow calorimetry with in situ mixing N2 - Isothermal heat flow calorimetry evaluates heat development during binder reactions. It distinguishes between in situ calorimetry, where mixing occurs within the device, and ex situ calorimetry, involving externally mixed samples. Despite ex situ calorimetry being a standard method in binder research, in situ calorimetry is underutilized. This paper aims to promote its adoption by summarizing challenges related to repeatability and reproducibility and offering solutions. The initial section addresses repeatability issues caused by preventable errors, providing a structured guide for experimental design. It was found that water leakage had minimal impact, and sample size is crucial for data robustness. The second section examines operational challenges, revealing that frictional heating, affecting recorded heat, can be minimized with an optimized mixing protocol. The final part highlights that significant errors in measured data stem from signal delay and heat loss, offering methods to correct these issues for improved reproducibility in in situ calorimetric experiments. KW - In situ calorimetry PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-628431 DO - https://doi.org/10.1016/j.cemconres.2025.107872 SN - 1873-3948 VL - 194 SP - 1 EP - 11 PB - Elsevier Ltd. AN - OPUS4-62843 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Baeßler, Matthias A1 - Simon, Patrick T1 - Ballasted track on vibrating bridge decks: physical mechanisms, empirical findings, and a proposal for assessment N2 - This paper summarizes the key findings and physical mechanisms and provides information on open questions and the assessment of railway bridge superstructure vibrations. Bridges are classic disruption points on a railway track. If bridge superstructures are dynamically excited by train traffic, the vertical accelerations of the track must be considered. For a ballasted track, this can lead to the destabilization of the ballast track, as the bridge superstructure acts like a vibrating table. In this respect, the paper explains in more detail what is meant by destabilization, when this destabilization occurs and how various influencing parameters such as acceleration amplitude, the vibration sequence and frequency affect its occurrence. In the InBridge4EU project, gaps in knowledge such as the effect of single impulse loads are being investigated experimentally. A new test facility has been set up for this purpose, the initial results of which are presented here. An essential element in the assessment of this scenario is the stability of the track under high compression forces with simultaneous dynamic excitation of the superstructure. A new approach for the assessment of bridge vibrations with respect to lateral stability is presented. KW - Railway bridge dynamics KW - Bridge deck acceleration KW - Ballast destabilization KW - Lateral track stability KW - Track buckling PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-630972 DO - https://doi.org/10.1142/S0219455425400243 SN - 0219-4554 SN - 1793-6764 IS - 2540024 SP - 1 EP - 27 PB - World Scientific CY - Singapore AN - OPUS4-63097 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Willms, Thomas A1 - Kryk, Holger A1 - Hampel, Uwe T1 - An improved method for the analysis of the reaction products of the partial isobutane oxidation by gas chromatography using a green solvent N2 - In the present work, an improved GC/MS method for the analysis of the reaction products of the non-catalytic partial oxidation of isobutane at a starting temperature of 25°C has been developed and compared to a previously published method. Two green GC-solvents (dimethyl carbonate (DMC), diethyl carbonate (DEC)) and several internal standards (hexane, benzene, toluene, DEC) have been tested. The separation of the products at low retention times (methanol, isobutane, isobutene) could be significantly improved. For the liquid main products t-butyl hydroperoxide (TBHP), di-t-butyl peroxide (DTBP), t-butanol (TBA), propanone and most trace products (isopropanol, isobutanal, methyl formate, isopropyl formate, t-butyl formate and some acetates – 24 compounds in total), a coefficient of determination CoD > 0.999 has been achieved. For all weighing and GC/MS measurements uncertainties have been calculated. The peaks of the peak pair t-butyl formate (CoD >0.999) and isobutanol (CoD >0.99), have been simulated and used for calibrations. DEC gave a decomposition of TBHP on the column. With DMC, a problem of peak purity of TBHP appeared but could be resolved. The use of the green solvent DMC, compared to also studied traditional solvents like heptane and toluene, proved to be very beneficial, since it also permitted to determine polar compounds, e. g. carbon dioxide and formic acid. KW - GC/MS KW - Green solvent KW - Method development KW - Peroxide KW - Measurement uncertainties KW - Oxidation products KW - Simulation PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-632026 DO - https://doi.org/10.1016/j.chroma.2025.465892 SN - 0021-9673 VL - 1753 SP - 1 EP - 16 PB - Elsevier CY - Amsterdam AN - OPUS4-63202 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Xu, Q. A1 - Szymoniak, Paulina A1 - Kolmangadi, Mohamed A. A1 - Yang, Z. A1 - Wang, S. A1 - Gao, Y. A1 - Shang, J. A1 - Hunger, J. A1 - Aldiyarov, A. A1 - Schönhals, Andreas A1 - Ge, Y. A1 - Qi, Z. T1 - Molecular engineering of supramolecular polymer adhesive with confined water and a single crown ether N2 - Here, we report a water-induced supramolecular polymer built from confined structural water and an intrinsic amphiphilic macrocyclic self-assembly in a nanophase separated structure. The newly designed crown ether macrocycle, featuring strong hydrophilic hydrogen bonding receptor selenoxide and a synergistical hydrophobic selenium-substituted crown core, confines the structural water in a segregated, interdigitated architecture. Although water molecules typically freeze around 0 °C, the confined structural water in this supramolecular polymer remains in a liquid-like state down to 80 °C. Previous studies suggest that multiple crown ether units are needed to generate structural water. However, here, one unit is sufficient to control the formation and disappearance of structural water and consequent supramolecular polymerization. Typically, the DC conductivity of water shows Arrhenius temperature dependency (lnσDC ∝ 1/T). In contrast, this new crown unit maintains water in confined states, which exhibit a Vogel/Fulcher/Tammann behavior (lnσDC ∝ 1/(T-T0)) at temperatures above the glass transition temperature. Moreover, this water-induced supramolecular polymer exhibits remarkable adhesion properties to hydrophilic surfaces and maintains tough adhesion at low temperatures. These findings show how a single small macrocycle can govern the complex structure and functionality of water in supramolecular systems. KW - Supramolecular polymerization PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-623631 DO - https://doi.org/10.1039/D4SC06771A SN - 2041-6539 VL - 16 SP - 1 EP - 9 PB - RSC AN - OPUS4-62363 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Nandish, Ranjith A1 - Knaust, Christian A1 - Zehfuß, Jochen T1 - Numerical Investigations of a Large Fire Exposure Crib Test—Presenting Different Pyrolysis Modelling Methodologies and Numerical Results N2 - ABSTRACTThe need for numerical‐based approaches to investigate the fire behaviour in buildings with combustible components is growing due to the increasing use of timber by the construction industry to meet the ‘Climate Action Plan 2050’. This requires consideration of the complex kinetic processes that take place during the burning of the wood in the numerical models. This is accomplished by using computational fluid dynamics (CFD) to numerically model the material pyrolysis and combustion processes. This article presents three different approaches for simulating the behaviour of a wood crib fire using the fire dynamics simulator (FDS). These approaches are based on either prescribing the burning rate of the wood directly from the physical experiments or using the kinetic parameters to govern the underlying processes, such as pyrolysis. Wooden crib fire experiments carried out by the RISE Research Institute in Sweden inside the combustion chamber that were used to validate all the methods. The numerical results from the method, that utilised the experimentally determined burning rate, were in good agreement with the experimental results, with a maximum deviation of 6% in the case of HRR. On the other hand, the model that needs kinetic parameters as its input has shown maximum discrepancies of 12% and 33% compared to experimental results. These methods are sensitive to the input parameters and the extent of dependency needs further investigation. KW - Pyrolysis KW - Wood combustion KW - Wood fire loads KW - Wooden buildings PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-626567 DO - https://doi.org/10.1002/fam.3287 SN - 1099-1018 VL - 49 IS - 4 SP - 371 EP - 387 PB - John Wiley & Sons Ltd. AN - OPUS4-62656 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zhu, Jiangchao A1 - Madia, Mauro A1 - Schurig, Michael A1 - Kruse, Julius A1 - Conrad, Fabian A1 - Schlums, Hartmut A1 - Kontermann, Christian A1 - Zerbst, Uwe T1 - On the use of representative specimens for the structural integrity assessment of safety-relevant rotating components N2 - Safety-relevant components, for which a failure in service could have catastrophic consequences, are usually designed for extremely low probability of failure and they are subjected to stringent part qualification procedures according to guidelines set by regulatory agencies. Manufacturers are often forced to perform tests on full scale or scaled components to ensure the structural integrity under defined loading conditions, which usually implies a huge experimental and financial effort. Therefore, companies try to develop new strategies such as digital twins, which allow to massively reduce costs, without compromising safety. This work presents a new quasi-static testing and assessment concept, the main idea of which is to replace, or at least reduce, the experimental testing on components by testing specimens representative of the component. Fracture mechanics specimens have been designed iteratively by numerical simulations to match the stress state at the crack-tip of the maximum permissible defect defined by regulatory agencies for the component. Potentially, the major benefit of the proposed approach is that the tests can be performed on conventional laboratory testing machines. The effectiveness of the methodology is demonstrated in case of the structural integrity assessment of a Ni-base superalloy aero-engine turbine disk at overspeed conditions. KW - Structural integrity KW - Turbine disk KW - Burst KW - Fracture mechanics KW - Representative specimens KW - Quasi-static testing PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-624208 DO - https://doi.org/10.1016/j.engfracmech.2024.110710 SN - 0013-7944 VL - 314 SP - 1 EP - 23 PB - Elsevier Ltd. AN - OPUS4-62420 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Martin, T. A1 - Zimmermann, E. A1 - Klitzsch, N. A1 - Hördt, A. A1 - Huisman, J. A. A1 - Radic, T. A1 - Kruschwitz, Sabine T1 - Round-robin test of SIP laboratory measurements using electrical test networks N2 - This study presents the results of an interlaboratory test designed to evaluate the accuracy of spectral induced polarization (SIP) measurements using controlled electrical test networks. The study, conducted in Germany since 2006, involved 12 research institutes, six different impedance measurement devices and four types of electrical test networks specifically designed to evaluate phase shift errors in SIP measurements. The test networks, with impedances ranging from 100 to 150 kΩ, represent high-impedance samples with different phase characteristics, and pose the measurement challenges typical of such samples, including high contact impedances and parasitic capacitances. Four key findings emerged from the study: (1) Impedance measurements across all devices showed deviations within 1 per cent over a wide frequency range (0.001–1000 Hz); (2) phase errors remained below 1 mrad up to 100 Hz for most devices, but increased at higher frequencies due to parasitic capacitances and electromagnetic coupling effects; (3) lab-specific instruments have lower phase errors than field instruments when used in a laboratory environment, primarily due to the effects of long cables and too low input impedances of the field instruments; and (4) short cables and driven shielding technology effectively minimized parasitic capacitance and improved measurement accuracy. The study highlights the usefulness of test networks in assessing the accuracy of SIP measurements and raises awareness of the various factors influencing the quality of SIP data. KW - Induced polarization KW - Electrical properties KW - Electrical resistivity tomography (ERT) PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-631522 DO - https://doi.org/10.1093/gji/ggaf153 SN - 0956-540X VL - 242 IS - 1 SP - 1 EP - 13 PB - Oxford University Press (OUP) AN - OPUS4-63152 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schraa, Lucas A1 - Rodricks, Carol A1 - Kalinka, Gerhard A1 - Roetsch, Karl A1 - Scheffler, Christina A1 - Sambale, Anna A1 - Uhlig, Kai A1 - Stommel, Markus A1 - Trappe, Volker T1 - Characterisation and Modelling of the Fibre-Matrix Interface of Short Fibre Reinforced Thermoplastics using the Push-Out Technique N2 - This study investigates the suitability of the single fibre push-out (SFPO) test for the determination of the interfacial shear strength (IFSS) of injection moulded short fibre reinforced thermoplastics. It includes a detailed description of the required sample preparation steps and the boundary conditions of the SFPO setup. Experimental SFPO tests were carried out on PA66 GF, PPA GF35 and PA6 GF50 materials. Furthermore, a finite element model was set up to simulate the behaviour of these materials during this test. The numerical results showed that the inhomogeneous stress distribution in the fibre-matrix interphase during the test causes the measured apparent IFSS to underestimate the true strength of the interphase. The simulations put the experimental results into perspective and provide valuable information for the further development of the test setup. This study therefore not only provides new insights into the interphase strength of injection moulded short fibre reinforced thermoplastics, but also an insight into local load conditions during testing and thus an indication of the true IFSS. KW - GFRP KW - Interface KW - fibre matrix bond KW - single fibre push-out PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-626087 DO - https://doi.org/10.1016/j.compositesb.2025.112317 SN - 1879-1069 VL - 297 SP - 1 EP - 8 PB - Elsevier Ltd. CY - Niederlande AN - OPUS4-62608 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Duarte Bernardino, Carolina A1 - Lee, Mihyun A1 - Ren, Qun A1 - Ruehle, Bastian T1 - Facile Spray-Coating of Antimicrobial Silica Nanoparticles for High-Touch Surface Protection N2 - The rising threat from infectious pathogens poses an ever-growing challenge. Metal-based nanomaterials have gained a great deal of attention as active components in antimicrobial coatings. Here, we report on the development of readily deployable, sprayable antimicrobial surface coatings for high-touch stainless steel surfaces that are ubiquitous in many healthcare facilities to combat the spread of pathogens. We synthesized mesoporous silica nanoparticles (MSNs) with different surface functional groups, namely, amine (MSN-NH2), carboxy (MSN-COOH), and thiol groups (MSN-SH). These were chosen specifically due to their high affinity to copper and silver ions, which were used as antimicrobial payloads and could be incorporated into the mesoporous structure through favorable host−guest interactions, allowing us to find the most favorable combinations to achieve antimicrobial efficacy against various microbes on dry or semidry high-touch surfaces. The antimicrobial MSNs were firmly immobilized on stainless steel through a simple two-step spray-coating process. First, the stainless steel surfaces are primed with sprayable polyelectrolyte solutions acting as adhesion layers, and then, the loaded nanoparticle dispersions are spray-coated on top. The employed polyelectrolytes were selected and functionalized specifically to adhere well to stainless steel substrates while at the same time being complementary to the MSN surface groups to enhance the adhesion, wettability, homogeneity, and stability of the coatings. The antimicrobial properties of the nanoparticle suspension and the coatings were tested against three commonly found pathogenic bacteria, Staphylococcus aureus, Pseudomonas aeruginosa, and Escherichia coli, as well as a fungal pathogen, Candida albicans. Especially MSN-SH loaded with silver ions showed excellent antimicrobial efficacy against all tested pathogens under application-relevant, (semi)dry conditions. The findings obtained here facilitate our understanding of the correlation between the surface properties, payloads, and antimicrobial activity and show a new pathway toward simple and easily deployable solutions to combat the spread of pathogens with the help of sprayable antimicrobial surface coatings. KW - Mesoporous silica nanoparticles KW - Thin films KW - Antimicrobial coatings KW - Spray-coating KW - Infectious diseases KW - Pathogen transmission KW - High-touch surfaces PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-626269 DO - https://doi.org/10.1021/acsami.4c18916 SN - 1944-8252 SP - 1 EP - 13 PB - ACS Publications CY - Washington, DC AN - OPUS4-62626 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mishmastnehi, Moslem A1 - Stawski, Tomasz M. A1 - Eftekhari, Negar A1 - Schneider, Kathrin P. A1 - Vaccaro, Carmela A1 - Aghajani, Iman A1 - Grbanovic, Ana Marija A1 - Korn, Lorenz T1 - Unveiling the craftsmanship and knowledge behind iranian stuccoes (11th–14th centuries): New insights from an archaeometric perspective N2 - Gypsum-based stucco decorations of 47 monuments in Iran, from the Seljuq to the Ilkhanid period (11th-14th centuries), were studied by multimodal analytical methods, including X-ray diffraction, X-ray fluorescence, scanning electron microscopy and image analysis to evaluate their composition properties. The assessment of results shows that stucco masters in those periods exerted control over the setting process of the gypsum-paste and its microstructure by adjusting water-to-plaster ratio, fine-clay addition, and by means of mechanical processing. Furthermore, the presence of anhydrite in the composition of stucco decorations located in the hot-desert climate of Iran provides evidence for the probability of gypsum-anhydrite transition, which has technical and preservation consequences for this less-investigated type of cultural materials. KW - Gypsum KW - Diffraction KW - Anhydrite KW - Calcium sulfate PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-628406 DO - https://doi.org/10.1016/j.jas.2025.106199 SN - 1095-9238 VL - 177 SP - 1 EP - 13 PB - Elsevier B.V. AN - OPUS4-62840 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Senbill, Haytham A1 - Gangan, Amr A1 - Saeed, Ahmed M. A1 - Gad, Mohammed E. A1 - Zeb, Jehan A1 - Fahmy, Alaa T1 - Effects of copper/graphene oxide core-shell nanoparticles on Rhipicephalus ticks and their detoxification enzymes N2 - Nanopesticides have been recently introduced as novel pesticides to overcome the drawbacks of using traditional synthetic pesticides. The present study evaluated the acaricidal activity of Copper/Graphene oxide core-shell nanoparticles against two tick species, Rhipicephalus rutilus and Rhipicephalus turanicus. The Copper/Graphene oxide core-shell nanoparticles were synthetized through the solution plasma (SP) method under different conditions. The nanoparticles synthesized at 180 W and 45 min were highly toxic to Rh. rutilus and Rh. turanicus, with 50% lethal concentration (LC50) values of 248.1 and 195.7 mg ml−1, respectively, followed by those which were synthesized at 120 W/30 mins (LC50 = 581.5 and 526.5 mg ml−1), 120 W/15 mins (LC50 = 606.9 and 686.7 mg ml−1), and 100/45 mins (LC50 = 792.9 and 710.7 mg ml−1), after 24 h of application. The enzyme assays revealed that 180 W/45 min treatment significantly inhibited the activity of acetylcholinesterase (115 ± 0.81 and 123 ± 0.33 U/ mg protein/min) and superoxide dismutase (290 ± 0.18 and 310 ± 0.92 U/ mg protein/min) in Rh. rutilus and Rh. turanicus, respectively, as compared with the negative control. The results also revealed a significantly increased catalase activity (895 ± 0.37 and 870 ± 0.31 U/ mg protein/min) in Rh. rutilus and Rh. turanicus, respectively. The above results indicated that Copper/Graphene oxide core-shell nanoparticles could be a promising alternatives for the management of ticks. KW - Copper/graphene oxide KW - Nanopesticides KW - Rhipicephalus rutilus KW - Rhipicephalus turanicus KW - Acetylcholinesterase KW - Antioxidants PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-629359 DO - https://doi.org/10.1038/s41598-025-86560-4 SN - 2045-2322 VL - 15 SP - 1 EP - 12 PB - Springer Nature CY - London AN - OPUS4-62935 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Ruehle, Bastian T1 - Natural language processing for automated workflow and knowledge graph generation in self-driving labs N2 - Natural language processing with the help of large language models such as ChatGPT has become ubiquitous in many software applications and allows users to interact even with complex hardware or software in an intuitive way. The recent concepts of Self-Driving Labs and Material Acceleration Platforms stand to benefit greatly from making them more accessible to a broader scientific community through enhanced user-friendliness or even completely automated ways of generating experimental workflows that can be run on the complex hardware of the platform from user input or previously published procedures. Here, two new datasets with over 1.5 million experimental procedures and their (semi)automatic annotations as action graphs, i.e., structured output, were created and used for training two different transformer-based large language models. These models strike a balance between performance, generality, and fitness for purpose and can be hosted and run on standard consumer-grade hardware. Furthermore, the generation of node graphs from these action graphs as a user-friendly and intuitive way of visualizing and modifying synthesis workflows that can be run on the hardware of a Self-Driving Lab or Material Acceleration Platform is explored. Lastly, it is discussed how knowledge graphs – following an ontology imposed by the underlying node setup and software architecture – can be generated from the node graphs. All resources, including the datasets, the fully trained large language models, the node editor, and scripts for querying and visualizing the knowledge graphs are made publicly available. KW - Natural Language Processing KW - Large Language Models KW - Self-Driving Labs KW - Materials Acceleration Platforms KW - Workflows KW - Nanomaterials KW - Advanced Materials PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-631947 UR - https://github.com/BAMresearch/MAPz_at_BAM/tree/main/Minerva-Workflow-Generator DO - https://doi.org/10.1039/d5dd00063g SN - 2635-098X SP - 1 EP - 10 PB - Royal Society of Chemistry (RSC) AN - OPUS4-63194 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bos, Freek A1 - Menna, Constantino A1 - Robens-Radermacher, Annika A1 - Wolfs, Rob A1 - Roussel, Nicolas A1 - Lombois-Burger, Hélène A1 - Baz, Bilal A1 - Weger, Daniel A1 - Nematollahi, Behzad A1 - Santhanam, Manu A1 - Zhang, Yamei A1 - Bhattacherjee, Shantanu A1 - Jia, Zijian A1 - Chen, Yu A1 - Mechtcherine, Viktor T1 - Mechanical properties of 3D printed concrete: a RILEM TC 304-ADC interlaboratory study — approach and main results N2 - To show compliance to structural engineering codes and implement quality control measures, it is critical to obtain reliable mechanical properties of the materials in question. For conventional cast and precast concrete, the experimental procedures and relationships between mechanical properties, the material composition, and the production methods are globally known, but for 3D concrete printing (3DCP), these relations have not yet been established. Previous studies have shown little consistency in results, and the underlying experimental methods have not been established broadly. There is an urgent need to address these issues as the application of 3DCP in practice projects is growing rapidly. Therefore, RILEM TC 304-ADC: Assessment of Additively Manufactured Concrete Materials and Structures has set up a large interlaboratory study into the mechanical properties of 3D printed concrete. This paper presents key elements of the experimental approach detailed in the Study Plan and the supporting considerations. Furthermore, it reports on the response, consisting of 34 contributions from 30 laboratories, detailing global coverage, properties of the applied mixture designs and characteristics of the printing facilities that have been used. Subsequently, some fundamental results from compression, flexural, and E-modulus testing are presented and—considering cast specimens as a reference—discussed. On average, a reduction in strength was found in compression and E-modulus (all tested orientations). For flexure, on the other hand, an increase was found in two testing orientations, while a decrease was observed in the third orientation. Importantly, even though the applied experimental methods were found to be reasonably appropriate to obtain the required data, the differences found between individual contributions are significant and sometimes non-consistent, suggesting that testing on specific material-facility combinations is necessary to reliably determine the mechanical properties of objects produced from them. Furthermore, a theoretical framework needs to be developed to further explain the variations that were observed. Extensive analyses of all acquired data are out of the scope of this contribution, but presented in two associated papers, whereas a third presents the data management approach used to process the approximately 5,000 test results. KW - 3D printed concrete KW - 3DCP KW - Mechanical properties KW - Interlaboratory study PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-634631 DO - https://doi.org/10.1617/s11527-025-02686-x VL - 58 IS - 5 SP - 1 EP - 29 PB - Springer Nature AN - OPUS4-63463 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Riebesell, Janosh A1 - Goodall, Rhys E. A. A1 - Benner, Philipp A1 - Chiang, Yuan A1 - Deng, Bowen A1 - Ceder, Gerbrand A1 - Asta, Mark A1 - Lee, Alpha A. A1 - Jain, Anubhav A1 - Persson, Kristin A. T1 - A framework to evaluate machine learning crystal stability predictions N2 - The rapid adoption of machine learning in various scientific domains calls for the development of best practices and community agreed-upon benchmarking tasks and metrics. We present Matbench Discovery as an example evaluation framework for machine learning energy models, here applied as pre-filters to first-principles computed data in a high-throughput search for stable inorganic crystals. We address the disconnect between (1) thermodynamic stability and formation energy and (2) retrospective and prospective benchmarking for materials discovery. Alongside this paper, we publish a Python package to aid with future model submissions and a growing online leaderboard with adaptive user-defined weighting of various performance metrics allowing researchers to prioritize the metrics they value most. To answer the question of which machine learning methodology performs best at materials discovery, our initial release includes random forests, graph neural networks, one-shot predictors, iterative Bayesian optimizers and universal interatomic potentials. We highlight a misalignment between commonly used regression metrics and more task-relevant classification metrics for materials discovery. Accurate regressors are susceptible to unexpectedly high false-positive rates if those accurate predictions lie close to the decision boundary at 0 eV per atom above the convex hull. The benchmark results demonstrate that universal interatomic potentials have advanced sufficiently to effectively and cheaply pre-screen thermodynamic stable hypothetical materials in future expansions of high-throughput materials databases. KW - Machine Learning KW - Interatomic Potentials PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-637139 DO - https://doi.org/10.1038/s42256-025-01055-1 SN - 2522-5839 VL - 7 IS - 6 SP - 836 EP - 847 PB - Springer Science and Business Media LLC AN - OPUS4-63713 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Szymoniak, Paulina A1 - Juranyi, F. A1 - Kruteva, M. A1 - Zorn, R. A1 - Schönhals, Andreas T1 - Low-Frequency Vibrational Density of States of Nanophase- Separated Poly(n‑alkyl methacrylate)s: Confined Phonons and Relationship to Specific Heat N2 - This study investigates the low-frequency vibrational Density of states of nanophase-separated poly(n-alkyl methacrylate)s (PnMAs) and its relationship to specific heat. This system undergoes a nanophase separation for n > 1 in alkyl side chain-rich domains and a backbone-rich matrix. Using inelastic neutron scattering, the low-frequency vibrational density of states (Boson peak, BP) of PnMAs with varying alkyl side chain lengths (methyl, butyl, hexyl, and octyl) is measured. The results reveal that the BP shifts to higher frequencies with increasing side chain length reaching a maximum. This result indicates a counterbalance of confinement effects and the scattering of the matrix. The behavior of the Boson peak of the PnMAs is compared to other nanophase-separated systems, such as Janus-polynorbornenes and hexakis(n-alkyloxy)triphenylene discotic liquid crystals. The study also explores the connection between the BP and specific heat capacity, showing a linear relationship between the maximum frequency of the BP and the maximum temperature of the specific heat capacity anomaly. Moreover, from the measured vibrational density of states, the specific heat capacity is calculated and compared to experimental results. The comparison reveals qualitative agreement between the calculated and experimental data. These findings provide evidence for the sound wave interpretation of the Boson peak. KW - Inelastic Neutron Scattering PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-636928 DO - https://doi.org/10.1021/acs.macromol.5c00898 SN - 1520-5835 SP - 1 EP - 12 PB - ACS Publications AN - OPUS4-63692 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kamdem Tamo, Arnaud A1 - Doench, Ingo A1 - Deffo, Gullit A1 - Jiokeng, Sherman Lesly Zambou A1 - Doungmo, Giscard A1 - Fotsop, Cyrille Ghislain A1 - Temgoua, Ranil Clement Tonleu A1 - Montembault, Alexandra A1 - Serghe, Anatoli A1 - Njanja, Evangeline A1 - Tonle, Ignas Kenfack A1 - Osorio-Madrazo, Anayancy T1 - Lignocellulosic biomass and its main structural polymers as sustainable materials for (bio)sensing applications N2 - (Bio)sensors are integral to various aspects of daily life, contributing to safety, monitoring, and awareness. In modern sensor devices, polymers play an important role, with increasing interest in bio-based materials. Biopolymers, unlike their synthetic counterparts, are abundant in nature and exhibit interesting functional properties that make them highly suitable as biomaterials for sensor technologies. Enhancing sensor performance to achieve a rapid response to stimuli is a key objective in sensor development. Lignocellulosic biomass (LCB) from plants holds promise in meeting such requirements due to its high surface area, tunable surface characteristics (including diverse pore sizes and morphologies), flexibility, printability, low density, and favorable physicochemical and thermal properties. Growing research in recent decades has focused on lignocellulosic composite materials due to their functional and environmentally friendly attributes. This review focuses on the valorization of lignocellulosic biomass and its three main biopolymer constituents (cellulose, hemicellulose, and lignin) for the development of electrochemical (bio)sensors. It also explores the macromolecular structure, sources, and inherent properties of LCB, with emphasis on the three main biopolymers and their applications in sensor technologies. Recent advances in the use of LCB and its structural biopolymers as materials for (bio)sensing applications are described and reviewed. The challenges associated with using these biomaterials in electroanalytical applications are also discussed, along with the exploration of their future potential for developing high-performance sensing technologies. KW - Chemical safety KW - Material safety KW - Quality ensurance PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-637230 DO - https://doi.org/10.1039/d5ta02900g SN - 2050-7496 SP - 1 EP - 69 PB - The Royal Society of Chemistry AN - OPUS4-63723 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Song, Jessica X. A1 - Scales, Brittan A1 - Nguyen, Minh A1 - Westberg, Emelie A1 - Witalis, Bartosz A1 - Urban-Malinga, Barbara A1 - Oberbeckmann, Sonja T1 - Close encounters on a micro scale: microplastic sorption of polycyclic aromatic hydrocarbons and their potential effects on associated biofilm communities N2 - Background: Within systems as dynamic as the aquatic environment, it is crucial to address the impacts of an ever-growing network of emerging pollutants at their intersection. With previous research having demonstrated the capacity of microplastics (MPs) to sorb persistent organic pollutants, we ask in our study how different plastic polymers that are found throughout aquatic systems interact with polycyclic aromatic hydrocarbons (PAHs) and how this intersection of pollutants might impact the bacterial communities that form on MP surfaces. We performed an in situ incubation experiment at different sites along the Baltic Sea coast and through a PAH and 16S amplicon analysis, we investigated the sorption patterns of different substrates and their potential impacts on associated biofilm communities. Results: PAH sorption patterns of polyethylene (PE), polystyrene (PS), and aquaria stone were found to be dictated predominantly by substrate type and secondly by incubation site. While PE showed a general positive trend of sorption, stone rather leached PAHs into the environment, whereas the PAH levels of PS remained relatively unchanged following incubation. These sorption patterns correlated significantly with the composition of biofilm communities observed on all three substrate types after a 6-week incubation period. Strong correlations between specific PAHs and bacterial taxa indicate a direct relationship between these factors. Elevated levels of specific 3- and 4-ring PAHs on PE and PS coincided with higher proportions of specific taxa reportedly capable of hydrocarbon utilisation as well as a reduced diversity among biofilm communities. Conclusion: The findings in our study highlight the importance of investigating contaminants such as MPs holistically, including any associated substances, to fully understand how they impact surrounding ecological systems as they traverse the different compartments of the aquatic ecosystem. KW - Aquatic biofilms KW - Plastic pollution KW - PAH KW - Microbiome KW - Emerging contaminants PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-636658 DO - https://doi.org/10.1186/s40793-025-00747-w SN - 2524-6372 VL - 20 IS - 84 SP - 1 EP - 15 PB - BMC Part of Springer Nature AN - OPUS4-63665 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wiehle, Philipp A1 - Baier, Johanna A1 - Thiele, Marc T1 - Structural Design of Earth Masonry in Accordance with Eurocode 6 – Considering Moisture Content and E/fk Ratio N2 - The load‐bearing behaviour of earth masonry is similar to conventional masonry, with two key differences: compressive strength and Young's modulus are dependent on moisture content, and the ratio between Young's modulus and characteristic compressive strength (E/fk) is significantly lower. The current design concept according to the Lehmbau Regeln does not explicitly address these factors, relying instead on a general safety margin, leading to an underestimation of the load‐bearing capacity of modern earth masonry.Compression tests on small‐scale masonry specimens and storey‐high walls revealed that compressive strength and Young's modulus decrease inversely proportional to the increase in relative humidity. Additionally, it was found that conventional masonry design guidelines overestimate the buckling resistance of earth masonry due to its low E/fk ratio of ∼440. However, this ratio remains independent of moisture content, simplifying structural design, as the load‐bearing capacity is only influenced by wall slenderness.The study's findings form the foundation for the newly published German design standard DIN 18940, which explicitly considers moisture content through service classes with moisture factors and addresses the low E/fk ratio with a bilinear adaptation of the reduction factor considering the slenderness. Along with the introduction of the semi‐probabilistic design concept and rigid‐plastic determination of cross‐sectional load‐bearing capacity, modern earth masonry can now be applied in buildings up to four storeys. T2 - Earth Builder Summit CY - Biberach, Germany DA - 06.03.2025 KW - Service class KW - Earth masonry KW - Structural design KW - Moisture PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-637803 DO - https://doi.org/10.1002/cepa.3287 SN - 2509-7075 VL - 8 IS - 1 SP - 9 EP - 21 PB - Ernst & Sohn GmbH AN - OPUS4-63780 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Dittmar, Stefan A1 - Weyrauch, Steffen A1 - Reemtsma, Thorsten A1 - Eisentraut, Paul A1 - Altmann, Korinna A1 - Ruhl, Aki S. A1 - Jekel, Martin T1 - Settling Velocities of Tire and Road Wear Particles: Analyzing Finely Graded Density Fractions of Samples from a Road Simulator and a Highway Tunnel N2 - The terminal settling velocity is considered the most critical parameter determining the transport of tire and road wear particles (TRWP) in aquatic environments. Nonetheless, no respective empirical data has been reported so far. In this study, particle samples from a road simulator and a highway tunnel were investigated with a validated imaging method. Different density and size fractions of both samples were measured separately, acquiring sizes and settling velocities of more than 30,000 individual particles. In addition, tire marker polymers were analyzed for each fraction via thermal extraction desorption-gas chromatography/mass spectrometry. Finally, the acquired particle data was combined according to the fractions’ estimated tire contents in order to deduce detailed probability distributions of particle size and settling velocity for the actual TRWP from both samples. Weighted by TRWP-incorporated tire mass, median diameters of 54 and 44 μm as well as median settling velocities of 0.65 and 0.22 mm/s were found for TRWP from the road simulator and highway tunnel, respectively. This study thus provides the first ever empirical data on TRWP settling velocities in water, which can be highly valuable input for modeling the environmental transport of TRWP and for dimensioning TRWP retention systems. KW - Microplastics KW - TED-GC/MS KW - Sinking velocities KW - Transport PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-635449 DO - https://doi.org/10.1021/acs.est.5c04165 SN - 0013-936X VL - 59 IS - 26 SP - 13434 EP - 13446 PB - American Chemical Society (ACS) AN - OPUS4-63544 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Auersch, Lutz T1 - Soil–structure interaction and damping by the soil - effects of foundation groups, foundation flexibility, soil stiffness and layers N2 - In many tasks of railway vibration, the structure, that is, the track, a bridge, and a nearby building and its floors, is coupled to the soil, and the soil–structure interaction and the damping by the soil should be included in the analysis to obtain realistic resonance frequencies and amplitudes. The stiffness and damping of a variety of foundations is calculated by an indirect boundary element method which uses fundamental solutions, is meshless, uses collocation points on the boundary, and solves the singularity by an appropriate averaging over a part of the surface. The boundary element method is coupled with the finite element method in the case of flexible foundations such as beams, plates, piles, and railway tracks. The results, the frequency-dependent stiffness and damping of single and groups of rigid foundations on homogeneous and layered soil and the amplitude and phase of the dynamic compliance of flexible foundations, show that the simple constant stiffness and damping values of a rigid footing on homogeneous soil are often misleading and do not represent well the reality. The damping may be higher in some special cases, but, in most cases, the damping is lower than expected fromthe simple theory. Some applications and measurements demonstrate the importance of the correct damping by the soil. KW - Soil–structure interaction KW - Soil dynamics KW - Radiation damping of the soil KW - Rigid foundation KW - Flexible foundation KW - Foundation groups KW - Boundary element method KW - Vibration measurement PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-627007 DO - https://doi.org/10.3390/vibration8010005 SN - 2571-631X VL - 8 IS - 5 SP - 1 EP - 28 PB - MDPI CY - Basel, Schweiz AN - OPUS4-62700 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Visileanu, Emilia A1 - Altmann, Korinna A1 - Stepa, Raluca A1 - Haiducu, Maria A1 - Miclea, Paul Tiberiu A1 - Vladu, Alina A1 - Dondea, Felicia A1 - Grosu, Marian Catalin A1 - Scarlat, Razvan T1 - Comparative Analysis of Airborne Particle Concentrations in Textile Industry Environments Throughout the Workday N2 - This paper addresses the growing concern surrounding microplastic pollution, particularly within the textile industry, and the associated potential health risks linked to the inhalation and ingestion of microplastic particles. Microplastics, defined as plastic particles smaller than five millimeters, are increasingly found not only in aquatic environments, but also in soils, air, and food. Although research on the health impacts of microplastics is still emerging, early studies indicate that these particles could contribute to health issues, including oxidative stress, inflammation, and cardiovascular diseases. Notably, individuals with higher concentrations of plastics in arterial plaques are more susceptible to heart attacks and strokes. In the textile industry, synthetic fibers such as polyester, nylon, and acrylic release microplastics into the air during production. The paper discusses a study conducted in a textile company that processes polyester yarns, where airborne microplastic concentrations were measured at various locations throughout the day. Particle sizes ranging from 0.3 nm to 10 nm were analyzed, revealing the presence of polyester polymers in the particulate matter. These findings underscore the widespread nature of microplastic pollution, particularly in industrial settings, and raise concerns about the health risks associated with prolonged exposure to airborne microplastics. While further research is necessary to fully understand the extent of these health impacts, preliminary data suggest a troubling link between microplastic inhalation and cardiovascular conditions. KW - Microplastics KW - Textiles KW - Airborne particles PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-635269 DO - https://doi.org/10.3390/microplastics4020034 SN - 2673-8929 VL - 4 IS - 2 SP - 1 EP - 17 PB - MDPI AG AN - OPUS4-63526 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gawek, Marcel A1 - Szymoniak, Paulina A1 - Hülagü, Deniz A1 - Hertwig, Andreas A1 - Schönhals, Andreas T1 - Molecular Mobility of Thin Films and the Adsorbed Layer of Poly(2-vinylpyridine) N2 - The molecular dynamics of thin films and the adsorbed layer of poly(2-vinylpyridine) (P2VP) were investigated using broadband dielectric spectroscopy (BDS) and spectroscopic ellipsometry. Thin films of P2VP were prepared on silicon substrates and characterized to understand the influence of film thickness on the thermal glass transition temperature (Tg) and molecular mobility. The ellipsometric study revealed a decrease in Tg with decreasing film thickness, attributed to the enhanced mobility at the polymer/air interface. The adsorbed layer, prepared via the solvent leaching approach, exhibited a higher Tg compared to the bulk, indicating reduced molecular mobility due to strong polymer substrate interactions. The dielectric measurements were carried out in two different electrode configurations, crossed electrode capacitors (CEC) and nanostructured electrodes (NSE), where the latter allows for a free surface layer at the polymer/air interface. The relaxation rates of the α-relaxation measured in the CEC geometry collapse into one chart independent from the film thickness. For the thin films measured in the NSE arrangement the relaxation rates slow down with decreasing film thickness which was discussed as related to a stronger interaction of the P2VP segments with the native SiO2 at the surface of the silicon substrate compared to aluminum. It is worth to note that the effect of the enhanced mobility at the polymer/air interface is not observed in the dielectric measurements. BDS measurements in NSE geometry identified an additional relaxation process (α*-relaxation) in thin films, which was more pronounced in the adsorbed layer. This process is hypothesized to be related to molecular fluctuations within the adsorbed layer including the adsorption/desorption dynamics of segments or to a Slow Arrhenius Process (SAP) related to the equilibration dynamics deep in the glassy state. KW - Thin polymer films PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-637181 DO - https://doi.org/10.1039/d5sm00539f SN - 1744-6848 SP - 1 EP - 12 PB - Royal Society of Chemistry (RSC) AN - OPUS4-63718 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Szymoniak, Paulina A1 - Kolmangadi, Mohamed A. A1 - Böhning, Martin A1 - De Souza, N. R. A1 - Juranyi, F. A1 - Zorn, R. A1 - Schönhals, Andreas T1 - Inelastic and Quasielastic Neutron Scattering on Polynorbornenes with Bulky Carbocyclic Side groups N2 - This study investigates the molecular mobility and vibrational properties of polynorbornenes with bulky carbocyclic side groups using inelastic and quasielastic neutron scattering techniques. The polymers, synthesized via metathesis and addition polymerization, exhibit varying degrees of microporosity, which ignificantly influences their gas separation performance. By inelastic neutron scattering experiments, it could be shown that all considered polymers have excess contributions to the low frequency vibrational density of states known as the Boson peak. The maximum frequency of the Boson peak correlates to the microporosity of the polymers. This correlation supports the sound wave interpretation of the Boson peak, suggesting that the microporous structure enhances the compressibility of the material at a microscopic length scale. The molecular mobility, particularly the methyl group rotation, was characterized using elastic scans and quasielastic neutron scattering. The study revealed a temperature dependent relaxation process, with the onset of molecular fluctuations observed around 200 K for the polymer containing methyl groups. For the polymer having no methyl groups only elastic scattering is observed. The methyl group rotation was analyzed in terms of a jump diffusion in a threefold potential with three equivalent energy minima. This leads to an almost correct description of the q dependence of the elastic incoherent scattering function when the number of hydrogen nuclei undergoing the methyl group rotation is considered. It was further evidenced that the fraction of methyl undergoing the methyl group rotation increases with increasing temperature. KW - Polymers of Intrinsic Microporosity KW - Neutron scattering PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-630297 DO - https://doi.org/10.1016/j.polymer.2025.128358 SN - 1873-2291 VL - 328 SP - 241 PB - Elsevier Ltd. AN - OPUS4-63029 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stühler, Merlin R. A1 - Makki, Hesam A1 - Silbernagl, Dorothee A1 - Dimde, Mathias A1 - Ludwig, Kai A1 - Tegner, Bengt E. A1 - Greve, Christopher A1 - Rausch, Konstantin A1 - Herzig, Eva M. A1 - Köhler, Anna A1 - Plajer, Alex J. T1 - Flexibility and Dynamicity Enhances and Controls Supramolecular Self-Assembly of Zinc(II) Metallogels N2 - Supramolecular self-assembly of stacked architectures is typically achieved through hydrogen bonding or π–π interactions between monomers constructed from stable and inert bonds. In contrast, coordinative interactions of early metals promise distinct self-assembly behaviour due to more flexible bonding geometries and a wider range of stabilities and exchange kinetics. In this report we demonstrate that tailoring the flexible coordination sphere of Zinc(II) complexes via subtle ligand modification promotes not only one but also three-dimensional self-assembly both thermodynamically and kinetically into higher-order fibrous morphologies, the latter being elucidated by electron tomography. As a result, coordination chemistry can be translated into both nanoscopic (fibre stiffness) and macroscopic (thermal gel stability) material properties. Utilizing dynamicity enables gelation via subcomponent self-assembly, constructing the supramolecular polymer network simultaneously with the monomer. Furthermore, coordinative dis- and reassembly via metal-ligand exchange reactions involving the first and second coordination spheres allows for control over gelation and emission of the system. Our report links concepts in supramolecular self-assembly and coordination chemistry by leveraging the unique bonding interactions that cannot be achieved for traditional monomers, promising applications in stimuli-responsive optoelectronics. KW - Nanomaterial KW - AFM KW - Organometallic KW - Gel PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-634221 DO - https://doi.org/10.1002/adfm.202507793 SN - 1616-301X SP - 1 EP - 10 PB - Wiley-VCH GmbH CY - Weinheim AN - OPUS4-63422 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Erxleben, Kjell A1 - Kaiser, Sebastian A1 - Rhode, Michael A1 - Kannengiesser, Thomas A1 - Kromm, Arne T1 - In-service and repair welding of pressurized hydrogen pipelines–a review on current challenges and strategies N2 - Hydrogen is the energy carrier for a sustainable future without fossil fuels. As this requires a reliable transportation infrastructure, the conversion of existing natural gas (NG) grids is an essential part of the worldwide individual national hydrogen strategies, in addition to newly erected pipelines. In view of the known effect of hydrogen embrittlement, the compatibility of the materials already in use (typically low-alloy steels in a wide range of strengths and thicknesses) must be investigated. Initial comprehensive studies on the hydrogen compatibility of pipeline materials indicate that these materials can be used to a certain extent. Nevertheless, the material compatibility for hydrogen service is currently of great importance. However, pipelines require frequent maintenance and repair work. In some cases, it is necessary to carry out welding work on pipelines while they are under pressure, e.g., the well-known tapping of NG grids. This in-service welding brings additional challenges for hydrogen operations in terms of additional hydrogen absorption during welding and material compatibility. The challenge can be roughly divided into two parts: (1) the possible austenitization of the inner piping material exposed to hydrogen, which can lead to additional hydrogen absorption, and (2) the welding itself causes an increased temperature range. Both lead to a significantly increased hydrogen solubility in the respective materials compared to room temperature. In that connection, the knowledge on hot tapping on hydrogen pipelines is rare so far due to the missing service experiences. Fundamental experimental investigations are required to investigate the possible transferability of the state-of-the-art concepts from NG to hydrogen pipeline grids. This is necessary to ensure that no critical material degradation occurs due to the potentially increased hydrogen uptake. For this reason, the paper introduces the state of the art in pipeline hot tapping, encompassing current research projects and their individual solution strategies for the problems that may arise for future hydrogen service. Methods of material testing, their limitations, and possible solutions will be presented and discussed. KW - In-service KW - Welding KW - Hydrogen pipeline KW - Review PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-638847 DO - https://doi.org/10.1007/s40194-025-02127-x SN - 0043-2288 SP - 1 EP - 24 PB - Springer Science and Business Media LLC AN - OPUS4-63884 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lozano, Daniel A1 - Gravenkamp, Hauke A1 - Birk, Carolin T1 - Simulations of ultrasonic guided wave scattering using the scaled boundary finite element method N2 - This paper presents a numerical framework employing the Scaled Boundary Finite Element Method (SBFEM) for efficiently solving ultrasonic guided wave modal scattering problems and constructing scattering matrices (S-matrices). The framework integrates hierarchical octree meshing and an enhanced far field formulation. It incorporates boundary integrals, enabling an accurate representation of defect interactions with guided waves. Validation is performed using a benchmark test supported by an error estimation method based on energy balance. Two practical examples are used to showcase the simulation framework, where the scattering of guided waves with surface-breaking and subsurface cracks near rivet holes is studied. KW - Guided waves KW - Scattering matrix KW - Scaled boundary finite element method KW - Elastodynamics PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-638295 DO - https://doi.org/10.1016/j.cma.2025.118204 SN - 0045-7825 VL - 445 SP - 1 EP - 23 PB - Elsevier B.V. AN - OPUS4-63829 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gerbeit, Marco A1 - Seeber, Henrik A1 - Grasse, Dennis A1 - Donner, Marcel A1 - Grobert, Steffen A1 - Krentel, Daniel T1 - Test set-up for reproducible shock wave generation N2 - A test setup was developed at the BAM test site to generate and record reproducible, adjustable shock waves resulting from gas detonations. The setup is used to study the impact of blasts on humans and structures with short setup times. To further develop this innovative test bench and improve reproducibility, the ignition source and gas composition is analysed in more detail. The experimental setup consists of a cylindrical pressure vessel (autoclave) that is operated with acetylene and oxygen at ambient pressure. The elevated pressure resulting from the combustion process is released through an orifice by the instantaneous rupture of a diaphragm. The shock propagates symmetrically into the free field, where it interacts with the models and sensors to be analysed. With this design, shock waves with a typical ideal Friedlander waveform characteristic, except for a reflection and a muzzle blast-like behavior that deviates from the ideal characteristics, can be generated. This setup enables an average peak overpressure of 88 kPa. By using exploding wires as an ignition source in comparison to a fusehead, the reproducibility was significantly increased during the test to σ=2.8 kPa from σ=9.5 kPa previously. The presented data confirms the quality and reliability of this setup in generating realistic, reproducible shocks. KW - Overpressure KW - Shock wave KW - Blast KW - Ignition source KW - Autoclave PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-637859 DO - https://doi.org/10.1016/j.jlp.2025.105736 SN - 0950-4230 VL - 98 SP - 1 EP - 6 PB - Elsevier Ltd. AN - OPUS4-63785 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schiaroli, Alice A1 - Mata, Christian A1 - Scarponi, Giordano Emrys A1 - Habib, Abdel Karim A1 - Kluge, Martin A1 - Ustolin, Federico A1 - Cozzani, Valerio T1 - Digital image processing for the advanced characterization and simulation of experimental fire tests N2 - The fire engulfment of storage tanks of hazardous materials is among the most critical scenarios in hazard assessment of industrial value chains. Laboratory and full-scale experimental trials are used to test the tank performance and integrity in such scenarios. However, strong uncertainties usually affect the actual fire load experienced by the tank, in particular when large-scale experiments are carried out in open test fields. Such uncertainties arise from several factors difficult to control during experimental tests, such as the atmospheric conditions as there is the influence of wind drifts influencing the actual fire engulfment, the flame temperature and the flame dynamic distribution around the target. Consequently, verifying the concordance of an experimental test with standard test criteria and defining accurate boundary conditions in correlated model simulations is challenging. In this study, the development of a novel method for the analysis of fire conditions based on image processing is presented. The approach allows identifying the flame coverage on the target surface during the test and provides an accurate map of the flame distribution on the equipment over time. The approach is tested using experimental data from a full-scale fire test campaign carried out on liquid hydrogen cryogenic tanks. The results prove to be accurate in replicating the experimental temperatures measured on the outer tank shell during the test. The proposed methodology can be used to better understand the results of experimental fire tests and to characterize realistic fire scenarios, also supporting the definition of fire test requirements. Moreover, the approach produces results that can be implemented as advanced space-time-varying boundary conditions in simulation models, improving their accuracy in reproducing real cases. KW - Fire test KW - Digital image processing KW - Flame coverage KW - Storage tank KW - Boundary conditions KW - Fire engulfment PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-636956 DO - https://doi.org/10.1016/j.psep.2025.107571 SN - 0957-5820 VL - 201 IS - B SP - 1 EP - 15 PB - Elsevier Ltd. AN - OPUS4-63695 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schilling, Markus A1 - Marschall, Niklas A1 - Niebergall, Ute A1 - Böhning, Martin T1 - Modernizing FNCT data handling in polymer labs: Towards efficient management N2 - A streamlined Python-based workflow for transforming Full-Notch Creep Test (FNCT) data into organized, machine-actionable formats is presented. The workflow automates the conversion of raw FNCT data from classic CSV and Excel files into structured outputs that facilitate future semantic integration. Emphasizing practical data handling, the approach includes automation scripts for efficient data extraction, transformation, and storage, which culminate in well-ordered files. This transformation paves the way for potential semantic data integration and facilitates access for users with varying levels of digital experience to enhanced data management in polymer research and testing. KW - PE-HD KW - Full-Notch Creep Test (FNCT) KW - Environmental Stress Cracking (ESC) KW - Data Interoperability KW - FAIR Data KW - Semantic Data PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-637826 DO - https://doi.org/10.1016/j.commatsci.2025.114085 SN - 0927-0256 VL - 259 SP - 1 EP - 5 PB - Elsevier B.V. AN - OPUS4-63782 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Liu, Yuanbin A1 - Morrow, Joe D. A1 - Ertural, Christina A1 - Fragapane, Natascia L. A1 - Gardner, John L. A. A1 - Naik, Aakash A. A1 - Zhou, Yuxing A1 - George, Janine A1 - Deringer, Volker L. T1 - An automated framework for exploring and learning potential-energy surfaces N2 - Machine learning has become ubiquitous in materials modelling and now routinely enables large-scale atomistic simulations with quantum-mechanical accuracy. However, developing machine-learned interatomic potentials requires high-quality training data, and the manual generation and curation of such data can be a major bottleneck. Here, we introduce an automated framework for the exploration and fitting of potential-energy surfaces, implemented in an openly available software package that we call (‘automatic potential-landscape explorer’). We discuss design choices, particularly the interoperability with existing software architectures, and the ability for the end user to easily use the computational workflows provided. We show wide-ranging capability demonstrations: for the titanium–oxygen system, SiO2, crystalline and liquid water, as well as phase-change memory materials. More generally, our study illustrates how automation can speed up atomistic machine learning in computational materials science. KW - Automation KW - Machine Learning KW - Machine learning potentials KW - Amorphous materials KW - High-throughput KW - Ab initio KW - Materials property prediction PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-639882 DO - https://doi.org/10.1038/s41467-025-62510-6 SN - 2041-1723 VL - 16 IS - 1 SP - 1 EP - 12 PB - Springer Science and Business Media LLC AN - OPUS4-63988 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Amariamir, Sasan A1 - George, Janine A1 - Benner, Philipp T1 - SynCoTrain: a dual classifier PU-learning framework for synthesizability prediction N2 - Material discovery is a cornerstone of modern science, driving advancements in diverse disciplines from biomedical technology to climate solutions. Predicting synthesizability, a critical factor in realizing novel materials, remains a complex challenge due to the limitations of traditional heuristics and thermodynamic proxies. While stability metrics such as formation energy offer partial insights, they fail to account for kinetic factors and technological constraints that influence synthesis outcomes. These challenges are further compounded by the scarcity of negative data, as failed synthesis attempts are often unpublished or context-specific. We present SynCoTrain, a semi-supervised machine learning model designed to predict the synthesizability of materials. SynCoTrain employs a co-training framework leveraging two complementary graph convolutional neural networks: SchNet and ALIGNN. By iteratively exchanging predictions between classifiers, SynCoTrain mitigates model bias and enhances generalizability. Our approach uses Positive and Unlabeled (PU) learning to address the absence of explicit negative data, iteratively refining predictions through collaborative learning. The model demonstrates robust performance, achieving high recall on internal and leave-out test sets. By focusing on oxide crystals, a well-characterized material family with extensive experimental data, we establish SynCoTrain as a reliable tool for predicting synthesizability while balancing dataset variability and computational efficiency. This work highlights the potential of co-training to advance high-throughput materials discovery and generative research, offering a scalable solution to the challenge of synthesizability prediction. KW - Synthesizability KW - Accelerated Materials Design KW - Materials Acceleration Platforms KW - Materials Design KW - Materials Discovery KW - Co-training PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-637907 DO - https://doi.org/10.1039/D4DD00394B SN - 2635-098X VL - 4 IS - 6 SP - 1437 EP - 1448 PB - Royal Society of Chemistry (RSC) AN - OPUS4-63790 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Liepold, Philipp A1 - Kromm, Arne A1 - Kannengießer, Thomas T1 - A Force Based Determination of Hot Cracking Susceptibility N2 - Two high-strength, low-alloy Gas Metal Arc Welding (GMAW) wires were evaluated for their susceptibility to Solidification Cracking (SC) using a modified version of the Transverse Motion Weldability (TMW) test. In theoriginal TMW test, the Transverse Displacement Speed (TDS) is varied iteratively, and crack lengths are measured in each iteration. The modified version eliminates the need for multiple runs by continuously reducing the TDS over a single run. Rather than emphasizing crack lengths, this method assesses the reaction force to the TDS, thereby determining a Critical TDS (CTDS). This critical point directly correlates with the cessation of SC growth. CTDS values were measured under a range of welding parameters, thereby demonstrating the influence of Welding speed and arc energy (U × I/welding speed) on SC susceptibility for the tested filler metals. The CTDS data obtained from this testing method have the potential to provide valuable insights for practical applications in the field. KW - Force based KW - Neural Network KW - TRS PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-640140 DO - https://doi.org/10.5781/JWJ.2025.43.4.10 SN - 2466-2100 VL - 43 IS - 4 SP - 447 EP - 457 AN - OPUS4-64014 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Nicolicea, Alberto A1 - Oliveros-Mata, E. S. A1 - Makarov, D. A1 - Melzer, Michael A1 - Pelkner, Matthias T1 - Flexible anisotropic magnetoresistive sensors for novel eddy current testing applications N2 - The standard method for eddy current testing (ET) of conductive materials relies on using rigid coils. In recent years magnetoresistive (MR) sensors in combination with an excitation wire have become a promising candidate for this application since it would increase the spatial resolution. New developments in flexible electronics have enabled the production of flexible sensors with the novel capability of scanning samples in conformal contact with the surface. In this article flexible anisotropic magnetoresistive (AMR) sensors were used in combination with a thin induction wire to perform eddy current testing of a curved aluminum sample with several defects imprinted on its surface. To benchmark the performance of this new method, a flat sample with reference defects of various dimensions was also scanned using flexible AMR sensors, inductive coils and rigid giant magnetoresistive (GMR) sensors. The results show that this new method of using flexible magnetic field sensors coupled with an excitation wire can easily be applied to the scanning of curved samples, while in the benchmark test employing the flat sample, the performance is not far behind more conventional techniques, with defects with depths down to 30 μm and widths down to 400 μm being detectable with an SNR of 3 (signal magnitude) and 8 (signal phase shift) at the excitation frequency of 50 kHz, and defects with depths down to 30 μm and widths down to 600 μm being detectable with an SNR of 10 (signal magnitude) and 17 (signal phase shift) at 260 kHz. KW - Magnetic field sensors KW - Flexible magnetic field sensors KW - Flexible electronics KW - Non-destructive testing KW - Eddy current testing KW - Thin film sensor fabrication KW - Defect detection KW - Magnetism PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-634325 DO - https://doi.org/10.1016/j.measurement.2025.117340 SN - 1873-412X VL - 253, Part A SP - 1 EP - 15 PB - Elsevier CY - Amsterdam AN - OPUS4-63432 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bruno, Francesco A1 - Fiorucci, Letizia A1 - Vignoli, Alessia A1 - Meyer, Klas A1 - Maiwald, Michael A1 - Ravera, Enrico T1 - pyIHM: Indirect Hard Modeling, in Python N2 - NMR is a powerful analytical technique that combines an exquisite qualitative power, related to the unicity of the spectra of each molecule in a mixture, with an intrinsic quantitativeness, related to the fact that the integral of each peak only depends on the number of nuclei (i.e., the amount of substance times the number of equivalent nuclei in the signal), regardless of the molecule. Signal integration is the most common approach in quantitative NMR but has several drawbacks (vide infra). An alternative is to use hard modeling of the peaks. In this paper, we present pyIHM, a Python package for the quantification of the components of NMR spectra through indirect hard modeling, and we discuss some numerical details of the implementation that make this approach robust and reliable. KW - Algorithms KW - Chemical Structure KW - Deconvolution KW - Mixtures KW - NMR spectroscopy PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-626793 DO - https://doi.org/10.1021/acs.analchem.4c06484 SN - 1520-6882 VL - 97 IS - 8 SP - 4598 EP - 4605 PB - ACS Publications CY - Washington D.C. AN - OPUS4-62679 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Yang, Fan A1 - Meng, Xiangmeng A1 - Putra, Stephen Nugraha A1 - Bachmann, Marcel A1 - Rethmeier, Michael T1 - Numerical studies of process porosity suppression by magnetohydrodynamic technology during the laser beam welding of aluminum alloy N2 - Magnetohydrodynamic (MHD) technology is acknowledged as a promising method for mitigating the porosity defects in laser-welded joints of aluminum alloys. A transient 3D multi-physical numerical model of laser beam welding (LBW), coupled with the MHD and oscillating metal vapor plume model, is developed to study the suppression mechanisms of process porosity by an external magnetic field. The experimental results demonstrate that the porosity ratio is reduced by 93.5 % as the oscillating magnetic field is applied. This significant reduction confirms the effectiveness of the MHD technology in suppressing porosity defects. A downward time-averaged Lorentz force is induced in the weld pool, which affects the fluid flow pattern and the weld pool profile. The change of the flowing pattern in the weld pool by the magnetic field does not always have a positive effect on the porosity suppression. In addition, an analytical model shows that the bubble escape window is expanded by 62 % under the effect of the oscillating magnetic field. The additional upward velocity provided by the electromagnetic expulsive force on the bubbles and the change of weld pool profile are considered favorable factors in eliminating the porosity defects. The numerical and analytical model developed for analyzing the bubble escape window have been validated by experimental results. KW - Laser beam welding KW - Aluminum alloy KW - Process porosity defects KW - Magnetohydrodynamic technology KW - Bubble escape KW - Numerical simulation PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-637642 DO - https://doi.org/10.1016/j.ijheatmasstransfer.2025.127525 SN - 0017-9310 VL - 253 SP - 1 EP - 13 PB - Elsevier Ltd. AN - OPUS4-63764 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Yang, Keke A1 - Wang, Zhuoqun A1 - Haak, Viktor A1 - Olfert, Viktoria A1 - El-Sari, Bassel A1 - Hein, David A1 - Biegler, Max A1 - Rethmeier, Michael A1 - Meschut, Gerson T1 - A novel welding schedule for expanding the expulsion-free process window in resistance spot welding of dissimilar joints with ultra-high strength steel N2 - This study introduces a novel approach to expanding the maximum expulsion-free process window in resistance spot welding (RSW) of dissimilar joints between ultra-high strength steel (UHSS) and mild steel. Quantitative analysis revealed that expulsion is driven by the interaction between nugget growth rate and plastic shell thickness. Based on this finding, the welding schedule was optimized by applying a preheating current to form an initial plastic shell, followed by a ramp-up current profile during the main welding phase. Welding simulations indicated that the ramp-up current slowed nugget growth, improved plastic shell formation, and prevented nugget breakthrough, thereby reducing the risk of expulsion. Experimental validation showed a 19 % increase in maximum expulsion-free heat input, with the nugget diameter increasing by 7.6 % to 8.94 mm compared to the reference welding schedule. Furthermore, even when expulsion occurred beyond the process window, this optimization delayed its occurrence, minimizing its impact on spot weld quality. Finally, the optimized welding schedule also exhibited significant robustness. Despite a 2 mm initial gap disturbance, the maximum expulsionfree heat input increased by 57 %, while the nugget diameter grew by 30 % to 8.92 mm. These results confirm that the proposed approach effectively extends the process window by preventing expulsion and enhances process stability. KW - Expulsion KW - Resistance spot welding KW - Finite element modelling KW - Preheating KW - Ultra-high-strength steel PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-626877 DO - https://doi.org/10.1016/j.jmapro.2025.02.009 SN - 2212-4616 VL - 137 SP - 306 EP - 309 PB - Elsevier BV AN - OPUS4-62687 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Feiler, Torvid A1 - Emmerling, Franziska A1 - Bhattacharya, Biswajit T1 - Sustainable mechanochemical approach for the selective synthesis of multicomponent organic solids: real-time in situ insights N2 - Crystalline multicomponent organic solids (MOSs) such as cocrystals and ionic cocrystals hold immense potential in diverse functional applications, ranging from pharmaceuticals to optoelectronics. However, conventional solution-based crystallization methods often result in polymorphic mixtures and lack precise control over product composition. Herein, we report a comparative investigation of solution crystallization versus mechanochemical synthesis for constructing MOSs from 9-anthracenecarboxylic acid (ACA) and 4,4 '-bipyridine (BPY). Solution-based approaches consistently yielded concomitant formation of neutral cocrystal (CC) and ionic cocrystal (ICC) forms, regardless of the solvent used. The resulting multicomponent solids were comprehensively characterized using a combination of single crystal X-ray diffraction, powder X-ray diffraction, Fourier-transform infrared spectroscopy, differential thermal analysis, and thermogravimetric analysis. In contrast, mechanochemical methods, including neat grinding (without solvent) and liquid-assisted grinding (with minimum solvent), enabled selective formation of either a phase pure CC or ICC form. Less polar and nonpolar organic solvents favor the kinetic CC, while polar water promotes formation of the thermodynamically stable ICC. Time-resolved in situ powder X-ray diffraction (TRIS-PXRD) captures the dynamic evolution of solid-state phases and reveals the complete transformation of the CC into ICC under neat grinding or water-assisted conditions. This study highlights the powerful role of mechanochemistry and in situ monitoring in steering solid-state reactivity and offers a sustainable pathway for the targeted and scalable synthesis of pure multicomponent organic materials. KW - Cocrystal KW - Synchrotron X-ray powder diffraction KW - Time-resolved in situ investigation PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-641409 DO - https://doi.org/10.1039/D5CE00663E SN - 1466-8033 SP - 1 EP - 9 PB - Royal Society of Chemistry (RSC) CY - Cambridge AN - OPUS4-64140 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Paskin, Alice A1 - Couasnon, Thaïs A1 - Blukis, Roberts A1 - Perez, Jeffrey Paulo H. A1 - Reinsch, Stefan A1 - Roddatis, Vladimir A1 - Syczewski, Marcin A1 - Benning, Liane G. T1 - Temperature-Induced Phase Transitions of Vivianite: In Situ Analysis of a Redox-Driven Crystallization N2 - We document a solid-state, temperature-dependent (25−700 °C), multistage redox transformation of crystalline ferrous iron phosphate, vivianite (Fe3(PO4)2·8H2O). Under anoxic conditions, vivianite breaks down at T > 250 °C into an anhydrous, amorphous intermediate Fe3(PO4)2 phase, yet the bulk shape and morphology of the starting vivianite crystals were retained. This amorphous intermediate phase remained stable until T > 500 °C, after which a redox-dependent crystallization into two different minerals was observed. Under anoxic conditions, the amorphous ferrous intermediate (Fe3(PO4)2) transformed into the crystalline ferrous phosphate (graftonite, (Fe2+)3(PO4)2), while under oxic conditions it crystallized into a ferric phosphate (rodolicoite, Fe3+PO4). Graftonite formation occurs via an exothermic molar enthalpy (ΔHcryst) of −16.7 ± 0.2 kJ mol−1. Rietveld refinements of the two crystalline endmembers (vivianite and graftonite) revealed a unit cell volume decrease of ∼3.1% during the transformation, which was observed by in situ electron microscopic observations as an overall shrinking of the initial vivianite crystals. Despite volume loss and bubble-like features, the original vivianite shape was preserved, indicating a solid-state pseudomorphic transformation. Ex situ XRD and TEM-EELS analyses confirmed the ferrous-to-ferric oxidation, forming rodolicoite, through changes in the Fe geometry and oxidation state. KW - Vivianite KW - Graftonite KW - Crystallization enthalpy KW - Ferrous phosphates PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-640782 DO - https://doi.org/10.1021/acs.inorgchem.5c02399 SN - 0020-1669 VL - 46 IS - 36 SP - 18227 EP - 18236 PB - American Chemical Society (ACS) AN - OPUS4-64078 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Yalçınyüz, Aybike A1 - Raute, Julius A1 - Gonzalez-Gutierrez, Joamin A1 - Pei, Eujin A1 - Biegler, Max A1 - Rethmeier, Michael T1 - Electron Beam Bonding: A novel method for joining additively manufactured carbon fiber thermoplastic composites with aluminum to produce multi-material joints for lightweight applications N2 - In recent years, new solutions have been explored to reduce the weight of components for the automotive, railway, and aerospace industries. For this reason, Carbon Fiber Composites (CFCs) have increasingly replaced metals in products that need to be lightweight. However, due to their poor thermal conductivity, CFCs have limited use in applications requiring efficient heat dissipation. In such applications, conventionally manufactured metal alloys are typically utilized. To address these limitations, a novel approach using a combination of additively manufactured aluminum and CFCs is proposed to exploit the distinct advantages of both materials. These innovative hybrid structures aim to combine good structural and thermal management properties with reduced weight compared to conventionally produced metal products. In this study, additively manufactured aluminum alloy (AlSi10Mg) and short carbon fiber Polyamide 6 composite (sCF-PA6) are utilized to produce metal–polymer pairs using electron beam energy to bond the two materials. Direct irradiation of short CFCs with electron beam leads to polymer degradation. Thus, a novel method “Electron Beam Bonding” for joining CFCs with aluminum alloy in various joint configurations using electron beam technology is demonstrated. This innovative approach presents a promising solution for creating metal–polymer multi-materials for lightweight applications. KW - Electron beam bonding KW - Multi-material KW - Lightweight KW - Additive manufactured materials KW - Short carbon fiber composites KW - AlSi10Mg KW - Joining PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-641705 DO - https://doi.org/10.1007/s40964-025-01206-1 SN - 2363-9512 SP - 1 EP - 7 PB - Springer International Publishing CY - Cham AN - OPUS4-64170 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Holt, Erika A1 - Oksa, Maria A1 - Banford, Anthony A1 - Carbol, Paul A1 - Abdelouas, Abdesselam A1 - Giboire, Isabelle A1 - Mennecart, Thierry A1 - Niederleithinger, Ernst T1 - Predisposal Radioactive Waste Management (PREDIS) Project Final Achievements and Impacts Overview N2 - The PREDIS project on Predisposal of Radioactive Waste has succeeded in developing and implementing new methods, processes and technologies for treatment of challenging low-level waste (LLW) and intermediate level waste (ILW) streams. Over the 4-year duration, this Euratom project of 47 partners from 17 Member States has worked in close collaboration with 25 End User industrial members to advance the technologies associated with predisposal issues. This has included characterisation followed by treatment, conditioning and processing of metallics, liquid organic and solid organic wastes as well as with digitalization technologies for assessing performance of concrete waste packages and pre-disposal storage. Long-term modelling and performance testing have been done to verify the safety and effectiveness of the new or enhanced solutions. Value Assessments were done for some of the new solutions to ensure implementors would have sufficient tools for making choices about the potential implementation. This included life-cycle assessment of quantitative sustainability indicators and life cycle-costing for economic indicators. This project addressed new guidance on Waste Acceptance Criteria and contributed with a revised Strategic Research Agenda to guide future predisposal activities, complimentary to the holistic waste management programme. Knowledge Management actions were also an integral part of the whole project to foster competence development and capturing knowledge. Actions included training, mobility, and guidance especially through online forums such as webinars and digital training. This paper provides a snapshot of some of the key outcomes and impacts from the project, from technical as well as strategic and knowledge perspectives. KW - Nuclear waste KW - Pre-disposal KW - Intermediate storage KW - Treatment KW - Monitoring PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-638480 DO - https://doi.org/10.1051/epjn/2025028 SN - 2491-9292 VL - 11 SP - 1 EP - 7 PB - EDP Sciences AN - OPUS4-63848 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Meng, Xiangmeng A1 - Bachmann, Marcel A1 - Yang, Fan A1 - Rethmeier, Michael T1 - Toward prediction and insight of porosity formation in laser welding: A physics-informed deep learning framework N2 - The laser welding process is an important manufacturing technology for metallic materials. However, its application is often hindered by the occurrence of porosity defects. By far, an accurate prediction of the porosity defects and an insight into its formation mechanism are still challenging due to the highly nonlinear physics involved. In this paper, we propose a physics-informed deep learning (PIDL) framework by utilizing mechanistic modeling and experimental data to predict the porosity level during laser beam welding of aluminum alloys. With a proper selection of the physical variables (features) concerning the solidification, liquid metal flow, keyhole stability, and weld pool geometry, the PIDL model shows great superiority in predicting the porosity ratio, with a reduction of mean square error by 41 %, in comparison with the conventional DL model trained with welding parameters. Furthermore, the selected variables are fused into dimensionless features with explicit physical meanings to improve the interpretability and extendibility of the PIDL model. Based on a well-trained PIDL model, the hierarchical importance of the physical variables/procedures on the porosity formation is for the first time revealed with the help of the Shapley Additive Explanations analysis. The keyhole ratio is identified as the most influential factor in the porosity formation, followed by the downward flow-driven drag force, which offers a valuable guideline for process optimization and porosity minimization. KW - Laser beam welding KW - Physics-informed deep learning KW - Porosity prediction KW - Feature fusion KW - Hierarchical importance PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-624708 DO - https://doi.org/10.1016/j.actamat.2025.120740 VL - 286 SP - 1 EP - 13 PB - Elsevier B.V. AN - OPUS4-62470 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Akyel, Fatma A1 - Üstündag, Ömer A1 - Bakir, Nasim A1 - Brunner-Schwer, Christian A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael T1 - Influence of heat input on cooling rates and mechanical properties of laser hybrid welded thick structural steels N2 - Laser hybrid welding presents several challenges when used to weld thick steels. A typical weld is divided into the arcdominated and laser-dominated zone. These zones lead to variations in the mechanical properties of the weld. The laserdominated zone is of particular importance regarding mechanical properties, notably Charpy impact toughness, due to the high cooling rates and the absence of filler wire. The low heat input of the laser can lead to martensitic microstructure causing hardening and deterioration of impact toughness. The high heat input of the arc can lead to grain coarsening and even loss of impact toughness. This study examines the influence of heat input on the cooling rates, microstructure and mechanical properties of single-pass laser hybrid welded steels of S355J2 and EH36 with thicknesses up to 30 mm. The experiments were performed with a 20-kW fibre laser and a contactless electromagnetic weld backing in the butt-joint configuration in 1G welding position. The cooling time was measured in three different locations near the fusion lines corresponding to different heights of the seam using a special configuration with pyrometers, collimators and optical fibres. The test specimens for the Charpy impact testing and tensile testing were extracted in three different depths. The experiments indicated that a heat input of 1.6 kJ/mm–2 kJ/mm, 2 kJ/mm–2.4 kJ/mm and 3.7 kJ/mm were recommended when single-pass laser hybrid welding of 20-, 25-, and 30-mm-thick structural steels regarding the minimum requirements of the mechanical properties, respectively. KW - Laser hybrid welding KW - Heat input KW - Mechanical properties KW - Charpy impact toughness KW - Cooling rate PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-625282 DO - https://doi.org/10.1007/s40194-025-01924-8 SN - 1878-6669 SP - 1 EP - 15 PB - Springer CY - United Kingdom AN - OPUS4-62528 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kemmler, Samuel A1 - Rettinger, Christoph A1 - Rüde, Ulrich A1 - Cuéllar, Pablo A1 - Köstler, Harald T1 - Efficiency and scalability of fully-resolved fluid-particle simulations on heterogeneous CPU-GPU architectures N2 - Current supercomputers often have a heterogeneous architecture using both conventional Central Processing Units (CPUs) and Graphics Processing Units (GPUs). At the same time, numerical simulation tasks frequently involve multiphysics scenarios whose components run on different hardware due to multiple reasons, e.g., architectural requirements, pragmatism, etc. This leads naturally to a software design where different simulation modules are mapped to different subsystems of the heterogeneous architecture. We present a detailed performance analysis for such a hybrid four-way coupled simulation of a fully resolved particle-laden flow. The Eulerian representation of the flow utilizes GPUs, while the Lagrangian model for the particles runs on conventional CPUs. Two characteristic model situations involving dense and dilute particle systems are used as benchmark scenarios. First, a roofline model is employed to predict the node level performance and to show that the lattice-Boltzmann-based Eulerian fluid simulation reaches very good performance on a single GPU. Furthermore, the GPU-GPU communication for a large-scale Eulerian flow simulation results in only moderate slowdowns. This is due to the efficiency of the CUDA-aware MPI communication, combined with the use of communication hiding techniques. On 1024 A100 GPUs, an overall parallel efficiency of up to 71% is achieved. While the flow simulation has good performance characteristics, the integration of the stiff Lagrangian particle system requires frequent CPU-CPU communications that can become a bottleneck, especially when simulating the dense particle system. Additionally, special attention is paid to the CPU-GPU communication overhead since this is essential for coupling the particles to the flow simulation. However, thanks to our problem-aware co-partitioning, the CPU-GPU communication overhead is found to be negligible. As a lesson learned from this development, four criteria are postulated that a hybrid implementation must meet for the efficient use of heterogeneous supercomputers. KW - Discrete element method KW - Hybrid implementation KW - High-performance computing KW - Particulate flow KW - Lattice Boltzmann method PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-623958 DO - https://doi.org/10.1177/10943420241313385 SN - 1741-2846 SP - 1 EP - 19 PB - SAGE Publications AN - OPUS4-62395 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zinas, Orestis A1 - Papaioannou, Iason A1 - Schneider, Ronald A1 - Cuéllar, Pablo T1 - Multivariate Gaussian Process Regression for 3D site characterization from CPT and categorical borehole data N2 - Accurate prediction of subsurface stratigraphy and geotechnical properties, along with quantification of associated uncertainties, is essential for improving the design and assessment of geotechnical structures. Several studies have utilized indirect data from Cone Penetration Tests (CPTs) and employed statistical and Machine Learning methods to quantify the geological and geotechnical uncertainty. Incorporating direct borehole data can reduce uncertainties. This study proposes a computationally efficient multivariate Gaussian Process model that utilizes site-specific data and: (i) jointly models multiple categorical (USCS labels) and continuous CPT variables, (ii) learns a non-separable covariance structure leveraging the Linear Model of Coregionalization, and (iii) predicts a USCS based stratigraphy and CPT parameters at any location within the 3D domain. The results demonstrate that integrating geotechnical and geological data into a unified model yields more reliable predictions of subsurface stratification, enabling the parallel interpretation of both USCS classification and CPT profiles. Importantly, the model demonstrates its potential to integrate multiple variables from different sources and data types, contributing to the advancement of methodologies for the joint modeling of geotechnical, geological, and geophysical data. KW - Geotechnical site-characterization KW - Cone Penetration Tests KW - Stratigraphy prediction KW - Multivariate Gaussian process KW - Variational inference KW - Linear Model of Coregionalization PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-629456 DO - https://doi.org/10.1016/j.enggeo.2025.108052 SN - 1872-6917 VL - 352 SP - 1 EP - 19 PB - Elsevier B.V. AN - OPUS4-62945 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bernardy, Christopher A1 - Habib, Abdel Karim A1 - Kluge, Martin A1 - Schalau, Bernd A1 - Kant, Hanjo A1 - Schulze, Marcel A1 - Orchini, Alessandro T1 - Large-scale investigations of the thermal radiation of hydrogen jet flames N2 - For industrial applications dealing with hydrogen, the definition of safety distances and the assessment of possible hazards emanating from releases is mandatory. Since hydrogen is usually stored and transported under pressure, one scenario to be considered is the momentum driven release of hydrogen from a leakage with subsequent ignition. In this scenario, the emitted heat radiation from the resulting jet flame to the surroundings has to be determined to define adequate safety distances. For hydrocarbon flames, different jet flame models are available to assess the hazards resulting from an ignited jet release. Since hydrogen flames differ from hydrocarbon flames in their combustion behavior, it has to be checked if these models are also applicable for hydrogen. To evaluate the accuracy of these models for hydrogen jet flames, tests with a horizontal outlet at large-scale are carried out at the BAM Test Site for Technical Safety (BAM-TTS). Herein, the flame geometry and the heat radiation at defined locations in the surroundings are recorded for varying release parameters such as release pressure (currently up to max. 250 bar), mass flow (up to max. 0.175 kg/s) at an outlet diameter of 30 mm (with an upstream nozzle of 7.7 mm). The challenge here is the characterization of the flame geometry in an open environment and its impact on the thermal radiation. Existing heat radiation data from the literature are mostly based on unsteady outflow conditions. For a better comparability with the steady state jet flame models, the experiments presented here are focused on ensuring a constant mass flow over the release duration (currently 120 s) to obtain a stationary jet flame. In addition, stationary outflow tests with hydrocarbons (methane) were also carried out, which are intended to serve as reference tests for checking flame models based on hydrocarbon data. The comparison of the flame geometry shows that hydrogen jet flames with the same outlet mass flow have a greater flame length (average deviation of 15 %) but a smaller flame diameter than methane jet flames (average deviation of 17 %). Conclusions regarding thermal radiation show that the proportion of total combustion energy emitted as thermal radiation is lower for hydrogen (x_rad= 0.04–0.09) than for methane (x_rad = 0.06–0.1). A comparison of the surface emissive power (SEP) of the jet flame shows a SEP range of 7 kW/m2-15 kW/m2 for hydrogen and 3 kW/m2 - 9,5 kW/m2 for methane. KW - Hydrogen KW - Release KW - Thermal radiation KW - Jet flame KW - Radiant heat fraction PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-622891 DO - https://doi.org/10.1016/j.jlp.2024.105491 SN - 1873-3352 VL - 94 SP - 1 EP - 6 PB - Elsevier B.V. AN - OPUS4-62289 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Dorgerloh, Ute A1 - Becker, Roland A1 - Freeling, Finnian A1 - Scheurer, Marco A1 - Gökçe, Emine A1 - Strack, Katrin A1 - Sommerfeld, Thomas A1 - Sauer, Andreas A1 - Schneider, Jonas A1 - Härtel, Christoph A1 - Valkov, Vassil A1 - Moser, Lukas A1 - Geiß, Sabine A1 - Junginger, Sabine A1 - Schlittenbauer, Linda A1 - Suess, Elke A1 - Ruth, Katinka T1 - Standardising the quantification of trifluoroacetic acid in water: Interlaboratory validation trial using liquid chromatography-mass spectrometric detection (LC–MS/MS) N2 - The concentration of trifluoroacetic acid in surface and groundwaters and drinking water is subject of increasing concern. Since there is no standardised procedure available, German standardisation body DIN has initiated the first draft standard using liquid chromatography with tandem mass spectrometry (LC–MS/MS) after direct injection for the concentration range between ≥ 0.1 and 3 µg/L. Herein, the interlaboratory comparison as final validation step involving 12 expert laboratories from Germany and Switzerland is described. Two groundwaters, two surface waters, a drinking water, a rainwater, and two fortified groundwater samples displayed relative repeatability standard deviations between 3 and 7% and relative reproducibility standard deviation between 6 and 20% and were included in the draft standard DIN 38407-53. KW - TFA Trifluoroacetic acid KW - LC/MS-MS KW - Validation trial PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-632376 DO - https://doi.org/10.1007/s00769-025-01640-2 SN - 0949-1775 SP - 1 EP - 4 PB - Springer CY - Berlin AN - OPUS4-63237 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Heyn, A. A1 - Kotula, Stefan A1 - Ebell, Gino A1 - Babutzka, M. T1 - Results of a Round Robin Test for the Determination of Polarization Resistances on Differently Weathered Zinc Samples Using Gel Electrolytes N2 - This article presents the results of a round robin test throughout Germany with 19 participating institutions. Corrosion productlayer resistances (RL ) were determined on two differently weathered pure zinc samples and a sample activated with NaOH bymeans of electrochemical measurement of the linear polarization resistance (LPR) using agar‐based gel electrolytes. The roundrobin test was organized by the Bundesanstalt für Materialforschung und ‐prüfung (BAM) in Berlin. The measurements werecarried out by the participants in the period from May to July 2021. The results are summarized in this article comprising anassessment of the reproducibility and repeatability of the measurements. The methodology is suitable for distinguishing zincsurfaces after exposure to different atmospheres based on the corrosion product layer resistances (RL). In addition, possibleproblems in the application of the method were identified, and solutions for improving reproducibility and repeatability arediscussed. The results and knowledge from the round robin test are incorporated into a new test standard (DIN 50023:2024‐07)for this measurement method KW - Corrosion PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-630546 DO - https://doi.org/10.1002/maco.202414696 SN - 1521-4176 SP - 1 EP - 12 PB - Wiley AN - OPUS4-63054 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Qi, Naiyu A1 - Somaskandan, Rachana A1 - Graeber, Gustav T1 - High-Precision Surface Tension Measurements of Sodium, Potassium, and Their Alloys via Du Noüy Ring Tensiometry N2 - The development of post-lithium-ion batteries has sparked significant interest in alkali-metal anodes, particularly sodium (Na), potassium (K), and sodium−potassium (Na−K) alloys. Na−K alloys are promising for partially liquid anodes due to their unique low melting points. A critical factor influencing Na−K-based anode performance is wetting behavior, which governs electrical conductivity, mechanical contact, and long-term stability. At the heart of wetting lies surface tension, a fundamental property of solid−liquid− gas interactions. However, the surface tension of alkali metals and their alloys, particularly Na−K systems, remains poorly understood due to experimental and theoretical challenges. This study bridged these gaps by employing Du Noüy ring tensiometry for the first time in alkali-metal systems to measure the surface tension of Na, K, and Na−K alloys across temperatures from ambient to 180 °C. A key innovation in this work is the development of the push-in Du Noüy method, which provided significantly higher precision and reliability compared to the traditional pull-out technique, without requiring a correction factor. The measured surface tension decreased with increasing temperature for the studied Na−K alloys. For instance, for a eutectic Na−K mixture, the surface tension decreases from 121.7 mN m−1 to 112.2 mN m−1 when increasing the temperature from ambient to 180 °C. Additionally, this study presented the first use of Gibbs free energy minimization to model the surface tension of the Na−K system. The robust method significantly enhanced the predictive accuracy compared to the previous simplified model, reducing deviations from 25% to 2%. Our findings reveal that surface tension increases with sodium mole fraction in the bulk phase, yet the surface monolayer remains potassium-rich, indicating non-ideal surface behavior. This study deepens the understanding of alkali-metal wetting behavior, providing valuable insights for designing optimized interfaces in next-generation semi-solid alkali-metal batteries. KW - Sodium−potassium alloy KW - Liquid-metal anodes KW - Alkali metal KW - Batteries KW - Surface tension PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-630102 DO - https://doi.org/10.1021/acsami.5c02183 SN - 1944-8252 VL - 17 IS - 17 SP - 25985 EP - 25995 PB - American Chemical Society (ACS) CY - Washington, DC AN - OPUS4-63010 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Simon, Patrick A1 - Schneider, Ronald A1 - Baeßler, Matthias A1 - Morgenthal, Guido T1 - Parallelized adaptive Bayesian updating with structural reliability methods for inference of large engineering models N2 - The reassessment of engineering structures, such as bridges, now increasingly involve the integration of models with realworld data. This integration aims to achieve accurate ‘as-is’ analysis within a digital twin framework. Bayesian model updating combines prior knowledge and data with models to enhance the modelling accuracy while consistently handling uncertainties. When updating large engineering models, numerical methods for Bayesian analysis present significant computational challenges due to the need for a substantial number of likelihood evaluations. The novelty of this contribution is to parallelize adaptive Bayesian Updating with Structural reliability methods combined with subset simulation (aBUS) to improve its computational efficiency. To demonstrate the efficiency and practical applicability of the proposed approach, we present a case study on the Maintalbrücke Gemünden, a large railway bridge. We leverage modal property data to update a linear-elastic dynamic structural model of the bridge. The parallelized aBUS approach significantly reduces computational time, making Bayesian updating of large engineering models feasible within reasonable timeframes. The improved efficiency allows for a wider implementation of Bayesian model updating in structural health monitoring and maintenance decision support systems. KW - Bayesian model updating KW - Bayesian updating with structural reliability methods KW - Structural health monitoring KW - Parallelization KW - Modal analysis KW - Railway bridge PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-633686 DO - https://doi.org/10.1177/13694332251346848 SN - 1369-4332 SN - 2048-4011 SP - 1 EP - 26 PB - Sage AN - OPUS4-63368 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Willeke, Maraike A1 - Giese, Marcel A1 - Lorenz, Swenja A1 - Treutler, Kai A1 - Schröpfer, Dirk A1 - Wesling, Volker A1 - Kannengießer, Thomas T1 - Effect of alloy modification on the wear protection coatings made of Ni- and Co-based materials and surface machinability via ultrasonic milling process N2 - AbstractWear-resistant coatings are required for highly efficient and economical steel components in equipment, process, and power plant engineering to withstand high corrosive, tribological, thermal, and mechanical stresses. Co-alloys are used as wear-resistant coatings for steel components, tailored to the specific application. The substitutability of Co alloys with Ni-based wear protection systems, in addition to price and supply uncertainties, is facilitated by the combination of innovative welding and machining processes such as ultrasonic-assisted milling. The aim of the study is to improve the machinability of two different hard-facing alloys while maintaining the same wear protection potential. Therefore, the wear-resistant alloys NiMoCrSi (Colmonoy C56) and CoMnCrSi (Tribaloy T400) were modified by the alloying additions Nb, Hf, and Ti and then applied to a carbon-manganese steel S355 using the plasma transfer arc (PTA) welding process. The influence of the alloying additions on the microstructure as KW - Wear resistance KW - Co-based alloy KW - Ni-based alloy KW - PTA welding process KW - Ultrasonic assisted milling process PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-623931 DO - https://doi.org/10.1007/s00170-024-14955-0 SN - 0268-3768 SP - 1 EP - 17 PB - Springer Science and Business Media LLC AN - OPUS4-62393 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Liepold, Philipp A1 - Kromm, Arne A1 - Kannengießer, Thomas T1 - Transvarestraint testing of high-strength steel filler metal N2 - High-strength steel welds are typically not known to be susceptible to Solidification Cracking (SC). However, modern light-weight constructions may force welding in highly restrained conditions, which are known to increase the probability of Solidification Crack (SC) emergence. In this article, the Modified Varestraint-Transvarestraint (MVT) test was used to evaluate the hot cracking susceptibility of welds made from high-strength, low-alloyed filler material. The materials tested include solid wires and a metal-cored wire. All wires are typically used in the Gas Metal Arc Welding (GMAW) process. Susceptibility to SC was measured over a wide range of welding parameters and bending speeds. Results show little affinity of the tested materials to SC. However, crack length increases in most cases with arc energy ( U ∙ I∕welding speed ) and welding speed. The length of the longest crack in one test specimen follows a similar trend until high welding speeds, where stagnation of crack length with changing arc energy was observed. KW - MVT KW - Varestraint KW - Transvarestraint KW - Solidification cracking KW - High-strength steel PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-630084 DO - https://doi.org/10.1007/s40194-025-02042-1 SN - 1878-6669 VL - 2025 SP - 1 EP - 12 PB - Springer CY - Berlin ; Heidelberg AN - OPUS4-63008 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Michalska, Karina A1 - Heiermann, Monika A1 - Lühr, Carsten A1 - Meermann, Björn A1 - Pecenka, Ralf A1 - Schulz, Andreas A1 - Langhammer, Nicole A1 - Theuerl, Susanne A1 - Prochnow, Annette T1 - Potentials of typical plant species from rewetted fenlands for the supply of strategic elements N2 - Rewetting of peatlands requires the development of new biomass utilization pathways. The supply of strategic elements with key importance for the development of priority technologies, such as germanium (Ge), silicon (Si) and rare earth elements, from fenland plants is one option. To provide a first estimation of the potential, concentrations of strategic elements were determined in nine biomass samples covering typical fenland vegetation in northeast Germany. Subsequently, a simplified estimation of potential revenue from strategic element recovery was made. The analysed plant species can be classified as high or intermediate Si plant accumulators with highest contents of more than 16.0 g Si kg−1 dry mass (DM) in sedges and common reeds. Ge concentrations were lower with reed canary grass containing the highest amounts of 465.3 µg Ge kg−1 DM. Simultaneous acquisition of Ge and Si could provide higher total element yields and revenues of up to 500 $ ha−1. In contrast, the potentials for supplying rare earth elements appeared to be very low, with common reed containing the highest sum of rare earth elements of 437.4 µg kg−1 DM. Biomass from rewetted fenlands is capable of accumulating strategic elements. More knowledge is required to understand the factors affecting their accumulation. KW - Recycling KW - Fenlands KW - Strategic elements PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-635631 DO - https://doi.org/10.1038/s41598-025-05180-0 SN - 2045-2322 VL - 15 IS - 1 SP - 1 EP - 14 PB - Springer Science and Business Media LLC AN - OPUS4-63563 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Fink, Friedrich A1 - Stawski, Tomasz M. A1 - Emmerling, Franziska A1 - Falkenhagen, Jana T1 - A novel machine-learning approach to unlock technical lignin classification by NIR spectroscopy - bench to handheld N2 - In this research, the utilization of near-infrared (NIR) spectroscopy in conjunction with advanced machine learning methods is investigated for categorizing technical lignins obtained from different biomass sources and industrial procedures. Technical lignins, such as kraft, organosolv and lignosulfonates, have different chemical compositions, which continue to make uniform characterization and application in sustainable sectors extremely difficult. Fast, universally accessible analytics combined with data analysis is still an open question. For the first time three distinct NIR spectrometers—a high-performance benchtop system, a mid-priced compact device, and an economical handheld unit—were utilized to record NIR spectra of 31 unique lignin samples. The spectra underwent pre-processing through standard normal variate (SNV) transformation and Savitzky-Golay derivatives to amplify spectral features and decrease noise. Principal component analysis (PCA) was employed to reduce data complexity and extract crucial characteristics for classification purposes. Subsequently, four machine learning algorithms—Support Vector Machines (SVM), Gaussian Naive Bayes (GNB), Gaussian Process Classification (GPC), and Decision Tree Classification (DTC)—were implemented for the classification of the lignin samples. The DTC model exhibited the highest accuracy among them across different spectrometers. Although the benchtop spectrometer produced the most precise outcomes, the compact NeoSpectra system also displayed potential as a cost-efficient option. Nonetheless, the restricted spectral coverage of the handheld NIRONE spectrometer resulted in reduced classification accuracy. Our discoveries highlight the capability of NIR spectroscopy, combined with robust data analysis techniques, for the swift and non-destructive classification of technical lignins, facilitating their improved utilization in sustainable fields. KW - Technical lignins KW - NIR spectroscopy KW - Classification KW - Machine-learning KW - PCA PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-634518 DO - https://doi.org/10.1016/j.chemolab.2025.105467 SN - 0169-7439 VL - 264 SP - 1 EP - 10 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-63451 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zhuang, Yiling A1 - Haderlein, Stefan B. A1 - Lutze, Holger V. A1 - Sun, Chen A1 - Fink, Friedrich A1 - Paul, Andrea A1 - Spahr, Stephanie T1 - Persulfate activation by biochar for trace organic contaminant removal from urban stormwater N2 - Persistent and mobile trace organic contaminants (TrOCs) in urban stormwater are difficult to remove through sedimentation- or sorption-based treatment and pose a risk to aquatic ecosystems and drinking water supplies. We demonstrate that the chemical oxidant peroxydisulfate (PDS) can be activated by shrimp shell biochar at pH 7 to form reactive species that selectively react with widespread stormwater contaminants. Of 11 TrOCs tested, oxidative transformation was observed for 1,3-diphenylguanidine, 2-hydroxybenzothiazole, 1H-benzotriazole, 5-methyl-benzotriazole, and diuron during water treatment with biochar and PDS. Laboratory batch experiments conducted with street runoff and a synthetic water showed that the water matrix, containing up to 7.5 mg L-1 dissolved organic carbon and 100 mM chloride, had a minor effect on the formation of reactive species and contaminant transformation. Using a set of scavengers and probe compounds, we provide evidence for singlet oxygen (1O2) as the predominant reactive species in the biochar/PDS system, which is in agreement with the selectivity of the process to oxidize electron-rich organic contaminants. The results of our study inform new strategies for stormwater treatment using heterogeneous oxidation processes for the abatement of persistent and mobile organic contaminants. KW - Stormwater treatment KW - Oxidation processes KW - Pyrogenic carbon PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-637952 DO - https://doi.org/10.1016/j.watres.2025.123921 SN - 0043-1354 VL - 284 SP - 1 EP - 8 PB - Elsevier Ltd. AN - OPUS4-63795 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Rosenbusch, Ivo A1 - Arai, Marylyn Setsuko A1 - Rizzo, Fabio A1 - de Camargo, Andrea S. S. A1 - Ravoo, Bart Jan T1 - A host–guest approach to ratiometric pH sensing using upconversion nanoparticles N2 - A new pH nanosensor based on β-NaYF4:Yb3+/Tm3+ upconversion nanoparticles functionalized with cyclodextrin and a pH-sensitive adamantane-modified nitrobenzoxadiazole dye (NBD-Ad). KW - Host-guest materials KW - Upconversion nanoparticles KW - Ratiometric optical sensors KW - pH sensing PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-637722 DO - https://doi.org/10.1039/d5na00145e SN - 2516-0230 VL - 7 IS - 13 SP - 4142 EP - 4151 PB - Royal Society of Chemistry (RSC) AN - OPUS4-63772 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bourgon, Nicolas A1 - Oelze, Marcus A1 - Roberts, Patrick T1 - Less is more: Limiting semi-invasive sampling for multi-isotope analyses and increasing data output from single aliquot samples N2 - Developments in multi-isotope applications now enable the production of direct and precise life history data of studied archeological and paleoanthropological specimens, with analysis of tooth enamel proving particularly powerful in deep-time preservation contexts. However, the increasing amount of sample material necessary too-often compromises the specimen's structural integrity. Finding ways of minimizing semi-invasive sampling while maximizing produced data thus becomes increasingly crucial. In this study, we examine ways of optimizing sample use for state-of-the-art isotope measurements of enamel-bound zinc (δ66Zn), an increasingly used method in multi-isotope archeological research. We show that certain desolvating nebulizer introduction systems can be used to measure δ66Zn with high efficiency and accuracy using less than half the usual sample size. Moreover, we demonstrate that remaining samples subjected to typical pretreatments used for tooth enamel carbonate (δ13C and δ18O) studies can be safely used without alterations to δ66Zn values. Similarly, we highlight that the often-discarded matrix fraction from zinc chromatography can be utilized for further analyses, such as measurements of 87Sr/86Sr ratios. Our results underscore the possibility of extracting the maximum information from specimens while altogether avoiding or significantly reducing semi-invasive sampling. KW - Multi-isotope KW - Zinc isotope analysis KW - Tooth enamel PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-637986 DO - https://doi.org/10.1016/j.jas.2025.106308 SN - 0305-4403 VL - 180 SP - 1 EP - 8 PB - Elsevier Ltd. AN - OPUS4-63798 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Go, Eun Sul A1 - Hong, Eun Ji A1 - Lee, Ji Yeong A1 - Stolar, Tomislav A1 - Peterson, Gregory I. A1 - Emmerling, Franziska L. A1 - Kim, Kyoungsoo A1 - Kim, Jeung Gon T1 - Insights into Mechanochemical Solid-State Ball-Milling Reaction: Monitoring Transition from Heterogeneous to Homogeneous Conditions N2 - As mechanochemical synthesis has advanced significantly, there has been intense interest in understanding the underlying mechanisms of these reactions. Given that many mechanochemical processes are conducted in the solid-state without solvation yet sometimes yield faster reactions than those in solution, we sought to address the following question: Are mechanochemical reactions homo- or heterogeneous? To investigate, we employed a model system involving the mixing and copolymerization of l-lactide (LLA) and d-lactide (DLA), monitored through powder X-ray diffraction (PXRD), nuclear magnetic resonance, and differential scanning calorimetry. In situ and ex situ PXRD analyses of the mixture of LLA and DLA showed that vibratory ball milling rapidly transformed the initially heterogeneous lactide mixture into a homogeneous phase within one min due to collisions between the balls and the jar. By varying the milling conditions, we were able to regulate the level of mixing, which subsequently influenced the copolymerization outcomes. In the solid-state ball-milling copolymerization of LLA and DLA in the presence of a catalyst and initiator, multiblock copolymers of poly(l-lactic acid) and poly(d-lactic acid) were formed within one min during the early stage of the reaction, when incomplete mixing of the monomers led to a process governed by phase heterogeneity. In contrast, prolonged polymerization promoted conditions approaching homogeneity, ultimately yielding atactic poly(lactic acid). This transition from heterogeneous to homogeneous reactions is a distinctive feature compared to conventional homogeneous reactions, potentially leading to mechano-exclusive reaction designs. KW - Mechanochemistry KW - Ball-milling KW - Homogeneous reaction KW - Heterogeneous reaction PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-638008 DO - https://doi.org/10.1021/jacsau.5c00322 SN - 2691-3704 VL - 5 IS - 6 SP - 2720 EP - 2727 PB - American Chemical Society (ACS) AN - OPUS4-63800 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Popiela, Bartosz A1 - Günzel, Stephan A1 - Schukar, Marcus A1 - Mair, Georg W. A1 - Krebber, Katerina A1 - Seidlitz, Holger T1 - Impact of internal pressure control during manufacturing on residual stresses and safety performance of type 4 pressure vessels N2 - Composite pressure vessels are commonly manufactured using the wet filament winding process, where various process parameters can influence the performance of the finished component. In this study two designs of wet filament wound 6.8-liter type 4 composite pressure vessels were manufactured. Both differ only by the internal pressure used during the filament winding, which primarily influences the residual stress state in the composite structure. An extensive experimental study was carried out, including 10 slow burst tests and strain measurements with fiber optic sensors. Significant differences can be observed in the performance of the two designs even though the used stacking sequence, materials and other manufacturing parameters are the same for both designs. A discussion of the differences in the behavior of both cylinder types is provided, including the strain distribution in slow burst tests and failure mechanism. KW - Residual stresses KW - Slow burst tests KW - Filament winding KW - Type 4 composite pressure vessels KW - Hydrogen PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-626663 DO - https://doi.org/10.1016/j.jcomc.2025.100581 SN - 2666-6820 VL - 17 SP - 1 EP - 9 PB - Elsevier B.V. CY - Amsterdam, Netherlands AN - OPUS4-62666 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Xie, Zhuocheng A1 - Atila, Achraf A1 - Guénolé, Julien A1 - Korte-Kerzel, Sandra A1 - Al-Samman, Talal A1 - Kerzel, Ulrich T1 - Predicting grain boundary segregation in magnesium alloys: An atomistically informed machine learning approach N2 - Grain boundary (GB) segregation substantially influences the mechanical properties and performance of magnesium (Mg). Atomic-scale modeling, typically using ab-initio or semi-empirical approaches, has mainly focused on GB segregation at highly symmetric GBs in Mg alloys, often failing to capture the diversity of local atomic environments and segregation energies, resulting in inaccurate structure-property predictions. This study employs atomistic simulations and machine learning models to systematically investigate the segregation behavior of common solute elements in polycrystalline Mg at both 0 K and finite temperatures. The machine learning models accurately predict segregation thermodynamics by incorporating energetic and structural descriptors. We found that segregation energy and vibrational free energy follow skew-normal distributions, with hydrostatic stress, an indicator of excess free volume, emerging as an important factor influencing segregation tendency. The local atomic environment’s flexibility, quantified by flexibility volume, is also crucial in predicting GB segregation. Comparing the grain boundary solute concentrations calculated via the Langmuir-McLean isotherm with experimental data, we identified a pronounced segregation tendency for Nd, highlighting its potential for GB engineering in Mg alloys. This work demonstrates the powerful synergy of atomistic simulations and machine learning, paving the way for designing advanced lightweight Mg alloys with tailored properties. KW - Machine learning KW - Grain boundary segregation KW - Magnesium alloys KW - Atomistic simulation PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-638499 DO - https://doi.org/10.1016/j.jma.2025.03.021 SN - 2213-9567 VL - 13 IS - 6 SP - 2636 EP - 2650 PB - Elsevier B.V. AN - OPUS4-63849 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Yang, Chunliang A1 - Yang, Fan A1 - Meng, Xiangmeng A1 - Putra, Stephen Nugraha A1 - Bachmann, Marcel A1 - Rethmeier, Michael T1 - Multi-refining effects of an AC electromagnetic field on the microstructure in AA5754 laser beam welding N2 - Fine-grain structure is beneficial to the mechanical properties of the joint. Different kinds of grain and sub-grain structures refined by magnetic field during laser beam welding of AA5754 aluminum alloy are analyzed in this manuscript, and the influences of different magnetic field parameters (magnetic flux density and frequency) in these refining effects are also studied. Using the scanning electron microscope (SEM), the sub-grain structure near the fusion line was obtained, and it was found that the branching promotion and branches refinement can be achieved by the magnetic field. The branches become finer with the magnetic flux density or frequency increases, and this effect is stronger in the dendritic region than in the equiaxed region. The results of electron backscatter diffraction (EBSD) in the equiaxed region show that a high-frequency magnetic field can greatly reduce the average grain size, while a low-frequency one has little effect. A phenomenological nucleation model based on dendrite fragmentation theory was established, and it was introduced into the phase field model to analyze the equiaxed grains evolution process. In addition, another refinement mechanism was also observed. The periodic solidification pattern caused by the unstable solidification in the molten pool can refine the grains, and the magnetic field promotes this kind of grain refinement by promoting the solidification period. KW - Laser beam welding KW - Magnetic field KW - Aluminum alloy KW - Crystal branch development KW - Periodic solidification pattern KW - Grain refinement PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-637222 DO - https://doi.org/10.1016/j.ijheatmasstransfer.2025.127509 SN - 0017-9310 VL - 252 SP - 1 EP - 16 PB - Elsevier Ltd. AN - OPUS4-63722 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Paul, Sagar A1 - Dolai, Malay A1 - Nanda Goswami, Juli A1 - Bhattacharya, Biswajit A1 - Emmerling, Franziska A1 - Drew, Michael G. B. A1 - Chattopadhyay, Shouvik A1 - Sarkar, Rabi Sankar A1 - Sunil, Appu A1 - Novitchi, Ghenadie A1 - Moreno-Pineda, Eufemio A1 - Wernsdorfer, Wolfgang T1 - From strong to weak interaction: Reconciling SQUID and μSQUID-EPR data in anomalous Co(ii) dimers N2 - Magnetic molecules have been proposed as scaffolds for novel quantum technologies, ranging from quantum sensing and quantum memory to multilevel quantum bits (qudits) and fault-tolerant quantum computation. Integration of magnetic molecules into cutting-edge applications hinges on a deep understanding and tunability of their spin states. To date, the strategic manipulation of the local environment of the ion and careful selection of the magnetic core have enabled the desired tunability and scalability of the spin states. For such goals, however, extracting the anisotropic parameters that dictate the characteristics of the Spin Hamiltonian is challenging, especially for molecules consisting of multiple magnetic cores. We address these challenges by studying two cobalt(II) dinuclear systems, complicated by inherent spin–orbit coupling. We explore the magnetic properties of these systems in two temperature regimes: (i) at sub-Kelvin temperatures employing single crystals at 30 mK using a unique μSQUID-EPR technique that examines the microwave absorption peaks in the magnetisation data and their variation with field angle and frequency; and (ii) in bulk employing convectional SQUID magnetometry above 2 K i.e., χMT(T) and M(H). Unexpectedly, sub-Kelvin temperature investigations reveal a negligible interaction, whereas the SQUID data reveal a much stronger interaction between the Co(II) ions. An understanding of these data is developed based on a strong coupling model and the coupling of two moieties with a spin-effective ground state. KW - cOBALT(II)-complex KW - In situ complex formation KW - Magnetic property KW - Crystal structure PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-641421 DO - https://doi.org/10.1039/D5QI01387A SN - 2052-1553 SP - 1 EP - 13 PB - Royal Society of Chemistry (RSC) CY - Cambridge AN - OPUS4-64142 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Seifert, Lando A1 - Müller, Thoralf A1 - Bettge, Dirk A1 - Moersch, Jörg A1 - Isecke, Bernd A1 - Ebell, Gino T1 - Stress Corrosion Tests for Prestressing Steels—Part 2: Susceptibility of Quenched and Tempered Wires—Influence of Chromium N2 - Due to the risk of failure in existing prestressed concrete bridges, the assessment of the susceptibility of prestressing steel to hydrogen‐induced stress corrosion cracking will become more important in the future. At present, the used normative ISO 15630‐3 test gives unpersuasive and diverging results using a free corrosion approach for the needed hydrogen charging for stress corrosion cracking initiation. A newly developed test method uses the cathodic polarization to control the supply of electrons for hydrogen charging instead of an uncontrolled and variable supply of electrons by metal dissolution during free corrosion. Experimental data shows a reliable differentiation between highly susceptible known quenched and tempered wires and robust cold‐drawn wires with this new test. A round robin with eight participating testing institutes demonstrated the reproducibility of results testing a cold‐drawn wire batch of St 1470/1670. In contrast to previously reported experience in the literature, the new method ranks the Cr‐alloyed quenched and tempered (“new‐type”) wires as highly‐susceptible as the “old‐type” wires without Cr‐alloy. KW - Cathodic polarization KW - Chemical composition KW - Chromium KW - Prestressing steels KW - Quenched and tempered KW - Stress corrosion cracking KW - Susceptibility KW - Wires PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-639735 DO - https://doi.org/10.1002/maco.70033 SN - 0947-5117 SP - 1 EP - 10 PB - Wiley-VCH CY - Weinheim AN - OPUS4-63973 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Janczynski, Jessica A1 - Tewes, Andreas A1 - Ulbricht, Alexander A1 - Jaenisch, Gerd-Rüdiger T1 - Evaluation Metrics for Comparison between Virtual and Industrial XCT N2 - Simulations of XCT systems, as employed in the context of the manufacturing and design process, represent a time-saving, cost- and resource-efficient alternative to repeated experimental measurements. This article is dedicated to the development and evaluation of various metrics that should enable an adequate verification and optimization of a XCT simulation of an experimental XCT system. The present study employed statistical evaluation as a methodological approach. The present article makes a significant contribution to the optimization of the development process of a XCT simulation and provides a foundation for future research activities in this field. KW - Computed Tomography KW - Computertomographie KW - aRTist KW - Simulation KW - Virtual CT KW - Evaluation PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-641444 DO - https://doi.org/10.1007/s10921-025-01213-w SN - 0195-9298 VL - 44 IS - 4 SP - 1 EP - 11 PB - Springer Science and Business Media LLC CY - Berlin/Heidelberg AN - OPUS4-64144 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Biegler, Max A1 - Yang, Keke A1 - Meschut, Gerson A1 - Rethmeier, Michael T1 - Occurrence and avoidance of liquid metal embrittlement in resistance spot welding of springback-afflicted deep-drawn components N2 - This study investigates the occurrence and mitigation of liquid metal embrittlement occurring during resistance spot welding in deep-drawn automotive components, specifically focusing on an S-Rail made from advanced high-strength steel. A simulation-based liquid metal embrittlement risk criterion based on local major component stresses was established and used to quantify and compare liquid metal embrittlement risks between different tests. Experimental and numerical analyses were conducted, revealing that springback significantly impacts liquid metal embrittlement formation. Adjustments in electrode geometry and hold time post-welding were found to mitigate liquid metal embrittlement risks. The effects of stack-up configuration and related parameter settings on liquid metal embrittlement occurrence were identified and liquid metal embrittlement was effectively prevented across both stack-up configurations. These findings advance the understanding of liquid metal embrittlement mechanisms and provide practical approaches to enhance the spot weld quality in AHSS-based body-in-whites. KW - Liquid metal embrittlement KW - Crack KW - Advanced high-strength steels KW - Resistance spot welding KW - Weld current KW - Heat input KW - Simulation KW - Springback KW - Deep drawing KW - S-Rail PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-636577 DO - https://doi.org/10.1177/13621718251340452 SN - 1362-1718 SP - 1 EP - 9 PB - SAGE Publications AN - OPUS4-63657 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Grohmann, Maria A1 - Maack, Stefan A1 - Behrens, Matthias A1 - Niederleithinger, Ernst T1 - Low-frequency ultrasonic pulse-echo datasets for geometry determination of a reinforced concrete step specimen with embedded polystyrene foam cuboids in non-destructive testing N2 - The dataset comprises raw data collected using the ultrasonic pulse-echo method on a concrete specimen. The specimen addresses two fundamental non-destructive testing (NDT) challenges in civil engineering: locating built-in elements and determining dimensions to analyse both the internal and external geometry of concrete structures. For data acquisition, the surface of the concrete specimen was automatically scanned point by point, with pulse-echo measurements performed at each measuring point. The automation of the measurement process ensured high repeatability and precision as well as a high measurement point density. Two low-frequency probes were used, each capable of both transmitting and receiving ultrasonic waves: one for longitudinal waves and one for shear waves. The longitudinal wave probe operates at frequencies of up to approximately 160 kHz, whereby a frequency of 80 kHz was used for the ultrasonic measurements here. The shear wave probe operates at up to 100 kHz, with a frequency of 50 kHz used for the measurements in this study. This article includes additional technical specifications of the two ultrasonic probes used, as well as information on their geometric specifications and directivity patterns. It also provides a detailed description of the further measurement equipment used. The ultrasonic raw data are stored in a universally readable format, with each time signal (A-scan) spanning two milliseconds and a sampling rate of two mega-samples per second. The provided data support comparative studies in signal analysis, imaging as well as interpretation and can be used for evaluation purposes in various practical NDT scenarios. KW - Civil engineering KW - Concrete structures KW - Ultrasonic echo testing KW - Reference data PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-639100 DO - https://doi.org/10.1016/j.dib.2025.111956 SN - 2352-3409 VL - 62 SP - 1 EP - 19 PB - Elsevier Inc. AN - OPUS4-63910 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Liao, Chun-Man A1 - Niederleithinger, Ernst A1 - Bernauer, F A1 - Igel, H A1 - Hadziioannou, Céline T1 - Wave-Screening Methods for Prestress-Loss Assessment of a Large-Scale Post-Tensioned Concrete Bridge Model Under Outdoor Conditions N2 - This paper presents advancements in structural health monitoring (SHM) techniques, with a particular focus on wave-screening methods for assessing prestress loss in a large-scale prestressed concrete (PC) bridge model under outdoor conditions. The wave-screening process utilizes low-frequency wave propagation obtained from seismic interferometry of structural free vibrations and high-frequency wave propagation obtained through ultrasonic transducers embedded in the structure. An adjustable post-tensioning system was employed in a series of experiments to simulate prestress loss. By comparing bridge vibrations under varying post-tensioning forces, the study investigated prestress loss and examined temperature-related effects using the coda wave interferometry (CWI) method. Local structural alterations were analyzed through wave velocity variations, demonstrating sensitivity to bridge temperature changes. The findings indicate that wave-based methods are more effective than traditional modal analysis for damage detection, highlighting the dual impacts of prestress loss and temperature, as well as damage localization. This study underscores the need for long-term measurements to account for temperature fluctuations when analyzing vibration measurements to investigate changes in prestressing force in PC structures. KW - Coda wave interferometry KW - Damage detection KW - Prestress loss KW - Seismic interferometry KW - SHM KW - Temperature influence KW - Ultrasonics KW - Wave-screening PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-634244 UR - https://www.mdpi.com/2076-3417/15/11/6005 DO - https://doi.org/10.3390/app15116005 VL - 15 IS - 11 SP - 1 EP - 18 PB - MDPI AN - OPUS4-63424 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, Vinzenz A1 - Fasselt, Janek Maria A1 - Klötzer-Freese, Christian A1 - Kruse, Tobias A1 - Kleba-Ehrhardt, Rafael A1 - Biegler, Max A1 - Rethmeier, Michael T1 - Recycling nickel aluminium bronze grinding chips to feedstock for directed energy deposition via impact whirl milling: Investigation on processability, microstructure and mechanical properties N2 - During the production of ship propellers, considerable quantities of grinding chips from nickel aluminium bronze are produced. This paper examines the mechanical comminution of such chips via impact whirl milling and the utilization of two chip-powder batches as feedstock for a laser-based directed energy deposition process. The materials are characterized via digital image analysis, standardized flowability tests, scanning electron microscopy and energy dispersive X-ray spectroscopy and are compared to conventional, gas atomized powder. The specimens deposited via directed energy deposition are analyzed for density, hardness and microstructure and tensile properties for vertical and horizontal build up directions are compared. At elevated mill rotation speeds, the comminution with impact whirl milling produced rounded particles, favorable flow properties and particle size distribution, making them suitable to deposit additive specimens. The microstructure exhibited characteristic martensitic phases due to the high cooling rates of the additive manufacturing process. The presence of ceramic inclusions was observed in both the powder and on the tensile fracture surfaces, partly impairing the mechanical properties. However, specimens in the vertical build-up direction (Z) showed competitive tensile results, with 775 MPa in tensile strength, 455 MPa in yield strength and 12.6 % elongation at break. The findings of this study indicate that recycling of machining chips to additive manufacturing feedstock can be a viable option for reducing material costs and environmental impact. KW - Nickel aluminium bronze KW - Grinding chips KW - Recycling KW - Directed energy deposition KW - Material characterization PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-633442 DO - https://doi.org/10.1016/j.addma.2025.104804 SN - 2214-8604 VL - 105 SP - 1 EP - 9 PB - Elsevier BV AN - OPUS4-63344 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Scharek, Vera M. A1 - Pfeifer, Jens A1 - Vogl, Jochen A1 - Traub, Heike A1 - Meermann, Björn T1 - Tin fractionation analysis in sediment samples via on-line ID ETV/ICP-MS N2 - We report a quantification approach for directly determining total tin and tin-based pollutants/species in sediments via electrothermal vaporization/inductively coupled plasma-mass spectrometry (ETV/ICP-MS) utilizing an on-line isotope dilution mass spectrometry (IDMS) approach. The method was developed and validated using an estuarine sediment reference material (BCR-277R), yielding a recovery of 106%. A relative standard deviation (RSD) of 14%, comparable to published data using a similar method, was obtained. A limit of quantification (LOQ) was estimated at 0.008 mg Sn kg−1 and sufficient for quantifying the total tin mass fraction of surface sediments along the tidal River Elbe course. Hereby, a decrease towards the river mouth, presumably due to dilution effects by less polluted marine sediment, was observed. Besides total tin, monitoring of organotin compounds (OTCs)/species is of interest in sediments due to their toxic effects on aquatic life. The method’s capability was extended by separating an OTC fraction in a sediment certified reference material (CRM) through the ETV temperature program. While spiking experiments with OTC standards confirmed the assignment, only a small fraction of the total certified OTC amount (3%), likely due to matrix effects, was recovered. However, applying the method to real-world samples, OTCs were detectable along the River Elbe course. By this, we demonstrated the potential of our method as a complementary fast-screening approach to species-specific analysis procedures. KW - ETV KW - Sn-Speciation KW - Sediment PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-640137 DO - https://doi.org/10.1007/s00216-025-06064-y SN - 1618-2642 SP - 1 EP - 10 PB - Springer Science and Business Media LLC AN - OPUS4-64013 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Feord, Helen K. A1 - Trautwein-Schult, Anke A1 - Keuschnig, Christoph A1 - Ostrzinski, Anne A1 - Peter, Elisa K. A1 - Jaeger, Carsten A1 - Lisec, Jan A1 - Mourot, Rey A1 - Peters, Ravi Sven A1 - Çiftçi, Ozan A1 - Tranter, Martyn A1 - Anesio, Alexandre M. A1 - Becher, Dörte A1 - Benning, Liane G. T1 - Algae-dominated metaproteomes uncover cellular adaptations to life on the Greenland Ice Sheet N2 - Eukaryotic algae-dominated microbiomes thrive on the Greenland Ice Sheet (GrIS) in harsh environmental conditions, including low temperatures, high light, and low nutrient availability. Chlorophyte algae bloom on snow, while streptophyte algae dominate bare ice surfaces. Empirical data about the cellular mechanisms responsible for their survival in these extreme conditions are scarce. This knowledge gap was addressed by quantifying proteins for both algal taxa from samples on the southern margin of the GrIS. We show that the streptophyte glacier ice algae have a relative enrichment in proteins involved in environmental signaling and nutrient transport, indicative of cellular readiness to dynamically respond to extreme GriS environmental cues, linked, for example, to photoprotection and the rapid update of scarce nutrients. In contrast, the chlorophyte snow algae have a high abundance of proteins linked to lipid and nitrogen metabolisms, providing evidence for the biological processes sustaining the cellular carbon and nitrogen stores necessary for survival in an oligotrophic environment. We also identify proteins in both taxa linked to the synthesis and breakdown of key cellular pigments. Our study gives novel insights into the cellular biology of these algae and their adaptation to extreme environments. KW - Metabolic profiling KW - Mass spectrometry KW - Ice algae PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-641037 DO - https://doi.org/10.1038/s41522-025-00770-2 SN - 2055-5008 VL - 11 IS - 1 SP - 1 EP - 11 PB - Springer Science and Business Media LLC AN - OPUS4-64103 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Savitsky, Viktor A1 - Schmies, Lennart A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael T1 - Comparative performance of DIC and optical flow algorithms for displacement and strain analysis in laser beam welding N2 - The measurement of strain and displacement in the context of the welding process represents a significant challenge. Optical methods, such as digital image correlation (DIC) or optical flow algorithms, have demonstrated their efficacy in robust and reliable data acquisition in harsh environments, including those encountered in welding processes. Concurrently, a trade-off between the accuracy of the measurement and the computational resources required for the associated calculations must be evaluated on a case-by-case basis. The application of filters to initial images represents a technique that serves to enhance the quality and accuracy of the strain and displacement prediction. In the present study, the estimated error of two algorithms, namely the Lucas-Kanade (LK) and the inverse compositional Gauss-Newton (IC-GN), is compared on the basis of both synthetic and real welding images. The displacement field is evaluated for different zones in the laser weld seam with varying contrast performance. Based on the aforementioned results, a strain calculation was conducted for both methods, which yielded comparable results for the LK and IC-GN algorithms. KW - Laser speckle KW - DIC KW - Optical flow KW - Error estimation KW - Strain measurement KW - Laser beam welding PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-625919 DO - https://doi.org/10.1016/j.optlaseng.2025.108870 SN - 1873-0302 VL - 187 SP - 1 EP - 15 PB - Elsevier Ltd. AN - OPUS4-62591 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schannor, Mathias A1 - Oelze, Marcus A1 - Traub, Heike A1 - He, Yubei A1 - Schmidt, Robin A1 - Heidemann, Luisa A1 - Savic, Lynn Jeanette A1 - Vogl, Jochen A1 - Meermann, Björn T1 - Advancing Biomarker Research: In Situ Cu Isotope Analysis in Liver Tumors by LA-MC-ICP-MS N2 - Stable metal isotopes have received increasing attention as medical biomarkers due to their potential to detect changes in metal metabolism related to diseases. In particular, copper stable isotopes are a powerful tool to identify isotopic variation between tumors and healthy tissue, suggesting application in cancer diagnosis. However, potential mechanisms causing isotope fractionation, such as redox- or bond-forming reactions and interactions of metals during transmembrane import and export, are less well understood. Here, we established an in situ method using laser ablation-multicollector-inductively coupled plasma-mass spectrometry (LA-MC-ICP-MS) to advance our understanding of the underlying processes responsible for isotope fractionation between normal and diseased tissues. Gelatin-based bracketing standards and quality control reference materials, crucial for laser ablation analysis, were developed to allow correction for instrumentally induced isotope fractionation during LA-MC-ICP-MS analysis. Using such matrix-matched standards, the method achieved intermediate precisions for delta values of better than 0.15 ‰ (2 s) for inorganic reference materials and of better than 0.17 ‰ (2 s) for biological reference materials. The developed routine was tested on rabbit VX2 liver tumor samples, a model system resembling human hepatocellular carcinoma (HCC) used to study liver cancer. In situ Cu isotope compositions between healthy (𝛿65/63NIST976(Cu) = −1.5 ‰ to 0.2 ‰) and tumorous (𝛿65/63NIST976(Cu) = 0.0 ‰ to 1.3 ‰) liver tissue show distinct differences in their isotope ratios. The observed isotopic dichotomy is consistent with previous solution-based MC-ICP-MS work, showing enrichment of heavy 65Cu in cancer biopsies relative to healthy tissue. KW - Biomarker KW - Laser Ablation KW - Reference Material PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-626865 DO - https://doi.org/10.1021/acs.analchem.4c05626 SN - 1520-6882 VL - 97 IS - 8 SP - 4425 EP - 4432 PB - American Chemical Society (ACS) AN - OPUS4-62686 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Epple, Niklas A1 - Schumacher, Thomas A1 - Murtuz, A. K. M. Golam A1 - Niederleithinger, Ernst A1 - Dusicka, Peter T1 - Combined passive and active ultrasonic stress wave monitoring of a full‑scale laboratory reinforced concrete bridge column subject to reverse‑cyclic lateral loading N2 - Effective monitoring of reinforced concrete structures requires techniques that detect early-stage material change and active, localized cracking. This study investigates a combined structural health monitoring approach using passive acoustic emission and active ultrasonic methods on a full-scale reinforced concrete bridge column subjected to reverse-cyclic lateral loading. Active monitoring, based on coda wave interferometry, was used to track changes in wave velocity and waveforms, while passive acoustic emission monitoring was used to detect crack activity. The instrumentation consisted of three embedded ultrasonic transducers and three surface-mounted acoustic emission sensors. The results show that active ultrasonic monitoring is most effective prior to visual damage, successfully detecting the onset of internal cracking via wave velocity decreases exceeding 0.4%, and distinguishing load-induced effects from permanent damage. However, its utility diminished in later stages of damage progression, as strong signal decorrelation hindered further data interpretation. Additionally, active US measurements allowed a comparison of damage severity in different parts of the column. Conversely, passive acoustic emission monitoring effectively tracked the formation of concrete cracks throughout the experiment, with distinct event clusters and high-amplitude signals (> 60 dB) confirming ongoing fracture processes in all damage states. This study confirms that combining these methods results in a more robust structural health monitoring strategy by leveraging their complementary strengths. Active techniques excel at tracking continuous material changes in early damage states, while passive methods are superior for detecting discrete cracking events as damage progresses. Importantly, both methods can utilize the same measurement equipment, enabling a cost-effective approach to continuous damage tracking. KW - Coda wave interferometry KW - Active ultrasonic monitoring KW - Acoustic emission KW - Structural health monitoring KW - Nondestructive evaluation PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-638689 DO - https://doi.org/10.1007/s13349-025-00996-w SN - 2190-5479 SP - 1 EP - 24 PB - Springer Nature AN - OPUS4-63868 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Löwa, N. A1 - Golusda, L. A1 - Paclik, D. A1 - Traub, Heike A1 - Schannor, Mathias A1 - Saatz, Jessica A1 - Freise, C. A1 - Taupitz, M. A1 - Siegmund, B. A1 - Kühl, A. A. A1 - Wiekhorst, F. T1 - Magnetic particle spectroscopy for Eu-VSOP quantification in intestinal inflammation: Distinguishing nanoparticle signals from dietary contamination N2 - Magnetic nanoparticles are gaining increasing attention as a promising alternative to gadolinium-based contrast agents in magnetic resonance imaging, primarily due to their low toxicity. In this study, we investigated the use of magnetic iron oxide nanoparticles in mouse models of intestinal inflammation to assess their potential for detecting changes in the extracellular matrix. For magnetic quantification, we employed magnetic particle spectroscopy, which offers high sensitivity and minimal interference from biological tissue. However, we observed significant variations in magnetic signals within the intestine, as well as measurable signals in control animals, indicating possible magnetic contamination. By doping the nanoparticles with europium, we were able to confirm this suspicion through quantitative elemental analysis. Examination of mouse feed and feces allowed us to identify the source of contamination. Based on these findings, we developed a method to reliably distinguish genuine signals of magnetic nanoparticles from those caused by external magnetic contaminations. This approach is essential to ensure reliable results in future diagnostic and preclinical research. KW - ICP-MS KW - Nanoparticle KW - Magnetic particle spectroscopy KW - Quantification PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-642238 DO - https://doi.org/10.1039/D5NA00452G SN - 2516-0230 IS - 00452 SP - 1 EP - 10 PB - Royal Society of Chemistry (RSC) CY - Cambridge AN - OPUS4-64223 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Walter, Keven A1 - Hoch, Dominik P. A1 - Hertweck, Leon A1 - Balasubramanian, Kannan A1 - Geisler, Jonas A1 - Röllig, Mathias A1 - Neubert, Tilmann J. A1 - Börner, Hans G. T1 - Unlocking the Essence of Lignin: High‐Performance Adhesives That Bond via Thiol‐Catechol Connectivities and Debond on Electrochemical Command N2 - AbstractThe next generation of adhesives requires effective debonding capabilities that can be triggered on demand to enable advanced circular repair and recycling strategies. A new class of lignin‐inspired, two‐component (2K) structural adhesives offers bonding strengths of up to 20 MPa and clean, on‐command electrochemical debonding within 5–30 min. The debonding is induced by a distinct electrochemical oxidation of thiol‐catechol connectivities (TCCs) within the entire adhesive network, enforcing rapid and clean adhesive failure on the cathodic substrate side. The TCC‐functionalities are formed during curing by a thiol‐quinone Michael‐type polyaddition, reacting polyester‐based trithiols with tris‐quinones as lignin‐inspired minimal building blocks. The structural adhesive can be fine‐tuned by adjusting the formulation. The addition of carbon black and ionic liquids facilitates the desired electrochemical transformation of TCC‐catechols to TCC‐quinones. Applying only 9 V for 5–30 min, leads to clean debonding with 72–86% loss of shear strength. A comprehensive study of curing, bonding, and debonding behavior by rheological, spectroscopic, and electrochemical investigations reveals the debonding mechanism by correlating catechol oxidation to adhesive performance. The electrochemical debonding capability of TCC‐structural adhesives is demonstrated in a functional prototype, where on‐command detachment of a cover glass from a display device is achieved within 6.5 min. KW - Lignin-inspired KW - Electrochemical-Debonding KW - Thiol-Catechol-Connectivity (TCC) KW - Michael-Type Polyaddition KW - On-Demand Adhesive Failure PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-639674 DO - https://doi.org/10.1002/adma.202510463 SN - 0935-9648 SP - 1 EP - 10 PB - Wiley VHC-Verlag CY - 69451 Weinheim AN - OPUS4-63967 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Das, Prasenjit A1 - Chakraborty, Gouri A1 - Yang, Jin A1 - Roeser, Jérôme A1 - Küçükkeçeci, Hüseyin A1 - Nguyen, Anh Dung A1 - Schwarze, Michael A1 - Gabriel, Jose A1 - Penschke, Christopher A1 - Du, Shengjun A1 - Weigelt, Vincent A1 - Khalil, Islam E. A1 - Schmidt, Johannes A1 - Saalfrank, Peter A1 - Oschatz, Martin A1 - Rabeah, Jabor A1 - Schomäcker, Reinhard A1 - Emmerling, Franziska A1 - Thomas, Arne T1 - The Effect of Pore Functionality in Multicomponent Covalent Organic Frameworks on Stable Long‐Term Photocatalytic H2 Production N2 - AbstractIn nature, organic molecules play a vital role in light harvesting and photosynthesis. However, regarding artificial water splitting, the research focus is primarily on inorganic semiconductors. Although organic photocatalysts have high structural variability, they tend to exhibit lower quantum efficiencies for water splitting than their inorganic counterparts. Multicomponent reactions (MCRs) offer an attractive route to introduce different functional units into covalent organic frameworks (COFs) and enable semiconducting properties and high chemical stability, creating promising materials for long‐term photocatalytic applications, such as H2 production. Herein, five highly crystalline donor‐acceptor based, 4‐substituted quinoline‐linked MCR‐COFs are presented that are prepared via the three‐component Povarov reaction. The pore functionality is varied by applying different vinyl derivatives (e.g., styrene, 2‐vinyl pyridine, 4‐vinylpyridine, 4‐vinyl imidazole, 2,3,4,5,6‐pentafluorostyrene), which has a strong influence on the obtained photocatalytic activity. Especially an imidazole‐functionalized COF displays promising photocatalytic performance due to its high surface area, crystallinity, and wettability. These properties enable it to maintain its photocatalytic activity even in a membrane support. Furthermore, such MCR‐COFs display dramatically enhanced (photo)chemical stability even after long‐term solar light irradiation and exhibit a high and steady H2 evolution for at least 15 days. KW - Sstability KW - Covalent organic frameworks KW - Pore functionality KW - Long-term H2 production KW - Multicomponent reactions PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-639787 DO - https://doi.org/10.1002/aenm.202501193 SN - 1614-6832 SP - 1 EP - 10 PB - Wiley VHC-Verlag AN - OPUS4-63978 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Yildirim, Arda A1 - Haug, T. C. V. A1 - Fröba, M. A1 - Huber, P. A1 - Schönhals, Andreas T1 - Molecular fluctuations in mixed-metal MOF-74: influence of the metal composition N2 - A selected series of metal–organic frameworks M-MOF-74 (M = Mg, Co, Ni) and mixed metal MM-MOF-74 (Mg/Co or Mg/Ni) with different compositions of metal atoms have been prepared and further investigated by broadband dielectric spectroscopy (BDS) in a wide temperature range. The dielectric spectra show at least two relaxation processes. Process-A is observed only for the Ni-containing MOFs and is attributed to localized fluctuations of the metal oxide corners. Relaxation processes-B and -C are observed for all prepared MOFs, except that process-B is not observed for Ni-MOF-74. Large-angle fluctuations such as free rotations of the linkers can be excluded due to the structure of MOF-74, but small-angle fluctuations such as torsions are possible. According to numerical simulations carried out for MOF-74, process-B can be attributed to inward and outward fluctuations of the linkers relative to the pore center. Process-C is related to small-angle rotational fluctuations of the linker together with co-rotations of the metal nodes. The latter interpretation is supported by the dependence of the activation energy of the relaxation rate of process-C on the metal composition of the MOFs, which is discussed in terms of the bond lengths between the metal atoms and the linker which decrease in the sequence Mg, Co and Ni. KW - Metal Organic Frameworks PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-639378 DO - https://doi.org/10.1039/d5ra05357a SN - 2046-2069 VL - 15 IS - 35 SP - 29109 EP - 29118 PB - Royal Society of Chemistry (RSC) AN - OPUS4-63937 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Popiela, Bartosz A1 - Kim, Kyunghwan A1 - Lee, Kyu-Jin A1 - Lee, Jung-Ryul T1 - Impact of internal pressure regulation in filament winding on the quality of composite cylinders: a study with pulse-echo ultrasonic propagation imaging N2 - To ensure the safety of composite pressure vessels considering the growing usage, this case study investigates how wet filament winding parameters affect quality of composite cylinders. Two 6.8-liter Type 4 cylinders with identical geometry and fiber stacking sequence were analyzed using pulse-echo ultrasonic propagation imaging. One cylinder was wound under constant internal pressure, while the other used increasing pressure to influence residual stress and influence imperfections. This difference led to distinct failure mechanisms in burst tests. The study focused on identifying porosity and resin-rich areas, visualized through ultrasonic wave propagation imaging and variable time-window amplitude mapping. Results revealed that the cylinder wound with increasing pressure had better composite consolidation but more resin-rich areas in the hoop windings. The findings demonstrate the effectiveness of pulse-echo ultrasonic imaging as a non-destructive method for detecting manufacturing-induced imperfections and highlight the importance of optimizing filament winding parameters to enhance composite quality. KW - Composite KW - Pressure vessel KW - Wet filament winding KW - Pulse-echo ultrasonic propagation imaging PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-639801 DO - https://doi.org/10.1080/09243046.2025.2547457 SN - 1568-5519 SP - 1 EP - 18 PB - Taylor & Francis AN - OPUS4-63980 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Lozano-Martín, Daniel A1 - Kipphardt, Heinrich A1 - Khanipour, Peyman A1 - Tuma, Dirk A1 - Horrillo, Alfonso A1 - Chamorro, César R. T1 - Impact of hydrogen addition, up to 20 % (mol/mol), on the thermodynamic (p, ρ, T) properties of a reference high-calorific natural gas mixture with significant ethane and propane content N2 - Injecting hydrogen into the natural gas grid supports gradual decarbonization. To check the accuracy of equations of state for hydrogen-enriched natural gas mixtures, precise density data from well-characterized reference mixtures are essential. In a prior study, we provided experimental measurements for a natural gas constituted mainly of methane and for two derived hydrogen-enriched mixtures. In the present study, being the second and final part of our investigation, density measurements for a high-calorific natural gas with significant ethane and propane content, along with two hydrogen-enriched variants (10 and 20 mol-% hydrogen) are provided. The mixtures are gravimetrically prepared following ISO 6142-1. Density measurements, conducted with a single-sinker densimeter at temperatures from (260–350) K and pressures up to 20 MPa, are compared with three equations of state: AGA8-DC92, GERG-2008, and an improved GERG-2008. Results indicate that all models perform better for methane-dominant mixtures than for those containing heavier hydrocarbons. KW - Hydrogen-enriched natural gas KW - High-pressure density KW - Reference equation of state PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-633371 DO - https://doi.org/10.1016/j.ijhydene.2025.05.173 SN - 0360-3199 VL - 140 SP - 256 EP - 271 PB - Elsevier BV CY - Amsterdam AN - OPUS4-63337 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zhuang, Yiling A1 - Haderlein, Stefan B. A1 - Hagemann, Nikolas A1 - Grafmüller, Jannis A1 - Gogler, Karolin A1 - Paul, Andrea A1 - Fink, Friedrich A1 - Spahr, Stephanie T1 - Activation of persulfate by biochar and iron: role of biochar pyrolysis conditions and ash amendments N2 - Redox-active biochars can enhance contaminant transformation in persulfate-based Fenton-like water treatment by facilitating Fe(III) reduction to Fe(II). However, biochar properties vary greatly depending on both feedstock selection and pyrolysis conditions. Best suited biochars for Fe(III) reduction and persulfate activation have yet to be identified. Here, we investigated eight biochars for their ability to activate persulfate with Fe(III) to transform N,N-diethyl-m-toluamide (DEET) in water. Four of the biochars were produced from beech wood under different pyrolysis conditions (450–750 °C, high and low nitrogen flow rate in the reactor) and four biochars were produced from softwood amended with 0 – 43 weight percent (wt%) wood ash prior to pyrolysis at 500 °C. Beech wood biochar produced at 450 °C transformed DEET most efficiently with a half-life time of 39 ± 4 min, likely due to the high concentration of surface oxygen functional groups and persistent free radicals that accelerated Fe(III) reduction and formation of reactive species. Among the ash-amended biochars, biochar with 16 wt% ash amendment showed the most efficient DEET transformation with a half-life time of 27 ± 0.6 min, which is 10-times faster compared to a non-ash-amended biochar produced from the same biomass under similar pyrolysis conditions. Ash amendment led to the formation of crystalline iron minerals in biochars, which likely promoted Fe(III) reduction and persulfate activation. Our results highlight the potential for fine-tuning the redox properties of biochar, e.g., by ash amendment to a woody feedstock, enabling tailored performance for specific water treatment applications. KW - Persistent free radicals KW - Redox-active moieties KW - Fenton-like systems PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-634504 DO - https://doi.org/10.1016/j.seppur.2025.133634 SN - 1383-5866 VL - 374 SP - 1 EP - 8 PB - Elsevier B.V. AN - OPUS4-63450 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Sowoidnich, Kay A1 - Pätzold, Stefan A1 - Ostermann, Markus A1 - Sumpf, Bernd A1 - Maiwald, Martin T1 - Qualitative and quantitative soil characterization on an agricultural field using a portable shifted excitation Raman difference spectroscopy instrument N2 - Site-specific farmland management requires comprehensive information about the soil status to derive informed treatment decisions, e.g. for liming or fertilizer recommendations. Standard laboratory methods relying on sample collection have only limited ability to adequately capture the spatial variability of typical agricultural fields. Here, on-site analytical techniques with the potential to measure the soil properties on a substance-specific level and at the required spatial resolution could be very beneficial. Raman spectroscopy is a very promising technique for this purpose as it provides a molecular fingerprint of soil constituents. However, intrinsic soil fluorescence and daylight interference can be major issues masking characteristic Raman signals. Here, we apply an in-house developed portable shifted excitation Raman difference spectroscopy (SERDS) instrument based on a dual-wavelength diode laser emitting around 785 nm to effectively separate the Raman signals of soil from such interferences. SERDS investigations on a selected agricultural field in Germany demonstrate that the Raman spectroscopic signature of 9 soil minerals and organic carbon could successfully be separated from intense backgrounds. Using partial least squares regression against reference analyses, a successful prediction of the soil carbonate (R2 = 0.86, root mean squared error of cross validation RMSECV = 2.49%) and soil organic carbon content (R2 = 0.89, RMSECV = 0.32%) as important soil parameters is realized. The results obtained on-site with the portable instrument were confirmed by SERDS laboratory experiments of collected soil samples thus highlighting the capability and reliability of portable SERDS as promising and complementary tool for precision agriculture KW - XRF KW - Raman spectroscopy KW - Soil KW - SERDS KW - Precision agriculture PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-634597 DO - https://doi.org/10.1039/d5an00178a SN - 0003-2654 VL - 150 IS - 13 SP - 2934 EP - 2944 PB - Royal Society of Chemistry (RSC) AN - OPUS4-63459 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Golub, Tino Petar A1 - Meyer, Klas A1 - Paul, Andrea A1 - Kipphardt, Heinrich A1 - Tuma, Dirk T1 - Exploring the potential of a setup for combined quantification of hydrogen in natural gas – Raman and NMR spectroscopy N2 - An accurate measurement of the amount fraction of hydrogen in gas mixtures is mandatory for practical applications, requiring methods that are fast, continuous, robust, and cost-effective. This study compares the performance of Raman and benchtop NMR process spectroscopy for determining the hydrogen amount fraction in gas mixtures. A setup was designed to integrate both techniques, enabling measurements of the same sample. Tests were conducted with gravimetrically prepared gas mixtures of reference quality ranging from 1.20 cmol/mol to 85.83 cmol/mol of hydrogen. The results demonstrate that Raman spectroscopy provides superior performance, with a minimal root mean square error (RMSE) of 0.22 cmol/mol and excellent linearity. In contrast, benchtop NMR spectroscopy faced challenges, such as overlapping peaks and longer measurement times, resulting in a higher RMSE of 0.71 cmol/mol. Raman spectroscopy proves to be particularly well-suited for practical applications due to its high accuracy and linearity. Meanwhile, benchtop NMR spectroscopy holds potential for future enhancements through ongoing technological advances, such as higher magnetic field strengths. In summary, the results from our study indicate that Raman spectroscopy is already a serviceable method for precise hydrogen quantification, whereas benchtop NMR spectroscopy can be attributed potential for future applications. KW - Hydrogen amount fraction KW - Raman spectroscopy KW - NMR spectroscopy KW - Field applicability PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-610093 DO - https://doi.org/10.1016/j.saa.2024.125087 SN - 1386-1425 VL - 325 SP - 1 EP - 9 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-61009 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Thiele, Isabel A1 - Weiske, Björn A1 - Riedel, Sebastian L. A1 - Meyer, Klas T1 - On-line monitoring of polyhydroxyalkanoate extraction by low-field nuclear magnetic resonance spectroscopy N2 - The use of low-field nuclear magnetic resonance (NMR) spectroscopy enables real-time reaction monitoring in contrast to time-consuming gas chromatography or off-line high-field NMR measurements. In this study, NMR spectroscopy is demonstrated as a novel process analytical technology (PAT) tool in the downstream processing of polyhydroxyalkanoate (PHA) biopolymers. On-line NMR spectroscopy measurements were performed using a Spinsolve 43 Carbon Ultra instrument in a fully automated mode with a flow-assembly based on PTFE tubing. Single-scan NMR spectra were acquired for real-time monitoring of the extraction process of the PHA copolymer poly(hydroxybutyrate-co-hydroxyhexanoate) with 13.5 mol.% hydroxyhexanoate [P(HB-co-13.5 mol.%HHx)] from Ralstonia eutropha biomass using chloroform or acetone as PHA solvents at lyophilized cell loadings of 20–120 g L􀀀 1. The reproducibility and reliability of low-field NMR spectroscopy was comparable to high-field NMR spectroscopy, with superior performance in terms of time. The correlation between the results of on-line monitoring using low-field NMR spectroscopy and off-line analysis using gas chromatography (GC) showed a correlation coefficient of >94 %. The versatility of low-field NMR spectroscopy for elucidating reaction kinetics, facilitating endpoint determination and accelerating extraction processes by maximizing solubility is highlighted as plateau values were reached within 6–10 min for chloroform and acetone, respectively. This novel low-field NMR spectroscopy application promotes a new monitoring approach for downstream PHA processing and supports process development and optimization. KW - Polyhydroxyalkanoate KW - Extraction KW - NMR KW - Ralstonia eutropha KW - Downstream processing PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-624215 DO - https://doi.org/10.1016/j.polymdegradstab.2025.111188 SN - 1873-2321 VL - 233 SP - 1 EP - 10 PB - Elsevier Ltd. CY - Amsterdam AN - OPUS4-62421 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mervič, Kristina A1 - Azimzada, Agil A1 - Bayat, Mehmet Emin A1 - Šala, Martin A1 - Meermann, Björn T1 - CO2-based matrix-independent carbon quantification approach for single microplastic-ICP-MS analysis N2 - This study presents a new CO2-based, matrix-independent calibration approach for size determination of microplastic (MP) particles using single particle inductively coupled plasma-mass spectrometry (sp-ICP-MS). By incorporating a CO2 gas calibration approach and upon adjusting the flow rates, an accurate size determination of MPs between 2 and 7 μm was enabled. Scanning electron microscopy (SEM) was successfully applied for method validation. The CO2 gas calibration curves exhibited excellent linearity and reproducibility, with minimal matrix effects across different sample types and matrices, including river water and saline solutions. This CO2-based approach eliminates the limitations of matrix- and size-dependent calibrations, enabling robust and accurate size determinations of MPs. This advancement represents a significant step forward in the analytical capabilities for MPs, paving the way for improved environmental monitoring and assessment of plastic pollution. KW - sp-ICP-MS KW - Microplastic KW - New calibration strategy PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-633049 DO - https://doi.org/10.1007/s00216-025-05934-9 SN - 1618-2642 SP - 1 EP - 11 PB - Springer CY - Berlin AN - OPUS4-63304 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - El Moutaouakil, H. A1 - Heimann, Jan A1 - Lozano, Daniel A1 - Memmolo, V. A1 - Schütze, A. T1 - Feature Extractor for Damage Localization on Composite-Overwrapped Pressure Vessel Based on Signal Similarity Using Ultrasonic Guided Waves N2 - Hydrogen is one of the future green energy sources that could resolve issues related to fossil fuels. The widespread use of hydrogen can be enabled by composite-overwrapped pressure vessels for storage. It offers advantages due to its low weight and improved mechanical performance. However, the safe storage of hydrogen requires continuous monitoring. Combining ultrasonic guided waves with interpretable machine learning provides a powerful tool for structural health monitoring. In this study, we developed a feature extraction approach based on a similarity method that enables interpretability in the proposed machine learning model for damage detection and localization in pressure vessels. Furthermore, a systematic optimization was performed to explore and tune the model’s parameters. This resulting model provides accurate damage localization and is capable of detecting and localizing damage on hydrogen pressure vessels with an average localization error of 2 cm and a classification accuracy of 96.5% when using quantized classification. In contrast, binarized classification yields a higher accuracy of 99.5%, but with a larger localization error of 6 cm. KW - Ultrasonic Guided Waves KW - Composite Overwrapped Pressure Vessel KW - Interpretable Machine Learning KW - Structural Health Monitoring KW - Damage Localization KW - Critical Infrastructure KW - Hydrogen KW - Non-destructive Testing PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-640249 DO - https://doi.org/10.3390/app15179288 VL - 15 IS - 17 SP - 1 EP - 20 PB - MDPI AN - OPUS4-64024 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Colombo, Marta A1 - Mostoni, Silvia A1 - Fredi, Giulia A1 - Rodricks, Carol A1 - Kalinka, Gerhard A1 - Riva, Massimiliano A1 - Vassallo, Andrea A1 - Di Credico, Barbara A1 - Scotti, Roberto A1 - Zappalorto, Michele A1 - D'Arienzo, Massimiliano T1 - Interfacial Chemistry Behind Damage Monitoring in Glass Fiber‐Reinforced Composites: Attempts and Perspectives N2 - Glass Fiber Reinforced Polymers (GFRPs) are widely used in structural applications but degrade over time due to internal damage. Structural Health Monitoring (SHM) enables early damage detection, improving reliability and reducing maintenance costs. Traditional SHM methods are often invasive and expensive. An emerging solution involves the embedding of carbon‐based filler like carbon nanotubes and reduced graphene oxide into GFRPs, forming conductive networks that detect damage through resistance changes. However, poor adhesion among GF, filler, and matrix can reduce mechanical performance. Therefore, tailoring GF and filler surface chemistry is essential to enhance durability and enable effective self‐sensing properties. This review summarizes the most recent efforts in modifying GF with carbon‐based filler to design GFRP with improved sensing ability and mechanical performance. After a brief introduction on the role of SHM solutions in early damage detection, an overview of the common GF and filler used in GFRPs will be provided. Then, the most relevant GF modification strategies exploited to incorporate carbon‐based filler in GFRPs will be described, focusing on the chemical grafting approach, which allows a careful optimization of the fiber/matrix interface. Last, a concise summary of the key mechanical and electrical tests to evaluate interfacial adhesion and self‐sensing will be supplied. KW - Review KW - Interface KW - Micromechanics KW - Polymer matrix composites KW - Glass fibre reinforced composites PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-639934 DO - https://doi.org/10.1002/pc.70332 SN - 0272-8397 SP - 1 EP - 30 PB - Wiley AN - OPUS4-63993 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kolmangadi, Mohamed A. A1 - Raab, A. R. A1 - Szymoniak, Paulina A1 - Li, Z. A1 - Huber, P. A1 - Laschat, S. A1 - Schönhals, Andreas T1 - Molecular mobility and electrical conductivity of amino acid-based (DOPA) ionic liquid crystals in the bulk state and nanoconfinement N2 - This study explores the molecular mobility, phase behavior, and electrical conductivity of dihydroxyphenylalanine-based ionic liquid crystals (DOPAn, with alkyl side chains n = 12, 14, 16) featuring cyclic guanidiniumchloride headgroups, in both bulk and nanoconfined states. Using broadband dielectric spectroscopy, differential scanning calorimetry, and fast scanning calorimetry, the research uncovers a complex interplay between molecular structure, self-assembly, and molecular mobility. In bulk, DOPAn shows a phase sequence from plastic crystalline to hexagonal columnar and isotropic phases, driven by superdisc formation and columnar organization. Multiple relaxation processes are identified: localized side-chain dynamics (γ-relaxation), ionic headgroup or core motions (α1-relaxation), and cooperative alkyl domain fluctuations (α2-relaxation). Conductivity decreases with increasing side chain length. Under nanoconfinement in anodic aluminum oxide membranes, phase behavior changes: the Colh–Iso transition is suppressed, and a new α3-relaxation appears, linked to dynamics in an adsorbed interfacial layer. DC conductivity drops by up to four orders of magnitude due to confinement effects, altered molecular orientation, and phase transitions—especially the emergence of a nematic-like state in DOPA16. These findings highlight the importance of molecular design, pore geometry, and surface chemistry in tuning ionic liquid crystal properties for advanced applications in nanofluidics, ion transport, and responsive materials. KW - Ionic Liquid Crystals PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-639657 DO - https://doi.org/10.1039/d5cp02406d SN - 1463-9084 SP - 1 EP - 17 PB - Royal Society of Chemistry (RSC) AN - OPUS4-63965 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Sunder, S. A1 - Jauregui Rozo, Maria A1 - Inasu, S. A1 - Meinel, Dietmar A1 - Schartel, Bernhard A1 - Ruckdäschel, H. T1 - Effect of Ammonium Polyphosphate/Silicate Content on the Postfire Mechanics of Epoxy Glass-Fiber Composites Using Facile Chocolate Bar-Inspired Structures N2 - This study investigates the postfire mechanical properties of epoxy glass-fiber reinforced composites (EP GFRCs) using increasing concentrations of ammonium polyphosphate (APP) and inorganic silicate (InSi) to modify the char and fire residue. A facile chocolate bar-inspired structure was introduced for fire exposure and subsequent flexural testing of the GFRCs. The resin matrix used here was a diglycidyl ether of bisphenol-A (DGEBA) resin, cured with dicyandiamide (DICY), and accelerated by Urone. The microstructures of the degraded composites after three-point bending tests, were evaluated using scanning electron microscopy (SEM) and x-ray computed tomography (XCT) imaging. A previous study showed that increasing the APP and InSi content significantly enhanced flame retardancy, via improved char formation under fire conditions. However, flexural properties and fire resistance were adversely affected after fire exposure, highlighting a trade-off effect. Fiber breakage and delamination of the composites increased upon failure with increasing APP + InSi content in the composite due to unconsolidated char. The experimental values for the postfire flexural mechanics were in good agreement with the two-layer model proposed in literature. This paper presents a preliminary basis for postfire mechanical testing of epoxy composites for use in fire-safe structures, using a combination of standardized testing norms. KW - Flame retardants KW - Post-fire KW - Epoxy KW - Gass fiber composites KW - Prepregs PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-627176 DO - https://doi.org/10.1002/fam.3280 SN - 0308-0501 SN - 1099-1018 VL - 49 IS - 3 SP - 329 EP - 346 PB - Wiley AN - OPUS4-62717 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bibinger, J. A1 - Eibl, S. A1 - Gudladt, H.-J. A1 - Schartel, Bernhard A1 - Höfer, P. T1 - Pushing the limits of thermal resistance in nanocomposites: A comparative study of carbon black and nanotube modifications N2 - Enhancing the thermal resistance of carbon fiber-reinforced polymers (CFRPs) with flame retardants or coatings often leads to increased weight and reduced mechanical integrity. To address these challenges, this study introduces an innovative approach for developing nanocomposites using carbon-based nanoparticles, while preserving the structural lightweight properties. For this, carbon black particles (CBPs) up to 10% and carbon nanotubes (CNTs) up to 1.5% were incorporated into the RTM6/G939 composite material. The obtained samples were then analyzed for their properties and heat resistance under one-sided thermal loading at a heat flux of 50 kW/m2. Results demonstrate that integrating these particles improves heat conduction without compromising the material’s inherent advantages. As a result, thermo-induced damage and the resulting loss of mechanical strength are delayed by 17% with CBPs and 7% with CNTs compared to the unmodified material. Thereby, the thermal behavior can be accurately modeled by a straightforward approach, using calibrated, effective measurements of the nanoparticles in the polymer matrix rather than relying on theoretical assumptions. This approach thus provides a promising methode to characterize and improve thermal resistance without significant trade-offs. KW - Nanomaterial KW - Cabon fiber-reinforced polymer (CFRP) KW - Carbon black (CB) KW - Carbon nanotube (CNT) KW - Improving heat conduction KW - Prediction thermal properties PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-628632 DO - https://doi.org/10.3390/nano15070546 SN - 2079-4991 VL - 15 IS - 7 SP - 1 EP - 23 PB - MDPI CY - Basel AN - OPUS4-62863 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wagner, Jan A1 - Dudziak, Mateusz A1 - Falkenhagen, Jana A1 - Rockel, Daniel A1 - Reimann, H.-A A1 - Schartel, Bernhard T1 - This is the way: An evidence based route to phytic-acid–based flame retardant poly(lactide acid) N2 - A systematic sequence of materials was investigated to develop phytic-acid (Phyt)–based flame retarded poly (lactide acid) (PLA), while factoring in molecular weight (MW), crystallinity and mechanical properties. Synergistic approaches were developed based on combinations with lignin and expandable graphite (EG), as well as by applying different Phyt salts of melamine (Mel), piperazine (Pip), and arginine (Arg). Compounds were twin screw extruded, injection molded, hot pressed and investigated with thermal analysis, size exclusion chromatography, infrared spectroscopy, tensile testing, limited oxygen index (LOI), UL 94, cone calorimeter, and scanning electron microscope. 16.7 wt.% flame retardant (FR) slightly enhances crystallization while MW remains unchanged in PLA Phyt Arg and PLA Phyt Mel. LOI was improved to 43.7 vol.% for PLA Phyt Arg, UL 94 V0 achieved for PLA Phyt Pip. Cone calorimeter results show total heat evolved reduced by 14 %, maximum average rate of heat emission 43 % lower, and peak heat release rate reduced by 50 % for PLA Phyt Mel. Phyt Mel combined with EG increased the char yield of PLA to 20 wt.% and 15.5 wt.% at 600 and 900 ◦C, respectively. Phyt is exploited to enhance char yield, stabilize the intumescent char, and lower the apparent effective heat of combustion. The combination of Phyt Mel and EG was proposed as an efficient FR for PLA via an evidence based developing route. KW - Polylactide acid KW - Intumescent flame retardant KW - Phosphorous flame retardant KW - Phytic acid KW - Expandable graphite KW - Melamine PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-626395 DO - https://doi.org/10.1016/j.polymdegradstab.2025.111242 SN - 1873-2321 SN - 0141-3910 VL - 234 SP - 1 EP - 14 PB - Elsevier Ltd. AN - OPUS4-62639 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Hupp, Vitus A1 - Schartel, Bernhard A1 - Flothmeier, K. A1 - Hartwig, A. T1 - Flame Retarded Adhesive Tapes and Their Influence on the Fire Behavior of Bonded Parts N2 - Pressure-sensitive adhesive tapes are used in automotives, railway vehicles and construction, where flame retardancy is of major importance. This is why industrial applicants often buy, and industrial tape manufacturers often produce, flame-retardant adhesive tapes, advertised for their good flammability characteristics. Yet, how flame-retardant tapes influence the fire behavior of bonded materials is a rather open question. To investigate this issue, three different substrates were bonded, using eight double-sided adhesive tapes containing two different carriers and two different flame retardants. The bonded substrates were compared to their monolithic counterparts in terms of flammability, fire behavior and fire stability. The fire behavior of adhesive tape bonded materials differed significantly from the monolithic substrates. The usage of different adhesive tapes let to different burning behavior of the bonded materials mainly due to different carrier systems. In contrast, the implementation of flame retardant into the adhesive had rather minor or no effect on the burning behavior of the bonded substrates despite their positive effect on the flammability of the free-standing tape. The carrier changed the HRR curve in the cone calorimeter and was able to both, reduce and increase fire hazards. Using the carrier with the better fire performance can lower the fire growth rate by 20%, the peak of heat release rate by 27%, and the maximum average rate of heat emission by 30% in cone calorimeter tests. Overall, the fire behavior of bonded materials is a complex interaction between substrate, adhesive, and carrier, and depends on the fire scenario the materials are exposed to. KW - Pressure-sensitive adhesive tapes KW - Bonded materials KW - Fire behaviour KW - Fire resistance KW - Flame retardant KW - Cone calorimeter PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-626006 DO - https://doi.org/10.1007/s10694-024-01637-2 SN - 1572-8099 SN - 0015-2684 VL - 61 IS - 2 SP - 729 EP - 749 PB - Springer Nature AN - OPUS4-62600 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -