TY - CONF A1 - Priebe, Nsesheye Susan T1 - A modified cementitious system for sub-Saharan Africa N2 - Supplementary cementitious materials (SCMs) are largely used all over the world. The leading SCMs are fly ash (FA) and slag. However, such materials originate from industries that are not well established in sub-Saharan Africa (SSA). Therefore, it becomes extremely challenging and expensive to build up sustainable cement and concrete. For SSA, agriculture is one of the leading economic sectors. Agricultural by-products such as rice husk ash (RHA), can be a potential binder material beneficial for use in a cementitious system. RHA combined with limestone filler (LSF) is an option that can be practised for rice producing countries in Africa. T2 - PhD Day CY - Berlin, Germany DA - 14.07.2015 KW - Supplementary cementitious materials KW - Rice husk as KW - Cement KW - Concrete KW - Sustainable PY - 2015 N1 - Geburtsname von Priebe, Nsesheye Susan: Msinjili, N. S. - Birth name of Priebe, Nsesheye Susan: Msinjili, N. S. AN - OPUS4-41029 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Voigt, Gerrit T1 - Determining moisture in materials and IoT N2 - Knowing the state of the setting process of concrete in buildings or the moisture level of old walls can be crucial in determining further steps in the construction or restoration process. Small 2.4 GHz modules can be either embedded or applied on the surface to determine the moisture distribution in material. Common modules, that are based on the highly available Bluetooth Low Energy standard, emit electromagnetic waves, whose signal strength gets dampened by water molecules. This effect serves as the basis on determining the moisture level in material. We will show how to apply this method in a meshed sensor network for online monitoring. T2 - Fourth Conference on Smart Monitoring, Assessment and Rehabilitation of Civil Structures CY - Zurich, Switzerland DA - 13.09.2017 KW - Moisture KW - Concrete KW - Radio signals KW - Bluetooth PY - 2017 AN - OPUS4-41999 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strangfeld, Christoph T1 - Moisture testing and mapping N2 - Non-destructive testing of moisture in building materials T2 - NDT&E Advanced Training Workshop CY - Berlin, Germany DA - 27.06.2018 KW - Building materials KW - Concrete KW - Moisture measurement PY - 2018 AN - OPUS4-45348 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strangfeld, Christoph T1 - Validierung und Vergleich verschiedener Methoden zur Bestimmung von Flüssigwasser in Baustoffen N2 - Darstellung der aktuellen Feuchtemesstechnik im Bauwesen. Erklärung der Grundlagen über die Sorptionsisotherme und den Wasserdampfpartialdruck. Vorstellung der Ergebnisse der korrespondierenden relativen Luftfeuchtemessungen. T2 - Abteilungsseminar der Abteilung 8, BAM CY - BAM, Berlin, Germany DA - 06.11.2017 KW - Concrete KW - Material moisture KW - Moisture measurements KW - Moisture in civil engineering KW - Corresponding relative humidity PY - 2017 AN - OPUS4-42744 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strangfeld, Christoph T1 - RFID based sensors in civil engineering N2 - Damages in infrastructure due to moisture amount to billions of Euros every year. For a more predictive structural health monitoring in civil engineering, the detection and monitoring of hazardous moisture in steel reinforced concrete constructions is of high interest. The sensors have to be wireless, elsewise they weaken the concrete cover of the rebars. The lifetime of such constructions is normally decades, thus the sensors have to be battery-free and fully passive. Considering these requirements, passive RFID-based sensors are developed. Communication and energy supply are realized wireless via the electromagnetic field of a RFID transmitter. The passive RFID based sensors are embedded into the concrete to enable the monitoring of moisture transport in porous materials. Results of the hydration process are shown. T2 - RFID tomorrow & wireless IoT CY - Düsseldorf, Germany DA - 27.09.2017 KW - RFID based sensors KW - Moisture monitoring KW - Concrete KW - Embedded sensors PY - 2017 AN - OPUS4-42622 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Johann, Sergej T1 - Passive RFID Transponder – Low-Power Multi-Sensor Interface for Structural Health Monitoring in Concrete N2 - Structural Health Monitoring (SHM) has become very important in today's rapidly developing time. High buildings, large bridges and complex technical structures need to be monitored continuously and this over long periods. Visual monitoring cannot evaluate the internal condition of building structures. Thus, material embedded sensors are needed. Cable connection of these sensors pose the disadvantage of weak spots and water intrusion. For concrete embedded sensors the use of batteries is not convenient, because of limited lifetime, difficult charging, and generation of electrical waste.. Hence, monitoring should be implemented preferentially with firmly embedded passive RFID sensor modules. However, since the concrete structure forms an electromagnetically reflective and absorbing barrier, only limited energy can be transmitted to the module. This project requires a highly energy-saving system, which can record different sensor parameters at critical points. T2 - 35th Danubia - Adria Symposium on Advances in Experimental Mechanics CY - Sinaia, Romania DA - 25.09.2018 KW - RFID KW - Structural Health Monitoring KW - Pssive sensorinterface KW - Concrete PY - 2018 AN - OPUS4-46099 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Küttenbaum, Stefan T1 - Reliability assessment of existing bridges based on NDT-results N2 - The non-destructive testing methods available for civil engineering (NDT-CE) enable the measurements of quantitative parameters, which realistically describe the characteristics of existing buildings. In the past, methods for quality evaluation and concepts for validation expanded into NDT-CE to improve the objectivity of measured data. Thereby, a metrological foundation was developed to collect statistically sound and structurally relevant information about the inner construction of structures without destructive interventions. More recently, the demand for recalculations of structural safety was identified. This paper summarizes a basic research study on structural analyses of bridges in combination with NDT. The aim is to use measurement data of nondestructive testing methods as stochastic quantities in static calculations. Therefore, a methodical interface between the guide to the expression of uncertainty in measurement and probabilistic approximation procedures (e.g. FORM) has been proven to be suitable. The motivation is to relate the scientific approach of the structural analysis with real information coming from existing structures and not with those found in the literature. A case study about the probabilistic bending proof of a reinforced concrete bridge with statistically verified data from ultrasonic measurements shows that the measuring results fulfil the requirements concerning precision, trueness, objectivity and reliability. T2 - 5th ICCRRR 2018 - International Conference on Concrete Repair, Rehabilitation and Retrofitting CY - Cape Town, South Africa DA - 19.11.2018 KW - NDT KW - Concrete KW - Stochastic model KW - Reassessment KW - Reliability PY - 2018 AN - OPUS4-46768 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Unger, Jörg F. T1 - A continuum damage model for the simulation of concrete under cyclic loading N2 - Lifetime aspects including fatigue failure of concrete structures were traditionally only of minor importance. Because of the growing interest in maxing out the capacities of concrete, its fatigue failure under compression has become an issue. A variety of interacting phenomena such as e.g. loss of prestress, degradation due to chemical reactions or creep and shrinkage influence the fatigue resistance. Failure due to cyclic loads is generally not instantaneous, but characterized by a steady damage accumulation. Therefore, a reliable numerical model to predict the performance of concrete over its lifetime is required, which accurately captures order effects and full three-dimensional stress states. Many constitutive models for concrete are currently available, which are applicable for specific loading regimes, different time scales and different resolution scales. However, a key limitation of those models is that they generally do not address issues related to fatigue on a structural level. Very few models can be found in the literature that reproduce deterioration of concrete under repeated loading-unloading cycles. This is due to the computational effort necessary to explicitly resolve every cycle which exceeds the currently available computational resources. The limitation can only be overcome by the application of multiscale methods in time. The objective of the paper is the development of numerical methods for the simulation of concrete under fatigue loading using temporal multiscale methods. First, a continuum damage model for concrete is developed with a focus on fatigue under compressive stresses. This includes the possibility to model stress redistributions and capture size effects. In contrast to cycle based approaches, where damage is accumulated based on the number of full stress cycles, a strain based approach is developed that can capture cyclic degradation under variable loading cycles including different amplitudes and loading frequencies. The model is designed to represent failure under static loading as a particular case of fatigue failure after a single loading cycle. As a consequence, most of the material parameters can be deduced from static tests. Only a limit set of additional constitutive parameters is required to accurately describe the evolution under fatigue loading. Another advantage of the proposed model is the possibility to directly incorporate other multi-physics effects such as creep and shrinkage or thermal loading on the constitutive level. Second, a multiscale approach in time is presented to enable structural computations of fatigue failure with a reduced computational effort. The damage rate within the short time scale corresponding to a single cycle is computed based on a Fourier based approach. This evolution equation is then solved on the long time scale using different implicit and explicit time integration schemes. Their performance and some limitations for specific loading regimes is discussed. Finally, the developed methods will be validated and compared to experimental data. T2 - Conference on Computational Modelling of concrete and concrete structures (EURO_C 2018') CY - Bad Hofgastein, Austria DA - 26.02.2018 KW - Fatigue KW - Concrete KW - Damage PY - 2018 AN - OPUS4-48001 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jafari, Abbas T1 - Stochastic parameter estimation of a gradient-enhanced damage material model of concrete using variational Bayesian inference N2 - A gradient-enhanced damage material model for concrete simulated by means of the finite element (FE) method is calibrated with respect to important parameters of the involved constitutive law by using the Variational Bayesian method. T2 - UNCECOMP - 4th International Conference on Uncertainty Quantification in Computational Sciences and Engineering CY - Online meeting DA - 28.06.2021 KW - Stochastic model updating KW - Variational Bayesian KW - Gradient-enhanced damage KW - Concrete PY - 2021 AN - OPUS4-54034 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stohl, Leonie T1 - Bioreceptivity of Concrete Facades N2 - In recent years, the demand for new and sustainable products has been constantly rising. Especially cementitious materials are known for their high carbon footprint and novel approaches will be needed to counterbalance that. The BAM departments 7.1 (building materials) and 4.0 (Material and the environment) try to improve the sustainability of concrete panels by establishing a biofilm on the weather protection layer. Using an ultra-high-performance-concrete allows the production of very thin facade tiles with a small carbon footprint. Furthermore, the durability of these tiles is expected to surpass the one of “normal” concrete facades and offer the possibility of modular renewing of defective tiles instead of a wall, or even remodeling a whole building. The controlled application of biofilms on facades aims to improve biodiversity, microclimate, and air quality in cities. Furthermore, the greening of typically gray surfaces could improve the mental health of the residents. The project focuses on testing a multiplicity of concrete samples, varying e.g., in roughness or pH. The bioreceptivity is analyzed via laboratory tests, as well as in perennial outdoor experiments. T2 - Biology versus building materials: from biocides to bio-receptivity CY - Online meeting DA - 08.02.2022 KW - Bioreceptivity KW - Algea KW - Concrete KW - Biofilm PY - 2022 AN - OPUS4-54470 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -