TY - CONF A1 - Jaunich, Matthias T1 - Low temperature properties of rubber seals N2 - Understanding the failure mechanisms that lead to leakage of rubber seals at low temperatures is important. Rubber properties are highly temperature dependent. Changes in behaviour at low temperatures can result from the rubber-glass transition and for some rubbers by partial crystallisation. Experimental results on the low temperature behaviour of different rubber seals were discussed to help understand seal failure processes. T2 - Rubber in Engineering Group (RIEG) webinar an Elastomers at Low Temperatures CY - Online meeting DA - 11.09.2020 KW - Low temperature KW - Rubber seal KW - Compression set KW - Glass transition PY - 2020 UR - https://www.iom3.org/rubber-engineering-group/event/elastomers-low-temperatures AN - OPUS4-51306 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jaunich, Matthias T1 - Ageing under Hydrogen: effects on O-ring seals N2 - In this work we present results for three typical sealing materials (EPDM, HNBR, FKM) after up to 100 days ageing at high temperature under hydrogen. To allow for a better evaluation of the occurring changes the results are compared with effects of ageing in air on the material properties. Despite the common assumption that ageing under hydrogen atmosphere is expected to be less severe for the material in com-parison to air ageing, this is not seen for every material. T2 - Technomer 2023 CY - Chemnitz, Germany DA - 09.11.2023 KW - Hydrogen KW - Ageing KW - Seal KW - Compression set PY - 2023 AN - OPUS4-58818 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jaunich, Matthias T1 - Investigations of Aged Metal Seals for Interim Storage N2 - The storage of spent fuel and high level radioactive waste in Germany is performed in interim storage containers with double lid systems. The lids are bolted and equipped with metal seals (e.g. Helicoflex®) to ensure the safe enclosure of the inventory. The used metal seals have a layered structure consisting of three components as can be seen schematically in the cross-sectional view in Fig. 1. In the center a helical spring is positioned that is surrounded by two C-shaped jackets and is mainly responsible for generation of the required restoring force. The inner jacket is made of stainless steel and homogenizes the restoring force of the helical spring. The outer jacket is made of silver or aluminium which both are soft metals in comparison to the contact partners (lid and container body). During bolting of the lid to the container body the seal is compressed. The generated restoring force of the helical spring causes a plastic deformation of the outer jacket and adapts to the surfaces of the lid and the container body. Hence, leakage paths are closed and the sealing function is generated. Typical durations for existing interim storage licenses in Germany are 40 years, but it can be expected that they have to be extended to longer periods as a final repository will not be available before the end of the running licence periods. This extension of license periods requires a solid understanding of the long-term behaviour of the seals under storage conditions. To meet this challenge long-term investigations have been started at Bundesanstalt für Materialforschung und –prüfung (BAM) in 2009. These tests focus on seals assembled in test flanges which are stored at temperatures ranging from room temperature to 150 °C for accelerated ageing. The aged seals are tested repeatedly after certain ageing steps and the leakage rate as indicator for sealing performance, the remaining seal force, and the useable resilience upon decompression are determined. In the poster an update on the performed investigations in respect to earlier publications (Grelle et al. 2019, Goral et al. 2023) will be given and the implications of the results for resilient long term safety will be presented. Additionally, a focus will be laid on the currently planned further investigations and the question “What is additionally needed for evaluation of an interim storage period extension in regard to the used metal seals?” will be addressed. T2 - safeND2023: Forschungssymposium des BASE CY - Berlin, Germany DA - 13.09.2023 KW - Metal seal KW - Interim storage KW - Ageing PY - 2023 AN - OPUS4-58568 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jaunich, Matthias T1 - Comparison of Ageing Behavior of O-Ring Seals Under Hydrogen and Air N2 - Elastomeric seals are essential components in the infrastructure which prevent leakage of gas and ensure proper function of technical devices and are therefore highly safety relevant. For proper function a remaining resilience and tolerance to pressure changes is required. The ageing of elastomers is an undesirable but inevitable process leading to a limited lifetime of rubber products such as seals. Independent of the application, as e.g. automotive, piping or container applications, a long lifetime or at least a timely exchange of a seal before occurrence of critical failure is desired. Hydrogen is a key element for the energy turnaround and therefore the compatibility of seals with hydrogen is essential. In addition to the effect of hydrogen uptake and release, which might also cause destructive effects such as rapid gas decompression, ageing at high temperature under hydrogen atmosphere is of interest too. Most of the existing work is addressing the performance of new materials and comprises only very limited investigations concerning long-term use and the behaviour of aged materials in contact with hydrogen. As ageing can lead to substantial changes of material properties, it must be evaluated whether these changes are beneficial or deteriorating for the component function. In this work we present and compare results of the characterization of three sealing materials (EPDM, HNBR, FKM) after ageing at high temperature under hydrogen and air. Despite the common assumption that ageing under hydrogen atmosphere should be less severe for the material in comparison to air ageing, this is not the case for every material. T2 - ASME PVP2025, Pressure Vessels & Piping Conference CY - Montreal, Canada DA - 20.07.2025 KW - Aging KW - Seal KW - Compression set KW - Atomic force microscopy PY - 2025 AN - OPUS4-63888 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jaunich, Matthias T1 - Elastomerdichtungen für Wasserstoffanwendungen - Vergleich des Alterungsverhaltens in Luft und Wasserstoff N2 - In diesem Beitrag soll ein Fokus auf das Alterungsverhalten von Elastomerdichtungen unter Wasserstoff gelegt werden. Hierfür wurden Untersuchungen bei einem mittleren Wasserstoffdruck über Alterungszeiten von bis zu 100 Tagen durchgeführt. Das Alterungsverhalten wird im Vergleich der Alterungseffekte unter thermooxidativen Bedingungen betrachtet und bewertet. Die Annahme, dass der Alterungseffekt unter Wasserstoff stets weniger ausgeprägt ist als an Luft bestätigt sich nicht durch die Ergebnisse. T2 - 4. O-Ring-Forum der Firma ISGATEC CY - Bad Schönborn, Germany DA - 15.05.2025 KW - Wasserstoff KW - Dichtung KW - Thermische Alterung KW - Elastomer PY - 2025 AN - OPUS4-63135 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böttcher, Nils T1 - Lithium und Natrium Ionen Batterien: Eine Frage der Sicherheit - Aktuelle und zukünftige Herausforderungen für die Kreislaufwirtschaft N2 - Der Markt für Energiespeicher befindet sich in einer Phase intensiver technologischer Diversifizierung. Neben etablierten Lithium-Ionen-Batterien gewinnen neue Systeme wie Natrium-Ionen-Batterien und künftige Technologien, z.B. Festkörperbatterien, zunehmend an Bedeutung. Dies stellt neue Anforderungen an Handhabung, Logistik und insbesondere das Recycling respektiver Systeme. Gleichwohl die Batterieverordnung einen künftigen Einsatz von Rezyklat in bei der Herstellung von Batterien vorsieht, ist bislang wenig darüber bekannt, wie sich recycelte Materialien auf Batteriesicherheit-, Leistungsfähigkeit- und Lebensdauer auswirken. Alternativ zu einem direkten Recycling gewinnt ebenso die Verlängerung der Batterielebensdauer durch so genannte „Second-life Anwendungen“ zunehmend an Interesse. Durch verbesserte Methoden zur Vorhersage von Lebensdauer, Restlebensdauer und Betriebssicherheit könnten Batterien länger im Einsatz gehalten werden, was zunehmend Ressourcen schonen würde. Im Rahmen dieses Vortrages werden die o.g. Themen in einem umfassenden Kontext des Gesamtsystems „Batterie“ diskutiert und aktuelle Entwicklungen aus einem regulatorischen und wissenschaftlichen Blickwinkel zusammenfassend dargelegt. T2 - TraWeBa-Kongress CY - Leipzig, Germany DA - 13.05.2025 KW - Recycling von Batterien KW - Thermisches Durchgehen KW - Second-Life Anwendungen KW - Batteriekreisläufe PY - 2025 AN - OPUS4-65076 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Anita T1 - Neuartige Akku‘s/Batterien – Inhaltsstoffe und Reaktionsprodukte N2 - Die Inhaltsstoffe von Batterien sowie die Reaktionsprodukte beim Thermischen Durchgehen werden vorgestellt. T2 - 28. Sitzung der BfR-Kommission „Bewertung von Vergiftungen CY - Berlin, Germany DA - 04.04.2022 KW - Lithiumbatterien KW - Inhaltsstoffe PY - 2022 AN - OPUS4-56755 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberwein, Robert T1 - Systems With Cryogenic Liquefied Gases In Fire-Incidents N2 - The volumetric energy density of a gas can be increased by liquefaction, which occurs when the gas is cooled below the saturation point. Liquefied gases of great importance to the energy transition are Liquefied Hydrogen (LH2) and Liquefied Natural Gas (LNG), which can be liquefied at temperatures below 160°C. Systems for storing these gases typically must be overpressure resistant and require thermal super insulations (TSI) to hold cryogenic conditions and minimize boil-off losses from evaporation. TSI with vacuum and MLI or perlites are suitable for many applications involving LNG and LH2. Such systems are typically double-walled structures where the inner wall is in contact with the cryogenic liquefied gas. MLI or perlites are located in the gap between the inner and the outer wall, that is kept under vacuum conditions. This combination of insulations strongly reduces the heat transfer between the environment and the cryogenic liquefied gas. From an economic point of view the systems are well sophisticated. However, knowledge of the behavior of this kind of systems in a typical event such as a fire is limited, but necessary to evaluate the safety of the increasing number of applications. The objective of the research is to determine how TSI behaves at different fire temperatures during fire exposure and afterwards. Special attention is paid to changes in the heat flux, the material properties and vacuum state over time. For this purpose, thermogravimetric analysis (TGA) studies have been carried out. In addition, a test rig was developed that allows testing of TSI at temperatures up to 1000°C under realistic integration conditions and subsequent analysis of the TSI samples. In the test rig the double-wall with vacuum and MLI or perlites inside is simulated. The fire conditions are simulated on one side of the double-wall by adjustable electrical heating elements. This process allows the implementation of repeatable heat flows of up to 100 kW/m². On the other side of the double-wall, cold or cryogenic conditions are simulated with a heat exchanger through which water or the vapor of liquid nitrogen (approx. -196°C) flows. The heat exchanger is also used to determine the heat flux through the double-wall. Thus, the test rig allows thermal loading and performance analysis of TSI samples at the same time. Compared to tests with real cryogenic systems, tests with this experimental setup have the advantage that, first, the instrumentation is easier to realize, and a higher repeatability is ensured. Second, the local heat flow can be determined over time, and the sample of a TSI can be taken non-destructively and thus analyzed. Third, the tests are less risky as well as time+ and material intensive, so that more tests and variants can be investigated with the same budget. Preliminary results obtained considering several types of MLI under vacuum show that all observed typs of MLI can be damaged under strong thermal loading. The damages observed were outgassing, melting, shrinkage, cracking, lump formation, and concomitant local loss of the MLI's function as a radiation shield. However, the study also shows that a damage does not always have an extreme effect on the insulating performance. T2 - IMECE2022 CY - Columbus, Ohio, USA DA - 30.10.2022 KW - LH2 KW - LNG KW - Safety KW - Insulation KW - Tank PY - 2022 AN - OPUS4-56445 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bock, Robert T1 - Bundesanstalt für Materialforschung und –prüfung - Reallabor Wasserstofftankstelle N2 - Die Bundesanstalt für Materialforschung und -prüfung (BAM) ist eine wissenschaftlich-technische Bundesoberbehörde mit Sitz in Berlin, die zum Geschäftsbereich des Bundesministeriums für Wirtschaft und Klimaschutz gehört. Unsere Hauptaufgabe besteht darin, durch Forschung, Prüfung und Beratung zum Schutz von Mensch, Umwelt und Sachgütern beizutragen. Dies umfasst die Bewertung der Sicherheit von Materialien, Stoffen und Produkten sowie die Entwicklung von Methoden und Standards in Bereichen wie Materialwissenschaft, Werkstofftechnik und Chemie. Wir forschen und prüfen an drei Standorten in Berlin, sowie auf unserem Testgelände Technische Sicherheit in Horstwalde in Brandenburg. Hier haben wir weitreichende Möglichkeiten, Versuche im Realmaßstab durchzuführen. Besonderes Augenmerk möchten wir heute auf das Reallabor Wasserstofftankstelle richten. Diese voll digitalisierte technische Anlage, die die Wertschöpfungskette von Wasserstoff abbildet, wurde gerade eröffnet und steht nun Partnern aus Industrie und Forschung sowie kleinen mittelständischen Unternehmen oder Start-Ups zum gemeinsamen Forschen und Erproben neuer Technologie zur Verfügung. Ihre Besonderheiten umfassen z.B. eine umfassende Prozessüberwachung nach Industrie 4.0, die dafür nötige IT/OT Infrastruktur, Digitale Zwillinge auf verschiedenen Ebenen, großflächige Aufstellung und baulicher Schutz, Gas-Probenahmestellen auf dem Weg durch die Anlage und H2-Sensornetzwerke zur frühzeitigen Erfassung und Ortung von Leckagen. T2 - Wasserstoffforum Lausitz CY - Senftenberg, Germany DA - 03.11.2025 KW - Wasserstoff KW - Reallabor KW - TTS PY - 2025 AN - OPUS4-64697 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Anita T1 - Second life für E-Akkus N2 - Um die Nachhaltigkeit von Lithiumbatterien zu gewährleisten, kommt neben dem Recycling der Rohstoffe auch eine Weiternutzung von für die Erstanwendung nicht mehr ausreichend leistungsstarken Batterien aus der Erstanwendung in Frage. Dabei sind auch Sicherheitsaspekte zu beachten. T2 - Berlin Science Week 2021 CY - Online meeting DA - 10.11.21 KW - Lithium Batterien KW - Recycling KW - Second Life KW - State of Safety PY - 2021 AN - OPUS4-54178 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. A1 - Bock, Robert T1 - Key points in compressed hydrogen storage N2 - This presentation highlights some key points in hydrogen safety related to compressed HYDROGEN STORAGE. It explains some needs concerning the Market ramp-up: cost and safety related aspects like Risk-control by consequence and/or frequency limitation. Other aspects are the optimization of design and test standards by using Monte-Carlo based assessments and the Generation of probabilistic data as input for risk management tools during the design type approval and periodic inspection. Further safety aspects of design and manufacturing have to be taken into account as well as aspects of operational safety with material degradation, non-destructive testing and appropriate tools for operational files. T2 - The opening of BAM hydrogen refueling station CY - Horstwalde, Germany DA - 03.07.2025 KW - Market ramp-up KW - Consequence limitation KW - Frequency limitation KW - Accoustic emission KW - Monte-Carlo PY - 2025 AN - OPUS4-63810 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Anita T1 - Handling and Transport of defective lithiumbatteries N2 - Safe handling and transport of Lithiumbatteries is fundamental for their global trade and use. BAM is the German competent authority responsible for the transport of defective lithium batteries and as such approves transport conditions and packaging for the transport. Also BAM is providing the test protocol for fire testing of packagings. Results and topics around safe transport are described and discussed. T2 - Sino-German Workshop on Dangerous Goods Packaging CY - Online meeting DA - 27.11.2024 KW - Lithium batteries PY - 2024 AN - OPUS4-62330 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Anita T1 - Aktuelle Versuche der BAM N2 - Da die Exkursion zur BAM pandemiebedingt entfallen musste, wurden verschiedene Versuche aus den Bereichen Verpackungen und Lithiumbatterien online vorgestellt T2 - 18. Gefahrgut-Technik-Tage Berlin 2021 CY - Berlin, Germany DA - 18.11.21 KW - Gefahrgutverpackungen KW - Kisten aus Wellpappe KW - Fallprüfung KW - Lithiumbatterien PY - 2021 AN - OPUS4-54179 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tiebe, Carlo T1 - Sensoren und Analytik für Sicherheit und Prozesskontrolle in Wasserstofftechnologien N2 - Der Beitrag beinhaltet Themen vom H2Safety@BAM-Kompetenzfeld Sensorik, Analytik und zertifizierte Referenzmaterialien (SensRef) mit Fokus auf Mess- und Prüfverfahren mit verschiedenen Sensortechnologien und Ultraschallwellen: Metrologie zur Wasserstoffspeicherung - Euramet-Vorhaben "MefHySto", Erkennung von freigesetztem Wasserstoff sowie die Bestimmung des Wasserstoff-Luftverhälntisses mit Gassensoren, zerstörungsfreie Fehlstellenerkennung mit integriertem Zustandsüberwachungssystem basierend auf geführten Ultraschallwellen zur Lebensdauerüberwachung von Composite-Behältern (Wasserstoffspeicher) sowie faseroptische Sensorik zur Schadenfrüherkennung von Wasserstoffspeichern aufgrund erkennbarer Dehnungsänderungen an Druckbehältern. T2 - DVGW Kongress H2 Sicherheit CY - Online meeting DA - 23.11.2022 KW - H2Safety@BAM KW - SensRef KW - Faseroptische Sensorik KW - Gassensorik KW - Geführte Ultraschallwellen KW - Leckdetektion KW - Metrologie zur Wasserstoffspeicherung KW - Zerstörungsfreie Prüfung KW - Structural Health Monitoring (SHM) PY - 2022 AN - OPUS4-56683 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tiebe, Carlo T1 - Prüf- und Messverfahren mit verschiedenen Sensortechnologien und Ultraschallwellen N2 - Der Vortrag zum Mess- und Prüfverfahren mit verschiedenen Sensortechnologien und Ultraschallwellen beinhaltet die Themen: Metrologie zur Wasserstoffspeicherung - Euramet-Vorhaben "MefHySto", Erkennung von freigesetztem Wasserstoff sowie die Bestimmung des Wasserstoff-Luftverhälntisses mit Gassensoren, zerstörungsfreie Fehlstellenerkennung mit integriertem Zustandsüberwachungssystem basierend auf geführten Ultraschallwellen zur Lebensdauerüberwachung von Composite-Behältern (Wasserstoffspeicher) sowie faseroptische Sensorik zur Schadenfrüherkennung von Wasserstoffspeichern aufgrund erkennbarer Dehnungsänderungen an Druckbehältern. T2 - DVGW Kongress H2 Sicherheit CY - Online meeting DA - 28.09.2021 KW - Leckdetektion KW - Metrologie zur Wasserstoffspeicherung KW - Gassensorik KW - Structural Health Monitoring (SHM) KW - Geführte Ultraschallwellen KW - Faseroptische Sensorik KW - Zerstörungsfreie Prüfung PY - 2021 AN - OPUS4-54136 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tiebe, Carlo T1 - Mess- und Prüfverfahren mit Sensorik N2 - Mess- und prüftechnische Verfahren sind zur Prozesskontrolle und Sicherheitsüberwachung in Wasserstofftechnologien von hoher Bedeutung. Typische Anwendungsgebiete von Sensoren sind Sicherheitsüberwachung, Leckdetektion und Prozesskontrolle. In diesem Beitrag werden Themen zur Erkennung von freigesetztem Wasserstoff sowie die Bestimmung des Wasserstoff-Luftverhältnisses mit Gassensoren, Fehlstellenerkennung mit geführten Ultraschallwellen zur Lebensdauerüberwachung (Structural Health Monitoring) von Wasserstoffspeichern sowie der Einsatz faseroptischer Sensoren zur Überwachung des Dehnungs- und Alterungsverhaltens sowie zur Schadensfrüherkennung von Wasserstoffspeichern vorgestellt. T2 - DVGW Kongress H2 Sicherheit CY - Online meeting DA - 27.01.2021 KW - Metrologie KW - Gassensoren KW - Structural Health Monitoring KW - Faseroptische Sensoren KW - Wasserstoff PY - 2021 AN - OPUS4-52141 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. A1 - Bock, Robert T1 - Burst strength and its scatter as key points of safety N2 - Based on the preliminary presentations in this task force it is repeated how a basic population scatters and its degradation influences properties statistically. There is a remainder on the issue of accepting borderline populations due to the minimum burst ratio requirement. Then it is explained in detail how the analysis of minimum requirements by a Monte-Carlo-simulation works. The result with respect to the further reduced minimum burst ratio of 2.0 is summarised and means a two-step approach of two scatter levels requiring two different minimum burst ratios. The methods for evaluating batch tests are analysed. A proposal for integration a statistical analysis is described in detail. Finally, the positive effect of proof testing is shown and its dependence from the real ageing is shown. This ends in the recommendation to have a stronger and quantitative look on real ageing and to follow the 2 proposed sets of criteria for a safe usage of hydrogen storage systems. T2 - 10th IWG on rev GTR 13 CY - Online meeting DA - 28.06.2021 KW - Basic population KW - Minimum burst ratio KW - Monte-Carlo-simulation KW - Borderline population KW - Batch test KW - Proof test KW - Ageing PY - 2021 UR - https://wiki.unece.org/download/attachments/128419731/GTR13-10-08%20BAM%20GTR%2013-2%20scatter%20criteria%20for%20min%20burst%202021-06-25.pdf?api=v2 AN - OPUS4-53149 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holtappels, Kai T1 - Competence Centre H2Safety@BAM - We build trust in hydrogen technologies N2 - Der Beraterkreis Gase wird regelmäßig von der Berufsgenossenschaft Rohstoffe und chemische Industrie, Bereich Prävention, organisiert. Die Veranstaltung dient dem Austausch zwischen Wissenschaft und Wirtschaft zu aktuellen sicherheitstechnischen Fragestellungen rund um Sauerstoff und Wasserstoff. In diesem Zusammenhang hat die BAM einen Überblick über ihre verschiedenen Aktivitäten des Kompetenzzentrums H2Safety@BAM vorgestellt, die sich in der gesamten Wasserstoffwertschöpfungskette wiederfinden. Darüber hinaus wurden die Planungen für den Ausbau der Prüfinfrastruktur auf dem Testgelände Technische Sicherheit der BAM vorgestellt. Es wurden auch die Ergebnisse des Projekts DELFIN zur Sicherheit von Druckgasspeichern, den Freisetzungsuntersuchungen von Flüssigwasserstoff sowie die Unterfeuerung entsprechender Kryospeicher und die Planungen zum Projekt ModuH2Pipe@BAM präsentiert. Den Abschluss bildeten die aktuellen Empfehlungen des Forschungsnetzwerkes Wasserstoff. N2 - The Gases Advisory Group is organized regularly by the Prevention Division of the German Employer's Liability Insurance Association for Raw Materials and the Chemical Industry. The event serves as an exchange between science and industry on current safety-related issues concerning oxygen and hydrogen. In this context, BAM presented an overview of its various activities of the competence center H2Safety@BAM, which are reflected in the entire hydrogen value chain. In addition, the plans for the expansion of the test infrastructure at BAM's Technical Safety Test Site were presented. The results of the DELFIN project on the safety of pressurized gas storage tanks, the release tests of liquid hydrogen as well as the underfiring of corresponding cryogenic storage tanks and the plans for the ModuH2Pipe@BAM project were also presented. The presentation concluded with the current recommendations of the Hydrogen Research Network. T2 - BG RCI Beraterkreis Gase CY - Berlin, Germany DA - 25.04.2023 KW - Berufsgenossenschaft KW - Sicherheit von Wasserstofftechnologien KW - H2Safety@BAM KW - modulare Pipelineanlage PY - 2023 AN - OPUS4-57398 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. A1 - Günzel, Stephan T1 - The maximum acceptable consequence limit as a control instrument N2 - The presentation starts with the first agreement of making a national attempt for the introduction of a pV-limit for hydrogen transport. It explains aspects of the technical development, provides an impression of catastrophic incidents, and explains the difference between risk control and consequence limitation. Then the process of determining consequences and the result from the discussion at the UN-WG are explained. The next part summarises the approach for counting the number of impacted persons as a function of the model of pressure wave, the pressure peak, the limits of injured persons and the population density. Finally, the latest state of the discussion and the subsequent recommendations for a pV-value and the adequate phrases for explanation are introduced. T2 - 29th BAM-DIN-IGV-DVFG-Meeting CY - Online meeting DA - 23.02.2022 KW - Hydrogen KW - Pressure recepacles KW - Consequence limit KW - Risk control KW - Population density KW - Pressure wave PY - 2022 AN - OPUS4-54608 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holtappels, Kai T1 - Education and Training Activities of the Competence Centre H2Safety@BAM N2 - Green hydrogen is seen as a cornerstone of the energy transition and decarbonization efforts of industry, transportation and the utilities sectors. The binding goal of the EU and Germany to reduce net zero carbon emissions by 2045 will substantially increase the demand for green hydrogen as an important carbon-free substitute for fossil fuels. The World Energy Council expects an annual demand of 60 million tons (equivalent 2.000 TWh) hydrogen and its derivatives (especially ammonia and methanol) in the EU until 2050. lt is estimated that the EU can produce less than half of its needed hydrogen by 2050, and will need to import the rest. African coastal countries therefore have the opportunity to become net exporters of their carbon-free regenerative energy in the form of hydrogen and its derivatives and to enable better economic growth and generate wealth on the African continent. The large-scale production, transport and storage of green hydrogen will require large investments in the development of knowledge and training, logistics and capital goods - for both the EU and African countries. BAM is already facing the lack of skilled workers and hydrogen experts. By bundling its expertise in the field of hydrogen technologies into a competence center H2Safety@BAM to create confidence in the technology The topic of hydrogen has been current at BAM for more than one hundred years and is also currently the focus of numerous research and cooperation activities. In order to transfer its expertise in this field BAM developed a number of education activities. The centre of all activities is the Graduate School “Trustworthy Hydrogen”, established in 2022 together with the BTU Cottbus. In the presentation all activities and especially those of the graduate school and details of the cooperation with the University of Namibia are shown. T2 - German-African Green Hydrogen Forum CY - Bernburg (Saale), Germany DA - 23.05.2023 KW - H2Safety@BAM KW - Graduate School KW - Trustworthy Hydrogen KW - Education KW - Skilled workers PY - 2023 AN - OPUS4-57633 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holtappels, Kai T1 - Safety Aspects for Hydrogen Technologies - H2Safety@BAM N2 - Hydrogen is a central component of the energy transition and the European Green Deal for a climate-neutral Europe. To be able to achieve the targets defined by 2045, the EU and the German government have drafted a framework for action and are making long-term investments in research, development and the rapid implementation of innovative hydrogen technologies. The conditions for a successful energy transition and the economic use of green hydrogen as a clean energy carrier are Hydrogen readiness and a rapid market ramp-up, as well as the establishment of the necessary value chains in the national and European framework. Reliable quality and safety standards are the prerequisite for ensuring safety of supply and environmental compatibility and for creating trust in these technologies. BAM has bundled its expertise in the field of hydrogen technologies into a competence center H2Safety@BAM to create confidence in the technology and to support the hydrogen strategies of the German government and the EU. The topic of hydrogen has been current at BAM for more than one hundred years and is also currently the focus of numerous research and cooperation activities. The competence centre H2Safety@BAM and its vision of “We build trust in hydrogen technologies” will be presented with its many safety-related topics, which can be found throughout the entire hydrogen value chain. Two deep dives will present the results on projects dealing with the design-to-cost issue of classical pressurized gas storage containments and the consequences of the release of liquid hydrogen, which will be roughly compared to the release of ammonia. T2 - 25. Kalorimetrietage CY - Braunschweig, Germany DA - 31.05.2023 KW - H2Safety@BAM KW - Safety KW - Hydrogen KW - Gas cylinders KW - DELFIN KW - LH2 KW - Hydrogen release KW - Rapid phase transition KW - Consequences KW - Cyro storage tanks PY - 2023 AN - OPUS4-57629 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Anita T1 - Lithiumbatterien: Anforderungen für die Beförderung von beschädigten Batterien und Überblick über die UN TDG Arbeitsgruppe zur gefahrenbasierten Klassifizierung N2 - Lithiumbatterien: Anforderungen für die Beförderung von beschädigten Batterien und Überblick über die UN TDG Arbeitsgruppe zur gefahrenbasierten Klassifizierung BAM ist beteiligt in den Arbeitsgruppen und stellt eigene Prüfergebnisse vor. T2 - IAA 2022 Transportation, Gefahrguttag des BMDV, "Aktuelle Entwicklungen im Gefahrgutrecht und Erhöhung der Sicherheit von Gefahrgutfahrzeugen" CY - Hannover, Germany DA - 21.09.2022 KW - Lithiumbatterien KW - Energiespeicher KW - UN TDG Lithiumbatterien PY - 2022 AN - OPUS4-56742 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Anita T1 - Herausforderung: Verpackungen von Lithiumbatterien N2 - Je nach Zustand bestehen unterschiedliche Anforderungen an Verpackungen zum Transport von Lithiumbatterien. Hierbei sind bestimmte Prüfungen und Kriterien zu betrachten. Aktuell besteht insbesondere der Bedarf an Verpackungen für kritisch defekte Batterien. Innovative Lösungen sind gefordert. T2 - Workshop AG Future Markets New Energy Packaging CY - Online meeting DA - 12.03.2021 KW - Lithium Batterien KW - Gefahrgutverpackungen PY - 2021 AN - OPUS4-54181 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Winckelmann, Alexander T1 - Investigation of degradation of the aluminum current collector in lithium-ion batteries by glow-discharge optical emission spectroscopy N2 - Lithium-ion batteries (LIBs) are one technology to overcome the challenges of climate and energy crisis. They are widely used in electric vehicles, consumer electronics, or as storage for renewable energy sources. However, despite innovations in batteries' components like cathode and anode materials, separators, and electrolytes, the aging mechanism related to metallic aluminum current collector degradation causes a significant drop in their performance and prevents the durable use of LIBs. Glow-discharge optical emission spectroscopy (GD-OES) is a powerful method for depth-profiling of batteries' electrode materials. This work investigates aging-induced aluminum deposition on commercial lithium cobalt oxide (LCO) batteries' cathodes. The results illustrate the depth-resolved elemental distribution from the cathode surface to the current collector. An accumulation of aluminum is found on the cathode surface by GD-OES, consistent with results from energy-dispersive X-ray spectroscopy (EDX) combined with focused ion beam (FIB) cutting. In comparison to FIB-EDX, GD-OES allows a fast and manageable depth-profiling. Results from different positions on an aged cathode indicate an inhomogeneous aluminum film growth on the surface. The conclusions from these experiments can lead to a better understanding of the degradation of the aluminum current collector, thus leading to higher lifetimes of LIBs. T2 - Adlershofer Forschungsforum 2022 CY - Berlin, Germany DA - 11.11.2022 KW - Lithium Ion Batteries KW - GD-OES KW - FIB KW - SEM KW - EDX PY - 2022 AN - OPUS4-56246 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böttcher, Nils T1 - Sicherheit von Lithium-und Natrium-Batterien - Brandprüfungen und Sicherheitsmaßnahmen N2 - Die Präsentation gibt einen ganzheitlichen Überblick im sicheren Umgang mit elektrochemischen Energiespeichertechnologien. Ferner enthält diese Präsentation einen Überblick über die aktuell an der BAM durchgeführten Forschungsprojekte und hoheitlichen Aufgaben mit Bezug diesen Energiespeichern T2 - Lehrgang "Moderne elektrochemische Energiespeicher" (905350) CY - Mannheim, Germany DA - 16.09.2024 KW - Lithiumbatterien KW - Thermal Runaway KW - Sicherheit KW - Natriumbatterien PY - 2024 AN - OPUS4-62302 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tichter, Tim T1 - Electroanalytical experiments at macroporous electrodes for redox-flow batteries N2 - Macroporous carbon felts (CFs) are the prevalently used electrode material for redox-flow batteris. Owing to their large internal surface area, these structures can efficiently drive the Faradaic reactions in a RFB. However, the electrochemical characterization of novel CFs, or modified CF-materials is a cumbersome task. This is essentially related to the complex mass-transport phenomena which are convoluted with the electrode kinetics. This talk will focus on ex-situ cyclic voltammetry and operando electrochemical impedance spectroscopy as electroanalytical techniques for porous RFB electrodes. Common pitfalls in the voltammetric analysis of CFs are elucidated and recent strategies for modeling and evaluating CV experiments on porous structures are introduced. Finally, a method based on electrochemical impedance spectroscopy is introduced which allows for an operando fingerprinting of electrochemical reactions in a vanadium-based RFB. T2 - Flow4U-Event CY - Eindhoven, Netherlands DA - 08.04.2024 KW - Porous Electrodes KW - Redox-Flow Batteries KW - Digital Simulation KW - Convolutive modeling KW - Impedance Spectroscopy KW - Distribution of Relaxation Times PY - 2024 AN - OPUS4-62304 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tichter, Tim T1 - The DSDC Algorithm - A Universal Strategy for Simulating Voltammetry of Rough and Porous Electrodes N2 - Porous electrodes or electrodes with rough surfaces offer a multitude of tailored applications. The theoretical treatment of such structures is, however, challenging since their voltammetric profile is a convolution of the time-dependent current with an inherently random mass-transfer function. Since the latter quantity has no analytical solution, the classical convolutive techniques cannot be applied. Therefore, simulations have been based on severe simplifications of the diffusion space [1,2] or were performed by means of digital simulation. Unfortunately, the latter approach becomes computationally prohibitive when a large and/or highly resolved, three-dimensional diffusion space needs to be considered. To mitigate these problems, we introduce the digital simulation, deconvolution, convolution (DSDC) algorithm, consisting of four successive steps [3]. Firstly, the three-dimensional image of the electrode under investigation is extracted via micro X-ray computed tomography (µ-CT) or atomic-force microscopy (AFM). Subsequently, the purely mass-transfer controlled current of this spatial template is generated by means of digital simulation. In the third and fourth steps, the mass-transfer function is extracted for a set of discrete points in time by numerical deconvolution and finally used for classical convolutive simulations. In this manner, any simplification of the diffusion domain becomes obsolete and the advantages of digital simulation and convolutive modelling are most favourably combined. Finally, this DSDC-algorithm provides an interdisciplinary connection of ex-situ imaging and in-situ electrochemistry which results in excellent agreement of simulated and experimentally acquired data. T2 - Bunsentagung 2024 CY - Aachen, Germany DA - 25.03.2024 KW - Porous Electrodes KW - Convolutive Modeling KW - Digital Simulation KW - Diffusion KW - Redox-Flow Batteries PY - 2024 AN - OPUS4-62303 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Leonhardt, Robert T1 - Impedance-based characterization of the overstress-related degradationin alkali metal-ion cells N2 - The successful repurposing of degraded alkali metal-ion batteries in second-life applications is a vital step towards achieving a circular economy. While reusing aged cells is a promising way of mitigating their overall environmental footprint, it is crucial to anticipate their future safety and performance characteristics. Unfortunately, predicting these properties is a cumbersome task, essentially caused by limited knowledge of the interference of different degradation modes in the cells’ first life. To still enable estimating of these parameters from a current state, the present study systematically investigates the impact of abusive conditions in an early phase of the cells’ life on their subsequent degradation behavior. For this purpose, individual lithium-ion and sodium-ion cells are initially stressed by different measures such as deep-discharging, high-temperature conditions, and deliberate combinations of the aforementioned methods. Electrochemical performance indicators are monitored during subsequent cycling of the cells, which provides insights into the interdependencies of different degradation modes induced by specific stress conditions. In this manner, it is clarified whether or not the total degradation can be determined by a convolution or a superposition of individual deterioration effects and thus, be described as a multidimensional state function. This knowledge will finally contribute to a better understanding of the performance and safety behavior of degraded batteries which can help to successfully implement them into second-life applications. T2 - Doktorandenseminar der Technischen Universität Berlin CY - Berlin, Germany DA - 30.09.2025 KW - Alkali metal-ion batteries KW - Electrochemical performance indicators PY - 2025 AN - OPUS4-65068 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böttcher, Nils T1 - Lithiumbatterien, Natrium-Ionen Batterien, Festkörperbatterien - Wohin geht die Regelwerksentwicklung? N2 - Der Markt für Energiespeicher befindet sich in einer Phase intensiver technologischer Diversifizierung. Neben etablierten Lithium-Ionen-Batterien gewinnen neue Systeme wie Natrium-Ionen-Batterien und künftige Technologien wie Festkörperbatterien zunehmend an Bedeutung. Dies stellt jedoch neue Anforderungen an die Handhabung und Logistik respektiver Systeme und rückt die Klassifizierung von Batterien nach Gefährlichkeit stärker in den Fokus. In diesem Kontext gilt es Transportprozesse zu vereinfachen und simultan die Sicherheit zu erhöhen. Im Rahmen dieses Vortrags werden aktuelle und kommende Batterietechnologien vorgestellt, die essenziellen Hürden bei deren Handhabung, Transport und Lagerung zusammenfassend dargestellt und ein umfassender Ausblick auf die Regelwerksentwicklung gegeben. Schwerpunkte liegen dabei auf I) der Entwicklung dedizierter Methoden für die Einordnung in Kategorien defekte und kritisch defekte Batteriesysteme, II) Passivierende Verfahren (thermisch und/oder elektrisch) für einen sicheren Transport und III) der Optimierung der Wertschöpfungskette des Gesamtsystems „Batterie“ durch effizientere Batteriekreisläufe und Recyclingverfahren. T2 - Zweite Fachkonferenz Transport und Lagerung von Lithiumbatterien 2025 CY - Augsburg, Germany DA - 03.07.2025 KW - Batteriesicherheit KW - Gekühlter Transport von Batterien KW - Tieftemperaturpassivierung KW - Regelwerksentwicklung KW - Wertschöpfungskette und Batterierecycling PY - 2025 AN - OPUS4-65078 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böttcher, Nils T1 - „Batterien“ Gefahrgutrechtliche Entwicklung für die Anwendung N2 - Der Markt für Energiespeicher bietet eine kontinuierlich wachsende, technologische Vielfalt. Neben etablierten Lithium-Ionen-Batterien gewinnen alternative Systeme wie Natrium-Ionen-Batterien zunehmend an Bedeutung. Jene Entwicklung steigert aktuell die Anforderungen an Regularien für Logistik und Handhabung ebendieser Systeme und bedarf einer dedizierten jedoch gleichwohl praktikablem Klassifizierung unterschiedlicher Batterien nach deren Gefährlichkeit. Genau dies ist der Schwerpunkt der vorliegenden Präsentation. Ein besonderer Fokus liegt dabei auf dem sicheren Transport kritisch defekter Batteriesysteme durch thermische Passivierung und/oder gezieltes Tiefentladen. Explizit werden aktuelle und zukünftige Batterietechnologien vorgestellt, die wesentlichen Herausforderungen bei Handhabung, Transport und Lagerung zusammengefasst und ein umfassender Ausblick auf die Weiterentwicklung der relevanten Regelwerke gegeben. T2 - 35. Münchner Gefahrgut-Tage CY - Munich, Germany DA - 26.05.2025 KW - Batteriesicherheit KW - Thermisches Durchgehen KW - Tieftemperaturpassivierung KW - Initiale Reaktionstemperatur KW - Gekühlter Transport von (kritisch) defekten Batterien PY - 2025 AN - OPUS4-65077 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Morcillo, Dalia T1 - High-resolution absorption isotopic spectrometry as a tool for aging studies of Li-ion batteries N2 - Lithium (Li) is the key element in the manufacturing of batteries. Isotopic study of Li may help to identify the causes of battery aging due to isotopic fractionation during charge/discharge cycles. Isotopic ratio determination is based on monitoring the isotopic components of lithium by their spin-orbit coupling and its isotopic shift of about 15 pm for the 22P←22S electronic transition around 670.788 nm. In this work, we propose improvements to our previous work [1] by using a higher-resolution double echelle modular spectrometer (HR-DEMON II) coupled to a continuum source graphite furnace atomic absorption spectrometer (HR-CS-GF-AAS) for the isotopic analysis of Li. The data analysis was carried out by using a decision-tree-based ensemble machine learning (ML) algorithm (XGBoost). A set of samples with 6Li isotope amount fractions ranging from 0.0004 to 0.99 mol mol-1 was used for the algorithm's training. Subsequently, the procedure was validated by a set of stock chemicals (Li2CO3, LiNO3, LiCl, and LiOH) and a BAM candidate reference material, a cathode material (NMC111). Finally, the ML model was applied to determine the isotope ratio of geological samples, including anorthosite, granite, soil, rhyolite, nepheline syenite, and basalt and battery samples. These samples were measured as digested without any further purification step. Improvements in the optical resolution resolve the lithium isotopic components of the atomic spectra. In the studied geological samples, were found δ7Li values between -0.5 and 4.5 ‰ with a precision range of 1 to 2 ‰. In addition, the proposed method was validated with multi-collector inductively coupled plasma mass spectrometry (MC-ICP-MS), and these results are comparable and compatible. T2 - Caltech-BAM Meeting CY - Online meeting DA - 10.08.2022 KW - Lithium isotope KW - Machine learning KW - Battery KW - High-resolution absorption isotopic spectrometry PY - 2022 AN - OPUS4-56380 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Winckelmann, Alexander T1 - Chemical characterization of aging processes in high energy-density lithium-ion batteries N2 - Introduction Lithium-ion batteries (LIBs) are one key technology to overcome the climate crisis and energy transition challenges. Demands of electric vehicles on higher capacity and power drives research on innovative cathode and anode materials. These high energy-density LIBs are operated at higher voltages, leading to increased electrolyte decay and the current collectors' degradation. Even though this fundamental corrosion process significantly affects battery performance, insufficient research is being done on the aluminum current collector. Fast and convenient analytical methods are needed for monitoring the aging processes in LIBs. Methods In this work glow-discharge optical emission spectrometry (GD-OES) was used for depth profile analysis of aged cathode material. The measurements were performed in pulsed radio frequency mode. Under soft and controlled plasma conditions, high-resolution local determination (in depth) of the elemental composition is possible. Scanning electron microscopy (SEM) combined with a focused ion beam (FIB) cutting and energy dispersive X-ray spectroscopy (EDX) was used to confirm GD-OES results and obtain additional information on elemental distribution. Results The aging of coin cells manufactured with different cathode materials (LCO, LMO, NMC111, NMC424, NMC532, NMC622, and NMC811) was studied. GD-OES depth profiling of new and aged cathode materials was performed. Quantitative analysis was possible through calibration with synthetic standards and correction by sputter rate. Different amounts of aluminum deposit on the cathode surface were found for different materials. The deposit has its origin in the corrosion of the aluminum current collector. The results are compatible with results from FIB-EDX. However, GD-OES is a faster and less laborious analytical method. Therefore, it will accelerate research on corrosion processes in high energy-density batteries. Innovative aspects - Quantitative depth profiling of cathode material -Monitoring of corrosion processes in high energy-density lithium-ion batteries - Systematic investigation of the influence of different cathode materials T2 - ANAKON 2023 CY - Vienna, Austria DA - 11.04.2023 KW - Lithium Ion Batteries KW - GD-OES KW - Depth-profiling PY - 2023 AN - OPUS4-58586 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Winckelmann, Alexander T1 - Investigation of degradation of the aluminum current collector in lithium-ion batteries by glow-discharge optical emission spectroscopy N2 - Lithium-ion batteries (LIBs) are one technology to overcome the challenges of climate and energy crisis. They are widely used in electric vehicles, consumer electronics, or as storage for renewable energy sources. However, despite innovations in batteries' components like cathode and anode materials, separators, and electrolytes, the aging mechanism related to metallic aluminum current collector degradation causes a significant drop in their performance and prevents the durable use of LIBs.[1] Glow-discharge optical emission spectroscopy (GD-OES) is a powerful method for depth-profiling of batteries' electrode materials. This work investigates aging-induced aluminum deposition on commercial lithium cobalt oxide (LCO) batteries' cathodes. The results illustrate the depth-resolved elemental distribution from the cathode surface to the current collector. An accumulation of aluminum is found on the cathode surface by GD-OES, consistent with results from energy-dispersive X-ray spectroscopy (EDX) combined with focused ion beam (FIB) cutting. In comparison to FIB-EDX, GD-OES allows a fast and manageable depth-profiling. Results from different positions on an aged cathode indicate an inhomogeneous aluminum film growth on the surface. The conclusions from these experiments can lead to a better understanding of the degradation of the aluminum current collector, thus leading to higher lifetimes of LIBs. T2 - European Winter Conference on Plasma Spectrochemistry (EWCPS 2023) CY - Ljubljana, Slovenia DA - 29.01.2023 KW - Lithium-ion batteries KW - Aging mechanisms KW - Depth-profiling PY - 2023 AN - OPUS4-56992 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Anita T1 - Role of the Authority in the Approval Process of Packaging N2 - In Germany, BAM is the competent authority in the field of dangerous goods transport. The international dangerous goods transportation rules are presented and their adaptation into German law is described. BAM is responsible for dangerous goods packaging testing, manufacturer surveillance, packaging approvals and inspection of IBC and provides “Gefahrgutregeln” (GGR) to define the processes, e.g. of dangerous goods packagings approvals and surveillance.” T2 - Sino-German Workshop on Dangerous Goods Packaging CY - Online meeting DA - 18.11.2022 KW - Gefahrgutverpackungen KW - Zulassung KW - ADR PY - 2022 AN - OPUS4-56754 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Winckelmann, Alexander T1 - Investigation of degradation of the aluminum current collector in lithium-ion batteries by GD-OES N2 - Lithium-ion batteries (LIBs) are one technology to overcome the challenges of climate and energy crisis. They are widely used in electric vehicles, consumer electronics, or as storage for renewable energy sources. However, despite innovations in batteries' components like cathode and anode materials, separators, and electrolytes, the aging mechanism related to metallic aluminum current collector degradation causes a significant drop in their performance and prevents the durable use of LIBs. Glow-discharge optical emission spectroscopy (GD-OES) is a powerful method for depth-profiling of batteries' electrode materials. This work investigates aging-induced aluminum deposition on commercial lithium cobalt oxide (LCO) batteries' cathodes. The results illustrate the depth-resolved elemental distribution from the cathode surface to the current collector. An accumulation of aluminum is found on the cathode surface by GD-OES, consistent with results from energy-dispersive X-ray spectroscopy (EDX) combined with focused ion beam (FIB) cutting. In comparison to FIB-EDX, GD-OES allows a fast and manageable depth-profiling. Results from different positions on an aged cathode indicate an inhomogeneous aluminum film growth on the surface. The conclusions from these experiments can lead to a better understanding of the degradation of the aluminum current collector, thus leading to higher lifetimes of LIBs. T2 - Empa Group Meeting CY - Dübendorf, Switzerland DA - 22.11.2022 KW - Lithium Ion Batteries KW - GD-OES KW - FIB KW - SEM KW - EDX PY - 2022 AN - OPUS4-56584 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böttcher, Nils T1 - A Journey From Formula Student to Research at BAM N2 - In this presentation, the battery and cell test center of BAM is introduced to the Berlin Motion Lab. Points of intersection are identified, and interested students are familiarized with BAM’s research priorities in the field of batteries. The aim is to foster interaction and to inspire young researchers to engage with technologically relevant topics. T2 - Berlin Deep Tech Nexus Meetup CY - Berlin, Germany DA - 26.02.2025 KW - Battery safety KW - BAM-academy KW - Qualification programme for PhD students at BAM KW - Advanced (battery) safety topics PY - 2025 AN - OPUS4-65079 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. T1 - Welcome to BAM and the Competence Centre H2Safety@BAM N2 - The presentation starts with general slides on BAM, its mission and focus areas. It provides the fields of activity in the focus area “Energy” and explains the structure of the competence Centre and its focus on building trust in hydrogen. The next part shows the H2Safety@BAM’s Products“ in a nutshell and explains the main items with deep dives on the Living Lab “Hydrogen Networks”, the Living Lab „Hydrogen Refuelling Station“, on Reference Materials and Procedures, Storage of Liquid Hydrogen, Storage Systems for Compressed Gases and Material Compatibility. T2 - Information Tour at the Invitation of the Federal Foreign Office The Hydrogen Economy in Germany CY - Berlin, Germany DA - 05.11.2025 KW - Living Lab “Hydrogen Networks” KW - Living Lab „Hydrogen Refueling Station“ KW - Reference Materials and Procedures KW - Storage of Liquid Hydrogen KW - Storage Systems for Compressed Gases KW - Material Compatibility PY - 2025 AN - OPUS4-65101 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sterr, Andrea A1 - Schwarz, Irina T1 - Valorization of Carbon Dioxide by Electrocatalytic Reduction Coupled to Acetogens via Multiple Electron Carriers (Ecat-Acetogens II) N2 - A Bioelectrochemical approach for reducing CO2 to fuels or value-added chemicals allows overcoming the limitations of a pure biochemical or electrochemical approach. A Bioelectrochemical system (BES) for this application has been developed in cooperation with TUM in the first project phase. BAM's contribution to the research focuses on the electrochemical side of the setup, mainly on the development of a suitable CO2RR catalyst for reducing CO2 to CO, which is then consumed by actogenic bacteria to produce further products. Single-metal-atom catalysts in a nitrogen-doped carbon matrix (M-N-Cs) are a promising, sustainable alternative to expensive rare-metal catalysts like Ag and Au. In this work, the first-generation catalyst, a ZIF-8-based Co-N-C is compared to a Mg salt mix templated Ni-N-C. In the new catalysts, the activity for CO2RR as well as the stability during BES operation could be enhanced. T2 - E-Biocat Statusupdate 2025 CY - Karlsruhe, Germany DA - 01.04.2025 KW - CO2RR KW - M-N-Cs KW - Bioelectrochemical System PY - 2025 AN - OPUS4-65143 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. T1 - DE-JP Hydrogen Safety Cooperation - Contribution of H2Safety@BAM N2 - The presentation starts with general slides on BAM, its location, mission, tasks and focus areas. It provides the fields of activity in the focus area “Energy” and explains the structure of the competence Centre and its focus on building trust in hydrogen. The test sides at TTS on hydrogen are explained in combination with the H2Safety@BAM’s products in a nutshell. Then the major H2-applications of H2Safety@BAM are explained by deep dives on the Living Lab “Hydrogen Networks”, the Living Lab „Hydrogen Refuelling Station“, on Explosion Protection, on Reference Materials and Procedures, on Material Compatibility, on Storage Systems for Compressed Gases and Storage of Liquid Hydrogen as well as on the Training and Further Education. The presentation ends with an overview about our international work on H2Safe-Collaboration. T2 - KICK-OFF WORKSHOP: JAPANESE-GERMAN COOPERATION ON H2 SAFETY CY - Online meeting DA - 15.12.2025 KW - Living Lab KW - Hydrogen Networks KW - Hydrogen Refuelling Station KW - Explosion Protection KW - Material Compatibility KW - Liquid Hydrogen KW - Compressed Gases PY - 2025 AN - OPUS4-65151 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ghaznavi, Ali T1 - Machine Learning Approach for Robust Acoustic Emission-Based Damage Classification in Pressure Vessels N2 - Accurate damage classification of Composite Pressure Vessels (CPVs) is crucial for understanding failure behaviour of hydrogen storage systems. Acoustic Emission (AE) monitoring is a non-destructive testing technique capable of detecting signals from different failure mechanisms such as fiber breakage and matrix cracking, supporting durability assessment of CPVs. Therefore, the main objective of this study is to combine AE and advanced deep learning techniques to develop a robust framework for automatic and accurate identification and classification of damage mechanisms across various CPVs. The evolutionary Genetic Algorithms (GA) was used for feature selection, followed by unsupervised clustering to generate automatic labels for model training. Two different FCNN and CNN-LSTM architectures were used to train individual models based on different AE datasets. Later, Adaptive Transfer Learning (ATL) and Meta Ensemble Learning (MEL) techniques were applied to handle data variability and train predictive generalized model over varied AE datasets. The ATL fine-tunes a pre-trained models to leverage their knowledge, while MEL uses pre-trained models' predictions as meta features to train a meta model. Experimental results demonstrate that while both generalized ATL and MEL trained models perform well across different AE datasets, the MEL framework outperforms ATL method in terms of evaluation metrics. The Mean-Accuracy score reaches 0.9026, and 0.9900 for ATL, and MEL, respectively. The most accurate multi-class classification results was achieved using MEL method in terms of the Mean-Accuracy and Recall metrics. The proposed framework provides a scalable, adaptive approach for automated damage classification using AE signals across diverse CPVs in real-world settings. T2 - BAM Colloquium Abteilung 3 CY - Berlin, Germany DA - 14.10.2025 KW - Acoustic Emission KW - Machine Learning KW - Sequential Neural Network KW - Deep Learning KW - Deep Neural Network PY - 2025 AN - OPUS4-65184 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bock, Robert A1 - Mair, Georg W. A1 - Tiebe, Carlo A1 - Melzer, Michael A1 - Klaus, Christian A1 - Nattuveettil, Keerthana A1 - Engel, Thomas A1 - Prager, Jens T1 - Eine digitale QI für technische Anlagen: Beispiel Wasserstofftankstelle (H2) N2 - Mit der Initiative QI-Digital werden völlig neue Perspektiven für das Sicherheitsmanagement und die Qualitätssicherung technischer Anlagen erschaffen. Unsere Forschung im Kontext einer Wasserstofftankstelle zeigt, wie digitale Innovationen und Verfahren die Herausforderungen effizienter und verlässlicher Qualitätssicherung für komplexe Anlagen bewältigen können. In diesem Vortrag werden Potentiale und Beispiele der digitalen QI für technische Anlagen demonstriert und diskutiert: Moderne Anlagenüberwachung mit digitalen Zwillingen und KI sowie Kalibriermanagement mithilfe digitaler Kalibrierscheine und elektronischem Siegel. T2 - 2. QI Digital Forum CY - Berlin, Germany DA - 10.10.2023 KW - Wasserstoff KW - Sensorik KW - Qualitätsinfrastruktur KW - Digitalisierung KW - Druckspeicher KW - Verwaltungsschale PY - 2023 AN - OPUS4-58599 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bock, Robert T1 - Pilotprojekt Wasserstofftankstelle - Session 2: Verlässliche Wassertofftankstellen N2 - Was ist QI? Qualitätsinfrastruktur – Das Zusammenwirken von nationalen Institutionen im Bereich der Metrologie, Normung und Standardisierung, Akkreditierung, Konformitätsbewertung und Marktüberwachung, mit dem Ziel die Qualitätssicherung bei Produkten und Prozessen in Deutschland zu gewährleisten. Unser Ziel ist es, unsere bewährte Qualitätsinfrastruktur (QI) noch besser zu machen und so einen Beitrag zur Lösung von sozioökonomischen, ökologischen und technologischen Herausforderungen unserer Zeit zu leisten. Eine der bedeutendsten technologischen Herausforderungen unserer Zeit ist die Digitalisierung. Die zentralen Akteure der deutschen QI wollen diese digitalisieren. Beteiligte Institutionen sind aktuell BAM (Konformitätsbewertungen in bestimmten Bereichen), DAKKS (Akkreditierung), DIN/DKE (Normung), PTB (Metrologie). Wir wollen also ein Reallabor errichten, das die Wertschöpfungskette einer Tankstelle abbildet, also eine Wasserstofftankstelle beinhaltet, die dann mit erweiterter Sensorik ausgestattet werden soll. Somit sollen digitale Prozesse abgebildet werden können sowie sensorgestützte Verfahren zur qualitätsgesicherten Datenerfassung und -auswertung genutzt werden. Diese gesammelten Daten sollen dann in eine Dateninfrastruktur eingehen und mithilfe eines Datenmanagementsystems sowie künstlicher Intelligenz in einem Digitalen Zwilling zusammenlaufen, der die digitale Prozessüberwachung der Sicherheit möglich macht. Schließlich sollen die in QI Digital entwickelten digitalen Strukturelemente der QI erprobt werden, insbesondere die QI Cloud, Smart Standards und digitalen Zertifikate. Im Zusammenspiel ermöglicht das unter anderem die Entwicklung von Predictive Maintenance Verfahren für: 1. die Optimierung von Wartungszyklen und Minimierung von Ausfallzeiten Erhöhung der Betriebssicherheit durch frühzeitige Identifikation kritischer Zustände im Gesamtsystem 2. Entwicklung verlässlicher Qualitäts- und Sicherheitsstandards  3. Digital-gestützte Risikobeurteilung und Konformitätsbewertung Die im Pilotprojekte betrachteten Sicherheitsaspekte sind also zusammenfassbar als: a) Auswirkungsbetrachtungen bei möglichen Fehlfunktionen oder Defekten b) Die genannte vorrauschauende Instandhaltung und damit verbundene Lebensdauerprognose, die in Kombination eine bessere allgemeine Verfügbarkeit garantieren sollen Als Grundlage hierfür benötigen wir aber Änderungen im Bereich der technischen Regeln und Normen, um die neuen digitalen Werkzeuge zuzulassen und nutzbar zu machen. T2 - QI Forum 2022 CY - Berlin, Germany DA - 11.10.2022 KW - Wasserstoff KW - Qualitätsinfrastruktur KW - Digitalisierung PY - 2022 AN - OPUS4-61356 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Orellana Pérez, Teresa T1 - QI Digital Use Case Hydrogen Refueling Station N2 - BAM is part of the “Quality Infrastructure Digital” (QI Digital) initiative of the German Federal Ministry for Economic Affairs and Climate Action (BMWK). This initiative aims at coordinating a large cooperation project, “QI Digital” for making German and European quality management systems fit for the digital transformation. It is a fact that the digitization of new products and services is occurring much faster than quality management systems can be accordingly updated. Thus, the digital transformation of quality management is necessary to preserve the competitiveness of the German and European industries that stand for quality and safety in the global market. The Use Case “Reliable Hydrogen Refueling Station” of QI Digital aims at creating new solutions that are transferable to other technical systems and at further developing standards and technical rules as a contribution to technology transfer and innovation. T2 - 4th German-Korean Hydrogen Conference CY - Seoul, Republic of Korea DA - 31.10.2023 KW - Hydrogen refueling station KW - Digital quality infrastructure PY - 2023 AN - OPUS4-59303 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bock, Robert A1 - Mair, Georg W. T1 - Pilotprojekt "Verlässliche Wasserstofftechnologie" - Beispielanwendung für eine technische Anlage N2 - Kurzvorstellung des Pilotprojektes Verlässliche Wasserstofftechnologie in QI Digital. Anwendung der QI Digital Werkzeuge an einer technischen Anlage beispielhaft gezeigt anhand von sechs im Projekt entwickelten Demonstratoren. Unser erklärtes Ziel ist die Unterstützung des Markthochlaufs von Wasserstofftechnologien durch Digitalisierung der QI. Bei der Qualitätsinfrastruktur von technischen Anlagen geht es vor allem die Themen QI Dokumentation und Zugänglichkeit, Verfügbarkeit der Anlage und Informationen darüber, sowie Inspektionszyklen mit zeitaufwändigen und teuren manuellen Prüfungen. Mit dem Übergang zu einer digitalen QI streben wir hier an, eine kontinuierliche Überwachung des momentanen Gesundheitszustandes der Anlage und automatisierter Dokumentation hierüber, die fälschungssicher und vertraulich zugänglich gemacht werden kann, zu erreichen. Hierzu sollen die im Gesamtprojekt entwickelten QI Digital Werkzeuge zum Einsatz kommen. T2 - QI Forum 2024 CY - Berlin, Germany DA - 09.10.2024 KW - Wasserstoff KW - Qualitätsinfrastruktur KW - Digitalisierung PY - 2024 AN - OPUS4-61354 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kehr, Torsten T1 - Project QI-Digital - Quo vadis Use Case H2 Refueling Station? N2 - As a part of the QI-Digital cooperation project, BAM is setting up a hydrogen refuelling station research platform at the Test site for Technical Safety in Horstwalde. Based on this platform, BAM intends to develop, to test and to optimize new measurement techniques as well as data acquisition and processing methods for hydrogen refuelling stations and their periphery in close cooperation with partners from the quality infrastructure and industry. The presentation will introduce the hydrogen refuelling station use case and provide insights into the issues and research goals of the associated subprojects. T2 - H2-Colloquium of the Competence Centre „H2SAFETY@BAM” CY - Online meeting DA - 16.02.2022 KW - Hydrogen KW - Safety KW - QI-Digital PY - 2022 AN - OPUS4-54361 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. T1 - Aspekte einer digitalen Lebenslaufakte (Impulsvortrag) N2 - Durch Einsatz neuer Technologien im Transport von komprimiertem Wasserstoff konnte eine Verdreifachung des Nutzlastverhältnisses erreicht werden. Diese neuen Speicher auf den Transportfahrzeugen müssten aber anders auf ihre Sicherheit überprüft werden, als dies heute gefordert wird. Mit dem Markthochlauf Wasserstoff vervielfacht sich zudem die Anzahl der Transporteinheiten. Da sich im Zuge der neuen H2-Transportfahrzeuge aber auch die Anzahl der einzelnen Speicher pro Fahrzeug etwa verzwanzigfacht hat, kommen die Kapazitäten für die erforderliche wiederkehrende Prüfung an ihre Grenzen. Dies könnte evtl. durch eine entsprechende Erhöhung der Prüfkapazitäten gelöst werden. Da dies aber weder praktisch machbar ist noch technisch wirklich sinnvoll, müssen alternative Ansätze z.B. durch digital erfasste zerstörungsfreie Prüfkonzepte gesucht werden. Hierzu bedarf es aber einer Lebenslaufakte, die beginnend von der Definition einer Bauweise über die Baumusterprüfung, Zulassung, Herstellung, erstmalige Prüfung, Verwendung und wiederkehrenden oder begleitenden Prüfungen bis zum Verschrotten alle Daten erfassen und verwalten kann. Eine solche Lebenslaufakte könnte auch als eine Art digitaler Produktpass (DPP) verstanden werden. T2 - QI-digital Forum 2023 CY - Berlin, Germany DA - 10.10.2023 KW - Wasserstoffspeicher KW - Lebenslaufakte KW - Digitaler Produktpass DPP KW - Wiederkehrende Prüfung KW - Lebensdauerüberwachung PY - 2023 AN - OPUS4-58559 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scarponi, Giordano T1 - Numerical Simulation Of Cryogenic Liquid Hydrogen Tanks With Multilayer Insulation Exposed to Fire N2 - In the ongoing energy transition, hydrogen has emerged as a promising alternative energy carrier with a reduced environmental impact. Among the possible solutions to store hydrogen onboard vehicles, cryogenic tanks equipped with multilayer insulation (MLI) appear to be one of the most effective in ensuring high volumetric energy density. MLI systems consist of several layers of low-emissivity material (radiative layers), typically aluminum or aluminum-coated polyester, interleaved with low thermal conductivity spacers to avoid direct contact between the radiative layers. In cryogenic tank applications, these are enclosed within the vessel double-walled shell, working under high-vacuum conditions. Among the insulation systems available nowadays, MLI-based ones have the smallest volume requirements and the lowest weight. Thanks to these features, MLI appears as the preferable choice in sectors where space and weight constraints play a crucial role (e.g., in the transportation sector). The widespread deployment of LH2 new technologies poses also challenging questions related to the hazardous properties of hydrogen. The accidental loss of integrity of cryogenic LH2 tanks might lead to extremely dangerous phenomena, such as Boiling Liquid Expanding Vapour Explosions (BLEVE), Fireball, and Rapid Phase Transition (RPT). One potential scenario that could give rise to this situation is exposure to an external heat source such as a fire triggered by a road accident. Real-scale fire test results suggest that the insulation performance of MLI systems may undergo severe degradation when these are subjected to high temperatures, leaving the tank almost unprotected and leading to failure in a relatively short time. In this framework, the availability of models able to simulate the tank response to fire exposure is crucial to ensure a safe design and support emergency response planning. Several CFD and lumped models originally developed for pressurized and atmospheric tanks were extended to cryogenic vessels. However, these provide results in line with experimental data only if the insulation system's equivalent thermal conductivity is fine-adjusted to higher values with respect to normal operating conditions. These models do not integrate, in fact, the description of MLI thermal degradation as a result of fire exposure, which was demonstrated to play a crucial role in determining the response of the cryogenic liquid hydrogen tank. On the other hand, MLI heat transfer models currently available in the literature are suitable for normal operative conditions only and do not address the material behavior under fire exposure. This work presents an innovative lumped model to simulate the thermal response of MLI-insulated cryogenic hydrogen tanks in fire scenarios. In particular, the proposed approach enables the prediction of MLI loss of insulation performances due to fire-induced thermal degradation, overcoming the limitations of currently available models. The MLI degradation model is based on the well-established layer-by-layer approach and integrated with sub-models to estimate the material deterioration due to thermal load. Several sub-models were defined to account for different MLI materials. In particular, for polyester-based MLIs, the deterioration of each layer is defined by the apparent kinetic of thermal degradation retrieved from Thermo-Gravimetric-Analysis (TGA) tests. For aluminum-based MLI, each radiation layer is assumed to vanish when its temperature reaches the melting point of the material. The model was applied to several case studies addressing different types of MLI (i.e., both polyester-based and aluminum-based ones) and fire scenarios to assess the effect on the heating rate and pressure build-up of the tank lading. The analysis allowed for the performance comparison of the studied MLIs, providing valuable information to support the emergency management of accidental scenarios involving liquid-hydrogen cryogenic tanks. Moreover, the results obtained can be used to define mitigation measures to protect the integrity of cryogenic tanks equipped with MLI. T2 - Spring24+20thGCPS CY - New Orleans, Louisiana, USA DA - 24.03.2024 KW - Multilayer Insulation KW - Fire KW - Hydrogen KW - Liquefied Natural Gas KW - Insulation PY - 2024 AN - OPUS4-61078 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. T1 - Risk management and consequence control in hydrogen transport - volume dependent pressure limitation as a scientific approach for consequence control N2 - With technological development, the transport units for compressed gases are becoming larger and their number is increasing. Simultaneously, the filling pressure for hydrogen in transport has increased far beyond the 200 bar, which has been the common European standard for decades. In total, this increases the potential consequences of an incident, which needs to get limited for ensuring acceptance in current practice with pressure vessels from large serial production. Consequently, the measures for new developments of extremely large and highly pressurised pressure vessels should meet a risk based higher level of requirements. For this purpose, the so-called pressure-volume product was proposed as a safety related criteria to the relevant regulatory bodies in 2020. The approach was accepted, and a working group was set up at the United Nations for developing a broadly accepted limitation of today's established pressure vessels compared to future units with even more gas content. The path to the finally decided limit value of 1.5 million bar litres is presented here for hydrogen with its individual steps: ‘Boundary between major accident and disaster’, ‘The effect of pressure waves on the human body’, ‘The propagation of pressure waves’, ‘The reference value for population density’ and ‘Impact of pressure waves’. This result of the UN working group has been accepted in December 2023 and will lead to a binding limitation of the pressure volume product for the so called pressure receptacles by 2027. The work on units larger than this pV-limit is going on at ISO level. T2 - 11th International Conference on Hydrogen Safety ICHS 2025 CY - Seoul, South Korea DA - 22.09.2025 KW - Safety KW - Hydrogen transport KW - Major accident KW - Pressure wave KW - Population density KW - Science with impact PY - 2025 AN - OPUS4-64198 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Anita T1 - Forschung der BAM zu Lithiumbatterien: Schwerpunkt Anwendungsebene N2 - Für den Transport von Lithiumbatterien als Gefahrgut sind Kenntnisse über deren Verhalten und möglichen Schutz in Form von Verpackungen essentiell. Die aktuellen Forschungsergebnisse der BAM der letzten 2 Jahre werden dem Fachpublikum vorgestellt. T2 - BAM Erfa Verpackungen CY - Berlin, Germany DA - 17.09.2024 KW - Lithiumbatterien KW - Gefahrguttransport KW - Gefahrverpackungen PY - 2024 AN - OPUS4-62332 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Camplese, Davide T1 - Safety assessment of MLI super-insulation systems for cryogenic liquid-hydrogen tanks in fire scenarios N2 - In the context of green energy transition, cryogenic tanks featuring MLI systems are emerging as a leading solution to store hydrogen in heavy-duty vehicles. However, the integrity of such tanks can be jeopardized by fire. In such a scenario, MLI materials degradation can occur, leaving the tank unprotected from the fire heat flux, with consequent rapid pressurization and a high risk of failure. This study presents an assessment of aluminum-based MLI for liquid hydrogen cryogenic tanks under fire exposure based on the estimation of the time to mechanical failure of the equipment. This is calculated through an innovative model that simulates the thermomechanical response of the tank, including the MLI thermal degradation and the pressure-relief valve (PRV) operation. The application to several case studies that consider a typical LH2 tank featuring a wide range of MLI configurations demonstrated the likelihood of failure in case of exposure to a hydrocarbon pool fire, providing also comprehensive insights into the impact of the insulation characteristics and operating conditions on the time to failure. T2 - 18th EFCE International Symposium on Loss Prevention and Safety Promotion in the Process Industries CY - Bologna, Italy DA - 08.06.2025 KW - LH2 KW - Insulation KW - Tanks KW - Fire KW - LNG PY - 2025 AN - OPUS4-63427 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -