TY - CONF A1 - Thiel, Erik T1 - AM activities at BAM with focus on process monitoring N2 - The presentation gives an overview of current projects in additive manufacturing at BAM. In particular, the results of the ProMoAm project were presented. T2 - VAMAS - Materials Issues in Additive Manufacturing CY - Berlin, Germany DA - 25.06.2018 KW - Additive Manufacturing KW - Laser Metal Deposition KW - Thermography KW - Data Fusion KW - In-situ monitoring PY - 2018 AN - OPUS4-45620 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Widjaja, Martinus Putra T1 - Accumulation of fibre breaks in racetrack specimens and type IV pressure vessels N2 - The reduced volume method has been studied using the fibre break model from Mines ParisTech. This method allows less 3D finite elements to be used for predicting the failure of real scale composite structures. A favourable comparison results with racetrack specimens has been achieved. However, the comparison study with a type IV pressure vessels still requires more Evaluation. T2 - Consortium Meeting FiBreMoD CY - Toyota Motor Europe, Belgium DA - 27.03.2019 KW - Reduced volume method KW - Integral range KW - Multiscale model KW - Fibre break KW - Composite pressure vessels KW - Racetrack specimens PY - 2019 AN - OPUS4-48571 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Evans, Alexander T1 - Residual stresses Analysis in Additively Manufactured alloys using neutron diffraction (L-PBF) N2 - An overview of recent progress at BAM of residual stress analysis in additively manufactured, in particular Laser Powder Bed Fusion of metallics materials, using neutron diffraction will be presented. This will cover important topics of the stress-free reference, the diffraction elastic moduli and principal stress determination. T2 - AWT-Fachausschuss 13 "Eigenspannungen" CY - Berlin, Germany DA - 28.03.2023 KW - AGIL KW - Residual stress KW - Additive manufacturing KW - Laser Powder Bed Fusion KW - Diffraction PY - 2023 AN - OPUS4-59177 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bruno, Giovanni T1 - The combined use of X-ray refraction and trans-mission radiography and computed tomography N2 - Alternative to conventional transmission-based radiography and computed tomography, X-ray refraction techniques are being increasingly used to detect damage in light materials. In fact, their range of application has been recently extended even to metals. The big advantage of X-ray refraction techniques is that they are able to detect nanometric defects, whose size would lie below the resolution of even state-of-the-art synchrotron-based X-ray computed tomography (SXCT). The superiority of synchrotron X-ray refraction radiography and tomography (SXRR and SXRCT) has been shown in the case of light materials, in particular composites. X-ray refraction techniques also yield a quantitifaction of the amount of damage (the so-called relative internal specific surface) and can well be compared with damage models. At the same time, it is impossible for SXRR and SXRCT to image single defects. We show that the combination of refraction- and transmission-based imaging techniques yields an impressive amount of additional information about the type and amount of defects in microstructured materials such as additively manufactured metals or metal matrix composites. We also show that the use of data fusion techniques allows the classification of defects in statistically significant representative volume elements. T2 - 11th Conference on Industrial Computed Tomography CY - Online meeting DA - 08.02.2022 KW - X-ray refraction radiography KW - Computed Tomography KW - Synchrotron radiation KW - Additive manufacturing KW - Damage evolution PY - 2022 AN - OPUS4-54327 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bresch, Sophie T1 - Optimization of Solid-State-Reactions of Calcium Cobaltite Ca3Co4O9 N2 - Calcium cobaltite is a promising p-type oxide thermoelectric material for high temperature applications due to its high figure of merit between 600 °C and 900 °C in air. The solid-state-reaction is well known for large scale powder synthesis of functional materials. As a high temperature process, the powder synthesis consumes a lot of energy. In different studies, different synthesis conditions were used for the preparation of calcium cobaltite powder. This study showed that a higher energy input (elevated temperatures, longer dwell times, or repeated calcinations) during powder synthesis does not increase but decrease the Seebeck coefficient and the electrical conductivity. The same correlation was determined for the densification. As a higher energy input leads to a larger grain size and therefore to a reduced sinter activity, it can be concluded that the thermoelectric properties are correlated with the sinter activity of the powder. These results can be used to minimize the energy demand for the powder synthesis of Ca₃Co₄ O₉. T2 - 14th European Conference on Thermoelectrics CY - Lisbon, Portugal DA - 20.09.2016 KW - Thermoelectrics KW - Solid-State-Reaction KW - Calcium cobaltite PY - 2016 AN - OPUS4-37543 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mieller, Björn T1 - Surface Characteristics of LTCC-.Substrates Fabricated by Pressure-Assisted Sintering T2 - IMAPS/ACerS 9th Int. Conf. and Exhib. on Ceramic Interconnect and Ceramic Microsystems Technolgies (CICMT 2013) CY - Orlando, FL, USA DA - 2013-04-23 PY - 2013 N1 - Geburtsname von Mieller, Björn: Brandt, B. - Birth name of Mieller, Björn: Brandt, B. AN - OPUS4-28292 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Bernd R. T1 - Röntgen-Refraktions-Technik für eine schnelle, hochauflösende Mikrostrukturcharakterisierung von Leichtbaukompositen T2 - Verbundwerkstoffe und Werkstoffverbunde 2015 CY - Wien, Austria DA - 2015-07-01 PY - 2015 AN - OPUS4-33684 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Evans, Alexander T1 - Diffraction based residual stress analysis: challenges and opportunities in additive manufacturing N2 - This presentation overviews the challanges and opportunities of diffraction based residual stress analysis for additively manufactured metals. Through examples, the challanges and respective solutions are presented and the opportunities that the presented methods allow are described. T2 - Workshop on Advanced Manufacturing (WAM) 2025 CY - Grenoble, France DA - 03.06.2025 KW - Residual stress KW - Diffraction KW - AGIL KW - Laser powder bed fusion KW - MANUFACT PY - 2025 AN - OPUS4-64137 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schröder, Jakob T1 - Peculiarities of the determination of residual stress in additively manufactured materials N2 - The determination of residual stress in additively manufactured materials is a challenge, even after decades from the establishment of the basics of residual stress analysis. This is due to the peculiar microstructure of such materials. In fact, researchers have discovered that conventional methods for the determination of RS in materials do not properly work for AM materials. In this tutorial, the basics of RS analysis will be explained, together with the basics of AM manufacturing techniques. The microstructure of the peculiar materials (AM) dealt with here will be elucidated. Successively, the necessary modifications to the conventional approaches to RS analysis will be explained and case studies will be displayed, for the attendant to touch with hands the peculiarities of the approaches. Finally, a few experimental and theoretical tips will be given on dos and don’ts for a correct determination of RS in AM materials. T2 - 11th European Conference on Residual Stresses CY - Prague, Czech Republic DA - 03.06.2024 KW - Additive Manufacturing KW - Laser Powder Bed Fusion KW - Residual Stress KW - Diffraction PY - 2024 AN - OPUS4-60428 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bruno, Giovanni T1 - 3D imaging and residual stress analysis of AM Materials N2 - In this seminar, the capabilities for materials characterization at Division 8.5, BAM will be shon. Particular focus will be given to residual stress analysis and defect imaging in additively manufactured materials and components T2 - Skoltech - The 3rd International Workshop of Advanced Manufacturing Technologies CY - Online meeting DA - 18.04.2023 KW - Neutron Diffraction KW - X-ray diffraction KW - X-ray Computed Tomography KW - X-ray refraction radiography KW - Residual stress KW - Additive manufacturing PY - 2023 AN - OPUS4-57360 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Shashev, Yuri T1 - Optimizing the performance of phase gratings for better visibility in Talbot- Lau interferometry N2 - We investigated the efficiency of phase gratings, i.e., the visibility upon variation of different parameters. Rotating around an axis parallel to the grid lines of the phase grating changes the grating’s shape and thereby the initial distribution of phase shifts. This yields high visibilities for shorter propagation distances than derived from box shapes. Tilting the grating in the scattering plane allows continuous tuning of the grating’s height that corresponds to an ideal phase shift for a particular photon energy. This opens the way for tuning the design energy suitable for the material under investigation. Our study included simulations for monochromatic sources with the sampling procedure. T2 - PhD Day 2015 CY - Berlin, Germany DA - 14.7.2015 KW - Talbot-Lau interferometry PY - 2015 AN - OPUS4-38325 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schröder, Jakob T1 - The heat treatment of L-PBF Inconel 718: A manyfold problem N2 - The interest to additively manufacture Nickel-based superalloys has substantially grown within the past decade both academically and industrially. More specifically, additive manufacturing processes such as laser powder bed fusion (LPBF) offer the ability to produce dense parts within a single manufacturing step. In fact, the exceptional freedom in design associated with the layer-based nature of the processes is of particular interest for the complex shapes typically required in turbine applications. In certain cases, the overall part performance can be achieved by tailoring the microstructure and the crystallographic texture to the specific application. However, these advantages must be paid at a price: the large local temperature gradients associated with the rapid melting and solidification produce parts that inherently contain large residual stress in the as-manufactured state. In addition, the presence of pores in the final part may further affect the in-service part failure. As among Nickel-based alloys Inconel 718 exhibits excellent weldability, this alloy has been widely studied in open research in the domain of LPBF. However, significant microsegregation of the heavier alloying elements such as Niobium and Molybdenum accompanied by dislocation entanglements may preclude the application of conventional heat treatment schedules. Therefore, different post processing heat treatments are required for laser powder bed fused Inconel 718 as compared to conventional variants of the same alloy. In this study, we investigated two different heat treatment routes for LPBF Inconel 718. In a first routine, the samples were stress relieved and subsequently subjected to hot isostatic pressing (HIP) followed by a solution heat treatment and a two-step age (referred to as FHT). In a second routine, the samples were subjected to a single-step direct age post stress relieving heat treatment (referred to DA). We investigated the consequences of such heat treatment schedules on the microstructure, texture, and mechanical behavior. We show that by applying a DA heat treatment the typical columnar microstructure possessing a crystallographic texture is retained, while an equiaxed untextured microstructure prevails in case of an FHT heat treatment. We further evaluate how these heat treatments affect the mechanical behaviour on the macroscopic and microscopic scale. T2 - 4th European Symposium on Superalloys and their Applications EuroSuperalloys 2022 CY - Bamberg, Germany DA - 18.09.2022 KW - Electron Backscatter Diffraction KW - Additive Manufacturing KW - Laser Powder Bed Fusion KW - Mechanical Behavior KW - Heat Treatment KW - X-Ray Diffraction PY - 2022 AN - OPUS4-55811 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sprengel, Maximilian T1 - Heat treatment induced residual stress relaxation in additively manufactured L-PBF 316L stainless steel N2 - Residual stress relaxation as a function of heat treatment strategies in laser based powder bed fused 316l samples. T2 - Eleventh Joint BER II and BESSY II User Meeting CY - Berlin, Germany DA - 04.12.2019 KW - Additive Manufacturing KW - Residual Stress KW - Neutron Diffraction KW - 316L PY - 2019 AN - OPUS4-49851 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mieller, Björn T1 - Concept and Manufacturing of a Pressure Sensor Based on al LTCC Thin Film Strain Gauge T2 - IMAPS/ACerS 10th Int. Conf. and Exhib. on Ceramic Interconnect and Ceramic Microsystems Technolgies (CICMT 2014) CY - Osaka, Japan DA - 2014-04-14 PY - 2014 N1 - Geburtsname von Mieller, Björn: Brandt, B. - Birth name of Mieller, Björn: Brandt, B. AN - OPUS4-31324 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Bernd R. T1 - Microstructure characterization of materials using X-ray refraction techniques N2 - X-ray imaging techniques have an enormous potential to understand the microstructure, its evolution, and its link to mechanical, thermal, and transport properties. In this lecture we report the use of a powerful, yet not so wide-spread, set of X-ray techniques based on refraction effects. X-ray refraction allows determining the internal specific surface of materials (surface per unit volume) in a non-destructive fashion, position and orientation sensitive, and with a nanometric detectability. We demonstrate showcases of ceramics and composite materials, where microstructural parameters could be achieved in a way unrivalled even by high-resolution techniques such as electron microscopy or computed tomography. We present in situ analysis of the damage evolution during tensile load and the identification of void formation in parts produced by selective laser melting. T2 - MIMENIMA Summerschool CY - TU-Bremen, Germany DA - 22.8.2018 KW - X-ray refraction KW - Cracks KW - Pores PY - 2018 AN - OPUS4-45790 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bruno, Giovanni T1 - A paradigm shift in the description of creep in metals can only occur through multi-scale imaging N2 - The description of creep in metals has reached a high level of complexity; fine details are revealed by all sorts of characterization techniques and different theoretical models. However, to date virtually no fully microstructure-driven quantitative description of the phenomenon is available. This has brought to interesting inconsistencies; the classic description of (secondary) creep rests on the so-called power law, which however: a- has a pre-factor spanning over 10 orders of magnitude; b- has different reported exponents for the same material; c- has no explanation for the values of such exponents. Recently, a novel description (the so-called Solid State Transformation Creep (SSTC) Model) has been proposed to tackle the problem under a different light. The model has two remarkable features: 1- it describes creep as the accumulation of elementary strains due to dislocation motion; 2- it predicates that creep is proceeding by the evolution of a fractal arrangement of dislocations. Such description, however, needs a great deal of corroborating evidence, and indeed, is still incomplete. To date, we have been able to observe and somehow quantify the fractal arrangement of microstructures through Transmission Electron Microscopy (TEM), observe the accumulation of dislocations at grain boundaries by EBSD-KAM (Electron Back-Scattered Diffraction-Kernel Angular Misorientation) analysis, quantify the kinetic character (solid state transformation) of experimental creep curves, and estimate the sub-grain size of the fractal microstructure through X-ray refraction techniques. All pieces of the mosaic seem to yield a consistent picture: we seem being on the right path to reconstruct the whole elephant by probing single parts of it. What is still missing is the bond between the various scales of investigation. T2 - Korrelative Materialcharakterisierung 2022 CY - Dresden, Germany DA - 13.10.2022 KW - X-ray refraction KW - EBSD KW - Alloys KW - TEM KW - SEM PY - 2022 AN - OPUS4-56163 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Léonard, Fabien T1 - On nominal-actual comparisons for additive manufacturing applications N2 - Nominal-actual comparisons are routinely performed to compare a manufactured specimen to a reference specimen. X-ray Computed Tomography (CT) has brought a profound change in the way that tolerance verifications are performed in industry, by allowing the inner and outer geometries of an object to be measured, without the need for external access or destructive testing. As a results, CT is increasingly used in additive manufacturing applications, where a nominal-actual comparison performed between the digital model (CAD file), used as an input for the 3D printer, and the CT volume from the printed part, can provide invaluable information as to the accuracy of the printing process. However, the nominal-actual comparison process is somewhat different when applied to additively manufactured specimens by comparison to conventionally manufactured specimens. T2 - 9th Conference on Industrial Computed Tomography CY - Padova, Italy DA - 14.02.2019 KW - Computed tomography KW - X-ray computed tomography PY - 2019 AN - OPUS4-47833 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thiede, Tobias T1 - Der Einfluss der Probenabtrennung von der Bauplatte auf den Eigenspannungszustand in SLM IN718 N2 - Die Schicht-für-Schicht additive Fertigung (AM) in Form des selektiven Laserschmelzens (SLM) bietet einerseits Vorteile bezüglich des Probendesigns, andererseits sind thermische Eigenspannungen (ES) aufgrund des hohen Temperaturgradienten unvermeidbar. Diese Eigenspannungen wurden in zwei SLM-gefertigten Proben aus IN718 zerstörungsfrei mit Neutronenstreuung hinsichtlich der folgenden zwei Einflüsse analysiert: der Einfluss der Hatch-Länge und das Abtrennen des Werkstücks von der Bauplatte. Begleitet wurden die Messungen der Eigenspannungen durch optische Mikroskopie und die taktile Vermessung der Oberfläche. Eine Korrelation zwischen den Eigenspannungen und der Hatch-Länge konnte beobachtet und erklärt werden. T2 - 2. Tagung des DVM-Arbeitskreises Additiv gefertigte Bauteile und Strukturen CY - Berlin, Germany DA - 09.11.2017 KW - Additive Fertigung KW - Selektives Laserschmelzen KW - Eigenspannungen KW - Neutronenstreuung KW - IN718 PY - 2017 AN - OPUS4-42947 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Léonard, Fabien T1 - Metrology for Additively Manufactured Medical Implants: The MetAMMI project N2 - Additive manufacturing (AM) offers an effective solution to the medical sector. It enables the production, on demand, of customised implants which match the patient’s anatomy, with grafts that promote bone growth, as well as surgical guides that help the surgeons. The objective of this project is to provide a comprehensive basis to enable the safe use of medical AM products with traceable and reliable dimensionalmeasurements. This will guarantee the reliability of medical AM products to notified bodies and facilitate acceptance of AM in the medical sector for a better quality of life. T2 - BPWT/BAM Workshop " Innovative Materialien und Qualitätskontrolle für additive Fertigung" CY - Berlin, Germany DA - 12.09.2018 KW - Additive manufacturing KW - X-ray computed tomography PY - 2018 AN - OPUS4-45926 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Laquai, René T1 - Distinguishing characteristic defect in additively manufactured Ti-Al6-V4 with synchrotron X-ray refraction radiography N2 - Synchrotron X-ray refraction radiography (SXRR) is proven to identify different kinds of defects in Ti-Al6-V4 samples produces by selective laser melting. Namely, these defect types are empty pores and unprocessed powder, which are characteristic to the regions above and below the optimal laser energy density, respectively. Furthermore, SXRR detects small defects below the spatial resolution. T2 - BESSY User Meeting CY - Berlin, Germany DA - 13.12.2017 KW - Additive manufacturing KW - X-ray refraction KW - Porosity PY - 2017 AN - OPUS4-43446 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stegemann, Robert T1 - Characterization of Residual Stress State on Intert Gas Welded Joints by Neutron Diffraction at E3 line T2 - 7th joint BER II and BESSY II User Meeting CY - Berlin DA - 2015-12-11 PY - 2015 AN - OPUS4-35070 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Evans, Alexander T1 - Non destructive characterization in Additive manufacturing N2 - An overview of non destructive characterisation in additively manufactured materials using computed tomography, refraction and diffraction based stress analysis T2 - BAM-IFW workshop CY - IFW Dresden, Germany DA - 28.03.2019 KW - Residual stress analysis KW - Additive manufacturing KW - Computed tomography KW - Diffraction KW - X-ray refraction PY - 2019 AN - OPUS4-49842 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bruno, Giovanni T1 - An assessment of bulk residual stress in selective laser melted in 718 N2 - Having been introduced almost two decades ago, Additive Manufacturing (AM) of metals has become industrially viable for a large variety of applications, including aerospace, automotive and medicine. Powder bed techniques such as Selective Laser Melting (SLM) based on layer-by-layer deposition and laser melt enable numerous degrees of freedom for the geometrical design. Developing during the manufacturing process, residual stresses may limit the application of SLM parts by reducing the load bearing capacity as well as induce unwanted distortion depending on the boundary conditions specified in manufacturing. The residual stress distribution in IN718 elongated prisms produced by SLM was studied non-destructively by means of neutron (bulk) and laboratory X-ray (surface) diffraction. The samples with different scanning strategies, i.e. hatching length, were measured in as-built condition (on a build plate) and after removal from the build plate. While surface stress fields seem constant for AB condition, X-ray diffraction shows stress gradients along the hatch direction in the RE condition. The stress profiles correlate with the distortion maps obtained by tactile probe measurements. Neutron diffraction shows bulk stress gradients for all principal components along the main sample directions. We correlate the observed stress patterns with the hatch length, i.e. with its effect on temperature gradients and heat flow. The bulk stress gradients partially disappear after removal from the baseplate. Together with surface scan utilizing a coordinate-measuring machine (CMM), it is possible to link the stress release to the sample distortion. We finally propose an explanation of those stress profiles based on the deposition strategy. T2 - ECRS10 CY - Leuven, Belgium DA - 09.09.2018 KW - Residual stress KW - Influence of rheology modifying admixtures on hydration of cementitious suspensions PY - 2018 AN - OPUS4-45997 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bruno, Giovanni A1 - Cabeza, Sandra T1 - Neutron diffraction: the forgotten non-destructive technique for residual stress analysis … and more N2 - 3-D Stress Analysis (Bulk) Stress mapping Thick (and thin) films & Interfaces Bulk high temperature Real time In-situ testing: Large sample environment (Stress rigs, Furnaces, …) Neutrons and Synchrotron Radiation allow all this because they are FASTER , DEEPER and MORE PRECISE than lab equipment (Flux)(Energy)(Parallel Beam) T2 - World Non Destructive Testing CY - München, Germany DA - 11.06.2016 KW - Neutron diffraction KW - Stress analysis PY - 2016 AN - OPUS4-38396 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schröder, Jakob T1 - On the influence of heat treatment on microstructure and mechanical behavior of laser powder bed fused Inconel 718 N2 - Since additive manufacturing processes typically introduce heterogeneous microstructures and residual stresses, the applicability of parts produced in an as-built state is limited. Therefore, often different post-processing treatments are necessary to obtain the desired stress state and properties. For additively manufactured Inconel 718, the recently developed standard ASTM F3301 provides guidance for the heat treatment of powder bed fusion specimens. Although this standard is based on standards developed for wrought Inconel 718, it does not include the direct aging variant. In this study, we characterized the microstructure and tensile behavior of Inconel 718 specimens produced by a laser powder bed fusion process. The specimens were heat-treated according to two different routines after stress relieving: a full heat treatment cycle versus a one-step aging process. Differences in the resulting texture and grain morphology were observed. Although these differences prevail, the ex-situ tensile behavior was broadly similar. Minor differences were observed in yield strength and work hardening rate for the direct aged specimen. In order to understand this behavior, investigations with in-situ tensile testing during synchrotron energy-dispersive X-ray diffraction measurements revealed differences in the load partitioning among different crystal directions. This was attributed to microstructural differences between the heat treatment variants. Further analysis emphasized that the various strengthening mechanisms are present to a different extent depending on the heat-treatment cycle applied. In addition, the elastic anisotropy expressed by the differences in the diffraction elastic constants displayed a dependence on the microstructure. Importantly, a precise knowledge of such constants is indispensable to reliably determine residual stresses in parts. T2 - EUROMAT 2021 - European Congress and Exhibition on Advanced Materials and Processes CY - Online meeting DA - 13.09.2021 KW - Electron microscopy KW - X-ray analysis KW - Inconel 718 KW - Additive manufacturing (AM) KW - Mechanical behavior KW - Diffraction elastic constants (DECs) PY - 2021 AN - OPUS4-53301 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stegemann, Robert T1 - Evaluation magneto-mechanischer Effekte in hochauflösenden Magnetfeldmessungen durch Neutronendiffraktion N2 - Die mechanische Spannung ist ein maßgeblicher Parameter ferromagnetischer Materialien. Wird ein solches Material unter die Curie Temperatur abgekühlt, zerfällt es spontan in nahezu selbstgesättigte magnetische Domänen. Diese Magnetisierung führt gleichzeitig zu einer Verformung der mit ihr gekoppelten Kristallgitter. Ein Effekt der auch reziprok gilt: wird die Gitterverformung durch eine Spannung behindert ändert sich zwangsweise der magnetische Zustand. Man kann annehmen, dass zwischen unterschiedlichen, für sich aber homogen verspannten Werkstoffbereichen, lokale magnetische Streufelder auftreten, weil magneto-mechanische Effekte eine Inkompatibilität der Domänenstruktur induzieren. Bekanntlich bilden sich Spannungsgradienten nach Schweißprozessen durch ungleichmäßigen Wärmeeintrag, thermischer Dehnung, und unterschiedlichen Abkühlraten aus. Unter dieser Prämisse untersuchen wir Wolfram-Inertgas geschweißte Blindnahtproben (250x100x4,8 mm^3) aus einem hypereutektoiden Baustahl. Der Spannungszustand der Proben wurde anhand von Neutronendiffraktometrie (ND) am Instrument E3 am Reaktor BERII (Helmholzzentrum Berlin, HZB) charakterisiert. ND ist ein Referenzverfahren für die quantitative Bestimmung von elastischen Dehnungen in kristallinen Materialien, deren Gitter selbst der Messmaßstab ist. Die Auswertung zeigt hohe Längsspannungen mit lokalen Maxima in Größenordnung von 600 MPa, die von umgebenen Druckspannungszonen kompensiert werden. Zur Detektion der magnetischen Kleinststreufelder verwenden wir speziell designte GMR-Sensorik (GMR - Giant Magneto Resistance), die aufgrund der geringen Größe ihrer aktiven Sensorelemente hohe Ortsauflösung mit Sensitivität vereint. Die Visualisierung der Messergebnisse lässt eine klare magnetische Mikrostruktur der Schweißnähte erkennen, in der die Streufelder lateral in Größenordnung des Erdmagnetfeldes variieren (~50 µT). Wir zeigen durch einen Vergleich beider Messverfahren, dass lokale magnetische Streufeldmaxima in hohem Maße mit den Spannungsgradienten übereinstimmen. T2 - DGZfP-Jahrestagung CY - Koblenz, Germany DA - 22.05.2017 KW - GMR-Sensorik KW - Neutronendiffratkion KW - Eigenspannungen KW - Baustahl PY - 2017 AN - OPUS4-40386 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hejazi, Bardia A1 - Fritsch, Tobias A1 - Benz, Christopher A1 - Radtke, Lars A1 - Sander, Manuela A1 - Bruno, Giovanni T1 - In-situ very high cycle fatigue experiments of additively manufactured Ti-6Al-4V using X-ray computed tomography N2 - X-ray computed tomography (XCT) is an invaluable method for evaluating the properties and performance of components both during service and after failure in a non-destructive manner. XCT is particularly useful for the investigation of additively manufactured (AM) components, which often have production defects that are inherent to the manufacturing process, such as lack of fusion defects. Understanding the mechanisms of fatigue crack growth throughout the life cycle of such components is crucial and so to address this need, we designed and performed experiments to investigate the fatigue life and fatigue crack growth behavior of Ti-6Al-4V components under very high cycle fatigue (VHCF) testing. The titanium samples were additively manufactured with intentional internal defects to control crack initiation location. XCT of the component was carried out to identify crack initiation sites and characterize the dynamics of crack growth. The findings from this work will benefit industries that rely on the AM of titanium alloys, aiding in the improvement of component design and manufacturing processes. T2 - Alloys for additive manufacturing 2025 (AAMS 2025) CY - Neuchâtel, Switzerland DA - 02.09.2025 KW - X-ray computed tomography KW - Deep learning KW - Titanium alloy KW - Very high-cycle fatigue PY - 2025 DO - https://doi.org/10.5281/zenodo.15261296 AN - OPUS4-64096 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bruno, Giovanni T1 - In-Situ Compression CT on Additively Manufactured in 625 Lattice Structures N2 - The porosity and the surface roughness are recently discussed problems for SLM parts. The influence of SLM process parameters on porosity is well studied for different materials. Nevertheless, the build angle (i.e. the angle between part orientation and build plate) needs to be understood as an additional SLM process parameter, as it has been shown, that the microstructure and hence the mechanical performance of various materials depend on the build angle. The inherent build angle of each strut as a part of a lattice structure is the motivation to investigate the influence of the build angle on the porosity and roughness on round-shaped (1 mm diameter) struts by means of CT. Conventional Coordinate Measuring Machine (CMM) has the limitation towards small and round shaped samples. The need for Computed Tomography (CT) regarding investigations of SLM parts will increase because no other non-destructive technique allows the assessment of complex geometries with inner laying surfaces. We used CT to assess the pores and the strut surface. Seven struts out of the nickel alloy Inconel 625 with build angles from 30° to 90° were studied. It was found that the number of pores is smaller, and the size of pores is larger for the 90° strut. In case of 30° strut, the number of pores is increased towards down-skin side, additionally, this strut orientation showed to have the largest number of attached powder particles. The elongated pores exist exclusively near the strut surface. While the roughness at the down-skin surface is highly depending of the biud angle, the roughness at the up-skin surface is the same for all struts. The mechanisms of pore and surface roughness formation is not mainly driven by gravity. T2 - ISAM Konferenz 2019 CY - Dresden, Germany DA - 29.01.2019 KW - Computed Tomography KW - Additive Manufacturing KW - Metals KW - Microstructure PY - 2019 AN - OPUS4-47327 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kupsch, Andreas T1 - Optimizing visibility of phase gratings for Talbot-Lau X-ray imaging N2 - We investigated the efficiency of phase gratings, i.e., the visibility upon variation of different parameters. Rotating around an axis parallel to the grid lines of the phase grating changes the grating’s shape and thereby the initial distribution of phase shifts. This yields high visibilities for shorter propagation distances than derived from box shapes. Tilting the grating in the scattering plane allows continuous tuning of the grating’s height that corresponds to an ideal phase shift for a particular photon energy. This opens the way for tuning the design energy suitable for the material under investigation. Our study included simulations for monochromatic sources with the sampling procedure for rectangular and triangular phase gratings. T2 - User-Meeting CY - Berlin, Germany DA - 8.12.2016 KW - Talbot-Lau interferomerty KW - Phase grating KW - Synchrotron radiation PY - 2016 AN - OPUS4-39096 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Riedel, Jens T1 - Acoustic Ion Manipulation: Electric-field-free Approach to Gate, Focus, and Separate Ions at Atmospheric Pressure N2 - Approaches to control the motion and direction of ionized particles and mole-cules are an essential aspect of ion-based spectrometries, such as mass spec-trometry (MS) and ion mobility spectrometry (IMS). A wide variety of ion optics exist to reflect, focus, separate, gate, and filter ions based on physical proper-ties. Notably all rely on electric and magnetic fields to alter the trajectory of ionized atoms and molecules. While these optics are quite efficient at low pressures due to the large mean free path, diffusion and electrostatic repulsion between ions dominate at higher pressures. Conventional ion optics, that use electric or magnetic fields, can guide ions at atmospheric pressure (AP), but require high field strengths to overcome the dominating aerodynamic effects. Here, we describe a remarkable phenomenon whereby low-power acoustic fields are used to move, shape, gate, and separate beams of gaseous ions at atmospheric pressure. We refer to this approach as Acoustic Ion Manipulation (AIM). Gaseous ions at AP are directed towards and separated by the presence of the acoustic field. To better understand the phenomenon, an ion-detector array provided a measure of bulk ion movement, while mass spectrometry (MS) offered chemical-specific information. As one example of an AIM setup, a standing acoustic wave was formed with two ultrasonic speakers and placed between an ionization source and ion detector. Ion beams preferentially travel through regions of stable pressure gradients (i.e. nodes) and deflect from un-stable regions (i.e. antinodes). Shadowgraphy revealed that the ions are sepa-rated from a neutral gas stream. Specific examples of ion focusing, gating, and separation (based on ion size) will be shown. In addition, experimental findings will be used to postulate a theory to develop a better understand of the behav-ior of gas-phase ions in acoustic fields. This discovery could have profound im-pacts in IMS/MS instrumentation as well as materials processing and charac-terization. T2 - 56. Jahrestagung der DGMS CY - Göttingen, Germany DA - 04.03.2025 KW - Acoustic Ion Manipulation KW - Mass spectrometry KW - Ultrasound PY - 2025 AN - OPUS4-64208 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mieller, Björn T1 - Sintering and interconnecting thermoelectric oxides for energy applications N2 - Today, more than 12% of the primary energy is lost in the form of waste heat. Thermoelectric generators (TEGs) can convert waste heat directly into electrical power by utilizing the Seebeck effect. The performance of such a generator is defined by a dimensionless figure of merit ZT of the thermoelectric pairs and the resistance R of the metallic contacts between these pairs. The figure of merit of thermoelectric oxides is considerably smaller compared to semiconductors. Still, thermoelectric oxides like calcium cobaltite (Ca3Co4O9) are attractive for applications at elevated temperatures in air. In contrast to the established π-type architecture of common TEGs, tape casting and multilayer technology may be applied for cost-effective manufacturing of oxide TEGs. Promising demonstrations of multilayer TEGs have been published in the last years. Still, the development of reliable and scalable manufacturing processes and proper material combinations is necessary. The aim of our project is to evaluate the feasibility of low temperature co-fired ceramics (LTCC) technology for a practical manufacturing of oxide multilayer TEGs of Ca3Co4O9 (p-type) and calcium manganate (CaMnO3, n-type). Ca3Co4O9 exhibits an undesired phase decomposition at 926 °C. Because of that, the application of sintering strategies and interconnect concepts well known from LTCC technology is a promising approach. We present results of pressure-assisted sintering of Ca3Co4O9 multilayer at 900 °C and axial pressures of up to 7.5 MPa. Ca3Co4O9 was produced by solid state reaction of CaCO3 and cobalt(II,III)oxide at 900 °C. Green tapes were prepared by a doctor-blade process, manually stacked and laminated by uniaxial thermocompression. Sintering was conducted in a LTCC sintering press between SiC setter plates. The thickness shrinkage was recorded by an in-situ technique. After sintering under 7.5 MPa, the microstructure of the single phase material shows a high density of 95 % and an advantageous alignment of the platelet grains. This results in good electrical conductivity and a comparatively high ZT of 0.018 at room temperature. However, the lowering of CaMnO3 sintering temperature from above 1200 °C to below 920 °C remains a challenge. To select a proper metal paste for interconnections of an oxide TEG, several pastes have been investigated regarding contact resistance of internal and external (soldered) connections in a preliminary study. Commercial pastes containing Ag, Au, Au/Pt, Ag/Pd, and Ag/Pd/Bi were manually applied and post-fired on sintered test bars of Ca3Co4O9 and CaMnO3 at 900 °C for 2 h. All tested pastes formed mechanically stable metallization after firing. For resistance measurement, 4-wire method and a custom-made probe head were used. The contacts on Ca3Co4O9 exhibit significantly (2-sample t-test, α = 5%) higher resistance compared to contacts on CaMnO3. Pure silver paste exhibits the lowest resistance for internal contacts on both materials, lower than 5 mΩ on CaMnO3. Ag/Pd/Bi paste resulted in conspicuously high variance of resistance. EDX analyses clarified an enrichment of Bi in the thermoelectric material near the interface and thereby the formation of an oxide layer with probably high electrical resistance. The thickness of that layer varies with the thickness of metallization. In conclusion, the use of Bi containing pastes is not advisable. Pure Ag paste shows the best results regarding resistance and solderability. T2 - CICMT 2018 CY - Aveiro, Portugal DA - 18.04.2018 KW - Thermoelectric oxide KW - Thermoelectric generator KW - Multilayer technology KW - Pressure-assisted sintering PY - 2018 AN - OPUS4-44740 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kromm, Arne T1 - Residual stress formation in selective laser melted parts of alloy 718 N2 - Additive Manufacturing (AM) through the Selective Laser Melting (SLM) route offers ample scope for producing geometrically complex parts compared to the conventional subtractive manufacturing strategies. Nevertheless, the residual stresses which develop during the fabrication can limit application of the SLM components by reducing the load bearing capacity and by inducing unwanted distortion, depending on the boundary conditions specified during manufacturing. The present study aims at characterizing the residual stress states in the SLM parts using different diffraction methods. The material used is the nickel based superalloy Inconel 718. Microstructure as well as the surface and bulk residual stresses were characterized. For the residual stress analysis, X-ray, synchrotron and neutron diffraction methods were used. The measurements were performed at BAM, at the EDDI beamline of -BESSY II synchrotron- and the E3 line -BER II neutron reactor- of the Helmholtz-Zentrum für Materialien und Energie (HZB) Berlin. The results reveal significant differences in the residual stress states for the different characterization techniques employed, which indicates a dependence of the residual state on the penetration depth in the sample. For the surface residual stresses, longitudinal and transverse stress components from both X-ray and synchrotron agree well and the obtained values were around the yield strength of the material. Furthermore, synchrotron mapping disclosed gradients along the width and length of the sample for the longitudinal and transverse stress components. On the other hand, lower residual stresses were found in the bulk of the material measured using neutron diffraction. The longitudinal component was tensile and decreased towards the boundary of the sample. In contrast, the normal component was nearly constant and compressive in nature. The transversal component was almost negligible. The results indicate that a stress re-distribution takes place during the deposition of the consecutive layers. Further investigations are planned to study the phenomenon in detail. T2 - Forschungsseminar OvGU Magdeburg CY - Magdeburg, Germany DA - 15.11.2018 KW - Additive Manufacturing KW - Selective Laser Melting KW - Residual Stresses PY - 2018 AN - OPUS4-46876 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schröter, Felix T1 - Fluorescence? Not on my Shift! Excitation- Shifted UV Raman Microspectroscopy N2 - Spectroscopic analysis of samples provides elemental information, which is useful when the sample is homogenous. But many samples are not and consequently the creation of maps detailing the spatial composition of materials is needed. Raman microscopy can be used for this exact purpose but suffers a big drawback. The inherently weak Raman scattering results in long measurement times, especially when maps with many data points are created. This is due to the long exposure times needed when visible light lasers are used. A shift to UV-Lasers significantly increases the Raman intensity, as it scales with the fourth power of the inverse of the laser wavelength. But UV excitation often leads to fluorescence which can obscure the relatively weak Raman signal. Consequently, UV-Raman can only be used with specially prepared samples, for example through photo-bleaching, or with samples producing no fluorescence background in the measurement region. A solution is proposed that uses shifted-excitation Raman difference spectroscopy (SERDS) in a confocal microscope to obtain fluorescence-free Raman spectra. This is possible due to the collection of two Raman spectra at different excitation wavelengths. SERDS then allows for the calculation of just the Raman signal from the difference spectrum, which eliminates any fluorescence backgrounds, as they are not excitation wavelength dependent. The presented approach employs a polarized beamsplitter to irradiate the same spot with two lasers of different wavelengths which share the same beam path in the microscope. Consequently, a SERDS UV Raman Microscope is created, which utilizes the speed of UV-Raman without the drawbacks of possible broad fluorescence backgrounds. Here we present the instruments methodology and some first results. T2 - ANAKON 2025 CY - Leipzig, Germany DA - 10.03.2025 KW - UV Raman Spectroscopy KW - UV Raman Microspectroscopy KW - Confocal Microscopy KW - Excitation-Shifted Raman Spectroscopy PY - 2025 AN - OPUS4-62734 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Blume, Simon T1 - Exploiting Lithium Self-Absorption in a Laser-Induced Breakdown Plasma for Isotopic Analysis via Spatial Heterodyne Spectroscopy N2 - Lithium-ion batteries are ubiquitous in modern life. From powering consumer electronics to enabling electric mobility and energy storage, they are a key building block of a sustainable future. Determination of the ratio of the two naturally abundant stable isotopes, 7Li and 6Li, provides access to a wide variety of information, such as studying the aging processes of lithium-ion batteries or elucidating the isotopic fingerprinting of natural or recycled sources of lithium. However, accurately measuring the lithium isotope ratio in complex samples remains challenging, often requiring either extensive sample pretreatment or specialized equipment, thus impeding in-situ and high-throughput demands of global industries. Recognition and determination of the individual lithium isotopes with conventional laser-induced breakdown spectroscopy (LIBS) setups is nearly impossible. While LIBS offers several advantages, such as obviating time- and resource-intensive sample preparation and enabling rapid measurements, the high temperature (~20,000 K) of the plasma, as well as the Stark-broadening caused by the nascent free electrons spectrally broaden the atomic emission lines to such an extent that the isotopic shift of the lithium doublet at 670 nm cannot be resolved. Since, the excited state energy for this transition amounts to only 14,900 cm-1, lithium exhibits a pronounced self-absorption dip in the emission signal. This self-absorption dip is significantly less affected by the broadening effects, therefore, allowing for the resolution of the isotopic shift from its line shape. Spatial heterodyne spectroscopy (SHS) offers the superior resolution capabilities necessary to differentiate the individual isotopic contributions. To address the generally limited sensitivity of SHS, a high-repetition-rate (>10 kHz) laser allows the accumulation of more than 10,000 lasing events per spectral recording for a sufficient signal-to-noise ratio and gain statistical validity. Optical lithium fluoride serves as a model sample to showcase the analytical performance. Additionally, the impact of the laser parameters on the self-absorption will also be discussed. T2 - ANAKON 2025 CY - Leipzig, Germany DA - 10.03.2025 KW - Isotopic Analysis KW - Spatial Heterodyne Spectroscopy PY - 2025 AN - OPUS4-63559 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sander, Luise T1 - Multi-Scale Analysis of Commercially Available Sodium-Ion Cells N2 - As the first commercial sodium-ion-batteries (SIBs) are available for purchase, it is possible to investigate material composition. Gaining an insight into the material composition of these SIBs is of interest not only for the classification of possible safety risks and hazards, but also in regards to recycling. Herein we report the preliminary investigations of the chemical and structural composition of first commercial SIB-cells. Two different SIB-cells with different specification were compared regarding electrode size, thickness and further parameters. Furthermore, the composition of the active materials and electrolyte was investigated and compared. T2 - Solid State Ionics (SSI) CY - London, United Kingdom DA - 15.07.2024 KW - Sodium Ion-Cells KW - Multi-Scale PY - 2024 AN - OPUS4-60764 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bresch, Sophie T1 - Lowering the sintering temperature of calcium manganate CaMnO3 for thermoelectric applications N2 - Thermoelectric materials can convert waste heat directly into electrical power by utilizing the Seebeck effect. Calcium cobaltite (p-type) and calcium manganate (n-type) are two of the most promising oxide thermoelectric materials. The development of cost-effective multilayer thermoelectric generators requires the co-firing of these materials and therefore the adjustment of sintering temperatures. Calcium manganate is conventionally sintered between 1200 °C and 1350 °C. Calcium cobaltite exhibits an undesired phase transition at 926 °C but can be sintered to high relative density of 95 % at 900 °C under axial pressure of 7.5 MPa. Hence, co-firing at 900 °C would be favourable. Therefore, strategies for lowering the sintering temperature of calcium manganate have been investigated. Basically, two approaches are common: i) addition of low melting additives like Bi2O3-ZnO-B2O3-SiO2 (BBSZ) glass or Bi2O3, and ii) addition of additives that form low-melting eutectics with the base material, for example CuO. In this study, several low melting additives including BBSZ glass and Bi2O3, as well as CuO were tested regarding their effect on calcium manganate densification. Bi2O3 did not improve the densification, whereas BBSZ glass led to 10 % higher relative density at 1200 °C. An addition of 4 wt% CuO decreases the temperature of maximum sinter rate from above 1200 °C to 1040 °C. By reducing the particle size of the raw materials from 2 μm to 0.7 μm the maximum sinter rate could be further shifted 20 K towards lower temperatures and the sinter begin decreased from 920 °C to 740 °C. It is shown that eutectic phase formation is more effective in lowering sintering temperature and accelerating densification than low-melting additives. T2 - 93. DKG-Jahrestagung und Symposium Hochleistungskeramik 2018 CY - Munich, Germany DA - 10.04.2018 KW - Thermoelectrics KW - Sinter additive PY - 2018 AN - OPUS4-44818 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - You, Yi T1 - Advanced Repetition-Rate Modulation and Computational Strategies for Background-Free LIBS Using Non-Gated Spectrometers N2 - Laser-induced breakdown spectroscopy (LIBS) is recognized for its rapid, direct elemental analysis capabilities. However, its general adoption is constrained by the reliance on expensive, high-power consumption, gated cameras such as intensified charge-coupled devices (CCDs). These devices, while sensitive, are expensive and possess low frame rates, limiting their efficacy in dynamic or challenging environments. Our study proposes an innovative approach that leverages non-gated spectrometers in conjunction with the framework of correlation spectroscopy to isolate analyte signals responsive to a specific repetition-rate modulation pattern, thereby yielding spectra with zero background. We utilized a diode-pumped solid-state laser, with repetition rates ranging from 10 Hz to 30 kHz, to induce plasma in aqueous solutions containing various alkaline and earth-alkaline metals. With a non-gated single-grating linear CCD spectrometer, we found that the continuum signal plateaued at approximately 7 kHz. In contrast, atomic emissions from the dissolved analytes showed continued increases. Notably, atomic emissions from the solvent (water) were observable only above 8.5 kHz, at a significant high rate of increase. Through computational synthesis of a modulation pattern, we determined an optimized scheme that effectively discriminates continuum and analyte signals; this pattern was optimized with a genetic algorithm. The spectral matrix correlating signal intensity with laser repetition rate and wavelength was used as the input of the model. Meanwhile, the fitness function that extracts the background-free spectra was built in-house and inspired by the Gardner transform, which exploits the power of Fourier transform, allowing for flagging and splitting analyte signal from other undesired features. This approach bypasses the limitations associated with gated cameras, while providing a cost-effective alternative for robust LIBS applications. This advancement is particularly relevant in field, portable and remote applications, aligning with the ongoing demand for accessible, high-performance analytical tools in diverse scientific fields. T2 - SCIX 2024 Conference CY - Raleigh, NC, USA DA - 20.10.2024 KW - LIBS KW - Data Processing KW - High Repetition Rate KW - Repetition Rate Modulation KW - Data-Oriented Experimental Design PY - 2024 AN - OPUS4-62137 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bruno, Giovanni T1 - Applications of X-ray refraction to non-destructive characterization of and composites T2 - 14th International Conference of the European Ceramic Society CY - Toledo, Spain DA - 2015-06-21 PY - 2015 AN - OPUS4-33974 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mieller, Björn T1 - Tieftemperaturfügen mit Nano- und Submikronsilberpasten T2 - DKG-Symposium "Fügen von Keramik: Grundlagen - Verfahren - Anwendungen" CY - Erlangen, Germany DA - 2012-12-04 PY - 2012 N1 - Geburtsname von Mieller, Björn: Brandt, B. - Birth name of Mieller, Björn: Brandt, B. AN - OPUS4-27285 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Arlt, Tobias T1 - Tomographic methods for investigation for fuel cell materials T2 - Ulm Electro Chemical Talks CY - Ulm, Germany DA - 2010-06-15 PY - 2010 AN - OPUS4-21518 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Anita T1 - Eine sichere Zukunft für Lithium-Ionen Batterien N2 - Eine sichere Zukunft hat eine Technologie dann, wenn sie die Gesellschaft auch von ihrer Sicherheit überzeugen kann. Dies ist insbesondere für Lithiumbatterien von hoher Bedeutung. Die BAM trägt auf den verschiedene Ebenen auf vielfältige Art und Weise dazu bei, diese Sicherheit zu untersuchen und zu verbessern. T2 - 4. Batterieforum Berlin Brandenburg CY - Potsdam, Germany DA - 22.11.2024 KW - LIthiumbatterien KW - Sicherheit PY - 2024 AN - OPUS4-62328 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Widjaja, Martinus Putra T1 - Accumulation of Fibre Breaks under Time Dependent Loads in CFRP Materials of Pressure Vessels N2 - BAM has discovered that the reliability of tested composite pressure vessel will be altered when the loading speed is varied. The ageing of composite materials in general gives negative effect to the structure, however there might be positive effect occurs due to the load redistribution between the fibres. The study on the negative effect of ageing has been compared favourably with the fibre break model from Mines ParisTech. To improve the model's capability, this positive effect should also be implemented. The problem however to evaluate real scale model that might take extensive computation time. The reduced volume method then was proposed to improve the calculation time. The next study is then to check the approach on different loading condition and compare the result with experimental data provided by BAM. T2 - PhD Day 2018 CY - Evry, France DA - 20.06.2018 KW - Fibre Break Accumulation KW - Carbon Fibre Pressure Vessels KW - Time Effect KW - Integral Range PY - 2018 AN - OPUS4-45567 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bruno, Giovanni T1 - A few Aspects of the Current Understanding of DPF Materials Thermal and Mechanical Properties N2 - Bi-continuous porous ceramics for filtration applications possess a particularly complicated microstructure, whereby porosity and solid matter are intermingled. Moreover, they very often display a microcrack network, resulting from the strong anisotropy of the microscopic coefficient of thermal expansion (CTE). Mechanical, thermal, and filtration properties, they all strongly depend on the morphology of both solid matter and porosity, and on the degree of microcracking (also, the microcrack density), which is in its turn tightened to the grain size. Recent industrial and academic research has enormously progressed in understanding the microstructure-property-performance relationships existing in these complicated materials: - Using 3D computed tomography (CT) at different resolutions, and several X-ray refraction-based techniques, porosity and pore orientation could be quantitatively evaluated (in the example of cordierite). - Neutron and X-ray Diffraction has been instrumental to disclose a) the non-linear character of the stress-strain response, and b) the negative CTE of these materials, and its consequences on the materials properties; - Analytical and numerical models have been elaborated to rationalize these behaviours in terms of microcracking and microstructural features. Here these results will be reviewed, and a outlook at (some of the) outstanding problems will be given. T2 - HELSMAC CY - Cambridge UK DA - 7.04.2016 KW - Thermal KW - Materials PY - 2016 AN - OPUS4-35752 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Blume, Simon T1 - Femtosecond Laser-induced XUV Spectroscopy (LIXS) for Elemental Analysis N2 - In a typical laser-induced breakdown spectroscopy (LIBS) setup, emissions from collisional excitation of the atoms in the later stages of the plasma are detected and provide information about the elemental fingerprint of the sample. However, precise measurements, in particular quantification efforts, suffer from fluctuations of the intensity of the detected emission lines due to matrix effects and plasma-flicker noise, as well as significant background noise. In contrast, the early stages of the plasma are dominated by electron-ion recombination and Bremsstrahlung, which lead to sharp and intense x-ray emissions with consistent intensity profiles between laser pulses and suppressed background noise, therefore improving the limit of detection, especially for lighter elements. These emissions are detected in laser-induced XUV spectroscopy (LIXS).[1] Introduction of a femtosecond laser (pulse length ~100 fs) to the LIXS setup fundamentally changes the laser energy absorption and ablation process. The laser pulse energy is absorbed and redistributed by multiphoton absorption and inverse Bremsstrahlung and operates on a time frame faster than the plasma formation. Additionally, the plasma formation itself is accelerated leading to signal generation in the XUV-range before generation of the undesired background emissions. Thus, utilization of a femtosecond laser allows for further suppression of broadband emissions from the plasma allowing for sharper separation of the emission lines and improved limit of detection. This work presents the results of the combination of a LIXS setup with a femtosecond laser and assess the capabilities of this system with a model sample of cathode material from a spent lithium-ion battery. T2 - AMACEE 2025 CY - Brno, Czech Republic DA - 26.8.2025 KW - LIXS KW - Femtosecond laser KW - Instrumentation PY - 2025 AN - OPUS4-64118 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Palásti, Dávid jenö T1 - Interferometric sensing in the UV range – Investigation and comparison of the all-reflective spatial heterodyne spectrometer designs N2 - Spatial heterodyne spectrometers (SHS) are optical interferometric devices, working in the UV and visible spectral ranges [1]. The most common SHS setup is similar to the Michelson interferometer, both utilizes a beam splitter in the incoming beam path. In case of the SHS the split beams are not aimed towards orthogonal mirrors, but reflective optical gratings, set under a selected angle. These optical gratings diffract the beams, the direction of every wavelength will depend on the grating constant and the angle of the gratings. The wavefronts belonging to different wavelengths are going to cross each other under a unique angle, resulting in a spatial interference, which is recorded by a digital camera. This relatively compact setup provides high resolution and light throughput, which properties were harnessed for tasks requiring good line separation and/or high sensitivity [2]. However, SHS are only applicable on wavelengths for which an adequate transmissive beam splitter is available like the visible range, but not the far UV. To overcome this limitation, different all-reflective designs were introduced [3]. These instruments utilize symmetric optical gratings for the splitting and recombination of the beams. Although these SHS devices solve the main limitations of the traditional ones, they come with their fair share of drawbacks as well, such as more complex arrangement and the requirement for more delicate tuning. The behaviour of the traditional SHS is well documented [4,5], but in regards of the all-reflective ones we have much less available information. In this current study we utilized computational modelling to predict the behaviour of the all-reflective SH spectrometers, with special attention to the effects of the different alignment errors. Later we utilize this knowledge to fine tune an SHS for sensing (LIBS, Raman) in the UV region. Furthermore, we are introducing two new all-reflective SHS setups and compering them to their older counterparts. T2 - ANAKON 2025 CY - Leipzig, Germany DA - 10.03.2025 KW - SHS KW - Spectroscopy PY - 2025 AN - OPUS4-63556 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mieller, Björn T1 - Anwendung der Master-Sinter-Kurve bei druckunterstützter Sinterung von Low Temperature Co-Fired Ceramics T2 - DKG-Jahrestagung 2014 CY - Clausthal-Zellerfeld, Germany DA - 2014-03-24 PY - 2014 N1 - Geburtsname von Mieller, Björn: Brandt, B. - Birth name of Mieller, Björn: Brandt, B. AN - OPUS4-30472 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bruno, Giovanni T1 - Evaluating Porosity in Cordierite DPF Materials: Advanced X-ray Techniques and New Statistical Anlaysis Methods T2 - CIMTEC 2014 CY - Montecatine Terme, Italy DA - 2014-06-08 PY - 2014 AN - OPUS4-30875 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bruno, Giovanni T1 - Analyse von Schädigungsprozessen in Beton - Was leistet die CT? Teil1: Einblick in die Computertomographie N2 - Ein Nachteil der klassischen Durchstrahlungstechnik mit Röntgenstrahlen ist die, in der Abbildung des Untersuchungsobjektes, fehlende Tiefeninformation. Die Anwendung von radiografischen Verfahren, die das Objekt unter zwei oder mehreren Winkelpositionen durchstrahlen, erlauben die Rekonstruktion räumlicher Abbildungen. Dazu zählen Stereoradiografie, Translations- und Rotationslaminographie. Bei der Computertomographie erfolgt die Durchstrahlung unter einem Winkelbereich von 180° oder 360°. Die dabei aufgenommenen Projektionen werden anschließend durch Anwendung der Fourier Transformation und der gefilterten Rückprojektion zu einem 3D-Bilddatensatz rekonstruiert. Verschiedene systembedingte Artefakte, die das Ergebnis negativ beeinflussen können, lassen sich durch geeignete Meß- und Rekonstruktionsparameter, sowie einer nachfolgende Bildverarbeitung eliminieren oder reduzieren. T2 - Summer School im Rahmen des DFG Schwerpunktprogramms 2020 "Zyklische Schädigungsprozesse in Hochleistungsbetonen im Experimental-Virtual-Lab" CY - Hotel Park Soltau, Soltau, Germany DA - 25.06.2018 KW - Computertomographie KW - Durchstrahlungsverfahren KW - Bildverarbeitung KW - Rekonstruktionsverfahren KW - Bildartefakte PY - 2018 AN - OPUS4-45432 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cabeza, Sandra T1 - Characterization of multiphase metal matrix composites by means of CT and neutron diffraction N2 - The present study examines the relationship between the microstructure of multiphase MMC and their damage mechanisms. The matrix AlSi12CuMgNi was combined with 15% vol. Al2O3 (short fibres) and with 7% vol. Al2O3 + 15% vol. SiC (short fibres and whiskers, respectively). The experimental approach encompasses 3D microstructure characterization by means of computed tomography of samples (a) as-received, (b) after heat treatment, and (c) after compression tests at room temperature. The volume fraction of different phases, their distribution, their orientation and the presence of defects and damage are studied. Influence of addition of SiC whiskers on mechanical properties of composite was investigated. Phase-specific load partition analysis for samples with fibre plane parallel to load was perform by using neutron diffraction measurements during in-situ compression. It shows damage in the Si phase, while Al2O3 short fibres carry load without damage until failure. The computed tomography observations confirm the load partition analysis. T2 - World Non Destructive Testing CY - München, Germany DA - 11.06.2016 KW - CT KW - Neutron diffraction KW - Aluminium KW - Composite PY - 2016 AN - OPUS4-38395 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schaupp, Thomas T1 - 3D Charakterisierung wasserstoffunterstüzter Risse in Stahl mittels Synchrotron-Refraktions-CT N2 - Die Fehlertoleranz moderner hochfester Stähle gegenüber Prozessfehlern beim Fügen nimmt stetig ab und erfordert eine immer kritischere Beurteilung der Ergebnisse aus den vorhandenen Prüfverfahren. Deren Aussagekraft ist häufig zu gering und daher muss zum einen das wissenschaftliche Verständnis der Mikrokaltriss-Entstehung in diesen Stählen vertieft werden und zum anderen müssen die Prüfmethoden und Bewertungskriterien angepasst werden. Dies erfordert ein besseres Verständnis insbesondere der Kopplung von Eigenspannungen, Wasserstoffgehalten und der Wirkung äußerer Kräfte auf die Rissentstehung und das Risswachstum. Erstmals soll mittels 3D-Synchrotron-Refraktions-Topographie an der BAMline am BESSY die Rissentstehung in mit Wasserstoff beladenen Zugproben charakterisiert werden. Diese Kenntnisse sollen in weiteren Untersuchungen auf Schweißnähte übertragen werden. T2 - MDDK – Master-, Diplomanden- und Doktorandenkolloquium CY - Universität Magdeburg, Germany DA - 23.06.2016 KW - Duplexstahl KW - Wasserstoffunterstützte Rissbildung KW - Computertomographie KW - Synchrotron-Refraktion PY - 2016 AN - OPUS4-36733 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Evsevleev, Sergei T1 - Stress-induced damage evolution in aluminum matrix composites N2 - Two metal matrix composites, both consisting of a near-eutectic cast AlSi12CuMgNi alloy, one reinforced with 15%vol. Al2O3 short fibers and the other with 7%vol. Al2O3 short fibers + 15%vol. SiC particles were studied. Distribution, orientation, and volume fraction of the different phases was determined by means of synchrotron computed tomography. The load partitioning between phases was investigated by in-situ neutron diffraction compression tests. The internal damage of the eutectic Si phase and Al2O3 fibers after ex-situ compression tests was directly observed in CT reconstructed volumes. Significant debonding between Al-matrix and SiC particles was found. Those observations allowed rationalizing the load transfer among the constituent phases of two different composites. Finally, based on the Maxwell scheme, a micro-mechanical model was utilized for the composite with one and two ceramic reinforcements. The model rationalizes the experimental data, and predicts the evolution of principal stresses in each phase. T2 - The 4th International Congress on 3D Material Science 2018 CY - Elsinore, Denmark DA - 10.06.2018 KW - Computed Tomography KW - Aluminium KW - Metal Matrix Composite KW - Load Partition PY - 2018 AN - OPUS4-45397 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bruno, Giovanni T1 - Characterization of Additive Manufacturing Materials at BAM N2 - The combination of tomographic, microstructural data with other experimental techniques and with modeling is paramount, if we want to extract the maximum amount of information on material and component properties. In particular, quantitative image analysis, statistical approaches, direct discretization of tomographic reconstructions represent concrete possibilities to extend the power of the tomographic 3D representation to insights into the material and component performance. This logic thread equally holds for industrial and academic research and valorizes expensive experiments such as those carried out at synchrotron sources, which cannot be daily repeated. I will show a few examples of possible use of X-ray tomographic data for quantitative assessment of damage evolution and microstructural properties, as well as for non-destructive testing. Examples of micro-structured inhomogeneous materials will be given, such as Composites, Ceramics, Concrete, and Additively manufactured parts. I will also show how X-ray refraction computed tomography (CT) can be highly complementary to classic absorption CT, being sensitive to internal interfaces. Additionally, I will show how Neutron Diffraction, which is extremely well suited to the study of internal stresses, both residual and under external load, can well be coupled to the microstructural framework gained by CT, allowing understanding the microstructure-property relationships in materials. Finally, I will show that BAM is very active in standardization and certification, including production of Reference Materials and Methods. T2 - Skoltech Determination of the microscopic residual stress CY - Moscow, Russia DA - 20.11.2019 KW - Additive Manufacturing KW - Computed Tomography KW - Neutron Diffraction KW - X-ray refraction techniques KW - Composites PY - 2019 AN - OPUS4-49929 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mieller, Björn T1 - Heißprägen im Grünzustand und Sinterprägen - Zwei Verfahren zur Strukturierung keramischer Folien und Laminate N2 - Prägeverfahren bieten eine interessante Alternative zur Strukturierung keramischer Folien und Laminate. Im Gegensatz zur etablierten Stanz- oder Laserbearbeitung von Einzelfolien sind damit einerseits Strukturtiefen realisierbar, die nicht einem Vielfachen der Einzelfoliendicke entsprechen, andererseits können Strukturierungsgrade erzielt werden, bei denen perforierte Einzelfolien nicht mehr handhabbar sind. Heißprägen grüner Folien und Laminate erfolgt bei Temperaturen um 130 °C mit Metallstempeln. Die plastische Verformung erfolgt zeitabhängig. Dabei sind die Fließeigenschaften des polymeren Binders der Grünfolie maßgeblich für die Konturtreue der Prägung. Randeinzug und Gründichtegradienten um den Eindruck können zu Defekten im Sintergefüge führen. Je nach Sinterverfahren muss die Schwindung der geprägten Struktur berücksichtigt werden, eine Kombination dieses Verfahrens mit zero-shrinkage Techniken ist aber möglich. Sinterprägen stellt eine Erweiterung der Drucksintertechnologie für glaskeramische Komposite dar. Dabei wird ein Pressstempel aus glasartigem Kohlenstoff während des Brandes in die erweichte Glasphase des Komposits gedrückt. Die Abformung erfolgt durch viskosen Fluss der Glasphase. Mit Kenntnis des Dichte- und Viskositätsverlaufs des Werkstoffs kann das Verfahren so gestaltet werden, dass die Pressform konturtreu abgeformt wird. Mittels Sinterprägen lassen sich auch erhabene Strukturen realisieren, wobei diese häufig eine erhöhte Porosität aufweisen. T2 - Herbstsymposium 2016 | Keramische Mehrlagentechnik - Herstellverfahren und Anwendungen CY - Erlangen, Germany DA - 30.11.2016 KW - Folientechnik KW - Keramische Substrate KW - Low temperature co-fired ceramics (LTCC) PY - 2016 AN - OPUS4-38582 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Xue, Boyang T1 - Ultrasound-Assisted Underwater Laser-induced Breakdown Spectroscopy with HighRepetition-Rate μJ-DPSS laser N2 - The elemental analysis of seawater is often critical to the understanding of marinechemistry, marine geochemistry, and the deep-sea ecosystems. Laser-induced breakdownspectroscopy (LIBS) with the advantage of rapid multi-elements detection, has a greatpotential for in-situ elemental analysis of seawater. In practice, it is crucial to create acompact, low cost and power saving instrument for the long-term deep-sea observation. Arecently appeared diode-pumped solid-state (DPSS) laser seems to be a promising candidateas it is both compact and robust. Additionally, its high repetition rate up to hundreds of kHzcan provide a considerable throughput for LIBS analysis. However, the DPSS lasers operateat moderate pulse energies, usually less than one mJ, which cannot sustain stablebreakdowns in bulk water. To ensure stable laser-induced plasmas underwater with such aμJ-DPSS laser, we introduced an ultrasound source to assist the breakdown process. Thephase interface and mass flow generated by the near-field ultrasound can greatly reduce thebreakdown threshold and enhance element-specific emissions. Meanwhile, the highrepetition-rate pulses can also improve the breakdown probability and generate uniqueemission lines originated from the water molecule. We further demonstrate that the highrepetition-rate DPSS laser combined with the Echelle spectrometer can provide effectivequantitative analysis for metal elements in bulk water. T2 - 10th Euro-Mediterranean Symposium on Laser-Induced Breakdown Spectroscopy CY - Brno, Czech Republic DA - 08.09.2019 KW - LIBS KW - Laser induced plasma KW - Plasma modeling KW - Plasma diagnostics KW - Underwater LIBS PY - 2019 AN - OPUS4-49769 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Blume, Simon T1 - Isotopic analysis of lithium via acousto-optically gated high-repetition laser-induced breakdown spectroscopy and spatial heterodyne spectroscopy N2 - Acousto-optically gating the emission signal from a laser-induced breakdown spectroscopy (LIBS) plasma negates some of the line-broadening effects, therefore, improving the signal line shape. However, the remaining influences disallow the differentiation of the contributions of the individual lithium isotopes, even when utilizing a high-resolution spatial heterodyne spectrometer (SHS). Nevertheless, isotopic analysis of lithium with LIBS is still feasible, because lithium exhibits a strong self-absorption dip in the emission signal, which is likewise characterized by the isotopic shift and even benefits from the broad emission lines typically observed in LIBS. The isotopic ration can be resolved from the absorption dip via high-resolution SHS. T2 - SciX 2024 CY - Raleigh, NC, USA DA - 20.10.2024 KW - LIBS KW - SHS KW - Isotopic analysis KW - Lithium PY - 2024 AN - OPUS4-62012 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kupsch, Andreas T1 - 3D Analysis of transport structures in realistically compressed gas diffusion layer T2 - 6th Joint BER II and BESSY II User Meeting CY - Berlin, Germany DA - 2014-12-03 PY - 2014 AN - OPUS4-32212 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kupsch, Andreas T1 - Talbot-Lau interferometry for non-destructive testing T2 - 23. Sitzung des DGZfP-Fachausschusses Zerstörunfreie Materialcharakterisierung CY - Berlin, Germany DA - 2015-11-12 PY - 2015 AN - OPUS4-34823 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mieller, Björn T1 - Druckunterstütztes Sintern von Low Temperature Co-Fired Ceramics: Einfluss der Brennhilfsmittel auf die Oberflächenqualität T2 - DKG-Jahrestagung 2014 CY - Clausthal-Zellerfeld, Germany DA - 2014-03-24 PY - 2014 N1 - Geburtsname von Mieller, Björn: Brandt, B. - Birth name of Mieller, Björn: Brandt, B. AN - OPUS4-30471 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabe, Torsten T1 - Co-Sinterung von Multilayer-Werkstoffverbunden - Möglichkeiten und Grenzen T2 - DKG-Jahrestagung 2014 CY - Clausthal-Zellerfeld, Germany DA - 2014-03-24 PY - 2014 N1 - Geburtsname von Mieller, Björn: Brandt, B. - Birth name of Mieller, Björn: Brandt, B. AN - OPUS4-30441 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bruno, Giovanni T1 - Evaluating Porosity and Properties in Diesel Particulate Filter Ceramics: a Problem to solve with Neutrons and Synchrotron Radiation T2 - Industrie Workshop HZB CY - Berlin, Germany DA - 2013-12-03 PY - 2013 AN - OPUS4-31320 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kupsch, Andreas T1 - X-ray dark field imaging T2 - 11th European Conference on Non-Destructive Testing CY - Prag, CZ DA - 2014-10-06 PY - 2014 AN - OPUS4-31918 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabe, Torsten T1 - Prozessbegleitende Prüfung beim Sintern keramischer Schichtverbunde N2 - Die zuverlässige Herstellung von Bauteilen aus Hochleistungskeramik erfordert den Einsatz von prozessbegleitenden Prüfverfahren in allen Fertigungsstufen. Prozessbegleitende Prüfung umfasst sowohl die Bewertung von Ausgangs- und Zwischenprodukten (Pulver, Suspensionen, Grünkörper) als auch die in-situ Überwachung kritischer Fertigungsstufen (Aufbereitung, Formgebung, Entbinderung, Sinterung). Der Arbeitskreis „Prozessbegleitende Prüfverfahren“ im DKG/DGM-Gemeinschaftsausschuss „Hochleistungskeramik“ bietet eine Plattform zum Informationsaustausch über neue Messverfahren und zur Initiierung von Ringversuchen und Referenzmaterialentwicklung. Als aktuelle Beispiele werden zwei applikationsnahe Verfahren zur in-situ Charakterisierung von Geometrieveränderungen (Schwindung, Verformung) an großformatigen keramischen Schichtverbunden vorgestellt. Die Hochtemperatur-3D-Laserprofilometrie ermöglicht die Visualisierung und Quantifizierung der lokalen Verformung keramischer Multilayer während der drucklosen Sinterung. Beobachtet wurden an LTCC-Multilayern starke Verformungen bereits während der Entbinderung und in der Abkühlphase. Das Wissen um zwischenzeitliche Verformungen erweitert das Verständnis über die Ursachen von Defekten in Multilayer-Bauteilen. Die in-situ Messung der Dickenschwindung an realen, großformatigen LTCC-Bauteilen während der druckunterstützten Sinterung wurde erstmals durch die Entwicklung eines LTCC-kompatiblen Drucksinteraggregat mit integriertem Dilatometer ermöglicht. Zusätzlich wurde das Drucksinteraggregat mit einer prozessbegleitende Mess- und Regelungseinrichtung für den Sauerstoffpartialdruck ausgestattet. Durch ein optimiertes Sauerstoffpartialdruckregime konnte an LTCC-Modulen eine qualitätsgefährdende Silberdiffusion aus den Leiterbahnen in das umgebende keramische Dielektrikum drastisch reduziert werden. Das mit einem industriellen Partner entwickelte Drucksinteraggregat eröffnet unikale Möglichkeiten zur Optimierung von Aufheizgeschwindigkeit, Druck und Sinteratmosphäre in allen Phasen des Sinterprozesses. T2 - Werkstoffwoche CY - Dresden, Germany DA - 27.09.2017 KW - In situ Prüfung KW - Keramische Multilayer KW - Laserprofilometrie KW - Drucksintern PY - 2017 AN - OPUS4-42297 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Palásti, Dávid jenö T1 - The effects of the laser pulse profile on the plasma emission properties N2 - Intense laser pulses create plasmas upon radiation on targets, and the properties of such plasmas are generally determined by both the properties of the target and the laser pulse. In terms of laser intensity, the irradiance and even more importantly the fluence are the critical parameters [1]. Since most lasers emit pulses of a constant pulse duration dictated by the design of the resonator and Q-switch, these two parameters are usually used interchangeably in studies. However, with the emergence of fiber laser based light sources [2], which are capable not just to freely tune the pulse duration, but to generate variable and high pulse repetition rates, up to the MHz range, a new and interesting optimization aspect is given to the laser spectroscopy community. In our study a low alloy steel standard sample (BAS 403/1) was investigated using a variable pulse duration and pulse repetition rate MOPA laser with 80W power of  = 1064 nm emission (JPT M7, VONJAN Technology GmbH, Wessling, Germany). In our experiments the laser was set to pulses with low individual energy (0.4 mJ) at 200 kHz pulse repetition rate, while the pulse duration was varied between 50 and 500 ns. The plasma emission was recorded by an LTB Demon spectrometer in several spectral regions, which included iron, chromium and manganese lines. Utilizing the variable pulse duration of this laser source, it was possible to assess the effects of changing the fluence, while the irradiance was kept at the same value. Among the investigated parameters are the emission intensity, peak width and self-absorption characteristics of major and minor components, as well as the plasma temperature. While the effects for the peak intensity are quite well correlated with the fluence, its interplay with other peak parameters appear to be more complicated. T2 - AMACEE 2025 CY - Brno, Czech Republic DA - 26.08.2025 KW - LIBS KW - Fiberlaser KW - Plasma properties PY - 2025 AN - OPUS4-64218 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Riesemeier, Heinrich T1 - Combined synchrotron X-ray and neutron imaging for the characterization of fuel cells T2 - Third Joint BER II and BESSY II Users´ Meeting CY - Berlin, Germany DA - 2011-11-30 PY - 2011 AN - OPUS4-25125 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tötzke, C. T1 - Synchrotron tomographic study on the inhomogeneous compression of gas diffusion layers in fuel cells T2 - 10th Symposium on Fuel Cell and Battery Modelling and Experimental Validation - ModVal 10 CY - Bad Boll, Germany DA - 2013-03-19 PY - 2013 AN - OPUS4-28078 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tötzke, Chr. T1 - 3D Analysis of transport structures in realistically compressed gas diffusion layers T2 - HZB User Meeting 2013 CY - Berlin, Germany DA - 2013-12-04 PY - 2013 AN - OPUS4-17666 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mieller, Björn T1 - Druckgesinterte LTCC-Substrate für die Dünnfilmbeschichtung T2 - DKG-Jahrestagung 2011 CY - Saarbrücken, Germany DA - 2011-03-28 PY - 2011 N1 - Geburtsname von Mieller, Björn: Brandt, B. - Birth name of Mieller, Björn: Brandt, B. AN - OPUS4-23490 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kupsch, Andreas T1 - Direct X-Ray Refraction of Microstructures T2 - HZB User Meeting CY - Berlin, Germany DA - 2013-12-04 PY - 2013 AN - OPUS4-26611 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bruno, Giovanni T1 - Bewertung von Porositätsparametern in Cordierit-Diesel-Partikelfilter-Materialien mit fortgeschrittenen Röntgenverfahren und statistischer Analyse T2 - DGZfP-Jahrestagung 2014 CY - Potsdam, Germany DA - 2014-05-26 PY - 2014 AN - OPUS4-30843 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bruno, Giovanni T1 - Evaluating Porosity in Cordierite Diesel Particulate Filter Materials: Advanced X-ray and new Statistical Analysis Methods T2 - 11th European Conference on Non-Destructive Testing CY - Prag, CZ DA - 2014-10-06 PY - 2014 AN - OPUS4-31916 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Bernd R. T1 - Synchrotronstrahlung: verbesserte Refraktions- und Absorptions Mikro-CT für die zerstörungsfreie Materialcharakterisierung T2 - DACH Jahrestagung 2015 CY - Salzburg, Austria DA - 2015-05-11 PY - 2015 AN - OPUS4-33685 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mieller, Björn T1 - New Setter Materials for the Pressure-Assisted Sintering of Low Temperature Co-Fired Ceramics T2 - 14th International Conference of the European Ceramic Society - ECERS 2015 CY - Toledo, Spain DA - 2015-06-21 PY - 2015 N1 - Geburtsname von Mieller, Björn: Brandt, B. - Birth name of Mieller, Björn: Brandt, B. AN - OPUS4-33568 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Plotnikov, Alexei T1 - Application of glow discharge mass spectrometry with "fast flow" source to the determination of impurities in refined magnesium using pressed powder samples T2 - Euroanalysis 2013 CY - Warsaw, Poland DA - 2013-08-25 PY - 2013 N1 - Geburtsname von Mieller, Björn: Brandt, B. - Birth name of Mieller, Björn: Brandt, B. AN - OPUS4-30356 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mieller, Björn T1 - Druckunterstützendes Sintern glaskeramischer Komposite mit Opferfolie aus hexagonalem Bornitrid T2 - 90. Jahrestagung der Deutschen Keramischen Gesellschaft (DKG) CY - Bayreuth, Deutschland DA - 2015-03-15 PY - 2015 N1 - Geburtsname von Mieller, Björn: Brandt, B. - Birth name of Mieller, Björn: Brandt, B. AN - OPUS4-32851 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bruno, Giovanni T1 - Evolution of microcrack density under tensile loading in ß-eucryptite T2 - MRS Fall Meeting CY - Boston, MA, USA DA - 2015-11-29 PY - 2015 AN - OPUS4-35169 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Recknagel, Christoph T1 - SENSO JOINT - An innovative sensor for suitable joint design N2 - Inacceptable capability and durability of joint sealing systems but also inadequate traffic performance (noise emission; overrolling comfort) up to traffic safety aspects reflect the still enormous demand for data-based description of concrete pavements performance under heavy loading conditions. Especially the deformation behavior of concrete pavement slabs in the joint region in consideration of new pavement construction types and improved concrete mixtures meanwhile established but also under the steeply rising traffic loads is not sufficiently explored. To create a data basis for advanced design rules, evaluation methods and product standards - and with it to improve quality, durability and finally sustainability of pavements - an innovative 3-D sensor system SENSO JOINT adapted to german roadworking requirements and suitable for heavy-duty operating conditions was developed. The contribution introduced describes the development of an extensive technical solution based on the analysis of decisive loads, interactions and boundary conditions. Based on calibration data, results of laboratory testing and finally field-testing on different concrete pavement construction types the outcome of a multi-level evaluation process shall introduce the potential of the new sensor system. T2 - 9th International Conference on Maintenance and Rehabilitation of Pavements (MAIREPAV 2020) CY - Online meeting DA - 01.07.2020 KW - Concrete pavements KW - Sustainable joint sealing KW - Load quantification KW - innovative measurement technology KW - Field validation KW - Performance design for joint systems PY - 2020 AN - OPUS4-51926 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hirsch, Philipp Daniel T1 - Inspection with multisensor laser thermography N2 - The automated testing of complex, highly stressed components requires advanced methods capable of detecting various forms of defects with precision and reliability. In this work we present our approach by combining robotic automation with laser thermography, as a versatile and efficient solution for inspecting intricate geometries under demanding industrial conditions. Central to this approach is the integration of a fiber-coupled laser as a flexible heat source, a high-performance thermal imaging system, an industrial robot, additional visible camera systems, different IR emitters and intelligent signal processing algorithms. This allows, after an initial fully-automated mapping of the part geometry and position that the object under test is thermographically tested for surface or bulk defects. Interferences caused by unideal surface conditions can be corrected for using simultaneously obtained optical images. Finally, all test results can be mapped onto a digital representation of the object leading to a fully digital and machine-readable documentation that can be used for quality assurance. This combination therefore enables accurate defect detection and characterization, overcoming traditional limitations associated with material variability and surface inhomogeneities. The system's adaptability allows for tailored solutions that address real-world challenges, ensuring reliable and repeatable results across diverse applications. The proposed methodology emphasizes the synergy between robotics, active thermography, and advanced data analysis to achieve high levels of precision and automation. This work highlights the potential of these technologies to optimize quality assurance processes and contribute to innovation in various industrial sectors. T2 - Pan-American Conference for Nondestructive Testing (VIII PANNDT) CY - Niagara Falls, Kanada DA - 09.06.2025 KW - ZFP4.0 KW - Automatisation KW - Crack detection KW - Laser KW - Thermography KW - Robot PY - 2025 AN - OPUS4-63646 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Breese, Philipp Peter T1 - Thermographic Methods for In-situ Monitoring of Metal-based Additive Manufacturing Processes N2 - Additive manufacturing (AM) with metals creates new, exciting opportunities for industrial applications. Especially industries with high relevance for the future like transport and energy benefit from optimized designs and novel materials. However, a reliable in-situ quality assurance for metal AM is still missing while process optimization is slow. This directly hinders the huge potential of metal AM technologies. A promising method to counteract this issue is the investigation of the emitted thermal radiation. It is optimal for monitoring and understanding the thermal history of the high-temperature AM process. The thermal history holds virtually all information about the properties and the quality of the manufactured components. The thermal information is also highly valuable for tuning and validating numerical simulations to gather further insights into the process. Despite this importance, the usage of thermal radiation in commercial AM machines is only marginal (like simple pyrometry or long-time exposure for optical tomography (OT) at a single wavelength). Based on this deficit and potential, this work gives an overview of the research in division “8.3 Thermographic Methods” at the Bundesanstalt für Materialforschung und -prüfung (BAM) in Berlin, Germany. Different wavelengths of the thermal radiation are investigated: the visible range (VIS), the short-wave infrared (SWIR), and the mid-wave infrared (MWIR) with their respective optimal field of application. Focus lies on laser powder bed fusion of metals (PBF-LB/M), but directed energy deposition with laser beam (DED-LB/M) is investigated as well. The presented research is performed not only on commercial AM machines, but also on an in-house developed PBF-LB/M research system specifically designed for sensor testing. This ensures an exciting mélange of applied research for industrial applications, and fundamental research for process understanding and validation. Therefore, a crucial contribution to industrial and scientific insights of metal AM is given. T2 - Sim-AM 2025 CY - Pavia, Italy DA - 09.09.2025 KW - Laser powder bed fusion KW - Direct energy deposition KW - Quality assurance KW - Infrared thermography PY - 2025 AN - OPUS4-65391 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Breese, Philipp Peter T1 - Klein, heiß und schnell: Bestimmung von Realtemperaturen in der metallbasierten additiven Fertigung mittels hyperspektraler Thermografie N2 - Die additive Fertigung von Metallen mittels Laser Powder Bed Fusion (PBF LB/M) ermöglicht die Herstellung komplexer Geometrien und die Nutzung neuartiger Legierungen. Die dabei lokal im Prozess auftretenden Temperaturverteilungen beeinflussen maßgeblich die Bauteileigenschaften sowie die Entstehung von Defekten wie bspw. Risse und Poren. Eine quantitative Bestimmung der Realtemperaturen ist daher essenziell für Prozessvalidierung und -vergleich sowie die Qualitätssicherung und das Verständnis der zugrunde liegenden physikalischen Vorgänge. Bisherige thermografische Monitoring-Ansätze liefern jedoch meist nur qualitative Informationen. Hintergrund sind die Herausforderungen gegeben durch den Prozess: kleine Schmelzbäder (< 300 µm), hohe Temperaturen (> 2500 K) und hohe Scangeschwindigkeiten (ca. 1 m/s). Zusammen mit den dynamischen Änderungen des Emissionsgrads u.a. durch Phasenübergänge ergeben sich äußerst schwierige Bedingungen für thermografische Messungen. Um dieser Herausforderung zu begegnen, verfolgen wir einen neuartigen Ansatz zur hyperspektralen Thermografie, der eine simultane Messung der emittierten Strahlung im kurzwelligen Infrarotbereich (1 bis 1,6 µm) entlang einer Linie bei ca. 20 kHz ermöglicht. Durch die Bewegung des Schmelzbades senkrecht durch die Messlinie kann ein typisches Schmelzbad rekonstruiert werden. Die Temperatur-Emissionsgrad-Separation (TES) erlaubt dabei die Bestimmung von Realtemperaturen und Emissionsgraden basierend auf parametrisierten spektralen Emissionsgradfunktionen sowie radiometrischen Kalibrationen. Die Umsetzung erfolgt an der Forschungsmaschine der BAM „SAMMIE“, die speziell für thermografische Messungen am PBF LB/M-Prozess konzipiert wurde. Die Ergebnisse zeigen das Potenzial der hyperspektralen Thermografie zur Erfassung von Realtemperaturen im Prozess. Dies stellt einen wichtigen Schritt zur verbesserten Vergleichbarkeit und Wiederholbarkeit der Fertigung sowie zur Validierung komplexer Simulationen dar. Damit trägt der neuartige Ansatz langfristig zur Erhöhung der Sicherheit und des Verständnisses additiver Fertigungsprozesse bei. T2 - Thermo 25 CY - Garching bei München, Germany DA - 12.11.2025 KW - Laser powder bed fusion KW - Infrarot Thermografie KW - In-situ Monitoring KW - Qualitätssicherung KW - Temperaturmessung PY - 2025 AN - OPUS4-65394 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Spitzer, Stefan T1 - Comparative Study on Standardized Ignition Sources Part 2: Exploration of the Initial Igniting Volume of Standardized Ignition Sources for the Determination of Explosion Characteristics N2 - There are several standardized ignition sources in use for the determination of explosion characteristics of gases, vapors and dusts. In the standards the ignition source is stated, but they vary in stating other characteristics like burning duration, energy or burning volume. Since heat is not visible under normal circumstances a Schlieren-Technique was used to make the full heating volume and not just the flames visible. While an earlier paper of the authors focused on the ignition energy and burning duration of four standardized ignition sources, this paper focuses on the initial igniting volume, the ratio between initial igniting volume and the test-vessel size and other phenomena that were observed with the Schlieren-Technique. T2 - Loss Prevention CY - Prague, Czech Republic DA - 06.06.2022 KW - Ignition source KW - Hybrid Mixtures KW - 20L-sphere PY - 2022 AN - OPUS4-55029 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Spitzer, Stefan A1 - Recknagel, Christoph T1 - INFUSE - SensoJoint Entwicklung neuartiger Sensormethodik N2 - Funktionsschema einer neuartigen Messmethodik zur Ermittlung realer Beanspruchungen von Fugensystemen in hochbeanspruchten Betonfahrbahnbelägen. T2 - Bund-Länder Forschungskolloquium CY - Berlin, Germany DA - 05.07.2017 KW - Dauerhaftigkeit KW - Betonfahrbahndecke KW - Fugenproblematik PY - 2017 AN - OPUS4-41248 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna A1 - Hodoroaba, Vasile-Dan T1 - CUSP inter-laboratory comparisons N2 - In this breakout session first, an introduction is given on the planning and organisation of an inter-laboratory comparison (ILC) under the pre-standardisation plattform VAMAS within the newly formed technical working area TWA 45 Micro and Nano Plastics in the Environment. An update with the ILCs on micro- and nanoplastic performed so far is also given. In the third part, the requirements for a reference materials are presented. The needs from the different H2020 micro- and nanoplastic projects are collected and compiled in an ILC matrix for joint activities as the next steps. T2 - The European Research Cluster to Understand the Health Impact of Micro- and Nanoplastics (CUSP) Launching Event CY - Online meeting DA - 10.06.2021 KW - Microplastic KW - Nanoplastic KW - Inter-laboratory comparison KW - VAMAS KW - Reference material PY - 2021 AN - OPUS4-52808 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bhadeliya, Ashok T1 - High Temperature Fatigue Crack Growth in Nickel-Based Alloys Refurbished by Additive Manufacturing and Brazing N2 - Hybrid additive manufacturing plays a crucial role in the restoration of gas turbine blades, where e.g., the damaged blade tip is reconstructed by the additive manufacturing process on the existing blade made of a parent nickel-based alloy. However, inherent process-related defects in additively manufactured material, along with the interface created between the additively manufactured and the cast base material, impact the fatigue crack growth behavior in bi-material components. This study investigates the fatigue crack growth behavior in bi-material specimens of nickel-based alloys, specifically, additively manufactured STAL15 and cast alloy 247DS. The tests were conducted at 950 °C with stress ratios of 0.1 and -1. Metallographic and fractographic investigations were carried out to understand crack growth mechanisms. The results revealed significant retardation in crack growth at the interface. This study highlights the potential contributions of residual stresses and microstructural differences to the observed crack growth retardation phenomenon, along with the conclusion from an earlier study on the effect of yield strength mismatch on crack growth behavior at a perpendicular interface in bi-material specimens. T2 - Superalloys 2024 Conference CY - Champion, PA, USA DA - 08.09.2024 KW - Fatigue crack growth KW - Bi-material structure KW - Nickel-based alloys KW - Additive Manufacturing KW - Brazing PY - 2024 AN - OPUS4-61047 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hörenz, Christoph T1 - Improved Sample Preparation for the Analysis of Nanoparticles by Electron Microscopy N2 - Various promising sample preparation procedures aiming to avoid drying artifacts and guarantee homogeneously distributed NP samples for imaging techniques like TEM, SEM or AFM are presented. This involves retarded drying in an environment of high relative humidity as well as spin coating or freeze drying of the sample on the substrate. Depending on the type of the NPs, different techniques are successful in obtaining homogenous sample deposition. Simple drying at ambient conditions often results in heavily agglomerated NPs densely packed in coffee ring traces. Retardation of the drying speed in an environment of high relative humidity, however, yields homogeneous NP deposition in the case of bimodal SiO2 and bimodal gold NP’s. In contrast, a sample of bipyramidal TiO2, heavily agglomerated when commonly dried, is successfully dispersed by spin coating the suspension on the substrate. The analysis of the particle size distribution of the bimodal silica and gold samples yielded number ratios resembling the nominal number ratios. The reliable measurement of the NP concentration of polydisperse samples by electron microscopy, even if relative, is new and of special relevance because up to now only the size of the particles, i.e. the abscissa of the PSD, can be measured reliably. T2 - EMPIR nPSize Training Course "Metrology for Measurement of Nanoparticle Size by Electron Microscopy and Atomic Force Microscopy" CY - Online meeting DA - 27.10.2020 KW - Nanoparticles KW - Particle size distribution KW - Sample peparation KW - Electron microscopy PY - 2020 AN - OPUS4-51716 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jaunich, Matthias T1 - Tieftemperaturverhalten von Elastomerdichtungen - Randbedingung für den Einsatz in Transport- und Lagerbehältern für radioaktive Stoffe T2 - Polymerwissenschaftliches Seminar, BAM CY - Berlin, Germany DA - 2009-06-18 PY - 2009 AN - OPUS4-19568 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zaghdoudi, Maha T1 - Numerical modelling of compression stress relaxation and compression set of elastomer O-rings during aging N2 - Elastomer seals are used in many industrial applications due to their excellent mechanical properties at a wide range of temperatures. Their high versatility and recovery potential under several load conditions make them well suitable for the application in containers designed for transport, storage and/or disposal of radioactive materials. In containers for low and intermediate level radioactive waste, elastomer seals are used as barrier seals, and as auxiliary seals in storage and transportation casks (dual purpose casks) for heat generating radioactive waste, such as spent fuel and high-level waste. While a seal exchange at defined intervals is typical in many conventional applications, it is impossible or at least hard to perform when principles of minimization of radiation exposure have to be considered and prohibit an unnecessary cask handling. An extensive knowledge of the change of the elastomer’s properties during aging and the availability of reliable end-of-lifetime criteria to guarantee the permanent safe enclosure of the radioactive material is mandatory. As BAM is involved in most of the national cask licensing procedures and in the evaluation of cask-related long-term safety issues, great efforts have been already made and are still planned to scientifically support this task. Compression stress relaxation and compression set were identified as key indicators of elastomer long-term performance and quantitatively investigated in comprehensive test programs. Among other representative types of elastomers, specimens made from ethylene propylene diene rubber (EPDM) were tested before, during and after aging to capture the most important of their complex mechanical properties. In the presented study, exemplary results were used to simulate the compression stress relaxation and the compression set of elastomer O-rings during aging. Regarding the influence of temperature, the time temperature superposition principle is applied in the relaxation analysis of elastomer O-rings. The proposed model is implemented in the commercial finite element software ABAQUS/Standard® [1] with a sequential temperature displacement coupling. Numerical results match the experimental compression stress relaxation measurements well. The prediction of compression set values after long-term aging shows a relatively good agreement with the experimental results. Nevertheless, all input parameters derived from the specimen tests, additional assumptions concerning boundary conditions and modeling strategy are discussed with regard to the identified slight discrepancies. The possibility to extend the finite element model to represent the O-ring seal’s ability to recover after a (fast) partial release is taken into account T2 - ASME 2020 Pressure Vessels & Piping Conference (PVP2020) CY - Online meeting DA - 03.08.2020 KW - Stress relaxation KW - Ageing KW - Compression Set KW - O-ring KW - Sequential analysis KW - Simulation PY - 2020 AN - OPUS4-52135 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Charmi, Amir T1 - Virtual-lab-based determination of a macroscopic yield function for additively manufactured parts N2 - This work aims for an yield function description of additively manufactured (AM) parts of S316L steel at the continuum-mechanical macro-scale by means of so-called virtual experiments using a crystal plasticity (CP) model at meso-scale. Additively manufactured parts require the consideration of the specific process-related microstructure, which prevents this material to be macroscopically treated as isotropic, because of crystallographic as well as topological textures. EBSD/CT-Scans from in-house additively manufactured specimen extract the unique microstructural topology which is converted to a representative volume element (RVE) with grain structure and crystal orientations. Crystal plasticity model parameters on this RVE are calibrated and validated by means of mechanical testing under different texture angles. From virtual experiments on this RVE, yield loci under various loading conditions are simulated. The scale bridging from meso- to macro-scale is realised by the identification of the simulated yield loci as a modified anisotropic Barlat-type yield model representation. T2 - The First European Conference on Structural Integrity of Additively Manufactured Materials (ESIAM19) CY - Trondheim, Norway DA - 09.09.2019 KW - Virtual experiments KW - Additive manufacturing KW - Anisotropy KW - Crystal plasticity KW - Scale-bridging PY - 2019 AN - OPUS4-49376 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rockenhäuser, Christian T1 - Microstructural characterisation of ageing and creep of 2618A N2 - Presentation of microstructural characterisation results for alloy 2618A T2 - Projektausschusssitzung mit Industrivertretern der Forschungsvereinigung Verbrennungskraftmaschinen (FVV) CY - Frankfurt a. M., Germany DA - 07.04.2016 KW - Dark-field transmission electron microscopy (DFTEM) KW - 2618A KW - S-Phase KW - Coarsening KW - Microstructure PY - 2016 AN - OPUS4-36705 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jaunich, Matthias T1 - Elastomer seals - overview and development N2 - The talk summarizes the current and future investigations of elastomer seal materials in division 3.4. T2 - IRSN-BAM Symposium Safety of Transport and Storage Packages CY - Online meeting DA - 19.11.2020 KW - Seal KW - Degradation KW - Ageing PY - 2020 AN - OPUS4-51751 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sagradov, Ilja T1 - Long-term tests and numerical simulations on metal seals based on continuous force measurement in compressed state N2 - In Germany, the search for a disposal site for heat-generating radioactive waste will take decades longer than originally assumed. Transport and storage casks must therefore ensure safe containment for extended interim storage periods, possibly over 100 years. In order to maintain the required leak tightness, spring core metal seals with aluminum or silver cladding are used. As sealing force decreases over time, BAM has been conducting tests for over 15 years to prove their long-term reliability. This work - a joint project of BASE and BAM - aims to obtain additional material data using a new device for continuous measurement of compression force over time and temperature for lifetime prediction models and is supported by FEM simulations. Initial tests on aluminum and silver seals have been completed, and first results are presented. T2 - safeND 2025 CY - Berlin, Germany DA - 17.09.2025 KW - Interim storage KW - Metal seal KW - Restoring force PY - 2025 AN - OPUS4-64991 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heilmann, Maria A1 - Hodoroaba, Vasile-Dan T1 - Project 15 Measurement of particle size and shape distribution of bipyramidal titania including deposition from liquid suspension N2 - The progress in the VAMAS Project #15" Measurement of particle size and shape distribution of bipyramidal titania including deposition from liquid suspension" within TWA 34 Nanoparticle Populations is presented with highlight of the following points: - Determine and compare particle size and shape distribution by means of: • electron microscopy (SEM, TEM, STEM-in-SEM) • atomic force microscopy (AFM) • small angle X-ray scattering (SAXS) - Determine uncertainty induced by deposition protocol from liquid suspension with comparison to known values from a prior ILC with already deposited nanoparticles on TEM grids. - Provide comparative validation of protocols for the techniques other than TEM. T2 - VAMAS Regional Workshop 2023 CY - Online meeting DA - 24.01.2023 KW - Nanoparticles KW - VAMAS KW - Electron microscopy KW - AFM KW - SAXS KW - TiO2 PY - 2023 UR - https://www.bam.de/Content/EN/Events/2023/2023-01-24-vamas-regional-workshop.html AN - OPUS4-57220 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grelle, Tobias T1 - Creep Investigations on Aluminum Seals for Application in Radioactive Waste Containers N2 - In Germany spent nuclear fuel (SNF) and high level radioactive waste (HLW) are stored in interim storage containers with double lid systems. Those lids are equipped with metal seals (e.g. Helicoflex®) that ensure the safe enclosure of the inventory. Being licensed for up to 40 years of interim storage the evaluation of the long-term behavior of the seals is necessary, taking into account storage conditions, decay heat and possible mechanical loads. T2 - International Conference on Aluminum Alloys CY - Montreal, Canada DA - 17.06.2018 KW - Metal seal KW - Creep KW - Long-term behavior PY - 2018 AN - OPUS4-45843 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hodoroaba, Vasile-Dan T1 - Need for Large-Area EDS Detectors for Imaging Nanoparticles in a SEM Operating in Transmission Mode T2 - Microscopy and Microanalysis M&M 2014 CY - Hartford, CT, USA DA - 2014-08-02 PY - 2014 AN - OPUS4-31469 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bresch, Harald A1 - Unger, Wolfgang A1 - Schulte, Petra T1 - Nanotechnologie Aktivitäten der BAM N2 - Die Präsentation gibt einen Überblick über die verschiedenen Aktivitäten der BAM im Bereich der Nanotechnologie mit den Schwerpunkten Nanopartikel und Nanosicherheit. Es wird sowohl die Transportsicherheit, als auch die Sicherheit von Batterien mit Nanopartikeln angesprochen. Verschiedene BAM-Projekte zum Thema Nano werden vorgestellt, beginnend mit relevanten REFOPlanprojekten über die Erstellung der OECD nanoTG110 bis hin zu EU-Projekten zur Standardisierung von Messungen an Nanomaterialien, hier insbesondere AEROMET, NanoDefine, NanoValid und EC4SafeNano. T2 - Nano-Behördenklausur der Bundesoberbehörden CY - Berlin, Germany DA - 02.11.2017 KW - Nano KW - Nanotechnologie KW - Nanopartikel KW - Nanosicherheit KW - Nanoanalytik PY - 2017 AN - OPUS4-42793 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mrkwitschka, Paul T1 - Morphological Analysis of Graphene Oxide by SEM and Correlative Field-Flow Fractionation Coupled with Multi-Angle Light Scattering N2 - Since the first free-standing monolayer graphene sheet was successfully prepared in 2004 [1], graphene and graphene oxide materials achieved the necessary technical readiness level to be considered for use in commercial products. Moreover, the focus has shifted from fundamental research towards expanding the applicability of graphene-related 2D materials (GR2M) and to improve their competitiveness with established materials [2]. Significant advances have been made especially in applications regarding optoelectronics, energy storage materials, chemical additives, sensor applications etc. [3]. Composite products containing graphene and functionalized graphene such as inks and dyes have shown enhanced performance regarding longevity, wettability, and can be tailored for specific purposes through dedicated functionalization. For accurate physico-chemical characterization, GR2M products in their raw form or as part of composites present challenges in terms of sample preparation, choice of analytical method and evaluation of data. For instance, in the context of imaging, these challenges encompass: (a) the selection of images magnifications being representative for all the flakes ranging in size from hundreds of nanometers to micrometers; (b) the selection of representative flakes for adequate statistics, which may involve the separation of overlapping/agglomerating flakes by segmentation; and (c) the classification of diverse morphologies such as irregularly shaped/crumpled flakes, porous flakes and particulate features present in the sample. The complexity of the analytical task has needed the introduction of specific ontology for 2D materials to identify the proper descriptors characterizing confidently the morphological features of interest. Regarding light scattering techniques such as Dynamic Light Scattering (DLS) and Multi-Angle Light Scattering (MALS) commonly used for process control in industry as a first measure, an alternative approach would be necessary. This is in part due to the use of the standard sphere-model for 2D materials as appearing to be inappropriate, whilst a disc-shape model potentially yields more suitable results. Standardization efforts are underway to establish a baseline for accurate characterization of aimed measurands with sufficient statistics. To date, the measurement methods recommended by standardization bodies for the morphological-structural characterization of GR2M’s are AFM, Raman Spectroscopy and SEM and/or TEM. The acquisition of statistically relevant numbers of flakes for a thorough characterization using TEM and AFM is particularly time-consuming. The size distribution of graphene oxide- and graphene-containing inks was investigated by using a correlative approach coupling Centrifugal Field-Flow Fractionation (CF3) [4] with MALS. Up to now, promising results for Field-Flow Fractionation have been achieved only with respect to the separation into size classes of GO samples as well as of graphene oxide mixed with graphene by Asymmetrical Field-Flow Fractionation (AF4) [5], [6]. Besides the online characterization by MALS, the eluting size fractions obtained by CF3 were also collected and subsequently measured by SEM. Successful separation into size fractions allows us to apply ensemble techniques such as MALS to samples that were previously not measurable according to best-practices. In this study, the following material sub-classes have been observed with SEM: (i) nano-graphite mixed with graphene flakes, (ii) graphene oxide few- and multi-layer flakes with diverse and highly complex morphology, and (iii) graphene oxide of well-defined size and shape with >95% single- and bilayer content were investigated. Data on the class size ranges was obtained by MALS after separation with CF3 and consideration of a disc-shape model. Significant effort was invested into the sample preparation for CF3 measurements to achieve a recovery rate of >80%, well above the recommended 70% by ISO/TS 21362:2018 for validation purposes. The material fractions collected after the CF3 measurement were separately deposited on a silicon wafer and the size results of the SEM analysis were correlated with the corresponding mean sizes obtained with MALS. T2 - Microscopy and Microanalysis 2025 CY - Salt Lake City, UTAH, USA DA - 27.07.2025 KW - Advanced Material KW - CF3 KW - SEM KW - Morphology PY - 2025 AN - OPUS4-64084 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Singh, Shobhit T1 - Accelerated Creep Testing in High- Temperature Alloys N2 - This study introduces an innovative method for efficiently determining the creep properties of high-temperature materials through high-throughput testing, employing digital image correlation [1,2]. The focus is on the AlCoCrFeNiTi alloy [3-5], synthesized by directional solidification, known for its exceptional strength and unique properties. Experimental investigations, including compression, and bending creep tests, were conducted at 750°C. Capitalizing on the inhomogeneous stress and strain distribution within a cantilever subjected to bending, we leverage this characteristic to extract multiple creep curves from a single test. Stresses at key points were determined using existing analytical solutions [5,6]. Uniaxial tests spanning 300 to 500 MPa initial stress were complemented by bending tests designed to induce similar stress levels. A detailed comparison between bending and uniaxial creep is presented, including the results of verification studies on additional alloys. This methodology not only expedites testing but also minimizes material usage, energy consumption, and manual labour. This research showcases a reliable and time-efficient approach to exploring the creep behavior of high-temperature materials. The technique is particularly advantageous for characterizing precious alloys with limited dimensions. Microstructural heterogeneity may exist in specimens tested under bending load, however, it can still be correlated to the mechanical properties with modern high-resolution characterization methods. Stress and resulting strain can be directly compared in a single specimen, ensuring uniform manufacturing, and heating history. This method eliminates the possible errors due to testing with different rigs, which could impair the accuracy of studies based on individual tests. T2 - International Conference on Creep and Fracture of Engineering Materials and Structures CY - Bengaluru, KA, India DA - 28.07.2024 KW - Digital Image Correlation KW - Creep KW - High-Temperature Materials PY - 2024 AN - OPUS4-60925 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Skrotzki, Birgit T1 - Einfluss der Verformung bei hoher Temperatur auf Alterungsvorgänge in technischen Legierungen N2 - Es wird der Einfluss der Verformung bei hoher Temperatur (z.B. Kriechen) auf die Alterungsvorgänge ausscheidungsgehärteter Aluminium- und Nickelbasis-Superlegierungen vorgestellt. T2 - DGM-Tag 2016 CY - Darmstadt, Germany DA - 26.09.2016 KW - Alterung KW - Kriechen KW - Ausscheidungen KW - Vergröberung PY - 2016 AN - OPUS4-37624 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kraehnert, R. T1 - Porosity of highly porous thin films studied by X-rays at SEM T2 - 27. Deutsche Zeolith-Tagung CY - Oldenburg, Germany DA - 2015-02-25 PY - 2015 AN - OPUS4-32933 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ávila Calderón, Luis T1 - Ermüdungsverhalten und Versagensmechanismen von additiv mittels LPA hergestelltem TiAl6V4 N2 - Die Untersuchung und Charakterisierung der Entwicklung/Änderung der Mikrostruktur, der mechanischen Eigenschaften sowie der Lebensdauer additiv gefertigter metallischer Werkstoffe hat bisher, vor allem im Hinblick auf die komplexe Belastungsfälle bei sicherheitsrelevanten Anwendungen, mit der rasanten Entwicklung der Fertigungstechniken nicht Schritt gehalten. Im Rahmen dieser Arbeit wurde eine Charakterisierung des Ermüdungsverhaltens von additiv gefertigten TiAl6V4 im Low-Cycle-Fatigue Bereich (niederzyklische Ermüdung) nach Norm ISO 12206 mit Dehnungsamplituden von 0.3 bis zu 1.0 % und bei Raumtemperatur, 250°C und 400°C durchgeführt. Die TiAl6V4 Proben wurden aus zylindrischen Halbzeugen gefertigt, welche durch Laser-Pulver-Auftragsschweißen mit einer optimierten Aufbaustrategie hergestellt wurden. Die optimierte Aufbaustrategie beinhaltet variierende Spurüberlappungsgraden, die die Fertigung der dünnen zylindrischen Körper ohne weitere Ausgleichslagen ermöglicht. Das Werkstoffverhalten wird anhand von Wechselverformungskurven sowie einer Darstellung der Lebensdauer in einem Wöhler-Diagramm beschrieben. Ein Fitting der Lebensdauer-Daten erfolgt anhand der Manson-Coffin-Basquin Beziehung. Eine Eingangscharakterisierung der mikrostrukturellen Merkmale inklusive Bindefehler aus dem Herstellungsprozess wird durch Lichtmikroskopie und hochauflösende Computertomographie (CT) durchgeführt. Der Versagensmechanismus während der Belastung wird anhand von Zwischenuntersuchungen mit CT und einem unterbrochenen Versuch mit ausgewählten Versuchsparametern beschrieben. Nach dem Versagen wurden die Proben am REM, mit Lichtmikroskopie und mit CT fraktographisch in Längs- und Querrichtung untersucht. Die erfassten Lebensdauern sind ähnlich zu denen aus herkömmlichen Studien und liegen unter derjenigen von dem konventionell hergestellten (geschmiedeten) Werkstoff. In dieser Arbeit wurden für den untersuchten Werkstoff bei anwendungs- und sicherheitsrelevanten Belastungszuständen (hohe Temperaturen, zyklische Plastizität) neue experimentelle Daten und Kennwerte ermittelt und Verständnis über das mechanische Verhalten und die Entwicklung der Mikrostruktur aufgebaut. Darüber hinaus wurde Verständnis über die Rolle von Bindefehlern und anderen typisch für AM auftretenden Gefügemerkmalen auf das Versagensverhalten von DED-L TiAl6V4 gewonnen. T2 - DGM Fachausschuss Titan CY - Liebherr-Aerospace Lindenberg GmbH, Germany DA - 12.11.2019 KW - LCF KW - Titan KW - Ti-6Al-4V KW - Ti64 KW - TiAl5V4 KW - Additive Fertigung KW - CT KW - Mikrostruktur KW - Zugeigenschaften KW - Low Cycle Fatigue PY - 2019 AN - OPUS4-49758 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hodoroaba, Vasile-Dan T1 - Future projects in Microbeam Analysis better Prepared within VAMAS N2 - The presentation points out and discusses potential future projects on microbeam analysis which shall benefit from the pre-standardisation platform VAMAS (Versailles Project on Advanced Materials and Standards) which is basically related to Organisation and participation in international inter-laboratory comparisons. Ideas and strategies of better synergies between VAMAS and ISO projects (including promotion and a dedicated liaison) are discusssed. T2 - 26th Plenary Meeting of ISO/TC 202 Microbeam Analysis CY - Hangzhou, China DA - 23.10.2019 KW - Standardisation KW - Microbeam analysis KW - VAMAS KW - Pre-standardisation PY - 2019 AN - OPUS4-49443 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -