TY - CONF A1 - Duffner, Eric A1 - Wang, Bin A1 - Kriegsmann, Andreas T1 - WP8 RCS standardisation work, Probabilistic safety assessment & statistic N2 - Achievements within WP8 in the TAHYA Project during the first 18 month, including ongoing work and next steps. Including safety definition, introduction to probabilistic Approach, failure rate, consequence and risk Definition, introduction monte-carlo-Simulation. T2 - TAHYA Midterm review meeting CY - Brüssel, Belgium DA - 26.09.2019 KW - TAHYA project PY - 2019 AN - OPUS4-49191 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Frei, Vivian T1 - Characterizing the Fatigue Behavior of High-Performance Concrete for Wind Energy Structures N2 - Severe mechanical fatigue conditions for worldwide proliferating windfarms are a Major challenge for high-performance concrete in towers, connecting joints and foundations of wind turbines. High-performance concrete offers potential for the application in offshore windfarms, not only regarding its good mechanical, but also chemical resistivity due to low diffusivity in the highly densified microstructure. For a more reliable fatigue assessment, monitoring based on nondestructive testing can be a valuable complement to design rules. Both approaches demand reliable experimental data, information about scalability and the development of standardized testing methods. This article presents results of an ongoing research program of BAM (Bundesanstalt für Materialforschung und -prüfung), which is a part of a joint national project (WinConFat) funded by the German Federal Ministry for Economic Affairs and Energy. The subproject implemented by BAM examines the fatigue behavior in dependence of size and slenderness for varying concrete strength at different stress levels. Besides fatigue strength, nondestructive testing is carried out additionally. Methods used are strain measurement and ultrasonic testing. The change of strain, stiffness and ultrasonic pulse velocity in the fatigue process is discussed. Results disclose a deeper insight into the damage process under cyclic loading of high-performance concrete and contribute to improve nondestructive monitoring. T2 - LORCENIS - Long Lasting Reinforced Concrete for Energy Infrastructue under Severe Operating Conditions CY - Gent, Belgium DA - 10.09.2019 KW - Compressive Cyclic loading KW - Fatigue KW - High-strength concrete KW - Non destructive testing KW - Ultrasonic testing PY - 2019 AN - OPUS4-49474 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nerger, Deborah T1 - Improved tomographic investigation for impact damage characterization N2 - Reinforced concrete (RC) is used as structural material in most diverse civil engineering applications. For the variability of its physical properties it is still an engineering challenge to meet all necessary requirements for the prediction of dynamic effects under impact loading. In this paper, investigations are shown within the scope of quantifying and evaluating the damage caused by an impact. The experimental investigations are performed in the field of low- and medium-velocity impact. The chosen flat nose shape results in small penetrations on the top side and scabbing on the bottom side. The plate is scanned with an adapted planar tomographic examination after the impact, and the damage is analysed, afterwards. Cracks and spalling are made visible with a reconstruction. The numerical model validated on the tomographic results justifies the application for further predictions of the damage description. T2 - 25th International Conference on Structural Mechanics in Reactor Technology - SMIRT25 CY - Charlotte, NC, USA DA - 04.08.2019 KW - Impact KW - Damage characterization KW - Planar tomography KW - Numeric simulation KW - Reinforced concrete structure PY - 2019 AN - OPUS4-49540 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zencker, Uwe T1 - Brittle failure of spent fuel claddings during long-term dry interim storage N2 - In order to demonstrate the safety of both spent fuel and the storage system, a good understanding of the processes that might cause deterioration is required. The International Atomic Energy Agency (IAEA) continued the coordinated research on Spent Fuel Performance Assessment and Research (SPAR) into a fourth phase starting in 2015 to evaluate fuel and materials performance under wet and dry storage and to assess the impact of interim storage on associated spent fuel management activities (such as handling and transport). BAM’s understanding and experiences in the field of long-term storage of spent fuel and especially spent fuel characterization are presented to assist the preparation of the final project report. T2 - IAEA CRP SPAR-IV Third Research Coordination Meeting (RCM3) CY - Buenos Aires, Argentina DA - 07.10.2019 KW - Fuel rod KW - Cladding KW - Radial hydrides KW - Ring compression test KW - Failure analysis PY - 2019 AN - OPUS4-56006 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zencker, Uwe T1 - Embrittlement of spent fuel claddings during long-term dry interim storage - Current approach at BAM N2 - The integrity of fuel rods and cladding tubes must be demonstrated throughout the dry interim storage of spent nuclear fuel in Germany. For at least a relevant number of casks, an extension of interim storage between 40 and 100 years is foreseeable. The drying procedure for the fuel rods in conjunction with the thermomechanical storage conditions may change the microstructure of the cladding tubes and lead to their possible embrittlement. The failure probability might increase under mechanical load by handling procedures (transport after storage) on potentially embrittled cladding tubes of fuel rods especially at low temperatures after long-term storage. Results of ring compression tests on unirradiated pre-hydrided as well as irradiated samples with radial hydrides are investigated by finite element analyses to be able to describe the failure process and to identify failure criteria. T2 - EPRI Extended Storage Collaboration Program (ESCP) Winter 2019 Meeting CY - Charlotte, NC, USA DA - 04.11.2019 KW - Fuel rod KW - Cladding KW - Radial hydrides KW - Ring compression test KW - Failure analysis PY - 2019 AN - OPUS4-56005 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zencker, Uwe T1 - Spent Fuel Characterization - Current Activities in Germany N2 - The characterization of spent fuel and radioactive waste is essential in the evaluation of the ability of these materials to meet acceptance criteria. Prior to determining a method for spent fuel characterization, it is necessary to identify the type of data required to support safety and other analyses for the storage, transportation and final disposal of spent fuel. BAM’s understanding and capabilities in the field of spent fuel characterization are presented for the scope of a coordinated research project on the topic. T2 - IAEA Technical Meeting on Spent Fuel Characterization for Management of Spent Fuel in the Back End of the Fuel Cycle CY - Vienna, Austria DA - 12.11.2019 KW - Nuclear fuel cycle KW - Back end KW - Spent fuel characterization KW - Storage KW - Transportation PY - 2019 AN - OPUS4-55866 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Linnemann, Konrad T1 - Numerical simulation of spent fuel segments under transport loads N2 - Packages for the transport of spent nuclear fuel shall meet the International Atomic Energy Agency regulations to ensure safety under different Transport conditions. The physical state of spent fuel and the fuel rod cladding as well as the geometric configuration of fuel assemblies are important inputs for the evaluation of package capabilities under these conditions. Generally, the mechanical behavior of high burn-up spent fuel assemblies under Transport conditions shall be analyzed with regard to the assumptions which are used in the containment and criticality safety analysis. In view of the complexity of the interactions between the fuel rods as well as between the fuel assemblies, basket, and cask containment, the exact mechanical analysis of such phenomena is nearly impossible. The gaps in information concerning the material properties of cladding and pellet behavior, especially for the high burn-up fuel, make the analysis more complicated additionally. As a result, enveloping analytical approaches are usually used by BAM within the safety assessment of packages approved for transport of spent nuclear fuel. To justify the safety margins of such approaches additional analyses are necessary. In this paper, numerical simulations of a segment of a spent fuel assembly are presented. The segment modeled represents the part of a generalized BWR fuel assembly between two spacers. Explicit dynamic finite element calculations are performed to simulate the spent fuel behavior under regulatory defined accident conditions of transport. A beam element formulation is used for the modeling of the fuel rods representing the compound consisting of claddings and fuel pellets. The load applied is gathered from experimental drop tests with spent fuel casks performed at BAM. A hot cell bending test performed at JRC Karlsruhe is the basis for obtaining the material behavior of the fuel rods. The material properties are determined by simulating the test setup of JRC and optimizing the results to fit the experimental load deflection curve. The simulations of the fuel Assembly segment are used to get a better understanding about the loads on fuel rods under accident conditions of transport. T2 - 17th International High-Level Radioactive Waste Management Conference (IHLRWM 2019) CY - Knoxville, Tennessee, USA DA - 14.04.2019 KW - Spent Nuclear Fuel KW - Finite Element Simulation KW - Transport packages PY - 2019 AN - OPUS4-52047 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg W. T1 - Relevante Entwicklungen zu Speichern für Gase als Energieträger N2 - Es werden die Zusammenhänge des Druckvolumenprodukts und der Konsequenz bei Druckgasen insbesondere für Wasserstoff dargestellt. Entsprechend werden Stellungnahmen zu verschiedenen Normungsprojekten abgeleitet und perspektivische Entwicklungen mit dem resultierenden Bedarf in der Normung dargestellt. Außerdem wird am Beispiel ein Problem in der praktischen Beurteilung von Speicherpopulationen für Batteriefahrzeuge diskutiert. T2 - 26. BAM-DIN-IGV-DVFG-Gespräch 2019 CY - Berlin, Germany DA - 27.02.2019 KW - Wasserstoffspeicher KW - Konsequenzbegrenzung KW - Normung KW - Druck-Volumen-Produkt KW - Katastrophe KW - Akzeptanz PY - 2019 AN - OPUS4-53145 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gröke, Carsten T1 - Requirements for Package Design Testing and Quality Assurance Measures for Packages not Requiring Competent Authority Design Approval N2 - Übersicht über die gefahrgutrechtlichen Anforderungen zur Bauartprüfung und dem Qualitätsmanagement für Verpackungen für nicht zulassungspflichtige Versandstücke. T2 - KONTEC 2019 CY - Dresden, Germany DA - 27.03.2019 KW - Bauartprüfung KW - Qualitätsmanagement KW - Nicht zulassungspflichtig PY - 2019 AN - OPUS4-56352 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grunewald, Thomas T1 - Nichtelektrischer Explosionsschutz: Zündgefahren durch Funken - Grundlagen und Maßnahmen zum Explosionsschutz N2 - Bei Geräten und Maschinen zur bestimmungsgemäßen Verwendung in explosionsgefährdeten Bereichen muss in der europäischen Union eine Zündgefahrenbewertung durchgeführt werden. Dabei müssen unter anderem die Gefahren von nichtelektrischen Zündquellen betrachtet werden, zu denen auch die mechanischen Schlagvorgänge gehören. Bei Schlagvorgängen kommt es infolge des Zusammenstoßes zweier Werkstücke zu einer Umwandlung der kinetischen Energie. Dabei erhöht sich die Temperatur der Werkstoffe an der Kontaktstelle und es kommt unter Umständen zu einem Abtrennvorgang kleiner Partikel erhöhter Temperatur. Sowohl die heißen Kontaktstellen als auch die abgetrennten Partikel können eine wirksame Zündquelle für ein explosionsfähiges Gasgemisch darstellen. Zur Festlegung von Grenzwerten wurden in der Norm EN 13463-1:2009 die Gasgemische anhand ihrer Explosionsgruppe klassifiziert und zu jeder Gruppe die maximale Energie des Schlagvorgangs festgelegt, unter derer die Entstehung einer wirksamen Zündquelle als unwahrscheinlich angenommen werden kann. T2 - Ausbildung zum Explosionsschutzbeauftragten (Veranstaltungsnr.: E-H050-04-473-9) CY - RWTH Aachen und Universität Duisburg-Essen, Germany DA - 09.04.2019 KW - Funken KW - Mechanisch erzeugte Funken KW - Nichtelektrische Funken KW - Nichtelektrischer Explosionsschutz KW - Schlagfunken PY - 2019 AN - OPUS4-47951 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Potentialmessung im Stahlbetonbau N2 - Durch das alkalische Porenwassermilieu ist Stahl im Beton vor Korrosion geschützt. Unter ungünstigen Umgebungsbedingungen (Karbonatisierung, Chlorideintrag) kann die passive Deckschicht auf der Stahloberfläche zerstört werden. Im weiteren Verlauf können sich korrosionsbedingte Folgeschäden, wie Risse und Abplatzungen am Bauwerk ergeben. Um notwendige Sanierungsmaßnahmen sind frühzeitige und weitgehend zerstörungsfrei ermittelte Informationen über das aktuelle Korrosionsverhalten der Stahlbewehrung von großer Bedeutung. Die Potentialfeldmessung ist ein etabliertes und weit verbreitetes Verfahren zur Beurteilung des Korrosionszustandes der Bewehrung in Stahlbetonbauwerken. Mit Hilfe dieses Verfahrens können Bereiche aktiv korrodierender Bewehrung zerstörungsfrei lokalisiert werden. In der Regel kommt diese Messmethode bei der Detektion chloridinduzierter Korrosion zum Einsatz. T2 - KKS-Lehrgang CY - TAE Esslingen, Germany DA - 06.05.2019 KW - Korrosion KW - Potentialfeldmessung KW - Corrosion KW - Concrete PY - 2019 AN - OPUS4-47937 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Martin T1 - Brand- und Explosionsgefahren beim Umgang mit Metallstäuben N2 - Grundlagen des Brand- und Explosionsschutzes mit Schwerpunkt Metallstäube: - Gefahren - Prinzipien des Explosionschutzes - Ableiten von Schutzmaßnahmen - Bestimmung der Stoffeigenschaften - Umgang mit entsprechenden Datenbanken T2 - DGM Fortbildungsseminar "Metallpulver Erzeugen - Charakterisieren - Anwenden" CY - Universität Bremen, Germany DA - 14.03.2019 KW - Brandschutz KW - Explosionsschutz KW - Sicherheitstechnische Kenngrößen PY - 2019 AN - OPUS4-47948 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schalau, Bernd T1 - Die neue VDI Richtlinie 3783 Blatt 1 N2 - Die VDI 3783 Blatt 1 befindet sich in der Überarbeitung. Der Modellwechsel auf ein Langranges Partikelmodell hat weitreichende Auswirkungen. Es wird der aktuelle Bearbeitungsstand vorgestellt. T2 - ProcessNet Arbeitsausschuss "Stoff- und Energiefreisetzungen" CY - Frankfurt/Main, Germany DA - 29.03.2019 KW - Störfall-Verordnung KW - Auswirkungsbetrachtung PY - 2019 AN - OPUS4-47954 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grätz, Rainer T1 - IEC TC 31/SC 31M and CEN TC 305 N2 - Overview about the status of european and international standardisation in the field of explosion protection of nonelectrical equipment and protective Systems. T2 - Co-ordination of Notified Bodies - Directive 2014/34/EU of the European Parliament and of the Council (ATEX), 22nd EXNB Meeting CY - Brussels, Belgium DA - 05.02.2019 KW - Norm KW - ATEX PY - 2019 AN - OPUS4-47950 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stajanca, Pavol T1 - Fiberoptic sensors for composite/plastic components monitoring N2 - An overview of Division 8.6 activities on using optical fiber sensors for composite monitoring is given. T2 - Workshop an der TU Chemnitz CY - Chemnitz, Germany DA - 06.05.2019 KW - Fiberoptic sensors KW - Composites KW - Sensor intergration KW - Polymer optical fibers PY - 2019 AN - OPUS4-47969 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Aris, Stephan T1 - Konformitätsbewertung von ortsbeweglichen Druckgeräten nach Richtlinie 2010/35/EU (TPED) N2 - Im Vortrag werden die Anforderungen und das Konformitätsbewertungsverfahren für ortsbewegliche Druckgeräte nach Richtlinie 2010/35/EU (TPED) vorgestellt. Dabei werden auch aktuell bekannte Probleme mit ortsbeweglichen Druckgeräten als Input für die Marktüberwachung angesprochen. T2 - Schulung ODV/ADR CY - Potsdam, Germany DA - 07.08.2019 KW - Ortsbewegliche Druckgeräte KW - TPED KW - ODV KW - ADR KW - Konformitätsbewertung KW - Marktüberwachung PY - 2019 AN - OPUS4-48697 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pohl, Christoph T1 - Pore water state in heated concrete N2 - Spalling of concrete structures is a serious issue for their safety. A better understanding of the pore water distribution and state during a fire is a prerequisite for numerical approaches to such problems. Temperature-driven water transport in concrete consists of multiple phenomena, such as convection, diffusion, adsorption and dehydration. Distinguishing the different influences experimentally is difficult because typically they cannot be disentangled. A common experimental setup approximates a one-dimensional flow, and places temperature and pressure gauges along the propagation direction. For direct information about the water content inside a sample, methods such as NMR or neuron radiography are necessary. A multiphase model for the flow in porous media is presented, with dehydration and changes in the pore size distribution taken into consideration. NMR measurements for temperature-driven flow have been performed. The numerical and experimental results are compared for water transport at temperatures below the critical point. Since both the finite-element model and the experiment allow the distinction between adsorbed, capillary and bulk water, a more fine-grained view of the pore water state is obtained. T2 - CM4P - Computational methods in multi-scale, multi-uncertainty and multi-physics problems CY - Porto, Portugal DA - 15.07.2019 KW - Spalling KW - Porous media KW - Multiphase flow KW - Finite element method PY - 2019 AN - OPUS4-48707 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pelzl, T. T1 - Umgang mit Propan und Acetylenflaschen im Brandeinsatz N2 - Die BAM hat umfangreiche Versuchsreihen zur Auswirkungsbetrachtung des Versagens von Acetylen- und Propanbehältern auf dem TTS durchgeführt. In Zusammenarbeit mit verschiedenen Partnern entstanden zwei Merkblätter mit praktischen Hinweisen für Einsatzkräfte, die die aktuellen Forschungsarbeiten der BAM berücksichtigen. Im Rahmen dieses Vortrages wurden den Einsatzkräften die Inhalte und Hintergründe der Merkblätter erläutert T2 - 22. Fachtagung "Gefährliche Stoffe" des Bezirksfeuerwehrverbandes Oberbayern e. V. CY - Kehlheim, Germany DA - 05.07.2019 KW - Behälterversagen KW - Gefahrstoffe KW - Feuerwehr KW - Acetylen KW - Propan PY - 2019 AN - OPUS4-48700 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gnutzmann, Tanja T1 - Analysis of fire gases in early stages N2 - A promising approach for the further improvement of fire detection techniques is the inclusion of fire gases in the characteristics used to detect a fire. A screening of sample materials representative for common first burning items and their gas release under different ignition conditions was performed to gain an overview of possible target gas candidates. Different fire scenarios were investigated to evaluate fire gases produced in early stages of fire development, their time of appearance and concentration development using the vitiated mass loss calorimeter and a heating plate setup in the single burning item test chamber. T2 - Interflam 2019 CY - London, UK DA - 01.07.2019 KW - Detection PY - 2019 AN - OPUS4-48664 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dreyhsig, Gesa T1 - Deflagrationen von Methan-Luft-Gemischen N2 - Überblick der bisherigen Ergebnisse einer Bachelorarbeit, die sich mit dem Einfluss von Flammenausbreitungen in geschlossenen Systemen auf die Druckanstiegsgeschwindigkeiten der explosionsartigen Verbrennung von Methan-Luft-Gemischen beschäftigt. T2 - Anorganisch-chemisches Symposium 2019 CY - Edersee, Germany DA - 13.07.2019 KW - Druckanstiegsgeschwindigkeit KW - Deflagration KW - Methan-Luft-Gemisch KW - Flammenausbreitung PY - 2019 AN - OPUS4-48674 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor T1 - Einkomponentige alkaliaktivierte Bindemittel und Mörtel mit hohem Schwefelsäure-Widerstand N2 - Einkomponentige alkaliaktivierte Bindemittel (AAB), d. h. AAB, bei denen der Aktivator als Feststoff im Bindemittel vorliegt, weisen Vorteile hinsichtlich der praktischen Anwendung im Bauwesen gegenüber konventionellen AAB auf. Einkomponentige AAB lassen sich als Gemische aus reaktiver Silica und Natriumaluminat herstellen, wobei die Reaktionsprodukte von der eingesetzten Silica und den Verhältnissen Na2O/Al2O3/SiO2/H2O abhängen: Während Mikrosilica und ähnliche Reststoffe zu zeolithreichen Produkten führen, erhält man aus Reisschalenasche vollständig amorphe Gele (sog. «Geopolymere»). Mörtel auf Basis solcher Bindemittel entsprechen den Anforderungen von DIN 19573:2016-03 hinsichtlich des Widerstands gegen Schwefelsäureangriff (Prüfung bei pH = 1 für 70 d) und sind damit potentiell als Reparatursysteme für Abwasserinfrastruktur geeignet. Untersuchungen mittels 29Si-MAS-NMR und 1H-29Si-Kreuzpolarisations(CP)-MAS-NMR sowie REM-Aufnahmen von erhärteten und dem Schwefelsäureangriff ausgesetzten AAB zeigen, dass der hohe Säurewiderstand v. a. auf die Fällung von Silicagel an der Grenzfläche Mörtel/Säure zurückzuführen ist, wodurch der Korrosionsfortschritt in darunterliegenden Schichten verlangsamt wird. T2 - Tagung Bauchemie der GDCh-Fachgruppe Bauchemie CY - Aachen, Germany DA - 30.09.2019 KW - Alkaliaktivierte Bindemittel KW - Biogene Schwefelsäurekorrosion KW - Abwasserinfrastruktur KW - Reparatursysteme PY - 2019 AN - OPUS4-49269 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kutz, Philipp T1 - Entwicklung einer einwandigen Transporteinheit aus GFK für kryogene Flüssigkeiten N2 - Präsentation im Rahmen eines BAM-internen Kolloquiums über den aktuellen Stand der Forschung im ZIM-Vorhaben "Tieftemperatzr-Transporteinheit aus Faserverbundkunststoffen" T2 - BAM-Kolloquium CY - Berlin, Germany DA - 10.10.2019 KW - LNG KW - GFRP KW - Lightweight design PY - 2019 AN - OPUS4-49276 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Patrick T1 - Structural Health Monitoring (SHM) unter Temperatureinflüssen N2 - Beim Structural Health Monitoring (SMH) besteht eine der Hauptsächlichen Störgrößen im Einfluss der Umgebungsbedingungen, insbesondere der Temperatur. Es wird ein Einblick in die Problemstellung gegeben sowie Lösungsansätze diskutiert und aktuelle Forschung an der BAM vorgestellt. T2 - Internes Arbeitskolloquium TU Berlin CY - Berlin, Germany DA - 11.10.2019 KW - Structural Health Monitoring KW - Structural Health Monitoring KW - Temperatureinflüsse KW - Temperature effects KW - SHM KW - SHM PY - 2019 AN - OPUS4-49265 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wu, Cheng-Chieh T1 - A Four-Point Bending Test Apparatus for Measurement- and Model-based Structural Analysis N2 - By means of a small-scale truss bridge, the ability of the Measurement- and Model-based Structural Analysis to detect and localize damage was examined. Although there was no noteworthy difficulty in detecting damage, it turned out that damage localization responds sensitively to systematic influences, i.e. non-modelled properties of the mechanical model. Therefore, another experiment is being conducted to re-examine the Measurement- and Model-based Structural Analysis. For this purpose, the bending test is carried out as it has been already theoretically respectively numerically discussed. In this attempt, the systematic influences such as residual stress are kept as low as possible. T2 - 36th Danubia Adria Symposium on Advances in Experimental Mechanics CY - Pilsen, Czech Republic DA - 24.09.2019 KW - Damage detection KW - Adjustment calculation KW - Finite element method PY - 2019 AN - OPUS4-49291 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Werner, Jan T1 - Fire tests on BAM TTS test facilities N2 - Overview Test facilities TTS Division 3.2 for ´visit of IRSN T2 - Technical Exchange IRSN – BAM CY - BAM TTS, Germany DA - 12.09.2019 KW - FIRE TESTS BAM TTS TEST FACILITIES PY - 2019 AN - OPUS4-49194 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Radnik, Jörg T1 - Redox properties of Cu ions in molecular sieves N2 - Molecular sieves as materials with defined pores offer new opportunities in the preparation of nanostructured materials for different applications in chemistry, medicine and biology. Typical examples for such materials are zeolites, porous glass, different silicas and active carbon. Introducing transition metal ions in such materials can widen the possibilities of these materials in terms of chemical activity. Especially, the opportunity to tailor the redox properties of the transition metal ions by varying the location of the ion in the sieves is a promising way to obtain catalysts with the desired properties. For this purpose, Cu2+ ions were introduced into a SAPO-5 (silicoaluminaphosphate) by a hydrothermal method and by impregnation. As expected, the different preparation methods led to different locations of the Cu2+ ions: by the hydrothermal method the ions were incorporated in the SAPO-5 framework, by impregnation mononuclear Cu species randomly distributed in the pores of the support or CuO particles were formed depending on the Cu amount. These locations could be determined by Extended X-ray Absorption Fine Structure and Anomalous Small-Angle X-ray Scattering investigations. For investigating the redox properties of the Cu2+ ions the differently prepared sample were treated in Ar and H2 atmosphere until 550°C. X-ray Photoelectron Spectroscopy was performed to study the valence states of Cu after each of such treatment. For a definite determination of the valence states, both Cu 2p and Cu LMM spectra must be recorded. Cu2+ exhibits a clear chemical shift and a typical satellite structure in Cu2p spectra, but between mono- and zerovalent Cu a differentiation is not possible. On the other hand, these two species show a clear shift in the Auger spectra. Whereas in H2 atmosphere in any case metallic Cu was formed, the treatment in Ar showed significant differences between the samples. Cu2+ incorporated in the framework could not be reduced by this treatment. In contrast, the mononuclear Cu2+ species were reduced to stable Cu+. Likewise, the CuO nanoparticles were reduced to the monovalent Cu, but this species can be much more easily reoxidized in air. The consequences for the catalytic properties will be discussed. T2 - ECASIA 2017 CY - Montpellier, France DA - 24.09.2017 KW - Catalysis KW - X-ray photoelectron spectroscopy KW - Nanostructured materials PY - 2017 AN - OPUS4-42323 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erenberg, Marina T1 - Impact limiter behaviour under IAEA fire test conditions N2 - Accident safe packages for the transport of spent nuclear fuel and high-level waste shall fulfil international IAEA safety requirements. Compliance is shown by consecutive mechanical and thermal testing. Additional numerical analysis are usually part of the safety evaluation. For damage protection some package designs are equipped with wood filled impact limiters encapsulated by steel sheets. The safety of these packages is established in compliance with IAEA regulations. Cumulative mechanical and fire tests are conducted to achieve safety standards and to prevent loss of containment. Mechanical reliability is proven by drop tests. Drop testing might cause significant damage of the impact limiter steel sheets and might enable sufficient oxygen supply to the impact limiter during the fire test to ignite the wood filling. The boundary conditions of the fire test are precisely described in the IAEA regulatory. During the test the impact limiter will be subjected to a 30 minutes enduring fire phase. Subsequent to the fire phase any burning of the specimen has to extinguish naturally and no artificial cooling is allowed. At BAM a large-scale fire test with a real size impact limiter and a wood volume of about 3m³ was conducted to investigate the burning behaviour of wood filled impact limiters in steel sheet encapsulation. Until today burning of such impact limiters is not sufficiently considered in transport package design and more investigation is necessary to explore the consequences of the impacting fire. The objective of the large scale test was to find out whether a self-sustaining smouldering or even a flaming fire inside the impact limiter was initiated and what impact on the cask is resulting. The amount of energy transferred from the impact limiter into the cask is of particular importance for the safety of heavy weight packages. With the intention of heat flux quantification, a new approach was made and a test bench was designed. T2 - Abteilungskolloquium Abteilung 3 CY - BAM, Berlin, Germany DA - 10.07.2019 KW - Stoßdämpfer KW - Brandversuche KW - Transportbehälter PY - 2019 AN - OPUS4-49398 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Korrosion von Stahl in Beton - Korrosionsmonitoring N2 - Korrosion von Stahl in Beton ist oft maßgebend für die Nutzungsdauer von Infrastrukturbauwereken aus Stahlbeton. Um rechtzeitig Instandsetzungsmaßnahmen einleiten zu können bietet sich ein Korrosionsmonitoringkonzept an solchen Bauwerken an. T2 - Verbundtreffen AISTEC CY - Berlin, Germany DA - 24.10.2019 KW - Korrosion KW - Potentialfeldmessung KW - Monitoring PY - 2019 AN - OPUS4-49414 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank T1 - Sloshing in vertical circular Tanks and Earthquakes Perturbations N2 - Tanks with capacity larger than 700 m3, could be exposed to a resonance excitation when subjected to earthquake motions, regardless of the fill level. Further studies to assess the dynamic forces linked to such resonance and close-to-resonance situations, in a context of a standard overloading situation due to sloshing forces. T2 - WCECS 2019 CY - San Francisco, CA, USA DA - 22.10.2019 KW - Sloshing KW - Tanks KW - Earthquake KW - Perturbation PY - 2019 AN - OPUS4-49408 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Innovative Korrosionsforschung N2 - Darstellung innovativer, kombinierter Messverfahren zur Bestimmung spezifischer elektrochemischer Kennwerte. T2 - AK Korrosionsschutz im konstruktiven Ingenieurbau CY - Frankfurt am Main, Germany DA - 18.10.2019 KW - Korrosion KW - Corrosion PY - 2019 AN - OPUS4-49329 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Bahnerschütterungen bei verschiedenen Böden und Zuggeschwindigkeiten – Messungen in Deutschland, Österreich und der Schweiz N2 - Die Bundesanstalt für Materialforschung und -prüfung hat in den letzten 30 Jahren an vielen Orten Bahnerschütterungen gemessen. Dabei wurden immer auch Versuche zur Bestimmung der Bodeneigen-schaften durchgeführt, meist mit Hammeranregung, gelegentlich auch mit Schwingeranregung. Es werden verschiedene Auswertemethoden wie Seismogramm-Montage, Spektrale Analyse (SASW), Multistation Analysis of Surface Waves (MASW), f,v-Analyse (Dispersion aus zweifacher Fourier-Analyse), Spatial AutoCorrelation (SPAC, hier auch für deterministische Quellen) vorgestellt. Durch Approximation der frequenzabhängigen Wellengeschwindigkeiten (Dispersion) oder der gemessenen Übertragungsfunktionen erhält man ein passendes Bodenmodell. Zu diesem Bodenmodell kann man dann die Übertragungsfunktionen für Hammer- und Zuganregung berechnen. Mit allgemeinen oder spezifischen Achslastspektren werden dann die Bahnerschütterungen prognostiziert und mit den Messergebnissen verglichen. Bei etlichen Messorten, insbesondere in der Schweiz, wurden deutliche Merkmale einer Bodenschichtung beobachtet. Es ergibt sich eine deutliche Reduktion der tiefen Frequenzanteile durch den steifen unterliegenden Halbraum. Die weiche Deckschicht bestimmt das hochfrequente Verhalten. Hier bewirkt die Materialdämpfung des Bodens oft einen starken Amplitudenabfall, sowohl mit der Entfernung als auch mit der Frequenz. Für den verbleibenden mittelfrequenten Anteil wurde an mehreren Messorten die Amplituden-Fahrgeschwindigkeits-Gesetzmäßigkeiten untersucht. Es gibt konstante bis stark ansteigende Amplituden, und es zeigt sich auch hier, dass der geschichtete Boden von entscheidender Bedeutung ist. T2 - 16. D-A-CH Tagung Erdbebeningenieurwesen & Baudynamik (D-A-CH 2019) CY - Innsbruck, Austria DA - 26.09.2019 KW - Zuggeschwindigkeit KW - Wellengeschwindigkeit KW - Dispersionsmessung KW - Bodenübertragungsfunktion KW - Bahnerschütterungen PY - 2019 AN - OPUS4-49445 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Günther, Martin T1 - Bubbles and Collapses: Fire Phenomena of Polyurethane Foams N2 - This work investigates the fire phenomena of rigid polyurethane foams (RPUFs) in detail. To elucidate structure-property relationships, systematically varied sets of materials were prepared covering polyurethane, polyisocyanurate-polyurethane and flame retarded polyurethane foams. Advanced cone calorimeter investigations provide insight into the fire behavior under forced flaming conditions. Thermocouples inside specimens give information about the temperature gradient during combustion. Furthermore, fire phenomena were characterized using cross sections of quenched samples and the scanning electron microscope. By using a Multi methodological approach and systematically varied sets of foam materials, new insights into the burning of RPUFs were won. For the flame retarded foams, the dominant flame retardant mode of action changed with density. PIR foams exhibited a cellular structure in the residue leading to the superior fire performance compared to polyurethane foams. The understanding of fire phenomena contributes to future development of tailored flame retardant strategies for RPUFs. T2 - AOFSM’3, 3rd Asia-Oceania Symposium for Fire Safety Materials Science and Engineering CY - Shanghai, China DA - 24.10.2019 KW - PU-Foam KW - Fire behaviour PY - 2019 AN - OPUS4-49457 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Burkert, Andreas T1 - Korrosionsmonitoring bei der Instandsetzung von chloridbelasteten Stahlbetonwerken N2 - In der aktuellen RL-SIB wie auch im Gelbdruck der Instandhaltungsrichtlinie ist bei Anwendung des Instandsetzungsprinzips W-Cl bzw. Verfahren 8.3 der Erfolg der Maßnahme durch Einbau und Messung von Korrosionsstrom-Mess-Einrichtungen nachzuweisen. Auch wird bei der Instandsetzung von chloridbelasteten Rissen bei Stahlbetonbauteilen durch Verpressen der Risse bzw. Aufbringen einer Rissbandage ein Korrosionsmonitoring empfohlen. Anerkannte Regelwerke oder Normen über Art und Aufbau des Monitoring-Systems sowie Kriterien zur Bewertung der Messergebnisse im Hinblick auf den Erfolg der Instandsetzungsmaßnahme gibt es derzeit nicht. Auch sind keine Untersuchungen zur Qualität der Messergebnisse veröffentlicht. Ziel des Vorhabens ist die Ausarbeitung eines Regelwerks-Entwurfes für die Art und den Aufbau von Korrosionsmonitoring-Systemen sowie für Kriterien zur zuverlässigen Bewertung der Messergebnisse, mit denen der Erfolg bei verschiedenen Instandsetzungskonzepten überprüft werden kann. T2 - 13. Sitzung des NA 062 01 77 AA „Korrosionsprüfverfahren“ CY - Neuss, Germany DA - 24.10.2019 KW - Korrosion KW - Monitoring KW - Sensoren KW - Chloridbelastete Stahlbetonbauwerke PY - 2019 AN - OPUS4-49462 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Four typical errors in train induced ground vibration and ground vibration mitigation N2 - Mitigation measures of railway induced vibration have been demonstrated at the emission, transmission and immission part. It must be carefully observed that the correct masses and stiffnesses are used. Typical mistakes have been shown, - 1D models for vehicle-track interaction, - impedance instead of stiffness for the infill material of a trench, - rigid buildings or neglecting the soil-building interaction. The dominant mid-frequency part of the ground vibration is due to the irregular soil. T2 - ISO/TC 108/SC 2/WG 8 Working group Ground-borne noise and vibration from rail systems CY - Milano, Italy DA - 14.10.2019 KW - Ground vibration KW - Train excitation KW - Mitigation PY - 2019 AN - OPUS4-49446 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Predicted and measured amplitude-speed relations of railway ground vibrations at four German sites with different test trains N2 - The present contribution evaluates four measuring series made by the Federal Institute of Material Research and Testing for the relations between train speed and ground vibration amplitudes. This experimental evaluation is supported by the simulation of the train passages at the different sites by using appropriate excitation mechanisms and forces as well as layered soil models which have been derived from impact measurements at each site. T2 - 13th International Workshop on Railway Noise and Vibration CY - Leuven, Belgium DA - 16.09.2019 KW - Excitation forces KW - Train speed KW - Ground vibration KW - Layered soils PY - 2019 AN - OPUS4-49444 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Katja A1 - Tscheuschner, Frank T1 - Datenbank GEFAHRGUT - Ein gemeinsames Projekt vom BMVI und der BAM N2 - Es werden die Anwendungen des Gefahrgutdatenpools der BAM aufgezeigt, der ein zentrales Informationssystem für den Transport gefährlicher Güter darstellt. T2 - 21. Stuttgarter Gefahrguttag CY - Stuttgart, Germany DA - 24.10.2019 KW - Datenbank GEFAHRGUT KW - Gefahrgut-Schnellinfo KW - Gefahrgutdatenpool KW - Gefahrguttransport KW - Informationssystem KW - Kurzinfo KW - Modul für Beförderungspapier KW - Modul für radioaktive Stoffe KW - BAM Liste KW - BAM List KW - Dangerous Goods Database KW - Dangerous Goods Quickinfo KW - Radioactive Materials Module KW - Transport Documents Module PY - 2019 AN - OPUS4-49467 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Malow, Marcus T1 - CEQAT-DGHS Development of procedures for the verification of test apparatuses (Example UN Test N.5) N2 - This presentation focuses on General aspects of development of verification methods. The development of verification methods is demonstrated using the test method UN Test N.5 as an example. T2 - EOS IGUS Meeting CY - Brussels, Belgium DA - 21.05.2019 KW - Dangerous Goods KW - UN-Test N.5 KW - Verification method KW - Measurement uncertainty PY - 2019 AN - OPUS4-49003 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlick-Hasper, Eva T1 - Vergleich von Worst-Case-Grenzleckageraten mit der Empfindlichkeit des Bubble Test N2 - Der derzeit in den Gefahrgutvorschriften genannte Bubble Test ist keine geeignete Prüfmethode, um für alle Verpackungsvolumina ein Dichtheitsniveau sicherzustellen, welches auf Sicherheitsbetrachtungen unter Beförderungsbedingungen basiert. Für kleinere Verpackungsbauarten müssten theoretisch empfindlichere Prüfmethoden angewandt werden. Auf der anderen Seite sollten Bauartprüfungen für Gefahrgutverpackungen nicht zu kompliziert sein. Daher sollte die Auswahl einer Methode erfolgen, die sowohl eine ausreichende Empfindlichkeit aufweist als auch über eine einfache Art der Durchführung verfügt. T2 - 32. Sitzung des BAM AK Prüfstellen CY - Berlin, Germany DA - 17.09.2019 KW - Gefahrgutverpackungen KW - Dichtheit KW - Bubble Test PY - 2019 AN - OPUS4-48991 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erdt, René T1 - Selbstentzündungsverhalten von Feststoffen: Validierung der Extrapolation von Labortests mit Hilfe halbtechnischer Versuche bis 1 m³ N2 - Vorgestellt wird ein 2018 gestartetes Projekt zur Überprüfung der Extrapolation von im Labormaßstab ermittelten Selbstentzündungstemperaturen auf technisch relevante Volumina. Für die Ermittlung reaktionskinetischer Daten von Feststoffschüttungen stehen eine Reihe von Untersuchungsmethoden zur Verfügung. Dies sind thermische Analysen wie z.B. die differential scanning calorimetry DSC sowie Mikrokalorimetrie zur hochgenauen Messung von Wärmeströmen, bei denen sehr geringe Probenmengen zum Einsatz kommen. In der Regel wird das Selbstentzündungsverhalten jedoch mit Hilfe von isoperibolen oder adiabaten Warmlagerungsversuchen beurteilt, hier liegen die Probenvolumina üblicherweise im Bereich von ca. 100 cm³ bis zu einigen Litern. Die Extrapolation über mehrere Größenordnungen auf technische Volumina birgt Unsicherheiten, da mit Zunahme des Lagervolumens veränderte Start- und Randbedingungen vorliegen können. Zudem besteht die Möglichkeit, dass bei in technischen Lagern vorherrschenden niedrigen Temperaturen Reaktionen ablaufen, die in Standard- Laborversuchen nicht erfasst werden aber einen wesentlichen Einfluss auf das Selbstentzündungsverhalten aufweisen können. Hauptziel des Projektes ist es daher, die im Labormaßstab vorhandenen Prüfeinrichtungen durch einen Versuchsstand zur Untersuchung von Probengrößen von bis zu 1000 dm³ zu erweitern, die Eignung (oder Nichteignung) der etablierten Methoden nachzuweisen und im Labormaßstab nicht erfassbare Einflussgrößen zu ermitteln. Zudem sollen anhand der kleinskaligen Tests Entscheidungskriterien abgeleitet werden, ob eine Extrapolation nach den derzeit üblichen Methoden zulässig ist. T2 - 15. BAM-PTB-Kolloquium CY - Braunschweig, Germany DA - 21.05.2019 KW - Spontanious ignition KW - Self-ignition KW - Minimum ignition temperature KW - Dust layers PY - 2019 AN - OPUS4-48995 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Küttenbaum, Stefan T1 - Refining stochastic models for the reassessment of bridges using NDT-methods N2 - Increasing requirements on the infrastructure caused by more and heavier traffic coincide with both the aging and the progressive degradation of bridge constructions. These exemplary issues lead to a non-negligible need for reassessments of existing bridges. Compared to the new building design, safety reserves can be used in the evaluation of such existing structures, since uncertainties that may arise during the design, construction and previous Service time are better known or no longer present. Uncertainties can be evaiuated more precisely by measurements. In the meantime, the application of advanced NDT-methods on concrete structures have become so capable, that crucial structure Parameters like certain material properties or geometrical dimensions can be quantified without significant destructive interventions. The measured data can be explicitly incorporated into the probabilistic computation models used for the bridge reassessment in form of random variables. Therewith, a previously insufficient model can be refined to achieve a higher level of approximation. This contribution emphasises two fundamental steps of the measured data based probabilistic reassessment: The sensitivity analyses to identify the cruciai Parameters and the needed accuracy of the related information as well as the comparison with expected uncertainties of non-destructively measured Parameters. T2 - 17th International Probabilistic Workshop CY - Edinburgh, UK DA - 11.09.2019 KW - Measurement KW - Reassessment KW - Structural safety KW - Concrete bridges KW - NDT PY - 2019 AN - OPUS4-48999 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Askar, Enis T1 - Safety related properties of low-GWP refrigerants N2 - Most fluorinated hydrocarbons that shall replace refrigerants with high GWP. like R134a. are flammable. For evaluating inertization measures for explosion protection. flammability of low-GWP refrigerants R1234yf, R32 and R1132a blended with carbon dioxide. Nitrogen and argon were studied experimentally in a closed autoclave at atmospheric conditions. Furthermore, a calculation method was adapted to reduce the experimental costs for flammability studies on these gas mixtures. For igniting R1234yf in the closed autoclave a newly developed ignition system was used that allows generating electric arcs with high ignition energy. Gas mixtures containing the mildly flammable R1234yf and R32 could be inerted by adding much less inert gas than mixtures containing R1132a, which is more similar to unfluorinated hydrocarbons regarding the explosion regions. By using the adapted model of constant adiabatic flame temperature profiles estimating the explosion limits of fluorinated hydrocarbons was possible with similar accuracy as for unf luorinated hydrocarbons. T2 - 25th IIR International Congress of refrigeration CY - Montreal, Canada DA - 24.08.2019 KW - Explosionsgrenzen KW - Inertisierung KW - Entzündbarkeit KW - Kältemittel KW - R1234f, R32, R1132a PY - 2019 AN - OPUS4-48994 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino T1 - Inhibition of hydrogen evolution on galvanized reinforcement in fresh concrete by addition of potassium permangante N2 - Due to the EUdirective53/2003/EEC,which has been in force since 17th January, 2005, restricts the soluble chromate content in cements to amaximum value of 2ppm. This ammount is to low to inhibit the hydrogen evolutuion by the cathodic partial reaction in fresh concrete. T2 - Eurocorr 2019 CY - Sevilla, Spain DA - 09.09.2019 KW - Corrosion KW - Galvanized reinforcement KW - Hydrogen PY - 2019 AN - OPUS4-48934 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grunewald, Thomas T1 - Gebrauch von Werkzeugen im explosionsgefährdeten Bereich – Grundlagen zur Zündquelle mechanisch erzeugte Funken – Möglichkeiten und Grenzen bei der Verwendung von NE-Metallen und Edelstahl im Ex-Bereich N2 - Der Anteil der mechanischen Zündungen an allen Unfällen bei Staub/Luft-Gemischen wird von Bartknecht mit rund 30 % beziffert. Am Beispiel von Ex-Ventilatoren wurden viele Unfälle mit zum Teil erheblichen Zerstörungen an den strömungstechnischen Anlagen in einer Publikation von Witt aufgezeichnet, deren nachgewiesene oder vermutete Ursache mechanische Zündquellen mit etwa ähnlich hohem Anteil wie bei den Stäuben waren. Edelstahl ist für Geräte für die Verwendung zum bestimmungsgemäßen Gebrauch im explosionsgefährdeten Bereich insbesondere in der Chemie ein wichtiger Konstruktionswerkstoff. Hersteller von Geräten für den bestimmungsgemäßen Gebrauch in explosionsfähigen Bereichen müssen, wenn sie unter die Richtlinie 94/9/EG fallen, für das Inverkehrbringen in EU-Mitgliedsstaaten eine Konformitätsbewertung durchführen. Dazu gehört eine Zündgefahrenbewertung, bei der auch nichtelektrische Zündquellen betrachtet werden müssen, zu denen die mechanischen Schlagvorgänge gehören. Bei dieser Zündquellenart kommt es infolge des Schlages eines Bauteils auf ein anderes zu einer Energieumwandlung. Dadurch kommt es zu einer Temperaturerhöhung an der Kontaktstelle sowie unter Umständen zu einem Abtrennvorgang kleiner Partikel. Sowohl die heißen Reibflächen als auch die abgetrennten Partikel stellen potentielle Zündquellen explosionsfähiger Atmosphären dar. Für Werkzeuge im Ex-Bereich wird gelegentlich sogenanntes „funkenarmes Werkzeug aus schwer oxidierbaren NE-Metallen verwendet. Bisherige Forschungsarbeiten haben gezeigt, dass von Schlagvorgängen zwischen Bauteilen aus unlegiertem Baustahl eine erhebliche Zündgefahr von explosionsfähigen Gasgemischen ausgehen kann (Grunewald et al., 2010). Dabei ging diese Gefahr insbesondere von oxidierten Partikeln aus, die während des Schlagvorgangs abgetrennt wurden. In industriellen Anwendungen wird jedoch häufig Edelstahl statt unlegiertem Baustahl verwendet. Die geringere Oxidationsfähigkeit des Edelstahls könnte zu einer geringeren Zündfähigkeit von Schlagvorgängen mit Edelstahl im Vergleich zu Schlagvorgängen mit unlegiertem Baustahl führen Die Ergebnisse des Forschungsprojektes „NAMES 2104“ zeigen, dass Schlagvorgänge mit Edelstählen eine erhebliche Zündgefahr von explosionsfähigen Brenngasgemischen darstellen können. Dabei bestehen jedoch mitunter deutliche Unterschiede zwischen den verschiedenen Brenngasgemischen. Besonders hohe Zündwahrscheinlichkeiten konnten bei Brenngasgemischen mit Brenngasen der IEC-Explosionsgruppe IIC beobachtet werden, die Acetylen bzw. Wasserstoff als Brenngas enthielten. Schläge im Wasserstoff/Luft-Gemisch waren dabei jedoch bedeutend zündwirksamer. In diesem Gasgemisch konnte bei niedrigen maximalen Schlagenergien bis 60 J sogar eine mitunter höhere relative Zündhäufigkeit beobachtet werden als bei Versuchen mit unlegiertem Baustahl. T2 - 13. Essener Explosionsschutztage (Veranst.-Nr. H050-09-581-9), Haus der Technik (HdT) - Außeninstitut der RWTH Aachen und der Universität Duisburg-Essen CY - Essen, Germany DA - 18.09.2019 KW - Nichtelektrischer Explosionsschutz KW - Schlagfunken KW - Schleiffunken KW - Reibfunken KW - Mechanisch erzeugte Funken PY - 2019 AN - OPUS4-49025 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schartel, Bernhard T1 - Weathering resistance of halogen-free flame retardancy N2 - Whereas the degradation of flame retardant polymers has been discussed since decades, only more recently, the lifetime of the flame retardancy itself becomes an important factor, e.g. for cables used as building products. In this work, several kinds of accelerated artificial ageing tests are performed simulating different environmental exposures and thus highlighting different degradation mechanisms: artificial accelerated weathering, climatic chamber, water immersion, salt spray chamber, and autoclave test. The durability is expected to be different for different flame-retardant materials. Thus, various sets of halogen-free fire-retarded polymers were investigated: ethylene vinyl acetate (EVA) with aluminum hydroxide (ATH), boehmite and synergists, ester-based and ether-based thermoplastic polyurethane (TPU) with melamine cyanurate (MC), aluminum diethylphosphinate (AlPi), and boehmite, and glass fiber reinforced polyamide 66 (PA66) with AlPi-based mixtures. Intensive degradation of the surface was observed, e.g. yielding discoloration and yellowing, EVA showed cracking when weathered. Changes in chemical structure was investigated by ATR-FTIR. The flammability was investigated with the cone calorimeter, UL-94 classification, and oxygen index (LOI). The flame retardancy of most of the materials studied degraded only slightly for the investigated exposure times. EVA/ATH achieved an improved LOI due to flame retardants agglomeration at the surface. Sets of materials, based on EVA and TPU, were also investigated as cable jackets. While flame retarded EVA exhibited no dripping during burning, TPU flame-retarded with MC cables showed pronounced melt-dripping. Cone calorimeter tests were carried out using cable rafts as well as our self-made cable module test, simulating a vertical bundle of cables at the bench scale. The comparison of different fire tests, different exposure conditions, and different materials carved out the specific degradation phenomena with respect to each of these parameters. Most of this work was supported by the IGF Project (18926 N) of the Fördergemeinschaft für das Süddeutsche Kunststoff-Zentrum e.V., supported by the AiF within the framework of the program “Förderung der Industriellen Gemeinschaftsforschung (IGF)” of the German Federal Ministry for Economic Affairs and Energy based on a decision of the Deutschen Bundestag. T2 - 33rd Polymer Degradation Discussion Group Conference (PDDG-2019) CY - St. Julian, Malta DA - 01.09.2019 KW - Weathering resistance KW - Durability KW - Flame retardancy PY - 2019 AN - OPUS4-49020 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Aris, Stephan T1 - Konformitätsbewertung von ortsbeweglichen Druckgeräten - speziell Treibgasflaschen - nach Richtlinie 2010/35/EU (TPED) N2 - Im Vortrag wird auf die rechtlichen Grundlagen der Richtlinie 2010/35/EU eingegangen. Dies umfasst die Definition von ortsbeweglichen Druckgeräten, die an sie gestellten technischen Anforderungen und die Anforderungen an deren Konformitätsbewertung. Des Weiteren wird die Anwendung der Richtlinie auf Feuerlöscher und deren Treibgasflaschen sowie die damit verbundenen Probleme in der Praxis diskutiert. T2 - Fortbildung GRIF CY - Prichsenstadt, Germany DA - 11.09.2019 KW - Ortsbewegliche Druckgeräte KW - Treibgasflaschen KW - Tragbare Feuerlöscher KW - TPED KW - ADR KW - Konformitätsbewertung PY - 2019 AN - OPUS4-49024 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jonietz, Florian T1 - Standardisierung eines thermografischen Verfahrens zur Schichtdickenbestimmung von Beton-Oberflächenschutzsystemen N2 - Polymerbeschichtungen auf Beton bieten einerseits mechanischen Schutz vor Beschädigungen und verhindern das Eindringen von Wasser, gelösten Salzen und CO2 und können andererseits der Oberfläche ein gewünschtes Aussehen geben. Daher werden sie in der Bauindustrie insbesondere bei Brücken und Parkhäusern häufig verwendet. Für die beabsichtigte Wirkung der Beschichtung ist deren Schichtdicke ein entscheidender Faktor und muss daher nach Aufbringung der Schicht und im Betrieb regelmäßig überprüft werden. Üblich sind hier zerstörende Verfahren mit nachträglich erforderlicher Ausbesserung. Im Rahmen eines Vorgängerprojektes wurde an der BAM in Kooperation mit der IBOS GmbH ein zerstörungsfreies Verfahren entwickelt, welches auf aktiver Thermografie basiert. Ein Prototyp mit Halogenlampe und Infrarot-Kamera wurde erprobt. Das hier beschriebene Folgeprojekt hat das Ziel, dieses Verfahren zu standardisieren, damit es sich in der Industrie als zerstörungsfreies Alternativverfahren zur Schichtdickenbestimmung durchsetzt. Im ersten Schritt wird gezeigt, bei welchen Oberflächenschutzsystemen das Verfahren bereits zuverlässige Schichtdickenmessungen ermöglicht und praxistauglich ist. Anschließend werden weitere Forschungsthemen definiert und bearbeitet, die eine Anwendung für alle Oberflächenschutzsysteme ermöglichen sollen. Besondere Herausforderungen stellen etwa Sandeinstreuungen in der Polymerschicht dar. Auch muss der Frage nach der Anwendbarkeit auf Mehrschichtsysteme nachgegangen werden. Des Weiteren stellt sich die Frage nach dem Einfluss der Beschaffenheit des Betonuntergrunds auf die Anwendbarkeit des Verfahrens. Im zu erarbeitenden Normentwurf sollen diese Untersuchungen die Möglichkeiten, aber auch die Grenzen der aktiven Thermografie zur Schichtdickenmessung von Oberflächenschutzsystemen aufzeigen. Im Beitrag werden die systematischen Untersuchungen bezüglich dieser Fragestellungen dargelegt. T2 - DACH-Jahrestagung 2019 CY - Friedrichshafen, Germany DA - 27.05.2019 KW - thermografisches Verfahren KW - Standardisierung KW - Schichtdickenbestimmung KW - Beton-Oberflächenschutzsysteme KW - Polymerbeschichtungen auf Beton PY - 2019 AN - OPUS4-49008 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schwarz, Silke T1 - Abstände nach KAS-18 (TA Abstand) und 2. SprengV - Auswirkungen auf die Explosivstoffindustrie N2 - Darstellung der angemessenen Abstände und Schutzobjekte nach KAS-18 und BImSchG im Vergleich zur 2. SprengV. Ausführungen zu Auswirkung auf die Explosivstoff-Industrie T2 - BGRCI Erfahrungsaustausch CY - Gut Ising, Germany DA - 12.09.2019 KW - KAS-18 KW - Angemessene Abstände KW - BimSchG KW - Schutzabstände nach 2. SprengV PY - 2019 AN - OPUS4-49014 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sklorz, Christian T1 - Fire protection systems for above ground storage tanks N2 - Liquefied propane gas (LPG) tanks in a fully engulfing accidental fire experience a fast increase in internal pressure. The result is often a Boiling Liquid Expanding Vapor Explosion (BLEVE) that can result in a large fireball and flying debris over a radius of more than 100 meters. In the last 30 years BAM has carried out more than 30 real scale fire tests on propane storage vessels across three test sites. The primary research goal was to identify systems that can delay or prevent a BLEVE. Early studies started with water deluge systems, and have since moved on to consider alternative protection systems. It has been shown that an unprotected vessel fails within 10 minutes or less. Tests with different oil and propane fueled fires have given an overview on possible real accidents involving full-engulfing scenarios. LPG tanks of various sizes (2.7 m³, 3.6 m³, 4.8 m³, 6.7 m³) were used with different filling levels. Numerous protection systems, ranging from active systems like water systems to passive thick- and thin-film layers. Also, the degree of thickness of these layers was variated. Pressure relief valves (PRV) have also been investigated, both alone and in combination with protection systems. This paper gives an overview of the work performed by BAM in the field of BLEVE prevention of protecting system since the last 30 years. It has been shown that e.g. with a full applied coating degree on the tank with and without PRV can be reached an exposition in a test fire scenario a duration of more than 60min. For partly coated tanks with and without PRV the duration time is like an unprotected vessel. Furthermore, it could be shown that the active water system also protects with technically correct design. T2 - Loss Prevention 2019 CY - Delft, The Netherlands DA - 16.06.2019 KW - Fire protection systems KW - Popane storage tanks PY - 2019 AN - OPUS4-49022 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Michael-Schulz, Heike T1 - Classification of peroxyacetic acids N2 - Review of classification of peroxyacetic acids according to the legal regulations of chemicals substances and dangerous goods. T2 - IGUS EOS Meeting CY - Brussels, Belgium DA - 21.05.2019 KW - Einstufung von Peressigsäuren PY - 2019 AN - OPUS4-49015 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grunewald, Thomas T1 - Nichtelektrischer Explosionsschutz: Zündgefahren durch Funken - Grundlagen und Maßnahmen zum Explosionsschutz N2 - Bei Geräten und Maschinen zur bestimmungsgemäßen Verwendung in explosionsgefährdeten Bereichen muss in der europäischen Union eine Zündgefahrenbewertung durchgeführt werden. Dabei müssen unter anderem die Gefahren von nichtelektrischen Zündquellen betrachtet werden, zu denen auch die mechanischen Schlagvorgänge gehören. Bei Schlagvorgängen kommt es infolge des Zusammenstoßes zweier Werkstücke zu einer Umwandlung der kinetischen Energie. Dabei erhöht sich die Temperatur der Werkstoffe an der Kontaktstelle und es kommt unter Umständen zu einem Abtrennvorgang kleiner Partikel erhöhter Temperatur. Sowohl die heißen Kontaktstellen als auch die abgetrennten Partikel können eine wirksame Zündquelle für ein explosionsfähiges Gasgemisch darstellen. Zur Festlegung von Grenzwerten wurden in der Norm EN 13463-1:2009 die Gasgemische anhand ihrer Explosionsgruppe klassifiziert und zu jeder Gruppe die maximale Energie des Schlagvorgangs festgelegt, unter derer die Entstehung einer wirksamen Zündquelle als unwahrscheinlich angenommen werden kann. T2 - Ausbildung zum Explosionsschutzbeauftragten (Veranst.-Nr. H050-08-064-9), Haus der Technik (HdT) - Außeninstitut der RWTH Aachen und der Universität Duisburg-Essen CY - Timmendorfer Strand, Germany DA - 20.08.2019 KW - Mechanisch erzeugte Funken KW - Nichtelektrische Funken KW - Nichtelektrischer Explosionsschutz KW - Schlagfunken KW - Funken PY - 2019 AN - OPUS4-49026 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Robens-Radermacher, Annika T1 - Efficient reliability analysis by combining uncertain measurement data, Bayesian model updating and reduced order modeling N2 - The efficiency of structural model updating and the subsequent reliability analysis is increased by using the advantages of reduced order models. Coupling a reduced model of the structure of interest with a Bayesian model updating approach or an reliability analysis to estimate the failure probability reduce the computational cost of such complex analyses drastically. T2 - 8th Workshop on High-Dimensional Approximation (HDA) 2019 CY - Zurich, Switzerland DA - 09.09.2019 KW - Reduced order modeling KW - Bayesian model updating PY - 2019 AN - OPUS4-49035 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stelzner, Ludwig T1 - Transport and reconfiguration of moisture in HPC due to unilateral heating N2 - Explosive spalling is caused by, among others, the thermohydraulic spalling mechanism. During this process, vaporization, dehydration, moisture-transport and condensation processes interact. As a result, a drying and dehydration zone as well as a saturated zone, known as a moisture clog, are observed inside the unilaterally-heated concrete. The presented research is focused on the experimental investigation of the underlying thermohydraulic processes. To investigate these, a test methodology based on X-ray computed tomography (CT) and nuclear magnetic resonance (NMR) was developed. Thereby, the X-ray CT scans are carried out simultaneously during the application of a defined unilateral-heating regime on a specially-constructed specimen. This miniaturized specimen, equipped with a double-layer casing, reproduces the condition within a planar, unilaterally-heated building component. A preliminary test methodology and the first experimental results were presented at the 5th International Workshop on Concrete Spalling in Borås, Sweden (2017). The contribution for the upcoming workshop presents an improved version of this test methodology and new results for a high-performance concrete (HPC) mixture exposed to temperatures up to 500 °C. Regarding the CT measurements, a higher time-resolution of 15 min was achieved and a quantification of the moisture changes was implemented. Due to an increase in signal quality of the NMR measurements, a pore-size specific moisture distribution can now be resolved. This allows to conclude about the moisture reconfiguration between small gel pores and larger interhydrate pores. Additionally, the NMR measurement are no longer limited to first 2.5 cm below the heated surface but a one-dimensional moisture distribution can now be estimated over the whole 10 cm long specimen. The presented results demonstrate that the combination of X-ray CT and NMR measurements enables to image and quantify the thermally-induced moisture transport and reconfiguration from small gel pores up to macro pores. This provides important insights into the thermohydraulic damage mechanism and leads to a better understanding of spalling avoidance strategies, like the addition of polypropylene fibres. T2 - 6th International Workshop on Concrete Spalling due to fire exposure CY - Sheffield, UK DA - 19.09.2019 KW - Moisture clog KW - X-ray CT KW - NMR KW - Moisture transport KW - HPC PY - 2019 AN - OPUS4-49159 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wagner, Adrian T1 - Innovation und Sicherheit durch den Einsatz von Duplexstählen in Straßentunneln N2 - Ziel des Projektes ist die Qualifizierung von Duplexstählen in Tunnelbauwerken um die Einsatzmöglichkeiten alternativer nichtrostender Stähle zu den bislang gebräuchlichen rostfreien Edelstählen 1.4404 und 1.4571 zu eruieren. Da Duplexstähle im Vergleich zu austenitischen Stählen über eine doppelt so hohe Festigkeit verfügen, können Bauteile schlanker konstruiert werden, wodurch Material eingespart werden kann. Neben der Wirtschaftlichkeit muss die Dauerhaftigkeit untersucht werden. Dazu wurden speziell konzipierte Wand- und Deckenracks mit unterschiedlichen metallenen Werkstoffen und Oberflächen hergestellt und in den Tunnelbauwerken montiert. Nach bestimmten Auslagerungszeiten von bis zu drei Jahren werden die Proben demontiert und auf ihr Korrosionsverhalten untersucht. Ein weiteres Ziel neben der Qualifizierung der Werkstoffgruppe sind die Reduktion der Instandsetzungs- und Wartungsmaßnahmen der Tunnelbetreiber T2 - 3. Tunnelsymposium in Hallein CY - Hallein, Austria DA - 26.09.2019 KW - Duplex KW - Tunnel KW - Korrosion PY - 2019 AN - OPUS4-49165 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baeßler, Matthias T1 - Impact of environmental based effects on SHM strategies N2 - Anwendungen der Bauwerksüberwachung werden häufig stark von jahreszeitlichen Einflüssen wie Temperaturbeanspruchungen beeinflusst. Der Beitrag diskutiert Probleme und Lösungen zum Umgang mit diesen Einflüssen. T2 - SEMC 2019 CY - Cape Town, South Africa DA - 02.09.2019 KW - SHM Environmental PY - 2019 AN - OPUS4-49163 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vössing, Konrad T1 - Contactless testing of wood-based materials with novel air-coupled ultrasonic transducers N2 - The detection of delamination, rot and cracks causing a decrease of strength in wooden construction elements is a key task for nondestructive testing (NDT). Air-coupled ultrasound (ACU) is used to detect flaws without having to provide contact to the surface or otherwise affect the object. Novel ferroelectric transducers with a high signal-to-noise ratio enable an accurate flaw detection. Transducers made of cellular polypropylene (PP) are suitable for characterizing wood-based materials (WBM) because their extremely low Young’s modulus and low density mean a favorable acoustic impedance for the transmission of ultrasonic waves between the transducer and air. The transducers can be applied during the production of WBM and during its service life. The device enables a fast in-situ recognition of defects with frequencies between 90 kHz and 250 kHz. Measurements can be performed in through transmission for a high resolution or in pulse-echo technique in case of one-sided access at the expense of reduced signal strength. Ultrasonic quality assurance for wood is an important attempt to increase the acceptance of wooden structures and towards sustainability in civil engineering in general. T2 - 21. International Nondestructive Testing and evaluation of Wood Symposium CY - Freiburg, Germany DA - 24.09.2019 KW - Air-coupled ultrasound KW - Defect detection KW - Nondestructive Testing KW - Timber PY - 2019 AN - OPUS4-49170 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Jan P. T1 - Applying a two-layer quadrupole model for quantitative thermography at overload-induced delaminations in GFRP N2 - The applicability of 1D-quadrupole-model on the depth estimation of overload-induced delaminations is tested in this contribution. While classical 1D-methods like Pulsed Phase Transformation and Thermographic Signal Reconstruction determine the depth of a defect by one parameter, a two-layer quadrupole model provides two parameters: depth and thermal resistance. In addition, the convectional losses at the surfaces may be considered. The defect investigated is a large-scale delamination in glass fibre reinforced polymer generated by tension overload. T2 - Advanced Infrared Technology & Applications (AITA) CY - Florenz, Italy DA - 16.9.2019 KW - Aktive Thermographie KW - Nicht-lineare Regression KW - 1D-Simulation KW - GFK PY - 2019 AN - OPUS4-49133 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herrmann, Ralf T1 - Introduction and Current Research in Wind Energy N2 - The EERA Wind is a Joint Program for coordination of research in wind energy. In the subprogram SP7 "Structures, materials and components" BAM introduces its current research topics in the field of on- and offshore wind energy and structural health monitoring. T2 - EERA Joint Program Wind: SP7 WORKSHOP on Structures, Materials and Components CY - Amsterdam, Niederlande DA - 24.09.2019 KW - Offshore KW - Wind energy KW - EERA Joint Program PY - 2019 AN - OPUS4-49203 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Palkowski, Carsten T1 - Dynamic Test Method for Heat Pumps and Air Conditioners N2 - Die bisher üblichen Verfahren zur Bewertung der Effizienz einer Wärmepumpe durch Labormessungen berücksichtigen kaum transiente Zustände. Können dynamische Bewertungsverfahren im Labor ein realistischeres Verhalten im Feld wiederspiegeln und damit zu sinnvolleren Entscheidungen führen? N2 - The commonly used methods for evaluating the seasonal performance of heat pumps in the laboratory do not consider transient conditions. Will dynamic test methods be able to better reflect real-life behavior in the field and thus lead to more appropriate decision-making? T2 - EHPA MCO CY - Brussels, Belgium DA - 10.10.2019 KW - Heat pump KW - Inverter-type air conditioner KW - Seasonal performance KW - Energy label PY - 2019 AN - OPUS4-49270 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baeßler, Matthias T1 - Stability and large deformations of slender structures supported by soil materials N2 - Stabilitätsprobleme und große Deformationen schlanker, vorwiegend stahlbaulicher Strukturen sind in einigen Fällen stark von der Belastung und Stützung der Struktur durch den Baugrund abhängig. Der Vortrag verbindet Forschungsansätze zum Thema. T2 - Colloquium on Geotechnical Engineering CY - KIT Karlsruhe, Germany DA - 26.09.2019 KW - Stability Buckling soil-structure-interaction piles offshore PY - 2019 AN - OPUS4-49162 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Duffner, Eric A1 - Szczepaniak, Mariusz A1 - Schoppa, Andre T1 - Abteilung 3 und Arbeitsbereich „Themenfeld Energie Gase" N2 - Vorstellung der Aufgaben-/Forschungs- und Prüfungsschwerpunkte des Arbeitsbereichs "Themenfeld Energie Gase" T2 - Besuch Expertengruppe der BG RCI CY - BAM Berlin, Germany DA - 15.05.2019 KW - Arbeitsbereichs "Themenfeld Energie Gase" PY - 2019 AN - OPUS4-49199 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Jan P. T1 - Ein Blick unter die Oberfläche von Windkraftanlagen durch Thermografie N2 - Rotorblätter von Windkraftanlagen sind hohen Belastungen ausgesetzt. Nach Jahren der Nutzung können Klebeverbindungen unter der Oberfläche versagen. Thermografie soll die Zustandsüberwachung während der gesamten Lebensdauer verbessern. N2 - Rotor blades of wind power generators are subject to high strains. After years of use, adhesive bonds under the surface may fail. Thermography is intended to improve condition monitoring during the entire service life. T2 - Hannover Messe 2019 CY - Hanover, Germany DA - 1.4.2019 KW - Wiederkehrende Prüfung KW - Thermografie KW - Klebeverbindungen KW - Rotorblatt KW - GFK PY - 2019 AN - OPUS4-49160 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Duffner, Eric A1 - Kriegsmann, Andreas T1 - WP8 - RCS standardisation work N2 - Achievements and next steps within WP8 "RCS standardisation work" in the TAHYA Project. T2 - TAHYA Meeting PSB#2 CY - Saarburg, Germany DA - 11.06.2019 KW - TAHYA project PY - 2019 AN - OPUS4-49190 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Duffner, Eric A1 - Szczepaniak, Mariusz T1 - Pressure cylinders for the transport of dangerous goods N2 - Introduction of the Department 3 and the competence and scientific focus of the working group focus area energy - gases for external visitors. T2 - Besuch einer Studentengruppe der AGH Krakau CY - BAM Berlin, Germany DA - 23.09.2019 KW - Introduction Department 3 KW - Focus area energy gases PY - 2019 AN - OPUS4-49193 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Duffner, Eric T1 - System validation and safety aspects N2 - Overview of the achievements, issues and next steps with in TAHYA Project for WP5 T2 - TAHYA meeting PSB#2 CY - Saarburg, Germany DA - 11.06.2019 KW - TAHYA Project PY - 2019 AN - OPUS4-49188 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Duffner, Eric A1 - Kriegsmann, Andreas A1 - Szczepaniak, Mariusz T1 - WP5 - System validation phase and safety aspects N2 - Objectives, tasks, achievements, ongoing work and next steps within WP5 in the TAHYA Project during the first 18 month T2 - TAHYA Midterm review meeting CY - Brüssel, Belgium DA - 26.10.2019 KW - TAHYA project PY - 2019 AN - OPUS4-49192 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Quercetti, Thomas T1 - Package testing of a dual purpose cask for SNF from german research reactors N2 - A new dual purpose cask design was developed for the safe transport and interim storage of spent fuel elements of German research reactors. In the framework of the safety assessment within the licensing procedure the Bundesanstalt für Materialforschung und –prüfung (BAM) as competent authority performed a series of drop tests according to the IAEA-Regulations. The package consists of a cylindrical thick-walled ductile cast iron cask body closed by a double lid system with metallic seals. A lid and bottom sided impact limiter consisting of a wood/steel construction limit the mechanical impact loading. The full-scale test specimen was equipped with a basket and assembled with dummy-fuel elements. The package and test specimen, respectively have a total mass of approximately 24 metric tons. The mechanical test program included three 9m free drop tests, in horizontal, vertical and oblique cask orientation onto the lid system. Additionally, a 1m-puncture drop test followed the horizontal drop test to consider an IAEA-test sequence. The horizontal and vertical drop tests were performed at a temperature of minus 40°C. During the oblique drop test the upper impact limiter was heated to +80°C. The tests were conducted onto an unyielding target, fulfilling the requirements of the IAEA regulations. The test specimen was considerably instrumented with strain gauges and accelerometers. Transient strains at selected locations of the inner and outer container walls, of the primary and secondary lid, as well as of the corresponding lid bolts were measured during the drop tests. Furthermore, decelerations in different locations at the cask body and the lids were measured. The complex geometrical deformation of the impact limiters due to the impact were determined by optical 3d- measurements using the projected fringe method in combination with multi-image photogrammetry. Before and after the drop tests the leakage rate of the lid system was determined by helium leakage testing. The experimental results contribute to the evaluation of the package response to mechanical tests, demonstrating safety under normal and accident conditions of transport. Especially to the verification of the dynamic finiteelement model of the package used in the package design safety report. The paper describes the performance of the drop tests, selected test results focusing on the lid screws and the cask body and the deformation of the impact limiters as well as impact kinematics, respectively. T2 - Workshop ORNL/BAM CY - Oak Ridge National Laboratory, TN, USA DA - 11.04.2019 KW - Package testing KW - Drop test PY - 2019 AN - OPUS4-50621 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Quercetti, Thomas T1 - Package testing of a dual purpose cask for SNF from german research reactors N2 - A new dual purpose cask design was developed for the safe transport and interim storage of spent fuel elements of German research reactors. In the framework of the safety assessment within the licensing procedure the Bundesanstalt für Materialforschung und –prüfung (BAM) as competent authority performed a series of drop tests according to the IAEA-Regulations. The package consists of a cylindrical thick-walled ductile cast iron cask body closed by a double lid system with metallic seals. A lid and bottom sided impact limiter consisting of a wood/steel construction limit the mechanical impact loading. The full-scale test specimen was equipped with a basket and assembled with dummy-fuel elements. The package and test specimen, respectively have a total mass of approximately 24 metric tons. The mechanical test program included three 9m free drop tests, in horizontal, vertical and oblique cask orientation onto the lid system. Additionally, a 1m-puncture drop test followed the horizontal drop test to consider an IAEA-test sequence. The horizontal and vertical drop tests were performed at a temperature of minus 40°C. During the oblique drop test the upper impact limiter was heated to +80°C. The tests were conducted onto an unyielding target, fulfilling the requirements of the IAEA regulations. The test specimen was considerably instrumented with strain gauges and accelerometers. Transient strains at selected locations of the inner and outer container walls, of the primary and secondary lid, as well as of the corresponding lid bolts were measured during the drop tests. Furthermore, decelerations in different locations at the cask body and the lids were measured. The complex geometrical deformation of the impact limiters due to the impact were determined by optical 3d- measurements using the projected fringe method in combination with multi-image photogrammetry. Before and after the drop tests the leakage rate of the lid system was determined by helium leakage testing. The experimental results contribute to the evaluation of the package response to mechanical tests, demonstrating safety under normal and accident conditions of transport. Especially to the verification of the dynamic finiteelement model of the package used in the package design safety report. The paper describes the performance of the drop tests, selected test results focusing on the lid screws and the cask body and the deformation of the impact limiters as well as impact kinematics, respectively. T2 - IHLWM 2019 CY - Knoxville, TN, USA DA - 14.04.2019 KW - Package testing KW - Drop test PY - 2019 AN - OPUS4-50620 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thomas, Sebastian T1 - WP8 RCS standardisation work, probabilistic safety assessment & statistic - PSB meeting #3 N2 - Achievements within WP8 in the TAHYA Project during the month 18 to 24, including ongoing work and next steps. Including safety definition, introduction to probabilistic Approach, failure rate, consequence and risk Definition, introduction monte-carlo-Simulation. T2 - TAHYA PSB meeting 3 CY - Berlin, Germany DA - 28.11.2019 KW - TAHYA project PY - 2019 AN - OPUS4-50118 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlick-Hasper, Eva T1 - Staubdichtheit von Säcken und FIBC für feste Gefahrgüter - Eine kritische Betrachtung der derzeitigen Regelsetzung und Transportpraxis N2 - In den internationalen Gefahrgutvorschriften ist vorgeschrieben, dass Säcke und flexible Großpackmittel (Flexible Intermediate Bulk Container – FIBC) staubdicht sein müssen. Eine quantitative Definition des Terminus Staubdichtheit, wie in anderen Technikgebieten üblich, ist jedoch nicht gegeben. Auch geeignete Prüfverfahren zum Nachweis der Staubdichtheit sind in den Vorschriften nicht genannt. In der Praxis der stichpunkartigen Kontrollen von Gefahrguttransporten durch die Schwerlastgruppe der Autobahnpolizei Münster werden immer wieder Austritte von pulverförmigen oder körnigen Gefahrgütern aus eigentlich intakten Säcken und FIBC detektiert. Es wird ein Überblick über die im Jahr 2018 festgestellten Gefahrgutaustritte aus diesen Gefahrgutverpackungen sowie eine systematische Einordnung hinsichtlich betroffener Bauarten und möglicher Ursachen gegeben. Bei der Stofffreisetzung aus intakten Gefahrgutverpackungen liegt ein mechanischer Transport von Partikeln durch Leckkanäle, z. B. im Verschluss-, Naht- oder Wandungsbereich, vor. Generell kommen zwei Freisetzungswege in Frage: Einerseits eine Langzeit-Freisetzung während des Transports, hervorgerufen durch eine kombinierte Wirkung von Stapellast des Füllguts und Transportvibrationen; andererseits eine stoßartige Freisetzung. Auf Grundlage von durchgeführten Untersuchungen hinsichtlich der stoßartigen Freisetzung pulverförmiger Stoffe aus Gefahrgutsäcken werden erste Lösungsansätze hin zu einer Verbesserung der Staubdichtheit von Gefahrgutsäcken und -FIBC vorgestellt. Es wird ein Ausblick auf nachfolgende Arbeiten gegeben. T2 - 48. Jahrestagung der GUS 2019 CY - Stutensee, Ortsteil Blankenloch, Germany DA - 27.03.2019 KW - Gefahrgutverpackungen KW - Staubdichtheit KW - Säcke KW - FIBC PY - 2019 AN - OPUS4-47692 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baensch, Franziska T1 - Frequenzanalyse von Schallemission an einem Stahlrohr unter Biegebeanspruchung N2 - Um ein tieferes Verständnis über die Schallemission bei der Entstehung und Ausbreitung von Rissen in Stahlrohrleitungen zu erlangen, wurde ein Stahlrohr der Güte S355J2H im Vierpunkt-Biegeversuch quasistatisch bis hin zum Wanddurchbruch (Leckage) belastet und mittels Schallemissionsmessung und Gleichstrompotentialmessung überwacht. Das Rohrsegment wurde durch einen 90°- Außenumfangskerb in der Mitte der Rohrlänge definiert vorgeschädigt, um davon ausgehend ein stabiles Risswachstum zu induzieren und die Analyse von Schallemission aus Rissereignissen, die am Kerb eintraten, sicherzustellen. Für die Schallemissionsmessung wurden vier Breitbandsensoren max. 105 mm vom Kerb entfernt montiert. Die Signalaufzeichnung erfolgte kontinuierlich und schwellwertunabhängig. Für die Gleichstrompotentialmessung wurde ein Gleichstrom von 300 A eingeleitet und der Potentialabfall über dem Kerb mit fünf Sonden entlang des Kerbs gemessen. Beide Messverfahren identifizieren die Rissinitiierung sowie Veränderungen im Risswachstum. Die detektierten Schallemissionsereignisse werden, unter Berücksichtigung spektraler Eigenschaften, mit fortschreitender Belastung und Rissentwicklung analysiert. Diese Studien wurden im Rahmen des interdisziplinären Forschungsprojekts AGIFAMOR, Aging infrastructure - Faseroptisches Monitoring von Rohrleitungen, an der BAM durchgeführt. T2 - 22. Kolloquium Schallemission und 3. Anwenderseminar Zustandsüberwachung mit geführten Wellen CY - Karlsruhe, Germany DA - 27.03.2019 KW - Schallemission KW - Frequenzanalyse KW - Rissbildung in Stahl PY - 2019 AN - OPUS4-47690 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Küttenbaum, Stefan T1 - Non-Destructive Testing: A valuable source of information for reliability assessments N2 - The reassessment of bridges is becoming increasingly important. The basic requirement for analyses of structural safety is reliable knowledge about individual structures. This paper introduces the new approach to evaluate the quality of measured data gained from non-destructive testing (NDT) to provide reliable, objective, and relevant information about existing bridges. The purpose is to relate this validated knowledge to probabilistic analyses. Bridging the gap between NDT and numerical reassessments indicates reduced numerical uncertainties and residual service time extensions. This paper deals with an application of this approach using measurement data collected by ultrasonic technique at a prestressed concrete bridge. T2 - IABSE Symposium 2019 CY - Guimarães, Portugal DA - 27.03.2019 KW - NDT KW - Measurement KW - Structural safety KW - Concrete bridges KW - Eexisting structures PY - 2019 AN - OPUS4-47714 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lugovtsova, Yevgeniya T1 - Analyse der Ausbreitung geführter Wellen in einem Mehrschichtverbund zur Zustandsüberwachung von Composite-Druckbehältern N2 - Composite-Druckbehälter werden für Speicherung und Transport von Gasen unter hohem Druck verwendet. Durch die gewichtssparende Struktur, die aus einem dünnwandigem Metallgefäß und Faserverbundwerkstoff-Ummantelung besteht, sind solche Behälter insbesondere für die Luftfahrt- und Automobilindustrie interessant, z.B. als Wasserstoffspeicher. Die Druckprüfung ist ein konventioneller Test, um die Integrität von Metalldruckbehältern zu bewerten. Im Falle des Composite-Druckbehälters könnte eine solche Prüfung jedoch den Faserverbundwerkstoff überbeanspruchen und somit die verbleibende Lebensdauer der getesteten Komponente verringern. Infolgedessen ist es notwendig, Verfahren zur zerstörungsfreien Prüfung und möglicherweise zur Zustandsüberwachung von Composite-Druckbehältern zu entwickeln. Unser Ansatz verwendet geführte Ultraschallwellen und hat das Potenzial, kritische Schäden wie Risse im Metall und Faserbrüche und Matrixrisse in Faserverbundwerkstoff zu detektieren. In diesem Beitrag wurde die Scaled Boundary Finite Elemente Methode benutzt, um die multimodale, geführte Wellenausbreitung in einem Mehrschichtverbund, der aus Metall und Kohlenfaserverbund entsteht, zu analysieren. Das Verfahren ermöglicht die Identifizierung geeigneter Wellenmoden und die Analyse ihrer Interaktion mit verschiedenen Schäden. Diese Kenntnisse sollen für die Entwicklung von Verfahren zur Zustandsüberwachung von Composite-Druckbehältern angewendet werden. T2 - 22. Kolloquium Schallemission und 3. Anwenderseminar Zustandsüberwachung mit geführten Wellen CY - Karlsruhe, Germany DA - 27.03.2019 KW - Wasserstoffspeicher KW - Automobilindustrie KW - SBFEM KW - Faserverbundwerkstoff KW - Ultraschallwellen PY - 2019 AN - OPUS4-47689 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreier, Andy T1 - Comparision of solution approaches for distributed humidity sensing in PFGI-POF N2 - We compare four different sensing solutions suitable for distributed fiber optic humidity sensing in per uorinated graded-index polymer optical fibers (PFGI-POFs). Compared to silica fbers, polymer optical fibers over advantageous beneffits including signifficantly higher break down strain, fracture toughness and humidity sensitivity. Various humidity-related effects in PFGI-POFs have been reported in the last years including measured attenuation and length changes as well as Brillouin frequency and Bragg wavelength shifts. The four aforementioned methods could serve as a basis for distributed and quasi-distributed humidity sensing and are described here closely with an emphasis on plausible cross effects to temperature and strain. The main focus of this paper lies on the comparison of four approaches with regard to method complexity, sensitivity to humidity, spatial resolution, real-time capability and effort to compensate for cross effects. T2 - SPIE 2019 International Symposium on Optics + Optoelectronics: Optical Sensors CY - Prague, Czech Republic DA - 01.04.2019 KW - Polymer optical fibre KW - Distributed sensing KW - Humidity PY - 2019 AN - OPUS4-47741 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tschirschwitz, Rico T1 - Safety in Technology and Chemistry - BAM Focus Area Infrastructure N2 - The poster contains a description of the extensive activities in the focus area infrastructure as well as the unique possibilities for experimentation on the BAM Test Site for Technical Safety. T2 - Informationstag für den 6. Anruf im EU-Programm "Sichere Gesellschaften - Horizont 2020" CY - Bonn, Germany DA - 21.03.2019 KW - Großversuche KW - Explosionsschutz KW - BAM TTS KW - BAM Test Site for Technical Safety PY - 2019 AN - OPUS4-47736 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Patrick T1 - Untersuchungsmethoden klimatisch belasteter Bauteile - Projektupdate BAM N2 - Kontinuierliche Sensorbasierte Bauwerksmessungen leisten einen wichtigen Beitrag zur Sicherheit von Verkehrsbauwerken. Hierzu werden im Vorhaben AISTEC Referenzbauwerke und Referenzverfahren untersucht mit Schwerpunkt auf den Einfluss klimatischer Bedingungen. Der Vortrag stellt den aktuellen Projektstand des FB 7.2 vor. T2 - Erstes Verbundtreffen AISTEC CY - Weimar, Germany DA - 21.03.2019 KW - Structural Health Monitoring KW - Environmental Effects KW - Climate Chamber KW - Brücken KW - SHM KW - Klimakammer PY - 2019 AN - OPUS4-47702 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grunewald, Thomas T1 - Gebrauch von Werkzeugen im explosionsgefährdeten Bereich - Grundlagen zur Zündquelle mechanisch erzeugte Funken - Möglichkeiten und Grenzen bei der Verwendung von NE-Metall und Edelstahl im Ex-Bereich N2 - Bei Geräten und Maschinen zur bestimmungsgemäßen Verwendung in explosionsgefährdeten Bereichen muss in der europäischen Union eine Zündgefahrenbewertung durchgeführt werden. Dabei müssen unter anderem die Gefahren von nichtelektrischen Zündquellen betrachtet werden, zu denen auch die mechanischen Schlagvorgänge gehören. Bei Schlagvorgängen kommt es infolge des Zusammenstoßes zweier Werkstücke zu einer Umwandlung der kinetischen Energie. Dabei erhöht sich die Temperatur der Werkstoffe an der Kontaktstelle und es kommt unter Umständen zu einem Abtrennvorgang kleiner Partikel erhöhter Temperatur. Sowohl die heißen Kontaktstellen als auch die abgetrennten Partikel können eine wirksame Zündquelle für ein explosionsfähiges Gasgemisch darstellen. Zur Festlegung von Grenzwerten wurden in der Norm EN 13463-1:2009 die Gasgemische anhand ihrer Explosionsgruppe klassifiziert und zu jeder Gruppe die maximale Energie des Schlagvorgangs festgelegt, unter derer die Entstehung einer wirksamen Zündquelle als unwahrscheinlich angenommen werden kann. T2 - Fachtagung Explosionsschutz für Einsatzleiter und Betreiber CY - Linde Material Handling, Aschaffenburg, Germany DA - 24.09.2019 KW - Funken KW - Mechanisch erzeugte Funken KW - Nichtelektrische Funken KW - Nichtelektrischer Explosionsschutz KW - Schlagfunken PY - 2019 AN - OPUS4-49184 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stajanca, Pavol T1 - Investigation of bare and tight buffered optical fibers towards distributed humidity sensing N2 - Humidity is one of principal environmental parameters that plays an important role in various application areas. Distributed humidity/water sensing is sought after in wide range of applications including concrete condition monitoring in civil engineering, SHM of large structures such as dykes or dams, soil moisture measurement in agriculture or leak detection in pipeline or sewage industry. Using humidity-induced strain of specialty hygroscopic coating materials, such as polyimide (PI) seems as the most promising approach so far. In this work, relative humidity and temperature response of different commercial PI-coated and tight-buffer fibers is investigated for the development of distributed humidity sensor. T2 - Seventh European Workshop on Optical Fibre Sensors CY - Limassol, Cyprus DA - 01.10.2019 KW - Distribute fiberoptic sensor KW - Distributed humidity sensing KW - Water ingress detection KW - Optical backscatter reflectometry KW - Tight-buffered fibers KW - Polyimide-coated fibers PY - 2019 AN - OPUS4-49208 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herrmann, Ralf T1 - Vibration Analysis of Structures using a Drone (UAV) based Mobile Sensing Platform N2 - The identification of the dynamic behavior of structures, like bridges and towers, is relevant to address multiple issues. In many cases the dynamic parameters should be acquired only once or at a frequency that doesn’t justify the installation of distinct vibration sensors for a long-term monitoring. To identify modal frequencies of a structure, a drone based mobile sensing platform has been implemented. This sensing platform measures the relative displacement be-tween the structure and the drone, which also shows a strong dynamic behavior under wind tur-bulences. By regarding the dynamic model of the drone and additional measurements at the dis-tance sensor the absolute movement of the structure can be estimated based on the measured relative distance. This time domain data is a suitable input for various operational modal analysis algorithms. The system has been used to identify the dynamic properties of test and real structure, like a 1.5 MW wind turbine tower. T2 - 5th International Conference on Smart Monitoring, Assessment and Rehabilitation of Civil Structures (SMAR 2019) CY - Potsdam, Germany DA - 27.08.2019 KW - Modal Analysis KW - Drone KW - Vibration KW - Wind Turbines KW - Bridges PY - 2019 AN - OPUS4-49205 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sklorz, Christian T1 - Simulation eines Poolfeuers im 1m³ Ofen N2 - Zur Charakterisierung von Brandschutzbeschichtungssystemen für Gas- Lagertanks ist ein Großbrandversuch erforderlich. Zur Ermittlung der produktspezifischen Beschichtungsdicke sind Plattenbrandversuche notwendig. Für Brandprüfungen existieren verschiedene Brandkurven (z.B. ETK, Hydrocarbonkurve, Schwelbrandkurve, BAM-Kurve) um Prüfmuster je nach Anwendungsfall zu zertifizieren. Diese Brandkurven unterscheiden sich hinsichtlich des Temperaturgradienten. Zur Gewährleistung der Übertragbarkeit der BAM-Prüföfen (Kleinprüfstand DIN 4102-8 (Klep) und 1-m³ Ofen) auf die NORM ISO 21843 (2018-09) ist es erforderlich einen Wärmeintrag von 90 – 120 kW/m² in das Prüfmuster zu garantieren. T2 - TF-IF CY - Berlin, Germany DA - 16.09.2019 KW - Brandversuch KW - Fire testing KW - Ofen PY - 2019 AN - OPUS4-49250 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Raysyan, Anna T1 - Lateral Flow ImmunoAssays for the detection of bisphenol A emissions from plastic materials N2 - Bisphenol A (BPA) is a chemical that has been used in the production of plastics for more than 40 years. BPA released from bottles made of polycarbonates has been identified as a potential endocrine disrupting substance. Comprehensive research has been undertaken to test and verify its effect on animals and human beings. Many methods have been proposed for the determination of BPA, in particular, gas and liquid chromatography. The main disadvantages of such approaches are the high cost of the equipment, the significant duration of an analysis, and difficulties in screening a large number of samples. Lateral Flow ImmunoAssay (LFIA) attributes are high throughput, high specificity and sensitivity, as well as low cost and simplicity. An LFIA test strip was developed. This LFIA is based on anti-BPA antibodies (from mouse) conjugated with gold nanoparticles as the marker by passive absorption and covalent coupling, deposited in an elaborate pad. To form control and test zones, anti-mouse antibody and a BVA-BSA conjugate were spotted on the nitrocellulose membrane, respectively. Negative samples are revealed by red lines both in the test and control zones, respectively, whereas positive samples produce a single red line only in the control zone. The measurement range is 0.05 – 23 μg/L, visually detected by the naked eye within 5 minutes. In addition, the intensities at the test line can be read by dedicated lateral flow readers (opTrilyzer® and Cube by opTricon, Berlin) for a more precise and documented determination. T2 - EBS2019 CY - Florence, Italy DA - 18.02.2019 KW - BPA KW - LFIA KW - Plastic PY - 2019 AN - OPUS4-47477 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schliephake, H. A1 - Adam, Christian T1 - CFK-Abfälle als Primärkohleersatz Im Lichtbogenofen bei der Stahlerzeugung N2 - CFK-Abfälle werden trotz der bestehenden Verfahren zur Rückgewinnung der Carbonfasern zukünftig vermehrt anfallen. Für diese Abfälle wird nach technischen Lösungen der energetischen oder stofflichen Verwertung gesucht. Eine Möglichkeit ist die Nutzung der CFK-Abfälle als Primärkohleersatz im Lichtbogenofen bei der Stahlherstellung. T2 - 3. Fachtagung Composite Recycling & LCA CY - Stuttgart, Germany DA - 20.02.2019 KW - Carbonfaser KW - CFK PY - 2019 AN - OPUS4-47438 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dorgerloh, Ute T1 - Short-chain perfluoroalkyl acids: TFA and DFA N2 - Analysis in environmental media and discussion for method standardization in NAW T2 - Normausschuss Wasserwesen CY - Frankfurt a.M., Germany DA - 28.03.2019 KW - TFA KW - DFA PY - 2019 AN - OPUS4-47742 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koerdt, Andrea T1 - Investigation of methanogen-induced microbiologically influenced corrosion (Mi-MIC) using simulated marine environments under flowing conditions N2 - Microbiologically influenced corrosion (MIC) of iron is usually attributed to sulfate-reducing microorganisms (SRM) in offshore industries, such as the oil and gas pipelines, due to the high concentrations of sulfate in the seawater. SRM act upon the metal by the reactiveness of hydrogen sulfide (HS-), and by withdrawal of the available electrons (Fe --> Fe2+ + 2e-; E° = -0.47 V) in electrical contact with the metal (EMIC). However, methanogenic archaea can also cause MIC. Because they do not produce HS-, withdrawal of electrons may be their main corrosive mechanism; however, mechanistic details and kinetics of the overall process are poorly understood. To investigate the corrosion potential of methanogens, we studied the EMIC methanogenic strains isolated from marine sediments (Methanobacterium-affiliated strain IM1) and crude oil tanks (Methanococcus maripaludis Mic1c10), in an in-house developed flow-through cell to simulate a fluctuating environment. A co-culture of M. maripaludis and D. alaskensis was also established to study the effect of syntrophic growth on metal corrosion that may occur in industrial pipelines. Results indicate that the rates of iron corrosion due to coupled methanogenesis (up to 0.4 mm/yr) are higher to that caused by the marine SRM Desulfovibrio alaskensis (0.15 mm/yr). Surface analyses of the metal showed severe pitting with high methane production. Genomic analysis of the EMIC methanogen M. maripaludis Mic1c10 will provide an insight on the mechanisms of MIC. Such knowledge and deeper understanding also from an electrokinetic point of view may not only provide further models in microbial electrophysiology, but also contribute to mitigation strategies in MIC. T2 - VAAM- Annual Conference 2019 of the Association for General and Applied Microbiology CY - Mainz, Germany DA - 17.03.2019 KW - HI-Tension KW - MIC KW - Methanogens KW - Corrosion KW - Sulfate reducing bacteria PY - 2019 AN - OPUS4-47739 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kern, Simon A1 - Wander, Lukas A1 - Meyer, Klas A1 - Guhl, Svetlana A1 - Gottu Mukkula, A. R. A1 - Holtkamp, M. A1 - Salge, M. A1 - Fleischer, C. A1 - Weber, N. A1 - King, R. A1 - Engell, S. A1 - Paul, Andrea A1 - Pereira Remelhe, M. A1 - Maiwald, Michael T1 - Flexible Automation with compact NMR instruments N2 - Modular plants using intensified continuous processes represent an appealing concept to produce pharmaceuticals. It can improve quality, safety, sustainability, and profitability compared to batch processes, and it enables plug-and-produce reconfiguration for fast product changes. To facilitate this flexibility by real-time quality control, we developed a solution that can be adapted quickly to new processes and includes a compact Nuclear Magnetic Resonance (NMR) spectrometer for online quality monitoring as well as a new model-based control approach. The NMR sensor is a benchtop device enhanced to the requirements of automated chemical production including ro-bust evaluation of sensor data. Here, we present alternatives for the quantitative determination of the analytes using modular, physically motivated models. These models can be adapted to new substances solely by the use of their corresponding pure component spectra, which can either be derived from experimental spectra as well as from quantum mechanical models or NMR predictors. Modular means that spec-tral models can simply be exchanged together with alternate reagents and products. Beyond that, we comprehensively calibrated an NIR spectrometer based on online NMR process data for the first time within an industrial plant. The integrated solution was developed for a metal organic reac-tion running on a commercial-scale modular pilot plant and it was tested under industrial conditions. T2 - 7th Annual PANIC Conference CY - Hilton Head Island, South Carolina, USA DA - 03.03.2019 KW - Online NMR Spectroscopy PY - 2019 AN - OPUS4-47715 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wang, Cui T1 - Ratiometric luminescent TOP nanosensors for simultaneously measuring temperature, oxygen, and pH at a single excitation wavelength N2 - Two nanosensors for simultaneous optical measurements of temperature (“T”), oxygen (“O”), and pH (“P”) have been designed. These “TOP” nanosensors are based on 100 nm-sized silica-coated polystyrene nanoparticles (PS-NPs) doped with the near infrared emissive oxygen- and temperature-sensitive chromium(III) complex ([Cr(ddpd)2][BPh4]3 CrBPh4)[1][2] and an inert reference fluorescence dye (Nile Red NR or 5,10,15,20-tetrakis-(pentafluorophenyl) porphyrin TFPP) and are covalently labeled with the pH-sensitive fluorophore fluorescein isothiocyanate (FITC). These emitters can be excited at the same wavelength and reveal distinguishable emission spectra suitable for ratiometric intensity-based and time-resolved studies in the visible and near infrared spectral region. The core-shell nanostructure of these sensors reveals high colloidal stability in various aqueous media. Studies in PBS buffer solutions and in a model body liquid demonstrate the applicability of the TOP nanosensors for optically detecting the three bioanalytically and biologically relevant analytes temperature, oxygen and pH simultaneously at the same position. T2 - 2nd European Biosensor Symposium CY - Florenz, Italy DA - 18.02.2019 KW - Sensor KW - Nanoparticle KW - Nanosensor KW - Fluorescence KW - Oxygen KW - Temperature KW - pH KW - Ratiometric KW - Lifetime KW - NIR KW - Cr(III) complex KW - FITC KW - Dye KW - Environment KW - Medical diagnostics PY - 2019 AN - OPUS4-47700 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koerdt, Andrea T1 - Themenfeld Projekt MIC Mikrobiell beeinflusste Korrosion N2 - Mikrobiell beeinflusste Korrosion (MIC) ist ein Themenfeldprojekt innerhalb der BAM. Das Spektrum der Materialien und der Organismen ist ernorm. In dem Themenfeldprojekt MIC wurden ausgewählte Bereiche tiefergehend untersucht. In der Präsentation werden die Hauptschwerpunkte dargestellt. T2 - Beirat Material CY - Berlin, Germany DA - 03.04.2019 KW - MIC KW - Kraftstoffabbau KW - Kraftstoffbehälter KW - Gesteinskorrosion KW - Metallkorrosion KW - HI-Tension PY - 2019 AN - OPUS4-47740 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kotthoff, Lisa T1 - Investigation of the veterinary drug monensin: Simulation and identification of transformation products N2 - The knowledge of transformation pathways and identification of transformation products (TPs) of veterinary drugs is important for health, food and environmental matters. Monensin (MON) is an ionophore antibiotic widely used to cure and prevent coccidiosis by chicken especially in broiler farming. Residues are not only found in food products (chicken and eggs) but also in the environment (manure, soil or water). Several transformation processes can alter the parent compound MON, ranging from biotransformation in living organism to biotic/abiotic and microbial processes in environmental matters. The main objective of this work was to investigate the potential of electrochemistry (EC) to simulate oxidative transformation processes and to predict TPs of MON. An electrochemical reactor was used consisting of a flow-through cell with a glassy carbon working electrode. Derived TPs were analyzed by online coupling of EC and high-resolution mass spectrometry (HRMS) and LC-HRMS offline measurements. Among the generated TPs already known as well as unknown TPs of MON could be found. Additionally, MON was subjected also to other transformation methods such as Fenton reaction, photochemical and hydrolysis experiments as well as metabolism tests with microsomes. As a result, different targeted and suspected TPs could be identified by analysis with LC-HRMS. An overview of detected/identified TPs from this study will be presented in comparison to literature known metabolites and TPs. T2 - ANAKON 2019 CY - Münster, Germany DA - 25.03.2019 KW - Transformation Products KW - Electrochemistry KW - High-resolution MS PY - 2019 AN - OPUS4-47681 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - von Törne, Wipert Jannik T1 - Identifizierung und Charakterisierung technischer Transformationsprodukte von Warfarin N2 - Das Therapeutikum Warfarin ist bis heute der bekannteste Vertreter der antikoagulanten Rodentizide. In dieser Arbeit wurden Phase I Metabolite mittels einer elektrochemischen Durchflusszelle simuliert und analysiert. Weitere Transformations- und Abbauprozesse wurde durch UV-Bestrahlung und Ozonung generiert, gaschromatographisch getrennt und miteinander verglichen. T2 - ANAKON 2019 CY - Münster, Germany DA - 25.03.2019 KW - Warfarin PY - 2019 AN - OPUS4-47733 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tiebe, Carlo A1 - Hofmann, Michael T1 - Monitoring der Ameisensäurekonzentration in Bienenstock-Luft N2 - Die Varroose gilt weltweit als eine der bedeutendsten Erkrankungen der westlichen Honigbiene, Apis mellifera. Verursacht wird sie durch den Ektoparasiten Varroa destructor, der durch Saugen der Hämolymphe und Virenübertragung sowohl die Bienenbrut als auch die adulten Individuen schädigt. Ohne imkerliche Unterstützung gehen betroffene Bienenvölker in der Regel innerhalb von drei Jahren ein. Als bewährte, häufige Behandlung wird flächendeckend 60%ige Ameisensäure (AS) -im Bienenstock appliziert über verschiedene Verdampfungssysteme- eingesetzt. Sie wirkt als einziger zugelassener Wirkstoff gegen die Varroamilbe auch in die verdeckelte Brut hinein und birgt kein Risiko der Resistenzentwicklung. Allerdings ist das therapeutische Fenster, der Bereich zwischen Milbenabtötung und Bienenschädigung, relativ schmal und die tatsächliche AS-Konzentration im Bienenstock stark abhängig von äußeren Einflussfaktoren, wie Temperatur oder Applikationsart. Eine Bestimmung der exakten AS-Konzentration im Bienenstock ist also notwendig, um einerseits das Wirkungsoptimum zu bestimmen und andererseits bei Übersteigen der Maximalkonzentrationen mit Folge-Schädigung der Bienen, ein rechtzeitiges Eingreifen der Imker zu ermöglichen. Die Entwicklung eines Detektors zur Bestimmung der tatsächlichen AS-Konzentration in der Bienenstockluft würde einen großen Fortschritt in den Bereichen der Bienenforschung, der Varroa-Behandlung in der Imkerei, sowie einer gesundheitlich bedenklichen AS-Exposition für den Imker bedeuten. Langfristiges Ziel dieses Projekts ist es, ein mobiles, einfach handhabbares Gerät zur Detektion der AS-Konzentration in der Bienenstock-Luft während einer AS-Behandlung zu entwickeln. Grundlage hierfür bietet ein kommerziell verfügbares Multigassensorsystem (PEN3, AIRSENSE Analytics GmbH, Schwerin). Ziel der beschriebenen Vorversuche ist die generelle Eignungsprüfung des Multigassensorsystems PEN3 zur Detektion der hohen AS-Konzentration in Gasgemischen unter Bedingungen wie sie im Bienenstock während einer AS-Behandlung herrschen. Als Messplatz zur Detektion von AS in Luft wurden zwei Systeme vorbereitet: A) Eine Plexiglasbox mit einem Volumen von ca.1,9 l diente als Prüfkammer, wurde von einem Gasstrom befeuchteter synthetischer Luft durchströmt (50 mL min-1, 100 mL min-1 oder 300 mL min-1) und zur Temperierung auf 25 °C auf einer Heizmatte bzw. auf 35 °C in einem Ofen platziert. AS-Wasser-Gemische verschiedener Volumenverhältnisse (0-100%) wurden in einer Glasschale (Oberfläche Flüssigphase 9,6 cm2) in der Prüfkammer vorgelegt. B) In einer durch eine Heizmatte auf 25 °C temperierten, zwei-zargigen Segeberger Beute wurden vier Messpunkte angebracht (davon drei in der oberen und einer in der unteren Etage) und 60%ige AS über einen Nassenheider-Verdampfer vertikal vorgelegt. Zur Detektion des AS-Luft-Gemischs wurde das PEN3 Multigassensorsystem genutzt. Das zu untersuchende Gasgemisch wurde über die internen zehn Metalloxid-Halbleiterdetektoren (1-10) der PEN3 geleitet. Das so generierte Messsignal beschreibt ein Widerstandsverhältnis zwischen dem Widerstandwert zum Zeitpunkt der Messung (R) und dem elektrischen Widerstand bei der Nullluft-Messung (R0), wobei hier befeuchtete synthetische Luft mit einer reltativen Feuchte von 49 % ± 4 % oder Raumluft genutzt wurde. Gase unterschiedlicher Zusammensetzung können anhand der dargestellten Signalmuster verschiedener Sensoren voneinander unterschieden werden. In beiden Messsystemen wiesen die Sensorelemente 1, 6, 7, 8 und 9 gesteigerte Sensitivitäten beim Vorliegen von Ameisensäure im Gasgemisch auf. Die größten Widerstandsverhältnisse zeigten dabei die Sensorelemente 6, 8 und 9, sodass hier von der höchsten Empfindlichkeit für AS auszugehen ist. Basierend auf den erhobenen Messdatensätzen wurden Hauptkomponenten- (PCA) und lineare Diskriminanzanalysen (LDA) zur Dimensionsreduktion durchgeführt, um charakteristische Muster aus den Messsignalen zu extrahieren. Die PCA- und LDA-Plots für die jeweils bedeutsamsten Komponenten PC 1 und PC 2 bzw. LD 1 und LD 2 eines Versuchslaufs in der Plexiglasbox (A) bei einer Temperatur von 35°C, einem Volumenstrom von 300 mL min-1 und variablen Ameisensäure-Wasser-Volumenverhältnissen von 0 % bis 100 %. Deutlich erkennbar sind die Abhängigkeiten der Komponenten PC 1 und LD 1 (Abszissen) vom vorgelegten AS-Wasser-Volumenverhältnis. Unsere Ergebnisse zeigen, dass das Multigassensorsystem zur Bestimmung von AS in Luft unter ähnlichen Bedingungen wie bei einer AS-Behandlung im Bienenstock angewandt werden kann. Die Versuche zeigen, dass die im PEN3 eingesetzten Metalloxid-Sensoren bzw. Metalloxidsensor-Arrays zur Detektion von AS in Luft auch bei höheren Konzentrationen als beispielsweise der MAK-Wert von 5 µmol/mol zur Überwachung des AS-Gehaltes in Bienenstöcken angewandt werden können. Aufgrund der Möglichkeit der quasi Echtzeit-Messdatengenerierung, der geringen Kosten kommerziell verfügbarer Sensorelemente, der Portabilität und der Möglichkeit zur Miniaturisierung zeichnen sich solche Messsysteme zukünftig durch eine besondere Praxisnähe aus. Diese Erkenntnisse sind Grundlage für eine Verbesserung des Detektionsverfahrens und zur Vorhersage über die Effizienz und Effektivität der Varroha-Milbenbehandlung. T2 - Tierbiochemisches Seminar CY - Freie Universität Berlin, Germany DA - 24.05.2019 KW - Ameisensäure KW - Methansäure KW - Multigassensor KW - Sensorik KW - Biene KW - Imker PY - 2019 AN - OPUS4-48076 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilke, Olaf T1 - Formaldehydmessungen an Holzwerkstoffplatten N2 - Die von der BAM eingekauften Holzwerkstoffplatten (Verlegespanplatten, OSB, Multiplexplatten) verschiedener Hersteller zeigten teilweise hohe Formaldehyd-emissionen unter den Prüfbedingungen nach EN 16516, eine Spanplatte hielt den Grenzwert von 0,1 ppm selbst bei Prüfung nach DIN EN 717-1 nicht ein, dürfte also in Deutschland gar nicht in den Verkauf gelangen. Holzwerkstoffe, die unter den Prüfbedingungen der DIN EN 717-1 die Formaldehydklasse E1 einhalten, können insbesondere bei großflächigem Einsatz im Innenraum zu Überschreitungen des Richtwertes für die Innenraumluft führen. Zusätzlich zur Anpassung des Luftwechsels ist auch der Parameter Beladung bei einer Überarbeitung der Norm anzupassen. In der DIN EN 16516 werden produktspezifische (am Einsatz der Produkte orientierte) Beladungsfaktoren vorgegeben. Für den Einsatz von Holzwerkstoffplatten ergäben sich Beladungen von 0,4 (Boden oder Decke), 1,0 (Wände), 1,4 (Wände plus Boden oder Decke) und 1,8 m²/m³ (Wände, Boden und Decke). Um die realen Bedingungen in modernen Gebäuden abzubilden, ist deshalb eine Beladung von 1,8 m²/m³ für die Prüfkammermessung erforderlich. Hierbei ist darauf hinzuweisen, dass für die Beladung im Referenzraum Möbel nicht berücksichtigt wurden. Damit soll sichergestellt werden, dass die Einhaltung des Schutzniveaus bei realen Innenraumbedingungen auch unter den Randbedingungen eines niedrigen Luftwechsels sowie bei sommerlichen Bedingungen und heutigem Lüftungsverhalten der Menschen soweit wie möglich gewährleistet ist. T2 - 26. WaBoLu-Innenraumtage CY - Berlin, Germany DA - 20.05.2019 KW - Formaldehyd KW - Emissionsprüfkammer KW - DIN EN 16516 KW - DIN EN 717-1 PY - 2019 AN - OPUS4-48065 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin T1 - Mantelverordnung - aktueller Stand N2 - Hintergrund, Inhalt und Ziele sowie aktueller Stand der Mantelverordnung T2 - Thomas Baustoffthemen - Zukünftiges Recycling CY - Jena, Germany DA - 21.02.2019 KW - Mantelverordnung PY - 2019 AN - OPUS4-48074 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tiebe, Carlo A1 - Schütze, A. T1 - Gas sensor characterization and calibration N2 - The lecture about gas sensor characterization and calibration contains the content of 3S: Sensitivity, selectivity and stability, sensor drift, aging and poisoning as well as gas mixing systems for laboratory and field calibration, measurement uncertainty for sensor calibration and traceable calibration of gas sensor systems. T2 - International training course - Low-cost Environmental Monitoring – from sensor principles to novel services CY - Berlin, Germany DA - 09.04.2019 KW - Measurement uncertainty KW - Gas mixing system KW - Sensor drift KW - Sensor aging and poisoning PY - 2019 AN - OPUS4-47850 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koerdt, Andrea T1 - Investigation of methanogen-induced microbiologically influenced corrosion (Mi-MIC) using simulated marine environments under flowing conditions N2 - Microbiologically influenced corrosion (MIC) of iron is usually attributed to sulfate-reducing microorganisms (SRM) in offshore industries, such as the oil and gas pipelines, due to the high concentrations of sulfate in the seawater. SRM act upon the metal by the reactiveness of hydrogen sulfide (HS-), and by withdrawal of the available electrons (Fe --> Fe2+ + 2e-; E° = -0.47 V) in electrical contact with the metal (EMIC). However, methanogenic archaea can also cause MIC. Because they do not produce HS-, withdrawal of electrons may be their main corrosive mechanism; however, mechanistic details and kinetics of the overall process are poorly understood. To investigate the corrosion potential of methanogens, we studied the EMIC methanogenic strains isolated from marine sediments (Methanobacterium-affiliated strain IM1) and crude oil tanks (Methanococcus maripaludis Mic1c10), in an in-house developed flow-through cell to simulate a fluctuating environment. A co-culture of M. maripaludis and D. alaskensis was also established to study the effect of syntrophic growth on metal corrosion that may occur in industrial pipelines. Results indicate that the rates of iron corrosion due to coupled methanogenesis (up to 0.4 mm/yr) are higher to that caused by the marine SRM Desulfovibrio alaskensis (0.15 mm/yr). Surface analyses of the metal showed severe pitting with high methane production. Genomic analysis of the EMIC methanogen M. maripaludis Mic1c10 will provide an insight on the mechanisms of MIC. Such knowledge and deeper understanding also from an electrokinetic point of view may not only provide further models in microbial electrophysiology, but also contribute to mitigation strategies in MIC.zeige weniger T2 - Dechema CY - Berlin, Germany DA - 09.04.2019 KW - Corrosion KW - Corrosion products KW - Methanogens KW - Sulfate reducing bacteria KW - Flow-system KW - Environmental simulation PY - 2019 AN - OPUS4-47853 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seeger, Stefan T1 - Regulatory Trends in the EU for Chemicals and Nanomaterials N2 - The presentation gives an overview on existing and upcoming REACH regulations in the EU concerning nanomaterials. T2 - BAM - JBMIA (Japan Business Machine and Information System Industries Association) Meeting, JBMIA Emissions Working Group Meeting CY - Tokyo, Japan DA - 04.05.2019 KW - Nanomaterials KW - REACH KW - EU regulations PY - 2019 AN - OPUS4-47814 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogler, M. T1 - Sampling and Sample Preparation for Analysis of Microplastics in Soils N2 - Despite abundant evidence of the occurrence of microplastics (MP) – these are particles smaller 5 mm – in aquatic environments, little is known about the accumulation of plastic in terrestrial environments, especially in soils. Possible major input pathways could be the use of plastic mulching, the use of compost, sewage sludge or residues from biogas facilities as fertilizers, as well as littering in urban areas. To estimate the MP pollution, the development of reliable, fast methods for sampling, sample preparation, and detection is needed. The obtained data must be representative of the sampled environmental compartment and measurements from different environmental compartments must be comparable. A first breakthrough is an application of ThermoExtractionDesorption-Gas Chromatography-MassSpectrometry (TED-GC-MS) for the detection of MP, including tire abrasives. This method allows the determination of mass content within a few hours and only a minimum of sample preparation for samples from aquatic environments is needed. However, in contrast to filtrate samples from aquatic environments, sediment or soil samples need an enrichment of MP. Whereas MP concentration from marine sediments can be obtained by floatation and density Separation techniques using NaCl solutions, the extraction or separation from soils proves to be more difficult, as plastic particles are often part of organo-mineral aggregates within the soil matrix. The aim of this study is the development of a practicable processing guideline for representatively taken soil samples in order to concentrate microplastics, without complex and time-consuming treatment steps. Dispersants or detergents can be applied to decompose the soil matrix, but each preparation step carries the risk of crosscontamination of the sample and prolongs the preparation procedure. For this reason, we choose ZnCl2-solution with a density of 1.7 g/cm3, which include the densities of relevant MP types (0.9-1.7 g/cm3). It was tested to achieve both, disaggregation and separation as it decomposes organic material and dissolves carbonates. Also, ZnCl2 is inert to the precipitation of undesirable salts and Carbonates during the process of density separation, as polytungstate solution does. ZnCl2 can be reused after stepwise filtering (7 µm, 1.5 µm, 0.7 µm). Thus, disposal costs can be reduced. Efficiency and reproducibility of the sample preparation as well as the degradation behavior of MP under the present conditions were demonstrated with model samples. Real sampling campaigns were conducted at several agricultural sites and floodplains in south-west Germany. The sampling was performed according to practice for soil sampling, using adequate sampling strategies (pattern of sampling, number of field samples, homogenization, etc). The lab sample was fractioned into three size classes (5-100 µm, 100-1000 µm, and 1-5 mm). The identification and determination of mass fraction were done using TED-GC-MS. T2 - EGU 2019 - European Geoscience Union General Assembly 2019 CY - Wien, Austria DA - 07.04.2019 KW - Microplastics KW - Density separation KW - Sample preparation KW - Soil PY - 2019 AN - OPUS4-47824 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hassanein, Yosri-Kamal T1 - Detection of microplastics in compost samples using a thermal decomposition method N2 - The ubiquitous presence of unwanted plastics in the environment, especially microscale particles, has been an issue in scientific studies and public debate in the last years. It is well known that oxidative degradation and subsequent fragmentation, caused by UV-radiation, oxidative aging and abrasion lead to the decomposition of larger plastic products into microplastics (MP). Possible effects of these MP on ecosystems are still unclear. Recent studies on MP findings are focused mainly on aquatic systems, while little is known about MP in terrestrial ecosystems. A possible source of MP input into the soil is compost from domestic bio-waste. Inappropriate waste separation causes plastic fragments in the bio-waste, some of which end up in the compost. In Germany compost is used as fertilizer in agriculture, hence MP could enter the soil by this pathway. So far, there have been only a few studies on this object. For this reason, analysis of compost as a sink and source of MP in ecosystems is of high interest. To estimate and monitor the MP content in compost and soil, fast and harmonised analytical methods are essential, which not only measure the polymer type and number of particles, but also the mass content. The most common spectroscopic methods are very time-consuming, often require complex sample preparation steps and cannot determine mass contents. Therefore, we used ThermoExtractionDesorption-GasChromatography-MassSpectrometry (TED-GC-MS) as a fast, integral analytical technique. The sample is pyrolyzed to 600°C in a nitrogen atmosphere and an excerpt of the pyrolysis gases is collected on a solid phase adsorber. Afterwards, the decomposition gases are desorbed and measured in a GC-MS system. Characteristic pyrolysis products can be used to identify the polymer type and determine the mass contents. This method is well established for the analysis of MP in water filtrate samples. In the present work we optimized the TED-GC-MS method for compost and compost/soil matrix and very common polymers, such as polyethylene, polypropylene, polyethylene-terephthalate and polystyrene (sample mass, detection limits, interfering signals, etc.). Additionally, specific pyrolysis products of polymers used for bio-waste bags, such as polylactide (PLA) and polybutylenadipat-terephthalat (PBAT) had to be identified and evaluated. First measurements were carried out on model and real samples from prepared mixtures and composting plant. The samples were sterilized, fractionated, filtered and dried. In addition, half of the sample material was treated with hydrogen peroxide to investigate a possible effect on detection. T2 - European Geosciences Union (EGU) General Assembly 2019 CY - Vienna, Austria DA - 07.04.2019 KW - Microplastics KW - Compost KW - Detection PY - 2019 AN - OPUS4-47829 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Makowski, Maike T1 - Hot-spots of non-volatile mycotoxins in cereals: How can we overcome this problem? N2 - Since cereals constitute a staple food worldwide, monitoring of growth, storage and processing represent a perseverative challenge of analytical sciences. Especially during storage infested grains breed fungal clusters (“hot spots”) in which mycotoxins accumulate and can highly exceed allowed maximum levels. Because of their unpredictable presence, analytical procedures – including representative sampling - contain invasive and time intensive steps. To avoid erroneously negative results in mycotoxin analysis in cereals, the samples´ homogeneous headspace might be investigated instead of analyzing subsamples of the grains. So-called microbial volatile organic compounds (MVOC´s) provide information for instance about the fungal status of grains. Previous investigations revealed trichodiene to be a precursor of trichothecene mycotoxins which comprises more than 180 different compounds. Due to its non-functionalised sesquiterpene structure, quantification of trichodiene using Headspace GC-MS methods is possible. Thereby, it could be used as biomarker for trichothecene contamination of cereals. Nevertheless, further investigations are necessary. To be able to draw conclusion about the trichothecene content in cereal samples, a possible correlation between trichodiene concentration in the gas phase and trichothecene concentration in the sample must be examined. Realizing this idea would widely extend the applicability of trichodiene and enormously simplify trichothecene detection. Hence, the first step of an ongoing study aims to develop a laboratory reference method using trichodiene as volatile biomarker to quantify trichothecenes in cereals. Both static headspace and SPME-enrichment coupled to gas chromatography with mass spectrometry (GC-MS) were tested and compared. In a second step, this reference method is intended to validate new approaches for fast on-site screening of trichodiene in cereals. T2 - ANAKON 2019 CY - Münster, Germany DA - 25.03.2019 KW - Trichodiene KW - Gaschromatography-Mass Spectrometry KW - Mycotoxin-Biomarker PY - 2019 AN - OPUS4-47847 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Axel T1 - Analysis of microplastics in soil samples by using a thermal decomposition method N2 - While plastics have become indispensable in our daily lives over the last decades, the input into the environment has been increasing concurrently. Plastics often end up in the environment because of intensive use and poor waste management practice. They are subjected to aging and fragmentation and finally be deposited as microplastic particles or in short microplastics (MP). MP are defined as particles originating from synthetic polymers between 1 µm and 5 mm. Although the pervasive abundance of MP in aquatic environments has been demonstrated comprehensively, less is known about the occurrence and fate of MP in terrestrial ecosystems. It is still unclear if soil functions as a MP source or a sink for aquatic environments. MP can either be transported into water bodies by soil erosion or be retained in soils. The few studies published are not comparable because of non-existent harmonized and standardized methods for sampling, sample preparation, and analysis. For an assessment of a potential exposure situation of MP, the determination of a mass content in the soil is crucial. Consequently, spectroscopic methods like Raman or FTIR are not suitable, as they deliver information about the shape and size of individual particles. Therefore, we show the application of ThermoExtractionDesorption-GasChromatography-MassSpectrometry (TED-GC-MS) for MP analysis in the soil. In this method, the soil sample is heated up to 600 °C in a nitrogen atmosphere. The decomposition gases are sorbed on a solid phase, then transferred to a GS-MS system where they are desorbed, separated and identified. The method allows the rapid identification of individual polymers through the detection of specific decomposition products, but also the quantitative determination of the MP mass. Besides thermoplastics, elastomers originated from tire abrasion, can be detected. In the present study, several terrestrial ecosystems in south-west Germany were systematically sampled. Subsequent sample preparation included sieving in fractions of 5-100 µm, 100-1000 µm, and 1-5 mm. MP were extracted by density separation using ZnCl2 solutions. The detection was done by TED-GC-MS measurements. Data of agricultural areas and floodplains are presented exemplarily. A quantitative assessment of highly occurring MP from littering as well as tire abrasion is conducted. T2 - EGU 2019 - European Geoscience Union General Assembly 2019 CY - Wien, Austria DA - 07.04.2019 KW - TED-GC-MS KW - Soil KW - Microplastics KW - Analysis PY - 2019 AN - OPUS4-47822 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seeger, Stefan T1 - Overview on the EMPIR Project "AEROMET" N2 - Overview on the ongoing EU EMPIR Project "AEROMET" Aerosol Metrology for Atmospheric Science and Air Quality, Overview on preliminary resuilts in Workpackages 3 "Calibration of MPSS and CPCs" and 4 "Quantifying airborne particle compositions in the field" T2 - Meeting des ISO TC24/SC4, Joint session of Working Groups 9 "Single particle light interaction methods" and 12 "Electrical mobility and number concentration analysis for aerosol particles" CY - Graz, Austria DA - 11.04.2019 KW - Ambient air pollution KW - EU EMPIR KW - Chemical analysis KW - Total reflection X-ray spectroscopy KW - Airborne Particles PY - 2019 AN - OPUS4-47820 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seeger, Stefan T1 - Instruments for Fine and Ultrafine Particle Emission Characterization N2 - An overview on instruments and methods for the measurement and chemical characterization of particulate emissions from local sources is presented T2 - BAM - JBMIA (Japan Business Machine and Information System Industries Association) Meeting, JBMIA Emissions Working Group Meeting CY - Tokyo, Japan DA - 04.05.2019 KW - Aerosol spectroscopy KW - Particulate emission KW - Chemical analysis KW - Total reflection X-ray spectroscopy KW - Calibration PY - 2019 AN - OPUS4-47816 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -