TY - CONF A1 - Wachtendorf, Volker A1 - Geburtig, Anja A1 - Schulz, Ulrich A1 - Trubiroha, Peter T1 - „Test Tailoring“ eines künstlichen Bewitterungstests am Beispiel der Entwicklung des „Acid Dew and Fog“ Testes N2 - Häufig ist es wünschenswert, für neue Materialien oder Anwendungen künstliche Bewitterungsverfahren zu benutzen, die auf die spezifischen Anforderungen besser zugeschnitten sind, als es bei bestehenden standardisierten Verfahren der Fall ist. Nachdem man die spezifischen Parameter der Beanspruchung unter Anwendungsbedingungen und die spezifische Empfindlichkeit des Materials erfasst hat, beginnt ein Prozess, der als „Test Tailoring“ häufig abstrakt verwendet, auf den aber nur selten näher eingegangen wird. Genau dieser Prozess soll hier am Beispiel der Entwicklung eines künstlichen Bewitterungstests unter saurer Beaufschlagung, dem in der BAM entwickelten Acid Dew and Fog Test, beispielhaft erläutert werden. T2 - 47. Jahrestagung der Gesellschaft für Umweltsimulation (GUS) 2018 CY - Pfinztal (Berghausen), Germany DA - 21.03.2018 KW - Test Tailoring KW - Bewitterung KW - Acid Dew and Fog KW - Umweltsimulation PY - 2018 AN - OPUS4-46542 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Anita T1 - Zulassungsregeln für Verpackungen von Lithiumbatterien N2 - Sicherer Transport defekter Batterien im Aufgabenbereich der BAM. T2 - 12. Fachkonferenz Lithiumbatterien CY - Frankfurt a.M., Germany DA - 21.01.2019 KW - Lithiumbatterien KW - ADR KW - Gefahrguttransport PY - 2019 AN - OPUS4-50803 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thomas, Sebastian A1 - Kriegsmann, Andreas A1 - Duffner, Eric A1 - Szczepaniak, Mariusz T1 - WP8 RCS standardisation work, probabilistic safety assessment & statistic - PSB meeting #3 N2 - Achievements within WP8 in the TAHYA Project during the month 18 to 24, including ongoing work and next steps. Including safety definition, introduction to probabilistic Approach, failure rate, consequence and risk Definition, introduction monte-carlo-Simulation. T2 - TAHYA PSB meeting 3 CY - Berlin, Germany DA - 28.11.2019 KW - TAHYA project PY - 2019 AN - OPUS4-50118 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Duffner, Eric A1 - Wang, Bin A1 - Kriegsmann, Andreas T1 - WP8 RCS standardisation work, Probabilistic safety assessment & statistic N2 - Achievements within WP8 in the TAHYA Project during the first 18 month, including ongoing work and next steps. Including safety definition, introduction to probabilistic Approach, failure rate, consequence and risk Definition, introduction monte-carlo-Simulation. T2 - TAHYA Midterm review meeting CY - Brüssel, Belgium DA - 26.09.2019 KW - TAHYA project PY - 2019 AN - OPUS4-49191 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Duffner, Eric A1 - Kriegsmann, Andreas T1 - WP8 - RCS standardisation work N2 - Achievements and next steps within WP8 "RCS standardisation work" in the TAHYA Project. T2 - TAHYA Meeting PSB#2 CY - Saarburg, Germany DA - 11.06.2019 KW - TAHYA project PY - 2019 AN - OPUS4-49190 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gesell, Stephan T1 - WP8 - RCS standardisation work N2 - The presentation presents a first work premise for the acceptable failrate of a hydrogen pressure vessel. Based on this premise, the basic algorithm for the analysis of given acceptance criteria is presented. T2 - TAHYA PSB Meeting#1 CY - TU Chemnitz, Germany DA - 20.11.2018 KW - FCH JU KW - TAHYA KW - Horizon 2020 KW - Safety assessment PY - 2018 AN - OPUS4-47178 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kriegsmann, Andreas A1 - Duffner, Eric A1 - Szczepaniak, Mariusz A1 - Thomas, Sebastian T1 - WP5 - System validation phase and safety aspects - PSB meeting #3 N2 - Objectives, tasks, achievements, ongoing work and next steps within WP5 in the TAHYA Project from month 18 to 24. T2 - TAHYA PSB meeting 3 CY - Berlin, Germany DA - 28.11.2019 KW - TAHYA project PY - 2019 AN - OPUS4-50113 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Duffner, Eric A1 - Kriegsmann, Andreas A1 - Szczepaniak, Mariusz T1 - WP5 - System validation phase and safety aspects N2 - Objectives, tasks, achievements, ongoing work and next steps within WP5 in the TAHYA Project during the first 18 month T2 - TAHYA Midterm review meeting CY - Brüssel, Belgium DA - 26.10.2019 KW - TAHYA project PY - 2019 AN - OPUS4-49192 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gleim, Tobias A1 - Neumann, Martin A1 - Linnemann, Konrad A1 - Wille, Frank T1 - Welding Seam Safety Evaluation in a Thick-Walled Type B Transport Package N2 - The safety demonstration of heavy weight type B transport packages used for storing spent nuclear fuel (SNF) or radioactive waste is ensured by a combination of physical testing and numerical calculations. While experiments are performed in accordance with the IAEA regulations for selected drop scenarios, Finite-Element-Method (FEM) simulations are used to predict the most damaging case and to investigate additional drop positions. BAM as competent authority in Germany has performed different investigations of a welding seam for a typical large transport package made of A508 forged steel, where the bottom plate is welded to the cylindrical shell. The package has a mass of approx. 120 t. Results of physical drop tests with a full-scale model and accompanying preliminary FEM simulations are presented to determine the decisive stresses in the welding seam. A drop test only represents one set of a package and test parameters. A further parameter analysis is considered to account for allowable variations of packaging properties (e.g. resulting from the manufacturing process) and, based on IAEA requirements, the temperature dependence of the material behaviour. The results of the stress analyses from the drop test and the simulation form the basis and provide the input parameters for a fracture mechanics analysis. In addition to the IAEA specifications, further standards are taken into account for an in-depth investigation, see R6 [1], BS 7910 [2] and API 579-1/ASME FFS1 [3]. All the above-mentioned standards require a manufacturer-specific defect analysis with respect to size and position. Both result from the welding process and the following heat treatment regime. The maximum defect sizes are ensured with non-destructive test methods (such as ultrasonic or particle methods) as integral part of the manufacturing process of the welding seam. Another important parameter in the welding process is the residual stress (secondary stress). The combination of the primary and secondary stress determines the total stress in the welding seam. The most damaging case of the welding seam is determined and evaluated with help of the above-mentioned standards and taking into account the IAEA requirements with respect to defect sizes, material properties, primary and residual stress, yield strength etc. T2 - PATRAM 22 - The International Symposium on the Packaging and Transportation of Radioactive Materials CY - Juan-Les-Pins, France DA - 11.06.2023 KW - Welding KW - Fracture Mechanics KW - Transport Package PY - 2023 AN - OPUS4-57695 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberwein, Robert T1 - Wasserstoff - Kryogene Anwendungen N2 - Wasserstoff wird als ein potenzieller alternativer Energieträger gesehen, mit dem die für 2050 gesetzten Klimaziele erreicht werden könnten. Der Transport von Wasserstoff ist mittels verschiedener Speichertechniken möglich, von denen der kryogene Transport mit den größten volumetrischen Energiedichten einhergeht. Hierdurch eignen sich diese Speicher besonders für die energieintensiven Verkehrsmittel im Land-, See- und Flugverkehr. Im Vortrag werden Speichertechniken, Gefahren im Umgang mit kryogenen Gasen sowie bisherige Störfälle dargestellt. Darauf aufbauend wird ein Teil der aktuellen Forschungsarbeit an der BAM vorgestellt, die die Sicherheit dieser Speicher unter außergewöhnlichen Belastungen adressiert. T2 - 26. Gefahrgutkongress Mecklenburg-Vorpommern CY - Rostock, Germany DA - 03.11.2022 KW - Wasserstoff KW - H2 KW - LNG KW - LH2 KW - Tank PY - 2022 AN - OPUS4-56181 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - John, Sebastian A1 - Jürgen, Auster A1 - Widjaja, Martinus Putra A1 - Duffner, Eric A1 - Mair, Georg T1 - Vorstellung NIP II FORSCHUNGSVORHABEN DELFIN N2 - As a contribution to the national hydrogen strategy, 3.5 years ago, the Delfin research project started with the aim of developing a cost- and material-optimized hydrogen tank design for automotive application. Under the patronage of the National Organization Hydrogen and Fuel Cell Technology (NOW), a consortium consisting of 9 research institutes, component suppliers, engineering service providers and automobile OEMs is processing a wide range of work packages. The focus of BAM research sets on impact testing and safety-related characterization of pressure vessels of different development stages. Furthermore, the implementation of nondestructive testing methods is applied. The presentation shows an overview of the BAM work packages and an extraction of the results generated so far. T2 - SAMPE Feierabendkolloqium CY - Online meeting DA - 15.06.2022 KW - Delfin KW - Wasserstoff KW - Druckbehälter KW - Impact PY - 2022 AN - OPUS4-55349 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Duffner, Eric A1 - Mair, Georg A1 - Sonnenberg, Jost-Peter T1 - Vorhaben Restlebensdauer von Composite-Atemluftflaschen N2 - Vorstellung möglicher Inhalte für ein geplantes Atemschutzvorhaben mit der BG RCI T2 - ESA-Tagung 2019 CY - Lübeck, Germany DA - 02.04.2019 KW - Atemschutz KW - Restlebensdauer KW - Thermische Betriebsbelastungen PY - 2019 AN - OPUS4-47956 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böttcher, Nils A1 - Dayani, Shahabeddin A1 - Markötter, Henning A1 - Bruno, Giovanni A1 - Schmidt, Anita A1 - Krug von Nidda, Jonas T1 - Visualizing the progression of the thermal runaway in lithium-ion-cells by controlled abuse tests at low temperatures N2 - Due to their increasing energy density, lithium-ion-batteries (LIBs) play a key role in the traffic energy transition. Regarding their safety behavior, the main challenge of LIB-cells remains the thermal runaway (TR) process. In situ/operando investigations of the TR on commercial cells is possible with radiographic and computer tomographic measurements. Nonetheless, high resolution visualization of the TR persists as a challenge due to the high progression speed of the TR-process itself. Generally, performing abuse tests at cryogenic temperatures allows to slow down or even prevent the TR. Nevertheless, not all abuse methods are suitable for TR investigations at low temperatures. Nail penetration is an appropriate option, however, contains numerous unknown parameters and therefore suffers regarding reproducibility. Herein, a self-developed high precision nail-penetration-setup is introduced, approaching the necessary mechanically reproducibility with controlled temperatures down to -190°C. The setup allows the preparation of critically abused, however, at cryogenic temperatures stable LIB-cells. These cells were controlled rethermalized to room temperature during synchrotron x-ray computer tomography (SXCT) with a pixel size up to 0.7 μm. During this measurement, the temperature and voltage of the cell is monitored allowing the visualization of the initial internal cell reactions. This study reveals the relation between internal reactions and cell voltage. Finally, the developed set-up enables in-depth analysis of thermal runaway behavior down to material level for various commercial battery cells in the future. T2 - International Battery Safety Workshop CY - Ulm, Germany DA - 28.09.2023 KW - Thermal Runaway KW - Lithium Ion Batteries KW - Computer Tomography PY - 2023 AN - OPUS4-59270 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wienecke, Bernd-Uwe T1 - Verpackungen für Lithiumbatterien N2 - Vortrag über die Auswahl der richtigen Verpackung/Großverpackung für Prototypen, reguläre oder defekte Lithiumzellen/-batterien T2 - Fachkonferenz Lithiumbatterien CY - Frankfurt/Main, Germany DA - 15.01.2018 KW - Lithiumbatterien KW - Prototypen von Lithiumbatterie KW - Defekte Lithiumbatterien PY - 2018 AN - OPUS4-45056 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlick-Hasper, Eva A1 - Bethke, John T1 - Vergleichende Schüttwinkeluntersuchungen nach Vorlagerung bei 23 °C und 50 % r. F. N2 - In den von der BAM anerkannten Prüfstellen kommen derzeit unterschiedliche Methoden der Schüttwinkelmessung zum Einsatz. Es ist unklar, welche dieser Methoden sich prinzipiell für welche Füllgüter eignen. Daher werden derzeit systematische Untersuchungen an der BAM durchgeführt, die im folgenden vorgestellt werden. T2 - 34. Sitzung des BAM AK Prüfstellen CY - Online meeting DA - 28.09.2021 KW - Gefahrgutverpackungen KW - Schüttwinkel KW - Fließfähigkeit KW - Hausner-Faktor PY - 2021 AN - OPUS4-53414 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlick-Hasper, Eva A1 - Bethke, John T1 - Vergleichende Schüttwinkelmessungen an festen Gefahrgütern N2 - Die in den von der BAM anerkannten Prüfstellen für Gefahrgutverpackungen gängigen Schüttwinkel-Messmethoden werden verglichen, anhand der Messung an fünf pulverförmigen oder körnigen Stoffen mit gefährlichen Eigenschaften. Zusätzlich wird die Untersuchung des Einflusses einer unterschiedlichen klimatischen Vorlagerung vorgenommen. T2 - 36. Sitzung des BAM AK Prüfstellen CY - Berlin, Germany DA - 12.09.2023 KW - Schüttwinkel KW - Pulver KW - Schüttgüter KW - Fließfähigkeit PY - 2023 AN - OPUS4-58278 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlick-Hasper, Eva A1 - Bethke, John T1 - Vergleichende Schüttwinkelmessungen - Ausblick auf Untersuchungen der BAM N2 - Es ist bislang noch keine einheitliche Vorgehensweise und kein bestimmtes Prüfverfahren für die Schüttwinkelmessung festgelegt. Bei den Prüffüllgütern handelt es sich nicht nur um gefährliche Ersatzfüllgüter, sondern zum Teil auch um gefährliche Originalfüllgüter. Es liegen noch keine systematische Untersuchungen darüber vor, welche der in den Prüfstellen gängigen Methoden sich prinzipiell für die Anwendung bei bestimmten Extremfällen von Füllgütern eignen. Ziel der Untersuchungen ist daher ein systematischer Vergleich bei der Anwendung verschiedener in den Prüfstellen gängiger Schüttwinkelmessmethoden. T2 - 33. Sitzung des BAM AK Prüfstellen CY - Online meeting DA - 16.09.2020 KW - Gefahrgutverpackungen KW - Schüttwinkel PY - 2020 AN - OPUS4-51248 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlick-Hasper, Eva A1 - Neitsch, Marcel T1 - Vergleichende Fallversuche zur Bewertung von Fallfundamenten - Ausblick auf Untersuchungen der BAM N2 - Oft verfügen Produktionsstätten über bereits verbaute Fallfundamente, die nicht das geforderte Massenverhältnis von 1:50 aufweisen. Gemäß ADR ist jedoch auf dem Niveau der Musterprüfung zu prüfen. Es ist daher fraglich, ob die Prüfungen im Rahmen der Eigenüberwachung und die Baumusterprüfungen vergleichbare Ergebnisse liefern, wenn die Fallfundamente unterschiedlich beschaffen sind. Ziel der Untersuchungen ist daher die Entwicklung eines Untersuchungs- und Prüfkonzepts für bereits verbaute Fallfundamente für Gefahrgutverpackungen im Rahmen einer ingenieurwissenschaftlichen Promotionsarbeit. T2 - 33. Sitzung des BAM AK Prüfstellen CY - Online meeting DA - 16.09.2020 KW - Gefahrgutverpackungen KW - Fallfundamente PY - 2020 AN - OPUS4-51250 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlick-Hasper, Eva A1 - Neitsch, Marcel T1 - Vergleichende Fallversuche zur Bewertung von Fallfundamenten - Ausblick auf Untersuchungen der BAM N2 - Es wird ein Ausblick auf Untersuchungen der BAM gegeben, die im Rahmen einer ingenieurwissenschaftlichen Promotionsarbeit durchgeführt werden sollen. T2 - 40. Sitzung des ERFA Verpackungen CY - Online meeting DA - 05.11.2020 KW - Gefahrgutverpackungen KW - Fallfundamente PY - 2020 AN - OPUS4-51543 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlick-Hasper, Eva A1 - Goedecke, Thomas A1 - Kraume, M. T1 - Vergleich von Worst-Case-Grenzleckageraten mit der Empfindlichkeit des Bubble Test N2 - Der derzeit in den Gefahrgutvorschriften genannte Bubble Test ist keine geeignete Prüfmethode, um für alle Verpackungsvolumina ein Dichtheitsniveau sicherzustellen, welches auf Sicherheitsbetrachtungen unter Beförderungsbedingungen basiert. Für kleinere Verpackungsbauarten müssten theoretisch empfindlichere Prüfmethoden angewandt werden. Auf der anderen Seite sollten Bauartprüfungen für Gefahrgutverpackungen nicht zu kompliziert sein. Daher sollte die Auswahl einer Methode erfolgen, die sowohl eine ausreichende Empfindlichkeit aufweist als auch über eine einfache Art der Durchführung verfügt. T2 - 32. Sitzung des BAM AK Prüfstellen CY - Berlin, Germany DA - 17.09.2019 KW - Gefahrgutverpackungen KW - Dichtheit KW - Bubble Test PY - 2019 AN - OPUS4-48991 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völzke, Holger A1 - Herold, Christian T1 - Verbundvorhaben KoBrA: Ausblick zur Umsetzung von Anforderungen in Technische Behälterkonzepte N2 - Als Ausblick auf noch ausstehende Arbeiten zum Verbundvorhaben "KoBrA" zur Erfassung nationaler und internationaler Anforderungen und Konzepte für Behälter zur Endlagerung wärmeentwickelnder radioaktiver Abfälle in den potentiellen Wirtsgesteinformationen Kristallin, Ton und Salz werden die grundlegenden Anforderungen und Schutzziele der Endlagerbehälter untersucht und der konzeptionelle Weg von Anforderungen hin zu Konzepten erläutert. N2 - Within project "KoBrA" we want to establish the international state of the art in final disposal containers for HLW/SF, and, based on boundary conditions and national legislation, to propose generic final disposal canisters for all three potential host rocks (crystalline rock, clay and salt) for the German high-level radioactive waste. As a preview on activities yet to come, the primary requirements and demands on final disposal canisters are evaluated, and the way to develop container concepts is illuminated. T2 - Fachinformationsgespräch zum FuE-Vorhaben "KoBrA" CY - Berlin, Germany DA - 28.05.2018 KW - Endlagerbehälter KW - Schutzziele KW - Behälteranforderungen KW - Behälterkonzepte KW - Konzeptentwicklung PY - 2018 AN - OPUS4-45470 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herold, Christian A1 - Völzke, Holger A1 - Orellana Pérez, Teresa A1 - Kasparek, Eva Maria A1 - Wolff, Dietmar A1 - Dittrich, Matthias T1 - Verbundvorhaben KoBrA - Arbeitspaket 1 (a) N2 - Im Vorhaben "KoBrA" sollen aus bestehenden Anforderungen für endlagerfähige Behälter und aus internationalen Erfahrungen ein aktueller Stand auf dem Gebiet der Behälterforschung für HLW/SF-Behälter ermittelt und generische Vorschläge für HLW/BE-Endlagerbehälterkonzepte in den drei potentiellen Wirtsgesteinen (Kristallin, Ton oder Salz) erarbeitet werden. N2 - Within Project "KoBrA" we want to establish the international state of the art in final disposal containers for HLW/SF, and, based on boundary conditions and national legislation, to propose generic final disposal canister concepts for all three potential host rocks (crystalline rock, clay and salt) for the German high-level waste. T2 - Fachinformationsgespräch zum FuE-Vorhaben "KoBrA" CY - Berlin, Germany DA - 28.05.2018 KW - Endlagerbehälter KW - Hochaktive wärmeentwickelnde Abfälle KW - Internationale Recherche KW - Arbeitsflussdiagramm PY - 2018 AN - OPUS4-45459 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herold, Christian A1 - Völzke, Holger A1 - Orellana Pérez, Teresa A1 - Dittrich, Matthias A1 - Kasparek, Eva Maria A1 - Wolff, Dietmar T1 - Verbundvorhaben "KoBrA" - Arbeitspaket 1 (b) N2 - Im Vorhaben "KoBrA" sollen aus bestehenden Anforderungen für endlagerfähige Behälter und aus internationalen Erfahrungen ein aktueller Stand auf dem Gebiet der Behälterforschung für HLW/SF-Behälter ermittelt und generische Vorschläge für einen deutschen HLW/BE-Endlagerbehälter in den drei potentiellen Wirtsgesteinen (Kristallin, Ton oder Salz) erarbeitet werden. Im Arbeitspaket 1 wird dafür eine umfassende Literaturrecherche zu internationalen Behälterkonzepten durchgeführt, deren erste Ergebnisse hier präsentiert werden. N2 - Within Project "KoBrA" we want to establish the international state of the art in design and concepts for HLW/SF final disposal Containers. Working package 1, encompassing an extensive literature research on this topic, yielded some preliminary results - promising container concepts - which are presented here. T2 - Fachinformationsgespräch zum FuE-Vorhaben "KoBrA" CY - Berlin, Germany DA - 28.05.2018 KW - Endlagerbehälter KW - Internationale Endlagerkonzepte KW - Hochaktive wärmeentwickelnde Abfälle KW - Final disposal cask PY - 2018 AN - OPUS4-45460 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herold, Christian A1 - Völzke, Holger A1 - Orellana Pérez, Teresa A1 - Dittrich, Matthias A1 - Kasparek, Eva Maria A1 - Wolff, Dietmar A1 - Bollingerfehr, W. A1 - Krone, J. A1 - Prignitz, S. T1 - Verbundvorhaben "KoBrA" N2 - Im Verbundvorhaben "KoBrA" sollen systematisch Randbedingungen, Anforderungen und Konzepte für BE/HLW-Endlagerbehälter in den potentiellen Wirtsgesteinen Kristallin, Ton und Salz gesammelt, zusammengetragen und ausgewertet werden. Am Ende sollen generische Behälteranforderungen und -Konzepte für mögliche endlagerfähige Behälter in Deutschland erarbeitet werden. Hier wird ein Überblick über das gemeinsam mit unseren Partnern von der DBE TEC (jetzt BGE TEC) bearbeitete Gesamtvorhaben mit allen Arbeitspaketen gegeben. N2 - Within Project "KoBrA" we will compile and analyse requirements, demands and concepts for HLW/SF final disposal containers for the potential host rock formations crystalline, clay and salt, and thereby establish proposals for generic final disposal canisters. This poster presentation offers an overview of all work packages we share with our Partners from DBE TEC (now BGE TEC). T2 - Fachinformationsgespräch zum FuE-Vorhaben "KoBrA" CY - Berlin, Germany DA - 28.05.2018 KW - Projektvorhaben KW - Endlagerbehälter KW - BGE TECHNOLOGY KW - Literaturrecherche KW - Endlageranforderungen PY - 2018 AN - OPUS4-45466 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rieck, Arielle A1 - Schwarz, Irina T1 - Valorization of CO2 by electrocatalytic reduction coupled to acetogens via multiple electron carriers (Ecat-acetogens) N2 - For the realization of a sustainable energy economy, it is of great importance to develop CO2 -neutral methods producing multi-carbon organic chemicals used as feedstock in the chemical industry as well as carbon-neutral fuels. A promising method to alleviate the greenhouse effect and thereby forming value-added chemicals or syngas as an energy carrier, is through the electrochemical CO2 reduction reaction (CO2RR). In this work, a bioelectrotechnological approach is developed, in which the CO2RR reaction products (CO and H2) are directly fed to bacteria (acetogens), who use them as “reduction equivalents” to further metabolize CO2 to valuable carbon compounds. Therefore, a bio-electrochemical system consisting of a bioreactor coupled to a CO2 electrolysis cell will be established. Currently, scarce catalysts such as Ag and Au are used as for the CO2RR which may hamper the use of decentral CO2 conversion technology for cost reasons. The technological viability of the bacteria-assisted electrolysis depends on the usage of efficient, biocompatible, and selective electrocatalysts prepared from inexpensive precursors. Porous transition metal and nitrogen co-doped carbons (M-N-Cs) have emerged as precious-metal free electrocatalysts for the direct electrochemical reduction of CO2 into CO and are excellent candidates for scale-up and deployment in technological applications. Furthermore, Co/Ni/Zn functioning as the catalytically active sites will be used, as they are expected to depict non-bactericidal properties in contrast to Cu and Ag catalysts. The non-bactericidal property could e.g., allow for application within the hybrid device (bio-electrochemical system), without the need to separate bacteria and cathode catalyst. The MNCs with the most promising electrocatalytic activity and selectivity will be evaluated in abiotic conditions in the hybrid bio-electrochemical reactor system. T2 - DFG Summer School Workshop CY - Hamburg, Germany DA - 01.09.2022 KW - CO2 Reduktion KW - MNC catalyst KW - Clostridium ragsdalei PY - 2022 AN - OPUS4-56619 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Linnemann, Konrad A1 - Ballheimer, Viktor A1 - Rolle, Annette A1 - Wille, Frank T1 - Update on Work and Meetings in Germany about the Spent Fuel Behavior for Transport and Storage N2 - The presentation gives an update about the work on the spent fuel behavior for transport and storage in Germany. Recent developments and meetings are discussed. In this context the results of the hot cell tests on fuel rod segments performed at JRC in Karslruhe in collaboration with BAM are shown. Furthermore, a new research project about the investigations on potential brittle failure of cladding materials under long-term dry interim storage conditions, which is currently starting at BAM 3.4 is presented. T2 - SNL BAM Workshop CY - Albuquerque, NM, USA DA - 14.03.2018 KW - Spent nuclear fuel KW - Fuel rod behavior KW - Hot cell testing PY - 2018 AN - OPUS4-44865 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völzke, Holger A1 - Wille, Frank A1 - Wolff, Dietmar T1 - Update on the German Spent Fuel Management Strategy N2 - The presentation provides an update on the German spent fuel Management strategy in the areas of transportation, dry interim storage and deep geological disposal. T2 - IAEA 18th TWG-NFCO CY - Online meeting DA - 07.09.2020 KW - Spent nuclear fuel KW - Final disposal KW - Safety KW - Transport and storage cask PY - 2020 AN - OPUS4-51616 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böttcher, Nils T1 - Untersuchungen für den Transport gekühlter Batterien Vorstellung des Nageltests N2 - Im Zusammenhang mit den Untersuchungen zu den Möglichkeiten von gekühlten Transporten von Lithiumbatterien werden unterschiedliche Zerstörungsmethoden vorgestellt und diskutiert. Insbesondere wird dabei das neu entwickelte Nageltool vorgestellt. T2 - Fachkonferenz Lithiumbatterien CY - Goettingen, Germany DA - 28.04.2022 KW - Lithiumbatterien KW - Thermal Runaway KW - Gefahrguttransport KW - Nageltest PY - 2022 AN - OPUS4-56758 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böttcher, Nils T1 - Untersuchungen für den Transport gekühlter Batterien Vorstellung des Nageltests N2 - Im Zusammenhang mit den Untersuchungen zu den Möglichkeiten von gekühlten Transporten von Lithiumbatterien werden unterschiedliche Zerstörungsmethoden vorgestellt und diskutiert. Insbesondere wird dabei das neu entwickelte Nageltool und die vorläufigen Untersuchungen für den Einfluss von Ultratiefkühlung auf unbeschädigte Lithiumbatterien vorgestellt. T2 - ERFA-Verpackungen CY - Berlin, Germany DA - 22.09.2022 KW - Lithiumbatterien KW - Thermal Runaway KW - Gefahrguttransport KW - Nageltest PY - 2022 AN - OPUS4-56759 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weltschev, Margit A1 - Hoffmann, Gabi A1 - Kohl, Anka A1 - Haufe, Manuela T1 - Untersuchungen des Schädigungsgrades von Kunststoffen als Werkstoffe von Heizöllagerbehältern nach einer Nutzungsdauer > 25 Jahre N2 - Heizöllagerbehälter aus Kunststoffen (z.B. Polyethylen) sind für einen sicheren Betrieb von 30 Jahren, dem Zeitraum der Produkthaftung, ausgelegt. Die Tankhersteller empfehlen zur Gewährleistung der Sicherheit nach Ablauf von 30 Jahren den Ersatz dieser Behälter. Kunststoffe unterliegen im Laufe ihrer Nutzungsdauer der Alterung durch die Veränderung ihrer Eigenschaften. Das Ausmaß der Alterung und die Art des Abbauvorganges hängen im Wesentlichen vom chemischen Abbau des Kunststoffes, der Wanddicke des Behälters und den Umgebungsbedingungen ab. Aufgrund der Komplexität der Alterungsvorgänge sind Aussagen zum Langzeitverhalten bzw. zur Lebensdauer der Heizöllagerbehälter ohne geeignete Langzeitprüfungen problematisch. Bisher liegen keine Untersuchungen zum Langzeitverhalten der Kunststoffe vor, insbesondere nach einer Nutzungsdauer über 20 Jahre. In der BDH-Broschüre: Effiziente Systeme und erneuerbare Energien wird darauf hingewiesen, dass ca. 45 % der Heizöllagerbehälter aus Kunststoffen in Deutschland 26 Jahre und älter sind. Viele dieser Tankanlagen sind zudem noch nie von einem Sachverständigen überprüft worden. Schätzungen gehen davon aus, dass mehr als 10.000.000 Tankanlagen aus Kunststoffen in Deutschland vor 1987 errichtet wurden. Ziel der Untersuchungen ist, den Schädigungsgrad der Kunststoffe im Vergleich zu den unbelasteten Werkstoffen zu ermitteln. Da die BAM bis Ende der 80-iger Jahre für die Zulassung dieser Behälter zuständig war, sind die Daten über den eingesetzten Werkstoff für den Vergleich noch vorhanden. Der Bundesverband Lagerbehälter e.V. und das Institut für Wärme und Oeltechnik (IWO) befürworten diese Untersuchungen, um eine Überalterung der Tankanlagen zu vermeiden. Diese Überalterung könnte die zukünftige Gefahr für die Heizöltankanlage sein, nicht der Wettbewerb mit anderen Energieformen. T2 - BUW - Ausgewählte Kapitel der Werkstoffkunde CY - Wuppertal, Germany DA - 12.01.2018 KW - Heizöllagerbehälter KW - Polyethylen KW - Schädigung KW - Lebensdauer PY - 2018 AN - OPUS4-44191 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weltschev, Margit T1 - Untersuchungen des Schädigungsgrades von Kunststoffen als Werkstoffe von Heizöllagerbehältern nach einer Nutzungsdauer > 25 Jahre N2 - Heizöllagerbehälter aus Polyethylenformstoffen werden seit Beginn der 70-iger Jahre in Deutschland hergestellt. Die Hersteller empfehlen zur Gewährleistung der Sicherheit nach Ablauf von 30 Jahren den Ersatz dieser Behälter. Polyethylenformstoffe unterliegen im Laufe ihrer Nutzungsdauer der Alterung durch die Veränderung ihrer Eigenschaften. Das Ausmaß der Alterung und die Art des Abbauvorganges hängen im Wesentlichen vom chemischen Abbau des Polyethylens, der Wanddicke des Behälters und den Umgebungsbedingungen ab. Bisher lagen keine Untersuchungen zum Langzeitverhalten der Polyethylenformstoffe vor, insbesondere nach einer Nutzungsdauer der Tanks über 30 Jahre. Ziel der Untersu-chungen war, den tatsächlichen Schädigungsgrad der Polyethylenformstoffe im Vergleich zu den unbelasteten Formstoffen zu ermitteln. Da die BAM bis Mitte der 90-iger Jahre für die Prüfungen und Gutachten zur Zulassung dieser Behälter zuständig war, sind die Werkstoffdaten noch vorhanden. Als Untersuchungsmethoden wurden die Bestimmung der Schmelze-Masse-Fließrate (MFR) und die Fourier-Transformation-IR-Spektroskopie (FTIR) von Tankausschnitten aus dem Bereich des Bodens, des Mantels und des Daches von 10 ausgesonderten Behältern aus den Polyethylenformstoffen A und B herangezogen. Die Messungen der MFR der Tankaus-schnitte aus diesen Bereichen zeigten Unterschiede in den Werten in Abhängigkeit vom Ge-wicht (5 kg oder 21,6 kg), welches eingesetzt wurde. Eine Abnahme der MFR-Werte wurde für die größere Anzahl der Tankwandungsausschnitte aus dem Formstoff B nach einer Lebensdauer der Tanks > 30 Jahre gemessen. Dieser Formstoff wurde hauptsächlich durch innere Alterung infolge Vernetzungen, Verzweigungen und Weichmacherverlust und weniger durch oxidativen Abbau geschädigt. Die FTIR-Messungen der Proben aus dem Bereich des Bodens und des Mantels der Tanks zeigten, dass die Intensität der asymmetrischen/symmetrischen CH2 -Streckschwingungen im Bereich: 2800 - 2900 cm-1 und der CH2 -Biegeverformungsschwingung bei 1400 cm-1 aufgrund von Kettenspaltungen zugenommen haben. Die Intensität der Carbonylstreckschwingung C=O bei 1740 cm-1 ist niedrig. Sie ist ein Maß für die Oxidation des Polymerwerkstoffes. T2 - Behördenerfahrungsaustausch 2018 CY - Berlin, Germany DA - 04.06.2018 KW - Polyethylen KW - Heizöllagerbehälter KW - Schädigungsgrad PY - 2018 AN - OPUS4-45138 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Anita T1 - Umgang mit defekten Lithiumbatterien - Transport und Lagerung N2 - Während es umfangreiche Transportvorschriften für Lithiumbatterien und auch defekte Lithiumbatterien gibt, gibt es aktuell keine Lagervorschriften. Jedoch sind hier einige Aktivitäten und Ansätze zu verzeichnen, die ebenfalls vorgestellt werden. Ein Schwerpunkt liegt dabei auf e-bike Akkus. T2 - VdS-Fachtagung "Lithium-Batterien: Brand- und Arbeitsschutz" CY - Collogne, Germany DA - 17.09.21 KW - Lithium Batterien KW - Transport KW - Lagerung KW - E-bike Akkus PY - 2021 AN - OPUS4-54180 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Komann, Steffen A1 - Neumann, Martin A1 - Wille, Frank T1 - Transportbehälter für Klasse 7 - Ein Überblick N2 - Die Präsentation gibt einen Überblick über die Tranportbehälter der Klasse 7. Behandelt werden neben der Versandstückklassifikation auch die Anforderungen an diese Verpackungen gemäß der gefahrgutrechtlichen Vorschriften. T2 - 30. Münchner Gefahrguttage CY - Online meeting DA - 20.07.2020 KW - Gefahrgutrecht KW - Transportbehälter KW - Radioaktives Material KW - Zulassungspflichtige Versandstücke PY - 2020 AN - OPUS4-51104 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Anita T1 - Transport von Lithium-Batterien N2 - Im Bereich des Transports von Lithium-Batterien erfüllt die BAM gesetzliche Aufgaben. Diese betreffen insbesondere den Transport von Lithium-Batterien und die entsprechenden zulässigen (und von de BAM zugelassenen) Gefahrgutverpackungen. T2 - Erfa Verpackungen 2018 CY - Berlin, Germany DA - 27.09.2018 KW - Gefahrguttransport KW - Gefahrgutverpackungen KW - Lithium-Batterien PY - 2018 AN - OPUS4-47121 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Anita T1 - Transport von defekten Lithiumbatterien: Umsetzungspraxis der neuen Rechtsvorschriften, Wo besteht Forschungsbedarf? N2 - Transport von defekten Lithiumbatterien - die BAM setzt die Vorschriften des internationalen Gefahrguttransportrechts für defekte Lithiumbatterien um. Um die Kompetenz hierfür sicherzustellen, bedarf es eigener Forschungstätigkeit. Auch im zuständigen UN Gremium werden Untersuchungen durchgeführt, an denen die BAM beteiligt ist. T2 - Fachkonferenz Lithiumbatterien CY - Göttingen, Germany DA - 22.01.2020 KW - Lithiumbatterien KW - Gefahrguttransport KW - ADR PY - 2020 AN - OPUS4-50806 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Martin A1 - Feldkamp, Martin A1 - Linnemann, Konrad A1 - Wille, Frank T1 - Transport of HLW canisters on sea vessels N2 - Germany had been transporting spent fuel to the reprocessing plant in Sellafield and La Hague for decades until around 2005. Resulting from the obligation to take back the vitrified high-level waste from reprocessing six CASTOR® HAW28M filled with 168 canisters with radioactive waste in vitrified form were transported from Sellafield to the interim storage facility Biblis in 2020. Rail wagons were used for the transport to the port in Barrow-in-Furness, where they were loaded into a dedicated seagoing vessel, certified as INF Class 3 according to the INF Code. This was the first time that vitrified high level waste with considerable heat load was transported under a German design approval certificate. BAM was involved in the authority assessment of the conditions for the sea transport. For the first transport BAM required among others, assessment of temperature distribution during transport, logging of temperatures of cargo bays and graphical imaging of temperatures of the bay with the cask in order to ensure compliance with temperature specifications, e.g. maximal neutron absorber and gasket temperatures. Special interest was taken in the identification of possible events exceeding the specified temperatures considering the different philosophies of IMDG code and its supplement INF code regarding temperature control of hatches. Results show compliance with assumed conditions. T2 - RAMTrans 2024 CY - London, GB DA - 14.05.2024 KW - Transport KW - Spent nuclear fuel KW - Ship KW - Sea KW - High level waste PY - 2024 AN - OPUS4-60091 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Karapanagiotis, Christos A1 - Heimann, Jan A1 - Duffner, Eric A1 - Charmi, Amir A1 - Schukar, Marcus A1 - Hashemi, Seyedreza A1 - Prager, Jens T1 - Towards predictive maintenance of hydrogen pressure vessels based on multi-sensor data fusion and digital twin modeling N2 - Hydrogen pressure vessels are among the most essential components for reliable hydrogen technology. Under current regulations, a mostly conservative strategy is employed, restricting the usage time of hydrogen pressure vessels without providing information on the real remaining lifetime. During the service life, pressure vessels are inspected periodically. However, no established method that can provide continuous monitoring or information on the remaining safe service life of the vessel. In this paper, we propose a sensor network for Structural Health Monitoring (SHM) of hydrogen pressure vessels where data from all sensors are collected and centrally evaluated. Specifically, we integrate three different SHM sensing technologies namely Guided Wave ultrasonics (GW), Acoustic Emission testing (AT), and distributed Fiber Optic Sensing (FOS). This integrated approach offers significantly more information and could therefore enable a transition from costly and time-consuming periodic inspections to more efficient and modern predictive maintenance strategies, including Artificial Intelligence (AI)-based evaluation. This does not only have a positive effect on the operational costs but enhances safety through early identification of critical conditions in the overall system in real-time. We demonstrate an experimental set-up of a lifetime test where a Type IV Composite Overwrapped Pressure Vessel (COPV) is investigated under cyclic loading instrumented with AT, FOS, and GW methods. We acquired data from the sensor network until the pressure vessel failed due to material degradation. The data collected using the three different SHM sensor technologies is planned to be evaluated individually, using data fusion, and AI. In the future, we aim to integrate the measurement setup into a hydrogen refueling station with the data stream implemented into a digital signal processing chain and a digital twin. T2 - 11th European Workshop on Structural Health Monitoring CY - Potsdam, Germany DA - 10.06.2024 KW - Hydrogen KW - Ultrasonic guided waves KW - Fiber optic sensors KW - Acoustic emission KW - Machine learning KW - Pressure vessels KW - Structural health monitoring PY - 2024 AN - OPUS4-60277 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Markötter, Henning A1 - Dayani, Shahabeddin A1 - Mishurova, Tatiana A1 - Eddah, Mustapha A1 - Mieller, Björn A1 - Böttcher, Nils A1 - Bruno, Giovanni T1 - Tomographic Imaging Capabilities with hard X-Rays at BAMline (Bessy II) N2 - The BAMline at the synchrotron X-ray source BESSY II (Berlin, Germany) is supporting researchers especially in materials science. As a non-destructive characterization method, synchrotron X-ray imaging, especially tomography with hard X-Rays, plays an important role in structural 3D characterization. The imaging capabilities allow for in-situ and operando experiments. In this presentation the equipment, data handling pipeline as well as various examples from material science are presented. T2 - Correlative Materials Characterization Workshop 2023 CY - Brno, Czech Republic DA - 09.11.2023 KW - Tomography KW - X-ray imaging KW - Li-ion battery PY - 2023 AN - OPUS4-58958 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Qiao, Linan A1 - Keller, Christian A1 - Nagelschmidt, Sven A1 - Wolff, Dietmar T1 - Three-dimensional finite element analysis of O-ring metal seals considering manufacture tolerances N2 - Metal seals are widely used in various industrial branches with severe working conditions (e.g. high pressure, high temperature, corrosion, or radioactive radiation). For example, O-ring metal seals are applied in the closure lid system of transport and storage casks for radioactive materials to guarantee an approved specified leak-tightness and the safe enclosure of the radioactive inventory. Within safety assessments of those casks under normal or accident conditions during transport and long-term interim storage for several decades, numerical simulations of the thermo-mechanical behavior of metal seals by using finite element (FE) analyses are suitable and effective. In general, finite element codes provide the possibility to construct a complex three-dimensional (3D) modelling of metal seals with solid elements, cf., where all components of the metal seals are modeled in detail. This modelling is complex but allows the consideration of underlying physical effects such as elastic-plastic deformation, thermal expansion, creep/relaxation, friction and possible local damage. Therefore, this approach permits the investigation and understanding of the complex behavior of metal seals in detail which can hardly be measured for all seal components. In a prior work, the complex 3D modelling approach was applied to investigate the influence of each seal component on the global seal force by considering varying material properties and different seal diameters. In the present contribution, the influence of manufacturing tolerances is discussed. At first, the results of prior work are summarized. After that, the manufacturing tolerances of the studied O-ring metal seal types are described and the corresponding FE model with all individual components is introduced. Finally, the influence of varying manufacturing tolerances of each seal component on the global seal force is analyzed and discussed. T2 - The 2019 EMI International Conference CY - Lyon, France DA - 3. July 2019 KW - Finite element method KW - Metal seals KW - Material properties KW - Manufacturing tolerances PY - 2019 AN - OPUS4-48448 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Romero-Navarrete, José A. A1 - Otremba, Frank A1 - Betanzo, E. A1 - Obregòn, S. A. T1 - The railway transport sustainability in Mexico N2 - A preliminary analysis has been presented on the advantages for Mexico to migrate the cargo from trucking to railways. While the approach is highly unrealistic, it describes interesting figures that should animate the interest of Mexico to develop its railway infrastructure. Adverse situations due to the topographic characteristics of the mostly populated area of Mexico. The data presented in this paper suggest that the building of railway infrastructure is economically feasible. T2 - CONIIN CY - Queretaro, Mexico DA - 14.05.2018 KW - Railway KW - Transport KW - Mexico PY - 2018 AN - OPUS4-44948 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg A1 - Günzel, Stephan A1 - Bock, Robert T1 - The maximum acceptable consequence limit as a control instrument N2 - The presentation starts with the first agreement of making a national attempt for the introduction of a pV-limit for hydrogen transport. It explains aspects of the technical development, provides an impression of catastrophic incidents, and explains the difference between risk control and consequence limitation. Then the process of determining consequences and the result from the discussion at the UN-WG are explained. The next part summarises the approach for counting the number of impacted persons as a function of the model of pressure wave, the pressure peak, the limits of injured persons and the population density. Finally, the latest state of the discussion and the subsequent recommendations for a pV-value and the adequate phrases for explanation are introduced. T2 - 29th BAM-DIN-IGV-DVFG-Meeting CY - Online meeting DA - 23.02.2022 KW - Hydrogen KW - Pressure recepacles KW - Consequence limit KW - Risk control KW - Population density KW - Pressure wave PY - 2022 AN - OPUS4-54608 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Widjaja, Martinus Putra T1 - The Application of a Reduced Volume Method for the Simulation of the Characterisation of a Carbon Fibre Pressure Vessel N2 - The fibre-break model developed at Mines ParisTech has been able to show the effect of pressurisation rate on pressure vessels. This simulation however had to use a smaller model, as the computation time becomes enormous for simulating a real-scale pressure vessel. Reduced volume method then has been studied on different model configuration. The study showed that the method can be used only on certain configurations. It also gives a positive insight to reduce the computation time. T2 - FiBreMoD Consortium Meeting CY - Leuven, Belgium DA - 18.04.2018 KW - Reduced volume method KW - Integral range KW - Fibre break model KW - Representative volume element KW - Computation time PY - 2018 AN - OPUS4-45638 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Widjaja, Martinus Putra A1 - Joannes, S. A1 - Bunsell, A. A1 - Mair, Georg A1 - Thionnet, A. T1 - The Application of a Reduced Volume Method for the Simulation of the Characterisation of a Carbon Fibre Pressure Vessel T2 - The 18th European Conference on Composite Materials N2 - The developed model has certain limitations of the element size to be used in the simulation to characterise the strength of composite materials. A reduced volume method is proposed in order to reduce the number of degree of freedom of the finite element simulation.This study has revealed certain configuration to be followed to speed up the computation time. T2 - The 18th European Conference on Composite Materials CY - Athens, Greece DA - 24.06.2018 KW - Composite pressure vessel KW - Fibre break KW - Integral range KW - Representative volume element PY - 2018 SP - 1193-892 AN - OPUS4-48927 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Widjaja, Martinus Putra A1 - Joannes, Sebastien A1 - Bunsell, Anthony A1 - Mair, Georg A1 - Thionnet, Alain T1 - The Application of a Reduced Volume Method for the Simulation of the Characterisation of a Carbon Fibre Pressure Vessel N2 - The developed fibre-break model from Mines-ParisTech requires an improvement in terms of calculation time for analysing real-scale model. By implementing the proposed method, the number of representative volume element and monte-carlo run can be optimised to obtain certain confidence level of the results. By reducing this level, faster computation can be done. This approach has given us a positive insight that it can be used for studying real-scale model of composite pressure vessels. T2 - European Conference on Composite Materials 2018 CY - Athens, Greece DA - 25.06.2018 KW - Composite pressure vessel KW - Fibre break KW - Integral range KW - Representative volume element PY - 2018 AN - OPUS4-45563 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Duffner, Eric T1 - TFP COD AGE Schallemissionprüfung N2 - Zwischenstand der Ergebnisse der Schallemissionsprüfungen im Rahmen des TFP COD AGE T2 - 5. Projektmeeting COD AGE CY - BAM Berlin, Germany DA - 13.04.2018 KW - Schallemission KW - Composite-Druckspeicher KW - Degradation PY - 2018 AN - OPUS4-44900 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja T1 - Testing of HDPE containers for dangerous goods after outdoor exposure N2 - Focus areas of BAM as well as testing results of HDPE containers for dangerous goods after outdoor exposure of were presented. T2 - 70th CEEES Meeting CY - Hørsholm, Danmark DA - 13.11.2018 KW - HDPE KW - Dangerous goods KW - Chemical resistance PY - 2018 AN - OPUS4-47032 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wille, Frank A1 - Quercetti, Thomas A1 - Scheidemann, Robert T1 - Test facilities for transport and storage packages at BAM N2 - BAM acts as authority and for service in safety assessment of packages for transport and storage of radioactive materials. We offer extensive test capabilities and application of analytical methods for design verification and simulation for all types of packages for the transport and storage of radioactive materials according with the international IAEA Regulations for the safe transport and for national storage acceptance criteria. BAM operates several test facilities for drop and stacking testing, leak testing and thermal testing. The large drop test tower allows dropping full-scale specimens up to 200,000 kg in any drop orientation as requested. The comprehensive test facilities combined with long-term experience, newest equipment and measurement devices according to the latest state-of-the-art technology ensures realisation of complex test campaigns for package safety evaluation. Beyond that, non-destructive and destructive material test devices and experts are available. Equipment and application of all kinds of typical measurement categories can be offered for testing campaigns. In recent years we performed testing of full-scale type B package models with complex handling and preparation procedures. The results were contributed for different package design approval procedures. Type A packages mainly designed for medical related transport purposes, were continuously tested according to the transport regulations over recent years as well. Moreover, we work on research topics with relevance to package safety. The mechanical behaviour of lid closure systems under transport and storage conditions and the thermal behaviour of impact limiters were recently of special importance for the assessment competencies of BAM and were investigated under use of our test facilities. The paper describes the test facilities and capabilities for package design safety evaluation at BAM and shows examples from our recent work. T2 - PATRAM 2022, 20th International Symposium on the Packaging and Transportation of Radioactive Materials CY - Juan-les-Pins, France DA - 11.06.2023 KW - Transport KW - Drop testing KW - Fire test KW - IAEA KW - Package PY - 2023 AN - OPUS4-58088 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feldkamp, Martin A1 - Quercetti, Thomas A1 - Gleim, Tobias A1 - Wille, Frank T1 - Temperature and Heat Flux Measurements in Fire Testing N2 - Packages for the transport of Spent Nuclear Fuel and high active radioactive waste are designed to withstand severe accidents. Specific mechanical and thermal tests are defined in the IAEA Regulations for the Safe Transport of Radioactive Materials in order to cover these hypothetical severe accidents. The thermal test mainly consists of a 30 minute fully engulfing fire. Components such as the package impact limiters can lead to supplementary energy release during the thermal test as they might continue burning after the fire phase. Local heat flux into the package can occur. Measurement of heat flux into the package is of importance to evaluate component temperatures and review their acceptance. The usability of heat flux sensors and temperature measurement equipment has to be tested to apply them in impact limiter fire testing. Further questions arise such as :“Is the infrared camera a useful tool to determine heat flux at the boundary surface?” T2 - Technical Exchange IRSN – BAM Transport & Storage of Packages for Radioactive Material CY - Berlin, Germany DA - 08.09.2021 KW - Heat flux sensor PY - 2021 AN - OPUS4-55659 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Duffner, Eric A1 - Mair, Georg T1 - TAHYA Kick-Off Meeting N2 - Presenting BAM and the focus and role within the project. T2 - TAHYA Kick-Off Meeting CY - Hasselt, Belgium DA - 18.01.2018 KW - TAHYA Project PY - 2018 AN - OPUS4-43922 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberwein, Robert A1 - Eberwein, Robert A1 - Scarponi, G. E. A1 - Dal Pozzo, Alessandro A1 - Otremba, Frank T1 - Systems With Cryogenic Liquefied Gases In Fire-Incidents N2 - The volumetric energy density of a gas can be increased by liquefaction, which occurs when the gas is cooled below the saturation point. Liquefied gases of great importance to the energy transition are Liquefied Hydrogen (LH2) and Liquefied Natural Gas (LNG), which can be liquefied at temperatures below 160°C. Systems for storing these gases typically must be overpressure resistant and require thermal super insulations (TSI) to hold cryogenic conditions and minimize boil-off losses from evaporation. TSI with vacuum and MLI or perlites are suitable for many applications involving LNG and LH2. Such systems are typically double-walled structures where the inner wall is in contact with the cryogenic liquefied gas. MLI or perlites are located in the gap between the inner and the outer wall, that is kept under vacuum conditions. This combination of insulations strongly reduces the heat transfer between the environment and the cryogenic liquefied gas. From an economic point of view the systems are well sophisticated. However, knowledge of the behavior of this kind of systems in a typical event such as a fire is limited, but necessary to evaluate the safety of the increasing number of applications. The objective of the research is to determine how TSI behaves at different fire temperatures during fire exposure and afterwards. Special attention is paid to changes in the heat flux, the material properties and vacuum state over time. For this purpose, thermogravimetric analysis (TGA) studies have been carried out. In addition, a test rig was developed that allows testing of TSI at temperatures up to 1000°C under realistic integration conditions and subsequent analysis of the TSI samples. In the test rig the double-wall with vacuum and MLI or perlites inside is simulated. The fire conditions are simulated on one side of the double-wall by adjustable electrical heating elements. This process allows the implementation of repeatable heat flows of up to 100 kW/m². On the other side of the double-wall, cold or cryogenic conditions are simulated with a heat exchanger through which water or the vapor of liquid nitrogen (approx. -196°C) flows. The heat exchanger is also used to determine the heat flux through the double-wall. Thus, the test rig allows thermal loading and performance analysis of TSI samples at the same time. Compared to tests with real cryogenic systems, tests with this experimental setup have the advantage that, first, the instrumentation is easier to realize, and a higher repeatability is ensured. Second, the local heat flow can be determined over time, and the sample of a TSI can be taken non-destructively and thus analyzed. Third, the tests are less risky as well as time+ and material intensive, so that more tests and variants can be investigated with the same budget. Preliminary results obtained considering several types of MLI under vacuum show that all observed typs of MLI can be damaged under strong thermal loading. The damages observed were outgassing, melting, shrinkage, cracking, lump formation, and concomitant local loss of the MLI's function as a radiation shield. However, the study also shows that a damage does not always have an extreme effect on the insulating performance. T2 - IMECE2022 CY - Columbus, Ohio, USA DA - 30.10.2022 KW - LH2 KW - LNG KW - Safety KW - Insulation KW - Tank PY - 2022 AN - OPUS4-56445 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank A1 - Eberwein, Robert A1 - Hajhariri, Aliasghar A1 - Camplese, Davide A1 - Scarponi, Giordano Emrys A1 - Cozzani, Valerio T1 - Systems with Cryogenic Liquefied Gases in Fire Incidents N2 - Liquefied Hydrogen (LH2) or Liquefied Natural Gas (LNG) establish themselves as important energy carriers in the transport sector. Its storage requires tanks with Thermal Super Insulations (TSI) to keep the transported fluid cold. TSI has proven itself in various applications over a long time, but not in the land transport sector, where accidents involving collisions, fires, and their combination are to be expected. The focus of this study is to investigate the behavior of different types of TSI when exposed to a heat source that represents a fire. Therefore, a High- Temperature Thermal Vacuum Chamber (HTTVC) was used that allows the thermal loading of thermal insulation material in a vacuum and measuring the heat flow through the TSI in parallel. Within this study, 5 samples were tested regarding 3 different types of MLI, rock wool, and perlites. The thermal exposure caused different effects on the samples. In practice, this can be connected to the rapid release of flammable gases as well as a Boiling Liquid Expanding Vapour Explosion (BLEVE). These results are relevant for the evaluation of accident scenarios, the improvement of TSI, and the development of emergency measures. T2 - IMECE 2023 CY - New Orleans, Louisiana, USA DA - 29.10.2023 KW - LH2 KW - LNG KW - Fire PY - 2023 AN - OPUS4-58769 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberwein, Robert T1 - Systems for the storage of cryogenic liquefied gases N2 - Liquefied Hydrogen (LH2) or Liquefied Natural Gas (LNG) establish themselves as important energy carriers in the transport sector. Its storage requires tanks with Thermal Super Insulations (TSI) to keep the transported fluid cold. The presentation includes 2 main topics of the department. First TSI has proven itself in various applications over a long time, but not in the land transport sector, where accidents involving collisions, fires, and their combination are to be expected. To analyze fire scenarios a High-Temperature Thermal Vacuum Chamber (HTTVC) was developed that allows the thermal loading of thermal insulation material in a vacuum and measuring the heat flow through the TSI in parallel. Within this chamber, 5 samples were tested regarding 3 different types of MLI, rock wool, and perlites. In the presentation, the results are presented. Second, the studying of accident scenarios enables the improvement of thermal superinsulation and to find novel insulation concepts. This is necessary for LH2 large-scale storages, for which state-of-the-art solutions are not suitable. Within the presentation, a novel insulation concept will be presented. T2 - Specialist Meeting - Threats to HAZMAT Pressure Vessels and BLEVE CY - Berlin, Germany DA - 25.04.2023 KW - Crygenic KW - LH2 KW - LNG KW - Fire KW - MLI PY - 2023 AN - OPUS4-57414 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberwein, Robert T1 - Systeme mit tiefkalt verflüssigten Gasen in Brandereignissen N2 - Die volumetrische Energiedichte eines Gases kann durch Verflüssigung erhöht wer-den. Diese findet statt, wenn das Gas unter den Siedepunkt abgekühlt wird. Verflüs-sigte Gase mit großer Bedeutung für die Energiewende sind verflüssigter Wasser-stoff (LH2) und verflüssigtes Erdgas (LNG), dessen Verflüssigung Temperaturen von unter -160 °C bedarf. Systeme zur Speicherung dieser verflüssigten Gase müssen in der Regel für Überdrücke ausgelegt sein und benötigen thermische Superisolierun-gen (TSI), um die tiefkalten Bedingungen über längere Zeit halten zu können und Verluste durch Boil-Off gering zu halten. TSI mit Vakuum und MLI oder Perlit sind für viele Anwendungen mit LNG und LH2 geeignet. Bei solchen Systemen handelt es sich in der Regel um doppelwandige Strukturen, bei denen die Innenwand mit dem tiefkalten Fluid in Kontakt steht. Die Lücke, zwischen der Innen- und der Außen-wand befindet sich unter Vakuumbedingungen und enthält zudem MLI oder Perlite. Diese Kombination von Isolationsmethoden ermöglicht es auf kleinstem Raum sehr gute thermische Isolationswirkung zu erreichen. Aus wirtschaftlicher Sicht sind die Systeme gut durchdacht. Das Wissen über das Verhalten dieser Systeme bei einem typischen Ereignis wie einem Brand ist jedoch begrenzt. Dieses Wissen ist aber not-wendig, um die Sicherheit der wachsenden Zahl von Anwendungen auf dem Markt bewerten zu können. T2 - H2-Kolloquium des Kompetenzzentrum „H2Safety@BAM” CY - Online meeting DA - 04.07.2022 KW - Tiefkalt KW - Verflüssigt KW - Isolation KW - Auslegungsüberschreitend PY - 2022 AN - OPUS4-55178 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Duffner, Eric A1 - Kriegsmann, Andreas T1 - System validation and safety aspects N2 - Overview of the achievements, issues and next steps with in TAHYA Project for WP5 T2 - TAHYA meeting PSB#2 CY - Saarburg, Germany DA - 11.06.2019 KW - TAHYA Project PY - 2019 AN - OPUS4-49188 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schilling, O. A1 - Neumann, Martin A1 - Wolff, Dietmar A1 - Wille, Frank A1 - Darnstädt, A. T1 - System of Quality Assurance Measures in Manufacturing and Operation of Dual Purpose Casks for Spent Nuclear Fuel and High Level Waste in Germany N2 - German spent nuclear fuel and high level waste is stored in dry conditions in interim storage facilities until a final repository will be ready for operation in the future. Dual purpose casks are used for the packaging of the materials to ensure transportability at any time during long-term interim storage and fulfilling both requirements from interim storage as well as transport. Germany’s 2011 decision to phase out utilization of nuclear energy has led to a high demand for casks for decommissioning power plants as quickly as possible. Cask serial production will continue at a high level for the next few years. In the process, a system of quality assurance measures ensures that every cask reliably complies with design specification according the transport approval certificate and storage license. When the first casks were manufactured in Germany about 40 years ago, quality assurance was oriented towards pressure vessel and general nuclear manufacturing. The system was continuously adapted to the state of the art. In particular serial production, globalization of manufacturing and deep supplier chains had to be taken into account. The system of quality assurance measures applied today for cask manufacturing shall be presented here. The quality assurance measures can be categorized as system-related and design-related. With respect to transport regulations for example, they are independently approved and monitored by the competent authority BAM and its authorized inspection experts. The qualification of the applicant is reviewed first in the context of the design approval procedure and then periodically. The qualification of component and cask manufacturers is also checked at the start of manufacturing and then periodically. Before the start of manufacturing documents such as quality plans are pre-assessed. Manufacturing and inspection are then performed according to the pre-assessed documents. Cask manufacturing is completed by a final inspection before commissioning. Periodic inspections during operation ensure preservation of the properties specified in the approval certificate over package life time. The type and the time interval of periodic inspections depend on the use of the package. For transport after interim storage a system of specific tests and inspections is prescribed. T2 - 20th International Symposium on the Packaging and Transportation of Radioactive Materials (PATRAM 22) CY - Juan-les-Pins, France DA - 11.06.2023 KW - Radioactive material KW - Quality Assurance Measures KW - Dual Purpose Casks KW - Independent Surveillance PY - 2023 AN - OPUS4-57705 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Romero-Navarrete, José A. A1 - Otremba, Frank A1 - Lozano Guzmán, A. A. T1 - Study on the potential effect of sloshing cargoes on rail endurance N2 - Formulations have been assembled and (some) have been validated to simulate the potential damaging effect of a sloshing cargo on the railway material. Results suggest that: -Spatial determinism of the wheel forces due to sloshing, as a function of curve radius, distance between wheelsets and vehicle speed. -Sloshing forces can contribute in a significant way to railway material failure. Further analysis should be performed:-to validate these results (field observations)-to include a stress analysis of the potential effect of the yaw stiffness of the cars on the rail forces. T2 - The Fourth International Conference on Railway Technology CY - Sitges, Barcelona, Spain DA - 03.09.2018 KW - Sloshing cargoes KW - Rail endurance PY - 2018 AN - OPUS4-45905 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Romero-Navarrete, José A. ED - Otremba, Frank ED - Lozano Guzmán, A. A. T1 - Study on the potential effect of sloshing cargoes on rail endurance T2 - The Fourth International Conference on Railway Technology N2 - Current railway infrastructure design methodologies take into account the load Transfer derived from the lateral acceleration exerted on the vehicle while Tuning, recommending the highest grades for such infrastructure Segments. T2 - Railways 2018 CY - Sitges, Barcelona, Spain DA - 03.09.2018 KW - Potential effect KW - Sloshing cargoes KW - Rail endurance PY - 2018 UR - http://www.railwaysconference.com/ SP - 1 EP - 3 AN - OPUS4-45908 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Karapanagiotis, Christos A1 - Schukar, Marcus A1 - Breithaupt, Mathias A1 - Duffner, Eric A1 - Ulbricht, Alexander A1 - Prager, Jens A1 - Krebber, Katerina T1 - Structural health monitoring of hydrogen pressure vessels using distributed fiber optic sensing N2 - We report on distributed fiber optic sensing-based monitoring of hydrogen composite overwrapped pressure vessels (COPV) to simultaneously increase the operational lifespan and mitigate maintenance costs. Our approach represents, to the best of our knowledge, the first application of distributed fiber optic sensing for COPV Type IV monitoring, where the sensing fibers are attached to the surface, rather than integrated into the composite material. Specifically, we attach an optical fiber of 50 m to the pressure vessel's surface, covering both the cylindrical and dome sections. We note that our fiber optic sensing technique relies on swept wavelength interferometry providing strain information along the entire length of the optical fiber with high spatial resolution even at the millimeter scale. When the vessel is pressurized, the sensing optical fiber shows a linear strain response to pressure at every position along the fiber. After thousands of load cycles, the vessel finally fails with the optical fiber detecting and precisely localizing the damage in the vessel’s blind dome area. Furthermore, we discuss the potential of state-of-the-art signal processing methods and machine learning for advancing predictive maintenance. This could reduce the number of regular inspections, mitigate premature maintenance costs, and simultaneously increase the vessel’s remaining safe service life. We believe that the structural health monitoring of hydrogen pressure vessels with fiber optic sensors can enhance trust in hydrogen technology contributing to the energy transition in the future. T2 - 11th European Workshop on Structural Health Monitoring CY - Potsdam, Germany DA - 10.06.2024 KW - Hydrogen KW - Composites KW - Pressure vessels KW - Fiber optic sensors KW - Machine learning KW - Structural health monitoring PY - 2024 AN - OPUS4-60275 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hille, Falk A1 - Herrmann, Ralf A1 - Said, Samir A1 - Ziegler, Fred A1 - Baeßler, Matthias A1 - Wille, Frank A1 - Quercetti, Thomas A1 - Minack, Mathias A1 - Sterthaus, Jens T1 - Structural Health Monitoring am Großen Fallturm der BAM N2 - In diesem Beitrag wird die Structural Health Monitoring Kampagne am Großen Fallturm der BAM vorgestellt. T2 - Seminar "Zerstörungsfreie Prüfung" CY - Online meeting DA - 13.01.2022 KW - Belastungsversuch KW - Großer Fallturm Horstwalde KW - Schwingungsdynamik KW - Modalanalyse PY - 2022 AN - OPUS4-55478 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hille, Falk A1 - Herrmann, Ralf A1 - Ziegler, Fred A1 - Said, Samir A1 - Baeßler, Matthias A1 - Wille, Frank A1 - Quercetti, Thomas A1 - Minack, Mathias A1 - Sterthaus, Jens T1 - Structural Health Monitoring am Großen Fallturm der BAM N2 - Am Fallturm auf dem Testgelände Technische Sicherheit (TTS) der BAM wurden bei Inspektionen Vorspannungsverluste in den Bolzen der Stahlverbindungen festgestellt. Um ein Verständnis für die zugrundeliegenden Trag- und Schädigungsmechanismen zu erlangen und um den Zustand der vorgespannten Schraubverbindungen langzeitlich zu überwachen, wurde am Fallturm ein Structural Health Monitoring (SHM) System installiert. Für die Auslegung des Monitoringsystems sowie zur Unterstützung der Untersuchung des Schädigungsprozesses wurde ein numerisches Modell erstellt und in Bezug auf die gemessenen Antworten des Tragwerks kalibriert. Im Vortrag werden die experimentellen und numerischen Untersuchungen zur Systemidentifikation des Stahlrohrgitterturms als auch die Überwachungskampagne mit dem eingesetzten Monitoringsystem sowie die Messergebnisse und deren Bewertung vorgestellt. T2 - Seminar "Zerstörungsfreie Prüfung" am Lehrstuhl für Zerstörungsfreie Prüfung ,Technische Universität München CY - Online meeting DA - 13.01.2022 KW - Structural Health Monitoring KW - Schadensüberwachung KW - Schwingungsmonitoring PY - 2022 AN - OPUS4-56667 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heimann, Jan A1 - Yilmaz, Bengisu A1 - Charmi, Amir A1 - Duffner, Eric A1 - Schukar, Marcus A1 - Prager, Jens T1 - Structural Health Monitoring (SHM) for continuous monitoring of hydrogen pressure vessels N2 - While hydrogen is one of the most promising energy carriers, the safety of hydrogen storage technology remains one of the most important factors for technological and societal approval. While the engineering safety factors of the pressure vessels are kept high, the periodic inspection and the limited lifetime are making the application very costly considering manpower, time, money, and material waste. The development of an integrated structural health monitoring system can allow an easy transition from the current situation to cost-effective predictive maintenance. Hence, we propose to integrate three different SHM systems into hydrogen pressure vessels, namely guided wave ultrasonics, acoustic emission, and fibre optic sensing, to continuously monitor the condition and integrity. In this work, we evaluated the condition of a Type IV composite overwrapped pressure vessel using ultrasonic guided wave propagation. We mounted fifteen piezo-electric wafers on the composite cylinder by shaping three rings containing five sensors each. We acquired data from the sensor network following different boundary conditions with artificial damages on the selected locations. The data were evaluated with guided wave tomography techniques using ultrasonic features (amplitude, frequency, etc.) as well as artificial intelligence (AI). The results suggest that both traditional guided wave fusion techniques and AI-based characterization methods can detect artificial damages. In future work, it is planned to integrate acoustic emission and fibre optic sensing. Moreover, the measurement and the test results will be implemented into a digital twin to derive trends and make predictions on the damage propagation as well as the remaining useful lifetime. This work has received funding from German Ministry of Economic Affairs and Climate Actions within the QI-Digital initiative (www.qi-digital.de). T2 - SCHALL 23 CY - Wetzlar, Germany DA - 21.03.2023 KW - Structural Health Monitoring KW - Ultrasonic Guided Waves KW - Composite Overwrapped Pressure Vessel KW - Hydrogen PY - 2023 AN - OPUS4-58026 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zencker, Uwe T1 - Stress wave propagation with finite element mesh transitions N2 - A reliable finite element analysis presupposes a qualified model of the object to be analyzed. The finite element mesh density may significantly vary throughout a model. A transition between dissimilar meshes can be accomplished by a gradual change of element size or by an interface with constraint conditions. Some issues may arise from such mesh transitions. Generally, a finer mesh can transmit signals of higher frequency than a coarser mesh. Stress wave propagation through the model could be affected by the transition region or the artificially induced interface. Stress waves generated within the fine mesh could be partly encapsulated by the surrounding coarse mesh. Therefore poor mesh transitions could result in reflections or shape changes of stress waves. A thin rod is investigated to demonstrate the effects. This study supports the development of the ASME Guidance Document "Use of Explicit Finite Element Analysis for the Evaluation of Nuclear Transport and Storage Packages in Energy-Limited Impact Events". T2 - 19th International Symposium on the Packaging and Transportation of Radioactive Materials (PATRAM 2019) CY - New Orleans, LA, USA DA - 04.08.2019 KW - Stress Wave Propagation KW - Thin Rod KW - Finite Element Mesh Transition PY - 2019 AN - OPUS4-48916 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Barthélémy, H. A1 - Agnoletti, A. A1 - Bortot, P. A1 - Mair, Georg A1 - Zheng, J. T1 - Storage N2 - The whole conference focused on gaps in research concerning hydrogen and hydrogen safety. This presentation focus on storage aspects and shows the current gaps in research from the point of view of the authors. They have differences in background, from university via manufacturer and safety institute to hydrogen operating industry. The different purposes of storage are covered (onboard storage, stationary storage and transport of gases) as well as the different designs (steel to pure composite/plastic). T2 - "Research Priorities Workshop RPW 2018" (EC & US DOE) CY - Buxton, UK DA - 18.09.2018 KW - Strength degradation KW - Initial testing KW - Knowledge gaps PY - 2018 AN - OPUS4-46159 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlick-Hasper, Eva A1 - Goedecke, Thomas A1 - Ackermann, M. A1 - Senkel, U. T1 - Staubdichtheit von Säcken und FIBC für feste Gefahrgüter - Eine kritische Betrachtung der derzeitigen Regelsetzung und Transportpraxis N2 - In den internationalen Gefahrgutvorschriften ist vorgeschrieben, dass Säcke und flexible Großpackmittel (Flexible Intermediate Bulk Container – FIBC) staubdicht sein müssen. Eine quantitative Definition des Terminus Staubdichtheit, wie in anderen Technikgebieten üblich, ist jedoch nicht gegeben. Auch geeignete Prüfverfahren zum Nachweis der Staubdichtheit sind in den Vorschriften nicht genannt. In der Praxis der stichpunkartigen Kontrollen von Gefahrguttransporten durch die Schwerlastgruppe der Autobahnpolizei Münster werden immer wieder Austritte von pulverförmigen oder körnigen Gefahrgütern aus eigentlich intakten Säcken und FIBC detektiert. Es wird ein Überblick über die im Jahr 2018 festgestellten Gefahrgutaustritte aus diesen Gefahrgutverpackungen sowie eine systematische Einordnung hinsichtlich betroffener Bauarten und möglicher Ursachen gegeben. Bei der Stofffreisetzung aus intakten Gefahrgutverpackungen liegt ein mechanischer Transport von Partikeln durch Leckkanäle, z. B. im Verschluss-, Naht- oder Wandungsbereich, vor. Generell kommen zwei Freisetzungswege in Frage: Einerseits eine Langzeit-Freisetzung während des Transports, hervorgerufen durch eine kombinierte Wirkung von Stapellast des Füllguts und Transportvibrationen; andererseits eine stoßartige Freisetzung. Auf Grundlage von durchgeführten Untersuchungen hinsichtlich der stoßartigen Freisetzung pulverförmiger Stoffe aus Gefahrgutsäcken werden erste Lösungsansätze hin zu einer Verbesserung der Staubdichtheit von Gefahrgutsäcken und -FIBC vorgestellt. Es wird ein Ausblick auf nachfolgende Arbeiten gegeben. T2 - 48. Jahrestagung der GUS 2019 CY - Stutensee, Ortsteil Blankenloch, Germany DA - 27.03.2019 KW - Gefahrgutverpackungen KW - Staubdichtheit KW - Säcke KW - FIBC PY - 2019 AN - OPUS4-47692 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völzke, Holger T1 - Stand bei den Behälterbauartprüfungen für das Endlager Konrad N2 - Die Verfügbarkeit von Behältern für die Entsorgung nicht Wärme entwickelnder radioaktiver Abfälle im Endlager Konrad stellt ein wesentliches Element des nationalen Entsorgungskonzeptes für diese Abfallart dar. Grundlage für die Verfügbarkeit geeigneter Behälter sind typspezifische Bauartprüfungen, auf deren Grundlage eine Eignungs-feststellung in Form eines Prüfzeugnisses durch die Bundesgesellschaft für Endlagerung mbH (BGE), vormals Bundesamt für Strahlenschutz (BfS), erfolgt. Die Prüfgrundlagen sind in den durch das BfS (heute BGE) veröffent-lichten „Anforderungen an endzulagernde radioaktive Abfälle“ (Endlagerungsbedingungen) sowie der zugehörigen „Produktkontrolle radioaktiver Abfälle, radiologische Aspekte“ (PK) verankert. Die Eignungsfeststellung für eine Behälterbauart ist gleichzeitig die Grundlage für eine Behälterserienfertigung entsprechend den im Prüfzeugnis verankerten Spezifikationen und Randbedingungen. Mit den Gesetzen zur Neuordnung der Organisationsstruktur im Bereich der Endlagerung (Mitte 2016) und zur Neuordnung der Verantwortung in der kerntechnischen Entsorgung (Mitte 2017) mit der Finanzierung des Kern-energieausstiegs wurden wesentliche Weichenstellungen im Hinblick auf den anstehenden Rückbau der bereits stillgelegten und in den kommenden Jahren noch stillzulegenden deutschen Kernkraftwerke vorgenommen. Bezüg-lich der nicht Wärme entwickelnden radioaktiven Abfälle führt dies zu einer spürbaren Intensivierung der Anstren-gungen zur Bereitstellung qualifizierter Gebinde für das Endlager Konrad, das nach aktueller Planung bis 2027 sei-nen Einlagerungsbetrieb aufnehmen soll. Dies wiederum führt zu einer erheblichen Verdichtung der Verfahren zur Behälterbauartprüfung, die allen Seiten (Antragsteller, BGE, Gutachter) erhebliche Anstrengungen abfordert. Die Bundesanstalt für Materialprüfung und –forschung (BAM) ist auf Grundlage des Kap. 7 der o. g. „Produktkon-trolle …“ (PK) von der BGE mit den Behälterbauartprüfungen für das Endlager Konrad beauftragt. Hierbei ist eine Vielzahl von Anforderungen zu berücksichtigen, wozu neben den Anforderungen an Abfallbehälter gemäß Kap. 5 der Endlagerungsbedingungen weitere Anforderungen an die Verpackung (Kap. 3.2.2 PK), Kenngrößen (Kap. 3.5.1 PK) und schließlich die eigentliche Prüfung von Behältern/Verpackungen zählt (Kap. 7 PK). Letzteres beinhaltet die umfassende Behälterbeschreibung und –spezifikation, die Behälterauslegung, die thermischen und mechanischen Baumusterprüfungen (z.B. Brand- und Fallprüfungen), und schließlich die qualitätssichernden Maßnahmen für Her-stellung und Betrieb der Behälter. Neben der klassischen Bauartprüfung neuer Behältertypen spielt auch die Prü-fung bereits hergestellter Behälter, sog. Altbehälter, eine wesentliche Rolle, da sich etliche tausend Gebinde be-reits in der Zwischenlagerung befinden und nach Möglichkeit für das Endlager Konrad qualifiziert werden sollen. Dieser Beitrag berichtet aktuell über den Umfang und Stand der laufenden Bauartprüfungen bei der BAM unter Be-rücksichtigung der besonderen Herausforderungen und der zuletzt erzielten Fortschritte. Dabei erfordert die paral-lele Bearbeitung der zahlreichen Verfahren einen verstärkten Koordinierungsbedarf hinsichtlich vergleichbarer fach-licher Aspekte sowie hinsichtlich Priorisierung und Ressourceneinsatz. Bei den experimentellen Nachweisen (Fall- und Brandversuche) betrifft das hinsichtlich der Nutzung der Versuchseinrichtungen bei der BAM die Koordination mit anderen Prüfaufträgen, wie z. B. verkehrsrechtliche Baumusterprüfungen. Schließlich erfordern diverse Fach-fragen zur Interpretation der Anforderungen aus Endlagerungsbedingungen und Produktkontrolle intensive Abstim-mungsprozesse zwischen BAM, BGE und Antragstellern. Wichtige Ergebnisse mit übergeordneter Bedeutung wer-den in Form erläuternder Fachnotizen durch die BGE veröffentlicht und können so bei zukünftigen Antragsverfahren berücksichtigt werden. T2 - KONTEC 2019 CY - Dresden, Germany DA - 27.03.2019 KW - Endlager KW - Container KW - Bauartprüfung KW - Konrad PY - 2019 AN - OPUS4-47668 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zencker, Uwe T1 - Spent Fuel Characterization - Current Activities in Germany N2 - The characterization of spent fuel and radioactive waste is essential in the evaluation of the ability of these materials to meet acceptance criteria. Prior to determining a method for spent fuel characterization, it is necessary to identify the type of data required to support safety and other analyses for the storage, transportation and final disposal of spent fuel. BAM’s understanding and capabilities in the field of spent fuel characterization are presented for the scope of a coordinated research project on the topic. T2 - IAEA Technical Meeting on Spent Fuel Characterization for Management of Spent Fuel in the Back End of the Fuel Cycle CY - Vienna, Austria DA - 12.11.2019 KW - Nuclear fuel cycle KW - Back end KW - Spent fuel characterization KW - Storage KW - Transportation PY - 2019 AN - OPUS4-55866 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zencker, Uwe T1 - Spent Fuel Characterization - Current Activities at BAM N2 - The European Joint Programme on Radioactive Waste Management (EURAD) is working on Spent Fuel Characterization (SFC) in its work package (WP) 8. Inspired by the EURAD activities, the International Atomic Energy Agency (IAEA) established an international Coordinated Research Project (CRP) on SFC. The EURAD WP SFC participants are collaborating as a team on the IAEA CRP on SFC. The EURAD WP SFC project consists of four tasks. Task 3 investigates the behaviour of nuclear fuel and cladding after discharge. The aim of these activities is to understand and describe the evolution of the cladding-pellet system and its ageing under conditions of extended interim storage, transportation and emplacement in a final disposal system. At a Consultancy Meeting, BAM as contributor to Task 3 presented current results of the failure analysis of irradiated ZIRLO® claddings under conditions of the Ring Compression Test. T2 - IAEA Consultancy Meeting on the Coordinated Research Project on Spent Fuel Characterization CY - Online meeting DA - 12.09.2023 KW - Nuclear Fuel Cladding KW - Numerical Failure Analysis KW - Ring Compression Test KW - Spent Fuel Characterization KW - Extended Interim Storage PY - 2023 AN - OPUS4-58276 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wille, Frank A1 - Linnemann, Konrad A1 - Ballheimer, Viktor A1 - Rolle, Annette T1 - Spent fuel behavior under Transport Conditions N2 - German packages for the transport of spent nuclear fuel are assessed with respect to specific transport conditions which are defined in the safety regulations of the International Atomic Energy Agency. In general, gastight fuel rods constitute the first barrier of the containment system. The physical state of the spent fuel and the fuel rod cladding as well as the geometric configuration of the fuel assemblies are important inputs for the evaluation of the package safety under transport conditions. The objective of this paper is to discuss the methodologies accepted by German authority BAM for the evaluation of spent fuel behavior within the package design approval procedure. Specific test conditions will be analyzed with regard to assumptions to be used in the activity release and criticality safety analysis. In particular the different failure modes of the fuel rods, which can cause release of gas, volatiles, fuel particles or fragments, have to be properly considered in these assumptions. The package as a mechanical system is characterized by a complex set of interactions, e.g. between the fuel rods within the assembly as well as between the fuel assemblies, the basket, and the cask containment. This complexity together with the limited knowledge about the material properties and the variation of the fuel assemblies regarding cladding material, burn-up and the operation history makes an exact mechanical analysis of the fuel rods nearly impossible. The application of sophisticated numerical models requires extensive experimental data for model verification, which are in general not available. The gaps in information concerning the material properties of cladding and pellets, especially for the high burn-up fuel, make the analysis more complicated additionally, and require a conservative approach. In this context some practical approaches based on experiences by BAM within safety assessment of packages for transport of spent fuel will be discussed. Ongoing research activities to investigate SNF mechanical behavior in view of gas and fissile material release under transport loads are presented. T2 - IRSN Conference on Safe Transport of Radioactive Material CY - Fontenay aux Roses, France DA - 13.11.2018 KW - ENSA KW - SNL KW - Real transport KW - IAEA KW - Drop test KW - Multi-Modal Transportation Test KW - Radioactive KW - ACT KW - NCT KW - Hot cell KW - Activity release KW - Fuel rod KW - Fuel rods KW - Burn-up KW - Cladding alloy KW - Criticality safety analysis KW - Containment analysis KW - Fuel assemblies KW - Spent fuel PY - 2018 AN - OPUS4-46880 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rolle, Annette A1 - Komann, Steffen A1 - Wille, Frank T1 - Special form radioactive material (SFRM)- kick off discussion for harmonisation of approval procedure and certificate N2 - Exchange of experiences in SFRM approval procedure, Possibilities for harmonisation. Support for preparation of proposal for the next IAEA SSR-6/ SSG-26 revision process concerning. Special Form Radioactive Material (SFRM)-working life. T2 - European Association of Competent Authorities for safe Transport of Radioactive Material, Meeting 15 CY - Athen, Greece DA - 15.05. 2019 KW - Ageing behaviour KW - Radioactive sources KW - Approval PY - 2019 AN - OPUS4-48061 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank A1 - Romero-Navarrete, José A. T1 - Sloshing in vertical circular Tanks and Earthquakes Perturbations N2 - Tanks with capacity larger than 700 m3, could be exposed to a resonance excitation when subjected to earthquake motions, regardless of the fill level. Further studies to assess the dynamic forces linked to such resonance and close-to-resonance situations, in a context of a standard overloading situation due to sloshing forces. T2 - WCECS 2019 CY - San Francisco, CA, USA DA - 22.10.2019 KW - Sloshing KW - Tanks KW - Earthquake KW - Perturbation PY - 2019 AN - OPUS4-49408 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krug von Nidda, Jonas T1 - Single Cell Exchange in Battery Packs – Sustainability vs. Safety Aspects N2 - Lithium-ion batteries usually consist of numerous individual cells. There is ongoing discussion about enhancing sustainability by considering the replacement of heavily aged or damaged cells. Nevertheless, the planned replacement of individual cells poses significant challenges in ensuring the required reliability and safety of the refurbished device. T2 - KLIB Gesprächsrunde Batteriesysteme CY - Online meeting DA - 16.05.2023 KW - Lithium Ion Batteries KW - Lithium Ion Cells KW - Cell Exchange KW - Safety KW - Sustainability PY - 2023 AN - OPUS4-59272 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Romero-Navarrete, José A. A1 - Otremba, Frank A1 - Lozano Guzmàn, A. A. T1 - Simulation of liquid cargo - vehicle intearction under lateral and longitudinal accelerations N2 - A nonlinear relationship between the magnitude of the radius and the maximum value reached for the selected performance measure. The dispersion in the travelling speed also represents significant variations in the vehicle performance, when it runs along a winding road. T2 - The 9th International Conference on Computational Methods (ICCM2018) CY - Rom, Italy DA - 06.08.2018 KW - Simulation KW - Liquid cargo KW - Vehicle KW - Acceleration PY - 2018 AN - OPUS4-45705 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sklorz, Christian A1 - Otremba, Frank T1 - Simulation eines Poolfeuers im 1m³ Ofen N2 - Zur Charakterisierung von Brandschutzbeschichtungssystemen für Gas- Lagertanks ist ein Großbrandversuch erforderlich. Zur Ermittlung der produktspezifischen Beschichtungsdicke sind Plattenbrandversuche notwendig. Für Brandprüfungen existieren verschiedene Brandkurven (z.B. ETK, Hydrocarbonkurve, Schwelbrandkurve, BAM-Kurve) um Prüfmuster je nach Anwendungsfall zu zertifizieren. Diese Brandkurven unterscheiden sich hinsichtlich des Temperaturgradienten. Zur Gewährleistung der Übertragbarkeit der BAM-Prüföfen (Kleinprüfstand DIN 4102-8 (Klep) und 1-m³ Ofen) auf die NORM ISO 21843 (2018-09) ist es erforderlich einen Wärmeintrag von 90 – 120 kW/m² in das Prüfmuster zu garantieren. T2 - TF-IF CY - Berlin, Germany DA - 16.09.2019 KW - Brandversuch KW - Fire testing KW - Ofen PY - 2019 AN - OPUS4-49250 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg T1 - Sicherheitsforschung im Bereich Wasserstoff – Transport von CGH2 N2 - Ein Aspekt des Gefahrguttransportes, der an Bedeutung in den letzten Jahren zugenommen hat, ist die Versorgung von Wasserstofftankstellen und anderen H2-Großverbrauchern über die Schiene aber insbesondere über die Straße. Mit Blick auf die primäre Form der Speicherung wird der Begriff der Sicherheit über den Aspekt der Häufigkeit eines definierten Ereignisses erläutert und auf die Besonderheiten der Druckgefäße aus Verbundwerkstoffen hingewiesen, wie auch den regulatorischen Hintergrund der Lebensdauerüberprüfung nach 15 Jahren nach den Vorgaben der zuständigen Behörde. In Deutschland sind diese Vorgaben in der BAM-Gefahrgutregel 021 geregelt, die in der GGR 022 durch eine Regelung zur Wiederkehrenden Prüfung dieser Umschließungen ergänzt wird. Beide BAM-Gefahrgutregeln basieren auf einem probabilistischen Ansatz und einer Konsequenzabschätzung über das Druck-Volumen-Produkt der Druckgefäße. Die neu im Recht verankerte EN 17339 ist die erste Norm, die speziell fest montierte Compositespeicher für den Wasserstofftransport regelt. Sie ermöglicht eine erhebliche Gewichtreduktion und führt eine Obergrenze für das Druckvolumen ein. Es wird kurz erläutert, dass gerade mit Blick auf Wasserstofftransporte über eine Arbeitsgruppe der Vereinten Nationen eine Begrenzung des Konsequenzpotentials in das internationale Recht eingeführt werden soll und welche Kriterien bei der systematischen Ermittlung des akzeptierten Wertes von 1.5 Mio bar Liter Einfluss haben. Mit Blick auf die Energiewende sieht es die BAM als besonders wichtig an, die Transportkosten zu senken, indem der Prüfaufwand reduziert und gleichzeitig die Erkenntnistiefe aus der betrieblichen Überwachung verbessert wird. Hierzu muss die Datenbasis für die probabilistische Bewertung der Lebensdauer von zerstörenden Prüfungen auf zerstörungsfreie Prüfungen umgestellt werden und idealerweise die 100% Prüfung zumindest in der ersten Hälfte des sicheren Lebens auf Stichproben reduziert werden. Dies und andere Aufgaben, die wichtig für eine sichere und attraktive Wasserstoffwirtschaft sind werden von dem Kompetenzzentrum H2Safety@BAM bearbeitet, dass in seinen Grundzügen kurz vorgestellt wird. T2 - IAA Transportation 2022 CY - Hannover,Germany DA - 20.09.2022 KW - H2Safety@BAM KW - Markthochlauf KW - Lebensdauervorhersage KW - zerstörungsfreie Prüfung ZfP KW - Risikosteuerung PY - 2022 AN - OPUS4-56984 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wolf, Michael T1 - Sicherer Transport von Lithium- und Lithium-Ionen-Batterien N2 - Sicherer Transport von Lithium- und Lithium-Ionen-Batterien. Wie ist der Vorschriftenstand ADR 2019. Unter welchen Bedingungen können Lithiumbatterien transportiert werden. T2 - 12. Thüringer Gefahrgutforum CY - Gera, Germany DA - 11.06.2019 KW - Lithiumbatterien KW - Transport KW - ADR 2019 PY - 2019 AN - OPUS4-48216 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tiebe, Carlo A1 - Maiwald, Michael A1 - Bresch, Sophie A1 - Prager, Jens A1 - Lugovtsova, Yevgeniya A1 - Schukar, Marcus A1 - Munzke, Dorit A1 - Duffner, Eric A1 - Eisermann, René A1 - Schoppa, André A1 - Szczepaniak, Mariusz A1 - Strohhäcker, J. A1 - Mair, Georg T1 - Sensoren und Analytik für Sicherheit und Prozesskontrolle in Wasserstofftechnologien N2 - Der Beitrag beinhaltet Themen vom H2Safety@BAM-Kompetenzfeld Sensorik, Analytik und zertifizierte Referenzmaterialien (SensRef) mit Fokus auf Mess- und Prüfverfahren mit verschiedenen Sensortechnologien und Ultraschallwellen: Metrologie zur Wasserstoffspeicherung - Euramet-Vorhaben "MefHySto", Erkennung von freigesetztem Wasserstoff sowie die Bestimmung des Wasserstoff-Luftverhälntisses mit Gassensoren, zerstörungsfreie Fehlstellenerkennung mit integriertem Zustandsüberwachungssystem basierend auf geführten Ultraschallwellen zur Lebensdauerüberwachung von Composite-Behältern (Wasserstoffspeicher) sowie faseroptische Sensorik zur Schadenfrüherkennung von Wasserstoffspeichern aufgrund erkennbarer Dehnungsänderungen an Druckbehältern. T2 - DVGW Kongress H2 Sicherheit CY - Online meeting DA - 23.11.2022 KW - H2Safety@BAM KW - SensRef KW - Faseroptische Sensorik KW - Gassensorik KW - Geführte Ultraschallwellen KW - Leckdetektion KW - Metrologie zur Wasserstoffspeicherung KW - Zerstörungsfreie Prüfung KW - Structural Health Monitoring (SHM) PY - 2022 AN - OPUS4-56683 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Anita T1 - Second life für E-Akkus N2 - Um die Nachhaltigkeit von Lithiumbatterien zu gewährleisten, kommt neben dem Recycling der Rohstoffe auch eine Weiternutzung von für die Erstanwendung nicht mehr ausreichend leistungsstarken Batterien aus der Erstanwendung in Frage. Dabei sind auch Sicherheitsaspekte zu beachten. T2 - Berlin Science Week 2021 CY - Online meeting DA - 10.11.21 KW - Lithium Batterien KW - Recycling KW - Second Life KW - State of Safety PY - 2021 AN - OPUS4-54178 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Widjaja, Martinus Putra T1 - Sample Performance Chart (SPC) for displaying the results from a multiscale model N2 - The stacking sequence of a real scale type IV pressure vessels has been found. Feasibility study of a multiscale model has been carried out by modifying the original stacking sequence. All of the results were displayed in a Sample Performance Chart (SPC), where different burst pressure in terms of mean and scatter had been found. T2 - Consortium Meeting FiBreMoD CY - Valence, France DA - 17.02.2020 KW - Fibre break KW - Multiscale model KW - Reduced volume method KW - Sample performance chart KW - Type IV pressure vessels PY - 2020 AN - OPUS4-50563 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg T1 - Salvage pressure receptacles - Technical background N2 - The presentation reflects the questions that have been raised by member states and NGOs. As background information details on the question how to choose a suitable salvage pressure receptacle (SPR) are provided. This leads to the need for deleting the volume limitation for SPRs and to the discussions in 2014 and 2016 on this issue. As an adequate substitution for deleting the volume limit for SPRs it is proposed to limit the pressure receptacles to be stored in by a maximum pressure-volume-value of 1.5 Mio bar-litres. After some explanations to standardisation projects currently also tackling this pV-limit, some risk-based safety criteria for a limitation are mentioned with the focus of the consequence level and the general avoidance of catastrophic worst case scenarios. T2 - 57th session of TDG Sub-Committee CY - Online meeting DA - 30.11.2020 KW - Salvage pressure receptacle KW - Consequence KW - Catastrophe KW - Compressed gas PY - 2020 AN - OPUS4-53161 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Anita T1 - Safety in transport of Li-ion batteries N2 - Safety in transport is the pre-requisite for bringing Lithium-ion batteries on the market. In order to consider the different types and degree of hazards, UN has set out to define a new classification system based on testing. BAM has participated in the test rounds and presents here the results. T2 - Technical Workshop on Advanced Materials Challenges and Standardisation Needs for Net Zero Technologies (AMCSNZT-2023) CY - New Delhi, India DA - 09.10.2023 KW - Lithium-ion batteries KW - Propagation testing KW - Safety PY - 2023 AN - OPUS4-59274 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg A1 - Saul, Herbert A1 - Wang, Bin T1 - Safety criteria for the transport of hydrogen in permanently mounted composite pressure vessels N2 - The recent growing of the net of hydrogen fuelling stations increases the demands to transport compressed hydrogen on road by tube-trailers in composite pressure vessels. As transport regulation the ADR is applicable in Europe and adjoined regions and used for national transport in EU. This regulation provides requirements based on the burst pressure of each individual pressure vessel, regardless the capabilities of the transported hydrogen and relevant consequences resulting from worst case scenarios. In 2012, BAM (German Federal Institute for Materials Research and Testing) introduced consequence-dependent requirements and established them in national requirements concerning the “UN service life checks” etc.) to consider the transported volume and pressure of gases. However, this results in a stringent requirement in case of using large pressure vessels (tubes) on tube-trailers. In the studies presented here, the key safety factors for using hydrogen trailers are identified and reviewed through some safety measures from some countries like Japan, USA and China. Subsequently, the risk, chance, failure consequences of using trailers are evaluated, in addition, the difficulties for approving huge pressure vessels (large tubes) are addressed. There, a maximum acceptable pressure-volume product is defined. Finally, a performance-based criterion for the balance of chance and risk of hydrogen trailers is suggested to add into regulations and consequently into standards for hydrogen trailers. T2 - ICHS (International Conference on Hydrogen Safety) 2019 CY - Adelaide, Australia DA - 24.09.2019 KW - Battery vehicle KW - Pressure-volume product KW - Maximum acceptable consequence KW - Catastrophe KW - F-N-curve KW - Pressure wave PY - 2019 AN - OPUS4-50088 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg A1 - Duffner, Eric A1 - Wang, Bin T1 - Safety Assessment of RCS by BAM N2 - The presentation explains the intended way of BAM in tackling the safety issues in the project TAHYA. The way how the term “safety” is used in TAHYA leads to the need for a more risk-based understanding of safety. Based on this, the Monte Carlo simulation is used to show where the weak points of current regulations are. Thus, a concept for optimization of relevant regulations, codes and standards will be elaborated during the project. For this purpose, it is helpful to improve the currently operated tool for Monte Carlo simulation, which will need additional data for monitoring the outcome. Strength data, that will be determined by BAM and the other partners during the already agreed test program can be used for this purpose without additional effort. T2 - Consortial Meeting TAHYA CY - Regus at Diegem, Brussels DA - 31.05.2018 KW - Risk KW - Acceptance rate KW - Survival rate KW - Composite KW - Hydrogen Storage PY - 2018 AN - OPUS4-45479 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Günzel, Stephan A1 - Mair, Georg T1 - Safety assessment of hydrogen gas storage systems N2 - In this lecture, the safety assessment of hydrogen gas storage systems is presented using the example of composite pressure vessels. The main element is a probabilistic approval approach based on five steps. Firstly, the testing and evaluation of properties at the beginning of life are shown. Secondly, methods for artificial aging and the effect on the residual strength are presented. Thirdly, testing against dedicated accidents is introduced. Fourthly, effects on the surveillance of production quality are discussed. Finally, degradation and the end of life are estimated. Background information and examples are given for each step. The assessment presented is a method applicable for many safety-related systems. T2 - Joint European Summer School 2021 on Fuel Cell, Electrolyser, and Battery Technologies CY - Online meeting DA - 12.09.2021 KW - Safety KW - Hydrogen KW - Wasserstoff KW - Bewertung KW - Assessment PY - 2021 AN - OPUS4-59905 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Günzel, Stephan A1 - Mair, Georg T1 - Safety assessment of hydrogen gas storage systems N2 - In this lecture, the safety assessment of hydrogen gas storage systems is presented using the example of composite pressure vessels. The main element is a probabilistic approval approach based on five steps. Firstly, the testing and evaluation of properties at the beginning of life are shown. Secondly, methods for artificial aging and the effect on the residual strength are presented. Thirdly, testing against dedicated accidents is introduced. Fourthly, effects on the surveillance of production quality are discussed. Finally, degradation and the end of life are estimated. Background information and examples are given for each step. The assessment presented is a method applicable for many safety-related systems. T2 - Joint European Summer School 2023, Hydrogen Safety CY - Online meeting DA - 17.09.2023 KW - Safety KW - Hydrogen KW - Wasserstoff KW - Bewertung KW - Assessment PY - 2023 AN - OPUS4-59903 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Günzel, Stephan A1 - Mair, Georg T1 - Safety assessment of hydrogen gas storage systems N2 - In this lecture, the safety assessment of hydrogen gas storage systems is presented using the example of composite pressure vessels. The main element is a probabilistic approval approach based on five steps. Firstly, the testing and evaluation of properties at the beginning of life are shown. Secondly, methods for artificial aging and the effect on the residual strength are presented. Thirdly, testing against dedicated accidents is introduced. Fourthly, effects on the surveillance of production quality are discussed. Finally, degradation and the end of life are estimated. Background information and examples are given for each step. The assessment presented is a method applicable for many safety-related systems. T2 - Joint European Summer School 2022, Hydrogen Safety CY - Athens, Greece DA - 18.09.2022 KW - Safety KW - Hydrogen KW - Wasserstoff KW - Bewertung KW - Assessment PY - 2022 AN - OPUS4-59904 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Günzel, Stephan A1 - Mair, Georg T1 - Safety assessment of hydrogen gas storage systems N2 - In this lecture, the safety assessment of hydrogen gas storage systems is presented using the example of composite pressure vessels. The main element is a probabilistic approval approach based on five steps. Firstly, the testing and evaluation of properties at the beginning of life are shown. Secondly, methods for artificial aging and the effect on the residual strength are presented. Thirdly, testing against dedicated accidents is introduced. Fourthly, effects on the surveillance of production quality are discussed. Finally, degradation and the end of life are estimated. Background information and examples are given for each step. The assessment presented is a method applicable for many safety-related systems. T2 - Masterstudiengang Wasserstofftechnologie - Modul 8: Safety and Public Acceptance – Sicherheitsaspekte, Akzeptanz und werkstofftechnische Herausforderungen des Wasserstoffs CY - Online meeting DA - 25.08.2023 KW - Safety KW - Hydrogen KW - Wasserstoff KW - Bewertung KW - Assessment PY - 2023 AN - OPUS4-59899 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rolle, Annette A1 - Neumeyer, Tino A1 - Wille, Frank T1 - Safety assessment of aged metal seals N2 - With our experiments we want to simulate a load situation which can result from a cask vertical drop test. The lid can lift a little for a very short moment and that can perhaps result in a little movement of the seal, a little rotation or a little lateral movement, so that the contact section can change. The aim of the project is to learn more about the sealing efficiency after the seal is compressed again. What we know from former component tests with non-aged seals is, that the leakage rate measured after one or more decompression /compression cycles with seal movement becomes significant higher. And this result is considered for specification of design leakage rates for release calculation in safety cases. In the recent years we all have learned more about the significant influence of temperature and time on seal behavior and so the plan was to do similar experiments with aged seals, just to get an idea about seal behavior and achievable leakage rates. What we did in detail is: We compressed Helicoflex-seals of both design types, with Aluminum and Silver outer jackets, in testflanges and aged them in an oven at a temperature of 125°C for 3 months to produce seal properties comparable with properties after several years use at more typical operating temperatures between 90 and 100°C. After this ageing procedure we opened the flanges completely, moved the seal a little to vary the contact area and compressed the flanges again. What we measured during all compression and decompression cycles was the load, the deformation and -as long as possible- the leakage rates. T2 - Workshop IRSN/BAM CY - Cadarache, France DA - 12.10.2022 KW - Transport KW - Radioactive KW - Seal behavior KW - Ageing PY - 2022 AN - OPUS4-56141 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Günzel, Stephan A1 - Mair, Georg A1 - Wang, Bin T1 - Safety aspects of hydrogen transportation N2 - In this presentation safety aspects of hydrogen transportation are discussed. At first, the regulatory background and level of safety are presented. In the second part, the modelling of consequence due to sudden rupture of pressure receptacles is explained. Finally, the results are used to define a limit for consequence to enable an acceptable and safe transport of hydrogen. T2 - 3rd Germany-Korea Hydrogen Conference CY - Berlin, Germany DA - 27.09.2022 KW - Safety KW - Hydrogen KW - Wasserstoff KW - Gefahrgut KW - Consequence PY - 2022 AN - OPUS4-59902 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Holtappels, Kai A1 - Mair, Georg A1 - Kluge, Martin A1 - Habib, Abdel Karim T1 - Safety Aspects for Hydrogen Technologies - H2Safety@BAM N2 - Hydrogen is a central component of the energy transition and the European Green Deal for a climate-neutral Europe. To be able to achieve the targets defined by 2045, the EU and the German government have drafted a framework for action and are making long-term investments in research, development and the rapid implementation of innovative hydrogen technologies. The conditions for a successful energy transition and the economic use of green hydrogen as a clean energy carrier are Hydrogen readiness and a rapid market ramp-up, as well as the establishment of the necessary value chains in the national and European framework. Reliable quality and safety standards are the prerequisite for ensuring safety of supply and environmental compatibility and for creating trust in these technologies. BAM has bundled its expertise in the field of hydrogen technologies into a competence center H2Safety@BAM to create confidence in the technology and to support the hydrogen strategies of the German government and the EU. The topic of hydrogen has been current at BAM for more than one hundred years and is also currently the focus of numerous research and cooperation activities. The competence centre H2Safety@BAM and its vision of “We build trust in hydrogen technologies” will be presented with its many safety-related topics, which can be found throughout the entire hydrogen value chain. Two deep dives will present the results on projects dealing with the design-to-cost issue of classical pressurized gas storage containments and the consequences of the release of liquid hydrogen, which will be roughly compared to the release of ammonia. T2 - 25. Kalorimetrietage CY - Braunschweig, Germany DA - 31.05.2023 KW - H2Safety@BAM KW - Safety KW - Hydrogen KW - Gas cylinders KW - DELFIN KW - LH2 KW - Hydrogen release KW - Rapid phase transition KW - Consequences KW - Cyro storage tanks PY - 2023 AN - OPUS4-57629 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Anita T1 - Role of the Authority in the Approval Process of Packaging N2 - In Germany, BAM is the competent authority in the field of dangerous goods transport. The international dangerous goods transportation rules are presented and their adaptation into German law is described. BAM is responsible for dangerous goods packaging testing, manufacturer surveillance, packaging approvals and inspection of IBC and provides “Gefahrgutregeln” (GGR) to define the processes, e.g. of dangerous goods packagings approvals and surveillance.” T2 - Sino-German Workshop on Dangerous Goods Packaging CY - Online meeting DA - 18.11.2022 KW - Gefahrgutverpackungen KW - Zulassung KW - ADR PY - 2022 AN - OPUS4-56754 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühl, Christiane T1 - Risikomanagement beim Transport gefährlicher Güter in Europa T2 - 29. Münchner Gefahrgut-Tage N2 - Auf Initiative der Europäischen Kommission ist die Europäische Eisenbahn Agentur seit einigen Jahren damit beauftragt, in Zusammenarbeit mit einer Reihe von Expertinnen und Experten aus Europa harmonisierte Leitlinien für das Risikomanagement im Gefahrgutsektor zu entwickeln und fortzuschreiben. Der Vortrag informiert über die Entwicklung und den Stand der Arbeiten zum „Inland Transport of Dangerous Goods Risk Management Framework“ (RMF): - Warum gibt es das Risk Management Framework? - Wer ist an der Entwicklung beteiligt? - Wie ist das Risk Management Framework aufgebaut, an wen richtet es sich und was beinhaltet es? - Welche grundsätzlichen Fragen sind zu klären? - Wie geht es weiter? T2 - 29. Münchner Gefahrgut-Tage CY - Munich, Germany DA - 27.05.2019 KW - Gefahrguttransport KW - Risikomanagement KW - Risk Management Framework PY - 2019 SP - Paper 14, 1 PB - Süddeutscher Verlag Veranstaltungen GmbH CY - Landsberg AN - OPUS4-48738 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wille, Frank A1 - Moutarde, M. A1 - Apel, Andreas A1 - Nehrig, Marko T1 - Revision of IAEA Guidance Material for Package Load Attachment Points N2 - For transport operations according IAEA regulations SSR-6, the package shall be securely stowed and the package shall be capable to withstand specific effects, e.g. accelerations, during routine transport conditions. The supporting IAEA Advisory Material SSG-26 provides information how to do that. General information and detailed load factors for use in safety demonstrations are provided. Up to now package designers in different countries use other load factors for the design of attachment points than those specified in the IAEA guidance material. In particular the acceleration factors vary between different countries and lead to difficulties during the validation of foreign approval certificates. The background of the existing guidance including specified load values was not clear enough. The application of specified values and the boundary conditions, i.e. transport conditions, seemed to be improvable. The IAEA started a discussion process to review the existing guidance text. An international working group was constituted in 2013. Representatives came from different stakeholders, e.g. transport operators, competent authorities and modal organizations. The discussions concluded especially on the transport conditions which has to be considered for stowage design, including on the one hand the relevance of the load factors used for strength and fatigue analysis and, on the other hand the criteria which have to be considered for the attachment points. In addition, complementary questions relative to the operational aspects were discussed. Revised load values for different transport modes were proposed. The values are derived from standards and include safety factors now. As a result of those discussions, the international working group wrote new guidance material for stowage in transport, addressing all the previously quoted topics. T2 - WM2018 Conference CY - Phoenix, Arizona, USA DA - 18.03.2018 KW - Acceleration values KW - IAEA regulations KW - Routine conditions of transport PY - 2018 AN - OPUS4-44866 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wille, Frank T1 - Retaining Competence for Safe Transports of Radioactive Material N2 - The nuclear phase out in Germany will lead to a challenge finding skilled staff for all areas in nuclear business. Transport of spent fuel and high-level nuclear waste is an ongoing task over the next decades during the decommissioning of nuclear power plants and after the interim storage. The international regulations were adapted and address the issue of transports after storage now. The topic of aging and assessment of the development of the state-of-art technology are in focus. German research funds are supporting the investigations of future challenges of transport and storage of the nuclear heritage. BAM is involved and works on several topics related to the aging issue of packages. The behaviour of spent fuel claddings, long-term behaviour of metal and elastomeric gaskets and sensor/monitoring techniques of waste disposal are examples of research fields. T2 - 7th Nuclear Decommissioning & Waste Management Summit 2020 CY - London, UK DA - 12.02.2020 KW - Aging management KW - Transport KW - Spent fuel behaviour KW - Disposal PY - 2020 AN - OPUS4-50987 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weltschev, Margit A1 - Haufe, Manuela A1 - Kohl, Anka A1 - Rehfeldt, Rainer T1 - Resistance of polyethylene grades with permeation barriers in biofuels N2 - Biofuels including ethanol and biodiesel (FAME) represent a renewable fuel alternative to petroleum-derived transport fuels. The aim of this work was to study the interaction between high density polyethylene (HDPE) with permeation barriers in form of polyamide (PA) and fluorination, and biofuels such as E85 (fuel with 85 % ethanol), biodiesel and B10 (heating oil with 10 % biodiesel). 10 l jerrycans made of polyethylene with permeation barrier of PA were filled with E85 and biodiesel and exposed to temperatures of 20 °C and 40 °C for 5 years. Half of the 20 l jerrycans of HDPE for filling with B10 were fluorinated at the inner layer to prevent permeation before the exposure. Tensile properties were determined once a year, and FTIR-spectroscopy was used to evaluate possible changes. The tensile properties tensile strength and breaking elongation of HDPE jerrycan cuttings with permeation barrier decreased, but not significantly, after immersion in E85, biodiesel and B10. The elasticity modulus of the polyethylene grades was especially reduced during exposure to E85. The FTIR spectra of HDPE jerrycan cuttings with permeation barrier showed that immersion tests for five years with the test fuels at 20 °C and 40 °C did not lead to a decomposition of the permeation barriers. T2 - CORROSION 2018 CY - Phönix, Arizona, USA DA - 16.04.2018 KW - Polyethylene grades KW - Biofuels KW - Permeation barriers KW - FTIR spectra PY - 2018 AN - OPUS4-44758 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pötzsch, Sina A1 - Bäßler, Ralph A1 - Weltschev, Margit T1 - Resistance of metals exposed to heating oil blends with 10 % and 20 % biodiesel (FAME) N2 - In Europe biodiesel gained from rapeseeds are considered as an alternative to common fossil fuels due to its environmental performance and its independence from import of raw materials. Biodiesel is also suitable to serve as blending component to heating oil. In that case, it must be considered that changes of fuel composition might cause material degradation. The objective of this research was to investigate the resistance of metallic materials exposed to heating oil, heating oil blend B20 with 20 % biodiesel and pure biodiesel. Furthermore, the resistance of metals to eight-year aged B10 and six-year aged pure biodiesel was evaluated. Ageing of biodiesel forms acids and water which might propagate metal corrosion. The investigated metals (aluminium, unalloyed steel, austenitic CrNi-steel, copper, die cast zinc and brass) are commonly used for components in middle distillate facilities. According to DIN 50905-4 the immersed metals were exposed in a climate chamber at 50°C for 4 weeks. The metallic materials were evaluated as resistant if the annual corrosion rate due to uniform corrosion remained under 0.1 mm/year and no localized corrosion in the form of pitting occurred. The corrosion rates of the exposed materials stayed far below the limit of 0.1 mm/year for all tested fuels. An exception was die cast zinc ZP0410 in eight-year aged B10; a corrosion rate up to 0.3 mm/year due to uniform corrosion was measured. In no case localized corrosion occurred. Copper and brass caused discolouration of biodiesel from yellow to green. In conclusion, the tested metallic materials were resistant in heating oil, heating oil blend B20 and pure biodiesel at 50 °C. Even the metals exposed to six-year aged biodiesel and eight-year aged B10 showed no uniform or localized corrosion; except for zinc, which was not resistant in eight-year aged B10. T2 - EUROCORR 2019 CY - Sevilla, Spain DA - 09.09.2019 KW - Metals KW - Heating oil KW - Biodiesel KW - RME KW - Corrosion KW - Compatibility KW - FAME PY - 2019 AN - OPUS4-49137 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völzke, Holger A1 - Jaunich, Matthias A1 - Zencker, Uwe A1 - Simbruner, Kai A1 - Nagelschmidt, Sven A1 - Herbrich, Uwe A1 - Keller, Christian A1 - Qiao, Linan T1 - Research at BAM on Metal Seal Performance and Fuel Rod Integrity N2 - The presentation provides an update on preliminary results from research projects in the area of long term performance of metal seals and fuel rod integrity as safety relevant components of spent fuel transport and storage casks for spent nuclear fuel. T2 - Extended Storage Collaboration Program (ESCP) Winter Meeting 2020 CY - Online meeting DA - 09.11.2020 KW - Metal seal KW - Safety KW - Interim storage KW - Spent nuclear fuel KW - Fuel rod PY - 2020 AN - OPUS4-51615 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kömmling, Anja A1 - Jaunich, Matthias A1 - Grelle, Tobias A1 - Simbruner, Kai A1 - Zencker, Uwe A1 - Wolff, Dietmar A1 - Orellana Pérez, Teresa A1 - Völzke, Holger T1 - Research at BAM for evaluating long term safety of container systems and components N2 - Safety of long term containment and storage of radioactive waste is an essential issue, which is increasingly gaining international attention. Extending interim storage beyond initial license periods is one of the major challenges worldwide. BAM has been involved in all kinds of radioactive waste container safety evaluation for storage and transportation including their long term performance from the very beginning. Today, all work related to the safe management of radioactive waste is linked by the activity field “Nuclear Waste Management” within the Focus Area “Energy” at BAM and in conjunction with a research strategy and agenda. Most recently, the working group “Long Term Safety of Container Systems and Components” was established to launch and perform research projects related to safety issues concerning the extended interim storage of radioactive waste. For example, within our project LaMEP, we investigate ageing effects of metal and elastomer seals as well as polymeric neutron shielding materials, which are container components that fulfil major safety functions. The results of the experiments help to understand the long term behaviour of these components. Likewise, our project BRUZL started at BAM in 2018 with the aim of developing a fracture mechanics approach to understand and describe a potential brittle failure mechanism of fuel cladding during long-term interim storage. BAM also contributes to the GRS project “Development of methods and models and international exchange for safety evaluation in the frame of interim storage of radioactive waste”. Additionally, BAM is involved in several international research programmes dealing with extended interim storage, such as the European Joint Programme on Radioactive Waste Management (EURAD), the Extended Storage Collaboration Program (ESCP) and IAEA Coordinated Research Projects. The present contribution provides a comprehensive overview of BAM research activities contributing to national and international gap analyses and to filling knowledge gaps regarding the safe long term management of radioactive waste. T2 - Annual Meeting on Nuclear Technology 2019 CY - Berlin, Germany DA - 07.05.2019 KW - Radioactive Waste KW - Container Safety KW - Metal Seals KW - Elastomer Seals KW - Fuel cladding PY - 2019 AN - OPUS4-48437 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gröke, Carsten A1 - Neumann, Martin A1 - Komann, Steffen A1 - Wille, Frank T1 - Requirements for Package Design Testing and Quality Assurance Measures for Packages not Requiring Competent Authority Design Approval N2 - Übersicht über die gefahrgutrechtlichen Anforderungen zur Bauartprüfung und dem Qualitätsmanagement für Verpackungen für nicht zulassungspflichtige Versandstücke. T2 - KONTEC 2019 CY - Dresden, Germany DA - 27.03.2019 KW - Bauartprüfung KW - Qualitätsmanagement KW - Nicht zulassungspflichtig PY - 2019 AN - OPUS4-56352 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Martin A1 - Wille, Frank A1 - Kuschke, Christian A1 - Schubert, Sven A1 - Schilling, Olaf A1 - Günther, Uve A1 - Darnstädt, Andreas T1 - Requirements for management systems for manufacturing of transport packages: the new revision of BAM-GGR 011 guideline N2 - In accordance with IAEA SSR-6 para 306 a management system shall be established and implemented to ensure compliance with the relevant provisions of the IAEA regulations. BAM has issued an update of the guideline: the BAM-GGR 011. The new revision describes necessary quality assurance measures for design, manufacture, testing, documentation, use, maintenance and inspection of packagings for package designs requiring competent authority approval for the transport of radioactive material. The measures can be categorised as system-related and design-related. They are independently approved and monitored by the German competent authority BAM and its authorised expert (BAM/T). The qualification of the organisation applying for the design approval certificate is reviewed in the context of the design approval procedure. The quality assurance measures for manufacture consist of three main steps. Pre-assessment of manufacturing documents such as quality plans, specifications etc., Manufacturing inspections according the pre-assessed documents and inspection before commissioning including documentation review. Periodic inspections during operation as well as relevant specifications for use and maintenance ensure that the properties specified in the approval certificate are preserved over the package life time. Special provisions for the return on experience regarding operational feedback for design, manufacture, use, maintenance and inspection are given. Special focus shall be given here to the rearranged and meanwhile established system of manufacturing inspections. This includes more transparent roles for a) the producers authorised inspection 11282 representative, b) the independent inspection expert (S), acting on behalf of the manufacturer with acceptance of BAM, and c) BAM or its authorised expert (BAM/T). Additional attention shall be drawn to the management of deviations during manufacturing and provisions for maintenance and periodic inspections. T2 - 19th International Symposium on the Packaging and Transportation of Radioactive Materials PATRAM 2019 CY - New Orleans, LA, USA DA - 04.08.2019 KW - Quality assurance KW - Transport KW - Manufacturing KW - Surveillance KW - Radioactive material PY - 2019 AN - OPUS4-49056 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mair, Georg T1 - Relevante Entwicklungen zu Speichern für Gase als Energieträger N2 - Es werden die Zusammenhänge des Druckvolumenprodukts und der Konsequenz bei Druckgasen insbesondere für Wasserstoff dargestellt. Entsprechend werden Stellungnahmen zu verschiedenen Normungsprojekten abgeleitet und perspektivische Entwicklungen mit dem resultierenden Bedarf in der Normung dargestellt. Außerdem wird am Beispiel ein Problem in der praktischen Beurteilung von Speicherpopulationen für Batteriefahrzeuge diskutiert. T2 - 26. BAM-DIN-IGV-DVFG-Gespräch 2019 CY - Berlin, Germany DA - 27.02.2019 KW - Wasserstoffspeicher KW - Konsequenzbegrenzung KW - Normung KW - Druck-Volumen-Produkt KW - Katastrophe KW - Akzeptanz PY - 2019 AN - OPUS4-53145 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -