TY - CONF A1 - Schmidt, Anita T1 - Aktuelle Forschung - Technik für sichere Gefahrguttransporte N2 - Lithiumbatterien, Tanks und Druckgasflaschen: Ihnen ist gemeinsam, dass Gefahrguttransporte mit Ihnen sicher erfolgen müssen. Um dies zu gewährleisten, führt die BAM verschiedene Untersuchungen und Forschungsvorhaben durch. T2 - 35. Internationale Gefahrgut-Tage Hamburg CY - Hamburg, Germany DA - 17.02.2019 KW - Lithiumbatterien KW - Druckgefäße KW - Gefahrguttransport KW - ADR KW - Sicherheit PY - 2019 AN - OPUS4-50802 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Anita T1 - Aktuelles zur Sicherheit von Lithium-Ionen Akkus - Lagerung, Transporte, Brandschutzkonzepte N2 - Sicherheitskonzepte werden für die verschiedenen Szenarien für Lithiumakkus benötigt: Vor allem für den Bereich der Lagerung gibt es im Moment nur wenige Vorgaben. Im Vortrag werden verschiedene Brandschutzkonzepte vorgestellt. Für die Lagerung werden Empfehlungen ausgesprochen, die teilweise an die Vorgaben der Transportvorschriften anknüpfen. T2 - Forum 2019 zur Schadenverhütung der Arbeitsgemeinschaft Berlin Brandenburg (AGS) und AGBB Berlin e.V. CY - Berlin, Germany DA - 23.10.2019 KW - Lithiumbatterien KW - Brandschutzkonzepte KW - Lagerung KW - Gefahrguttransport PY - 2019 AN - OPUS4-50807 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Anita T1 - Zulassungsregeln für Verpackungen von Lithiumbatterien N2 - Sicherer Transport defekter Batterien im Aufgabenbereich der BAM. T2 - 12. Fachkonferenz Lithiumbatterien CY - Frankfurt a.M., Germany DA - 21.01.2019 KW - Lithiumbatterien KW - ADR KW - Gefahrguttransport PY - 2019 AN - OPUS4-50803 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Anita T1 - New ADR regulations for critical lithium batteries N2 - End of life batteries may be damaged or defective and may cause the risk of dangerous reactions. New ADR regulations allow them nevertheless to be tansported with the specifications of the national competent authority. BAM's approach. T2 - End-of-Life Batteries from Electrified Vehicles CY - Fredrikstad Oslo, Norway DA - 13.06.2019 KW - Dangerous goods KW - Defective Lithium batteries KW - ADR KW - Transport PY - 2019 AN - OPUS4-50801 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Linnemann, Konrad T1 - Experimental and numerical analyses of spent nuclear fuel behavior under transport conditions N2 - Packages for the transport of spent nuclear fuel shall meet the International Atomic Energy Agency regulations to ensure safety under different transport conditions. The physical state of the spent fuel and the fuel rod cladding as well as the geometric configuration of fuel assemblies are important inputs for the evaluation of the package capabilities under these conditions. The mechanical behavior of spent fuel assemblies shall be analyzed with regard to the assumptions which are used in the containment and criticality safety analysis. The package as a mechanical system is characterized by a complex set of interactions, e. g. between the fuel rods within the assembly as well as between the fuel assemblies, the basket, and the cask containment. This complexity makes it difficult to assume appropriate mechanical loads for the spent fuel inside the package. Another challenge is the assumption of material properties which represent the variation of the fuel rods regarding cladding material, burn-up and the operation history sufficiently. The objective of this paper is to give an overview about the current approaches and research for the evaluation of spent fuel behavior within the package design approval procedure. In this context, analytical, numerical and experimental results are discussed. The presented work is achieved within a collaboration of BAM with national and international partners. T2 - Abteilungskolloquium 3.3 CY - Berlin, BAM Fabeckstraße DA - 02.10.2019 KW - Transportbehälter KW - Radioaktive Stoffe KW - Brennelementverhalten KW - FE-Berechnungen PY - 2019 AN - OPUS4-51173 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Quercetti, Thomas T1 - Drop Testing of a New Package Design for the Transport of SNF from German Research Reactors N2 - A new dual purpose cask design was developed for the safe transport and interim storage of spent fuel elements of German research reactors. In the framework of the safety assessment within the package approval procedure the Bundesanstalt für Materialforschung und –prüfung (BAM) as competent authority performed a series of drop tests according with the IAEA Transport Regulations. The package consists of a cylindrical thick-walled ductile cast iron cask body closed by a bolted lid system with metallic seals. A lid and bottom sided impact limiter consisting of a wood/steel construction limit the mechanical impact loading. The full-scale test specimen was equipped with a basket and assembled with dummy-fuel elements. The package and test specimen, respectively have a total mass of approximately 24 metric tons. The mechanical drop test program included three 9m free drop tests, in horizontal, vertical and oblique cask orientation onto the lid system. Additionally, a 1m-puncture bar drop test followed the horizontal drop test to consider an IAEA-drop test sequence. The horizontal and vertical drop tests were performed at a temperature of minus 40°C. During the oblique drop test the upper impact limiter was heated up to +80°C. The tests were conducted onto an unyielding target, fulfilling the IAEA requirements. The test specimen was considerably instrumented with strain gauges and accelerometers. Transient strains at selected locations of the inner and outer container walls, of the primary and secondary lid, as well as of the corresponding lid bolts were measured during the drop tests. Furthermore, decelerations in different locations at the cask body and the lids were measured. The complex geometrical deformation of the impact limiters due to the impact were determined by optical 3D- measurements. Before and after the drop tests the leakage rate of the lid system was determined by helium leakage testing. The experimental results contribute to the evaluation of the package response to mechanical tests, demonstrating safety under normal and accident conditions of transport and especially to the verification of the dynamic finite-element model of the package used in the package design safety report. T2 - PATRAM 2019 CY - New Orleans, LA, USA DA - 04.08.2019 KW - SNF KW - Drop testing KW - New package design PY - 2019 AN - OPUS4-50623 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tschirschwitz, Rico T1 - Auswirkungen beim Versagen von Energiespeichern - Druckbehälter und Lithium-Ionen-Batterien N2 - Immer wieder kommt es bei Bränden zum Bersten von Propan- und Acetylenflaschen. Im Falle eines Behälterversagens stellen diese eine enorme Gefährdung für die Einsatzkräfte dar. Die BAM beschäftigt sich seit vielen Jahren mit den Auswirkungen im Falle eines solchen Behälterversagens. Der erste Teil des Beitrages stellt die Arbeit der BAM auf diesem Gebiet vor und zeigt verschiedene Handlungsoptionen auf, um das Risiko für Einsatzkräfte zu verringern. Im zweiten Teil des Beitrages werden die aktuellen Aufgaben und bisherigen Aktivitäten zur Sicherheit von Lithiumbatterien vorgestellt. Weiterhin werden die Versuchsmöglichkeiten auf dem BAM TTS und die derzeit im Aufbau befindlichen messtechnischen Systeme zur Quantifizierung der Auswirkungen beim Versagen von Lithiumbatterien dargestellt. T2 - Gemeinsame Fortbildungsveranstaltung der Fachvereinigung Arbeitssicherheit e. V. sowie der gesetzlichen Unfallversicherungen, Berufsgenossenschaften der Bauwirtschaft Berlin CY - Berlin, Germany DA - 24.10.2019 KW - Behälterversagen KW - LPG KW - Lithiumbatterien KW - Alternative Antriebe KW - Auswirkungsbetrachtung PY - 2019 AN - OPUS4-49476 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Martin T1 - Maintenance and periodic inspections for packagings not requiring CA-approval N2 - In this presentation the main requirements of BAM-GGR 016 regarding maintenance and periodic inspections were explained. BAM ensures during acceptance of the quality management program that specific and relevant instructions for maintenance and periodic inspections are developed and handed to the operator of the packaging. Examples are given. T2 - FORO Iberoamericano CY - Madrid, Spain DA - 25.11.2019 KW - Maintenance KW - Periodic inspections KW - Radioactive material KW - Package PY - 2019 AN - OPUS4-50049 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Oesch, Tyler T1 - In-situ Röntgencomputertomographie für mechanische, thermische und hydraulische Prozesse N2 - Die Präsentation demonstriert die Fähigkeiten der Röntgencomputertomographie (CT) zur Identifizierung quantitativer Materialeigenschaften wie Faserorientierung und Korrosionsverteilung sowie die Implementierung von CT-Daten innerhalb numerischer Simulationen. Die besondere Stärke der CT, als zerstörungsfreies Prüfverfahren, ermöglicht es, das Materialverhalten und den Versagensprozess während mechanischer, hydraulischer und thermischer Prozesse zu beobachten. Die Ergebnisse einer Reihe von Ex-situ und In-situ Testprogrammen unter Bedingungen wie mechanische Belastung, Wassertransport und thermische Exposition, stellen die Nutzungsmöglichkeiten dieser Verfahren in Kombination mit der CT in eindrucksvoller Weise dar. T2 - InnoTesting Konferenz CY - Wildau, Germany DA - 21.02.2019 KW - Röntgencomputertomographie (CT) KW - In-situ Prüfverfahren KW - Feuchtigkeitsmessung KW - Digitale Bildkorrelation (DVC) KW - Faserverstärkter Beton (FRC) PY - 2019 AN - OPUS4-47442 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wosniok, Aleksander T1 - Intelligente Geokunststoffe – Nachhaltige Zustandsüberwachung durch ortsaufgelöste faseroptische Messsysteme N2 - Vorstellung von Entwicklungsarbeiten zum Thema sensorbasierte Geokunststoffe mit integrierten faseroptischen Sensoren. T2 - IAB-Baustoff-FORUM 2019 CY - Weimar IAB, Germany DA - 06.03.2019 KW - Faseroptischer Sensor KW - Verteilter Sensor KW - Ortsaufgelöste Messung KW - Intelligente Geokunststoffe PY - 2019 AN - OPUS4-47508 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -