TY - CONF A1 - Breese, Philipp Peter T1 - In-situ defect detection for laser powder bed fusion with active laser thermography N2 - Defects are still common in metal components built with Additive Manufacturing (AM). Process monitoring methods for laser powder bed fusion (PBF-LB/M) are used in industry, but relationships between monitoring data and defect formation are not fully understood yet. Additionally, defects and deformations may develop with a time delay to the laser energy input. Thus, currently, the component quality is only determinable after the finished process. Here, active laser thermography, a non-destructive testing method, is adapted to PBF-LB/M, using the defocused process laser as heat source. The testing can be performed layer by layer throughout the manufacturing process. The results of the defect detection using infrared cameras are presented for a custom research PBF-LB/M machine. Our work enables a shift from post-process testing of components towards in-situ testing during the AM process. The actual component quality is evaluated in the process chamber and defects can be detected between layers. T2 - 2023 Annual International Solid Freeform Fabrication Symposium CY - Austin, TX, USA DA - 14.08.2023 KW - Additive Manufacturing KW - Additive Fertigung KW - Laser Powder Bed Fusion KW - Nondestructive Testing KW - Flying Spot Laser Thermography PY - 2023 AN - OPUS4-58137 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bruno, Giovanni T1 - In-Situ Compression CT on Additively Manufactured in 625 Lattice Structures N2 - The porosity and the surface roughness are recently discussed problems for SLM parts. The influence of SLM process parameters on porosity is well studied for different materials. Nevertheless, the build angle (i.e. the angle between part orientation and build plate) needs to be understood as an additional SLM process parameter, as it has been shown, that the microstructure and hence the mechanical performance of various materials depend on the build angle. The inherent build angle of each strut as a part of a lattice structure is the motivation to investigate the influence of the build angle on the porosity and roughness on round-shaped (1 mm diameter) struts by means of CT. Conventional Coordinate Measuring Machine (CMM) has the limitation towards small and round shaped samples. The need for Computed Tomography (CT) regarding investigations of SLM parts will increase because no other non-destructive technique allows the assessment of complex geometries with inner laying surfaces. We used CT to assess the pores and the strut surface. Seven struts out of the nickel alloy Inconel 625 with build angles from 30° to 90° were studied. It was found that the number of pores is smaller, and the size of pores is larger for the 90° strut. In case of 30° strut, the number of pores is increased towards down-skin side, additionally, this strut orientation showed to have the largest number of attached powder particles. The elongated pores exist exclusively near the strut surface. While the roughness at the down-skin surface is highly depending of the biud angle, the roughness at the up-skin surface is the same for all struts. The mechanisms of pore and surface roughness formation is not mainly driven by gravity. T2 - ISAM Konferenz 2019 CY - Dresden, Germany DA - 29.01.2019 KW - Computed Tomography KW - Additive Manufacturing KW - Metals KW - Microstructure PY - 2019 AN - OPUS4-47327 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mohr, Gunther T1 - In situ thermography and optical tomography in LBM - comparison to CT N2 - - Successful proof of concept of synchronous in-situ monitoring of a L-PBF process by thermography and optical tomography - Examination method for data analysis - Identification of correlations between measured signals and defects - Identification of sources of misinterpreting T2 - Workshop on Additive Manufacturing: Process , materials , simulation & implants CY - Berlin, Germany DA - 13.05.2019 KW - Laser Powder Bed Fusion KW - Thermography KW - Optical Tomography KW - Computed Tomography KW - Additive Manufacturing KW - 3D printing PY - 2019 AN - OPUS4-48521 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mohr, Gunther T1 - In situ heat accumulation by geometrical features obstructing heat flux and by reduced inter layer times in laser powder bed fusion of AISI 316L stainless steel N2 - Material qualification for laser powder bed fusion (L-PBF) processes are often based on results derived from additively manufactured (AM) bulk material or small density cubes, although it is well known that the part geometry has a tremendous influence on the heat flux and, therefore, on the thermal history of an AM component. This study shows experimentally the effect of simple geometrical obstructions to the heat flux on cooling behavior and solidification conditions of 316L stainless steel processed by L-PBF. Additionally, it respects two distinct inter layer times (ILT) as well as the build height of the parts. The cooling behavior of the parts is in-situ traced by infrared (IR) thermography during the built-up. The IR signals reveal significant differences in cooling conditions, which are correlated to differences in melt pool geometries. The acquired data and results can be used for validation of computational models and improvements of quality assurance. T2 - 11th CIRP Conference on Photonic Technologies (LANE 2020) CY - Online meeting DA - 07.09.2020 KW - Additive Manufacturing PY - 2020 AN - OPUS4-51255 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altenburg, Simon T1 - Improving additive manufacturing technologies by in-situ monitoring: Thermography N2 - Additive manufacturing of metals gains increasing relevance in the industrial field for part production. However, especially for safety relevant applications, a suitable quality assurance is needed. A time and cost efficient route to achieve this goal is in-situ monitoring of the build process. Here, the BAM project ProMoAM (Process monitoring in additive manufacturing) is briefly introduced and recent advances of BAM in the field of in-situ monitoring of the L-PBF and the LMD process using thermography are presented. T2 - Anwenderkonferenz Infratec GmbH CY - Online meeting DA - 04.11.2021 KW - Additive Manufacturing KW - Process monitoring KW - Thermography PY - 2021 AN - OPUS4-54026 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Breese, Philipp Peter T1 - Hyperspektrale Thermografie im metallischen Laser-Pulverbettschweißen (PBF-LB/M): Grundlagen für eine in-situ Realtemperatur-Bestimmung N2 - Die additive Fertigung (Additive Manufacturing AM, auch als 3D Druck bekannt) von Metallen nimmt einen stetig wachsenden Stellenwert in industriellen Anwendungen ein. Gründe dafür sind u.a. die Möglichkeit der Umsetzung komplexer Bauteildesigns und die Nutzung neuartiger Werkstoffe. Damit hebt sich AM von konventionellen Fertigungsmethoden wie der subtraktiven Fertigung (Drehen, Fräsen, etc.) ab. Das für Metalle am weitesten verbreitete AM-Verfahren ist das Laser-Pulverbettschweißen (Laser Powder Bed Fusion PBF-LB/M, auch als Selective Laser Melting SLM bekannt). Es besitzt aktuell den höchsten Industrialisierungsgrad und die größte Anzahl an eingesetzten Maschinen. Bei PBF-LB/M liegt der metallische Ausgangswerkstoff unter Inertgasatmosphäre innerhalb einer Prozesskammer in einem Bett als Pulver vor und ein Laser schmilzt dieses lokal auf. Durch wiederholtes Auftragen einer neuen Pulverschicht und anschließendes selektives Schmelzen mit Hilfe des Lasers findet der lagenweise Aufbau eines Bauteils statt. Die dabei auftretenden lokalen Temperaturverteilungen bestimmen sowohl die Eigenschaften des gefertigten Bauteils als auch das mögliche Auftreten von Defekten wie Poren oder Risse. Durch diese Relevanz der thermischen Historie wäre die Aufzeichnung der auftretenden Realtemperaturen in zeitlicher und räumlicher Abhängigkeit optimal. Mit quantitativen Werten wären Vergleichbarkeit und Wiederholbarkeit des AM-Prozesses gegeben, was sich auch positiv auf Qualität und Sicherheit des gefertigten Bauteils auswirkt. Außerdem wäre ein Beitrag zur Validierung von Simulationen sowie zur Gewinnung eines tieferen Verständnisses des Fertigungsprozesses gegeben. Jedoch findet aktuell lediglich ein qualitatives Monitoring statt (bspw. mittels Überwachung des Schweißbades durch eine Photodiode) und sicherheitsrelevante Bauteile müssen zeit- und kostenaufwändig im Nachgang ex-situ geprüft werden. Grund dafür sind auch die herausfordernden Bedingungen des PBF-LB/M-Prozesses mit hohen Scangeschwindigkeiten bei geringem Durchmesser des Laserspots. Des Weiteren erschweren die auftretenden Emissionsgradänderungen mit hoher Dynamik (zeitlich, räumlich) und den gegebenen Abhängigkeiten (temperatur-/wellenlängenabhängig) eine berührungslose Temperaturbestimmung basierend auf emittierter Infrarotstrahlung deutlich. Klassische Thermografie bietet zwar sehr gute qualitative Einblicke, ist dabei jedoch ohne eine aufwändige Temperaturkalibrierung inklusive Bildsegmentierung und Zuweisung von vorher ermittelten Emissionsgraden für eine verlässliche Bestimmung der Realtemperatur nicht ausreichend. Aus diesem Grund wird in dieser Veröffentlichung der Ansatz der hyperspektralen Thermografie für den PBF-LB/M Prozess vorgestellt: Die emittierte Infrarotstrahlung wird gleichzeitig bei einer Vielzahl von benachbarten Wellenlängenbereichen gemessen. Dies wird in dieser Untersuchung mittels einer selbst zusammengestellten hyperspektralen Linienkamera, die im kurzwelligen Infrarotbereich arbeitet, realisiert. Hierbei wird die thermische Strahlung einer Linie auf dem Messobjekt spektral aufgespalten und detektiert, sodass die spektrale spezifische Ausstrahlung entlang dieser Linie vermessen werden kann. Bewegt sich das Schmelzbad des PBF-LB/M Prozesses bei ausreichender Bildfrequenz durch diese Linie, ist eine räumliche Rekonstruktion eines effektiven Schmelzbades möglich. Ein Ansatz, um aus diesen hyperspektralen Daten die gesuchten Emissionsgrade sowie die Realtemperatur zu ermitteln, sind Methoden der Temperatur-Emissionsgrad-Separation (TES). Ein Hauptproblem besteht darin, dass n spektrale Messungen verfügbar sind, jedoch n+1 Kenngrößen für jeden Bildpixel gesucht werden (n Emissionsgrade + eine Temperatur). TES-Methoden liefern die Möglichkeit, dieses mathematisch unterbestimmte Problem verlässlich und nachvollziehbar zu approximieren, indem der spektrale Emissionsgrad mit wenigen Freiheitsgraden analytisch parametriert wird. Mit Hilfe dieses Ansatzes werden Setup und Methoden an SAMMIE (Sensor-based Additive Manufacturing Machine), einer Forschungsmaschine für PBF-LB/M, angewendet. Erste Ergebnisse unter AM-Prozessbedingungen werden gezeigt, welche die Grundlage für die Bestimmung von Realtemperaturen im PBF-LB/M-Prozess bilden. Dies leistet einen wichtigen Beitrag zur verbesserten Vergleichbarkeit und Wiederholbarkeit der Fertigung, zur Validierung von Simulationen sowie zum Verständnis des Prozesses selbst. Das unterstützt langfristig dabei das Vertrauen in die Sicherheit von AM-Produkten zu stärken. T2 - TEMPERATUR 2024 CY - Berlin, Germany DA - 05.06.2024 KW - Additive Manufacturing KW - Laser Powder Bed Fusion KW - Schmelzbadtemperatur KW - Hyperspectral Imaging KW - Emissionsgrad KW - Quantitative Temperatur PY - 2024 AN - OPUS4-60753 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bruno, Giovanni A1 - Fritsch, Tobias A1 - Schröder, Jakob A1 - Mishurova, Tatiana A1 - Ulbricht, Alexander A1 - Evans, Alexander A1 - Serrano-Munoz, Itziar T1 - How to experimentally determine residual stress in AM structures N2 - The experimental determination of residual stress becomes more complicated with increasing complexity of the structures investigated. Unlike the conventional and most of the additive manufacturing (AM) fabrication techniques, laser powder bed fusion (PBF-LB) allows the production of complex structures without any additional manufacturing step. However, due to the extremely localized melting and solidification, internal stress-induced deformation and cracks are often observed. In the best case, significant residual stress is retained in the final structures as a footprint of the internal stress during manufacturing. Here we report solutions to the most prevalent challenges when dealing with the diffraction-based determination of residual stress in AM structures, in particular the choice of the correct diffraction elastic constants. We show that for Nickel-based alloys, the diffraction elastic constants of AM material significantly deviate from their conventional counterparts. Furthermore, measurement strategies to overcome the hurdles appearing when applying diffraction-based techniques to complex-shaped lattice structures are presented: a) proper sample alignment within the beam, b) the proper determination of the residual stress field in a representative part of the structure (i.e., with an engineering meaning). Beyond the principal stress magnitude, the principal direcions of residual stress are discussed for different geometries and scan strategies, as they are relevent for failure criteria. We show that the RS in the lattice struts can be considered to be uniaxial and to follow the orientation of the strut, while the RS in the lattice knots is more hydrostatic. Additionally, we show that strain measurements in at least seven independent directions are necessary for the correct estimation of the principal stress directions. The measurement directions should be chosen according to the sample geometry and to an informed choice on the possible strain field (i.e., reflecting the scan strategy). We finally show that if the most prominent direction is not measured, the error in the calculated stress magnitude increases in such a manner that no reliable assessment of RS state can be made. T2 - Additive 2024 CY - Berlin, Germany DA - 12.06.2024 KW - Neutron Diffraction KW - Residual Stress KW - X-ray Computed Tomography KW - Additive Manufacturing KW - Lattice Structure KW - Inconel PY - 2024 AN - OPUS4-60423 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bruno, Giovanni T1 - How 3D X-ray Imaging and Residual Stress Analysis contribute to safety of materials and structures N2 - The safety of materials and structures can be detrimentally influenced by residual stresses (RS) and defect populations (voids or other features leading to failure) if they are not correctly accounted for in the design. Therefore, the accurate characterization of these features and the consideration of their impact is crucial for the safe design of components. The ability to characterize these features non-destructively enables the direct correlation on resulting mechanical performance. 3D X-ray computed tomography (XCT) is used to resolve and quantitively analyze microstructural features (i.e., voids, porosity). This is often used to assess the capability of the manufacturing route, i.e., additive manufacturing (AM). The non-destructive nature of the method also enables the study of the evolution of damage in materials from such microstructural features [1]. Using in-situ methods such as compression or tension, the propagation of damage from initial microstructure can be assessed, aiding our understanding of which features are detrimental to safety [3]. Diffraction based residual stress analysis methods including high energy X-ray and neutron diffraction can be used to study the residual stress gradients from the surface, subsurface and into the bulk non-destructively. These methods can be used to study the influence of heat treatments on residual stress and can be combined with XCT results to correlate the interaction of residual stresses with microstructural features (i.e., void clusters). This talk will give an overview of the capabilities and opportunities of 3D XCT and diffraction based residual stress analysis to close the gap in our understanding of material degradation on mechanical performance, enabling manufacturers to adjust their designs accordingly for safety critical applications. A particular focus will be made on examples where the two advanced techniques are combined to enhance such understanding. T2 - MaterialsWeek 2025 CY - Frankfurt am Main, Germany DA - 02.04.2025 KW - Neutron Diffraction KW - Residual Stress KW - X-ray Computed Tomography KW - Additive Manufacturing KW - Large Scale facilites KW - Creep KW - Defects KW - BAMline PY - 2025 AN - OPUS4-62895 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bhadeliya, Ashok T1 - High Temperature Fatigue Crack Growth in Nickel-Based Alloys Refurbished by Additive Manufacturing and Brazing N2 - Hybrid additive manufacturing plays a crucial role in the restoration of gas turbine blades, where e.g., the damaged blade tip is reconstructed by the additive manufacturing process on the existing blade made of a parent nickel-based alloy. However, inherent process-related defects in additively manufactured material, along with the interface created between the additively manufactured and the cast base material, impact the fatigue crack growth behavior in bi-material components. This study investigates the fatigue crack growth behavior in bi-material specimens of nickel-based alloys, specifically, additively manufactured STAL15 and cast alloy 247DS. The tests were conducted at 950 °C with stress ratios of 0.1 and -1. Metallographic and fractographic investigations were carried out to understand crack growth mechanisms. The results revealed significant retardation in crack growth at the interface. This study highlights the potential contributions of residual stresses and microstructural differences to the observed crack growth retardation phenomenon, along with the conclusion from an earlier study on the effect of yield strength mismatch on crack growth behavior at a perpendicular interface in bi-material specimens. T2 - Superalloys 2024 Conference CY - Champion, PA, USA DA - 08.09.2024 KW - Fatigue crack growth KW - Bi-material structure KW - Nickel-based alloys KW - Additive Manufacturing KW - Brazing PY - 2024 AN - OPUS4-61047 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sprengel, Maximilian T1 - Heat treatment induced residual stress relaxation in additively manufactured L-PBF 316L stainless steel N2 - Residual stress relaxation as a function of heat treatment strategies in laser based powder bed fused 316l samples. T2 - Eleventh Joint BER II and BESSY II User Meeting CY - Berlin, Germany DA - 04.12.2019 KW - Additive Manufacturing KW - Residual Stress KW - Neutron Diffraction KW - 316L PY - 2019 AN - OPUS4-49851 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -