TY - CONF A1 - Geburtig, Anja T1 - UV radiation and light as impact factors N2 - Radiation in the spectral ranges of UV and VIS are environmental impact factors that can cause ageing of many materials or products. The reason for this is that especially organic materials, such as food or many pharmaceutical, are subject to photochemical degradation. Of course, suited transparent packaging material may give protection against such impact for radiation sensitive fillings. But for this, it is necessary to know about the spectral range of the fillings sensitivity as well as about the radiation impact of the radiation sources that are relevant during the life time of the product. The spectral irradiance for characterizing the emission of various radiation sources is easily measured by means of a spectroradiometer. The spectral sensitivity of a filling's property can be determined by spectrally dispersed irradiation, where the positions on a sample are related to the different wavelengths. Thus, the damaging effect of the different wavelengths can be directly evaluated. A lateral measurement of the relevant property change shows the activation spectrum, which is the product of the spectral radiant exposure and the spectral sensitivity. By measuring the spectral irradiance for each sample position, the spectral sensitivity of the ageing property can be calculated. Comparing the fillings spectral sensitivity and the spectral irradiance of a potential radiation source during later transport and storage, conclusions can be drawn about necessary spectral absorption of a (partly) transparent packaging to give sufficient protection. The setup for such investigation will be shown and several illustrating samples from daily food experience will be given. T2 - 20th IAPRI World Conference on Packaging CY - Campinas, Brazil DA - 12.06.2016 KW - UV radiation KW - Light KW - Spectral sensitivity KW - Spectral irradiance KW - Spectral absorption PY - 2016 SN - 978-85-7029-136-3 SP - 136 EP - 139 AN - OPUS4-36913 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Trubiroha, Peter A1 - Geburtig, Anja A1 - Wachtendorf, Volker T1 - Grundsätzliches zur witterungsbedingten Alterung von Polymerwerkstoffen T2 - SKZ-Fachtagung "Bewitterung von Kunststoffen und Lacken in der Automobilindustrie" CY - Würzburg, Deutschland DA - 2005-02-16 KW - Witterung KW - Alterung KW - Klima KW - Vorgeschichte KW - Prüfverfahren KW - Prüfgeräte PY - 2005 SP - 36 Seiten PB - SKZ CY - Würzburg AN - OPUS4-7099 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker A1 - Geburtig, Anja A1 - Trubiroha, P. ED - Ziegahn, K.-F. T1 - Messung der effektiven UV-Bestrahlung bei der Bewitterung von Polymeren N2 - Bei der Bestrahlung und Bewitterung von polymeren Werkstoffen wird die Degradation durch eine Absorption von Strahlung initiiert und meistens durch weitere Klimagrößen, wie z.B. Wärme, Feuchte und atmosphärische Gase beeinflusst. Die Messung einer effektiven Bestrahlungsstärke und ihre zeitliche Integration sind deshalb von großer Bedeutung und zwar sowohl für die Kontrolle der Funktion des Bewitterungs- oder Bestrahlungsgerätes als auch als zusätzliche Angabe der wirkenden Beanspruchung. Photochemische Prozesse werden beim Sehen oder allgemeiner bei Farbstoffen schon durch sichtbare (VIS) Strahlung, dagegen bei der Erythembildung der Haut und der Photodegradation von Polymeren erst durch die energiereicheren Photonen der ultravioletten (UV) Strahlung initiiert. Die spektrale Empfindlichkeit des Auges und die Erythembildung sind im VIS- bzw. UV-Bereich sehr stark wellenlängenabhängig, was durch die Angabe der mit der spektralen Hellempfindlichkeit V(λ) des Auges bewerteten VIS-Strahlung in Lux (lx) bzw. die mit der Erythem-Wirkfunktion Serythem bewertete UV Strahlung als dimensionsloser UV-Index berücksichtigt wird. Spektrale Empfindlichkeiten. Die Photodegradation von Polymeren ist im UV-Bereich ebenfalls stark wellenlängenabhängig, was bisher bei der radiometrischen UV-Messung nicht berücksichtigt wurde. Seit Mitte der 70er Jahre, als die lx- bzw lxh- Messung bei der Strahlungsbeanspruchung langsam durch die Ermittlung der radiometrischen UV-Bestrahlungsstärke bzw. der UV-Bestrahlung im gesamten UV-Bereich abgelöst wurde, gab es hier bei der Bewitterungsprüfung keine weiteren Fortschritte auf dem Gebiet der Charakterisierung der Strahlungsbeanspruchung im UV-Bereich. Seit Jahren liegen zahlreiche Ergebnisse über die spektrale Empfindlichkeit von Photo-degradationsprozessen vor, die zeigen, dass die spektrale Empfindlichkeit im Bereich der Globalstrahlung an der kurzwelligen Grenze bei ca. 300 nm, am größten ist und im langwelligen UV-Bereich bei ca. 400 nm gegen Null geht. Die Messungen der radiometrischen Größen UV-Gesamtbestrahlungsstärke und UV-Gesamtbestrahlung erfasst deshalb über weite Wellenlängenbereiche Strahlungsanteile, die für die Photodegradation bedeutungslos sind und mittelt über potenziell bedeutsame Änderungen im kurzwelligen UV-Bereich hinweg. Es wird das Konzept eines neuen UV-Radiometers vorgestellt, dessen spektrale Empfindlichkeit einer mittleren spektralen Empfindlichkeit der Photodegradation von Polymeren entspricht. Die effektive UV-Bestrahlungsstärke und UV-Bestrahlung kann dadurch wesentlich genauer erfasst werden. T2 - 48. Jahrestagung der GUS 2019 CY - Stutensee, Germany DA - 27.03.2019 KW - UV-Bestrahlungsstärke PY - 2019 SN - 978-3-9818507-3-4 SP - 89 EP - 100 AN - OPUS4-47896 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja T1 - Possibilities on prediction of plastic’s fragmentation time - Digital twins for decomposing-time predictions N2 - Depending on the specific plastic’s ageing sensitivities, the durations which plastic components remain in the environment can be very long. As, in the past, the advantages in ageing resistance and durability were highly evaluated, we now face the problem of quite stable plastic waste within the environment. However, there is only little knowledge on the real timescales until macroscopic fragmentation for the different kinds of plastic under various environmental conditions. Here, weathering methods are presented, which have been used for the failure prediction in specific outdoor conditions. Issues of uncertainty, reproducibility, or validation are discussed. For the prediction of the plastic’s fragmentation, much longer time scales have to be considered. To do this within a limited project life span, various processes as well as their acceleration potential have to be evaluated separately, such as temperature increase or spectral shift. The possibilities and limitations of such controlled acceleration will be discussed. T2 - 29th IAPRI Symposium on Packaging CY - Twente, Enschede, The Netherland DA - 11.06.2019 KW - Digital twin KW - Plastic KW - Ageing KW - Environment KW - Fragmentation PY - 2019 SN - 978-90365-4731-4 SP - 630 EP - 631 PB - University of Twente CY - Twente, Enschede, The Netherlands AN - OPUS4-48238 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Aktuelles aus dem BAM-Fachbeirat N2 - Die Anforderungen an Geokunststoffprodukte und deren Qualitätssicherung unterliegen einem stetigen Wandel, der sowohl durch technische Veränderungen als auch durch normative und organisatorische Entwicklungen geprägt ist. Insbesondere der Fachbeirat der BAM gemäß Deponieverordnung (DepV) spielt hier im Bereich der Deponietechnik eine wichtige Rolle. An dieser Stelle sollen aktuelle Themen aus dem Fachbeirat der BAM vorgestellt werden, die wesentliche Änderungen in der Zulassungs- und Anwendungspraxis betreffen. Der Beitrag beleuchtet unter anderem Veränderungen innerhalb der BAM, die Modernisierung der Publikationsformate sowie die fachliche Weiterentwicklung der Zulassungsrichtlinien. T2 - 22. Leipziger Deponiefachtagung CY - Leipzig, Germany DA - 10.03.2026 KW - Deponie KW - Geotextil KW - Abdichtungssystem PY - 2026 SN - 978-3-00-085899-4 VL - 22 SP - 15 EP - 22 PB - HWTK Leipzig CY - Leipzig AN - OPUS4-65664 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Averin, Anton A1 - Hirsch, Philipp Daniel A1 - Lecompagnon, Julien T1 - Thermographic Reference Dataset: Defect Detection in Nuclear Waste Barrel Cutouts Using Long Pulse Thermography N2 - We introduce a thermographic dataset for subsurface defect detection in radioactive waste storage drums, comprising thermal sequences from 7 barrel specimens with artificially manufactured internal defects. The dataset was acquired using cost-effective halogen-lamp excitation (2kW per lamp) as an alternative to laser-based systems, with dual-camera thermal imaging (CMOS and bolometric) to enable performance comparison across imaging modalities. The specimens include both new and aged barrel types with controlled defects — FBHs, lines, crosses, triangles, and rectangles — simulating internal corrosion at varying scales (4mm to 60mm). Three heating regimes (both lamps, left only, right only) were systematically applied across multiple measurement regions per sample, yielding normalized thermal sequences. To lower the barrier for machine learning practitioners without thermography expertise, the dataset provides pre-computed features derived from principal component analysis, pulse phase thermography, and independent component analysis extracted using experimentally optimized time windows. Ground-truth binary masks mapping defect locations are included to enable supervised learning. This resource is designed to support the development and benchmarking of automated defect detection algorithms for non-destructive testing of curved, thin-walled metallic structures under realistic surface conditions (paint inhomogeneity, dirt, geometric artifacts), while validating low-cost thermographic inspection alternatives for industrial deployment. KW - Nondestructive Testing KW - Corrosion detection KW - Waste storage KW - Thermography KW - Safety PY - 2026 DO - https://doi.org/10.5281/zenodo.18916290 PB - Zenodo CY - Geneva AN - OPUS4-65666 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stelzner, Ludwig A1 - Kobe, André A1 - Pittrich, Tim T1 - Konstruktiver Brandschutz: Abplatzverhalten von Beton, Innovativer Versuchsaufbau und klinkereffiziente Zemente N2 - Bauteile aus Beton besitzen in der Regel ohne zusätzliche Schutzmaßnahmen aufgrund ihrer großen Masse, der Nichtbrennbarkeit des Baustoffs sowie der geringen Wärmeleitfähigkeit einen hohen Feuerwiderstand. Jedoch kann der Querschnitt durch Abplatzungen im Brandfall reduziert und die Bewehrung freigelegt werden. Dies kann zum frühzeitigen Verlust der Standsicherheit und in der Folge insbesondere bei Infrastrukturbauwerken zu massiven ökonomischen Folgeschäden führen. Der Beitrag präsentiert aktuelle Forschungsarbeiten der BAM zur Analyse des Abplatzverhaltens von Beton. Auf Basis experimenteller Untersuchungen zum Einfluss der Prüfkörpergröße auf das Abplatzverhalten wird eine weiterentwickelte Prüfmethodik vorgestellt. Diese ermöglicht es, die Abplatzneigung von Betonrezepturen mittels kleinformatiger Prüfkörper zu analysieren. Abschließend wird unter Anwendung dieser Methode der Einfluss verschiedener Zementarten auf das Abplatzverhalten eines normalfesten Betons untersucht. T2 - STUVA-Tagung 2025 – Internationales Forum für Tunnel und Infrastruktur CY - Hamburg, Germany DA - 25.11.2025 KW - Explosionsartiges Abplatzen KW - Brandfall KW - Klinkereffiziente Zemente PY - 2025 SN - 978-3-96892-327-7 SP - 437 EP - 444 AN - OPUS4-65685 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker A1 - Geburtig, Anja A1 - Trubiroha, P. T1 - Application of a newly proposed sensor for effective UV-irradiance for the monitoring of both natural and artificial weathering conditions N2 - To improve on the classic radiometric sensor with radiometric measurement [ ] here a new UV-sensor characteristic for effective UV is proposed that no longer applies equal weighting of spectral irradiation into the UV irradiance value but rather aims at approaching a weighting according to a typical spectral sensitivity curve of polymers. This curve resembles the erythema curve of the skin which is the basis of the UV-index. For the use of the sensor it would be desirable to keep it in the artificial weathering device for the complete weathering test (including rain phases) while the same sensor should also be applicable for the monitoring of outdoor weathering exposures. A first application of this kind of weighted measurement and a comparison with radiometric measurements accompanied with polymer ageing results will be presented together with conclusions for a future effective UV irradiance sensor. T2 - 9th European Weathering Symposium CY - Basel, Switzerland DA - 18.09.2019 KW - UV-irradiance PY - 2019 SN - 978-3-9818507-5-8 VL - 19 SP - 293 EP - 306 AN - OPUS4-49154 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker A1 - Barthel, Anne-Kathrin A1 - Geburtig, Anja A1 - Trubiroha, P. ED - Reichert, T. T1 - Low-Temperature Irradiation Experiments for PE, PA, and PC Matrices N2 - In this paper, we demonstrate the effects of radiation exposures of polymeric materials with UV-A 340 nm lamps (ISO 4892-3, Type 1A) at -10 °C in comparison to an irradiation at +50 °C using a Global UV Test 200 fluorescent lamp device from Weiss Umwelttechnik GmbH, which incorporates an active cooling appliance. While the effects at -10 °C actually are lower than at + 50°C their extent was clearly beyond expectations. T2 - 8th European Weathering Symposium CY - Vienna, Austria DA - 20.09.2017 KW - Artificial weathering KW - Irradiation KW - Low-temperature KW - Photo-oxidation KW - Polyamide KW - Polycarbonate KW - Polyethylene PY - 2017 SN - 978-3-9818507-1-0 VL - 18 SP - Paper 22, 319 EP - 329 PB - Thomas Würtz Grafik Design CY - Karlsruhe AN - OPUS4-42130 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Trubiroha, P. A1 - Geburtig, Anja A1 - Wachtendorf, Volker T1 - Messung der Temperatur von bestrahlten Oberflächen-Blechdicke beim BST N2 - Die Grenzen der Oberflächentemperaturen von Proben, die der natürlichen oder einer künstlichen Globalstrahlung ausgesetzt sind, können grob mit sog. Schwarzstandard Thermometern BST oder Weißstandard Thermometern WST ermittelt werden [ 1a) ]. Um einige Mängel der aktuellen Konstruktion zu beseitigen, wird ein neues Konzept dieser Thermometer vorgeschlagen, das sie weniger träge und ihre physikalischen Eigenschaften ähnlicher denen einer 5 mm dicken Polymerplatte macht. Es wird auch gezeigt, dass eine Anforderung an die Reaktionszeit von weniger als 1 min in EN 513 unrealistisch ist. T2 - 45. Jahrestagung der GUS CY - Stutensee DA - 16.03.2016 KW - Oberflächentemperatur KW - Strahlungserwärmung KW - IR-Thermometer PY - 2016 SN - 978-3-9816286-7-8 SP - 125 EP - 134 AN - OPUS4-36916 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sitte, M. A1 - Geburtig, Anja T1 - Einfluss der Trocknungszeit nach Feuchtelagerung beim Wellpappen-Berstversuch N2 - Es ist bekannt, dass Wellpappe als meistgenutztes Material für Gefahrgutverpackungen wesentliche Schwächen unter feuchten bzw. nassen Bedingungen zeigt. Verlässliche quantifizierbare Daten hierzu sind leider Mangelware. Obwohl das Material für den weltweiten Versand verwendet wird, werden die Zulassungsprüfungen, v.a. aus Gründen der Reproduzierbarkeit, bei Normklima durchgeführt. Der Berstdruck als wesentliche Größe zur Materialspezifikation wird in Abhängigkeit seiner Vorgeschichte untersucht. Es werden Zeitverlauf und Reversibilität des Berstdruckes nach feuchter Konditionierung für verschiedene Wellpappen-Typen gezeigt. Vorgestellt wird ein Aufbau zur Kopplung des Box-Compression-Tests als Bauteiltest an verschieden feuchte Klimata. T2 - 45. Jahrestagung der GUS CY - Stutensee, Germany DA - 16.03.2016 KW - Feuchtdiffusion KW - Konditionierungsdauer KW - Berstversuch PY - 2016 SN - 978-3-9816286-7-8 SP - 239 EP - 244 AN - OPUS4-36917 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Wachtendorf, Volker A1 - Trubiroha, P. T1 - Quantitative Auswertemöglichkeiten bei der spektralen Bestrahlung – Berechnung des Wirkungsspektrums N2 - Für die Bewertung des Wellenlängeneinflusses auf die Alterungsvorgänge bei der Bestrahlung UV- oder lichtempfindlicher Materialien kann die Methode der spektralen Bestrahlung angewendet werden. Im Prinzip wird dabei das linear dispergierte Spektrum einer Strahlenquelle mit kontinuierlichem Spektrum (z.B. Xe-Lampe) auf eine Probenoberfläche abgebildet, so dass Ort einer Materialänderung und Wellenlänge der Bestrahlung einander zugeordnet werden können. Nachfolgende lokal-auflösende Analysemethoden ermitteln eine Eigenschaftsänderung an einem spezifischen Ort der Probe, aus dem sich dann die Bestrahlungswellenlänge ergibt. Der verwendete Aufbau wird beschrieben. Es wird an einem ausgewählten Beispiel gezeigt, wie durch geeignete Anbindung eines Messsystems zur Bestimmung der spektralen Bestrahlungsstärke und ortsaufgelöste Messungen der Eigenschaftsänderungen eine quantitative Auswertung realisiert werden kann. Der Einfluss nichtlinearer Alterungsverläufe wird diskutiert. Grenzen der Methode werden aufgezeigt und Erweiterungsmöglichkeiten dargestellt. T2 - 46. Jahrestagung der GUS CY - Stutensee-Blankenloch, Germany DA - 22.03.2017 KW - Bewitterung KW - Spektrale Bestrahlung KW - Kunststoffe PY - 2017 SN - 978-3-9816286-9-2 SP - 91 EP - 99 AN - OPUS4-39595 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Homberg, U. A1 - Baum, D. A1 - Prohaska, S. A1 - Kalbe, Ute A1 - Witt, K. J. T1 - Automatic extraction and analysis of realistic pore structures from muCT data for pore space characterization of graded soil N2 - We present image-based methods to extract and analyze the pore structure of graded soil from CT scans. To assess and characterize realistic pore structures of graded soil, we process data of hetero disperse granulär material acquired via high-resolut ion CT. Real soil material configures a pore space with irregulär formations and complex arrangements. In Order to derive parameters of the pore space, a compact representation of the complex pore structure and efficient analysis methods are required. For this purpose, we propose mathematical definitions of the pore structure elements like pore centers, pore paths, pore constrictions, and pore bodies. These definitions are based on the distance map given on the Segmentation of the soil material into particles andpore space. For the extraction of the deftned structure elements, we present two image-basedprocessing pipelines that use the correspondence between our distance-based definition of pore structure elements and a Voronoi decomposition of the pore space. From the extractedpore centers andpore paths, we construct a graph and encode the distance Information on it. This graph, which we call the pore graph, is a compact 3d-representation of the topology of the pore space and provides a good basis to apply efficient graph-based methods for quantification as well as visualization and exploration of the spatial relationships and Connectivity of the pore space. T2 - ICSE6 - 6th International conference on scour and erosion CY - Paris, France DA - 27.08.2012 KW - Microtomography KW - Image analysis KW - Pore structure KW - Pore constriction KW - Suffosion KW - Graded soil PY - 2012 IS - ICSE6-181 SP - 345 EP - 352 AN - OPUS4-26965 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute A1 - Krüger, Oliver A1 - Berger, Wolfgang A1 - Wachtendorf, Volker A1 - Hally, S. ED - Arm, M. ED - Vandecasteele, C. ED - Heynen, J. ED - Suer, P. ED - Lind, B. T1 - Development of leaching procedures for synthetic turf systems N2 - Scrap tyres are widely reused in the form of granules as infill materials or component of sub-base layers in construction of sporting grounds such as synthetic turf areas and athletic track surfaces. The recycled rubber may contain organic and inorganic pollutants due to the presence of vulcanisation catalysts, stabilisers and other additives which can be released into soil and groundwater in the case of outdoor sports facilities. In order to evaluate the amount of potentially mobile pollutants, leaching tests can be employed. This study aimed particularly at the investigation of the feasibility of column tests using complete synthetic surface flooring or turf system assemblies. The release of zinc and polycyclic aromatic hydrocarbons (PAH) leached from components of sports surfaces containing recycled rubber granules was considered. Additionally, batch tests on coated and uncoated styrene butadiene rubber (SBR) granules aged by artificial weathering were performed to indicate its possible influence on the leaching behaviour of zinc and PAH. The chosen approach of column tests simulating typical complete synthetic sports surface installations has been proven to be feasible and robust. The time-dependent leaching behaviour and interactions between single components can be evaluated by column tests. Zinc was the most relevant contaminant in the eluates and its leachability was enhanced after accelerated ageing by artificial weathering. Leachable PAH were found in relatively low but well detectable amounts which increase by ageing as well. T2 - WASCON 2012 CY - Gothenburg, Sweden DA - 30.05.2012 KW - Waste rubber KW - Artificial turf KW - Leaching behaviour KW - Batch test KW - Column test PY - 2012 SP - 1 EP - 5 PB - ISCOWA and SGI AN - OPUS4-26968 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Köppe, Enrico A1 - Bartholmai, Matthias A1 - Liers, A. A1 - Schiller, J. T1 - Radio-based multi-sensor system for person tracking and indoor positioning N2 - Sensor based person tracking is a challenging topic. The main objective is positioning in areas without GPS connection, i.e. indoors. A research project is carried out at BAM, Federal Institute for Materials Research and Testing, to develop and to validate a multi-sensor system for 3D localization. It combines body motion sensing and a guard system for the tracking and recording of the status of persons. The so named BodyGuard system was designed for sensor-based monitoring and radio-based transmission of the movement of a person. Algorithms were developed to transform the sensor data into a spatial coordinate. Thispaper describes how the BodyGuard system operates, which main components were used in the system, how the individual sensor data are converted into 3D motion data, with which algorithms the individual sensors are processed, how individual errors are compensated and how the sensor data are merged into a 3D Model. Final objective of the BodyGuard system is to determine the exact location of a person in a building, e.g. during fire-fighting operations. T2 - WPNC '12 - 9th Workshop on positioning, navigation and communication 2012 CY - Dresden, Germany DA - 15.03.2012 KW - Wireless sensor network (WSN) KW - Embedded systems KW - Sensor calibration and validation KW - Person tracking KW - Inertial navigation system KW - Inertial measurement unit PY - 2012 IS - PS 11 SP - 1 EP - 7 CY - Dresden AN - OPUS4-26028 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jaunich, Matthias A1 - Stark, Wolfgang A1 - Wolff, Dietmar T1 - Low temperature - For a seal this depends on the applied material T1 - Tieftemperatur - Bei Dichtungen entscheidet dies der eingesetzte Werkstoff N2 - For many sealing applications rubbers are applied due to their special material properties and easy use. In many applications as e.g. in aviation, traffic or process technology the material can be exposed to low temperatures during Operation. Therefore it is important to know the material behavior at those low temperatures to determine the temperature ränge that allows a safe Operation of the seal. One of our main Interests is to ensure the safe enclosureof dangerous goods under various conditions such as different temperatures and over long periods of time. For low temperatures the seal function of an elastomer is limited by the rubber-glass transition during which the material properties change from rubber-like to stiff and glass-like. For a given application this correlation is not trivial, as the glass-rubber transition covers a broad temperatureregion and is strongly influenced by the applied loading frequency. Therefore the applicability of a seal material has to be assessed by its properties in relation to the application conditions and the necessary level of tightness. To characterize the material and the seal function thermal analysis (Differential Scanning Calorimetry (DSC) and Dynamic Mechanical Analysis (DMA)), a modlfied method for the accelerated determination of compression set and component tests were applied to different rubber classes, The results show that the temperature ränge where the compression set values come close to 100 % correlates well with the onset temperature of the storage modulus measured by DMA ata measurement frequency of 1 Hz. An in depth analysis of the compression set data allows an estimation of the expected time- and temperature-dependent recovery behavior. T2 - DKT 2012 - German Rubber Conference CY - Nuremberg, Germany DA - 02.07.2012 PY - 2012 IS - 10-2330_5-L-1530 SP - 1 EP - 4 PB - Deutsche Kautschuk-Gesellschaft CY - Frankfurt am Main AN - OPUS4-26190 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - INPR A1 - Battistella, Beatrice A1 - Revill, Adam A1 - Venzago, Cornel A1 - Hoffmann, Volker A1 - Agudo Jácome, Leonardo A1 - Al-Sabbagh, Dominik A1 - Recknagel, Sebastian A1 - Abad Andrade, Carlos Enrique T1 - Depth-Resolved Lithium Isotope Fractionation as a Diagnostic of Interphase Evolution and Degradation in Lithium Ion Batteries N2 - Lithium isotopic fractionation is well-established in dynamic geochemical systems; however, its role in lithium-ion batteries (LIBs) remains uninvestigated. Herein, we report the first depth-resolved demonstration that isotopic separation occurs during Li-ion cell operation whose magnitude depends on the cycling history. Using depth-resolved glow discharge mass spectrometry, we monitored the 7Li/6Li ratio in LiNi0.333Mn0.333Co0.333O2 (NMC111)||graphite coin cell electrodes at defined life-cycle stages. Different charging rates were examined to get mechanistic insight into kinetic and thermodynamic control in the fractionation process. Although pristine electrodes exhibit a uniform isotopic ratio, cycled electrodes show a distinct 7Li enrichment in the positive electrode and a corresponding accumulation of 6Li at the surface of the negative electrode. The degree of isotopic separation varies with the charging rate. Isotopic signatures correlate with capacity fading, indicating lithium isotope mapping as a sensitive diagnostic tool for tracking electrode degradation and the evolution of the electrode–electrolyte interphases in LIBs. KW - Li-ion batteries KW - Lithium isotopes KW - Post-mortem analysis KW - GD-MS KW - Depth profile KW - Mass spectrometry PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-651287 DO - https://doi.org/10.26434/chemrxiv-2025-5rvlk SP - 1 EP - 19 AN - OPUS4-65128 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Häcker, Ralf T1 - Ermittlung der Unsicherheiten in der Werkstoffprüfung N2 - Einschränkung der Werkstoffprüfung. Stand und Entwicklungen hinsichtlich der Messunsicherheit Ein konkretes, einfaches Beispiel zum Zugversuch • Modellunsicherheit • Verfahrensunsicherheit T2 - 266. PTB-Seminar CY - Berlin, Deutschland DA - 20.03.2012 KW - Messunsicherheit KW - Werkstoffprüfung KW - Zugversuch PY - 2012 SP - 1 EP - 27 CY - Berlin AN - OPUS4-25736 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gravenkamp, Hauke A1 - Song, C. A1 - Prager, Jens T1 - Numerische Berechnung der Dispersionseigenschaften von Lambwellen in Platten mit beliebiger Materialzusammensetzung N2 - Für alle Anwendungen geführter Wellen, beispielsweise in der zerstörungsfreien Materialprüfung, ist die exakte und effiziente Berechnung von Dispersionseigenschaften erforderlich. Dabei müssen für eine gegebene Frequenz die Anzahl der ausbreitungsfähigen Moden und deren Wellenzahlen sowie Phasen- und Gruppengeschwindigkeiten berechnet werden. Für den Fall von Lambwellen in homogenen isotropen Platten existieren analytische Gleichungen für die Wellenzahlen, die sich mit numerischen Nullstellensuchverfahren lösen lassen. Für komplexere Strukturen oder dreidimensionale, nicht rotationssymmetrische Wellenleiter ist die Entwicklung numerischer Methoden erforderlich. In der vorliegenden Arbeit wird ein numerisches Verfahren, basierend auf der Scaled Boundary Finite Element Method (SBFEM) [1] vorgestellt. Mit diesem lassen sich Dispersionseigenschaften von beliebigen Wellenleitern sehr effizient berechnen. Ergebnisse werden für den Fall von Wellen in Platten mit komplexer Materialzusammensetzung präsentiert. T2 - DAGA 2012 - 38. Jahrestagung für Akustik - Fortschritte der Akustik CY - Darmstadt, Deutschland DA - 19.03.2012 KW - Ultraschall KW - Lambwellen KW - Dispersion KW - Scaled boundary finite element method PY - 2012 SP - 1 EP - 2 PB - Deutsche Gesellschaft für Akustik e.V. AN - OPUS4-25978 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Altmann, Korinna A1 - Abusafia, A A1 - Bannick, C-G A1 - Braun, U A1 - Crasselt, Claudia A1 - Dittmar, S A1 - Fuchs, M A1 - Gehde, M A1 - Hagendorf, C A1 - Heller, C A1 - Herper, D A1 - Heymann, S A1 - Kerndorff, A A1 - Knefel, M A1 - Jekel, M A1 - Lelonek, M A1 - Lunkenbein, T A1 - Obermaier, N A1 - Manhart, M A1 - Meurer, Maren A1 - Miclea, P-T A1 - Paul, A A1 - Richter, S A1 - Ricking, M A1 - Rohner, C A1 - Ruhl, A A1 - Sakai, Y A1 - Saravia Arzabe, C A1 - Scheid, C A1 - Schmitt, M A1 - Schnarr, M A1 - Schwertfirm, F A1 - Steinmetz, H A1 - Wander, Lukas A1 - Wiesner, Yosri A1 - Zechmeister, L T1 - RUSEKU - Repräsentative Untersuchungsstrategien für ein integratives Systemverständnis von spezifischen Einträgen von Kunststoffen in die Umwelt : Abschlussbericht N2 - Im Verbundprojekt RUSEKU wurde die Probenahme von Wasserproben entscheidend weiterentwickelt. Wichtig ist hierbei zu gewährleisten, dass genügend Merkmalsträger in jeder Probe untersucht werden. Es muss daher eine für den Probenahmeort repräsentative Beprobung hinsichtlich des Wasservolumens in Abhängigkeit der Partikelanzahl gewährleistet sein. Das Hauptaugenmerk lag im vorliegenden Projekt auf einer praxisnahen Beprobungsstrategie. Es wurden verschiedene Konzepte ausprobiert. • Grundsätzlich hat sich gezeigt, dass eine Stichprobe eine Momentaufnahme des MP-Massengehaltes zeigt. Es wird eine hohe Statistik, also eine Vielzahl an Messungen am gleichen Probenahmeort, benötigt, um eine valide Aussage über den MP-Gehalt zu machen. • Es zeigt sich, dass eine integrale Probenahme über mehrere Wochen mit dem SK routinemäßig möglich ist. Die erfassten MP-Massen sind reproduzierbar und robust. • Die DFZ ist für Stichproben geeignet. Partikel < 50 µm werden eventuell unterschätzt • Die fraktionierte Filtration kann für Stich- und Mischproben direkt im Feld genutzt werden. Fraktionen von 10 und 5 µm werden später im Labor Vakuum filtriert. Es erfolgt eine Fraktionierung der Probe mit Siebmaschenweiten von 1000, 500, 100, 50, 10 und 5 µm. • Die fraktionierte Filtration kann auch anschließend an die Beprobung mit dem SK zur Anwendung kommen. Wird die mit dem SK gewonnene Wasserprobe fraktioniert filtriert, kann neben einem MP-Gesamtgehalt auch eine Einschätzung über die Partikelgrößen gewonnen werden. • Für Wässer mit geringen Partikelzahlen wurde ein Messfiltertiegel entwickelt. Dieser hat eine Maschenweite von 6 µm. Seine Anwendung kann mögliche Verluste beim Transferieren vom Probenahmetool zum Messgefäß und mögliche Kontaminationen reduzieren. Die Optimierung der Probenahmestrategie wurde durch Modellversuche und Simulationen unterstützt. Modellversuche zum Sinkverhalten und Simulationen von MP in realen Gewässern verdeutlichten das komplexe Verhalten der Partikel. Es konnte gezeigt werden, dass Partikel ab einer bestimmten Größe (und kleiner) bei genügend starker Turbulenz sich in der Wassersäule unabhängig von ihrer Dichte verhalten und so auch MP mit kleiner Dichte (z.B. PE) in der gesamten Wassersäule zu finden sind. Es konnte mit dem TEM die Existenz von NP gezeigt werden. Ein wesentlicher Aspekt des RUSEKU Projektes war die Beprobung realer Kompartimente. Beprobt wurde neben Oberflächengewässern, das urbane Abwassersystem der Stadt Kaiserslautern, Waschmaschinenabwasser und Flaschenwasser. • In Oberflächengewässern wurde hauptsächlich PE gefunden. Je nach Probe und Gewässer konnten auch PP, PS, PET, PA, SBR und Acrylate nachgewiesen werden. • Im urbanen Abwassersystem der Stadt Kaiserslautern konnte an allen Probenahmestandorten MP nachgewiesen werden. Es wurde hauptsächlich PE, neben geringeren Mengen an PP, PS und SBR gefunden. Nach einem Regenereignis war der SBR Anteil deutlich erhöht. • Die Beprobung eines realen Wäschepostens, bestehend aus T-Shirts und Hemden mit PA/CO oder PES/CO Mischgewebe, zeigte einen PA- und PES-Austrag im Waschwasser. Der überwiegende Teil der detektierten Fasern ist aber auf Baumwolle zurückzuführen. Reine gravimetrische Messungen zur Detektion von MP führen zu einer starken Überschätzung. • In Flaschenwasser (PET-Flaschen) konnte MP detektiert werden. PET wurde nur im stillen Mineralwasser, nicht in Mineralwasser mit Kohlensäure gefunden werden. Teilweise wurde auch das MP-Material des Verschlusses im Wasser detektiert. • Für Luftproben konnte ein Aufbau zur größenselektiven Beprobung getestet werden. Neben der Probenahme hat das Projekt auch gezeigt, dass die TED-GC/MS geeignet für die MP-Detektion im Routinebetrieb ist. Die TED-GC/MS konnte weiter optimiert werden. Es wurden MP-Massen bestimmt. Im Projekt wurden erste realitätsnahe Referenzmaterialien für die MP Detektion hergestellt. Die Herstellung von realitätsnahen Polymeren in ausreichender Homogenität und Menge hat sich als große Herausforderung herausgestellt. KW - Mikroplastik KW - Probennahme KW - TED-GC/MS KW - Fraktionierte Filtration KW - Mikroplastikreferenzmaterial PY - 2022 SP - 1 EP - 201 AN - OPUS4-57800 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Smales, Glen Jacob A1 - Pauw, Brian Richard T1 - DACHS/MOFs/AutoMOFs_4/Synthesis N2 - The DACHS (Database for Automation, Characterization and Holistic Synthesis) project aims to create completely traceable experimental data, covering syntheses, measurements, analyses, and interpretations. DACHS_MOFs focuses on the synthesis and characterisation of metal-organic frameworks, across multiple, automation-assisted experimental series (AutoMOFs), with the overall goal of producing reproducible MOF samples through tracking of the synthesis parameters. DACHS_MOFs is simultaneously used to test the DACHS principles. This upload contain synthesis data from AutoMOFs_4 in HDF5 format (.h5). Each .h5 file contains detailed information on the chemical, experimenal, and synthesis parameters used during the synthesis of a single AutoMOF sample. KW - Automation KW - Procedure KW - Synthesis KW - Traceability PY - 2024 DO - https://doi.org/10.5281/zenodo.11237899 PB - Zenodo CY - Geneva AN - OPUS4-61343 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Smales, Glen Jacob A1 - Pauw, Brian Richard T1 - DACHS/MOFs/AutoMOFs_1/Synthesis N2 - The DACHS (Database for Automation, Characterization and Holistic Synthesis) project aims to create completely traceable experimental data, covering syntheses, measurements, analyses, and interpretations. DACHS_MOFs focuses on the synthesis and characterisation of metal-organic frameworks, across multiple, automation-assisted experimental series (AutoMOFs), with the overall goal of producing reproducible MOF samples through tracking of the synthesis parameters. DACHS_MOFs is simultaneously used to test the DACHS principles. This upload contain synthesis data from AutoMOFs_1 in HDF5 format (.h5). Each .h5 file contains detailed information on the chemical, experimenal, and synthesis parameters used during the synthesis of a single AutoMOF sample. KW - Synthesis KW - Automation KW - Traceability KW - Procedure PY - 2024 DO - https://doi.org/10.5281/zenodo.11236031 PB - Zenodo CY - Geneva AN - OPUS4-60243 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Pauw, Brian Richard A1 - Smales, Glen Jacob A1 - Hörmann, Anja A1 - Moeez, Abdul A1 - Breßler, Ingo T1 - BAMresearch/HDF5Translator: A Framework for translating and transforming data between HDF5 files N2 - HDF5Translator is a Python framework for translating and transforming data between HDF5 files. It supports operations like unit conversion, dimensionality adjustments, and subtree copying, making it suitable for managing and manipulating a wide range of scientific datasets. KW - Measurement data conversion KW - Data conversion KW - HDF5 KW - NeXus KW - NXsas KW - Framework KW - Python KW - Methodology PY - 2024 DO - https://doi.org/10.5281/zenodo.10927639 PB - Zenodo CY - Geneva AN - OPUS4-59797 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Pauw, Brian Richard A1 - Laskina, Sofya A1 - Naik, Aakash A1 - Smales, Glen Jacob A1 - George, Janine A1 - Breßler, Ingo A1 - Benner, Philipp T1 - Jupyter notebook and VASP calculation details accompanying the manuscript: "Ultima Ratio: Simulating wide-range X-ray scattering and diffraction" N2 - Summary: This notebook and associated datasets (including VASP details) accompany a manuscript available on the ArXiv (https://doi.org/10.48550/arXiv.2303.13435) and hopefully soon in a journal as short communication as well. Most of the details needed to understand this notebook are explained in that paper with the same title as above. For convenience, the abstract is repeated here: Paper abstract: We demonstrate a strategy for simulating wide-range X-ray scattering patterns, which spans the small- and wide scattering angles as well as the scattering angles typically used for Pair Distribution Function (PDF) analysis. Such simulated patterns can be used to test holistic analysis models, and, since the diffraction intensity is presented coupled to the scattering intensity, may offer a novel pathway for determining the degree of crystallinity. The "Ultima Ratio" strategy is demonstrated on a 64-nm Metal Organic Framework (MOF) particle, calculated from $Q<0.01$\,$\mathrm{nm}^{-1}$ up to $Q\approx150$\,$\mathrm{nm}^{-1}$, with a resolution of 0.16\,\AA. The computations exploit a modified 3D Fast Fourier Transform (3D-FFT), whose modifications enable the transformations of matrices at least up to $8000^3$ voxels in size. Multiple of these modified 3D-FFTs are combined to improve the low-$Q$ behaviour. The resulting curve is compared to a wide-range scattering pattern measured on a polydisperse MOF powder. While computationally intensive, the approach is expected to be useful for simulating scattering from a wide range of realistic, complex structures, from (poly-)crystalline particles to hierarchical, multicomponent structures such as viruses and catalysts. KW - X-ray KW - Simulation KW - Scattering KW - MOUSE KW - Nanomaterials KW - XRD KW - SAXS KW - PDF KW - Total scattering KW - 3D Fourier transform KW - High resolution KW - FFT PY - 2023 DO - https://doi.org/10.5281/zenodo.7764044 PB - Zenodo CY - Geneva AN - OPUS4-57207 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Graf, Benjamin A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael T1 - Laser metal deposition as repair technology for stainless steel and titanium alloys N2 - In a repair process chain, damaged areas or cracks can be removed by milling and subsequently be reconditioned with new material deposition. The use of laser metal deposition has been investigated for this purpose. The material has been deposited into different groove shapes, using both stainless steel and Ti-6Al-4 V. The influence of welding parameters on the microstructure and the heat affected zone has been studied. The parameters have been modified in order to achieve low heat input and consequently low distortion as well as low metallurgical impact. Finally, an evaluation of the opportunities for an automatized repair process is made. T2 - LANE 2012 - Laser Assisted net shape engineering 7 CY - Fürth, Germany DA - 12.11.2012 KW - Laser metal deposition KW - Laser powder cladding KW - Repair welding KW - Ti-6Al-4 V KW - Stainless steel PY - 2012 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-273066 DO - https://doi.org/10.1016/j.phpro.2012.10.051 N1 - Serientitel: Physics Procedia – Series title: Physics Procedia VL - 39 SP - 376 EP - 381 PB - Elsevier B.V. AN - OPUS4-27306 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Friedrich, Jörg Florian A1 - Unger, Wolfgang A1 - Lippitz, Andreas A1 - Koprinarov, Ivaylo A1 - Weidner, Steffen A1 - Kühn, Gerhard ED - Nowack, H. T1 - Wechselwirkungen zwischen plasmamodifizierten Polymeroberflächen und Metallen T2 - 5. Internationale Fachtagung - ND-Plasma-Technologie CY - Duisburg, Deutschland DA - 1997-09-22 PY - 1997 VL - 5 SP - 1(?) EP - 17(?) PB - Print-Service CY - Mülheim AN - OPUS4-6995 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Friedrich, Jörg Florian A1 - Gerstung, Vanessa A1 - Mix, Renate A1 - Kühn, Gerhard A1 - Weidner, Steffen ED - d'Agostino, R. T1 - Pulsed plasma initiated homo- and copolymerisation - molar masses T2 - 16th International Symposium on Plasma Chemistry (ISPC-16) CY - Taormina, Italy DA - 2003-06-22 PY - 2003 IS - CD-ROM PB - Dep. of Chemistry, Univ. CY - Bari AN - OPUS4-2710 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Ralph-Peter A1 - Falkenhagen, Jana A1 - Much, Helmut A1 - Schulz, Günter A1 - Friedrich, Jörg Florian T1 - Beiträge zur Charakterisierung von synthetischen Si-Polymeren durch Kopplung von HPLC-Trennmethoden mit der MALDI-TOF-MS T2 - DFG-Symposium zum Schwerpunktprogramm "Silicium-Chemie" CY - Werfenweng, Österreich DA - 2000-09-27 PY - 2000 AN - OPUS4-2251 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Falkenhagen, Jana A1 - Krüger, Ralph-Peter A1 - Maier, Bärbel A1 - Much, Helmut A1 - Schulz, Günter T1 - Orthogonal two-dimensional chromatography of poly(ethylene oxid) adducts T2 - HPLC '96 CY - San Francisco, CA, USA DA - 1996-06-16 PY - 1996 CY - San Francisco AN - OPUS4-2221 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Wachtendorf, Volker A1 - Falkenhagen, Jana T1 - Combined impact of UV radiation and nitric acid (HNO3) on HDPE jerrycans – comparison of outdoor and lab test N2 - A damaging action of HNO3-55% only occurs in combination with its decomposition into nitrous gases, which can be caused by UV radiation. In a laboratory test, transparent HDPE jerrycans have been exposed to both UV radiation and 55 wt-% nitric acid solution at (41 ± 2)°C, for up to 20 days. For comparison, UV radiant exposure (21 days) and nitric acid exposure (up to 6 weeks) were performed separately, at nearly equal temperatures. The respective damages are compared with FTIR spectroscopy in ATR and HT-gel permeation chromatography (GPC) on a molecular level and with hydraulic internal pressure testing as a component test. For the used jerrycans, relevant oxidation can only be found after the combined exposure. The gradual increase in oxidative damage shows the good reproducibility of the lab exposure. The decomposition of nitric acid into nitrous gases by UV radiation – as well as the jerrycan oxidation – is also observed at lower HNO3 concentration (28 wt- %). Similar results are obtained after outdoor tests. Again, the damage occurs only after combined exposure, in contrast to the exposures to UV only and to HNO3 only, which were conducted in parallel. Outdoor exposures are most readily accepted as they represent possible end-use conditions. However, the reproducibility of these exposures is poor due to the large temporal variations in weather. There are also several safety risks, which is why the number of replicates remains limited. Since the outdoor and lab exposure tests show the same qualitative results, it is appropriate to conduct systematic studies in the laboratory. After 6 days of lab exposure, the oxidation damage is rated as critical, which corresponds to about 1/10 year in Central Europe, according to the UV radiant exposure. It should be noted that this amount can also occur in two sunny weeks. T2 - 24th iapri World Packaging Conference CY - Valencia, Spain DA - 17.06.2024 KW - Ppolyethylene KW - UV exposure KW - Nitric acid KW - Oxidation PY - 2024 VL - 2 SP - 30 EP - 37 PB - ITENE AN - OPUS4-60414 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weidner, Steffen A1 - Falkenhagen, Jana A1 - Friedrich, Jörg Florian A1 - Krüger, Ralph-Peter A1 - Schulz, Günter A1 - Much, Helmut T1 - Liquid Adsorption Chromatography near Critical Conditions of Adsorption coupled with Matrix-assisted Laser/Ionization Mass Spectrometry T2 - 47th ASMS Conference on Mass Spectrometry and Allied Topics CY - Dallas, TX, USA DA - 1999-06-13 PY - 1999 CY - Dallas, Tex AN - OPUS4-2165 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Ralph-Peter A1 - Friedrich, Jörg Florian A1 - Much, Helmut A1 - Schulz, Günter A1 - Falkenhagen, Jana T1 - Zur Charakterisierung von Si-Polymeren durch Kopplung flüssigchromatographischer Arbeitsweisen mit der MALDI-TOF-MS T2 - DFG-Symposium zum Schwerpunktprogramm "Silicium-Chemie" CY - Bielefeld, Deutschland DA - 1999-05-09 PY - 1999 AN - OPUS4-2239 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Friedrich, Jörg Florian A1 - Schulz, Eckhard A1 - Weidner, Steffen A1 - Kühn, Gerhard T1 - Verbesserungen der mechanischen Festigkeiten von Faser-Polymer-Verbundwerkstoffen durch Vorbehandlung der Fasern im Niederdruckplasma T2 - Vortragsbände des 8. Internationalen Techtextil-Symposiums 1997 CY - Frankfurt am Main, Deutschland DA - 1997-05-12 PY - 1997 VL - 8 SP - 1(?) EP - 16(?) PB - Messe Frankfurt CY - Frankfurt am Main AN - OPUS4-7287 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Ralph-Peter A1 - Falkenhagen, Jana A1 - Much, Helmut A1 - Schulz, Günter A1 - Friedrich, Jörg Florian T1 - Beiträge zur Charakterisierung von synthetischen Si-Polymeren durch Kopplung von HPLC-Trennmethoden mit der MALDI-TOF-MS T2 - Incom 2001 - International Symposium on Instrumentalized Analytical Chemistry and Computer Technology CY - Düsseldorf, Deutschland DA - 2001-03-27 PY - 2001 AN - OPUS4-2254 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Ralph-Peter A1 - Falkenhagen, Jana A1 - Much, Helmut A1 - Schulz, Günter A1 - Weidner, Steffen T1 - Charakterisierung von synthetischen Polymeren durch Kopplung flüssigchromato-graphischer Trennmethoden mit der MALDI-TOF-Massenspektrometrie T2 - 1. Berliner Werkstofftag CY - Berlin, Deutschland DA - 1999-09-16 PY - 1999 AN - OPUS4-2242 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Friedrich, Jörg Florian A1 - Wigant, L. A1 - Unger, Wolfgang A1 - Lippitz, Andreas A1 - Weidner, Steffen A1 - Kühn, Gerhard A1 - Geng, Sh. A1 - Erdmann, J. A1 - Gorsler, H.-V. T1 - Plasmavorbehandlungen von Polymeroberflächen T2 - 2. Freiberger Polymertag CY - Freiberg DA - 1995-05-30 PY - 1995 SP - 17 Seiten CY - Freiberg AN - OPUS4-7014 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Friedrich, Jörg Florian A1 - Ghode, Archana A1 - Kühn, Gerhard A1 - Weidner, Steffen A1 - Geng, Shiming A1 - Retzko, Iris A1 - Unger, Wolfgang A1 - Lippitz, Andreas ED - Schindel-Bidinelli, E. T1 - Polymeroberflächenfunktionalisierungen im gepulsten Plasma mit nachfolgender chemischer Behandlung T2 - 14. Internationales Symposium Swissbonding ; 14. Internationaler Kongreß Swiss Bonding ; 14th Swiss Bonding 00 CY - Rapperswil, Schweiz DA - 2000-05-16 PY - 2000 SP - 31 EP - 44 PB - SWIBOTECH GmbH CY - Bülach AN - OPUS4-6980 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Altmann, Korinna T1 - Deliverable 2: Summary report on: The development of pristine SI traceable reference materials for SMPs (0.1 μm - 10 μm) and NPs (< 0.1 μm), representative of partially degraded/naturally aged samples in complex food and environmental matrices, and for realistic polydisperse size distributions and irregular shapes N2 - PlasticTrace aims to address the urgent need for development and harmonisation of methods for the chemical identification, physical characterisation and quantification of released small micro/nanoplastics (SMPs/NPs) in drinking water, food and environmental matrices, as required by the EU’s Circular Economy Action Plan (CEAP). This report describs the characterisation of nanoPP analysed in the PlasticTrace project aiming to develop a reference material. The nanoPP was analysed mainly by light scattering methods. Homogeneity control was done by DLS. KW - Nanoplastics KW - Reference materials PY - 2024 N1 - Project Number 21GRD07: PlasticTrace (Tracing Micro and NanoPlastics in Food and Environment), funded by the European Union SP - 1 EP - 29 PB - European Association of National Metrology Institutes (EURAMET) CY - Braunschweig AN - OPUS4-62299 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Miliūtė, Aistė T1 - Synthesis and phase purity of the negative thermal expansion material ZrV2O7 N2 - This repository contains computational and experimental data for the manuscript titled “Synthesis and phase purity of the negative thermal expansion material ZrV2O7”. KW - NTE KW - Sol-gel KW - Solid-state KW - Ab-initio KW - XRD KW - Raman PY - 2024 DO - https://doi.org/10.5281/zenodo.12688634 PB - Zenodo CY - Geneva AN - OPUS4-61360 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Götschel, S. A1 - Weiser, M. A1 - Maierhofer, Christiane A1 - Richter, Regina ED - Cardone, G. T1 - Data enhancement for active thermography N2 - Pulse thermography is a non-destructive testing method based on infrared imaging of transient thermal patterns. Heating the surface of the structure under test for a short period of time generates a non-stationary temperature distribution and thus a thermal contrast between the defect and the sound material. Due to measurement noise, preprocessing of the experimental data is necessary, before reconstruction algorithms can be applied. We propose a decomposition of the measured temperature into Green's function solutions to eliminate noise. T2 - QIRT 11 - 11th International conference on Quantitative InfraRed Thermography CY - Naples, Italy DA - 11.06.2012 KW - Datenglättung KW - Rekonstruktion PY - 2012 SP - 1 EP - 9 AN - OPUS4-26447 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Linnemann, Konrad A1 - Ballheimer, Viktor A1 - Sterthaus, Jens A1 - Wille, Frank T1 - Methodological aspects for finite element modeling of lid systems for type B(U) transport packages N2 - The regulatory compliance of the containment system is of essential importance for the assessment process of Type B(U) transport packages. The requirements of the IAEA safety standards for transport conditions implies high loading on the containment system. The integrity of the containment system has to be ensured in mechanical and thermal tests. The containment system of German SNF and HLW transport packages usually includes bolted lids with metal gaskets. The finite element (FE) method is recommended for the analysis of lid systems according to the guideline BAM-GGR 012 for assessment of bolted lid and trunnion systems. FE analyses provide more accurate and detailed information about loading and deformation of such kind of structures. The results allow the strength assessment of the lid and bolts as well as the evaluation of relative displacements between the lid and the cask body in the area of the gasket groove. This paper discusses aspects concerning FE simulation of lid systems for Type B(U) packages for the transport of SNF and HLW. The work is based on the experiences of BAM Federal Institute for Materials Research and Testing as the German competent authority for the mechanical design assessment of such kind of packages. The issues considered include modeling strategies, analysis techniques and the interpretation of results. A particular focus of this paper is on the evaluation of the results with regard to FE accuracy, influence of the FE contact formulation and FE modeling techniques to take the metallic gasket into account. T2 - RAMTRANSPORT 2012 - 9th International Conference on the Radioactive Materials Transport and Storage CY - London, UK DA - 22.05.2012 PY - 2012 IS - Paper 2.2 RAM 27 SP - 1 EP - 8 AN - OPUS4-26353 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mizuno, Y. A1 - Lenke, Peter A1 - Krebber, Katerina A1 - Nakamura, K. T1 - Brillouin gain spectrum characterization in POF fabricated by different manufacturers at 1.32 and 1.55 um N2 - The Brillouin gain spectra (BGS) in perfluorinated graded-index polymer optical fibers (PFGl-POFs) are characterized at 1.32 and 1.55 pm. Three kinds of PFGl-POFs with the same core diameter but fabricated by different manufacturers are tested. For all the PFGl-POFs, the Stokes power measured at 1.32 pm is higher than that at 1.55 pm eine to the lower propagation loss, but significant difference in Stokes power is observed among the three. Based on the measurement by optical time-domain reflectometry, we show that the actual Propagation loss of the PFGl-POFs plays a crucial role in observing BGS. T2 - POF 2012 - 21st International conference on plastic optical fibers CY - Atlanta, Georgia, USA DA - 10.09.2012 KW - Brillouin scattering KW - Perfluorinated graded-index polymer optical fiber KW - Optical time-domain reflectometry KW - Nonlinear optics PY - 2012 SP - 96 EP - 99 AN - OPUS4-26742 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weber, Gert A1 - Rethmeier, Michael ED - Kožuh, Z. T1 - Spot welding and weldbonding of high strength steels for lightweight auto body manufacturing N2 - The resistance spot welding procedure is one of the most important joining technique in lightweight car body shell mass production. Especially for newly developed ultra high strength steels (UHSS) and advanced high strength steels (AHSS), this joining technique has more advantages than other thermal and mechanical joining procedures for thin Steel sheets. Additionally, the technique of adhesive bonding and its combination with the technique of resistance spot welding called weldbonding becomes more and more important. The weldbonding affords many advantages, e.g. improved crash performance, fatigue behaviour and corrosion resistance. The main target of the contribution is to show the influence of different joined ultra and advanced high strength steels on the process reliability for both the resistance spot welding process and the weldbonding process. In this connection the influence of surface conditions of the steel sheets, the applied adhesive and the choice of the welding parameters on the process reliability will be studied. The results for the weldbonding procedure are based on different adhesives. Based on the representation of welding current ranges by weldability lobes, Statements concerning the weldbonding process reliability for some special AHSS and UHSS will be given. The mechanical behaviour of spot welded and weldbonded joints for different AHSS and UHSS will be studied. T2 - EUROJOIN 8 - 8th European Conference CY - Pula, Croatia DA - 24.05.2012 KW - Spot welding KW - Weldbonding KW - High strength steels KW - Process reliability KW - Mechanical properties of joints PY - 2012 SN - 978-953-7518-02-8 SP - 633 EP - 643 PB - Croatian Welding Society (CWS) CY - Zagreb AN - OPUS4-26383 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Smales, Glen Jacob A1 - Pauw, Brian Richard T1 - DACHS/MOFs/AutoMOFs_2/Synthesis N2 - The DACHS (Database for Automation, Characterization and Holistic Synthesis) project aims to create completely traceable experimental data, covering syntheses, measurements, analyses, and interpretations. DACHS_MOFs focuses on the synthesis and characterisation of metal-organic frameworks, across multiple, automation-assisted experimental series (AutoMOFs), with the overall goal of producing reproducible MOF samples through tracking of the synthesis parameters. DACHS_MOFs is simultaneously used to test the DACHS principles. This upload contain synthesis data from AutoMOFs_2 in HDF5 format (.h5). Each .h5 file contains detailed information on the chemical, experimenal, and synthesis parameters used during the synthesis of a single AutoMOF sample. KW - Automation KW - Procedure KW - Synthesis KW - Traceability PY - 2024 DO - https://doi.org/10.5281/zenodo.11236074 PB - Zenodo CY - Geneva AN - OPUS4-60611 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Friedrich, Jörg Florian A1 - Unger, Wolfgang A1 - Lippitz, Andreas A1 - Weidner, Steffen A1 - Geng, Sh. A1 - Wigant, L. A1 - Wöll, Ch. A1 - Erdmann, J. A1 - Gorsler, H.-V. T1 - Characterization of plasma-modified organic surfaces by electron spectroscopy, SEIRA, and MALDI-TOF-MS T2 - 6th European Conference on Applications of Surface and Interface Analysis CY - Montreux, Switzerland DA - 1995-10-09 PY - 1995 SP - TC 11 PB - Wiley CY - Chichester AN - OPUS4-7001 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Rita A1 - Kelm, Jürgen A1 - Kretzschmar, Hans-Jürgen A1 - Schulze, Dietmar A1 - Trubiroha, Peter A1 - Weidner, Steffen T1 - Eine neue Klasse von Ozonschutzmitteln - verbesserter Ozonschutz durch teilweisen Einbau in die Polymermatrix T2 - IRC '03 ; International Rubber Conference 2003 ; Internationale Kautschuk-Tagung 2003 CY - Nürnberg, Deutschland DA - 2003-06-30 PY - 2003 SP - 139 EP - 142 PB - DKG, Dt. Kautschuk-Ges. CY - Frankfurt, Main AN - OPUS4-2608 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weidner, Steffen A1 - Kühn, Gerhard A1 - Just, Ulrich A1 - Werthmann, Barbara A1 - Decker, Renate A1 - Schwarz, Bärbel A1 - Borowski, Renate T1 - MALDI/MS - A New Technique in Characterizing Chemical Heterogeneity of Degradation Products of Poly(Ethylene Terephthalate)s T2 - International GPC Symposium '96 CY - San Diego, CA, USA DA - 1996-09-08 PY - 1996 SP - 632 EP - 651 CY - Milford, Mass. AN - OPUS4-11905 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Just, Ulrich A1 - Weidner, Steffen A1 - Wittke, Wolfgang A1 - Friedrich, Jörg Florian A1 - Rittig, F. A1 - Gruber, F. T1 - 2D-Characterization of Polyamides using Chromatography and MALDI-TOF-MS T2 - Waters International GPC 2003 and ISPAC-16-Symposium CY - Baltimore, MD, USA DA - 2003-06-09 PY - 2003 AN - OPUS4-2631 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schulz, Günter A1 - Falkenhagen, Jana A1 - Krüger, Ralph-Peter T1 - Kopplung von HPLC-Trennmethoden mit der MALDI-TOF-Massenspektrometrie zur Charakterisierung von Si-haltigen Verbindungen T2 - DFG-Symposium zum Schwerpunktprogramm "Silicium-Chemie" CY - Werfenweng, Österreich DA - 2002-05-02 PY - 2002 AN - OPUS4-1797 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Ralph-Peter A1 - Falkenhagen, Jana A1 - Gerstung, Vanessa A1 - Much, Helmut A1 - Schulz, Günter A1 - Friedrich, Jörg Florian T1 - Beiträge zur Charakterisierung von synthetischen Si-Polymeren durch Kopplung von HPLC-Trennmethoden mit der MALDI-TOF-Massenspektrometrie T2 - Berliner Polymeren-Tage 2000 CY - Berlin, Deutschland DA - 2000-10-09 PY - 2000 CY - Berlin AN - OPUS4-2252 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -