TY - CONF A1 - Erhard, Anton A1 - Völzke, Holger A1 - Droste, Bernhard A1 - Wolff, Dietmar A1 - Wille, Frank T1 - Nuclear power plant waste management strategy in Germany N2 - The shut-down of eight nuclear power plants and the phase out of the nuclear energy genera� tion in Germany, due to a decision of the German government after the Fukushima accident, has rapidly forced the need for transportation and storage of spent nuclear fuel (SNF) from shut-down reactors in this country. In accordance with the present strategy in Germany, which is characterized by searching for appropriate final repository areas, only the dry interim stor� age facilities are available for storage nuclear waste of the decommissioned plants as well as the operating plants. Therefore, the transportation and the storage casks must be available for both types of light water reactors. But for the time being this is the bottleneck. Unfortunately the prognoses are neglecting the fact, that such a high number of casks are needed in a very short space of time. This requires the acceleration of formal activeness in relation to the li� censes but also an increase of the production. In the meanwhile to get this process started, the only possibility is the storage in the pools at the plant site. Anyway, for the time being, this is one of the problems for dismantling the eight plants which have been shut down due to the decision of the Government, which is now fixed in the last amended German Atomic Energy Act dated 24th of February 2012. Starting to dismantle in the radioactive regions of the plants requires empty pools. For emptying the pools of damaged SNF special procedures regarding the transportation and storage are necessary. The transportation of damaged SNF requires special casks or at least special procedures and therefore also a special licenses. This paper describes the challenge for the management in transportation and storage of SNF in Germany after the shut-down of the nuclear power plants by reason of the Fukushima acci� dent. T2 - PATRAM 2013 - 17th International symposium on the packaging and transportation of radioactive materials CY - San Francisco, CA, USA DA - 18.08.2013 PY - 2013 SP - 1 EP - 11 PB - Omnipress AN - OPUS4-30135 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völzke, Holger A1 - Wolff, Dietmar A1 - Probst, Ulrich A1 - Nagelschmidt, Sven A1 - Schulz, Sebastian T1 - Long-term performance of metal seals for transport and storage casks N2 - Dual purpose casks for the transportation and storage of spent nuclear fuel and other radioactive materials require very high leak-tightness of lid closure Systems under accident conditions as well as in the long-term to prevent activity release. For that purpose metal seals of specific types with an inner helical spring and outer metal liners are widely used and have shown their excellent performance if certain quality assurance requirements for fabrication and assembling are satisfied. Well defined surface roughness, clean and dry inert conditions are therefore essential. No seal failure in a loaded cask happened under these conditions until today. Nevertheless, the considered and licensed Operation period is limited and all safety assessments have been performed and approved for this period of time which is 40 years in Germany so far. But in the meantime longer storage periods might be necessary for the future and therefore additional material data will be required. BAM is involved in the qualification and evaluation procedures of those seals from the early beginning. Because long-term tests are always time consuming BAM has early decided to perform additional tests with specific test seal configurations to gain a better understanding of the long-term behavior with regard to seal pressure force, leakage rate and useable resilience which is safety relevant mainly in case of accidental mechanical loads inside a storage facility or during a subsequent transport. Main test parameters are the material of the outer seal jacket (silver or aluminum) and the temperature. This paper presents the BAM test program including an innovative test mock-up and most recent test results. Based on these data extrapolation models to extended time periods are discussed, and also future plans to continue tests and to investigate seal behavior for additional test parameters are explained. T2 - PATRAM 2013 - 17th International symposium on the packaging and transportation of radioactive materials CY - San Francisco, CA, USA DA - 18.08.2013 PY - 2013 SP - 1 EP - 13 PB - Omnipress AN - OPUS4-30136 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kumano, Y. A1 - Droste, Bernhard A1 - Hirose, M. A1 - Harvey, J. A1 - Reiche, I.. A1 - Wolff, Dietmar A1 - McConnell, P. A1 - Varley, K. T1 - Overview of the IAEA's joint working group on integrated safety case for dual purpose casks N2 - Spent nuclear fuel is generated from the operation of nuclear reactors and needs to be safely managed following its removal from reactor cores. Spent nuclear fuels are usually stored in a reactor pool for a short period of time after defueling, and then they are shipped to its next destination for reprocessing, disposal, or further storage. In some countries, a concept of Dual Purpose Cask (DPC) is considered as an attractive option for further storage. This is because of that the concept increases flexibility for storage capacity, as well as its economic efficiency that can reduce the complexity of handling highly radioactive spent fuels. The management of spent fuel using a DPC involves storage of spent fuel as well as on-site and off-site transportation before and after storage. Most countries require package design approval for the DPC to be transported. In addition, it is required in many countries to have a license for storage of the spent fuel in the DPC or a license for a storage facility that contains DPCs. Therefore, demonstration of compliance of the DPC with national and international transport regulations as well as with the storage requirements is necessary. In June 2010, the IAEA organized “International Conference on Management of Spent Fuel from Nuclear Power Reactors”. In this conference, many countries expressed their interest on harmonizing both transport and storage safety cases for DPCs that has a possibility to establish an effective and integrated regulatory framework in a holistic manner. Taking into account the increasing needs among Member States, the IAEA set up a new working group following the conference to discuss how to develop an integrated safety case for both transportation and storage.This activity is planned to be completed in 2013. Currently, a technical report is being prepared as an outcome of this activity. In this paper, the IAEA’s approach to demonstrate the safety of DPCs in a holistic manner is described first, followed by the overview of the draft document. It also presents the difference between the conventional transport cask concept and the DPC concept. T2 - PATRAM 2013 - 17th International symposium on the packaging and transportation of radioactive materials CY - San Francisco, CA, USA DA - 18.08.2013 PY - 2013 SP - 1 EP - 9 PB - Omnipress AN - OPUS4-30140 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wille, Frank A1 - Wolff, Dietmar A1 - Droste, Bernhard A1 - Völzke, Holger A1 - Baden, M. T1 - German approach and experience feedback of transport ability of SNF packages after interim storage N2 - In Germany the concept of dry interim storage of spent fuel in dual purpose metal casks is implemented, currently for periods of up to 40 years. The casks being used have an approved package design in accordance with the international transport regulations. The license for dry storage is granted on the German Atomic Energy Act with respect to the recently revised “Guidelines for dry interim storage of irradiated fuel assemblies and heat-generating radioactive waste in casks” by the German Waste management Commission (ESK). For transport on public routes between or after long term interim storage periods, it has to be ensured that the transport and storage casks fulfil the specifications of the transport approval or other sufficient properties which satisfy the proofs for the compliance of the safety objectives at that time. In recent years the validation period of transport approval certificates for manufactured, loaded and stored packages were discussed among authorities and applicants. A case dependant system of 3, 5 and 10 years was established. There are consequences for the safety cases in the Package Design Safety Report including evaluation of long term behavior of components and specific operating procedures of the package. Present research and knowledge concerning the long term behavior of transport and storage cask components have to be consulted as well as experiences from interim cask storage operations. Challenges in the safety assessment are e.g. the behavior of aged metal and elastomeric gaskets under IAEA test conditions to ensure that the results of drop tests can be transferred to the compliance of the safety objectives at the time of transport after the interim storage period. T2 - PATRAM 2013 - 17th International symposium on the packaging and transportation of radioactive materials CY - San Francisco, CA, USA DA - 18.08.2013 KW - Storage KW - Transport KW - Lagerung KW - Verpackung KW - Radioactive material PY - 2013 SP - 1 EP - 9 PB - Omnipress AN - OPUS4-30159 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Völzke, Holger A1 - Wolff, Dietmar A1 - Kasparek, Eva Maria T1 - Beitrag zu den Anforderungen an die Beschaffenheit von Endlagerbehältern hinsichtlich ihrer Rückholbarkeit und Bergbarkeit N2 - Die Bundesanstalt für Materialforschung und –prüfung (BAM) wurde von der AG 3 der Kommission Lagerung hoch radioaktiver Abfallstoffe gebeten, Anforderungen an Behälter für die Endlagerung hoch radioaktiver Abfallstoffe im Hinblick auf ih-re Rückholbarkeit während des Endlagerbetriebes und ihre Bergbarkeit nach Ver-schluss des Endlagers über einen Zeitraum von 500 (bis 1.000 ?) Jahren darzu-stellen. Die BAM kommt diesem Wunsch auf der Grundlage ihrer langjährigen Er-fahrungen und Fachkenntnisse auf den Gebieten der Bauartprüfung und der si-cherheitstechnischen Begutachtung von Transport- und Lagerbehältern für radio-aktive Stoffe nach. PY - 2015 UR - https://www.bundestag.de/blob/396206/f0a6276f4e2741c3022afb8ce64c0689/drs_047-data.pdf SP - 1 EP - 12 AN - OPUS4-35104 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völzke, Holger A1 - Wolff, Dietmar A1 - Orellana Pérez, Teresa A1 - Herold, Christian A1 - Bollingerfehr, W. A1 - Wunderlich, A. A1 - Prignitz, S. T1 - Anforderungen an Behälter für die Endlagerung hochradioaktiver Abfälle in Steinsalz, Tonstein und Kristallingestein N2 - Bei der Auswahl eines Standortes für ein Endlager für hochradioaktive Abfälle (Wärme entwickelnde radioaktive Abfälle und ausgediente Brennelemente) in Deutschland werden auf Grundlage des Standortauswahlgesetzes von 2017 die drei potenziellen Wirtsgesteine Steinsalz, Tonstein und Kristallingestein in Betracht gezogen. Die Auswahl eines konkreten Endlagerstandortes steht dabei in engem Zusammenhang mit den für die jeweiligen Wirtsgesteine geeignet erscheinender Endlagersystemen. Zentraler Bestandteil dieser Endlagersysteme sind die Endlagerbehälter, deren Gestaltung und Auslegung maßgeblich die Randbedingungen für die Transport- und Einlagerungstechnik vorgibt und zudem die Nachweise zur Betriebs- und Langzeitsicherheit entscheidend prägt. Daher ist es für die Behälterentwicklung erforderlich, die an Endlagerbehälter zu stellenden Anforderungen systematisch herzuleiten. Auf dieser Grundlage können anforderungsgerechte Endlagerbehälter zielgerichtet für die jeweils zu untersuchenden Endlagerstandorte in unterschiedlichen Wirtsgesteinen entwickelt werden. Dieser Beitrag fasst die wesentlichen Ergebnisse des von BAM und BGE TECHNOLOGY GmbH im Zeitraum 2017 bis 2020 bearbeiteten und vom Bundesministerium für Wirtschaft und Energie (BMWi) geförderten Forschungsvorhabens KoBrA zusammen, die in einem Abschlussbericht und vier zugehörigen Teilberichten umfassend dokumentiert sind. T2 - Tage der Standortauswahl CY - Freiberg, Germany DA - 11.02.2021 KW - Endlager KW - Behälter KW - Sicherheitsanforderungen KW - hochradioaktive Abfälle PY - 2021 SP - 1 EP - 10 AN - OPUS4-53114 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Herold, Christian A1 - Völzke, Holger A1 - Wolff, Dietmar A1 - Orellana Pérez, Teresa A1 - Bollingerfehr, W. A1 - Wunderlich, A. A1 - Prignitz, S. T1 - Herleitung und Zusammenstellung der Anforderungen an Endlagerbehälter für ein HAW-Endlager in den drei potenziellen Wirtsgesteinen Steinsalz, Tonstein und Kristallingestein; Bericht zum Arbeitspaket 3 des FuE Verbundvorhabens KoBrA N2 - Der Bericht zum Arbeitspaket 3 baut auf den Ergebnissen der internationalen Recherche (AP1) sowie der Zusammenstellung der Randbedingungen und Beanspruchungsgrößen für die Endlagerbehälter (AP2) auf. Die Anforderungen an die Behälter – regulatorische, betriebliche sowie solche aus der Standortgeologie und den Einwirkungen und Prozessen, denen die Behälter ausgesetzt sind – werden hergeleitet und systematisch dargestellt. Die für das Endlagersystem zu betrachtenden Nutzungsphasen werden aus den regulatorischen Anforderungen hergeleitet und charakterisiert. Die Einwirkungen auf die Behälter in den drei potenziellen Wirtsgesteinen sowie die sich für die Erfüllung der Sicherheitsfunktionen des Behälters als Teil des Endlagersystems ergebenden Behälterfunktionen werden ebenfalls wirtsgesteins- und zeitphasenabhängig betrachtet. Schließlich werden aus den Einwirkungen auf die Behälter und den Anforderungen an die Behälterfunktionen auch quantifizierbare Behälterfunktionen für alle drei potenziellen Wirtsgesteine abgeleitet. KW - Endlager KW - Behälter KW - Sicherheitsanforderungen KW - Hochradioaktive Abfälle PY - 2020 UR - https://www.bge-technology.de/fileadmin/user_upload/MEDIATHEK/f_e_berichte/KoBrA/2020-KoBrA_Bericht_AP3.pdf N1 - Auftraggeber: Bundesministerium für Wirtschaft und Energie (BMWi), Förderkennzeichen: 02E11527 und 02E11537. SP - 1 EP - 254 PB - BGE Technology CY - Peine AN - OPUS4-53119 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Völzke, Holger A1 - Herold, Christian A1 - Wolff, Dietmar A1 - Orellana Pérez, Teresa A1 - Bollingerfehr, W. A1 - Prignitz, S. A1 - Wunderlich, A. T1 - Abschlussbericht zum FuE-Verbundvorhaben KoBrA: Anforderungen und Konzepte für Behälter zur Endlagerung von Wärme entwickelnden radioaktiven Abfällen und ausgedienten Brennelementen in Steinsalz, Tonstein und Kristallingestein N2 - Im Forschungsvorhaben KoBrA werden Anforderungen an Endlagerbehälter für hochradioaktive Abfälle erstmals systematisch und unter Berücksichtigung des internationalen Standes von Wissenschaft und Technik hergeleitet. Parallel werden die behälterrelevanten Randbedingungen und Beanspruchungsgrößen für Endlagerbehälter in den drei potenziellen Wirtsgesteinen Steinsalz, Tonstein und Kristallingestein ermittelt. Darauf aufbauend werden die zur Erfüllung der Anforderungen unter den gegebenen Einwirkungen und Beanspruchungen notwendigen Behälterfunktionen bestimmt und erste Konzeptideen für zukünftige Endlagerbehälter diskutiert bzw. entwickelt. KW - Endlager KW - Behälter KW - Anforderungen KW - Hochradioaktive Abfälle KW - Wirtsgestein PY - 2020 DO - https://doi.org/10.2314/KXP:1750909669 N1 - Auftraggeber: Bundesministerium für Wirtschaft und Energie (BMWi), Förderkennzeichen: 02E11527 und 02E11537. SP - 1 EP - 110 PB - BGE Technology CY - Peine AN - OPUS4-52289 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Orellana Pérez, Teresa A1 - Völzke, Holger A1 - Wolff, Dietmar A1 - Zencker, Uwe T1 - Relevance of cladding failure mechanisms due to zirconium hydride precipitation under extended dry storage conditions in Germany N2 - The German nuclear waste management strategy consists of dry interim storage of spent fuel inside dual purpose casks and its subsequent direct final disposal in a deep geological repository. Interim storage is limited to 40 years so far, but will have to be extended until repository site selection and operation is concluded, potentially up to 100 years. In this context, research on the long term performance of safety relevant cask components and fuel rod integrity during such extended periods of time is of outmost importance. The barrier function of the fuel cladding depends on its integrity under operational and accidental conditions along with storage and subsequent transportation and is mainly affected over time by altering of the cladding microstructure and by thermo-mechanical conditions during reactor operation and subsequent wet and dry storage. This paper focuses on failure mechanisms regarding cladding embrittlement caused by physical phenomena concerning hydrogen dissolution and precipitation of hydrides in the zirconium matrix. Within this context, potential cladding integrity issues under extended interim storage conditions followed by transportation are emphasized. Delayed hydride cracking (DHC) is a well-known time-dependent temperature-activated phenomenon failure mechanism of the fuel cladding during reactor operation. The phenomenon consists of hydrogen diffusion and hydride precipitation at the tip of an initial crack and the propagation of the crack to an approximate distance equal to the length of the hydride. This failure mechanism is temperature-activated phenomenon and enhances along with thermal cycling of the fuel cladding, e. g. during reactor shutdowns. DHC shows limited relevance under quasi static storage conditions with continuously lowering temperatures. However, the literature points that DHC may occur when the temperature during storage decreases to a certain level after some decades and in combination with stress concentrations in the cladding material. When spent fuel is transferred to dry storage by vacuum drying, the cladding temperature raises up to peak temperatures of ~370°C. Under these conditions, hydrides dissolute into the zirconium matrix up to the solubility limit defined by the peak temperature and this amount of hydrogen can precipitate in a radial re-oriented fashion due to the temperature decrease during storage. Cladding materials with radially precipitated hydrides show significant embrittlement. Radially oriented hydrides are perpendicularly oriented to hoop stresses representing the most critical configuration. Brittle failure of the cladding then occurs by crack propagation through radially oriented hydrides and finally through the zirconium matrix. The susceptibility to radial hydride precipitation depends on cladding material type and microstructure, hydrogen content, pre-drying hydride distribution, irradiation conditions, and temperature and stress histories during drying and storage operations. This paper addresses major considerations concerning spent fuel cladding embrittlement due to hydride precipitation with regard to the boundary conditions of dry spent fuel storage in Germany. Analytical, numerical, and experimental approaches are to be discussed by BAM in order to identify the specific needs for future R&D work in that area with the purpose to provide the necessary data base for proper safety demonstration and evaluation along with future extended storage licensing procedures. T2 - 2017 Water Reactor Fuel Performance Meeting CY - Jeju, Korea DA - 10.09.2017 KW - Cladding KW - Hydride precipitation KW - Spent fuel PY - 2017 SP - 1 EP - 8 AN - OPUS4-44749 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weber, Mike A1 - Zencker, Uwe A1 - Wolff, Dietmar A1 - Völzke, Holger A1 - Herbrich, Uwe A1 - Nagelschmidt, Sven T1 - Numerical analysis of cask accident scenarios in storage facilities N2 - Existing spent nuclear fuel (SF) and high active waste (HAW) management policies and practices worldwide are the result of past presumptions that sufficient reprocessing and/or disposal capacity would be available in the near term. Consequently, in the past many countries have developed specific solutions for different periods of time due to their individual national nuclear policies. In Germany the concept of dry interim storage in dual purpose metal casks before disposal is being pursued for SF and HAW management and transport and storage licenses have been issued accordingly. The current operation licenses for existing storage facilities have been granted for a storage period of up to 40 years. This concept has demonstrated its suitability for over 20 years so far. Relevant safety requirements have been assessed for the short-term as well as for the long-term for site-specific operational and accidental storage conditions. But in the meantime significant delays in the national repository siting procedure occurred which will make extended storage periods necessary in the future. T2 - PATRAM 2013 - 17th International symposium on the packaging and transportation of radioactive materials CY - San Francisco, CA, USA DA - 18.08.2013 KW - Numerical analysis KW - Interim storage KW - Cask accident scenario PY - 2013 SP - Session H, Paper 202, 1 EP - 9 PB - Omnipress AN - OPUS4-30227 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Botsch, W. A1 - Smalian, S. A1 - Hinterding, P. A1 - Völzke, Holger A1 - Wolff, Dietmar A1 - Kasparek, Eva Maria T1 - Dual purpose cask safety evaluation - Expertise in dry storage N2 - In Germany dual purpose casks for spent nuclear fuel (SF) or high level radioactive waste (HLW) are used for safe transportation and interim storage. Key safety issues in both fields are the safe enclosure of the radioactive material, the safe removal of decay heat, securing nuclear criticality safety, limitation of radiation exposure to acceptable levels and keeping it as low as reasonable achievable (ALARA principle). Whereas these safety requirements during transportation are ensured by the Type-B(U)-design testing and approval procedure on basis of internationally agreed IAEA (International Atomic Energy Agency) requirements storage licenses are issued on national and site specific safety analyses. This paper presents experiences from recent interim storage safety evaluation and licensing procedures in Germany on basis of a Type-B(U) certified cask designs concerning specific differences from Operation and accident conditions inside the storage facility. The focus is laid on the interaction of cask and building structures with regard to shielding, heat removal and accident analyses including aircraft crash. Basic safety is assured by thick-walled metal casks with monitored double lid Systems. They also reduce radiation to levels where workers can safely operate and maintain the casks inside the storage facility. The storage building e. g. provides additional shielding and protection against extemal hazards depending on the building construction. In addition, the storage building helps to reduce radiation levels at the boundary of the storage site well below regulatory limits given by the German Radiation Protection Ordinance (StrSchV). T2 - PATRAM 2013 - 17th International symposium on the packaging and transportation of radioactive materials CY - San Francisco, CA, USA DA - 18.08.2013 KW - Dual purpose cask KW - Long-term storage PY - 2013 SP - 1 EP - 8 PB - Omnipress AN - OPUS4-30235 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wolff, Dietmar A1 - Völzke, Holger A1 - Wille, Frank A1 - Droste, Bernhard T1 - Extended storage after long-term storage N2 - Existing spent nuclear fuel (SF) and high active waste (HAW) management policies and practices worldwide are the result of past presumptions that sufficient reprocessing and/or disposal capacity would be available in the near term. Consequently, in the past many countries have developed specific solutions for different periods of time due to their individual national nuclear policies. In Germany the concept of dry interim storage in dual purpose metal casks before disposal is being pursued for SF and HAW management and transport and storage licenses have been issued accordingly. The current operation licenses for existing storage facilities have been granted for a storage period of up to 40 years. This concept has demonstrated its suitability for over 20 years so far. Relevant safety requirements haven been assessed for the short-term as well as for the long-term for site-specific operational and accidental storage conditions. But in the meantime significant delays in the national repository siting procedure occured which will make extended storage periods necessary in the future. This paper describes the current situation in Germany with regard to dry cask storage and focuses on current perspectives considering regulatory, technical, and scientific aspects for storage license renewal. Since there is one case of a storage license limitation to only 20 years due to administrative reasons, first experience is currently gathered in case of an expiring storage license. Subsequent license options have been pursued intensively including the extension of the initial storage license as well as shipping all casks to another storage facility considering an extended storage period at that storage facility as well. All safety relevant aspects have to be reviewed on basis of the current state-of-the-art which might be different from the initial safety demonstrations. That includes new safety assessment standards as well as improved knowledge base. Major issues are e.g. improved accident scenario analyses, assessment methods, and consideration of aging effects from previous operation periods. Inspection programs with respect, e.g. to bolts and seals to verify leak-tightness and lid screw pre-stress have been initiated to demonstrate proper cask conditions for extended storage as well as transportation to another storage facility. T2 - PATRAM 2013 - 17th International symposium on the packaging and transportation of radioactive materials CY - San Francisco, CA, USA DA - 18.08.2013 KW - Extended storage KW - Long-term storage KW - Dual purpose cask PY - 2013 SP - Paper 184, 1 EP - 12 PB - Omnipress AN - OPUS4-30242 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völzke, Holger A1 - Wolff, Dietmar T1 - Update on the German approach of storing spent nuclear fuel in dual purpose casks until final disposal N2 - The German approach of storing spent nuclear fuel in dual purpose casks until final disposal is based on individually licensed storage sites concerning specific nuclear inventories and dual purpose cask types. The currently approved license period is maximum 40 years. With nuclear policy changes including the phase-out decision of 2011 and a new approach for the HLW repository siting process set up 2013 by law also the spent fuel and HLW management strategy has to be adapted. This includes the timely development of disposal container concepts as part of the overall repository siting process and the need for longer interim storage periods until final disposal. Other aspects affect new regulations about the financing of the nuclear waste management by the industry and the public sector, the restructuring of responsible authorities in 2016/2017 and the adaption of R&D funding programs addressing also pre-disposal (or extended interim storage) issues. BAM as a Federal Research Institute has been responsible for or in charge of container safety Evaluation for transport and storage casks for radioactive waste for several decades and started addressing potential Extended interim storage issues already several years ago. This included participation in international projects at the IAEA or in the U.S. Extended Storage Collaboration Program (ESCP) as well as long term laboratory tests with metal seals, elastomeric seals and polymers for neutron shielding purposes. Test results of BAM are published regularly and gained data provide valuable information about thermo-mechanical and radiological degradation effects as well as the long term Performance of respective cask components. Regarding the reliable extrapolation and prediction of the long term Performance of cask materials and components for time periods of up to 80 or even 100 years the continuation and extension of laboratory tests and the development of analytical and numerical simulation models and tools is essential and under way. T2 - 16th International High -Level Radioactive Waste Management Conference (IHLRWM 2017) CY - Charlotte, NC, USA DA - 09.04.2017 KW - Spent fuel KW - Storage KW - Cask KW - Safety KW - Disposal PY - 2017 SP - 189 EP - 194 AN - OPUS4-40411 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Orellana Pérez, Teresa A1 - Völzke, Holger A1 - Wolff, Dietmar A1 - Zencker, Uwe T1 - Cladding considerations at BAM regarding extended storage spent fuel N2 - With the clear expectation of the need for extending spent fuel storage in Germany beyond the initial license period of maximum 40 years additional material data and knowledge about the long term performance and integrity of casks and internals like fuel rods will be required to meet major safety goals and regulatory requirements. Based on a broad knowledge base about fuel cladding behavior, degradation mechanisms and related potential failure mechanisms, e. g. induced by reoriented Hydride precipitation, as illustrated in this paper, a specific gap analyses for the German situation regarding fuel conditions and cladding materials should identify the specific knowledge gaps to be addressed and closed in the near future. This is of specific interest as all spent fuel assemblies are going to be transferred to dry cask storage with the next decade and as a consequence of the German nuclear phase-out decision. Within several decades, BAM as a Federal materials research institute gathered a broad range of expertise in the safety evaluation of materials, components and casks under operational and accidental thermal and mechanical conditions. This paper elucidates selected Basic considerations regarding technical and scientific knowledge about the long term aging performance and potential failure mechanisms of fuel cladding materials. Under consideration of the national R&D funding policy which has been adapted to the extended interim storage or pre-disposal needs and the competences of BAM, its future R&D strategy is explained and some R&D objectives have already been identified. BAM will continue and expand ist engagement in the area of investigating fuel cladding material behavior in the long term and developing validated simulation and analyses tools in collaboration with national and international partners. R&D outcomes shall improve the knowledge-base to close identified knowledge gaps in the area of demonstrating fuel cladding integrity and to provide crucial information with regard to future safety assessments for the extended interim spent fuel storage. T2 - 16th International High -Level Radioactive Waste Management Conference (IHLRWM 2017) CY - Charlotte, NC, USA DA - 09.04.2017 KW - Spent fuel KW - Storage KW - Fuel cladding PY - 2017 SP - 718 EP - 725 AN - OPUS4-40412 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Probst, Ulrich A1 - Hagenow, Peter A1 - Völzke, Holger A1 - Wolff, Dietmar A1 - Wossidlo, Peter A1 - Abbasi, Behboud A1 - Achelpöhler-Schulte, Andreas A1 - Schulz, Sebastian T1 - Investigation of seal effects according to axial compression variation of metal seals for transport and storage casks T2 - PATRAM 2007, 15th International Symposium on the Packaging and Transportation of Radioactive Materials CY - Miami, Florida, USA DA - 2007-10-21 KW - Metal Seals KW - Axial Compression KW - Cycling Tests KW - Helium Leakage Rate PY - 2007 SP - 1 EP - 8 PB - Institute of Nuclear Materials Management AN - OPUS4-17542 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -