TY - CONF A1 - Kotsifaki, D.G. A1 - Zekou, L. A1 - Pentzien, Simone A1 - Krüger, Jörg A1 - Serafetinides, A.A. ED - Saunders, D. ED - Strlic, M. ED - Korenberg, C. ED - Luxford, N. ED - Birkhölzer, K. T1 - Cleaning of artificially soiled papers by infrared and mid-infrared lasers N2 - One of the most important materials presenting and witnessing human culture is paper. The cleaning of paper is often necessary because contamination must be removed so that the fragile organic substrate can be preserved. The conventional cleaning methods are mechanical or involve the application of chemicals. These methods can damage drawings or print layers to some extent or make the original paper substrate brittle. More specifically, the use of a scalpel blade can cause damage to fibers. Chemical cleaning is difficult to perform locally, can dissolve foreign matter that then migrates into the paper substrate, or involves volatile organic compounds that can be harmful to the conservator. There is, therefore, a need for new conservation technologies aimed at the safe cleaning of paper. Lasers have proved to be an appropriate tool for cleaning as the energy dose and penetration depth at the specific point of contamination can be controlled. Additionally, if used properly, laser cleaning is not destructive to the paper. T2 - LACONA IX - Lasers in the conservation of artworks CY - London, UK DA - 07.09.2011 KW - Laser cleaning KW - Paper KW - Artificial soiling KW - Nanosecond laser KW - Microsecond laser PY - 2013 SN - 978-1-904982-87-6 SP - 219 EP - 221 PB - Archetype publications Ltd. AN - OPUS4-27956 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pfennig, Anja A1 - Linke, B. A1 - Schulze, S. A1 - Kranzmann, Axel T1 - Corrosion in pipe steels exposed to supercritical CO2 during carbon capture and storage CCS N2 - The CCS technique involves the compression of emission gasses in deep geological layers. To guarantee the safety of the site, CO2-corrosion of the injection pipe steels has to be given special attention when engineering CCS-sites. To get to know the corrosion behaviour samples of the heat treated steel 1.72252CrMo4, used for casing, and the stainless injection-pipe steel 1.4034 X46Cr13 were kept at T=60 °C and ambient pressure as well as p=100 bar for 700 h - 8000 h in a CC 2-saturated synthetic aquifer environment similar to possible geological on-shore CCS-sites in the northern German Basin. The isothermal corrosion behaviour obtained by mass gain of the steels in the gas phase, the liquid phase and the intermediate phase gives surface corrosion rates around 0.1 to 0.8 mm/year at ambient pressure and much lower about 0.02 to 0.2 mm/year at 100 bar where the CO 2 is in its supercritical state. Severe pit corrosion with pit heights around 4.5 mm are only located on the 42CrMo4 steel. Main phase of the continuous complicated multi-layered carbonate/oxide structure is siderite FeCO 3 in both types of steel. T2 - EUROCORR 2011 - Developing solutions for the global challenge CY - Stockholm, Sweden DA - 04.09.2011 KW - Steel KW - Pipeline KW - Corrosion KW - Carbonate layer KW - CCS KW - CO2-storage PY - 2011 SP - Paper 1044-1 EP - Paper 1044-8 AN - OPUS4-28008 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pfennig, Anja A1 - Linke, B. A1 - Schulze, S. A1 - Kranzmann, Axel T1 - Static and dynamic long term corrosion experiments in CCS-conditions N2 - Dealing with first corrosion screening experiments to predict the reliability and safety of Germanys first Carbon Capture and Storage site in the northern Bassin of Germany, northwest of the Capital Berlin, laboratory experiments have been established to simulate the particular conditions at T=60 °C, highly saline aquifer water similar to 'Stuttgart Aquifer', but only at ambient pressure. With mounting 2 independent full 2-grade titanium autoclave systems (running up to 250 bar and 300 °C) pressures up to p=100 bar are possible. In 2010 a specific corrosion chamber of 2-grade titanium working up to 100 °C, flowing aqui fer water with different gas mixtures was designed to fit to a high cycle fatigue testing machine. Long term fatigue experiments simulating fatigue crack growth under corrosive environments will soon start. These experiments may not only help engineering a CCS site, but results can be used to improve the maintenance of geothermal energy production sites, especially moved parts such as pumps and shafts. T2 - EUROCORR 2011 - Developing solutions for the global challenge CY - Stockholm, Sweden DA - 04.09.2011 KW - CO2 KW - Static corrosion KW - High cycle fatigue KW - Steel KW - CCS KW - CO2-storage KW - Corrosion PY - 2011 SP - 1 EP - 7 (Paper 1087) AN - OPUS4-28009 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schälike, Stefan A1 - Mishra, Kirti Bhushan A1 - Wehrstedt, Klaus-Dieter A1 - Schönbucher, A. T1 - Experimentelle Untersuchung der Massenabbrandraten multipler n-Heptan und Di-tert-butylperoxid Poolfeuer N2 - Es werden Experimente zur Bestimmung der Massenabbrandraten von multiplen Poolfeuern präsentiert. Als Modellsubstanzen dienen n-Heptan und Di-tert-butylperoxid (DTBP). Es werden Versuche im Labormaßstab mit Durchmessern von d = 6 cm und relativen Abständen von 0.08 ≤ D/d ≤ 4 beschrieben und durch Feldversuche mit Pooldurchmessern d = 1.5 m und relativen Abständen zwischen den Pool von 0.17 ≤ D/d ≤ 1 ergänzt. Es kann gezeigt werden, dass die Massenabbrandraten multipler Feuer im Vergleich zu Einzelfeuern mit gleicher Brennstoffoberfläche bis zu einem Faktor 5.9 (n-Heptan) und 1.6 (DTBP) erhöht sind. Die Erhöhung ist abhängig vom relativen Abstand zwischen den Pools D, der Anzahl der Pools N und vom jeweiligen Brennstoff und zeigt ein lokales Maximum, welches mit dem Merging-Bereich der Flammenverschmelzung zusammenfällt. Die Massenabbrandrate als Funktion des relativen Abstandes zwischen den Pools kann durch eine Vergrößerung der Flammenbodenoberfläche infolge Flammenverschmelzung erklärt werden. T2 - 3. Magdeburger Brand- und Explosionsschutztag / vfdb-Workshop CY - Magdeburg, Germany DA - 22.03.2013 KW - Multiple Poolfeuer KW - Massenabbrandraten KW - n-Heptan KW - DTBP PY - 2013 SN - 978-3-00-041601-9 SP - 1 EP - 11 AN - OPUS4-27982 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mohamed, Zeinab A1 - Krüger, Simone A1 - Friedrich, Jörg Florian T1 - Deposition of thick polymer or inorganic layers with flame-retardant properties by combination of plasma and spray processes N2 - Mixtures of hexamethyldisiloxane (HMDSO) and oxygen have been used for deposition of SiO2-like layers by plasma polymerization under low-pressure conditions onto polyethylene and polystyrene used as basecoat. Water glass was cast onto these 0.5 pm plasma thick siloxane-like layers with a thickness of 5 to 40 mu m. The adhesion of these bilayer systems and their flame resistance were tested. The effect of different plasma parameters such as monomer/gas ratio, pressure and power input into the discharge on the deposition rate and the composition of the formed layers was studied. Characterization and chemical composition of the formed films were performed using infrared, X-ray photoelectron and solid state nuclear magnetic resonance spectroscopy. Peel strengths of composites were measured and the locus of peel front propagation was detected. Thermal properties of composites were analyzed by thermo-gravimetric analysis. Finally, the fire-retardant properties of thick coated polymers were determined by exposure to flames and the behavior of coatings on the polymers during flaming was observed visually. T2 - 3. Magdeburger Brand- und Explosionsschutztag / vfdb-Workshop CY - Magdeburg, Germany DA - 21.03.2013 KW - Polymer KW - Plasmatechnologie KW - Analytik PY - 2013 SN - 978-3-00-041601-9 SP - 1 EP - 11 AN - OPUS4-27988 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Simone A1 - Deubel, Jan A1 - Werrel, Martin A1 - Raspe, Tina A1 - Fettig, Ina A1 - Berger, Anka T1 - Brandtechnologische und chemisch-analytische Untersuchungen zum Einfluss von Brandbeschleunigern bei Zimmerbränden N2 - Anhand von 5 verschiedenen Zimmerbrandversuchen wurde der Einfluss von Brandbeschleunigern auf den Brandverlauf experimentell untersucht. Es wurden verschiedene brandtechnologische Kennwerte, wie der Massenverlust des gesamten Brandraums, Brandraumtemperaturen, die Wärmefreisetzungen sowie die Rauchgasemissionen ermittelt und beurteilt. Die Rauchgasanalyse erfolgte im Schlot, im Brandraum sowie in der Brandraumöffnung mittels Fourier Transformierte Infrarot-FTIR-Spektroskopie. Neben diesen brandtechnologischen Untersuchungen erfolgten auch chemisch-analytische Untersuchungen nach dem Brand, mit dem Ziel, den eingesetzten Brandbeschleuniger nachzuweisen. Im Anschluss an die jeweiligen Zimmerbrandversuche wurden verschiedene Brandrückstandsproben aus dem Brandschutt, Wischproben von den Wänden und den übriggebliebenen Gegenständen sowie Proben in Form von Adsorbensmaterialien und Tenax-Röhrchen genommen und mit Hilfe der HSSPME-GC-MS-Methode (Headspace-Solid Phase Micro Extraction-Gas Chromatographie-Massenspekrometrie) in Hinblick eines möglichen Brandbeschleunigernachweis analysiert. T2 - 3. Magdeburger Brand- und Explosionsschutztag / vfdb-Workshop CY - Magdeburg, Germany DA - 21.03.2013 KW - Analytik KW - Brandbeschleuniger KW - Raumbrand PY - 2013 SN - 978-3-00-041601-9 SP - 1 EP - 10 AN - OPUS4-27991 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mishra, Kirti Bhushan A1 - Wehrstedt, Klaus-Dieter ED - Leipertz, A. T1 - Peroxy-fuels: potential applications in combustion engines N2 - Present work deals with the potential usage of peroxy-fuels (usually known as organic peroxides) in engine combustion processes. Although as additives (in small quantities < 5% to conventional fuels e.g. diesel, gasoline) peroxy-fuels are well known for many years their commercial applications as a main or primary fuel are not investigated in detail as such except a few. Since they are thermally unstable and energetic their safety demands great care during processing which restricts their commercial exploitation. However, once the issues with safety are resolved they can be much more advantageously employed than conventional fuels. Some of these advantages are: significant amount of fuel saving, reduction in amount of inducted air or even in the complete absence of air i.e. anaerobically, smaller volume of combustion (chamber), oxygenated fuel quality and low emissions. In this study we introduce an idea to develop the components of an engine operating solely on peroxy-fuels. The engine concept is based on single and multiple injectors in a cylinder with special material coating to ensure a temperature controlled processing. T2 - 11th International congress on engine combustion processes - current problems and modern techniques CY - Ludwigsburg, Germany DA - 14.03.2013 KW - Industrial fires KW - Storage units KW - Safety measures KW - Explosion KW - Overpressure KW - CFD simulation PY - 2013 SN - 3-931901-87-4 N1 - Serientitel: Berichte zur Energie- und Verfahrenstechnik (BEV) – Series title: Berichte zur Energie- und Verfahrenstechnik (BEV) IS - 13.1 SP - 157 EP - 164 AN - OPUS4-27951 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weltschev, Margit A1 - Kohl, Anka A1 - Haufe, Manuela A1 - Werner, Jan T1 - Use of Fourier transform infrared spectroscopy to characterize nitric acid oxidation of polyethylene grades N2 - Resistance to oxidative degradation by nitric acid has been selected for a comparison of polyethylene grades in a European standard on suitability proof for alternative plastic resins used for packagings and intermediate bulk containers (IBCs) for the transport of dangerous goods. Measurements of the infrared (IR) absorption spectra of microtome slices cut from the walls of jerricans, which were pre-stored with 55% nitric acid for 21 and 42 days at 40°C, showed changes in the structure of the polyethylene. The penetration depths of 55% nitric acid into the polyethylene grades are, in principle, suitable for evaluating the resistance to oxidative degradation of polyethylene grades after pre-storage of the packagings for 21 days. After this period the packaging wall is not fully penetrated. The intensities of the IR bands at 1565 cm-1 (-NO2), 1630 cm-1 (-C=C) and 1654 cm-1 (-O-NO2) increased with the treatment time with 55% nitric acid as a result of oxidative damage by the nitric acid. The high increase in absorbance of the -C=C band in the region 1630 - 1690 cm-1 is attributable to paraffinic chain cracks. The absorbance of the -O-NO2 band, formed as result of the nitration process was still low at a test temperature of 40°C. T2 - NACE International Corrosion Conference 2013 CY - Orlando, FL, USA DA - 17.03.2013 KW - Polyethylenformstoffe KW - Beständigkeit gegen oxidativen Abbau KW - Salpetersäure KW - Eindringtiefen KW - FTIR KW - Verpackungen zum Transport von Gefahrgütern PY - 2013 SN - 978-1-627-48145-8 SP - 1 EP - 11 (Paper No. 2070) PB - Curran CY - Red Hook, NY AN - OPUS4-27981 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rogge, Andreas T1 - Vorbeugender Brandschutz in Tunnelbauwerken T2 - Deutscher Bautechnik-Tag CY - Hamburg, Germany DA - 2013-04-11 PY - 2013 N1 - Serientitel: DBV-Hefte – Series title: DBV-Hefte IS - 21 SP - 157 EP - 158 AN - OPUS4-28289 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jaunich, Matthias A1 - Stark, Wolfgang A1 - Wolff, Dietmar T1 - Behaviour of rubber seals at low temperatures - results of component tests - N2 - The investigation of low temperature properties of elastomeric sealing materials by means of thermo-analytical methods is a sound way to get information about the glass transition process. The breakdown temperature of the sealing function of O-ring seals was measured in a component test setup depending on material and degree of compression. An in depth explanation of the observed component tests behaviour is currently in preparation. It requires the results of thermo-analytical methods and measurements as the compression set (not shown here). With that, a model was developed to describe the correlation between physical material parameters and observed component behaviour. T2 - Jahrestagung Kerntechnik 2013 CY - Berlin, Germany DA - 14.05.2013 PY - 2013 SP - 1 EP - 6 AN - OPUS4-28574 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Poli, Marco A1 - Grätz, Rainer A1 - Schröder, Volkmar ED - Pierucci, S. ED - Klemes, J.J. ED - De Rademaeker, E. ED - Fabiano, B. ED - Buratti, S.S. T1 - Limitations of gas explosion venting due to accelerated flame propagation and elevated initial pressure N2 - Many industrial processes include a gas explosion hazard. If safety measures are not adequate to prevent a potentially explosive atmosphere or to avoid effective ignition sources in enclosures, at least the effects of an explosion can be limited e.g. by gas explosion venting systems. For the design of gas explosion venting systems for confinements only little guidance is given when considering the constructional boundary conditions or process conditions. For this reason conservative assumptions are prevalent in practice and in many cases the protective systems become significantly oversized. From safety perspective such safety margins in venting areas can lead to a critical acceleration of the pressure rise. Moreover, a gas explosion venting at turbulent conditions caused by over sizing or by obstacles rather leads to an under-sized system. The present investigation was focused especially on the influence of certain obstacles as well as the influence of elevated initial pressures on explosion venting behaviour of quiescent hydrogen, methane or ethylene in air. T2 - 14th International symposium on loss prevention and safety promotion in the process industries CY - Florence, Italy DA - 12.05.2013 KW - Gas explosion venting KW - Turbulent combustion KW - Obstacles PY - 2013 SN - 978-88-95608-22-8 DO - https://doi.org/10.3303/CET1331111 SN - 1974-9791 N1 - Serientitel: Chemical engineering transactions – Series title: Chemical engineering transactions VL - 31 SP - 661 EP - 666 PB - AIDIC, Associazione Italiana di Ingegneria Chimica CY - Milano AN - OPUS4-28582 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Liebner, Christian A1 - Heinrich, Sebastian A1 - Edeling, Florian A1 - Hieronymus, Hartmut A1 - Lange, T. A1 - Klemm, E. ED - Pierucci, S. ED - Klemes, J.J. ED - De Rademaeker, E. ED - Fabiano, B. ED - Buratti, S.S. T1 - Explosion initiation, propagation, and suppression inside a micro structured reactor N2 - The present contribution reports on specific aspects of safety engineering in heterogeneously catalysed oxidation reactions. Results for ethene-oxygen-mixtures in a continuous-flow micro reactor are reported related to the safety issues of the ethylene oxide process. Initial pressure is ranging from below 1 bar up to 10 bar at initial temperatures ranging from room temperature up to 673 K. Micro structured reactors offer an extended range of operating conditions. The key issue to be discussed in the present contribution is how to safely operate a micro reactor at conditions in conventional devices to be characterised as inside the explosion region. Within certain limits suppression of explosion inside a micro reactor can be achieved. This holds true for chain reactions as well as runaway reactions. Nevertheless it is not possible to safely operate micro structured reactors at any condition. Therefore, explosion propagation through a Micro structured reactor and initiation of gas phase explosions by hot spots inside the reactor were investigated. The investigation methods applied are subject to actual standardization. T2 - 14th International symposium on loss prevention and safety promotion in the process industries CY - Florence, Italy DA - 12.05.2013 KW - Micro reactor KW - Explosion KW - Safety PY - 2013 SN - 978-88-95608-22-8 DO - https://doi.org/10.3303/CET1331101 SN - 1974-9791 N1 - Serientitel: Chemical engineering transactions – Series title: Chemical engineering transactions IS - 31 SP - 601 EP - 606 PB - AIDIC, Associazione Italiana di Ingegneria Chimica CY - Milano AN - OPUS4-28583 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schälike, Stefan A1 - Mishra, Kirti Bhushan A1 - Wehrstedt, Klaus-Dieter A1 - Schönbucher, A. T1 - Limiting distances for flame merging of multiple n-heptane and di-tert-butyl peroxide pool fires N2 - Experiments to determine the limiting distances for flame merging of multiple pool fires are presented. As model substances n-heptane and di-tert-butyl peroxide are used. Laboratory scale tests with a Diameter d = 6 cm and relative distances between the pools of 0.08 ≤ D/d ≤ 4 are described and complemented with field experiments with a diameter d = 1.5 m and relative distances between the pools of 0.17 ≤ D/d ≤ 1. Three regions for flame merging are observed and limiting distances are determined. A merging Region with the limiting distance Dmerg/d within which all flames merge together over the complete burning time. A transition region with the limiting distance Dtran/d within which some flames merge together while other flames are separated from each other. A separated region within which all flames are completely separated from each other. A correlation against the number of burning pools is presented to predict the limiting distances Dmerg/d und Dtran/d. T2 - ICheaP-11 - 11th International conference on chemical & process engineering CY - Milan, Italy DA - 02.06.2013 KW - Multiple fires KW - Flame merging KW - Mass burning rate KW - Limiting distances KW - Pool fire KW - Experimental study KW - Di-tert-butyl peroxide PY - 2013 SN - 978-88-95608-23-5 DO - https://doi.org/10.3303/CET1332021 SN - 1974-9791 N1 - Serientitel: Chemical engineering transactions – Series title: Chemical engineering transactions IS - 32 SP - 121 EP - 126 PB - AIDIC, Associazione Italiana di Ingegneria Chimica CY - Milan AN - OPUS4-28646 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Reich, Franziska A1 - Pötzsch, Klaus-Michael T1 - Experimentell gestützte Untersuchungen zu brandschutztechnischen Maßnahmen im Gefahrguttransport N2 - Um das Risiko eines katastrophalen Versagens von Gefahrguttanks und deren Folgen zu mindern werden sicherheitstechnische Maßnahmen an der Bundesanstalt für Materialforschung und -prüfung (BAM) untersucht. Der Einsatz und die Dimensionierung von brandschutztechnischen Maßnahmen im Gefahrguttransport sind durch verkehrsträgerspezifische Vorschriften geregelt. Hiernach sind Gefahrguttanks für betriebliche Belastungen auszulegen. Bei dieser Auslegung werden unter Anderem Parameter, wie die Wanddicke eines Gefahrguttanks, stoffliche Aspekte des transportierten Gefahrguts und auch Betriebsdrücke berücksichtigt. Eine seit vielen Jahren bewährte Sicherheitsphilosophie ist es, Tanks oder druckführende Anlagen durch Sicherheitseinrichtungen gegen das unzulässige Überschreiten eines inneren Überdrucks zu schützen. Die regelkonforme Auslegung führt jedoch zu unterschiedlichen Sicherheitsniveaus in Europa und darüber hinaus. Denn hiernach werden Tanks nach zwei Philosophien befördert. Insbesondere betrifft dies die Ausrüstung der Tanks mit Druckentlastungseinrichtungen, wie Sicherheitsventile. Daraus ergeben sich Fragestellungen, die es im Rahmen der Untersuchungen in einem drittmittelgeförderten BMVBS-Projektes, zu beantworten galt: • Warum verkehren Tanks mit und ohne Sicherheitsventile? • Sind diese Sicherheitseinrichtungen auch in Unfallsituationen ausreichend, um die Temperatur und den Druck im Tank herabzusetzen? Bei den Untersuchungen des Forschungsprojektes wurde unter anderem die Zuverlässigkeit der Sicherheitseinrichtungen an Gefahrguttanks für den normalen Betrieb und für den Brandfall untersucht. Diese Untersuchungen zeigen, dass das Sicherheitsempfinden, welches Sicherheitsventile vermitteln, zu hinterfragen ist. T2 - Vfdb 2013 - 61. Jahresfachtagung CY - Weimar, Germany DA - 27.05.2013 KW - Gefahrguttanks KW - Transporttanks KW - Druckentlastungseinrichtung KW - Brandschutzbeschichtung PY - 2013 SP - 737 EP - 752 CY - Altenberge AN - OPUS4-28649 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Patrick P. A1 - Wosniok, Aleksander A1 - Lazik, D. A1 - Bartholmai, Matthias T1 - Test field for the validation of a multifunctional sensor for distributed subsurface monitoring of gas storage areas N2 - BAM Federal Institute for Materials Research and Testing, in cooperation with the company MeGaSen UG carries out a research project to enhance and validate an innovative approach for distributed subsurface monitoring of gas storage areas. The concept combines different measurement technologies to one multifunctional sensor: membrane-based gas measurement technology for in-situ monitoring of gases in soil and fiber optical sensing of temperature and strain (as a measure for structural change). Key aspect of the research project is the first-time validation of the system in an application relevant dimension. For this purpose a 20 x 20 m2 test field is build. A comprehensive validation of the system is carried out by systematic variation of different parameters like position-dependent gasinjection, temperature and mechanical impact. T2 - Sensor 2013 - 16th International conference on sensors and measurement technology CY - Nürnberg, Germany DA - 14.05.2013 KW - Distributed multifunctional sensor KW - Subsurface monitoring KW - Gas storage areas KW - Membrane-based gas sensing KW - Fiber optical sensing PY - 2013 SN - 978-3-9813484-3-9 DO - https://doi.org/10.5162/sensor2013/P2.2 N1 - Serientitel: AMA Conferences – Series title: AMA Conferences SP - 713 EP - 716 AN - OPUS4-28652 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Komann, Steffen A1 - Droste, Bernhard A1 - Gröke, Carsten T1 - Qualitätssicherung und -überwachung bei Verpackungen für prüfpflichtige Versandstücke zur Beföderung radioaktiver Stoffe N2 - Ziel dieses Beitrages soll es sein, zum einen das Vorgehen bei der Erlangung einer Anerkennung zur qualitätsgesicherten Herstellung einer Verpackung für prüfpflichtige Versandstücke der zuständigen Behörde im Sinne des ADR Unterabschnittes 1.7.3 'Qualitätssicherung' darzustellen und zum anderen Probleme bei der Umsetzung der rechtsverbindlichen Vorschriften des Gefahrgutrechts aufzuzeigen. T2 - Jahrestagung Kerntechnik 2013 CY - Berlin, Germany DA - 14.05.2013 PY - 2013 IS - Sektion 5: Entsorgung radioaktiver Abfälle, Lagerung SP - 1 EP - 6 AN - OPUS4-28653 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Steffen, Milan A1 - Schukar, Marcus ED - Jaroszewicz, L.R. T1 - Integration of Cu-coated single-mode optical fiber into carbon/PEEK composite for distributed structural health monitoring based on Rayleigh backscatter reflectometry N2 - In this paper a technique for integrating copper coated silica optical fibers into AS-4/PEEK composite for Structural Health Monitoring (SHM) is presented. The integration steps are described in detail. X-ray and microscopic images indicate a successfully integrated optical fiber which does not seem to affect the fiber/matrix distribution around it. Optical backscatter reflectometry shows losses of approximately 2dBm-1 along the integrated parts of the optical fiber due to temperature induced shrinkage of the composite. T2 - EWOFS 2013 - 5th European workshop on optical fibre sensors CY - Kraków, Poland DA - 19.05.2013 KW - SHM KW - Optical KW - Fiber KW - Rayleigh KW - OFDR KW - Composite KW - Copper coating PY - 2013 DO - https://doi.org/10.1117/12.2025280 SN - 0277-786X N1 - Serientitel: Proceedings of SPIE – Series title: Proceedings of SPIE IS - Paper 8794 - 181 SP - 879430-1 EP - 879430-6 AN - OPUS4-28627 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krüger, Simone A1 - Deubel, Jan A1 - Werrel, Martin A1 - Raspe, Tina T1 - Welche stofflichen und energetischen Gefahren gehen von Wohnzimmerbränden aus? N2 - Welche stofflichen und energetischen Gefahren während und nach einem Wohnzimmerbrand auftreten können, werden im Rahmen dieses Vortrages vorgestellt. Im Mittelpunkt stehen dabei die Rauchgasentwicklung, die Wärmefreisetzung, die entstehenden Rauchgastemperaturen sowie die Rauchgaszusammensetzung. In den Einrichtungen der Gesellschaft für Materialforschung und Prüfungsanstalt für das Bauwesen Leipzig mbH (MFPA) wurden dazu fünf verschiedene Wohnzimmerbrandversuche durchgeführt. Die Modell-Zimmer wurden jeweils mit dem gleichen Mobiliar ausgestattet. Als Brandbeschleuniger kamen Benzin und Diesel als Gemisch zum Einsatz. Bei den Versuchen zeigte sich unter anderem, dass der Brandbeschleuniger deutlich die Zeit bis zum Flashover verkürzt. Aus den ermittelten Kennwerten zur Wärmefreisetzung und den Rauchgastemperaturen können Rückschlüsse auf die energetischen Gefahren abgeleitet werden. Die quantitative Erfassung toxischer Rauchgaskomponenten erfolgte mit Hilfe der Fourier-Transformations- Infrarot-(FTIR)-Spektroskopie. Die qualitative und quantitative Rauchgaszusammensetzung wurde dabei in der Brandraummitte, an der Brandraumöffnung, unter der Brandraumdecke und im Schlot ermittelt. Aus der Massenverlustrate und der quantitativen Rauchgasanalyse können Aussagen zur Rauchgastoxizität getroffen werden und die stofflichen Gefahren beurteilt werden. Das Wissen über die Bildung von energetischen und stofflichen Brandprodukten ermöglicht somit eine risikogerechte Beurteilung der Brandgefahren bei Raumbränden, auch in Hinblick auf die unterschiedlichen Brandphasen. T2 - Vfdb 2013 - 61. Jahresfachtagung CY - Weimar, Germany DA - 27.05.2013 KW - Brand KW - Rauchgasanalytik PY - 2013 SP - 771 EP - 787 CY - Altenberge AN - OPUS4-28628 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maierhofer, Christiane A1 - Krankenhagen, Rainer A1 - Reischel, Mercedes A1 - Myrach, Philipp A1 - Steinfurth, Henrik A1 - Röllig, Mathias T1 - Anwendung der aktiven Thermografie zur zerstörungsfreien Prüfung von Faserverbundwerkstoffen T1 - Application of active thermography for non-destructive testing of fibre reinforced composites N2 - In diesem Beitrag werden Anwendungsbeispiele der aktiven Thermografie zur zerstörungsfreien Untersuchung von Faserverbundwerkstoffen vorgestellt. Ziel der Anwendung und Weiterentwicklung des Verfahrens ist nicht nur die Ortung, sondern auch die quantitative Beschreibung von Fehlstellen und Schäden. N2 - In this paper case studies are presented concerning non-destructive testing of fibre reinforced composites using active thermography. The main objective of the application and further development of the method is not only the detection, but also the quantitative characterisation of faults and damage. T2 - Temperatur 2013 - Verfahren und Geräte in der Temperatur- und Feuchtemesstechnik CY - Berlin, Germany DA - 05.06.2013 KW - CFK KW - Impact-Schaden KW - Aktive Thermografie KW - Blitzanregung KW - Temperaturleitfähigkeit PY - 2013 SN - 3-9810021-8-0 SP - 143 EP - 148 AN - OPUS4-28836 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Witt, Jens A1 - Krebber, Katerina A1 - Demuth, J. A1 - Sasek, L. T1 - Fiber optic heart rate sensor for integration into personal protective equipment N2 - This paper reports on a fiber optic sensor for heart rate measurements. The sensor will be integrated into personal protective equipment within the framework of the FP7 EU project i-Protect. Two different sensor prototypes were developed. One is based on fiber Bragg gratings in silica fiber and the other one is based on macrobending effects in polymer optical fiber. T2 - International workshop BioPhotonics 2011 CY - Parma, Italy DA - 08.06.2011 KW - Smart textile KW - Healthcare monitoring KW - Fiber optical sensor KW - FBG KW - Heart rate sensor KW - Macrobending sensor PY - 2011 SN - 978-1-4244-9837-6 DO - https://doi.org/10.1109/IWBP.2011.5954836 IS - Th6.26 SP - 1 EP - 3 AN - OPUS4-24498 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Witt, Jens A1 - Schukar, Marcus A1 - Breithaupt, Mathias A1 - Müller, Bernd R. A1 - Krebber, Katerina T1 - MPOF LPGs as radiation sensors N2 - We investigated to our knowledge for the first time the capabilities of long period gratings (LPG) in single-mode microstructured polymer optical fibre (mPOF) as real-time gamma dosimeter. The fibre is made from polymethyl methacrylate (PMMA) with a polycarbonate jacket. We measured the radiation-induced wavelength shift of the mPOF LPG loss feature wavelength and the radiation-induced attenuation of a mPOF for different wavelength between 600 nm and 800 nm for gamma radiation with an energy distribution between 6 keV and 18 keV. T2 - POF 2011 - 20th International conference on plastic optical fibers CY - Bilbao, Spain DA - 14.09.2011 KW - Microstructured polymer optical fibre (mPOF) KW - Long period grating (LPG) KW - Radiation sensor PY - 2011 SP - 1 EP - 3 AN - OPUS4-24499 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Witt, Jens A1 - Schukar, Marcus A1 - Krebber, Katerina A1 - Demuth, J. A1 - Sasek, L. T1 - Heart rate sensor for integration into personal protective equipment N2 - This paper reports on a fibre optic sensor for heart rate measurement which is developed within the framework of the FP7 EU project i-Protect. Goal is integration of the sensor into personal protective equipment Two different sensor prototypes based on polymer optical fibre (POF) were developed. One is based on long period gratings in microstrutured POF and the other one is based on macrobending effects in POF. T2 - POF 2011 - 20th International conference on plastic optical fibers CY - Bilbao, Spain DA - 14.09.2011 KW - Heart rate sensor KW - Long period grating KW - Macrobending sensor KW - Microstructured POF (mPOF) KW - Personal protective equipment (PPE) KW - Physiological sensor PY - 2011 SP - 1 EP - 5 AN - OPUS4-24500 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Witt, Jens A1 - Breithaupt, Mathias A1 - Erdmann, Jessica A1 - Krebber, Katerina T1 - Humidity sensing based on microstructured POF long period gratings N2 - We investigated the capabilities of long period gratings (LPG) in single-mode microstructured polymer optical fibre (mPOF) for humidity sensing. For that mPOF LPGs were exposed to different humidity levels at a constant temperature of 30°C in a climate chamber. During the long term tests, which took up several weeks, the humidity was changed in several steps while mPOF LPG wavelength and fibre attenuation were measured. We also measured the water uptake of mPOF in environment with different relative humidity. T2 - POF 2011 - 20th International conference on plastic optical fibers CY - Bilbao, Spain DA - 14.09.2011 KW - Microstructured polymer optical fibre (mPOF) KW - Long period grating (LPG) KW - Humidity sensor PY - 2011 SP - 1 EP - 6 AN - OPUS4-24501 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pauli, Jutta A1 - Brehm, Robert A1 - Grabolle, Markus A1 - Behnke, Thomas A1 - Mathejczyk, J. A1 - Hamann, F. A1 - Alves, F. A1 - Hilger, I. A1 - Resch-Genger, Ute ED - Achilefu, S. ED - Raghavachari, R. T1 - Dye-biomolecule conjugates and NIR-fluorescent particles for targeting of disease-related biomarkers N2 - Indispensable for fluorescence imaging are highly specific and sensitive molecular probes that absorb and emit in the near infrared (NIR) spectral region and respond to or target molecular species or processes. Here, we present approaches to targeted fluorescent probes for in vivo imaging in the intensity and lifetime domain exploiting NIR dyes. Screening schemes for the fast identification of suitable fluorophores are derived and design criteria for highly emissive optical probes. In addition, as a signal amplification strategy that enables also the use of hydrophobic NIR fluorophores as fluorescent reporters, first steps towards versatile strategies for the preparation of NIR-fluorescent polymeric particles are presented that can be utilized also for the design of targeted and analyte-responsive probes. KW - Fluorescence KW - Fluorescence lifetime imaging KW - Near-infrared KW - NIR KW - Cyanine dye KW - Cancer KW - In vivo imaging KW - Aggregation KW - Nanoparticle PY - 2011 DO - https://doi.org/10.1117/12.876828 SN - 1605-7422 N1 - Serientitel: Proceedings of SPIE – Series title: Proceedings of SPIE IS - 7910 SP - 791014-1 EP - 791014-15 AN - OPUS4-24353 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ünal, Murat A1 - Kühne, Hans-Carsten T1 - Dalles de verre - damage mechanisms, maintenance techniques and mortars for restoration N2 - The present article gives an insight into the research project BEGLARES. Main topics are the restoration “Dalles de Verre” Windows and the development of repair mortars and techniques. This project is executed in cooperation between Glasmalerei Peters GmbH, the University of York, and the BAM Federal Institute for Materials Research and Testing. It is funded by the Federal Ministry of Economics and Technology. The main mechanism of damage, Standards for protection and repair of concrete structures, and the development of repair mortar and special test specimens are presented. T2 - EWCHP-2011 - European workshop on cultural heritage preservation CY - Berlin, Germany DA - 26.09.2011 KW - Dalles de verre KW - Carbonation KW - Maintenance planning KW - Current state analysis KW - Repair techniques PY - 2011 SN - 978-3-8167-8560-6 SP - 289 EP - 293 AN - OPUS4-24560 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ramge, Peter A1 - Kühne, Hans-Carsten A1 - Meng, Birgit T1 - Repair mortars for the restoration and reprofiling of natural stone elements in cultural heritage N2 - For the protection of the world's cultural heritage the restoration of listed buildings and monuments is an important task. In many cases the need to repair and reprofile natural stone elements occurs. Repair mortars for such applications have to match historicocultural interests as well as durability related and constructive interests. Currently a research project dealing with the development and optimisation of such mortars is set up at the BAM. Special focus is laid on the possibility of a modular adaption to match a vast variety of stone properties. Besides the development and lab scale testing of the mortar system, an in-situ application will be planned and executed. T2 - EWCHP-2011 - European workshop on cultural heritage preservation CY - Berlin, Germany DA - 26.09.2011 KW - Repair mortar KW - Natural stone KW - Stone restoration KW - Stone reprofiling KW - Modular system KW - Listed buildings and monuments PY - 2011 SN - 978-3-8167-8560-6 SP - 281 EP - 288 AN - OPUS4-24561 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herbst, Tristan A1 - Rübner, Katrin A1 - Meng, Birgit A1 - Hauer, B. T1 - Assessment concept for the sustainable use of secondary aggregates in concrete N2 - Nowadays there are several applications of mineral recycling materials and residues. At present an assessment method for the use of secondary raw materials, which considers sustainability aspects, does not exist. In the framework of the German DAfStb/BMBF research project 'Sustainable Building with Concrete' an assessment concept was developed. It includes the following four assessment steps: I. Basic considerations, II. Advantages for sustainable construction, III. Alternative paths for application, and IV. Sensitivity analysis. The concept was developed on the basis of recycled concrete aggregates, which are already used according to German standards. Afterwards, it was applied and verified by the evaluation of the utilisation of municipal solid waste incinerator bottom ashes. T2 - International RILEM conference on advances in construction materials through science and engineering CY - Hong Kong, China DA - 05.09.2011 KW - Sustainability KW - Assessment KW - Secondary aggregates KW - Concrete PY - 2011 SN - 978-2-35158-116-2 VL - PRO 79 IS - Chapter 10 / Study of sustainable use... SP - 1 EP - 8 PB - RILEM Publications AN - OPUS4-24564 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmigalla, S. A1 - Heyn, Andreas A1 - Wesling, V. A1 - Reiter, R. A1 - Echtermeyer, P. T1 - Investigation of the pitting corrosion behaviour of nickel based alloy claddings by evaluation of electrochemical noise measurements N2 - Claddings of different nickel based alloys were generated on a mild Steel (S235JR) and a stainless steel type 304 by Cold Metal Transfer (CMT). This welding procedure possesses a low degree of mixing between the Substrate and cladding material. Thus it improves the corrosion behaviour of the claddings. The aim of our investigations was to examine the effect of the welding parameters: energy per unit length, shielding gas and finishing surface treatment on the pitting corrosion behaviour of the claddings. However, under Standard test conditions nickel based alloys are often resistant to pitting corrosion. Moreover these test methods are inaccurate and require a large period of time resulting from the iterative progress to determine the critical pitting temperature (CPT). A potentiostatic test method was modified using a high concentrated CaCI2-solution and a conventional three electrode measuring cell. The pitting corrosion behaviour is calculated from current noise charges. During the test the course of corrosion is detected online by the evaluation of electrochemical noise Signals while a continuous increase of temperature by a defined heating rate is realised. Thus a critical pitting temperature can be estimated by only one attempt. Furthermore the deviation of the measured CPT is very low compared to Standard tests using gravimetrical and microscopic evaluation. That enables to figure out the influence of the welding parameters in an exact way. T2 - EUROCORR 2011 - Developing solutions for the global challenge CY - Stockholm, Sweden DA - 04.09.2011 KW - Nickelbasislegierung KW - Plattieren KW - Schweißverfahren KW - Cold metal transfer KW - Korrosionsprüfung KW - Elektrochemie KW - Elektrochemisches Rauschen PY - 2011 SP - 1 EP - 9 AN - OPUS4-24565 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin T1 - Abbruchmethoden vor dem Hintergrund der Ersatzbaustoffverordnung N2 - Beim Abbruch von Gebäuden wird eine Vielzahl von unterschiedlichen Techniken eingesetzt. Der mit Abstand größte Teil der Abbrucharbeiten wird dabei mit mechanischen Verfahren ausgeführt. In Abhängigkeit vom rückzubauenden Gebäude können aber auch hydrodynamische Verfahren (z. B. Hochdruckwasserstrahlen), thermische Verfahren (z. B. Schneidbrennen) oder chemische Verfahren (z. B. Sprengen) angewandt werden. T2 - BGRB-Kongress - Ressourcenschonung durch Baustoff-Recycling CY - Königswinter/Bonn, Deutschland DA - 13.09.2011 KW - Bauschutt KW - Ersatzbaustoffverordnung PY - 2011 SP - 23 EP - 26 AN - OPUS4-24508 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kusche, Nadine A1 - Schukar, Vivien A1 - Schilder, Constanze A1 - Köppe, Enrico A1 - Habel, Wolfgang ED - Chang, F.-K. T1 - Development and qualification of FBG-based strain patches and rosettes N2 - A fibre Bragg grating (FBG) strain patch specially adapted for long-term and high-strain applications was developed and characterised. Additionally, in the case of unknown main stress axis, two fibre optic strain rosettes were developed. The design concept for the patch and the rosettes is based on a glass fibre reinforced plastic (gfrp) carrier material. The patches were characterised due to their strain gauge factor and fatigue behaviour. As a result, FBG strain patches with linear strain behaviour and excellent fatigue resistance were developed and can be used as part of a monitoring system for aerospace structures or wind turbine power plants. The rosettes were designed to be small in geometrical size and their strain transfer behaviour was characterised. T2 - 8th International workshop on structural health monitoring 2011 CY - Stanford, CA, USA DA - 13.09.2011 KW - Fibre Bragg grating KW - Patch KW - Rosette KW - Strain gauge factor KW - Fatigue behaviour KW - Validation PY - 2011 SN - 978-1-60595-053-2 VL - 2 SP - 1457 EP - 1465 PB - DEStech Publications, Inc. AN - OPUS4-24512 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erning, Johann Wilhelm T1 - Desinfektionsmaßnahmen - Beständigkeit von Werkstoffen N2 - Der hygienisch einwandfreie Betrieb einer Trinkwasserinstallation ist auch für den Fall komplexer Systeme wie in Krankenhäusern oder Alten- und Pflegeheimen möglich. Notwendige Voraussetzung ist die Beachtung der Vorgaben der allgemein anerkannten Regeln der Technik bei Planung, Ausführung und Betrieb. Zusätzliche Geräte oder die Zugabe von Chemikalien sind dann regelmäßig nicht erforderlich. Im Schadensfall ist die korrekte und umfassende Ermittlung der Ursache für die Beeinträchtigung der Schlüssel zur dauerhaften Abhilfe. Nur die Beseitigung von Mängeln und die Wiederherstellung regelgerechter Betriebsbedingungen ermöglichen dauerhaft störungsfreien Betrieb. Die prophylaktische Zugabe von Desinfektionsmitteln ist weder zulässig noch sinnvoll, ebenso wenig ist damit eine dauerhafte Sanierung von auftretenden Mängeln möglich. Zudem ergibt sich ein erhöhtes Risiko für Schäden durch Korrosion in den dauerhaft mit oxidierenden Substanzen beaufschlagten Installationen. T2 - 3. Deutsches Forum 'Innenraumhygiene' CY - Essen, Deutschland DA - 15.02.2011 PY - 2011 SN - 1615-8695 IS - Kap.: Trinkwasser SP - 1 EP - 9 AN - OPUS4-24541 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mix, Renate A1 - Ramanujam, Maalolan A1 - Wachtendorf, Volker A1 - Friedrich, Jörg Florian ED - Reichert, T. T1 - New ways for early detection of polymer ageing N2 - Photo-oxidative ageing of polymers under defined exposure (UV, humidity) was investigated from two points of view: a) the ageing process Starts from the topmost surface and penetrates slowly towards bulk and b) radicals play an important role among ageing. Therefore, X-ray photoelectron (XPS) and electron spin resonance (ESR) spectroscopy were applied to show both, the progressive incorporation of oxygen during in-situ UV irradiation (XPS) and the formation of radicals (ESR) in the polymer. The intensity of ESR Signals served as measure for radical concentration. The Validation of this correlation was checked for polyethylenes (PE) equipped with different concentrations of Hostavin N30 UV stabilizer. T2 - 5th European weathering symposium - Natural and artificial ageing of polymers CY - Lisbon, Portugal DA - 21.09.2011 PY - 2011 SN - 978-3-9813136-2-8 N1 - Serientitel: CEEES Publication – Series title: CEEES Publication IS - 15 SP - 157 EP - 163 PB - GUS (Gesellschaft für Umweltsimulation) CY - Pfinztal AN - OPUS4-24535 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ramanujam, Maalolan A1 - Wachtendorf, Volker A1 - Mix, Renate A1 - Schönhals, Andreas A1 - Friedrich, Jörg Florian ED - Reichert, T. T1 - Influence of UV weathering and humidity on surface & bulk properties of LDPE N2 - The outdoor weathering of polymers is mainly due to UV radiation, water, Pollution, humidity, temperature etc. To understand the effects of weathering, simulated tests need to be undertaken in lab scale. Such tests must be quite efficient and similar to the effects of natural weathering. This paper mainly focuses on the effects of UV radiation along with humidity on LDPE. T2 - 5th European weathering symposium - Natural and artificial ageing of polymers CY - Lisbon, Portugal DA - 21.09.2011 KW - LDPE KW - UV weathering KW - Humidity PY - 2011 SN - 978-3-9813136-2-8 N1 - Serientitel: CEEES Publication – Series title: CEEES Publication IS - 15 SP - 211 EP - 218 PB - GUS (Gesellschaft für Umweltsimulation) CY - Pfinztal AN - OPUS4-24536 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Patrick P. A1 - Asadi, S. A1 - Schiller, J.H. A1 - Lilienthal, A.J. A1 - Bartholmai, Matthias T1 - An artificial potential field based sampling strategy for a gas-sensitive micro-drone N2 - This paper presents a sampling strategy for mobile gas sensors. Sampling points are selected using a modified artificial potential field (APF) approach, which balances multiple criteria to direct sensor measurements towards locations of high mean concentration, high concentration variance and areas for which the uncertainty about the gas distribution model is still large. By selecting in each step the most often suggested close-by measurement location, the proposed approach introduces a locality constraint that allows planning suitable paths for mobile gas sensors. Initial results in simulation and in real-world experiments with a gas-sensitive micro-drone demonstrate the suitability of the proposed sampling strategy for gas distribution mapping and its use for gas source localization. T2 - IEEE/RSJ International conference on intelligent robots and systems (IROS '11) / Workshop on robotics for environmental monitoring (WREM2011) CY - San Francisco, CA, USA DA - 25.09.2011 KW - Autonomous UAV KW - Chemical sensing KW - Gas distribution modelling KW - Gas source localization KW - Gas sensors KW - Mobile sensing system KW - Quadrocopter KW - Sensor planning KW - Artificial potential field PY - 2011 SP - 34 EP - 38 AN - OPUS4-24537 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jakubcová, Petra A1 - Rübner, Katrin A1 - Schnell, A. T1 - Nachhaltige Verwertung von Bau- und Abbruchabfällen im Bausektor N2 - Mineralische Sekundärrohstoffe finden im Beton als Gesteinskörnung, Betonzusatzstoff, Bestandteil von Zementen oder Spezialbindemitteln Anwendung. Für den Einsatz von rezyklierten Gesteinskörnungen, Kesselsand, Steinkohlenflugasche, Silicastaub und Hüttensand bestehen bereits Normen bzw. bauaufsichtliche Zulassungen. Für weitere Reststoffe, wie Mauerwerkbruch und beim Baustoffrecycling anfallende feinkörnige, heterogene Sandfraktionen, existieren noch keine höherwertigen Verwertungswege. In einem Forschungsprojekt werden derzeit Möglichkeiten zur Verwertung von heterogenen mineralischen Bau- und Abbruchabfällen durch Herstellung von Blähgranulaten mit maßgeschneiderten Eigenschaften (Schüttdichte, Rohdichte, Korngröße und Kornfestigkeit) untersucht. Dies eröffnet die Möglichkeit einer rohstofflichen Verwertung solcher Abfälle. Im Mittelpunkt der Untersuchungen steht der Mauerwerkbruch. Er fällt mit über 20 Tonnen pro Jahr an und weist im Vergleich zum Betonbruch größere Verwertungsdefizite auf hl. Die erzeugten Granulate sollen als leichte Gesteinskörnung im Beton, Schüttung oder Pflanzsubstrat Anwendung finden. Die ersten Ergebnisse der Granulatherstellung mit einer thermischen Behandlung zeigen, dass sich Mauerwerkbruch als Rohstoff zur Herstellung leichter Gesteinskörnungen eignet 121. Die so erzeugten Blähgranulate weisen ähnliche Eigenschaften wie herkömmliche Blähtöne auf 131. Das Hauptziel der in diesem Beitrag vorgestellten weiteren Untersuchungen war, die Rohdichte der Granulate bei gleichbleibender oder steigender Kornfestigkeit zu senken. Aus energetischer Sicht des Blähprozesses wurde neben dem thermischen Verfahren auch die Möglichkeit einer hydrothermalen Erhärtung der Granulate untersucht. T2 - Jahrestagung der Fachgruppe Bauchemie - Nachhaltige Verwertung von Bau- und Abbruchabfällen im Bausektor CY - Hamburg-Harburg, Germany DA - 06.10.2011 KW - Sekundärrohstoffe KW - Sekundäre Gesteinskörnung KW - Recycling KW - Leichtbeton PY - 2011 SN - 978-3-936028-69-0 N1 - Serientitel: GDCh-Monographien – Series title: GDCh-Monographien VL - 44 SP - 121 EP - 125 CY - Frankfurt/M. AN - OPUS4-25157 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schilder, Constanze A1 - Hofmann, Detlef A1 - Kohlhoff, Harald A1 - Habel, Wolfgang ED - Ramos, G. A. T1 - Structure-integrated fiber-optic strain wave sensor for concrete pile testing and monitoring N2 - Reinforced concrete piles are used in case of structures that are constructed on soft ground to transfer the loads into deeper strata with sufficient bearing capacity. In order to determine the pile’s behavior and possible damage, static and dynamic pile tests are carried out. Dynamic measurements taken from the pile head can show the bearing behavior and structural integrity by using the theory of wave propagation. In order to receive more precise information about the pile features, now, a string of sensors is embedded at different levels of the pile. A fiber optic strain wave sensor, based on the extrinsic Fabry-Perot interferometer (EFPI), has already been developed and tested in full-scale field tests by Schallert (2010). It was possible to detect the introduced deformation caused by the static load and the dilatational wave during dynamic loading. Although the full-scale tests were successful, the engineering design of the sensor body left room - from the economical point of view - to be optimized. After laboratory tests with the optimized sensor, a cast-in-situ bored pile has been built at the BAM Test Site Technical Safety in Horstwalde, South of Berlin. Additionally to the EFPI sensors, fiber Bragg grating (FBG) sensors, temperature sensors and resistance strain gauge (RSG) sensors are embedded in order to compare the signals with each other. In this paper, the modified sensor and the Setup of the cast-in-situ bored pile along with results of dynamic tests are shown. T2 - SHMII-5 - 5th International conference on structural health monitoring of intelligent infrastructure CY - Cancún, Mexico DA - 11.12.2011 KW - Fibre optic sensors KW - Monitoring KW - Concrete pile KW - Foundation KW - Integrity testing PY - 2011 IS - Topic_04.Cat_4.2-abs002 SP - 1 EP - 8 PB - National Autonomous University of Mexico CY - Mexico City AN - OPUS4-25142 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, Regina A1 - Maierhofer, Christiane A1 - Kreutzbruck, Marc A1 - Schilling, M. T1 - Numerical method of active thermography for the reconstruction of back wall geometry N2 - The paper presents numerical methods to detect and classify defects and inhomogeneities by means of active thermography. The objective is to determine the wall thickness of structure elements with an inaccessible back wall, for example, of pipes or Containers. As test specimens we used approximately 2 cm thick PVC samples with spatial variations in the back wall geometry. Flash lamps provided the heating. To know the thickness of the wall, we used two inversion methods and compared the results achieved. One is an iterative echo defect shape method and already tested on Steel test specimens with good reconstruction results. The second one is the Levenberg-Marquardt method, applied here to thermographic data for non-destructive testing. Since data capturing using active thermography and the presented numerical methods can easily be automated, the combination of these two procedures is a promising approach providing a broad area of application. T2 - 6th Workshop 'NDT in progress' CY - Prague, Czech Republic DA - 10.10.2011 KW - Impulse-thermography KW - Inversion KW - Levenberg-Marquardt method KW - Echo defect shape KW - Defect shape reconstruction PY - 2011 SN - 978-80-214-4339-6 IS - Chapter 8 SP - 245 EP - 252 AN - OPUS4-25144 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rahman, Mehbub-Ur A1 - Kolkoori, Sanjeevareddy A1 - Prager, Jens T1 - Elastische Wellenausbreitung in austenitischen Schweißnähten - numerische Simulationen und deren messtechnische Validierung N2 - In diesem Beitrag wird die numerische Modellierung und deren messtechnische Validierung der elastischen Wellenausbreitung in austenitischen Schweißnähten vorgestellt. Die Ultraschallprüfung von austenitischen Schweißverbindungen war und ist immer noch eine der schwierigsten Aufgaben der ZfP. Für eine optimierte Prüfkonfiguration ist es notwendig, verschiedene Prüfparameter wie Einschallwinkel, Prüfkopfposition und -Orientierung richtig einzustellen. Um die beste Anordnung zu ermitteln, wurde die Schallausbreitung in den austenitischen Schweißnähten mit verschiedenen Verfahren wie elastische finite Integrationstechnik (EFIT) und Raytracing simuliert. Mit Hilfe der Simulationsergebnisse wurde die verwendete Gruppenstrahlerprüftechnik optimiert. Es wurden zahlreiche Untersuchungen an anisotropen Testkörpern in V-Durchschallung und an bezüglich der Schweißnaht transversal orientierten Rissen durchgefühlt. Die Ergebnisse der auf Raytracing bzw. EFIT basierenden Simulationstools wurden untereinander und auch mit den Messergebnissen verglichen. T2 - DAGA 2011 - 37. Jahrestagung für Akustik - Fortschritte der Akustik CY - Düsseldorf, Deutschland DA - 21.03.2011 PY - 2011 SN - 978-3-939296-02-7 SP - 1 EP - 2 AN - OPUS4-25224 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völz, Uwe T1 - Visualisierung der Schallausbreitung in Festkörpern mit elektrodynamischen Sonden N2 - Die Prinzipien der Ultraschallausbreitung in festen Medien sind seit langem bekannt und können heute durch mathematische Modelle recht umfassend beschrieben und simuliert werden. In der Praxis zeigt sich aber, dass gerade bei komplexen Geometrien, sowie inhomogenen und anisotropen Materialien die Modelle immer noch an ihre Grenzen stoßen. Das ist insbesondere in der fehlenden Möglichkeit begründet, die akustischen Eigenschaften inhomogener Prüfgegenstände vollständig mathematisch zu beschreiben. Deshalb wird in letzter Zeit verstärkt nach Techniken gesucht, mit denen man die Schallausbreitung in solchen Materialien messen und anschaulich darstellen kann. Ziel dieser Entwicklung ist es, die Schallausbreitung in Festkörpern, insbesondere in solchen mit akustisch anisotropen Eigenschaften, besser zu verstehen und die Möglichkeit zu schaffen, die Simulationsrechnungen am realen Objekt zerstörungsfrei verifizieren zu können. In der Literatur werden verschiedene Methoden zur messtechnischen Visualisierung der Ultraschallausbreitung in Festkörpern beschrieben. Am bekanntesten sind optische Verfahren wie die Schlierentechnik, die schon seit langem genutzt wird, um den momentanen Schallfeldverlauf im Inneren von optisch transparenten Materialien sichtbar zu machen. Heute kommen verstärkt lasertechnische Methoden, wie z. B. das Laserinterferometer, zum Abtasten von nicht transparenten Materialoberflächen zum Einsatz. Da diese Verfahren mit einem hohen technischen Aufwand verbunden sind, werden häufig auch einfachere Methoden, wie z. B. das Abtasten mit punktförmigen piezoelektrischen Aufnehmern, verwendet. T2 - DAGA 2011 - 37. Jahrestagung für Akustik - Fortschritte der Akustik CY - Düsseldorf, Germany DA - 21.03.2011 KW - Ultraschall KW - Schallfeld KW - Elektrodynamische Sonde KW - Visualisierung PY - 2011 SN - 978-3-939296-02-7 SP - 347 EP - 348 PB - Deutsche Gesellschaft für Akustik CY - Berlin AN - OPUS4-25227 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rosemann, P. A1 - Bender, S. A1 - Heyn, Andreas A1 - Schmidt, J. T1 - Korrosion and Biokompatibilität beschichteter MgCa1,0 Magnesiumlegierungen N2 - Die Magnesiumlegierung Mg-Cal besitzt als potentielles bioabsorbierbares Implantatmaterial die Möglichkeit, vollständig vom menschlichen Körper absorbiert zu werden. Die mechanischen Kennwerte dieser Legierung liegen im Bereich des menschlichen Knochens und beide Legierungselemente (Mg, Ca) sind essentielle Spurenelemente im menschlichen Organismus. Der limitierende Faktor für den Einsatz ist die hohe Degradationsrate dieser Legierung. Um die Degradationsgeschwindigkeit zu verringern, wurden zwei Beschichtungssysteme auf Grundlage der Plasmachemischen Oxidation (PCO) und organischer Beschichtung erzeugt und untersucht. Das Korrosionsverhalten dieser Schichtsysteme wurde dabei mit dem Elektrochemischen Rauschen analysiert. Zusätzlich wurde der Einfluss von Wasserstoffentwicklung und eines ansteigenden pHWert auf die Zelltoxizität untersucht. Die Ergebnisse zeigen, dass eine Kombination von beiden Schichtsystemen zu einem viel versprechenden Degradationsverhalten führt. T2 - 14. Sommerkurs Werkstoffe und Fügen am Institut für Werkstoff- und Fügetechnik CY - Magdeburg, Germany DA - 23.09.2011 KW - Magnesium KW - Magnesium-Calcium KW - Implantat KW - Beschichtung KW - Plasmachemische Oxidation KW - Korrosion KW - Elektrochemisches Rauschen PY - 2011 SN - 978-3-940961-56-3 SP - 135 EP - 138 AN - OPUS4-24491 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, T. A1 - Heyn, Andreas A1 - Burkert, Annette A1 - Ebell, Gino T1 - Erfassung und Analyse der Startvorgänge lokaler Korrosion mittels kombinierter elektrochemischer und mikroskopischer Methoden N2 - Zur Untersuchung der Initiierungsvorgänge und dem Wachstumsverhalten lokaler Korrosionskeime auf nichtrostenden Stählen wurde eine neue elektrochemisch-mikroskopische Messmethode entwickelt. Bei dieser Messmethode wird durch Einsatz eines Echtfarben- Konfokalmikroskops mit Immersionsobjektiv das empfindliche elektrochemische Rauschmessverfahren um eine bildgebende Messkomponente erweitert. Ziel dieser Untersuchung war es, diskrete Rauschmesssignale visuell detektierbaren Korrosionserscheinungen auf der Stahloberfläche nahezu in Echtzeit zuzuordnen. Auf Grund der notwendigen Anforderungen an einen in situ Messaufbau wurde im Rahmen dieser Untersuchung ein neuartiges selbstklebendes Folienelektrodensystem, bestehend aus Gegen- und Bezugselektrode, entwickelt, das für die in situ Messung zum Einsatz kam. Die in situ Untersuchungen wurden an dem austenitischen Chrom-Nickel-Stahl 1.4301 durchgeführt. Als Ergebnis der Experimente konnten Stromtransienten im nA- bis μA-Bereich messtechnisch erfasst werden und mikroskopisch kleinen Korrosionskeimen, die sowohl stabil wie auch metastabil auf der Stahloberfläche auftraten, diskret und zeitnah zugeordnet werden. Weiterhin konnten mit Hilfe der Konfokaltechnik die Volumina und die Mantelflächen der einzelnen Lochdefekte ermittelt werden, sodass durch Auswertung und Kombination der elektrochemischen und mikroskopischen Messergebnisse erstmalig die Korrosionsstromdichte bestimmt werden konnte, die bei der Initiierung der lokalen Lochkeime aufgetreten ist. Damit konnte die Funktionalität und die hohe Empfindlichkeit des elektrochemisch-mikroskopischen Messverfahrens im Rahmen dieser Untersuchung erfolgreich verifiziert werden. T2 - 14. Sommerkurs Werkstoffe und Fügen am Institut für Werkstoff- und Fügetechnik CY - Magdeburg, Germany DA - 23.09.2011 KW - Lochkorrosion KW - Lochkeimbildung KW - Konfokalmikroskopie KW - In situ KW - Elektrochemie KW - Elektrochemisches Rauschen KW - Folienelektrode PY - 2011 SN - 978-3-940961-56-3 SP - 149 EP - 158 AN - OPUS4-24492 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmigalla, S. A1 - Heyn, Andreas T1 - Entwicklung einer Prüfmethode zur Untersuchung des Lochkorrosionsverhaltens von CMT-geschweißten Nickel-Basisplattierungen N2 - Höchstlegierte NiCrMo-Legierungen finden in weiten Bereichen der chemischen Industrie, der Offshoretechnik sowie in Rauchgasentschwefelungsanlagen Anwendung. Dabei werden an diese Werkstoffe höchste Anforderungen hinsichtlich der Korrosionsbeständigkeit gestellt. Neben der Verwendung von Vollmaterial gewinnt infolge gestiegener Rohstoffpreise die Applikation von auftraggeschweißten Plattierungen auf einem niedriglegierten Substratwerkstoff immer weiter an Bedeutung, wobei prinzipiell gegenüber den jeweiligen Walzwerkstoffen ein verschlechtertes Korrosionsverhalten der Plattierungen zu erwarten ist. Die Anwendung des CMT (Cold Metal Transferj-Prozesses bietet aufgrund eines geringen Wärmeeintrags gegenüber konventionellen Auftragschweißverfahren verfahrensspezifische Vorteile. Um eine unter Betriebsbedingungen ausreichende Korrosionsbeständigkeit zu gewährleisten, ist es erforderlich, ein Prüfverfahren zu entwickeln, welches den Einfluss der verschiedenen Verfahrensparametern auf das Lochkorrosionsverhalten exakt und reproduzierbar darstellen kann. Bisher bekannte Prüfmethoden, wie die Bestimmung kritischer Lochkorrosionstemperaturen durch Auslagerungsversuche in HCl-haltiger FeCf-Lösung oder die Aufnahme von Stromdichte-Potential-Kurven zur Bestimmung kritischer Lochkorrosionspotentiale, erweisen sich für die höchstlegierten Werkstoffe aus der Gruppe der NiCrMo-Legierungen als ungeeignet, da sich diese unter den gegebenen Bedingungen als lochkorrosionsbeständig erweisen. Somit kann der Einfluss der Schweißparameter während des Plattierprozesses auf das Lochkorrosionsverhalten mit den bislang bekannten Prüfverfahren nicht untersucht werden. T2 - 14. Sommerkurs Werkstoffe und Fügen am Institut für Werkstoff- und Fügetechnik CY - Magdeburg, Germany DA - 23.09.2011 KW - Korrosionsschutz KW - Plattierung KW - Nickelbasislegierung KW - CMT KW - Lochkorrosion KW - Korrosionsprüfung KW - Elektrochemisches Rauschen PY - 2011 SN - 978-3-940961-56-3 SP - 139 EP - 148 AN - OPUS4-24493 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Poltavtseva, M. A1 - Heyn, Andreas A1 - Boese, E. T1 - Mechanismen des Korrosionsschutzes plattierter Aluminiumwerkstoffe am Beispiel von Alclad 6025 N2 - Plattierte Aluminiumwerkstoffe sind qualitativ hochentwickelte Mehrschichtmaterialverbunde, die aus einer Kemlegierung und einer Plattierung bestehen. Das Kemmaterial erfüllt die Anforderungen an Festigkeit und Lebensdauer des Bauteils. Die Legierungen, die für Plattierungen verwendet werden, sorgen für den Korrosionsschutz unter meist atmosphärischen Bedingungen. Plattierte Aluminiumwerkstoffe finden vor allem Anwendung in der Luftfahrtkonstruktion oder wie Alclad 6025 im Bauwesen als Verkleidung von Fassaden und als Dacheindeckungen. In der Literatur wird der Korrosionsschutzmechanismus plattierter Aluminiumwerkstoffe allgemein als galvanischer Schutz beschrieben. Wenn eine Beschädigung der Plattierung bis zum Kern reicht, soll sich die elektronegativere Plattierung bevorzugt auflösen und damit die Kemlegierung schützen. Die Plattierungslegierung soll hinreichend korrosionsbeständig sein. Dabei kann eine leichte allgemeine Korrosion oder Lochkorrosion akzeptiert werden, allerdings mit einer geringen Tiefe, damit die Kernlegierung nicht korrodiert. Da jedoch keine detaillierten Angaben über den Schutzmechanismus in der Literatur gegeben werden, wurden am Beispiel von Alclad 6025 umfangreiche elektrochemische Untersuchungen sowie Auslagemngsversuche in verschiedenen Atmosphären bzw. Medien durchgeführt. Aus diesen Ergebnissen soll der Schutzmechanismus am Beispiel der Dachplattierung Alclad 6025 genauer beschrieben werden. T2 - 14. Sommerkurs Werkstoffe und Fügen am Institut für Werkstoff- und Fügetechnik CY - Magdeburg, Germany DA - 23.09.2011 KW - Plattierung KW - Aluminium KW - Alclad KW - Korrosionsmechanismus KW - Korrosionsschutz KW - Lochkorrosion KW - Korrosionsprüfung PY - 2011 SN - 978-3-940961-56-3 SP - 159 EP - 166 AN - OPUS4-24494 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kiefer, R. A1 - Boese, E. A1 - Heyn, Andreas A1 - Engelking, M. A1 - Hillert, R. T1 - Korrosion verchromter Kunstoffanbauteile unter verschärfter Streusalzbelastung mit CaCl2 N2 - Dekorativ verchromte Kunststoffanbauteile werden seit Anfang der 1970er Jahre in der Automobilindustrie eingesetzt, um einem Fahrzeug eine optisch höhere Wertigkeit zu geben. Diese mikroporig bzw. mikrorissig galvanisch abgeschiedenen Überzüge auf Kunststoffanbauteilen sind in einer festgelegten Reihenfolge übereinander angeordnet, um die Funktionen Dekorativität und Korrosionsbeständigkeit zu erfüllen. Unter dem Chromüberzug befindet sich u.a. ein Glanznickelüberzug, welcher durch Poren bzw. Risse bei Kontakt mit Streusalzsole gezielt korrodieren soll und somit den Chromüberzug kathodisch schützt. Der Zusatz von Kalziumchlorid in die Streusalzmischungen in Regionen mit extrem niedrigen Temperaturen (z. B. Winter in Moskau) stört diesen Mechanismus. Unter diesen Bedingungen wurden flächenhafte Schäden am Chromüberzug mikroporig verchromter Kunststoffanbauteile beobachtet. Bei Volkswagen erfolgte daraufhin die Umstellung aller verchromten Bauteile im Exterieur auf mikrorissig. Die Ursache für diese Schäden soll in der vorliegenden Arbeit geklärt werden. T2 - 14. Sommerkurs Werkstoffe und Fügen am Institut für Werkstoff- und Fügetechnik CY - Magdeburg, Germany DA - 23.09.2011 KW - Chrom-Nickel-Überzug KW - Streusalz KW - Calziumchlorid KW - Korrosionsschaden KW - Automobilbau KW - Korrosionsprüfung KW - Elektrochemie PY - 2011 SN - 978-3-940961-56-3 SP - 167 EP - 176 AN - OPUS4-24495 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pirskawetz, Stephan A1 - Rieffel, Y. A1 - Ruedrich, J. A1 - Plagge, R. A1 - Weise, Frank A1 - Siegesmund, S. A1 - Ruisinger, U. T1 - An inter-disciplinary model project to develop an innovative winter covering system N2 - Eight monumental sculptural groups made of Carrara marble are situated on the Schlossbrücke in the centre of Berlin in the periphery of the Museum Island, a Unesco world cultural heritage site. T2 - 14es journées d'étude de la SFIIC - Jardin de pierres - Conservation of stone in parks, gardens and cemetries CY - Paris, France DA - 22.06.2011 KW - Marble KW - Cultural heritage KW - Schlossbrücke KW - Protective winter cover KW - Deterioration KW - Numerical simulation PY - 2011 SN - 2-905430-17-6 SP - 122 EP - 131 AN - OPUS4-24368 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bettge, Dirk A1 - Klinger, Christian T1 - Schäden durch nichtmetallische Einschlüsse am Beispiel ICE 3 - Bedeutung und Lokalisierung einzelner nichtmetallischer Einschlüsse in großen Bauteilen N2 - Nichtmetallische Einschlüsse (NME) befinden sich in praktisch allen metallischen Bauteilen. Sie können auch unterhalb der Bauteiloberfläche als Starter von Schwingrissen fungieren. Besonders kritisch sind NME in oberflächennahen Bereichen in Bauteilen die großen Lastspielzahlen ausgesetzt sind. T2 - 37. VDI-Jahrestagung - Schadensanalyse - Produktverbesserung durch Schadensanalyse CY - Würzburg, Germany DA - 19.11.2011 KW - Schadensanalyse PY - 2011 SN - 978-3-18-092150-1 SN - 0083-5560 N1 - Serientitel: VDI-Berichte – Series title: VDI-Berichte VL - 2150 SP - 159 EP - 173 PB - VDI-Verl. CY - Düsseldorf AN - OPUS4-24685 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mishra, Kirti Bhushan A1 - Wehrstedt, Klaus-Dieter A1 - Schönbucher, A. T1 - Interpretations of temperature measurements in organic peroxide pool fires N2 - Most of the measurements of temperatures in large pool fires are indirect and present a number of complexities due to the interactions of convection, radiation and soot blockage. In the present work these influences for two organic peroxide [tert-butyl peroxybenzoate (TBPB) and tert-butyl peroxy-2-ethylhexanoate (TBPEH)] pool fires are analysed. Thermocouple measured temperature in the clear flame zone i.e. combustion zone are found to be 250-400 K lower than from the thermographic measurements. The convective and radiative heat flux contributions from the fire on temperature measurements are discussed. CFD (Computational Fluid Dynamics) simulations have been performed for large pool fires and the predicted time averaged flame temperatures were found to be in qualitative agreement with measurements due to the stoichiometric combustion model used in the present simulations. T2 - 5th European combustion meeting 2011 CY - Cardiff, UK DA - 28.06.2011 KW - Pool fire KW - Organic peroxides KW - TBPB KW - TBPEH KW - CFD KW - Temperature measurement PY - 2011 UR - http://www.uni-due.de/tchem/as/skripte/paper_mishra_et_al_cardiff_2011.pdf SP - 1 EP - 5 AN - OPUS4-24686 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schälike, Stefan A1 - Wehrstedt, Klaus-Dieter A1 - Schönbucher, A. T1 - CFD simulation to predict the thermal radiation of large LNG pool fires N2 - Flame temperature (T), surface emissive power (SEP) of Liquefied Natural Gas (LNG) pool fires (d = 1 m, 6.1 m, 30 m) are investigated by CFD (Computational Fluid Dynamics) simulation and compared with experimental results. Time averaged flame temperatures of T = 1320 K, T = 1298 K and T = 1281 K are obtained. Surface emissive power (SEP) of 55 kW=m2, 130 kW=m2 and 230 kW=m2 are predicted. T2 - 5th European combustion meeting 2011 CY - Cardiff, UK DA - 28.06.2011 KW - Pool fire KW - LNG KW - CFD KW - Thermal radiation KW - Surface emissive power PY - 2011 SP - 1 EP - 6 AN - OPUS4-24687 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ferrero, Fabio A1 - Kluge, Martin A1 - Schröder, Volkmar T1 - Numerical analysis of the effect of the electrode distance during the determination of the flammability limits of gases N2 - COMSOL Multiphysics® was used as a tool for the better understanding of the evolution of flow patterns during the induced ignition of gases. A simplified model was developed for the scope, by coupling the weakly compressible Navier Stokes module and the convection and conduction module. The current paper presents the results of the performed simulations. T2 - COMSOL Conference 2011 CY - Ludwigsburg, Germany DA - 26.10.2011 KW - Spark ignition KW - Gas flow KW - Temperature PY - 2011 SN - 978-0-9839688-0-1 N1 - Geburtsname von Kluge, Martin: Beckmann-Kluge, M. - Birth name of Kluge, Martin: Beckmann-Kluge, M. SP - 1 EP - 7 CY - Stuttgart AN - OPUS4-24700 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scholz, Christian A1 - Woydt, Mathias T1 - Highly stressable and low friction slip-rolling contacts through thin film coatings, uncoated, alternative steels or lubricants N2 - OEMs perceive diamond-like carbon (DLC) coatings as part of a strategy for low frictional tribosystems. Especially the automotive industry anticipates a benefit in applying such coatings in association with the lightweight construction of mechanical parts, for instance in gears and engines. In previous investigations it was shown, that DLC, amorphous carbon (a-C) and tetragonal amorphous carbon (ta-C) coatings can be slip-rolling resistant at least up to ten million load cycles at Hertzian contact pressures P0max of 2.9 GPa lubricated by engine oil at 120°C, Further improvements in load carrying capacity up to P0mean of 2.62 GPa (FN= 5,000 N) were achieved with alternative, available Steel metallurgies as Substrates for thin film coatings. Additional factors, such as influences of the lubrication on the surface chemistry (additives and base oils), wear and friction behavior were investigated. T2 - International tribology conference 2011 CY - Hiroshima, Japan DA - 30.10.2011 KW - Slip-rolling KW - Additives KW - DLC KW - ZrCN KW - High toughness steel KW - High pressure PY - 2011 IS - B4-08 SP - 1 EP - 1 AN - OPUS4-24702 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Döhler, M. A1 - Hille, Falk A1 - Mevel, L. A1 - Rücker, Werner ED - Chang, F.-K. T1 - Structural health monitoring during progressive damage test of S101 bridge N2 - For the last decades vibration based identification of damage on civil Engineering structures has become an important issue for maintenance operations on transport infrastructure. Research in that field has been rapidly expanding from classic modal Parameter estimation using measured excitation to modern operational monitoring. Here the difficulty is to regard to the specific environmental and operational influence to the structure under observation. In this paper, two methods accounting for statistical and/or operational uncertainties are applied to measurement data of a progressive damage test on a prestressed concrete bridge. On the base of covariance driven Stochastic Subspace Identification (SSI) an algorithm is developed to monitor and automatically compute confidence intervals of the obtained modal parameters. Furthermore, a null space based non-parametric damage detection method, utilizing a statistical χ2 type test is applied to the measurement data. It can be shown that for concrete bridges the proposed methodology is able to clearly indicate the presence of structural damage, if the damage leads to a change of the structural system. T2 - 8th International workshop on structural health monitoring 2011 CY - Stanford, CA, USA DA - 13.09.2011 KW - Subspace identification KW - Damage detection KW - Convidence intervals KW - Prestressed concrete bridge PY - 2011 SN - 978-1-60595-053-2 VL - 1 SP - 748 EP - 758 PB - DEStech Publications, Inc. AN - OPUS4-24688 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hille, Falk A1 - Döhler, M. A1 - Mevel, L. A1 - Rücker, Werner ED - De Roeck, G. ED - Degrande, G. ED - Lombaert, G. ED - Müller, G. T1 - Subspace-based damage detection methods on a prestressed concrete bridge N2 - For the last decades vibration based damage detection of engineering structures has become an important issue for maintenance operations on transport infrastructure. Research in vibration based structural damage detection has been rapidly expanding from classic modal parameter estimation to modern operational monitoring. Methodologies from control Engineering especially of aerospace applications have been adopted and converted for the application on civil structures. Here the difficulty is to regard to the specific environmental and operational influence to the structure under observation. A null space based damage detection algorithm is tested for its sensitivity to structural damage of a prestressed concrete road bridge. Specific techniques and extensions of the algorithm are used to overcome difficulties from the size of the structure which is associated with the number of recorded sensor channels as well as from the operational disturbances by a nearby construction site. It can be shown that for concrete bridges the proposed damage detection methodology is able to clearly indicate the presence of structural damage, if the damage leads to a significant change of the structural system. Small damage which do not result in a System change when not activated by loading, do not lead to a modification of the dynamic response behavior and for that cannot be detected with the proposed global monitoring method. T2 - EURODYN 2011 - 8th International conference on structural dynamics CY - Leuven, Belgium DA - 04.07.2011 KW - Subspace methods KW - Fault detection KW - Monitoring techniques KW - Concrete bridge PY - 2011 SN - 978-90-760-1931-4 IS - MS12 TUE 11:45 SP - 2304 EP - 2310 AN - OPUS4-24689 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stoppel, Markus A1 - Kurz, J.H. A1 - Taffe, Alexander A1 - Boller, C. ED - Chang, F.-K. T1 - Proactive condition assessment in civil engineering using automated multi-sensor systems N2 - Infrastructure is subject to continuous ageing. This has given life cycle management of infrastructure an increasing role. Reliable inspection and monitoring tools are therefore an increasing demand. A combination of different non-destructive test methods is often necessary to receive reliable results for material characterization, flaw detection and the determination of component specific geometry parameters. Regarding concrete structures thickness measurements are combined with flaw detection and additional information about reinforcement and tendon ducts is required. Therefore, a multi-sensor measurement approach is necessary with a high degree of automation. Otherwise a time consuming succession of manual measurements has to be performed which would prevent practical applications. A modular control and data acquisition approach is described and the application of two different automated measurement devices is shown. The BetoScan system consists of a self-navigating mobile robot. The system is especially designed for the investigation of reinforced concrete floors exposed to de-icing salts. The data acquisition of the OSSCAR system a multi-sensor scanner is similar to the robot approach. These different applications are based on a similar kernel allowing the modular use of different contact and noncontact sensors. The described general concept of multi-sensor data acquisition and data analysis presented here is not limited to the field of civil engineering applications. T2 - 8th International workshop on structural health monitoring 2011 CY - Stanford, CA, USA DA - 13.09.2011 KW - Multi sensor KW - Data acquisition KW - Assessment of concrete structures KW - Scanner KW - NDT PY - 2011 SN - 978-1-60595-053-2 VL - 2 SP - 2359 EP - 2366 PB - DEStech Publications, Inc. AN - OPUS4-24692 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thiele, Marc A1 - Baeßler, Matthias A1 - Rogge, Andreas A1 - Pirskawetz, Stephan ED - Rogge, A. ED - Meng, B. T1 - Schädigungsevolution in Beton unter hochzyklischen Ermüdungsbeanspruchungen N2 - Unter zyklischen Belastungen findet im Beton, wie bei anderen Materialien auch, ein Ermüdungsprozess statt. Im derzeitigen Erkenntnisstand zum Materialverhalten des heterogenen Betons gibt es gerade bei dessen Ermüdungsverhalten momentan noch viele nicht oder nicht ausreichend geklärte Fragestellungen. Deshalb befasst sich der vorliegende Beitrag mit der experimentellen Untersuchung des Ermüdungsverhaltens von Beton, speziell unter hochzyklischen Druckschwellbelastungen. Im Fokus der Untersuchungen stehen dabei die während der gesamten Lebensdauer im Materialgefüge ablaufenden Prozesse, die zu Veränderungen im Materialverhalten und schließlich auch bis zum Ermüdungsversagen führen können. Ziel ist es, eine möglichst realitätsnahe Beschreibung des im Materialgefüge ablaufenden Ermüdungsprozesses zu entwickeln. T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Germany DA - 07.11.2011 KW - Beton KW - Ermüdung KW - Schädigung PY - 2011 SN - 978-3-9814281-0-0 IS - E4 SP - 172 EP - 181 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-24724 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabe, Torsten A1 - Naghib Zadeh, Hamid A1 - Glitzky, C. A1 - Töpfer, J. T1 - Integration of Ni-Cu-Zn ferrite in LTCC-modules N2 - Integration of magnetic functional components in LTCC Circuit boards calls for co-firing of dielectric and ferrite tapes. Ni-Cu-Zn ferrites with permeability of p=900 were developed which can be fully densified at the Standard LTCC sintering temperature of 900 °C. Successful co-firing of this ferrite with dielectric tapes requires the adaptation of the shrinkage behavior of the materials as well as the thermal expansion during the cooling period - especially in the temperature range below the transformation point of the glassy phase of the dielectric tape. To match these preconditions, a new dielectric LTCC material with steep sintering curve and high thermal expansion coefficient was designed. Sintered multilayer composed of Ni-Cu-Zn ferrite and tailored dielectric tapes are free of cracks and possess no open porosity. No significant interdiffusion between the ferrite and dielectric tapes was found by EDX measurements. Compared to pure ferrite laminates the permeability of co-sintered Ni-Cu-Zn ferrite layers is drastically reduced to 400, i.e. a decrease of more than 50 %. To investigate the origin of this permeability reduction, Ni-Cu-Zn ferrite laminates were sintered separately, and in combination with alumina release tapes or dielectric tapes, respectively. SEM and EDX analysis of co-fired laminates reveal differences in the ferrite grain growth behavior. Ferrite laminates with homogeneous microstructure and grain size up to 50 pm exhibit large permeability. However, growth of ferrite grains does not take place near the interface between ferrite and release or dielectric tapes. There is a strong correlation between high permeability and volume fraction of large ferrite grains. Regions of fine and coarse grains inside the ferrite layers show different bismuth concentration; the Bi-content is larger in regions of fine ferrite grains. T2 - CICMT 2011 - 7th International conference and exhibition on ceramic interconnect and ceramic microsystems technologies CY - San Diego, CA, USA DA - 05.04.2011 KW - LTCC KW - Co-firing KW - Ferrite KW - Shrinkage behavior KW - Constrained sintering KW - Keramische Multilayer KW - Grenzflächenreaktion PY - 2011 SN - 0-930815-92-0 SP - 000266 EP - 000275 PB - IMAPS, International Microelectronics and Packaging Society AN - OPUS4-25072 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grasse, Fabian A1 - Trappe, Volker A1 - Thöns, Sebastian A1 - Said, Samir ED - De Roeck, G. ED - Degrande, G. ED - Lombaert, G. ED - Müller, G. T1 - Structural health monitoring of wind turbine blades by strain measurement and vibration analysis N2 - Wind turbine blades have to withstand a high number of load cycles in mostly hard weather conditions over 20 years. In a research project BAM and several partners have designed, evaluated and tested a condition monitoring system for all parts of a wind turbine. At a rotorblade with a length of 58 m fibre bragg grating sensors were applied for in-service strain measurement. Additionally a complex test rig was designed to enable real biaxial loading conditions at a representative test rotor blade to simulate the mechanical loading conditions in the lab. In this test blade with a length of 8 m also fibre bragg grating sensors were implemented to determine their influences for the structure and the condition monitoring system. Vibration measurements were carried out at different test phases. The results were compared with finite element strain and modal analysis. T2 - EURODYN 2011 - 8th International conference on structural dynamics CY - Leuven, Belgium DA - 04.07.2011 KW - Rotor blade KW - Test blade KW - Modal analysis KW - Condition monitoring PY - 2011 SN - 978-90-760-1931-4 IS - MS25 Tue SP - 3490 EP - 3497 AN - OPUS4-25076 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schurig, Michael A1 - Klinger, Christian A1 - Schöne, Dieter A1 - Bork, Claus-Peter A1 - Klingbeil, Dietmar ED - Christ, H.-J. ED - Berger, C. T1 - Very high cycle fatigue testing on an electrodynamic shaker system N2 - Fatigue testing in the VHCF ränge requires testing machines with increased frequencies. However, application of energy-saving resonance testing leads to a linkage between test frequency and specimen Parameters. The frequency ränge and the available forces of the testing machine are limiting possible specimen dimensions. Electrodynamic shakers combine test frequencies up to 4000 Hz with forces in the kN range. Thus, a relatively wide range of tests is possible which allows studying the influence of specimen size on VHCF behaviour. Electrodynamic shakers as well as the respective Computer control Systems and Vibration measurement techniques are well established in scientific and technical applications. We present results of a first study of VHCF testing on electrodynamic shakers conducted at BAM. Test frequency, specimen size and stress levels have been varied. One goal is to balance the needs of materials testing with the Standard test Systems of environmental Simulation to provide a powerful and flexible tool for very high cycle fatigue testing. Further investigation to optimize the technique is required. T2 - VHCF5 - 5th International conference on very high cycle fatigue CY - Berlin, Germany DA - 28.06.2011 KW - Electrodynamic shaker KW - Resonance testing KW - Variable frequency KW - Envrionmental simulation KW - Specimen size KW - Two-degree-of-freedom system KW - VHCF KW - Shaker KW - Elektrodynamisch KW - Prüfung PY - 2011 SN - 978-3-9814516-0-3 SP - 433 EP - 438 AN - OPUS4-25067 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ohm, Katrin A1 - Baer, Wolfram ED - Grellmann, W. T1 - Einfluss der Verfahrenstechnik und der Werkstoffprüfung auf den im Zugversuch zu ermittelnden Verformbarkeitskennwert Agt von Betonstählen N2 - Die Streuung der Agt-Werte von Betonstahl bleibt durch die Variation der Prüfbedingungen (Temperatur, Geschwindigkeit) innerhalb der prüfnormseitig zulässigen Grenzen weitgehend unbeeinflusst. Gleichzeitig führt die Variation der Prüfbedingungen zu einer signifikanten, für die Produktabnahme relevanten Änderung des Niveaus von Agt. Die Auswertemethodik des Zugversuches (Festlegung der Höchstkraft, Wahl des Verfahrens zur Agt-Bestimmung) hat einen signifikanten Einfluss auf Niveau und Streuung von Agt. Es werden Empfehlungen zur Minimierung der Streuung von Agt gegeben. T2 - DVM-Tagung Werkstoffprüfung 2011 - Neue Entwicklungen in der Werkstoffprüfung - Herausforderungen an die Kennwertermittlung CY - Berlin, Germany DA - 01.12.2011 KW - Betonstahl KW - Zugversuch KW - Gesamtdehnung bei Höchstkraft KW - Kennwertstreuung KW - Prüfmethodik KW - Reinforcing steel KW - Tensile test KW - Percentage total extension at maximum force KW - Scatter of results KW - Test method PY - 2011 SN - 978-3-9814516-1-0 SN - 1861-8154 N1 - Serientitel: DVM-Bericht – Series title: DVM-Bericht IS - 643 SP - 279 EP - 284 AN - OPUS4-25068 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jakubcová, Petra A1 - Rübner, Katrin A1 - Schnell, A. T1 - Leichte Gesteinskörnungen auf der Basis thermisch und hydrothermal hergestellter Blähgranulate aus Abbruchabfällen N2 - Beton mit leichten Gesteinskörnungen (Leichtzuschlägen) ist seit dem Altertum bekannt. Leichte Gesteinskörnungen vulkanischen Ursprungs wurden bereits zur Errichtung der Maya-Pyramiden in Mexiko und von monumentalen Bauwerken im Römischen Reich verwendet. Zu den berühmtesten Beispielen der ersten Anwendung von Leichtbeton in Europa gehören das Kolosseum und das Pantheon in Rom, Hier wurden sowohl natürliche als auch künstliche Zuschlagstoffe, wie Bims, Lava und zerkleinerter Ziegelsplitt, benutzt. Mit steigender Nachfrage nach leichten Gesteinskörnungen und einer weltweit begrenzten Verfügbarkeit natürlicher Leichtzuschläge wurden synthetische leichte Gesteinskörnungen entwickelt. Ihre großtechnische Herstellung begann nach dem Ersten Weltkrieg. Heute werden leichte Gesteinskörnungen in einem breiten Schüttdichtespektrum von 100 bis 1200 kg/m3 hergestellt. Sie stellen einen wichtigen Teil der Gesteinskörnungen in der Baubranche dar. T2 - 15. Seminar 'Beschichtungen und Bauchemie' - Reaktive und filmbildende organische Bindemittel: Der Klimawandel und der Einfluss auf die Rezepturen Teil II CY - Kassel, Germany DA - 29.11.2011 KW - Sekundärrohstoffe KW - Sekundäre Gesteinskörnung KW - Recycling KW - Leichtbeton PY - 2011 SP - 55 EP - 66 AN - OPUS4-25086 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gründer, Klaus-Peter A1 - Köppe, Enrico A1 - Kadoke, Daniel T1 - Optische 3D-Referenzierung eines funkgestützten Multisensorsystems zur Bewegungsanalyse gefährdeter Personen N2 - Ein stereo-fotogrammetrisches Messverfahren wurde zur quantitativen Analyse der Bewegungssignale eines elektrischen Multi-Sensorsystems eingesetzt. Der Vergleich von Weg- und Winkel-Zeitverläufen zeigte bereits eine recht gute Übereinstimmung, verdeutlichte jedoch auch die Notwendigkeit einer weiterzuentwickelnden Kalibriermethodik. Die Stereo-Videogrammetrie hat sich als Referenzverfahren zur Analyse und Validierung dreidimensional ausgelegter elektrischer Bewegungssensorik für den Nahbereich bewährt. T2 - 3D-NordOst 2011 - 14. Anwendungsbezogener Workshop zur Erfassung, Modellierung, Verarbeitung und Auswertung von 3D-Daten CY - Berlin, Germany DA - 08.12.2011 KW - Stereo-Videogrammetrie KW - Funkgestützte Sensorik KW - Bewegungsanalyse PY - 2011 SN - 978-3-942709-03-3 SP - 33 EP - 38 AN - OPUS4-25103 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weltschev, Margit A1 - Niebergall, Ute T1 - Comparison of the material parameters of polyethylene grades with the test performance behaviour of packagings for the transport of dangerous goods in dependence on the pre-storage time with 55% nitric acid N2 - The material parameters melt flow rate MFR, density D, notched impact strength N.I.S. at -30 °C, stress crack resistance FNCT and resistance to oxidative degradation Ox (determined by the increase of MFR) have been selected for a comparison of polyethylene grades for one design type in the “European Standard EN 15507 - Transport packaging for dangerous goods - Comparative material testing of polyethylene grades”. The parameters have a systematic relationship with design type tests. The notched impact strength at -30 °C and the resistance to oxidative degradation of polyethylene grades determined with test specimens of compression moulded sheets are directly comparable with drop tests at -18 °C of design types produced of these grades after pre-storage with 55 % nitric acid for 21 days at 40 °C. The impact of the pre-storage time of jerricans with 55 % nitric acid at 40 °C and 23 °C on the marginal drop heights in drop tests at -18 °C, on the MFR and on the tensile properties tensile strength, breaking elongation and the elastic modulus were investigated. Packaging design types (jerricans) made of three polyethylene grades from different producers were pre-stored with 55 % nitric acid for 21,42 and 84 days at 40 °C as well as for six months at 23 °C. The MFR and tensile properties of test specimens taken from the design type side walls as well as the marginal drop heights of the jerricans in drop tests at -18 °C were determined. The values of the notched impact strength at -30 °C of polyethylene grades are not comparable with the marginal drop heights determined in drop tests at -18 °C. The oxidative damaging impact of nitric acid has a greater effect on the grade with lower resistance to oxidative degradation by reducing more significantly the marginal drop heights with increasing pre-storage time. Pre-damage with 55 % nitric acid for 21 days at 40 °C, as recommended in ISO 16101 and EN 15507 caused an increase in the marginal drop heights of most design types in drop tests when compared with design types without pre-damage. The test results demonstrated clearly that pre-storage of the jerricans for six months at 23 °C caused a higher increase in the MFR and lower marginal drop heights of the jerricans in drop tests at -18 °C compared with pre-storage of the jerricans for 21 days at40 °C. The mechanical properties change as a result of diffusion of nitric acid into the polyethylene grades and the reaction of the nitric acid with the polymers. The percentage decrease and increase in the tensile strength, breaking elongation and elasticity modulus of test specimens taken from the design type side walls after different pre-storage times were only partly comparable with the marginal drop heights in drop tests at -18 °C. T2 - EUROCORR 2011 - Developing solutions for the global challenge CY - Stockholm, Sweden DA - 04.09.2011. KW - Gefahrgutverpackungen KW - Polyethylenformstoffe KW - Baumusterprüfungen KW - Nachweis der chemischen Verträglichkeit KW - Oxidativer Abbau PY - 2011 SP - 1 EP - 12 AN - OPUS4-24346 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Liehr, Sascha A1 - Krebber, Katerina ED - De Roeck, G. ED - Degrande, G. ED - Lombaert, G. ED - Müller, G. T1 - A novel quasi-distributed long-gauge fiber optic strain sensor system for dynamic measurement N2 - We present a novel technique based on incoherent optical frequency domain reflectometry (OFDR) to measure length changes quasi-distributed between reflection points in optical fibres. The technique enables length changes to be measured with a resolution better than 1 µm and allows for static and dynamic measurement capabilities up to 2 kHz. We demonstrate that dynamic measurements of multiple fibre sections can be conducted independently from each other with high precision. Due to the precise and dynamic measurement capabilities, the proposed sensor system is expected to open new fields of application, especially in the structural-health-monitoring sector. Possible applications are discussed in the paper. T2 - EURODYN 2011 - 8th International conference on structural dynamics CY - Leuven, Belgium DA - 04.07.2011 KW - Distributed sensor KW - Strain sensor KW - Optical fiber sensor KW - Structural health monitoring KW - OFDR KW - Length change measurement KW - Dynamic sensor PY - 2011 SN - 978-90-760-1931-4 SP - 2097 EP - 2102 AN - OPUS4-24347 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hothan, Sascha A1 - Ehlig, D. ED - Ortlepp, R. ED - Curbach, M. T1 - Hochtemperaturverhalten von Stahlbetonplatten mit Textilbetonverstärkung N2 - Die Verwendung von Endlosfilamenten aus Carbon als Be-wehrungsmaterial für Beton, sogenannter Textilbeton, bietet die Möglichkeit der Sanierung und der Verstärkung bestehender Stahlbetonkonstruktionen. Dabei muss die Frage nach dem Feuerwiderstand von derart verstärkten Tragwerken be-antwortet werden. Aufschluss darüber liefern Brandversuche. Mit Textilbeton verstärkte Stahlbetonplatten haben in Brandversuchen nach der Einheits-Temperaturzeitkurve bei 33 % der Traglast mehr als 60 Minuten standgehalten. Bei 50 % der Traglast kam es nach einer Branddauer von 55 Minuten, bei 65 % nach 30 Minuten, zu einem Zugversagen der textilen Verstärkungsschicht. Bei während des Brandes unbelasteten bzw. gering belasteten Platten lagen die im Anschluss ermittelten Resttragfähigkeiten bei 65 % der Bruchlast nach 30 Minu-ten Branddauer bzw. bei 50 % der Bruchlast nach 60 Minuten Branddauer. Wäh-rend und nach der Beflammung waren zunehmende Durchbiegungen und Rissbreiten erkennbar. Es traten aber keine Abplatzungen auf, weshalb die Ver-stärkungsschicht aus Textilbeton als zusätzliche Betondeckung für die Stahlbe-wehrung angerechnet werden kann. Diese außerordentlich positiven Ergebnisse zeigen, dass für verstärkte Konstruktionen Feuerwiderstandsklassen von F60 bzw. R60 ohne zusätzliche Maßnahmen erreicht werden können. Dies ist von ho-her Relevanz für die wirtschaftliche Anwendung dieser Verstärkungsmethode. Für ein umfassendes Verständnis der Interaktion zwischen den Bewehrungen Textil und Stahl sowie der Versagensmechanismen während des Brandes, sind weitere Erkenntnisse über die mechanischen Eigenschaften von Textilbeton im Hochtemperaturbereich nötig. Auch der Einfluss der Oxidation des Carbons konnte nicht abschließend beurteilt werden. 354 HOTHAN und EHLIG: Hochtemperaturverhalten von Stahlbetonplatten mit TRC-Verstärkung Summary: Using endless carbon filaments for concrete reinforcement, so called textile reinforced concrete, the possibility of reconstruction and strengthening of existing concrete structures arises. The question concerning fire resistance of structures strengthened like this has to be answered. Fire tests provide answers. Steel reinforced concrete slabs strengthened with textile reinforced concrete load-ed with 33 % of ultimate load survived an ISO-fire for 60 minutes. Loaded with 50 % and 65 % of ultimate load the slabs failed after 55 minutes and 30 minutes of fire exposure due to tension failure of the textile reinforcement layer. Slabs not loaded or with a low load level during fire exposure showed remaining bearing resistances of 65 % of ultimate load after 30 minutes and 50 % of ultimate load after 60 minutes of fire exposure. During and after fire exposure rising deflec-tions and growing crack widths were observed. However no spalling occurred. Therefore the textile reinforced concrete layer can be taken into account as con-crete covering for the steel reinforcement. Those extraordinary positive results document, that reinforced concrete structures with additional fibre reinforced concrete can achieve fire resistance classes of R60 without additional provisions. To achieve comprehensive understanding of interaction between steel and fibre reinforcement and failure mechanisms in case of fire more knowledge concerning the mechanic properties of fibre reinforced concrete at high temperatures is es-sential. The influence of oxidation of the carbon fibres could not fully be an-swered. T2 - 6. Kolloquium zu textilbewehrten Tragwerken (CTRS6) CY - Berlin, Germany DA - 19.09.2011 KW - Feuerwiderstand KW - Abplatzen KW - Textilbeton KW - Brandbeanspruchung KW - Biegebelastung PY - 2011 SN - 978-3-86780-245-1 SP - 353 EP - 367 AN - OPUS4-24635 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ehlig, D. A1 - Hothan, Sascha ED - Koenders, E.A.B. ED - Dehn, F. T1 - Reinforced concrete slabs strengthened with textile reinforced concrete subjected to fire N2 - Thin layers of textile reinforced concrete (TRC) can be used as strengthening for reinforced concrete (RC) slabs or beams to increase their foad-bearing capacity. The concrete matrix consists of a fine-grained concrete with a thickness of 8 to 15 mm. Information on the behaviour of strengthened structures subjected to fire is of particular inlerest for practical applications of this innovative construction method. A total of 7 RC slabs with Steel reinforcement were produced: 2 slabs were used as reference and 5 slabs were strengthened with three layers of textile reinforcement. Ultimate capacity of reference slabs and particular TRC strengthened slabs was determined from statie load results fom 4-point-bending tests. Fire tests on these slabs were carried out with utilization fectors using a Standard temperature curve (ISO-834-1) for fire testing. Test loads varied between 0 % and 65 % ofuMmate load. To detect temperatures during fire exposure thermocouples were arranged throughout the cross-section of the slabs. Depending on the utilization the slabs were exposed to fire for 30 minutes or for 60 minutes. In some cases bending fäilure occurred, in other cases the slabs survived. None of the specimens exhibited any visual damage or concrete spalling during fire exposure. Results of deformation measurements and residual strength measurements are presented. Even though mechanisms are not fifily understood, it is important to discuss the presumable reasons for the surprisingiy positive test results. It is presumed tbat the key mechanisms contributing to the outstanding fire resistance capability presented are: superior crack control of the TRC and load redistribution between textile and Steel reinforcement as well as the primary load transfer directly into the slabs. T2 - 2nd International RILEM workshop on concrete spalling due to fire exposure CY - Delft, The Netherlands DA - 05.10.2011 KW - Textile reinforced concrete KW - Fine-grained concrete KW - Carbon fibres KW - Bending load KW - Fire exposure PY - 2011 SN - 978-2-35158-118-6 VL - PRO 80 SP - 419 EP - 426 PB - RILEM Publications AN - OPUS4-24636 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Scholz, Christian A1 - Spaltmann, Dirk A1 - Woydt, Mathias T1 - Höchstbelastbare Wälzkontakte mit geringer Misch-/Grenzreibungszahl N2 - Leichtbaustrategien im Antriebsstrang erhöhen durch Downsizing die Hertz’schen Kontaktpressungen und die mechanischen Lasten. Dadurch müssen neben wälzbeständigen Stählen auch dazu passende reibungsmindernde Konzepte gefunden werden, in der vorliegenden Arbeit wurden alternative, hoch zähe Stähle mit einer Wälzbeständigkeit bis Pomax = 4,2 GPa untersucht, welche mit geeigneten Grundöl- und Additivkombinationen die Reibungszahlen herunter auf 0,025 reduzieren konnten. Diese alternativen Stahllegierungen erlauben nicht nur an der Zahnflanke sehr hohe Kontaktpressungen, sie bieten außerdem entsprechende Zähigkeits- und Festigkeitseigenschaften für den Zahnfuß. In vorangegangenen Untersuchungen wurde eine Vielzahl verschiedener Dünnschichten auf ihre Überrollbeständigkeit unter Extrembeanspruchungen validiert. Allerdings zeigte sich bei den meisten Dünnschichten ein Qualitätsunterschied von Charge zu Charge. Unter Verwendung verschiedener organischer, metallorganischer und anorganischer Additive konnten, sich daran anschließende Versuche, vielversprechende Ergebnisse erzielt werden. Sämtliche Versuche unter extremen Beanspruchungen wurden bei +120°C Öltemperatur auf Zwei-Scheiben-Tribometern vom Typ AMSLER und 2Disk von Optimol Instruments unter Misch-/Grenzreibungsbedingungen durchgeführt und die tribologischen Eigenschaften der neuartigen, unbeschichteten Stähle und in Relation zu leistungsstarken DLC-/ZrCN Dünnschichten gesetzt. T2 - 52. Tribologie-Fachtagung - Reibung, Schmierung und Verschleiß - Forschung und praktische Anwendungen CY - Göttingen, Deutschland DA - 26.09.2011 KW - Hochzähe Stähle KW - DLC KW - ZrCN KW - Dünnschichten KW - Extrembeanspruchung KW - Polyglykole KW - Additive PY - 2011 SN - 978-3-00-035439-7 VL - I SP - 11/1 EP - 11/16 AN - OPUS4-24611 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vila-Comamala, J. A1 - Diaz, A. A1 - Guizar-Sicairos, M. A1 - Gorelick, S. A1 - Guzenko, V.A. A1 - Karvinen, P. A1 - Kewish, C.M. A1 - Färm, E. A1 - Ritala, M. A1 - Mantion, Alexandre A1 - Bunk, O. A1 - Menzel, A. A1 - David, C. ED - Morawe, C. ED - Khounsary, A.M. ED - Goto, S. T1 - Characterization of a 20-nm hard X-ray focus by ptychographic coherent diffractive imaging N2 - Recent advances in the fabrication of diffractive X-ray optics have boosted hard X-ray microscopy into spatial resolutions of 30 nm and below. Here, we demonstrate the fabrication of zone-doubled Fresnel zone plates for multi-keV photon energies (4-12 keV) with outermost zone widths down to 20 nm. However, the characterization of such elements is not straightforward using conventional methods such as knife edge scans on well-characterized test objects. To overcome this limitation, we have used ptychographic coherent diffractive imaging to characterize a 20 nm-wide X-ray focus produced by a zone-doubled Fresnel zone plate at a photon energy of 6.2 keV. An ordinary scanning transmission X-ray microscope was modified to acquire the ptychographic data from a strongly scattering test object. The ptychographic algorithms allowed for the reconstruction of the image of the test object as well as for the reconstruction of the focused hard X-ray beam waist, with high spatial resolution and dynamic range. This method yields a full description of the focusing performance of the Fresnel zone plate and we demonstrate the usefulness ptychographic coherent diffractive imaging for metrology and alignment of nanofocusing diffractive X-ray lenses. T2 - SPIE Optics and photonics CY - San Diego, USA DA - 20.08.2011 KW - X-ray imaging KW - Diffractive X-ray optics KW - Electron beam lithography KW - Ptychographic coherent diffractive imaging PY - 2011 DO - https://doi.org/10.1117/12.893235 SN - 0277-786X N1 - Serientitel: Proceedings of SPIE – Series title: Proceedings of SPIE VL - 8139 SP - 81390E-1 EP - 81390E-7 AN - OPUS4-24613 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute A1 - Bredow, Andrea A1 - Berger, Wolfgang A1 - Wessel-Bothe, Stefan A1 - Keller, T. T1 - Optimierung des Säulenperkolationsverfahrens durch Automatisierung N2 - Elutionstests im Labormaßstab werden zur Ermittlung der Freisetzung von Schadstoffen aus Böden oder mineralischen Abfällen für die Verwertung in technischen Erdbau-werken durchgeführt. Sie sollen die Feldbedingungen möglichst realitätsnah wider-spiegeln und auch die Beurteilung der Freisetzung von Schadstoffen über längere Zeiträume ermöglichen. Aus diesem Grunde werden im Entwurf der novellierten BBodSchV neue Verfahren zur Eluatgewinnung aus den genannten Materialien festgeschrieben. T2 - DBG-Jahrestagung, Kommission VI, 'Böden verstehen - Böden nutzen - Böden fit machen' CY - Berlin, Germany DA - 03.09.2011 KW - Schadstofffreisetzung KW - Säulenperkolation KW - Werkstoffauswahl KW - Elutionsverfahren PY - 2011 UR - http://eprints.dbges.de/565/1/Berichte_der_DBG_Kalbe_2753.pdf SP - 1 EP - 4 AN - OPUS4-24648 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Berger, Wolfgang A1 - Kalbe, Ute A1 - Krüger, Oliver A1 - Litzba, Andreas T1 - Vergleich der Ergebnisse von Übereinstimmungstests bei Säulen- und Schüttelversuchen N2 - In der Bundes-Bodenschutz- und Altlasten-verordnung (BBodSchV) und im Arbeits-entwurf der Novellierung ist für den Wirkungspfad Boden-Grundwasser eine Sickerwasserprognose vorgesehen, um die Gefahren, die von kontaminierten Stand-orten für das Schutzgut Grundwasser ausgehen, beurteilen zu können. Bei der Sickerwasserprognose kann u.a. auf der Grundlage von Materialuntersuchungen im Labor die Quellstärke kontaminierter Ma-terialen ermittelt werden, welche dann bei Transportmodellierungen Berücksichtigung findet. Der Entwurf der Novellierung der BBodSchV sieht für die Ermittlung der Quellstärke den Übereinstimmungstest des Säulenversuchs nach DIN 19528 bis zu einem Wasser/Feststoff - Verhältnis (W/F) von 2 l/kg für anorganische und organische Stoffe (PAK) oder den Schüttelversuch nach DIN 19529 für anorganische Stoffe und E DIN 19527 für organische Stoffe auch jeweils mit einem W/F von 2 l/kg vor. Die Zulassung beider Elutionsverfahren setzt die Gleichwertigkeit der Ergebnisse beider Verfahren voraus. Im Folgenden werden die Ergebnisse des Vergleichs der Auslaugung von polyzyklischen aromat-ischen Kohlenwasserstoffen (PAK) aus unterschiedlichen Böden mit Hilfe beider Elutionsverfahren vorgestellt. T2 - DBG-Jahrestagung, Kommission VI, 'Böden verstehen - Böden nutzen - Böden fit machen' CY - Berlin, Germany DA - 03.09.2011 KW - Elutionsverfahren KW - Übereinstimmungstest KW - Säulenverfahren KW - Schüttelverfahren KW - Kontaminierte Böden KW - Polyzyklische aromatische Kohlenwasserstoffe (PAK) PY - 2011 UR - http://eprints.dbges.de/551/1/Berichte_der_DBG_Berger3376.pdf SP - 1 EP - 2 AN - OPUS4-24649 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, Wolfgang A1 - Schukar, Vivien A1 - Kusche, Nadine T1 - Calibration facility for quality certification of surface-attached fiber optic and electrical strain sensors N2 - Strain measurement in structures witli the purpose of long-term structurai health inonitoring must provide reliable inforination about the structure’s behavior over the whole period of use. The user must be sure that installed sensors are validated and work to the utmost satisfactiou. For this purpose, sensor Systems are tested using special facilities. Bccause it is not easy to characterize the strain transfer quality from the host structure into surface-applied strain sensors, a unique testing facility has been developed. Originally developed for fiber Bragg grating based sensors, the KALFOS facility (= calibration of fiber optic sensors) can also be used for electrical strain sensors. Calibration ineasurements are referenced by unbinsed Digital Image Correlation (D1C) and Electronic Speckle Pattern Interferometer (ESPI) methods. The strain transfer behavior can experimentally be analyzed and investigated under combined thermal and mechanical loading conditions and allows revealing wealuiesses in couimonly used attachment methodologies. The deformation of all members (particularly the coating/substrate - adhesive combination) in the sensing area is physically independently gained and recorded. Results achievcd allow precise description of the strain transfer function, Validation of the longterm strain sensor characteristics, matching of specific measurement requirements with environmental conditions, and, moreover, the verification of Standards for use of strain sensors. T2 - IEEE Sensors 2011 conference CY - Limerick, Ireland DA - 28.10.2011 KW - Fibre optic sensors KW - Structural health monitoring KW - Validation KW - Strain sensor KW - Surface application reliability PY - 2011 SN - 978-1-4244-9288-6 DO - https://doi.org/10.1109/ICSENS.2011.6127253 SP - 1337 EP - 1340 AN - OPUS4-24655 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, Wolfgang A1 - Schukar, Vivien A1 - Tkachenko, Viktoriya T1 - How do application-related issues influence the reliability of fiber optic strain measurements? N2 - Fibre optic strain sensors are increasingly used and sensor systems are provided with specifications. Even if the performance is well specified, the strain characteristics of the sensor, strain transfer factor, mechanical stability under thermal influences, the performance of applied strain sensors can seriously differ from virgin sensor's the performance. The contribution will focus on issues that can deteriorate the sensor function or reduce the reliability of measurement results. Aspects are considered how to come to reliable strain measurements and how to validate strain measurements of applied sensors. Related to this topic, European activities like the recently started European COST TD1001 action, called (OfSeSa) will be presented. T2 - IEEE Sensors 2011 conference CY - Limerick, Ireland DA - 28.11.2011 KW - Fibre optic sensors KW - Structural health monitoring KW - Validation KW - Strain sensor KW - Surface application reliability PY - 2011 SN - 978-1-4244-9288-6 SP - 947 EP - 950 AN - OPUS4-24656 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - von der Ehe, Kerstin A1 - Jaunich, Matthias A1 - Wolff, Dietmar T1 - UHMW-PE - a shielding material with special properties influenced by radiation N2 - Ultra high molecular weight polyethylene (UHMW-PE) - due to its high hydrogen content - is used as neutron shielding material in casks for storage and transport of radioactive materials. Besides this, UHMW-PE - as a high-performance polymer - has been used for several years in medical technology due to its excellent slip and wear properties. Due to the special properties of UHMW-PE which result basically from its extreme chain lengths and its high degree of crystallinity, it is predestinated for the aforementioned applications. In both cases, irradiation and its impact on the molecular structure of polyethylene play an important role. In the first case, irradiation exists as a by-product of inserting the radioactive material in the cask. Hence PE has to withstand any type of degradation affecting safety relevant aspects to be applicable for long term radiation shielding purposes for instance over a period of 40 years. In the second case irradiation is applied deliberately for purposes such as sterilization and crosslinking, leading to partial improvement of the mechanical properties (e.g. fracture toughness, crack propagation resistance, wear resistance) and better Chemical stability. Specifically concerning their use in the field of medical technology, different types of UHMW-PE have been objects of numerous publications. It is generally accepted that two parallel and competitive processes, based on chain scission and reactions of Ccentered radicals and molecular fragments, occur in PE as a consequence of radiation: radical recombination accounts for crosslinking, together with some disproportionation, formation of low molecular weight fragments, and recrystallization. Furthermore, formation of oxygenated structures in the presence of traces of oxygen is an antagonist of the C-centered radicals. Radiation induced scission preferentially takes place in the amorphous phase and noncrystalline surface of the crystals. It is followed by folding of molecular fragments, crystallinity growth and increased perfection in the crystal lamellae [4, 5]. Chain scission results in shorter polymer molecules, fewer entanglements, and consequently, increased molecular mobility. The scope of our investigation comprises an estimation of the radiation and thermal impact on the molecular and supra molecular structure of the two types of PE used for neutron shielding cask components. A further point which is worth to explore is to what extent these changes are detectable by thermo-analytical (TA) methods, such as Differential Scanning Calorimetry (DSC), Thermo Mechanical Analysis (TMA), Dynamic Mechanical Analysis (DMA) and Thermogravimetry (TG). Additionally FT-IR and solubility measurements have been performed. In our studies we focused on the UHMW-PE material GUR 4120 which was y irradiated at RT and compared to the untreated material. T2 - Jahrestagung Kerntechnik 2011 CY - Berlin, Germany DA - 17.05.2011 PY - 2011 SP - 1 EP - 5 AN - OPUS4-24620 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nöther, N. A1 - Krebber, Katerina A1 - Schneider-Glötzl, J. T1 - An all-digital implementation of the Brillouin optical frequency domain analysis for long-range distributed strain and temperature monitoring N2 - For long-range measurements in geotechnical and industrial applications, distributed optical fiber sensors have become a tool of increasing importance throughout the past decade. Classic deformation monitoring (performed by strain gauges etc.) and temperature monitoring (Pt100 and alike) deliver data from fixed, single spots of a structure; quasidistributed measurements (fiber bragg gratings) provide a Chain of discrete measurement points along a limited sensing length. In contrast, an opticai fiber connected to a device for distributed strain and temperature sensing (DTSS) will provide a continuous profile of strain and temperature - spatially resolved down to less than 1 m - over a ränge of several tens of kilometers. In DTSS measurements, the nonlinear opticai effect of stimulated Brillouin Scattering (SBS) is employed: two light waves with a stable, tunable frequency offset are injected into opposite ends of the sensing fiber, where they will form a beat pattem, at which parts of the light will be scattered. By matching the frequency offset of the light waves to the propagation of acoustic fluctuation in the opticai fiber, a power transfer from one light wave to the other can be measured; since the acoustic propagation directly shifts with train and temperature of the fiber, these two quantities can be measured by tuning the light waves’ frequency offset. T2 - 8th International symposium on field measurements in geomechanics - FMGM 2011 CY - Berlin, Germany DA - 12.09.2011 PY - 2011 SP - 1 EP - 6 AN - OPUS4-24664 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, Wolfgang A1 - Kusche, Nadine A1 - Münzenberger, Sven A1 - Schukar, Vivien T1 - KALFOS - a validation facility for strain transfer characterization of surface-applied strain sensors N2 - Strain sensors embedded in or attached to structural components have to measure the real deformation of the structure over the whole period of use. The user must know how reliably installed sensors provide strain measurement results. For this purpose, test facilities or coupon tests are used. In order to characterize the strain transfer quality from the host structure into surface-applied strain sensors, a unique testing facility has been developed. This facility can be used both for fiber optic and resistance strain sensors. Originally developed for fiber Bragg grating based sensors, the KALFOS facility (=calibration of fiber optic sensors) uses Digital Image Correlation (DIC) and Electronic Speckle Pattern Interferometer (ESPI) as unbiased referencing methods. It is possible to determine experimentally the strain transfer mechanism under combined thermal and mechanical loading conditions. This experimental characterization method will reveal weaknesses in commonly used strain sensors, and the investigation of the material systems used for fiber optic and other strain sensors (particularly the coating/substrate - adhesive combination). The KALFOS facility allows matching of specific measurement requirements with environmental conditions. T2 - SAE 2011 AeroTech Congress & Exhibition CY - Toulouse, France DA - 18.10.2011 KW - Fiber optic sensors KW - Structural health monitoring KW - Validation KW - Strain sensor KW - Surface application PY - 2011 DO - https://doi.org/10.4271/2011-01-2606 IS - Paper 2011-01-2606 SP - 1 EP - 7 AN - OPUS4-24643 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klinger, Christian A1 - Bettge, Dirk A1 - Häcker, Ralf A1 - Heckel, Thomas A1 - Gohlke, Dirk A1 - Klingbeil, Dietmar T1 - Schadensanalyse zum Radsatzwellenbruch ICE3 N2 - Am 9. Juli 2008 entgleiste ein Hochgeschwindigkeits-Triebzug der Baureihe 403, ICE3, bei der Ausfahrt aus dem Kölner Hauptbahnhof. Ursache dafür war der Schwingbruch einer Radsatzwelle. Im Auftrag der Staatsanwaltschaft Köln untersuchte die BAM die Schadensteile, insbesondere die gebrochene Treibradsatz-Hohlwelle. Zunächst wurden das Drehgestell, der Antriebsstrang, die Räder, die Bremsen und die gebrochene Radsatzwelle visuell untersucht und deren Zustand dokumentiert. Anschließend erfolgte die zerstörungsfreie Prüfung der beiden Bruchstücke der Hohlwelle mit teilmechanisierter Ultraschall-Handprüfung. Vor der Zerlegung der Radsatzwelle wurden ausgewählte Maße kontrolliert und die Oberfläche eingehend untersucht. Nach der Probenahme und Präparation wurden die relevanten spezifizierten Eigenschaften des Wellenwerkstoffs überprüft. Mittels Bruchflächenanalyse konnte die Startstelle des Schwingrisses lokalisiert, aufgrund der starken Sekundärschäden auf der Bruchfläche und an den Bruchkanten jedoch nicht direkt ausgewertet werden. Durch die Kombination von Mikro-Computertomographie und Ultraschall-Tauchtechnik wurden u. a. nahe der Schwingriss-Startstelle Inhomogenitäten erkannt, die durch metallographische Zielpräparation als nichtmetallische Einschlüsse identifiziert wurden. Die Größe dieser Einschlüsse ist gemäß gefordertem Reinheitsgrad unzulässig. Vergleichbare Einschlüsse in diesem hochbeanspruchten Bereich der Radsatzwelle haben vermutlich den Schwingriss initiiert. T2 - 43. Tagung des DVM-Arbeitskreises Bruchvorgänge - Bruchmechanische Werkstoff- und Bauteilbewertung: Beanspruchungsanalyse, Prüfmethoden und Anwendungen CY - Rostock, Germany DA - 22.02.2011 KW - Radsatzwellenbruch KW - Nichtmetallische Einschlüsse KW - Reinheitsgrad KW - Ultraschall-Hohlwellenprüfung KW - Railway axle KW - Fatigue crack KW - Root cause KW - Cologne accident PY - 2011 SP - 1 EP - 6 AN - OPUS4-25275 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krebber, Katerina ED - Ramos, G. A. T1 - Structural health monitoring by smart technical textiles based on fiber optic sensors N2 - Technical textiles with embedded distributed fiber optic sensors have been developed for the purposes of structural health monitoring in geotechnical and civil engineering. The distributed fiber optic sensors are based on Brillouin Scattering in silica optical fibers and OTDR in polymer optical fibers. Such “smart” technical textiles can be used for reinforcement of geotechnical and masonry structures and the embedded fiber optic sensors can provide information about the condition of the structures and detect the presence of any damages and destructions in real time. Thus, structural health monitoring of critical geotechnical and civil infrastructures can be realized. The paper highlights the results achieved in this innovative field in the framework of several German and European projects. T2 - SHMII-5 - 5th International conference on structural health monitoring of intelligent infrastructure CY - Cancún, Mexico DA - 11.12.2011 PY - 2011 IS - Keynote Lecture SP - 1 EP - 10 PB - National Autonomous University of Mexico CY - Mexico City AN - OPUS4-25261 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, Wolfgang A1 - Schukar, Vivien ED - Ramos, G. A. T1 - Validation of strain sensors to achieve reliable measurement results N2 - Fiber optic strain sensors are increasingly used and sensor Systems are provided with specifications. Even if the performance is well specified, the strain characteristics of the sensor, strain transfer factor, mechanical stability under thermal influences, the performance of applied strain sensors can seriously differ from virgin sensor’s the performance. Therefore the contribution considers validation issues to come to reliable strain measurements and how to validate strain measurements of applied sensors. A new validation facility will be presented. T2 - SHMII-5 - 5th International conference on structural health monitoring of intelligent infrastructure CY - Cancún, Mexico DA - 11.12.2011 PY - 2011 IS - Session 20, Topic 2.3 SP - 1 EP - 13 PB - National Autonomous University of Mexico CY - Mexico City AN - OPUS4-25309 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, M. A1 - Vaterrodt, K. A1 - Heidmann, G. A1 - Habel, Wolfgang A1 - Vogelsang, R. A1 - Weissenberg, W. A1 - Sekula, O. A1 - Pepper, D. A1 - Emanuel, H. A1 - Plath, R. T1 - Optical PD detection in stress cones of HV cable accessories N2 - Sensitive partial discharge (PD) measurements on HV/EHV cable systems are usually based on electrical or electromagnetic PD detection. Unfortunately, interferences may significantly reduce sensitivity, especially in on-site after-installation testing and, even more, in on-line PD monitoring. This paper deals with optical PD detection, which is absolutely immune to any kind of electromagnetic interference. Optical PD detection necessarily requires transparent or translucent insulation systems to be applicable. Stress cone elements for HV/EHV cable accessories meet the requirements for optical PD detection, if made from transparent silicone elastomers. T2 - 8th International Conference on Insulated Power Cables CY - Versailles, France DA - 19.06.2011 PY - 2011 IS - B.8.4 SP - 1 EP - 5 PB - Jicable CY - Paris AN - OPUS4-25310 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habel, Wolfgang A1 - Röben, R. A1 - Hüttl, R. A1 - Kuchejda, M. ED - Ramos, G. A. T1 - Monitoring of corrosion protection in reinforced concrete structures using an integrated pH optode N2 - Corrosion in steel-reinforced concrete structures is a critical issue. Corrosion appears if the pH value of the concrete matrix decreases due to deterioration of the Calcium hydroxide layer on the Steel surface. The safest Information about potential danger of Steel corrosion is the knowledge of the pH value of concrete. The paper presents a Tiber optic pH sensor for long-term monitoring of the pH value of reinforced concrete structures at risk from corrosion. The sensor probe is small (about 8 mm in diameter), can be embedded into the concrete matrix and observe changes in pH over years. Several sensor probes can be staggered to detect the progression of pH decrease. The pH values can be resolved with 0.1 to 0.2 pH value in the ränge between 12.0 and 9.5. The structure of the pH measurement System, longterm test results and the design to achieve stable probes will be explained. Experienee from test applications of pH sensors embedded in grouted anchors and in concrete components for a cooling tower will be presented. T2 - SHMII-5 - 5th International conference on structural health monitoring of intelligent infrastructure CY - Cancún, Mexico DA - 11.12.2011 PY - 2011 IS - Session 15, Topic 4.5 SP - 2 EP - 8 PB - National Autonomous University of Mexico CY - Mexico City AN - OPUS4-25311 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Döhler, M. A1 - Hille, Falk A1 - Lam, X.-B. A1 - Mevel, L. A1 - Rücker, Werner ED - Proulx, T. T1 - Confidence intervals of modal parameters during progressive damage test N2 - In Operational Modal Analysis, the modal parameters (natural frequencies, damping ratios and mode shapes) obtained from Stochastic Subspace Identification (SSI) of a structure, are afflicted with statistical uncertainty. For evaluating the quality of the obtained results it is essential to know the respective confidence intervals of these figures. In this paper we present algorithms that automatically compute the confidence intervals of modal parameters obtained from covarianceand data-driven SSI of a structure based on vibration measurements. They are applied to the monitoring of the modal parameters of a prestressed concrete highway bridge during a progressive damage test that was accomplished within the European research project IRIS. Results of the covariance- and data-driven SSI are compared. T2 - 29th IMAC - Conference on structural dynamics CY - Jacksonville, FL, USA DA - 31.01.2011 KW - Stochastische subspace basierte Identifikation KW - Schadensdetektion KW - Spannbetonbrücke PY - 2011 SN - 978-1-4419-9304-5 DO - https://doi.org/10.1007/978-1-4419-9305-2_17 SN - 2191-5644 N1 - Serientitel: Conference Proceedings of the Society for Experimental Mechanics Series – Series title: Conference Proceedings of the Society for Experimental Mechanics Series VL - 4 SP - 237 EP - 250 PB - Springer AN - OPUS4-24335 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mix, Renate A1 - Friedrich, Jörg Florian T1 - Improvement of adhesivity of polypropylene by its surface modification using the aerosol dielectric barrier discharge N2 - Plasma processes are used in many fields of Science and technology. While a plasma oxygen treatment produces a broad variety of different oxygen-containing functional groups, tailored - surface functionalisation demands preset functional groups in known concentration. Due to the fact that most of plasma experiments need expensive vacuum equipment increased efforts are to observe to apply atmospheric pressure plasma processes. Thus, Dielectric Barrier Discharge (DBD) and corona treatment of polymer foils have a long tradilion in industry to modify them for printing, laminating, adhesion promotion, etc. Thercibre, increasing interest is observed to make these atmospheric pressure processes more effeclive. Newly developed methods like plasma-printing were used for surfaces in biological and medical applications or for printed circuits. T2 - ADHESION `11 - 11th Triennial conference on the science and technology of adhesion and adhesives CY - York, UK DA - 07.09.2011 PY - 2011 SP - 253 EP - 256 AN - OPUS4-24337 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eisenacher, Germar A1 - Scheidemann, Robert A1 - Neumann, Martin A1 - Wille, Frank A1 - Droste, Bernhard T1 - Approach for a finite element material model for wood for application in mechanical safety cases of transport packages N2 - BAM Federal Institute for Materials Research and Testing is the competent authority for mechanical safety assessment of transport packages for radioactive material in Germany. The further development of state-of-the-art technology concerning assessment methods is essential for a qualified work of involved designers and authority experts. The paper gives an example of current development done to improve understanding and modeling capabilities of wood filled impact limiter. In order to reduce the loads applied to the package containment, which result from regulatory drop tests, most packages are protected by energy dissipating impact limiter. Wood, encapsulated by steel sheets, is one of the materials typically used for energy dissipation in these impact limiter. Very often, mechanical safety cases regarding the 9 m drop test are performed computationally, where it is essential to use reliable and verified computational methods and models. In this context, the paper presents an approach for a finite element material model for wood. Thereby, the mechanical behavior of wood under compression loading is the focus of the development work. Additionally, material orientation as well as strain rate, temperature and lateral constraint may vary. A large number of experiments, particularly compression tests, was designed and performed to establish an adequate experimental database for modeling verification. The experimental results enabled the derivation of necessary requirements: The material model has to take into account strain rate and temperature dependencies as well as the anisotropic characteristics of the material, a proper yield criterion, flow rule and hardening law. Such a material model is currently not available in established commercial dynamic finite element codes. Thus it is necessary to create a user-defined material model considering the mentioned requirements. A first step was done by determining a yield surface as well as detecting flow and hardening mechanisms from experimental force-deflection curves. In a next step the LS-DYNA material model MAT_75 was altered according to conclusions of former BAM development work, regarding the modeling of post-peak softening as a function of lateral constraint. Future research will contain the further development, implementation and verification of a material model for wood. T2 - 52nd INMM Annual meeting CY - Palm Desert, CA, USA DA - 17.07.2011 KW - Impact limiter KW - Material model wood KW - Transport package PY - 2011 SP - 1 EP - 8 AN - OPUS4-24236 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Robertson, Daniela A1 - Böhning, Martin A1 - Schröder, Hartmut A1 - Brummermann, K. A1 - Kaudinya, I. A1 - Saathoff, F. T1 - Möglichkeiten der Abschätzung der Langzeitbeständigkeit von Kunststoffdichtungsbahnen (KDB) auf Polyolefinbasis für den Tunnelbau N2 - Im Rahmen eines von der Bundesanstalt für Straßenwesen (BASt) initiierten Forschungsvorhabens (15.449/2007/ERB: „Prüfverfahren zur Beurteilung der Lebensdauer von Kunststoffdichtungsbahnen für Straßentunnel“) wurden anhand von Untersuchungen an Kunststoffdichtungsbahnen (KDB) auf Basis von Polyolefinwerkstoffen die Möglichkeiten der Beurteilung der oxidativen Langzeitbeständigkeit sondiert. Im Mittelpunkt stand die Erprobung des Autoklaventests in Anlehnung an DIN EN ISO 13438 (Methode C1/C2) an ausgewählten, für den Tunnelbau repräsentativen marktüblichen KDB-Produkten. Die Untersuchungen im Autoklaven bei erhöhten Temperaturen (60 °C, 70 °C und 80 °C) und Sauerstoffdrücken (11, 21 und 51 bar) wurden durch vergleichende Versuche im Wärmeschrank (Ofen) bei erhöhter Temperatur (85 °C) in Anlehnung an DIN EN 14575 ergänzt. Die KDBProdukte wurden außerdem einer eingehenden Materialcharakterisierung (Zugprüfung, DMA, DSC) unterzogen. Weiterhin wurden Bauwerksdaten recherchiert und auf ihre Nutzbarkeit zur Bewertung und Prüfbarkeit der Langzeitbeständigkeit von KDB in Tunneln betrachtet. Ziel war auch, die Anwendbarkeit des bisher vorgeschlagenen Extrapolationsmodells zur Auswertung der Ergebnisse von Autoklaventests an im Tunnelbau marktüblichen Produkten für Nutzungsdauern über 25 Jahre zu überprüfen und zur Entwicklung eines geeigneten Prüfverfahrens beizutragen. Der Beitrag geht auf Ergebnisse des Vorhabens ein und zeigt erste Schlussfolgerungen und weiteren Untersuchungsbedarf auf. Die Ergebnisse werden in den „Empfehlungen zu Dichtungssystemen im Tunnelbau EAG-EDT“ des Arbeitskreises 5.1 „Kunststoffe in der Geotechnik und im Wasserbau“ berücksichtigt, deren 2. Auflage in Vorbereitung ist. Aspekte des thermischen Verhaltens der eingesetzten Werkstoffe sowie mögliche Anpassungen der Prüfrandbedingungen für die Autoklaventests werden ergänzt und Hinweise zur Interpretation von Prüfergebnissen gegeben. Außerdem wurden inzwischen ausgehend von den Ergebnissen des Forschungsvorhabens erste Autoklaven-Ringversuche in drei Prüfinstitutionen initiiert. T2 - 12. Informations- und Vortragstagung über "Kunststoffe in der Geotechnik" CY - Munich, Germany DA - 03.03.2011 KW - Kunststoffdichtungsbahnen auf Polyolefinbasis KW - Oxidative Langzeitbeständigkeit KW - Autoklaventest - beschleunigte Alterung KW - DSC KW - DMA PY - 2011 SN - 978-3-940476-26-5 IS - Geotechnik Sonderheft 2011 SP - 35 EP - 42 AN - OPUS4-24399 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Köppe, Enrico A1 - Bartholmai, Matthias ED - Tsamis, C. ED - Kaltsas, G. T1 - Wireless sensor network with temperature compensated measuring technology for long-term structural health monitoring of buildings and infrastructures N2 - Damage to buildings occurs if a construction component fails. The result is a partial or total collapse which can be dangerous for people for example if it's a bridge or a large hall. The collapse of the terminal building at the Airport Charles de Gaulle in Paris and the damage at the historic City Archives of Cologne are typical examples of such accidents. Another problem is the contradiction of the increasing volume of traffic (particularly heavy traffic) and the great age of bridges. The probability increases that the load-bearing capacity of a bridge decreases. For example the collapses of the Mississippi Bridge and of the Inntal Motorway Bridge can be seen as results. Therefore it is necessary to control endangered structures during their life span. In order to prevent these kinds of accidents, the Federal Institute for Materials Research and Testing developed a radio-based, self-configuring measuring system in cooperation with the ScatterWeb Company, Berlin (Germany). This measuring system consists of identically designed sensor modules which are self-sustaining, wireless, act as transmitters and receivers and are equipped with a special sensor technology for long-term monitoring of buildings or engineering facilities. The sensor unit uses strain gauges for stress analysis and contains interfaces for additional sensors. The system in particular applies to buildings and structures for transport and traffic and large-scale industrial facilities, where a subsequent wiring installation is difficult or impossible. T2 - Eurosensors XXV CY - Athens, Greece DA - 04.09.2011 KW - Multi-Hop WSN KW - SHM KW - Temperature and Frequency Compensation KW - Funksensorik KW - Sensornetzwerk KW - Multihop KW - Strukturüberwachung KW - Temperaturkompensation PY - 2011 UR - http://www.sciencedirect.com/science/article/pii/S1877705811059236 IS - Paper 1197 SP - 1 EP - 5 PB - Elsevier AN - OPUS4-24401 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Köppe, Enrico A1 - Bartholmai, Matthias A1 - Liers, A. A1 - Schiller, J. T1 - Tracking persons using a radio-based multi-sensor system N2 - A multi-sensor system for 3D localization was developed and named BodyGuard. It combines body movement sensing and a guard system for the tracking and recording of the status of persons. BodyGuard was designed to monitor and transmit the movement of a person radio-based and to transform that data into a spatial coordinate. This paper describes how the BodyGuard system works, what components the system consists of, how the individual sensor data is converted into 3D motion data, with which algorithms the individual sensors are processed, how individual errors are compensated and how the sensor data are fused into a 3D Model. T2 - IPIN 2011 - International conference on indoor positioning and indoor navigation CY - Guimaraes, Portugal DA - 21.09.2011 KW - Wireless sensor network (WSN) KW - Embedded systems KW - Sensor calibration and validation KW - Person tracking KW - Inertial navigation system KW - Inertial measurement unit PY - 2011 SP - 1 EP - 4 AN - OPUS4-24402 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Musolff, André A1 - Komann, Steffen A1 - Droste, Bernhard A1 - Müller, Karsten A1 - Quercetti, Thomas T1 - Drop test program with a HLW cask model - performance, measurements and results N2 - BAM (Federal Institute for Material Research and Testing) is the competent authority for mechanical and thermal safety assessment of transport packages for spent fuel and high level waste (HLW) in Germany. In context with package design approval of the new German HLW cask CASTOR HAW28M, BAM performed several drop tests with a half-scale model of the CASTOR HAW/TB2. The test model was manufactured by GNS (Gesellschaft fur Nuklear Service mbH) and tested under accident transport conditions on the 200 tons BAM drop test facility at the BAM Test Site Technical Safety. For this comprehensive test program the test specimen CASTOR HAW/TB2 was instrumented at 21 measurement planes with altogether 23 piezo-resistive accelerometers, five temperature sensors and 131 tri-axial strain gauges in the container interior and exterior, respectively. The strains of four representative lid bolts were recorded by four uniaxial strain gauges per each bolt. Helium leakage rate measurements were performed before and after each test in the above noted testing sequence. The paper presents some experimental results of the half-scale CASTOR HAW/TB2 prototype (14,500 kg) and measurement data logging. T2 - 52nd INMM Annual meeting CY - Palm Desert, CA, USA DA - 17.07.2011 KW - Drop test results KW - Spent fuel transport cask KW - Impact limiter KW - Measurement methods KW - Drop test program PY - 2011 SP - 1 EP - 9 AN - OPUS4-24245 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heinze, Christoph A1 - Schwenk, Christopher A1 - Rethmeier, Michael ED - Zoch, H.-W. ED - Lübben, T. T1 - Influences on the result quality of numerical calculation of welding-induced distortion N2 - The present investigations cover different relevant influences on the numerical calculation of welding-induced distortion. Therefore, a single-layer pulsed gas metal arc (GMA) weld of structural Steel S355J2+N with a thickness Öf5 mm is experimentally and numerically investigated. The influences of mesh density, tack-welds, and continuous cooling transformation (CCT) diagrams on welding-induced distortion are studied. The quality and quantity of These effects are clarified based on the used experimental and numerical set up. The occurring differences between the investigated cases achieve significant values. Consequently, prediction of welding-induced distortion can be improved considering the present investigations. T2 - IDE 2011 - 3rd International conference on distortion engineering 2011 CY - Bremen, Germany DA - 14.09.2011 KW - Welding simulation KW - Welding-induced distortion KW - Mesh analysis KW - Tack welding KW - Continuous cooling transformation behaviour PY - 2011 SN - 978-3-88722-724-1 SP - 277 EP - 285 AN - OPUS4-24363 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Liehr, Sascha A1 - Krebber, Katerina T1 - A dynamic fiber optic strain and power change sensor N2 - A dynamic and quasi-distributed sensor principle for simultaneous measurement of length changes and optical power changes between reflection points in an optical fiber is presented. The technique is based on the incoherent optical frequency domain reflectometry (I-OFDR). Length change resolutions < 1 µm and measurement repetition rates up to 2 kHz can be achieved using standard single-mode and multi-mode optical fibers. Simultaneous length change and refractive index measurement as well as field test results showing the deformation of a masonry building under seismic load are presented. Promising fields of application for this technique are the structural health monitoring sector and chemical process control. T2 - 21st International conference on optical fibre sensors CY - Ottawa, Canada DA - 15.05.2011 KW - Distributed sensor KW - Strain sensor KW - Optical fiber sensor KW - Structural health monitoring KW - OFDR KW - Dynamic sensor PY - 2011 SN - 978-0-8194-8246-4 DO - https://doi.org/10.1117/12.884577 VL - 7753 SP - 775351-1 EP - 775351-4 AN - OPUS4-24266 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mishra, Kirti Bhushan A1 - Wehrstedt, Klaus-Dieter T1 - Burner for peroxy-fuels (PEROXY-BAM Burner) N2 - A new burner concept (PEROXY-BAM®) for the combustion of liquid organic peroxides (Peroxy-fuels) is presented. As peroxy-fuels are thermally unstable the design of burners for them should be accordingly modified ensuring a safe operation. It is found that 10 to 100 time less amounts of peroxy fuels are required for the same heat flux or output in comparison to hydrocarbons. Correspondingly, the fuel pump power and the volume of combustion chamber (furnace) are also reduced. As a result of less amount of fuel the emissions will also be stepped down and oxygen in the molecule helps to establish conditons like in an oxy-fuel combustion process. The advantages of using peroxy-fuels over hydrocarbons inside a model combustion chamber are also investigated with the help of CFD (Computational Fluid Dynamics) simulations. T2 - 25. Deutscher Flammentag - Verbrennung und Feuerung CY - Karlsruhe, Germany DA - 14.09.2011 KW - Organic peroxide KW - Peroxy-fuel KW - Burner concept KW - Combustion KW - Combustion chamber PY - 2011 SN - 978-3-18-092119-8 SN - 0083-5560 N1 - Serientitel: VDI-Berichte – Series title: VDI-Berichte VL - 2119 SP - 307 EP - 312 PB - VDI-Verl. AN - OPUS4-24388 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Kömmling, Anja A1 - Wachtendorf, Volker ED - Reichert, T. T1 - UV-LEDs - a new tool to determine the spectral response N2 - To determine a polymer’s spectral response of photo degradation, two main methods have been established. The so-called “filter technique” uses polychromatic radiation, which is filtered by a set of various sharp cut-on filters. This procedure provides separated reading points of an activation spectrum of the investigated material. With the "spectrographic technique” a specimen is irradiated with pectrally dispersed radiation, locally quasi monochromatically, and the local property changes.are related to the radiant exposure at the respective wavelengths. A third method, the irradiation of specimens with quasi monochromatic radiation behind interference filters, is rarely used. These methods have advantages and disadvantages and therefore, there are limits for conclusions from these spectral data. Concerning the quasi monochromatic Irradiation of specimens the development of new UV radiation sources looks promising. With the rapid development of inexpensive UV Light-emitting diodes (LEDs), new : sources of nearly monochromatic radiation in the UV ränge are available, even down to about 250 nm. To determine the spectral response, the use of such UV-LEDs in TO-18 ) and TO-39 metal cases combines the advantages of low cost and energy efficiency, stable spectral irradiance, temperature.and humidity control, larger specimen areas, and an easy and stable analysis. Combinations of different UV LEDs are also discussed as replacement for xenon arc ' radiation sources, see patent application EP01528388A1. T2 - 5th European weathering symposium - Natural and artificial ageing of polymers CY - Lisbon, Portugal DA - 21.09.2011 KW - UV resistance KW - Weathering KW - Spectral sensitivity KW - Action spectrum KW - UV-LEDs PY - 2011 SN - 978-3-9813136-2-8 N1 - Serientitel: CEEES Publication – Series title: CEEES Publication IS - 15 SP - 77 EP - 86 PB - GUS (Gesellschaft für Umweltsimulation) CY - Pfinztal AN - OPUS4-24396 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Shcheglov, Pavel A1 - Gumenyuk, Andrey A1 - Gornushkin, Igor B. A1 - Rethmeier, Michael T1 - Experimental investigation of the laser-plume interaction during high power fiber laser welding N2 - The effect of the well-known plasma absorption and refraction in CO2-laser metal welding plumes is in case of high power solid state laser welding negligibly small. By contrast, the diffraction effects of shorter wavelength laser radiation are considerable. According to the results of preliminary studies, the fine condensed metal particles in the welding plume can lead to essential worsening of the laser beam quality. This work is devoted to the investigation of the lasermatter interaction during up to 20 kW ytterbium fiber laser welding of thick mild steel plates. The plume attenuation of a probe 1.3 µm wavelength diode laser beam as well as of continuous radiation in 250-600 nm wavelength range was measured during welding with and without Ar shielding gas supply. The measured results allow it to calculate average size and concentration of fine condensed metal particles in different plume areas using the multi-wavelength method and the Mie scattering theory. The plume temperature, which determines the condensation conditions, was measured by means of Fe I atom spectral line emission registration. The obtained results can be also of interest for remote metal treatment with high-power fiber or disc lasers. T2 - 30th ICALEO - International congress on applications of lasers & electro-optics CY - Orlando, FL, USA DA - 2011-10-23 PY - 2011 SN - 978-0-912035-94-9 SP - Paper 1606, 637 EP - 645 AN - OPUS4-24921 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Miccoli, Lorenzo A1 - Perrone, C. A1 - Müller, Urs A1 - Gardei, André A1 - Ziegert, C. ED - Drochytka, R. ED - Bohus, S. T1 - Structural performances of earthen building materials. A comparison between different typologies N2 - Traditional construction techniques utilizing earthen materials are often seen as inferior compared to modern ways of building. Structural earthen elements are perceived as vulnerable towards environmental influences (moisture, frost) and in particular towards the load scenarios during earthquakes. In comparison to the recent advances in research on stone and brick masonry, knowledge on the structural performance of earthen building construction is limited and scattered. Consequently the confidence in the performance of these earthen buildings constructed in the traditional techniques during earthquakes is fairly low. The research presented here aims to make a comparison of mechanical behavior between different earth masonry material typologies, consisting of earth block masonry, rammed earth and cob. The paper has been developed in the framework of a larger research program called NIKER. BAM and other seventeen research partners from the Mediterrean area are jointly involved to develop and validate innovative materials and technologies for the systemic improvement of the seismic behavior of Cultural Heritage assets T2 - 2nd WTA - Internaitonal PhD Symposium - Building materials and buidling technology to preserve the built heritage CY - Brno, Czech Republic DA - 06.10.2011 KW - Earth masonry KW - Material test KW - Mechanical behavior KW - Cultural heritage PY - 2011 SN - 978-3-937066-21-9 SN - 0947-6830 N1 - Serientitel: WTA-Schriftenreihe – Series title: WTA-Schriftenreihe VL - 2 / Part 2 IS - 36 SP - 86 EP - 94 PB - WTA Publications AN - OPUS4-24928 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stark, Wolfgang A1 - Teteris, Gundars A1 - Braun, Ulrike A1 - Bohmeyer, W. A1 - Lange, K. T1 - Kontrolle der Vernetzungsreaktion bei reaktiven Harzen - DSC, Rheologie, DMA, FTIR und Online-Ultraschall im Vergleich N2 - Faserverbundbauteile werden durch Tränkung von Fasergewebe mit flüssigem Harz, in der Regel Epoxidharzen, und anschließender Härtung des Harzes gefertigt. Dabei kann man das Gewebe im Vorfeld mit reaktivem Harz tränken und als so genanntes Prepreg verarbeiten oder man injiziert das frisch mit dem Härter gemischte Harz in ein Werkzeug, in dem das Gewebe bereits liegt - z. B. beim RTM-Prozess. Ausgehend von der Aufgabenstellung, eine Prepregherstellung mit hohem Qualitätsstandard zu realisieren und Möglichkeiten der Fertigungskontrolle für den Prepreg-Verarbeiter aufzuzeigen, wurde an einem für die Prepregherstellung vorgesehenen Harzsystem eine weitgehende Charakterisierung des Aushärtungsverlaufs vorgenommen. Wegen der Schwierigkeit, schnell konstante Aushärtungstemperaturen zu erreichen, wurden bei allen Methoden mit einer Heizrate von 1 K/min von RT bis 200 °C aufgeheizt. T2 - Technomer 2011 - 22. Fachtagung über Verarbeitung und Anwendung von Polymeren CY - Chemnitz, Deutschland DA - 10.11.2011 KW - Thermoanalyse KW - Lineare Aufheizung KW - Online Prozesskontrolle KW - Epoxidharz KW - Prepreg PY - 2011 SN - 978-3-939382-10-2 IS - Kap. 1.1 SP - 1 EP - 9 AN - OPUS4-24910 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Molnarne, Maria A1 - Wilrich, Cordula A1 - Holtappels, Kai T1 - Chemically unstable gases and gas mixtures - new categories in the GHS N2 - In connection with the use of chemically unstable gases (especially acetylene and ethylene oxide) accidents keep on happening - amongst them also quite serious ones. These gases are known to be chemically unstable. A chemically unstable sas is a flammable gas that is able to react exolosivelv even in the absence of air or oxveen. The investigation of accidents showed that the Chemical instability of flammable gases played an important role in the severity of accidents. Therefore, this hazardous property was included in the global harmonizatiön of the Classification of Chemicals. The Classification of chemically unstable flammable gases and mixtures is an amendment to Chapter 2.2 “Flammable gases” of the UN Globally Harmonized System of Classification and Labelling of Chemicals (GHS), because most chemically unstable gases are flammable as well. The proposal to add them to the GHS originated from the experts of an informal working group of the UN Sub-Committee of Expert on the GHS (UNSCEGHS) headed by BAM, Germany. The UNSCEGHS has decided to include it in the Fourth Revised Edition of the GHS. The respective method for determining whether a gas is chemically unstable or not, is included in the UN Manual of Tests and Criteria. This paper presents some experimental investigations of these gases, the test methods, examples of new classifications and results from CHEMSAFE T2 - 14th Annual symposium, Mary Kay O´Connor process safety center - Beyond regulatory compliance: making safety second nature CY - College Station, TX, USA DA - 25.10.2011 KW - Chemically unstable gases KW - GHS KW - Chemisch instabile Gase PY - 2011 SP - 871 EP - 882 AN - OPUS4-24913 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Urs A1 - Schlegel, Moritz-Caspar A1 - Emmerling, Franziska T1 - Advanced techniques for studying damage mechanisms of cementitious matrices affected by sulfate attack N2 - Cementitious materials, in particular concrete, are durable materials if prepared appropriately and the Service life of concrete structures is now often required to last 120 years or more. Concrete durability depends strongly on intrinsic (e.g. composition, porosity) and exterior factors (e.g. moisture condition and composition, frost cycles, load pattem). Deleterious actions leading to concrete degradation are often created by the environment. Extemal sulfate attack is one of the more spectacular damage scenarios for concrete structures caused by the ingress of sulfate ions into the pore System of the material and successive formation of expanding phases. Though in recent years well studied there are still many questions remaining conceming the mechanisms of sulfate attack. In particular over the last ten years, with the increased utilization of blended cements, new questions arose concerning the sulfate resistance of those binder Systems. In the presented study therefore a method was developed to analyze the changes of the phase composition within the micro structure due to sulfate attack. The analytical method was based on pX-Ray diffraction (pXRD) using Synchrotron radiation in Debye-Scherrer (transmission) geometry. The spatial resolution of the method is ca. 10 pm and allows the characterization of phase transformations in the wake of damaging processes in more detail compared to other techniques. Furthermore, the experimental setup provides the possibility for analyzing the phase assemblage of a given sample without destroying the micro structure. This is possible because the specimens for phase analysis consists of thick sections, which can be used for further microscopic analysis of the micro structure and micro chemistry (e.g. by SEM-EDX). Samples containing supplementary cementitious materials were measured in comparison and to reconstruct the influence of the degradation process in detail. Additionally, reaction ffonts within the samples were localized by micro x-ray fluorescence analysis (MXRF). T2 - EMABM 2011 - 13th Euroseminar on microscopy applied to building materials CY - Ljubljana, Slovenia DA - 14.06.2011 KW - Sulfate attack KW - Concrete KW - Synchrotron KW - XRD KW - Phase analysis PY - 2011 SN - 978-961-90366-7-9 SP - 1 EP - 9 AN - OPUS4-24878 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ortwein, Hans-Peter A1 - Trappe, Volker A1 - Bohse, Jürgen A1 - Hickmann, Stefan ED - Grellmann, W. T1 - In-Situ-Messung der Matrixschädigung in kohlenstofffaserverstärktem Kunststoff unter uni- und biaxialer Zugbelastung N2 - Die Restlebensdauerabschätzung von Faserkunststoffverbunden ist ein ungelöstes Problem. Die Beobachtung der Matrixschädigung ist dabei ein vielversprechender Ansatz zur Bewertung des Schädigungszustandes insgesamt. Unter kombinierter Beobachtung mit Röntgenrefraktionsmessungen und Schallemissionsmessung wurden uni- und biaxiale Lasten statisch und zyklisch auf Kohlenstofffaserepoxidharz-Proben aufgebracht. Die uniaxiale Belastung erfolgt mittels einer eigenentwickelten Kompaktprüfmaschine direkt während der Röntgenrefraktions- und Schallemissionsmessung in der Röntgenkammer. Die biaxiale Belastung wird an Modelldruckbehältern ebenfalls mit Schallemissionsmessung durchgeführt. Hier wird der Modelldruckbehälter mit dem Röntgenrefraktionsverfahren periodisch inspiziert. T2 - DVM-Tagung Werkstoffprüfung 2011 - Neue Entwicklungen in der Werkstoffprüfung - Herausforderungen an die Kennwertermittlung CY - Berlin, Germany DA - 01.12.2011 KW - Druckbehälterprüfung KW - CFK KW - Schallemissionsmessung KW - Röntgenrefraktionsmessung KW - Matrixschädigung KW - Faserkunststoffverbund KW - Druckbehälter PY - 2011 SN - 978-3-9814516-1-0 SN - 1861-8154 N1 - Serientitel: DVM-Bericht – Series title: DVM-Bericht IS - 643 SP - 161 EP - 166 AN - OPUS4-24931 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Häcker, Ralf A1 - Klinger, Christian A1 - Kahlcke, Ole A1 - Schriever, Sina ED - Grellmann, W. T1 - Zwischen Zeitstand und Relaxation - Einfluss der Proben- und Prüfmaschinensteifigkeit auf die Lebensdauer unter konstanter Belastung N2 - Zur Abschätzung der Lebensdauer eines bei höherer Temperatur langzeitbelasteten Bauteils wurden Zeitstandversuche, Relaxationsversuche und weitere Versuche mit unterschiedlichen Umgebungssteifigkeiten durchgeführt. Die Zeitstandversuche, deren Versuchsführung eine unendlich niedrige Umgebungssteifigkeit simuliert, liefern geringere Lebensdauern (Bruchzeiten) im Vergleich zu Versuchen mit endlich hohen, technisch relevanten Steifigkeiten bei vergleichbarer Probensteifigkeit (Geometrie), wobei die Lebensdauern mit steigender Umgebungssteifigkeit zunehmen. Die längsten Lebensdauern zeigen Relaxationsversuche mit einer unendlich hohen Umgebungssteifigkeit aufgrund ihrer Versuchsregelung. Für die Übertragung der an Proben gewonnenen Ergebnisse auf das Bauteil wurde das Steifigkeitsverhältnis Z zwischen der Steifigkeit der 'Probe' und der der 'Umgebung' definiert und angewandt. Das Steifigkeitsverhältnis des kritischen Bereichs im Bauteil und das der Werkstoffprobe in der Prüfmaschine sollten möglichst ähnlich sein. Dann lassen sich bei der Übertragung auf das Bauteil realistisch höhere Lebensdauern abschätzen als nur mit Kenntnis der Ergebnisse der Zeit-standversuche. T2 - DVM-Tagung Werkstoffprüfung 2011 - Neue Entwicklungen in der Werkstoffprüfung - Herausforderungen an die Kennwertermittlung CY - Berlin, Germany DA - 01.12.2011 KW - Zeitstandverhalten KW - Steifigkeit KW - Relaxationsversuch KW - Lebensdauer KW - Bauteilprüfung PY - 2011 SN - 978-3-9814516-1-0 SN - 1861-8154 N1 - Serientitel: DVM-Bericht – Series title: DVM-Bericht IS - 643 SP - 267 EP - 272 AN - OPUS4-24932 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rack, T. A1 - Zabler, S. A1 - Rack, C. A1 - Stiller, M. A1 - Riesemeier, Heinrich A1 - Cecilia, A. A1 - Nelson, K. T1 - Coherent synchrotron-based micro-imaging employed for studies of micro-gap formation in dental implants N2 - Biocompatible materials such as titanium are regularly applied in oral surgery. Titanium-based implants for the replacement of missing teeth demand a high mechanical precision in order to minimize micro-bacterial leakage, especially when two-piece concepts are used. Synchrotron-based hard x-ray radiography, unlike conventional laboratory radiography, allows high spatial resolution in combination with high contrast even when micro-sized features in such highly attenuating objects are visualized. Therefore, micro-gap formation at interfaces in two-piece dental implants with the sample under different mechanical loads can be studied. We show the existence of micro-gaps in implants with conical connections and study the mechanical behavior of the mating zone of conical implants during loading. The micro-gap is a potential source of implant failure, i.e., bacterial leakage, which can be a stimulus for an inflammatory process. T2 - 10th International conference on X-ray microscopy CY - Chicago, Illinois, USA DA - 15.08.2010 KW - X-ray imaging KW - Dental implants KW - Digital radiography KW - Implant-abutment interface KW - Synchrotron radiation KW - X-ray phase contrast PY - 2011 SN - 978-0-7354-0925-5 DO - https://doi.org/10.1063/1.3625398 N1 - Serientitel: AIP conference proceedings – Series title: AIP conference proceedings VL - 1365 SP - 445 EP - 448 AN - OPUS4-25347 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mishra, Kirti Bhushan A1 - Wehrstedt, Klaus-Dieter T1 - CFD simulation to predict the performance of a peroxy-fuel burner N2 - new burner concept for peroxy-fuels is proposed. The performance of the proposed peroxy-fuel burner is predicted with the help of Computational Fluid Dynamics (CFD) simulation. It is found that peroxy-fuel burner not only requires considerable less amount of fuel for the same output/power but also at the same time the overall size of the processing unit can be reduced. As peroxy-fuels contain oxygen atoms within the molecule itself a similar to oxy-fuel combustion environment is created without even supplying pure oxygen. CFD simulations also support the above facts and demonstrate the existence of less favorable conditions to form NOx. T2 - 38th National conference on fluid mechanics and fluid power CY - Bhopal, India DA - 15.12.2011 KW - Burner KW - Peroxy-fuels KW - Performance KW - CFD simulation PY - 2011 IS - Paper HT-07 SP - 1 EP - 6 AN - OPUS4-25380 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sojref, Regine A1 - Güther, Wolfgang T1 - Solvent-based redispersion of fine (<200 nm) corundum powder pre-milled in water T2 - ECerS XII - 12th Conference of the European ceramic society CY - Stockholm, Sweden DA - 2011-06-19 KW - Powder processing KW - Redispersion KW - Tape casting KW - Corundum KW - Hydrophobization PY - 2011 SP - 1 EP - 4 AN - OPUS4-25379 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helm, C. A1 - Eichler, Thorsten A1 - Raupach, M. A1 - Isecke, Bernd T1 - Time dependency of current and potential distribution during the cathodic protection of RC structures N2 - Cathodic protection (CP) is a common method for rehabilitation of reinforced concrete structures suffering from Chloride induced corrosion. A sufficient protection of the corroding rebar can be ensured by use of several protection criteria. The use of these assessment criteria, in particular the so called 100 mV-criterion, can lead to erroneous resuits for certain unconventional arrangements of rebar and cp anode. Therefore a joint research project of the Institute for Building Materials Research, RWTH-Aachen University, Germany, (ibac) and the Federal Institute for Materials Research and Testing, Berlin, Germany, (BAM) has been set up to determine the applicability of CP under arbitrary geometrical conditions. A special focus was set on the applicability of surface applied anode Systems for protection of the reinforcement of structures opposite to the accessible side (e.g. outer side of tunnel Shell, Bridge deck protected from inside a box girder) In this paper, the impact of the time dependent changes of the Polarisation behaviour of the rebar on the current and potential distribution is shown by means of parametric studies using the FEM method. T2 - EUROCORR 2011 - Developing solutions for the global challenge CY - Stockholm, Sweden DA - 04.09.2011 KW - Cathodic protection KW - Long time effects of cathodic polarisation KW - FEM-modelling KW - Steel in concrete PY - 2011 SP - 1 EP - 11 AN - OPUS4-25326 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -