TY - CONF A1 - Georg, Paul A1 - Block, R. A1 - Heister, W. A1 - Holl, S. A1 - Pulm, A. A1 - Hofmann-Böllinghaus, Anja T1 - A score regarding the need for assistance - considering pedestrians with impairments in evacuation planning N2 - The capabilities of pedestrians for evacuation have a significant impact on the time required to reach a safe place. Usually, the evacuation is split into two main stages: pre-movement-phase and movement-phase. For both a large number of studies investigate different representations of behaviour and impacts. But the influence of impairments is usually not taken into account. In addition, most of the scientific researches focus the investigation of the movement phase. This publication presents a novel approach to score the need for assistance and to estimate the effect on evacuation performance. The proposed score considers characteristic impairments in three dimensions of behaviour: reception, perception and realisation. In an unannounced evacuation training in a sheltered workshop, the evacuation behaviour and pre-movement phase were analysed. The analysis indicates that the pre-movement time depends on the kind of impairment as well as on organisational boundaries. Despite the special needs for assistance, the evacuation process in a sheltered workshop is quite similar to other sub-populations. T2 - 5. Magdeburger Brand- und Explosionsschutztage 2017 CY - Magdeburg, Germany DA - 23.03.2017 KW - Human behaviour KW - Human factors KW - Egress KW - Evacuation KW - Persons with impairments PY - 2017 SN - 978-3-00-056201-3 DO - https://doi.org/10.978.300/0562013 SP - 1 EP - 13 CY - Magdeburg AN - OPUS4-40051 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krentel, Daniel A1 - Tschirschwitz, Rico A1 - Kluge, Martin A1 - Askar, Enis A1 - Habib, Abdel Karim A1 - Kohlhoff, Harald A1 - Neumann, Patrick P. A1 - Rudolph, Michael A1 - Schoppa, André A1 - Storm, Sven-Uwe A1 - Szczepaniak, Mariusz T1 - Experimental investigation of failure of LPG gas tanks in passenger cars during full fire development N2 - In continuation of a preceding test series involving sole LPG vehicle tanks, three passenger cars equipped with identical toroidal steel LPG tanks were set on fire. The tanks were installed in the space normally reserved for the spare tyre, in the car boot. No safety device was installed on the tank, in order to force critical failure of the cylinder. Two of the cars were equipped with a tank filled with liquefied propane to a level of 20 % (5.3 kg), the third one was filled completely (25.5 kg). The partially filled tanks failed critically within a time period of more than 20 min after the initiation of the fire. The fully-filled tank did not rupture; the propane was released continuously through a small leak that appeared during the fire. Comprehensive equipment was used to procure measurement data, enabling an analysis of potential consequences and hazards to humans and infrastructure within the vehicle surroundings. The inner status of the tank (pressure, temperature of the liquid phase and the steel casing), the development of the fire (temperature inside and around the vehicle) and the pressure induced in the near-field in case of tank rupture were recorded. The results were analysed in detail and compared against the data gained in tests involving sole, but identical LPG tanks. T2 - FIVE 2018 CY - Boras, Sweden DA - 03.10.2018 KW - Behälterversagen KW - LPG KW - Alternative Antriebe KW - Fahrzeugbrand KW - Auswirkungsbetrachtung PY - 2018 SN - 978-91-88695-95-6 VL - 51 SP - 123 EP - 131 PB - RISE Safety CY - Boras AN - OPUS4-46310 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rabe, Frederik A1 - Kaudelka, Sven A1 - Hofmann-Böllinghaus, Anja A1 - Monreal, Nils A1 - Dülsen, Steffen A1 - Kempel, Florian A1 - Mühlnikel, Rüdiger A1 - Klaffke, Benjamin ED - Abildgaard, L.-L. ED - Sörensen, J.G. ED - Dederichs, A. T1 - Experimental and numerical investigation of enclosure fires - Application to room fires and intermediate scale tests N2 - One of our research topics focus on fire in residential buildings because approximately 80% of all fire fatalities in Europe occur in residential building fires. The aim is to identify critical fire scenarios and to model these fire scenarios with experimental and numerical methods. We perform a wide ränge of reaction-to-fire tests and use different Software tools to simulate fires. Another field of research is fire-safety of escape and rescue routes, because in case of fire, smoke in staircases can be a serious problem. In 2005, 8 people died in Berlin during a staircase fire which was caused by arson. A stroller had been ignited and the resulting smoke filled the staircase quickly. The wooden staircase also was involved in the fire. Several inhabitants tried to leave their flats via the staircase and were trapped. T2 - FSD 2014 - Fire Safety Day CY - Lyngby/Kopenhagen, Denmark DA - 12.06.2014 KW - Äquivalente Branddauer KW - Numerische Simulation KW - Brandszenarien PY - 2014 SP - 49 EP - 50 AN - OPUS4-30901 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krentel, Daniel A1 - Rudolph, Michael A1 - Tschirschwitz, Rico A1 - Kluge, Martin A1 - Askar, Enis A1 - Habib, Abdel Karim A1 - Kohlhoff, Harald A1 - Neumann, Patrick P. A1 - Schalau, Bernd A1 - Schoppa, André A1 - Storm, Sven-Uwe A1 - Szczepaniak, Mariusz A1 - Mair, Georg W. T1 - Infrared radiation measurement at failure of mobile gas vessels N2 - 15 identical off-the-shelf propane cylinders (m = 11 kg liquid propane) were underfired. The infrared Radiation of the Explosion, that occurred in the aftermath of the vessel failure, was recorded using four bolometers. These measurements are compared with an estimation of the Maximum intensity gained by an Analysis of the Video data, an Extended Version of the Stefan-Boltzmann law and a BLEVE model. T2 - 26th International Colloquium on the Dynamics of Explosions and Reactive Systems CY - Boston, USA DA - 30.07.2017 KW - Failure of gas vessels KW - Propane cylinder KW - Gas explosion KW - Consequences KW - Infrared radiation PY - 2017 SP - 1 EP - 6 PB - FM Global CY - Seattle, USA AN - OPUS4-41993 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böllinghaus, Thomas A1 - Mente, Tobias A1 - Dabah, Eitan ED - Kulkarni, D.V. ED - Samant, M. ED - Krishnan, S. ED - De, A. ED - Krishnan, J. ED - Patel, H. ED - Bhaduri, A.K. T1 - Trends in investigating hydrogen cracking and diffusion in steel welds N2 - The present contribution highlights recent trends in investigating hydrogen diffusion and cracking in steel welds. For such studies, supermartensitic stainless steels (SMSS) have exemplarily been selected. These materials have been used for offshore and marine constructions for about two decades now. They present a versatility of improved properties such as high strength to thickness ratio, good weldability and good corrosion resistance. However, as shown by respective failure cases, SMSS welds might become prone to hydrogen assisted cracking and the degradation phenomena are more easily to investigate due to the nearly homogeneous martensitic microstructure than in other materials. Generally, it has to be distinguished between cracking that occurs during or shortly after fabrication welding, or during subsequent operation of SMSS components. In order to achieve crack avoidance during fabrication and service, conclusive test sequences have to be applied, ranging from field tests at real components and full scale tests investigating the materials behavior under real service conditions to basic and small scale tests, such as tensile and corrosion tests, oriented more towards a materials ranking. Considerable testing of SMSS welds has been carried out and the present paper particularly summarizes spotlights on 1:1 scale component testing of welded tubulars, slow strain rate testing and basic tests oriented to elucidate the hydrogen behavior and degradation in SMSS weld microstructures. Also, permeation tests, hydrogen dependent degradation of mechanical properties and thermal desorption spectroscopy are adressed. As a specific item, first results of lately conducted investigations for tracking hydrogen movement in such weld microstructures by using high energy synchrotron radiation are elucidated. T2 - IIW International conference on global trends in joining, cutting and surfacing technology CY - Chennai, India DA - 21.07.2011 PY - 2011 SN - 978-81-8487-152-4 SP - 49 EP - 55 PB - Narosa Publ. House AN - OPUS4-26114 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hofmann-Böllinghaus, Anja A1 - Kaudelka, Sven T1 - Einfluss von Beschädigungen auf das Brandverhalten von WDVS N2 - Nach dem großen Baustellenbrand in Frankfurt 2012 hatte die Bauministerkonferenz (BMK) beschlossen, das Brandverhalten von Wärmedämmverbundsystemen [WDVS] hinsichtlich von Brandquellen vor der Fassade zu untersuchen. Die Feuerwehr Frankfurt hat eine Sammlung von Bränden, bei denen WDVS beteiligt waren, initiiert. Wertet man diese Sammlung hinsichtlich der Brandentstehung aus, fällt auf, dass von den insgesamt 57 Bränden 79 % (45 Brände) vor der Fassade begannen. 25 dieser 45 Brände wurden durch brennenden Müll oder Müllcontainer ausgelöst. Die meisten der gesammelten Brände (50) waren in den letzten fünf Jahren (2010 - 2014). Auf Grund dieser Erkenntnisse wurden an der BAM Müilcontainer (aus Plastik) hinsichtlich ihrer Entflammbarkeit und Wärmefreisetzung untersucht. Außerdem wurden im Auftrag der BMK Müllcontainer hinsichtlich ihrer Wärmefreisetzung und Brandentwicklung im Großversuch an der MFPA Leipzig untersucht. Mit Hilfe dieser Voruntersuchungen wurde eine Brandquelle identifiziert, die Zündquellen wie einen brennenden, Müllcontainer oder kleinere Ansammlungen von Sperrmüll repräsentiert: Es wurde eine 200 kg Holzkrippe gewählt, da die Holzkrippe bessere Ergebnisse hinsichtlich der Reproduzierbarkeit der Ergebnisse darstellt als z.B. ein Müllcontainer. Mit dieser Zündquelle wurden Großversuche an der MFPA Leipzig mit einem zugelassenen WDVS durchgeführt. Das WDVS zeigte unter diesen Prüfbedingungen ein nicht akzeptables Brandverhalten. Die folgenden zwei Versuche wurden mit Ertüchtigungsmaßnahmen durchgeführt, die eine signifikante Verbesserung des Brandverhaltens brachten. Zusätzlich wurde an der BAM eine Serie von Brandversuchen im Kieinmaßstab in der Single Burning Item (SBI) Prüfeinrichtung durchgeführt. Dabei wurde die auf das WDVS wirkende Wärmefreisetzungsrate variiert und der Einfluss von Grad und Größe von Beschädigungen der Putzschicht hinsichtlich des Brandverhaltens untersucht. Deutliche Unterschiede im Brandverhalten konnten sowohl quantitativ als auch qualitativ nachgewiesen werden. Neben der den Versuchsbedingungen zugrunde liegenden Wärmefreisetzungsrate konnten Art und Lage der Beschädigung in der Putzschicht als auch brandbeeinflussende Größen charakterisiert und beschrieben werden. T2 - FeuerTRUTZ Brandschutzkongress 2015 CY - Nuremberg, Germany DA - 18.02.2015 KW - Fassaden KW - Brandschutz KW - WDVS KW - Polystyrol PY - 2015 SP - Kap. 2.2, 269 EP - 279 AN - OPUS4-33341 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zeps, Robert A1 - Askar, Enis A1 - Ferrero, Fabio A1 - Kluge, Martin T1 - Zündtemperatur von Gasen/ Gasgemischen bei erhöhten Anfangsdrücken in Abhängigkeit vom Behältervolumen N2 - Zur Einschätzung der Wirksamkeit einer heißen Oberfläche als Zündquelle für ein Gas oder ein Gasgemisch werden in der Praxis Zündtemperaturen experimentell bestimmt. Die Zündtemperatur gemäß dem europäischen Standardverfahren EN 14522 wird bei Atmosphärendruck bestimmt und ist vor allem dazu geeignet die Wirksamkeit einer heißen Oberfläche als Zündquelle bei einem unerwünschten Stoffaustritt aus einer geschlossenen Anlage einzuschätzen. Eine Aussage bzgl. der der Zündfähigkeit an heißen Oberflächen innerhalb einer geschlossenen Anlage, z. B. in größeren Behältern bei bestimmten Gemischzusammensetzungen und höheren Anfangsdrücken, kann anhand der Zündtemperatur gemäß EN 14522 nicht getroffen werden. Die Bestimmung nach dem europäischen Standard erfolgt in einem offenen System, bei atmosphärischem Druck und in Luft als Oxidationsmittel. T2 - 11. Fachtagung Anlagen-, Arbeits- und Umweltsicherheit CY - Köthen, Germany DA - 07.11.2013 KW - Sicherheitstechnische Kenngrößen KW - Chemisch instabile Gase KW - Zerfallsfähige Gase KW - Explosion KW - Ethylenoxid KW - Tetrafluorethylen KW - Acetylen PY - 2013 SN - 978-3-86011-058-4 IS - F-02 SP - 1 EP - 14 AN - OPUS4-29534 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hofmann-Böllinghaus, Anja A1 - Kaudelka, Sven A1 - Ruhs, A. T1 - Challenges for fire safety in etic systems with polystyrene insulation N2 - Several fires involving external thermal insulating (ETIC) systems with polystyrene in Germany started an extensive discussion about fire safety of such systems. The Frankfurt fire service started to collect reports about real fire cases which involved ETICS with polystyrene two years ago. This collection shows that especially fires, which started in front of the buildings led to more severe fires of the facades than fires inside the buildings. In several fires the ignition sources were burning waste containers. Three of the real cases are discussed in more detail: a serious fire in Frankfurt on a building site and two fires of apartment buildings, which developed quite differently. Additionally the plastic waste containers, which started several fires are investigated regarding ignitability and heat release rates. The investigation shows that plastic waste containers are very effective as ignition source and that the usual placement directly in front of combustible facades can be a problem for fire safety. Moving these containers and unintentional contact with the facade can lead to damage of the facade coating. These damages were investigated qualitatively and quantitative on a wide collection of buildings. After classifying the damage intermediate scale tests were performed in a modified Single Burning Item (SBI) Test. The damage of the coating was varied as well as the power of the sand bed burner of the SBI apparatus. The damage significantly influenced the fire development on the specimen. In some tests the damaged rendering of the ETIC system collapsed and resulted in a sudden fire growth: after the collapse of the rendering the whole specimen was suddenly on fire. Several effects, which could be seen in the intermediate scale tests correspond to observations which were made in the real cases. As a consequence of the investigations challenges and possible measures to enhance fire safety of ETIC systems are discussed. T2 - Fire and materials 2015 - 14th International conference and exhibition CY - San Francisco, CA, USA DA - 02.02.2015 KW - ETICS KW - Large and intermediate scale tests KW - Facade fires PY - 2015 SP - 543 EP - 553 PB - Interscience Communications AN - OPUS4-32693 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vöse, Markus A1 - Fedelich, Bernard ED - Maruyama, K. ED - Abe, F. ED - Igarashi, M. ED - Kishida, K. ED - Suzuki, M. ED - Yoshimi, K. T1 - Grain boundary cavitation under time-varying normal stresses N2 - In a polycrystal, the development of creep damage, especially for low extemal loads, is related to nucleation and difiüsive growth of cavities on the grain boundaries. For low stresses, the contribution to cavity growth by dislocation creep of the suirounding material can be neglected. However, grain boundaiy diffitsion is mainly driven by the local normal stiess acting on the grain boundaiy. Under creep conditions, even under a constant extemal load, an individual grain boundaiy generally experiences a time-varying normal stress, due to stress redistributions within the polycrystalline stiuctuie. Indeed, a constrained cavitating grain boundaiy is relieved, since matter is transported to and deposited in the grain boundaiy plane, which causes the adjoining giains to drill apart. A Simulation proceduie based on the use of complex holomoiphic fiinctions for solving the diffiision problem has been used to investigate multiple cavity growth on a grain boundaiy subjected to a constant normal stress. A simplified model has been developed to describe the cavitation behaviour observed in the simulations. Finally, the analysis of cavitation simulations with time-vaiying nomial stresses, including the cases with veiy low or negative stresses, has been used to extend the simplified cavitation model to more general normal stiess time profiles. T2 - 12th International Conference on Creep and Fracture of Engineering Materials and Structures CY - Kyoto, Japan DA - 27.05.2012 KW - Creep damage KW - Grain boundary diffusion KW - Cavitation KW - Simulation KW - Evolution equations PY - 2012 SP - 1 EP - 4 AN - OPUS4-27544 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Adolphs, Jürgen A1 - Rübner, Katrin A1 - Schnell, A. A1 - Prinz, Carsten A1 - Peplinski, Burkhard A1 - Hempel, S. ED - Ludwig, H.-M. T1 - Porenstruktur hydrothermal erhärteter Granulate aus Mauerwerkbruch N2 - Die Herstellung hydrothermal erhärteter Granulate ist eine Möglichkeit zur Wiederverwertung von ziegelhaltigem Mauerwerkbruch, der derzeit aufgrund der heterogenen Zusammensetzung und hoher Feinanteile ein besonders hohes Verwertungsdefizit aufweist. Dabei ist die hydrothermale Erhärtung in einem Autoklav bei 200 °C und 1.6 MPa in gesättigter Wasserdampfatmosphäre eine Alternative mit geringerem Energieverbrauch im Vergleich zur thermischen Herstellung von Leichtgranulaten aus mineralischen Abfällen (Blähgranulate) oder Tonen und Schiefer (kommerzieller Blähton bzw. Blähschiefer), die bei Temperaturen von 1200-1300 °C im Drehrohrofen erfolgt. Die Festigkeit der Hydrothermalgranulate entwickelt sich bei diesem Prozess durch die Ausbildung von Calciumsilicathydrat-Phasen (CSH), die durch die Reaktion zwischen Quarzpartikeln und hydratisiertem Kalk entstehen. Die so erzeugten Hydrothermalgranulate haben Rohdichten zwischen 1500 kg/m3 und 2000 kg/m3. Damit und auch durch andere Eigenschaften unterscheiden sie sich von den thermisch erhärteten Blähgranulaten bzw. Blähtonen. Ursache dafür ist letztendlich eine sehr unterschiedliche Gefüge- und Porenstruktur. Im vorliegenden Beitrag wird hauptsächlich über die Ergebnisse der Mikrostrukturuntersuchungen an Hydrothermalgranulaten zusammen mit ihren technologischen Eigenschaften, wie Kornfestigkeit, Rohdichte und Wasseraufnahme, berichtet. T2 - 19. Ibausil - Internationale Baustofftagung CY - Weimar, Germany DA - 16.09.2015 KW - Leichtgranulat KW - Mauerwerkbruch KW - Hydrothermale Herstellung KW - Mikrostruktur KW - Porenstruktur PY - 2015 SN - 978-3-00-050225-5 VL - 2 SP - 2-291 EP - 2-298 AN - OPUS4-34878 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gaal, Mate A1 - Wernicke, Pascal A1 - Hufschläger, Daniel T1 - Pulse compression for air-coupled ferroelectret and thermoacoustic transducers N2 - The main advantage of air-coupled ultrasonic testing is the absence of a liquid couplant, which can damage some materials. However, most air-coupled testing scenarios have the challenge of low signals and a signal-to-noise ratio (SNR) several orders of magnitude lower than with couplant-assisted tech-niques. Since this challenge of small SNR also exists in radar technology, the pulse compression used there was adapted and applied to the physical conditions of air-coupled ultrasonic testing. This paper presents ultrasonic transmission measurements on a carbon-fibre-reinforced polymer plate using two experimental setups: 1) a thermoacoustic transmitter and an optical microphone and 2) a pair of ferroe-lectret transducers as transmitter and receiver. Thermoacoustic transmitters convert electrical energy to heat, which causes the air to expand thus producing acoustic waves. The optical microphone is based on a Fabry-Perot interferometer. Ferroelectrets are charged cellular polymers, having piezoelectric proper-ties and excellent acoustic matching to air. Both thermoacoustic transmitters and ferroelectrets are non-linear regarding the relationship between the excited sound pressure and the excitation voltage. Due to these physical boundary conditions, unipolar coding was used to modulate the excitation signals. Vari-ous codes were tested, and parameters of the excitation pulses were varied to find the optimal combina-tion for each experimental setup. The application of pulse compression to the combination of thermo-acoustic transmitter and optical microphone increased the signal-to-noise ratio by up to 16 dB and for the ferroelectret transducers by up to 23 dB. T2 - 30th International Congress on Sound and Vibration CY - Amsterdam, The Netherlands DA - 08.07.2024 KW - Pulse compression KW - Air-coupled ultrasonic transducers KW - Ferroelectret KW - Thermoacoustics PY - 2024 SN - 978-90-90-39058-1 SP - 1 EP - 7 AN - OPUS4-60725 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Reduction of ground-induced building vibrations by kinematic and inertial soil-structure interac-tion and by base isolation N2 - Many buildings on the soil have been measured and the transfer function freefield-to-building is ana-lysed. In general, an amplification at low frequencies, an amplification for the floor resonances, and a reduction for higher frequencies can be observed. Most of the measurement examples show a flexible behaviour along the height of the buildings. The prediction of building vibration consists typically of three steps. At first, the dynamic stiffness of the foundation and secondly the kinematic soil-structure interaction has to be calculated for example by the combined finite-element boundary-element meth-od. The stiffness of the foundation reduces the incoming waves (the kinematic interaction). Finally, the inertial interaction of the building with the foundation soil is calculated by the conventional finite ele-ment method where the dynamic foundation stiffness from the first step is added at the bottom of the building. The building on the compliant soil has a fundamental vertical resonance usually below 10 Hz. A parametrical variation clearly shows the influence of the elasticity of the building on this reso-nance frequency and amplitude. Moreover for column-type office buildings, the low-frequency floor resonances can further reduce this fundamental frequency. A 1-dimensional model has been estab-lished which can well approximate the behaviour of the 3-dimensional building models. It is used to demonstrate the effect of a base isolation with soft elements at the foundation. A rigid building model clearly over-estimates the isolation effect, which is smaller for a model with flexible walls, columns and floors. An even simpler model of an infinitely high building is suggested for the mitigation effect, and the resonance frequency of the rigid building should be replaced by a better performance indica-tor, which is based on the impedance ratio of the isolation and the wall and which can be also ex-pressed as a characteristic frequency. T2 - 30th International Congress on Sound and Vibration CY - Amsterdam, Netherlands DA - 08.07.2024 KW - Building vibrations KW - Base isolation KW - Foundation stiffness KW - Kinematic soil-structure interaction KW - Transfer functions of flexible buildings PY - 2024 SN - 978-90-90-39058-1 SN - 2329-3675 SP - 1 EP - 8 AN - OPUS4-61245 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baer, Wolfram A1 - Wossidlo, Peter A1 - Abbasi, Behboud A1 - Cassau, Matthias ED - Borsutzki, M. ED - Moninger, G. T1 - Zur Auswertung und Verwendung von Kerbschlagbiegeversuchsergebnissen - Fehler und Defizite in relevanten Normen N2 - Der Kerbschlagbiegeversuch ist als Prüfverfahren seit langem international genormt. Zu garantierende Kerbschlagarbeitswerte sind in Produktnormen weltweit festgelegt. Gleichwohl enthalten ganze Normenreihen für Stähle falsche Festlegungen zur Verwendung von Untermaßprobenergebnissen. Im Mittelpunkt der vorliegenden Studie stehen die Auswertung von KV-T-Daten und die Skalierung von Untermaßprobenergebnissen. Hierzu wurden an ISO-V-Proben der Breiten 2,5; 5; 7,5 und 10 mm aus vier Baustählen im Streckgrenzenbereich von 235 bis 960 MPa dicht belegte KV-T-Kurven ermittelt. Es wurden unterschiedliche Vorgehensweisen zur Kurvenanpassung und Festlegung von Übergangstemperaturen wie auch der Hoch- bzw. Tieflagenarbeit untersucht. Die Ergebnisse unterstreichen unter anderem, dass die in festgelegte Vorgehensweise, nach der Untermaßprobenergebnisse proportional auf Normprobenmaße zu skalieren sind, nicht nur zu falschen, sondern auch nicht-konservativen Kerbschlagarbeitswerten führen kann. Das Ausmaß dieses Probenbreiteneffektes ist Werkstoff- und temperaturabhängig. Da die Kerbschlagarbeit als Abnahmekriterium verwendet wird, ergeben sich unmittelbare wirtschaftliche und sicherheitstechnische Konsequenzen. Es ist zu schlussfolgern, dass die entsprechenden Produktnormenreihen dringend zu überarbeiten sind. T2 - Tagung Werkstoffprüfung 2014 - Fortschritte in der Werkstoffprüfung für Forschung und Praxis CY - Bad Neuenahr, Germany DA - 03.12.2015 KW - Kerbschlagbiegeversuch KW - Untermaßproben KW - Bewertung PY - 2015 SN - 978-3-514-00816-8 SP - 181 EP - 186 PB - Verlag Stahleisen CY - Düsseldorf AN - OPUS4-35082 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kocherla, Amarteja A1 - Strangfeld, Christoph A1 - Hüsken, Götz T1 - Embedded Sensors for Quality Control and Structural Integrity Monitoring of Large-scale 3DCP Structures N2 - In extrusion-based 3D concrete printing (3DCP), addressing challenges related to safety, reliability, and quality control is crucial for widespread adoption. Yet current limitations in monitoring material properties during and after printing hinder the development of effective 3DCP guidelines. Therefore, the development of an inline sensing system capable of real-time monitoring and adjustment of process parameters is necessary to overcome these challenges. Building upon an existing inline sensing system developed by BAM, which currently monitors material properties during printing and the geometry of the print post-extrusion, this study extends its capabilities to post-extrusion monitoring using embedded piezoelectric (PZT) sensors. These PZT sensors provide localized measurements of material changes through electrical impedance (EI) measurements without disrupting the printing process. By embedding these sensors in 3D printed structures, continuous monitoring is achieved from layer deposition through 1-day of hydration. To achieve this, initially, PZT sensors were developed with multiple layers of protective coatings. Two different 3D printed mixtures, each with different hydration behaviors, were utilized, and PZT sensors were strategically placed between printed layers to maintain their integrity. EI measurements were collected continuously from printing through 1 day of hydration. Analysis of amplitude and frequency changes in the EI response spectrum provided insights into material behavior post-printing. The study highlights how continuous monitoring of frequency and conductance can track structural builtup and property development of the material. Rapid changes in conductance measurements, immediately post-printing indicate swift structural built-up, while key hydration phases are reflected in frequency measurements. T2 - 34th Annual Conference and Exhibition on Non Destructive Evaluation & Enabling Technologies CY - Chennai, India DA - 12.12.2024 KW - Embedded Sensors KW - 3D Concrete Printing KW - Quality Control KW - Inline Sensing KW - Structural Integrity PY - 2025 SP - 1 EP - 8 PB - Springer Nature CY - Heidelberg AN - OPUS4-65305 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Detjens, Marc A1 - Hübert, Thomas A1 - Tiebe, Carlo A1 - Banach, Ulrich T1 - Temperature influence on coulometric trace humidity measurement N2 - Planar coulometric sensors were tested in humidified synthetic air at various gas temperatures. Generated frost point temperature in the gas ranged from -30 °C to -60 °C and were measured by coulometric sensors and in addition by a calibrated dew point hygrometer. The gas temperatures, which were measured by a calibrated Pt100 sensor, were set to -20 °C, 0 °C, 23 °C, 40 °C, 50 °C, and 60 °C during the experiments. Empiric nonlinear functions were calculated between the generated humidity and the sensor signals. In comparison to the measured signals at 23 °C, the sensor signals were lower at the other gas temperatures. The measurements at 60 °C showed indistinct results due to a great signal noise. The response behavior of the sensors was similar at 23 °C, 40 °C and 50 °C. In contrast to that, the sensors reacted slowly at a gas temperature of -20 °C and 0 °C. In summary, with coulometric sensors it was possible to measure continuously trace humidity with an expanded uncertainty below 2 K. T2 - IEEE Sensors 2017 CY - Glasgow, Scotland, UK DA - 30.10.2017 KW - Response behavior KW - Coulometric sensors KW - Trace humidity measurement KW - Temperature influence KW - Chemical reaction PY - 2017 SN - 978-1-5386-4056-2 SP - 1308 EP - 1310 PB - IEEE CY - Piscataway, NJ, USA AN - OPUS4-43241 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Theiler, Geraldine A1 - Gradt, Thomas T1 - Friction and wear characteristics of polymers in gaseous and liquid hydrogen N2 - The tribological characteristics of pure and graphite filled polymers were investigated in gaseous hydrogen at ambient temperatures and in LH2 at -253°C. It could be shown that the tribological properties of PI and PEEK materials is related to the formation of a transfer film. The influence of both hydrogen and cryogenic temperatures will be discussed in the presentation. T2 - 21th International Colloquium Tribology CY - Stuttgart/Ostfildern, Germany DA - 09.11.2018 KW - Friction KW - Wear KW - Hydrogen KW - PEEK PY - 2018 SP - 1 EP - 2 AN - OPUS4-43903 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zeps, Robert A1 - Rosenow, B. A1 - Kluge, Martin A1 - Blanchard, R. A1 - Holtappels, Kai T1 - Druckentlastungsvorgänge in großvolumigen Behältern N2 - Es wurden Druckentlastungsvorgänge in einem 5 m³ Autoklav mit einem L/D-Verhältnis von 1,14 nach der Zündung von Methan-Luft-Gemischen untersucht. Schwerpunkt der Arbeit war die Bestimmung der Explosionsdrücke, der zeitlichen Druckanstiege bzw. der KG-Werte und der reduzierten Explosionsdrücke in Abhängigkeit der Methankonzentration. Im geschlossenen Behälter wurden die Explosionsdrücke und zeitlichen Druckanstiege für Methan-Luft-Gemische mit Methankonzentrationen von 5,9 Vol-% bis 13,5 Vol-% ermittelt. Die Ergebnisse zeigen gute Übereinstimmung mit den Literaturwerten. Weiter wurden Druckentlastungsversuche mit einer kreisrunden Entlastungsfläche von 0,011 m² und einer Druckentlastungsfolie mit einem statischen Ansprechdruck von 1,94 bar durchgeführt. Hierbei wurden Gemische mit Methankonzentrationen von 5,9 Vol-% bis 14,3 Vol-% untersucht. Dabei zeigte sich, dass die vergleichsweise kleine Entlastungsfläche nur dann zu reduzierten Explosionsdrücken gleich dem statischen Ansprechdruck der Berstfolie führte, wenn die Methankonzentration ≤ 5,9 Vol-% oder ≥ 14,0 Vol-% betrug. Bei allen anderen untersuchten Methankonzentrationen führten die durch die Druckentlastung induzierten Turbulenzen zu einer Beschleunigung der Verbrennungsreaktion und zu Explosionsdrücken vergleichbar denen im geschlossenen Behälter. T2 - 14. Kolloquium zur chemischen und physikalischen Sicherheitstechnik (BAM-PTB-Kolloquium) CY - Berlin, Germany DA - 14.06.2016 KW - Druckentlastung KW - Up-Scale KW - Deflagration KW - Sicherheitstechnik PY - 2016 SN - 978-3-9817853-5-7 SN - 0938-5533 VL - 2016 SP - 21 EP - 28 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-37176 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lichtenstein, D. A1 - Böhmert, L. A1 - Meyer, Th. A1 - Sieg, H. A1 - Thünemann, Andreas A1 - Loipis, I. E. A1 - Bäuning, A. A1 - Lampen, A. T1 - Core or coating material? What dictates the uptake and translocation of nanoparticles in vitro? N2 - A core-dependent effect on nanoparticle translocation was revealed. Both the uptake and transport of nanoparticles in and through cells should be considered when discussing nanoparticle fate and safety. T2 - 52nd Congress of the European-Societies-of-Toxicology (EUROTOX) CY - Seville, Spain DA - 04.09.2016 KW - Small-angle X-ray scattering KW - SAXS KW - Silver KW - Nanoparticle PY - 2017 DO - https://doi.org/10.1016/j.toxlet.2016.06.1940 SN - 0378-4274 SN - 1879-3169 VL - 258 SP - S267 EP - S268 PB - Elsevier Ltd. AN - OPUS4-40935 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hausberger, A. A1 - Major, Z. A1 - Theiler, Geraldine A1 - Gradt, Thomas A1 - Schwarz, T. T1 - Investigation on the friction and wear behaviour of thermoplastic polyurethanes by controlling the adhesion and deformation part of friction N2 - In this work, unfilled and graphite filled TPU materials were used to investigate the contribution of the adhesion and deformation component of friction. Pin-on-Disc tests were conducted in the air and under vacuum condition by using different surface roughness. T2 - 6. European Conference on Tribology CY - Ljubljana, Slovenia DA - 07.06.2017 KW - TPU KW - Friction KW - Wear KW - Adhesion KW - Deformation KW - Vacuum PY - 2017 SP - 4.02 - 1 EP - 4.02 - 2 AN - OPUS4-40763 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baensch, Franziska A1 - Hofmann, Detlef A1 - Johann, Sergej A1 - Tiebe, Carlo A1 - Basedau, Frank A1 - Sturm, Patrick A1 - Lay, Vera A1 - Niederleithinger, Ernst T1 - Multi-sensor conception for safe sealing structures in underground repositories N2 - The project "SealWasteSafe" of the Bundesanstalt für Materialforschung und -prüfung (BAM, Berlin) deals with sealing structures applied for underground disposal of nuclear waste from two perspectives: (1) material improvement for application in sealing constructions and (2) feasibility study regarding multi-sensor approaches to ensure quality assurance and long-term monitoring. One specimen of 150 l made of alkali-activated material, which was found innovative and suitable for sealing constructions based on preliminary laboratory studies, and, for comparison purpose, another one made of salt concrete, are manufactured with an integrated multi-sensory setup for quality assurance and long-term-monitoring. The specimens were left in their cast form and additionally thermally insulated to simulate the situation in the repository. The multi-sensory concept comprises RFID technology embedded in the specimens suppling material temperature and moisture measurements, integrated fibre optic sensing allowing strain measurement and acoustic emission testing for monitoring possible crack formation. Overall, the suitability and the functionality of the sensors embedded into and attached to strongly alkaline (pH > 13 for the AAM) and salt corrosive (NaCl) environment was proven for the first 672 h. First temperature measurement based on RFID succeeded after 626 h for the alkali-activated material and after 192 h for the conventional salt concrete. Strain measurement based on distributed fibre optic sensing turned out the alkali-activated material with > 1 mm m-1 undergoing approximately twice the compression strain as the salt concrete with strains < 0.5 mm m-1. In contrast, the acoustic emission first and single hits representing crack formation in numbers, was found for alkali-activated material half of that detected at the salt concrete. T2 - SMIRT 26 CY - Berlin/Potsdam, Germany DA - 10.07.2022 KW - SealWasteSafe KW - Monitoring KW - Acoustic emission KW - Fibre optic sensing KW - RFID technology KW - alkali-activated material PY - 2022 SP - 1 EP - 10 AN - OPUS4-55371 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -