TY - CONF A1 - Lohrke, Heiko A1 - Kohlhoff, Harald A1 - Erdmann, Jessica A1 - Winkler, Nicolas P. A1 - Neumann, Patrick P. T1 - Combined GNSS/Visual Inter-Robot Tracking Method for Open-Path Gas Tomography N2 - Methane emissions are a significant environmental and safety concern, yet many gas tomography systems intended to measure them require manual alignment, reliable high-bandwidth links, or fiducials. We present a lightweight, fully autonomous framework enabling line-of-sight inter-robot Tunable Diode Laser Absorption Spectroscopy (TDLAS) measurements without such constraints. A sensor robot equipped with a gimbal-mounted TDLAS unit tracks a reflector robot bearing an illuminated, color-controllable target. Coarse localization is achieved via RTK-GNSS, with vision-based fine tracking and passive time synchronization handled onboard. The system, based on off-the-shelf Pixhawk controllers and ArduPilot firmware, was validated in a 15m × 7m outdoor trial. Despite GNSS inaccuracies and deliberate occlusion by a methane-filled bag, the system retained lock, recovered from visual loss in under one second, and captured a 2800 ppm·m plume signature. These results demonstrate robust, scalable methane sensing for mobile gas tomography or standalone leak detection. Core components are released open-source to support future deployment. T2 - IEEE SENSORS 2025 CY - Vancouver, BC, Kanada DA - 19.10.2025 KW - Gas tomography KW - Tracking KW - Robot KW - Methane KW - TDLAS PY - 2025 SN - 979-8-3315-4467-6 DO - https://doi.org/10.1109/SENSORS59705.2025.11330519 SP - 1 EP - 4 PB - IEEE CY - Piscataway, NJ, USA AN - OPUS4-65615 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Karafiludis, Stephanos A1 - de Oliveira Guilherme Buzanich, Ana A1 - Kochovski, Z. A1 - Feldmann, Ines A1 - Emmerling, Franziska A1 - Stawski, Tomasz T1 - Ni- and Co-Struvites: Revealing Crystallization Mechanisms and Crystal Engineering toward Applicational Use of Transition Metal Phosphates N2 - Industrial and agricultural waste streams (waste water, sludges, tailings, etc.) which contain high concentrations of NH4+, PO43–, and transition metals are environmentally harmful and toxic pollutants. At the same time, phosphorous and transition metals constitute highly valuable resources. Typically, separate pathways have been considered to extract hazardous transition metals or phosphate independently from each other. Investigations on the simultaneous removal of multiple components have been carried out only to a limited extent. Here, we report the synthesis routes for Ni- and Co-struvites (NH4MPO4·6H2O, M = Ni2+ and Co2+), which allow for P, ammonia, and metal co-precipitation. By evaluating different reaction parameters, the phase and stability of transition metal struvites as well as their crystal morphologies and sizes could be optimized. Ni-struvite is stable in a wide reactant concentration range and at different metal/phosphorus (M/P) ratios, whereas Co-struvite only forms at low M/P ratios. Detailed investigations of the precipitation process using ex situ and in situ techniques provided insights into the crystallization mechanisms/crystal engineering of these materials. M-struvites crystallize via intermediate colloidal amorphous nanophases, which subsequently aggregate and condense to final crystals after extended reaction times. However, the exact reaction kinetics of the formation of a final crystalline product varies significantly depending on the involved metal cation in the precipitation process: several seconds (Mg) to minutes (Ni) to hours (Co). The achieved level of control over the morphology and size makes precipitation of transition metal struvites a promising method for direct metal recovery and binding them in the form of valuable phosphate raw materials. Under this paradigm, the crystals can be potentially up-cycled as precursor powders for electrochemical or (electro)catalytic applications, which require transition metal phosphates. KW - Crystallization KW - Struvite KW - Nickel KW - Cobalt KW - Phosphorous recovery KW - Up-cycling KW - Aqueous synthesis PY - 2022 DO - https://doi.org/10.1021/acs.cgd.2c00284 VL - 22 IS - 7 SP - 4305 EP - 4315 PB - ACS Publications CY - Washington D.C. AN - OPUS4-55286 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bach, S. A1 - Visnow, E. A1 - Panthöfer, M. A1 - Gorelik, T. A1 - de Oliveira Guilherme Buzanich, Ana A1 - Gulo, A. A1 - Kolb, U. A1 - Emmerling, Franziska A1 - Lind, C. A1 - Tremel, W. T1 - Hydrate networks under mechanical stress – A case study for Co3(PO4)2·8H2O N2 - The nature of the bound water in solids with hydrogen-bonded networks depends not only on temperature and pressure but also on the nature of the constituents. The collapse and reorientation of these network structures determines the stability of hydrated solids and transitions to other crystalline or amorphous phases. Here, we study the mechanochemically induced loss of bound water in Co₃(PO₄)₂·8H₂O and compare this process to the behavior under hydrostatic pressure. The associated phase transition and its kinetics were monitored by X-ray powder diffraction with Synchrotron radiation and quantitative IR spectroscopy. High shearing forces are responsible for the degradation of the hydrogen-bonded network and the concomitant crystalline–amorphous transformation. UV/Vis spectroscopy, extended X-ray absorption spectroscopy (EXAFS), and X-ray absorption near-edge spectroscopy (XANES) provided information about the short-range order in the amorphous solid, and thermal analysis revealed its composition and showed that the moderate charge densities of the Co²⁺ and PO₄³⁻ ions, which make the hydration enthalpy comparable to the binding energy of the counteranions, and the Formation of hydrogen-bonded networks favor multistage crystallization processes associated with the release and uptake of coordinated water. The changes of the Co²⁺ coordination induce a color change from pink to blue; therefore, Co₃(PO₄)₂·8H₂O can be used as an overheat temperature indicator. KW - Mechanochemistry KW - Amorphous materials KW - Hydrates KW - Cobalt KW - Phosphates PY - 2016 DO - https://doi.org/10.1002/ejic.201501481 SN - 1434-1948 SN - 1099-0682 VL - 2016 IS - 13-14 SP - 2072 EP - 2081 PB - Wiley-VCH Verlag GmbH & Co. KGaA CY - Weinheim, Germany AN - OPUS4-36434 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cakir, Cafer Tufan T1 - Bayesian optimization for depth resolved analysis of complex alloys with grazing exit XANES N2 - Compositionally complex alloys (CCAs) are a new class of alloys containing at least 5 elements with concentrations between 5 and 35 atomic percent. Due to their adjustable composition, which enables modifications of mechanical properties (such as hardness, strength and ductility etc) and their stability at high temperatures, CCAs have been the focus of various studies [1,2]. Especially the corrosion behavior of CCAs has been a wide research interest. However, there are only few studies that deals with the degradation process on such materials, which is highly relevant for the safety aspect for future component design. To thoroughly investigate the corrosion processes and to determine oxidation states of metal components within the reaction products, we need special analytical tools. Since the grazing exit X-ray fluorescence (GEXRF) offers a non-destructive way to collect notable information regarding the high temperature oxidation, we consider it as a useful method to investigate how CCAs behave in corrosive environments. The main idea of grazing geometry is to enhance the fluorescence signal of the surface. This enables highly sensitive surface analyses of thin protective film on surface in sub-micrometer scale [3]. When compared to a conventional CCD-based camera, the advantage and most important feature of the detector system (Color X-Ray Camera (CXC)) is that each pixel is an energy sensitive detector. The position and area sensitive detector, with 264x264 pixel detector area, provides information regarding the signal emitted from the sample as a function of the emission angle and thus allows depth-sensitive analysis. Furthermore, the data collected from samples of an incidence energy which can be controlled with a resolution of 0.5 eV provides XANES data to determine oxidation states. In this contribution, we address the feasibility of our setup and new optimization procedure (Bayesian Optimization and Gaussian Regression). The results of a conceptual study regarding layer properties of the reference sample (Cr-Oxide layer (300nm) on Cr layer (500nm) on Si wafer) and CrCoNi (Cr-Oxide (>1µm) layer on CrCoNi substrate) medium entropy alloy. T2 - European Conference on X-ray Spectrometry. EXRS 2022 CY - Bruges, Belgium DA - 26.06.2022 KW - GEXRF KW - High entropy alloys KW - XANES KW - Grazing exit KW - High entropy materials KW - XAS KW - Optimization PY - 2022 AN - OPUS4-56272 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Emmerling, Franziska T1 - In situ characterization of nucleation, growth, crystallization and dissolution of nanoscaled iron oxides N2 - Nucleation and growths of iorn oxide nanoparticles studied in situ using XRD, XRF, SAXS and XANES. T2 - International CRC meeting CY - Berlin, Germany DA - 10.10.2018 KW - XRD KW - XANES PY - 2018 AN - OPUS4-46995 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Pakrashy, Sourav A1 - Chakraborty, Souvik A1 - Manna, Sounik A1 - Nanda Goswami, Juli A1 - Bhattacharya, Biswajit A1 - Emmerling, Franziska A1 - Mandal, Jishu A1 - Misra, Sourav A1 - Maiti Choudhury, Sujata A1 - Okla, Mohammad K. A1 - Bose, Adity A1 - Maurya, Pawan Kumar A1 - Majhi, Anjoy A1 - Dolai, Malay T1 - Inhibition of Human Colorectal Cancer by a Natural Product 7-Acetylhorminone and Interactions with BSA/HSA: Multispectral Analysis and In Silico and In Vitro Studies N2 - We have semi-synthesized a natural product 7-acetylhorminone from crude extract of Premna obtusifolia (Indian headache tree), which is active against colorectal cancer after probation through computational screening methods as it passed through the set parameters of pharmacokinetics (most important nonblood–brain barrier permeant) and drug likeliness (e.g., Lipinski’s, Ghose’s, Veber’s rule) which most other phytoconstituents failed to pass combined with docking with EGFR protein which is highly upregulated in the colorectal carcinoma cell. The structure of 7-acetylhorminone was confirmed by single crystal X-ray diffraction studies and 1H NMR, 13C NMR, and COSY studies. To validate the theoretical studies, first, in vitro experiments were carried out against human colorectal carcinoma cell lines (HCT116) which revealed the potent cytotoxic efficacy of 7-acetylhorminone and verified preliminary investigation. Second, the drugability of 7-acetylhorminone interaction with serum albumin proteins (HSA and BSA) is evaluated both theoretically and experimentally via steady-state fluorescence spectroscopic studies, circular dichroism, isothermal titration calorimetry, and molecular docking. In summary, this study reveals the applicability of 7-acetylhorminone as a potent drug candidate or as a combinatorial drug against colorectal cancer. KW - Molecular docking KW - In situ synthesis KW - ADMET PY - 2024 DO - https://doi.org/10.1021/acsabm.4c00335 VL - 7 IS - 5 SP - 3414 EP - 3430 PB - American Chemical Society (ACS) AN - OPUS4-61114 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Parthasarathy, Thiyagaraj A1 - Mishra, Manish Kumar A1 - Bhattacharya, Biswajit A1 - Emmerling, Franziska A1 - Ghosh, Soumyajit T1 - Simultaneously Mechanically Flexible, Photobending, and Acidochromic Cyanostilbene Molecular Crystals N2 - Molecular crystals that respond to multiple stimuli are gaining significant attention for their potential in smart materials like actuators and sensors. However, imparting multiple stimuli-responsive properties to a single crystal remains a major challenge. Herein, we report two cyanostilbene derivative-based crystals 1 and 2, with various responses to stimuli such as mechanical stress, light, acid vapors, etc. Both crystals 1 and 2 demonstrated mechanical flexibility and reversible acidochromism. Additionally, crystal 1 also exhibited light-induced photobending, which is ascribed to Z to E photoisomerization. Detailed structure–property correlation was established to unravel distinct mechanical responses. The development of these multitasking crystals may find applications in multitasking actuators, anticounterfeiting materials, and more. KW - Absorption KW - Crystals KW - Mechanical flexiblity KW - Photoisomerization PY - 2025 DO - https://doi.org/10.1021/acs.cgd.4c01341 VL - 25 IS - 2 SP - 309 EP - 318 PB - American Chemical Society (ACS) AN - OPUS4-62568 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Michalchuk, Adam A1 - Emmerling, Franziska T1 - Time-Resolved InSitu Monitoring of Mechanochemical Reactions N2 - Mechanochemical transformations offer environmentally benign synthesis routes, whilst enhancing both the speed and selec-tivity of reactions. In this light, mechanochemistry promises to trans-form the way in which chemistry is done in both academia and indus-try but is greatly hindered by a current lack in mechanistic understand-ing. The continued development and use of time-resolved in situ(TRIS) approaches to monitor mechanochemical reactions provides a new dimension to elucidatethese fascinating transformations. We here discuss recent trends in method development that have pushed the boundaries of mechanochemical research. New features of mech-anochemical reactions obtained by TRIS techniques are subse-quently discussed, shedding light on how different TRISapproaches have beenused. Emphasis is placed on the strength of combining complementary techniques. Finally, we outline our views for the po-tential of TRIS methods in mechanochemical research, towards es-tablishing a new, environmentally benign paradigm in the chemical sciences KW - Mechanochemistry KW - Material synthesis KW - Green chemistry PY - 2022 DO - https://doi.org/10.1002/anie.202117270 SN - 1433-7851 SP - 1 EP - 15 PB - Wiley-VCH CY - Weinheim AN - OPUS4-54321 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Fischer, Franziska A1 - Joester, Maike A1 - Rademann, K. A1 - Emmerling, Franziska T1 - Survival of the fittest: competitive co-crystal reactions in the ball mill N2 - The driving forces triggering the formation of co-crystals under milling conditions were investigated by using a set of multicomponent competitive milling reactions. In these reactions, different active pharmaceutical ingredients were ground together with a further compound acting as coformer. The study was based on new co-crystals including the coformer anthranilic acid. The results of the competitive milling reactions indicate that the formation of co-crystals driven by intermolecular recognition are influenced and inhibited by kinetic aspects including the formation of intermediates and the stability of the reactants. PY - 2015 DO - https://doi.org/10.1002/chem.201500925 SN - 0947-6539 SN - 1521-3765 VL - 21 IS - 42 SP - 14969 EP - 14974 PB - Wiley-VCH Verl. CY - Weinheim AN - OPUS4-34861 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Production of small micro- and nanoplastic reference materials supporting harmonization and standardization N2 - The MICROPLASTICdays at Ljubliana, Slowenia, were organized in cooperation with the PRIORITY cost action. The topic has been reference materials this time. The talk gives an idea of the preparation of reference materials in micro- and nanoplastic topic to support standardisation and regulation. It defines the term of micro-and nanoplastics and presents different case studies and critical attributes to the production depending on the enduser needs. T2 - MICROPLASTICdays CY - Ljubljana, Slovenia DA - 25.03.2025 KW - Microplastics KW - Nanoplastics KW - Reference materials PY - 2025 AN - OPUS4-62801 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Microplastic occurrence in urban sewage systems: Identification of sources for pathways into the environment N2 - All over the world, microplastic (MP) particles (particle size: 1 - 1.000 µm) are found in water, soil, air, biota and even food products. But plenty of these discussed findings are based on a very low number of real datasets, which are extrapolated to general projections. Furthermore, most data are not comparable because the strategies for sampling, sample preparation and detection methods are not harmonised/ or standardised. This would require extensive proficiancy tests. Because of the ubiquity presence and the unclear risks, which might arise from those particles, various political and environmental organisations (i.e. OECD, UNEP, WHO) identify the reduction of plastic entry in the environment as a key challenge for now and the future. This challenge includes the identification of relevant entry pathways but also the demand of harmonised, meaningful and reliable analytical procedures. Regarding this task within the last few years, a fast practical solution for MP analysis has been developed, which includes the steps of representative sampling, adequate sample preparation and fast detection. Sampling is done by fractional filtration over sieves with mesh sizes of 500, 100, 50 and 5 µm [1]. The received samples are measured by ThermoExtraction/Desorption-Gas Chromatography-Mass Spectrometry (TED-GC-MS) [1,2]. for the most abundant polymers used in practice, which are polyethylene (PE), polypropylene (PP), polystyrene (PS), polyethylene terephthalate (PET), polyamide (PA) and acrylate as well as styrene-butadiene-rubber (SBR), a main component of tires. The present presentation will give first-time insight in a comprehensive dataset of microplastic analysis for an exemplary urban sewage system. MP mass contents of different waters at several days, such as greywater, stormwater retention tank, influent and effluent of a wastewater treatment plant (WWTP) within an urban sewage system in Germany are determined. Furthermore, the mass of the polymers found in dry weather and rain weather flow are compared. The use of these large datasets allows first expressive conclusions regarding the contribution of urban sewage system to the MP entry sources in the environments. We found PP and PS in all different waters. Furthermore, there is SBR in influent and also in effluent of the WWTP. Surprisingly, we could also detect hugh amounts of PE in the effluent of the WWTP. T2 - SETAC Europe 2020 CY - Online meeting DA - 03.05.2020 KW - Microplastic analysis KW - TED-GC/MS KW - Microplastic particles KW - Microplastic mass contents PY - 2020 AN - OPUS4-50795 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bhattacharya, Biswajit A1 - Akhmetova, Irina A1 - Rautenberg, Max A1 - Emmerling, Franziska T1 - Mechanochemical synthesis of phosphonate-based proton conducting metal organic frameworks and hydrogen-bonded metal phosphonates N2 - Proton exchange membrane fuel cells (PEMFCs) are one of the most promising alternative green energy technologies that deliver high energy density without CO2 emissions. The proton conductivity of proton exchange membranes (PEM) contributes to the overall efficiency of a PEMFC. Materials being used as PEMs must exhibit high proton conductivity at the working conditions of the targeted PEMFC. To date, Nafion and Nafion-like polymers with acidic functionality are widely used as membrane materials due to their high proton conductivity in the range of 10-1 to 10-2 Scm-1 at higher relative humidity. However, these materials suffer from high costs, hazardous production process, and poor performance at high temperatures, limiting their versatility. In this context, crystalline porous materials are recognized as promising proton conductors for the proton exchange membrane (PEM) in fuel cell technology, owing to their tunable framework structure. However, it is still challenging bulk synthesis for real-world applications of these materials. Herein, we present mechanochemical gram-scale synthesis of series of mixed ligand metal organic frameworks (MOFs) and metal hydrogen‐bonded organic frameworks (MHOFs) using phenylene diphosphonic acid and 1-hydroxyethylidene-1,1-diphosphonic acid with different bipyridyl type of ligands, respectively. In all cases, the existence of extensive hydrogen bonds with amphiprotic uncoordinated phosphonate hydroxyl and oxygen atoms, the frameworks exhibited high proton conductivity. The study demonstrates the potential of green mechanosynthesis for preparations of framework-based proton conducting materials in bulk scale for green energy generation. T2 - 4th International Conference on Phosphonate Chemistry, Science and Technology, ICOPHOS-4 CY - Crete, Greece DA - 02.10.2023 KW - Proton exchange membrane fuel cells KW - Metal organic frameworks KW - Proton conducting materials PY - 2023 AN - OPUS4-58837 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heinekamp, Christian T1 - Exploring amorphous lewis-acidic zirconium chloro fluoride as a heterogeneous HF shuttle N2 - Owing to a growing shortage of fluorspar, a raw material used for producing fluorinated base chemicals, fluorspar has been named among the 30 critical raw materials in the EU. 1 However, the sustainable transfer of fluorine atoms from one molecule to another using heterogeneous catalysts has not yet been reported. Herein, we present the heterogeneous catalyst zirconium chloro fluoride (ZCF) that performs dehydrofluorination of a fluoroalkane and consecutive hydrofluorination of an alkyne at room temperature. T2 - Make and Measure 2023 CY - Berlin, Germany DA - 13.09.2023 KW - ZCF KW - Heterogeneous catalysis KW - C-F bond activation KW - HF-shuttle PY - 2023 AN - OPUS4-59616 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kulow, Anicó A1 - de Oliveira Guilherme Buzanich, Ana A1 - Reinholz, Uwe A1 - Emmerling, Franziska A1 - Hampel, S. A1 - Fittschen, U.E.A. A1 - Streli, C. A1 - Radtke, Martin T1 - Comparison of three reconstruction methods based on deconvolution, iterative algorithm and neural network for X-ray fluorescence imaging with coded apertures N2 - X-ray imaging methods are used in many fields of research, as they allow a non-destructive Investigation of the elemental content of various samples. As for every imaging method, for X-ray imaging the optics are of crucial importance. However, these optics can be very expensive and laborious to build, as the requirements on surface roughness and precision are extremely high. Angles of reflection and refraction are often in the range of a few mrad, making a compact design hard to achieve. In this work we present a possibility to simplify X-ray imaging. We have adapted the coded aperture method, a high energy radiation imaging method that has its origins in astrophysics, to full field X-ray fluorescence imaging. In coded aperture imaging, an object is projected through a known mask, the coded aperture, onto an area sensitive detector. The resulting image consists of overlapping projections of the object and a reconstruction step is necessary to obtain the information from the recorded image. We recorded fluorescence images of different samples with an energy-dispersive 2D detector (pnCCD) and investigated different reconstruction methods. With a small coded aperture with 12 holes we could significantly increase the count rate compared to measurements with a straight polycapillary optic. We show that the reconstruction of two different samples is possible with a deconvolution approach, an iterative algorithm and a neural network. These results demonstrate that X-ray fluorescence imaging with coded apertures has the potential to deliver good results without scanning and with an improved count rate, so that measurement times can be shortened compared to established methods. KW - X-ray fluorescence imaging KW - Coded apertures KW - Imaging KW - Elemental mapping KW - Image reconstruction PY - 2020 DO - https://doi.org/10.1039/d0ja00146e VL - 35 IS - 7 SP - 1423 EP - 1434 PB - Royal Society of Chemistry CY - United Kingdom AN - OPUS4-51518 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Al-Terkawi, Abdal-Azim A1 - Prinz, Carsten A1 - Scholz, Gudrun A1 - Kemnitz, Erhard A1 - Emmerling, Franziska T1 - Ca-, Sr-, and Ba-Coordination polymers based on anthranilic acid via mechanochemistry N2 - Ca-, Sr-, and Ba-Based coordination polymers (CPs) were prepared mechanochemically by milling metal-hydroxide samples with anthranilic acid (oABAH). {[Ca(oABA)2(H2O)3]}n consists of one-dimensional polymeric chains that are further connected by a hydrogen-bonding network. {[Sr(oABA)2(H2O)2]·H2O}n is a one-dimensional CP in which water molecules bridge Sr2+ ions and increase the dimensionality by building an extended network. {[Ba(oABA)2(H2O)]}n crystallizes as a two-dimensional CP comprising one bridging water molecule. The cation radii influence the inorganic connectivity and dimensionality of the resulting crystal structures. The crystal structures were refined from powder X-ray diffraction data using the Rietveld method. The local coordination environments were studied via extended X-ray absorption fine structure (EXAFS) measurements. The compounds were further characterized using comprehensive analytical methods such as elemental analysis, thermal analysis, MAS NMR, imaging, and dynamic vapor sorption (DVS) measurements. Compounds 1, 2, and 3 exhibit small surface areas which decrease further after thermal annealing experiments. All compounds exhibit a phase transformation upon heating, which is only reversible in 3. KW - Mechanochemistry KW - XRD PY - 2019 DO - https://doi.org/10.1039/c9dt00991d SN - 1477-9226 SN - 1477-9234 VL - 48 IS - 19 SP - 6513 EP - 6521 PB - Royal Society of Chemistry AN - OPUS4-48014 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Beyer, Sebastian A1 - Prinz, Carsten A1 - Schürmann, Robin A1 - Feldmann, Ines A1 - Zimathies, Annett A1 - Blocki, Anna A1 - Bald, Ilko A1 - Schneider, Rudolf A1 - Emmerling, Franziska T1 - Ultra-sonication of ZIF-67 crystals results in ZIF-67 nano-flakes N2 - Zeolitic Imidazolate Frameworks (ZIFs) are crystalline materials that comprise of metal nodes and Imidazole derivatives as linkers. ZIF-67 is often used in polymer composite materials e. g. for gas separation membranes. Post-synthesis treatment of ZIF-67 crystals with ultrasound leads to unforeseen plasticity that resulted in sintered ZIF-67 and ZIF-67 nano-flakes. Consequently, ultrasound increases the external surface area of ZIF-67 which might improve e.g. blending with polymers in composite materials. These new morphologies of ZIF-67 were characterized by transmission electron, scanning electron, and atomic force microscopy. The ultrasound treatment of ZIF-67 did not result in the formation of an amorphous framework or a meta-stable crystal structure as indicated by powder x-ray diffraction. In addition, ultra-sonicated ZIF-67 retained the high gas adsorption capacity and pore size compared to synthesized ZIF-67. The morphological changes are hard to detect with standard analytical methods that are usually utilized for MOF characterization. These findings also suggest that sonochemical treatment of ZIFs leads to structural effects beyond increasing the amount of nucleation clusters during sono-chemical synthesis, which is currently not addressed in the field. KW - ZIF PY - 2016 DO - https://doi.org/10.1002/slct.201601513 SN - 2365-6549 VL - 1 IS - 18 SP - 5905 EP - 5908 AN - OPUS4-38496 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kittner, Maria T1 - Development of a new Lysimeter System to assess Microplastic, PAH & Heavy Metal Emissions from Artificial Turf Sports Pitches N2 - Since September 2023, the European Commission introduced a new regulation to reduce emissions of microplastics (MP) into the environment, including the sale and use of intentionally added MP. Therein, the use of synthetic rubber granules in artificial turf is explicitly mentioned and banned for future use. Additionally, abrasions of grass fibres and other turf components are also considered as MP sources. Artificial turf pitches are multi component systems: e. g. grass fibres made of polyethylene (PE), synthetic infill made of ethylene propylene diene monomer rubber (EPDM), carpet backing of polypropylene (PP) glued with polyurethane (PU), winding yarn of polyethylene terephthalate or elastic layer of Styrene-butadiene rubber (SBR) bound with PU. While the ban has great impact on recreational sports, there is so far no sufficient data to estimate the MP emissions from artificial turf sports pitches into the environment and thus their relevance as a source of MP pollution. To close this gap, three artificial turf scenarios in different ageing states (unaged, artificially aged and aged in real time) were analysed in this study: the past (old turf: fossil based, synthetic infill), present (most commonly installed in Germany: fossil based, synthetic infill) and future (turf with recycled grass fibres, no synthetic infill). To simulate outdoor weathering during the service life of approx. 15 years, accelerated ageing by UV weathering and mechanical stress was carried out. The newly developed and in-house manufactured Microplastic Eluate Lysimeter (MEL) simulates contaminant transfer into the groundwater and allows the simultaneous sampling for MP and dissolved contaminants, like polycyclic aromatic hydrocarbons (PAH) or heavy metals (HM). MP mass contents were analysed using smart microfilter crucibles (mesh size: 5 µm) and Thermal Extraction Desorption Gas Chromatography/Mass Spectrometry and PAH and HM concentrations were determined using Gas Chromatography/Mass Spectrometry or Inductively Coupled Plasma Atomic Emission Spectroscopy, respectively. T2 - MICRO2024: Plastic Pollution from Micro to Nano CY - Arrecife, Spain DA - 23.09.2024 KW - Microplastics Eluate Lysimeter KW - Microplastics KW - Heavy Metals KW - PAH KW - TED-GC/MS PY - 2024 AN - OPUS4-61160 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hoque, Maroof Arshadul T1 - Mechanochemically synthesized COF for PFAS adsorption N2 - Since the 1950s, per- and polyfluoroalkyl substances (PFAS) have been widely used in a range of consumer products, including clothing, paints, cookware and fast-food packaging. Properties such as high thermal resistance and water and oil repellency contribute to their wide usage. After decades of production, these substances have eventually found their way into our drinking water. Given the adverse effects of PFAS molecules on human health, the removal of these substances from our drinking water is a matter of urgency.1 This study employs the use of materials known as covalent organic frameworks (COFs) to adsorb PFAS molecules from an aqueous medium. COFs are crystalline, highly porous, two- or three-dimensional polymers with tunable topology and functionalities.² For the purposes of this study, a COF was synthesised using 1,3,5-tris(4-aminophenyl)benzene (TAPB) and 1,3,5-triformylbenzene (TFB) via a mechanochemical process. Mechanochemistry represents a green synthesis method that uses mechanical energy to initiate chemical reactions, as opposed to using harmful solvents and heat.3 Adsorption tests were carried out to test the effectiveness of the material in question against PFAS. The COF was exposed to a solution of perfluorooctanoic acid (PFOA) and perfluorooctanesulfonic acid PFOS). Following a 13-hour period, it was observed that 90% of PFOA and 99% of PFOS had been adsorbed by the COF. Most of the adsorption appeared to have occurred within the first 10 minutes of exposure. It can therefore be concluded that the TAPB-TFB COF is a promising material for the adsorption of PFAS molecules. T2 - Adlershofer Forschungsforum 2024 CY - Berlin, Germany DA - 11.11.2024 KW - Covalent organic framework KW - Mechanochemistry KW - PFAS KW - In situ Xray diffraction PY - 2024 AN - OPUS4-61808 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stawski, Tomasz A1 - Karafiludis, Stephanos A1 - Standl, Jakob A1 - Ryll, Tom A1 - Schwab, Alexander A1 - Prinz, Carsten A1 - Wolf, Jakob A1 - Kruschwitz, Sabine A1 - Emmerling, Franziska A1 - Völker, Christoph T1 - High-Entropy Metal Phosphate Synthesis: Advancements through Automation and Sequential Learning Optimization N2 - To accelerate high-entropy metal phosphate (HEMP) discovery, we employed a Random Forest regression model within a SLAMD framework. Trained on limited initial data, the model efficiently explored the vast compositional space to predict a novel five-metal phosphate, which was then successfully synthesized and validated experimentally. T2 - AI4 Materials Science and Testing 2025 CY - Berlin, Germany DA - 06.11.2025 KW - Metal phosphates KW - High-entropy KW - Sequential learning PY - 2025 AN - OPUS4-64686 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - de Oliveira Guilherme Buzanich, Ana A1 - Radtke, Martin A1 - Yusenko, Kirill A1 - Stawski, Tomasz A1 - Kulow, Anicó A1 - Cakir, Cafer Tufan A1 - Röder, Bettina A1 - Naese, Christoph A1 - Britzke, Ralf A1 - Sintschuk, Michael A1 - Emmerling, Franziska T1 - BAMline - A real-life sample materials research beamline N2 - With increasing demand and environmental concerns, researchers are exploring new materials that can perform as well or better than traditional materials while reducing environmental impact. The BAMline, a real-life sample materials research beamline, provides unique insights into materials’ electronic and chemical structure at different time and length scales. The beamline specializes in x-ray absorption spectroscopy, x-ray fluorescence spectroscopy, and tomography experiments. This enables real-time optimization of material properties and performance for various applications, such as energy transfer, energy storage, catalysis, and corrosion resistance. This paper gives an overview of the analytical methods and sample environments of the BAMline, which cover non-destructive testing experiments in materials science, chemistry, biology, medicine, and cultural heritage. We also present our own synthesis methods, processes, and equipment developed specifically for the BAMline, and we give examples of synthesized materials and their potential applications. Finally, this article discusses the future perspectives of the BAMline and its potential for further advances in sustainable materials research. KW - Extended X-ray absorption fine structure KW - Energy storage KW - Environmental impacts KW - Nondestructive testing techniques KW - X-ray fluorescence spectroscopy KW - Corrosion KW - Near edge X-ray absorption fine structure spectroscopy KW - X-ray absorption spectroscopy PY - 2023 DO - https://doi.org/10.1063/5.0157194 VL - 158 IS - 24 SP - 1 EP - 22 PB - AIP Publishing AN - OPUS4-57824 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mönch, Bettina A1 - Gebert, Antje A1 - Emmerling, Franziska A1 - Becker, Roland A1 - Nehls, Irene T1 - Koenigs-Knorr reaction of fusel alcohols with methyl (1-bromo-2,3,4-tri-O-acetyl-alpha-D-glucopyranosid)uronate leading to the protected alkyl glucuronides-crystal structures and high resolution 1H and 13C NMR data N2 - Crystal structures and high resolution 1H and 13C NMR spectral data for methyl (alkyl 2,3,4-tri-O-acetyl-β-D-glucopyranosid)uronates (alkyl = methyl, ethyl, n-propyl, i-propyl, n-butyl, sec-butyl, i-butyl, n-pentyl, 2-methyl-1-butyl and 3-methyl-1-butyl) are presented. KW - D-Glucuronic acid derivates KW - X-ray analysis KW - High resolution NMR KW - Anomeric configuration KW - Synthesis PY - 2012 DO - https://doi.org/10.1016/j.carres.2012.01.002 SN - 0008-6215 SN - 1873-426X VL - 352 SP - 186 EP - 190 PB - Elsevier CY - Amsterdam AN - OPUS4-25759 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Urs A1 - Schlegel, Moritz-Caspar A1 - Emmerling, Franziska T1 - Advanced techniques for studying damage mechanisms of cementitious matrices affected by sulfate attack N2 - Cementitious materials, in particular concrete, are durable materials if prepared appropriately and the Service life of concrete structures is now often required to last 120 years or more. Concrete durability depends strongly on intrinsic (e.g. composition, porosity) and exterior factors (e.g. moisture condition and composition, frost cycles, load pattem). Deleterious actions leading to concrete degradation are often created by the environment. Extemal sulfate attack is one of the more spectacular damage scenarios for concrete structures caused by the ingress of sulfate ions into the pore System of the material and successive formation of expanding phases. Though in recent years well studied there are still many questions remaining conceming the mechanisms of sulfate attack. In particular over the last ten years, with the increased utilization of blended cements, new questions arose concerning the sulfate resistance of those binder Systems. In the presented study therefore a method was developed to analyze the changes of the phase composition within the micro structure due to sulfate attack. The analytical method was based on pX-Ray diffraction (pXRD) using Synchrotron radiation in Debye-Scherrer (transmission) geometry. The spatial resolution of the method is ca. 10 pm and allows the characterization of phase transformations in the wake of damaging processes in more detail compared to other techniques. Furthermore, the experimental setup provides the possibility for analyzing the phase assemblage of a given sample without destroying the micro structure. This is possible because the specimens for phase analysis consists of thick sections, which can be used for further microscopic analysis of the micro structure and micro chemistry (e.g. by SEM-EDX). Samples containing supplementary cementitious materials were measured in comparison and to reconstruct the influence of the degradation process in detail. Additionally, reaction ffonts within the samples were localized by micro x-ray fluorescence analysis (MXRF). T2 - EMABM 2011 - 13th Euroseminar on microscopy applied to building materials CY - Ljubljana, Slovenia DA - 14.06.2011 KW - Sulfate attack KW - Concrete KW - Synchrotron KW - XRD KW - Phase analysis PY - 2011 SN - 978-961-90366-7-9 SP - 1 EP - 9 AN - OPUS4-24878 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wegner, Karl David A1 - Häusler, I. A1 - Knigge, Xenia A1 - Hodoroaba, Vasile-Dan A1 - Emmerling, Franziska A1 - Reiss, P. A1 - Resch-Genger, Ute T1 - One-Pot Heat-Up Synthesis of ZnSe Magic-Sized Clusters Using Thiol Ligands N2 - The synthesis of two new families of ZnSe magic-sized clusters (MSCs) is achieved using the thiol ligand 1-dodecanethiol in a simple one-pot heat-up approach. The sizes of the MSCs are controlled with the thiol ligand concentration and reaction temperature. KW - ZnSe KW - Magic-sized cluster KW - Dodecanethiol KW - Semiconductor nanocrystals KW - One-pot synthesis PY - 2022 DO - https://doi.org/10.1021/acs.inorgchem.2c00041 VL - 61 IS - 19 SP - 7207 EP - 7211 PB - ACS Publications CY - Washington, DC (USA) AN - OPUS4-54880 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Drago, C A1 - Wiesner, Yosri A1 - Braun, U A1 - Giovannozi, A A1 - Fadda, M A1 - Putzu, Mara A1 - Lorenzo, S A1 - Moscoso-Pérez, C A1 - Benismail, N A1 - Palma, C A1 - Almeida, J A1 - Mattarozzi, M A1 - Barbaresi, M A1 - Piergiovanni, M A1 - Masino, M A1 - Bianchi, F A1 - Careri, M A1 - v Bavel, B A1 - Maltseva, A A1 - Sillanpää, M A1 - Pröfrock, D A1 - Wippermann, D A1 - Altmann, Korinna T1 - Harmonisation of sample preparation for microplastic analysis: Recovery rates of tablets containing microplastics as reference material for food and environmental matrix N2 - Microplastic are found ubiquitarians in the environment and food products. Up to now, their impact of risks on health and environment is still controversially discussed, but based on the precautionary principle alone, their presence should be monitored and emission should be reduced (see here also the status of existing EU regulations ). The crucial point is not only the reduction of microplastics pollution but also the introduction of legally binding, standardized procedures for their analysis. The limited availability of certified reference material as well as absence of standard operating procedures to identify, characterize and quantify microplastics according to number and mass have generated lack of comparability between different analytical methods and laboratories; but also, the need of time-consuming development of own protocols for each laboratory. Further on, harmonisation and standardisation of microplastics analysis requires specific reference materials that are used to validate the measurement and to ensure the comparability of results. In the first step, we developed tablets of a water-soluble matrix, containing defined numbers of microplastic particles or mass contents. These can be solved in water and can be handled as reference materials in bottled drinking water without additional sample preparation. These samples can be measured, using mass-based methods as thermo-analytical methods like thermal desorption-gas chromatography-mass spectrometry (TED-GC/MS) or pyrolysis–gas chromatography–mass spectrometry (Py-GC/MS) and using umber-based methods as vibrational spectroscopy like Infrared and Raman directly after filtration. The aim of this work was to delevop standard operating procedure to measure microplastics in more complex matrices and to harmonise and compare different detection and characterization methods. In fact, these matrices require different additional treatments to allow a reliable quantification and identification of microplastics. T2 - SETAC Europe 2025 CY - Vienna, Austria DA - 11.05.2025 KW - Microplastics KW - Nanoplastics PY - 2025 AN - OPUS4-63366 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Misra, Archismita T1 - Polyoxometalate Ionic Liquids as Protective Coatings for Industrial Infrastructure and Cultural Heritage against Microbiologically Influenced Corrosion (MIC) N2 - Corrosion of stone and metal due to acid rain and biodeterioration poses significant challenges for industrial and residential infrastructure, as well as cultural heritage, including statues and historical artefacts. A promising mitigation strategy involves thin, transparent films of polyoxometalate-based ionic liquids (POM-ILs) as chemical shields. Stone samples coated with acid-resistant, biocidal POM-ILs exhibited negligible corrosion when exposed to simulated acid rain, in stark contrast to the severe deterioration of unprotected samples. Additionally, their biocidal properties effectively prevent biofilm formation on coated surfaces. Following studies successfully explored the effectiveness of the coating against lampenflora growing in the Pommery Champagne cellar; and the long-term performance of POM-ILs under outdoor environmental conditions. So, POM-ILs have already demonstrated remarkable anticorrosion and antimicrobial properties against aerobic microorganisms and, being water-insoluble, do not leach into aquatic ecosystem. The current research project repurposes the POM-ILs, extending their application to metals, specifically targeting microbiologically influenced corrosion (MIC) in cultural heritage artefacts made of brass, carbon steel, cast iron, and bronze. This involves optimizing nanocoating adhesion to the metal surface and evaluating its protective efficacy against MIC caused by anaerobic microorganisms such as methanogenic archaea and sulfate reducing bacteria (SRB). This presentation will highlight POM-ILs as sustainable, high-performance nanocoatings for biocorrosion mitigation. It will showcase published success stories, discuss ongoing research and proof-of-concept results, and explore future prospects for these advanced materials in safeguarding metal infrastructure and artefacts across different industrial sectors as well as in the context of cultural heritage conservation. T2 - Euro-MIC COST Action - Closing Workshop Conference CY - Horsens, Denmark DA - 17.09.2025 KW - Polyoxometalates KW - Corrosion KW - Microbiologically Influenced Corrosion KW - Ionic Liquid PY - 2025 AN - OPUS4-64549 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Abad Andrade, Carlos Enrique T1 - Advances and Applications of Molecular Absorption Spectrometry: from Non-Metals to Isotope Analysis N2 - The present work covers two main aspects of high-resolution continuum source graphite furnace molecular absorption spectrometry (HR-CS-GFMAS), an analytical technique for elemental trace analysis. First, a comprehensive mechanistic study of molecule formation in graphite furnaces is presented, which is a key step into the recovery of analytical signals. For this, the molecule formation of CaF was studied, which is used for the indirect analytical determination of fluorine in HR-CS-GFMAS. A zirconium coating catalyzes the CaF formation, and its structure was investigated. The kinetics of this reaction was established by monitoring its molecular spectrum at different atomisation temperatures. An Arrhenius plot showed a pseudo-first order reaction with respect to fluorine (n = 1). An intermediate state was isolated, and its structure was elucidated by spectroscopic methods: scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDX), X-ray photoelectron spectroscopy (XPS), X-ray absorption spectroscopy (XANES and EXAFS), and Raman microspectroscopy. Here a mechanism is proposed, where ZrO2 works as a heterogeneous catalyst: after a pyrolytic step, an intermediate state of ZrO(OCaF) is activated, and at higher temperatures, CaF(g) is released from the zirconium-coated graphite surface. Second, analytical methods were developed by using HR-CS-MAS as detector for non-metals and isotope analysis. Therefore, the determination of organic absorbable chlorine in water, the quantification of fluorine in consume care products with declared perfluorinated ingredients, and the determination of sulfur content in crude oils were investigated. Finally, the high resolution of the instrumentation allows to measure isotopic shifts with high precision in some observed molecular spectra. Consequently, the molecular spectra of enriched isotopes of boron and magnesium were investigated, establishing so the potential of HR-CS-MAS for the accurate and precise determination of isotopic amount ratios. Zusammenfassung Die vorliegende Arbeit befasst sich mit zwei zentralen Aspekten der High-Resolution-Continuum-Source-Molekülabsorptionsspektrometrie mit Graphitrohrtechnik (HR-CS-GFMAS), einer Analysetechnik für elementare Spurenanalyse. Der erste Teil der Arbeit umfasst eine mechanistische Studie zur Molekülbildung auf Graphitoberflächen. Dies ist ein wichtiger Schritt, um analytische Signale zu entdecken. Dazu wurde die Molekülbildung von CaF analysiert, welches für die indirekte, analytische Bestimmung von Fluor in HR-CS-GFMAS genutzt wird. Die CaF Bildung wurde mittels einer Beschichtung aus Zirconium katalysiert und deren Struktur analysiert. Die Kinetik dieser Reaktion wurde durch Beobachtung des jeweiligen Molekülspektrums bei verschiedenen Atomisierungstemperaturen beobachtet. Ein Arrheniusplot zeigte für Fluor (n = 1) eine Reaktion Pseudo-erster Ordnung. Ein Übergangszustand wurde über die mit Zirconium überzogene Grafitoberfläche isoliert und seine Struktur mittels spektroskopischer Methoden Energiedispersive Rasterelektronenmikroskopie / Röntgenspektroskopie (REM-EDX), Röntgenphoto¬elektronenspektroskopie (XPS), Röntgenabsorptionsspektroskopie (XAS) und Raman Spektroskopie untersucht. Auf Grundlage dieser Ergebnisse wird ein Mechanismus vorgeschlagen, bei dem ZrO2 als heterogener Katalysator fungiert; in Folge einer Pyrolysestufe wird ein Übergangszustand des ZrO(OCaF) aktiviert, welcher bei höheren Temperaturen CaF(g) an der Zirconium-Graphitoberfläche freisetzt. Im zweiten Teil der Arbeit werden Analysemethoden entwickelt, in dem HR-CS-MAS als Detektor für Nichtmetalle und Isotopanalyse angewandt wird. Hierfür wurde organisch gebundenes Chlor im Wasser bestimmt, der Fluorgehalt in Pflegeprodukten mit perfluorierten Inhaltsstoffen quantifiziert und der Schwefelgehalt in Erdöl untersucht. Weiterhin ermöglicht die hohe Auflösung der Messgeräte eine präzise Bestimmung der Isotopenverschiebung einiger untersuchter Molekülspektren. Daher wurden die Molekülspektren angereicherter Bor- und Magnesiumisotope untersucht. Auf diese Weise wurde das Potential von HR-CS-MAS für die akkurate und präzise Bestimmung von Isotop-Mengenverhältnissen nachgewiesen. KW - Isotope analysis KW - Non-metals analysis KW - Molecular absorption spectrometry KW - Boron KW - Fluorine KW - Graphite furnace KW - HR-CS-MAS KW - Applied optical spectroscopy PY - 2019 UR - https://hu-berlin.hosted.exlibrisgroup.com/permalink/f/jl2ii5/HUB_UB_ALMA_DS21669801300002882 SP - X EP - 118 CY - Berlin, Germany AN - OPUS4-49891 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Adhami, Forogh A1 - Safavi, Maliheh A1 - Ehsani, Maryam A1 - Ardestani, Sussan K. A1 - Emmerling, Franziska A1 - Simyari, Farzaneh T1 - Synthesis, crystal structure, and cytotoxic activity of novel cyclic systems in [1,2,4]thiadiazolo[2,3-a]pyridine benzamide derivatives and their copper(ii) complexes N2 - Three N-(pyridine-2-ylcarbamothioyl)benzamide derivatives were synthesized by the reaction of potassium thiocyanate, benzoyl chloride, and 2-amino pyridine derivatives in one pot. The obtained derivatives were oxidized using copper(II) chloride. During the oxidation, two hydrogen atoms were removed, cyclization of the derivatives occurred, and finally, three new N-(2H-[1,2,4]thiadiazolo[2,3-a]pyridine-2-ylidene)benzamide derivatives were produced. Coordination of these three new derivative ligands to the copper(II) ion resulted in the formation of three new complexes: dichlorobis(N-(2H-[1,2,4]thiadiazolo[2,3-a]pyridine-2-ylidene)benzamide)copper(II), dichlorobis(N-(7-methyl-2H-[1,2,4]thiadiazolo[2,3-a]pyridine-2ylidene)benzamide)copper(II), and dichlorobis(N-(5-methyl-2H-[1,2,4]thiadiazolo[2,3-a]pyridine-2-ylidene)benzamide)copper(II). All the synthesized products were characterized by IR, 1H NMR, and 13C NMR spectroscopies. Crystal structures of the obtained N-(pyridine-2-ylcarbamothioyl)benzamide derivatives, N-(2H-[1,2,4]thiadiazolo[2,3-a]pyridine-2-ylidene)benzamide derivatives, and complexes were determined using X-ray single-crystal diffraction; the positions of atoms, bond lengths, bond angles, and dihedral angles were also determined. In all complexes, the coordination of two large monodentate ligands and two chloride anions to the copper(II) ion resulted in the formation of a stable planar geometry around the central ion. Three N-(pyridine-2-ylcarbamothioyl)benzamide derivatives, three N-(2H-[1,2,4]thiadiazolo[2,3-a]pyridine-2-ylidene)benzamide derivatives, and three complexes were evaluated for their cytotoxicity against five human cancer cell lines (breast cancer cell line MDA-MB-231, neuroblastoma cell line SK-N-MC, prostate adenocarcinoma cell line LNCap, nasopharyngeal epidermoid carcinoma cell line KB, and liver cancer cell line HEPG-2) using an in vitro analysis. The N-(pyridine-2-ylcarbamothioyl)benzamide derivatives showed no cytotoxic activity, whereas the N-(2H-[1,2,4]thiadiazolo[2,3-a]pyridine-2-ylidene)benzamide derivatives and their complexes showed significant cytotoxicity, especially against MDA-MB-231 and LNCap cell lines. The complexes demonstrated smaller IC50 values than N-(2H-[1,2,4]thiadiazolo[2,3-a]pyridine-2-ylidene)benzamide derivatives. KW - Copper complexes PY - 2014 DO - https://doi.org/10.1039/c3dt52905c SN - 1477-9226 VL - 43 IS - 21 SP - 7945 EP - 7957 PB - Royal Society of Chemistry (RSC) AN - OPUS4-65449 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schenk, Jonas A1 - Batzdorf, Lisa A1 - Emmerling, Franziska A1 - Kneipp, Janina A1 - Panne, Ulrich A1 - Buurman, Merwe T1 - Simultaneous UV/Vis spectroscopy and surface enhanced raman scattering of nanoparticle formation and aggregation in levitated droplets N2 - The formation and growth of hydroxylamine reduced silver nanoparticles were investigated by simultaneous Raman and UV/Vis spectroscopy coupled to an acoustic levitator as a sample holder. Based on the UV/Vis spectra, a two step particle formation mechanism with fast initial formation and adjacent coalescence can be proposed for the reduction of silver nitrate with hydroxylamine. The presence of the analyte adenine during particle formation resulted in differences in the adenine SERS signature compared to experiments, where adenine was added after particle synthesis. It was possible to monitor the adenine and sodium chloride induced aggregation of the nanoparticles and its dynamics based on both the extinction spectra and the SERS data. Correlating the information from the extinction spectra with the SERS intensity, the maximum SERS signals were observed at maximum extinction of the aggregated nanoparticle solution at the Raman excitation wavelength. PY - 2012 DO - https://doi.org/10.1039/c2ay05744a SN - 1759-9660 SN - 1759-9679 N1 - Geburtsname von Batzdorf, Lisa: Tröbs, L. - Birth name of Batzdorf, Lisa: Tröbs, L. N1 - Geburtsname von Buurman, Merwe: Albrecht, M. - Birth name of Buurman, Merwe: Albrecht, M. VL - 4 IS - 5 SP - 1252 EP - 1258 PB - RSC Publ. CY - Cambridge AN - OPUS4-25742 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wiesner, Yosri A1 - Altmann, Korinna A1 - Braun, U. T1 - Determination of Microplastic Mass Content by Thermal Extraction Desorption Gas Chromatography– Mass Spectrometry N2 - The scientific and practical challenge of detecting microplastics (MPs) in the environment in a targeted and rapid manner is solved by innovative coupling of thermogravimetric analysis with mass spectrometric methods. Fast identification and quantitative determination of most thermoplastic polymers and elastomers is possible by using thermal extraction Desorption gas chromatography–mass spectrometry (TED-GC–MS). KW - Microplastics KW - Mikroplastik KW - TED-GC/MS KW - Microplastics analytic KW - Mikroplastik Massegehalt PY - 2021 VL - 17 IS - 3 SP - 2 EP - 7 PB - MultiMedia (UK) LLC CY - Cranbury AN - OPUS4-52570 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Batzdorf, Lisa A1 - Fischer, Franziska A1 - Wilke, Manuel A1 - Wenzel, Klaus-Jürgen A1 - Emmerling, Franziska T1 - Direct in situ investigation of milling reactions using combined x-ray diffraction and raman spectroscopy N2 - The combination of two analytical methods including time-resolved in situ X-ray diffraction (XRD) and Raman spectroscopy provides a new opportunity for a detailed analysis of the key mechanisms of milling reactions. To prove the general applicability of our setup, we investigated the mechanochemical synthesis of four archetypical model compounds, ranging from 3D frameworks through layered structures to organic molecular compounds. The reaction mechanism for each model compound could be elucidated. The results clearly show the unique advantage of the combination of XRD and Raman spectroscopy because of the different information content and dynamic range of both individual methods. The specific combination allows to study milling processes comprehensively on the level of the molecular and crystalline structures and thus obtaining reliable data for mechanistic studies. PY - 2015 DO - https://doi.org/10.1002/anie.201409834 SN - 1433-7851 SN - 1521-3773 SN - 0570-0833 VL - 54 IS - 6 SP - 1799 EP - 1802 PB - Wiley-VCH CY - Weinheim AN - OPUS4-34630 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Peplinski, Burkhard A1 - Adam, Christian A1 - Reuther, H. A1 - Vogel, Christian A1 - Adamczyk, Burkart A1 - Menzel, Michael A1 - Emmerling, Franziska A1 - Simon, Franz-Georg T1 - First identification of the tridymite form of AlPO4 in municipal sewage sludge ash N2 - Sewage sludge and sewage sludge ashes (SSA) are produced in huge amounts at municipal waste water treatment plants (WWTP) all around the world and have become an issue for many urbanized areas. To deal with this unceasing mass flow in an ecologically and economically responsible way a comprehensive chemical and structural characterization of all types of SSA is needed. X-ray powder diffraction (XRD) is one of the most promising analytical methods for this task. Although, there has been ample chemical evidence showing that many SSA contain aluminium phosphate as a major component up to now no aluminium phosphate or aluminium-rich mixed phosphate phase has been reported to be identified by XRD in a SSA produced at a mono-incineration facility. The outcome of the present com-bined XRD and Mossbauer spectroscopy investigation provides comprehensive evidence closing this gap for the first time. KW - Aluminium phosphate KW - AlPO4 KW - Tridymite KW - Sewage sludge ash KW - Incinerator KW - Ash PY - 2011 DO - https://doi.org/10.1524/zkpr.2011.0067 SN - 0044-2968 VL - 1 SP - 443 EP - 448 PB - Oldenbourg CY - München AN - OPUS4-24297 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dietzmann, Simon T1 - Between Homogenous and Heterogenous Catalysis: Single-Atom-Catalysts N2 - Catalysis is a very important process in chemistry as it lowers the energy barrier for chemical reactions. This saves energy and/or some reactions are only possible with a catalyst under the desired conditions (temperature and pressure). Catalysts can be roughly categorized depending on the phase they interact with the substrates in homogenous and heterogenous catalysis. T2 - 5. Deutsche Tagung für Forschung mit Synchrotronstrahlung, Neutronen und Ionenstrahlen an Großgeräten (SNI2022) CY - Berlin, Germany DA - 05.09.2022 KW - Single-atom-catalyst KW - Electrochemistry KW - Porous carbons PY - 2022 AN - OPUS4-61989 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stawski, Tomasz T1 - Processing of calcium sulfate in brines N2 - Calcium sulfate hemihydrate (CaSO4·0.5H2O), also known as bassanite or "plaster of Paris", serves as a precursor for the production of gypsum (dihydrate, CaSO4·2H2O), widely used in construction. Currently, ~200 MT of calcium sulfate are consumed annually. Bassanite is obtained from gypsum through a solid-state thermal treatment in kilns at temperature ranging from 150 °C to 200 °C. We introduce a more efficient and sustainable method (T < 100 ºC) that enables the direct, rapid, and reversible conversion of gypsum to bassanite using reusable high salinity aqueous solutions (brines with c[NaCl] > 4 M). These transformations are controlled by the properties of the solution, offering extensive opportunities for precise manipulation of crystal formation and recycling of gypsum waste. T2 - BESSY User Meeting 2024 CY - Berlin, Germany DA - 12.12.2024 KW - Gypsum PY - 2024 AN - OPUS4-62095 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Altmann, Korinna A1 - Heymann, S. A1 - Braun, U. A1 - Bannick, C.-G. A1 - Heller, C. A1 - Fuchs, M. A1 - Scheid, C. A1 - Abusafia, A. A1 - Steinmetz, H. A1 - Ricking, M. A1 - Kerndorff, A. T1 - Untersuchungsverfahren von Mikroplastikgehalten im Wasser für Praxis und Wissenschaft N2 - Zielsetzung des vom Bundesministerium für Bildung und Forschung geförderten Projektes RUSEKU war es, repräsentative Untersuchungsstrategien für die Detektion von Mikroplastik mittels TED GC/MS in wässerigen Medien zu ermitteln. Dabei wurden verschiedene Probenahmekonzepte und – verfahren für unterschiedliche Fallgestaltungen und Fragestellungen untersucht, sowie neue Filtersysteme entwickelt. Bei der Detektion der Partikel lag der Fokus auf der Anwendung und Weiterentwicklung der ThermoExtraktion/Desorption-Gaschromatographie-Massenspektrometrie (TED-GC/MS) zur Bestimmung von Mikroplastikgehalten. Anwendung fanden die Methoden bei der Beprobung von Flaschenwasser, Waschmaschinenabläufen, dem urbanen Abwassersystem der Stadt Kaiserslautern, sowie in Oberflächengewässer. KW - Mikroplastik KW - TED-GC/MS KW - Mikroplastik-Analytik KW - Probennahme PY - 2021 VL - 14. Jahrgang IS - 3 SP - 147 EP - 152 PB - Deutschen Vereinigung für Wasserwirtschaft, Abwasser und Abfall CY - Hennef AN - OPUS4-52260 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Eisentraut, Paul A1 - Altmann, Korinna T1 - Repräsentative Mikroplastik-Detektion in Umweltproben - Weiterentwicklung der TED-GC/MS N2 - Die große Herausforderung in der Detektion von Mikroplastik (MP)‑Partikeln (1-1000 µm) besteht darin, sie neben Millionen von natürlichen Partikeln in Umweltproben nachzuweisen. Zum Aufspüren von Senken, Eintragspfaden und für Monitoring-Kampagnen ist ein schnelles, automatisiertes Verfahren unerlässlich. Ein solches Verfahren wurde an der Bundesanstalt für Materialforschung und -prüfung (BAM) mit der ThermoExtraktion/Desorption-Gaschromatographie-Massenspektrometrie (TED-GC/MS) in den letzten Jahren entwickelt. KW - Mikroplastik KW - TED-GC/MS PY - 2021 UR - https://analyticalscience.wiley.com/do/10.1002/was.0004000195 SN - 0016-3538 SP - 2 EP - 5 PB - Wiley-VCH CY - Weinheim AN - OPUS4-54266 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Fahmy, A. A1 - Saeed, A. A1 - Dawood, U. A1 - Abdelbary, H. A1 - Altmann, Korinna A1 - Schönhals, Andreas T1 - Nano-MnO2/xanthan gum composite films for NO2 gas sensing N2 - Nowadays, sensors based on polymers/nanostructured metal oxide composites have been investigated exten-sively because of their sensitivity to NO2 gas at ambient temperature. In this work, nanocomposite membranes of xanthan gum (XG) with different contents of MnO2 nanoparticles were prepared as a potential NO2 gas sensor operating at room temperature by a simple one-step oxidation-reduction reaction. The structural, morphological, thermal, and electrical properties of the composite membrane were investigated. The FT-IR results confirm the successful preparation of MnO2 through the oxidation of XG by KMnO4 and reveal further the structural changes of the XG/MnO2 nanocomposite upon its exposure to NO2 gas. The capping of the synthesized MnO2 nano-particles by XG, the surface composition of the XG/MnO2 nanocomposite membranes, and the effect of NO2 gas on the surface composition was investigated using the XPS technique. The DC conductivity and dielectric loss of nanocomposites were higher than for neat XG. The conductivities of the nanocomposites XG/MO-4, XG/MO-4/ low NO2, and XG/MO-4/high NO2 composites are half, one, and three orders of magnitude higher than that for pure XG revealing a transition from insulating to conductive properties. The results demonstrated that XG/MnO2 nanocomposite membranes are promising for potential applications in NO2 gas sensing. KW - Gas sensors KW - Membranes KW - Metal oxides KW - Nanocomposites KW - Semiconductors PY - 2022 DO - https://doi.org/10.1016/j.matchemphys.2022.127277 SN - 0254-0584 VL - 296 SP - 1 EP - 14 PB - Elsevier B.V. AN - OPUS4-56769 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - PlasticTrace WP1 – Stakeholder Workshop N2 - The talk summarizes the achievments of WP1 of the PlasticTrace project. Microplastic reference materials were developed by producing tablets. Different preparation methods were compared. Characterisation of the tablets was done after filtration with µFTIR, QCL, µRaman, Py-GC/MS and TED-GC/MS after ISO standards ISO 16094-2 and ISO/FDIS 16094-3. Polymer types are polypropylene and polyethylene terephthalate. T2 - Stakeholder Workshop PlasticsTrace CY - Online meeting DA - 09.09.2025 KW - Microplastics KW - Reference materials KW - TED-GC/MS KW - PET PY - 2025 AN - OPUS4-64258 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Meurer, Maren T1 - Accelerated solvent extraction to identify an accurate polyethylene mass value in microplastic analytics N2 - It is of high priority to capture the extent of microplastics (MP) contamination for understanding its impact and consequences to our environment. However, due to a lack of standardized methods, MP analysis as well as its quality assurance, is still a challenge. The thermal extraction desorption-gas chromatography/-mass spectrometry (TED-GC/MS) as a novel innovative thermoanalytic method can detect MP particles in environmental samples based on their decomposition products. According to MP analysis, a distinctively larger polyethylene (PE) content in comparison to other synthetic polymers was detected in environmental samples. Various substances within the matrix which have a similar molecular structure to PE, like fats and oils, might interfere with its marker and lead to an overestimation. In this investigation an automated extraction method, the accelerated solvent extraction (ASE), is introduced as quality control tool before TED-GC/MS measurement. Thereby, not the extract like usually used, but the solid filtrate is analyzed. The aim is to clean the environmental samples from solvent removable compounds which could lead to false positive signals and thus receive a more accurate PE mass. Consequently, a sample mimicking environmental samples with a defined matrix and a known polymer mass was generated. The common polymers polyethylene, polypropylene, polystyrene and styrene-butadiene rubber, used as an indication for tire wear, were added to the matrix. Different parameters for ASE extraction were varied such as different solvents, filters and purge time. Finally, a PE recovery rate of 91 % after extraction could be reached. T2 - Micro 2022 CY - Online meeting DA - 14.11.2022 KW - PE KW - ASE KW - TED-GC/MS PY - 2022 AN - OPUS4-56347 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Prinz, Carsten T1 - Importance of stability studies on porous certified reference materials N2 - In the development of certified reference materials (CRM), it is necessary to examine appropriate materials in advance for homogeneity and stability to meet the criteria of a CRM. In this case, the materials properties are characterized at the actual time without being possible to give a prognosis for suitability in the following years. It is, therefore, necessary to follow the certified material parameters via a monitoring system over the years on sale. For the current development of CRMs, the gained experience from long-term stability studies about the first generation of porous CRMs is significant. This experience is useful to better assess the suitability of candidate materials and thus develop higher quality CRMs in the future. A comparison between the gas sorption CRM materials silica, activated carbons, alpha alumina and anatase titanium oxides will illustrate the importance of long-term stability studies on porous CRMs. T2 - BERM 2018 - 15th International Symposium on Biological and Environmental Reference Materials CY - Berlin, Germany DA - 23.09.2018 KW - Reference material KW - Monitoring KW - Long-term stability PY - 2018 AN - OPUS4-46257 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rautenberg, Max T1 - Metal phosphonates as proton conductors and ORR catalysts N2 - Metal phosphonates are promising materials for applications in fuel cells, due to their high proton conductivity and higher chemical and thermal stability compared to the industry standard (e.g. Nafion®). Additionally, metal phosphonates are precursors to porous carbon materials with evenly distributed centers for ORR catalysis. As a fast and sustainable synthesis, mechanochemistry is the synthesis method of choice. Thorough characterization is carried out by XRD, MAS-NMR, XAS, BET, and DVS. T2 - 2nd European Workshop on Metal Phosphonates CY - Berlin, Germany DA - 24.09.2019 KW - Phosphonates KW - Proton cunductor KW - Oxygen reduction reaction KW - Catalysis KW - Mechanochemistry PY - 2019 AN - OPUS4-50257 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Sobina, E. A1 - Zimathis, Anett A1 - Prinz, Carsten A1 - Emmerling, Franziska A1 - de Santis Neves, R. A1 - Galhardo, C. E. A1 - De Robertis, E. A1 - WANG, H. A1 - Mizuno, K. A1 - Kurokawa, A. A1 - Unger, Wolfgang T1 - Final report of CCQM-K136 measurement of porosity properties (specific adsorption, BET specific surface area, specific pore volume and pore diameter) of nanoporous Al2O3 N2 - The CCQM-K136 key comparison for determination of the porosity properties of aluminum oxide has been organized jointly by the surface and micro/nano analysis working groups of CCQM to test the abilities of the metrology institutes to measure the porosity properties (specific adsorption, BET specific surface area, specific pore volume and pore diameter) of nanoporous Al2O3. Ural Scientific Research Institute for Metrology (UNIIM) acted as the coordinating laboratory for this comparison with BAM Federal Institute for Materials Research and Testing (BAM) as co-coordinating laboratory. Five NMIs and one DI participated in this key comparison. All participants used a gas adsorption method, here nitrogen adsorption at 77.3 K, for analysis according to the international standards ISO 15901-2 and 9277. KW - BET specific surface area KW - Specific adsorption KW - Pore diameter KW - Specific pore volume KW - Nanoporous Al2O3 PY - 2016 UR - http://iopscience.iop.org/article/10.1088/0026-1394/53/1A/08014 DO - https://doi.org/10.1088/0026-1394/53/1A/08014 SN - 0026-1394 SN - 1681-7575 VL - 2016 IS - 53 Technical Supplement SP - Article 08014, 1 EP - 39 PB - IOPscience AN - OPUS4-38282 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kraffert, K. A1 - Kabelitz, Anke A1 - Siemensmeyer, K. A1 - Schmack, R. A1 - Bernsmeier, D. A1 - Emmerling, Franziska A1 - Kraehnert, R. T1 - Nanocasting of superparamagnetic iron oxide films with ordered mesoporosity N2 - Maghemite and magnetite show superparamagnetic behavior when synthesized in a nanostructured form. The material’s inducible magnetization enables applications ranging from contrast enhancing agents for magnetic resonance imaging to drug delivery systems, magnetic hyperthermia, and separation. Superparamagnetic iron oxides with templated porosity have been synthesized so far only in the form of hard-templated powders, where silicon retained from the template severely degrades the material’s magnetic properties. Here, for the first time, the synthesis of superparamagnetic iron oxides with soft-templated mesopore structure is reported. The synthesis of nanostructured maghemite and magnetite films succeeds using micelles of amphiphilic block-copolymers as templates. A thermal treatment of the initially formed mesoporous ferrihydrite in nitrogen produces maghemite, which can be partly reduced to magnetite via thermal treatment in hydrogen while retaining the templated mesopore structure. The resulting materials feature a unique combination of high surface area, controlled pore diameter, and tunable magnetic properties. KW - Iron oxide films KW - Mesoporosity KW - Soft-templated PY - 2018 DO - https://doi.org/10.1002/admi.201700960 SN - 2196-7350 VL - 5 IS - 3 SP - 1700960, 1 EP - 1700960, 7 PB - Wiley-VCH CY - Weinheim AN - OPUS4-43560 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Miclea, P-T T1 - Evaluation of Toxicological Characteristics of Airborne Nano/Microplastic Particles From the Industrial Environment N2 - Micro and nano plastic (MNPs) particles and fibres represent a global scale contamination source with hazard potential. They can be identified all around our environment, even in air, soil and water. One of the major global MNPs polluters is the textile industry, which generates plastic particles (nylon, polyester, polyurethane, polyolefin, acrylic etc.) during the manufacturing processes. The study analyses the level of particle concentration outside a company that processes textile yarns, but also from the proximity of workplaces using an online air samplers with cascade and mono filter holders for silicon (Si) and quartz filters, respectively. A laser detector was used for real- time counting of particles of six size classes (PM0.3-PM10). Silicon (Si) filters with a diameter of 9 mm and pore sizes of 10 µm and 1 µm and quartz filters with a diameter of 25 mm and a pore size of 1.2 µm were used for particle sampling. A special holder was designed and made for selective sampling (PM10 and PM1.0) on Si filters. Quartz filters were pre-calcined (8000C) before collection. Sampling parameters: airflow (GilAir Plus pump) -2 l/m3, collection time -3 hours; starting time 7.00 am (T1)/2.00 pm (T2), intermittent natural ventilation, average temperature and humidity: 23.3 0C, RH: 52.5%. The weight of particles collected (µg) on the quart filters was 4.9E-05 (T1) and 5.1E-05 (T2) and on the Si filters 3,2 E-05(T1) and 5E-06(T2). The total number of the outside particles (PM0,3-PM10) was situated between 3584,58 (T1)-15165,05(T2) and inside 9901(T1) and 12921,61(T2). The highest number of PM 10 particles inside was 72/m3 and of PM0.3 particles 71979/m3. The samples were characterized using electron microscopy and µRaman spectroscopy. All samples showed a high concentration of particles on the filter. Samples show only particles with irregular shapes. The equivalent particle diameter was for PM10: 1-5 µm and PM1<1 µm. The total Ion Chromatogram shows the presence of PET-type polymer and the TED GS-MS analysis shows that the weight of the collected particles is PET. After extracting the particles from the quartz filters, they were tested for evaluation of the cytotoxic potential of preparations on human monocyte-macrophage cell cultures and peripheral lymphocytes. In the first case, the level of cytotoxicity was at the border between non-cytotoxic and cytotoxic and in the second test the result was moderate cytotoxic. T2 - SETAC Europe 2025 CY - Vienna, Austria DA - 11.05.2025 KW - Microplastics KW - TED-GC/MS KW - Nanoplastics KW - Raman microscopy PY - 2025 AN - OPUS4-63378 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pauw, Brian Richard T1 - NeXus at the core of the HExX-lab N2 - Through bottom-up, comprehensive digitalisation of all aspects of an experiment, the HEX-lab improves the trustworthiness (traceability, reproducibility, quality) of scientific findings. The five main parts that make up a materials science experiment, i.e. Sample preparation, Measurements, Processing, Analysis, and Interpretation, each have been addressed in thorough and unique ways in this lab, building up a foundation for a wide range of materials science collaborations. Improvements span the spectrum. Hardware developments include new sample environments and stages, such as grazing incidence motion towers, electrochemistry cells and flow-through holders, electronic components such as safety interlocks and multipurpose I/O controllers, and liquid handling systems such as coolant flow cross-over systems. Software developments include: 1) a new comprehensive control system operating on both the RoWaN as well as the MOUSE allowing for full Python control and sequencing of all experimentation, 2) Automated scripts for instrument optimization, sample alignments and measurements, 3) revamped data pipelines and analysis software, standalone or launched as part of operations sequencing dashboards on servers, and 4) meticulously structured archival datafiles, fully documenting sample preparation, measurements, processing and analyses. These allow for holistic databases and dashboards to be constructed to investigate the links between synthesis parameters and resulting morphology. This presentation will highlight some of the tools and techniques developed and available in the HEX-lab over the years, from sample environments to overarching experiment and data organisation structures. T2 - Materials Science Core Facility Synergy Forum 2025 CY - Bremen, Germany DA - 26.02.2025 KW - Digitalization KW - Automation KW - HDF5 KW - Traceability KW - Data stewardship KW - Lab automation KW - Holistic science KW - Methodology PY - 2025 AN - OPUS4-62676 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bresch, Harald T1 - Nano and Advanced Materials - Competences at BAM and perspectives N2 - This presentation gives an overview about the competencies and the characterization possibilities of nanoparticles at BAT, based on this the development of the OECD TG 125 at BAM. It further describes research activities at BAM concerning the characterization of nanoparticles and the way to the digital representation of these characterization possibilities. It concludes with the challenges of a digital product passport (DPP) for nanomaterial based products and the need of a digital materials passport (DMP). Finally, the activities of BAM are presented which address the former mentioned challenges from ESRP and DPP. T2 - Austausch Helmholtz Hereon / Digipass & BAM CY - Berlin, Germany DA - 07.07.2025 KW - Nanomaterials KW - ESPR KW - DPP KW - Nano KW - Advanced Materials PY - 2025 AN - OPUS4-64974 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Nusser, K. A1 - Mosbauer, T. A1 - Schneider, G. J. A1 - Brandt, K. A1 - Weidemann, Gerd A1 - Goebbels, Jürgen A1 - Riesemeier, Heinrich A1 - Göritz, D. T1 - Silica dispersion in styrene butadiene rubber composites studied by synchrotron tomography N2 - By means of synchrotron X-ray computed tomography, model composites consisting of silica and styrene–butadiene rubber were studied with a very high spatial resolution. By our analysis technique we were able to determine the nano- and micro dispersion from the experimental results by our numerical analysis. These results are discussed with respect to crucial advantages of the generically 3-dimensional tomography technique as compared to 2-dimensional methods. Our quantitative analysis of the 3d images demonstrates that in the case of our model composites the filler dispersion is good, independent on the filler concentration. Our new 3-dimensional results evidence that considering only 2-d pictures may lead to ambiguities that can lead to wrong conclusions. KW - X-ray tomography KW - Silica KW - Styrene butadiene rubber KW - Dispersion PY - 2012 DO - https://doi.org/10.1016/j.jnoncrysol.2011.10.009 SN - 0022-3093 VL - 358 IS - 3 SP - 557 EP - 563 PB - North-Holland Publ. Co. CY - Amsterdam AN - OPUS4-26105 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Stawski, Tomasz A1 - Smales, Glen Jacob A1 - Scoppola, E. A1 - Jha, D. A1 - Morales, L. F. G. A1 - Moya, A. A1 - Wirth, R. A1 - Pauw, Brian Richard A1 - Emmerling, Franziska A1 - Van Driessche, A. E. S. T1 - Seeds of imperfection rule the mesocrystalline disorder in natural anhydrite single crystals N2 - In recent years, we have come to appreciate the astounding intricacies associated with the formation of minerals from ions in aqueous solutions. In this context, a number of studies have revealed that the nucleation of calcium sulfate systems occurs nonclassically, involving the aggregation and reorganization of nanosized prenucleation species. In recent work, we have shown that this particle-mediated nucleation pathway is actually imprinted in the resultant micrometer-sized CaSO4 crystals. This property of CaSO4 minerals provides us with the unique opportunity to search for evidence of nonclassical nucleation pathways in geological environments. In particular, we focused on large anhydrite Crystals extracted from the Naica Mine in Mexico. We were able to shed light on this mineral's growth history by mapping defects at different length scales. Based on this, we argue that the nanoscale misalignment of the structural subunits, observed in the initial calcium sulfate crystal seeds, propagates through different length scales both in morphological, as well as in strictly crystallographic aspects, eventually causing the formation of large mesostructured single crystals of anhydrite. Hence, the nonclassical nucleation mechanism introduces a “seed of imperfection,” which leads to a macroscopic “single” crystal whose fragments do not fit together at different length scales in a self-similar manner. Consequently, anisotropic voids of various sizes are formed with very welldefined walls/edges. However, at the same time, the material retains in part its single crystal nature. KW - Calcium sulfate KW - Anhydrite KW - Mesocrystal KW - Nucleation KW - Naica PY - 2021 DO - https://doi.org/10.1073/pnas.2111213118 SN - 0027-8424 VL - 118 IS - 48 SP - 1 EP - 11 PB - National Academy of Sciences (USA) CY - Washington AN - OPUS4-53820 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Juribašić, M. A1 - Halasz, I. A1 - Budimir, A. A1 - Užarević, K. A1 - Lukin, S. A1 - Monas, A. A1 - Emmerling, Franziska A1 - Plavec, J. A1 - Ćurić, M. T1 - Reversible Gas−Solid Ammonia N−H Bond Activation Mediated by an Organopalladium Complex N2 - N−H bond activation of gaseous ammonia is achieved at room temperature in a reversible solvent-free reaction using a solid dicyclopalladated azobenzene complex. Monitoring of the gas−solid reaction in real-time by in situ solid-state Raman spectroscopy enabled a detailed insight into the stepwise activation pathway proceeding to the final amido complex via a stable diammine intermediate. Gas−solid synthesis allowed for isolation and subsequent structural characterization of the intermediate and the final amido product, which presents the first dipalladated complex with the PdII−(μ-NH2)−PdII bridge. Gas−solid reaction is readily followed via color changes associated with conformational switching of the palladated azobenzene backbone. The reaction proceeds analogously in solution and was characterized by UV−vis and NMR spectroscopies showing the same stepwise route to the amido complex. Combining the experimental data with density functional theory calculations we propose a stepwise mechanism of this heterolytic N−H bond activation assisted by exogenous ammonia. KW - In situ KW - Mechanochemistry PY - 2017 DO - https://doi.org/10.1021/acs.inorgchem.7b00422 VL - 56 SP - 5342 EP - 5351 PB - American Chemical Society CY - Washington, DC, USA AN - OPUS4-40464 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wilke, Manuel A1 - Bach, S. A1 - Gorelik, T. A1 - Kolb, U. A1 - Tremel, W. A1 - Emmerling, Franziska T1 - Divalent metal phosphonates – new aspects for syntheses, in situ characterization and structure solution N2 - Divalent metal phosphonates are promising hybrid materials with a broad field of application. The rich coordination chemistry of the phosphonate linkers enables the formation of structures with different dimensionalities ranging from isolated complexes and layered structures to porous frameworks incorporating various functionalities through the choice of the building blocks. In brief, metal phosphonates offer an interesting opportunity for the design of multifunctional materials. Here, we provide a short review on the class of divalent metal phosphonates discussing their syntheses, structures, and applications. We present the advantages of the recently introduced mechanochemical pathway for the Synthesis of divalent phosphonates as a possibility to generate new, in certain cases metastable compounds. The benefits of in situ investigation of synthesis mechanisms as well as the implementation of sophisticated methods for the structure analysis of the resulting compounds are discussed. KW - Metal phosphonate KW - Mechanochemistry PY - 2017 DO - https://doi.org/10.1515/zkri-2016-1971 SN - 2194-4946 SN - 2196-7105 VL - 232 IS - 1-3 SP - 209 EP - 222 PB - De Gruyter AN - OPUS4-40003 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Fahmy, A. A1 - Al-Nasser, K. S. A1 - Ali, I. O. A1 - Salama, T. M. A1 - Altmann, Korinna A1 - Friedrich, J. F. T1 - Tuning of adhesion of silver nanoparticles onto zeolite ZSM-5 using electrospray ionization (ESI) encapsulation with poly(acrylic acid) deposited by electrospray ionization (ESI) N2 - The electrospray ionization (ESI) method was used for deposition of thin films of poly(acrylic acid) (PAA) onto ZSM-5, Cu/ZSM-5 and Ag-Cu/ZSM-5 zeolites. This method allowed the formation of uniform polymer films of controlled thickness on conductive substrates. The zeolites were prepared home-made. The effect of incorporation of Cu (5 wt.%) and Ag-Cu (1+4 wt.%) onto ZSM-5 on its particle size, unit cell parameters and crystallinity was investigated. The deposited PAA layer acts as a common dispersing agent with its ionic COOH (COO-) groups. The antibacterial activity towards the bacterial strains such as Staphylococcus pneumonia (S. Pneumonia), Bacillus subtilis (B. subtilis), Escherichia coli (E. coli) and Pseudomonas aeruginosa (P. aeruginosa) as Gram positive and Gram negative bacteria, respectively, and Aspergillus fumigatus (A. fumigatus), Candida albicans (C. albicans) as Fungi was evaluated. The chemical and physical modifications of ZSM-5, Cu/ZSM-5 and Ag-Cu/ZSM-5 surfaces were characterized by X-ray photoelectron spectroscopy, Fourier-transform infrared spectroscopy, atomic force microscopy and X-ray diffraction. The Cu/ZSM-5 and Ag-Cu/ZSM-5 nanocomposites coated with a 10 nm thick PAA layer exhibit significant antibacterial activity. The carboxyl (¬-COOH) or the corresponding carboxylate groups (¬-COO-) interact with Cu2+ and Ag+ ions by formation of ionic bonds (¬-COO-Ag+ or 2 ¬-COO->Cu2+). Moreover, short exposure to light and temperature has reduced Cu2+ and Ag+ to Cu0 and Ag0. KW - Elektrospray Ionization KW - Silver nanoparticles KW - Adhesion PY - 2017 DO - https://doi.org/10.1080/01694243.2017.1315910 VL - 31 IS - 24 SP - 2641 EP - 2656 PB - Taylor & Francis CY - Adingdon AN - OPUS4-40506 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Joester, Maike A1 - Seifert, Stephan A1 - Emmerling, Franziska A1 - Kneipp, Janina T1 - Physiological influence of silica on germinating pollen as shown by Raman spectroscopy N2 - The process of silicification in plants and the biochemical effects of silica in plant tissues are largely unknown. To study the molecular changes occurring in growing cells that are exposed to higher than normal concentration of silicic acid, Raman spectra of germinating pollen grains of three species (Pinus nigra, Picea omorika, and Camellia japonica) were analyzed in a multivariate classification approach that takes into account the variation of biochemical composition due to species, plant tissue structure, and germination condition. The results of principal component analyses of the Raman spectra indicate differences in the utilization of stored lipids, a changed mobilization of storage carbohydrates in the pollen grain bodies, and altered composition and/or structure of cellulose of the developing pollen tube cell walls. These biochemical changes vary in the different species. KW - Silica KW - Raman spectroscopy KW - Principal component analysis PY - 2017 DO - https://doi.org/10.1002/jbio.201600011 SN - 1864-063X SN - 1864-0648 VL - 10 IS - 4 SP - 542 EP - 552 AN - OPUS4-40090 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Fischer, Franziska A1 - Fendel, Nicole A1 - Greiser, Sebastian A1 - Rademann, Klaus A1 - Emmerling, Franziska T1 - Impact is important - Systematic investigation of the influence of milling balls in mechanochemical reactions N2 - A newly established in situ technique using Raman spectroscopy was employed for the detailed kinetic investigation of mechanochemical reaction pathways. This approach was applied for the systematic investigation of the direct influence of colliding balls on the reaction rate constants of a mechanochemical cocrystallization reaction. As a model reaction, the mechanochemical cocrystallization of felodipine and the coformer imidazole was investigated. Keeping the total ball mass constant by varying the number of milling balls, our study reveals that the impact of each single collision has a more significant influence on the reaction kinetics than expected. KW - Mechanochemistry KW - In situ KW - Cocrystal PY - 2017 UR - http://pubs.acs.org/doi/abs/10.1021/acs.oprd.6b00435 DO - https://doi.org/10.1021/acs.oprd.6b00435 SN - 1083-6160 SN - 1520-586X VL - 21 IS - 4 SP - 655 EP - 659 AN - OPUS4-40355 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Castro, R. A. E. T1 - New cocrystals of bexarotene with pyridinecarboxamide isomers sustained by the acid∙∙∙aromatic nitrogen supramolecular heterosynthon N2 - Pharmaceutical cocrystals are homogenous crystalline structures made up of two or more components in a definite stoichiometric ratio, where at least one of the components in the crystal lattice is an active pharmaceutical ingredient (API).1 Pharmaceutical cocrystals have opened the opportunity for engineering solid-state forms designed to have tailored properties to enhance drug product bioavailability and stability, as well a enhance processability of the solid material inputs in drug product manufacture. In this work the cocrystallization of bexarotene, an approved API by the U.S. Food and Drug Administration that belongs to Biopharmaceutics Classification System Class II (low solubility–high permeability), with pyridine carboxamide isomers (picolinamide, nicotinamide and isonicotinamide) was successfully undertaken. The synthesis was achieved by liquid assisted grinding (LAG) and the solids obtained were characterized by differential scanning calorimetry (DSC), infrared spectroscopy (FTIR-ATR), powder X-ray diffraction (XRPD), single crystal X-ray diffraction (SXD), and polarized light thermomicroscopy (PLTM). For bexarotene: picolinamide and bexarotene:isonicotinamide, 1:1 cocrystals were obtained directly from milling. SXD data of bexarotene:isonicotinamide cocrystal reveal acid∙∙∙aromatic nitrogen supramolecular heterosynthon and that the homosynthon amide∙∙∙amide in isonicotinamide is preserved. The bexarotene:nicotinamide mixtures prepared by ball milling give rise to simple binary solid–liquid phase diagram with an eutectic point, well described by the Schröder-van Laar equation. Melt crystallization of the 1:1 mixture gives rise to a cocrystal for which a complex phase behaviour is observed. T2 - 6th Meeting IAPC CY - Zagreb, Croatia DA - 04.09.2017 KW - Crystalline structure KW - Bexarotene KW - Powder X-ray diffraction KW - Single crystal X-ray diffraction KW - Infrared spectroscopy PY - 2017 AN - OPUS4-41063 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ricking, Matthias T1 - Untersuchungen zur repräsentativen Probennahme von Plastik in Wässern N2 - In den letzten Jahren sind vermehrt Publikationen zum Vorkommen von Kunststoffen – insbesondere Mikroplastik (MP) - in limnischen Gewässern,oder Kläranlagen,zu finden. Die bisherigen Untersuchungen und Befunde sind allerdings hinsichtlich der Anzahl-, Volumen- und Massenkonzentrationen und der Größenverteilung von MP nur eingeschränkt bewertbar. Der Grund hierfür ist das Fehlen einer einheitlichen Methodik zur Probennahme für Wässer, der Probenaufarbeitung und der dann folgenden Analytik der Plastiksorten und Partikelgrößen. T2 - Wasser 2017 CY - Donaueschingen, Germany DA - 22.05.2017 KW - Mikroplastik KW - Probenahme PY - 2017 AN - OPUS4-40439 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Goedecke, Caroline T1 - Optimierte Materialien und Verfahren zur Entfernung von Mikroplastik aus dem Wasserkreislauf N2 - Das Ziel des OEMP-Projektes ist die Entwicklung neuer Materialien, um den Rückhalt von Mikroplastik-Partikeln (MP) aus verschiedenen urbanen Eintragspfaden (Kläranlagenablauf, Mischwasserüberlauf und Straßenabfluss) zu optimieren. Grundlage für die Bewertung ist die Entwicklung von geeigneten Untersuchungsverfahren (Probennahme, Probenaufbereitung, Detektion) zur Qualifizierung und Quantifizierung von MP in den relevanten Umweltmatrices. Diese Verfahren müssen zeiteffizient und zuverlässig sein. T2 - Statusseminar der BMBF-Fördermaßnahme „MachWas – Materialien für eine nachhaltige Wasserwirtschaft“ CY - Frankfurt am Main, Germany DA - 25.04.2017 KW - Mikroplastik KW - TED-GC-MS KW - Umweltproben PY - 2017 AN - OPUS4-40263 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nützmann, Kathrin T1 - Depth dependent phase identification of corrosion zones in ferritic alloys by micro-X-ray absorption near edge structure spectroscopy N2 - Ferritic steels with chromium contents up to 13 wt% are used as materials for power plant components as boiler materials (< 2 wt% Cr) and super heater tubes (> 9 wt% Cr). These materials are subject to aggressive corrosion caused by hot gases such as CO2, H2O, O2 and SO2. Especially SO2 causes fatal corrosion even as a minor component. To examine sulfurous corrosion mechanisms, experiments with pure SO2 were conducted. A proper analysis of the material changes requires phase identification and quantification with a high lateral resolution within the corrosion scale. T2 - ANAKON2017 CY - Tübingen, Germany DA - 03.04.2017 KW - Corosion KW - Steel KW - XANES PY - 2017 AN - OPUS4-40415 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Herzel, Hannes T1 - Phase reaction during thermochemical treatment of sewage sludge and biomass ashes with alkali compounds to increase nutrient plant availability N2 - Das Element Phosphor ist für Pflanzen, Tiere und Menschen essenziell. Um die Phosphorversorgung für Pflanzen in der Landwirtschaft zu gewährleisten, werden Phosphordünger eingesetzt. Die Nährstoffe werden hauptsächlich durch Wirtschaftsdünger (Gülle, Jauche, Stallmist) zurückgeführt. Zusätzlich werden in der konventionellen Landwirtschaft mineralische Phosphordünger eingesetzt, die vorwiegend aus dem fossilen Rohstoff Phosphorit gewonnen werden. Um die Abhängigkeit von fossilen Rohstoffen zu reduzieren, sollen nährstoffhaltige Rest- und Abfallstoffe zur Phosphordünger aufbereitet werden. In Abwasserkläranlagen fällt phosphorreicher Klärschlamm als Abfallstoff an. Der größte Anteil des Klärschlammes wird in Steinkohlekraftwerken, Zementwerken oder in Monoklärschlammverbrennungsanlagen verbrannt. Die Klärschlammaschen aus den Monoverbrennungsanlagen enthalten bis zu 12 Gew.-% Phosphor und sind daher für die Düngerherstellung geeignet. Ein geeignetes Verfahren zur Aufbereitung der Klärschlammaschen ist die thermochemische Behandlung im Drehrohrofen. Mit dem sogenannten AshDec®-Prozess, kann ein Phosphordünger hergestellt werden. Aktuell wird eine großtechnische Anlage in Altenstadt (Bayern) geplant, die im Jahr 2023 den Betrieb aufnehmen soll. Der zentrale Bestandteil ist die Phasenumwandlung von schlecht pflanzenverfügbaren Phosphaten in der Klärschlammasche (vorwiegend das Calciumphosphat Whitlockit und Aluminiumphosphat) zu gut pflanzenverfügbaren Calciumalkaliphosphaten im Produkt. Um dies zu erzielen, werden die Aschen mit Natrium- und/oder Kalium-Verbindungen gemischt und einer thermochemischen Behandlung bei 800-1000 °C zugeführt. Um die Pflanzenverfügbarkeit und Düngewirkung von Phosphaten abschätzen zu können, ist die chemische Extraktionsmethode mit neutraler Ammoniumcitratlösung geeignet. In der Dissertation werden die (Phosphor-)Phasenreaktionen und die Prozessbedingungen des thermochemischen Verfahrens untersucht, um das Verfahren gezielt zu modifizieren und die Wirtschaftlichkeit zu steigern. Die Zielphasen der thermochemischen Behandlung sind die Calciumalkaliphosphate CaNaPO4 und CaKPO4, und deren Mischphasen Ca(Na,K)PO4, welche in der Publikation 3.1 synthetisiert wurden. Für diese Calciumalkaliphosphate wurden die thermodynamischen Daten der Standardbildungsenthalpie, Standardentropie, Wärmekapazität und die Wärmemenge der Phasenumwandlung bestimmt (Publikation 3.1). Bei der thermochemischen Behandlung von Klärschlammaschen wurden als Additive Natrium- und Kaliumsulfat bei verschiedenen Temperaturen getestet. Der Einsatz von Kaliumadditiven ist erwünscht, um den Marktwert des Produktes durch die Produktion eines Phosphor-Kalium-Düngers zu erhöhen. Zusätzlich wird eine möglichst geringe Prozesstemperatur angestrebt, bei der die erwünschten Calciumalkaliphosphate gebildet werden. In den Publikationen 3.2 und 3.3 wird gezeigt, dass für Klärschlammaschen eine komplette Phasenumwandlung zu Calciumnatriumphosphaten ab 875 °C in Laborversuchen (Korundtiegel) mit dem Additiv Natriumsulfat erzielt werden kann. Der Einsatz von Kaliumsulfat erforderte notwendige Reaktionstemperaturen von über 1100 °C. Diese unterschiedlichen Reaktionstemperaturen hängen mit den Schmelzpunkten von Natriumsulfat (890 °C) und Kaliumsulfat (1070 °C) zusammen. Um Kaliumsulfat in den Prozess bei niedrigen Temperaturen zu integrieren, wurden Natriumsulfat und Kaliumsulfat vor der Behandlung gemischt. Dies führte zu einer Schmelzpunkterniedrigung und resultierte in Reaktionstemperaturen zwischen 900 °C bis 1000 °C für die untersuchten Mischungen von Natrium- und Kaliumsulfat (Publikation 3.3). Die Zusammensetzung der Calciumalkaliphosphate Ca(Na,K)PO4 war anders als erwartet. Bei der Phasenanalytik stellte sich heraus, dass bei geringem und mittlerem Anteil von Kaliumsulfat im Alkali-Additiv nur Calciumnatriumphosphate mit sehr geringen Kaliumgehalten gebildet wurden. Erst bei einem hohen Anteil von Kaliumsulfat in der Mischung der Alkalisulfate konnten kaliumhaltige Calciumalkaliphosphate nachgewiesen werden (u.a. (Ca0.9Mg0.1)(Na0.6K0.4)PO4). Dieser geringere Einbau von Kalium in die Calciumalkaliphosphate hängt mit den zusätzlich stattfindenden Reaktionen zwischen den Alkalien und den Silikaten zusammen. Es ist bekannt, dass die zugegebenen Alkalisulfate zuerst mit Silikaten und anschließend mit den Phosphaten reagieren. Silikate bauen bevorzugt Kalium ein, deswegen konnten erst kaliumhaltige Phosphate gebildet werden, wenn die Reaktion mit den Silikaten abgeschlossen war. Dies führte zu einem geringeren Kaliumanteil in den gebildeten Phosphaten im Vergleich zum Kaliumanteil der verwendeten Alkaliadditive. Das in Silikaten gebundene Kalium ist wahrscheinlich schlecht für die Pflanzen verfügbar. Dies könnte den Einsatz der produzierten Phosphor-Kalium-Dünger einschränken. Der bevorzugte Kaliumeinbau in Silikaten konnte auch in Kalkulationen mit den thermodynamischen Daten aus der Publikation 3.1 gezeigt werden. Mittels Phasenanalytik vor und nach der chemischen Extraktion, konnte die Zugehörigkeit zu verschiedenen Modifikationen der Calciumalkaliphosphaten sicher bestimmt werden und eine ungefähre Zusammensetzung dieser Calciumalkaliphosphate abgeschätzt werden. So konnte nachgewiesen werden, dass die Modifikation vom CaNaPO4 ungefähr 10 % Magnesium einbauen kann. Wenn mehr Magnesium eingebaut wird, bildet sich die Phase (Ca,Mg)NaPO4, die eine vergleichbare Struktur wie die bekannte Phase (Ca0.72Mg0.28)NaPO4 aufweist. Dieses magnesiumreiche Calciumnatriumphosphat entstand vermutlich, wenn entweder erhöhte Anteile an Kalium eingebaut wurden (Ca0.8Mg0.2)(Na0.85K0.15)PO4 (Publikation 3.3) oder die Phasenumwandlung vom Calciumphosphat Whitlockit zum Calciumalkaliphosphat CaNaPO4 noch nicht abgeschlossen war (Publikation 3.2). Wenn mehr Kalium eingebaut wird, dann entsteht eine Phase (u.a. (Ca0.9Mg0.1)(Na0.6K0.4)PO4) ähnlich zu den Mischphasen aus der Publikation 3.1. In den Publikationen 3.4 und 3.5 wurden keine Klärschlammaschen untersucht, sondern Biokohlen aus Modellklärschlämmen (Publikation 3.5) und Biomasseaschen (Publikation 3.4) aus der Vergasung oder Verbrennung einer Mischung aus Zuckerrohrbagasse und Hühnertrockenkot. Die thermochemischen Produkte der Biokohlen bzw. Biomasseaschen enthielten das gewünschte CaNaPO4 und hatten eine hohe Düngewirkung in Pflanzenwachstumsversuchen mit Sojapflanzen bzw. Gräsern. KW - AshDec KW - Recycling fertilizer KW - Calcium alkali phosphate PY - 2020 SP - 1 EP - 186 CY - Jena AN - OPUS4-54724 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Altmann, Korinna A1 - Wimmer, Lukas A1 - Alcolea-Rodriguez, Victor A1 - Waniek, Tassilo A1 - Wachtendorf, Volker A1 - Matzdorf, Kay A1 - Ciornii, Dmitri A1 - Fengler, Petra A1 - Milczewski, Frank A1 - Otazo-Aseguinolaza, Itziar A1 - Ferrer, Manuel A1 - Bañares, Miguel A. A1 - Portela, Raquel A1 - Dailey, Lea Ann T1 - Quality-by-design and current good practices for the production of test and reference materials for micro- and nano-plastic research N2 - Understanding the environmental and human health impacts of micro- and nanoplastic pollutants is currently a high priority, stimulating intensive methodological research work in the areas of sampling, sample preparation and detection as well as intensive monitoring and testing. It is challenging to identify and quantify microplastics in complex organic matrices and concepts for nanoplastic detection are still in their infancy. All analytical techniques employed in studying micro- and nanoplastics require suitable reference materials for validation measurements, with requirements as diverse as the analytical tools used, ranging from different polymer types, size distributions and shapes of the material to the concentrations employed in different experimental set ups (ng to g amounts). The aim of this manuscript is to outline current good practices for small-scale laboratory production and characterization of suitable test and reference materials. The focus is placed on top-downfragmentation methods as well as bottom-up precipitation methods. Examples using polyethylene, polypropylene, polystyrene and polyethylene terephthalate with size distribution classes of mainly 10–1000, 1–10 and <1 μm particles will be provided. Experiences and suggestions on how to produce well-characterized micro- and nano-plastics for internal research needs will ensure that studies using the materials have robust and informative outcomes. KW - Mmicroplastics KW - Nanoplastics KW - Reference materials KW - Standard validation method PY - 2025 DO - https://doi.org/10.1016/j.jhazmat.2025.139595 SN - 0304-3894 VL - 497 SP - 1 EP - 20 PB - Elsevier B.V. AN - OPUS4-63958 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Fischer, Franziska A1 - Lubjuhn, Dominik A1 - Greiser, Sebastian A1 - Rademann, K. A1 - Emmerling, Franziska T1 - Supply and demand in the ball mill: competitive cocrystal reactions N2 - The stability of different theophylline cocrystals under milling conditions was investigated by competitive cocrystal reactions. To determine the most stable cocrystal form under milling conditions, the active pharmaceutical ingredient theophylline was either ground with two similar coformers (benzoic acid, benzamide, or isonicotinamide), or the existing theophylline cocrystals were ground together with a competitive coformer. All competitive reactions were investigated by in situ powder X-ray diffraction disclosing the formation pathway of the milling processes. On the basis of these milling reactions, a stability order (least to most stable) was derived: tp/bs < tp/ba < tp/ina < bs/ina. KW - Mechanochemistry KW - Cocrystal KW - Milling PY - 2016 DO - https://doi.org/10.1021/acs.cgd.6b00928 SN - 1528-7483 SN - 1528-7505 VL - 16 IS - 10 SP - 5843 EP - 5851 AN - OPUS4-38097 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Fischer, Franziska A1 - Greiser, Sebastian A1 - Peifer, Dietmar A1 - Jäger, Christian A1 - Rademann, K. A1 - Emmerling, Franziska T1 - Mechanochemically Induced Conversion of Crystalline Benzamide Polymorphs by Seeding N2 - Benzamide has been known for its polymorphism for almost 200 years.Three polymorphic forms are described. To date,itwas only possible to crystallizeametastable form in amixture together with the thermodynamically most stable form I. Acomplete transformation of form Iinto the metastable form III by mechanochemical treatment has been achieved. Catalytic amounts of nicotinamide seeds were used to activate the conversion by mechanochemical seeding. NMR experiments indicated that the nicotinamide molecules were incorporated statistically in the crystal lattice of benzamide form III during the conversion. The transformation pathway was evaluated using in situ powder X-ray diffraction. KW - Nicotinamide KW - Benzamide KW - In situ reactions KW - Mechanochemistry KW - Polymorphs PY - 2016 DO - https://doi.org/10.1002/anie.201607358 VL - 128 IS - 46 SP - 14493 EP - 14497 PB - WILEY-VCH CY - Weinheim AN - OPUS4-38472 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna A1 - Barthel, Anne-Kathrin T1 - The use of reference material in microplastic research: general aspects N2 - Discussions in science, politics and public media about microplastic in the Environment and its unclear effects for animals and humans are common these days. Although microplastic findings in water, soil and even air are well known, no general estimations about the quality or quantity of microplastic particles in environment exit. Research is necessary to develop reliable and traceable, harmonized protocols for sampling, sample preparation and fast, but accurate analysis for qualitative and quantitative measurement of microplastic in various environmental matrices. For development of such reliable and traceable methods, the use of microplastic reference materials is necessary to assess various concepts. These microplastic reference particles should be an appropriate reflection of the microplastic particles found in environment. Due to the high use in industrial products six polymers seem to be relevant in environment as microplastic particles: polyethylene (PE), polypropylene (PP), polystyrene (PS), polyethylene terephthalate (PET), polyamide (PA) and polyvinylchloride (PVC). The raw source of These thermoplastic materials are pellets or granulate with dimensions of 1 to 5 mm in diameter. Most common they own a regular cylindrical shape or are prolate sphericals. These can be bought cost-efficient by various polymer producers. But discussions in microplastic research topic lead to particle sizes down to 1 μm. Furthermore, various unregular shapes and geometries of the particles have to be considered as well as an oxidized surface. In the present work we engage the acquisition and production of realistic reference material. Different aspects should demonstrate the complex and difficult task of generating approriate, cost-efficient and well-defined reference materials. The particle size distribution by using different particle sizing methods as well as individual particle shapes are documented. Different material properties were addressed. PE, PS and PA were chosen as typical and relevant microplastic with opposite individual material characteristics in density and glass Transition temperature. The easiest possibility for acquisition of small microplastic particles is the purchase of polymer emulsion particles (20 to 150 μm). An alternative possibility to produce small microplastic particles is milling under liquid nitrogen conditions in cryo mills. Particles purchased or self-made differ strongly in shape and size depending on production method. SETAC T2 - SETAC CY - Brussels, Belgium DA - 08.05.2017 KW - Microplastics KW - Reference materials KW - Particles PY - 2017 AN - OPUS4-40264 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Emmerling, Franziska T1 - May the Force be with you - Mechanochemical syntheses studied in situ N2 - Mechanochemistry is a fast and efficient method applicable for the synthesis of new organic, metal-organic, and inorganic compounds. The direct monitoring of milling reactions is still challenging. The underlying reaction mechanisms remain often unclear. In the last years, have established a tandem in situ approach for investigating mechanochemical reactions using time-resolved in situ XRD coupled with Raman spectroscopy. Here, we present an in situ coupling of synchrotron XRD, Raman spectroscopy, and thermography allowing the observation of mechanochemical reactions in real time. Information on the crystalline, molecular, and temperature state of the materials during grinding could be collected. The chemical composition of the reaction mixture was found to be directly correlated with changes in the temperature profile of the reaction. Furthermore, the presented setup allows the detection of crystalline, amorphous, eutectic as well as liquid intermediates. The resulting deeper kinetic and thermodynamic understanding of milling processes is the key for future optimization of mechanochemical syntheses. T2 - Seminar Universität Montpellier CY - Montpellier, France DA - 24.01.2019 KW - Mechanochemistry KW - In situ PY - 2019 AN - OPUS4-47261 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wiesner, Yosri T1 - Reference material candidates for Microplastic analysis N2 - Microplastic reference material is required for validation and harmonization purposes. This includes the analysis of the pure polymer particles and the validation of the respective measurement methods. In addition, there is the harmonization of different laboratories. On the other hand, sample preparation methods must be validated and harmonized with regard to their recovery and subsequent analysis in the respective matrices. For this purpose, we produce reference material candidates in the form of tablets with different mass fractions and particle numbers of polyethelene terephthalate. In the presentation first measurement results by µ-Raman, µ-FTIR, pyrolysis-GC-MS and TED-GC/MS will be presented. T2 - SETAC Europe 34th Annual Meeting CY - Seville, Spain DA - 05.05.2024 KW - Reference material KW - Microplastics KW - PlasticTrace PY - 2024 AN - OPUS4-60019 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stawski, Tomasz T1 - Solution-driven processing of calcium sulfate: the mechanism of the reversible transformation of gypsum to bassanite in brines N2 - Calcium sulfate hemihydrate (CaSO4ᐧ0.5H2O), also known as bassanite, has been used as a precursor to produce gypsum (dihydrate, CaSO4ᐧ2H2O) for various construction and decorative purposes since prehistoric times. The main route to obtain hemihydrate is a thermal treatment of gypsum at temperatures typically between 150 °C and 200 °C to remove some of the structural water. In this contribution, we introduce (Fig. 1) a more efficient and sustainable method (T < 100 °C) that enables the direct, rapid, and reversibly conversion of gypsum to bassanite using reusable high salinity aqueous solutions (brines with c[NaCl] > 4 M). The optimum conditions for the efficientproduction of bassanite in a short time (< 5 min) involve the use of brines with c(NaCl) > 4 M and maintaining a temperature, T > 80 °C. When the solution containing bassanite crystals is cooled down to around room temperature, eventually gypsum is formed. When the temperature is raised again to T > 80 °C, bassanite is rapidly re-precipitated. This contrasts with the typical behaviour of the bassanite phase in low salt environments. Traditionally, hemihydrate is obtained through a solid state thermal treatment because bassanite is considered to be metastable with respect to gypsum and anhydrite in aqueous solutions, and therefore gypsum-to-bassanite conversion should not occur in water. Its very occurrence actually contradicts numerical thermodynamic predictions regarding solubility of calcium sulfate phases. By following the evolution of crystalline phases with in situ and time-resolved X-ray diffraction/scattering and Raman spectroscopy, we demonstrated that the phase stability in brines at elevated temperatures is inaccurately represented in the thermodynamic databases. Most notably for c(NaCl) > 4 M, and T > 80 °C gypsum becomes readily more soluble than bassanite, which induces the direct precipitation of the latter from gypsum. The fact that these transformations are controlled by the solution provides extensive opportunities for precise manipulation of crystal formation. Our experiments confirmed that bassanite remained the sole crystalline structure for many hours before reverting into gypsum. This property is extremely advantageous for practical processing and efficient crystal extraction in industrial scenarios. T2 - Granada Münster Discussion Meeting GMDM 10 CY - Münster, Germany DA - 29.11.2023 KW - Gypsum KW - Bassanite KW - Calcium sulfate KW - Recycling KW - Scattering PY - 2024 AN - OPUS4-59162 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Emmerling, Franziska T1 - Synchrotron X-ray Investigations N2 - Summary of the techniques available at the BAMline and µspot BEamline. T2 - Workshop Humboldt University and Hebrew University of Jerusalem CY - Berlin, Germany DA - 09.10.2018 KW - In situ KW - XRD PY - 2018 AN - OPUS4-46993 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - May, Anastasia T1 - Pyrazinamide-Pimelic Acid Cocrystals: A Mechanochemical and Thermal Study N2 - Cocrystals represent a promising class of crystalline materials, offering a wide potential for physico-chemical property alteration of chemical compounds, such as their solubility, by cocrystallizing the targeted compound with another solid material. In the present study, we investigated the cocrystal system between the anti-tuberculosis drug pyrazinamide (PZA) and pimelic acid (PA) by thermal characterization and milling conditions of mechanochemical synthesis. Thermal treatment resulted in the formation of a eutectic between the compounds PZA and PA. Furthermore, irreversible separation of the cocrystal occurred upon melting. This finding indicated low stability of the cocrystal and the necessity of mechanochemical synthesis for cocrystal formation. The mechanochemical synthesis parameters were elucidated by investigating the temperature effect while milling and the role of pre-milling the coformer PA using in-situ monitoring techniques. The polymorphism of PA, influenced by temperature and pre-milling, exhibited a substantial impact on the kinetics of cocrystallization. This finding underscores the significance of coformer polymorphism as an additional factor in mechanochemical cocrystallization reactions. T2 - 11th International Conference on Mechanochemistry and Mechanical Alloying CY - Berlin, Germany DA - 14.09.2025 KW - Cocrystal PY - 2025 AN - OPUS4-65353 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Martins, I. A1 - Carta, M. A1 - Haferkamp, Sebastian A1 - Feiler, Torvid A1 - Delogu, F. A1 - Colacino, E. A1 - Emmerling, Franziska T1 - Mechanochemical N‑Chlorination Reaction of Hydantoin: In Situ Real-Time Kinetic Study by Powder X‑ray Diffraction and Raman Spectroscopy N2 - Mechanochemistry has become a valuable tool for the synthesis of new molecules, especially in the field of organic chemistry. In the present work, we investigate the kinetic profile of the chlorination reaction of N-3-ethyl-5,5-dimethylhydantoin (EDMH) activated and driven by ball milling. The reaction has been carried out using 2 mm, 4 mm, 5 mm, 6 mm, and 8 mm ball sizes in a new small custom-made Perspex milling jar. The Crystal structure of the starting material EDMH and the 1-chloro-3-ethyl5,5′-dimethyl hydantoin (CEDMH) chlorination product was solved by single-crystal X-ray diffraction. The reaction was monitored, in situ and in real time, by both powder X-ray diffraction (PXRD) and Raman spectroscopy. Our kinetic data show that the reaction progress to equilibrium is similar at all milling ball sizes. The induction period is very short (between 10 and 40 s) when using 4 mm, 5 mm, 6 mm, and 8 mm balls. For the reaction performed with a 2 mm ball, a significantly longer induction period of 9 min was observed. This could indicate that an initial energy accumulation and higher mixing efficiency are necessary before the reaction starts. Using different kinetic models, we found that the amount of powder affected by critical loading conditions during individual impacts is significantly dependent on the ball size used. An almost linear correlation between the rate of the chemical transformations and the ball volume is observed. KW - Mechanochemistry KW - In situ real-time monitoring KW - N-Chlorination KW - Kinetics KW - Hydantoin KW - Powder X-ray diffraction KW - Raman spectroscopy PY - 2021 DO - https://doi.org/10.1021/acssuschemeng.1c03812 VL - 9 IS - 37 SP - 12591 EP - 12601 AN - OPUS4-53541 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Souza, B. A1 - Chauque, S. A1 - de Oliveira, P. A1 - Emmerling, Franziska A1 - Torresi, R. T1 - Mechanochemical optimization of ZIF-8/Carbon/S8 composites for lithium-sulfur batteries positive electrodes N2 - The application of lithium-sulfur (Li-S) batteries is still limited by their rapid capacity fading. The pulverization of the sulfur positive electrode after the lithiation and the consequence dissolution of long chain polysulfides in organic solvents lead to the shuttle effect. To address these issues, here we report the mechanochemical preparation of ZIF-8 (Zeolitic Imidazole Framework-8)-based composites as sulfur hosts for positive electrodes in Li-S batteries. We studied different methods for the incorporation of conductive carbon. Also, the replacement of Zn2+ metal centers by other bivalent metals (Cu2+, Co2+ and Ni2+), enabled the preparation of other ZIF-8-based materials. The positive electrode ZIF-8/C/S8 showed initial discharges of 772 mA h g−1 while the pristine one, ZIF-8/S8, displayed 502 mA h g−1. The enhanced performance of 54% for ZIF-8/C/S8 indicates that the direct mechanochemical synthesis of ZIF-8 with conductive carbon is beneficial at initials charge/discharge process in comparison to traditional slurry preparation (ZIF-8/S8). Also, the Li2S6 absorption tests shows 87% of discoloration with ZIF-8/C/S8, confirming the better polysulfides absorption. KW - Lithium-sulfur battery KW - Metal organic frameworks KW - ZIF-8 KW - Mechanochemistry PY - 2021 DO - https://doi.org/10.1016/j.jelechem.2021.115459 VL - 896 SP - 115459 PB - Elsevier B.V. AN - OPUS4-53542 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stawski, Tomasz T1 - Seeds of imperfection rule the mesocrystalline disorder in natural anhydrite single crystals N2 - In recent years, we have come to appreciate the astounding intricacy of the formation process of minerals from ions in aqueous solutions. In this context, a number of studies have revealed that nucleation in the calcium sulfate system is non-classical, involving the aggregation and reorganization of nanosized prenucleation particles. In a recent work we have shown that this particle-mediated nucleation pathway is actually imprinted in the resultant single micron-sized CaSO4 crystals. This property of CaSO4 minerals provides us with an unique opportunity to search for evidence of non-classical nucleation pathways in geological environments. In particular, we focused on the quintessential single crystals of anhydrite extracted from the Naica mine in Mexico. We elucidated the growth history from this mineral sample by mapping growth defects at different length scales. Based on these data we argue that the nano-scale misalignment of the structural sub-units observed in the initial calcium sulfate crystal seed propagate through different length-scales both in morphological, as well as strictly crystallographic aspects, eventually causing the formation of large mesostructured single crystals of anhydrite. Hence, the nanoparticle mediated nucleation mechanism introduces a 'seed of imperfection', which leads to a macroscopic single crystal, in which its fragments do not fit together at different length-scales in a self-similar manner. Consequently, anisotropic voids of various sizes are formed with very well-defined walls/edges. But, at the same time the material retains its essential single crystal nature. These findings shed new light on the longstanding concept of crystal structure. T2 - S4SAS Conference 2021 CY - Online meeting DA - 01.09.2021 KW - SAXS KW - Calcium sulfate KW - Anhydrite KW - Mesocrystals PY - 2021 AN - OPUS4-53630 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rautenberg, Max T1 - Fluorine Modified ZIF 8 for Electrochemical Catalysis: Where does the Fluorine go? N2 - Carbonization of fluorinated metal-organic frameworks (MOFs) should yield fluorinated nitrogen- and metal-doped carbons (F-NMCs), which are a combination of NMCs and fluorinated carbons, each promising electrocatalysts on their own. We synthesized two polymorphs of a fluorinated MOF by mechanical ball mill grinding, and carbonized them to yield potential electrocatalyt materials. The catalytical activity towards the oxygen reduction reaction (ORR) was examined, finding good activites. Simulations from a theoretic model helped assesing the stability of proposed catalytic sites and understanding the measured activites towards the ORR catalysis. T2 - Online symposium of the CRC 1349 "fluorine-specific interactions" CY - Online meeting DA - 29.06.2021 KW - PGM-free catalyst KW - Oxygen Reduction Reaction KW - Mechanochemistry KW - MOFs KW - Computational chemistry PY - 2021 AN - OPUS4-53538 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rautenberg, Max T1 - Synthesis and characterization of fluorinated Co-Zn-Zeolitic imidazole frameworks for catalysis of the oxygen reduction reaction N2 - The oxygen reduction reaction (ORR) is a common process in a variety of electrochemical devices, like fuel cells and metal air batteries. The sluggish kinetics of the ORR require an electrocatalyst to pass this bottleneck.[1] Currently, the most used catalytical systems are platinum-based, with several drawbacks, such as the high cost, low availability, and deactivation by CO poisoning.[2] Efforts are made to develop efficient, durable and low cost catalysts to promote the commercialization of fuel cells. Non-precious metal catalysts are promising candidates for efficient ORR catalysis. It has been shown that pyrolyzing metal organic frameworks (MOFs) under inert conditions yields carbon-rich materials, with evenly distributed metal sites, which possess promising electrocatalytic activity.[3] One widely used type of MOF as ORR catalyst precursors is the zeolitic imidazole framework (ZIF) where metal cations are linked through imidazolebased ligands. Herein we report the mechanochemical synthesis, structural analysis and of Co-doped ZIF-8 (Zn), as well as its fluorinated counterpart Co-doped CF3 -ZIF-8 (Zn). The samples showed electrochemical performance comparable to platinum after carbonization for 1h at temperatures ranging between 850 – 1000°C. T2 - 15th International conference on materials chemistry (MC15) CY - Online meeting DA - 12.07.2021 KW - PGM-free catalyst KW - Oxygen Reduction Reaction KW - Mechanochemistry KW - MOFs PY - 2021 AN - OPUS4-53539 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Karafiludis, Stephanos T1 - Crystallisation of transition metal phosphate as precursors for mesoporous materials N2 - The influence of several precipitation parameters on the crystal morphology and size of transition metal struvite is poorly investigated. We reveal the effect of different reaction conditions on the crystal shape and crystallite size of M-struvites (NH4MPO4∙6H2O, M = Mg2+, Ni2+, Co2+). Furthermore, we characterize the coordination environment of the crystalline end products and their related phases [Co-dittmarite (COD) NH4CoPO4∙H2O and Co(II)phosphate octahydrate (CPO) Co3(PO4)2∙8H2O]. Mg- and Ni-struvite are stable in multiple concentrations of the educts and metal/phosphorus (M/P) ratios in contrast to Co-struvite which forms below M/P ratios of 0.4. A high M/P ratio with high concentrations of the educts decrease the crystallite size and idiomorphism of the crystals while low M/P ratios with low concentrations of the educts increase the crystallite size and the euhedral formation of the crystal planes. In the (Ni, Co)-solid solutions Ni and Co are homogenously distributed in the crystals with similar Ni# as in the aqueous solutions indicating no elemental fractionation in crystallization. Ni and Co-struvite exhibit a more centrosymmetric coordination environment compared to their related phases of COD and CPO determined by EXAFS. The CoO6 octahedron expands slightly the ideal size of the struvite structure and decomposes to Co-dittmarite. It is suggested that the crystallization of Ni- and Co-struvites follow a non-classical crystallization theory which consists of multiple nanophases on the way to the final crystal. T2 - SALSA Make and Measure... and Machines CY - Online meeting DA - 16.09.2021 KW - Crystal Engineering KW - Nucleation KW - Mesoporosity PY - 2021 AN - OPUS4-53444 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rautenberg, Max T1 - The Effect of Fluorine on Catalysts for the Oxygen Reduction Reaction obtained from Metal Organic Frameworks N2 - The oxygen reduction reaction (ORR) – an important reaction in electrochemical devices, such as fuel cells - is characterized by its sluggish kinetics and therefore requires catalysis. The industry currently relies on platinum as a catalyst, although it is scarce and expensive, hindering the commercial breakthrough of fuel cells in automotive applications. Platinum-free catalysts on basis of nitrogen- and metal doped carbons (NMCs) and fluorinated carbons are promising materials to replace platinum-based catalysts for the ORR. In this work we prepared six metal-organic frameworks (MOFs) by mechanical ball mill grinding and studied their formation by in-situ powder X-ray diffraction. Furthermore, the samples were carbonized under controlled conditions (900°C, 1h, N2-atmosphere) to yield carbon materials, that were employed in ORR-electrocatalysis. The effect of Co-doping and fluorination was systematically studied and outstanding ORR activity was found for the catalyst prepared from the Co-doped fluorinated ZIF-8. T2 - International Symposium on Fluorine-specific interactions CY - Berlin, Germany DA - 27.09.2021 KW - PGM-free catalyst KW - Oxygen Reduction Reaction KW - Mechanochemistry KW - MOFs PY - 2021 AN - OPUS4-53533 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rautenberg, Max T1 - Fluorination and co-doping of ZIF-8 by ball mill grinding for efficient oxygen reduction electrocatalysis N2 - The oxygen reduction reaction (ORR) is a common process in a variety of electrochemical devices, like fuel cells and metal air batteries. The sluggish kinetics of the ORR require an electrocatalyst to pass this bottleneck.[1] Currently, the most used catalytical systems are platinum-based, with several drawbacks, such as the high cost, low availability, and deactivation by CO poisoning.[2] Efforts are made to develop efficient, durable and low cost catalysts to promote the commercialization of fuel cells. Non-precious metal catalysts are promising candidates for efficient ORR catalysis. It has been shown that pyrolyzing metal organic frameworks (MOFs) under inert conditions yields carbon-rich materials, with evenly distributed metal sites, which possess promising electrocatalytic activity.[3] One widely used type of MOF as ORR catalyst precursors is the zeolitic imidazole framework (ZIF) where metal cations are linked through imidazole-based ligands. Their porous nature is partially retained after carbonization, making MOFs very suitable precursor materials. Herein we report the mechanochemical synthesis and structural analysis of Co-doped ZIF-8 (Zn), as well as two polymorphs (dense and prorous) of fluorinated Co-doped CF3-ZIF-8 (Zn). The samples showed electrochemical performance comparable to platinum after carbonization for 1 h at temperatures ranging between 850 – 1000°C. T2 - XXV General Assembly and Congress of the International Union of Crystallography - IUCr 2021 CY - Prague, Czech Republic DA - 14.08.2021 KW - PGM-free catalyst KW - Oxygen Reduction Reaction KW - Mechanochemistry KW - MOFs PY - 2021 AN - OPUS4-53535 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Linberg, Kevin T1 - Tipping the Energy Scales to Control Mechanochemical Polymorphism N2 - Control of ball milling conversions is required before the full potential of mechanochemical processing can be realized. It is well known that many parameters affect the outcome of mechanochemical polymorphism, but the energy of ball milling itself is often overlooked. We show here how this parameter alone can exert a significant influence on the polymorphic outcome of ball mill grinding by allowing the selective isolation of two polymorphic forms in their pure form under the same grinding conditions. Furthermore, we show how apparent mechanochemical equilibria can be deceptive. Our results clearly demonstrate the need for careful design and interpretation of ball milling experiments beyond current thinking. T2 - SALSA make and measure CY - Online meeting DA - 16.09.2021 KW - Mechanochemistry KW - Energy KW - Polymorph KW - Cocrystal PY - 2021 AN - OPUS4-53293 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Linnemann, Konrad A1 - Ballheimer, Viktor A1 - Sterthaus, Jens A1 - Wille, Frank T1 - Methodological aspects for finite element modelling of lid systems for type B(U) transport packages N2 - The regulatory compliance of the containment system is of essential importance for the assessment process of Type B(U) transport packages. The requirements of the International Atomic Energy Agency safety standards for transport conditions imply high loading on the containment system. The integrity of the containment system has to be ensured in mechanical and thermal tests. The containment system of German spent nuclear fuel and high level waste transport packages usually includes bolted lids with metal gaskets. The finite element (FE) method is recommended for the analysis of lid systems according to the guideline BAM-GGR 012 for the assessment of bolted lid and trunnion systems. The FE analyses provide more accurate and detailed information about loading and deformation of such kind of structures. The results allow the strength assessment of the lid and bolts as well as the evaluation of relative displacements between the lid and the cask body in the area of the gasket groove. This paper discusses aspects concerning FE simulation of lid systems for type B(U) packages for the transport of spent nuclear fuel and high level waste. The work is based on the experiences of the BAM Federal Institute for Materials Research and Testing as the German competent authority for the mechanical design assessment of such kind of packages. The issues considered include modelling strategies, analysis techniques and interpretation of results. A particular focus of this paper is on the evaluation of the results with regard to FE accuracy, influence of the FE contact formulation and FE modelling techniques to take the metallic gasket into account. KW - Transport cask KW - Closure system KW - Boiled joints KW - Numerical analysis PY - 2012 DO - https://doi.org/10.1179/1746510913Y.0000000021 SN - 1746-5095 SN - 1746-5109 SN - 0957-476X VL - 23 IS - 3-4 SP - 211 EP - 216 PB - Ramtrans Publ. CY - Ashford AN - OPUS4-29996 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hörmann, Anja Franziska T1 - Next Level Grazing Incidence, Part I: Standardization of Calibration and Alignment for Grazing Incidence Small-Angle (X-ray) Scattering N2 - We present initial results of our survey on grazing incidence methods which focuses on hardware, software, sample alignment and instrument calibration. We illustrate both sample alignment and sample-to-detector distance calibration with data recorded at the MOUSE and conclude with promising results from our Bayesian beam optimization procedure based on Gaussian Process regression. T2 - XIX edition of the International Small-Angle Scattering Conference (SAS2024) CY - Taipei, Taiwan DA - 04.11.2024 KW - Standardisation KW - Grazing incidence KW - Sample alignment KW - Instrument calibration PY - 2024 AN - OPUS4-62775 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Karafiludis, Stephanos A1 - Kochovski, Z. A1 - Scoppola, E. A1 - Retzmann, Anika A1 - Hodoroaba, Vasile-Dan A1 - ten Elshof, J. E. A1 - Emmerling, Franziska A1 - Stawski, Tomasz Maciej T1 - Nonclassical Crystallization Pathway of Transition Metal Phosphate Compounds N2 - Here, we elucidate nonclassical multistep crystallization pathways of transition metal phosphates from aqueous solutions. We followed precipitation processes of M-struvites, NH4MPO4·6H2O, and M-phosphate octahydrates, M3(PO4)2·8H2O, where M = Ni, Co, or NixCo1–x, by using in situ scattering and spectroscopy-based techniques, supported by elemental mass spectrometry analyses and advanced electron microscopy. Ni and Co phosphates crystallize via intermediate colloidal amorphous nanophases, which change their complex structures while agglomerating, condensing, and densifying throughout the extended reaction times. We reconstructed the three-dimensional morphology of these precursors by employing cryo-electron tomography (cryo-ET). We found that the complex interplay between metastable amorphous colloids and protocrystalline units determines the reaction pathways. Ultimately, the same crystalline structure, such as struvite, is formed. However, the multistep process stages vary in complexity and can last from a few minutes to several hours depending on the selected transition metal(s), their concentration, and the Ni/Co ratio. KW - Non-classical crystallization theory KW - Transition metals KW - Phosphates KW - Amorphous phases KW - Intermediate phases PY - 2023 DO - https://doi.org/10.1021/acs.chemmater.3c02346 SN - 1520-5002 VL - 35 IS - 24 SP - 10645 EP - 10657 PB - American Chemical Society (ACS) CY - Washington D.C. AN - OPUS4-59135 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Noack, J. A1 - Emmerling, Franziska A1 - Kirmse, H. A1 - Kemnitz, E. T1 - Sols of nanosized magnesium fluoride: formation and stabilisation of nanoparticles N2 - The formation of magnesium fluoride sols and xerogels according to the fluorolytic sol–gel synthesis based on the reaction of Mg(OMe)2 with non-aqueous HF has been thoroughly investigated by X-ray scattering (WAXS/XRD), TEM, SAXS, DLS and 19F MAS NMR spectroscopy. Mechanistic insights were gained by following the reaction progress and formation of intermediate phases of the fluorination of magnesium alkoxides. For F:Mg ratios of 0.3 and 0.4 the formation of two crystalline phases was observed containing the recently obtained compound [Mg6F2(OCH3)10(CH3OH)14] hexanuclear dicubane units. The stoichiometric reaction yields magnesium fluoride nanoparticles with crystallite sizes below 5 nm, which show broad reflections in the X-ray diffraction pattern. Metal fluoride sols prepared by this way undergo tremendous changes over the first several weeks after synthesis. Immediately after the fluorination, particles of about 120 nm—probably agglomerates—are formed, which break apart in the course of about one month of ageing and low-viscous, transparent sols with particles of about 12 nm are obtained. At the same time structural re-organisation processes within the magnesium fluoride particles are observed by an increase of the (110) reflection in WAXS. KW - Surface modification KW - Colloidal particles KW - Gold nanoparticles KW - Gel synthesis KW - Small-angle scattering KW - Oxide KW - Polyelectrolytes KW - Aggregation KW - Dispersion PY - 2011 DO - https://doi.org/10.1039/c1jm11943e SN - 0959-9428 SN - 1364-5501 VL - 21 IS - 38 SP - 15015 EP - 15021 PB - Royal Society of Chemistry CY - Cambridge AN - OPUS4-26183 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schlegel, Moritz-Caspar A1 - Wenzel, Klaus-Jürgen A1 - Sarfraz, Adnan A1 - Panne, Ulrich A1 - Emmerling, Franziska T1 - A wall-free climate unit for acoustic levitators N2 - Acoustic levitation represents the physical background of trapping a sample in a standing acoustic wave with no contact to the wave generating device. For the last three decades, sample holders based on this effect have been commonly used for contact free handling of samples coupled with a number of analytical techniques. In this study, a wall-free climate unit is presented, which allows the control of the environmental conditions of suspended samples. The insulation is based on a continuous cold/hot gas flow around the sample and thus does not require any additional isolation material. This provides a direct access to the levitated sample and circumvents any influence of the climate unit material to the running analyses. KW - Acoustic levition PY - 2012 DO - https://doi.org/10.1063/1.4705968 SN - 0034-6748 SN - 1089-7623 VL - 83 IS - 5 SP - 055101-1 EP - 055101-3 PB - American Institute of Physics CY - Melville, NY AN - OPUS4-25881 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gärtner, Stefanie A1 - Carvalho, J.J. A1 - Emmerling, Franziska A1 - Garbe, L.-A. A1 - Schneider, Rudolf T1 - Polyclonal murine and rabbit antibodies for the bile acid isolithocholic acid N2 - Bile acids are relevant markers for clinical research. This study reports the production of antibodies for isolithocholic acid, the isomer of the extensively studied lithocholic acid. The IgG titer and affinity maturation were monitored during the immunizations of three mice and two rabbits. In both animal models, polyclonal antibodies with a high selectivity and affinity were produced. The development of a direct competitive ELISA with a test midpoint of 0.69 ± 0.05 µg/L and a measurement range from 0.09–15 µg/L is reported. Additionally, the crystal structure of isolithocholic acid is described for the first time. KW - ELISA KW - Crystal structure KW - Competitive assay KW - Immunization monitoring KW - 3ß-hydroxy-5ß-cholanic acid PY - 2015 DO - https://doi.org/10.1080/15321819.2014.924419 SN - 1532-1819 SN - 1532-4230 VL - 36 IS - 3 SP - 233 EP - 252 PB - Taylor & Francis CY - Philadelphia, Pa. AN - OPUS4-31836 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Altmann, Korinna A1 - Schulze, Rolf-Dieter A1 - Friedrich, Jörg Florian T1 - Polymer deposition morphology by electrospray deposition - Modifications through distance variation N2 - Electrospray deposition (ESD) of highly diluted polymers was examined with regard to the deposited surface structure. Only the flight distance (flight time) onto the resulting deposited surface was varied from 20 to 200 mm. An apparatus without any additional heating or gas flows was used. Polyacrylic acid (PAA) and polyallylamine (PAAm) in methanol were deposited on Si wafers. The polymer layers were characterized by scanning electron microscopy, X-ray photoelectron spectroscopy, derivatization reactions and Fourier transform infrared spectroscopy using a grazing incidence unit. SEM images illustrated the changing structures of PAA and PAAm. For PAA the deposited structure changed from a smooth film (20 mm) to a film with individual droplets on the coated surface (100 mm and 200 mm), while for PAAm individual droplets can be seen at all distances. The ESD process with cascades of splitting droplets slows down for PAA after distances greater than 40 mm. In contrast, the ESD process for PAAm is nearly stopped within the first flight distance of 20 mm. Residual solvent analysis showed that most of the solvent evaporated within the first 20 mm capillary-sample distance. KW - Electrospray ionization KW - Electrospray deposition KW - Ultra-thin layers KW - Capillary-sample distance KW - Residual solvent PY - 2014 DO - https://doi.org/10.1016/j.tsf.2014.06.020 SN - 0040-6090 VL - 564 SP - 269 EP - 276 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-31252 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Altmann, Korinna A1 - Schulze, Rolf-Dieter A1 - Hidde, Gundula A1 - Friedrich, Jörg-Florian T1 - Electrospray ionization for deposition of ultra-thin polymer layers – principle, electrophoretic effect and applications N2 - Nebulizing of polymer solutions, in a high-voltage field under atmospheric conditions by electrospray ionization (ESI), is a comfortable way to deposit ultra-thin layers of polar or ionic polymers onto any conductive substrate materials. The substrate is grounded and the polymer solution is sprayed through a powered capillary. The formed charged droplets shrink by solvent evaporation during their way to the grounded substrate, the charges close ranks and the droplets collapse consecutively by charge repulsion, thus forming finally charged single macromolecules. After their discharging at the grounded substrate, an ultrathin ‘quasi-monomolecular’ polymer layer is formed. It could be shown by imaging of scratches through the polymer layer by atomic force microscopy that the deposited polymer layers are dense at a thickness of about 10 nm. Carbon fibre bundles were coated with poly (allylamine) (PAAm) or poly(acrylic acid) (PAA) as potential adhesion-promoting layers in fibre–polymer composites. The polymer deposition is self-inhibiting after formation of a continuous coverage of about 200 nm for PAAm and 30 nm for PAA as result of surface charging. Continuous deposition onto such isolating layers or polymers without charging can be achieved by using current of alternating polarity. The film formation is self-healing because of the electrophoretic effect, i.e. the ion discharging occurs preferentially at noncoated areas. This electrophoretic effect of ESI was demonstrated by completely enwrapping all the carbon fibres of the roving within a distance of about 100 μm far from its outside and also at the backside of the fibre bundle with about 80% of the topside coverage, as measured by X-ray photoelectron spectroscopy and visualized using scanning electron microscopy. KW - Complete enwrapping of fibres KW - Ultra-thin polymer layers KW - Self-healing KW - Electrospray deposition KW - Carbon fibres KW - Electrophoretic effect PY - 2012 DO - https://doi.org/10.1080/01694243.2012.727170 SN - 0169-4243 VL - 27 IS - 9 SP - 988 EP - 1005 PB - Taylor & Francis CY - London AN - OPUS4-42631 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stroh, Julia A1 - Emmerling, Franziska ED - Plank, J. ED - Lei, L. T1 - Direct insight into the admixture activity during cement hydration using levitated droplets N2 - Chemical admixtures are widely used to adjust properties of the cementitious mixtures. Different superplasticizers (SP) are typically added to improve the flowability of the fresh cement paste. Their working period is the initial stage of the cement hydration from its beginning until stiffening. Currently, polycarboxylate-based SP (PCE-SP) are the most effective ones. They can act beyond their aimed function causing changes in the hydration course, e. g. retardation effects. The exact mechanisms and influencing factors are still under investigation. However, the occurrence of the retardation effect indicates the involvement of PCE in the hydration reactions. Some observations indicate, that the retardation depends on the type, molecular structure and concentration of PCE, and the presence of other admixtures (stabiliser, ST). These factors influence further the working time of admixture and its amount related efficacy in the flow improvement. We investigate the cement hydration process in situ in levitated droplets. High resolution synchrotron X-ray diffraction allows gathering temporal course of the hydration reactions. The measurement setup is based on an ultrasonic levitator allowing in situ investigation of the temporal changes of the phase composition in the hydrating cementitious system. Further, the hydration can be followed ab initio avoiding the time loss for the sample preparation and filling in the sample holder. The collected data allows to conclude about the mechanisms of the admixture action and their involvement into the ongoing hydration process. T2 - 2nd International Conference on Polycarboxylate Superplasticizers (PCE 2017) CY - München, Germany DA - 28.09.2017 KW - Portland cement KW - Initial hydration KW - Acoustic levitator KW - Admixtures KW - Time resolution PY - 2017 SN - 978-3-9816240-6-9 SP - 185 EP - 193 AN - OPUS4-43167 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Chulvi Iborra, Katherine T1 - Pd(II)-LMOF based material for the sensing of molecular hydrogen in gas phase N2 - Current interest in hydrogen gas as an energy source is growing due to its attractive properties such as high chemical energy density and the fact that its combustion produces water as by-product, qualifying this gas as an appealing clean energy source. In particular, the use of molecular hydrogen in automotive applications such as the hydrogen internal combustion engine (HICE) or hydrogen fuel cells is an excellent clean alternative. Despite these promising opportunities, hydrogen gas has a distinct disadvantage as an everyday energy medium, that is, it is highly flammable. Hydrogen processing apparatuses should therefore be constantly monitored so that leaks are immediately detected. The implementation of direct sensing systems for H2(g) is thus a decisive factor for its application and acceptance as a clean energy source. Because the automotive market alone is already a mass market, these sensors do not only have to be reliable, robust and dimensionally small, but operation has to be simple and the device itself cost-effective. In addition, very low detection limits are a must as already escape of small quantities of H2(g) is directly related to public health and safety. Besides electrochemical or semiconductor sensors, optical sensors are especially appealing because the equipment is usually simple and accessible, easily miniaturized and measurements can be performed in situ and in real time. If one cannot rely for instance on metallic palladium as interacting matrix, a major challenge for optochemical hydrogen sensors is to find a suitable material that fulfils all the requirements mentioned above and undergoes a dedicated indication reaction with H2(g). One such alternative can be Metal-Organic Frameworks (MOFs) which constitute a predefined, organized, mesoporous structure built up from metal ions and organic bridging ligands. With a myriad of building blocks being available, MOFs can be equipped with internal H2 reception sites that shall allow for selective and sensitive indication. For instance, if Pd ions are implemented in such a way that they express open metal sites (OMS), these OMS shall possess a strong affinity for hydrogen. If light absorbing and emitting organic ligands are additionally chosen, luminescent MOFs (LMOFs) can result that are perfect candidates for optical sensors, as changes at the analyte reception site can be effectively transduced into a measurable signal. In this contribution, we intended to discuss the development of a new luminescent sensor material for the detection of the highly flammable H2(g). This sensor material is based on an LMOF assembled from Pd(II) and aromatic bridging ligands, the advent of hydrogen at the OMS in the LMOF producing distinct variations in the material’s optical properties. T2 - 24th Congress and General Assembly of the International Union of Crystallography CY - Hyderabad, India DA - 21.08.2017 KW - Optical sensor KW - Hydrogen KW - LMOF PY - 2017 UR - http://www.iucr2017.org/abstract/myaccount/pdf/iucr2017-abstract-0b61b4c101d7bf652ae5b0dffd66e5fd.pdf AN - OPUS4-42362 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wurzler, Nina T1 - Changes in the passive film chemistry on stainless steels during microbiologically influenced corrosion: A combined electrochemistry and XANES study N2 - Metal reducing bacteria (MRB) are capable of utilizing different metals, such as iron, chromium, manganese or uranium as well as many organic compounds, as electron acceptors for their metabolism. Via direct and indirect electron transfer processes MRB are able to convert insoluble passive film species like Fe(III)-oxides to soluble Fe(II)-oxides and hydroxides. This weakening of the passive film not only leads to an acceleration of the general corrosion processes, but also increases the susceptibility of stainless steels to pitting corrosion. Electron transfer mechanisms are not yet fully understood and the role of bacteria in corrosion processes is controversially discussed in the literature. Moreover, recent research indicates that the secretion of electron shuttles like riboflavins by MRB also contributes to the extracellular electron transfer. This project aims at clarifying the chemical and electrochemical interaction mechanisms of MRB with stainless steel surfaces. To investigate the changes in the oxide chemistry on the stainless steel surface in the presence of biomolecules and MRB a new flow cell has been designed and constructed which enables the collection of XANES (X-ray Absorption Near Edge Structure) spectra in fluorescence mode at the Fe K-edge and electrochemical analysis. Availability of oxygen and the pre-exposure of the MRB to Fe(III) during cultivation have been investigated as parameters with significant effect on the corrosion rates. XANES analysis is supplemented by ex-situ X-Ray Photoelectron Spectroscopy (XPS) and Fourier Transform Infrared Reflection Absorption Spectroscopy (FT-IRRAS) to complete the surface characterisation in terms of the oxide chemistry and the composition of organic residues. Complementary electrochemical quartz crystal microbalance (e-QCM) measurements have been performed to quantify the kinetics of bacterial attachment and biofilm formation. Together with the frequency shift, the evolution of the dissipation signal has been analyzed to investigate the changes in viscosity and structure of the biofilm from initial stages up to maturation. Scanning Electron Microscopy (SEM) and Atomic Force Microscopy (AFM) has been used to study the structure and viscoelastic properties of the biofilms after e-QCM experiments. The presentation will summarize our results on the effects of individual surface and environment related parameters on the chemical/electrochemical interaction mechanisms of MRB leading to passive film degradation on stainless steel surfaces and provide useful insights from a fundamental aspect for the development of novel mitigation strategies for microbiologically influenced corrosion. T2 - EUROCORR 2017 & 20thICC CY - Prague, Czech Republic DA - 04.09.2017 KW - Microbiologically influenced corrosion (MIC) KW - XANES KW - Stainless steel KW - Corrosion PY - 2017 AN - OPUS4-43407 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Emmerling, Franziska T1 - New insights in formation pathways: in situ investigations of mechanochemical reactions N2 - Mechanochemistry is increasingly used for synthesizing soft matter materials including metal organic compounds and cocrystals.1 The ever-increasing interest in this method is contrasted by a limited mechanistic understanding of the mechanochemical reactivity and selectivity. Time-resolved in situ investigations of milling reactions provide direct insights in the underlying mechanisms.2,3 We recently introduced a setup enabling in situ investigation of mechanochemical reactions using synchrotron XRD combined with Raman spectroscopy. The specific combination allows to study milling processes comprehensively on the level of the molecular and crystalline structure and thus obtaining reliable data for mechanistic studies. In this contribution, I will discuss our recent results investigating the formation of (polymorphic) cocrystals and metal phosphonates.4 First investigations of a mechanochemical synthesis under controlled temperature which allow determining the activation barrier are presented. Furthermore, in situ Raman spectroscopy coupled with thermography revealed a low temperature increase during milling reactions due to the mechanical impact and clear temperature increases as a result of the reaction heat.5 Our results indicate that in situ investigation of milling reactions offer a new approach to tune and optimize mechanochemically synthesized compounds. T2 - International Conference on Mechanochemistry and Mechanical Alloying, INCOME 2017 CY - Kosice, Slovakia DA - 03.09.2017 KW - Mechanochemistry KW - In situ PY - 2017 AN - OPUS4-43564 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kulla, Hannes T1 - In situ investigations of a mechanochemical cocrystal formation by X-ray diffraction for two different milling jar materials N2 - Mechanochemistry has become a valuable method for the synthesis of new materials, especially for pharmaceutical cocrystals. The Advantages of fast reactions in high purity and yield face a lack of understanding the underlying mechanism. Therefore, in situ setups to study mechanochemical reactions have been established. Herein, we present an in situ investigation of the mechanochemical cocrystal formation of pyrazinamide (PZA) with pimelic acid (PM) using synchrotron XRD. Two new polymorphs of PZA:PM (1:1) were synthesized by milling the starting materials in milling jars of different materials. While Form I is only obtained using a steel jar, Form II can be obtained purely in jars made of Perspex. In situ XRD experiments reveal a direct formation of Form II in Perspex and an intermediate formation of Form II in steel jars converting to Form I upon further grinding. Heating experiments and DFT calculations predict that Form II is the thermodynamically more stable polymorph. Therefore, the reaction progress in the steel jar contradicts Ostwald’s rules of stages as the more stable Form II converts into the metastable Form I. Hence, mechanochemistry offers the possibility to synthesize new materials that cannot be obtained using conventional methods. T2 - Adlershofer Forschungsforum 2017 CY - HU-Berlin, Erwin-Schrödinger Zentrum, Germany DA - 10.11.2017 KW - Cocrystal KW - Mechanochemistry KW - Polymorph KW - In situ KW - Milling PY - 2017 AN - OPUS4-42956 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Akhmetova, Irina T1 - In situ investigation of mechanochemical syntheses of manganese phosphonates N2 - The exploration of metal phosphonates chemistry has gained great interest during the last decades, because of their structural diversity. Transition metal phosphonates are promising candidates for an application as electrocatalysts in oxygen reduction reactions (ORR). Here, we present the in situ investigation of mechanochemical syntheses of two different manganese phosphonates by synchrotron X-ray diffraction. Nitrilotri(methylenephosphonic acid) and N,N-Bis(phosphonomethyl)glycine were chosen as ligands. The liquid-assisted milling process can be divided into three steps, including an amorphous stage. One of the products has not been obtained by classical solution chemistry before. These metal phosphonates and/or their derivatives are considered to be active in electrochemical energy conversion. The verification of their applicability is one of the topics of our resent research. T2 - 9th International Conference on Mechanochemistry and Mechanical Alloying CY - Kosice, Slovakia DA - 03.09.2017 KW - Mechanochemistry KW - In situ KW - Metal phosphonate KW - XRD PY - 2017 AN - OPUS4-41920 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stroh, Julia T1 - Direct insight into the admixture activity during cement hydration using levitated droplets N2 - Chemical admixtures are widely used to adjust properties of the cementitious mixtures. Different superplasticizers (SP) are typically added to improve the flowability of the fresh cement paste. Their working period is the initial stage of the cement hydration from its beginning until stiffening. Currently, polycarboxylate-based SP (PCE-SP) are the most effective ones. They can act beyond their aimed function causing changes in the hydration course, e. g. retardation effects. The exact mechanisms and influencing factors are still under investigation. However, the occurrence of the retardation effect indicates the involvement of PCE in the hydration reactions. Some observations indicate, that the retardation depends on the type, molecular structure and concentration of PCE, and the presence of other admixtures (stabiliser, ST). These factors influence further the working time of admixture and its amount related efficacy in the flow improvement. We investigate the cement hydration process in situ in levitated droplets. High resolution synchrotron X-ray diffraction allows gathering temporal course of the hydration reactions. The measurement setup is based on an ultrasonic levitator allowing in situ investigation of the temporal changes of the phase composition in the hydrating cementitious system. Further, the hydration can be followed ab initio avoiding the time loss for the sample preparation and filling in the sample holder. The collected data allows to conclude about the mechanisms of the admixture action and their involvement into the ongoing hydration process. T2 - 2nd International Conference on Polycarboxylate Superplasticizers (PCE 2017) CY - München, Germany DA - 27.09.2017 KW - Portland cement KW - Initial hydration KW - Acoustic levitator KW - Admixtures KW - Time resolution PY - 2017 AN - OPUS4-43166 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stroh, Julia T1 - In situ cement hydration in levitated droplets N2 - Building materials consist of cement, water and chemical admixtures, which adjust cement paste properties. They can act beyond their aimed functions causing changes in hydration course. The mechanisms are still under investigation. We investigate cement hydration in levitated droplets using an ultrasonic levitator. Hydrate phase formation is followed in situ by synchrotron XRD. The data allows detailed conclusions about the mechanisms of the admixture action in the ongoing hydration reactions. T2 - 7th GACM Colloquium on Computational Mechanics CY - Stuttgart, Germany DA - 11.10.2017 KW - Portland cement KW - Hydration KW - Levitation KW - Admixtures PY - 2017 AN - OPUS4-43165 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ricking, M. T1 - Probennahmestrategie für die kontinuierliche Mikrokunststoff-Analyse in Oberflächengewässern N2 - Das Poster stellt erste Ergebnisse zur Mikroplastik-Probennahme mit einem Sedimentationskasten dar. T2 - Wasser 2019 CY - Erfurt, Germany DA - 24.05.2019 KW - Mikroplastik KW - Sedimentationskasten KW - Probennahme PY - 2019 AN - OPUS4-49069 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Emmerling, Franziska A1 - Villajos Collado, José Antonio A1 - Jagorel, Noëmie A1 - Reinsch, Stefan T1 - Increasing Exposed Metal Site Accessibility in a Co-MOF-74 Material With Induced Structure-Defects N2 - Metal-organic frameworks (MOFs) are promising nanoporous materials with many practical applications. This owes largely to their remarkable porosity and the presence of specific chemical functionalities, such as exposed metal sites (EMS). The MOF-74 structure is known for exhibiting one of the highest EMS densities among porous materials. Moreover, the inclusion of structural defects has been proposed to enhance activity further. This was previously achieved by mixing the original linker together with a second one, having lower topology. The presence of structural defects was evidenced by the resulting crystalline properties and thermal stability. In this work, different mixtures of tetratopic 2,5-dihydroxyterephthalic acid with up to 60% of the tritopic hydroxyterephtalic acid were used to synthesize crystalline Co-MOF-74-like materials. Materials synthesized from higher proportions than 30% of hydroxyterephtalic acid in the synthesis media collapse upon partial removal of the solvent molecules. This indicates the presence of structural defects and the importance of the solvent molecules in stabilizing the crystalline structures. Electron microscope images show that crystal size reduces with inclusion of hydroxyterephtalic acid as the second linker. The presence of coordinated solvent molecules at the EMS was evaluated by Fourier-transform infrared spectra (FTIR) spectroscopy, so that a higher degree of solvent-exchange was observed during washing for defective structures. Furthermore, TG analysis suggests defective structures exhibit lower desolvation temperatures than the defect-free structures. Finally, N2 adsorption-desorption analyses at −196°C showed an enhanced accessibility of the gas to the inner porosity of the defective structures and therefore, the EMS of the material. All these finding make this pathway interesting to enhance the potential interest of these materials for an industrial application because of both a facilitated activation and a better access to the active sites. KW - MOF-74 KW - Structural defects KW - Mixed-linkers KW - Exposed metal sites KW - Facilitated activation PY - 2019 DO - https://doi.org/10.3389/fmats.2019.00230 VL - 6 SP - 230 PB - Frontiers Media CY - Lausanne AN - OPUS4-49256 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kabelitz, Anke A1 - Dinh, H. A. A1 - Emmerling, Franziska T1 - Early stage in situ detection of polynuclear aluminum phases in aqueous solution N2 - Polynuclear cationic aluminum hydroxide phases are known intermediates in the formation of aluminum oxides or (oxide) ydroxides upon hydrolysis of aluminum salt solutions. In the presence of sulfate anions, these aluminum polyoxocations (Al13) can form crystalline Al13 sulfates with varying chemical composition. The formation of these Al13 sulfates in aqueous solution has been poorly understood. Here, we investigate the early stage crystallization of Al13 clusters in a sulfate-containing solution, in situ and in real time. Dynamics associated with Al13 sulfate formation have been obtained for the first time, using Synchrotron X-ray diffraction (XRD) of solutions suspended by acoustic levitation. Time-resolved in situ data show that the cubic phase, Na [(AlO4)Al12(OH)24(H2O)12](SO4)4*10H2O, forms after only minutes. The Formation mechanism of Al13 sulfates was found to depend on the sulfate:aluminum (SO4:Al) ratio. Ex situ XRD of the product Al13 sulfates in solution shows that for SO4:Al ratio ≤ 1.5 two other crystalline phases form, and convert to the cubic phase upon washing and drying. In situ XRD for the same ratio shows transient formation of an intermediate during the crystallization process. KW - Polyoxocation KW - In situ KW - Crystallization KW - Acoustic levitation KW - Synchroton x-ray diffraction PY - 2019 DO - https://doi.org/10.1016/j.poly.2019.05.049 VL - 170 SP - 639 EP - 648 PB - Elsevier Ltd. AN - OPUS4-48552 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Tumanov, I. A1 - Tumanov, E. A1 - Michalchuk, Adam T1 - Ball size or ball mass – what matters in organic mechanochemical synthesis? N2 - Ball mass is an important parameter that is known to have an influence on the outcome of a mechanochemical reaction induced by ball-milling. A standard way of modifying the ball mass is to change the size of the ball made of the same material. In this case, however, a change in mass is accompanied by a simulatneous change in the ball size. It is therefore not possible to disentangle the effects of mass and Surface area in these cases. In the present work we report the results of experiments with specially designed and manufactured balls in which (1) milling ball mass is held constant, but their size differs, and (2) the ball mass is altered, with the diameter of the milling ball being held constant. Using the cocrystallisation of theophylline + nicotinamide as a case study it was found that both diameter and ball mass play crucial roles in determining the rate of a mechanochemical reaction. For comparison, we have also used milling balls with the same size (different mass), and others with the same mass (different size) made of different materials, as would be “traditional”. It was found that, despite having the same size, the lightest milling ball (nylon) was the most efficient in initiating the co-crystallisation, presumably due to the sorption of EtOH. Hence, the results of this manuscript also demonstrate how milling ball material can in fact be the most influential parameter, and potentially counterintuitive to classical mechanics. KW - Mechanochemistry KW - XRD PY - 2019 DO - https://doi.org/0.1039/c8ce02109k VL - 21 SP - 2174 EP - 2179 PB - RSC Royal Society of Chemistry AN - OPUS4-47851 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Emmerling, Franziska T1 - New insights in cocrystal formations: in situ investigations of mechanochemical syntheses N2 - Mechanochemistry is increasingly used for synthesizing soft matter materials including metal organic compounds and cocrystals. The ever-increasing interest in this method is contrasted by a limited mechanistic understanding of the mechanochemical reactivity and selectivity. Time-resolved in situ investigations of milling reactions provide direct insights in the underlying mechanisms. We introduced a setup enabling in situ investigation of mechanochemical reactions using synchrotron XRD combined with Raman spectroscopy. The specific combination allows to study milling processes comprehensively on the level of the molecular and crystalline structure and thus obtaining reliable data for mechanistic studies. We discuss our recent results investigating the formation of (polymorphic) cocrystals. First investigations of a mechanochemical synthesis under controlled temperature which allow determining the activation barrier are presented.6 Furthermore, X-ray diffraction and in situ Raman spectroscopy coupled with thermography revealed a low temperature increase during milling reactions due to the mechanical impact and clear temperature increases as a result of the reaction heat. Our results indicate that in situ investigation of milling reactions offer a new approach to tune and optimize mechanochemically synthesized compounds. T2 - CSEC Seminar University of Edinburgh CY - Edinburgh, Scotland DA - 16.05.2019 KW - Mechanochemistry KW - Acoustic levitation KW - In situ PY - 2019 AN - OPUS4-48098 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - de Oliveira Guilherme Buzanich, Ana T1 - Structure analytics with Hard X-rays at the BAMline and µSpot beamlines N2 - An overview of the research areas at the structure analysis division is given. Specifically the in situ characterization of dynamic processes with hard X-ray diffraction and absorption spectroscopy at the BAMline and µSpot beamlines (BESSY-II). T2 - BAM-IFW Workshop CY - Dresden, Germany DA - 28.03.2019 KW - Structure analysis KW - X-ray Spectroscopy KW - Synchrotron KW - Beamline KW - Material characterization PY - 2019 AN - OPUS4-47695 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stroh, Julia T1 - In situ full phase analysis of the early cement hydration N2 - Fresh cement paste is a suspension consisting of a hydraulic binder (cement), water, and numerous minor components – admixtures. Addition of admixtures aims at specific modification of properties of the fresh cement paste or hardened cementitious building material. Specific admixtures, so-called superplasticizers (SP), are used to improve the flowability of the fresh cement paste with reduced water content. The latter is the starting material for the high-strength concrete. Thus, SPs are essential for the ambitious construction projects. However, uncontrollable retardation of the setting time in presence of SPs is occasionally observed. Obviously, SPs influence early products of the cement hydration leading to changes in the microstructure development. The hardening is thus delayed, and the quality of the resulting building material suffers. The mechanisms of the admixture action during the hydration process are still intensively investigated [1-7]. A detailed understanding of the admixture effects during the early hydration stage is the key to control and individual adjustment of the cement-based construction materials. We use the unique combination of the wall-free sample holder and the time-resolved X-ray scattering analysis to achieve the full information about the hydrate phases formed under the influence of admixtures. We use ultrasonic levitator to start the cement hydration in levitated cement pellets [8, 9]. The sample levitation allows collection of the unimpaired information about cement hydrate phases. The most beneficial is the avoiding of the contributions of the sample holder material to the data signal. We induce the cement hydration by adding water to unhydrated Portland cement during the data acquisition. The full phase composition of the hydrating cementitious system can be gathered in situ using wide angle X-ray scattering (WAXS). During the hydration of cement both crystalline and amorphous hydrate phases are formed. WAXS data contain the information about crystalline phases behind the Bragg reflections, whereas the amorphous hydrates influence the appearance of the background. Application of the data analysis specific for crystalline or amorphous phases is needed. The data quantification by the Rietveld method allows to conclude about the changes of the phase amounts due to the presence of admixture. The calculation of the pair distribution functions allows analysis of the amorphous hydrates. Based on this information, the SP effects and the extent of their involvement into the ongoing reactions can be concluded. A detailed understanding of the complex cement hydration process is envisioned. T2 - Anakon 2019 CY - Münster, Germany DA - 25.03.2019 KW - Cement KW - Admixtures KW - Pair Distribution Functions KW - X-ray diffraction KW - Total scattering analysis PY - 2019 AN - OPUS4-47664 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sturm, Heinz T1 - Notwendigkeit von (Realistischen) Referenzmaterialien N2 - Die Herstellung von Mikroplastik Referenzmaterialien wird vorgestellt. T2 - Statusfonferenz der BMBF Fördermassnahme "Plastik in der Umwelt" CY - Berlin, Germany DA - 09.04.2019 KW - Ringversuch KW - Mikroplastik KW - Referenzmaterialien PY - 2019 AN - OPUS4-47798 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rohner, C. T1 - Electron beam induced amorphisation of polypropylene particles N2 - Untersuchung von Polypropylen Nanopartikeln mittels REM. Es wird die Hypothese aufgestellt, dass mit der Paarverteilungsfunktion auf den Alterunszustand geschlossen werden kann. N2 - Analysis of polypropylene nanoparticles with scanning elektron spectroscopy (SEM). The poster describes the hypothesis that the pair distribution function determined by SEM can be used to deduce the state of polymer age. T2 - Microscopy characterisation of organic-inorganic interfaces 2019 CY - Berlin, Germany DA - 07.03.2019 KW - Nanopartikel KW - Mikroplastik-Analytik KW - Paarverteilungsfunktion KW - Pair distribution function KW - Nanoparticles KW - Microplastic analysis PY - 2019 AN - OPUS4-47890 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Haferkamp, Sebastian A1 - Emmerling, Franziska T1 - In situ investigations of mechanochemical reactions N2 - Mechanochemistry paves the way to simple, fast, and green syntheses. Despite considerable effort, there remains a lack in understanding of the underlying mechanisms. In situ investigations help to understand these mechanisms, which occur during a mechanochemical reaction. Here we present a universal strategy for simultaneous real-time in situ analysis, combining X-ray diffraction, Raman spectroscopy, and thermography. The potential of our approach is shown for different model reactions. T2 - ANAKON 2019 CY - Münster, Germany DA - 25.03.2019 KW - In situ KW - Mechanochemistry KW - Milling PY - 2019 AN - OPUS4-47701 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -