TY - CONF A1 - Alasonati, E A1 - Bartczak, D A1 - Altmann, Korinna A1 - Giovannozzi, A T1 - Towards Standardised Micro and Nanoplastics Analysis via Interlaboratory Comparisons: First Outlook of the VAMAS TWA 45 P3 Project N2 - This talk is part of the stakeholder workshop of the PlasticTrace project held in September 2025 in Oslo. The presentation shows first results of the VAMAS ILC on nanoplastics. PP nanoparticles were given to the participants. These were asked to measure the mass or particle number or size of the PP nanoplastics. Various techniques such as DLS, FFF, Py-GC/MS, TED-GC/MS, PTA were used. T2 - Stakeholder Workshop PlasticsTrace CY - Online meeting DA - 09.09.2025 KW - Nanoplastics KW - ILC KW - DLS KW - Polypropylene PY - 2025 AN - OPUS4-64714 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Becker, Roland T1 - Querschnittsthema Referenzmaterialien: Planung Ringversuche N2 - Nach einer Erläuterung der international üblichen Definitionen von Referenzmaterialien und Matrix-Referenzmaterialien erfolgt eine Zusammenfassung der spezifischen Anforderungen bei Herstellung und Charakterisierung. Weiterhin werden die unterschiedlichen Anforderungen an die Durchführung von Ringversuchen im Sinne eines Methodenvergleiches, einer Eignungsprüfung von Laboratorien und der Zertifizierung von Matrix-Referenzmaterialien gegenübergestellt. Für den aktuell geplanten ersten Ringversuch zur Quantifizierung von Mikroplastik in Schwebstoffen mittels thermischer Verfahren werden die konkreten technischen Bedingungen zur Herstellung entsprechender Referenzmaterialien einschließlich der Homogenitätsprüfung ihrer Mikroplastikgehalte dargestellt. Die Besonderheiten des Ringversuches vor dem Hintergrund einer Normung der eingesetzten Verfahren werden diskutiert. T2 - Forschungsschwerpunkt „Plastik in der Umwelt – Quellen • Senken • Lösungsansätze“: 2. Workshop des Querschnittsthemas „Analytik und Referenzmaterialien“ CY - Augsburg, Germany DA - 4.7.2018 KW - Mikroplastik KW - Referenzmaterialien KW - Ringversuche KW - Thermische Verfahren KW - Schwebstoffe KW - Methodenvergleich PY - 2018 AN - OPUS4-45681 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kittner, Maria T1 - Assessment of Microplastic Emissions from Artificial Turf Sports Pitches N2 - Following the recommendation of the European Chemicals Agency, on 25 September 2023 the European Commission passed a comprehensive new regulation to reduce emissions of microplastics (MP) into the environment, which includes the sale and use of intentionally added MP.1,2 This also applies to the application of synthetic rubber granulate infill in artificial turf systems and will ultimately have an impact on recreational sports. In Germany, rubber granulate made of ethylene-propylene-diene-monomer rubber (EPDM) is currently predominantly used. So far, there is no sufficient database for estimating MP emissions from artificial turf pitches into the environment and thus their relevance as a source of MP pollution.3 This topic is controversially discussed due to the complexity of sampling and analytics. To close this research gap, this project has the goal to determine mass balances for the emissions of MP from artificial turf pitches to allow an estimation of the amount of MP released per artificial turf pitch and year. Within this study, MP emissions of three artificial turf scenarios at different time states (unaged, artificially aged and real-time aged) are compared: the past (old turf: fossil based, synthetic infill), present (most commonly installed in Europe: fossil based, EPDM infill), and the future (turf with recycled gras fibres, no synthetic infill). To simulate the outdoor weathering during the lifespan of an artificial turf of approx. 15 years, brand-new artificial turf and EPDM rubber granulate were accelerated aged by means of UV weathering and mechanical stress. Potential MP emissions into surface and groundwater are simulated by lysimeter and shake experiments. MP mass contents are subsequently determined by Thermal Extraction Desorption Gas Chromatography/Mass Spectrometry. Using special microfilter crucibles allows the estimation of the particle sizes of the emitted MP, which is a fundamental requirement for an assessment of potential health hazards for humans. T2 - SETAC 2024 CY - Seville, Spain DA - 05.05.2024 KW - Mikroplastik KW - TED-GC/MS KW - Lysimeter KW - PAK KW - Schwermetalle PY - 2024 AN - OPUS4-60014 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hodoroaba, Vasile-Dan T1 - Micro and Nano Plastics in the Environment N2 - The VAMAS/TWA 45 Project 2 “Development of standardized methodologies for characterisation of microplastics with microscopy and spectroscopy methods” involving 85 participants around the world is primarily discussed with respect to the results received and a first data evaluation. Status of the Project "Guidelines for defining reference materials for plastic degradation in marine environment" is reported and two new project proposals are presented: "Development of standardized methodologies for characterisation of nanoplastics (starting soon, BAM as leader?) and "Development of analytical protocols for the identification and quantification of microplastics of fibrous shape (still in negotiation)". T2 - Versailles Project on Advanced Materials and Standards (VAMAS) 48th Steering Committee Meeting CY - New Delhi, India DA - 09.10.2023 KW - Microplastics KW - Nanoplastics KW - Interlaboratory comparison KW - VAMAS KW - Reference materials KW - ISO PY - 2023 UR - https://www.nplindia.org/index.php/amcsnzt_2023/ AN - OPUS4-58539 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Akhmetova, Irina A1 - Beyer, Sebastian A1 - Schutjajew, K. A1 - Tichter, T. A1 - Wilke, Manuel A1 - Prinz, Carsten A1 - B. Martins, Inês C. A1 - Al-Sabbagh, Dominik A1 - Roth, C. A1 - Emmerling, Franziska T1 - Cadmium benzylphosphonates - the close relationship between structure and properties N2 - Cadmium benzylphosphonate Cd(O3PBn)·H2O and its fluorinated derivates Cd(O3PBn-3F)·H2O, Cd(O3PBn-4F)·H2O, and Cd(O3PBn-F5)·H2O were synthesized mechanochemically. The Crystal structures of the compounds were determined based on powder X-ray diffraction (PXRD) data. The influence of the ligand substitution on the crystal structure of the metal phosphonate was determined. The hydrophobicity as a function of degree of fluorination was investigated using dynamic vapor sorption. KW - Mechanochemistry KW - Metal phosphonates KW - PXRD KW - DVS PY - 2019 DO - https://doi.org/10.1039/c9ce00776h VL - 21 SP - 5958 EP - 5964 PB - RSC Royal Society of Chemistry AN - OPUS4-49930 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Wessen Problem ist Mikroplastik eigentlich? N2 - In den letzten 20 Jahren ist die Aufmerksamkeit vieler Forschender sowie der Politik und der Bürger selbst auf ein wachsendes Kunststoffproblem unserer Zeit stark gestiegen. Mangelnde Wertstoffkonzepte, Sammelstellen und unbedachtes Einbringen von Kunststoffprodukten in die Umwelt führen dort zu einer Anreicherung. Durch äußere Witterungseinflüsse können diese Produkte degradieren und fraktionieren, so dass heute in allen Teilen der Welt Mikroplastik (1-1000 µm, ISO/TR 21960:2020) unterschiedlicher Polymermaterialien nachgewiesen werden kann. Bei Mikroplastik gilt das Vorsorgeprinzip. Die Partikel können weiter zerfallen in Nanoplastik (< 1 µm, ISO/TR 21960:2020). Ob eine toxikologische Gefährdung von Mikro- oder Nanoplastik ausgeht, wird vielfältig untersucht. Bisher stehen valide Ergebnisse aus. Untersuchungen zur Häufigkeit, dem Transport und möglicher Senken und Eintragspfade muss aber Rechenschafft getragen werden, so dass ein Monitoring von Mikroplastik bereits in der Revision der Trinkwasserrahmen-Richtlinie und der Abwasserrahmen-Richtlinie gefordert wird. Bedenklich ist auch die Verordnung über Mindestanforderungen an die Wasserwiederverwendung (2020/741), in welcher nicht verbindlich gesagt wird, Wasser welcher Reinigungsstufe eines Klärwerks auf die Felder zur Wiederverwendung aufgebracht werden darf. Einer Regulierung über die EU-Plastikstrategie hinaus mit z.B. Verboten für Einwegplastik-Produkte und Rezyklingquoten kann nur entgegengewirkt werden, wenn valide Messmethoden, Referenzmaterialien und Standards existieren, die das tatsächliche Ausmaß von Mikroplastik-Konzentrationen in Luft, Wasser, Boden und Biota zuverlässig und genau aufzeigen. T2 - Technomer CY - Chemnitz, Germany DA - 06.11.2025 KW - Mikroplastik KW - Referenzmaterial KW - TED-GC/MS PY - 2025 AN - OPUS4-64618 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Misra, Archismita T1 - Polyoxometalate Ionic Liquids as Protective Coatings for Industrial Infrastructure and Cultural Heritage against Microbiologically Influenced Corrosion (MIC) N2 - Corrosion of stone and metal due to acid rain and biodeterioration poses significant challenges for industrial and residential infrastructure, as well as cultural heritage, including statues and historical artefacts. A promising mitigation strategy involves thin, transparent films of polyoxometalate-based ionic liquids (POM-ILs) as chemical shields. Stone samples coated with acid-resistant, biocidal POM-ILs exhibited negligible corrosion when exposed to simulated acid rain, in stark contrast to the severe deterioration of unprotected samples. Additionally, their biocidal properties effectively prevent biofilm formation on coated surfaces. Following studies successfully explored the effectiveness of the coating against lampenflora growing in the Pommery Champagne cellar; and the long-term performance of POM-ILs under outdoor environmental conditions. So, POM-ILs have already demonstrated remarkable anticorrosion and antimicrobial properties against aerobic microorganisms and, being water-insoluble, do not leach into aquatic ecosystem. The current research project repurposes the POM-ILs, extending their application to metals, specifically targeting microbiologically influenced corrosion (MIC) in cultural heritage artefacts made of brass, carbon steel, cast iron, and bronze. This involves optimizing nanocoating adhesion to the metal surface and evaluating its protective efficacy against MIC caused by anaerobic microorganisms such as methanogenic archaea and sulfate reducing bacteria (SRB). This presentation will highlight POM-ILs as sustainable, high-performance nanocoatings for biocorrosion mitigation. It will showcase published success stories, discuss ongoing research and proof-of-concept results, and explore future prospects for these advanced materials in safeguarding metal infrastructure and artefacts across different industrial sectors as well as in the context of cultural heritage conservation. T2 - 10th International symposium on applied microbiology and molecular biology in oil systems (ISMOS10) CY - Nashville, Tennessee, USA DA - 11.08.2025 KW - Polyoxometalates KW - Corrosion KW - Microbiologically Influenced Corrosion KW - Ionic Liquid PY - 2025 AN - OPUS4-64548 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dailey, L. A. A1 - Altmann, Korinna A1 - Ćirković Veličković, Tanja T1 - Exposition und Detektionstechniken: Der Weg zur Harmonisierung N2 - Der Vortrag gibt einen Überblick über Erkenntnisse der WG 1 und WG 3 des CUSP Clusters der Horizon Europe Projekte von Mikroplastik (2020-2025). Die Frage ist wie hoch ist die Exposition und ist das dann eine gesundheitliche Gefahr. Diskutiert werden Mechanismen, die helfen richtig und genau zu messen, z.B. Prozesskontrollen oder Referenzmaterialien. Es wird ein Weg zu mehr Harmonisierung im Bereich der Mikroplastik-Analytik aufgezeigt. T2 - Mikroplastik – Was wissen wir heute? BfR-Forum Verbraucherschutz CY - Berlin, Germany DA - 02.12.2025 KW - Microplastics KW - Reference materials KW - Harmonisation PY - 2025 AN - OPUS4-65330 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Textile Fibers as Reference Materials for Microplastic Release N2 - Fibers of textile origin are named as high contributor for microplastic pollution in the environment next to e.g. plastics from packaging, tire wear and paints. Small fibers and fragments (microplastics: 1-1000 µm) can be released from textiles by mechanical abrasion during application (e.g. wearing) or washing. To date, the occurrence, transport pathways, and impacts of such small fibers on the environment and human health remain unclear. The European Commission revised the Urban Wastewater Treatment Directive (Directive (EU) 2024/3019) and made monitoring of microplastics mandatory in the next years. Additionally, standards for microplastic detection are developed in the ISO standardization body ISO/TC 147/SC 2 with the documents ISO/DIS 16094-2 and ISO/DIS 16094-3. Detection mainly occurs by thermoanalytical methods for mass or vibrational methods with microscopes for numbers. Such standards and regulatory efforts need validated methods, which themselves need reference materials for validation. Reference materials are well characterized materials that are produced for a specific purpose and are homogeneous and stable within one property of interest. The shape and the composition of the reference particles/fibers will affect the detection, hence it is important to validate the instruments with fibers, if this is the task for monitoring campaigns. This work describes the production of realistic fibers as reference material for microplastic analysis. The individual samples contain of a small number (< 1000) and mass (< 20 µm) of fibres. Homogeneity and stability control occurred by thermogravimetric analysis and µ-Raman. Further characteristics were determined for type, shape and size distribution. T2 - TEXTEH CY - Bucharest, Romania DA - 23.10.2025 KW - Microplastics KW - Reference materials KW - Microfibers KW - Microfiber release PY - 2025 AN - OPUS4-64620 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Production of reference materials using a quality by design approach N2 - Accurate analysis of microplastics is based on validated methods and the use of standardized protocols. Therefore, reference materials are essential to determine recovery rates and optimise the existing workflows. The reference materials should mimic the reality in terms of particle properties and concentration and are intended for a special use. The Quality-by-Design approach helps to select the users need and defines a target product profile with mandatory and desired particle properties. We will address different reference material top-down production processes with their limits and challenges for production of materials varying in size ranges of micro- and nanoplastics. T2 - OECD Workshop on Nanoplastics CY - Paris, France DA - 12.11.2025 KW - Microplastics KW - Reference materials KW - Nanoplastics KW - Quality-by-Design PY - 2025 AN - OPUS4-64717 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute T1 - Assessment of Microplastic and Contaminant Emissions from Artificial Turf Sports Pitches N2 - Due to their advantages over natural gras, artificial turf sports pitches are well established in popular sports and their number is increasing every year. This raises questions about potential pollutant emissions and possible risks to the environment due to its transfer to soil and groundwater. The main sources of emissions are the rubber infill granules and the abrasion of grass fibers. While estimates on the transfer of pollutants to the soil are already available, there is still insufficient data on the discharge of microplastics from artificial turf systems and thus on the assessment of its relevance for the soil. To close this gap, the pollutant emissions of three artificial turf scenarios - past (fossil-based, rubber infill), present (most frequently installed in Germany, rubber infill) and future (turf with recycled grass fibers, no rubber infill) - were compared in different ageing states (unaged, accelerated, and real time aged). Accelerated ageing consisting of UV weathering and mechanical stress was applied to simulate the outdoor weathering of turf systems during their service life span of approx. 15 years. Emissions of microplastics and environmentally relevant pollutants were sampled simultaneously using newly developed, innovative lysimeters. The microplastics contents were determined using Thermal Extraction-Desorption Gas Chromatography/Mass Spectrometry (TED-GC/MS). In addition, the concentrations of PAH and heavy metals were determined. T2 - Jahrestag der Deutschen Bodenkundlichen Gesellschaft CY - Tübingen, Germany DA - 14.09.2025 KW - Artificial Turf KW - Microplastics KW - Contaminants PY - 2025 AN - OPUS4-65022 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ryll, Tom William T1 - Researching automation of gypsum recycling N2 - This poster illustrates the recent work on a setup for automated in-situ analysis of gypsum recycling processes. Analysis in synchrotron X-rays, Raman- and UV-vis spectroscopy are made possible with this compact and mobile setup. First results from Raman spectroscopy on the conversion of gypsum to bassanite in hypersaline solutions are presented and future plans on optimization are formulated. T2 - ANAKON 2025 CY - Leipzig, Germany DA - 10.03.2025 KW - Recycling KW - Automation KW - Synchrotron-X-ray-diffraction KW - Raman-spectroscopy KW - Gypsum PY - 2025 AN - OPUS4-62706 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Speight, Isaiah R. A1 - Ardila-Fierro, Karen J. A1 - Hernández, José G. A1 - Emmerling, Franziska A1 - Michalchuk, Adam A1 - García, Felipe A1 - Colacino, Evelina A1 - Mack, James T1 - Ball milling for mechanochemical reactions N2 - Mechanochemistry is an emerging field with the potential to pave the way for sustainable chemistry. Although the use of mechanical force to initiate chemical reactions has been recognized for millennia, it has often taken a backseat to thermal and photonic methods. Over the past 30 years, mechanochemistry has seen a resurgence of interest, attracting researchers across the globe. Despite its proven ability to address numerous challenges within the chemical community, mechanochemistry remains on the periphery. This Primer serves as a valuable guide for conducting mechanochemical reactions by ball milling, offering an overview of the processes, methods, tools and terminology necessary to embark on research in this field. It also highlights persistent hurdles such as equipment standardization, understanding the impact of new discoveries and the lack of predictability of reaction outcomes. The Primer’s focus is on how mechanochemical ball milling is used in various chemical transformations, distinguishing it from other forms of mechanochemistry discussed in the literature. With a promising future, this Primer serves as a gateway for those aspiring to contribute to the field’s advancement. KW - Mechanochemistry KW - Ball milling KW - Upscaling PY - 2025 DO - https://doi.org/10.1038/s43586-025-00401-2 SN - 2662-8449 VL - 5 IS - 1 SP - 1 EP - 18 PB - Springer Science and Business Media LLC AN - OPUS4-63447 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Michalchuk, Adam A1 - Delogu, Francesco T1 - Fundamental basis of mechanochemical reactivity N2 - This themed collection includes a collection of articles on the fundamental basis of mechanochemical reactivity. KW - Mechanochemical KW - Metal-organic KW - Transformation KW - Dimerization PY - 2024 DO - https://doi.org/10.1039/d4cp90153c SP - 1 EP - 3 PB - Royal Society of Chemistry (RSC) AN - OPUS4-61500 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Emmerling, Franziska A1 - Michalchuk, Adam A1 - Casali, Lucia A1 - May, Anastasia T1 - Real-Time Monitoring and Temperature Control for Optimized Polymorph Engineering N2 - Integrating real-time monitoring with precise temperature control and mechanochemical processing represents a transformative approach to the controlled engineering of polymorphic forms in molecu-lar solids. Combining these methodologies overcomes the limitations of traditional solution-based or purely thermal approaches, enabling access to metastable or otherwise elusive polymorphs under milder and more sustainable conditions. Recent studies have shown that mechanochemical trans-formations proceed through distinct kinetic stages, including prolonged induction periods that can be tuned by adjusting the mechanical energy input[1]. These induction periods are associated with pro-cesses of mechanical activation, such as the accumulation of defects and increased surface energy, which lower the effective energy barriers for polymorphic transitions. Crucially, it is the total accumu-lated mechanical energy, rather than the duration or intensity of milling alone, that dictates the onset of polymorphic conversion, offering a new dimension of kinetic control[2-5]. Variable temperature ball milling reveals that the temperature required to induce polymorphic trans-formations can be significantly lower than under conventional thermal methods. For instance, tran-sitions that typically require high temperatures under equilibrium conditions can be achieved at sub-stantially lower temperatures in the presence of mechanical activation. This has been demonstrated in cocrystal systems such as nicotinamide-pimelic acid and isonicotinamide-glutaric acid, where the transition temperature was lowered by up to 25°C[2,3]. Real-time, in situ powder X-ray diffraction and temperature monitoring are essential for capturing transient phases and elucidating the interplay between thermal and mechanical effects. This confirms that combining mechanical energy with con-trolled temperature not only accelerates transformation kinetics, but also expands the accessible polymorphic landscape [2,3]. Collectively, these advances underscore the potential of real-time monitored, temperature-controlled mechanochemistry as a robust platform for the selective design and manufacturing of polymorphs. This approach provides unprecedented control over solid-state reactivity and opens new avenues for the sustainable and targeted engineering of functional materials and pharmaceuticals. T2 - 13th Bologna´s convention on Crystal Forms - CF@Bo n.13 University of Bologna CY - Bologna, Italy DA - 07.09.2025 KW - Plymorhism KW - Pre-activation PY - 2025 AN - OPUS4-64839 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wiesner, Yosri T1 - Microplastics in composts - Identification and quantification of microplastic contents using a thermal decomposition method N2 - The ubiquitous presence of unintended plastics in the environment has been an issue in scientific studies and public debate. Recent studies on MP findings are focused mainly on aquatic systems, while little is known about MP in terrestrial ecosystems. Fermentation residues, sewage sludge and compost are secondary raw material fertilizers and represent a possible input path of plastics in soils. Soils are final sinks for micro plastics. In this context, samples were taken in a combined fermentation and composting plant in Germany to get real compost samples which were investigated. Existing regulations include requirements for total contents of plastics in combination with visual determination methods. In order to avoid possible underdeterminations, precise detection methods should be used in the future from a scientific point of view. For this reason, the use of thermoanalytical detection is an appropriate way. Spectroscopic methods such as Raman or FTIR are not suitable for determining the mass content of microplastic, as these output a particle number. In Germany, compost is a potential vector for MP in soil due to its use as fertilizer. Therefore, we show the application of TThermoExtractionDesorption-GasChromatography-MassSpectrometry (TED-GC-MS) as a fast, integral analytical technique, which in contrast to the spectroscopic methods does not measure the number of particles but a mass content. In a nitrogen atmosphere the sample is pyrolyzed to 600 °C and an excerpt of the pyrolysis gases is collected on a solid phase adsorber. Afterwards, the decomposition gases are desorbed and measured in a GC-MS system. Characteristic pyrolysis products of each polymer can be used to identify the polymer type and determine the mass contents in the present sample. For the first time the work represents a routine procedure for the determination of plastics in composts and fermentation residues. This current study will also give inside in various important aspects of sample preparation, which include a meaningful size fractionation, a necessary density separation regarding the removal of inorganic contents and at finally a homogenization. T2 - SETAC Copenhagen – SETAC Europe 32nd Annual Meeting CY - Copenhagen, Denmark DA - 15.05.2022 KW - Microplastics KW - Soil KW - Pathway KW - Detection PY - 2022 AN - OPUS4-56293 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ciornii, Dmitri T1 - Identification of toxicologically relevant functional groups on micro- and nanoplastic particles’ surface by means of X-Ray photoelectron spectroscopy N2 - Microplastic and nanoplastic particles (MNP) are spread all over the world in various types, shapes and sizes making it very challenging to accurately analyse them. Each sampling procedure, sample preparation method and detection technique needs suitable reference materials to validate the method for accurate results. Furthermore, the effects of these MNPs should be evaluated by risk and hazard assessment with test particles close to reality. To better understand MNP behavior and aid in clarification of their interactions with organisms, we produced several MNP materials by top-down procedure and characterized their properties. Since surface properties mostly determine particles’ toxicity, the aim of the present study was to determine which functional groups are present on MNPs and how the surface can be affected by the production process and particle’s environment. T2 - SETAC 34th Meeting CY - Seville, Spain DA - 05.05.2024 KW - Microplastics KW - Nanoplastics KW - Polypropylene KW - XPS KW - SEM PY - 2024 AN - OPUS4-60037 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Realitätsnahe Referenzmaterialien für die Mikroplastik-Analytik und Vergleichsuntersuchungen N2 - Zur Validierung und Harmonisierung von verschiedenen Methoden in der Mikroplastik-Analytik werden polymere Referenzmaterialien benötigt. In diesem Vortrag wird dargestellt, was bisher an der BAM zu Referenzmaterialien für die Mikroplastik-Analytik entwickelt wurde, wo es hingehen soll und ein Überblick über bisher gelaufene Vergleichsuntersuchungen gebracht. T2 - Kick-off Meeting "Mikroplastik in Lebensmitteln" CY - Online meeting DA - 03.12.2020 KW - Mikroplastik KW - Referenzmaterial KW - Vergleichsuntersuchungen KW - Ringversuche PY - 2020 AN - OPUS4-51743 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Schroeder, Barbara T1 - Selektive und irreversible Immobilisierung von Antikörpern N2 - Das Ziel dieser Arbeit war es, die Vernetzung (Crosslinking) zwischen Protein G und einem Antikörper so durchzuführen, dass es zu keiner Modifikation der Antigen-Bindungsstelle des Antikörpers kommt. Zudem wurde im Rahmen dieser Arbeit ein Immunoassay entwickelt, mithilfe dessen zwanzig verschiedene Crosslinker in Hinblick auf ihre Fähigkeit Protein G zu funktionalisieren, untersucht werden konnten. Es konnten fünf Reagenzien identifiziert werden, die eine Derivatisierung von Protein G sowie eine anschließende Immobilisierung des Antikörpers auf dem Protein ermöglichen. Des Weiteren wurde gezeigt, dass mithilfe dieses Verfahrens sowohl die Immunpräzipitation als auch die massenspektrometrische Identifizierung und Charakterisierung von Proteinkomplexen erleichtert und verbessert werden kann. KW - Antikörper KW - Orientierte Immobilisierung KW - Protein A KW - Protein G KW - Linker KW - Crosslinker KW - IgG KW - Immunglobulin KW - Glutaraldehyd KW - 1,3-Butadiendiepoxid KW - NHS-Iodacetamid-Crosslinker SIAB KW - Succinimidyl(4-iodacetyl)aminobenzoat (SIAB) KW - Sulfo-SIAB KW - SIAB KW - SIA KW - SBAP PY - 2017 SP - 1 EP - 172 PB - Humboldt-Universität zu Berlin CY - Berlin AN - OPUS4-54537 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Liu, F. A1 - Reinmuth-Selzle, K. A1 - Lai, S. A1 - Weller, Michael G. A1 - Pöschl, U. A1 - Kampf, C. J. T1 - Simultaneous determination of nitrated and oligomerized proteins by size exclusion high-performance liquid chromatography coupled to photodiode array detection N2 - Chemical modifications such as nitration and cross-linking may enhance the allergenic potential of proteins. The kinetics and mechanisms of the underlying chemical processes, however, are not yet well understood. Here, we present a size-exclusion chromatography/spectrophotometry method (SEC-HPLC-DAD) that allows a simultaneous detection of mono-, di-, tri-, and higher protein oligomers, as well as their individual nitration degrees (NDs). The ND results of proteins from this new method agree well with the results from an alternative well-established method, for the analysis of tetranitromethane (TNM)- and nitrogen dioxide and ozone (NO2/O3)-nitrated protein samples. Importantly, the NDs for individual oligomer fractions can be obtained from the new method, and also, we provide a proof of principle for the calculation of the concentrations for individual protein oligomer fractions by their determined NDs, which will facilitate the investigation of the kinetics and mechanism for protein tyrosine nitration and cross-linking. KW - Size exclusion chromatography KW - HPLC-DAD KW - Protein nitration degree KW - Protein oligomer analysis KW - Nitrotyrosine KW - Dimer KW - Trimer KW - Oligomer KW - Protein KW - Tetranitromethane KW - BSA KW - Albumin KW - Air pollution KW - Nitrogen oxides PY - 2017 UR - http://www.sciencedirect.com/science/article/pii/S0021967317303795 DO - https://doi.org/10.1016/j.chroma.2017.03.015 SN - 0021-9673 VL - 1495 SP - 76 EP - 82 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-40304 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weller, Michael G. T1 - Trennschärfe: Robustheit, Selektivität und Spezifität N2 - Zusammenfassung Selektivität 1. Widersprüchliche Definitionen in unterschiedlichen Bereichen 2. Analytische Definition (pragmatisch): Selektivität ist die Fähigkeit einer Methode zur Unterscheidung aller interessierender Stoffe in der Probe. 3. Tests: Blindwerte, Leerwerte, Blank Values; Peakform 4. Wichtige Einflussgrößen: Trennleistung, Auflösung, Peakkapazität, Trennkapazität 5. Verbesserung durch: Kopplungsverfahren, Änderung der chromatographischen „Selektivität“, Orthogonalität 6. Wichtig ist auch die Komplexität der Probe(n) 7. Selektivität in der Immunchemie/Biochemie wird oft als Kreuzreaktion gemessen. Zusammenfassung Robustheit 1. Sehr individuelle Kriterien – sinnvolle Auswahl notwendig! 2. Wichtige Testphasen: a)Änderung von Methodenparametern b)Stabilität über die Zeit c)Überführung in die Routine 3. Ringversuche bzw. Laborvergleichsmessungen 4. Wichtigstes Vergleichskriterium: Relative Verfahrensstandardabweichung 5. Extratipp: Maximale Diversität der Testproben sicherstellen (besonders bezüglich der Matrix) T2 - BAM Sommerschule 2016 "Qualitätssicherung in der analytischen Chemie" CY - Berlin, Germany DA - 04.07.2016 KW - Selektivität KW - Spezifität KW - Robustheit KW - Sommerschule KW - Blindwert KW - Peakkapazität KW - Kreuzreaktion PY - 2016 AN - OPUS4-37760 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Canning, S. A1 - Voskuil, J. A1 - Weller, Michael G. T1 - An author and reviewer in conversation – reproducibility and antibody validation N2 - A recent Opinion Article by Jan Voskuil (JV), Aeonian Biotech, discussed the challenges in validation of research antibodies. It was openly peer reviewed by Michael Weller (MW), Federal Institute for Materials Research and Testing (BAM), Germany. In this blog, both discuss these challenges, the reproducibility crisis and open data. DA - 19 May, 2017 KW - Antibodies KW - Monoclonal KW - Antibody ID KW - Quality control KW - Open data KW - Reproducibility KW - Peer review PY - 2017 UR - https://blog.f1000.com/2017/05/19/an-author-and-reviewer-in-conversation-reproducibility-and-antibody-validation SN - 2051-9796 SP - 1 EP - 5 PB - F1000 Research Ltd. CY - London AN - OPUS4-40310 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Abbas, Ioana M. T1 - HPLC-MS/MS quantification of hepcidin-25, a new promising iron biomarker, in human serum samples N2 - Hepcidin-25 has attracted much attention ever since its discovery in 2001. It is widely recognized that this liver produced peptide hormone plays a major role in the regulation of iron levels in mammals. Hepcidin levels could reveal important clinical information about several pathological states in patients suffering from iron-related disorders such as chronic kidney disease (CKD) or hereditary haemochromatosis (HH). Despite significant efforts though, the development of a reliable assay to quantify hepcidin proved to be problematic for the last 15 years. With the aim to tackle the current difficulties in hepcidin quantification and improve the status of this promising biomarker in the clinical field, we developed a rapid and robust analytical strategy for the quantification of hepcidin-25 in human samples based on HPLC-MS/MS (QqQ) to be implemented in routine laboratories. The novelty of the method is the use of special HPLC vials to avoid adsorptive losses due to the basic character of the peptide that causes interaction with the silanol groups of the vial’s glass surface. Up to 90% decrease in the MS/MS signal was observed, when commercial HPLC vials were used, while vials treated with 3-(2-aminoethylamino)propylmethyl-dimethoxysilane or 1H,1H,2H,2H-perfluorooctyltriethoxysilane, leading to no significant losses in the dynamic range of physiological hepcidin-25 mean serum levels (10-20 µg/L). Careful analytical validation was performed for determining the reproducibility, repeatability, limit of quantification (0.5 µg/L) and linearity (0.5-40 µg/L) of the method. Serum samples from 9 healthy volunteers were analyzed with a median hepcidin-25 level of 3.3 µg/L, comparable to results reported in the literature. T2 - Tag der Chemie 2017 CY - Berlin, Germany DA - 05.07.2017 KW - Hepcidin-25 KW - LC-MS/MS KW - Iron biomarker PY - 2017 AN - OPUS4-41193 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schwaar, Timm T1 - Particle-based epitope analysis of a monoclonal antibody N2 - A method for the examination of the epitope of a monoclonal antibody against a peptide related to hepcidin-25, known as a biomarker in the ion metabolism, was developed. Characterizing the exact binding site helps to understand the properties of the antibody. A peptide consists of different amino acids, each contributing differently to the binding strength. To examine the influence of the amino acids, each amino acid was subsequently exchanged by glycine. If the respective amino acid is critical for binding to the antibody, a significant drop in the binding affinity should be observed. The epitope screening of monoclonal antibodies is a complex and elaborate procedure. For this approach, variants of the peptides were synthesized by conventional Fmoc-based peptide synthesis. The solid support was chosen to be suitable for the synthesis and additional screening against the antibody. To determine the binding affinity, the bead-bound peptides were incubated with a fluorophore-labeled antibody. After the incubation, the beads were placed on a slide and the fluorescence was detected by a fluorescence scanner. A high fluorescence indicates a high binding affinity and vice versa. T2 - Tag der Chemie 2017 CY - Berlin, Germany DA - 05.07.2017 KW - Antibody KW - Epitope analysis PY - 2017 AN - OPUS4-41191 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Paul, Martin T1 - Microarrays for the screening of monoclonal antibodies from supernatants N2 - In this thesis a protocol based on a direct competitive and non-competitive immunoassay using the microarray format was developed to screen emulated hybridoma supernatants against the drug carbamazepine (CBZ). As support, epoxy slides were manufactured by coating microscope glass slides with epoxy silanes. The manufactured epoxy slides showed similar capacity for protein immobilization as commercially available NEXTERION slides, but showed a higher autofluorescence background. On the epoxy slides, protein A, Cys-A, G and Cys-G were immobilized as antibody capturing coating. It could be shown that the Cys-tag considerably increased the immobilization of all compared proteins, especially of protein G. Protein Cys-G immobilized at pH 8-9 was considered the most suitable protein for antibody immobilization due to good spot uniformity and a high binding capacity for IgG. Additionally, in immobilization experiments it could be shown, that 10-500 fold excess of bovine IgG, introduced by two different fetal bovine serum (FBS) products, showed no significant competition on the immobilization of mice or goat IgG on protein Cys-G. To examine the captured antibodies for affinity to CBZ, the CBZ-TOTA-DY654 tracer was custom synthesized. It could be demonstrated, that the tracer antibody interaction was competitive with the tracer precursor, CBZ-TOTA-NH2 and CBZ. Furthermore, the synthesized tracer was also successfully used by externals to evaluate CBZ affine hybriodoma cells in flow cytometry. In the simulated screening, five antibodies with known affinity to CBZ were diluted in a cell culture medium. The screening method allowed to differentiate between affine antibodies (IC50 < 20 µg/ml) and unaffine antibodies (IC50 > 20 µg/ml), when concentrations of 0.1 µg/ml IgG or greater have been used. Of five applied antibodies, all highly affine clones (CE2 and B3212M) were reported as positives while no false-positive samples were observed. The screening included competitive, with around 89500 fold excess of CBZ, and non-competitive tracer incubation on different segments of the same chip, which resulted in total signal suppression on the competitive segment. The screening was performed in 20 hours, only a few nanoliters, of each simulated supernatant, were consumed in the screening process, furthermore in the method standard 96 well MTPs were used and no cleanroom facilities were required. KW - Carbamazepine KW - Microscopic slides KW - Protein A cys KW - Competition KW - Epoxy silanes KW - Supernatant KW - Antibody immobilization PY - 2017 SP - 1 EP - 96 PB - Humboldt-Universität zu Berlin CY - Berlin AN - OPUS4-54645 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Völzke, Jule Lexa T1 - Herstellung und Charakterisierung Antigen-beschichteter Nanopartikel als Analoga von Virus-like Particles (VLP) N2 - In dieser Arbeit wurden drei verschiedene Nanomaterialien auf ihre Bindungsfähigkeit zu Proteinen untersucht. Zu Beginn standen dabei die Herstellung stabiler Dispersionen der einzelnen Nanopartikel und die Stabilität der gebildeten Konjugate im Vordergrund. Der Nachweis einer erfolgreichen Konjugatbildung, sprich der Beschichtung von Nanopartikel mit Proteinen, wurde sowohl qualitativ mittels DLS-Messungen als auch über quantitative Protein-Bestimmungen erbracht. Für die Quantifizierung konnten verschiedene Methoden eingesetzt werden. Neben der klassischen Vorgehensweise, welche indirekt über die Quantifizierung von ungebundenem Protein im Überstand erfolgt, konnten ihm Rahmen dieser Arbeit verschiedene direkte Bestimmungsmethoden entwickelt werden. So wurden mittels kolorimetrischer Tests, wie dem BCA-Assay und dem Bradford-Assay, Nanodiamantdispersionen mit Hilfe einer Korrekturwellenlänge vermessen und quantifiziert. Ebenso zum Einsatz kam die Methode der Aminosäureanalytik, welche aufgrund ihrer guten Rückführbarkeit auf Aminosäurestandards Ergebnisse mit hoher Richtigkeit generieren kann und ebenso die Detektion kleiner Proteinmengen möglich macht. Nach den erfolgten quantitativen Betrachtungen wurden die Protein-beschichteten Nanopartikel auf ihre Anwendbarkeit als Analoga von Virus-like Particles (VLP) bei einer Immunisierung zur Gewinnung von polyklonalen Antikörpern gegen humanes Ceruloplasmin in Kaninchen überprüft. Es konnte mittels ELISA gezeigt werden, dass die Konjugate erfolgreich für die Herstellung von Antikörpern eingesetzt werden können und im zeitlichen Verlauf einer Immunisierung eine Steigerung des Antikörper-Titers zu erreichen ist. KW - DLS KW - Dynamische Lichtstreuung KW - Aluminiumoxid KW - Nanodiamant KW - Gold-Nanopartikel KW - BSA KW - Albumin KW - Protein G KW - Ceruloplasmin KW - Immunpräzipitation KW - Ultraschall KW - BCA KW - Bradford-Assay KW - AAAA KW - Aromatische Aminosäureanalytik KW - ICP-MS KW - NaCl-Methode PY - 2018 SP - 1 EP - 107 PB - Humboldt-Universität zu Berlin CY - Berlin AN - OPUS4-54625 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Taube, Peter T1 - Development of columns based on glass monoliths for affinity chromatography N2 - The aim of this work was the preparation of a novel stationary monolithic phase for affinity chromatography and HPLC-applications. Therefore, we have chosen porous glass filters that are available with different pore sizes as raw materials to prepare monolithic columns. We purchased VitraPOR 4 (10-16 μm pore size) and VitraPOR 5 (1.0-1.6 μm pore size) monolithic glass filters. The physical properties of these glass filters were characterized. The surface area, pore size distribution and the porosity were determined using mercury intrusion porosimetry and BET. These glass filters only exhibit flow through pores and therefore show no bimodal pore size distribution in the mercury intrusion curves. Due to their low permeability, the applied filters that exhibit an inner diameter of 8.0 mm and a length of 15.0±0.1 mm could be operated at flow rates more than 10 ml/min. High flow rates are favorable for fast separation experiments. KW - Monolith KW - Affinity chromatography KW - Affinity extraction KW - Borosilicate glass KW - Sintered KW - Surface area KW - Flow rate KW - VitraPOR KW - Pressure KW - Protein A KW - Dynamic binding capacity KW - Protein A cys KW - Column regeneration KW - Performance comparison PY - 2017 SP - 1 EP - 102 PB - Humboldt-Universität zu Berlin CY - Berlin AN - OPUS4-54564 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Gabler, Mariella T1 - Development of an affinity-based method for the site-selective synthesis of antibody-drug-conjugates N2 - For the site-selective synthesis of ADCs, a variety of obstacles must be overcome. Those include designing bifunctional affinity peptides with reasonably low 𝐾𝑑-values that couple to the mAb in a site-selective manner. These peptides should also include a functional group that links the payload to the mAb under mild conditions without adversely affecting it. The bioconjugation between peptide and antibody and the linker between peptide and payload must be stable and durable to provide safety when used for medical purposes. The usage of metals and organic solvents should be minimized. Within the project, new types of functionalized affinity peptides were designed, and their affinity towards the Fc-fragment was determined. KW - Antibody drug conjugate KW - ADC KW - Human antibody KW - Peptide KW - Linker KW - Toxin KW - Payload KW - Monomethyl Auristatin E KW - MMAE KW - DM1 KW - Click chemistry KW - Copper-catalyzed KW - SDS-PAGE KW - HPLC KW - Trastuzumab KW - Herceptin KW - SPR KW - MALDI-TOF-MS KW - Mertansine KW - Site-selective bioconjugation KW - Affinity PY - 2021 SP - 1 EP - 100 PB - Humboldt-Universität zu Berlin CY - Berlin AN - OPUS4-54519 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Weller, Michael G. A1 - Schneider, Rudolf A1 - Rurack, Knut T1 - Mit dem Testsystem zur Probe N2 - (Bio)chemische Sensoren ersetzen bei der Vor-Ort-Analytik die großen Messgeräte oder dienen dazu, Analyten im Verdachtsfall oder kontinuierlich zu überwachen. Das können pharmazeutische Stoffe im Abwasser sein, Aflatoxin in Milch oder Sprengstoff am Flughafen. Ein Überblick über Neuentwicklungen. KW - Biochemische Sensoren KW - Vor-Ort-Analytik KW - Schnelltests KW - Antikörper PY - 2021 DO - https://doi.org/10.1002/nadc.20214112170 VL - 69 IS - 10 SP - 71 EP - 74 PB - Wiley-VCH CY - Weinheim AN - OPUS4-54003 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Paul, Martin T1 - Development of a high-sensitivity biosensor for the quasi-continuous detection of the explosive TNT and the illegal drug cocaine N2 - An immunofluorometric biosensor with laser-induced fluorescence detection was presented. For TNT an LOD of 60 ppb and for cocaine an LOD of 9 ppb was achieved. A swipe test was performed in less than 3 minutes. No significant cross-reactivity was observed. T2 - 15. Interdisziplinäres Doktorandenseminar des Arbeitskreises Prozessanalytik der GDCh CY - Online meeting DA - 06.09.2021 KW - PETN KW - HMX KW - RDX KW - Microfluidic mixing KW - Lab-on-a-chip KW - Affinity column KW - Monolithic material KW - Sintered glass KW - Dy-654 KW - Flowcell KW - Epifluorescence KW - CMOS camera KW - Diode laser KW - Antibody screening PY - 2021 AN - OPUS4-53329 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tannenberg, Robert T1 - Detection of Cardiac Troponin I with Chemiluminescence Biosensor N2 - Cardiovascular diseases are the number one cause of death worldwide and responsible for 3.9 million deaths in Europe and over 1.8 million deaths in the European Union (2017) [1]. Cardiac Troponin I (cTnI) is part of a triple protein complex and the most important biomarker for acute events such as heart attacks. Once a heart attack occurs, the blood stream within the heart is interrupted and further oxygen supply cannot be maintained. As a result, heart cells undergo apoptosis and their proteins will be released into the blood stream. Within the project CardioMet of the European Metrology Program of Research and Innovation (EMPIR) a biosensor for online-monitoring of acute myocardial infarction by detecting cTnI is being developed. T2 - SALSA Make and Measure 2021 CY - Online meeting DA - 16.09.2021 KW - Sensor KW - Luminol KW - ECL KW - Peroxidase KW - Monolith KW - Lab on a Chip KW - EMPIR KW - 18HTL10 KW - CardioMet KW - Horizon 2020 PY - 2021 AN - OPUS4-53306 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Becker, Roland A1 - Altmann, Korinna A1 - Sommerfeld, Thomas A1 - Braun, Ulrike T1 - Quantification of microplastics in a freshwater suspended organic matter using different thermoanalytical methods – outcome of an interlaboratory comparison N2 - A sedimented freshwater suspended organic matter fortified with particles of polyethylene (PE), polypropylene (PP), polystyrene (PS), and polyethylene terephthalate (PET) was employed in an interlaboratory comparison of thermoanalytical methods for microplastics identification and quantification. Three laboratories performed pyrolysis gas chromatography-mass spectrometry (Py-GC-MS), three others provided results using thermal extraction desorption followed by gas chromatography coupled to mass spectrometry (TED-GC-MS). One participant performed thermogravimetry-infrared spectroscopy (TGA-FTIR) and two participants used thermogravimetry coupled to mass spectrometry (TGA-MS). Further participants used differential scanning microscopy (DSC), a procedure based on micro combustion calorimetry (MCC) and a procedure based on elemental analysis. Each participant employed a different combination of sample treatment, calibration and instrumental Settings for polymer identification and quantification. Though there is obviously room for improvements regarding the between-laboratory reproducibility and the harmonization of procedures it was seen that the participants Performing Py-GC-MS, TED-GC-MS, and TGA-FTIR were able to correctly identify all polymers and to report reasonable quantification results in the investigated concentration range (PE: 20.0 μg/mg, PP: 5.70 μg/mg; PS: 2.20 μg/mg, PET: 18.0 μg/mg). Although for the other methods limitations exists regarding the detection of specific polymers, they showed potential as alternative approaches for polymer quantification in solid environmental matrices. KW - Interlaboratory comparison KW - Microplastics KW - Suspended organic matter KW - Pyrolysis PY - 2020 DO - https://doi.org/10.1016/j.jaap.2020.104829 VL - 148 SP - 1 EP - 6 PB - Elsevier B.V. AN - OPUS4-50977 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Monikh, Fazel A. A1 - Materić, Dušan A1 - Valsami-Jones, Eugenia A1 - Grossart, Hans-Peter A1 - Altmann, Korinna A1 - Holzinger, Rupert A1 - Lynch, Iseult A1 - Stubenrauch, Jessica A1 - Peijnenburg, Willie T1 - Challenges in studying microplastics in human brain N2 - Human exposure to microplastics and nanoplastics (MNPs) is an emerging concern with potential implications for health. As awareness of this issue grows, it has prompted increasing scientific attention toward understanding if, and how, MNPs accumulate in human tissues. In a recent study, Nihart et al.1 used the analytical technique of pyrolysis gas chromatography–mass spectrometry (Py-GC–MS) to detect MNPs in human liver, kidney and brain, reporting the highest concentrations in the brain, with polyethylene as the predominant polymer. The study as reported appears to face methodological challenges, such as limited contamination controls and lack of validation steps, which May affect the reliability of the reported concentrations. In this Matters Arising, we highlight methodological limitations that have General relevance for advancing robust and reproducible MNP detection in human biomonitoring studies. KW - Microplastics KW - Nanoplastics KW - Py-GC-MS PY - 2025 DO - https://doi.org/10.1038/s41591-025-04045-3 SN - 1078-8956 VL - 31 IS - 12 SP - 1 EP - 3 PB - Springer Science and Business Media LLC AN - OPUS4-64698 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Seasonal microplastic concentrations along the rivers Rhine and Danube N2 - Over the last 20 years, many researchers, politicians and citizens have become increasingly aware of the growing plastic problem of our time. A lack of recycling concepts and plastic collection points as well as careless dumping lead to accumulation of plastic products in the environment. Natural weathering can cause these plastics to degrade and fractionate, meaning that microplastics (1 1,000 µm, ISO/TR 21960:2020) and nanoplastics (< 1 µm, ISO/TR 21960:2020) of various synthetic polymer materials can now be detected in all parts of the world. Whether microplastics or nanoplastics pose a toxicological hazard is being investigated in a variety of ways. Valid results are still pending. However, the EU precautionary principle applies to micro- and nanoplastics. Monitoring of microplastics is already required in the revision of the Drinking Water and Wastewater Framework Directive. Reliable monitoring of rivers can be carried out by sampling with sedimentation boxes and microplastic detection by using thermal extraction desorption gas chromatography/mass spectrometry (TED-GC/MS) in routine operation (Figure 1). The river Rhine was sampled for microplastic masses at three different sampling locations over a period of one year and in addition the Danube at randomized sampling locations The TED-GC/MS results showed that various synthetic polymers frequently produced in industry, such as polyethylene, polypropylene or polystyrene as well as the tire compound styrene-butadiene rubber were found. The work not only shows a possible workflow for monitoring concepts, but also provides information on environmentally relevant concentrations of microplastics and tire components in surface waters. This in turn is necessary for ecotoxicological studies. T2 - ESOPS CY - Berlin, Germany DA - 09.09.2024 KW - Microplastics KW - TED-GC/MS KW - Polymer 3R PY - 2024 AN - OPUS4-61016 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Atanasova, Aleksandra T1 - Herstellung und Einsatz neuartiger Trypsin-Partikel für den enzymatischen Antikörper-Verdau N2 - In dieser Arbeit wurden zwei Trypsinvarianten, der Wildtyp (wtT) und eine thermostabile Variante (tsT), rekombinant hergestellt. Die Herstellung von Proteinen in Bakterien kann zu Fehlfaltungen und Einschlusskörperchen führen, weshalb eine geeignete Faltungsstrategie notwendig ist. In dieser Arbeit konnte eine schrittweise Vorgehensweise erfolgreich angewendet werden. Nach der Ni-NTA-Aufreinigung wurde zusätzlich eine substratspezifische Benzamidin-Aufreinigung eingesetzt, um die Aktivität zu verbessern. Außerdem wurden die rekombinanten Trypsine auf Korund immobilisiert. Korund ist ein kostengünstiges Material, das nach Silanisierung und Glutaraldehyd-Kopplung für die Bindung von Proteinen geeignet gemacht wurde. Dabei konnte gezeigt werden, dass mehr wtT als tsT gebunden wurde, was sich auch in den Kopplungsdichte widerspiegelte. Die immobilisierten Enzyme wurden in Bezug auf Aktivität, Wiederverwendbarkeit, Lagerfähigkeit und Temperaturstabilität untersucht. Beide Varianten zeigten vergleichbare Leistungen, wobei tsT bei höheren Temperaturen eine etwas bessere Stabilität aufwies. Für den Antikörperverdau wurden sowohl thermische als auch chemische Denaturierungen bei verschiedenen Temperaturen ( 37 °C und 60 °C) getestet. Die Analyse mit MALDI-TOF-MS zeigte, dass gute Werte für die Sequenzabdeckung erzielt werden konnten. Besonders die chemische Denaturierung führte zu besseren Ergebnissen mit weniger Selbstverdau. Beim Vergleich mit kommerziell immobilisiertem Crude-Trypsin zeigten die rekombinanten Varianten eine höhere Spezifität und bessere Sequenzabdeckung bei gleichzeitig geringerem Selbstverdau. Die Wiederverwendbarkeit wurde durch fünf Verdauzyklen bei 37 °C überprüft. Dabei blieb die Aktivität weitgehend stabil, auch wenn die Peakintensität in den MALDI-Spektren mit jedem Zyklus abnahm. Eine eindeutige Zuordnung der Fingerprints des Antikörpers aus einer Bibliothek von über 90 Antikörpern war trotz dessen gegeben. KW - Korund KW - Immobilisierung KW - Proteomik KW - Rekombinante Proteine KW - Thermostabile Enzyme PY - 2025 SP - 1 EP - 86 CY - Berlin AN - OPUS4-64433 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kittner, Maria A1 - Bauer, Vanessa A1 - Altmann, Korinna A1 - Kraft, Oliver A1 - Nordmann, Thomas A1 - Kalbe, Ute T1 - Mikroplastik-Austrage aus Kunststoffrasenplatzen ins Grundwasser N2 - Sportplätze aus Kunststoffrasen haben sich im Breitensport etabliert, weshalb ihre Anzahl jährlich zunimmt. Dabei werden Umwelt- und Gesundheitsrisiken, insbesondere durch Mikroplastik-Austräge, kontrovers diskutiert. Um die ungenügende Datenlage zur Menge des Austrages an Mikroplastik zu verbessern, haben sich zwei individuelle Studien mit dieser Forschungsfrage mit Fokus auf den Boden-Grundwasser-Pfad befasst, deren Ergebnisse hier erstmalig gemeinsam vorgestellt werden. Die erste Studie simulierte unter Laborbedingungen Mikroplastik-Emissionen von drei Kunststoffrasen-Szenarien in unterschiedlichen Alterungszuständen und analysierte thermoanalytisch. Die zweite Studie untersuchte Grundwasser-Proben von zwei Realsportplätzen, die 1 m unter dem Grundwasserspiegel entnommen und spektroskopisch untersucht wurden. Dies ermöglicht erstmalig einen Vergleich von Mikroplastik-Austrägen über das Sickerwasser in verschiedenen Bodentiefen. Die Labor-Ergebnisse ergaben je nach Alterungszustand des Kunststoffrasenplatzes Mikroplastik-Emissionen zwischen < 0,1 μg/L und 26,8 μg/L in 30 cm Bodentiefe. Wohingegen in den Grundwasser-Proben der Realsportplätze ab 4 m Bodentiefe keine Kunststoffrasen-Partikel detektiert wurden. Dies deutet darauf hin, dass vermehrt Mikroplastik durch Alterung aus Kunststoffrasen entsteht und im Sickerwasser ausgetragen wird, aber der Boden Mikroplastik- Partikel ≥ 5 μm durch Filtrationseffekte zurückhält, sodass diese im Grundwasser nicht nachweisbar waren. KW - Kunststoffrasen, Alterung, Mikroplastik, Elution, Schadstoffe PY - 2025 DO - https://doi.org/10.37307/j.1868-7741.2025.04.05 SN - 1868-7741 VL - 30 IS - 4 SP - 156 EP - 161 PB - Erich Schmidt Verlag GmbH & Co. KG AN - OPUS4-65098 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Welche Rolle spielen Textilien als Mikroplastik-Quelle im Abwasser? N2 - In diesem Vortrag wird die Rolle der Waschmaschine als Eintragspfad von Mikroplastik in das Abwasser diskutiert und eine experimentelle Annäherung an das Problem beschrieben. T2 - Wasserwirtschaftliches Kolloquium der TU Berlin CY - Berlin, Germany DA - 14.12.2023 KW - Mikroplastik KW - TED-GC/MS KW - Waschmaschine PY - 2023 AN - OPUS4-59278 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Systemverständnis und Untersuchungsstrategien von Kunststoffeinträgen in die Umwelt – Ergebnisse des RUSEKU-Forschungsprojektes N2 - Ziel des Vortrages ist die Vermittlung der Herausforderungen der Mikroplastik-Analytik sowie der Harmonisierung der Analytik und des Ergebnistransfers in die Normung. T2 - Jahresabschluss-Sitzung GA "Mensch und Umwelt" CY - Online meeting DA - 24.11.2021 KW - Mikroplastik KW - Mikroplastik-Analytik PY - 2021 AN - OPUS4-53830 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Update from ISO/TC 61/SC14/WG4 N2 - This talk is an update from ISO/TC 61/SC14/WG4. It describes the production of microplastic test material for the use in an interlaboratory comparison. IWe report the first results of an ILC on microplastic detection methods organized under the pre-stantdardisation plattform of VAMAS (www.vamas.org/twa45/) as Project 2 “Development of standardized methodologies for characterisation of microplastics with microscopy and spectroscopy methods”, within the Technical Working Area TWA 45 “Micro and Nano Plastics in the Environment”. The ILC has gathered 84 participants all over the world representing all continents. Reference materials were developed by BAM to test the main methods for MPs detection as addressed in ISO/TR 21960:2020: thermo-analytical methods (Py-GC/MS and TED-GC/MS) and vibrational methods (µ-IR and µ-Raman). As far as the mass fraction is concerned, accurate results with quite a good precision were achieved with the thermo-analytical methods. Number-based results are not adressed here. T2 - ISO/TC 147/SC 2/JWG CY - Online meeting DA - 03.06.2025 KW - Microplastics KW - ILC KW - Reference materials PY - 2025 AN - OPUS4-63340 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fünning, Tabea A1 - Peczek, Anna A1 - Kroh, Aleksandra A1 - Mai, Christian A1 - Paul, Martin A1 - Thomsen, Florian A1 - Tannenberg, Robert A1 - Schumann, Christoph A1 - Weller, Michael G. A1 - Mai, Andreas A1 - Steglich, Patrick C. ED - Lieberman, Robert A. ED - Baldini, Francesco ED - Homola, Jiri T1 - Optimization of local backside released micro-ring resonators for sensing applications using silicon photonic integrated circuits in a SOI technology N2 - Photonic micro-ring resonators (MRR) are widely studied for their high sensitivity across applications like environmental monitoring, healthcare, and chemical analysis. Their evanescent field sensing requires partially unembedded waveguides compatible with CMOS processing. Our approach uses local backside etching with an additional buried oxide (BOX) etch to release waveguides while preserving the back-end of line (BEOL) structure, enabling spatial separation of the sensing area and electronics. The BOX etch critically affects sensor performance, as waveguide surface roughness can alter MRR properties and coupling. We analyzed MRR design variations, comparing wet and dry etching techniques for their effects on optical performance across rib and strip waveguides in quasi-TE and quasi-TM modes. Wafer-level measurements show that backside-released MRR achieve high extinction ratios with slightly reduced quality factors, advancing high-sensitivity photonic sensors. T2 - SPIE Optics + Optoelectronics 2025 CY - Prague, Czech Republic DA - 23.05.2025 KW - Photonic sensors KW - Micro-ring resonator (MRR) KW - Silicon on insulator (SOI) KW - CMOS KW - Local backside etching PY - 2025 SN - 978-1-5106-8851-3 DO - https://doi.org/10.1117/12.3056481 VL - 13527 SP - 1 EP - 8 PB - SPIE CY - Bellingham, WA , USA AN - OPUS4-63585 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Steglich, Patrick A1 - Paul, Martin A1 - Fünning, Tabea A1 - Schumann, Christoph A1 - Mai, Christian A1 - Tannenberg, Robert A1 - Mai, Andreas ED - Cheben, Pavel ED - Čtyroký, Jiří ED - Molina-Fernández, Iñigo T1 - Towards monolithic integration of polymer-based electro-optical devices in silicon photonic integrated circuits using a 250nm SOI technology N2 - Photonic micro-ring resonators (MRR) are widely studied for their high sensitivity across applications like environmental monitoring, healthcare, and chemical analysis. Their evanescent field sensing requires partially unembedded waveguides compatible with CMOS processing. Our approach uses local backside etching with an additional buried oxide (BOX) etch to release waveguides while preserving the back-end of line (BEOL) structure, enabling spatial separation of the sensing area and electronics. The BOX etch critically affects sensor performance, as waveguide surface roughness can alter MRR properties and coupling. We analyzed MRR design variations, comparing wet and dry etching techniques for their effects on optical performance across rib and strip waveguides in quasi-TE and quasi-TM modes. Wafer-level measurements show that backside-released MRR achieve high extinction ratios with slightly reduced quality factors, advancing high-sensitivity photonic sensors. T2 - SPIE Optics + Optoelectronics 2025 CY - Prague, Czech Republic DA - 05.06.2025 KW - Photonic sensors KW - Micro-ring resonator (MRR) KW - Silicon on insulator (SOI) KW - CMOS KW - Local backside etching (LBE) PY - 2025 DO - https://doi.org/10.1117/12.3056280 VL - 13530 SP - 1 EP - 8 PB - SPIE CY - Bellingham, WA , USA AN - OPUS4-63587 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cakir, Cafer Tufan T1 - Algorithm-Assisted Multimodal Synchrotron Experiments: XRD–XES Integration and SpecTwin N2 - Multimodal synchrotron-based techniques are emerging as powerful tools for advanced materials characterization, enabling simultaneous insights into both crystal and electronic structure. We present a combined X-ray diffraction (XRD) and high-resolution X-ray emission spectroscopy (XES) approach implemented in a double-dispersive setup. This configuration enables simultaneous acquisition of structural and spectroscopic information with high precision, allowing us to resolve correlations between lattice arrangements and electronic configurations under in situ conditions. To enhance experimental throughput and reproducibility, we employ digital twin concepts and optimization algorithms for experiment design and parameter control. These methods effectively eliminate trial-and-error procedures when optimizing the setup to achieve the desired resolution for XES analysis. In addition, we introduce SpecTwin, a dedicated software environment that integrates XES data analysis, simulation, and optimization routines. This combined methodology underscores the potential of algorithm-assisted multimodal X-ray experiments to advance the quantitative understanding of structure–property relationships in complex materials. T2 - Joint BAM-HZB Symposium on Multimodal Synchrotron Experiments for Next-Generation Materials Research CY - Berlin, Germany DA - 25.02.2026 KW - XAS KW - Digital Twin KW - Optimization KW - Multimodal PY - 2026 AN - OPUS4-65608 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hejazi, Bardia T1 - X-ray Computed Tomography Image Compression and Denoising with AI N2 - The ever-growing volume of data in imaging sciences stemming from advancements in imaging technology, necessitates efficient and reliable storage solutions for such large datasets. In this study, we investigated the compression of industrial X-ray computed tomography (XCT) data using deep learning and examined how these compression algorithms affect the quality of the recovered data. To determine best strategies, we investigated two different network architectures with different compression rates. The XCT data used was from a sandstone sample with a complex internal pore network. The quality of the recovered images obtained from the two different deep learning architectures with different compression rates were quantified and compared to the original input data. We showed that the most suitable architecture and compression rate can change, depending on what specific characteristics we would need to preserve for later analysis. The findings presented here can aid scientists in determining the best approaches and strategies for their data storage and analysis requirements. T2 - BAM AI & ML Symposium CY - Berlin, Germany DA - 06.11.2025 KW - X-ray computed tomography KW - Compression KW - Deep Learning PY - 2025 AN - OPUS4-65610 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumann, Christoph T1 - Design and optimization of integrated multimode interferometers (MMIs) for dual-polarization photonic biosensors for biomedical applications in a silicon-on-insulator platform N2 - Faster, more sensitive, and cost-efficient diagnostic tests are crucial, as conventional lab tests are slow and expensive, while rapid tests often lack specificity. Advancements in medical diagnostics are crucial for early disease detection, reducing costs and testing time. Optical biosensors, particularly multimode interferometers (MMIs), offer high sensitivity and integration potential for Point-of-Care applications [1-2]. This work introduces a novel MMI biosensor utilizing orthogonal TE and TM modes, significantly minimizing the footprint. T2 - SPIE Optics + Optoelectronics 2025 CY - Prague, Czech Republic DA - 23.05.2025 KW - Interferometry KW - Semiconductor KW - Chip KW - Point-of-Care applications KW - Biomarker PY - 2025 UR - https://www.spiedigitallibrary.org/conference-proceedings-of-spie/PC13527/PC135270R/Design-and-optimization-of-integrated-multimode-interferometers-MMIs-for-dual/10.1117/12.3056490.short DO - https://doi.org/10.1117/12.3056490 AN - OPUS4-63568 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Döring, Sarah T1 - Surface Immobilization of Recombinant Trypsin onto Corundum Particles for Optimized Antibody Digestion N2 - Therapeutic monoclonal antibodies are the fastest-growing class of biological agents and the development of reliable analytical methods for their quantification is becoming increasingly important. Liquid chromatography coupled with tandem mass spectrometry (LC–MS/MS) represents one of the leading technologies for antibody quantification. The serin protease trypsin has emerged as the gold standard enzyme for digesting intact protein into peptides for this approach. However, many protocols exist that often lead to different results depending on the digestion procedure. In particular, the type and amounts of detergents added during sample preparation for protein unfolding before digestion is known to create undesirable structure modifications of proteins (e.g. carbamylation) and significant bias in measurement results by inhibiting enzyme activity. The source and nature of the enzyme itself can also have an influence, whereby immobilized variants are increasingly being used to improve their stability, minimize self-digestion and enable a higher substrate-enzyme ratio. Here, we explored the potential of a novel thermostable trypsin and surface-functionalised corundum particles for enhanced antibody digestion. For this purpose, the inactive zymogen was recombinantly produced in E. coli, activated with enterokinase digestion and finally affinity purified by benzamidine purification. The enzyme activity was analogous to commercially available MS-grade trypsin product. In addition, produced trypsin showed increased thermal stability under typical digestion conditions compared to reference product. Furthermore, APTES-silanization followed by glutaraldehyde modification of corundum surface with an additional blocking step prevents nonspecific protein adsorption during the protein digestion procedure and the immobilized enzyme still showed substrate activity after covalent binding. Compared to wild-type and a non-immobilized enzyme, the surface-functionalized thermostable variant showed increased activity at elevated temperatures. Thus, this novel type of trypsin particles promises to not only improve antibody digestion at high temperatures, but also to prevent self-digestion and enable the separation of trypsin from target peptides in LC–MS analysis. T2 - ANAKON 2025 CY - Leipzig, Germany DA - 10.03.2025 KW - Antibody Quantification KW - Corundum KW - Enzyme Immobilization KW - LC-MS/MS PY - 2025 AN - OPUS4-63480 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tannenberg, Robert T1 - Troponin I Assay in Wafer-Level Backside Optofluidics N2 - Cardiovascular diseases are the number one cause of death worldwide and responsible for 17.9 million casualities worldwide in 2019. Cardiac Troponin I (cTnI) is the most important biomarker for acute events such as heart attacks. The development of novel photonic integrated microchips (PIC) is a promising approach to allow the convenient detection of key biomarkers in complex matrices through multichannel real-time analysis in a highly compact package. This study presents the development and proof-of-concept of a backside released CMOS chip designed for the multichannel real-time detection of biomarkers. In this work, we introduce a Troponin I assay as well that utilizes a potential and practical approach to backside optofluidics on a wafer-level platform. T2 - Biosensors 2025 - 35th Anniversary World Congress on Biosensors CY - Lisbon, Portugal DA - 19.05.2025 KW - Ring resonator KW - Semiconductor KW - CMOS KW - cTnI KW - Heart attack KW - Biomarker KW - Sandwich immunoassay PY - 2025 AN - OPUS4-63481 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tannenberg, Robert T1 - Multichannel real-time detection of biomarkers with highly miniaturized photonic microchips N2 - The development of novel photonic microchips is a promising approach to advance the detection of biomarkers through multichannel real-time analysis. This study reports the successful development of a backside released CMOS chip designed for the multichannel real-time detection of biomarkers. Operating at a wavelength of 1550 nm, the microchip features three detection channels in addition to a reference channel, enabling simultaneous analysis of multiple biomarkers. The microchip incorporates micro-ring resonators that are directly functionalized with specific bioreceptors, which significantly improves the affinity towards target biomarkers. The employed surface functionalization strategy enables versatile immobilization of receptor molecules and serves as a starting point for various analytical applications. A tunable laser is utilized as the excitation source, providing precise wavelength tuning and stable optical output, essential for achieving optimal resonance conditions within the micro-ring resonators. Our chips use integrated multi-mode interferometers as beam-splitter, grating coupler and Ge-photodiodes, resulting in an ultra-small footprint. The complete chip including metal pads has an area of 1 mm2. The results indicate that the developed multichannel photonic microchip system enables online detection of multiple biomarkers. The compact and highly miniaturized design of this microchip positions them as promising candidates for point-of-care diagnostics and personalized medicine applications. With further advancements, this technology opens a path to transform biomarker detection across various medical fields, offering rapid, reliable, and cost-effective diagnostic solutions. In conclusion, the presented multichannel photonic microchips signify a substantial leap forward in real-time biomarker detection, providing a robust platform for future research and clinical applications. T2 - SPIE Optics + Optoelectronics 2025 CY - Prague, Czech Republic DA - 07.04.2025 KW - Biosensor KW - Optics KW - Silicon semiconductor KW - Proteins KW - Clinical chemistry PY - 2025 AN - OPUS4-62954 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Döring, Sarah T1 - Optimization of Polymer Interface: Novel Surface-functionalized Corundum Particles for Improved Antibody Digestion N2 - Therapeutic monoclonal antibodies are the fastest-growing class of biological agents and the development of reliable analytical methods for their quantification is becoming increasingly important. Liquid chromatography coupled with tandem mass spectrometry (LC–MS/MS) represents one of the leading technologies for antibody quantification. The serin protease trypsin has emerged as the gold standard enzyme for digesting intact protein into peptides for this approach. However, many protocols exist that often lead to different results. The talk will provide a brief introduction to the application of novel thermostable and surface-functionalized trypsin particles for improved antibody digestion as well as initial successes in polymer functionalization of the corundum surface to prevent nonspecific protein adsorption during the digestion procedure. T2 - SALSA Make and Measure 2024: Interfaces CY - Berlin, Germany DA - 11.09.2024 KW - Antibody Quantification KW - Recombinant Enzymes KW - LC-MS/MS KW - Enzyme Immobilisation KW - Surface Functionalisation KW - Corundum PY - 2024 AN - OPUS4-61041 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lohrke, Heiko A1 - Kohlhoff, Harald A1 - Erdmann, Jessica A1 - Winkler, Nicolas P. A1 - Neumann, Patrick P. T1 - Combined GNSS/Visual Inter-Robot Tracking Method for Open-Path Gas Tomography N2 - Methane emissions are a significant environmental and safety concern, yet many gas tomography systems intended to measure them require manual alignment, reliable high-bandwidth links, or fiducials. We present a lightweight, fully autonomous framework enabling line-of-sight inter-robot Tunable Diode Laser Absorption Spectroscopy (TDLAS) measurements without such constraints. A sensor robot equipped with a gimbal-mounted TDLAS unit tracks a reflector robot bearing an illuminated, color-controllable target. Coarse localization is achieved via RTK-GNSS, with vision-based fine tracking and passive time synchronization handled onboard. The system, based on off-the-shelf Pixhawk controllers and ArduPilot firmware, was validated in a 15m × 7m outdoor trial. Despite GNSS inaccuracies and deliberate occlusion by a methane-filled bag, the system retained lock, recovered from visual loss in under one second, and captured a 2800 ppm·m plume signature. These results demonstrate robust, scalable methane sensing for mobile gas tomography or standalone leak detection. Core components are released open-source to support future deployment. T2 - IEEE SENSORS 2025 CY - Vancouver, BC, Kanada DA - 19.10.2025 KW - Gas tomography KW - Tracking KW - Robot KW - Methane KW - TDLAS PY - 2025 SN - 979-8-3315-4467-6 DO - https://doi.org/10.1109/SENSORS59705.2025.11330519 SP - 1 EP - 4 PB - IEEE CY - Piscataway, NJ, USA AN - OPUS4-65615 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Karafiludis, Stephanos A1 - de Oliveira Guilherme Buzanich, Ana A1 - Kochovski, Z. A1 - Feldmann, Ines A1 - Emmerling, Franziska A1 - Stawski, Tomasz T1 - Ni- and Co-Struvites: Revealing Crystallization Mechanisms and Crystal Engineering toward Applicational Use of Transition Metal Phosphates N2 - Industrial and agricultural waste streams (waste water, sludges, tailings, etc.) which contain high concentrations of NH4+, PO43–, and transition metals are environmentally harmful and toxic pollutants. At the same time, phosphorous and transition metals constitute highly valuable resources. Typically, separate pathways have been considered to extract hazardous transition metals or phosphate independently from each other. Investigations on the simultaneous removal of multiple components have been carried out only to a limited extent. Here, we report the synthesis routes for Ni- and Co-struvites (NH4MPO4·6H2O, M = Ni2+ and Co2+), which allow for P, ammonia, and metal co-precipitation. By evaluating different reaction parameters, the phase and stability of transition metal struvites as well as their crystal morphologies and sizes could be optimized. Ni-struvite is stable in a wide reactant concentration range and at different metal/phosphorus (M/P) ratios, whereas Co-struvite only forms at low M/P ratios. Detailed investigations of the precipitation process using ex situ and in situ techniques provided insights into the crystallization mechanisms/crystal engineering of these materials. M-struvites crystallize via intermediate colloidal amorphous nanophases, which subsequently aggregate and condense to final crystals after extended reaction times. However, the exact reaction kinetics of the formation of a final crystalline product varies significantly depending on the involved metal cation in the precipitation process: several seconds (Mg) to minutes (Ni) to hours (Co). The achieved level of control over the morphology and size makes precipitation of transition metal struvites a promising method for direct metal recovery and binding them in the form of valuable phosphate raw materials. Under this paradigm, the crystals can be potentially up-cycled as precursor powders for electrochemical or (electro)catalytic applications, which require transition metal phosphates. KW - Crystallization KW - Struvite KW - Nickel KW - Cobalt KW - Phosphorous recovery KW - Up-cycling KW - Aqueous synthesis PY - 2022 DO - https://doi.org/10.1021/acs.cgd.2c00284 VL - 22 IS - 7 SP - 4305 EP - 4315 PB - ACS Publications CY - Washington D.C. AN - OPUS4-55286 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bach, S. A1 - Visnow, E. A1 - Panthöfer, M. A1 - Gorelik, T. A1 - de Oliveira Guilherme Buzanich, Ana A1 - Gulo, A. A1 - Kolb, U. A1 - Emmerling, Franziska A1 - Lind, C. A1 - Tremel, W. T1 - Hydrate networks under mechanical stress – A case study for Co3(PO4)2·8H2O N2 - The nature of the bound water in solids with hydrogen-bonded networks depends not only on temperature and pressure but also on the nature of the constituents. The collapse and reorientation of these network structures determines the stability of hydrated solids and transitions to other crystalline or amorphous phases. Here, we study the mechanochemically induced loss of bound water in Co₃(PO₄)₂·8H₂O and compare this process to the behavior under hydrostatic pressure. The associated phase transition and its kinetics were monitored by X-ray powder diffraction with Synchrotron radiation and quantitative IR spectroscopy. High shearing forces are responsible for the degradation of the hydrogen-bonded network and the concomitant crystalline–amorphous transformation. UV/Vis spectroscopy, extended X-ray absorption spectroscopy (EXAFS), and X-ray absorption near-edge spectroscopy (XANES) provided information about the short-range order in the amorphous solid, and thermal analysis revealed its composition and showed that the moderate charge densities of the Co²⁺ and PO₄³⁻ ions, which make the hydration enthalpy comparable to the binding energy of the counteranions, and the Formation of hydrogen-bonded networks favor multistage crystallization processes associated with the release and uptake of coordinated water. The changes of the Co²⁺ coordination induce a color change from pink to blue; therefore, Co₃(PO₄)₂·8H₂O can be used as an overheat temperature indicator. KW - Mechanochemistry KW - Amorphous materials KW - Hydrates KW - Cobalt KW - Phosphates PY - 2016 DO - https://doi.org/10.1002/ejic.201501481 SN - 1434-1948 SN - 1099-0682 VL - 2016 IS - 13-14 SP - 2072 EP - 2081 PB - Wiley-VCH Verlag GmbH & Co. KGaA CY - Weinheim, Germany AN - OPUS4-36434 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cakir, Cafer Tufan T1 - Bayesian optimization for depth resolved analysis of complex alloys with grazing exit XANES N2 - Compositionally complex alloys (CCAs) are a new class of alloys containing at least 5 elements with concentrations between 5 and 35 atomic percent. Due to their adjustable composition, which enables modifications of mechanical properties (such as hardness, strength and ductility etc) and their stability at high temperatures, CCAs have been the focus of various studies [1,2]. Especially the corrosion behavior of CCAs has been a wide research interest. However, there are only few studies that deals with the degradation process on such materials, which is highly relevant for the safety aspect for future component design. To thoroughly investigate the corrosion processes and to determine oxidation states of metal components within the reaction products, we need special analytical tools. Since the grazing exit X-ray fluorescence (GEXRF) offers a non-destructive way to collect notable information regarding the high temperature oxidation, we consider it as a useful method to investigate how CCAs behave in corrosive environments. The main idea of grazing geometry is to enhance the fluorescence signal of the surface. This enables highly sensitive surface analyses of thin protective film on surface in sub-micrometer scale [3]. When compared to a conventional CCD-based camera, the advantage and most important feature of the detector system (Color X-Ray Camera (CXC)) is that each pixel is an energy sensitive detector. The position and area sensitive detector, with 264x264 pixel detector area, provides information regarding the signal emitted from the sample as a function of the emission angle and thus allows depth-sensitive analysis. Furthermore, the data collected from samples of an incidence energy which can be controlled with a resolution of 0.5 eV provides XANES data to determine oxidation states. In this contribution, we address the feasibility of our setup and new optimization procedure (Bayesian Optimization and Gaussian Regression). The results of a conceptual study regarding layer properties of the reference sample (Cr-Oxide layer (300nm) on Cr layer (500nm) on Si wafer) and CrCoNi (Cr-Oxide (>1µm) layer on CrCoNi substrate) medium entropy alloy. T2 - European Conference on X-ray Spectrometry. EXRS 2022 CY - Bruges, Belgium DA - 26.06.2022 KW - GEXRF KW - High entropy alloys KW - XANES KW - Grazing exit KW - High entropy materials KW - XAS KW - Optimization PY - 2022 AN - OPUS4-56272 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -