TY - CONF A1 - Komann, Steffen A1 - Gröke, Carsten A1 - Droste, Bernhard T1 - Assessment of quality assurance measures for radioactive material transport packages not requiring competent authority design approval N2 - The majority of transports of radioactive materials are carried out in packages which don’t need a package design approval by a competent authority. Low-active radioactive materials are transported in such packages e.g. in the medical and pharmaceutical industry and in the nuclear industry as well. Decommissioning of NPP’s leads to a strong demand for packages to transport low and middle active radioactive waste. According to IAEA regulations the “non-competent authority approved package types” are the Excepted Packages and the Industrial Packages of Type IP-1, IP-2 and IP-3 and packages of Type A. For these types of packages an assessment by the competent authority is required for the quality assurance measures for the design, manufacture, testing, documentation, use, maintenance and inspection (IAEA SSR 6, § 306). In general a compliance audit of the manufacturer of the packaging is required during this assessment procedure. Their regulatory level in the IAEA regulations is not comparable with the “regulatory density” for packages requiring competent authority package design approval. Practices in different countries lead to different approaches within the assessment of the quality assurance measures in the management system as well as in the quality assurance program of a special package design. To use the package or packaging in a safe manner and in compliance with the regulations a management system for each phase of the life of the package or packaging is necessary. The relevant IAEA-SSR6 § 801 requires documentary verification by the consignor concerning package compliance with the requirements. T2 - WM2013 Conference CY - Phoenix, Arizona, USA DA - 24.02.2013 PY - 2013 SN - 978-0-9836186-2-1 SP - 1 EP - 8 CY - Phoenix, Arizona, USA AN - OPUS4-28504 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schälike, Stefan A1 - Mishra, Kirti Bhushan A1 - Malow, Marcus A1 - Berger, Anka A1 - Wehrstedt, Klaus-Dieter A1 - Schönbucher, A. ED - Pierucci, S. ED - Klemes, J.J. ED - De Rademaeker, E. ED - Fabiano, B. ED - Buratti, S.S. T1 - Mass burning rate of a large TBPB pool fire - experimental study and modeling N2 - Data and prediction for the mass burning rate of a tert-butyl-peroxy-benzoat (TBPB) pool fire (pool diameter = 3 m) is presented. The mass burning rates of TBPB fires are up to six times higher and less dependent on pool diameter compared to hydrocarbon pool fires caused by an additional heat release rate due to exothermic decomposition reaction in the liquid phase. This heat release rate is calculated using a 1st order reaction kinetic obtained from micro calorimetric measurements. A new model is derived considering the heat release rate due to the decomposition reaction which is shown to be 100 % of the heat release rate radiated to the pool surface. With the presented model, including also physical quantities, especially the limiting fuel concentration for upward flame propagation, it is possible to predict the mass burning rates of large TBPB pool fires. The predicted values are in very good agreement with the experiments. T2 - 14th International symposium on loss prevention and safety promotion in the process industries CY - Florence, Italy DA - 12.05.2013 KW - Mass burning rate KW - TBPB (tert-butyl-peroxy benzoat) KW - Pool fire KW - Experimental study KW - Modeling PY - 2013 SN - 978-88-95608-22-8 DO - https://doi.org/10.3303/CET1331143 SN - 1974-9791 N1 - Serientitel: Chemical engineering transactions – Series title: Chemical engineering transactions IS - 31 SP - 853 EP - 858 PB - AIDIC, Associazione Italiana di Ingegneria Chimica CY - Milano AN - OPUS4-28501 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Klippel, Alexander A1 - Scheid, Marc A1 - Krause, U. ED - Makhviladze, G. ED - Molkov, V. ED - Bradley, D. ED - Sunderland, P. ED - Tamanini, F. T1 - Progress on the research into the influence of dustiness on dust explosions N2 - In practice, occurring explosive dust/air mixtures are usually not homogeneous and in many cases do not spread over the whole enclosure. For the safety measure explosion venting, a smaller venting area might be sufficient as calculated according to venting standards (EN 14491 'Dust Explosion Venting Protective Systems'). The tendency of bulk materials to form dust clouds is not taken into account so far. To optimize the design of explosion protection measures, a new safety characteristic the so-called 'dustiness' (see VDI 2263 part 9 'Determination of Dustiness of Bulk Materials'.) could be useful. Dustiness means the tendency of dust to form dust clouds. There are six dustiness groups (DG) from one to six (one means little tendency to stay airborne, six the opposite). The paper describes first results on the reasons for different dustiness and on dust explosion venting for several dusts of different dustiness. A 75 L vertical tube apparatus for vented dust explosion experiments was created. Pressure, pressure rises and flame speeds were measured to evaluate the course of the dust explosions. In addition the paper includes CFD simulations (ANSYS CFX) about the possibilities to model the dust/air mixtures with the Euler/Lagrange approach. In order to simulate the settling of dust clouds more realistic the particle surface area was adjusted and the particle size distribution was taken into account. Results were compared to experimentally determined terminal velocities. T2 - ISFEH7 - 7th International seminar on fire & explosion hazards CY - Providence, RI, USA DA - 05.05.2013 KW - CFD KW - Dust explosions KW - Dustiness KW - Venting PY - 2013 SN - 978-981-07-5936-0 SN - 978-981-07-5940-7 DO - https://doi.org/10.3850/978-981-07-5936-0_13-01 SP - 781 EP - 790 PB - Research Publishing AN - OPUS4-28502 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zencker, Uwe A1 - Qiao, Linan A1 - Kasparek, Eva Maria A1 - Völzke, Holger T1 - Modeling of cylindrical casks under horizontal drop test conditions N2 - Cylindrical casks made of ductile cast iron are used for transport, interim storage and final disposal of radioactive waste in Germany. A basic design criterion is the ability to withstand a horizontal drop without impact Binders onto a foundation representative for the real ground of a storage facility. The increasing use of more cost-effective material compositions requires optimized cask geometries to reduce stresses and strains in the cask structure. For example, a non-uniform wall thickness was introduced to reduce maximum wall bending stresses. As a result, the load characteristics changed from line load to point load at bottom and lid side under horizontal drop fest conditions. Hereby, the position of highest stress inside the structure has shifted significantly. This was the reason for a systematic investigation of effects caused by small design changes or small variations of fest conditions. It led to a better understanding of the positions of high local stresses, their time history and maximum value for cylindrical casks under horizontal drop test conditions. Hence, the paper presents the lessons learnt from modeling and simulating such scenarios considering an impact without limiters onto a realistic target. T2 - 14th International high-level radioactive waste management conference CY - Albuquerque, New Mexico, USA DA - 28.04.2013 KW - Cylindrical cask KW - Ductile cast iron KW - Numerical simulation KW - Horizontal drop test KW - Storage facility KW - Concrete foundation PY - 2013 SN - 978-1-62748-644-6 SP - 1114 EP - 1119 (Paper # 6862) PB - Omnipress AN - OPUS4-28529 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wolff, Dietmar A1 - Jaunich, Matthias A1 - Stark, Wolfgang T1 - Investigating the performance of rubber seals at low temperatures N2 - Rubbers are widely used as main sealing materials for Containers for low and intermediate level radioactive waste and as additional component to metal seals in spent fuel and high active waste containers. The save enclosure of the radioactive container inventory has to be guaranteed according to legislation and appropriate guidelines for long term storage periods as well as down to temperatures of -40 °C for transportation. Therefore the understanding of failure mechanisms that lead to leakage at low temperatures is necessary to ensure a proper material choice which is certainly also influenced by additional factors as e.g. the aging behavior. T2 - 14th International high-level radioactive waste management conference CY - Albuquerque, New Mexico, USA DA - 28.04.2013 KW - Rubber seals KW - Elastomers KW - Compression set KW - Low temperature KW - Leakage rate PY - 2013 SN - 978-1-62748-644-6 SP - 1 EP - 7(Paper # 6888) PB - Omnipress AN - OPUS4-28530 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pfeil, Norbert A1 - Jochum, C. A1 - Mitropetros, K. A1 - Schmelzer, P.G. ED - Pierucci, S. ED - Klemes, J.J. ED - De Rademaeker, E. ED - Fabiano, B. ED - Buratti, S.S. T1 - Keeping and improving process and plant safety competence - what is needed, what should be done? N2 - In March 2004 with the position paper “Maintaining and improving competence in safety engineering” of the DECHEMA/GVC Research Committee "Safety Engineering in Chemical Plants", an initiative came up against the tendency that more and more process and plant safety (PPS) orientated professorships turn to other more fashionable research topics. The Research Committee was concerned that PPS in both academic teaching and research could suffer a negative development - despite of its importance. In 2009 a corresponding Dutch initiative followed. To bring these both and other similar initiatives together, within the 8th European Congress of Chemical Engineering held in Berlin in September 2011 a two days Special session on PPS competence was jointly organized by EFCE, ProcessNet and EPSC. All presentations and conclusions drawn by the organizers (the authors of this paper) are electronically available. The paper addresses the before mentioned initiatives, highlights views and results from the ECCE 8’s special session on PPS competence, and indicates steps necessary to be taken and recent developments. T2 - 14th International symposium on loss prevention and safety promotion in the process industries CY - Florence, Italy DA - 12.05.2013 KW - Anlagensicherheit KW - Prozessindustrie KW - Lehre KW - Forschung PY - 2013 SN - 978-88-95608-22-8 DO - https://doi.org/10.3303/CET1331063 SN - 1974-9791 N1 - Serientitel: Chemical engineering transactions – Series title: Chemical engineering transactions IS - 31 SP - 373 EP - 378 PB - AIDIC, Associazione Italiana di Ingegneria Chimica CY - Milano AN - OPUS4-28540 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Liehr, Sascha A1 - Burgmeier, J. ED - Jaroszewicz, L.R. T1 - Quasi-distributed measurement on femtosecond laser-induced scattering voids using incoherent OFDR and OTDR N2 - We propose to use focused femtosecond laser pulses to create scattering damage in standard singlemode optical fibres as reference points for quasi-distributed sensing applications. Such sensor fibres are interrogated with incoherent optical frequency domain reflectometry (I-OFDR) technique and optical time domain reflectometry (OTDR). A performance comparison of both techniques with the clear advantage of the I-OFDR is presented as well as a quasi-distributed length change measurement application. Also dynamic measurement based on the I-OFDR technique is demonstrated on a femtosecond laser-induced sensor chain. T2 - EWOFS 2013 - 5th European workshop on optical fibre sensors CY - Kraków, Poland DA - 19.05.2013 KW - Optical fiber sensors KW - Femtosecond laser KW - Strain sensor KW - OFDR KW - OTDR PY - 2013 SN - 978-0-81949-634-8 DO - https://doi.org/10.1117/12.2026780 SN - 0277-786X N1 - Serientitel: Proceedings of SPIE – Series title: Proceedings of SPIE VL - 8794 IS - Paper 8794 - 181 SP - 87943N-1 EP - 87943N-4 AN - OPUS4-28734 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tiebe, Carlo A1 - Hübert, Thomas A1 - Lorek, A. A1 - Wernecke, R. T1 - HUMItrace-Sensorsystem mit neuartigen planaren Spurenfeuchtesensoren N2 - Es wird ein Sensorsystem (HUMItrace III) zur Spurenfeuchtebestimmung in der Prozessmesstechnik vorgestellt. Die Bestimmung der Spurenfeuchte erfolgt mit neuentwickelten planaren Sensoren (HUMItrace-Sensoren) nach dem coulometrischen Messprinzip im Frostpunkttemperaturbereich von -80 °C bis -30 °C mit der Kalibriereinrichtung THG11 durch Mischen von trockenen und befeuchteten Teilgasströmen kalibriert. Die Gasfeuchte von Luft kann in diesem Bereich mit den HUMItrace-Sensoren mit einer erweiterten Unsicherheit von 2 K bestimmt werden. Die Sensoren können aber auch zur Gasfeuchtemessung in Wasserstoff, Stickstoff und Distickstoffmonoxid eingesetzt werden. Eine weitere Kalibriereinrichtung, THG-P12, generiert Prüfgase nach der Permeationsmethode; sie kann in das HUMItrace III Sensorsystem implementiert und zur vor-Ort-Kalibrierung der HUMItrace-Sensoren nach dem Standardadditionsverfahren genutzt werden. T2 - Temperatur 2013 - Verfahren und Geräte in der Temperatur- und Feuchtemesstechnik CY - Berlin, Germany DA - 05.06.2013 PY - 2013 SN - 3-9810021-8-0 SP - 257 EP - 262 AN - OPUS4-28732 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Prager, Jens A1 - Köppe, Enrico A1 - Bartholmai, Matthias T1 - Früherkennung von Strukturschäden mittels geführter Lamb-Wellen N2 - Eine Reihe von Prüfproblemen in der chemischen Industrie, in Kraftwerksanlagen und in Transportsystemen ist aufgrund schwieriger Zugangsmöglichkeiten nur begrenzt technisch bzw. wirtschaftlich effizient durchführbar. Das hier vorgestellte Projekt beinhaltet die Entwicklung eines Verfahrens der zerstörungsfreien Prüfung über weite Entfernungen (bis zu 100 m), das zum Einsatz in automatisierten Messsystemen bzw. zur Integration in Langzeitüberwachungssysteme geeignet ist. Grundlage des Verfahrens ist die gezielte Anregung und Auswertung von Lamb-Wellenmoden, wodurch eine effektive Unterscheidung von Fehler- und Formanzeigen sowie eine Klassifizierung unterschiedlicher Fehlertypen möglich werden. Der Vorteil der Nutzung geführter Wellen für die zerstörungsfreie Prüfung liegt in ihrer vergleichsweise guten Ausbreitungsfähigkeit über weite Entfernungen. Die sich daraus ergebenden Möglichkeiten der Untersuchung großer bzw. schwer zugänglicher Bereiche einer Struktur bieten innovative Ansätze für die Entwicklung robuster Structural-Health-Monitoring-Systeme (SHM). Erst durch die Verfügbarkeit leistungsfähiger Rechentechnik wird ein breiter Einsatz derartiger Verfahren möglich. Die Technik kann zur Materialcharakterisierung an ebenen bzw. zylindrischen, dünnwandigen Flächen aus Metall oder auch CFK genutzt werden. Adressierte Anwendungsfelder sind z.B. die Untersuchung von Flugzeugtragflächen oder Pipelines. Des Weiteren wird der Einsatz solcher Verfahren zur Überwachung sicherheitsrelevanter Bauteile z.B. aus Laminaten angestrebt, wie sie verstärkt in der Luft- und Raumfahrt Anwendung finden. Im Rahmen des Projekts wurde auf Grundlage vorhandener Technik (Wellenanregung mittels Ultraschall-Gruppenstrahlprüfköpfen) ein umfassendes Verständnis für die Technologie und anwendungsrelevante Parameter (Probenmaterial und -dimensionen, Welleneigenschaften, Anregungs-, Transmissions-, Reflektionscharakteristika) gewonnen und Algorithmen zur Erkennung von Schädigungsbildern (z.B. Riss, Loch, Verdünnung) entwickelt. Neben der Algorithmusentwicklung zur Detektion und Analyse von Schadstellen, lag ein Projektschwerpunkt in der Entwicklung einer geeigneten Gerätetechnik. Als sensorisches Elemente wurde Ultraschall-Gruppenstrahlertechnik eingesetzt. Besondere Anforderungen werden an die Technik zur Anregung der Wellenmoden unter Verwendung geeigneter Piezoaktoren gestellt. In diesem Bereich existiert bislang keine kommerziell erhältliche Gerätelösung, weshalb eine Neuentwicklug der Anregetechnik realisiert wurde. Speziell für die hohe Anzahl an Aktorkanälen, die benötigt wird, um unterschiedliche Moden und Wellenformen anzuregen, wurde eine äußerst leistungsfähige Anregeeinheit entwickelt. T2 - 16. GMA/ITG-Fachtagung 'Sensoren und Messsysteme' CY - Nürnberg, Germany DA - 22.05.2012 KW - Lamb-waves KW - Ultrasound KW - Non-destructive evaluation KW - Early-damage-detection KW - Structural health monitoring PY - 2012 SN - 978-3-9813484-0-8 DO - https://doi.org/10.5162/sensoren2012/5.2.1 SP - 531 EP - 540 CY - Wunstorf AN - OPUS4-26008 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neuschaefer-Rube, U. A1 - Bartscher, M. A1 - Neugebauer, M. A1 - Härtig, F. A1 - Goebbels, Jürgen A1 - Ehrig, Karsten A1 - Staude, Andreas T1 - Measurement of micro gears - comparison of optical, tactile-optical and CT-measurements N2 - Micro gears are applied in an increasing quantity in many applications. Therefore, precise measurements are of growing importance to ensure their quality. This contribution describes the measurement of gears of a micro planetary gear set with a tactile probe, a tactile-optical probe, an optical sensor, and computed tomography (CT). For the tactile measurements, a high precision piezoresistive microprobe was used. A so-called fiber probe was applied for tactile-optical measurements. This probe applies image processing to determine the position of the tactile probing element. For all tactile and tactile-optical measurements, single point probing was used. The optical measurements were carried out with an imaging sensor based on focus variation. Due to limited accessibility, on some gears not all regions could be measured by the optical sensor and the tactile-optical probe. In contrast to this, with CT the whole part could be measured with high point density. We used a micro-CT system and carried out measurements with Synchrotron-CT. All the sensors used deliver measurement data in Cartesian coordinates. It is a challenge to transfer these data into coordinates in which gear parameters are defined. For this, special attention must be paid to the determination of the gear axis and to the orientation of the teeth. The applied procedures are detailed for different micro gears. The comparison between data of different measurements was carried out successfully. The deviations between the CT data and the tactile or tactile-optical data lie in the range of only a few micrometers. KW - Micro gears KW - Coordinate metrology KW - Computed tomography KW - Optical sensors KW - Tactile probes PY - 2011 DO - https://doi.org/10.1117/12.872413 SN - 0277-786X SN - 0038-7355 SN - 0361-0748 N1 - Serientitel: Proceedings series – Series title: Proceedings series IS - 7864 SP - 78640H-1 EP - 78640H-9 PB - VDE-Verl. CY - Berlin ; Offenbach AN - OPUS4-25998 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bäßler, Ralph A1 - Weltschev, Margit T1 - UNS S44400 - A low cost and corrosion-resistant alternative to the austenite containing nickel for tank applications N2 - In Germany the “BAM-List - Requirements for Tanks for the Transport of Dangerous Goods” is the basis for substance-related prototype approvals for tank Containers undertaken by the BAM1 - Federal Institute for Materials Research and Testing. Compatibility evaluations of selected metallic materials as well as of polymeric gasket and lining materials under the influence of approximately 7200 dangerous goods have been published in the BAM-List since 1989. The ferritic Steel UNS S44400 (X2CrMoTil8-10, 1.4521) was originally developed as alternative for the austenitic grade AISI316L (X2CrNiMo 17-12-2, 1.4404). Due to its characteristic profile this Steel was qualified for applications requiring high strength values at concomitant adequate corrosion resistance. Because of the lack of Nickel this Steel is a cost-efficient alternative to the Ni-containing austenites. No corrosion test results of UNS S44400 under the influence of dangerous goods were published in the BAM-List so far. Only data on the behavior of AISI 316L are listed. Therefore test specimens of this Steel were exposed to selected corrosive substances in order to compare both steels. Due to the reduced alloy content a reduced corrosion resistance of the Steel UNS S44400 in acidic substances, such as formic acid, acetic acid and sulfuric acid, in comparison to the austenitic CrNiMosteels was expected but not observed. Tests in an alkaline medium showed sufficient resistance. T2 - NACE International Corrosion Conference 2012 CY - Salt Lake City, USA DA - 01.03.2012 KW - Steel KW - Dangerous goods KW - Transport tanks KW - Duplex steel KW - Corrosion KW - 1.4362 KW - X2CrNiN23-4 PY - 2012 SP - 1-7 (C2012-0001290) AN - OPUS4-25979 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Böllinghaus, Thomas A1 - Mente, Tobias T1 - Schadensfälle geschweißter Rohrleitungen und Maßnahmen zur Vermeidung N2 - Aus wirtschaftlich-technischer Perspektive ergeben sich in den letzten zehn Jahren hinsichtlich der Werkstoffinnovation und -auswahl für geschweißte Rohrleitungen im Wesentlichen zwei Entwicklungsrichtungen: Im Bereich der niedriglegierten Stähle werden immer höher festere Feinkombaustähle mit Streckgrenzen von inzwischen über 900 MPa verwendet. Wirtschaftliches Ziel ist hierbei eine möglichst hohe Kosteneinsparung durch Reduktion der Wanddicke. Für korrosionsbeanspruchte Komponenten, unter anderem im Petrochemie- und Energieanlagenbau besteht das wirtschaftliche Ziel primär darin, eine höhere Kosteneinsparung durch neue Legierungskonzepte zu erzielen und zwar möglichst so, dass bei mindestens gleicher Festigkeit auf die Verwendung von teuren Elementen, wie beispielsweise Nickel, verzichtet werden kann. Beispiele hierfür sind insbesondere hochlegierte martensitische Cr-V-Stähle, supermartensitische Stähle, Lean-Duplexstähle, superaustenitische Stähle und austenitische Cr-Mn-Stähle. Für einige der neu eingeführten Grundwerkstoffe sind die Zusatzwerkstoffe noch in der Entwicklung. In jedem Fall stellen diese Werkstoffinnovationen besondere Ansprüche hinsichtlich einer Rissvermeidung während der schweißtechnischen Verarbeitung, um von vornherein riss- bzw. fehlerfreie Rohrleitungen herzustellen, die eine hohe Sicherheit gegen ein Versagen während der Inbetriebnahme und im Verlauf der vorgesehenen Lebensdauer aufweisen. Fast alle dieser neu eingeführten Rohrleitungswerkstoffe weisen eine reduzierte Heiß- oder Kaltrissresistenz vor allem während des Schweißens mit modernen Hochleistungsprozessen, bspw. Laserhybridschweißen, auf. Dabei besteht nach wie vor Forschungsbedarf hinsichtlich der jeweiligen Entstehungsmechanismen. Da es in den letzten zehn Jahren immer häufiger zu Produktionsausfällen und Schadensfällen mit teilweise katastrophalen Konsequenzen gekommen ist, werden die Ursachen und die Vermeidung fertigungsbedingter Heiß- und Kaltrisse im Folgenden zusammengefasst. T2 - 14. Sommerkurs Werkstoffe und Fügen CY - Magdeburg, Germany DA - 23.09.2011 PY - 2011 SN - 978-3-940961-56-3 SP - 45 EP - 54 CY - Magdeburg AN - OPUS4-26196 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gerlitzke, A.-K. A1 - Nörthemann, K. A1 - Lang, M. A1 - Milstrey, M. A1 - Kaufer, R. A1 - Woratz, M. A1 - Banach, Ulrich A1 - Hübert, Thomas A1 - Moritz, W. T1 - Long-term stability of the low energy hydrogen sensor N2 - A silicon MIS-structure prepared with thin layers of the super-ionic conductor LaF3 and Pd is used to detect hydrogen. The sensor is able to detect hydrogen in a concentration range from below one ppm to the lower flammable limit in air which is 4 vol.-%. The chip operates at room temperature which results in an extremely low energy consumption compared to other hydrogen sensors. Only once per day a short heating pulse is necessary to reactivate the sensor chip. In cooperation with the BAM, a long-term experiment was carried out. The duration of the measurement was about three months, with a hydrogen exposure every two weeks. The sensor signal remained stable over the measured period. T2 - IMCS 2012 - 14th International meeting on chemical sensors CY - Nuremberg, Germany DA - 20.05.2012 KW - Hydrogen detection KW - Long-term measurement KW - MIS-structure KW - Low energy sensor PY - 2012 SN - 978-3-9813484-2-2 DO - https://doi.org/10.5162/IMCS2012/P2.5.1 SP - 1571 EP - 1574 PB - AMA Service GmbH CY - Wunstorf AN - OPUS4-26177 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gravenkamp, Hauke A1 - Saputra, A. A. A1 - Song, C. A1 - Prager, Jens ED - Linde, B. B. J. ED - Paczkowski, J. ED - Ponikwicki, N. T1 - Detection of defects in thin-walled structures by means of lamb waves N2 - In this paper the Scaled Boundary Finite Element Method (SBFEM) is applied for the simulation of Lamb waves in cracked plates. This method is highly advantageous to study the interaction of different Lamb wave modes with cracks as the crack is not discretized and no refinement is required around the crack tip. Numerical examples are presented for the reflection of the fundamental symmetric and antisymmetric modes from cracks of different depth. The spatial Fourier transformation is employed to calculate the amplitudes of reflected Lamb wave modes. The results reveal possibilities to obtain details of the crack geometry in non-destructive testing and structural health monitoring applications. T2 - International congress on ultrasonics CY - Gdansk, Poland DA - 05.09.2011 KW - Lamb waves KW - Scaled boundary finite element method KW - Simulation KW - Crack detection PY - 2012 SN - 978-0-7354-1019-0 DO - https://doi.org/10.1063/1.3703223 SN - 0094-243X N1 - Serientitel: AIP conference proceedings – Series title: AIP conference proceedings IS - 1433 SP - 443 EP - 446 PB - American Institute of Physics CY - Melville, NY AN - OPUS4-26203 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grehn, M. A1 - Tsai, W.J. A1 - Höfner, M. A1 - Seuthe, T. A1 - Bonse, Jörn A1 - Mermillod-Blondin, A. A1 - Rosenfeld, A. A1 - Hennig, J. A1 - Achtstein, A. W. A1 - Theiss, C. A1 - Woggon, U. A1 - Eberstein, M. A1 - Eichler, H.J. T1 - Nonlinear optical properties of binary and ternary silicate glasses upon near-infrared femtosecond pulse laser irradiation N2 - Some nonlinear optical properties such as the nonlinear refractive index and the nonlinear effective absorption, as well as the laser-induced single-pulse ablation threshold are characterized for a series of binary and ternary silicate glasses upon irradiation with near-infrared femtosecond laser pulses (800 nm, 130 fs). The laser-induced ablation threshold varies from 2.3 J/cm² in case of potassium silicate glass up to 4.3 J/cm² in case of Fused Silica. Nonlinear refractive indices are qualitatively similar within the range 1.7-2.7×10-16 cm²/W. Complementary optical and physico-chemical properties like band gap energy and the glass transformation temperature have been measured for all the glasses. T2 - International symposium on high power laser ablation 2012 CY - Santa Fe, NM, USA DA - 30.04.2012 KW - Laser-induced damage threshold KW - Laser ablation KW - Nonlinear refractive index KW - Silicate glass systems KW - Glass transformation temperature KW - Coefficient of thermal expansion PY - 2012 SN - 978-0-7354-1068-8 DO - https://doi.org/10.1063/1.4739918 N1 - Serientitel: AIP conference proceedings – Series title: AIP conference proceedings VL - 1464 SP - 660 EP - 670 AN - OPUS4-26318 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ballheimer, Viktor A1 - Wille, Frank A1 - Rolle, Annette A1 - Droste, Bernhard T1 - Mechanical behaviour of high burn-up SNF under normal and accident transport conditions - present approaches and perspectives N2 - Transport packages for spent fuel have to meet the International Atomic Energy Agency requirements for different transport conditions. Physical state of spent fuel and fuel rod cladding as well as geometric configuration of fuel assemblies are important inputs for the evaluation of package capabilities under these conditions. In this paper, the mechanical behaviour of high burn-up spent fuel assemblies under transport conditions is analysed with regard to assumptions to be used in the activity release and criticality safety analysis. In particular the different failure modes of the fuel rods (fine cracks or complete breakage), which can cause release of gas, volatiles, fuel particles or fragments have to be properly considered in these assumptions. In view of the complexity of interactions between the fuel rods as well as between fuel assemblies, basket, and cask containment, the exact mechanical analysis of such phenomena is nearly impossible. The gaps in information concerning the material properties of cladding and pellets, especially for the high burn-up fuel, make the analysis more complicated additionally. In this context some practical approaches based on experiences of BAM Federal Institute for Material Research and Testing within safety assessment of packages for transport of spent fuel are discussed. T2 - ASME 2012 Pressure vessels & piping division conference CY - Toronto, Ontario, Canada DA - 15.07.2012 KW - Fuel rods KW - High burn-up KW - Mechanical behaviour KW - Transport conditions PY - 2012 SP - PVP2012-78302, 1-7 PB - American Society of Mechanical Engineers CY - New York AN - OPUS4-26320 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schempp, Philipp A1 - Pittner, Andreas A1 - Rethmeier, Michael A1 - Tang, Z. A1 - Seefeld, T. A1 - Cross, C.E. ED - Babu, S. S. ED - Bhadeshia, H.K. ED - Cross, C.E. ED - David, S.A. ED - DebRoy, T. ED - DuPont, J.N. ED - Koseki, T. ED - Liu, S. T1 - Influence of alloy and solidification parameters on grain refinement in aluminium weld metal due to inoculation N2 - Refinement of the weld metal grain structure can improve the mechanical properties of the weld and decrease the susceptibility to solidification cracking of the weld metal. In this study, commercial Al Ti5B1 grain refiner was used to refine the microstructure of LB (laser beam) and GTA (gas tungsten arc) aluminum welds by inoculation. The grain refiner additions led to a significant decrease in the weld metal mean grain size whereby a transition from columnar to equiaxed grain structure (Columnar to Equiaxed Transition, CET) was observed. The development of both grain size and shape depended upon the base metal (Al alloys 1050A, 5083 and 6082) and upon the welding process. The GTA welding process allowed a more pronounced and a more efficient refinement than in LB welds. Furthermore, the influence of the solidification conditions on the CET was investigated through temperature measurements in the weld metal. The temperature profiles revealed a faster solidification of LB welds than in GTA welds. The results from the temperature measurements were also used to estimate (according to an existing model) the critical thermal gradient at which the CET occurs. T2 - 9th International conference on trends in welding research CY - Chicago, Illinois, USA DA - 04.06.2012 KW - Aluminium KW - LBW KW - GTAW KW - Grain refinement KW - Alloy 1050A KW - Alloy 5083 KW - Alloy 6082 KW - Al Ti5B1 PY - 2013 SN - 978-1-62708-998-2 SP - 98 EP - 107 PB - ASM international AN - OPUS4-27907 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas A1 - Müller, Werner ED - Kilchert, M. T1 - Aktueller Stand der Zulassung für Geokunststoffe durch die BAM und derzeitige Arbeitsthemen des Fachbeirats und seiner Arbeitsgruppen N2 - Bereits vor der vergangenen Leipziger Deponiefachtagung waren eine Reihe von Zulassungsrichtlinien für Geokunststoffprodukte verabschiedet worden. Dokumente wurden nun überarbeitet und weitere sind hinzugekommen. Die Zulassungsscheine für bereits bestehende und auch neue Zulassungen werden auf dieser Basis für die Produkte erneuert oder erstellt. T2 - 9. Leipziger Deponiefachtagung CY - Leipzig, Germany DA - 26.02.2013 PY - 2013 SP - 29 EP - 43 AN - OPUS4-27901 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Teichmann, Bernd A1 - Krüger, Simone T1 - Systematische Untersuchung des Brandverhaltens und des Feuerwiderstands von Photovoltaik-Modulen einschließlich der Emissionen im Brandfall und Entwicklung eines Prüfverfahrens zum Einfluss von PV-Modulen auf die harte Bedachung N2 - In Deutschland sind z.Zt. über 1 Million PV-Anlagen am Netz [1], Immer häufiger kommen dabei Dünnschichtmodule mit toxikologisch bedenklichen Inhaltsstoffen zum Einsatz wie z.B. Cadmium, Indium oder Selen. Aber selbst die klassischen Silizium Dickschichtmodule enthalten als Kontaktmaterial signifikante Mengen an Blei. Besonders aus Sicht des Brandschutzes werfen sich vor diesem Hintergrund mehrere Fragen auf: Wie groß ist die toxikologische Gefährdung durch PV-Module im Brandfall und wie verhalten sich die Module bei einem Brand? Um hier Transparenz zu schaffen, wurden in diesem Forschungsvorhaben systematische Branduntersuchungen an verschiedenartigen Photovoltaik-Modulen durchgeführt. Als Ergebnis können Aussagen getroffen werden zu: - Brandverhalten, - Feuerwiderstand der Module einschließlich der tragenden Konstruktion, - mechanische Integrität, - Einflüsse auf die harte Bedachung sowie - Emissionen im Brandfall. T2 - Brand- und Explosionsschutztag 2013 CY - Magdeburg, Germany DA - 21.03.2013 PY - 2013 AN - OPUS4-27918 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rhode, Michael A1 - Kromm, Arne A1 - Kannengießer, Thomas ED - Babu, S. S. ED - Bhadeshia, H.K. ED - Cross, C.E. ED - David, S.A. ED - DebRoy, T. ED - DuPont, J.N. ED - Koseki, T. ED - Liu, S. T1 - Residual stresses in multi-layer component welds T2 - 9th International conference on trends in welding research CY - Chicago, Illinois, USA DA - 2012-06-04 KW - Shrinkage restraint KW - Component welding KW - Submerged arc welding KW - Multi-run weld KW - Residual stresses KW - Reaction force KW - XRD KW - Large scale test PY - 2013 SN - 978-1-62708-998-2 SP - 48 EP - 54 PB - ASM international AN - OPUS4-27954 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -