TY - CONF A1 - Madia, Mauro A1 - Zerbst, Uwe A1 - Kiyak, Yusuf A1 - Schork, B. T1 - Ermittlung der Wöhlerkurve von Schweißbindungen mittels bruchmechanischer Methoden N2 - IBESS steht für „Integrale Bruchmechanische Ermittlung der Schwingfestigkeit von Schweißverbindungen“ und ist das Ergebnis eines DFG-AiF-Clusters, an dem acht Partner beteiligt waren. Kernstück ist eine analytische Methode zur bruchmechanischen Beschreibung der Rissausbreitung unter Schwingbelastung, die im IBESS-Teilprojekt A3 entwickelt wurde. Da man es im Bereich der Schwingfes-tigkeit mit kurzen Rissen zu tun hat, auf die die etablierten Methoden der Langriss-bruchmechanik nicht anwendbar sind, wurden Lösungen entwickelt, die es erlauben, sowohl die rissnahen Plastizitätsverhältnisse als auch die mit wachsendem Riss gra-duell zunehmenden Rissschließeffekte quantitativ zu beschreiben. Unter Einbeziehung der sogenannten „zyklischen R-Kurve“, deren experimentelle Methodik ebenfalls im Rahmen des Projekts weiterentwickelt wurde, ist es zudem möglich, Ausgangsrissgrö-ßen vorherzusagen, die auf Dauerfestigkeitsniveau gerade so noch arretieren würden. Dies erlaubt umgekehrt eine Abschätzung der Dauerfestigkeit an den Schweißverbin-dungen sowie die statistisch basierte, analytische Vorhersagen des Zeitfestigkeitsas-tes der Wöhlerkurve. In diesem Aufsatz wird die Methodik vorgestellt und ihre Validie-rung an einem ausgewählten Beispiel diskutiert. T2 - 48. Tagung des Arbeitskreises Bruchmechanik und Bauteilsicherheit CY - Freiburg, Germany DA - 16.02.2016 KW - Ermüdungsrissausbreitung KW - Schwingfestigkeit KW - Schweißverbindungen PY - 2016 SN - 2366-4797 VL - Bericht 248 SP - 211 EP - 224 AN - OPUS4-36186 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sporea, D. A1 - Mihai, L. A1 - Negut, Daniel A1 - Stajanca, Pavol A1 - Krebber, Katerina ED - Kalli, K. ED - Mendez, A. T1 - On-line monitoring of gamma irradiated perfluorinated polymer optical fiber N2 - In this paper, we present the first results regarding the on-line monitoring of gamma-ray exposure effects on a commercial multi-mode perfluorinated polymer optical fiber (PF-POF), type GigaPOF-50SR from Chromis Fiberoptics. Our focus was to evaluate on-line the radiation induced attenuation (RIA) over a wide spectral range (320 nm – 1700 nm), in order to assess the fiber’s radiation hardness and its possible use in radiation detection. An Ocean Optics QE65000 high sensitivity spectrometer and a StellarNet near-IR spectrometer were used to cover the spectral ranges 200 nm – 1μm and 900 nm – 1.6 μm, respectively. Electron paramagnetic resonance was used to monitor the recovery of the irradiation induced centers at room temperature. The study indicated that the optical fiber can be used as radiation monitor at low dose rates by measuring the attenuation in the UV, while higher dose rates irradiation can be observed by RIA monitoring at specific wavelengths in the visible spectral range. T2 - Photonics Europe 2016, Micro-Structured and Specialty Optical Fibers IV CY - Brussels, Belgium DA - 03.04.2016 KW - electron paramagnetic resonance spectroscopy KW - Perfluorinated polymer optical fiber KW - radiation effects KW - gamma irradiation KW - radiation hardness KW - radiation induced attenuation KW - radiation dosimetry PY - 2016 DO - https://doi.org/10.1117/12.2230688 VL - 9886 SP - 98861Q-1 EP - 98861Q-6 PB - SPIE CY - Bellingham, USA AN - OPUS4-35927 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fasano, A. A1 - Woyessa, G. A1 - Stajanca, Pavol A1 - Markos, C. A1 - Stefani, A. A1 - Nielsen, K. A1 - Rasmussen, H. K. A1 - Krebber, Katerina A1 - Bang, O. ED - Kalli, K. ED - Mendez, A. T1 - Creation of a microstructured polymer optical fiber with UV Bragg grating inscription for the detection of extensions at temperatures up to 125°C N2 - We describe the fabrication of a polycarbonate (PC) micro-structured polymer optical fiber (mPOF) and the writing of fiber Bragg gratings (FBGs) in it to enable strain and temperature measurements. We demonstrate the photosensitivity of a dopant-free PC fiber by grating inscription using a UV laser. We further show that PC Bragg gratings can be extended up to at least 3% without affecting the initial functionality of the micro-structured fiber. The response of PC FBGs to temperature up to 125°C is also investigated. Polycarbonate has good mechanical properties and its high temperatureresistance might extend the range of application of polymeric FBGs. T2 - Photonics Europe 2016, Micro-Structured and Specialty Optical Fibres IV CY - Brussels, Belgium DA - 03.04.2016 KW - fiber Bragg gratings KW - Polycarbonate KW - polymers KW - micro-structured polymer optical fibers KW - UV laser inscription KW - optical fiber sensors PY - 2016 DO - https://doi.org/10.1117/12.2227843 VL - 9886 SP - 988619-1 EP - 988619-6 PB - SPIE AN - OPUS4-35928 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gaal, Mate A1 - Bartusch, Jürgen A1 - Schadow, Florian A1 - Köppe, Enrico A1 - Dohse, Elmar ED - Chimenti, D. E. ED - Bond, L. J. T1 - Focusing of ferroelectret air-coupled ultrasound transducers N2 - Air-coupled ultrasound has been applied increasingly as a non-destructive testing method for lightweight construction in recent years. It is particularly appropriate for composite materials being used in automotive and aviation industry. Air-coupled ultrasound transducers mostly consist of piezoelectric materials and matching layers. However, their fabrication is challenging and their signal-to-noise ratio often not sufficient for many testing requirements. To enhance the efficiency, air-coupled ultrasound transducers made of cellular polypropylene have been developed. Because of its small density and sound velocity, this piezoelectric ferroelectret matches the small acoustic impedance of air much better than matching layers applied in conventional transducers. In our contribution, we present two different methods of spherical focusing of ferroelectret transducers for the further enhancement of their performance in NDT applications. Measurements on carbon-fiber-reinforced polymer (CFRP) samples and on metal adhesive joints performed with commercially available focused air-coupled ultrasound transducers are compared to measurements executed with self-developed focused ferroelectret transducers. T2 - 42nd Annual Review of Progress in Quantitative Nondestructive Evaluation CY - Minneapolis, Minnesota, USA DA - 26.07.2015 KW - Ferroelectret KW - Transducer KW - Air-coupled KW - Ultrasonic KW - Focusing PY - 2016 SP - 080001 PB - AIP Publishing CY - Melville, NY, USA AN - OPUS4-35955 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maierhofer, Christiane A1 - Myrach, Philipp A1 - Röllig, Mathias A1 - Jonietz, Florian A1 - Illerhaus, Bernhard A1 - Meinel, Dietmar A1 - Richter, U. A1 - Miksche, R. ED - Chimenti, Dale E. ED - Bond, Leonard J. T1 - Characterization of pores in high pressure die cast aluminum using active thermography and computed tomography N2 - Larger high pressure die castings (HPDC) and decreasing wall thicknesses are raising the issue of casting defects like pores in aluminum structures. Properties of components are often strongly influenced by inner porosity. As these products are being established more and more in lightweight construction (e.g. automotive and other transport areas), non-destructive testing methods, which can be applied fast and on-site, are required for quality assurance. In this contribution, the application of active thermography for the direct detection of larger pores is demonstrated. The analysis of limits and accuracy of the method are completed by numerical simulation and the method is validated using computed tomography. T2 - 42nd Annual Review of Progress in Quantitative Nondestructive Evaluation CY - Minneapolis, Minnesota, USA DA - 26.07.2015 KW - flash thermography KW - aluminum KW - pores KW - computed tomography PY - 2016 SN - 978-0-7354-1353-5 DO - https://doi.org/10.1063/1.4940580 VL - 1706 SP - 110009-1 EP - 110009-8 PB - AIP Publishing LLC CY - Melville, New York, USA AN - OPUS4-35848 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Shokouhi, P. A1 - Heideklang, Rene T1 - Fusion of multi-sensory NDT data for reliable detection of surface cracks: Signal-level vs. decision-level N2 - We present and compare two different approaches for NDT multi-sensor data fusion at signal (low) and decision (high) levels. Signal-level fusion is achieved by applying simple algebraic rules to strategically post-processed images. This is done in the original domain or in the domain of a suitable signal transform. The importance of signal normalization for low-level fusion applications is emphasized in regard to heterogeneous NDT data sets. For fusion at decision level, we develop a procedure based on assembling joint kernel density estimation (KDE). The procedure involves calculating KDEs for individual sensor detections and aggregating them by applying certain combination rules. The underlying idea is that if the detections from more than one sensor fall spatially close to one another, they are likely to result from the presence of a defect. On the other hand, single-senor detections are more likely to be structural noise or false alarm indications. To this end, we design the KDE combination rules such that it prevents single-sensor domination and allows data-driven scaling to account for the influence of individual sensors. We apply both fusion rules to a three-sensor dataset consisting in ET, MFL/GMR and TT data collected on a specimen with built-in surface discontinuities. The performance of the fusion rules in defect detection is quantitatively evaluated and compared against those of the individual sensors. Both classes of data fusion rules result in a fused image of fewer false alarms and thus improved defect detection. Finally, we discuss the advantages and disadvantages of low-level and high-level NDT data fusion with reference to our experimental results. T2 - 42nd Annual Review of Progress in Quantitative Nondestructive Evaluation (QNDE) CY - Minneapolis, USA DA - 26.07.2015 KW - multi-sensory KW - NDT KW - signal-level KW - decision-level PY - 2016 SN - 978-0-7354-1353-5 DO - https://doi.org/10.1063/1.4940634 SN - 0094-243X VL - 1706 SP - Article Number: 180004 PB - AMER INST PHYSICS CY - Melville, USA AN - OPUS4-35870 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jost, M. A1 - Strunck, S. A1 - Heunisch, Andreas A1 - Wiens, A. A1 - Prasetiadi, A.E. A1 - Weickhmann, C. A1 - Schulz, Bärbel A1 - Quibeldey, M. A1 - Karabey, O.H. A1 - Rabe, Torsten A1 - Follmann, R. A1 - Koether, D. A1 - Jakoby, R. T1 - Continuously tuneable liquid crystal based stripline phase shifter realised in LTCC technology N2 - This work presents the design, fabrication and measurements of a low temperature cofired ceramic (LTCC) integrated liquid crystal (LC) phase shifter. The effective permittivity of the phase shifter and therefore its differential phase shift can be tuned continuously by orienting the LC directors with electric fields. The phase-shift demonstrator is designed for Ka-band frequencies around 30 GHz and represents a stripline filled with LC, embedded inside an LTCC multilayer structure, which provides a space-qualified and hermetically-sealed LC cavity within an RF-capable material system. The total length of the device is 37 mm while the phase shifting LC section has a length of 14.6 mm. At 30 GHz it exhibits a differential phase shift of 60° with an insertion loss around 6 dB, resulting in a figure of merit around 10°/dB. An advantage is that the insertion loss is nearly independent of the tuning state of the LC. The response time of the phase shifter, depending on the desired LC orientation, is between 62 ms and 37 s. T2 - EuMC 2015 - 45th European microwave conference CY - Paris, France DA - 07.09.2015 PY - 2015 SN - 978-2-87487-039-2 SP - 1260 EP - 1263 AN - OPUS4-35268 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heunisch, Andreas A1 - de Seauve, Victor A1 - Rabe, Torsten T1 - Pressure-assisted sintering of buried thick film resistors in LTCC N2 - In this work, the effect of the pressure-assisted sintering process on buried thick film resistors integrated in LTCC multilayer has been studied. Four commercial resistor pastes with sheet resistivities between 10 kΩ and 10 MΩ/cm were analyzed. First they were characterized by SEM/EDX, XRD and Laser diffraction to determine composition and particle distribution. The pastes consist of isolating particles and of Ruthenium based particles that are supposed to build the conductive phase. The pastes were screen printed on LTCC green tape (DP 951) and buried in four layer laminates. Sintering was done in two ways, pressureless (PLS) and also pressure-assisted (PAS). The pressureless sintered resistors showed electrical resistance values roughly in the range of the nominal sheet resistivity and only relatively small fluctuation within one sample. The PAS samples on the other hand showed significantly higher resistances and larger deviations. The microstructure of the sintered resistors was again investigated by SEM and XRD. It seems that the resistivity is determined by the ratio of the two Ruthenium phases RuO2 and Pb2Ru2O6.5, where RuO2 has the higher conductivity. Buried resistors cannot be trimmed by a laser to adjust the resistance. But we discovered that a refiring step will reduce and normalize the resistivity of the PAS resistors significantly. T2 - IMAPS/ACerS 11th International CICMT conference and exhibition CY - Dresden, Germany DA - 20.04.2015 KW - LTCC Multilayer KW - Buried thick film resistors KW - Pressure-assisted sintering PY - 2015 SN - 978-1510804562 DO - https://doi.org/10.4071/CICMT-WP21 SP - 239 EP - 244 AN - OPUS4-35254 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pfennig, A. A1 - Wolf, Marcus T1 - High-temperature-high pressure stress-strain testing of materials in CO2-containing saline solutions N2 - In-situ stress-strain testing under corrosive environment, such as corrosive gasses (e.g. CO2) and highly saline water, is a challenge in testing corrosion fatigue of materials, e.g. for geothermal application or CCS (carbon capture and storage). The first corrosion chamber system was designed for performance at ambient pressure up to 100 °C. The second allows for corrosion fatigue testing at high pressure up to 200 bar and 400 °C. The highly flexible corrosion chambers allow for fast changing and easy alignment of test samples, visual monitoring, CAD-camera monitoring electrochemical measurements, O2-partial pressure or gas partial pressure measurement. Novelty is the fixing of the corrosion chamber directly onto the specimen, that guarantees best fitting and enables the test system to be modified easily suiting a variety of fatigue test machines. All parts of the test system are conforming to the technical rules. T2 - TMS 2015 annual meeting and exhibition CY - Orlando, FL, USA DA - 15.03.2015 PY - 2015 SN - 1-11-908241-2 SN - 978-1-119-08241-5 DO - https://doi.org/10.1002/9781119093466.ch123 SP - 1015 EP - 1022 PB - Wiley CY - Hoboken, NJ AN - OPUS4-35270 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Oesch, Tyler T1 - In-situ CT investigation of pull-out failure for reinforcing bars embedded in conventional and high-performance concretes N2 - The use of high-performance concretes holds great promise for many structural applications. This paper investigates the performance of these materials when used in combination with traditional reinforcing bars. An improved understanding of failure during reinforcing bar pull-out from high-performance concretes is needed in order to better predict the embedment length required to develop full reinforcing bar pull-out strength and the required thickness of reinforcing bar cover for adequate corrosion protection. The cracking structures surrounding the reinforcing bars were analyzed using x-ray computed tomography (CT) in order to determine the stress states causing failure. This was accomplished by conducting in-situ reinforcing bar pull-out experiments during CT scanning. A conventional concrete, a high-strength concrete, and a high-strength fiber reinforced concrete were all tested during the experiments. The results of these experiments showed that the levels of brittleness of the different concrete materials had a major impact on the failure mechanisms that they experienced during reinforcing bar pull-out. It was also clear that the specimen geometry and the casting method had a major impact on fiber orientation. The inclusion of fibers within concrete was also found to significantly improve strength and corrosion protection during reinforcing bar pull-out. T2 - 6th Conference on industrial computed tomography (iCT) CY - Wels, Austria DA - 09.02.2016 KW - Fiber KW - Reinforcing bar KW - Computed tomography KW - In-situ KW - High-performance concrete PY - 2016 UR - http://www.ndt.net/article/ctc2016/papers/ICT2016_paper_id83.pdf SN - 1435-4934 VL - 21 IS - 2 SP - ID 18788, 1 EP - 8 AN - OPUS4-35436 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Madia, Mauro A1 - Zerbst, Uwe T1 - Bruchmechanische Bestimmung der Schwingfestigkeit basierend auf der zyklischen R-Kurve N2 - Konventionell wird in der Bauteilauslegung zwischen Konzepten der Schwing- und Betriebsfestigkeit auf der einen und der Bruchmechanik auf der anderen Seite unterschieden. Werden in der Schwingfestigkeitsbewertung Gesamtlebensdauern ermittelt, so sind es in der Bruchmechanik Restlebensdauern bei Vorhandensein eines größeren, d.h., bereits zerstörungsfrei auffindbaren Risses. Daneben gibt es seit längerem Bestrebungen, bruchmechanische Ansätze auch für die Ermittlung der Gesamtlebensdauer fruchtbar zu machen. Der besondere Wert einer solchen Kombination besteht darin, dass die Bruchmechanik die explizite theoretische Behandlung von Eingangsparametern (Kerben, Oberflächenrauhigkeit, Mittelspannung, etc.) erlaubt, die in den konventionellen Ansätzen mit vergleichsweise hoher Ungenauigkeit halbempirisch einbezogen werden. Der Beitrag stellt einen von den Autoren entwickelten bruchmechanischen Ansatz zur Ermittlung von Wöhlerkurven vor, der eine Reihe innovativer Merkmale wie die Anwendung der elastischplastischen Bruchmechanik auf kurze Risse, die Ermittlung der Ausgangsrissgröße aus Rissarrestbetrachtungen, die Beschreibung der transienten Entwicklung des Rissschließeffekts mit Hilfe zyklischer R-Kurven (Risslängenabhängigkeit des Schwellenwertes von der Risstiefe), die theoretische Erfassung von Mehrfachrisswachstum bei Lastniveaus oberhalb der Dauerfestigkeit und statistische Aspekte umfasst. Das diskutierte Beispiel ist eine Schweißverbindung (Stumpfnaht) und wurde im Rahmen des laufenden Cluster-Projektes IBESS (Integrale bruchmechanische Ermittlung der Schwingfestigkeit von Schweißverbindungen) generiert. T2 - 42. Tagung des DVM-Arbeitskreises Betriebsfestigkeit CY - Dresden, Germany DA - 07.10.2015 KW - Bruchmechanik KW - Schwingfestigkeit KW - Zyklische R-Kurve PY - 2015 SN - 1616-5144 N1 - Serientitel: DVM-Bericht – Series title: DVM-Bericht IS - 142 SP - 285 EP - 296 CY - Berlin AN - OPUS4-35299 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberle, Arno A1 - Sievert, Rainer T1 - Numerical analysis of an electronic structure bearing deep cracks N2 - The successive fatigue failure process, i.e. crack initiation and growth up to electrical failure, has been investigated for a flip chip configuration. A cracked and uncracked solder bump was analysed using an unified viscoplastic constitutive model (Chaboche). The electrical failure of a bump seems to be reached in general not before a deep crack has grown into the bump. In order to update the actual loading situation two different cracked structures were calculated. T2 - MicroMat 2000 - 3rd International conference and poster exhibition Micro Materials CY - Berlin, Germany DA - 17.04.2000 PY - 2000 SN - 3-932434-15-3 SP - 582 EP - 585 AN - OPUS4-33827 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gravenkamp, Hauke A1 - Song, C. A1 - Birk, C. T1 - Numerical modeling of waveguides embedded in infinite media N2 - This paper presents recently developed approaches for the numerical simulation of guided elastic waves in structures that are embedded in infinite fluid or solid media. The waveguide is described by the Scaled Boundary Finite Element Method, which is a general semi-analytical method that requires discretization of the boundary only. The influence of the surrounding medium on the wave propagation inside the waveguide is accounted for by appropriate boundary conditions. It is demonstrated that for many practical applications a formulation based on simple dashpot boundary conditions yields sufficiently accurate results. To increase accuracy for fluids, an alternative formulation based on exact boundary conditions and inverse iteration is proposed. This approach is of use particularly if the acoustic properties of the waveguide and surrounding material are similar. T2 - ICSV22 - 22nd International congress on sound and vibration CY - Florence, Italy DA - 12.07.2015 PY - 2015 SN - 978-88-88942-48-3 SN - 2329-3675 SP - 1 EP - 5 AN - OPUS4-33829 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bütefisch, S. A1 - Weimann, T. A1 - Busch, I. A1 - Danzebrink, H.-U. A1 - Gross, Thomas A1 - Unger, Wolfgang A1 - Wirth, Thomas T1 - New reference material for imaging XPS (X-ray photoelectron spectroscopy) instrument characterization N2 - Reference materials without variations in topography are essential for the characterization of imaging XPS (X-ray Photoelectron Spectroscopy) Instruments. Therefore a new fabrication process for this kind of zero-topography reference material was developed at PTB and resulted in first prototypes. The fabrication process and first measurement results will be presented in this paper. T2 - Sensor 2015 - 17th International conference on sensors and measurement technology CY - Nuremberg, Germany DA - 19.05.2015 KW - Imaging XPS KW - Reference material KW - Topography free KW - Micro technology PY - 2015 SN - 978-3-9813484-8-4 DO - https://doi.org/10.5162/sensor2015/P7.1 SP - Chapter P7, 821 EP - 825 AN - OPUS4-33837 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Eberle, Arno A1 - Sievert, Rainer A1 - Schubert, A. ED - Winkler, T. ED - Schubert, A. T1 - On the influence of two different underfill materials on the inelastic thermo-cyclic response of a flip-chip solder bump N2 - The finite element method was used to simulate the thermo-mechanical behaviour of a solder bump configuration on Al2O3 substrate under thermo-cyclic loading between -55 °C and 125 °C. Chaboche's viscoplastic material model was used to describe the Bauschinger effect and the creep/plasticity interaction for the tin-lead solder material. The influence of two different viscoelastic underfill materials (Epoxy+50 % SiO2, Epoxy+70 % SiO2) on the inelastic deformation of the tin-lead solder was analyzed and compared. It may be shown that the thermally matched 'hard' underfiller (Epoxy+70 % SiO2) significantly reduces the accumulated inelastic strain in the bump compared to 'soft' underfiller or no underfill material. On the other hand, the maximum lateral normal stress will increase slightly. PY - 2015 SP - 471 EP - 480 AN - OPUS4-33859 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zerbst, Uwe A1 - Heckel, Thomas A1 - Carboni, M. T1 - Non-destructive testing and fracture mechanics - A short discussion N2 - A discussion is provided on the relation between non-destructive testing (NDT) and fracture mechanics. The basic tasks behind this are to guarantee the safety of a component at a potential hazard loading event, to specify inspection intervals or, alternatively, of demands on NDT for a fixed inspection regime, to plan accompanying measures for cases of temporary continued operation of structures in which cracks have been detected, and, finally, fatigue strength considerations which take into account initial defects. T2 - 42nd Annual review of progress in quantitative nondestructive evaluation conference CY - Minneapolis, Minnesota, USA DA - 2015-07-26 KW - Zerstörungsfreie Prüfung KW - Schwingfestigkeit KW - Schadenstoleranz KW - Bruchmechanik KW - probability KW - damage tolerance KW - railway axles KW - inspection PY - 2016 SN - 978-0-7354-1353-5 DO - https://doi.org/10.1063/1.4940614 SN - 0094-243X VL - 1706 SP - 150002-1 EP - 150002-5 PB - AIP Publishing CY - Melville, New York, USA AN - OPUS4-33866 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kasparek, Eva Maria A1 - Völzke, Holger T1 - Further research on cask impact limiter needed? N2 - Transport and storage casks for medium and high level radioactive waste are subjected to extreme heavy loads during the accidental drop scenarios prescribed by IAEA regulations and national storage acceptance criteria. Subsequently, considerable efforts have been made to optimize impact limiting structures aiming to reduce cask stresses and deformations. Though, their benefits can only fully be exploited, if the energy absorbing behavior is reliable simulated by numerical models which play an increasingly important role in safety assessments. BAM has had conducted the 5-years research project ENREA in order to overcome the problems caused by the use of simplified, not sufficiently validated or even defective computational concepts for damping materials. While major results of the just recently completed program will be presented, the focus is laid on the question whether these Outputs provide a solid foundation for approximating impact limiting structures in all relevant configurations. So far, material models have been implemented for spruce, Polyurethane foams and damping concrete based mainly on small and medium scale compression test results. The experimental program performed at BAM comprised likewise guided drop tests and, especially for concrete, penetration tests. Although the resulting numerical simulations showed good agreement with measured values, it turned out to be necessary to consider further effects with regard to e.g. multiaxial stress States, shearfailures of shock absorbing components and their interaction with enclosed or enclosing structures. Thus, the strengths and application constraints of the actual models will be shown as well as details about further research needs, if any. T2 - RAMTRANSPORT 2015 - International conference on the radioactive materials transport and storage CY - Oxford, UK DA - 19.05.2015 KW - Numerical model KW - Shock absorber KW - Damping concrete KW - Polyurethane foam KW - Radioactive waste storage cask PY - 2015 SP - 1 EP - 8 AN - OPUS4-33992 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Feldkamp, Martin A1 - Nehrig, Marko A1 - Bletzer, Claus Wilhelm A1 - Musolff, André A1 - Wille, Frank T1 - Combustion of wood encapsulated in steel sheets during fire test N2 - Packages for the transport of radioactive material are often equipped with impact limiters consisting of wood, encapsulated by Steel sheets. These impact limiters shall ensure the transport cask meets the IAEA safety requirements. After damage caused by the mechanical tests the package has to withstand a severe fire scenario. According to the regulations during and following the fire test, the specimen shall not be artificially cooled and any combustion of materials of the package shall be permitted to proceed naturally. Due to results of the French institute IRSN it was shown that after the fire test an additional energy supply from a pre-damaged impact limiter should be taken into account. The combustion or smouldering of wood was of interest. BAM started a first test phase to examine the issue of combustion for such kind of package components. The goal was to understand the phenomena under the consideration of relevant regulatory boundary conditions. Several metal buckets were filled with wood and equipped with thermocouples. The test specimens have been prepared with different damage arrangements to take the influence of the mechanical tests into account. This paper shows the experimental Setup and the conduction of the tests. The first test shows that pre-damaged metal encapsulations can lead to smouldering of the wood and with this to a Supplement energy release after the end of the 30 minute fire. The consequence could be, to consider additional thermal loads of wood filled impact limiters to filled the IAEA regulations, if the conditions of the tests are transferable to the safety analysis of the package design. T2 - RAMTRANS 2015 - 10th International conference on radioactive materials transport and storage CY - Oxford, UK DA - 19.05.2015 KW - Typ-B KW - Impact limiter KW - Shock absorber KW - Wood KW - Thermal test KW - Fire test PY - 2015 SP - 1 EP - 9 AN - OPUS4-33407 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mull, Birte A1 - Wilke, Olaf T1 - Photocatalytic degradation of toluene, butyl acetate and limonene under UV and visible light N2 - Since Central Europeans spend most of their time indoors, the quality of the indoor air is important. Sources of volatile organic compounds (VOC) indoors are e. g. building materials, wall and floor coverings and interior equipment, whose emissions might influence the health and wellbeing of people. Photocatalysis is one opportunity to improve the indoor air quality by degrading VOCs ideally to carbon dioxide and water. Titanium dioxide (Ti02) in its anatase modification (band gap of 3.2 eV) is a common used UV-active photocatalytic coating. Because of the lack of UV light indoors Ti02 needs to be modified to be active under visible light too. This work focuses on the photocatalytic degradation of toluene, butyl acetate and limonene under UV LED light and blue LED light in emission test chambers under controlled climatic conditions. These compounds were selected due to their frequent occurrence in the indoor environment and their supply was done with a gas mixing System. Ceramic tiles coated with modified and pure Ti02 were used as photocatalytic active material. Previous results and experimental details were already published by Mull and Wilke (2014). T2 - Healthy Buildings Europe 2015 CY - Eindhoven, The Netherlands DA - 18.05.2015 KW - Titanium dioxide KW - Emission test chamber KW - Volatile organic compounds KW - Blue LED light PY - 2015 SN - 978-90-386-3889-8 SP - 1 EP - 4 AN - OPUS4-33410 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Salg, Steffen A1 - Malow, Marcus A1 - Michael-Schulz, Heike A1 - Gebauer, Marek T1 - Experimentelle und theoretische Untersuchung des Zersetzungsmechanismus deflagrationsfähiger Substanzen N2 - Dieser Beitrag beschreibt Untersuchungen zu Deflagrationen von Azodicarbonamid, welche erstmals in einem Vier-Liter-Autoklaven durchgeführt wurden. Zunächst wird die Reproduzierbarkeit der Messungen mit der neuen Apparatur überprüft. Anschließend wird ein Vergleich mit Messungen in einer offenen Apparatur hergestellt, welche zur Prüfung der Deflagrationsfähigkeit in VDI 2263-1 erläutert ist. Zur Beschreibung der deflagrativen Zersetzungen werden die Kenngrößen Induktionszeit, Deflagrationsgeschwindigkeit, maximaler Druck, maximale und mittlere Druck- und Tempe-raturanstiegsrate herangezogen. Zusätzlich werden in weiteren Versuchen die während einer Deflagration entstehende Gasmenge und die Gasentwicklungsrate bestimmt. Abschließend werden die Druck- und Gasentwicklungsraten miteinander verglichen. Aus den Arbeiten lässt sich folgern, dass der Vier-Liter-Autoklav zur Bestimmung und Beschreibung der Deflagrationsfähigkeit von Azodicarbonamid gut geeignet ist und im Vergleich zu Messungen in offenen Prüfanordnungen eine Reihe von Vorteilen bietet. T2 - 4. Magdeburger Brand- und Explosionsschutztag / 3. vfdb-Workshop Brandschutzforschung CY - Magdeburg, Germany DA - 26.03.2015 KW - Deflagration KW - Geschlossener Behälter KW - Autoklav KW - Gas- und Druckmengenmessung PY - 2015 UR - http://www.iaut.ovgu.de/iaut_media/MBE/4_+MBE+2015/Beitr%C3%A4ge+2015/Salg_Experimentelle+und+theoretische+Untersuchung+des+Zersetzungsmechanismus+deflagrationsf%E2%80%9Ehiger+Substanzen.pdf SN - 978-3-00-048960-0 SP - 1 EP - 13 AN - OPUS4-33411 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Salg, Steffen A1 - Malow, Marcus A1 - Morhenn, H. ED - Pierucci, S. ED - Klemes, J.J. T1 - Investigations of deflagration in a four-litre-autoclave under atmospheric and non-atmospheric conditons N2 - A four-litre-autoclave was used to perform deflagration tests in a closed vessel. The aim was to investigate the suitability of this autoclave and to evaluate different parameters influencing the deflagration. The validation of test results showed that the autoclave is suited for the performance of deflagration tests. In comparison to tests performed in an open system according to VDI 2263-1 the results are in good agreement. In the closed vessel same characteristics as in the open test were determined. In addition, pressure rise and rate of pressure rise have been determined and used to characterise deflagrations. The influence of sample weight, tube diameter, bulk density, initial pressure and temperature was investigated. Furthermore, the emerging gas amount and the rate of gas evolution were determined and compared with pressure curves. The use of a four-litre-autoclave for performing deflagration tests offers several advantages in comparison to an open test. T2 - ICheaP12 - International conference on chemical & process engineering CY - Milan, Italy DA - 19.05.2015 KW - Deflagration KW - Closed vessel KW - Autoclave KW - Reduced pressure PY - 2015 UR - http://www.aidic.it/cet/15/43/344.pdf SN - 978-88-95608-34-1 DO - https://doi.org/10.3303/CET1543344 SN - 2283-9216 N1 - Serientitel: Chemical engineering transactions (CEt) – Series title: Chemical engineering transactions (CEt) VL - 43 SP - 2059 EP - 2064 AN - OPUS4-33414 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wille, Frank A1 - Ballheimer, Viktor A1 - Quercetti, Thomas A1 - Sterthaus, Jens T1 - Consideration of gaps between content and lid within package design assessment N2 - Type B(U) packages for the transport of radioactive material have to withstand accident conditions of transport defined in the regulations of the International Atomic Energy Agency in form of different mechanical (drop) tests with a subsequent thermal test. According to the regulatory requirements the orientation of the package in drop tests shall be such to cause the most damaged state in the components performing the safety functions. For the package Iid system a 9 m drop onto the unyielding target with Iid side downwards is often the most damaging orientation. The impact Ioads acting on the Iid in this orientation result mainly from interaction between Iid and internal content. In case of a movable content its impact onto the inner side of the Iid can cause additional Ioad peaks on the Iid and the Iid bolts. The intensity of the internal collision depends on the position of content relating to Iid at the time of package first contact with target. Due to physical limitations an axial gap, which could be set in "pre-drop" configuration of package or which could spontaneously appear during the drop test, usually does not cover the maximum size possible in specific package design. In this context, the combination of drop tests with post-test analysis can be helpful to better estimate the effect of internal impact. The paper summarizes some aspects of this issue based on the BAM experience in the design assessment of Type B(U) transport packages. Additionally the paper shall support applicants in German approval procedures to reduce rounds of questions and ensure delivery of reliable safety case documents to the authorities. T2 - RAMTRANS 2015 - 10th International conference on radioactive materials transport and storage CY - Oxford, UK DA - 19.05.2015 KW - Transport packages KW - Accident conditions of transport KW - Internal impacts KW - Lid/content interaction KW - Radioactive material PY - 2015 SP - 1 EP - 10 AN - OPUS4-33419 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pfeffer, D. A1 - Scholz, Christian A1 - Belly, C. A1 - Wäsche, Rolf A1 - Schlaak, H.F. A1 - Pott, P.P. T1 - Modular test bed for performance assessment of piezoelectric stick-slip actuators N2 - Stepping piezoelectric actuators based on the stick-slip effect inherently make use of a friction contact between strator and rotor. This contact defines not only the actuator's performance but also is prone to wear and tear. For broad use, the actuator has to be able to perform around 1 million strokes. To assess the actuator's performance in terms of force, speed, mechanical output, electrical input, and long-term stability under different load- and environmental conditions, as well as different friction partners, a dedicated test-bed for a LSPA30µXS motor by Cedrat Technologies has been set up. T2 - Actuator 2014 - 14th International conference on new actuators & 8th International exhibition on smart actuators and drive systems CY - Bremen, Germany DA - 23.06.2014 KW - Piezoelectric actuator KW - Test bed KW - Stick-slip KW - Performance test KW - Micro positioning PY - 2014 SN - 978-3-933339-22-5 SN - 978-3-933339-23-2 SP - P 50, 617 EP - 620 AN - OPUS4-33498 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baier, Jennifa A1 - Beck, Uwe T1 - Plasma-kompatible Partikel für add-on Funktionen in Beschichtungen N2 - Die Plasma-Kompatibilität von Partikeln ist eine Voraussetzung für die Anwendung in Plasmadispersionsschichten. Das Ziel ist die Realisierung von add-on Funktionen auf Oberflächen, in Folien und in Beschichtungen. Obwohl primär Nanopartikel für die beabsichtigten Anwendungen verwendet werden, wurden die Kompatibilitättests zuerst mit Partikeln im unteren Mikrometerbereich durchgeführt, um auf einfache Weise Degradationseffektes des Materials, der Fluoreszenzmarkierung oder der Oberfläche zu untersuchen. T2 - 11. ThGOT - Thementage Grenz- und Oberflächentechnik CY - Zeulenroda-Triebes, Germany DA - 15.09.2015 KW - Plasmatechnik KW - Partikel KW - Kombinationsverfahren PVD-ESI PY - 2015 SN - 978-3-00-046056-2 SP - 16.9.2015, Block A, 1 EP - 3 AN - OPUS4-34279 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Beck, Uwe A1 - Hertwig, Andreas A1 - Sahre, Mario A1 - Stockmann, Jörg M. A1 - Weise, Matthias T1 - Visualisierung von Oberflächenverunreinigungen und Schichtartefakten N2 - Die Oberflächentechnik ist eine Schlüsseltechnologie in nahezu zu allen industriellen Branchen. Mit Ausnahme der mechanischen Stabilität, die das Substrat bereitstellt, werden verschiedenartigste Funktionen materialsparend, zum Teil hochintegriert mit maßgeschneiderten Schichtdesigns unter Ausnutzung von Nano- und Quanteneffekten auf Oberflächen appliziert. Ein Großteil der Fertigungskosten in der Mikro- und Nanotechnik wird durch Reinräume und die Umsetzung ausgeklügelter Reinigungsstrategien zur Vermeidung von Restverschmutzungen und partikulären Belegungen verursacht, da diese unweigerlich zum Bauteilversagen führen. Die Validierung des Reinigungszustandes ist somit von zentraler Bedeutung für die Schichtqualität und Produktfunktionalität. Dies gilt in Abhängigkeit von der Applikation und den vertikalen Schicht- bzw. lateralen Strukturdimensionen sowohl für Fertigungsprozesse im Reinraum als auch für solche in robuster Umgebung. In der Praxis kommt es häufig vor, dass man mikroskopisch scheinbar saubere Substrate erst durch die Beschichtung „enttarnt" und dann Defekte oft mit bloßem Auge sichtbar werden. Noch problematischer ist der Einbau von Verunreinigungen während der Schichtabscheidung, die zunächst nicht sichtbar sind, dann aber zum Bauteilversagen führen. T2 - 11. ThGOT - Thementage Grenz- und Oberflächentechnik CY - Zeulenroda-Triebes, Germany DA - 15.09.2015 KW - Imaging Ellipsometrie KW - Mikroskopie KW - Schleimpflug-Optik PY - 2015 SN - 978-3-00-046056-2 SP - 15.9.2015, Block B, 1 EP - 5 AN - OPUS4-34280 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weltschev, Margit A1 - Kohl, Anka A1 - Haufe, Manuela T1 - Compatibility of polyethylene grades with biofuels and biodiesel-heating oil blends N2 - 8iofuels including ethanol and biodiesel (fatty acid methyl ester) represent an important renewable fuel alternative to petroleum-derived transport fuels. lncreasing biofuels use would bring some benefits, such as a reduction in oil demands and greenhause gas emissions, and an improvement in air quality. T2 - EUROCORR 2015 - European corrosion congress CY - Graz, Austria DA - 06.09.2015 KW - Compatibility KW - Polyethylene grades KW - Biofuels KW - Change in MFR and tensile properties PY - 2015 SP - Paper 16_1074, 1 EP - 11 AN - OPUS4-34203 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weltschev, Margit A1 - Werner, Jan A1 - Jochems, Frank A1 - Heming, Frank T1 - Change in properties of sealing materials in biofuels, biodiesel-heating oil blends, diesel and premium grade fuel at different temperatures N2 - Materials compatibility is a major concern whenever the fuel composition is changed in a fuel system. Therefore frequently used sealing materials such as FKM (fluorocarbon rubber), FVMQ (methyl-fluoro-silicone rubber), VMQ (methyl-vinyl-silicone rubber), EPDM (ethylene-propylene-diene rubber), CR (chloroprene rubber), CSM (chlorosulfonated polyethylene), IIR (butyl rubber), PA (polyamides), N8R (acrylonitrile-butadiene rubber) and PUR (polyester urethane rubber) were exposed to E1 0, diese I fuel with 5% biodiesel, non-aged and 2 year aged 810 (heating oil with 10% biodiesel), and for comparison to pure diese! fuel, standard heating oil and Super plus without bioethanol at 20 °C, 40 oc and 70 oc for 84 days. Mass, tensile strength and breaking elongation of the test specimens were determined before and after the exposure. The visual examination of some elastomer test specimens clearly showed the great volume increase until break or partial dissolution. Shore hardness A and D (for PA) were determined before and after exposure of the test specimens to the biofuels for 42 days. There is not determined a threshold for the reduction in tensile properties and Shore hardness in the international standards. Therefore a threshold of 15% was determined for the evaluation of the compatibility. The sealing materials FKM, EPDM, N8R, FMVQ, CSM and PA were evaluated on the basis of this threshold as resistant in E1 0 at 20 oc and 40 °C. FKM, FVMQ and PA were resistant at 40 oc , and none of the materials were resistant at 70 °C. FKM and FVMQ absorbed much less 810 and swelled less. CR, CSM, EPDM, IIR, N8R and VMQ were not resistant to 810 at all at 20 oc, 40 oc and 70 oc as the decrease in the tensile properties was significantly over 50%. FVMQ and PA could be evaluated as resistant in non-aged and two year aged 810 at 20 oc and 40 oc, whereas FKM was resistant up to 70 °C. FKM, PA and PUR were evaluated as resistant in standard heating oil and pure diese! fuel at temperatures up to 40°C, only FKM was resistant up to 70°C. FVMQ, FKM, N8R, VMQ, CR and IIR can be evaluated as resistant in premium grade fuel Super plus without ethanol at 20 oc. FKM, FVMQ, VMQ and IIR were still resistant at 40 °C. FKM and FVMQ were evaluated as resistant with restrictions at 70 °C. ln summary, it can be therefore stated that the chemical resistance of the fluoropolymers FKM and FVMQ in fuels and biofuels is the best one. T2 - EUROCORR 2015 - European corrosion congress CY - Graz, Austria DA - 06.09.2015 KW - Compatibility KW - Sealing materials KW - Biofuels KW - Tensile properties KW - Shore hardness PY - 2015 SP - Paper 16_173, 1 EP - 11 AN - OPUS4-34204 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Köppe, Enrico A1 - Subaric-Leitis, Andreas A1 - Wilk, Tabea T1 - Auswertung der Messunsicherheit eines Multisensorsystems zur Weg- und Positionsbestimmung sich bewegender Objekte in Gebäuden N2 - In den letzten Jahren ist die Bestimmung der Position eines sich bewegenden Objektes eine immer interessanter werdende Information geworden. Die aktuelle Position oder der zurückgelegte Weg wird mittels miniaturisierter integrierter 3D-Sensoren bestimmt. Durch die Integration dieser Sensoren in moderne Smartphones oder in spezielle robuste Hardware sind die Anwendungsgebiete vielseitig. Die ermittelte Position innerhalb von Gebäuden ist dabei für den Kaufmann innerhalb eines Shoppingcenters aber auch für den Feuerwehrmann im Einsatz wichtig. Für den Kaufmann bedeutet es durch gezielte Angebote potenzielle Kunden anzusprechen und damit seinen Umsatz zu steigern. Für den Einsatzleiter der Feuerwehr ist die genaue Position seiner Feuerwehrmänner im Einsatz lebensrettend und bietet damit eine zusätzliche Sicherheit für die Einsatzkraft. Das hier vorgestellte Multisensorsystem, allgemein als Inertialsystem bezeichnet, und das darauf angewendete Verfahren zur Positionsbestimmung wird in diesem Bericht vorgestellt und näher beschrieben. Die systematischen und zufälligen Messunsicherheitsbeiträge des Inertialsystems und deren Auswirkungen auf die Bestimmung der aktuellen Position und somit auf den resultierenden zurückgelegten Weg werden erörtert. T2 - 7. VDI-Fachtagung Messunsicherheit 2015 - Messunsicherheit praxisgerecht bestimmen - Prüfprozesse in der industriellen Praxis CY - Braunschweig, Germany DA - 19.11.2015 PY - 2015 SN - 978-3-18-092269-0 SN - 0083-5560 N1 - Serientitel: VDI-Berichte – Series title: VDI-Berichte IS - 2269 SP - 173 EP - 181 PB - VDI-Verl. AN - OPUS4-35118 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Edel, M. A1 - Köppe, Enrico T1 - An advanced method for pedestrian dead reckoning using BLSTM-RNNs N2 - Location estimation and navigation, especially on smartphones has shown great progress in the past decade due to its low cost and ability to work without additional infrastructure. However, a challenge is the positioning, both in terms of step detection, step length approximation as well as heading estimation, which must be accurate and robust, even when the use of the device is varied in terms of placement or orientation. In this paper, we propose a scheme for retrieving relevant information to detect steps and to estimate the correct step length from raw inertial measurement unit (IMU) data. This approach uses Bidirectional Long Short-Term Memory Recurrent Neural Networks (BLSTM-RNNs). Designed to take contextual information into account, the network can process data gathered from different positions, resulting in a system, which is invariant with respect to transformation and distortions of the input patterns. An experimental evaluation on a dataset produced from 10 individuals demonstrates that this new approach achieves significant improvements over previous attempts and increase the current state-of-the-art results even in the presence of variations and degradations. We achieved a mean classification rate of 98.5% and a standard deviation of 0.70 for 10000 different test sequences and an average error of 1.45% regarding the step length. Thus is the best result on the task gathered in the experiments compared with competing techniques. T2 - IPIN 2015 - 6th International conference on indoor positioning and indoor navigation CY - Banff, Alberta, Canada DA - 13.10.2015 KW - Indoor positioning KW - Inertial tracking KW - Dead reckoning KW - Deep learning KW - Machine learning PY - 2015 SN - 978-1-4673-8402-5 DO - https://doi.org/10.1109/IPIN.2015.7346954 SN - 2162-7347 SP - Paper 1570149259, 1 EP - 6 AN - OPUS4-35119 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maierhofer, Christiane A1 - Röllig, Mathias A1 - Steinfurth, Henrik A1 - Krankenhagen, Rainer A1 - Mecke, R. A1 - Schiller, M. A1 - Kernchen, A. A1 - Kalisch, U. A1 - Hennen, C. A1 - Meinhardt, J. A1 - Groll, E.T. A1 - Arnold, T. T1 - Detection and characterisation of safety relevant detachments of facade elements using a combination of active thermography and optical scanning methods N2 - In this contribution, the development and application of optical and thermographic methods for the nondestructive evaluation of delaminations, cracks and further substructures in Connection with bulging is presented. Since delaminated fagade elements show geometric as well as thermal anomalies, surface geometry and defects beneath the surface were investigated. As methods, Stereo photogrammetry, a tracking based method for tactile recording of geometric 3D data and active thermography were used. Two case studies were assessed with a combination of these methods: the plaster scratches at the Magdeburg Cathedral and a mural painting in Cobbelsdorf, both located in Germany. While the plaster scratches have been investigated by artificial heating with an infrared radiator, the rural painting was tested by analysing the temperature increase due to solar heating. T2 - NDT-CE 2015 - International symposium non-destructive testing in civil engineering CY - Berlin, Germany DA - 15.09.2015 KW - Active thermography KW - Stereo photogrammetry KW - Tracking sensor KW - Historic plaster KW - Masonry KW - Delaminations KW - Cracks PY - 2015 SN - 1435-4934 SP - 291 EP - 300 AN - OPUS4-35106 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Torge, Manfred T1 - Mittelalterliche Flachglasherstellung und Glasmalerei N2 - Glas ist ein sehr verbreiteter Werkstoff und eines der ältesten Produkte neben Keramik, Eisen und Bronze, die der Mensch schon frühzeitig herzustellen in der Lage war. Es dauerte jedoch Jahrrausende bis zur ersten wissenschaftliche Beschreibung der Glasstruktur. Sie erfolgte erstmals 1903 von TAMMANN als eine stark unterkühlte Flüssigkeit. VOGEL (1992) gibt einen Überblick über die klassischen Glasstrukturtheorien. Ganz allgernein kann Glas als ein anorganisches Schmelzprodukt definiert werden, das abgekühlt und erstarrt ist, ohne zu kristallisieren, weshalb Glas auch durchsichtig ist. Es kann aus einfachen und nahezu überall und unbegrenzt vorhandenen Rohstoffen hergestellt werden. Die Hauptbestandteile sind Sand, Soda, Pottasche und Kalk. Wesentliche Eigenschaften des Glases sind seine gute Verarbeitbarkeit mir verschiedenartigen Techniken wie Gießen, Blasen, Ziehen und die Möglichkeit, durch die Zugabe von unterschiedlichen Oxiden auch farbige Gläser herzustellen. T2 - 9. Konservierungswissenschaftliches Kolloquium in Berlin/Brandenburg CY - Berlin, Germany DA - 20.11.2015 KW - Mittelalterliches Glas KW - Glaszusammensetzung KW - Glasmalerei PY - 2015 SN - 978-3-7319-0270-6 N1 - Serientitel: Arbeitshefte des Brandenburgischen Landesamtes für Denkmalpflege und Archäologischen Landesmuseums – Series title: Arbeitshefte des Brandenburgischen Landesamtes für Denkmalpflege und Archäologischen Landesmuseums IS - 36 SP - 81 EP - 90 PB - Michael Imhof AN - OPUS4-35115 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Köppe, Enrico A1 - Bartholmai, Matthias A1 - Daum, Werner A1 - Gong, Xin A1 - Hofmann, Detlef A1 - Basedau, Frank A1 - Schukar, Vivien A1 - Westphal, Anja A1 - Sahre, Mario A1 - Beck, Uwe T1 - New self diagnostic fiber optical sensor technique for structural health monitoring N2 - Fiber optic sensors have gained increasing importance in recent years and are well established in many areas of industrial applications. In this paper, we introduce a concept of a self-diagnostic fiber optic sensor. The presented sensor is to resolve the problems of embedded fiber optic sensors in complex structures and to enable the validation under operational conditions. For this purpose, different magnetostrictive coated fiber optic sensors were developed and various experiments were performed to verify their mode of operation and to determine the respective reproducibility. The measuring principle is illustrated by obtained experimental results, which showed a change in wavelength from 1 pm at a magnetic field strength change of 0.25 mT. In addition, the temperature characteristics of the implemented magnetostrictive sensor were analyzed and an experimental factor of 1.5 compared to a reference fiber optic sensor was determined. T2 - 32nd Danubia-Adria Symposium on advances in experimental mechanics CY - Starý Smokovec, Slovakia DA - 22.09.2015 PY - 2015 SN - 978-80-554-1094-4 SP - 1 EP - 2 CY - Zilina AN - OPUS4-35173 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Masendorf, R. A1 - Müller, C. A1 - Henkel, C. A1 - Klingelhöffer, Hellmuth A1 - Klubberg, F. A1 - Scholz, A. A1 - Wagener, R. ED - Borsutzki, M. ED - Moninger, G. T1 - DIN 50100 Schwingfestigkeitsversuch - Aktueller Stand der Überarbeitung N2 - DIN 50100 definiert die Bedingungen für den Schwingfestigkeitsversuch, der zur Ermittlung von Kennwerten dient, die das Verhalten metallischer Werkstoffe und Bauteile bei zyklischer Beanspruchung mit einer konstanten Lastamplitude beschreiben (Wöhlerversuch). Die Norm umfasst die Versuchsdurchführung, die Versuchsauswertung sowie die Dokumentation von lastgeregelten Wöhlerversuchen im Zeit- und Langzeitfestigkeitsbereich. Mit DIN 50100 soll erreicht werden, dass die Wöhlerlinien verschiedener Prüfstellen miteinander vergleichbar und die wesentlichen Randbedingungen der Versuchsdurchführung dokumentiert werden. Da die Ergebnisse von Schwingfestigkeitsversuchen streuen, ist die Treffsicherheit für die Schätzung der Kennwerte von der Anzahl der Versuche einer Versuchsreihe abhängig. In Abhängigkeit von einer geforderten Treffsicherheit wird durch die DIN 50100 der erforderliche Stichprobenumfang vorgegeben. T2 - Tagung Werkstoffprüfung 2014 - Fortschritte in der Werkstoffprüfung für Forschung und Praxis CY - Bad Neuenahr, Germany DA - 03.12.2015 PY - 2015 SN - 978-3-514-00816-8 SP - 175 EP - 180 PB - Verlag Stahleisen CY - Düsseldorf AN - OPUS4-35176 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krause, Martin A1 - Kurz, J.H. A1 - Lanata, F. A1 - Krstevska, L. A1 - Cavalli, A. T1 - Needs for further developing monitoring- and NDT-methods for timber structures N2 - For the assessmentand for monitoring of timber structures there are numerous promising methods that enable the quantitative description of the current condition of construction elements or parts of a structure. This concerns material properties like modulus of elasticity, moisture content and density as well as structural properties like dynamic characteristics, localization of inhomogeneities, cracks, and biological attack. During the work in COST Action FP 1101, since 2012 the capability of experimental methods are discussed and compared. This covers electrical and electromagnetic wave methods (resistivity, microwave, Radar, X-Ray), elastic waves (ultrasound, pile testing) and mechanical testing (static and dynamic). Describing and collecting the use of the experimental methods for monitoring purposes was the objective of working group 3 "Monitoring of Timber Structures" of the COST Action. Monitoring capabilities will extend the use of timber structures to further applications in civil engineering. So far, no standard exists but collections of application examples and review papers representing the state of the art. From there needs for further developments regarding monitoring and NDT methods for timber structures can be identified and these are described in this paper. T2 - SHATIS 2015 - 3rd International conference on structural health assessment of timber structures CY - Wroclaw, Poland DA - 09.09.2015 KW - Holz Konstruktionen KW - Monitoring KW - Langzeitverhalten KW - Erdbebensicherheit KW - Historische Bauwerke KW - Ultrasonic echo imaging KW - Historical timber structures KW - Seismic investigation KW - Dynamic tests KW - Anisotropic wave propagation KW - Extending service life PY - 2015 VL - 1 SP - 1 EP - 12 AN - OPUS4-35178 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Krause, Martin A1 - Mayer, K. A1 - Effner, Ute T1 - Ultrasonic echo methods for structural timber N2 - Ultrasonic echo technique with shear waves in the frequency rang of 50 kHz is one of the promising methods for assessment of structural timber and is already frequently applied for this purpose. The article summarizes the state of the art of applying echo measurement via linear measurements as well as the development and first results for an imaging method for this purpose. The highly anisotropic properties of the ultrasonic velocity have to be considered. 3 D ultrasonic imaging results are described for the example of a pedestrian bridge made from Siberian larch. T2 - COST Workshop - Highly performing timber structures: Reliability, assessment, monitoring and strengthening CY - Biel, Switzerland DA - 23.09.2014 KW - Ultrasonic echo KW - SAFT reconstruction calculation KW - Glued-laminated timber (glulam) KW - Footbridge KW - Ultraschallecho KW - SAFT KW - Brettschichtholz PY - 2014 SN - 978-3-9523787-3-1 SP - 77 EP - 82 PB - Bern University of Applied Sciences CY - Bern AN - OPUS4-35179 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fritzsche, Lutz A1 - Knorr, Annett ED - Cozzani, V. ED - de Rademaeker, E. T1 - Specification of the limit temperature Texo for a peroxide synthesis using different estimation methods N2 - A major item of thermal process safety, concerning the industrial realisation of exothermic reactions, is the determination of a temperature, where a reaction can be carried out without risk for humans, environment, and of economic loss. The so-called limit temperature Texo is a safety parameter for the reaction process and should not be mixed up with the Self Accelerating Decomposition Temperature (SADT). The last one refers to a temperature value for safe transportation including specific conditions like transport time and type of containment. In Germany a technical guide (Identification and Control of Exothermic Chemical Reactions, TRAS 410, 2012) specifies three approaches for determining Texo. In this work, all these approaches were applied to specify Texo for the synthesis of three tert-Butyl peroxycarboxylic esters. Peroxycarboxylic esters are a subdivision of organic peroxides, known for their high hazardous potential. Results differed partly significant. Anyhow, all of the used techniques and evaluation methods led to Texo values, which were on the safe side – taken the Texo value estimated by the heat release criterion as reference. This method is considered by the authors as a very accurate one. T2 - CISAP-6 - 6th International Conference on Safety and Environment CY - Bologna, Italy DA - 13.04.2014 KW - Peroxide KW - TRAS410 KW - Process safety PY - 2014 SN - 978-88-95608-27-3 DO - https://doi.org/10.3303/CET1436021 SN - 2283-9216 N1 - Serientitel: Chemical engineering transactions – Series title: Chemical engineering transactions IS - 36 SP - 121 EP - 126 PB - AIDIC, Associazione Italiana di Ingegneria Chimica CY - Milano AN - OPUS4-30618 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Becker, T. A1 - Weisbrich, S. A1 - Euteneuer, F. A1 - Wu, Cheng-Chieh A1 - Neitzel, F. T1 - Neue Möglichkeiten in der Bauwerksüberwachung durch integrierte Analyse von Sensormessungen und 3D-Bauwerksmodell N2 - Die Verwendung offener Standards bietet eine Vielzahl von Möglichkeiten, gerade im Bereich des Datenaustausches, Datenlagerung, aber auch der Interoperabilität. GML und CityGML sind hervorragende Beispiele für die Beschreibung von Realweltobjekten mittels eines offenen Standards wohingegen SensorML dazu dient, Messungen, Sensoren und Messplattformen zu beschreiben. Die Verwendung solcher Standards eröffnet dem Nutzer nicht nur die Möglichkeiten der Verwendung einer gemeinsamen standardisierten Sprache, sondern auch die Nutzung von offenen Servicestandards, wie Web Feature Service (WFS), Web Map Service (WMS) oder von Sensor Observation Services (SOS). Die Kombination von Geodaten- und Sensorstandards in einer Dienste- und Servicearchitektur geht über bisherige am Markt existierende Lösungen hinaus und schafft eine neuartige Plattform für die Bauwerksüberwachung, die weit mehr als ein simples Datenhaltungsmodell darstellt. Die in diesem Beitrag vorgestellte Plattform ermöglicht eine direkte Integration von Sensordaten sowie deren Bereitstellung durch eine offene Standardsprache. Dabei sind alle Zwischenschritte jederzeit über eine offene Diensteschnittstelle adressierbar und können so verschiedenen Akteuren zur Verfügung gestellt werden. Das große Potential und der Mehrwert eines derartigen Informationssystems liegt vor allem in der permanenten Verfüg-barkeit von Mess- und Objektdaten und einer damit verbundenen integrierten Analyse der Sensormessdaten in Kombination mit einem Finite-Elemente-Modell (FEM), basierend auf den Objektdaten. Die automatische Ableitung eines FE-Modells aus dem 3D-Bauwerks-modell, die Visualisierung der FEM-Simulationsergebnisse anhand des Bauwerksmodells, die Bereitstellung von Messrohdaten und Sensorinformationen zu jedem Messzeitpunkt machen die Plattform zu einem universell einsetzbaren Werkzeug im Bereich der Bauwerksüberwachung. In diesem Beitrag werden die einzelnen Bausteine, die verwendeten Standards und die Interaktion der einzelnen Komponenten zu einem Gesamtsystem vorgestellt. T2 - 34. Wissenschaftlich-technische Jahrestagung der DGPF CY - Hamburg, Germany DA - 26.03.2014 KW - 3D-Geoinformation KW - CityGML KW - Finite-Elemente-Methode PY - 2014 VL - 23 SP - Paper 254, 1 EP - 10 AN - OPUS4-30619 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erning, Johann Wilhelm T1 - High lead concentrations in a hot water circulation system: Case study N2 - A new Installation for hot drinking water showed high lead concentrations in the water. The installation was constructed from plastic pipes, the hot water tank from stainless steel. A source for the lead contamination was not obvious, cleaning of the tank and the pipes did result in low lead levels after the cleaning but these rose again after short Operation times. Water samples and samples from the installation were taken and analysed. The high lead values for hot water circulation were confirmed, the cold water System showed no detectable lead values. Metallographie investigations showed selective corrosion of various pipe fittings from dezincification resistant brass. The cause of the lead contamination was the selective corrosion of brass combined with a long retention time of the hot water in the circulation System. T2 - KORMAT 2014 - 21st Conference of materials protection and industrial finish CY - Zagreb, Croatia DA - 10.04.2014 KW - Erwärmtes Trinkwasser KW - Blei KW - Messing KW - Selektive Korrosion KW - Water KW - Lead KW - Selective corrosion KW - Brass PY - 2014 SN - 1848-4255 SP - 1 EP - 6 CY - Zagreb AN - OPUS4-30623 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Mermillod-Blondin, A. A1 - Seuthe, T. A1 - Eberstein, M. A1 - Grehn, M. A1 - Bonse, Jörn A1 - Rosenfeld, A. ED - Gorecki, C. ED - Asundi, A. K. ED - Osten, W. T1 - Quantitative estimate of fs-laser induced refractive index changes in the bulk of various transparent materials N2 - Over the past years, many applications based on laser-induced refractive index changes in the volume of transparent materials have been demonstrated. Ultrashort pulse lasers offer the possibility to process bulky transparent materials in three dimensions, suggesting that direct laser writing will play a decisive role in the development of integrated micro-optics. At the present time, applications such as 3D long term data storage or embedded laser marking are already into the phase of industrial development. However, a quantitative estimate of the laser-induced refractive index change is still very challenging to obtain. On another hand, several microscopy techniques have been recently developed to characterize bulk refractive index changes in-situ. They have been mostly applied to biological purposes. Among those, spatial light interference microscopy (SLIM), offers a very good robustness with minimal post acquisition data processing. In this paper, we report on using SLIM to measure fs-laser induced refractive index changes in different common glassy materials, such as fused silica and borofloat glass (B33). The advantages of SLIM over classical phase-contrast microscopy are discussed. T2 - Optical Micro- and Nanometrology V CY - Brussels, Belgium DA - 14.04.2014 KW - Laser material processing KW - Quantitative phase-contrast microscopy KW - Spatial light interference microscopy KW - Nanometrology PY - 2014 DO - https://doi.org/10.1117/12.2051590 VL - 9132 SP - Artikel 91320X, 1 EP - 6 AN - OPUS4-30638 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Woydt, Mathias A1 - Mohrbacher, H. T1 - The use of niobium carbide (Nbc) for wear resistant tribosystems and the tribological backgrounds as cutting tools N2 - The tribological profile of rotating disks made in binder-less niobium Carbide (hot-pressed NbC) and cobalt-bonded NbCs (NbC-8Co and NbC-12Co) mated against alumina (99.7%) were determined under unidirectional sliding tests (0.1 m/s to 8.0 m/s; 22°C and 400°C) as well as in oscillation tests (f= 20 Hz, Ax= 0.2 mm, 2/50/98% rel. humidity, n= 105/l 06 cycles) under unlubricated (dry) conditions. In addition, the microstructure and mechanical properties of HPNbCl and NbC bonded with 8 vol.-% and 12 vol.-% cobalt were determined as well. The tribological data obtained were benchmarked with different ceramics, cermets, hard metals and thermally sprayed coatings, where the NbCs bonded with 8% and 12% Co presented above 7 m/s the lowest wear rates so far in such a bench mark. HP-NbCl, NbC-8Co and NbC-12Co exhibited low wear rates under dry sliding associated with PV high load carrying capacities. The tribological profile established revealed a strong position of NbC bearing materials under tribological considerations and for closed tribo-systems against traditional references. T2 - 9th International conference on tungsten, refractory & hardmaterials CY - Orlando, FL, USA DA - 18.05.2014 KW - Friction KW - Wear KW - Ceramic KW - Oscillation KW - NbC KW - Niobium carbide KW - Cobalt KW - Hard metal KW - Strength KW - Sliding KW - Modulus KW - High temperatures PY - 2014 SN - 978-0-9853397-7-7 SP - 222 EP - 232 AN - OPUS4-31630 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Burbank, John Theodore A1 - Woydt, Mathias T1 - Reaktive Grenzschichten in metallischen Wälzkontakten N2 - Die Ausbildung von tribologisch günstigen Grenzschichten ist eine häufig für die Phase des Einlaufs angenommene Modellvorstellung. Solche tribologisch günstige, durch Reibungsvorgänge im Kontaktbereich induzierte Triboschichten, werden in der Fachliteratur auch als sog. Beilby- und Cervovit-Schichten oder auch als Tribomutationen bezeichnet. Durch eine Vorkonditionierung mittels modifizierter Schmierstoffe oder durch Kaltverfestigung kann der Verschleiß in Wälzkontakten signifikant erniedrigt werden. Bislang ausgeblieben ist eine deutliche Reibungsminderung, aber es wurde keine Reibungserhöhung gemessen. Es waren die Ziele, mithilfe geeigneter Schmierstoffadditive in Verbindung mit dem Prozess des Kaltverfestigens durch das „Dichtwalzen“ (unter Hertz’schen Kontaktpressungen oberhalb von Pmax = 3,0 GPa), ohne Vorschädigung, eine metallurgische Veränderung zu erzielen und gleichzeitig durch einen induzierten Tribofilm geschützte Stahloberfläche zu erhalten, sodass thermochemische Behandlungen durch diese Konzepte einzeln oder kombiniert substituiert werden können. T2 - 55. Tribologie-Fachtagung - Reibung, Schmierung und Verschleiß - Forschung und praktische Anwendungen CY - Göttingen, Germany DA - 22.09.2014 PY - 2014 SN - 978-3-00-046545-1 VL - II SP - 04/1 EP - 04/11 AN - OPUS4-31631 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nakase, Takuya A1 - Kato, S. A1 - Sasaki, S. A1 - Woydt, Mathias T1 - Friction reduction effect of alternative lubricants for plasma electrolytic oxidation coating on AA6061-T6 N2 - Drei verschiedene Grundöltypen (Poly-a-Olefin, Polypropylenglykol und ungesättigte TMP-Ester) und diese Grundöle additiviert mit 2 verschiedenen Additiven (1 Gew.-% ZnDTP oder 1 Gew.-% Dibenzyldisulfid (DBDS)) wurden als Schmiermittel verwendet, um die tribologischen Eigenschaften eines durch plasma-elektrolytische Oxidation behandeltes AA6061-T6 in einem SRV-Tribometer (Toi = 80 °C, Fn = 50N, v = 50 Hz, 2 mm Hub, 2 Stunden) zu bestimmen. Das PPG und die TMP-Ester mit und ohne Additive hatten bessere Schmierfähigkeiten als der PAO. ZnDTP reduziert zwar den Verschleiß, aber erhöht in PAO und PPG die Reibung. Die ungesättigten TMP-Ester + 1 Gew% DBDS zeigten eine um 45% geringere Reibung als PAO + ZnDTP (Referenz) und die Reibung PPG + DBDS war immerhin 30% niedriger. N2 - 3 different base-stocks (poly-a-olefin, polypropylene glycol and unsaturated TMP ester) and these blended with 2 different additives (1wt% ZnDTP or 1wt% dibenzyl disulfide(DBDS)) were used as lubricants to evaluate the tribological properties of AA6061-T6 treated by means of plasma electrolytic oxidation in a SRV tribometer (Toi|=80 °C, Fn = 50N, v= 50 Hz, 2mm stroke, 2hrs). The base oils of PPG and the TMP-ester had better lubricities than the PAO with/without the additives. ZnDTP tend to reduce wear, but when added to PAO and PPG increased the friction. The unsaturated TMP-ester +1wt%DBDS showed 45% lower friction than PAO + ZnDTP (reference), whereas PPG + DBDS had 30% lower friction. T2 - 55. Tribologie-Fachtagung - Reibung, Schmierung und Verschleiß - Forschung und praktische Anwendungen CY - Göttingen, Germany DA - 22.09.2014 PY - 2014 SN - 978-3-00-046545-1 VL - II SP - 42/1 EP - 42/11 AN - OPUS4-31580 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tamura, T. A1 - Nakase, Takuya A1 - Hosohata, S. A1 - Kato, S. A1 - Woydt, Mathias A1 - Wäsche, Rolf A1 - Köhler, Norbert T1 - Zero wear and low friction under dry sliding N2 - In diesem Beitrag werden ungeschmierte Gleitpaarungen auf Basis von Oxidkeramik/DLC vorgestellt, bei denen die tribologischen Kenngrößen mehr oder weniger invariant von der Gleitgeschwindigkeit sind. Die DLC-Dünnschicht besteht aus einem bestimmten Verhältnis an sp2/sp3-hybridisiertem Kohlenstoff. Im Gegensatz zu artgleichen Gleitpaarungen aus MgO-.Zr02, AI2O3 oder SSiC mit Reibungszahlen oberhalb von 0,45, zeigt die Gleitpaarungen aus MgO-Zr02/DLC und alpha-A^OVDLC Festkörpergleitreibungszahlen zwischen 0,075 und 0,15, welche mit ansteigender Gleitgeschwindigkeit leicht abnahmen. Die Verschleißkoeffizienten der DLC-Dünnschichten lagen im Bereich von kleiner als 10~7 mm3/Nm bis herunter zu 10"9 mm3/Nm. N2 - This paper presents a dry sliding tribo-couple (DLC/monolithic oxide ceramics), where the tribological quantities are more or less in a wide ränge independent of the sliding speed. The DLC film is composed of a specific mixture of sp3 /sp2 hybridized carbon. Self-mated ceramic/ceramic couples of MgO-Zr02, alpha-AI203 or SSiC are with their coefficients of friction above 0.45 not so lubricious, whereas the coefficients of friction of the tribocouples MgO-Zr02/DLC and alpha-AbOVDLC ranged between 0.075 and 0.15 under dry sliding. The coefficients of friction for these tribo-couples tend to decrease with increase sliding speed from 0.03 m/s to 6 m/s. The dry wear rates of the thin film is low (<10‘7 mm3/Nm) and perfectly independent from sliding velocity. T2 - 55. Tribologie-Fachtagung - Reibung, Schmierung und Verschleiß - Forschung und praktische Anwendungen CY - Göttingen, Germany DA - 22.09.2014 PY - 2014 SN - 978-3-00-046545-1 VL - II SP - 43/1 EP - 43/7 AN - OPUS4-31581 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Birk, A. M. A1 - Otremba, Frank A1 - Gonzales, F. A1 - Prabhakaran, A. A1 - Borch, Jörg-Peter A1 - Bradley, I. A1 - Bisby, L. ED - de Rademaeker, E. ED - Schmelzer, P. T1 - Fire testing of total containment pressure vessels N2 - Full engulfment fire tests have been conducted on total containment pressure vessels filled to 50% and 98 % capacity with water. The tests included an unprotected tank and tanks with two different levels of thermal protection. Total containment in this context means there was no pressure relief device. The tests were conducted with 1/3rd linear scale rail tank cars similar to the DOT 111 tank cars used in North America. The 2.4 m3 model tanks were subjected to 100 % engulfing fires fuelled by liquid propane. The fire heat flux was approximately 80 % by radiation and 20 % by convection with a total heat flux to a cool surface of approximately 100 kW/m2. T2 - 15th International Symposium on loss prevention and safety promotion (loss 2016) CY - Freiburg, Germany DA - 05.06.2016 KW - fire testing KW - hazmat tanks KW - integrity PY - 2016 SN - 978-88-95608-39-6 DO - https://doi.org/10.3303/CET1648047 VL - 48 SP - 277 EP - 282 PB - AIDIC CY - Milano, Italy AN - OPUS4-36361 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Marotzke, Christian A1 - Feldmann, Titus ED - Thomson, Ole T1 - Characterisation of failure processes of composite plies under transverse loading N2 - For the design of laminates the knowledge of the failure behaviour of plies under multiaxial stresses is a necessary precondition. The strength of plies under multiaxial stresses commonly is determined by standard off-axis tests using fixed clamps. By varying the off axis angle the ratio of shear to normal stresses can be prescribed. However, by preventing the rotation a complex stress field develops which strongly varies with the off axis angle as well. While these effects are not crucial when determining the elastic material parameters since the stress state in the center of the specimen is not far from the ideal uniaxial stress state they have a great influence on the failure behaviour. T2 - ICCM20 CY - Copenhagen, Danmark DA - 19. 07. 2015 KW - debonding KW - composites KW - failure process KW - fracture mechanics KW - energy release rate PY - 2015 UR - www.iccm-central.org/Proceedings/ICCM20proceedings/ VL - 2015 SP - Paper No. 3314-4 page 01 EP - Paper No. 3314-4 page 09 AN - OPUS4-36414 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Häßler, Dustin A1 - Hothan, Sascha ED - Moreyra Garlock, Maria E. ED - Kodur, Venkatesh K.R. T1 - Fire tests of reactive fire protections systems applied to steel tension members with solid circular section N2 - In civil engineering, steel tension members are normally used for bracings, suspensions and underbracing systems. Typically, slim circular solid sections (CSS) are used for such tension members. However, sufficient knowledge about the performance of reactive fire protection systems (RFPS) applied to solid steel tension members has so far been missing. The application of RFPS on such members was not covered by national German approvals (abZ) as well as European technical assessments (ETA) and therefore only possible by approvals in individual case by the building authority. This paper describes the world’s first scientifically investigated fire tests of RFPS applied to steel tension members with CSS. The influence of various parameters such as profile geometry, dry film thickness of the RFPS, level of the load utilization as well as member orientation was tested. In addition, the foaming and cracking behaviour and thermal protection of the RFPS used are investigated and failure mechanisms are identified. To measure the steel temperature of the tension member without weakening the cross-section a special method for the application of thermocouples was developed. The fire tests show that an application of RFPS on steel tension members with solid section is generally possible. However, due to the slim cross-sections and the missing possibility of load distribution within the tension member, high requirements are placed particularly on the effectiveness and reliability of the RFPS. In particular, the testing of mechanically loaded tension members is essential, since the necessary three-dimensional foaming results in the highest stress level for the RFPS. The findings obtained from the performed fire tests are of general nature. Recommendations for the testing and assessment of RFPS applied to steel tension members with solid section are briefly described in this paper and explained in detail in [1] and [2]. Based on this research, the German building authority (DIBt) has defined national approval guidelines for the testing and the assessment of RFPS applied to tension members with solid section. Since November 2015, a general building approval for a RFPS is available in Germany. T2 - 9th International Conference on Structures in Fire CY - Princeton, NJ, USA DA - 08.06.2016 KW - Steel Structure KW - Intumescent Coating KW - Reactive Fire Protection system KW - Fire Tests KW - Tension Member PY - 2016 SN - 978-1-60595-320-5 VL - 9 SP - 1099 EP - 1106 PB - DEStech Publications, Inc. CY - Lancaster, CA, USA AN - OPUS4-36455 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stajanca, Pavol A1 - Mihai, L. A1 - Sporea, D. A1 - Negut, D. A1 - Krebber, Katerina ED - Lewis, E. T1 - Perfluorinated polymer optical fiber for gamma radiation monitoring N2 - The sensitivity of low-loss perfluorinated polymer optical fiber (PF-POF) to gamma radiation is investigated for on-line radiation monitoring purposes. The radiation-induced attenuation (RIA) of a commercial PF-POF based on Cytop material is measured in the visible spectral region. The fiber RIA shows strong wavelength dependence with rapid increase towards the blue side of the spectrum. The wide range of radiation sensitivities is available via careful selection of appropriate monitoring wavelength. The accessible sensitivities span from 1.6 ± 0.2 dBm-1/kGy measured at 750 nm to 18.3 ± 0.7 dBm-1/kGy measured at 420 nm. The fairly high radiation sensitivity as well as its wide tunability makes the fiber a promising candidate for a broad range of applications. T2 - Sixth European Workshop on Optical Fibre Sensors CY - Limerick, Ireland DA - 31.05.2016 KW - Perfluorinated polymer optical fiber KW - Cytop KW - gamma radiation KW - optical fiber sensors KW - radiation dosimetry PY - 2016 UR - http://proceedings.spiedigitallibrary.org/proceeding.aspx?articleid=2525047&resultClick=1 DO - https://doi.org/10.1117/12.2235528 VL - 9916 SP - 99160H-1 EP - 99160H-4 PB - SPIE CY - Bellingham, WA, USA AN - OPUS4-36461 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Grunewald, Thomas A1 - Grätz, Rainer A1 - Hollaender, L. T1 - Ist Edelstahl wirklich funkenärmer als unlegierter Stahl? N2 - Experimentelle Untersuchungen zu streifenden Schlägen mit verschiedenen Edelstahlsorten in explosionsfähigen Atmosphären, jeweils bestehend aus Wasserstoff, Acetylen, Ethylen bzw. Propan mit Luft, haben gezeigt, dass deren Zündwahrscheinlichkeit sowohl von der Art des Brenngas-Gemisches als auch der Höhe der kinetischen Schlagenergie abhängt. Ein Einfluss des Chromgehaltes im Edelstahl auf die Zündwahrscheinlichkeit durch mechanisch erzeugte Schlagvorgänge konnte in dem untersuchten Bereich des Chromgehaltes nicht nachgewiesen werden, obwohl ein steigender Chromgehalt die Oxidationsfähigkeit abgetrennter Partikel erhöhter Temperatur tatsächlich senkt. Ferner haben weitere Werkstoffeigenschaften wie die Wärmeleitfähigkeit, spezifische Wärmekapazität, Dichte und Härte einen Einfluss auf die Zündwahrscheinlichkeit mechanischer Edelstahl-Schlagvorgänge bei Wasserstoff/Luft-Gemischen. Mit steigender Wärmeleitfähigkeit des Edelstahls sinkt die Zündwahrscheinlichkeit. Für die spezifische Wärmekapazität, Dichte und Härte konnte kein Einfluss nachgewiesen werden. Für Schlagvorgänge wurden in der Norm EN 13463-1:2009 Grenzwerte für die maximale kinetische Schlagenergie festgelegt, unterhalb derer die Entstehung einer wirksamen Zündquelle als unwahrscheinlich angenommen werden kann. Dabei wurde zwischen Schlagvorgängen mit funkenarmen Metallen, wie z. B. Kupfer, Messing, und Schlagvorgängen mit sogenannten „sonstigen Werkstoffen“ unterschieden. Die Grenzwerte dieser sonstigen Werkstoffe resultieren aus Versuchen der BAM mit unlegiertem Baustahl. Bei solchen Schlagvorgängen wird von Oxidationsprozessen einzelner Partikel mit dem Luftsauerstoff ausgegangen, die das Gasgemisch aufgrund des hohen Temperaturanstiegs entzünden. In industriellen Anwendungen wie zum Beispiel der chemischen Industrie wird jedoch statt ferritischem Stahl überwiegend Edelstahl verwendet. Im Allgemeinen gilt mit Chrom hochlegierter Edelstahl bei Schlagvorgängen gegenüber ferritischem Stahl als funkenärmer, da die Oxidationsfähigkeit von Edelstahlpartikeln mit steigendem Chromgehalt abnimmt. Aufgrund der abnehmenden Oxidationsfähigkeit postulierte Voigtsberger, dass abgetrennte Edelstahlpartikel mit einem Anteil von 18,11 % Chrom nicht mehr oxidieren können. Bei den eigenen Schlagversuchen der BAM konnte zwar eine sinkende Oxidationsfähigkeit der Partikel, aber keine abnehmende Zündwirksamkeit von Edelstählen mit steigendem Chromgehalt beobachtet werden. T2 - 14. BAM-PTB-Kolloquium CY - Berlin, Germany DA - 14.06.2016 KW - Funken KW - Schlagfunken KW - Mechanisch erzeugte Funken KW - Nichtelektrische Funken PY - 2016 SN - 0938-5533 VL - 2016 SP - 92 EP - 99 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin, Germany AN - OPUS4-36596 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gleis, M. A1 - Simon, Franz-Georg ED - Thomé-Kozmiensky, Karl J. T1 - Novellierung des BVT-Merkblattes Abfallverbrennung – Sachstand, Entwicklungstendenzen und neue Verfahren zur Aufbereitung von Rostaschen und Filterstäuben – N2 - Die europäischen BVT-Merkblätter beschreiben die besten verfügbaren Techniken zum emissionsarmen Betrieb von industriellen Produktionsprozessen, von technischen Verfahren zur Gewinnung und Verarbeitung von Rohstoffen, von Anlagen zur Erzeugung von Strom und Wärme und zur Behandlung und Verwertung von Abfällen und anderen technischen Prozessen. Die Abfallwirtschaft ist bei den Arbeiten zur Revision der BVT-Merkblätter gleich mit zwei Aktivitäten beteiligt, da sich aktuell sowohl das BVT-Merkblatt Abfallbehandlung als auch das BVT-Merkblatt Abfallverbrennung in der Revision befinden. Das Umweltbundesamt hat die Aufgabe, die Überarbeitung der BVT-Merkblätter national zu koordinieren und an den Arbeiten in Sevilla im EIPPC Büro und bei der Europäischen Kommission fachlich mitzuwirken. Der Beitrag beschreibt die aktuellen Aktivitäten zur Revision des BVT-Merkblattes Abfallverbrennung und Stand des Überarbeitungsprozesses auf europäischer Ebene mit dem inhaltlichen Schwerpunkt bei den zu erwartenden Anforderungen an die Entsorgung von Aschen und Schlacken aus der Abfallverbrennung mit einem Schwerpunkt bei den Siedlungsabfallverbrennungsanlagen. T2 - Berliner Konferenz Mineralische Nebenprodukte und Abfälle CY - Berlin, Germany DA - 20.06.2016 KW - Rostasche KW - Abfallverbrennung KW - Aufbereitung PY - 2016 UR - http://www.vivis.de/phocadownload/2016_mna/2016_MNA_163-172_Gleis.pdf SN - 978-3-944310-28-2 VL - 3 SP - 163 EP - 172 PB - TK Verlag Karl Thomé-Kozmiensky CY - Nietwerder AN - OPUS4-36622 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Martin A1 - Erdt, René A1 - Gödde, M. A1 - Salg, St. A1 - Ittemann, L. T1 - Selbstentzündungsverhalten von Feststoffen: Validierung der Extrapolation von Labortests mithilfe halbtechnischer Versuche bis 1 m3 N2 - Vorgestellt wird ein 2018 gestartetes Projekt zur Überprüfung der Extrapolation von im Labormaßstab ermittelten Selbstentzündungstemperaturen auf technisch relevante Volumina. Für die Ermittlung reaktionskinetischer Daten von Feststoffschüttungen stehen eine Reihe von Untersuchungsmethoden zur Verfügung. Dies sind thermische Analysen wie z. B. die differential scanning calorimetry DSC sowie Mikrokalorimetrie zur hochgenauen Messung von Wärmeströmen, bei denen sehr geringe Probenmengen zum Einsatz kommen. In der Regel wird das Selbstentzündungsverhalten jedoch mithilfe von isoperibolen oder adiabaten Warmlagerungsversuchen beurteilt, hier liegen die Probenvolumina üblicherweise im Bereich von ca. 100 cm3 bis zu einigen Litern. Die Extrapolation über mehrere Größenordnungen auf technische Volumina birgt Unsicherheiten, da mit Zunahme des Lagervolumens veränderte Start- und Randbedingungen vorliegen können. Zudem besteht die Möglichkeit, dass bei in technischen Lagern vorherrschenden niedrigen Temperaturen Reaktionen ablaufen, die in Standard- Laborversuchen nicht erfasst werden, aber einen wesentlichen Einfluss auf das Selbstentzündungsverhalten aufweisen können. Hauptziel des Projektes ist es daher, die im Labormaßstab vorhandenen Prüfeinrichtungen durch einen Versuchsstand zur Untersuchung von Probengrößen von bis zu 1000 dm3 zu erweitern, die Eignung (oder Nichteignung) der etablierten Methoden nachzuweisen und im Labormaßstab nicht erfassbare Einflussgrößen zu ermitteln. Zudem sollen anhand der kleinskaligen Tests Entscheidungskriterien abgeleitet werden, ob eine Extrapolation nach den derzeit üblichen Methoden zulässig ist. T2 - 15. BAM-PTB-Kolloquium zur chemischen und physikalischen Sicherheitstechnik CY - Brunswick, Germany DA - 21.05.2019 KW - Selbstentzündung KW - Formalkinetische Daten KW - Halbtechnische Versuche KW - Thermoanalytische Methoden PY - 2020 SN - 0030-834X VL - 130 IS - 1 SP - 9 EP - 18 AN - OPUS4-51285 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -