TY - CONF A1 - Ahmadi, Samim A1 - Hirsch, Philipp Daniel A1 - Lecompagnon, Julien A1 - Hassenstein, Christian A1 - Jung, P. A1 - Caire, G. A1 - Ziegler, Mathias T1 - New techniques in super resolution photothermal imaging for nondestructive testing N2 - In this work we focus on our most recent studies to super resolution (SR) laser thermography. The goal of SR nondestructive testing methods is to facilitate the separation of closely spaced defects. We explain how to combine laser scanning with SR techniques. It can be shown that stepwise as well as continuous scanning techniques are applicable. Finally, we discuss the effect of experimental parameters and im-age processing techniques to find the optimal SR technique which leads to the highest reconstruction quality within laser thermography. T2 - SMSI 2020 Conference CY - Online meeting DA - 22.06.2020 KW - Super resolution KW - Laser thermography KW - Nondestructive testing KW - Laser scanning KW - Photothermal imaging PY - 2020 DO - https://doi.org/10.5162/SMSI2020/C4.1 SP - 169 EP - 170 AN - OPUS4-50895 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ziegler, Mathias A1 - Ahmadi, Samim A1 - Hirsch, Philipp Daniel A1 - Lecompagnon, Julien A1 - Hassenstein, Christian A1 - Thiel, Erik A1 - Pech May, Nelson Wilbur T1 - Using spatial and temporal shaping of laser-induced diffuse thermal wave fields in thermography N2 - The diffuse nature of thermal waves is a fun-damental limitation in thermographic nonde-structive testing. In our studies we investigated different approaches by shaping the thermal wave fields which result from heating. We have used high-power laser sources to heat metallic samples. Using these spatial and temporal shaping techniques leads to a higher detection sensitivity in our measurements with the infra-red camera. In this contribution we show our implementation of shaping laser-induced diffuse thermal wave fields and the effect on the defect reconstruction quality. T2 - SMSI 2020 Conference CY - Online meeting DA - 22.06.2020 KW - Thermal wave KW - Diffusion KW - High-power laser KW - Thermography KW - Spatiotemporal shaping PY - 2020 DO - https://doi.org/10.5162/SMSI2020/C5.1 SP - 179 EP - 180 AN - OPUS4-50897 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lauschkin, Maik A1 - Bulling, Jannis A1 - Lugovtsova, Yevgeniya A1 - Wasmer, P. A1 - Prager, Jens T1 - Bestimmung von Materialparametern aus dem dispersiven Verhalten geführter Wellen mittels neuronaler Netze N2 - Damit eine Simulationsrechnung, beispielsweise mit einer FEM-Software, eine ausreichend hohe Genauigkeit erreicht, muss vorausgesetzt werden, dass die Modellparameter eine sehr hohe Güte aufweisen. Die genaue Kenntnis der Materialparameter ist dabei von besonderer Bedeutung. Um diese Parameter bestimmen zu können, müssen die verwendeten Werkstoffe messtechnisch charakterisiert werden. Neben anderen Ansätzen sind dafür akustische Verfahren im Ultraschallbereich geeignet. Für dünnwandige und plattenförmige Materialien können aus den sich ausbreitenden geführten Wellen messtechnisch Dispersionskurven bestimmt und aus diesen die Materialparameter abgeleitet werden. Da für die Signalverarbeitung und für Optimierungsaufgaben aktuell zunehmend Machine Learning Tools zum Einsatz kommen, stellt sich die Frage, ob diese Werkzeuge auch für die Ermittlung der Materialparameter aus den gemessenen Dispersionskurven eingesetzt werden können. In der vorgestellten Untersuchung soll ein Convolutional Neural Network aufgestellt werden, welches aus Dispersionsbildern Muster extrahiert und aus diesen eine Schätzung für die Materialparameter ermittelt. Um die Machbarkeit dieses Ansatzes zu prüfen, werden zunächst nur isotrope Materialien betrachtet. Für das Netz werden mit der Scaled-Boundary-Finite-Element-Methode synthetische Daten für das Trainieren und Validieren generiert. Zusätzlich werden die Hyperparameter des neuronalen Netzes variiert, um ein optimales Model für die Schätzung zu finden. Anschließend kann das Netz mit experimentellen Daten getestet und das Ergebnis hinsichtlich der Genauigkeit bewertet werden. T2 - DAGA 2020 - 46. Jahrestagung für Akustik CY - Meeting was canceled DA - 16.03.2020 KW - Machinelles Lernen KW - Geführte Ultraschallwellen KW - Materialcharakterisierung KW - Elastische Konstanten KW - Isotrope Materialien PY - 2020 SN - 978-3-939296-17-1 SP - 571 EP - 574 PB - Deutsche Gesellschaft für Akustik e.V. CY - Berlin AN - OPUS4-50765 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kowarik, Stefan A1 - Hicke, Konstantin A1 - Chruscicki, Sebastian A1 - Schukar, Marcus A1 - Breithaupt, Mathias A1 - Lämmerhirt, A. A1 - Pohl, P. A1 - Schubert, M. ED - Cranch, G. ED - Wang, A. ED - Digonnet, M. ED - Dragic, P. T1 - Train monitoring using distributed fiber optic acoustic sensing N2 - We use distributed acoustic sensing to determine the velocity of trains from train vibration patterns using artificial neural network and conventional algorithms. The velocity uncertainty depends on track conditions, train type and velocity. T2 - 27th International Conference on Optical Fiber Sensors (OFS) CY - Meeting was canceled DA - 08.06.2020 KW - Train monitoring KW - Distributed acoustic sensing KW - DAS KW - Distributed fiber optic sensing PY - 2020 SN - 978-1-55752-307-5 DO - https://doi.org/10.1364/OFS.2020.T3.25 SP - 1 EP - 4 PB - The Optical Society (Optical Society of America) CY - Washington D.C., USA AN - OPUS4-50758 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Plarre, Rüdiger ED - Trematerra, P. ED - Conti, B. T1 - Uninvited and welcomed guests in museums – biological management of clothes moths and woodworms N2 - In museums and historic houses clothes, moths (Tineola bisselliella, Tinea pellionella) and the furniture beetle (Anobium punctatum) are the most economically important pests on textiles or wooden artifacts, respectively. Their management is essential to protect cultural ethnological heritage and natural history collections for future generations. Pest management strategies have changed over time. Today, intensive knowledge on pest biology and overall material science are key cornerstones in IPM concepts - also for the Museum environment. The important first steps for sustainable pest management are risk assessment, early pest detection and identification of pathways of infestation. These steps are followed by physical and biological means of control, which have lately gained more importance than applying biocides. Several potentially effective biological enemies of clothes moths and woodworm have been known for a long time, but their promotion for pest control in Museums and historic houses is just beginning. This short review summarizes current concepts of pest life cycle interruption by applying good quarantine and very specific biological measures. The lessons learned from recent faunistic surveys, life-history studies as well as behavioral observations of parasitoids and predators of clothes moths and woodworm may supplement the pest management tool box. The need for further research in this field is addressed. T2 - Working Group Meeting "Integrated Protection of Stored Products" CY - Pisa, Italy DA - 03.09.2019 KW - Corynetes caeruleus KW - Biological control KW - Museum pests KW - Tineola bisselliella KW - Anobium punctatum KW - Apanteles carpatus KW - Baryscapus tineivorus PY - 2020 SN - 978-92-9067-333-0 VL - 148 SP - 266 EP - 273 AN - OPUS4-50543 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Brandes, K. A1 - Kubowitz, P. A1 - Daum, Werner A1 - Hofmann, Detlef A1 - Basedau, Frank T1 - Lagrange Multiplikator-Test zur Detektierung von zunehmender Strukturschädigung N2 - Mit einem auf Lagrange-Multipiikator-Tests basierenden Monitoring von Brücken ist es gelungen, in Belastungsversuchen an einer Holzbrücke (7,25 m Spannweite), an der relativ kleine Schädigungen künstlich herbeigeführt worden waren, die Zuverlässigkeit dieser Art des Monitorings zu bestätigen. Ausgangspunkte waren Messung von Durchbiegungen sowie Krümmungen und die Zusammenführung der jeweiligen Regression mit Nebenbedingungen, die den mechanischen Bedingungen gehorchen, unter Einschluss von Lagrange-Multiplikatoren, die sich als brauchbare Testparameter erwiesen. T2 - 8. Symposium Experimentelle Untersuchungen von Baukonstruktionen CY - Dresden, Germany DA - 24.09.2015 KW - Schadensfrüherkennung KW - Strukturschädigung KW - Monitoring PY - 2015 SN - 1613-6934 N1 - Serientitel: Schriftenreihe Konstruktiver Ingenieurbau Dresden – Series title: Schriftenreihe Konstruktiver Ingenieurbau Dresden IS - 40 SP - 147 EP - 157 CY - Dresden AN - OPUS4-34793 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bernhard, J. A1 - Madia, Mauro A1 - Schork, B. A1 - Kucharczyk, P. A1 - Ngoula, D. A1 - Baumgartner, J. A1 - Schöne, Dieter T1 - Integrale bruchmechanische Ermittlung der Schwingfestigkeit von Schweißverbindungen: Validierung an Stumpfstößen und Kreuzstößen N2 - In diesem Beitrag soll das Validierungskonzept der IBESS-Prozedur, sowie erste Ergebnisse und Erkenntnisse der noch gegenwärtig laufenden Validierung vorgestellt werden. Die Vorstellung erfolgt dabei am Beispiel der im Projekt eingesetzten geschweißten Stumpfstoß- sowie Kreuzstoßverbindung. Neben der Validierung des analytischen bruchmechanischen Modells zur Ermittlung der Schwingfestigkeit, steht auch die Validierung von Kriterien zur Interaktion und Koaleszenz von kurzen Mehrfachrissen im Fokus. T2 - DVS Congress 2015 - Große Schweißtechnische Tagung CY - Nuremberg, Germany DA - 14.09.2015 KW - Schwingfestigkeit KW - Bruchmechanik KW - IBESS PY - 2015 SN - 978-3-945023-46-4 N1 - Serientitel: DVS-Berichte – Series title: DVS-Berichte IS - 315 SP - 306 EP - 310 PB - DVS Media GmbH CY - Düsseldorf AN - OPUS4-34797 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Tchuindjang, D. A1 - Madia, Mauro A1 - Fricke, W. A1 - Hensel, J. T1 - Integrale bruchmechanische Ermittlung der Schwingfestigkeit von Schweißverbindungen: Validierung an Längsstreifen N2 - Zur Validierung der IBESS-Prozedur wurden Schwingfestigkeitsuntersuchungen an Längssteifen aus S355 NL durchführt. Neben dem Einfluss der Mittelspannung wurde der Einfluss der Eigenspannung und der Kerbschärfe experimentell untersucht. Die durchgeführten Schwingfestigkeitsversuche zeigen einen geringen Einfluss der Mittelspannung und der Eigenspannungen, wobei der Einfluss der Nahtgeometrie deutlich sichtbar ist. Proben mit geringerem Nahtanstiegswinkel zeigen eine höhere Schwingfestigkeit, was vor allem auf die längere Rissinitiierungsphase zurückzuführen ist. Die gemessenen und berechneten Schweißeigenspannungen ergeben Quereigenspannungen von bis zu 80% der Streckgrenze. Die zyklische Belastung der Probe zeigt, dass die Eigenspannungen sich beim ersten Lastzyklus signifikant durch Plastifizierung abbauen. Die Simulation des Rissschließens zeigt eine Abhängigkeit vom Lastniveau; von der Mittelspannung und von der Netzdichte. Das Rissschließen tritt an der Plattenoberfläche früher als am tiefsten Punkt des Risses auf. T2 - DVS Congress 2015 - Große Schweißtechnische Tagung CY - Nuremberg, Germany DA - 14.09.2015 KW - Schwingfestigkeit KW - Bruchmechanik KW - IBESS PY - 2015 SN - 978-3-945023-46-4 N1 - Serientitel: DVS-Berichte – Series title: DVS-Berichte IS - 315 SP - 310 EP - 316 PB - DVS Media GmbH CY - Düsseldorf AN - OPUS4-34798 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Madia, Mauro A1 - Zerbst, Uwe A1 - Beier, H.T. A1 - Schöne, Dieter T1 - Analytische Beschreibung von Rissarrest, Kurz- und Langrisswachstum in Schweißverbindungen N2 - Kernstück der angestrebten IBESS-Prozedur ist eine analytische Methode zur bruchmechanischen Beschreibung der Rissausbreitung unter Schwingbelastung. Da man es im Bereich der Schwingfestigkeit mit kurzen Rissen zu tun hat, auf die die etablierten Methoden der Langrissbruchmechanik nicht anwendbar sind, werden Lösungen entwickelt, die es erlauben, sowohl die rissnahen Plastizitätsverhältnisse als auch die mit wachsendem Riss graduell zunehmenden Rissschließeffekte quantitativ zu beschreiben. Unter Einbeziehung der sogenannten "zyklischen R-Kurve", deren experimentelle Methodik ebenfalls im Rahmen des Projekts weiterentwickelt wird, ist es zudem möglich, Ausgangsrissgrößen vorherzusagen, die auf Dauerfestigkeitsniveau gerade so noch arretieren würden. Dies erlaubt umgekehrt eine Abschätzung der Dauerfestigkeit an realen Bauteilen wie eben Schweißnähten sowie die statistisch basierte, analytische Vorhersage des Zeitfestigkeitsastes der Wöhlerkurve. Die im Modell berücksichtigten Parameter bzw. deren statistische Verteilung schließen Werkstoffdaten und die lokale Nahtgeometrie (Nachtübergangsradius, Nahtanstiegswinkel, Einbrandkerben oder Oberflächenrauhigkeit) ein. Im Vortrag wird das analytische Modell vorgestellt und vor dem Hintergrund der im IBESS-Cluster bereitgestellten experimentellen Information diskutiert. T2 - DVS Congress 2015 - Große Schweißtechnische Tagung CY - Nuremberg, Germany DA - 14.09.2015 KW - Schwingfestigkeit KW - Bruchmechanik KW - IBESS PY - 2015 SN - 978-3-945023-46-4 N1 - Serientitel: DVS-Berichte – Series title: DVS-Berichte IS - 315 SP - 300 EP - 306 PB - DVS Media GmbH CY - Düsseldorf AN - OPUS4-34799 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schork, B. A1 - Zerbst, Uwe A1 - Kucharczyk, P. A1 - Bernhard, J. A1 - Kaffenberger, M. A1 - Baumgartner, J. A1 - Oechsner, M. T1 - Imperfektionen für die schwingbruchmechanische Bewertung von Schweißverbindungen N2 - Bruchmechanischen Bewertungsmethoden liegt stets eine tatsachlich vorhandene oder fiktive Anfangsrisslange zu Grunde. Schweißverbindungen sind mit strukturellen Imperfektionen wie beispielsweise lnhomogenitaten in der Mikrostruktur und den Werkstoffeigenschaften behaftet, welche auf der Werkstoffseite berücksichtigt werden können. Imperfektionen wie der Kantenversatz und der Nahtübergangsradius, die als außere geometrische Imperfektionen aufgefasst werden können, haben vor allem Auswirkungen auf den Spannungszustand und werden daher auf der Lastseite erfasst. Innere geometrische Imperfektionen wie Einschlüsse oder Poren, von welchen Risse initiieren und sich ausbreiten, können als Ausgangsrissgröße aufgefasst werden. Im Teilprojekt A1 des Forschungsclusters IBESS wurden außere geometrische Imperfektionen an Schweißverbindungen ermittelt und statistisch ausgewertet. Des Weiteren wurden Schweißverbindungen fraktografisch im Rasterelektronenmikroskop (REM) bezüglich innerer geometrischer Imperfektionen untersucht, jedoch konnten aufgrund der hohen Schweißgütekeine schadigungsrelevanten inneren Imperfektionen (Ausgangsdefekte) detektiert werden. Um dennoch eine Ausgangsrisskonfiguration zu bestimmen, wurden "Heat-Tinting" Versuche eingesetzt, mit denen auf der Bruchflache verschiedene Anrissstadien markiert werden können. Mit dem .Heat-Tinting" Verfahren können sehr kleine Anrisse detektiert und in Abhangigkeit von der Beanspruchung frühe Anrisskonfigurationen ermittelt werden. Des Weiteren haben Zerbst und Madia im Teilprojekt A3 ein Modell entwickelt, mit dem für den Grundwerkstoff mittels zyklischer R-Kurven eine Ausgangsrissgröße rechnerisch ermittelt werden kann. Unter Verwendung der Ergebnisse aus den Versuchen zur Ermittlung der Anrissstadien soll dieses Modell validiert werden, um auch für Schweißverbindungen Anwendung zu finden. T2 - DVS Congress 2015 - Große Schweißtechnische Tagung CY - Nuremberg, Germany DA - 14.09.2015 KW - Schwingfestigkeit KW - Bruchmechanik KW - IBESS PY - 2015 SN - 978-3-945023-46-4 N1 - Serientitel: DVS-Berichte – Series title: DVS-Berichte IS - 315 SP - 271 EP - 277 PB - DVS Media GmbH CY - Düsseldorf AN - OPUS4-34800 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zerbst, Uwe A1 - Beier, H.T. A1 - Nitschke-Pagel, T. T1 - IBESS: Integrale Bruchmechanische Ermittlung der Schwingfestigkeit von Schweißverbindungen - Eine Einführung N2 - Die Projektbezeichnung IBESS steht für .Integrale Bruchmechanische Ermittlung der Schwingfestigkeit von Schweißverbindungen". Ziel des von acht Partnern vorangetriebenen AiF-DFG-Forschungsclusters IBESS ist die Entwicklung eines Ansatzes zur bruchmechanischen Ermittlung der Schwingfestigkeit von Schweißverbindungen. Die Arbeiten umfassen grundlegende Untersuchungen zum Wachstum und Arrest kurzer Risse, zur Ausbildung und Beeinflussung von Schweißeigenspannungen unter zyklischer Last, zum Einfluss der lokalen Nahtgeometrie auf die Rissausbreitung, zum Mehrfachriss-Phänomen oberhalb des Dauerfestigkeitsniveaus sowie zum Koaleszenzverhalten benachbarter Risse. Die gewonnenen Erkenntnisse fließen in ein analytisches Modell zur Ermittlung der Schwingfestigkeit ein, das physikalisch begründete und mithin sehr viel individuellere Vorhersagen des Ermüdungsverhaltens von Schweißnähten ermöglichen soll, als das auf konventioneller Basis bislang möglich ist. Ein nicht geringer Teil der Aktivitäten des Clusters ist mit der Bereitstellung von Daten zur Validierung befasst. Diese wird auf verschiedenen Ebenen vorgenommen, von der Beschreibung des Wachstuns von Einzelrissen über ihr Zusammenwachsen bis hin zur kompletten Wöhlerkurve. Ziel dieses Vortrags ist ein kurzer Überblick über das IBESS-Gesamtprojekt, das dem Zuhörer eine Einordnung der im IBESS-Vortragsblock vorgestellten Einzelaktivitäten ermöglichen soll. T2 - DVS Congress 2015 - Große Schweißtechnische Tagung CY - Nuremberg, Germany DA - 14.09.2015 KW - Schwingfestigkeit KW - Bruchmechanik KW - IBESS PY - 2015 SN - 978-3-945023-46-4 N1 - Serientitel: DVS-Berichte – Series title: DVS-Berichte IS - 315 SP - 265 EP - 271 PB - DVS Media GmbH CY - Düsseldorf AN - OPUS4-34801 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kruschwitz, Sabine A1 - Feldmann, R. ED - Schuhmann, R. T1 - Zerstörungsfreie Feuchtemessung an Estrichen - ein multi-sensorischer Ansatz mit Methodenvergleich N2 - Feuchte und Salz können die Mikrostruktur poröser Baustoffe maßgeblich verändern, oft sind sie die Ursache von sowohl chemischen als auch mechanischen Schädigungen und Korrosion. Im speziellen Fall von Fußbodenestrichen ist gerade die Frage nach der Belegreife für Fußbodenleger von immer wiederkehrender Bedeutung. Dieser Beitrag beschäftigt sich mit den Vor- und Nachteilen verschiedener zerstörungsfreier, feuchtesensitiver Messmethoden und vergleicht die Ergebnisse mit denen der baustellenüblichen zerstörenden Tests. Kapazitive Methoden und Bodenradar scheinen am erfolgversprechensten im Bezug auf flächige Feuchtemessungen, aber auch sie eignen sich derzeit noch nicht als eigenständige, sofort ersetzbare Absolutmessgeräte, sondern eher als schnelle Relativverfahren fürs Monitoring. T2 - 8. CMM-Tagung 2015 - Innovative Feuchtemessung in Forschung und Praxis - Material - Prozesse - Systeme CY - Karlsruhe, Germany DA - 07.10.2015 KW - Estrich KW - Feuchtemessung KW - Radar KW - Hydratation KW - Baustoffe KW - Feuchte KW - Zerstörungsfreie Prüfung KW - Kapazitive Methoden PY - 2015 N1 - Serientitel: Innovative Feuchtemessung in Forschung und Praxis – Series title: Innovative Feuchtemessung in Forschung und Praxis VL - 8 SP - 79 EP - 91 AN - OPUS4-34763 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Petrat, T. A1 - Graf, B. A1 - Gumenyuk, Andrey A1 - Rethmeier, Michael T1 - Laser-Pulver-Auftragschweißen zum additiven Aufbau komplexer Formen N2 - Das Laser-Pulver-Auftragschweißen als additives Fertigungsverfahren ermöglicht einen endformnahen Aufbau von Bauteilen. Ein Zielkonflikt besteht zwischen der Forderung nach hoher Aufbaurate und hoher Endformnähe, welcher von der Schweißraupengröße wesentlich beeinflusst wird. In dieser Veröffentlichung wird das Laser-Pulver-Auftragschweißen eingesetzt, um komplexe Formen additiv aufzubauen. Am Beispiel eines Tannenbaumprofiles werden unterschiedliche Einflussfaktoren dargestellt. Dazu gehören die Raupengeometrie, die Überlappung einzelner Raupen, die Verwendung unterschiedlicher Aufbaustrategien und die Teilung des Gesamtkörpers in Teilkörper. Der Zielkonflikt wird durch die Herstellung von Probekörpern mit unterschiedlichen Steigungswinkeln an den Seitenflächen verdeutlicht. Die Ergebnisse zeigen eine verbesserte Endformnähe in Bereichen flacher Steigung beim Einsatz kleiner Schweißraupen. Im Vergleich dazu erlauben die Schweißparameter der großen Raupen eine 5-fach höhere Aufbaurate. Bei einer Raupenüberlappung kleiner und großer Raupengeometrien innerhalb einer Lage treten Anbindungsfehler auf. Strategien zur Behebung dieses Fehlers durch Anpassung der Schweißreihenfolge werden in dieser Veröffentlichung aufgezeigt. Diese Erfahrungen werden genutzt, um einen Gesamtkörper aus Teilkörpern unterschiedlicher Raupengeometrien zu fertigen. T2 - DVS Congress 2015 - Große Schweißtechnische Tagung CY - Nuremberg, Germany DA - 14.09.2015 PY - 2015 SN - 978-3-945023-46-4 N1 - Serientitel: DVS-Berichte – Series title: DVS-Berichte IS - 315 SP - 126 EP - 129 PB - DVS Media GmbH CY - Düsseldorf AN - OPUS4-34770 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wosniok, Aleksander A1 - Krebber, Katerina ED - Karabay, G. ED - Kara, S. T1 - Smart geosynthetics for structural health monitoring using fully distributed fiber optic sensors N2 - We report on the development of a complete system for structural health monitaring of large-scale geotechnical structures. The system uses Brillouin frequency domain analysis (BOFDA) for distributed measurement of strain and temperature along glass optical fibers (GOFs) by determining the so-called Brillouin frequency shift (BFS). ln a number of research activities we managed to optimize the BOFDA measurement setup regarding the spatial resolution and the accuracy of the measured quantities. Moreover, we realized a simultaneaus measurement of strain and temperature by using nonzero dispersion-shifted fibers (NZDSFs) with several multiple Brillouin scattering resonances. ln cooperation with our German and ltalian industry partners we finally succeeded in fabricating low-attenuation smart geosynthetics as a sensor component of a fully distributed Brillouin-based fiber optic monitaring system. T2 - 6th International Technical Textiles Congress CY - Izmir, Turkey DA - 14.10.2015 KW - Brillouin scattering KW - Distributed sensor KW - Fiberoptic sensor KW - Optical fiber KW - Structural health monitoring PY - 2015 SN - 978-975-441-448-6 SP - 215 EP - 218 PB - Meta Basim Pr. AN - OPUS4-34772 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seuthe, T. A1 - Grehn, M. A1 - Mermillod-Blondin, A. A1 - Bonse, Jörn A1 - Eberstein, M. T1 - Requirements on glasses for femtosecond-laser based micro-structuring N2 - In this work, glasses with systematically varied compositions were manufactured and irradiated by single Ti:sapphire fs-laserpulses (800 nm, 120 fs), focused at the surface and into the bulk of the glass materials. The samples were tested for their ablation threshold fluence as well as for structural changes using µ-Raman-spectroscopy. Correlations between the glass composition, the material-ablation on the glass surface and the permanent changes of the refractive index inside the glass volume after the irradiation by fs-laser pulses were obtained. The results show, that the structural modifications found at the surface of the glasses and inside its volume are closely related. However, while the ablation threshold fluence of the glass surface primarily depends on the glass dissociation energy, the permanent refractive index change inside the volume is rather determined by its ability for absorbing the fs-laser pulses and the subsequent relaxation processes. The results of this work provide some guidance on how the glass composition can be varied in order to optimize the fs-laser induced modification of dielectrics. T2 - 11th International Conference on Ceramic Interconnect & Ceramic Microsystems Technologies CY - Dresden, Germany DA - 20.04.2015 PY - 2015 SN - 978-1-5108-0456-2 DO - https://doi.org/10.4071/CICMT-TA24 SP - 47 EP - 53 PB - Curran CY - Red Hook, NY, USA AN - OPUS4-34755 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hübner, P. A1 - Zerbst, Uwe ED - Hütter, G. ED - Zybell, L. T1 - Fracture mechanics assessment of welded components at static loading N2 - Special aspects of welded components such as geometrical imperfections, inhomogeneity, strength mismatch and welding residual stresses have to be taken into account in a fracture mechanics analysis since they affect the crack driving force in the component as weil as the fracture resistance of the material. The treatment of components subjected to static loading is based on methods such as the European SINT AP procedure, which has been validated in a nurober of case studies. In the present paper the influence of strength mismatch and residual stresses on the fracture resistance and the assessment of a component are discussed. T2 - International symposium 'Recent trends in fracture and damage mechanics' CY - Freiberg/Sachsen, Germany DA - 24.09.2015 KW - Fracture mechanics KW - Weldments PY - 2015 SN - 978-3-319-21466-5 SP - Part II, 61 EP - 86 PB - Springer AN - OPUS4-34758 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Salg, Steffen A1 - Malow, Marcus A1 - Michael-Schulz, Heike T1 - Wie beeinflussen nicht-atmosphärische Bedingungen das Deflagrationsverhalten? N2 - Zur Bestimmung der Deflagrationsfähigkeit von energiereichen Stoffen/ Gemischen wurde zuletzt ein Vier-Liter-Autoklav vorgeschlagen, der im Vergleich zu den derzeit gängigen Prüfmethoden eine Reihe von Vorteilen bietet. In diesem Beitrag wird der Frage nachgegangen, wie nicht-atmosphärische Bedingungen das Deflagrationsverhalten beeinflussen. Zur Beantwortung dieser Frage wurden weitere Experimente im genannten Autoklaven und in einem kleineren Autoklaven durchgeführt. Im Wesentlichen lässt sich feststellen, dass der Druck im Probengefäß vor Versuchsbeginn, insbesondere reduzierter Ausgangsdruck < 1 bar Auswirkungen auf das Deflagrationsverhalten hat. Das Vorhandensein einer reinen Stickstoffatmosphäre hingegen, beeinflusst das Deflagrationsverhalten nicht. T2 - 12. Fachtagung Anlagen-, Arbeits- und Umweltsicherheit CY - Köthen, Germany DA - 05.11.2015 KW - Deflagration KW - Geschlossener Behälter KW - Autoklav KW - Nicht-atmosphärische Bedingungen PY - 2015 SN - 978-3-86011-091-1 SP - P12, 1 EP - 4 AN - OPUS4-34821 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Woydt, Mathias A1 - Mohrbacher, H. ED - Singh, D. ED - Salem, J. ED - Wang, J. ED - Kirihara, S. T1 - Hardmetals based on niobium carbide (NbC) versus casted NbC bearing MMCs N2 - Thc tribological behavior under dry sliding of a Fe3Al-NbC composite prepared by pyrometallurgical synthesis is compared to NbC-based hard metals bonded by cobalt or Fe3Al. The dry sliding wear resistance (0,1-7/10 m/s) of the present Fe3Al-NbC with 60% NbC was close to those known of NbC-based hard metals. No grain pull-outs or fragmentations of the NbC grains were seen in the wear tracks, as a metallurgical interphase was formed between matrix and NbC grains. T2 - 39th International conference on advanced ceramics and composites CY - Daytona Beach, FL, USA DA - 25.01.2015 PY - 2015 SN - 978-1-119-21128-0 SP - 87 EP - 92 PB - Wiley AN - OPUS4-34888 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Baier, Jennifa A1 - Beck, Uwe A1 - Hidde, Gundula A1 - Hielscher, Stefan A1 - Lange, Thorid A1 - Mix, Renate T1 - Plasmagestützte Oberflächenfunktionalisierung von Polypropylen (PP) N2 - Polypropylen (PP) ist als Niedrigenergie-Polymer ohne nass- und plasmachemische Vorbehandlung weder haftfest zu beschichten noch verbundfest zu kleben. Typische Haft- bzw. Klebfestigkeiten liegen für die unbehandelte Polymeroberfläche bei maximal 0,5 MPa. Hinzu kommt, dass bei der Bestimmung von Haft- und Klebfestigkeiten der unmodifizierten Oberfläche mit großen Streuungen zu rechnen ist, die bezogen auf die Spannweite durchaus einem Faktor 5 entsprechen können. Generell besteht bei Prüfung der Haftfestigkeit mittels Stirnabzugsversuch und bei der Prüfung der Klebfestigkeit die Notwendigkeit eines statistisch validierten Herangehens. Hierzu sind zeitaufwändige Ein-Proben-Klebungen und -Prüfungen nur eingeschränkt geeignet. Zudem ist, insbesondere für geringe Haft- bzw. Klebfestigkeiten, ein querkraftfreies Prüfen Grundvoraussetzung. Im vorliegenden Beitrag werden verschiedenartige plasmagestützte Oberflächenfunktionalisierungen von PP sowie das Mehr-Proben-Konzept zur Klebung/Prüfung von bis zu acht Proben vorgestellt. Dazu werden ein BAM-Funktionsmuster einer Mehr-Proben-Kleb-Vorrichtung und eine kommerzielle analytische Zentrifuge zum Prüfen verwendet. T2 - 24. Workshop des Anwenderkreises Atmosphärendruckplasma "Haftung durch Oberflächenfunktionalisierung" CY - Erfurt, Germany DA - 11.11.2015 KW - Plasmamodifizierung KW - Polypropylen KW - Haftfestigkeit KW - Klebfestigkeit KW - Mehr-Proben-Kleben/-Prüfen PY - 2015 SP - 1 EP - 6 PB - Anwenderkreis Atmosphärendruckplasma CY - Jena AN - OPUS4-34838 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weise, Frank A1 - Voland, Katja A1 - Meng, Birgit ED - Ludwig, H.-M. T1 - AKR unter kombinierten Einwirkungen - Rissbildungs- und Transportmechanismen N2 - ln den letzten Jahren sind im deutschen Bundesautobahnnetz verstärkt Schäden an Betonfahrbahndecken aufgetreten, die mit einer Alkali-Kieselsäure-Reaktion (AKR) in Verbindung gebracht werden. Die damit einhergehende oft drastische Reduzierung der Nutzungsdauer der Betonfahrbahndecke führte zu einer starken Intensivierung der Forschung auf diesem Gebiet. Zentraler Forschungsgegenstand war bisher neben der Suche nach geeigneten präventiven betontechnologischen Maßnahmen vor allem die Entwicklung performanceorientierter Prüfverfahren zur AKR-Prävention. Dabei wurden insbesondere die klimatischen Einwirkungen auf die Betonfahrbahndecke und der externe Alkalieintrag zeitraffend simuliert. Die zusätzlich interagierenden mechanischen Einwirkungen aus dem Verkehr fanden bisher keine Berücksichtigung. Vor diesem Hintergrund verfolgt die 2011 eingerichtete und 2015 um weitere drei Jahre verlängerte DFG-Forschergruppe 1498 u. a. das Ziel, den Einfluss einer mechanisch induzierten Vorschädigung (Ermüdungsbeanspruchung) auf den AKR-Schädigungsprozess zu klären. Die hierfür erforderliche Beschreibung der vielfältigen interagierenden Schädigungs- und Transportprozesse erfordert eine enge Verknüpfung von Experimenten mit einer mehrskaligen Modellierung. Die experimentelle Basis bildet die mechanische Vorschädigung (Ermüdung) großformatiger Balken aus einem Fahrbahndeckenbeton mit einem erhöhten AKR-Schädigungspotenzial. Aus diesen Balken werden nach der Ermüdungsbeanspruchung kleinformatige Probekörper gewonnen, an denen die Auswirkungen der mechanischen Vorschädigung auf das Betongefüge und die interagierenden Transport- und Schädigungsprozesse analysiert werden. Das Teilprojekt der SAM hat in diesem Kontext die Aufgabe, ganzheitlich die Rissbildungsprozesse und den interagierenden Eintrag bzw. Auslaugung der Alkalien von der mechanisch induzierten Vorschädigung bis zum AKR-Schädigungsprozess in enger Abstimmung mit den Forschungspartnern zu untersuchen. Den Schwerpunkt dieses Beitrags bildet die Charakterisierung der Rissbildungsprozesse durch die mechanische Vorschädigung und ihrer Auswirkungen auf die interagierenden Transportprozesse. Das schließt die Vorstellung der hierfür angewandten innovative Prüftechniken und Prüfmethodologien ein. T2 - 19. Ibausil - Internationale Baustofftagung CY - Weimar, Germany DA - 16.09.2015 KW - Betonfahrdecke KW - Ermüdung KW - Transportprozess KW - Ultraschall KW - Schallemissionsanalyse KW - Computertomografie KW - Laser-induced breakldown spectroscopy PY - 2015 SN - 978-3-00-050225-5 VL - 1 SP - 1 - 1461 EP - 1 - 1471 AN - OPUS4-34864 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Woydt, Mathias A1 - Mohrbacher, H. T1 - The background for the use of hardmetals and MMCs based on niobium carbide (NbC) as cutting tools and for wear resistant tribosystems N2 - In this present study, the mechanical properties (strength, hardness, moduli) and the dry sliding properties of stoichiometric and sub-stoichiometric NbC were compared. Microhardness and elastic properties of NbC depend from the C/Nb ratio, because the binary phase diagram Nb-C shows a region of homogeneity of NbCx of 0,72≤ x ≤1.0. At RT, hard metals of stoichiometric NbC have an elastic modulus E of ~440 GPa, those of substochiometric NbC0,88 an E of 405 GPa. The hot hardness of sub-stoichiometric NbC is above 600°C higher than of WC. The dry sliding wear resistance (0,1-7/10 m/s) of the present Fe3Al-NbC0,94 with ~61 vol.-% NbC as hard phase was close to those known of NbC-based hard metals. No grain pull-outs or fragmentations of the NbC grains were seen in the wear tracks of the Fe3Al-NbC composite (MMC), as a metallurgical interphase was formed between matrix and NbC grains. Stoichiometric and sub-stoichiometric niobium carbides have at RT and 400°C under dry sliding a prone intrinsic wear resistance more or less independent from sliding speed, either as hardmetal or as hard phase in metal matrix composite, associated with an exceptional high load carrying capacity. T2 - 3rd International Conference on Stone and Concrete Machining (ICSCM) CY - Bochum, Germany DA - 02.11.2015 KW - NbC KW - Niobium carbide KW - Cobalt KW - Fe3Al KW - Hardmetals KW - Metal matrix composite KW - Wear resistance KW - Cutting KW - Milling PY - 2015 SN - 978-3-943063-20-2 SP - 199 EP - 207 PB - Ruhr-Universität Bochum CY - Bochum AN - OPUS4-34846 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Neumann, Patrick P. A1 - Bartholmai, Matthias A1 - Lazik, D. T1 - Near real-time reconstruction of 2D soil gas distribution from a regular network of linear gas sensors N2 - A monitoring method is introduced that creates, in near real-time, two-dimensional (2D) maps of the soil gas distribution. The method combines linear gas sensing technology for in-situ monitoring of gases in soil with the mapping capabilities of Computed Tomography (CT) to reconstruct spatial and temporal resolved gas distribution maps. A weighted iterative algebraic reconstruction method based on Maximum Likelihood with Expectation Maximization (MLEM) in combination with a source-by-source reconstruction approach is introduced that works with a sparse setup of orthogonally-aligned linear gas sensors. The reconstruction method successfully reduces artifact production, especially when multiple gas sources are present, allowing the discrimination between true and non-existing so-called ghost source locations. A first experimental test indicates the high potential of the proposed method for, e.g., rapid gas leak localization. T2 - IEEE Sensors 2015 CY - Busan, South Korea DA - 01.11.2015 KW - Distributed linear sensor KW - Membrane-based gas sensing KW - Subsurface monitoring KW - Gas storage areas KW - Computed tomography PY - 2015 SN - 978-1-4799-8202-8 SN - 1930-0395 SP - 1550 EP - 1553 PB - IEEE AN - OPUS4-34849 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kluge, Martin A1 - Kreißig, Michael A1 - Liebner, Christian A1 - Spoormaker, T. T1 - Identifizierung von sicherheitstechnisch gefährlichen Bedingungen für schlagartige Kompressionsvorgänge chemisch instabiler Gase im industriellen Maßstab N2 - Tetrafluorethen wird von der Polymerindustrie seit Jahrzenten als monomeres Ausgangsmaterial sowohl für die Herstellung von Polymeren (PTFE) als auch für Kopolymere (PCTFE) eingesetzt. Aufgrund seiner Eigenschaft als chemisch instabiles Gas kann TFE auch ohne Luftsauerstoff oder einen anderen Oxydator explosionsartig zerfallen. Nach der Initiierung des Zerfalls kann dieser unter bestimmten Bedingungen aufgrund des exothermen Reaktionsverhaltens sich selbstständig in Apparaten und Rohrleitungen ausbreiten. Dies geht aufgrund der freigesetzten Reaktionsenthalpie mit einem schlagartigen Anstieg von Druck und Temperatur einher, was zu erheblichen Belastungen der Materialien bis hin zum Versagen und Bruch und möglichen Folgeschäden einschließlich Personenschäden führen kann und in der Vergangenheit bereits mehrfach geführt hat. Besonders nach Wartungsarbeiten besteht die Gefahr, dass Teilabschnitte im Rohrleitungssystem mit TFE, Stickstoff oder Luft gefüllt sind mit Drücken in einem Bereich zwischen technischem Vakuum und atmosphärischem Druck wohingegen angrenzende Rohrabschnitte oder Behälter immer noch TFE bei Betriebsdrücken bis 32 bar enthalten können. Dabei sind die Abschnitte in der Praxis häufig durch Kugelhähne voneinander getrennt, die aufgrund ihrer Öffnungscharakteristik bereits bei geringen Betätigungswinkeln eine große Querschnittsfreigabe für die Strömung im Rohr ermöglichen. Dadurch können schlagartige Kompressionsvorgänge des Gases im Niederdruckbereich ermöglicht werden, die allein aufgrund der thermodynamischen Zustandsänderung zu einer erheblichen Temperaturerhöhung führen und im schlimmsten Fall zur Initiierung der Zerfallsreaktion führen können. Es wird erstmalig ein Versuchsaufbau im Industriemaßstab, der einer explosionsartigen Zerfallsreaktion von TFE standhalten kann. Zahlreiche Sicherheitskonzepte einschließlich diverser Berstscheibenkonfigurationen als auch zeitgesteuerte Schnellschlussventile wurden eingehend untersucht und bewertet, um die optimale Versuchskonfiguration für bestmögliche Reproduzierbarkeit festzulegen. Es fand eine systematische Untersuchung der schlagartigen Kompression der Systeme Luft/Luft, TFE/Luft, TFE/TFE und TFE/N2 statt. In der Hochdrucksektion wurden Drücke bis 30 bar realisiert und im Niederdrucksektor konnten Anfangsdrücke im Bereich weniger Millibar bis hin zu Atmosphärendruck eingestellt werden. Als Hauptergebnis wurde ein „Hazard diagram" erstellt, mit dessen Hilfe die Zündwahrscheinlichkeit in Abhängigkeit vom Hochdruck und Niederdruck abgeschätzt werden kann. Gefährliche Bedingungen in Rohrleitungen können dadurch auf einfachem Weg identifiziert werden. Als Referenzsystem zur Beurteilung der maximal erreichbaren nicht reaktiven Kompressionstemperaturen wurde Luft/Luft verwendet. Die damit ermittelten Daten dienten zur Bewertung von zusätzlichen exothermen Effekten, wie sie etwa bei Vorreaktion des TFE im Falle einer Dimerisierung auftreten können. Entgegen der ursprünglichen Annahme konnten die Systeme TFE/Stickstoff und TFE/TFE im verwendeten Aufbau nicht durch Kompressionsvorgänge gezündet werden. T2 - 12. Fachtagung Anlagen-, Arbeits- und Umweltsicherheit CY - Köthen, Germany DA - 05.11.2015 KW - Tetrafluoroethen KW - Zerfall KW - Selbstentzündung KW - Adiabate Kompression PY - 2015 SN - 978-3-86011-091-1 SP - 1 EP - 10 AN - OPUS4-34852 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pfeffer, D. A1 - Scholz, Christian A1 - Belly, C. A1 - Wäsche, Rolf A1 - Schlaak, H.F. A1 - Pott, P.P. T1 - Influence of the actuation waveform on the performance of piezoelectric stick-slip actuators N2 - Performance and efficiency of piezo-electric stick-slip actuators are dependent on the waveform of the electrical actuation of the piezo-stack. This paper compares between a conventional saw-tooth actuation with two waveforms that feature softer acceleration in order to minimize the duration of the slip-phase. It is shown that the proposed waveforms increase both maximum mechanical output power (by 43%) and overall efficiency (by 25%) of the examined actuator. T2 - IKMT 2015 - Innovative Klein- und Mikroantriebstechnik CY - Köln, Germany DA - 14.09.2015 PY - 2015 SN - 978-3-8007-4072-7 N1 - Serientitel: ETG-Fachbericht – Series title: ETG-Fachbericht VL - 146 SP - 100 EP - 104 AN - OPUS4-34883 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Woydt, Mathias A1 - Mohrbacher, H. T1 - Influence of stoichiometry and processing on the tribological profile of hardmetals based on niobium carbide (NbC) N2 - The tribological behavior under dry sliding of a Fe3Al-NbC composite prepared by pyro-metallurgical synthesis is compared to different SPS sintered NbC-based hardmetals bonded by cobalt or Fe3AI. The dry sliding wear resistance (0. 1-7 /10 m/s) of the present Fe3Al-NbC with -60 % NbC was close to those known ofNbC-based hard metals. No grain pull-outs or fragmentations of the NbC grains were seen in the wear tracks of the Fe3Al-NbC composite, as a metallurgical interphase was formed between matrix and NbC grains. The physical prope1ties of melt grown NbC match those known from powder metallurgically sintered NbC using powders converted from Nb205. T2 - International conference on powder metallurgy & particulate materials 2015 CY - San Diego, USA DA - 17.05.2015 PY - 2015 SN - 978-1-943694-01-3 SP - 08-83 EP - 08-91 CY - Princeton, NJ, USA AN - OPUS4-34884 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Knechtel, Sophie A1 - Schmidt, Simon A1 - Mishra, K. B. A1 - Wehrstedt, Klaus-Dieter T1 - Modellierung der Hauptbrandszenarien von flüssigem Wasserstoff (LH2) mittels CFD N2 - Die sichere Lagerung und der Transport von Flüssigwasserstoff (LH2) verlangen nach verlässlichen Abschätzungen möglicher Risiken durch Feuer oder Explosion. Aufgrund des breiten Explosionsbereichs (4 Vol.-% - 74 Vol.-%) reagiert Wasserstoff sehr schnell und produziert hohe Flammentemperaturen. Da Wasserstoffflammen ruß- bzw. farblos sind, ist Wärmestrahlung im Fernfeld kein Risikofaktor. Allerdings stellen die hohe lokale Wärmestrahlung und die nicht sichtbaren Flammen eine Gefahr für Menschen und Infrastruktur in der Nähe dar. Es ist daher notwendig die Gefahren von LH2-Feuern sorgfältig zu bewerten. Einerseits sind experimentelle Untersuchungen verschiedener Szenarien teuer, andererseits können sie teilweise auch praktisch nicht durchführbar sein. Numerische Simulationen dieser Szenarien können ein Ausweg aus diesem Problem sein. In der vorliegenden Arbeit wird ein solcher Ansatz genutzt, um große Brandszenarien mit LH2 mittels CFD (Computational Fluid Dynamics) zu modellieren und so die notwendigen Sicherheitsabstände abzuschätzen. Der Fokus liegt dabei auf der Simulation von Jet- und Pool-Feuerszenarien mit einem kommerziellen CFD-Code (Ansys CFX). Die benötigten geometrischen Modelle werden für Jet- und Pool-Feuer erstellt und mit den nötigen Randbedingungen implementiert. Wichtige Submodelle für chemische Reaktionen (Einschritt- und detaillierte Modelle), Verbrennung (Eddy-Dissipation- und Flamelet-Modell) und Strahlung (Discrete-Transfer-Modell) werden genutzt. Die maximal simulierten Flammentemperaturen liegen bei ~2100 K für Jet-Feuer und ~2300 K für Pool-Feuer. Um Aussagen zu thermischen Sicherheitsabständen zu treffen, wurden die Spezifischen Ausstrahlungen (SEP) ermittelt und anschließend entsprechende Positionsfaktoren gewählt, um verlässliche Sicherheitsabstände zu berechnen. Je nach Bedarf können CFD-Modelle sowohl für qualitative als auch für quantitative Risikobewertungen von LH2-Großbränden genutzt werden. T2 - 12. Fachtagung Anlagen-, Arbeits- und Umweltsicherheit CY - Köthen, Germany DA - 05.11.2015 KW - Flüssigwasserstoff KW - Großbrand KW - Poolfeuer KW - Jet-Feuer KW - CFD KW - Sicherheitsabstand PY - 2015 SN - 978-3-86011-091-1 SP - Paper P-11, 1 EP - 8 AN - OPUS4-34827 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Helmecke, E. A1 - Fleßner, M. A1 - Kaufmann, M. A1 - Staude, Andreas A1 - Hausotte, T. T1 - Numerical measurement uncertainty determination for dimensional measurements of microparts with CT N2 - Up to now, the only standardized method to determine the measurement uncertainty for computed tomography (CT) is to use calibrated workpieces as specified in the Guideline VDI/VDE 2630 Part 2.1. This paper discusses a promising numerical method for uncertainty determination with help of a virtual metrological CT (VMCT). It gives an explanation of the adjustments, the input parameters and the execution of the simulation. Furthermore, it discusses the first results of uncertainty determination compared to the method of using calibrated workpieces with the aid of two example cases. T2 - 6th Conference on Industrial Computed Tomography (iCT) CY - Wels, Austria DA - 09.02.2016 KW - simulation KW - Simulation KW - Computertomographie KW - Dimensionelle Metrologie KW - Normung KW - numerische Messunsicherheitsbestimmung KW - computed tomography KW - dimensional metrology KW - standardization KW - numerical uncertainty determination PY - 2016 UR - http://www.ndt.net/article/ctc2016/papers/ICT2016_paper_id17.pdf SP - Paper ID17, 1 EP - 7 AN - OPUS4-35481 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Falkenberg, Rainer T1 - Simulation von Rißwachstum durch ein thermodynamisch konsistentes Phasenfeldmodell N2 - Durch ein thermodynamisch konsistentes Phasenfeldmodell kann die Rißinitiierung sowie das Rißwachstum in einem spröden Material mit Hilfe der Finite-Elemente-Methode simuliert werden. Ein diskreter scharfer Riß wird durch einen Regularisierungsansatz in ein Phasenfeld überführt, das einen kontinuierlichen Übergang zwischen Riß und Restmaterial abbildet. Modelle von C(T) - Bruchmechanikproben konnten unter monoton wachsender Belastung simuliert werden. Die Ergebnisse konnten mit analytischen Ergebnissen der linear-elastischen Bruchmechanik verglichen werden. Ablenkungen des Rißpfades konnten durch Modelle von gelochten Proben simuliert werden. An dem Modell eines Dreipunktbiegeversuchs konnte die Rißinitiierung demonstriert werden. Die Kenntnis und Modellierung eines vordefinierten Rißpfades ist bei Verwendung dieses Modells nicht erforderlich, was insbesondere zur Untersuchung von komplexen Rißpfaden von Vorteil sein kann. N2 - Crack initiation and propagation in a brittle material is modeled in the finite-element-framework by an extended thermodynamical phase field formulation. The sharp crack discontinuity is transferred into a degradation phase field by a regularisation that ensures a continous transition between crack and residual material. The model of a C(T)-specimen under monotonic increasing load was simulated. The results were compared with analytical results of linear-elastic fracture mechanics. Crack kinking was simulated on a specimen with holes. Crack initiation was studied one a model of a three-point bending specimen. The knowledge and modeling of a predefined crack path is not required with the application of this model and provides the ability to calculate complex crack topologies. T2 - 48. Tagung des DVM-Arbeitskreises Bruchmechanik und Bauteilsicherheit, Bruchmechanische Werkstoff- und Bauteilbewertung: Beanspruchungsanalyse, Prüfmethoden und Anwendungen CY - Freiburg im Breisgau; Germany DA - 16.02.2016 KW - Finite-Elemente-Methode KW - finite-element-method KW - Rißwachstum KW - Rißinitiierung KW - Phasenfeldmodell KW - Crack growth KW - crack initiation KW - phase field model PY - 2016 SN - 2366-4797 VL - DVM Bericht 248 SP - 41 EP - 50 CY - Berlin AN - OPUS4-35483 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gleis, Markus A1 - Gehrmann, Hans-Joachim A1 - Simon, Franz-Georg T1 - VDI-Richtlinie 3925 – Anwendung auf zwei Fallbeispiele N2 - Die VDI-Richtlinie 3925 entstand aus Diskussionen und Fragestellungen, die sich aus der Anwendung unterschiedlichster Methoden zur Bewertung verschiedener Verfahrenskonzepten aus dem Bereich der Abfallbehandlung ergeben haben. Je nach nachdem, wo der Focus der vorzunehmenden Bewertung liegt, wird sich die Methodik an diese Ziele anpassen oder - falls es die entsprechende Methodik noch nicht geben sollte - sich die Fragestellung anpassen müssen. T2 - ProcessNet Jahrestreffen CY - Frankfurt/Main DA - 23.02.2016 KW - Wirkungsgrad KW - Exergie KW - Abfallbehandlung KW - Ökobilanz PY - 2016 SP - 25 EP - 26 PB - ProcessNet CY - Frankfurt/Main AN - OPUS4-35506 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Simon, Franz-Georg A1 - Holm, Olaf T1 - Reduction of natural resource use by improving resource efficiency N2 - Improving resource efficiency at the end-of-life stage is illustrated in this paper by the example of materials recovery from waste, here from residues out of municipal solid waste incineration (MSWI). With mechanical treatment valuable materials like ferrous and non-ferrous metals and secondary construction material can be extracted from MSWI bottom ash. The potential contribution on the resource efficiency will be discussed. T2 - 12th International Conference on Ecomaterials CY - Tainan, Taiwan DA - 08.11.2015 KW - secondary raw material KW - resource efficiency KW - raw material equivaltent KW - bottom ash PY - 2015 SP - 5 EP - 6 AN - OPUS4-35509 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thiel, Erik A1 - Kreutzbruck, M. A1 - Ziegler, Mathias T1 - Spatial and temporal control of thermal waves by using DMDs for interference based crack detection N2 - Active Thermography is a well-established non-destructive testing method and used to detect cracks, voids or material inhomogeneities. It is based on applying thermal energy to a samples’ surface whereas inner defects alter the nonstationary heat flow. Conventional excitation of a sample is hereby done spatially, either planar (e.g. using a lamp) or local (e.g. using a focused laser) and temporally, either pulsed or periodical. In this work we combine a high power laser with a Digital Micromirror Device (DMD) allowing us to merge all degrees of freedom to a spatially and temporally controlled heat source. This enables us to exploit the possibilities of coherent thermal wave shaping. Exciting periodically while controlling at the same time phase and amplitude of the illumination source induces – via Absorption at the sample’s surface - a defined thermal wave propagation through a sample. That means thermal waves can be controlled almost like acoustical or optical waves. However, in contrast to optical or acoustical waves, thermal waves are highly damped due to the diffusive character of the thermal heat flow and therefore limited in penetration depth in relation to the achievable resolution. Nevertheless, the coherence length of thermal waves can be chosen in the mmrange for modulation frequencies below 10 Hz which is perfectly met by DMD technology. This approach gives us the opportunity to transfer known technologies from wave shaping techniques to thermography methods. We will present experiments on spatial and temporal wave shaping, demonstrating interference based crack detection. T2 - Photonics West 2016, OPTO, 9761 CY - San Francisco, CA, USA DA - 15.02.2016 KW - Active thermography KW - Thermal wave KW - Spatial light modulation KW - Crack detection KW - DMD KW - DMD coupled laser PY - 2016 DO - https://doi.org/10.1117/12.2210918 SN - 0277-786X VL - 9761 SP - 97610N-1 EP - 97610N-13 AN - OPUS4-35587 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thöns, S. A1 - Schneider, Ronald A1 - Faber, M.H. ED - Haukaas, T. T1 - Quantification of the value of structural health monitoring information for fatigue deteriorating structural systems N2 - This paper addresses the quantification of the value of structural health monitoring (SHM) before its implementation for structural systems on the basis of its Value of Information (VoI). The value of SHM is calculated utilizing the Bayesian pre-posterior decision analysis modelling the structural life cycle performance, the integrity management and the structural risks. The relevance and precision of SHM information for the reduction of the structural system risks and the expected cost of the structural integrity management throughout the life cycle constitutes the value of SHM and is quantified with this framework. The approach is focused on fatigue deteriorating structural steel systems for which a continuous resistance deterioration formulation is introduced. In a case study, the value of SHM for load monitoring is calculated for a Daniels system subjected to fatigue deterioration. The influence of and the value of SHM in regard to the structural system risks and the integrity management is explicated and explained. The results are pointing to the importance of the consideration of the structural system risks for the quantification of the value of SHM. T2 - ICASP 12 - 12th International conference on applications of statistics and probability in civil engineering CY - Vancouver, Canada DA - 12.07.2015 PY - 2015 DO - https://doi.org/10.14288/1.0076284 SP - Paper 605, 1 EP - 8 AN - OPUS4-34332 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Busse, F. A1 - Heidrich, C. A1 - Kleine, M. A1 - Sander, C. A1 - Ünal, Murat T1 - BEGLARES II Protection and restoration of monumental concrete-glazing with cathodic protection systems N2 - Since the 1950's, art has been fascinated by concrete glazing. In countless buildings of the post-war period they determine the lighting effect of the space by its function as luminous walls. A peculiar kind of stained glass from partially filigree compositions of two such contrasting materials: delicate, luminous glass and rough, austere concrete. Artistically designed components, which are equipped with a range of stylistic subtleties. But even after o short time of exposure a whole catalogue of damage patterns has been revealed, which documents the decay processes, such as the carbonation initiated corrosion of reinforcement. Cathodic protection is already used in a wide range of repair of concrete structures. Taking into account technical and historical preservation requirements, this research project aims to transfer these techniques to the conservation of concrete-glazing under less health risk, cost and work effort. T2 - 9th Forum for the conservation and technology of historic stained-glass CY - Paris, France DA - 08.07.2015 KW - Concrete-glazing KW - Dalles de verres KW - Cathodic corrosion protection KW - Heritage KW - Restoration KW - Maintenance PY - 2015 SN - 978-2-9543731-1-9 SP - 82 EP - 90 AN - OPUS4-34286 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dutto, Paola A1 - Stickle, M.M. A1 - Manzanal, D. A1 - Hernán, A.Y. A1 - Pastor, M. ED - Onate, E. ED - Owen, D.R.J. ED - Peric, D. ED - Chiumenti, M. T1 - Modelling of propagation with SPH of 1966 Aberfan flowslide: special attention to the role of rheology and pore water pressure N2 - Landslides can cause major economic damage and a large number of casualities as it is possible to see from past events occurred all over the world. Being able to predict these kind of hazards would then suppose the achievement of great benefits. Here a model that combines a depth integrated description of the soil-pore fluid mixture together with a set of 1D models dealing with pore pressure evolution within the soil mass is presented. The mathematical model is based on the Biot-Zienkiewicz equations, from where a depth averaged model is derived. Concerning the material behaviour, the approach used is the one suggested by the Perzyna viscoplasticity, which has been extensively used in the past to model solid behaviour prior to failure. In this framework, a simple shear rheological model is derived, providing the basal friction needed in depth integrated models. The Smoothed Particle Hydrodynamics (SPH) has been the numerical technique chosen to spatially discretised the depth integrated equations of the mathematical model. The purpose of this work is to apply the SPH depth integrated numerical model, together with the sub-model that predicts the evolution of the pore water pressure inside the landslide, to simulate the propagation phase of the Aberfan flowslide occurred in 1966. T2 - COMPLAS XIII - 13th International conference on computational plasticity - Fundamentals and applications CY - Barcelona, Spain DA - 01.09.2015 KW - Numerical modelling KW - Smoothed particle hydrodynamics KW - SPH KW - Fluidised geomaterials KW - Aberfan flowslide PY - 2015 UR - http://congress.cimne.com/complas2015/frontal/doc/EbookComplas2015.pdf SN - 978-84-944244-6-5 SP - 151 EP - 161 AN - OPUS4-34290 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Smith, T. A1 - Lohrer, Christian T1 - Are shells "safety" distances "safe"? N2 - There is a wide variety of approaches across the world in determining appropriate “safety distances” for firework displays. Comparison of the different national approaches and distances for Shells derived from Shellcalc© highlights the variety and derivation of the “safety distances” adopted and these distances are related to the various failure modes of Shells that may affect the audience. In particular the effects of angled mortars and wind are compared and considered. It is not intended that this paper should encourage the maximum distances derived always to be adopted, but that an appreciation of the probabilities and hazards of various accident scenarios and therefore the risks involved be part of the decision making process for designers and commissioners of displays as well as enforcing authorities. T2 - 15th International symposium on fireworks CY - Bordeaux, France DA - 21.09.2015 KW - Display fireworks PY - 2015 SN - 978-0-9867279-8-6 SP - 90 EP - 102 AN - OPUS4-34343 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Douet, Marianne A1 - Lohrer, Christian A1 - Kurth, Lutz A1 - Mücke, Olaf T1 - Safety related behavior of cylindrical shells N2 - The European Standard series EN 16261 consisting of four parts deals with the testing and assessment of display fireworks in order to satisfy the essential safety requirements of the Directive 2007/23/EC which have to be met before placing these articles on the EU market. The current Version of this Standard provides mortar dimension limits to be used for the assessment of burst heights of spherical Shells, but lacks corresponding provisions for cylindrical shells. The aim of this study was threefold: 1. To check whether the requirements for spherical shells would overlap with the ones for cylindrical shells, 2. To compare several test procedures for height measurements with each other to minimize the measurement uncertainty of the effect dimensions, and 3. To evaluate drift distances in order to check whether the current national provisions on safety distances for Professional fireworks displays need adaption during the implementation of the new European directive 2013/29/EU on pyrotechnics in German legislation. For this study, a large number of cylindrical shells was specifically manufactured to guarantee lull control on all relevant constructional aspects. These shells were designed with a smoke tracer and no burst Charge so that they would fall back to the ground in order to investigate their drift distances. Their gross mass corresponded to commercially available display shells, though, consisting of defined inert substances inside the shell. The following Parameters were varied in this study: caliber (75 mm, 100 mm, 150 mm), shell length per caliber (single and double length), lift Charge (hard and soft burst effect), mortar length per caliber (short and long). In total, more than 120 shells were manufactured and tested. Results show a good application of the proposed test procedures regarding the mortar dimensions given in the Standard series for cylindrical shells as well. The following test procedures were part of this study: Radar Doppler System, video grammetric System, universal surveying instruments, and mortar internal pressure measurements. Observed drift distances in relation to the caliber and effect heights are discussed and assessed. T2 - 15th International symposium on fireworks CY - Bordeaux, France DA - 21.09.2015 KW - Radar-Doppler KW - Height measurements KW - Drift effects KW - Safety distances PY - 2015 SN - 978-0-9867279-8-6 SP - 104 EP - 122 AN - OPUS4-34344 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Trubiroha, P. A1 - Geburtig, Anja A1 - Wachtendorf, Volker ED - Reichert, T. T1 - On the yet unsolved problem of the determination of precise surface temperatures of specimens exposed to natural and artificial weathering N2 - The surface temperature of test specimens exposed to natural and artificial solar radiation are roughly ascertained with black standard thermometers BST and white standard thermometers WST. For the calibration of these thermometers a new European Standard prEN 16465 was published in 2015, describing the well-known contact method and a new contactless method with a pyrometer. It can be confirmed that the temperature calibrations according to the two methods provide different calibration results which are not interchangeable (which is already stated in the scope of this standard). The described contactless method to determine the surface temperature 'under radiation load' results in clearly too high temperatures. This paper tries to highlighting the reasons. T2 - 7th European weathering symposium - Natural and artificial ageing of polymers CY - Naples, Italy DA - 16.09.2015 PY - 2015 SN - 978-3-9816286-6-1 N1 - Serientitel: CEEES Publication – Series title: CEEES Publication IS - 17 SP - 23 EP - 36 AN - OPUS4-34351 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Goedecke, Thomas A1 - Wachtendorf, Volker ED - Reichert, T. T1 - A new irradiation device for medium scale plastic products N2 - A new irradiation device for the exposure of plastic products is presented. Developed in the BAM division 3.1 "Dangerous Goods Packaging" it can be used for artificial UV irradiation of plastic Containers filled with hazardous liquids. Present regulations and tests only investigate the exposure effects of UV and of media separately, but as the damaging effect is expected to be synergistic for at least some media, a combined test was looked for. A chamber of 60 cm by 60 cm base area and 1 m height gives space for up to 40 cm wide objects. Two fluorescent UV lamp arrays are arranged on opposite walls, separated from the chamber by quartz glass panes. By continuously rotating the exposure object by means of a rotary disc that the object is placed on, spatial irradiation homogeneity is achieved over the exposure duration. The spectral irradiance of the chosen UVA 340 nm lamps gives the best match of global solar radiation in the short wavelength ränge. The close arrangement of the UVA lamps (15 each side) results in 60 W m'2 UV irradiance. Constant temperature is adjusted to typically 40 °C by the control of the fan speed. This temperature is chosen, as it is the required temperature for three week storage of filled polyethylene Containers, for proving Chemical compatibility in the field of dangerous goods. To ensure homogeneity, an interiorfan provides for air circulation. T2 - 7th European weathering symposium - Natural and artificial ageing of polymers CY - Naples, Italy DA - 16.09.2015 KW - Weathering KW - UV irradiation PY - 2015 SN - 978-3-9816286-6-1 N1 - Serientitel: CEEES Publication – Series title: CEEES Publication IS - 17 SP - 91 EP - 96 AN - OPUS4-34353 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin A1 - Lehmann, Jens A1 - Burkert, Andreas T1 - The KorroPad - A novel test method for assessing the pitting corrosion susceptibility of stainless steel surfaces N2 - Pitting corrosion is one of the most common mechanisms of local passivity breakdown on stainless steels. Electrochemical methods have preferentially been applied for the evaluation of pitting corrosion resistance of stainless steels in laboratory. Nevertheless, some of them are not reliable enough and in general the application of electrochemical methods in the field becomes difficult because of a required deep understanding of corrosion phenomena and measurement technology. A new approach for the evaluation of the pitting corrosion susceptibility of stainless Steel surfaces in the laboratory as well as in the field is frequently demanded by representatives of the metalworking industry. Therefore, the KorroPad-test was invented and patented as part of a research project at the BAM Federal Institute for Materials Research and Testing in Germany. T2 - EUROCORR 2015 - European corrosion congress CY - Graz, Austria DA - 06.09.2015 KW - KorroPad KW - Pitting corrosion KW - Stainless steel PY - 2015 SP - Paper 5_730, 1 AN - OPUS4-34297 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wu, Cheng-Chieh A1 - Weisbrich, S. A1 - Neitzel, F. T1 - Inverse finite element adjustment of material parameters from integrated analysis of displacement field measurement N2 - The integration of finite element method (FEM) into the least-squares adjustment presented in [1] is further extended for a joint evaluation of an elastostatic model and displacement field measurement. For linear solids which obey the HOOKE's law, the material parameters determination from measurements is being examined. In many literature, see for example [2], parameters are iteratively tuned until the computed FEM results are in accordance with the measurements. In contrast to these debatable approaches, we follow a rigorous and direct method. The “classical” FEM procedure starts with known material constants and ends up with computed fields such as dis-placement or temperature field. We present a method to invert the FEM procedure using the most general least-squares adjustment – the GAUSS-HELMERT Model (GHM). From given fields, the material parameters are directly calculated. T2 - 32nd Danubia-Adria Symposium on Advances in Experimental Mechanics CY - Stary Smokovec, Slovakia DA - 22.09.2015 PY - 2015 AN - OPUS4-34369 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kind, Thomas A1 - Trela, Christiane A1 - Schubert, Marcus A1 - Wöstmann, Jens ED - Lambot, S. ED - Giannopoulos, A. ED - Pajewski, L. ED - André, F. ED - Slob, E. ED - Craeye, C. T1 - Aggregates scattering of GPR waves in concrete N2 - Time slices of very dense GPR measurements carried out at concrete with a real point distance of less than 10 mm in x and y direction show weak reflection patterns besides the strong reflections of reinforcements. A repetition of these measurements with the same local geometrical precision at the same specimen shows the same reflection pattem. We suppose that the heterogeneity of concrete given by aggregates (e.g. gravel, broken granite) causes local weak Scattering of the GPR waves and leads to reflection patterns in the GPR data. These reflection patterns can be explained by a Superposition of multiple scatterings of single aggregates. So far these reflection patterns have been not recognized in Standard time slices due to the large spacing (> 5 cm) between single profiles and because of the interpolation between the profiles. We investigate the characteristics of the volume scattering effects, caused by aggregates, at concrete blocks with two different grading curves. In a more general investigation we study the volume scattering of aggregates by using wooden boxes filled with only typical aggregates and an included defined reflector (metal plate). The thickness of the aggregate layer above the metal plate was varied between 20 cm and 40 cm. With a very dense measuring grid at the surface we are able to calculate the effective volume scattering and to analyze the distribution of the reflection amplitude of the included metal plate for different aggregate set-ups. Results of this study confirm that the weak reflection patterns in concrete can be explained by aggregate scattering and have a direct correlation to the penetration depth of GPR in concrete. T2 - GPR 2014 - 15th International conference on ground penetrating radar CY - Brussels, Belgium DA - 30.06.2014 KW - Aggregates KW - Volume scattering PY - 2014 UR - http://sites.uclouvain.be/GPR2014 SP - 933 EP - 938 AN - OPUS4-34576 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wiggenhauser, Herbert ED - Büyüköztürk, O. T1 - Automated NDE of structures with combined methods N2 - Non-Destructive Evaluation (NDE) of structures is complex due to the uniqueness of almost all structures and their sizes. A single NDT method typically is not sufficient to meet the testing requirements, which cover different areas, such as material and structural properties. Measuring geometrical properties require other test methods than e.g. the detection of corrosion. Automation has proven to be necessary for aquiring large amounts a of high quality data in a short time. Examples of succesful method combinations from different areas of non-destructive testing in civil engineering are briefly described and their application is shown. Some of the examples also include automated inspection. T2 - International Symposium on Nondestructive Testing of Materials and Structures CY - Istanbul, Turkey DA - 15.05.2011 KW - Zerstörungsfreie Prüfung KW - Automatisierung KW - Inspektion PY - 2013 SN - 978-94-007-0722-1 DO - https://doi.org/10.1007/978-94-007-0723-8_107 N1 - Serientitel: RILEM bookseries – Series title: RILEM bookseries IS - 6 SP - 753 EP - 760 PB - Springer CY - Dordrecht AN - OPUS4-34609 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Qiao, Linan A1 - Zencker, Uwe A1 - Völzke, Holger ED - Brandt, A. M. ED - Olek, J. ED - Glinicki, M. A. ED - Leung, C.K.Y. ED - Lis, J. T1 - Crushable foam model with pressure and stress-triaxiality dependent damage mechanisms for damping concrete N2 - Damping concrete with high energy absorption capability consists of a cement matrix with embedded small polystyrene balls and is investigated experimentally and numerically under high static compression with and without clamping. A material model is derived which describes the fundamental effects of damping concrete like non-linear elastic-plastic behaviour, volume change, volume strain dependent hardening as well as shear failure with an adequate description of damage initiation and evolution. The suggested material model is validated by simulation of penetration tests. T2 - BMC-11, International Symposium on Brittle Matrix Composites CY - Warsaw, Poland DA - 28.09.2015 KW - Damping concrete KW - Impact load KW - Crushable foam material model KW - Damage PY - 2015 SN - 978-83-89687-96-8 SP - 269 EP - 277 PB - Inst Fundamental Technological Research, Polish Acad Sciences CY - Warschau AN - OPUS4-34613 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin A1 - Reinemann, S. T1 - Electrochemical investigations regarding the influence of deformation-induced martensite on the corrosion behaviour of austenitic stainless steels N2 - Contents of deformation-induced martensite in the lattice structure of austenitic stainless steels lead to an either beneficial or detrimental change of mechanical and magnetic properties depending on the prospective application. Whereas these changes are well-known and investigated widely the influence of deformation-induced martensite on the corrosion behaviour is frequently an issue of scientific discussions. There are opposing opinions that depend on the type of corrosion mechanism being investigated for example regarding pitting corrosion resistance in Chloride containing media. In it is stated that pitting resistance is not influenced by deformationinduced martensite while in it is discussed that more pitting occurs on martensitic structure. The same conflictive opinions appear regarding active dissolution in acidic media or intergranular corrosion. In addition, when having deeper insight into literature it can be concluded that even the type of test method, i. e. dynamic or static testing, has a big influence on the obtained results concerning the influence of martensite in austenitic stainless steels. T2 - EUROCORR 2015 - European corrosion congress CY - Graz, Austria DA - 06.09.2015 KW - Deformation-induced martensite KW - Stainless steel KW - Electrochemical investigations PY - 2015 SP - paper 5_776 AN - OPUS4-34617 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zerbst, Uwe A1 - Madia, Mauro T1 - Der Schwellenwert DKth als Auslegekriterium. Aktuelle Entwicklungen und Fragestellungen N2 - Bei der Bestimmung der Restlebensdauer zyklisch beanspruchter Bauteile kommt dem Schwellenwert für Ermüdungsrissausbreitung, K111, oft entscheidende Bedeutung zu. Dabei ist seine Anwendung weniger gesichert als bislang angenommen. Der Vortrag diskutiert Fragen der experimentellen Ermittlung des Schwellenwertes sowie seiner Anwendung auf Bauteile. Auf beiden Gebieten haben sich in den letzten Jahren Probleme ergeben, die bestehendes Wissen teilweise wieder in Frage stellen oder modifizieren. Im Beitrag diskutiert werden der Einfluss unterschiedlicher Rissschließmechanismen auf K111, Konsequenzen, die sich daraus hinsichtlich der Ermittlung und Übertragung des Kennwertes ergeben, sowie die Effekte von Einflussgrößen wie Spannungsverhältnis und Rissgröße, aber auch des Werkstoffgefüges und der damit korrelierten mechanischen Eigenschaften. T2 - 47. Tagung des DVM-Arbeitskreises Bruchvorgänge und Bauteilsicherheit - Bruchmechanische Werkstoff- und Bauteilbewertung: Beanspruchungsanalyse, Prüfmethoden und Anwendungen CY - Freiberg, Sachsen, Germany DA - 10.02.2015 PY - 2015 SN - 1616-4687 SP - 305 EP - 321 AN - OPUS4-34621 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fasano, A. A1 - Woyessa, G. A1 - Stajanca, Pavol A1 - Markos, C. A1 - Stefani, A. A1 - Nielsen, K. A1 - Rasmussen, H. K. A1 - Krebber, Katerina A1 - Bang, O. T1 - Production and characterization of polycarbonate microstructured polymer optical fiber bragg grating sensor N2 - We present the fabrication and characterization of a polycarbonate (PC) microstructured polymer optical fiber (mPOF) and the writing of a fiber Bragg grating (FBG) in it to obtain a polymer optical FBG sen-sor. The manufacturing process of the PC mPOF consists of multiple consecutive stages, such as casting of pol-ymer granulates into a solid rod, machining and drilling of a 3-ring hexagonal lattice of holes into it, and finally drawing into fiber. We demonstrate that the obtained PC mPOF is photosensitive and FBGs can be conveniently inscribed into it, thereby enabling FBG-based temperature and strain sensing. The PC optical fibers are for some applications an attractive alternative to conventional materials used in POF fabrication, such as polymethyl methacrylate (PMMA). In general, PC can be used at temperature up to 120 °C and breaks at considerably higher strains than PMMA. T2 - POF 2015 - 24th International conference on plastic optical fibers CY - Nürnberg, Germany DA - 22.09.2015 PY - 2015 SP - 64 EP - 67 AN - OPUS4-34587 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Miccoli, Lorenzo A1 - Fontana, Patrick A1 - Johansson, G. A1 - Zandi, K. A1 - Portal, Natalie Williams A1 - Müller, U. T1 - Numerical modelling of UHPC and TRC sandwich elements for building envelopes N2 - ln this paper a modelling approach is presented to reproduce the mechanical behaviour of sandwich panels via finite element analysis. Two types of panels were investigated in this scope of work. The first sandwich element was a textile reinforced concrete (TRC) panel with cellular lightweight concrete insulation and the second configuration was an ultra-high performances concrete (UHPC) panel with aerated autoclaved concrete insulation. The goal was to obtain a reliable numerical strategy that represents a reasonable compromise in terms of sufficient accuracy of the element characteristics and the computational costs. The results show the possibility of describing the composite action in a full sandwich panel. The achieved modelling approach will later be used for the optimization of TRC and UHPC panels in terms of minimizing the thickness, identifying the number and location of connectors, as well as evaluating varying anchorage Systems. T2 - IABSE conference - Structural engineering: Providing solutions to global challenges CY - Geneva, Switzerland DA - 23.09.2015 KW - Sandwich elements KW - Ultra-high performance concrete (UHPC) KW - Textile reinforced concrete (TRC) KW - Autoclaved aerated concrete (AAC) KW - Cellular lightweight concrete (CLC) KW - Finite element analysis (FEA) PY - 2015 SN - 978-3-85748-140-6 SP - 195 EP - 203 AN - OPUS4-34552 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, Frank A1 - Köppe, Enrico A1 - Daum, Werner T1 - Tracking deformation history in split Hopkinson pressure bar testing N2 - The stress vs. strain curve of materials is affected the rate of imposed straining. Among the methods for dynamic testing the technique known as 'split Hopkinson pressure bar' (SHPB) has evolved into the most widely used one to exert high-speed straining. The theory behind it comprises simple equations to compute stress and strain. The reliability of the strain analysis can be assessed by digital image correlation (DIC). The present results indicate that the visually observed strain is smaller than predicted by theory. T2 - 32nd Danubia-Adria Symposium on Advances in Experimental Mechanics CY - Starý Smokovec, Slovakia DA - 22.09.2015 KW - Split Hopkinson pressure bar (SHPB) KW - Digital image correlation (DIC) KW - Digitale Bildkorrelation (DIC) KW - Dynamic testing KW - Dynamische Tests KW - Stress-strain curve KW - Spannungs-Dehnungs-Kurve PY - 2015 SN - 978-80-554-1094-4 SP - 174 EP - 175 PB - University of Zilina, Slovakia CY - Zilina AN - OPUS4-35656 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst T1 - Levee inspection - geophysics between science, standards, reliability and budgets N2 - Numerous case histories show evidence that geophysical methods are valuable tools for levee inspection and monitoring. National and international standards and recommendations recommend the use of geophysics for a variety of tasks. However, in some cases reported have been flaws missed or false indications given. Due to the larger variety in type, size and construction of levees and the even larger variety of potential tasks and targets the success of geophysical surveys still pretty much depends on the available budget and the experience and capabilities of the clients and contractors involved. It is strongly recommended that all relevant parties agree on the detailed objectives of the survey, required accuracy and reliability of the results and any follow up measures. For the most common tasks more research and practical work using techniques as POD (probability of detection), which are well established in other fields of non-destructive testing, would be of benefit. T2 - SAGEEP 2016 CY - Denver, CO, USA DA - 20.03.2016 KW - Levee KW - Geophysics KW - Inspection PY - 2016 SP - paper levees 07, 1 EP - 4 AN - OPUS4-35705 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Merryweather, S. A1 - Zweifel, D. A1 - Woydt, Mathias ED - Franek, F. ED - Bartz, Wilfried J. ED - Pauschitz, A. ED - Vizintin, J. ED - Ciulli, E. ED - Crockett, R. T1 - Fuel economy of engine oils based on polyalkylene glycols N2 - The driver for automotive OEMs to work on alternative engine oils is the need for fuel economy and no adverse effect of the engine oil on the durability of particulate filters and catalysts. The alternative engine oils should for mid-term also comply with a positive environmental Profile. T2 - 3rd European Conference on Tribology and 4th Vienna International Conference on Nano-Technology CY - Vienna, Austria DA - 07.06.2011 KW - Biomotox KW - Head capacity KW - Fuel economy KW - Drain KW - Polyglycol KW - Polypropylene glycol KW - Polyalkylene glycol KW - Polybutylene glycol PY - 2011 SN - 978-3-901657-38-2 SP - 25 EP - 34 PB - MDH Media GesmbH CY - Wien AN - OPUS4-35671 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -