TY - CONF A1 - Vössing, Konrad A1 - Gaal, Mate A1 - Niederleithinger, Ernst T1 - Air-coupled ferroelectret ultrasonic transducers for nondestructive testing of wood in through transmission and reflection mode N2 - The necessity and demand for nondestructive testing of wood-based materials which can automatically scan huge areas of wood is increasing. Air-coupled ultrasound (ACU) is used to detect defects and damage without altering the structure permanently. Using through transmission it is possible to detect even small holes and missing adhesive. If only one side of an object is accessible the reflection mode is preferred at the expense of a reduced resolution and penetration depth. Novel ferroelectret transducers with a high signal-to-noise ratio (SNR) enable a high-precision structure recognition. The transducers made of cellular polypropylene (PP) are quite suitable for ACU testing due to their extremely low Young’s modulus and low density which result in a favorable acoustic impedance for the transmission of ultrasonic waves between the transducer and air. Thus, defects such as delamination, rot, and cracks can be detected. Promising results were obtained under laboratory conditions with frequencies from 90 kHz to 200 kHz. The advantage of these ACU transducers is that they do not require contact to the sample, are accurate, and cost effective. Ultrasonic quality assurance for Wood is an important attempt to increase the acceptance of wooden structures and towards sustainability in civil engineering in general. T2 - International Conference on Sustainable Materials, Systems and Structures CY - Rovinj, Croatia DA - 20.03.2019 KW - Air-coupled ultrasound KW - Cellular polypropylene KW - Wood KW - Nondestructive Testing KW - Defect detection PY - 2019 SP - 28 EP - 33 AN - OPUS4-47682 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst ED - Gabrijel, Ivan ED - Grosse, Christian ED - Skazlić, Marijan T1 - Ultrasonic monitoring of structural concrete elements N2 - Ultrasonic transmission measurements are used to monitor concrete elements mostly on a laboratory scale since decades. Recently, coda wave interferometry, a technique adapted from seismology, has been introduced to civil engineering experiments. It can be used to reveal subtle changes in concrete samples and even large construction elements without having a transducer directly at the location where the change is taking place. The methodology works best with embedded transducers to avoid coupling issues or excessive environmental influence. These transducers can be used for newly built and existing structures. Recently, large concrete beams have been equipped with a network of transducers and loaded until failure. Using code wave interferometry, it was possible to visualize stress fields and damaged areas. This paper gives an overview of the state of the art, recent results achieved at BAM and a task list for further results and development. T2 - International Conference on Sustainable Materials, Systems and Structures (SMSS 2019) CY - Rovinj, Croatia DA - 20.3.2019 KW - Concrete KW - Ultrasound KW - Monitoring KW - coda wave interferometry PY - 2019 SN - 978-2-35158-227-5 SP - 1 EP - 11 PB - RILEM Publications S.A.R.L. CY - Paris, France AN - OPUS4-47677 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Brandt, S. A1 - Müller, B. A1 - de Lima Vasconcelos, S. A1 - Plehn, W. A1 - Brozowski, F. A1 - Horn, Wolfgang A1 - Sattler, M. T1 - Präzisierung der Geruchsprüfung für Bauprodukte nach DIN ISO 16000-28 – Untersuchung von Vergleichsmaßstäben N2 - Bauprodukte, die in Innenräumen verwendet werden, sollten die Gesundheit und das Wohlbefinden der Personen die sich darin aufhalten nicht durch das Ausdünsten von Geruchsstoffen stören. Die DIN ISO 16000-28 „Bestimmung der Geruchsstoffemissionen aus Bauprodukten mit einer Emissionsprüfkammer“ (DIN ISO 16000-28) beschreibt umfassend die Möglichkeiten der Geruchsprüfung. In Verbindung mit der Anwendung der VDI-Richtlinie 4302 Blatt 1 „Geruchsprüfung von Innenraumluft und Emissionen aus Innenraummaterialien“ (VDI 4302 Blatt 1) ist sie zur Bewertung der empfundenen Intensität von Bauprodukten mit Vergleichsmaßstab geeignet (Umweltbundesamt 2015). In einem vom Umweltbundesamt (UBA) geförderten Forschungsprojekt der Hochschule für Technik und Wirtschaft Berlin (HTW Berlin) und der Bundesanstalt für Materialforschung und –prüfung (BAM) wurden erstmals verschiedene Vergleichsmaßstäbe miteinander verglichen. Ziel des derzeitigen Folgeprojektes ist nun, Mindestanforderungen an Vergleichsmaßstäbe zu erarbeiten, welche die Reproduzierbarkeit der Ergebnisse erhöhen und mit denen die Norm konkretisiert werden kann. Dieser Beitrag stellt die Untersuchungen und Ergebnisse des ersten Projektes und die Schlussfolgerungen für die Durchführung des zweiten Projektes dar. T2 - 12. Fachkongress der Arbeitsgemeinschaft ökologischer Forschungsinstiute (AGÖF) CY - Hallstadt (Bamberg), Germany DA - 17.10.2019 KW - Geruch KW - Emission KW - Bauprodukte KW - VOC KW - Emissionskammer PY - 2019 SN - 978-3-930576-11-1 VL - 12. Fachkongress SP - 214 EP - 223 PB - Arbeitsgemeinschaft ökologischer Forschungsinstiute (AGÖF) e. V. CY - Springe-Eldagsen AN - OPUS4-49702 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völzke, Holger T1 - Stand bei den Behälterbauartprüfungen für das Endlager Konrad N2 - Die Verfügbarkeit von Behältern für die Entsorgung nicht Wärme entwickelnder radioaktiver Abfälle im Endlager Konrad stellt ein wesentliches Element des nationalen Entsorgungskonzeptes für diese Abfallart dar. Grundlage für die Verfügbarkeit geeigneter Behälter sind typspezifische Bauartprüfungen, auf deren Grundlage eine Eignungs-feststellung in Form eines Prüfzeugnisses durch die Bundesgesellschaft für Endlagerung mbH (BGE), vormals Bundesamt für Strahlenschutz (BfS), erfolgt. Die Prüfgrundlagen sind in den durch das BfS (heute BGE) veröffent-lichten „Anforderungen an endzulagernde radioaktive Abfälle“ (Endlagerungsbedingungen) sowie der zugehörigen „Produktkontrolle radioaktiver Abfälle, radiologische Aspekte“ (PK) verankert. Die Eignungsfeststellung für eine Be-hälterbauart ist gleichzeitig die Grundlage für eine Behälterserienfertigung entsprechend den im Prüfzeugnis veran-kerten Spezifikationen und Randbedingungen. Mit den Gesetzen zur Neuordnung der Organisationsstruktur im Bereich der Endlagerung (Mitte 2016) und zur Neuordnung der Verantwortung in der kerntechnischen Entsorgung (Mitte 2017) mit der Finanzierung des Kern-energieausstiegs wurden wesentliche Weichenstellungen im Hinblick auf den anstehenden Rückbau der bereits stillgelegten und in den kommenden Jahren noch stillzulegenden deutschen Kernkraftwerke vorgenommen. Bezüg-lich der nicht Wärme entwickelnden radioaktiven Abfälle führt dies zu einer spürbaren Intensivierung der Anstren-gungen zur Bereitstellung qualifizierter Gebinde für das Endlager Konrad, das nach aktueller Planung bis 2027 sei-nen Einlagerungsbetrieb aufnehmen soll. Dies wiederum führt zu einer erheblichen Verdichtung der Verfahren zur Behälterbauartprüfung, die allen Seiten (Antragsteller, BGE, Gutachter) erhebliche Anstrengungen abfordert. Die Bundesanstalt für Materialprüfung und –forschung (BAM) ist auf Grundlage des Kap. 7 der o. g. „Produktkon-trolle …“ (PK) von der BGE mit den Behälterbauartprüfungen für das Endlager Konrad beauftragt. Hierbei ist eine Vielzahl von Anforderungen zu berücksichtigen, wozu neben den Anforderungen an Abfallbehälter gemäß Kap. 5 der Endlagerungsbedingungen weitere Anforderungen an die Verpackung (Kap. 3.2.2 PK), Kenngrößen (Kap. 3.5.1 PK) und schließlich die eigentliche Prüfung von Behältern/Verpackungen zählt (Kap. 7 PK). Letzteres beinhaltet die umfassende Behälterbeschreibung und –spezifikation, die Behälterauslegung, die thermischen und mechanischen Baumusterprüfungen (z.B. Brand- und Fallprüfungen), und schließlich die qualitätssichernden Maßnahmen für Her-stellung und Betrieb der Behälter. Neben der klassischen Bauartprüfung neuer Behältertypen spielt auch die Prü-fung bereits hergestellter Behälter, sog. Altbehälter, eine wesentliche Rolle, da sich etliche tausend Gebinde bereits in der Zwischenlagerung befinden und nach Möglichkeit für das Endlager Konrad qualifiziert werden sollen. Dieser Beitrag berichtet aktuell über den Umfang und Stand der laufenden Bauartprüfungen bei der BAM unter Be-rücksichtigung der besonderen Herausforderungen und der zuletzt erzielten Fortschritte. Dabei erfordert die paral-lele Bearbeitung der zahlreichen Verfahren einen verstärkten Koordinierungsbedarf hinsichtlich vergleichbarer fach-licher Aspekte sowie hinsichtlich Priorisierung und Ressourceneinsatz. Bei den experimentellen Nachweisen (Fall- und Brandversuche) betrifft das hinsichtlich der Nutzung der Versuchseinrichtungen bei der BAM die Koordination mit anderen Prüfaufträgen, wie z. B. verkehrsrechtliche Baumusterprüfungen. Schließlich erfordern diverse Fach-fragen zur Interpretation der Anforderungen aus Endlagerungsbedingungen und Produktkontrolle intensive Abstim-mungsprozesse zwischen BAM, BGE und Antragstellern. Wichtige Ergebnisse mit übergeordneter Bedeutung wer-den in Form erläuternder Fachnotizen durch die BGE veröffentlicht und können so bei zukünftigen Antragsverfahren berücksichtigt werden. T2 - KONTEC 2019 CY - Dresden, Germany DA - 27.03.2019 KW - Endlager KW - Container KW - Bauartprüfung KW - Konrad PY - 2019 SP - Paper 017, 205 EP - 212 PB - Kontec GmbH CY - Hamburg AN - OPUS4-47667 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Habib, Abdel Karim A1 - Kluge, Martin T1 - Experimentelle Untersuchungen zu Schäden an Membranabdeckungen im Biogasbereich N2 - Bei Störfallauswirkungsbetrachtungen an Biogasanlagen muss das Versagen der Membranabdeckung des Fermenters untersucht werden. Hierbei sind insbesondere Risse in derselben hinsichtlich des austretenden Massenstromes an Biogas zu bewerten, ebenso wie der durch eine Zündung resultierende Flammenstrahl. Zurzeit existieren für Membranabdeckungen jedoch keine Erkenntnisse zu realistischen Ausflussziffern für die Massenstromberechnung. Im Leitfaden KAS-32 wird für Störfallauswirkungsbetrachtungen für die Berechnung des austretenden Massenstromes eine Ausflussziffer von 1 und eine „Leckfläche" von 0,6 m2 vorgegeben. Die Anwendbarkeit verfügbarer Modelle zur Berechnung des Flammenstrahls ist bisher ebenso ungeklärt. Um diese Fragestellungen zu untersuchen, wurden in der BAM Versuche zur Bestimmung der Ausflussziffer, sowie der Zündung des austretenden Gases an einem 80 m3 Sack zur Speicherung von Biogas durchgeführt, der aus demselben Material besteht wie die in Biogasanlagen verwendeten Membranabdeckungen. T2 - 14. Fachtagung Anlagen-, Arbeits- und Umweltsicherheit CY - Köthen, Germany DA - 07.11.2019 KW - Biogas KW - Ausflussziffer KW - Membranabdeckung PY - 2019 SN - 978-3-89746-220-5 VL - 2019 SP - 142 EP - 152 AN - OPUS4-50857 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bayane, I. A1 - Long, Lijia A1 - Thöns, Sebastian A1 - Brühwiler, E. T1 - Quantification of the conditional value of SHM data for the fatigue safety evaluation of a road viaduct N2 - Fatigue safety verification of existing bridges that uses ‘‘re-calculation’’ based on codes, usually results in insufficient fatigue safety, triggering invasive interventions. Instead of “re-calculation”, Structural Health Monitoring (SHM) should be used for the assessment of the existing bridges. Monitoring systems provide data that can reduce uncertainties associated with the fatigue loading process and the structural resistance. The objective of this paper is to quantify the value of the SHM system implemented in a 60-years-old road viaduct to investigate its fatigue safety, through modeling of the fundamental decisions of performing monitoring in conjunction with its expected utility. The quantification of the conditional value of information is based on the decision tree analysis that considers the structural reliability, various decision scenarios as well as the cost-benefit assessments. This leads to a quantitative decision basis for the owner about how much time and money can be saved while the viaduct fulfills its function reliably and respects the safety requirements. The originality of this paper stands in the application of the value of information theory to an existing viaduct considering the fatigue failure of the system based on the monitoring data and the cost-benefit of monitoring method. T2 - 13th International Conference on Applications of Statistics and Probability in Civil Engineering CY - Seoul, South Korea DA - 26.05.2019 KW - Fatigue safety KW - Value of information PY - 2019 SP - 275 EP - 288 CY - Seoul, South Korea AN - OPUS4-50809 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Quercetti, Thomas A1 - Scheidemann, Robert A1 - Komann, Steffen A1 - Ballheimer, Viktor A1 - Wille, Frank T1 - Package testing of a dual purpose cask for SNF from German research reactors N2 - A new dual purpose cask design was developed for the safe transport and interim storage of spent fuel elements of German research reactors. In the framework of the safety assessment within the licensing procedure the Bundesanstalt für Materialforschung und –prüfung (BAM) as competent authority performed a series of drop tests according to the IAEA-Regulations [1]. The package consists of a cylindrical thick-walled ductile cast iron cask body closed by a double lid system with metallic seals. A lid and bottom sided impact limiter consisting of a wood/steel construction limit the mechanical impact loading. The full-scale test specimen was equipped with a basket and assembled with dummy-fuel elements. The package and test specimen, respectively have a total mass of approximately 24 metric tons. The mechanical test program included three 9m free drop tests, in horizontal, vertical and oblique cask orientation onto the lid system. Additionally, a 1m-puncture drop test followed the horizontal drop test to consider an IAEA-test sequence. The horizontal and vertical drop tests were performed at a temperature of minus 40°C. During the oblique drop test the upper impact limiter was heated to +80°C. The tests were conducted onto an unyielding target, fulfilling the requirements of the IAEA regulations [1]. The test specimen was considerably instrumented with strain gauges and accelerometers. Transient strains at selected locations of the inner and outer container walls, of the primary and secondary lid, as well as of the corresponding lid bolts were measured during the drop tests. Furthermore, decelerations in different locations at the cask body and the lids were measured. The complex geometrical deformation of the impact limiters due to the impact were determined by optical 3d- measurements using the projected fringe method in combination with multi-image photogrammetry. Before and after the drop tests the leakage rate of the lid system was determined by helium leakage testing. The experimental results contribute to the evaluation of the package response to mechanical tests, demonstrating safety under normal and accident conditions of transport. Especially to the verification of the dynamic finiteelement model of the package used in the package design safety report [2]. The paper describes the performance of the drop tests, selected test results focusing on the lid screws and the cask body and the deformation of the impact limiters as well as impact kinematics, respectively. T2 - IHLRWM2019 CY - Knoxville, TN, USA DA - 14.04.2019 KW - Drop test KW - Package testing KW - Dual purpose cask PY - 2019 SN - 978-0-89448-761-3 VL - 2019 SP - paper 27283, 1 EP - 7 PB - ANS AN - OPUS4-50619 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Quercetti, Thomas A1 - Scheidemann, Robert A1 - Komann, Steffen A1 - Ballheimer, Viktor A1 - Wille, Frank T1 - Drop Testing of a New Package Design for the Transport of SNF from German Research Reactors N2 - A new dual purpose cask design was developed for the safe transport and interim storage of spent fuel elements of German research reactors. In the framework of the safety assessment within the package approval procedure the Bundesanstalt für Materialforschung und –prüfung (BAM) as competent authority performed a series of drop tests according with the IAEA Transport Regulations. The package consists of a cylindrical thick-walled ductile cast iron cask body closed by a bolted lid system with metallic seals. A lid and bottom sided impact limiter consisting of a wood/steel construction limit the mechanical impact loading. The full-scale test specimen was equipped with a basket and assembled with dummy-fuel elements. The package and test specimen, respectively have a total mass of approximately 24 metric tons. The mechanical drop test program included three 9m free drop tests, in horizontal, vertical and oblique cask orientation onto the lid system. Additionally, a 1m-puncture bar drop test followed the horizontal drop test to consider an IAEA-drop test sequence. The horizontal and vertical drop tests were performed at a temperature of minus 40°C. During the oblique drop test the upper impact limiter was heated up to +80°C. The tests were conducted onto an unyielding target, fulfilling the IAEA requirements. The test specimen was considerably instrumented with strain gauges and accelerometers. Transient strains at selected locations of the inner and outer container walls, of the primary and secondary lid, as well as of the corresponding lid bolts were measured during the drop tests. Furthermore, decelerations in different locations at the cask body and the lids were measured. The complex geometrical deformation of the impact limiters due to the impact were determined by optical 3D- measurements. Before and after the drop tests the leakage rate of the lid system was determined by helium leakage testing. The experimental results contribute to the evaluation of the package response to mechanical tests, demonstrating safety under normal and accident conditions of transport and especially to the verification of the dynamic finite-element model of the package used in the package design safety report. T2 - PATRAM 2019 CY - New Orleans, LA, USA DA - 04.08.2019 KW - SNF KW - Drop testing KW - New package design PY - 2019 SP - Paper 19-A-1142,1 EP - 10 AN - OPUS4-50622 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sichler, Theresa A1 - Adam, Christian A1 - Montag, D. A1 - Ehm, J. A1 - Barjenbruch, M. A1 - Pinnekamp, J. ED - Holm, O. ED - Thomé-Kozmiensky, E. ED - Quicker, P. ED - Kopp-Assenmacher, S. T1 - Auswirkungen der novellierten AbfKlärV auf die Kreislaufführung von Pflanzennährstoffen N2 - Because of the longstanding oversupply of nutrients in Germany, waste and fertilization legislation has been amended in 2017. As the new laws do still not meet the European nitrate ordinance, fertilization laws must be tightened again. In consequence, there is a rising competition for land between sewage sludge and organic fertilizers. Furthermore, the new sewage sludge ordinance (AbfKlärV) contains stricter thresholds and a ban on agricultural sewage sludge utilization for WWTPs > 50,000 p.e. from 2029. WWTPs which do not use their sludge for agriculture have to recover phosphorus from then on. However, sludges with less than 2% P content are not affected by that obligation. Every federal state of Germany must report amounts and quality of agricultural utilized sewage sludge yearly. An evaluation of raw data from 10 federal states shows that nearly 40% of both WWTPs and sewage sludge volume fall below the recovery limit of 2%. On the other hand, this means less than 30% of the P potential. In addition, there is no information whether the sludges fall reliably below the limit as required by the ordinance. This project aims to investigate this reliability by regarding the variations in the P content of sewage sludge. For this reason, samples will be taken monthly at 10 representative WWTPs over a year. Whereas phosphorus will still mostly be subject of recovery other nutrients are not affected by this. As a result, large amounts of N, K, Mg and Ca will be increasingly removed from the cycle. In 2017, WWTPs > 50,000 p.e. accounted for 30-60% of the nutrient potentials. These potentials will probably get lost to a large extent due to the fertilization ban. Many small WWTPs are also currently changing their utilization strategy from agriculture to incineration to ensure a safe disposal in future. Therefore, we can expect that even larger amounts of nutrients apart from phosphorus will be discharged from the circular economy. In comparison to the domestic sales volume of mineral fertilizers these other nutrients do only account for a very small fraction. A recovery could nevertheless replace parts of the mineral fertilizers, thus reducing environmental impacts. Energy consumption for technical nitrogen fixation is high and nutrient cycles are strongly anthropogenic influenced with diverse consequences such as eutrophication, acidification and endangered groundwater resources. Sewage sludge contains several micronutrients next to the macronutrients P, N, K, Mg, Ca and S. Because of lacking information on the actual German need for micronutrients contents and freights cannot evaluated. Moreover, former sewage sludge fertilization was probably not needs-based. It is therefore not possible to estimate a true loss in micronutrients due to the amended sewage sludge ordinance. N2 - Die landwirtschaftliche Klärschlammverwertung ist in der Bundesrepublik Deutschland seit Jahren rückläufig, hatte im Jahr 2017 jedoch noch einen Anteil von rund 18 % [20]. Diese Art der Verwertung wird kontrovers diskutiert, da der Klärschlamm im Rahmen der Abwasserreinigung eine Schadstoffsenke darstellt. In vergangenen Jahrzehnten wurden insbesondere die hohen Gehalte an Schwermetallen im Klärschlamm als kritisch für eine landwirtschaftliche Verwertung eingestuft. Diese Belastung konnte allerdings durch Absenkung der Einträge von Schmermetallen in das Abwasser signifikant gesenkt werden. Neben Schwermetallen kamen jedoch auch organische Schadstoffe wie Pharmazeutika, Kosmetika und Haushaltschemikalien in den Fokus der Diskussion über den Einsatz von Klärschlamm auf Agrarflächen. Heute geraten zunehmend weitere Inhaltsstoffe in den Fokus, deren Auswirkungen noch nicht abschließend geklärt sind, weshalb eine einheitliche Bewertung über Grenzwerte nicht darstellbar ist. Beispiele für diese neuen Stoffgruppen sind Mikroplastik, Nanopartikel, Antibiotikaresistenzen und persistente organische Spurenstoffe. Neben den angesprochenen Risiken gibt es in Deutschland Regionen mit einem stark erhöhten Nährstoffüberschuss. In der Kritik steht vor allem eine nicht ordnungsgemäße Düngung mit Stickstoff, welche mit Nitratauswaschungen in das Grundwasser einhergeht. Um diese Grundwasserbelastung zu verhindern wurde u.a. das Düngerecht erneut verschärft, was die Flächenkonkurrenz zwischen Klärschlamm und Wirtschaftsdünger weiter vergrößern wird. Auf Druck der EU-Kommission stehen zudem weitere Anpassungen im Düngerecht bevor, da die beschlossenen Änderungen aus Kommissionssicht nicht ausreichen, um die Nitratrichtlinie einzuhalten. Vor dem Hintergrund der angeführten Probleme wurde im Koalitionsvertrag der 18. Legislaturperiode (2013) festgeschrieben, „die Klärschlammausbringung zu Düngezwecken [zu] beenden und Phosphor und andere Nährstoffe zurück[zu]gewinnen“ [5]. Die novellierte AbfKlärV beinhaltet allerdings kein grundsätzliches Aufbringungsverbot und eine Rückgewinnungspflicht besteht lediglich für den Nährstoff Phosphor. Es ist davon auszugehen, dass sich die neuen Regelungen im Düngerecht und der Klärschlammverordnung massiv auf die landwirtschaftliche Verwertung von Klärschlamm und damit auf die Kreislaufwirtschaft verschiedener Nährstoffe auswirken werden. Zur Ermittlung dieser Auswirkungen wird seit Oktober 2018 im Auftrag des Umweltbundesamtes das REFOPLAN-Projekt „extraWERT“ (FKZ 3718 26 330 0) von der Bundesanstalt für Materialforschung und -prüfung (BAM) in Kooperation mit dem Institut für Siedlungswasserwirtschaft (ISA) der RWTH Aachen durchgeführt. In diesem Beitrag werden erste Ergebnisse dieses Projekts vorgestellt. T2 - Klärschlammkonferenz CY - Berlin, Germany DA - 04.11.2019 KW - Klärschlammdüngung KW - Landwirtschaft KW - Makronährstoffe PY - 2019 SN - 978-3-944310-49-7 VL - 2 SP - 362 EP - 374 PB - Thomé-Kozmiensky Verlag CY - Neuruppin AN - OPUS4-49603 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Genath, A. A1 - Hofmann, Michael A1 - Tiebe, Carlo A1 - Einspanier, R. T1 - Auf dem Weg zum Monitoring der Ameisensäurekonzentration in der Bienenstock-Luft mit einem Multigassensorsystem N2 - Die Varroose gilt weltweit als eine der bedeutendsten Erkrankungen der westlichen Honigbiene, Apis mellifera. Verursacht wird sie durch den Ektoparasiten Varroa destructor, der durch Saugen der Hämolymphe und Virenübertragung sowohl die Bienenbrut als auch die adulten Individuen schädigt. Ohne imkerliche Unterstützung gehen betroffene Bienenvölker in der Regel innerhalb von drei Jahren ein. Als bewährte, häufige Behandlung wird flächendeckend 60%ige Ameisensäure (AS) - im Bienenstock appliziert über verschiedene Verdampfungssysteme - eingesetzt. Sie wirkt als einziger zugelassener Stoff gegen die Varroamilbe auch in die verdeckelte Brut hinein und birgt kein Risiko der Resistenzentwicklung. Allerdings ist das therapeutische Fenster, der Bereich zwischen Milbenabtötung und Bienenschädigung, relativ schmal und die tatsächliche AS-Konzentration im Bienenstock stark abhängig von äußeren Einflussfaktoren, wie Temperatur, Luftfeuchte oder Applikationsart. Eine Bestimmung der exakten AS-Konzentration im Bienenstock ist also notwendig, um einerseits das Wirkungsoptimum zu bestimmen und andererseits bei Übersteigen der Maximalkonzentrationen mit Folge-Schädigung der Bienen, ein rechtzeitiges Eingreifen der Imker zu ermöglichen. T2 - 6. HSN-Fachsymposium „Innovative Sensorik, verteilte Sensorsysteme, neue Technologien und Anwendungsfelder“ CY - Karlsruhe, Germany DA - 06.11.2019 KW - Biene KW - Apis mellifera KW - Varroa destructor KW - Ameisensäure KW - Multigassensorik PY - 2019 SP - 22 EP - 25 AN - OPUS4-49605 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niemz, P. A1 - Baensch, Franziska A1 - Brunner, A. J. A1 - Gaff, M. T1 - Acoustic Emission Analysis and Synchrotron- Based Microtomography on Glued Shear Strength Samples from Spruce Solid Wood N2 - For a better understanding of the damage of glued wood tensile tests on miniature specimens made of glued spruce wood with acoustic emission and in-situ synchrotron-based X-ray computer microtomography has been monitored. As adhesive, urea-formaldehyde resin was used. For comparison purposes, tensile tests were carried out on solid wood and bonded miniature tensile shear samples with acoustic emission. The acoustic emission signals of all experiments were with classified pattern recognition. This resulted in two classes of signals for each two frequency peaks. In one class was the low-frequency, in the other the higher frequency peak of higher intensity, but this essentially independent from the structure (solid wood or plywood) and the size scale of the test specimens. The influence of the adhesive layers was determined on plywood test specimens in laboratory scale and on miniature test specimens with an adhesive layer and selected fiber orientations examined. This gave evidence that the sound emission signals from the failure of the adhesive layer presumably of the class with low frequency signals peak in the range of services can be assigned. T2 - 21st International Nondestructive Testing and Evaluation of Wood Symposium CY - Freiburg, Germany DA - 24.09.2019 KW - Bondline KW - Insitu test KW - Acoustic emission KW - Sychrotron tomography PY - 2019 SP - 168 EP - 175 AN - OPUS4-49558 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schalau, Sebastian A1 - Habib, Abdel Karim T1 - CFD-Simulation von Schwergasausbreitungen in bebautem Gelände N2 - Um die Ausbreitung von Schwergaswolken infolge störfallbedingter Freisetzungen in bebautem Gelände besser vorhersagen zu können, wird eine praxisorientierte Methode zur numerischen Simulation von Schwergasausbreitungen vorgestellt. T2 - 14. Fachtagung Anlagen-, Arbeits- und Umweltsicherheit CY - Köthen, Germany DA - 07.11.2019 KW - Schwergasausbreitung KW - CFD KW - OpenFOAM PY - 2019 SN - 978-3-89746-220-5 SP - 130 EP - 139 AN - OPUS4-49570 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schalau, Bernd A1 - Schalau, Sebastian T1 - Die neue VDI-Richtlinie 3783 Blatt 1. Stand der Diskussion N2 - Die VDI-Richtlinien 3783 Blatt 1 und Baltt 2 gelten immer noch im Bereich der Störfallauswirkungsbetrachtungen als Stand der Technik, obwohl sie aus den Jahren 1987 und 1990 stammen. In der Kommission Reinhaltung der Luft im VDI und DIN wurde 2009 die Arbeitsgruppe „Ausbreitung von störfallbedingten Freisetzungen – Sicherheitsanalyse“ mit der Zielsetzung gegründet, die VDI-Richtlinie 3783 zu überarbeiten. Der Inhalt des jetzt vorliegenden Gründrucks wird vorgestellt. T2 - 14. Fachtagung Anlagen-, Arbeits- und Umweltsicherheit CY - Köthen, Germany DA - 07.11.2019 KW - Störfall-Verordnung KW - Auswirkungsbetrachtung PY - 2019 SN - 978-3-89746-220-5 SP - 120 EP - 129 AN - OPUS4-49573 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schaumann, P. A1 - Schürmann, K. A1 - Pittner, Andreas A1 - Rethmeier, Michael T1 - Prediction of the Initial Fatigue Crack Location of Automatically Welded Tubular Joints for Jacket Support Structures N2 - To increase the competitiveness of jacket substructures compared to monopiles a changeover from an individual towards a serial jacket production based on automated manufactured tubular joints com-bined with standardized pipes has to be achieved. Therefore, this paper addresses fatigue tests of automatical-ly welded tubular X-joints focusing on the location of the technical fatigue crack. For this X-joint, the detect-ed location of the technical crack is then compared to numerical investigations predicting the most fatigue prone notch considering the structural stress approach as well as the notch stress approach. Additionally, the fatigue prone hot spot according to both approaches is compared for a typical offshore jacket double-K-joint to emphasize the significance of the presented outcomes for the existing offshore structures. Besides, the welding process of the automated manufactured tubular X-joints is presented. T2 - 7th International Conference on Structural Engineering, Mechanics and Computation (SEMC) CY - Cape Town, SOUTH AFRICA DA - 02.09.2019 KW - Lightweight Design KW - Jacket Support Structures KW - Arc Welding Automation KW - Fatigue KW - Offshore Wind PY - 2019 SN - 978-1-138-38696-9 DO - https://doi.org/10.1201/9780429426506-100 VL - 2019 SP - 575 EP - 580 AN - OPUS4-51847 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schaumann, P. A1 - Schürmann, K. A1 - Pittner, Andreas A1 - Rethmeier, Michael T1 - Automatically Welded Tubular X-Joints - Welding Procedure and Prediction of the Technical Fatigue Crack Location N2 - To increase the competitiveness of jacket substructures compared to monopiles a changeover from an individual towards a serial jacket production based on automated manufactured tubular joints combined with standardized pipes has to be achieved. Therefore, this paper ad-dresses the welding process of automated manufactured tubular X-joints. Additionally, fatigue tests of the automatically welded tubular joints are presented focusing on the location of the technical fatigue crack. The detected location of the technical crack is compared to numerical investigations predicting the most fatigue prone notch con-sidering the structural stress approach as well as the notch stress ap-proach. T2 - 29th International Ocean and Polar Engineering Conference CY - Honolulu, Hawaii, USA DA - 16.06.2019 KW - Notch stress approach KW - Tubular X-joints KW - Automated manufacturing KW - Fatigue tests KW - Structural stress approach PY - 2019 SN - 978-1-880653-85-2 SP - 4098 EP - 4105 AN - OPUS4-51848 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wilsch, Gerd A1 - Günther, Tobias A1 - Völker, Tobias T1 - LIBS – Betonanalytik mit dem Laser N2 - Es wird ein alternatives Verfahren zur schnellen zweidimensionalen Analyse der chemischen Zusammensetzung von Baustoffen vorgestellt. Dieses beruht auf der Kombination des Abtrags einer geringen Materialmenge durch einen gepulsten Laser, der Plasmaerzeugung und der Analyse der Lichtemission des Plasmas mittels optischer Spektroskopie. Es können prinzipiell alle Elemente gleichzeitig nachgewiesen werden. Damit ist es möglich einerseits Informationen über den Baustoff an sich als auch über den Eintrag potentiell schädigender Elemente (z. B. Cl, C, Na, K, S) zu gewinnen. Das Verfahren kann automatisiert im Labor oder als mobile Version direkt vor Ort eingesetzt werden. Es liefert zweidimensionale Bilder der Elementverteilung in Echtzeit. Es kann ohne große Probenvorbereitung z. B. direkt an der Querschnittsfläche eines Bohrkernes gemessen werden. Die Messung dauert nur wenige Minuten. Das Prinzip der Messung, die Vor- und die Nachteile, sowie die verfügbare Gerätetechnik für den Einsatz im Labor oder direkt am Bauwerk werden vorgestellt. Abschließend werden praktische Beispiele für die Anwendung des LIBS-Verfahrens zur Erfassung des Chlorid-Eintrages, der Karbonatisierung und der Verteilung von Schwefel präsentiert. T2 - 9. Betonfachtagung CY - Berlin, Germany DA - 12.11.2019 KW - Chloride KW - Beton KW - LIBS KW - Schädigung PY - 2019 SP - 1 PB - InformationsZentrum Beton GmbH CY - Berlin AN - OPUS4-51675 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lugovtsova, Yevgeniya A1 - Mesnil, Olivier A1 - Bulling, Jannis A1 - Prager, Jens A1 - Boller, C. T1 - Damage Quantification in Aluminium-CFRP Composite Structures using Guided Wave Wavenumber Mapping N2 - The use of composite materials is associated not only with the advantages of weight reduction and improved structural performance but also with the risk of barely visible impacts or manufacturing damages. One of the promising techniques for the detection and characterisation of such damages is based on ultrasonic guided wave propagation and analysis. However, the multimodal nature and dispersive behaviour of these waves make their analysis difficult. Various signal processing techniques have been proposed for easier interpretation of guided wave signals and extraction of the necessary information about the damage. One of them is the wavenumber mapping which consists of creating a cartography of the wavenumber of a propagating mode over an inspected area, using a dense wavefield acquisition measured for example with a scanning laser Doppler vibrometer. This technique allows both the quantification of the in-plane size and the depth of damage, for example, impact-induced delamination in composite laminates. In this contribution, wavenumber mapping is applied to a delaminated aluminium-CFRP composite structure which corresponds to composite-overwrapped pressure vessels used for storing gases in aerospace and automotive industries. The analysis of experimental data obtained from measurements of guided waves propagating in an aluminium-CFRP composite plate with impact-induced damage is performed. The output of the imaging is a three-dimensional representation of the delamination induced by the impact. Good agreement between conventional ultrasonic testing and guided wave damage mapping can be found. T2 - 11th International Symposium on NDT in Aerospace CY - Paris Saclay, France DA - 13.11.2019 KW - Damage assessment KW - Lamb waves KW - Multilayered structures KW - Wavefield analysis KW - Impact damage PY - 2019 SP - 33 AN - OPUS4-49663 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Meng, Xiangmeng A1 - Artinov, Antoni A1 - Bachmann, Marcel A1 - Rethmeier, Michael T1 - A theoretical study of influence o f electromagnetic stirring on transport phenomena in wire feed laser beam welding N2 - The additional element from the filler wire in the laser beam welding is usually distributed inhomogeneously in the final weld due to the high solidification rate of weld pool. It has been found that the electromagnetic stirring produced by an external oscillating magnetic field can enhance the material mixing in the weld pool to achieve a more uniform element distribution. However, the magnetic field has a highly non-linear and multi-coupled interaction with the weld pool behavior, which makes the quantitative explanation of the physical mechanism difficult. In this study, the effect of electromagnetic stirring on the transport phenomena in the wire feed laser beam welding is investigated by a numerical modelling. A 3D transient multi-physical model considering the magnetohydrodynamics, heat transfer, fluid flow, keyhole dynamics and element transport is developed. The multiple reflections and the Fresnel absorption of the laser on the keyhole wall are calculated using the ray tracing method. The numerical results show that a Lorentz force produced by the oscillating magnetic field and its induced eddy current gives significant influence on the transport phenomena in the molten pool. The forward and downward flow is enhanced by the electromagnetic stirring, which homogenizes the distribution of the additional elements from a nickel-based filler wire in a steel weld pool. The numerical results show a good agreement with the high-speed images of the molten pool, the fusion line from the optical micrograph and the element distribution from the energy dispersive X-ray spectroscopy. This work provides a physical base for the electromagnetic-controlled laser beam welding and some guidance for the selection of electromagnetic parameters. T2 - ICALEO 2019 - 38th International congress on applications of lasers & electro-optics CY - Orlando, FL, USA DA - 07.10.2019 KW - Magnetohydrodynamics KW - Molten pool dynamics KW - Element transport KW - Laser beam welding PY - 2019 SN - 978-1-940168-1-42 SP - Paper # Macro 403 AN - OPUS4-49664 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ebell, Gino A1 - Burkert, Andreas T1 - Korrosionsverhalten von feuerverzinktem Betonstahl in karbonatisierten und chloridhaltigen Mörteln N2 - Der Einsatz von feuerverzinkten Betonstählen in karbonatisiewrten Betonen führt bei reduzierten Betondeckungen zu einer signifikanten Nutzungsdauerverlängerung. Bei einwirken von chloriden kann keine signifikanten Verlängerung der Nutzungsdauer durch feuerverzinkte Betonstähle erzielt werden. T2 - GfKORR Jahrestagung 2019 CY - Frankfurt a.M., Germany DA - 12.11.2019 KW - Korrosion KW - Verzinkter Betonstahl PY - 2019 SP - 65 EP - 76 AN - OPUS4-49613 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rica, S. A1 - Van Baars, S. A1 - Kullolli, Borana ED - Ülgen, D. ED - Saygili, A. ED - Kahyaoglu, M. R. ED - Durmaz, S. ED - Toygar, O. ED - Göcügenci, A. T1 - The importance of the horizontal stresses on the bearing capacity of a foundation pile N2 - In case one wants to predict or design the bearing capacity of a foundation pile and there are no possibilities to perform an in-situ test, such as a Cone Penetration Test, the pile bearing capacity is in most cases estimated with analytical formulas. The most known and used method is the Meyerhof method published some decades ago. There are also other design methods such as derived from a certain failure mechanism around the pile tip, which is, in most cases, wedge failure mechanism. This failure mechanism was originally developed for a shallow (infinite) strip foundation, though. Therefore, it represents a plane failure mechanism. Numerical simulations on loaded foundation piles performed with the Plaxis software Show however, that the failure mechanism of a foundation pile represents a far more complex threedimensional failure mechanism around the pile tip. In addition, the existing analytical methods for foundation piles are based on the vertical stresses in the soil, as if the failure mechanism is the same as of a shallow foundation. Numerical simulations, performed in Plaxis show that, not the vertical, but the horizontal stresses, play an important role on the pile bearing capacity. Plaxis represents the stresses in the soil by using the procedure. So, different horizontal soil stresses are obtained for different values of the lateral earth pressure coefficient. The results show that the pile tip bearing capacity depends strongly on the horizontal stresses in the soil, but only for. The same results were observed by using a Material Point Method (MPM). Consequently, the analytical methods should estimate the pile bearing. T2 - 1st Mediterranean Young Geotechnical Engineers Conference CY - Bodrum, Turkey DA - 23.09.2019 KW - Analytical Design Methods KW - Foundation Pile KW - Horizontal stress PY - 2019 UR - http://mygec2019.org/ VL - 2019 SP - 151 EP - 158 PB - 1st Mediterranean Young Geotechnical Engineers Conference CY - Bodrum, Turkey AN - OPUS4-49639 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin A1 - Burkert, Andreas A1 - Heise, Svenja A1 - Heyn, A. T1 - Korrosionsuntersuchungen mit gelartigen Elektrolyten an Zink - Eine innovative Prüfmethodik N2 - Ein neuer Ansatz bei elektrochemischen Korrosionsuntersuchungen kann durch den Einsatz von gelartigen Elektrolyten als Alternative zu wässrigen Prüfelektrolyten beschritten werden. Gelartige Elektrolyte ermöglichen minimalinvasive Untersuchungen an natürlich gebildeten Zinkdeckschichten. Dadurch können korrosionsrelevante Kennwerte ermittelt werden, die Aussagen zur Deckschichtbildung und zur Stabilität von atmosphärisch gebildeten Deckschichten erlauben. In diesem Beitrag wird anhand verschiedener Untersuchungen an Reinzink der Mehrwert von gelartigen Elektrolyten für die Korrosionsforschung und -prüfung verdeutlicht. Darüber hinaus werden neue Erkenntnisse zur Deckschichtbildung von Zink unter atmosphärischen Bedingungen vorgestellt. T2 - GfKORR-Jahrestagung 2019 CY - Frankfurt a. M. DA - 12.11.2019 KW - Zink KW - Gelartige Elektrolyte KW - Korrosionsuntersuchungen KW - Deckschichtbildung PY - 2019 SN - 978-3-935406-71-0 SP - 53 EP - 64 AN - OPUS4-49642 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heckel, Thomas A1 - Boehm, Rainer A1 - Mook, G. T1 - Ultrasonic rail inspection with array probes N2 - For more than 60 years ultrasonic rail inspection is used as non-destructive testing method to ensure the safe operation of rail tracks. Constantly increasing traffic density and heavy loads have been the motor for the development of new test equipment from handheld devices to rail inspection trains. (Krull 2003)Up to the present most of the system solutions feature conventional ultrasonic transducers housed in wheel-type and slide-type probes. Different tasks have to be carried out during an in-service inspection for flaws in the rail head, rail web and rail foot as well as rolling contact fatigue (Heckel 2018). The more tasks the inspection system has to perform, the more probes are needed. Compared against standard ultrasonic testing methods the application of array probes offers advantages and flexibility by the electronic steering possibilities to control the transmitted and received sound fields. This allows to increase functionality by software while decreasing the number of probes needed in hardware in parallel. One drawback in application of phased array probes is that the repetition frequency of the subsequent measurements will be reduced by the number of virtual probe functions each phased array probe has to perform. This may limit the range of use for phased array probes in high speed applications. To overcome these limits special designs for array probes and signal processing are necessary. T2 - Railway Engineering 2019 CY - Edinburgh, UK DA - 03.07.2019 KW - High speed KW - Ultrasound KW - Rail inspection KW - Phased array probes PY - 2019 VL - 2019 SP - 1 EP - 3 AN - OPUS4-49680 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Winkler, Nicolas P. A1 - Lilienthal, A. J. A1 - Neumann, Patrick P. ED - Zemčík, R. ED - Krystek, J. T1 - Boosting a Low-Cost Sensor Network with Mobile High-Quality Sensors N2 - Occupational health is an important topic, especially in industry, where workers are exposed to airborne by-products (e.g., dust particles and gases). Therefore, continuous monitoring of the air quality in industrial environments is crucial to meet safety standards. For practical and economic reasons, high-quality, costly measurements are currently only carried out sparsely, both in time and space, i.e., measurement data are collected in single day campaigns at selected locations only. Recent developments in sensor technology enable cost-efficient gas monitoring in real-time for long-term intervals. This knowledge of contaminant distribution inside the industrial environment would provide means for better and more economic control of air impurities, e.g., the possibility to regulate the workspace’s ventilation exhaust locations, can reduce the concentration of airborne contaminants by 50%. This paper describes a concept proposed in the project “Robot-assisted Environmental Monitoring for Air Quality Assessment in Industrial Scenarios“ (RASEM). RASEM aims to bring together the benefits of both – low- and high-cost – measuring technologies: A stationary network of low-cost sensors shall be augmented by mobile units carrying high-quality sensors. Additionally, RASEM will develop procedures and algorithms to map the distribution of gases and particles in industrial environments. T2 - 36th Danubia-Adria Symposium on Advances in Experimental Mechanics CY - Pilsen, Czech Republic DA - 24.09.2019 KW - RASEM KW - Sensor network KW - Low-cost KW - Occupational health KW - Mobile Robot Olfaction PY - 2019 SP - 61 EP - 62 CY - Plzeň AN - OPUS4-49630 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kromm, Arne A1 - Kannengießer, Thomas T1 - Online-Observation of Martensite Formation by combined use of Synchrotron Diffraction and Dilatometry N2 - Welding residual stress engineering by means of an adjusted martensite phase transformation would be highly attractive as detrimental tensile residual stresses may be prevented already during welding without time and cost intensive post processing. The present study shows a synchrotron diffraction analysis of a martensitic steel subjected to thermo-mechanical load cycles. Experiments were conducted regarding the microstructural strain response during the austenite to martensite transformation. The strains are a function of the temperature and the specific loads applied during cooling. The relation between the transformation plasticity of the material, the amount of martensite formed and the arising strains can thus be assessed. The lattice plane specific strains were compared to experimental findings from (macro) dilatation tests. It is shown that the microscopic material behavior differs remarkably from the one observed on the macroscopic scale, what leads to characteristic residual stresses in the material. T2 - Visual-JW 2019 & WSE 2019 The 5th International Symposium on Visualization in Joining & Welding Science through Advanced Measurements and Simulation & The 8th International Conference of Welding Science and Engineering CY - Osaka, Japan DA - 21.11.2019 KW - Martensite KW - Synchrotron KW - Dilatometry KW - Residual stress KW - Phase transformation PY - 2019 SP - 83 EP - 84 PB - SEIEI Printing Co., Ltd CY - Osaka, Japan AN - OPUS4-49770 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kannengießer, Thomas A1 - Kromm, Arne A1 - Lausch, Thomas A1 - Schroepfer, Dirk A1 - Hannemann, Andreas T1 - In-situ Observation of Stress Evolution and Cracking during High Strength Steel Welding N2 - Residual stresses are crucial when assessing the performance of welded components. The present work deals with the possibilities of transferring the real-life boundary conditions of welding, which influence the residual stress, into the laboratory. The possibilities of a test system with a load capacity of 2 MN specifically developed for online monitoring of stress formation and cracking are shown. Due to the structural design, global process, geometry and material-dependent stresses are induced, which can be quantified in-situ during welding and post weld heat treatment. Examples are presented how the conditions to be found during production are simulated in the laboratory. It is shown how welding residual stresses in high-strength steels are affected by the heat control. Elevated working temperatures significantly increase the tensile residual stresses in the heat affected zone (HAZ). The effect of mechanical stresses resulting from welding on stress relief cracking is demonstrated by the example of a creep resistant steel. Reheat cracks were monitored online during post weld heat treatment. T2 - Visual-JW 2019 & WSE 2019 The 5th International Symposium on Visualization in Joining & Welding Science through Advanced Measurements and Simulation & The 8th International Conference of Welding Science and Engineering CY - Osaka, Japan DA - 21.11.2019 KW - Residual stress KW - Restraint KW - Welding KW - Large-scale test KW - Reheat cracking PY - 2019 SP - 83 EP - 84 PB - SEIEI Printing Co., Ltd CY - Osaka, Japan AN - OPUS4-49773 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bertovic, Marija T1 - Human-Related Risks in the Non-Destructive Testing (NDT) of Hollow Railway Axles: Implications for the Education and Training of the NDT Personnel N2 - Non-destructive testing (NDT) is a major contributor to the safe railway operation. Even though NDT reliability in railway maintenance is affected by human factors, there are only just a few studies published in this field so far. Education and training of the NDT personnel are some of the most important drivers of safe and reliable NDT. Continuously improving current practices and tools used for educational purposes can be achieved not only through technical con¬tent, but also through the attention to human factors. The aim of this study was to deepen the understanding of possible human-related risks in the manual ultrasonic inspection of the hollow railway axles and to suggest measures to improve the education and training of the NDT person¬nel. This was achieved by means of Failure Modes and Effects Analysis (FMEA) carried out with eight NDT experts and by a survey of 27 experienced inspectors. The results show that failures can happen throughout the entire NDT process. Prevention of those failures could be improved through the optimization of the organization, technology, documentation and regulations, working conditions and the general process, and through the optimization of the formal education and training. Specialized training of the executives, extended training of the supervisors and the inspectors and improvement of the inspection documentation have been suggested. The study also showed potential for the improvements of the inspection in the field. T2 - 29th European Safety and Reliability Conference CY - Hannover, Germany DA - 22.09.2019 KW - Human Factors KW - Non-Destructive Testing KW - NDT KW - Education KW - Training KW - Failure Modes and Effects Analysis KW - Railway KW - Axle Inspection KW - Ultrasonic Testing KW - Reliability PY - 2019 SN - 978-981-11-2724-3 DO - https://doi.org/10.3850/978-981-11-2724-3_1058-cd SP - 294 EP - 300 PB - Research Publishing CY - Singapore AN - OPUS4-49733 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pirskawetz, Stephan A1 - Hüsken, Götz A1 - Gründer, Klaus-Peter A1 - Kadoke, Daniel ED - Caspeele, R. ED - Taerwe, L. ED - Frangopol, D. M. T1 - Damage mechanisms analysis of reinforced concrete beams in bending using non-destructive testing N2 - Beams that are loaded in transverse direction are one of the main structural elements used in reinforced concrete structures. Bending beams are used, for example, in bridge girders or joists. The strength related failure modes at maximum loading can be divided into bending and shear failure that could occur with or without indication. Conventional design concepts used in practice for designing structural elements subjected to bending aim at failure modes with sufficient indication (e.g. large deflections or cracks), as it occurs in the case of secondary flexure-compression-failure. These indicators can also be used to identify structural changes of civil infrastructure systems (e.g. bridges) using non-destructive testing methods for Structural Health Monitoring (SHM). However, profound knowledge on the determining failure modes of bending beams is required for the reliable application of structural health monitoring. Therefore, resulting effects of different thermal and mechanical loads on the response of a structure are investigated by means of a bridge demonstrator. The results of this investigation are used for developing a monitoring system. Different non-destructive testing (NDT) methods have been used for analyzing the deformation behavior of a reinforced concrete beam in bending. The suitability of the different measuring techniques will be discussed by means of the obtained experimental results. For this purpose, the deformation behavior of a reinforced concrete beam having a span of 2.75 m was investigated in a four-point bending flexural test at laboratory scale. The focus is on the characterization of determining failure modes by the NDT methods and the comparison with classical measuring techniques (e.g. deformation measurements by displacement transducers). The bending tests have been accompanied by Acoustic Emission analysis (AE), optical deformation measurements using Stereophotogrammetry (SP) and Digital Image Correlation (DIC). The conducted tests have shown that the three-dimensional detection of deformations and resulting strains with optical techniques is beneficial for analyzing the damage mechanism of loaded structures and related crack formation and propagation. Optical techniques can be supplemented by acoustic emission testing which gives detailed information on crack formation and progressing damage. The combination of both techniques offers the application as efficient monitoring system for larger structures. T2 - Sixth International Symposium on Life-Cycle Civil Engineering (IALCCE 2018) CY - Ghent, Belgium DA - 28.10.2018 KW - Concrete Beam KW - Bending KW - Digital Image Correlation KW - Stereophotogrammetry KW - Acoustic Emission Analysis KW - Non-Destructive Testing PY - 2019 SN - 978-1-138-62633-1 SN - 978-1-315-22891-4 SP - 2411 EP - 2417 PB - CRC Press AN - OPUS4-46439 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Carabba, L. A1 - Masi, G. A1 - Pirskawetz, Stephan A1 - Krüger, Simone A1 - Gluth, Gregor A1 - Bignozzi, M.C. ED - Serdar, M. ED - Stirmer, N. ED - Provis, J. T1 - Thermal properties and steel corrosion in light-weight alkali-activated mortars N2 - This study aims at investigating the use of coal fly ash-based alkali activated mortars as passive fire protection system for steel structures. These systems are used to slow down the temperature rise of the steel substrate in case of fire. In addition, the protective system should guarantee the ability to prevent and/or mitigate steel corrosion phenomena. The behavior of a light-weight mortar was compared to that of a normal-weight mortar. Density and porosity were measured to better characterize the physical properties of the mortars. The degree of protection in case of fire was assessed by performing medium-scale fire tests. Acoustic emission measurements were conducted to analyze cracking phenomena during the high temperature exposure. The corrosion process was evaluated using an electrochemical approach in order to monitor the durability of the developed material. Preliminary results show that a 20 mm-thick layer of light-weight mortar is able to protect the steel substrate from reaching the critical temperature of 500 °C for 38 minutes in case of cellulosic fire. In addition, alkali activated mortars provide protection for carbon steel in presence of aggressive environment (i.e. presence of chlorides). The corrosion resistance is strictly related to the physical properties of the developed mortars. T2 - International Conference on Sustainable Materials, Systems and Structures (SMSS 2019) CY - Rovinj, Croatia DA - 20.03.2019 KW - Fire resistance KW - Steel corrosion KW - Acoustic emission KW - Alkali-activated materials PY - 2019 SN - 978-2-35158-223-7 VL - 1 SP - 125 EP - 132 PB - RILEM Publications CY - Paris AN - OPUS4-47584 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hlavacek, Petr A1 - Reinemann, Steffi A1 - Gluth, Gregor A1 - Ebell, Gino A1 - Mietz, Jürgen ED - Serdar, M. ED - Stirmer, N. ED - Provis, J. T1 - Behaviour of reinforced alkali-activated fly ash mortars under leaching conditions N2 - Corrosion of steel reinforcement in concrete is one of the major deterioration mechanisms limiting the service life of reinforced concrete structures. While for conventional (Portland cement-based) concretes a great amount of experience exists in this regard, the factors that determine the onset of reinforcement corrosion in alkali-activated materials are incompletely understood yet. One aspect of corrosion protection is leaching and the accompanying changes of the concrete pore solution. In the present study, alkali-activated fly ash mortars with embedded carbon steel rebars were exposed to de-ionised water for periods up to 330 days, and the electrochemical response of the steel (free corrosion potential, polarisation resistance), the alteration of the mortar (ohmic resistance, mechanical strength, pore size distribution) as well as the pore solution composition were monitored. Although substantial alkali leaching was observed, the pH of the pore solution remained at values sufficient to protect the embedded steel from depassivation. The mortar did not exhibit indications of significant deterioration. Thus, the present results suggest that leaching is not critical for protection of steel reinforcement in alkali-activated fly ash mortars and concretes. T2 - International Conference on Sustainable Materials, Systems and Structures (SMSS 2019) CY - Rovinj, Croatia DA - 20.03.2019 KW - Alkali-activated materials KW - Steel corrosion KW - Leaching PY - 2019 SN - 978-2-35158-223-7 VL - 1 SP - 118 EP - 124 PB - RILEM Publications CY - Paris AN - OPUS4-47585 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Priebe, Nsesheye Susan A1 - Gluth, Gregor A1 - Vogler, Nico A1 - Simon, Sebastian A1 - Kühne, Hans-Carsten ED - Serdar, M. ED - Stirmer, N. ED - Provis, J. T1 - Investigation of calcined brick clays from Central Germany for use as a sustainable pozzolan N2 - The production of Portland cement causes a substantial environmental impact, since the calcination of limestone results in high emissions of carbon dioxide. The use of supplementary cementitious materials such as calcined clays as partial replacement for Portland cement offers a solution to limit this environmental impact. This paper investigates four clays from deposits in central Germany with the aim of obtaining pozzolans for the production of Portland-pozzolana cement. The results obtained show that the calcined clays possess pozzolanic properties, which differ depending on calcination temperature and the relative amounts of Kaolinite and 2:1 clay minerals. T2 - International Conference on Sustainable Materials, Systems and Structures (SMSS 2019) CY - Rovinj, Croatia DA - 20.03.2019 KW - Supplementary cementitious materials KW - Calcined clays KW - Blended cements KW - Brick clays KW - Illitic clays PY - 2019 SN - 978-2-35158-223-7 N1 - Geburtsname von Priebe, Nsesheye Susan: Msinjili, N. S. - Birth name of Priebe, Nsesheye Susan: Msinjili, N. S. VL - 1 SP - 462 EP - 469 PB - RILEM Publications CY - Paris AN - OPUS4-47586 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlick-Hasper, Eva A1 - Goedecke, Thomas A1 - Ackermann, M. A1 - Senkel, U. T1 - Staubdichtheit von Säcken und FIBC für feste Gefahrgüter - Eine kritische Betrachtung der derzeitigen Regelsetzung und Transportpraxis N2 - In den internationalen Gefahrgutvorschriften ist vorgeschrieben, dass Säcke und flexible Großpackmittel (Flexible Intermediate Bulk Container – FIBC) staubdicht sein müssen. Eine quantitative Definition des Terminus Staubdichtheit, wie in anderen Technikgebieten üblich, ist jedoch nicht gegeben. Auch geeignete Prüfverfahren zum Nachweis der Staubdichtheit sind in den Vorschriften nicht genannt. In der Praxis der stichpunkartigen Kontrollen von Gefahrguttransporten durch die Schwerlastgruppe der Autobahnpolizei Münster werden immer wieder Austritte von pulverförmigen oder körnigen Gefahrgütern aus eigentlich intakten Säcken und FIBC detektiert. Es wird ein Überblick über die im Jahr 2018 festgestellten Gefahrgutaustritte aus diesen Gefahrgutverpackungen sowie eine systematische Einordnung hinsichtlich betroffener Bauarten und möglicher Ursachen gegeben. Bei der Stofffreisetzung aus intakten Gefahrgutverpackungen liegt ein mechanischer Transport von Partikeln durch Leckkanäle, z. B. im Verschluss-, Naht- oder Wandungsbereich, vor. Generell kommen zwei Freisetzungswege in Frage: Einerseits eine Langzeit-Freisetzung während des Transports, hervorgerufen durch eine kombinierte Wirkung von Stapellast des Füllguts und Transportvibrationen; andererseits eine stoßartige Freisetzung. Auf Grundlage von durchgeführten Untersuchungen hinsichtlich der stoßartigen Freisetzung pulverförmiger Stoffe aus Gefahrgutsäcken werden erste Lösungsansätze hin zu einer Verbesserung der Staubdichtheit von Gefahrgutsäcken und -FIBC vorgestellt. Es wird ein Ausblick auf nachfolgende Arbeiten gegeben. T2 - 48. Jahrestagung der GUS 2019 CY - Stutensee, Ortsteil Blankenloch, Germany DA - 27.03.2019 KW - Gefahrgutverpackungen KW - Staubdichtheit KW - Säcke KW - FIBC PY - 2019 SN - 978-3-9818507-3-4 SP - 157 EP - 170 AN - OPUS4-47691 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, T. A1 - Murtuz, A. K. M. G. A1 - Hafiz, A. A1 - Dusicka, P. A1 - Niederleithinger, Ernst ED - Gabrijel, I. ED - Grosse, C. ED - Skazlić, M. T1 - Post-earthquake damage evaluation of concrete structures using ultrasonic monitoring: A proof-of concept laboratory study N2 - In earthquake-prone regions such as the Pacific Northwest, damage assessment tools are needed to enable safety evaluations to support recovery. Currently, damage assessment is performed primarily by visual inspection and is often impossible for structural members that are inaccessible, such as deep foundations or interior members hidden by cladding. This study explores the possibility of using embedded ultrasonic transducers to monitor reinforced concrete members for damage progression under earthquake loading. A novel methodology is proposed where changes in the member condition due to an increase in the earthquake-type loading of a full-scale column-foundation specimen are correlated with changes in the recorded ultrasonic waveforms. The discussed preliminary analysis of the ultrasonic signals is based on wave propagation velocity, changes in the coda wave portion, and maximum amplitude of the signals. Three embedded transducers were used to continuously monitor the laboratory specimen during destructive testing. This paper provides an overview of the proposed methodology, outlines the laboratory experiment, and discusses some preliminary observations. T2 - International Conference on Sustainable Materials, Systems and Structures (SMSS 2019) CY - Rovinj, Croatia DA - 20.3.2019 KW - Concrete KW - Monitoring KW - Ultrasound KW - earthquake PY - 2019 SN - 978-2-35158-227-5 DO - https://doi.org/10.1007/978-3-031-07258-1_84 SP - 112 EP - 119 PB - RILEM Publications S.A.R.L. CY - Paris, France AN - OPUS4-47679 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Artinov, Antoni A1 - Bachmann, Marcel A1 - Rethmeier, Michael T1 - Äquivalente Wärmequellenmodellierung beim Hochleistungslaserstrahlschweißen dicker Bleche N2 - Der vorgestellte Modellierungsprozess dient zur Abschätzung einer geeigneten äquivalenten Wärmequelle und Berechnung des thermischen Verhaltens beim Laserstrahlschweißen. Die Methode Kombiniert die Vorteile von gägngigen Simulationsverfahren und reduziert die berücksichtigte Anzahl an physikalischen Aspekten und Kalibrierungsparameter. Durch die modellierten physikalischen Phänomene konnten die Informationen über die Strömung im Schmelzbad und dessen Einfluss auf die resultierende lokale Temperaturverteilung und folglich auf das transiente Temperaturfeld gewonnen werden. Dadurch wurde die Simulatioszeit(inkl. Kalibrierungsaufwand) auf weniger als einen Tag Rechenzeit verringert. T2 - 38. Assistentenseminar Füge- und Schweißtechnik CY - Rabenau, Germany DA - 06.10.2017 KW - Äquivalente Wärmequelle KW - Bewegtes Gitter KW - Hochleistungslaserstrahlschweißen KW - Prozesssimulation KW - Knotenweise Zwangsbedingungen PY - 2019 SN - 978-3-96144-028-3 VL - 342 SP - 66 EP - 76 PB - DVS Media GmbH CY - Düsseldorf AN - OPUS4-47699 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bente, Klaas A1 - Oeff, Julius A1 - Gaal, Mate T1 - Quantitative, zeiteffiziente, winkel- und frequenzaufgelöste Analyse von Elektretwandlern im Hör- und Ultraschallbereich N2 - Die Bildgebung oder Analyse von Materialien mittels luftgekoppelten Ultraschalls profitiert von einer hohen Geschwindigkeit, Flexibilität und Materialschonung des assoziierten Verfahrens. Die Luftankopplung hat jedoch den wesentlichen Nachteil, dass die auftretenden Impedanzsprünge an Grenzflächen zu enormen Verlusten in den Signalamplituden führen. Ultraschallwandler, die laut genug senden und sensitiv genug empfangen, um die geringen Signalamplituden noch auswerten zu können, sind somit zentraler Gegenstand der aktuellen Forschung und Entwicklung. Vielversprechende Wandlertypen sind piezokeramische Wandler, Elektretwandler, aber auch passive, breitbandige Ultraschallempfänger, wie optische Mikrophone. Die quantitative Charakterisierung der Sensitivitäten solcher Wandler wird oft vernachlässigt, da kein simples, universelles Verfahren zur Verfügung steht. In diesem Beitrag geht es um die Methodik der Charakterisierung von Luftultraschallwandlern mittels thermoakustischer Ultraschallsender. Thermoakustische Wandler erzeugen Ultraschall durch das schnelle heizen eines finiten Volumens an Luft vor dem Wandler. Die erhöhte interne Energie führt zu einer Druckänderung, welche sich als akustische Welle fortpflanzen kann. Da keine mechanische Volumenarbeit vom Wandler erbracht wird, funktioniert das Verfahren resonanzfrei. Die Charakterisierung wird am Beispiel von Elektretwandlern durchgeführt. Elektretwandler sind sensitive und immer verschleißresistentere Schallwandler, wodurch sie verbreitet Einsatz im Hör- und Ultraschallbereich finden. Geladene, zelluläre Polypropylen-Folien eignen sich besonders gut als Wandlermaterial aufgrund ihrer, verglichen mit Piezokompositen, hundertfach niedrigeren akustischen Impedanz bei gleichem piezoelektrischem Koeffizienten. Doch das winkel- und frequenzabhängige Verhalten der Wandler ist kaum untersucht und wenig quantifiziert. Es wird gezeigt, dass diese Folien eine schichtdickenabhängige Sensitivität in Größenordnungen zwischen 0.1 mV/Pa und 10 mV/Pa aufwiesen. Ein Maximum in der Sensitivität fand sich nahe ihrer mechanischen Resonanzfrequenz im Ultraschallbereich, aber auch im niederfrequenten Hörschallbereich. Darüber hinaus konnte die Winkelabhängigkeit der Sensitivität charakterisiert werden. Die Analyse konnte dabei zeiteffizient gestaltet werden, da pro Winkel eine Messung für die Berechnung der Übertragungsfunktion des Wandlers genügte. Quantifiziert wurden die Ergebnisse durch das einmalige Vermessen des Emitters mittels Laser-Doppler-Vibrometrie (LDV). Mit den erzielten Ergebnissen wurde zum einen das komplexe Sensitivitätsverhalten der Wandler untersucht, aber auch eine grundlegende Methodik aufgezeigt, wie Wandler quantitativ, multivariat charakterisiert werden können. Winkel- und frequenzaufgelöste Sensitivitäten erlauben zum einen die Analyse der Anwendbarkeit der Wandler für sämtliche Einsatzgebiete, zum anderen stehen so Rückschlüsse über die mechanische Dynamik von Elektretfolien in Aussicht, da deren Sensitivität direkt mit ihrem Elastizitätsmodul skaliert. T2 - DAGA 2019 CY - Rostock, Germany DA - 18.03.2019 KW - Luftultraschall KW - Ultraschall KW - Elektretwandler KW - Thermoakustik KW - Wandlercharakterisierung PY - 2019 SP - 748 AN - OPUS4-47712 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fischer, Daniel A1 - Beck, Uwe T1 - Visualisierung von mikro- und nanoskalierten Oberflächenstrukturen mittels abbildender Ellipsometrie N2 - In den letzten Jahren hat die Einbindung der abbildenden Ellipsometrie in die Gruppe der optischen Verfahren zur Oberflächencharakterisierung ein enormes Potential bei der Analyse von topologischen Strukturänderungen gezeigt. Der dabei abgebildete Kon-trast wurde typischerweise auf Änderungen im Brechungsindex, Absorptionseffekte oder Schichtdickenänderungen zurückgeführt. In späteren Studien wurde festgestellt, dass auch andere Faktoren, wie etwa die Krümmung der Oberfläche oder Kanten von Struktu-ren einen signifikanten Einfluss auf die Messung der ellipsometrischen Paramater haben. Um diese Effekte aus der ellipsometrischen Messung extrahieren zu können, wird auf die Analyse der Müller-Matrix zurückgegriffen. In dem hier vorliegenden Beitrag wird gezeigt, wie die Müller-Matrix-Imaging Ellipsomet-rie (MM-IE) zur Charakterisierung von Oberflächenstrukturen verwendet werden kann. Dazu werden mikro- und nanoskaliert gekrümmte Oberflächen zunächst mit verschiede-nen Referenzmethoden, wie Rasterelektronenmikroskopie (SEM), Lichtmikroskopie (OM), Weißlichtinterferenzmikroskopie (WLIM) und Rasterkraftmikroskopie (AFM) vali-diert erfasst. Der anschließende Vergleich mit den Ergebnissen der Müller-Matrix-Ima-ging-Ellipsometrie ermöglicht eine Korrelation der zugrunde liegenden Strukturphäno-mene mit den ellipsometrischen Daten. In diesem Artikel wird das Prinzip an drei industriell relevanten Strukturgruppen demonstriert: Sub-Mikropartikel, Mikropartikel und sub-mikroskalierte Vertiefungen. T2 - 14. ThGOT Thementage Grenz- und Oberflächentechnik und 6. Kolloquium Dünne Schichten in der Optik CY - Zeulenroda, Germany DA - 12.03.2019 KW - Ellipsometrie KW - Nanoskaliert KW - Mikroskaliert KW - Oberflächengeometrie KW - Brechungsindex KW - Müller-Matrix-Ellipsometrie PY - 2019 SN - 978-3-00-062102-4 SP - 1 EP - 5 AN - OPUS4-47646 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lange, Thorid A1 - Hidde, Gundula A1 - Beck, Uwe A1 - Naumann, F. A1 - Kärkkänen, I. A1 - Gargouri, H. T1 - Nanoskalige Haftvermittler zur Erhöhung der Haft- bzw. Klebfestigkeit unter Verwendung von ALD-Hybridprozessen N2 - Ziel des Projektes HARFE (Haftfestigkeit Reproduzierbarkeit Festigkeit) war es, eine Er-höhung der Haft- bzw. Klebfestigkeit auf Niedrigenergie-Polymeren (PE, PP, PTFE) zu erreichen. SENTECH realisierte dazu plasmachemische Oberflächenaktivierungen mit O2 und die Abscheidung von Aluminiumoxidschichten (Al2O3) mittels Atomic Layer Deposition (ALD), wobei die Ellipsometrie zum in-situ Monitoring der ALD-Prozesse diente. Die BAM charakterisierte die modifizierten Oberflächen bezüglich der Oberflächenenergie (OFE) und bestimmte die Verbund- bzw. Klebfestigkeit mittels der Zentrifugentechnologie T2 - 14. ThGOT Thementage Grenz- und Oberflächentechnik und 6. Kolloquium Dünne Schichten in der Optik CY - Zeulenroda, Germany DA - 12.03.2019 KW - Haftvermittler KW - ALD-Hybridprozesse KW - Klebfestigkeit KW - Atomic Layer Deposition KW - Al2O3-Schichten KW - Oberflächenenergie PY - 2019 SN - 978-3-00-062102-4 SP - 1 EP - 2 CY - Zeulenroda, Germany AN - OPUS4-47656 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schröpfer, Dirk A1 - Schaupp, Thomas A1 - Kannengießer, Thomas T1 - Kaltrissvermeidung in Schweißverbindungen aus hochfesten Feinkornbaustählen bei engen Nahtspalten und fokussiertem Lichtbogen N2 - Heute werden in Stahlkonstruktionen zunehmend hochfeste Baustähle (Streckgrenze ≥ 960 MPa) eingesetzt. Daher sind auch in Schweißnähten solche hohen Festigkeiten gefordert. Jedoch können hohe Eigenspannungen aufgrund geringerer plastischer Dehnungsreserven in diesen Schweißnähten die Sicherheit der Bauteile vermindern. Diese sind insbesondere im Zusammenhang mit Wasserstoff und Härtegefügen risskritisch. Niedrige Bauteilbeanspruchungen und Kosteneinsparungen lassen sich heutzutage mit modernen fokussierten Lichtbogenvarianten und engeren Nahtspalten erreichen. Die vorliegende Studie zeigt allerdings, dass diese modernen Schweißprozesse und die angepasste Nahtgeometrie höhere Wasserstoffkonzentrationen und signifikant gesteigerte oberflächennahe Zugeigenspannungsniveaus bedingen. Anhand mehrlagiger Schweißversuche an S960QL unter Variation von Wärmeführung, Lichtbogenvariante und Nahtöffnungswinkel wurden die Effekte und Wechselwirkungen unter Zuhilfenahme von Eigenspannungsanalytik mittels Röntgendiffraktometrie und Wasserstoffanalytik mittels Trägergasheißextraktion systematisch untersucht. Das Schweißgefüge führte unter kritischer mechanischer Beanspruchung und erhöhtem Gehalt an diffusiblem Wasserstoff insbesondere bei geringem Nahtöffnungswinkel und fokussiertem Lichtbogen zu einer deutlichen Ausbildung von Mikrorissen. Die Mikrorisse führten teils zu einer makroskopischen Ausprägung. Durch Analysen zur Nachwärmung aus der Schweißwärme heraus konnten suffiziente Wärmeführungsparameter für eine effektive Prävention solcher Risse erarbeitet werden. Die vorliegende Arbeit zeigt anhand des Interaktionssystems bei der wasserstoffunterstützten Kaltrissbildung Gefüge-Beanspruchung-Wasserstoff, welche Wärmeführungs- und Schweißparameter sich für die hochfesten Feinkornbaustähle zur Kaltrissvermeidung eignen. T2 - 3. Niedersächsisches Symposium Materialtechnik CY - Clausthal-Zellerfeld, Germany DA - 14.02.2019 KW - Hochfeste Feinkornbaustähle KW - Kaltrisse KW - MAG-Schweißen KW - Eigenspannungen KW - Wasserstoff KW - Wärmeführung PY - 2019 SN - 978-3-8440-6471-1 SN - 2364-0804 VL - 7 SP - 377 EP - 389 PB - Shaker Verlag CY - Aachen AN - OPUS4-47497 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sturm, Patrick A1 - Gluth, Gregor A1 - Brouwers, H.J.H. A1 - Kühne, Hans-Carsten ED - Barcevic, A. ED - Rukavina, M.J. ED - Damjanovic, D. ED - Guadagnini, M. T1 - Shrinkage and bond behaviour of one-part alkali-activated mortars N2 - Mortars for application on concrete, e.g. repair mortars or protective coatings, need to have a durable bond to the substrate. This bond is determined by the adhesion between the two materials and by the differential deformations of the mortar and the substrate. In the present contribution, the hygric deformations (shrinkage/expansion) of novel one-part alkali-activated mortars and their bond to concrete substrates are studied. Shrinkage of the mortars was studied at 50 % r.H., while expansion was studied on mortars stored over an open water surface (> 99% r.H.). The bond behaviour was studied by pull-off tests according to DIN EN 1542 and by optical microscopy. The alkali-activated mortars exhibit hygric deformations much lower than the deformations of an established, commercial mortar for sewer maintenance that was tested as reference in parallel with the alkali-activated mortars. The bond behaviour of the alkali-activated mortars depends strongly on their mix-design and curing. Optical microscopy showed that in the mortars with lower bond strength, cracks developed in the mortar during curing. Mortars with appropriate mix-design and curing did not exhibit cracking, and their pull-off strength (up to >3 MPa) conformed to the requirements of relevant standards. T2 - International Conference on Sustainable Materials, Systems and Structures (SMSS 2019) CY - Rovinj, Croatia DA - 20.03.2019 KW - Alkali-activated materials KW - Repair mortars KW - Sewer repair KW - Hygric deformations KW - Bond strength PY - 2019 SN - 978-2-35158-225-1 VL - 3 SP - 103 EP - 110 PB - RILEM Publications CY - Paris AN - OPUS4-47587 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hofmann, Michael A1 - Moufid, M. A1 - El Bari, N. A1 - Tiebe, Carlo A1 - Bouchikhi, B. T1 - Testing of a developed multigas sensor system for outdoor odour nuisance monitoring N2 - This work presents the testing of a developed elec¬tronic nose for outdoor odour nuisance monitoring. The sensor system consists of a sampling system, a measuring cell equipped with commercially available low-cost gas sensor elements and a data acquisition system. The sensor testing showed that the developed prototype is able to distinguish, identify and partially quantify individual odorous substances like ethanol, ammonia and hydrogen sulphide. Ethanol and ammonia could even be detected below or near their odour threshold. T2 - ALLSENSORS 2019, The Fourth International Conference on Advances in Sensors, Actuators, Metering and Sensing CY - Athens, Greece DA - 24.02.2019 KW - Electronic nose KW - Outdoor odour KW - Machined olfaction KW - Sensor testing PY - 2019 UR - https://www.thinkmind.org/index.php?view=article&articleid=allsensors_2019_2_40_70065 SN - 978-1-61208-691-0 SN - 2519-836X SP - 27 EP - 28 PB - The ThinkMind Digital Library AN - OPUS4-47505 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bulling, Jannis A1 - Prager, Jens T1 - Bestimmung der Rissgeometrie bei der zerstörungsfreien Ultraschallprüfung mit geführten Wellen N2 - In der zerstörungsfreien Prüfung werden in zunehmendem Maße geführte Ultraschallwellen zur Lokalisation von Fehlstellen genutzt. Geführte Ultraschallwellen zeichnen sich dadurch aus, dass sie große Distanzen innerhalb des zu prüfenden Bauteiles zurücklegen können. Das Ultraschallwellenfeld setzt sich dabei aus verschieden Moden zusammen. Etablierte Prüfverfahren mit geführten Wellen ermitteln häufig nur die Position der Fehlstelle, wobei die Laufzeiten der reflektierten Signale ausgewertet wird. Modenumwandlung bleibt dabei zumeist unberücksichtigt. Die Charakterisierung der Fehlstelle, zum Beispiel hinsichtlich der Länge eines Risses, ist dagegen herausfordernd. Aussagekräftige Zusammenhänge zwischen der Dimension oder Geometrie der Fehlstelle und ihrer Interaktion mit der Ultraschallwelle zu finden, ist Teil aktueller Forschung. Insbesondere eine Betrachtung der Moden höherer Ordnung und deren Amplitudenverhältnisse kann beim Aufspüren dieser Zusammenhänge hilfreich sein. Im Beitrag werden zunächst die Zusammenhänge zwischen den beiden fundamentalen Moden in einer isotropen Platte und der Länge eines Risses untersucht. Aus den Ergebnissen wird ein inverses Verfahren motiviert. Ein Algorithmus wird vorgestellt, der die Risslänge im Modell solange variiert, bis er die modalen Zusammenhänge einer Vorgabe oder einer Messung rekonstruiert. Die eingesetzte Scaled Boundary Finite Element Method ermöglicht dabei eine sehr kurze Rechenzeit in jeden Optimierungsschritt. Zusätzlich ermöglicht die Methode eine Auswertung der modalen Zusammenhänge ohne Postprocessing, was die Rechenzeiten weiter verkürzt. T2 - DAGA 2019 - 45. Jahrestagung für Akustik CY - Rostock, Germany DA - 18.03.2019 KW - Geführte Ultraschallwellen KW - Zerstörungsfreien Prüfung KW - Scaled Boundary Finite Element Method PY - 2019 VL - 45 SP - 1063 PB - Deutsche Gesellschaft für Akustik e.V. AN - OPUS4-47783 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kotschate, Daniel A1 - Gaal, Mate T1 - Plasma-akustische Wechselwirkungen von Mikrohohlkathodenentladungen N2 - Während des Entladungsprozesses interagieren Mikrohohlkathodenentladungen (engl. micro hollow cathode discharges) durch verschiedenste physikalische Phänomene mit ihrer Umgebung. Analog zu Funken- und Koronaentladung treten neben den optischen Erscheinungen auch akustische Wechselwirkungen bis in den Ultraschallbereich auf. Diese Wechselwirkungen sind bisher jedoch nur selten Gegenstand der Forschung gewesen. Durch elektro-chemischen Prozesse und die Stromdichteverteilung während des Zündvorgangs erfährt das angrenzende Fluid eine, durch den thermoakustischen Effekt hervorgerufene, rapide Dichteänderung und erzeugt somit eine akustische Emission. Dieser Beitrag gibt einen Überblick über den letzten Stand der akustischen Beschreibung der Mikrohohlkathode. Weiterhin wird anhand von Anwendungsbeispielen, wie der Charakterisierung von akustischen Sensoren, sowie der Nutzung innerhalb der zerstörungsfreien Werkstoffprüfung, die Nutzung dieser Entladungsart präsentiert. Darüber hinaus erlaubt die Kenntnis hinsichtlich der akustischen Eigenschaften der Entladung wichtige Rückschlüsse im Rahmen der Plasmadiagnostik. T2 - 45. Jahrestagung für Akustik (DAGA 2019) CY - Rostock, Germany DA - 18.03.2019 KW - Micro hollow cathode discharge KW - Atmospheric pressure plasma PY - 2019 SP - 1049 EP - 1051 AN - OPUS4-47790 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wachtendorf, Volker A1 - Geburtig, Anja A1 - Trubiroha, P. ED - Ziegahn, K.-F. T1 - Messung der effektiven UV-Bestrahlung bei der Bewitterung von Polymeren N2 - Bei der Bestrahlung und Bewitterung von polymeren Werkstoffen wird die Degradation durch eine Absorption von Strahlung initiiert und meistens durch weitere Klimagrößen, wie z.B. Wärme, Feuchte und atmosphärische Gase beeinflusst. Die Messung einer effektiven Bestrahlungsstärke und ihre zeitliche Integration sind deshalb von großer Bedeutung und zwar sowohl für die Kontrolle der Funktion des Bewitterungs- oder Bestrahlungsgerätes als auch als zusätzliche Angabe der wirkenden Beanspruchung. Photochemische Prozesse werden beim Sehen oder allgemeiner bei Farbstoffen schon durch sichtbare (VIS) Strahlung, dagegen bei der Erythembildung der Haut und der Photodegradation von Polymeren erst durch die energiereicheren Photonen der ultravioletten (UV) Strahlung initiiert. Die spektrale Empfindlichkeit des Auges und die Erythembildung sind im VIS- bzw. UV-Bereich sehr stark wellenlängenabhängig, was durch die Angabe der mit der spektralen Hellempfindlichkeit V(λ) des Auges bewerteten VIS-Strahlung in Lux (lx) bzw. die mit der Erythem-Wirkfunktion Serythem bewertete UV Strahlung als dimensionsloser UV-Index berücksichtigt wird. Spektrale Empfindlichkeiten. Die Photodegradation von Polymeren ist im UV-Bereich ebenfalls stark wellenlängenabhängig, was bisher bei der radiometrischen UV-Messung nicht berücksichtigt wurde. Seit Mitte der 70er Jahre, als die lx- bzw lxh- Messung bei der Strahlungsbeanspruchung langsam durch die Ermittlung der radiometrischen UV-Bestrahlungsstärke bzw. der UV-Bestrahlung im gesamten UV-Bereich abgelöst wurde, gab es hier bei der Bewitterungsprüfung keine weiteren Fortschritte auf dem Gebiet der Charakterisierung der Strahlungsbeanspruchung im UV-Bereich. Seit Jahren liegen zahlreiche Ergebnisse über die spektrale Empfindlichkeit von Photo-degradationsprozessen vor, die zeigen, dass die spektrale Empfindlichkeit im Bereich der Globalstrahlung an der kurzwelligen Grenze bei ca. 300 nm, am größten ist und im langwelligen UV-Bereich bei ca. 400 nm gegen Null geht. Die Messungen der radiometrischen Größen UV-Gesamtbestrahlungsstärke und UV-Gesamtbestrahlung erfasst deshalb über weite Wellenlängenbereiche Strahlungsanteile, die für die Photodegradation bedeutungslos sind und mittelt über potenziell bedeutsame Änderungen im kurzwelligen UV-Bereich hinweg. Es wird das Konzept eines neuen UV-Radiometers vorgestellt, dessen spektrale Empfindlichkeit einer mittleren spektralen Empfindlichkeit der Photodegradation von Polymeren entspricht. Die effektive UV-Bestrahlungsstärke und UV-Bestrahlung kann dadurch wesentlich genauer erfasst werden. T2 - 48. Jahrestagung der GUS 2019 CY - Stutensee, Germany DA - 27.03.2019 KW - UV-Bestrahlungsstärke PY - 2019 SN - 978-3-9818507-3-4 SP - 89 EP - 100 AN - OPUS4-47896 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Auersch, Lutz T1 - Vehicle-track-soil interaction and train-induced ground vibration – Theory and measurements in Germany, Switzerland and France N2 - Three measurement campaigns of train-induced ground vibrations are evaluated for the vehicle-track-soil interaction. Ground vibrations, track vibrations and vehicle vibrations have been measured for train passages and impulse excitation and compared with theoretical results. The soil and the track-soil system are calculated by wavenumber integrals. The influence of the vehicle is introduced by a substructure method. By comparing theory and measurement the different components of excitation force and ground vibration can be analysed, the quasi-static excitation, track-alignment errors, the out-of-roundness of wheels, the wheel and rail roughness, and moreover, scattered axle impulses and ineffective high-frequency parts of the wheelset accelerations and forces. T2 - Recent Advance in Structural Dynamics CY - Lyon, France DA - 15.04.2019 KW - Vehicle-track-soil interaction KW - Train-induced ground vibration KW - Vibration measurements PY - 2019 SP - 810 EP - 821 PB - University of Southampton CY - Southampton AN - OPUS4-47892 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Otremba, Frank A1 - Romero-Navarrete, José A. T1 - Experimental modeling of railway car wheel-forces during turning N2 - An experimental testing rig has been proposed to study the dynamic interaction between a liquid cargo and the carrying vehicle during turning maneuvers. The basic operational principle of the testing rig consists in simulating the lateral accelerations associated to turning maneuvers through the use of a tilt table. While the experimental capabilities of the testing rig include the analysis of the effects of the cars on the whole transport infrastructure, including sleepers and ballast, a first use of the rig considered the effect of sloshing cargo on the level of dynamic forces transmitted to the rails. Such test was used to validate a simplified theoretical approach consisting of a two degree-of-freedom double pendulum mechanical system, where a simple pendulum, representing the sloshing cargo, is articulated to the spring-supported vehicle chassis, which is modelled as an inverted torsional pendulum. While the theoretical results exhibit a high correlation with the experimental data, the main discrepancy between both outputs, relates with the frequency of the residual vibration, once the lateral acceleration input is ceased. Such difference in frequency, would imply an underestimation of the number of loading cycles to which the infrastructure is subjected. On the other hand, the peak values are within acceptable difference levels. T2 - IEEE/ASME Joint Rail Conference CY - Snowbird, Utah, USA DA - 09.04.2019 KW - Railway KW - Wheel-forces KW - Turning PY - 2019 SP - 1 EP - 8 PB - ASME AN - OPUS4-47880 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreier, Andy A1 - Liehr, Sascha A1 - Wosniok, Aleksander A1 - Krebber, Katerina T1 - Comparison of solution approaches for distributed humidity sensing in perfuorinated graded-index polymer optical fibers N2 - We compare four different sensing solutions suitable for distributed fiber optic humidity sensing in per uorinated graded-index polymer optical fibers (PFGI-POFs). Compared to silica fbers, polymer optical fibers over advantageous beneffits including signifficantly higher break down strain, fracture toughness and humidity sensitivity. Various humidity-related effects in PFGI-POFs have been reported in the last years including measured attenuation and length changes as well as Brillouin frequency and Bragg wavelength shifts. The four aforementioned methods could serve as a basis for distributed and quasi-distributed humidity sensing and are described here closely with an emphasis on plausible cross effects to temperature and strain. The main focus of this paper lies on the comparison of four approaches with regard to method complexity, sensitivity to humidity, spatial resolution, real-time capability and effort to compensate for cross effects. T2 - SPIE Optics + Optoelectronics CY - Prague, Czech Republic DA - 01.04.2019 KW - Distributed sensing KW - Humidity KW - Polymer optical fibre PY - 2019 SN - 978-1-5106-2723-9 DO - https://doi.org/10.1117/12.2522307 SN - 0277-786X SN - 1996-756X SP - 1102808-1 EP - 1102808-9 PB - SPIE AN - OPUS4-47844 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wasmer, Paul A1 - Bulling, Jannis A1 - Prager, Jens T1 - Entwicklung eines Ultraschallrohrsensors auf Basis phononischer Kristalle N2 - Die Messung von Flüssigkeitskonzentrationen in Rohrsystemen ist von großem Interesse für viele unterschiedliche Anwendungen. Die meisten Messsysteme sind jedoch nicht in der Lage, die Flüssigkeit direkt im Rohr zu untersuchen und es muss eine zusätzliche Vorrichtung, wie z.B. einem Bypass, angebracht werden, welche den Kontakt zwischen Flüssigkeit und Sensor ermöglicht. Um den Einbauaufwand gering zu halten und die Strömungseigenschaften des Rohres nicht zu beeinflussen, wird ein neuartiges Messsystem entwickelt, welches als Teil der Rohrwand ausgeführt werden kann. Dieses neuartige System ist angelehnt an die Idee der phononischen Kristallen (PnK). PnK’s bestehen im Allgemeinen aus einem Matrixmaterial, in welchem Streuzentren periodisch angeordnet sind. Dies führt beim Eintreffen einer akustischen Welle in definierten Frequenz-bereichen, sogenannter Bandlücken, zu zunehmender destruktiven Interferenz. Wird innerhalb einer solchen Bandlücke durch Einbringen einer flüssigkeitsgefüllten Kavität ein Resonanzverhalten erzeugt, kann dies genutzt werden, um die Flüssigkeit zu analysieren. Im Rahmen von Voruntersuchung wird zunächst das akustische Verhalten des PnK’s, welcher für die Sensorentwicklung genutzt werden soll, unter Vernachlässigung der Flüssigkeit ausführlich untersucht. Hierbei werden zunächst die Bandlücken ermittelt und das Übertragungsverhalten betrachtet. Dieses wird im Anschluss experimentell überprüft. T2 - DAGA 2019 - 45. Jahrestagung für Akustik CY - Rostock, Germany DA - 18.03.2019 KW - Phononischer Kristall KW - Ultraschall KW - Flüssigkeitssensor KW - Scaled Boundary Finite Element Method PY - 2019 SP - 1030 EP - 1033 AN - OPUS4-47780 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Beck, Uwe A1 - Griepentrog, Michael A1 - Hertwig, Andreas A1 - Hielscher, Stefan A1 - Weise, Matthias T1 - Auf dem Weg zu Industrie 4.0: Bestimmung von Messunsicherheitsbudgets in der Oberflächentechnik N2 - Vorgestellt wurde die Bestimmung von Messunsicherheitsbudgets für sehr unterschiedliche physikalische Größen, die in der Oberflächentechnik von hoher Relevanz sind: Stufenhöhe h, Schichtdicke d, Eindringhärte HIT und Haftfestigkeit. Die Unterschiede betreffen die Art der Prüfmethodik (optisch zerstörungsfrei vs. mechanisch invasiv/zerstörend), die laterale Größe des Integrationsgebietes der Messung (lokal: nano bis sub-mikro vs. global: mikro bis makro) und die Art der Bestimmung von Messunsicherheitsbudgets (physikalische Größen: direkt rückführbar; Werkstoffkenngröße: genormt; Systemkenngröße: genormt). Im Rahmen von Industrie 4.0 werden ausgehend der geforderten Spezifikation des beschichteten Produkts (Mittelwert mit Vertrauensbereich oder Mindestwert) durchgehende Toleranzbänder zur Oberflächenmodifizierung/Beschichtung des Substrats, einhergehend mit Prozessfenstern, die diese Toleranzbänder garantieren, erforderlich, die zuverlässig erfasst werden müssen. Die Frage der anzuwendenden Mess- und Prüftechnik und die damit notwendige Betrachtung von Messunsicherheitsbudgets ist für die Digitalisierung von Konditionierungs-, Zustands-, Regel- und Steuergrößen unverzichtbar. Mit Blick auf die Einhaltung von Prozessfenstern und die dafür notwendige Prozessführung wird technologisches Kern-Know-how digitalisiert, das es unbedingt zu schützen gilt. Nur lokale Netze können diese Sicherheit garantieren, in globalen Netzen ist die Datensicherheit bestenfalls maximierbar T2 - 14. ThGOT Thementage Grenz- und Oberflächentechnik und 6. Kolloquium Dünne Schichten in der Optik CY - Zeulenroda, Germany DA - 12.03.2019 KW - Oberflächentechnik KW - Messunsicherheit KW - Messtechnik KW - Prüftechnik KW - Haftfestigkeit PY - 2019 SN - 978-3-00-058187-8 VL - 2019 SP - 1 EP - 10 AN - OPUS4-47670 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kratzig, Andreas A1 - Bettge, Dirk A1 - Le, Quynh Hoa A1 - Bäßler, Ralph A1 - Kranzmann, Axel T1 - Interaction of Oxidizing and Reductive Components in CO2 Streams with Transport Pipeline Steel X70 at High Pressure and Low Temperature N2 - Specific amounts of oxidizing and reductive impurities as well as some moisture were added to dense phase CO2 to replicate CO2 streams from sources in a CCS pipeline network. Due to the moisture content being only 50 ppmV no visible acid condensation took place. To simulate stress conditions at the inside pipeline surface due to fluid pressure (10 MPa) specimens were preloaded using a load frame. Experiments conducted at 278 K and at 313 K revealed the highest corrosion rate at lower temperature. Corrosive effect of impurities was strongest applying mixed atmosphere, containing oxidizing and reductive components, closely followed by CO2 streams with pure oxidizing character. By far, the lowest corrosion rate (10x lower) resulted from reductive atmosphere. In general, at constant temperature and pressure the CO2 stream composition strongly influences the morphology, thickness and composition of the corrosion products. Applying oxidizing or mixed impurities, iron hydroxides or oxides (e.g. goethite, hematite) occur as dominating corrosion products, capable to incorporate different amounts of sulfur. In contrast, using reductive atmosphere very thin corrosion layers with low crystallinity were developed, and phase identification by XRD was unfeasible. SEM/EDX analysis revealed the formation of Fe-O compounds, most likely attributed to the oxygen partial pressure in the system induced by CO2 (≥0.985 volume fraction) and volatile H2O. In addition to the surface covering corrosion layer, secondary phases had grown locally distributed on top of the layer. These compounds are characteristic for the applied atmosphere and vary in number, shape and chemical composition. T2 - 14th Greenhouse Gas Control Technologies Conference (GHGT-14) CY - Melbourne, Australia DA - 21.10.2018 KW - CCS KW - CO2 Corrosion KW - Pipelines PY - 2019 UR - https://ssrn.com/abstract=3365756 VL - 2019 SP - 1 EP - 15 AN - OPUS4-49711 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Legall, Herbert A1 - Schwanke, Christoph A1 - Bonse, Jörn A1 - Krüger, Jörg T1 - X-ray emission during ultrashort pulse laser processing N2 - The industrial use of ultrashort laser pulses has made considerable progress in recent years. The reasons for this lie in the availability of high average powers at pulse repetition rates in the several 100 kHz range. The advantages of using ultrashort laser pulses in terms of processing precision can thus be fully exploited. However, high laser intensities on the workpiece can also lead to the generation of unwanted X-rays. Even if the emitted X-ray dose per pulse is low, the accumulated X-ray dose can become significant for high-repetition-rate laser systems so that X-ray exposure safety limits must be considered. The X-ray emission during ultrashort pulse laser processing was investigated for a pulse duration of 925 fs at 1030 nm wavelength and 400 kHz repetition rate. Industrially relevant materials such as steel,aluminum and glass were treated. Tungsten served as reference. X-ray spectra were recorded, and X-ray dose measurements were performed for laser treatment in air. For laser intensities > 2 × 10^13 W/cm2, X-ray doses exceeding the regulatory exposure limits for members of the public were found. Suitable X-ray protection strategies are proposed. T2 - SPIE Photonics West CY - San Francisco, USA DA - 02.02.2019 KW - Laser-induced X-ray emission KW - Ultrashort laser material interaction KW - Radiation protection PY - 2019 SN - 978-1-5106-2459-7 DO - https://doi.org/10.1117/12.2516165 SN - 0277-786X SN - 1996-756X VL - 10908 SP - 1090802-1 EP - 1090802-7 PB - SPIE - The international society for optics and photonics CY - Bellingham, WA, USA AN - OPUS4-47510 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Florian, Camilo A1 - Kirner, Sabrina V. A1 - Krüger, Jörg A1 - Bonse, Jörn T1 - Quo vadis LIPSS? – Applications of laser-induced periodic surface structures N2 - Laser-induced periodic surface structures (LIPSS, ripples) are a universal phenomenon that can be observed on almost any material after the irradiation by linearly polarized laser beams, particularly when using ultrashort laser pulses with durations in the femtosecond to picosecond range. During the past years significantly increasing industrial and research activities have been reported in the field of LIPSS, since their generation in a single-step process provides a simple way of nanostructuring and surface functionalization towards the control of optical, mechanical or chemical surface properties. In this contribution the mechanisms of formation and current trends and applications of LIPSS are reviewed, including the colorization of technical surfaces, the control of surface wetting properties, the mimicry of the natural texture of animals, the tailoring of surface colonization by bacterial biofilms, the advancement of leadless medical pacemakers, and the improvement of the tribological performance of nanostructured metal surfaces. T2 - 11. Mittweidaer Lasertagung CY - Mittweida, Germany DA - 13.11.2019 KW - Laser-induced periodic surface structures (LIPSS) KW - Femtosecond laser ablation KW - Surface functionalization KW - Applications PY - 2019 VL - 3/1 SP - 41 EP - 43 PB - Hochschule Mittweida CY - Mittweida AN - OPUS4-49673 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -