TY - CONF A1 - Nolze, Gert T1 - Introduction to PowderCell N2 - The presentation give a short introduction into the free-available software PowderCell (BAM)for the simulation of X-ray diffraction patterns of polycrystalline materials. T2 - PowderCell Users meeting CY - Joinville, Brazil DA - 19.10.2015 KW - X-ray diffraction KW - Simulation KW - Structure viewer KW - Subgroup relationships PY - 2015 AN - OPUS4-37791 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Vos, M. A1 - Winkelmann, Aimo A1 - Nolze, Gert T1 - Element-specific Kikuchi patterns of Rutile JF - Ultramicroscopy N2 - The kinetic energy of keV electrons backscattered from a rutile (TiO2) surface depends measurably on the mass of the scattering atom. This makes it possible to determine separately the angular distribution of electrons backscattered elastically from either Ti or O. Diffraction effects of these backscattered electrons inside the rutile crystal lead to the formation of Kikuchi patterns. The element-resolved Kikuchi patterns of Ti and O differ characteristically, but each can be described fairly well in terms of the dynamical theory of diffraction. Qualitatively, much of the differences can be understood by considering the relative arrangement of the Ti and O atoms with respect to planes defined by the crystal lattice. KW - Electron Rutherford backscattering KW - TiO2 KW - Kikuchi pattern KW - EBSD pattern KW - Simulation PY - 2015 DO - https://doi.org/10.1016/j.ultramic.2015.04.018 SN - 0304-3991 VL - 156 SP - 50 EP - 58 AN - OPUS4-37787 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nolze, Gert T1 - Simulation of powder diffraction patterns N2 - The theory of powder diffraction simulation is explained at the example of PowderCell, a free-available software of BAM. T2 - PowderCell Users meeting CY - Joinville, Brazil DA - 21.09.2015 KW - Powder diffraction KW - X-ray diffraction KW - Phase analysis KW - Simulation PY - 2015 AN - OPUS4-37789 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Winkelmann, Aimo A1 - Nolze, Gert T1 - Orientation mapping of non-centrosymmetric crystals T2 - RMS Electron backscatter diffraction meeting T2 - RMS Electron backscatter diffraction meeting CY - Glasgow, UK DA - 30.03.2015 KW - EBSD KW - Cross-correlation KW - Non-centrosymmetry KW - Simulation PY - 2015 SP - 1 AN - OPUS4-33030 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maack, Stefan A1 - Kneib, G. T1 - Elastic wave propagation of ultrasound in bituminous road surfaces – simulations and measurements N2 - Maintenance costs of road infrastructure are increasing steadily. Adverse environmental impacts on infrastructure get more and more important as well. Therefore, it is important to determine how limited financial resources can be directed with an optimum pay-out. The present study takes first steps towards the usage of low-frequency ultrasound as a tool to evaluate the road condition. T2 - International Symposium Non-Destructive Testing in Civil Engineering 2015 CY - Berlin, Germany DA - 15.09.2015 KW - Wave propagation KW - Ultrasonic KW - NDT KW - Simulation PY - 2015 AN - OPUS4-38837 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zencker, Uwe A1 - Qiao, Linan A1 - Völzke, Holger T1 - Dynamic finite element analysis of cask handling accidents at storage sites T2 - ASME 2015 Pressure vessels & piping conference - PVP2015 (Proceedings) N2 - The safety assessment of casks for radioactive material at interim storage facilities or in final repositories includes the investigation of possible handling accidents if clearly defined test conditions are not available from the regulations. Specific handling accidents usually are the drop of a cask onto the transport vehicle or the floor as well as the collision with the wall of the storage building or another cask. For such load cases an experimental demonstration of cask safety would be difficult. Therefore, numerical analyses of the entire load scenario are preferred. The lessons learnt from dynamic finite element analyses of accident scenarios with thick-walled cubical containers or cylindrical casks are presented. The dependency of calculation results on initial and boundary conditions, material models, and contact conditions is discussed. Parameter sets used should be verified by numerical simulation of experimentally investigated similar test scenarios. On the other hand, decisions have to be made whether a parameter or property is modeled in a realistic or conservative manner. For example, a very small variation of the initial impact angle of a container can cause significantly different stresses and strains. In sophisticated cases an investigation of simpler limit load scenarios could be advantageous instead of analyzing a very complicated load scenario. T2 - ASME 2015 Pressure vessels & piping conference - PVP2015 CY - Boston, Massachusetts, USA DA - 19.07.2015 KW - Finite element method KW - Simulation KW - Cask handling accident KW - Interim storage PY - 2015 SN - 978-0-7918-5702-1 SP - Paper 45606, 1 EP - 10 AN - OPUS4-34937 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zencker, Uwe A1 - Qiao, Linan A1 - Völzke, Holger T1 - Strategies for numerical modelling of metal gaskets in transport and storage casks T2 - RAMTRANSPORT 2015 - International conference on the radioactive materials transport and storage (Proceedings) N2 - Metal gaskets in the lid system of transport and storage casks for radioactive material have to guarantee leak-tightness and safe enclosure of the radioactive inventory under normal and accident conditions during transport, in case of accidents and for the longterm interim storage. For safety assessments by nurnerical simulation of the thermomechanical behaviour of a lid system with metal gaskets, the finite element method offers three options to use: i) special gasket elements, ii) complex three-dimensional modeHing with solid elements, and iii) a simplified axisymmetric approach. Gasket elements can be adjusted by many parameters, but they give only a global representation of the experimentally observed gasket behaviour. For calculations of the entire cask including the lid system with gaskets, nonetheless this approach is recommended. To investigate the hardly measurable impact behaviour in detail or to extrapolate the long-term behaviour, a local modeHing of all parts of a gasket and their interactions with effects like elastic-plastic deformation, creep, relaxation, and friction is necessary. The three-dimensional model can describe the change of contact area between outer jacket of the gasket and flange dependent on the load conditions, what overcomes an essential limitation of special gasket elements. To simplify the problern of investigating the underlying physical effects, an axisymmetric lid system can be modelled with axisymmetric finite elements. Usually an approximation is only necessary for the helical spring of a metal gasket. This paper explains basic ideas for an adequate finite element simulation of cask lid systems with metal gaskets and their thermo-mechanical behaviour under specific load scenarios. T2 - RAMTRANSPORT 2015 - International conference on the radioactive materials transport and storage CY - Oxford, UK DA - 19.05.2015 KW - Metal gasket KW - Finite element method KW - Simulation PY - 2015 SP - Paper RAM15-27, 1-9 AN - OPUS4-34938 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kempel, Florian A1 - Schartel, Bernhard A1 - Marti, J.M. A1 - Butler, K.M. A1 - Rossi, R. A1 - Idelsohn, S.R. A1 - Onate, E. A1 - Hofmann-Böllinghaus, Anja T1 - Modelling the vertical UL 94 test: competition and collaboration between melt dripping, gasification and combustion JF - Fire and materials N2 - An experimental and numerical investigation of the effect of bisphenol A bis(diphenyl phosphate) (BDP) and polytetrafluoroethylene (PTFE) on the fire behaviour of bisphenol A polycarbonate/acrylonitrile butadiene styrene (PC/ABS) in the vertical UL 94 scenario is presented. Four PC/ABS blends were discussed, which satisfy different UL 94 classifications due to the competing effects of gasification, charring, flame inhibition and melt flow/dripping. For numerical investigation, the particle finite element method (PFEM) is used. Its capability to model the complex fire behaviour of polymers in the UL 94 is analysed. The materials' properties are characterised, in particular the additives impact on the dripping behaviour during thermal exposure. BDP is an efficient plasticiser; adding PTFE prevents dripping by causing a flow limit. PFEM simulations reproduce the dripping and burning behaviour, in particular the competition between gasification and dripping. The thermal impact of both the burner and the flame is approximated taking into account flame inhibition, charring and effective heat of combustion. PFEM is a promising numerical tool for the investigation of the fire behaviour of polymers, particularly when large deformations are involved. Not only the principal phenomena but also the different UL 94 classifications and the extinction times are well predicted. KW - Melt dripping KW - UL 94 KW - Particle finite element method (PFEM) KW - Simulation KW - Bisphenol A polycarbonate/acrylonitrile butadiene styrene (PC/ABS) KW - Polytetrafluoroethylene (PTFE) KW - Bisphenol A bis(diphenyl phosphate) (BDP) PY - 2015 DO - https://doi.org/10.1002/fam.2257 SN - 0308-0501 SN - 1099-1018 VL - 39 IS - 6 SP - 570 EP - 584 PB - Heyden CY - London AN - OPUS4-34285 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geoerg, Paul A1 - Rost, M. A1 - Krause, U. A1 - Hofmann-Böllinghaus, Anja T1 - Vergleichende Untersuchung zur Personensicherheit am Beispiel eines Seminarraumes T2 - 4. Magdeburger Brand- und Explosionsschutztag / 3. vfdb-Workshop Brandschutzforschung N2 - Um den Anforderungen der Bauordnung an den Brandschutz für Gebäude gerecht zu werden, sind bauliche Anlagen so zu errichten und zu betreiben, dass der Entstehung eines Brandes und der Ausbreitung von Feuer und Rauch vorgebeugt, die Rettung von Menschen und Tieren sowie wirksame Löscharbeiten ermöglicht werden. Hierbei besteht, einer steigenden Komplexität sowie einem differenzierten Nutzungskonzept öffentlicher Gebäude geschuldet, häufig die Notwendigkeit von normativen Vorgaben abzuweichen und dennoch ein gleichwertiges Sicherheitsniveau nachzuweisen. Es werden Personensimulationsmodelle eingesetzt, die einerseits das Vorhandensein eines Schutzzielniveaus durch die Abbildungen von Personenbewegungen nachweisen können und andererseits durch Parametervariation eine szenarienabhängige Betrachtung ermöglichen. Der vorliegende Beitrag vergleicht die Ergebnisse einer kleinskaligen Evakuierungsübung mit drei mikroskopischen Personensimulationsmodellen und geht der Frage nach der Aussagekraft dieser Bewertungsmethode nach. Es zeigt sich, dass die alleinige Betrachtung absoluter Entleerungszeiten keine zuverlässige Beurteilungsgrundlage für das komplexe Schutzziel Personensicherheit darstellt. T2 - 4. Magdeburger Brand- und Explosionsschutztag / 3. vfdb-Workshop Brandschutzforschung CY - Magdeburg, Germany DA - 26.03.2015 KW - Evakuierung KW - Routenwahl KW - Fußgänger KW - Sicherheit KW - Simulation PY - 2015 SN - 978-3-00-048960-0 SP - 1 EP - 13 AN - OPUS4-33123 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geoerg, Paul A1 - Hofmann-Böllinghaus, Anja A1 - Krause, U. T1 - Comparative study of evacuation dynamics using a lecturer room T2 - 6th international symposium on human behaviour in fire 2015 (Proceedings) N2 - Computer simulation tools were used to evaluate pedestrian movement. This study compares the reliability of three simulation tools and the calculation method by Predtetschenski und Milinski with a controlled evacuation exercise of a lecturer room. The comparison shows that each simulation tool used underestimate the total evacuation time and that an indicator for a low level of fitness does not necessarily lead to a long evacuation time. Results revealed that calibration of simulation tools is required to model heterogeneous population properly. Therefore, further experiments with a realistic, heterogeneous composition of participants have to be made. T2 - 6th international symposium on human behaviour in fire 2015 CY - Cambridge, UK DA - 28.09.2015 KW - Pedestrian KW - Simulation KW - Evacuation KW - Heterogeneous groups PY - 2015 SN - 978-0-9933933-0-3 SP - 667 EP - 670 AN - OPUS4-34549 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -