TY - JOUR A1 - Smekhova, A. A1 - Kuzmin, A. A1 - Siemensmeyer, K. A1 - Abrudan, R. A1 - Reinholz, Uwe A1 - de Oliveira Guilherme Buzanich, Ana A1 - Schneider, M. A1 - Laplanche, G. A1 - Yusenko, Kirill T1 - Inner relaxations in equiatomic single-phase high-entropy Cantoralloy N2 - The superior properties of high-entropy multi-functional materials are strongly connected with their atomic heterogeneity through many different local atomic interactions. The detailed element-specific studies on a local scale can provide insight into the primary arrangements of atoms in multicomponent systems and benefit to unravel the role of individual components in certain macroscopic properties of complex compounds. Herein, multi-edge X-ray absorption spectroscopy combined with reverse Monte Carlo simulations was used to explore a homogeneity of the local crystallographic ordering and specific structure relaxations of each constituent in the equiatomic single-phase facecentered cubic CrMnFeCoNi high-entropy alloy at room temperature. Within the considered fitting approach, all five elements of the alloy were found to be distributed at the nodes of the fcc lattice without any signatures of the additional phases at the atomic scale and exhibit very close statistically averaged interatomic distances (2.54 – 2.55 Å) with their nearest-neighbors. Enlarged structural displacements were found solely for Cr atoms. The macroscopic magnetic properties probed by conventional magnetometry demonstrate no opening of the hysteresis loops at 5 K and illustrate a complex character of the long-range magnetic order after field-assisted cooling in ± 5 T. The observed magnetic behavior is assigned to effects related to structural relaxations of Cr. Besides, the advantages and limitations of the reverse Monte Carlo approach to studies of multicomponent systems like high-entropy alloys are highlighted. KW - Magnetism KW - High-entropy alloys KW - Reverse Monte Carlo (RMC) KW - Element-specific spectroscopy KW - Extended X-ray absorption fine structure (EXAFS) KW - X-ray absorption near edge structure (XANES) PY - 2022 DO - https://doi.org/10.1016/j.jallcom.2022.165999 SN - 0925-8388 VL - 920 SP - 1 EP - 31 PB - Elsevier AN - OPUS4-55457 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Herbst, Tristan T1 - Konzept zur ganzheitlichen Nachhaltigkeitsbewertung des Abbruchs und der Aufbereitung von Mauerwerk N2 - Mit der vorliegenden Arbeit wurde ein methodisches Konzept zur ganzheitlichen Nachhaltigkeitsbewertung des Abbruchs und der Aufbereitung von Mauerwerk bereitgestellt. Das Bewertungskonzept ermöglicht einen ganzheitlichen Vergleich verschiedener Szenarien für den Abbruch und die Aufbereitung von Mauerwerk unter Berücksichtigung der Anwendung von Mauerwerkbruch und aussortierter Fremdstoffe zur Verwertung. Es kombiniert die Kosten-Wirksamkeitsanalyse, die Stoffflussanalyse, die Ökobilanzierung, die Betrachtung sozialer Aspekte und Wirtschaftlichkeitsbetrachtungen bei gleichzeitiger Berücksichtigung der Materialqualitäten. Das Bewertungskonzept basiert im Kern auf der Kosten-Wirksamkeitsanalyse (KWA) mit der Erweiterung um das Gesamtwirksamkeitswert-Kosten-Verhältnis. Hiermit können sowohl monetäre als auch nicht monetäre Effekte beurteilt werden. Ausgangspunkt der KWA ist ein klar definiertes Zielsystem. Im vorliegenden Fall wurden aus der EU-Abfallrahmenrichtlinie, dem Kreislaufwirtschaftsgesetz und der EU-Bauproduktenverordnung die vier Generalziele „Mensch und Umwelt“, „Ressourcenschonung“, „Ausreichende Materialqualität“ sowie „Wirtschaftlichkeit“ abgeleitet. Die Generalziele "Mensch und Umwelt" und "Ressourcenschonung" wurden weiter in Hauptziele, Ziele und Unterziele unterteilt. Die Quantifizierung und Beurteilung dieser beiden Generalziele erfolgt im Rahmen der Wirksamkeitsanalyse. Zur Quantifizierung der abstrakten Ziele wurden konkrete und messbare Zielkriterien ausgewählt, die üblicherweise bei der Ökobilanzierung und sozialorientierten Betrachtungen verwendet werden, z. B. Umweltauswirkungen, Material- und Energieverbrauch. Nach Ermittlung einer Gesamtwirksamkeit und den anfallenden Kosten für jedes Szenario wird das Gesamtwirksamkeit-Kosten-Verhältnis je Szenario errechnet. Dieses Verhältnis bildet die Grundlage für die abschließende Reihung der untersuchten Szenarien entsprechend ihrer nachhaltigkeitsbezogenen Wertigkeit im Sinne der europäischen und deutschen Kreislaufwirtschaft. Mit dem Konzept wird zukünftigen Nutzern eine strukturierte und methodische Bewertungsgrundlage als Planungsinstrument für Abbruchprojekte an die Hand gegeben. Gleichzeitig werden die Nutzer für bestehende Gestaltungsvarianten für den Abbruch und die Aufbereitung von Mauerwerk sowie für die vielfältigen Anwendungsmöglichkeiten von Mauerwerkbruch sensibilisiert. T3 - BAM Dissertationsreihe - 151 KW - Nachhaltigkeit KW - Kosten- und Wirksamkeitsanalyse KW - Mauerwerkbruch KW - Abbruch KW - Aufbereitung PY - 2016 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-384853 SN - 978-3-9817853-8-8 SN - 1613-4249 VL - 151 SP - 1 EP - 146 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-38485 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Oberleitner, Lidia T1 - Immunochemical determination of caffeine and carbamazepine in complex matrices using fluorescence polarization N2 - Pharmacologically active compounds are omnipresent in contemporary daily life, in our food and in our environment. The fast and easy quantification of those substances is becoming a subject of global importance. The fluorescence polarization immunoassay (FPIA) is a homogeneous mix-and-read format and a suitable tool for this purpose that offers a high sample throughput. Yet, the applicability to complex matrices can be limited by possible interaction of matrix compounds with antibodies or tracer. Caffeine is one of the most frequently consumed pharmacologically active compounds and is present in a large variety of consumer products, including beverages and cosmetics. Adverse health effects of high caffeine concentrations especially for pregnant women are under discussion. Therefore, and due to legal regulations, caffeine should be monitored. Automated FPIA measurements enabled the precise and accurate quantification of caffeine in beverages and cosmetics within 2 min. Samples could be highly diluted before analysis due to high assay sensitivity in the low μg/L range. Therefore, no matrix effects were observed. The antiepileptic drug carbamazepine (CBZ) is discussed as a marker for the elimination efficiency of wastewater treatment plants and the dispersion of their respective effluents in surface water. The development of a FPIA for CBZ included the synthesis and evaluation of different tracers. Using the optimum tracer CBZ-triglycine-5-(aminoacetamido) fluorescein, CBZ concentrations in surface waters could be measured on different platforms: one sample within 4 min in tubes or 24 samples within 20 min on microtiter plates (MTPs). For this study, a commercially available antibody was used, which led to overestimations with recovery rates up to 140% due to high cross-reactivities towards CBZ metabolites and other pharmaceuticals. For more accurate CBZ determination, a new monoclonal antibody was produced. In this attempt, methods for improving the monitoring during the production process were successfully applied, including feces screening and cell culture supernatant screening with FPIA. The new monoclonal antibody is highly specific for CBZ and showed mostly negligible cross-reactivities towards environmentally relevant compounds. Measurements at non-equilibrium state improved the sensitivity and selectivity of the developed FPIA due to slow binding kinetics of the new antibody. Additionally, this measure enables for CBZ determination over a measurement range of almost three orders of magnitude. The comprehensively characterized antibody was successfully applied for the development of sensitive homogeneous and heterogeneous immunoassays. The new antibody made the development of an on-site measurement system for the determination of CBZ in wastewater possible. After comprehensive optimization, this automated FPIA platform allows the precise quantification of CBZ in wastewater samples only pre-treated by filtration within 16 min. Recovery rates of 61 to 104% were observed. Measurements in the low μg/L range are possible without the application of tedious sample preparation techniques. Different FPIA platforms including MTPs, cuvettes and tubes were successfully applied. For the choice of the right format, the application field should be considered, e.g. desired sample throughput, usage for optimization or characterization of antibodies or if a set-up for routine measurements is sought for. For high sample throughput and optimization, FPIA performance on MTPs is advantageous. The best results for the application to real samples were obtained using kinetic FP measurements in cuvettes. T3 - BAM Dissertationsreihe - 154 KW - Antibody KW - Coffee KW - ELISA KW - Fluorophore tracer KW - Wastewater PY - 2016 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-392506 SN - 978-3-9818270-2-6 SN - 1613-4249 VL - 154 SP - 1 EP - 124 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-39250 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Drzymala, Sarah T1 - Instrumental analysis, metabolism and toxicity of cis- and trans-zearalenone and their biotransformation products N2 - Trans-Zearalenone(ZEN)is a non-steroidal estrogenic mycotoxin which frequently contaminates cereal grains worldwide. Ingestion of food and feed containing ZEN causes numerous mycotoxicoses in animals and possibly humans with pronounced estrogenic effects. Due to the trans-configurated double bond, ZEN isomerizes to the cis-configuration upon the influence of light. This work investigates the instrumental analysis, metabolism and toxicity of ZEN and cis- ZEN. The first part focused on the determination of ZEN in edible oils. Due to a maximum level of 400 µg/kg ZEN in the European Union (EU), reliable analytical methods are needed. A comprehensive method comparison proved dynamic covalent hydrazine chemistry (DCHC) to be the most suitable approach. Thus, an automated solid phase extraction (SPE) coupled online to high performance liquid chromatography (HPLC) was developed with the novelty of a covalent SPE step comprising the DCHC principle. The automated online system allows an accurate, selective and reliable quantification of ZEN in edible oils in compliance with EU performance criteria while significantly reducing workload and thereby personnel costs. In contrast to ZEN, reference standards and analytical methods are missing for cis- ZEN which causes a lack of data on the occurrence, fate and risks of cis-ZEN. Therefore, a native and an isotopically labeled cis-ZEN standard were synthesized and implemented in an existing stable isotope dilution analysis HPLC tandem mass spectrometry (HPLC-MS/MS) method. Using this method, a large extent of cis-ZEN formation was observed for ZEN contaminated maize germ oils when exposed to daylight which confirms that cis-ZEN can be a relevant food contaminant and should be considered in the analysis of food and feed. Furthermore, this work investigated the in vitro phase I metabolism of ZEN and cis-ZEN in rat and human liver microsomes by using HPLC-MS and -MS/MS analyses. The metabolic pathways of cis-ZEN were found to be essentially similar to ZEN including reduction and oxidation reactions generating α- and β-cis- zearalenol as well as 13- and 15-OH-cis-ZEN. A previously unidentified oxidative metabolic pathway for both isomers of ZEN results in the formation of cis-ZEN-11,12-oxide and ZEN-11,12-oxide in human liver microsomes. The estrogenicity of cis-ZEN and its reductive metabolites was assessed using the E-Screen assay. cis-ZEN proved to be slightly more estrogenic than ZEN. Biotransformation of cis-ZEN to β-cis-ZEL corresponds to a detoxification, whereas metabolism to α-cis-ZEL resembles a metabolic activation as its estrogenicity considerably exceeds that of cis-ZEN. The catecholic metabolites can be expected to show a decreased estrogenicity as demonstrated for 15-OH- ZEN. Independent of the estrogenic effects, the catecholic and epoxidic metabolites identified in this work can be expected to act genotoxic and carcinogenic. The epoxides in particular could fundamentally change the widely accepted view of ZEN causing adverse effects exclusively through endocrine disrupting actions. T3 - BAM Dissertationsreihe - 152 KW - Hydrazinchemie KW - Isotopenstandard KW - SPE-HPLC Automatisierung KW - Zearalenon KW - Isomerisierung PY - 2016 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-386016 SN - 978-3-9817853-9-5 SN - 1613-4249 VL - 152 SP - 1 EP - 160 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-38601 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Bronsert, Jeffrey T1 - Numerische Modellierung der Fahrzeug-Fahrweg-Wechselwirkung an Eisenbahnfahrwegen und ihre Anwendung im Brückenübergangsbereich N2 - Im Mittelpunkt der vorliegenden Arbeit steht die numerische Modellierung der Fahrzeug-Fahrweg-Wechselwirkung von Eisenbahnfahrwegen, die auch für Fahrwege mit einer Diskontinuität einsetzbar ist. Der Fokus wurde hier auf Fahrwege mit einem Brückenbauwerk gelegt, weil es an den Übergängen zu einer erhöhten Beanspruchung kommt. Daher wurde für den Fahrweg mittels der Finiten Elemente Methode (FEM) ein dreidimensionales Modell mit einer Lösung im Zeitbereich entwickelt, das die wesentlichen Elemente des Schienenverkehrs, das Fahrzeug, den Fahrwegoberbau und den Untergrund, enthält. Aufgrund der unendlichen Ausdehnung des Untergrundes wurde für den Rand des endlichen FE-Gebiets, die sogenannte Scaled Boundary Finite Element Methode (SBFEM) verwendet, welche ein semi-analytisches Verfahren ist und die Abstrahlungsbedingung erfüllt. Da dieses Verfahren sowohl zeitlich als auch räumlich global ist, kann es mitunter für lange Simulationszeiten sehr aufwendig sein. Deshalb wurde es mittels der Methode der reduzierten Basisfunktionen und einer Linearisierung der Beschleunigungs-Einflussmatrix modifiziert, wodurch das Berechnungsverfahren effizienter gestaltet werden konnte. Anhand von zwei analytischen Lösungen aus der Bodendynamik konnte das modifizierte Verfahren der SBFEM validiert werden. Für ein Gleis auf homogenem Untergrund wurden mit Hilfe des gekoppelten FE-SBFE-Modells verschiedene Ergebnisse am Oberbau, im Boden und für die Ausbreitung von Erschütterungen berechnet, die sehr gut mit Ergebnissen aus der Literatur übereinstimmen. Zudem konnte das numerische Modell mit einer Schwingungsmessung an einer Schwelle eines realen Fahrwegs validiert werden. Unter Anwendung des gekoppelten FE-SBFE-Modells wurde ein Fahrweg mit Brückenbauwerk untersucht, wobei eine Beurteilung und Optimierung des Übergangsbereichs unter Verkehrslast hinsichtlich des Langzeitverhaltens im Vordergrund stand. Anhand von einfachen Bewertungskriterien, die als Indikatoren für das Langzeitverhalten dienen können, wurden verschiedene konstruktive Optimierungsmaßnahmen für den Brückenübergangsbereich diskutiert, wie zum Beispiel die Gestaltung eines Hinterfüllungsbereiches oder der Einsatz elastischer Elemente (Zwischenlagen, Besohlungen, Unterschottermatten) im Fahrweg. Das entwickelte numerische Modell für die Fahrzeug-Fahrweg-Wechselwirkung lässt sich ohne großen Aufwand auf weitere Problemstellungen von Übergangsbereichen erweitern, um spezifische konstruktive Optimierungsmaßnahmen zu untersuchen. T3 - BAM Dissertationsreihe - 157 KW - Brückenübergangsbereich KW - Fahrzeug-Fahrweg-Wechselwirkung KW - Gekoppeltes FE-SBFE-Modell PY - 2017 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-395784 SN - 978-3-9818270-6-4 SN - 1613-4249 VL - 157 SP - 1 EP - 140 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-39578 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Wehrstedt, Klaus-Dieter A1 - Döring, Ingo A1 - Holtappels, Kai A1 - Krischok, Frank A1 - Michael-Schulz, Heike A1 - Oeleker, Karin A1 - von Oertzen, Alexander A1 - Pötzsch, Michael A1 - Thomalla, Nadine T1 - Empfehlungen für die Beförderung gefährlicher Güter - Handbuch über Prüfungen und Kriterien N2 - Die „Empfehlungen über die Beförderung gefährlicher Güter, Handbuch über Prüfungen und Kriterien“ ergänzen die „ Empfehlungen über die Beförderung gefährlicher Güter, Modellvorschriften“ und das „Global harmonisierte System zur Einstufung und Kennzeichnung von Chemikalien (GHS)“. Sie enthalten Kriterien, Prüfmethoden und Verfahren, die für die Klassifizierung gefährlicher Güter gemäß den Vorschriften der Teile 2 und 3 der Modellvorschriften als auch von Chemikalien, von denen physikalische Gefahren nach dem GHS ausgehen, anzuwenden sind. Das Handbuch über Prüfungen und Kriterien, ursprünglich entwickelt vom „Economic and Social Council’s Committee of Experts on the Transport of Dangerous Goods“, welches eine erste Version im Jahre 1984 annahm, wurde regelmäßig aktualisiert und berichtigt. Gegenwärtig erfolgt die Aktualisierung unter Federführung des „Committee of Experts on the Transport of Dangerous Goods and on the Globally Harmonized System of Classification and Labelling of Chemicals“ (Sachverständigenausschuss), welches das ursprüngliche Gremium 2001 ersetzte. Die sechste überarbeitete Ausgabe enthält alle Änderungen zur fünften überarbeiteten Ausgabe, die vom Ausschuss während seiner fünften und sechsten Sitzungsperiode 2010 und 2012 angenommen wurden (veröffentlicht unter den Dokumentennummern ST/SG/AC.10/11/Rev.5/Amend.1 und ST/SG/AC.10/11/Rev.5/Amend.2), die während der siebenten Sitzungsperiode 2014 angenommenen Änderungen (ST/SG/AC.10/42/Add.2) sowie das Corrigendum zur 6. Ausgabe vom Februar 2016 (ST/SG/AC.10/11/Rev.6/Corr.1). KW - Gefahrgutbeförderung KW - UN-Prüfhandbuch PY - 2017 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-393162 SN - 978-3-9817853-2-6 N1 - Diese Ausgabe ist nicht mehr gültig, ein Link auf die nachfolgende Fassung befindet sich im Feld zugeöriger Identifikator. - This edition is no longer valid, a link to the following version is in the field related identifier. SP - 1 EP - 558 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin ET - 6. AN - OPUS4-39316 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Lee, Woojin T1 - Impact of Coating and Drying on Electrochemical Properties of Core-Shell Carbon Materials N2 - Due to the heavy overuse of fossil energy sources since the last couple of centuries, a range of serious concerns such as depletion of fossil fuels and climate change that is driven by extensive carbon dioxide (CO2) emission has risen. Rechargeable batteries have surged as eco-friendly and sustainable energy source alternative. Lithiumion batteries (LIBs) have been the most successful rechargeable battery since their commercialization. However, owing to exhaustion and instability in price of scarce raw materials, sodium-ion batteries (SIBs) have emerged as the most attractive alternative to LIBs. Nonetheless, there are still burdens to overcome for SIBs to achieve competitiveness over LIBs, particularly in improving their energy density. To address the burdens, diverse materials have been studied to date. Yet, progress and development on achieving high performance negative electrode for SIBs still remain as a key object. Hard carbon (HC) has been considered as attractive candidate, because of its high capacity and low production cost. Despite the attractiveness, inherent limitations of HCs such as excessive formation of solid-electrolyte interphase (SEI) and large irreversible capacity loss have hindered their applications. To confront this challenge, core-shell concept has been suggested by the team of Division 3.6 at BAM. The concept is to create carbon coating (shell structure) around the core material in order to mitigate formation of excessive SEI and enhance performance of the negative electrode. Shu-Han Wu and Paul Alexander Appel from Division 3.6 at BAM have synthesized various core-shell materials and have observed promising results. They made great progress in the research of core-shell materials, for example improving initial coulombic efficiency from 31% to 68%. However, there are still room for improvement. The task of this bachelor thesis work is to enhance the electrochemical performance of the core-shell materials and to investigate a more effective carbon coating method on the core material by exploring various coating parameters and different drying procedures. In this bachelor thesis, Shu-Han Wu’s synthesis precedure was repeated, ZIF-8 was pyrolyzed at 1000°C with a consequent treatment with HCl gas and washed with de� ionised water. The material (ZIF8_1000_HCl gas_H2O) was re-synthesized. Increasement in N2 Physisorption was observed after the acid treatment, consistent to Shu-Han Wu’s syntheis. The as-synthesized material was used as core material throughout this bachelor work. Moreover, 4 different core-shell carbon materials were synthesized by using chemical vapor deposition (CVD) and ball milling as synthesis methods. was used as core material and toluene was used as carbon precursor for CVD. CVD displayed an effective formation of shell structure evidenced by steep reduction in specific surface area (SSABET) from N2 physisorption characterization. Ball milling revealed to cause defects in shell structure, which was noticeable on increase in SSABET (from 14 to 379 m2 g-1) and pore size distribution characterization. Drying of powder material prior to CVD process did not exhibit a difference in porosity on the final product after CVD. From the galvanostatic cycling tests at a current density of 20 IVmA g⁻¹, it was evident that formation of shell structure enhances the performance of the material. Among the synthesized core-shell materials, the material double 1.5 h CVD with no ball milling in between exhibited the most excellent performance (ICE 60.1%). Powder drying prior to CVD showed a positive influence on improving the electrochemical performance (ICE improved from 45.1% to 51.9%). Increasing drying temperature of electrode resulted in increasements of performance, where the peak performance was reached at drying at 200°C (ICE 57.7%). The investigations of impacts of coating and drying on electrochemical properties of core-shell carbon materials would provide basis and motivation for further development of advanced negative electrode materials for SIBs. KW - Sodium-ion batteries KW - Hard carbon KW - Core-shell materials PY - 2025 SP - 1 EP - 39 CY - TU Berlin AN - OPUS4-65130 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor ED - Rogge, Andreas ED - Meng, Birgit T1 - Dauerhaftigkeit von Betonen auf Basis klimafreundlicher Bindemittel N2 - Aus Gründen des Klimaschutzes werden in den kommenden Jahren mehr Zemente mit verringertem Klinkerfaktor und alternative Bindemittel (klimafreundliche Bindemittel) zum Einsatz kommen. Für ihre sichere und zuverlässige Verwendung ist ein umfangreiches Verständnis der Einflüsse auf die Dauerhaftigkeit der aus ihnen hergestellten Betone notwendig. Der vorliegende Beitrag gibt einen kurzen Überblick über einige jüngere Entwicklungen und Forschungsergebnisse auf dem Gebiet. Der Fokus liegt auf Ergebnissen der Arbeiten von Technischen Komitees der RILEM sowie der EFC und eigenen Forschungsergebnissen. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Klimafreundliche Bindemittel KW - Betone PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-612872 SN - 978-3-9818564-7-7 SP - 22 EP - 29 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61287 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sittner, Jonathan A1 - Hoffmann, T. A1 - Bertmer, M. A1 - Neubert, M. A1 - Schuster, T. A1 - Gluth, Gregor ED - Rogge, Andreas ED - Meng, Birgit T1 - Optimizing calcination methods towards a more sustainable production of calcined clays N2 - Calcined clays are emerging as sustainable alternatives for cement production due to their potential to reduce carbon footprint and energy consumption. This study investigates the calcination of low-grade kaolinitic clays, using rotary kiln and fluidized bed. The calcined clays from the rotary kiln showed enhanced performance in the cement paste. The fluidized bed method demonstrated the potential for significant energy savings, achieving near-complete dehydroxylation with just 30 minutes of calcination. These findings highlight the promise of fluidized bed calcination for efficient clay activation, though further optimization is needed. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Calcination methods KW - Optimizing KW - Blended cement pastes KW - XRD results KW - Thermogravimetric analysis (TGA) PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-612891 SN - 978-3-9818564-7-7 SP - 37 EP - 45 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61289 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor ED - Rogge, Andreas ED - Meng, Birgit T1 - Alkalisch aktivierte Bindemittel mit hohem Säurewiderstand für die Kanalsanierung N2 - Die biogene Schwefelsäurekorrosion (BSK) von Betonbauteilen in Abwassersystemen verursacht weltweit hohen Reparaturbedarf. Um zukünftigen Reparaturbedarf zu minimieren, werden für Neubau- und Sanierungsmaßnahmen z. T. Materialien mit besonders hohem Widerstand gegen BSK benötigt. Der vorliegende Beitrag beschreibt Forschungen zu alkalisch aktivierten Bindemitteln, die bei geeigneter Formulierung einen hohen Widerstand gegen BSK bzw. Säureangriff aufweisen. Zusätzlich werden jüngste Fortschritte bei der Bewertung von Methoden zur Prüfung des Widerstands gegen BSK dargestellt. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Säurewiderstand KW - Betonbauteile KW - Abwassersystemen PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-613141 SN - 978-3-9818564-7-7 SP - 90 EP - 93 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61314 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Nikoonasab, Ali A1 - Müller, Thoralf A1 - Licht, M. A1 - Raupach, M. A1 - Gluth, Gregor ED - Rogge, Andreas ED - Meng, Birgit T1 - Sulfides in the pore solutions of GGBFS-containing concretes - Influence on the corrosion of reinforcing steel N2 - Steel corrosion in sulfide-containing solutions is a challenge in various environments, such as reinforced concrete structures. In concrete, sulfides are introduced by ground granulated blast-furnace slag (GGBFS), used in standard cements and alkali-activated materials (AAMs), affecting steel corrosion. This study examined steel in synthetic GGBFS-containing cement pore solutions using electrochemical techniques. Compared to Portland cement solutions, steel in sulfide-containing solutions exhibits lower open circuit potentials and polarisation resistances. Thus, Portland cement concrete corrosion assessment standards are unsuitable for GGBFScontaining concrete. T2 - 11. Jahrestagung des DAfStb mit 63. Forschungskolloquium der BAM Green Intelligent Building CY - Berlin, Germany DA - 16.10.2024 KW - Corrosion KW - Reinforcing steel PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-612963 SN - 978-3-9818564-7-7 SP - 55 EP - 59 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-61296 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN T1 - BAM Inside #9/2025 N2 - Interner E-Mail-Newsletter der BAM. N2 - BAM's internal email newsletter. PY - 2025 N1 - Der BAM Inside Newsletter bündelt die aktuellen Informationen der BAM. Da Informationen ggf. nur für einen definierten Zeitraum relevant sind, werden einige Links nach gewisser Zeit nicht mehr verfügbar sein. Bitte haben Sie Verständnis, dass nicht alle Links permanent vorgehalten werden können. N1 - The BAM Inside newsletter brings together the latest information from BAM. Since information may only be relevant for a specific period of time, some links will no longer be available after a while. Please understand that not all links can be maintained permanently. IS - 09/2025 SP - 1 EP - 8 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-65241 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Sobol, Oded T1 - Hydrogen assisted cracking and transport studied by ToF-SIMS and data fusion with HR-SEM N2 - For almost 150 years it is known that hydrogen has a deleterious effect on the mechanical properties of metallic components. Nowadays, the problem of hydrogen assisted degradation is highly relevant in energy related fields due to the massive use of steel as a structural component in these applications and its sensitivity to hydrogen. Since the discovery of hydrogen assisted cracking (HAC), researchers studied intensively and suggested possible explanations and mechanisms in order to define how hydrogen is affecting the material. In general, it is considered that hydrogen changes the mechanical properties more in terms of ductility (deformation capacities) than in strength (load capacities). Hydrogen concentration is one of three crucial factors in the degradation process, together with the microstructure of the material and the internal/external mechanical load. The relatively high concentration of hydrogen resulting in this loss of ductility can originate during production or before service (e.g. welding processes) and during service (i.e. catholically protected systems to eliminate corrosion processes in sour environments). In parallel to the theoretical work, tremendous efforts were, and are still, invested in searching for a proper method to elucidate, map and quantify the hydrogen in the microstructure, which is the basis for this work. For steels, the focus is mainly on the observations of diffusion processes and the interaction of hydrogen with the microstructure in regions with high local stresses/strains (for example around evolving cracks). The challenge for reaching this goal arises from the fact that accurate indication of hydrogen by means of position, unlike heavier atoms, can be made only by mass spectrometry or by interaction with another element (e.g. silver decoration, special coating and resonant nuclear reaction by nitrogen). In addition to this, the difficulty recording the hydrogen behavior while it rapidly diffuses through the material, leaving only the unpredicted failure, should be taken into account. Although using powerful characterization methods, models and computational simulations, the key to defining the mechanisms behind HAC is still under debate and not fully understood. The relationship between material and hydrogen is determined by three factors, i.e., the material structure and microstructure – determining the physical properties, the mechanical load applied on the material and the hydrogen concentration. It is well known that in order to have a complete definition of HAC these three factors must be examined locally with the minimal scale and the maximal resolution reachable. The major gap is the lack in such a characterization method or a technique by which one has the ability to detect and observe the hydrogen in the metallic microstructure. The commonly used techniques nowadays are capable of characterization of the microstructure without the ability to observe the hydrogen distribution. Global hydrogen concentration and localized hydrogen observation are possible by some techniques which are incapable of indicating a change in the structure or microstructure therefore a comprehensive overview can be gained only by combining several methods. In the presented research, secondary ion mass spectrometry (SIMS) was adopted as the main tool to detect and locally map the hydrogen distribution in two types of duplex stainless steel grades: EN 1.4462 (standard 2205 duplex stainless steel) and EN 1.4162 (2101 lean duplex stainless steel). The term duplex stainless steel (DSS) refers to the austenitic-ferritic microstructure of the steel where the combination of physical and mechanical properties of the two phases is achieved. The DSS was selected as a case study for this work due to the wide use of this grade in many energy and the lack of knowledge on hydrogen behavior in two-phase containing microstructures. ToFSIMS was exploited in-situ and ex-situ in three experimental approaches during or following an electrochemical charging procedure. This type of hydrogen charging was selected as it simulated a procedure of cathodic protection of most sub-water oil and gas extraction and delivery systems. The experimental procedures were: 1. Ex-situ charging followed by ToF-SIMS imaging for basic understanding of hydrogen distribution. 2. Ex-situ charging followed by in-situ mechanical loading to obtain information on hydrogen behavior around a propagating crack. 3. In-situ permeation of hydrogen through a steel membrane inside the ToF-SIMS to obtain information on diffusion behavior of hydrogen in a two-phase microstructure. The comprehensive view of the effect of hydrogen on steel was gained by using supplementary methods, such as high resolution scanning electron microscopy (HR-SEM), focused ion beam (FIB) and electron back-scattered diffraction (EBSD). The state of the art in this work lies in applying both: in-situ experimental approaches and data treatment of the ToF-SIMS raw data. The data treatment includes the combination of data from several sources (data fusion). The results for the ex-situ charging followed by static sample imaging and data fusion showed that when the analyzed surface is directly exposed to the electrolyte the degradation is pronounced differently in the ferrite, austenite and interface. The degradation mechanisms in the ferrite and austenite were reflected by the formation of cracks on the surface of both, where a high concentration of hydrogen was obtained. This result supports the assumption that hydrogen is attracted to highly deformed regions. The advantage of using in-situ charging/permeation in comparison to ex-situ charging is that the effect of hydrogen on the ferrite and austenite phases when the hydrogen is evolving from within the microstructure is realized, in comparison to when the analyzed surface is initially exposed directly to the electrolyte. In both experiments the ferrite was observed as a fast diffusion path for the hydrogen. The faster diffusion of hydrogen through the ferrite is expected due to the higher diffusion coefficient, however, a direct proof for the diffusion sequence in this scale was never shown. Most significant results were achieved by the ‘core’ experiments of this research. These experiments included the design of a novel dynamic mechanical loading device to apply an external load during SIMS imaging of a hydrogen precharged-notched sample. For the first time it was shown that plastic deformation induced by applying a mechanical load is resulting in a redistribution of hydrogen locally around the notch. T3 - BAM Dissertationsreihe - 160 KW - Duplex stainless steels KW - Hydrogen assisted cracking KW - Time-of-Flight secondary ion mass spectrometry KW - Data fusion PY - 2018 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-447331 SN - 1613-4249 VL - 160 SP - I EP - 180 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-44733 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Seeger, Dirk M. T1 - Wasserstoffaufnahme und -diffusion in Schweißnahtgefügen hochfester Stähle N2 - Die im Rahmen dieser Arbeit vornehmlich untersuchten supermartensitischen Stähle werden im Offshore-Bereich als geschweißte Flowlines eingesetzt. Diese Stähle sollen nach dem Prinzip „Fitness for Purpose“ bisher verwendete höher legierte Werkstoffe ersetzen. Die neuen Stähle sind aufgrund ihrer Korrosionsbeständigkeit und Festigkeit sehr gut für das beabsichtigte Einsatzgebiet geeignet. Im Sour Service besteht jedoch die Gefahr der Wasserstoffaufnahme mit nachfolgender Rissbildung. Zur Beurteilung der Risssicherheit der Schweißverbindungen sowie des unbeeinflussten Werkstoffes im Anlieferungszustand werden Wasserstofftransportdaten benötigt. Diese werden im Rahmen dieser Arbeit mittels Permeationsexperimenten an Stahlmembranen unter realistischen Einsatzbedingungen quantifiziert, so dass die Ergebnisse in computergestützte Lebensdauerberechnungen Eingang finden können. Die Untersuchungen zeigten, dass der Diffusionskoeffizient des jeweiligen Werkstoffs bzw. Gefüges nicht von der chemischen Zusammensetzung der Prüflösung abhängt. Die Subsurface-Konzentration, das ist die in die Werkstoffe eintretende Wasserstoff- konzentration, hängt dagegen vom pH-Wert, von der Schwefelwasserstoffsättigung und von der Zusammensetzung der Prüflösung ab. Die Abhängigkeit der Subsurface-Konzentration von der chemischen Zusammensetzung der Prüflösung wird zudem entscheidend durch die Chloridionenkonzentration bestimmt. Darüber hinaus wurde festgestellt, dass die chemische Zusammensetzung supermartensitischer Stähle das Permeationsverhalten erheblich beeinflusst. Beim Vergleich des Permeationsverhaltens von wärmebehandelten Proben mit Proben realer Schweißnahtgefüge ergaben sich Differenzen in Höhe einer Größenordnung. Das bedeutet letztlich, dass das Permeationsverhalten von Wasserstoff in solchen Schweiß- verbindungen für jeden Fall, abhängig von der chemischen Zusammensetzung und Temperaturführung, separat zu untersuchen ist. Zusätzlich wurde die Wasserstoffdiffusion und -aufnahme in Schweißnahtgefügen höchstfester Feinkornbaustähle untersucht. Die Ergebnisse zeigten, dass diese Werkstoffe schon bei geringfügig abgesenkten pH-Werten, wie sie in Spalten oder Rissen aufgrund von Hydrolyse vorherrschen können, Wasserstoff aufnahmen. Die Subsurface-Konzentration war wiederum von der chemischen Zusammensetzung der Prüfelektrolytlösung abhängig. Generell waren die Diffusionskoeffizienten und die Subsurface-Konzentrationen stark vom Gefüge abhängig. Der Vergleich der Resultate der höchstfesten Feinkornbaustähle S 1100 und S 890 zeigte, dass die Wasserstoffpermeation bei diesen Werkstofftypen weniger große Unterschiede aufwies als bei den supermartensitischen Stählen. N2 - The mainly investigated supermartensitic stainless steels are experiencing first applications in the offshore technology as welded flowlines. These materials are intended to replace higher alloyed steels following the principle „Fitness for Purpose“. These new types of steels are very suitable for those applications, because of their corrosion resistance and of their strength. But specially for the use under sour service conditions there exists the risk of hydrogen uptake with subsequent cracking. To evaluate the cracking resistance of the welds as well as of the unaffected material in the as-delivered condition, it is necessary to determine hydrogen transport data. Within the scope of this research project, such data are quantified in permeation experiments carried out on steel membranes under realistic application conditions. This procedure allows it to use the results in computer-assisted lifetime calculations. It was found that the diffusion coefficients of the respective materials and structures do not depend on the chemical composition of the electrolytic solution. By contrast, the subsurface concentration, i. e. the hydrogen concentration infiltrating into materials, depends on the pH value, on the H2S-saturation and on the composition of the electrolytic solution. The concentration of chloride ions was found to be the strongest factor of influence for the dependence of the subsurface concentration on the chemical composition of the electrolytic solution. In addition, a major influence of the chemical composition of supermartensitic steels on the permeation behavior has been established. The comparison of the permeation behaviour between heat treated specimens and specimens with realistic weld microstructure revealed that especially the diffusion coefficients of the heat treated specimens increased by about ten times. This means that the hydrogen permeation behaviour in such joints must be determined separately in each individual case depending on chemical composition and on the heat control. Additionally, the hydrogen diffusion and uptake in welded microstructures of ultra-high strength fine-grained structural steels was examined. The respective results showed that hydrogen uptake took place by a slight decrease of the pH value. Such decrease could be caused by hydrolysis, e. g. in crevices. The subsurface concentration was also dependent on the chemical composition of the electrolyte. A generally strong dependency of the diffusion coefficient and the subsurface concentration on the microstructure was found. A comparison of the results of both investigated steels S 1100 and S 890 showed that the hydrogen permeation in these materials does not differ as much as in the supermartensitic stainless steels. T3 - BAM Dissertationsreihe - 5 KW - Wasserstoffaufnahme und -diffusion KW - Schweißnahtgefügen hochfester Stähle PY - 2005 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1535 SN - 978-3-86509-271-3 SN - 1613-4249 VL - 5 SP - 1 EP - 144 PB - Wirtschaftsverlag NW CY - Bremerhaven AN - OPUS4-153 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Müller, A. A1 - Weimann, Karin T1 - Leistungsfähigkeit der Setztechnik KW - Aufbereitungstechnik KW - Setztechnik KW - Baustoffe KW - Recycling KW - Beton KW - Gips PY - 2010 SN - 0934-683X SN - 0178-1510 VL - 26 IS - 2 SP - 20 EP - 27 PB - Giesel-Verl. CY - Isernhagen AN - OPUS4-22946 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weimann, Karin T1 - Abbruchmethoden vor dem Hintergrund der Ersatzbaustoffverordnung N2 - Beim Abbruch von Gebäuden wird eine Vielzahl von unterschiedlichen Techniken eingesetzt. Der mit Abstand größte Teil der Abbrucharbeiten wird dabei mit mechanischen Verfahren ausgeführt. In Abhängigkeit vom rückzubauenden Gebäude können aber auch hydrodynamische Verfahren (z. B. Hochdruckwasserstrahlen), thermische Verfahren (z. B. Schneidbrennen) oder chemische Verfahren (z. B. Sprengen) angewandt werden. T2 - BGRB-Kongress - Ressourcenschonung durch Baustoff-Recycling CY - Königswinter/Bonn, Deutschland DA - 13.09.2011 KW - Bauschutt KW - Ersatzbaustoffverordnung PY - 2011 SP - 23 EP - 26 AN - OPUS4-24508 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gluth, Gregor A1 - Vogler, Nico A1 - Gardei, André A1 - Kühne, Hans-Carsten ED - Rogge, A. ED - Meng, B. T1 - Laserbasiertes Messverfahren zur Rautiefe-Bestimmung T2 - 52. DAfStb-Forschungskolloquium CY - Berlin, Deutschland DA - 2011-11-07 KW - Rauheit KW - Rautiefe KW - Volumetrische Methode KW - Sandflächenverfahren KW - Laserverfahren KW - Linienlaser PY - 2011 SN - 978-3-9814281-0-0 SP - 256 EP - 261 PB - BAM Bundesanstalt für Materialforschung und -prüfung CY - Berlin AN - OPUS4-25176 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Viyanit, Ekkarut T1 - Numerical Simulation of Hydrogen Assisted Cracking in Supermartensitic Stainless Steel Welds N2 - Replacement of expensive duplex stainless steel and conventional carbon steel by a new generation of supermartensitic stainless steel has been taken into account since the last decade corresponding to the "Fitness for Purpose" concept in order to meet the technical- economical challenge for transportation flowlines of unprocessed oil and gas products in offshore technology, in particular. Supermartensitic stainless steels can provide appropriate material properties such as: improved strength-to-weight ratio, enhanced useful corrosion resistance as well as application at relatively low cost. With decreased carbon content and increased molybdenum content compared to traditional martensitic stainless steel, hydrogen assisted stress corrosion cracking (HASCC) problems have been found during service caused by hydrogen being taken up during from sour service environments by cathodic protection. Hydrogen assisted cold cracking in supermartensitic stainless steel can also occur during fabrication welding with hydrogen picked up during welding, since this steel is relatively crack-susceptible by hydrogen. Therefore, effects of hydrogen assisted cracking (HAC), i.e. HASCC and HACC, on characteristic susceptibility of girth welds of supermartensitic stainless steel pipelines are studied in the present thesis by numerical modelling, which is developed using a available commercial finite element program. Firstly, numerical modelling for simulation of HASCC based on the NACE-TM 0177-96 approach is carried out for providing a basic understanding of the crack propagation behaviour. Secondly, a two dimensional finite element according to the gauge length cross-section of the orbitally welded pipeline is created for numerical modelling in order to calculate the time to failure of welded the component exposed to the NACE electrolyte solution with various H2S saturation. Externally applied loads of a series of constant strain rates and of the load history of full scale testing are also taken into account. Finally, numerical modelling is carried out under three specific aspects, i.e. thermal analysis, structural analysis, and hydrogen diffusion analysis, in order to simulate HACC in supermartensitic stainless steel pipelines welded orbitally by four layers of matching filler wires with an interpass temperature of 40°C. T3 - BAM Dissertationsreihe - 4 KW - numerical modelling KW - supermartensitic stainless steel KW - girth welds KW - pipeline KW - hydrogen assisted cracking (HAC) KW - hydrogen assisted stress corrosion cracking (HASCC), KW - hydrogen subsurface concentration KW - full scale test KW - post weld heat treatment (PWHT) KW - hydrogen diffusion coefficient PY - 2005 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1542 SN - 978-3-86509-270-5 SN - 1613-4249 VL - 4 SP - 1 EP - 228 PB - Wirtschaftsverlag NW CY - Bremerhaven AN - OPUS4-154 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Mente, Tobias T1 - Numerische Simulation der wasserstoffunterstützten Rissbildung in austenitisch-ferritischen Duplexstählen N2 - In der Offshore-Industrie werden seit langer Zeit austenitisch-ferritische Duplexstähle eingesetzt, da sie im Vergleich zu herkömmlichen austenitischen hochlegierten Stählen bessere Festigkeitseigenschaften aufweisen und gegenüber rein ferritischen hochlegierten Stählen eine bessere Verformbarkeit bei gleichzeitig verbesserter Korrosionsbeständigkeit, auch in aggressiver Umgebung, bieten. Dennoch zeigt das Schrifttum, dass es trotz dieser guten Eigenschaften zum Versagen von Bauteilen kommen kann, bei dem Wasserstoff für die Schadensursache eine entscheidende Rolle spielt. Zur Klärung der Schädigungsmechanismen unter Einfluss von Wasserstoff kann die numerische Simulation einen entscheidenden Beitrag leisten, da sich experimentelle Ergebnisse besser deuten und zwischen Labortests bis hin zu Bauteilversuchen übertragen lassen. Bisher wurden jedoch meistens makroskopische numerische Betrachtungen zur wasserstoffunterstützten Werkstoffschädigung in Duplexstählen durchgeführt. Die Duplexstähle bestehen jedoch nahezu aus gleichen Teilen an austenitischer und ferritischer Phase, welche unterschiedliche mechanische Eigenschaften als auch Transporteigenschaften für Wasserstoff aufweisen. Zugleich bedingt dies eine unterschiedliche Empfindlichkeit für eine wasserstoffunterstützte Werkstoffschädigung. Daher bestand die Aufgabe dieser Arbeit in der Erstellung eines numerischen Mesomodells eines realen Duplexgefüges, mit dem die Abbildung des Wasserstofftransportverhaltens, der mechanischen Spannungen und Dehnungen sowie der Rissinitiierung und des Rissfortschrittes in den einzelnen Phasen möglich ist. Zudem werden moderne Röntgenbeugungsexperimente genutzt, um den Einfluss von Wasserstoff auf die phasenspezifischen mechanischen Eigenschaften zu bestimmen. Für den Transport von Wasserstoff konnte eine deutliche Abhängigkeit von der Orientierung der austenitischen und ferritischen Phase im Gefüge gezeigt werden, wobei der Wasserstofftransport vornehmlich über die ferritische Phase erfolgt und der Wasserstoff im Austenit stärker getrappt wird. Die numerische Analyse der mechanischen Spannungen und Dehnungen in den Phasen des Duplexstahls zeigte, dass bei einer makroskopisch elastischen Beanspruchung des Duplexgefüges bereits lokal in den Phasen plastische Verformungen auftreten können. Damit verbunden ist ein erhöhtes Risiko für eine wasserstoffunterstützte Werkstoffschädigung bereits im makroskopisch elastischen Bereich, wenn ausreichend hohe Wasserstoffkonzentrationen im Duplexgefüge vorliegen. Die Ergebnisse der numerischen Simulation entsprechen den experimentellen Beobachtungen zum Wasserstofftransport und den lokalen Beanspruchungen in realen Duplexgefügen. Das Modell erlaubt somit die Identifikation risskritischer Bereiche und kritischer Kombinationen von Wasserstoffkonzentration und lokaler Beanspruchung im Duplexgefüge. Die Ergebnisse der simulierten wasserstoffunterstützten Werkstofftrennung stimmen mit experimentellen Beobachtungen zugehöriger Bruchtopographien überein. Insgesamt wird erstmalig eine numerische Simulation der wasserstoffunterstützten Werkstoffschädigung im Duplexstahl, unter Berücksichtigung der lokalen Beanspruchung und Wasserstoffverteilung in den spezifischen Phasen (Austenit / δ-Ferrit), durchgeführt. Die Ergebnisse korrelieren mit experimentellen Beobachtungen und erlauben somit ein besseres Verständnis für die Mechanismen der wasserstoffunterstützten Werkstoffschädigung in Duplexstählen. Die Simulationen unterstützen die Deutung experimenteller Ergebnisse und ermöglichen die Übertragbarkeit auf reale Bauteile. N2 - Duplex stainless steels have been used for a long time in the offshore industry, since they have higher strength than conventional austenitic stainless steels and they exhibit a better ductility as well as an improved corrosion resistance in harsh environments compared to ferritic stainless steels. However, despite these good properties the literature shows some failure cases of duplex stainless steels in which hydrogen plays a crucial role for the cause of the damage. Numerical simulations can give a significant contribution in clarifying the damage mechanisms. Because they help to interpret experimental results as well as help to transfer results from laboratory tests to component tests and vice versa. So far, most numerical simulations of hydrogen-assisted material damage in duplex stainless steels were performed at the macroscopic scale. However, duplex stainless steels consist of approximately equal portions of austenite and δ-ferrite. Both phases have different mechanical properties as well as hydrogen transport properties. Thus, the sensitivity for hydrogen-assisted damage is different in both phases, too. Therefore, the objective of this research was to develop a numerical model of a duplex stainless steel microstructure enabling simulation of hydrogen transport, mechanical stresses and strains as well as crack initiation and propagation in both phases. Additionally, modern x-ray diffraction experiments were used in order to evaluate the influence of hydrogen on the phase specific mechanical properties. For the numerical simulation of the hydrogen transport it was shown, that hydrogen Diffusion strongly depends on the alignment of austenite and δ-ferrite in the Duplex stainless steel microstructure. Also, it was proven that the hydrogen transport is mainly realized by the ferritic phase and hydrogen is trapped in the austenitic phase. The numerical analysis of phase specific mechanical stresses and strains revealed that if the duplex stainless steel is macroscopically loaded in the elastic range local plastic deformation occurs in both Austenite and δ-ferrite phase. Thus, there will be an increasing risk for hydrogen-assisted damage already in the macroscopic elastic range, if sufficiently high hydrogen concentrations are present in the microstructure. The results of the numerical simulations correlate well with experimental observations of the hydrogen transport and local stresses and strains in the duplex stainless steel microstructure. Therefore, the model allows identification of crack critical areas as well as crack critical combinations of local hydrogen concentration and local phase specific mechanical load. The results of the numerical fracture analyses agrees well with experimental observations on hydrogen-assisted cracking in duplex stainless steel with corresponding fracture topographies. Altogether, hydrogen-assisted material damage at the mesoscale level was simulated for the first time taking into account the local stresses and strains as well as the hydrogen distribution in the specific phases (austenite / δ-ferrite) of the duplex stainless steels. The results correlate well with experimental observations and thus allow a better insight in the mechanism of hydrogen-assisted material damage. The numerical simulations support the interpretation of experimental results and allow transferring results of laboratory tests to real components. T3 - BAM Dissertationsreihe - 129 KW - Duplexstahl KW - Numerische Simulation KW - Finite-Elemente-Methode KW - wasserstoffunterstützte Rissbildung PY - 2015 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-5006 SN - 978-3-9816668-9-2 VL - 129 SP - 1 EP - 225 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-500 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Wolf, Martin T1 - Zur Phänomenologie der Heißrissbildung beim Schweißen und Entwicklung aussagekräftiger Prüfverfahren N2 - Zur Ermittlung der Heißrissresistenz beim Schweißen metallischer Werkstoffe können Heißrisstests eingesetzt werden. Obwohl bislang zahlreiche Heißrisstestverfahren entwickelt wurden, kann eine unerwartete Heißrissbildung während der Durchführung von Bauteilschweißungen oftmals nicht verhindert werden. Dies ist einerseits darauf zurückzuführen, dass sich die Bedingungen im Heißrisstest von den thermomechanischen Beanspruchungen einer Bauteilschweißung zu sehr unterscheiden. Andererseits erfolgt die Auswertung der meisten Heißrissversuche mit Hilfe empirischer Parameter, mit denen die eigentlichen Mechanismen der Heißrissentstehung jedoch nur unzureichend quantifiziert werden können. Ein wesentliches Ziel war es daher, aussagekräftige Methoden zur Quantifizierung des Heißrissverhaltens beim Schweißen zu entwickeln und damit einen Beitrag zur Erhöhung der Heißrisssicherheit geschweißter Bauteile zu leisten. N2 - For determining the hot cracking resistance of materials during welding of metallic materials it is possible to employ hot cracking tests. Despite numerous hot cracking tests have been developed till now, unexpected hot cracking during welding cannot always be avoided. This is on the one hand ascribed to the fact that the conditions prevalent in hot cracking testing differ too strongly from the thermomechanical loads imposed during component welding. On the other hand, evaluation of most hot cracking tests is carried out using empiric parameters which, however, fall short of adequate quantification of the actual hot cracking mechanism. A key aim of this study was therefore to develop convincing methods for quantifying the hot cracking behaviour during welding, and thus to make a contribution towards improving the hot cracking resistance of welded components. As a prerequisite, the Modified Varestraint Transvarestraint-Test (MVT-Test) was first upgraded with a view to varying the specimen loading rate over a very wide range up to quasi-instantaneous loading. As test material, Alloy 602 CA was chosen which exhibits a pronounced dependence of hot cracking resistance on the respective shielding gas. With the use of Ar 4.8 and Ar + 1% N2 as shielding gases, hot crack-critical as well as hot crack-uncritical material behaviour could be investigated. For further elucidation of the solidification cracking mechanism, a combined model was first developed which can be used to demonstrate that the solidification crack-critical limiting temperature TER and the solidification crack-critical strain rate (dε/dt)krit are largely independent of each other and must be determined using various test concepts. Numerical temperature calculations with first implementation of the reproduced real weld pool geometries helped to determine the solidification crack-critical limiting temperature for Alloy 602 CA as a function of different welding parameters and of the investigated shielding gases. It is demonstrated that the solidification crack-critical limiting temperature rises significantly with the use of Ar + 1% N2. In addition to this, the solidification crack-critical limiting temperature is significantly dependent on the applied welding parameters. The MVTTest was also used to conduct experiments with variable specimen loading rate in both the Varestraint and the Transvarestraint mode. Various hot cracking parameters determined in these experiments were evaluated quantitatively. With regard to exclusively qualitative determination of the hot cracking resistance of materials it was found that the measurable differences are more distinct in the Varestraint mode than in the Transvarestraint mode. For hot cracking test transferability investigations, the very critical specimen loading rates at which solidification cracking does not occur yet, were experimentally determined in MVTTests. Using the obtained results in conjunction with thermomechanical simulations, the local critical strain rates in the immediate vicinity of the weld pool were calculated. It is shown that the local critical strains and strain rates constitute a crack criterion for the transferability to the newly developed Controlled Tensile Weldability Test (CTW-Test). Keywords: Solidification cracking, liquation cracking, global strain, local strain, transferability, Modified Varestraint Transvarestraint Test, weld pool geometry, hot cracking parameter, Controlled Tensile Weldability Test, Alloy 602 CA. T3 - BAM Dissertationsreihe - 19 KW - Phänomenologie Heißrissbildung KW - Schweißen und Entwicklung aussagekräftiger Prüfverfahren PY - 2006 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-1395 SN - 978-3-86509-599-2 SN - 1613-4249 VL - 19 SP - 1 EP - 218 PB - Wirtschaftsverlag NW CY - Bremerhaven AN - OPUS4-139 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -