TY - CONF A1 - Prager, Jens A1 - Bulling, Jannis T1 - Bestimmung der Rissgeometrie bei der zerstörungsfreien Ultraschallprüfung mit geführten Wellen N2 - In der zerstörungsfreien Prüfung werden in zunehmendem Maße geführte Ultraschallwellen zur Lokalisation von Fehlstellen genutzt. Geführte Ultraschallwellen zeichnen sich dadurch aus, dass sie große Distanzen innerhalb des zu prüfenden Bauteiles zurücklegen können. Das Ultraschallwellenfeld setzt sich dabei aus verschieden Moden zusammen. Etablierte Prüfverfahren mit geführten Wellen ermitteln häufig nur die Position der Fehlstelle, wobei die Laufzeiten der reflektierten Signale ausgewertet wird. Modenumwandlung bleibt dabei zumeist unberücksichtigt. Die Charakterisierung der Fehlstelle, zum Beispiel hinsichtlich der Länge eines Risses, ist dagegen herausfordernd. Aussagekräftige Zusammenhänge zwischen der Dimension oder Geometrie der Fehlstelle und ihrer Interaktion mit der Ultraschallwelle zu finden, ist Teil aktueller Forschung. Insbesondere eine Betrachtung der Moden höherer Ordnung und deren Amplitudenverhältnisse kann beim Aufspüren dieser Zusammenhänge hilfreich sein. Im Beitrag werden zunächst die Zusammenhänge zwischen den beiden fundamentalen Moden in einer isotropen Platte und der Länge eines Risses untersucht. Aus den Ergebnissen wird ein inverses Verfahren motiviert. Ein Algorithmus wird vorgestellt, der die Risslänge im Modell solange variiert, bis er die modalen Zusammenhänge einer Vorgabe oder einer Messung rekonstruiert. Die eingesetzte Scaled Boundary Finite Element Method ermöglicht dabei eine sehr kurze Rechenzeit in jeden Optimierungsschritt. Zusätzlich ermöglicht die Methode eine Auswertung der modalen Zusammenhänge ohne Postprocessing, was die Rechenzeiten weiter verkürzt. T2 - DAGA 2019 CY - Rostock, Germany DA - 18.03.2019 KW - Geführte Wellen KW - Scaled Boundary Finite Element Method KW - Amplitudenverhältnisse PY - 2019 AN - OPUS4-47730 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bulling, Jannis A1 - Gravenkamp, Hauke T1 - Comparison of different models for stress singularities in higher order finite element methods for elastic waves N2 - The Spectral Element Method (SEM) has been proven to be an efficient numerical method for solving the wave equation in linear elastic bodies. This efficiency is reduced if a stress singularity is present in the body. For example, re-entrant corners, material interfaces, fixed boundaries, and especially crack tips can cause stress singularities. To preserve the efficiency of the SEM, special solution strategies are required. There are many approaches which consider stress singularities, but comparisons are rare for dynamic problems. Finding an efficient model is an important step for many applications. In particular, applications for structural health monitoring and non-destructive evaluation rely on accurate and efficient crack models. In this contribution, we present several models to capture singularities in combination with the SEM. The theory behind the models are shortly summarized and we show results for different benchmark problems in two dimensions. The first model deploys a new class of singular elements. For these singular elements, the crack tip approximation is computed based on the static Scaled Boundary Finite Element Method (SBFEM). The second model uses the continued‐fraction‐based SBFEM, while the third model uses an hp-refinement near the singularity. The models are compared among each other and evaluated in terms of their respective efficiency and accuracy. T2 - GAMM 2019 CY - Vienna, Austria DA - 18.02.2019 KW - SBFEM KW - Stress singularities KW - Higher order FEM PY - 2019 AN - OPUS4-47753 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Beckmann, Jörg A1 - Bär, Sylke A1 - Spranger, Holger T1 - Synthetische Aperturfokussierung für die Terahertzspektroskopie N2 - Die zeitaufgelöste THz-Spektroskopie (THz-TDS) operiert mit elektromagnetischen Impulsen, die ein Amplitudenspektrum im unteren THz-Bereich aufweisen. Die THz-TDS ist in der Lage, dielektrische Volumina zerstörungs- und kontaktfreie zu durchstrahlen. Um eine 3D-THz Bildung zu ermöglichen, wurde für die THz-TDS ein rechnergestütztes Mess- und Rekonstruktionsverfahren (THz-TD-SAFT) entwickelt, mit dem es gelingt, unter Verwendung der im Zeitbereich registrierten THz-TDS-Daten das Volumeninnere in Form eines dreidimensionalen Tomogramms zu rekonstruieren. Die THz-TD-SAFT basiert auf die für die Ultraschalltechnik entwickelte Synthetische Apertur Fokussierung (SAFT) bzw. des heuristisch begründeten Algorithmus des Synthetischen Apertur Radars (SAR). Anhand von Beispielen wird die Möglichkeiten der THz-TD-SAFT demonstriert und nachgewiesen, dass mit dem Rekonstruktionsansatz die künstlich eingebauten Fehlstellen bezüglich der Position und Größe geometrisch richtig im Tomogramm abgebildet werden können. T2 - 4. Fachseminar, Mikrowellen- und Terahertz-Prüftechnik in der Praxis CY - Fürth, Germany DA - 02.04.2019 KW - Zeitaufgelöste THz-Spektroskopie KW - THz-TD-SAFT KW - THz-Tommographie PY - 2019 AN - OPUS4-47756 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Léonard, Fabien T1 - Distance transforms and correlation maps: advanced impact damage characterisation in composite panels N2 - One of the great strengths of X-ray computed tomography over conventional inspection methods (ultrasound, thermography, radiography) is that it can image damage in 3D. However for curved or deformed composite panels, it can be difficult to automatically ascribe the damage to specific plies or inter-ply interfaces. An X-ray computed tomography (CT) data processing methodology is developed to extract the through-thickness distribution of damage in curved or deformed composite panels. The method is applied to [(0°/90°)2]s carbon fibre reinforced polymer (CFRP) panels subjected low velocity impact damage (5 J up to 20 J) providing 3D ply-by-ply damage visualisation and analysis. Our distance transform approach allows slices to be taken that approximately follow the composite curvature allowing the impact damage to be separated, visualised and quantified in 3D on a ply-by-ply basis. In this way the interply delaminations have been mapped, showing characteristic peanut shaped delaminations with the major axis oriented with the fibres in the ply below the interface. This registry to the profile of the panel constitutes a significant improvement in our ability to characterise impact damage in composite laminates and extract relevant measurements from X-ray CT datasets. T2 - Dagstuhl Seminar 19151 Quantitative data visualisation challenge CY - Dagstuhl, Germany DA - 11.04.2019 KW - Computed tomography KW - X-ray computed tomography KW - Data processing PY - 2019 AN - OPUS4-47830 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mitzkus, Anja A1 - Sahre, Mario A1 - Basedau, Frank A1 - Hofman, Detlef A1 - Beck, Uwe T1 - Fiber Bragg Gratings for In-Situ Stress Monitoring of Electrochemical Deposition N2 - The in-situ monitoring of electrochemical deposition (ECD) processes is still a challenge regarding the measurement of the effective temperature of the substrate and the formation of mechanical stress in the layer under given plating conditions. Monitoring problems can be solved by applying a pre-coated fiber Bragg grating (FBG) to the electrolytic process as the shift of the Bragg wavelength is affected by both the temperature of the electrolyte near the substrate and the stress formation in the growing layer. The experimental FBG set-up and the quantitative determination of temperature- and stress-related strain is described for a nickel-iron electrolyte. KW - Fiber Bragg grating (FBG) KW - Electrochemical deposition (ECD) KW - Optical fibers PY - 2019 DO - https://doi.org/10.1149/2.0111906jes SN - 0013-4651 VL - 166 IS - 6 SP - B312 EP - B315 PB - Electrochemical Society CY - Pennington, NJ AN - OPUS4-47738 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bulling, Jannis A1 - Prager, Jens T1 - Bestimmung der Rissgeometrie bei der zerstörungsfreien Ultraschallprüfung mit geführten Wellen N2 - In der zerstörungsfreien Prüfung werden in zunehmendem Maße geführte Ultraschallwellen zur Lokalisation von Fehlstellen genutzt. Geführte Ultraschallwellen zeichnen sich dadurch aus, dass sie große Distanzen innerhalb des zu prüfenden Bauteiles zurücklegen können. Das Ultraschallwellenfeld setzt sich dabei aus verschieden Moden zusammen. Etablierte Prüfverfahren mit geführten Wellen ermitteln häufig nur die Position der Fehlstelle, wobei die Laufzeiten der reflektierten Signale ausgewertet wird. Modenumwandlung bleibt dabei zumeist unberücksichtigt. Die Charakterisierung der Fehlstelle, zum Beispiel hinsichtlich der Länge eines Risses, ist dagegen herausfordernd. Aussagekräftige Zusammenhänge zwischen der Dimension oder Geometrie der Fehlstelle und ihrer Interaktion mit der Ultraschallwelle zu finden, ist Teil aktueller Forschung. Insbesondere eine Betrachtung der Moden höherer Ordnung und deren Amplitudenverhältnisse kann beim Aufspüren dieser Zusammenhänge hilfreich sein. Im Beitrag werden zunächst die Zusammenhänge zwischen den beiden fundamentalen Moden in einer isotropen Platte und der Länge eines Risses untersucht. Aus den Ergebnissen wird ein inverses Verfahren motiviert. Ein Algorithmus wird vorgestellt, der die Risslänge im Modell solange variiert, bis er die modalen Zusammenhänge einer Vorgabe oder einer Messung rekonstruiert. Die eingesetzte Scaled Boundary Finite Element Method ermöglicht dabei eine sehr kurze Rechenzeit in jeden Optimierungsschritt. Zusätzlich ermöglicht die Methode eine Auswertung der modalen Zusammenhänge ohne Postprocessing, was die Rechenzeiten weiter verkürzt. T2 - DAGA 2019 - 45. Jahrestagung für Akustik CY - Rostock, Germany DA - 18.03.2019 KW - Geführte Ultraschallwellen KW - Zerstörungsfreien Prüfung KW - Scaled Boundary Finite Element Method PY - 2019 VL - 45 SP - 1063 PB - Deutsche Gesellschaft für Akustik e.V. AN - OPUS4-47783 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kotschate, Daniel A1 - Gaal, Mate T1 - Plasma-akustische Wechselwirkungen von Mikrohohlkathodenentladungen N2 - Während des Entladungsprozesses interagieren Mikrohohlkathodenentladungen (engl. micro hollow cathode discharges) durch verschiedenste physikalische Phänomene mit ihrer Umgebung. Analog zu Funken- und Koronaentladung treten neben den optischen Erscheinungen auch akustische Wechselwirkungen bis in den Ultraschallbereich auf. Diese Wechselwirkungen sind bisher jedoch nur selten Gegenstand der Forschung gewesen. Durch elektro-chemischen Prozesse und die Stromdichteverteilung während des Zündvorgangs erfährt das angrenzende Fluid eine, durch den thermoakustischen Effekt hervorgerufene, rapide Dichteänderung und erzeugt somit eine akustische Emission. Dieser Beitrag gibt einen Überblick über den letzten Stand der akustischen Beschreibung der Mikrohohlkathode. Weiterhin wird anhand von Anwendungsbeispielen, wie der Charakterisierung von akustischen Sensoren, sowie der Nutzung innerhalb der zerstörungsfreien Werkstoffprüfung, die Nutzung dieser Entladungsart präsentiert. Darüber hinaus erlaubt die Kenntnis hinsichtlich der akustischen Eigenschaften der Entladung wichtige Rückschlüsse im Rahmen der Plasmadiagnostik. T2 - 45. Jahrestagung für Akustik (DAGA 2019) CY - Rostock, Germany DA - 18.03.2019 KW - Micro hollow cathode discharge KW - Atmospheric pressure plasma PY - 2019 SP - 1049 EP - 1051 AN - OPUS4-47790 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Léonard, Fabien A1 - Bruno, Giovanni T1 - On nominal-actual comparisons for additive manufacturing applications N2 - Nominal-actual comparisons are routinely performed to compare a manufactured specimen to a reference specimen. X-ray Computed Tomography (CT) has brought a profound change in the way that tolerance verifications are performed in industry, by allowing the inner and outer geometries of an object to be measured, without the need for external access or destructive testing. As a results, CT is increasingly used in additive manufacturing applications, where a nominal-actual comparison performed between the digital model (CAD file), used as an input for the 3D printer, and the CT volume from the printed part, can provide invaluable information as to the accuracy of the printing process. However, the nominal-actual comparison process is somewhat different when applied to additively manufactured specimens by comparison to conventionally manufactured specimens. T2 - 9th Conference on Industrial Computed Tomography CY - Padova, Italy DA - 14.02.2019 KW - Computed tomography KW - X-ray computed tomography KW - Implants PY - 2019 AN - OPUS4-47832 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Léonard, Fabien A1 - Bruno, Giovanni T1 - On nominal-actual comparisons for additive manufacturing applications N2 - Nominal-actual comparisons are routinely performed to compare a manufactured specimen to a reference specimen. X-ray Computed Tomography (CT) has brought a profound change in the way that tolerance verifications are performed in industry, by allowing the inner and outer geometries of an object to be measured, without the need for external access or destructive testing. As a results, CT is increasingly used in additive manufacturing applications, where a nominal-actual comparison performed between the digital model (CAD file), used as an input for the 3D printer, and the CT volume from the printed part, can provide invaluable information as to the accuracy of the printing process. However, the nominal-actual comparison process is somewhat different when applied to additively manufactured specimens by comparison to conventionally manufactured specimens. T2 - 9th Conference on Industrial Computed Tomography CY - Padova, Italy DA - 14.02.2019 KW - Computed tomography KW - X-ray computed tomography PY - 2019 AN - OPUS4-47833 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Küttenbaum, Stefan A1 - Taffe, A. A1 - Braml, T. A1 - Maack, Stefan T1 - Non-Destructive Testing: A valuable source of information for reliability assessments N2 - The reassessment of bridges is becoming increasingly important. The basic requirement for analyses of structural safety is reliable knowledge about individual structures. This paper introduces the new approach to evaluate the quality of measured data gained from non-destructive testing (NDT) to provide reliable, objective, and relevant information about existing bridges. The purpose is to relate this validated knowledge to probabilistic analyses. Bridging the gap between NDT and numerical reassessments indicates reduced numerical uncertainties and residual service time extensions. This paper deals with an application of this approach using measurement data collected by ultrasonic technique at a prestressed concrete bridge. T2 - IABSE Symposium 2019 CY - Guimarães, Portugal DA - 27.03.2019 KW - NDT KW - Measurement KW - Structural safety KW - Concrete bridges KW - Eexisting structures PY - 2019 AN - OPUS4-47714 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Küttenbaum, Stefan A1 - Maack, Stefan A1 - Taffe, A. A1 - Braml, T. T1 - Non-destructive testing in civil engineering: A valuable source of information for reliability assessments N2 - The reassessment of bridges is becoming increasingly important. The basic requirement for analyses of structural safety is reliable knowledge about individual structures. This paper introduces the new approach to evaluate the quality of measured data gained from non-destructive testing (NDT) to provide reliable, objective, and relevant information about existing bridges. The purpose is to relate this validated knowledge to probabilistic analyses. Bridging the gap between NDT and numerical reassessments indicates reduced numerical uncertainties and residual service time extensions. This paper deals with an application of this approach using measurement data collected by ultrasonic technique at a prestressed concrete bridge. T2 - IABSE Symposium 2019 CY - Guimarães, Portugal DA - 27.03.2019 KW - NDT KW - Measurement KW - Structural safety KW - Uncertainty KW - Existing bridges PY - 2019 SN - 978-3-85748-163-5 VL - 112 SP - 1132 EP - 1139 PB - IABSE (International Association for Bridge and Structural Engineering) CY - Zurich, Switzerland AN - OPUS4-47815 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bühling, Benjamin A1 - Strangfeld, Christoph A1 - Maack, Stefan T1 - OsciCheck - Fluidische Erzeugung eines luftgekoppelten Ultraschallpulses N2 - Das ZIM-Projekt OsciCheck wird vorgestellt, die Funktionsweise eines fluidischen Oszillators erläutert und die nächsten Arbeitsschritte im Projekt dargestellt. T2 - Herbstworkshop der jungen DEGA CY - Berlin, Germany DA - 01.11.2019 KW - Fluidischer Oszillator KW - Ultraschall KW - Luftgekoppelter Ultraschall KW - Zerstörungsfreie Prüfung PY - 2019 AN - OPUS4-51294 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ahmadi, Samim A1 - Thiel, Erik A1 - Karagianni, Christina A1 - Hirsch, Philipp Daniel A1 - Burgholzer, P. A1 - Mayr, G. A1 - Jung, P. A1 - Caire, G. A1 - Ziegler, Mathias T1 - Photothermal super resolution image reconstruction using structured 1D laser illumination N2 - The separation of two closely spaced defects in fields of Thermographic NDE is very challenging. The diffusive nature of thermal waves leads to a fundamental limitation in spatial resolution. Therefore, super resolution image reconstruction can be used. A new concerted ansatz based on spatially structured heating and joint sparsity of the signal ensemble allows for an improved reconstruction of closely spaced defects. This new technique has been studied using a 1D laser array with randomly chosen illumination pattern. This paper presents the results after applying super resolution algorithms, such as the iterative joint sparsity (IJOSP) algorithm, to our processed measurement data. Different data processing techniques before applying the IJOSP algorithm as well as the influence of regularization parameters in the data processing techniques are discussed. Moreover, the degradation of super resolution reconstruction goodness by the choice of experimental parameters such as laser line width or number of measurements is shown. The application of the super resolution results in a spatial resolution enhancement of approximately a factor of four which leads to a better separation of two closely spaced defects. T2 - Quantitative Nondestructive Evaluation Conference 2019 CY - Portland, OR, USA DA - 14.07.2019 KW - Super resolution KW - Photothermal KW - Thermography KW - Laser PY - 2019 SP - Paper 8593, 1 PB - ASME AN - OPUS4-50924 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Alhadad, Mohamad Saddik T1 - Entwicklung und Validierung eines luftgekoppelen Impakt-Echo-Messverfahrens mittels fluidischer Anregung N2 - Die steigende Nachfrage von zerstörungsfreien Prüfverfahren, welche die Zeitinvestition verbessern und eine kontinuierliche Messung ermöglichen, erfordert die Entwicklung des luftgekoppltes Impakt-Echo-Messverfahrens. Diese Entwicklung kann durch die fluidische Anregung ermöglicht werden. Das Ziel dieser vorliegenden Arbeit war der Aufbau einer Messapparatur, die auf Schnelligkeit setzt und kontinuierlich misst. Nach der Durchführung der fluidischen Anregung wurden mit Hilfe eines Laservibrometers die Daten aufgenommen. Zur Analysierung der auf diese Weise erhobenen Messwerte wurden sie mittels der Fast-Fourier-Transformation in den Frequenzbereich transformiert. Für den Zweck der Validierung wurden Zylinder-Probekörper und Platten-Probekörper wurden verwendet. Die Messungen an den Zylinder-Probekörpern lieferten erfolgreiche Ergebnisse, während die Messungen an den Platten-Probekörpern weitere Untersuchung und Entwicklung benötigten werden. KW - Bauwesen KW - Delamination KW - Kontaktloses Impakt-Echo KW - Dickenbestimmung PY - 2019 SP - 1 EP - 87 CY - Berlin AN - OPUS4-50320 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gottlieb, C. A1 - Lierenfeld, M. B. A1 - Wilsch, Gerd A1 - Bohling, C. T1 - Es geht auch einfacher N2 - Mit laserbasiertem Verfahren Zustand von Betonbauwerken erfassen: Die Laserinduzierte Breakdown Spektroskopie (LIBS) stellt eine Alternative zur nasschemischen Analyse dar, um den Zustand von Betonbauwerken zu erfassen. Bei diesem Verfahren laufen der Analysevorgang und die Auswertung automatisiert ab. Ein Prototyp für die mobile Anwendung auf der Baustelle steht zur Verfügung. So kann auf Knopfdruck ein schriftlicher Bericht erstellt werden, der einen genauen Wert für die Eindringtiefe eines relevanten Elements wie Chlorid ausgibt. KW - Beton KW - LIBS KW - Chlorid KW - Vor-Ort-Untersuchung PY - 2019 VL - 42 IS - 7 SP - 28 EP - 31 PB - Verlagsgesellschaft Rudolf Müller GmbH CY - Köln AN - OPUS4-50283 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Maack, Stefan T1 - Ultraschall-Echoverfahren an Betonbauteilen mit geneigten Rückwänden - Entwicklung von Testkörpern N2 - Mit dem Ultraschall-Echoverfahren können geometrische Abmessungen von Betonbauteilen bestimmt werden. Es hat sich gezeigt, dass die Bauteilrückwand bei der Messung an Massivbrücken häufig nicht planparallel zur Messfläche ausgeführt ist. Es wird erwartet, dass der Einfluss einer Neigung der Rückwand gegenüber der Messfläche auf die Messunsicherheit bei der Dickenbestimmung nicht vernachlässigbar ist. In diesem Beitrag werden die fünf konzipierten Betonprobekörper und ausgewählte Messergebnisse zur Bestimmung dieses Einflusses gezeigt. T2 - DACH-Jahrestagung 2019 - Zerstörungsfreie Materialprüfung CY - Friedrichshafen, Germany DA - 27.05.2019 KW - Messunsicherheit KW - Ultraschall PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-504317 AN - OPUS4-50431 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Dietz, T. A1 - Gottlieb, Cassian A1 - Kohns, P. A1 - Ankerhold, G. T1 - Comparison of atomic and molecular emission in LIBS for the quantification of harmful species in cement-based materials N2 - Due to the penetration of harmful chlorides into concrete, e.g. from de-icing salt, damage processes such as chloride-related pitting corrosion can occur if critical values are exceeded. In this study, multiphase materials such as chloride-contaminated concrete are examined in detail. A direct comparison is made by analyzing the spectroscopic information of simultaneously measured atomic and molecular emissions with laser-induced breakdown spectroscopy (LIBS). In addition, the influence on the calibration is examined on the basis of the combined spectral information of both reaction paths of the penetrated chlorides. The calibration models of univariate and multivariate methods were validated using reference samples with wet chemical analysis. The results are applied to a concrete sample of a parking deck, which was also analyzed by potentiometric wet chemistry. In order to account for the heterogeneity of concrete, spatially (200 μm) and spectroscopically (0.1 nm) resolved LIBS measurements were performed using a fully automated laboratory system. Simultaneous measurements with three spectrometers allow the analysis of the emission processes of several elements such as Cl, Ca, O, Si and Mg as well as the newly formed molecules CaO and CaCl. The evaluation of the molecular emission in combination with atomic lines extends the analytical performance, since different concrete phases such as aggregates and cement matrix can be better represented. The measurements were carried out in ambient air and with helium purge gas. The limit of detection (LOD) achieved for a combined evaluation of atomic and molecular emission was determined to be 0.028 wt%. KW - Laser-induced breakdown spectroscopy (LIBS) KW - Cement-based materials KW - Atomic and molecular mapping KW - Chemometrics PY - 2019 DO - https://doi.org/10.1016/j.sab.2019.105707 SN - 0584-8547 VL - 161 SP - 105707 PB - Elsevier B.V. AN - OPUS4-50438 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völker, Christoph T1 - Integration von Forschungsdaten im Bereich zerstörungsfreien Prüfung (ZfP) im Bauwesen N2 - Der Vortrag gibt einen Überblick zu Fragestellungen, Herausforderungen und Nutzen von semantischer Datenintegration im Forschungsbereich der zerstörungsfreien Prüfung im Bauwesen. T2 - 1. KDA Kolloquium der BAM CY - Berlin, Germany DA - 29.03.2019 KW - Digitalisierung KW - Ontology KW - ZfP KW - Beton KW - Datenanalyse PY - 2019 AN - OPUS4-50026 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - THES A1 - Schumacher, David T1 - Zerstörungsfreie Prüfung mit photonenzählenden und spektralauflösenden Röntgenmatrixdetektoren am Beispiel von Werkstoffverbunden N2 - Diese Arbeit beschäftigt sich mit den Eigenschaften der photonenzählenden und spektralauflösenden Detektortechnik und möglichen Anwendungsgebieten in der zerstörungsfreien Prüfung. Dabei wurden konventionelle und photonenzählende Detektortechniken hinsichtlich der Bildqualität und Anwendbarkeit bei unterschiedlichen Prüfaufgaben verglichen und untersucht, inwiefern sich die Energieschwellwertsetzung auf die erreichbare Bildqualität und eine Materialdiskriminierbarkeit bei verschiedenen radiographischen Verfahren auswirkt. Anhand von Anwendungsbeispielen wurden diese Eigenschaften und deren Auswirkung auf das Messergebnis analysiert. Neben der Radiographie wurden auch dreidimensionale Verfahren wie CT und Laminographie berücksichtigt. Als eine der wichtigsten Eigenschaften der photonenzählenden Detektortechnik wurden zunächst die Energieauflösung des photonenzählenden Detektors und die Homogenität der Energieantwort über größere Detektorbereiche bestimmt. Dabei stellte sich heraus, dass die Energieauflösung eines abgegrenzten Detektorbereichs ca. 32 % bei 60 keV beträgt und die Streuung in der Energieantwort der einzelnen Detektorbereiche ca. 12 % ausmacht, woraus sich eine Gesamtunsicherheit in der spektralen Detektorantwort von ca. 44 % ergibt. Die geringe Energieauflösung und das stark heterogene Verhalten der Detektorbereiche ergeben sich vor allem aus der Detektorelektronik, welche nur eine globale Energieschwellwertsetzung zulässt. Trotz dieser Einschränkungen konnte demonstriert werden, dass auch konventionelle radiographische Verfahren, wie Radiographie oder CT, vom Einsatz der photonenzählenden Technik profitieren. So ist es mit dieser Technik möglich, bei sehr geringen Dosisleistungen (z.B. aufgrund der Durchstrahlung großer Wandstärken von dichten Materialien) noch sehr gute Bildqualitäten zu erreichen. Die hohe Dynamik und Kontrastempfindlichkeit dieser Technik begünstigen die Inspektion von Leichtbauwerkstoffen wie Faserverbunde, was anhand von Vergleichen mit herkömmlicher Detektortechnik und anderen ZfP-Verfahren gezeigt werden konnte. Daneben konnte durch den Einsatz der Energieschwellwertsetzung der Einfluss von nicht bildzeichnender Streustrahlung im Röntgenbild um bis zu 20 % reduziert werden. Die Auswirkungen von Aufhärtungseffekten in der CT konnten sogar um bis zu Faktor 1 000 (in der mittleren quadratischen Abweichung), im Vergleich zu herkömmlicher Detektortechnik, reduziert werden. Der Einsatz von photonenzählender Detektortechnik mit Röntgenblitzröhren ist hingegen nicht sinnvoll, da aufgrund der hohen Photonendichte pro Puls und einer endlichen Totzeit des Detektors in der Größenordnung der Pulsbreite eines Blitzes nur ein geringes Signal detektiert werden kann. Im Hinblick auf eine Materialdiskriminierbarkeit konnte demonstriert werden, dass im Fall einer Radiographie anhand der Energieschwellwertsetzung im Detektor eine materialstärkenunabhängige Diskriminierung zwischen zwei Materialien (hier: Al und Fe) erzielt werden kann. Unter Einsatz mehrerer Energiefenster und eines Verfahrens der explorativen und multivariaten Datenanalyse konnte eine materialaufgelöste CT eines Multi-Material-Phantoms erreicht werden, wobei die Schwächungskoeffizienten der enthaltenen Materialien im relevanten Energieberiech teilweise sehr dicht beieinander lagen. Neben Radiographie und CT wurde auch die Möglichkeit einer materialaufgelösten Laminographie am Beispiel eines glasfaserverstärkten Rotorblatts untersucht. Anhand der Energieschwellwertsetzung war nicht nur eine eindeutige Trennung der Glasfasern von der Epoxidharzmatrix möglich, sondern auch eine signifikante Reduzierung der durch die Laminographie entstandenen Artefakte. Der damit verbundene Gewinn an Information führt zu einer verbesserten Aussagefähigkeit des Untersuchungsergebnisses, was letztendlich eine gesteigerte Betriebssicherheit zur Folge hat. N2 - This thesis investigates the properties of photon counting and energy discriminating digital detector arrays and possible applications in the field of non-destructive testing. Conventional integrating detector technology was compared with photon counting technology in terms of image quality and applicability in different inspection tasks. The impact of internal energy thresholding on material discriminability and achievable image quality was investigated for different radiological methods. The properties of photon counting detectors and their impact on the measurement result were analyzed for different applications including three-dimensional methods such as CT and laminography in addition to radiographic testing. Energy resolution is one of the most important properties of photon counting technology. Therefore, energy resolution was initially determined in addition to the homogeneity of the energy Response across the detector. It was found that the energy resolution amounts to approx. 32 % for a 60 keV monoenergetic spectrum (241Am). In combination with the variance in the response of single detector tiles of approx. 12 % the total uncertainty in the detector energy response appears to approx. 44 %. This low energy resolution and strongly heterogenous detector response result mainly from the detector electronics which only allow setting global energy thresholds. Despite these limitations it was demonstrated that even conventional single energy techniques, such as radiography or CT, benefit from photon counting technology. Thus, this technology allows to gain high quality images even at very low dose rates which might occur e.g. at high wall thickness Penetration of dense materials. The high dynamic range and high contrast sensitivity facilitate the inspection of lightweight materials such as fiber composites which was shown by comparison with integrating technology and other NDT methods. Furthermore, the use of energy thresholding enables to reduce the influence of non-imaging scattered radiation within the X-ray image by about 20 %. The impact of beam hardening artefacts in CT was reduced even up to a factor of 1 000, compared to conventional integrating detector technology. In contrast, the use of photon counting technology with x-ray flash tubes is not useful, since the high photon density within a single flash and a finite dead time of the detector only yield a very low signal. In terms of material discriminability, it was shown that due to energy thresholding a thickness Independent material separation between two materials (here: Al and Fe) can be achieved in the case of a radiography. By using more than two energy windows in combination with multivariate methods of data analysis, a material resolved CT of a multi-material phantom was performed in which six materials were separated distinctly despite very close attenuation coefficients in the relevant energy range. In addition to radiography and CT, the possibility of a material resolved laminography was investigated by means of a glass fiber reinforced wind turbine blade. In addition to a distinct separation between glass fibers and resin matrix, a significant reduction of cross artefacts that inherently arise from the laminography could be achieved. This gain in information yields a higher significance of the measurement and hence an increased reliability of the component or the whole system. T3 - BAM Dissertationsreihe - 165 KW - Zerstörungsfreie Prüfung KW - Photonenzählende Detektoren KW - Radiographie KW - Laminographie KW - Computer-Tomographie KW - Dual-Energy KW - Nondestructive testing KW - Photon counting detectors KW - Radiography KW - Laminography KW - Computed tomography KW - Dual energy PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-500327 SN - 1613-4249 VL - 165 SP - 1 EP - 172 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-50032 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Al-Falahat, A.M. A1 - Kupsch, Andreas A1 - Hentschel, M.P. A1 - Lange, A. A1 - Kardjilov, N. A1 - Markötter, Henning A1 - Manke, I. T1 - Correction approach of detector backlighting in radiography N2 - In various kinds of radiography, deficient transmission imaging may occur due to backlighting inside the detector itself arising from light or radiation scattering. The related intensity mismatches barely disturb the high resolution contrast, but its long range nature results in reduced attenuation levels which are often disregarded. Based on X-ray observations and an empirical formalism, a procedure is developed for a first order correction of detector backlighting. A backlighting factor is modeled as a function of the relative detector coverage by the sample projection. Different cases of sample transmission are regarded at different backlight factors and detector coverage. The additional intensity of backlighting may strongly affect the values of materials’ attenuation up to a few 10%. The presented scenario provides a comfortable procedure for corrections of X-ray or neutron transmission imaging data. KW - X-ray imaging KW - Neutron imaging KW - Radiology KW - Backlighting KW - Digital detector array PY - 2019 DO - https://doi.org/10.1063/1.5097170 SN - 0034-6748 VL - 90 IS - 12 SP - 125108 PB - American Institute of Physics CY - Melville, NY, USA AN - OPUS4-50217 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pelkner, Matthias A1 - Ehlers, Henrik T1 - Electromagnetic testing for additive manufacturing N2 - With rising popularity and availability of additive manufacturing (AM), companies mainly in the aerospace sector, set high requirements on quality control of AM parts, especially produced with selective laser melting (SLM). Since it was shown that those parts are prawn to flaws like pores or cracks, every part needs to be tested. Therefore, NDT Methods, like eddy current testing (ET), could help to characterize SLM parts. Research on ET has shown, that offline ET with high spatial resolution MR (magneto resistive) sensor arrays is possible and that flaws as small as 50 µm could be detected while significantly reducing testing time. A first approach on automated online ET method for testing SLM parts is proposed in this contribution. T2 - IIW 2019 CY - Bratislava, Slovakia DA - 08.07.2019 KW - Additive manufacturing KW - Giant magneto resistance KW - Online monitoring KW - Eddy current testing PY - 2019 AN - OPUS4-50244 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pelkner, Matthias A1 - Ehlers, Henrik A1 - Pohl, Rainer A1 - Thewes, R. T1 - Hochauflösende Wirbelstromprüfung in der additiven Fertigung N2 - In den letzten Jahren wurden enorme Fortschritte bei der additiven Fertigung erzielt. So sind heutzutage industrielle Kleinserienfertigungen mit den 3D-Druckverfahren wirtschaftlich und konkurrenzfähig. Allerdings ist der Einsatz in Bezug auf sicherheitsrelevante Komponenten noch nicht vollumfänglich möglich. Grund hierfür sind die Materialeigenschaften 3D-gedruckter Komponenten, welche sich von den Eigenschaften konventionell gefertigter Materialien unterscheiden (Variationen im Gefüge, der Härte usw.). Ein Ansatz zur Lösung dieses Problems ist der Einsatz geeigneter online-Prüfverfahren zur Qualitätssicherung. Diese befinden sich –abgesehen von kamerabasierten Verfahren– aber noch im Entwicklungsstadium. Bei metallischen Werkstoffen stellt die Wirbelstromprüfung ein geeignetes Verfahren zur lagenweisen Online-Überprüfung des Fertigungsprozesses dar. Der Beitrag gibt einen Überblick über die derzeitige Patentlage sowie den Stand der Forschung zum Einsatz der Wirbelstromprüfung beim 3D-Druck metallischer Komponenten. Am Beispiel des pulverbasierten SLM-Verfahrens (selective laser melting; selektives Laserschmelzen) werden zudem Arbeiten der BAM und erste Ergebnisse einer angepassten Wirbelstromtechnik unter Verwendung von GMR-Sensoren (giant magneto resistance) vorgestellt. Hier wird das Ziel verfolgt, hochauflösend kleinste Fehler und Poren (im Bereich ≈100 µm) in der Oberfläche zu detektieren und durch lagenweises Abrastern einen 3D-Datensatz für die Qualitätskontrolle zu erstellen. Schließlich soll das System in der Lage sein, aktiv in den Fertigungsprozess einzugreifen, wodurch entweder die Produktion fehlerhafter Bauteile gestoppt wird oder durch geeignete Maßnahmen Fehler ausgeheilt werden. T2 - Wirbelstromprüfung – Aktuelle Anwendungen und Entwicklungen CY - Celle, Germany DA - 10.09.2019 KW - Additive Fertigung KW - Wirbelstromprüfung KW - Onlinemonitoring KW - Riesenmagnetwiderstand KW - GMR PY - 2019 AN - OPUS4-50245 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Hauke, Max T1 - Entwicklung eines Versuchsstandes zur Dickenbestimmung von Werkstoffen mithilfe von frequenzmoduliertem Ultraschall N2 - Die vorliegende Arbeit beschäftigt sich mit der Entwicklung eines Versuchsstandes zur Di-ckenbestimmung von Werkstoffen mithilfe von frequenzmoduliertem luftgekoppelten Ultra-schall. Zur Erzeugung des frequenzmoduliertem Signals wird ein fluidischer Oszillator ver-wendet. Die Schwingungsfrequenz des Oszillators ist von der Größe, der Geometrie und den Druckverhältnissen im Oszillator abhängig, welche durch ein Druckventil veränderbar sind. Zur Datenfassung dienen zwei Laservibrometer. Weiterhin soll die schlussendliche Dicken-bestimmung mithilfe eines Kreuzkorrelationsverfahrens erreicht werden. Während der Ent-wicklung wurden Messungen im Medium Luft, als auch mit Polyamid-Probekörpern durchge-führt. Für die Luftmessungen wurde das Ultraschallsignal an zwei Messpunkten erfasst und der Abstand zwischen diesen Messpunkten daraufhin versucht zu ermitteln. Diese Abstand-messungen wurden mit unterschiedlichen Abständen von 6 bis 15 Zentimeter durchgeführt, wobei der Abstand anhand der Daten mit einer Abweichung von unter einem Zentimeter er-folgreich bestimmt werden konnte. Die Messungen am Probekörper waren weniger Erfolg-reich, da keine reproduzierbare Dickenbestimmung erreicht werden konnte. Trotzdem kann die Entwicklung aufgrund der erfolgreichen Abstandmessung in der Luft sowie den neuen Erkenntnissen aus den Messungen am Probekörper als Erfolg betrachtet werden. KW - Berührungsloser Ultraschall KW - Bauwesen KW - Frequenzmodulation KW - Fluidische Anregung PY - 2019 SP - 1 EP - 74 CY - Berlin AN - OPUS4-50219 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst T1 - Recent advances in NDE of concrete structures at BAM N2 - This talk gives an introduction to BAM and its NDT-CE division. Specific challenges in NDT-CE are discussed as well as recent research results. T2 - NDE 2019 Pre-Conference Tutorial PCT 4 CY - Bangalore, India DA - 03.12.2019 KW - NDT KW - Civil engineering PY - 2019 AN - OPUS4-50168 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst T1 - NDE of foundations N2 - This talk teaches the basic princioles and applications of NDT methods for deep foundations, sprecifically piles. A variety of testing methods are discussed (integrity testing, ultrasonic crosshole logging, parallel seismic and others). Capabilities and limitations are given as well as specific hints for practical use. T2 - NDE 2019 Pre-Conference Tutorial PCT 4 CY - Bangalore, India DA - 03.12.2019 KW - NDT KW - Foundation KW - Pile KW - Integrity testing PY - 2019 AN - OPUS4-50169 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Niederleithinger, Ernst T1 - Ultrasonic methods for concrete: To boldly see, what we have not seen before N2 - This keynote talk at NDE 2019 discusses specific progress in ultrasonic testing of concrete structures. A deep penetration instrument (LAUS) is introduced as well as advanced imaging methods adopted from geophysics and new approaches to ultrasonic monitoring. T2 - NDE 2019 CY - Bangalore, India DA - 05.12.2019 KW - NDT KW - Concrete KW - Ultrasound KW - Imaging KW - Monitoring PY - 2019 AN - OPUS4-50170 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF ED - Zscherpel, Uwe ED - Kasperl, S. T1 - Proceedings of the International Symposium on Digital Industrial Radiology and Computed Tomography (DIR) 2019 N2 - This international symposium is devoted to promote a broad exchange of information on technologies, applications and quality assurance in the area of digital industrial radiology and computed tomography. The meeting provides a unique opportunity for users, scientists, equipment suppliers and all who are interested to discuss the present and future possibilities for industrial applications of the following topics: - Xray detectors and sources - Image processing algorithms - Quantitative imaging - Defect detection & localisation - Feature extraction - Dimensional control - CT, multi-angle - radiography - Laminography & Tomosynthesis - Modelling - Film replacement - Phase contrast - Multi-energies and photon counting - Other radiation techniques (e.g. - neutrons) - Multi-techniques fusion - Standardisation - Qualification & system reliability - Inspection for Additive Manufacturing - Scattering T2 - International Symposium on Digital Industrial Radiology and Computed Tomography (DIR) 2019 CY - Fürth, Germany DA - 02.07.2019 KW - Digital Industrial Radiology KW - Computed Radiography KW - Image Processing PY - 2019 UR - https://www.ndt.net/search/docs.php3?MainSource=264 VL - 264 SP - Paper 24743-1 EP - Paper 24764-17 PB - NDT.net CY - Bad Breisig AN - OPUS4-50519 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zscherpel, Uwe A1 - Funk, Alexander A1 - Gustmann, T. A1 - Jänisch, Gerd-Rüdiger A1 - Ewert, Uwe A1 - Waske, Anja T1 - Röntgentomographie von metallischen Mikropartikeln: Ein leistungsfähiges Werkzeug für die Additive Fertigung N2 - Metallische Mikropartikel in der Größenfraktion von ca. 10 – 100 Mikrometer bilden das Grundmaterial für den additiven Aufbau komplexer Strukturen durch lokales Aufschmelzen mit einem Laserstrahl. Entscheidend für dieses Verfahren ist die Kenntnis der Größen-, Form- und Defektverteilungen von Partikelfraktionen, da sie direkten Einfluss auf die Fließfähigkeit des Pulvers während des lagenweisen Auftragens, als auch auf die finale innere Porosität des Bauteils haben. Im Pulver vorhandene Poren verlassen in der Regel das Schmelzbad vor dem Erstarren nicht wieder, da deren Konvektionszeiten größer sind als die Zeit, während der das lokale Schmelzbad besteht, so dass einmal durch die Ausgangspartikel eingebrachte Poren in der Regel auch im fertigen Bauteil verbleiben. Eine strenge Qualitätskontrolle des Ausgangspulvers ist also Voraussetzung, um hochwertige Bauteile mit geringer Restporosität zu erhalten. Der Vorteil der Röntgentomographie ist dabei, dass mit nur sehr geringem Präparationsaufwand innenliegende Poren bis zu einem Durchmesser von wenigen Mikrometern detektiert werden können. Dies ist mit konkurrierenden Verfahren (Licht- / Elektronenmikroskopie, Laserbeugung) so nicht möglich. Zusammenfassend werden wir zeigen, dass die zerstörungsfreie Bildgebung mit der Röntgen-Mikrotomographie für die Qualitätskontrolle in der additiven Fertigung ein leistungsfähiges Werkzeug ist. Wir erörtern die Grenzen der Methode durch eine numerische Studie mithilfe des Simulationsprogramms aRTist. Dabei werden verschiedene Partikelgrößen dahingehend untersucht, welche Poren mit mikroradiographischen Verfahren detektierbar sind. Dazu wird ein Modell für eine dreilagige dichteste Kugelpackung entwickelt, so dass auch Überlagerungen von Anzeigen untersucht werden können. Im Ergebnis werden verschiedene Partikel- und Porengrößenkombinationen untersucht und die entsprechenden Detektionsgrenzen bestimmt. T2 - DGZfP Jahrestagung 2019 CY - Friedrichshafen, Germany DA - 26.05.2019 KW - Computertomographie KW - Additive Fertigung KW - Mikropartikel PY - 2019 UR - https://jt2019.dgzfp.de/Programm#Di.1.B.1 AN - OPUS4-50520 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zscherpel, Uwe A1 - Nazarzadehmoafi, Maryam A1 - Waske, Anja T1 - Röntgenrückstreutechnik für die additive Fertigung N2 - Neben der klassischen Durchstrahlung wird die bildgebende Röntgen-rückstreuung bisher nur sehr begrenzt eingesetzt. Vor über 20 Jahren hatte Philips mit „COMSCAN“ eine erste industrielle Anwendung in der Luftfahrt gefunden, die sogar eine Tiefenauflösung besaß. Die Firma AS&E in Boston bietet Röntgenrückstreu-Anlagen für den Sicherheitsbereich an. In diesen wird mit einem hochkollimierten Nadelstrahl aus einem rotierenden Blendenrad ein Objekt einseitig abgetastet. Zur Detektion der gestreuten Strahlung aus dem Objekt werden großflächige Detektoren direkt neben dem rotierenden Nadelstrahlkollimator eingesetzt. Ein solcher Prototyp wird an der BAM für den Einsatz in der zerstörungsfreien Prüfung untersucht und optimiert. Als neues industrielles Einsatzgebiet wird dabei die in situ Überwachung in der additiven Fertigung avisiert. Hier ist die Zugänglichkeit zum entstehenden Werkstück in den 3D-Druckanlagen stark eingeschränkt, was den Einsatz einer zweiseitigen Durchstrahlung oder der Computer-Tomographie, bei der das Objekt rotiert wird, verhindert. Auch sind die in der additiven Fertigung eingesetzten Werkstoffe (Polymere, Keramik, Leichtmetalle wie Al oder Ti) für die Rückstreuung besser geeignet als Metalle höherer Dichte, da das Streusignal mit der Ordnungszahl und der Materialdichte abnimmt. Allerdings sind die Anforderungen an räumliche Auflösung und Kontrastempfindlichkeit in der zerstörungsfreien Prüfung additiv gefertigter Bauteil deutlich höher als im Sicherheitsbereich, da hier Bauteilfehler mit typischen Dimensionen kleiner als 1 mm sicher detektiert werden müssen. Die Untersuchung dieser Grenzen des derzeitigen Standes der Röntgenrückstreutechnik mit Nadelstrahl ist ein Teilbereich des mehrjährigen BAM-Themenfeldprojektes „ProMoAM“. Im Vortrag werden die ersten Ergebnisse der Optimierung sowie die gefundenen Anwendungsgrenzen an Beispielen erläutert. T2 - DGZfP Jahrestagung 2019 CY - Friedrichshafen, Germany DA - 26.05.2019 KW - Röntgenrückstreuung KW - Additive Fertigung PY - 2019 UR - https://jt2019.dgzfp.de/Programm#Di.1.B.2 AN - OPUS4-50521 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zscherpel, Uwe A1 - Waske, Anja A1 - Ewert, Uwe T1 - Neues aus der BAM 2019 N2 - Neuentwicklungen im Fachbereich 8.3 "Radiologische Verfahren" der BAM T2 - BHGE Field Radiography Days 2019 CY - Ahrensburg, Germany DA - 03.09.2019 KW - Industrielle Radiographie KW - Zerstörungsfreie Prüfung PY - 2019 AN - OPUS4-50522 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strangfeld, Christoph A1 - Niederleithinger, Ernst A1 - Mielentz, Frank A1 - Effner, Ute A1 - Friedrich, C. A1 - Maulke, R. A1 - Büttner, C. T1 - Qualitätssicherung von Verschlussbauwerken in Endlagern mit Ultraschall N2 - Zur Versiegelung von Endlagern für radioaktive oder chemische Abfälle in ehemaligen Salzbergwerken werden Verschlussbauwerke aus Salzbeton auf ihre Eignung geprüft. Seit einigen Jahren werden durch die Bundesgesellschaft Endlagerung (BGE) und der Bundesanstalt für Materialforschung und -prüfung (BAM) an Versuchsbauwerken Erfahrungen mit der Ultraschalltechnik zur Qualitätssicherung unter Tage gesammelt. Hierbei kommen sowohl kommerzielle und experimentelle Geräte zur Echoprüfung als auch eigens entwickelte Bohrlochsonden zum Einsatz. Alle Geräte basieren auf niederfrequenten s-Wellen-Punktkontaktprüfköpfen (25 kHz– 50 kHz), die in unterschiedlichen Arrays kombiniert werden. In mehreren Versuchsreihen gelang es, unverfüllte und teilverfüllte Risse über mehrere Meter zu verfolgen und in ihrer Lage abzubilden. Technische Einbauten konnten bis in ca. 8 m Tiefe im Bauwerk detektiert werden. Mit Hilfe aus der Geophysik adaptierte Abbildungsverfahren gelang es, einige bisher nicht detektierbare Features sichtbar zu machen. Die Ergebnisse dienen sowohl der Analyse des Versuchsbauwerks als auch der Entwicklung eines Qualitätssicherungssystems für zukünftige reale Verschlussbauwerke. T2 - DACH-Jahrestagung 2019 CY - Friedrichshafen, Germany DA - 27.05.2019 KW - Ultraschall KW - Verschlussbauwerk KW - Endlager KW - Salzbeton PY - 2019 AN - OPUS4-50568 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strangfeld, Christoph A1 - Bühling, Benjamin A1 - Maack, Stefan T1 - Entwicklung eines luftgekoppelten Ultra-schall-Echo-Prüfverfahrens mittels fluidischer Anregung N2 - In vielen technischen Bereichen werden Ultraschallverfahren zur zerstörungsfreien Werkstoffprüfung eingesetzt. Dabei wird ein Schallpuls von einem Prüfkopf in ein Prüfobjekt eingebracht. Der Puls kann unter anderem durch Membranen oder Pie-zoelemente erzeugt werden und wird in der Regel durch direkten Kontakt oder über ein Koppelmittel an das Objekt übertragen. Luftgekoppelter Ultraschall spielt in kommerziellen Anwendungen bisher eine untergeordnete Rolle, da die Differenz der akustischen Impedanzen von Luft und Festkörpern immense Verluste beim Über-gang des Schallsignals hervorruft. In diesem Beitrag soll ein neuartiges Anregungsprinzip vorgestellt werden, mit dem ein Großteil dieser Verluste vermieden wird. Anstelle eines Festkörpers soll mit Hilfe einer fluidischen Düse Druckluft zur Signalerzeugung eingesetzt werden. In dieser Düse wird eine selbsterhaltende Strömungsinstabilität erzeugt, die einen Schallpuls von bis zu 100 kHz hervorruft, sodass der Impedanzverlust in die Umge-bungsluft entfällt. Da die charakteristische Frequenz eines fluidisch generierten Pul-ses maßgeblich von der Bauform der Düse und dem anliegenden Druck abhängt, lässt sich mittels einer geeigneten Strömungsregelung ein breiter Frequenzbereich zur Abtastung nutzen. Die so emittierten Pulse werden auf das Prüfobjekt gerichtet und die reflektierten Signale mit einem Laservibrometer an der Oberfläche des Objekts im Echo-Verfahren abgetastet. Von drei signalmindernden Materialübergängen bei gewöhnlichem luftgekoppeltem Ultraschall bleibt in dem hier vorgeschlagenen Mes-system lediglich die Grenzfläche von Luft zu Prüfkörper, sodass eine höhere Signal-ausbeute als bisher erwartet werden kann. T2 - DACH-Jahrestagung 2019 CY - Friedrichshafen, Germany DA - 27.05.2019 KW - Berührungsloser Ultraschall KW - Fluidische Oszillatoren KW - ZfP im Bauwesen KW - Beton PY - 2019 AN - OPUS4-50569 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zscherpel, Uwe A1 - Nazarzadehmoafi, Maryam A1 - Yuan, Mingshuan A1 - Waske, Anja T1 - X-ray back scatter techniques for additive manufacturing N2 - X-ray back scatter imaging is rarely applied compared to classical X-ray projection imaging. More than 20 years ago the company Philips developed “COMSCAN”, a first application case for aircraft industry, which allowed even a depth resolution using back scatter imaging. The company AS&E in Boston offers back scatter imaging solutions for the security market. The principle is to scan the object with a highly collimated X-ray needle beam from one side only and to detect the backscattered radiation by a large area detector side by side with the collimation wheel. A new prototype is investigated at BAM for application and optimization in non-destructive testing. As modern industrial application field in-situ inspection in additive manufacturing is targeted. The accessibility of the printed part during the production process is very limited. This prevent the application of a two sided X-ray inspection or Computed Tomography, were an rotation of the object is required to acquire projections from 360 degrees. An important advantage for the X-ray back scatter technique are also the materials used in additive manufacturing (polymers, ceramics, light metals like Aluminum or Titanium). These materials with lower density and lower Z values give better scatter signals than metals with higher densities and Z values. The back scatter intensity decreases with increasing density and Z value of the material. But the requirements on spatial resolution and contrast sensitivity are more stringent for non-destructive testing of additive manufactured parts compared to the security area. In NDT sizes of indications smaller than 1 mm have to be detected clearly. The investigation of these limits on a state-of-the-art prototype for X-ray back scattering using rotating collimated X-ray needle beams is a part of the BAM project “ProMoAM”. The contribution shows first results of the optimization for NDT and the achieved application limits for several example cases. T2 - International Symposium on Nondestructive Characterization of Materials CY - Portoroz, Slovenia DA - 17.09.2019 KW - Non-destructive testing KW - X-ray back scattering KW - Additive Manufacturing PY - 2019 AN - OPUS4-50523 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ewert, Uwe A1 - Zscherpel, Uwe A1 - Roth, H. A1 - Matern, D. A1 - Suppes, A. A1 - Schüller, S. A1 - Herlod, F. A1 - Kropas-Hughes, C. T1 - Prediction of the visibility of indications in X-ray computed tomography by the contrast detail diagram N2 - X-Ray Computed Tomography (CT) is applied in industry for flaw detection, flaw evaluation and dimensional measurement. This requires the correct CT system settings for sufficient visibility and detectability of flaws and structure elements. The visibility of indications for human observers on a monitor depends on the square root of the reconstructed flaw area (here pores with diameter < ½ inch) in the cross sectional 2D images, the Contrast to Noise Ratio (CNR) and the Modulation Transfer Function (MTF). This applies also to 2D-projections, meaning also to “normal” digital radiographs. The ASTM guide E 1441 describes three essential functions for prediction of the visibility of small circular indications in slice images of a 3D reconstruction or a 2D reconstruction. This is the Contrast Discrimination Function (CDF), the MTF (see also the revision of ASTM E 1695), and the Contrast Detail Dose (CDD) function. The prediction of the visibility of circular indications in reconstructed slice images can be determined from the Contrast Detail Dose function, which is the combination of CDF and MTF and a physiological factor c. The measurement procedures and formulas for the prediction of the detail visibility by CDD will be corrected, tested and verified by modelling and in a Round Robin Test with modern commercial 3D CT systems of different manufacturers. Conclusions will be reported and recommendations will be given for the correct psychological factor c and the consideration of the influence of artefacts, as e.g. cupping and scatter. T2 - International Symposium on Nondestructive Characterization of Materials CY - Portoroz, Slovenia DA - 17.09.2019 KW - Nondestructive Testing KW - Computed Tomography KW - Visibility of Indications KW - Prediction from system parameters PY - 2019 AN - OPUS4-50524 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zscherpel, Uwe A1 - Ewert, Uwe T1 - Digitale industrielle Rdiographie im Anlagenbau N2 - Der Ersatz von Röntgenfilmen durch digitale Detektoren in der Zerstörungsfreien Prüfung im Anlagenbau wird seit 2013 durch neue ISO-Normen unterstützt. Nach der Erfolgsgeschichte der digitalen Photographie und der fast voll-ständigen Ablösung der Filmtechnik in der optischen Bilderfassung wird erwartet, dass sich der Übergang von der Filmradiographie zur digitalen Radiographie schnell vollzieht. Dieser Trend ist derzeit so noch nicht zu beobachten. Zur mobilen Prüfung wird in Europa immer noch vorrangig die Filmradiographie und nur teilweise die Computerra-diographie mit Speicherfolien eingesetzt. Im Bereich der stationären Prüftechnik haben sich die Matrixdetektoren (DDA) weitgehend durchgesetzt, wobei es auch hier noch alternative Detektoren wie Bildverstärker und Fluorosko-pe gibt. Mit Einführung der DIN EN ISO 17636-2 zur Schweißnahtprüfung wird seit 2013 erstmalig geregelt, wie man einen digitalen Detektor für die technische Radiographie auswählen soll, um im Vergleich zur Filmradiographie eine äquivalente Bildqualität zu erhalten. Essentielle Parameter bestimmen, ob die geforderte Bildgüte (Fehlernachweiß-empfindlichkeit) erreicht wird. Ein Überblick zeigt, welche Parameter für den praktischen Einsatz wichtig sind und wie sie ermittelt werden. Praktische Einsatzbeispiele im Anlagenbau werden diskutiert. T2 - 47. Sondertagung - Schweißen im Anlagenbau CY - Munich, Germany DA - 17.02.2019 KW - Industrielle Radiographie KW - Filmersatz KW - Normung KW - Bildqualitätsnachweis PY - 2019 UR - www.sondertagung.de AN - OPUS4-50525 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zscherpel, Uwe A1 - Ewert, Uwe T1 - Digitale industrielle Radiographie im Anlagenbau N2 - Der Ersatz von Röntgenfilmen durch digitale Detektoren in der Zerstörungsfreien Prüfung im Anlagenbau wird seit 2013 durch neue ISO-Normen unterstützt. Nach der Erfolgsgeschichte der digitalen Photographie und der fast vollständigen Ablösung der Filmtechnik in der optischen Bilderfassung wird erwartet, dass sich der Übergang von der Filmradiographie zur digitalen Radiographie schnell vollzieht. Dieser Trend ist derzeit so noch nicht zu beobachten. Zur mobilen Prüfung wird in Europa immer noch vorrangig die Filmradiographie und nur teilweise die Computerradiographie mit Speicherfolien eingesetzt. Im Bereich der stationären Prüftechnik haben sich die Matrixdetektoren (DDA) weitgehend durchgesetzt, wobei es auch hier noch alternative Detektoren wie Bildverstärker und Fluoroskope gibt. Mit Einführung der DIN EN ISO 17636-2 zur Schweißnahtprüfung wird seit 2013 erstmalig geregelt, wie man einen digitalen Detektor für die technische Radiographie auswählen soll, um im Vergleich zur Filmradiographie eine äquivalente Bildqualität zu erhalten. Essentielle Parameter bestimmen, ob die geforderte Bildgüte (Fehlernachweißempfindlichkeit) erreicht wird. Ein Überblick zeigt, welche Parameter für den praktischen Einsatz wichtig sind und wie sie ermittelt werden. Praktische Einsatzbeispiele im Anlagenbau werden diskutiert. T2 - 47. Sondertagung: Schweißen im Anlagen- und Behälterbau CY - Munich, Germany DA - 19.02.2019 KW - Industrielle Radiographie KW - Digitaler Filmersatz KW - Stand der Normung KW - Bildqualitätsnachweis PY - 2019 SN - 978-3-96144-055-9 VL - 350 SP - 19 EP - 22 PB - DVS Media CY - Düsseldorf AN - OPUS4-50526 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zscherpel, Uwe A1 - Ewert, Uwe A1 - Pittlik, A. T1 - Status of Digital RT Education in Germany considering ISO 9712:2012, the IAEA guidline on DIR and ISO/TS 25107.2:2019 N2 - Status Report on education of personnel for radiographic testing in Germany according to ISO 9712:2012, the IAEA Guideline and ISO/TS 25107 T2 - Seminar NDT Niva 3-Personell CY - Oslo, Norway DA - 11.11.2019 KW - Nondestructive Testing KW - Radiographic Testing KW - Personnel Education KW - Status in Germany KW - Requirements of Standards PY - 2019 AN - OPUS4-50527 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zscherpel, Uwe A1 - Jakubek, J. A1 - Uher, J. T1 - Neue Trends bei Photonen zählenden und Energie auflösenden Detektoren N2 - Die Technologie der hybriden Teilchen (oder Photonen) zählenden Bilddetektoren wurde seit mehr als 2 Jahrzehnten durch Institutionen wie das CERN (MediPix-/ TimePix-Chips) oder das Paul-Scherrer-Institut (Pilatus-/ Eiger-Chips) entwickelt. Die Ursprünge dieser Technologie kommen aus der Hochenergie-Physik mit ihren Beschleuniger-basierten Experimenten, bei denen ein zuverlässiger und rauschfreier Nachweis jedes ionisierten Teilchens gefordert wird. Eine Energieauflösung wird ebenfalls oft verlangr. Das ist auch in der klassischen Radiographie von Nutzen, so wurden diese Detektoren auch dafür optimiert. Neueste Photonen zählenden Detektoren besitzen folgende exzellenten Bildeigenschaften: rauschfreie Photonen-Detektion in einem hohen Dynamikbereich (SNR >2500 erreichbar), hohe räumliche Auflösung (bis zu 10 µm Pixelgröße), Energieschwellen bis zur vollen spektralen Auflösung und eine sehr hohe Geschwindigkeit (bis zu Tausenden Bildern pro Sekunde). Diese hybriden Detektoren können mit hochabsorbierenden Sensorschichten aus CdTe, CZT oder GaAs bestückt werden, um bildgebende Anwendungen mit Gamma- oder harten Röntgenstrahlen zu realisieren, in denen bisher Szintillator basierende Bilddetektoren dominierten (z.B. für NDT, SPECT, PET). Im Beitrag wird der erste wirklich große Photonen zählende Detektor mit CdTe und einer lückenlosen Detektionsfläche, die aus einer theoretisch unbegrenzten Anzahl von MediPix-/ TimePix-Modulen besteht, gezeigt. Die erste kommerzielle Version eines solchen Detektors hat eine Fläche von 7cm x7cm, 1,6 Megapixel und erfüllt die Anforderungen der Prüfklasse „B“ in der industriellen Radiographie. Die Energie auflösenden Fähigkeiten dieses Detektors erlauben eine „Farb-Radiographie“, in der verschiedene Materialien in verschiedene Farben dargestellt werden. Der 2. Teil dieses Beitrags stellt einen voll spektral auflösenden Gamma- und Röntgen-Bilddetektor mit dickem CdTe und 2,4 Megapixel vor, der auf TimePix3-Chips basiert und eine sehr hohe Ortsauflösung von ~10 µm erreicht. Die hohe Zeitauflösung von TimePix3 wird mit großem Nutzen für eine substantielle Verbesserung der erhaltenen Bilder und Spektren zur Unterdrückung interner Fluoreszenzstrahlung sowie Comptonstreuungsanteilen, die die Bildinformation verschmieren, verwendet. T2 - 18. Seminar der DGZfP zu aktuellen Fragen der Durchstrahlungsprüfung und des Strahlenschutzes CY - Kassel, Germany DA - 28.03.2019 KW - Radiographische Prüfung KW - Direktumwandelnde Detektoren KW - Energieauflösende Detektoren PY - 2019 AN - OPUS4-50528 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zscherpel, Uwe A1 - Ewert, Uwe T1 - Aktuelle Entwicklungen in der Standardisierung N2 - In den letzten zwei Jahren wurden 11 neue Standards/Standardrevisionen zur RT veröffentlicht (ohne Strahlenschutz) und 5 werden dafür gestrichen. Es wird über die neuen Anforderungen ausgewählter Normen bzw. Normrevisionen informiert und insbesondere auch über die veränderten Parameter, die bei Prüfpraxis und bei der Klassifizierung zu berücksichtigen sind. Das wichtigste Projekt ist die Revision der DIN EN ISO 17636-1, -2, RT von Schweißverbindungen, in ISO TC 44 SC 5 WG 1. Die Standards zur Schweißnahtprüfung in der Kerntechnik, DIN 25435, wurden ins Englische übertragen und bei ISO TC 85 SC 6 bearbeitet. Hauptaktivität bei ASTM ist gegenwärtig die Überarbeitung der CT-Standards und die Berücksichtigung der Anforderungen an das dimensionelle Messen. Der Guide ASTM E 1441 zur Bestimmung von MTF, Kontrast-Detail-Funktion (CDF) und Kontrast-Diskrimination-Diagramm (CDD) wird revidiert. E 2445 zur CR Long Term Stability wird ebenfalls revidiert. Die Revision soll auch in die ISO 16371-1 eingehen. Dazu ist ein Round Robin-Test geplant. Auch die Standards zur Durchstrahlungsprüfung auf Korrosion und Ablagerungen in Rohren mit Röntgen- und Gammastrahlen (EN 16407-1, -2, 2014) wurden revidiert. Diese Revision wurde als DIN EN ISO 20769-1, -2 2018 veröffentlicht und EN 16407 wird zurückgezogen. Die Revision der Standards EN 12543 und EN 12679 zur Messung der Brennfleckgröße und der Strahlergröße ist mit Verzögerung in Überarbeitung, um die digitalen Detektoren und Messmöglichkeiten mit Bildverarbeitungsprogrammen zu berücksichtigen. Ein Entwurf zur Messung der Brennfleckgröße von nano-Fokusröhren wird derzeit vom Europäischen Metrologie-Programm EMPIR gefördert. Zur radiographischen Gussteilprüfung wurde der Standard EN 12681 revidiert und 2018 veröffentlicht. Er wurde um Zulässigkeitsgrenzen erweitert und die digitale Radiographie wurde in Teil 2 berücksichtigt. T2 - 18. Seminar der DGZfP zu aktuellen Fragen der Durchstrahlungsprüfung und des Strahlenschutzes CY - Kassel, Germany DA - 28.03.2019 KW - Radiographische Prüfung KW - Standardisierung bei DIN, CEN und ISO KW - DGZfP-Richtlinien PY - 2019 AN - OPUS4-50529 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zscherpel, Uwe T1 - X-ray back scatter techniques for additive manufacturing N2 - X-ray back scatter imaging is rarely applied compared to classical X-ray projection imaging. 20 years ago the company Philips developed “COMSCAN”, a first application case in the aircraft industry, which allowed even a depth resolution using back scatter imaging. The company AS&E in Boston offers back scatter imaging solutions for the security market. Their principle is to scan the object with a highly collimated X-ray needle beam from one side only and detect the backscattered radiation by a large area detector side by side with the collimation wheel. A new prototype is investigated at BAM for application and optimization in non-destructive testing. As modern industrial application field in-situ testing in additive manufacturing is targeted. The accessibility of the printed part during the production process is very limited. This prevent the application of a two sided X-ray inspection or Computed Tomography, were an rotation of the object is required to acquire projections from 360 degrees. An important advantage for the X-ray back scatter technique are also the materials used in additive manufacturing (polymers, ceramics, light metals like Aluminum or Titanium). These materials with lower density and lower Z values give better scatter signals than metals with higher densities and Z values. The back scatter intensity decreases with increasing density and Z value of the material. But the requirements on spatial resolution and contrast sensitivity are more stringent for non-destructive testing of additive manufactured parts compared to the security area. In NDT sizes of indications smaller than 1 mm have to be detected clearly. The investigation of these limits on a stateof-the-art prototype for X-ray back scattering using rotating collimated X-ray needle beams is a part of the BAM project “ProMoAM”. The contribution shows first results of the optimization for NDT and the achieved application limits for several example cases. T2 - International symposium on digital industrial radiology and computed tomography DIR2019 CY - Fürth, Germany DA - 02.07.2019 KW - Radiographic testing KW - X-ray back scattering KW - Additive manufacturing PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-505317 UR - https://www.ndt.net/search/docs.php3?id=24760 AN - OPUS4-50531 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Osterloh, Kurt A1 - Röhrs, S. A1 - Schwabe, A. A1 - Radujcovic, S. A1 - Bücherl, T. A1 - Dangendorf, V. A1 - Zscherpel, Uwe A1 - Reiche, I. A1 - Nüsser, A. ED - Zscherpel, Uwe ED - Kasperl, S. T1 - Elucidating the distribution of organic consolidants in wood by Neutron Tomography N2 - While the absorption of X-rays and gamma radiation is determined by the Z-number of the elements a specimen is composed of, it is the hydrogen making an effective contrast with neutron imaging. As a consequence, interrogating with neutrons presents a suitable tool to study the distribution of organic consolidants in materials such as wood as encountered in impregnated wooden artworks. Four different examples of objects are presented here to demonstrate the potential of neutron CT: 1) small wooden pieces of ship wrecks (< 2 cm thickness) interrogated with cold neutrons (0.5 meV at the ANTARES facility of the FRM II in Garching) to demonstrate the potential and the limitation of using low energy neutrons, 2) a wooden statue soaked with carbolineum (fission neutrons 1.8 MeV at the NECTAR facility of the FRM II), 3) a smaller wooden figure of a skull heavily soaked with carbolineum so it was too tight for the fission neutrons used before with accelerator neutrons (broad range about 5.5 MeV at the PTB in Braunschweig) and 4) pieces of charred wood to study the impregnation with a consolidant (NECTAR, FRM II). With the exception of the last example, all results have been combined with X-ray tomography (BAM 8.3 in Berlin). In the case of the charred wood specimens (example 4) the density histograms of the neutron tomography results were compared with those obtained from untreated references. The observed gain in specific density of the soaked specimens corresponded with an increase of specific weight. All results obtained so far showed distinct distribution patterns attributable to structural peculiarities or organic consolidants providing valuable support for subsequent restoration works. T2 - International symposium on digital industrial radiography and computed tomography DIR2019 CY - Fürth, Germany DA - 02.07.2019 KW - Neutron Imaging KW - Cold to fast neutron testing KW - Tomography of wood samples KW - Art restauration PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-505326 UR - https://www.ndt.net/search/docs.php3?id=24740 SN - 1435-4934 VL - 24 IS - 11 SP - 1 EP - 8 PB - NDT.net CY - Kirchwald AN - OPUS4-50532 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zscherpel, Uwe A1 - Ewert, Uwe T1 - Annual report of sub commission V-A “Radiography-based weld inspection” N2 - Report on the annual activities of IIW commission V, Sub-Commission V-A "Radiography based weld inspection" chaired by Uwe Zscherpel, BAM Berlin T2 - 72. Annual Assembly of the International Institute of Welding 2019 CY - Bratislava, Slovakia DA - 07.07.2019 KW - International Institute of Welding KW - Sub-Commission V-A KW - Radiography based weld inspection PY - 2019 AN - OPUS4-50533 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zscherpel, Uwe A1 - Nazarzadehmoafi, Maryam A1 - Yuan, Mingchuan A1 - Waske, Anja T1 - X-ray back scatter techniques for additive manufacturing N2 - X-ray back scatter imaging is rarely applied compared to classical X-ray projection imaging. 20 years ago the company Philips developed “COMSCAN”, a first application case in the aircraft industry, which allowed even a depth resolution using back scatter imaging. The company AS&E in Boston offers back scatter imaging solutions for the security market. Their principle is to scan the object with a highly collimated X-ray needle beam from one side only and detect the backscattered radiation by a large area detector side by side with the collimation wheel. A new prototype is investigated at BAM for application and optimization in non-destructive testing. As modern industrial application field in-situ testing in additive manufacturing is targeted. The accessibility of the printed part during the production process is very limited. This prevent the application of a two sided X-ray inspection or Computed Tomography, were an rotation of the object is required to acquire projections from 360 degrees. An important advantage for the X-ray back scatter technique are also the materials used in additive manufacturing (polymers, ceramics, light metals like Aluminum or Titanium). These materials with lower density and lower Z values give better scatter signals than metals with higher densities and Z values. The back scatter intensity decreases with increasing density and Z value of the material. But the requirements on spatial resolution and contrast sensitivity are more stringent for non-destructive testing of additive manufactured parts compared to the security area. In NDT sizes of indications smaller than 1 mm have to be detected clearly. The investigation of these limits on a stateof-the-art prototype for X-ray back scattering using rotating collimated X-ray needle beams is a part of the BAM project “ProMoAM”. The contribution shows first results of the optimization for NDT and the achieved application limits for several example cases. T2 - 72. annual assembly of the international institute of welding 2019 CY - Bratislava, Slovakia DA - 07.07.2019 KW - Nondestructive tesing KW - X-ray back scattering KW - Additive manufacturing PY - 2019 AN - OPUS4-50534 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zscherpel, Uwe A1 - Stegemann, Robert T1 - Revision of ISO 24497 – NDT – Metal Magnetic Memory (MMM) N2 - The revision of ISO 24497:2007 started in 2017 (by decision of Com-V at the IIW annual assembly in Shanghai). After 3 years of discussions and incorporation of many comments from all over the world the working group C-V-E-b headed by Uwe Zscherpel finalized the work with a final draft to be forwarded for final vote at ISO TC 44. The working group C-V-E-b finalised the work and can be resolved. The chair thanks for all the successfully work done, the vote to forward the latest draft to ISO for final vote was done without any negative. T2 - 72. Annaul assebly of the international institute of welding CY - Bratislava, Slovakia DA - 07.07.2019 KW - International Institute of Welding KW - General Assembly KW - Revision of ISO 24497 KW - Metal Magnetic Memory PY - 2019 AN - OPUS4-50535 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Zscherpel, Uwe A1 - Ewert, Uwe T1 - Aktuelle Entwicklungen in der Standardisierung N2 - In den letzten zwei Jahren wurden 11 neue Standards/Standardrevisionen zur RT veröffentlicht (ohne Strahlenschutz) und 5 werden dafür gestrichen. Es wird über die neuen Anforderungen ausgewählter Normen bzw. Normrevisionen informiert und insbesondere auch über die veränderten Parameter, die bei Prüfpraxis und bei der Klassifizierung zu berücksichtigen sind. Das wichtigste Projekt ist die Revision der DIN EN ISO 17636-1, -2, RT von Schweißverbindungen, in ISO TC 44 SC 5 WG 1. Die Standards zur Schweißnahtprüfung in der Kerntechnik, DIN 25435, wurden ins Englische übertragen und bei ISO TC 85 SC 6 bearbeitet. Hauptaktivität bei ASTM ist gegenwärtig die Überarbeitung der CT-Standards und die Berücksichtigung der Anforderungen an das dimensionelle Messen. Der Guide ASTM E 1441 zur Bestimmung von MTF, Kontrast-Detail-Funktion (CDF) und Kontrast-Diskrimination-Diagramm (CDD) wird revidiert. E 2445 zur CR Long Term Stability wird ebenfalls revidiert. Die Revision soll auch in die ISO 16371-1 eingehen. Dazu ist ein Round Robin-Test geplant. Auch die Standards zur Durchstrahlungsprüfung auf Korrosion und Ablagerungen in Rohren mit Röntgen- und Gammastrahlen (EN 16407-1, -2, 2014) wurden revidiert. Diese Revision wurde als DIN EN ISO 20769-1, -2 2018 veröffentlicht und EN 16407 wird zurückgezogen. Die Revision der Standards EN 12543 und EN 12679 zur Messung der Brennfleckgröße und der Strahlergröße ist mit Verzögerung in Überarbeitung, um die digitalen Detektoren und Messmöglichkeiten mit Bildverarbeitungsprogrammen zu berücksichtigen. Ein Entwurf zur Messung der Brennfleckgröße von nano-Fokusröhren wird derzeit vom Europäischen Metrologie-Programm EMPIR gefördert. Zur radiographischen Gussteilprüfung wurde der Standard EN 12681 revidiert und 2018 veröffentlicht. Er wurde um Zulässigkeitsgrenzen erweitert und die digitale Radiographie wurde in Teil 2 berücksichtigt. T2 - 17. Seminar der DGZfP "Aktuelle Fragen der Durchstrahlungsprüfung und des Strahlenschutzes" CY - Kassel, Germany DA - 28.03.2019 KW - Digitale Radiographie KW - Standards KW - Bildqualität KW - Klassifizierung PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-505371 UR - https://www.ndt.net/search/docs.php3?id=24807 VL - 24 IS - 12 SP - 1 EP - 5 PB - NDT.net CY - Kirchwald AN - OPUS4-50537 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heckel, Thomas A1 - Casperson, Ralf A1 - Gaal, Mate A1 - Pelkner, Matthias A1 - Prager, Jens T1 - Forschungsthemen im Bereich der ZfP mit akustischen und elektromagnetischen Methoden N2 - Die zerstörungsfreien Methoden zur Untersuchung und Charakterisierung von Materialien sowie zur Detektion von betriebsbedingten und herstellungsbedingten Fehlern mit akustischen und elektrischen Methoden werden vorgestellt. Schwerpunkt bilden die Ultraschall-, die Wirbelstrom- und die Streuflussprüfung. Die Verfahren werden anhand des Aufgabenspektrums des Fachbereiches 8.4 der BAM dargestellt. T2 - Lehrveranstaltung 0334 L 119 „Instrumentelle Analytik“ innerhalb des Moduls „Untersuchungsverfahren“ im Masterstudium des Studiengangs Werkstoffwissenschaften CY - BAM Berlin, Germany DA - 06.12.2019 KW - Ultraschallprüfung KW - Wirbelstromprüfung KW - Streuflussprüfung PY - 2019 AN - OPUS4-50014 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Puthiyaveettil, N. A1 - Thomas K, R. A1 - Unnikrishnakurup, S. A1 - Myrach, Philipp A1 - Ziegler, Mathias A1 - Balasubramaniam, K. T1 - Laser line scanning thermography for surface breaking crack detection modeling and experimental study N2 - Crack detection in metallic samples at high surface temperature, hostile and hazardous environments, etc. is challenging situation in any manufacturing industries. Most of the present NDE methods are suitable only for lower surface temperatures, especially room temperature. In this situation, we need a fast and non-contact NDT method which can be applied even in high sample surface temperature. Laser thermography is one of the techniques having a high potential in non-contact inspection. As a preliminary investigation, in this article, we have studied the potentiality of laser line thermography in crack detection at room temperature. In laser line thermography, a continuous wave (CW) laser is used to generate a laser line, which in turn is used to scan the metal surface. The heat distribution over the sample surface is recorded by an infrared thermal (IR) camera. Two different approaches are reported in this work. Firstly, a stationary laser line source and its interaction with cracks; secondly, moving laser line source scanning over a surface with crack. When the distance between crack centre to laser line centre increases, crack detectability will decrease; and when laser power increases, crack detectability will increase. A dedicated image processing algorithm was developed to improve the detectability of the cracks. To understand the heat transfer phenomenon, a simplified 3D model for laser thermography was developed for the heat distribution during laser heating and was validated with experimental results. Defects were incorporated as a thermally thin resistive layer (TTRL) in numerical modeling, and the effect of TTRL in heat conduction is compared with experimental results. KW - Thermography KW - Laser Thermography KW - Cracks KW - FEM KW - NDT PY - 2019 DO - https://doi.org/10.1016/j.infrared.2019.103141 VL - 104 SP - 103141 PB - Elsevier B.V. AN - OPUS4-49941 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Z., Zhang A1 - Ewert, Uwe A1 - Barrett, T. D. A1 - Bond, L. J. T1 - Paper Watermark Imaging using Electron and Low Energy X-ray Radiography N2 - Historians and librarians are interested in watermarks and mould surface patterns in historic papers, because they represent the “fingerprints” of antique papers. However, these features are usually covered or hidden by printing, writing or other media. Different techniques have been developed to extract the watermarks in the paper while avoiding interference from media on the paper. Beta radiography provides good results, but this method cannot be widely used because of radiation safety regulations and the long exposure times required due to weak isotope sources employed. In this work, two promising methods are compared which can be used to extract digital high-resolution images for paper watermarks and these are electron radiography and low energy X-ray radiography. For electron radiography a “sandwich” of a lead sheet, the paper object, and a film in a dark cassette, is formed and it is exposed at higher X-ray potentials (> 300 kV). The photoelectrons escaping from the lead sheet penetrate the paper and expose the film. After development, the film captures the watermark and mould surface pattern Images for the paper being investigated. These images are then digitized using an X-ray film digitizer. The film employed could potentially be replaced by a special type of imaging plate with a very thin protection layer to directly generate digital Images using computed radiography (CR). For the second method, a low energy X-ray source is used with the specimen paper placed on a digital detector array (DDA). This method directly generates a low energy digital radiography (DR) image. Both methods provide high quality images without interference from the printing media, and provide the potential to generate a “fingerprint” database for historical papers. There were nevertheless found to be differences in the images obtained using the two methods. The second method, using a low energy X-ray source, has the potential to be integrated in a portable device with a small footprint incorporating user safety requirements. Differences obtained using the two methods are shown and discussed. T2 - 45th Annual Conference on Review of Progress in Quantitative Nondestructive Evaluation (QNDE) CY - Burlington, VT, USA DA - 15.07.2018 KW - X-ray Radiography KW - Paper watermark PY - 2019 SN - 978-0-7354-1832-5 DO - https://doi.org/10.1063/1.5099750 SN - 0094-243X VL - 2102 IS - 1 SP - 030004-1 EP - 030004-9 PB - American Institute of Physics AN - OPUS4-49922 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Greco, A. A1 - Starostin, V. A1 - Karapanagiotis, C. A1 - Hinderhofer, A. A1 - Gerlach, A. A1 - Pithan, L. A1 - Liehr, Sascha A1 - Schreiber, Frank A1 - Kowarik, Stefan T1 - Fast fitting of reflectivity data of growing thin films using neural networks N2 - X-ray reflectivity (XRR) is a powerful and popular scattering technique that can give valuable insight into the growth behavior of thin films. This study Shows how a simple artificial neural network model can be used to determine the thickness, roughness and density of thin films of different organic semiconductors [diindenoperylene, copper(II) phthalocyanine and alpha-sexithiophene] on silica from their XRR data with millisecond computation time and with minimal user input or a priori knowledge. For a large experimental data set of 372 XRR curves, it is shown that a simple fully connected model can provide good results with a mean absolute percentage error of 8–18% when compared with the results obtained by a genetic least mean squares fit using the classical Parratt formalism. Furthermore, current drawbacks and prospects for improvement are discussed. KW - Artificial neural networks KW - X-ray reflectivity PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-498997 DO - https://doi.org/10.1107/S1600576719013311 SN - 1600-5767 VL - 52 SP - 1342 EP - 1347 PB - Wiley AN - OPUS4-49899 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kowarik, Stefan A1 - Krebber, Katerina T1 - Smart materials and structures based on fiber optic sensing N2 - This talk gives an overview of basic techniques. Towards the end some applications of neural networks are discussed. T2 - BAM - IFW workshop CY - Berlin, Germany DA - 25.11.2019 KW - Artificial neural networks KW - Fiber optic sensing PY - 2019 AN - OPUS4-49901 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kowarik, Stefan A1 - Krebber, Katerina T1 - Neue Entwicklungen der Faseroptische Sensorik: von Infrastruktur-Monitoring zu neuronalen Netzen N2 - Der Vortrag gibt eine Einführung zu obigen Themen auf Niveau von Master Studierenden. T2 - TUM-Tag CY - BAM, Berlin, Adlershof DA - 19.06.2019 KW - Faseroptische Sensorik PY - 2019 AN - OPUS4-49902 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völker, Christoph T1 - Trainingsworkshop Datenanalyse N2 - Wir laden zum Trainingsworkshop Datenanalyse ein. Angetrieben durch die Digitalisierung und die sogenannte Industrie 4.0 steigt die Erwartungshaltung gegenüber der Nutzung von Daten. Die Unsicherheit, Widersprüchlichkeit und Redundanz separat verarbeiteter einzelner Quellen soll durch die synergetische Zusammenführung heterogener Datensätze überwunden werden. Dabei steht der zunehmenden Aufgabenkomplexität eine ebenso zunehmende Verfügbarkeit an Daten und Analyseverfahren gegenüber. Der Workshop vermittelt ein konzeptionelles Verständnis für moderne Datenanalyseverfahren (Machine Learning (ML), Multivariate Statistik) und soll durch ein anschließendes Hands-On Training mit Python (https://www.python.org) einen einfachen Einstieg in die Thematik ermöglichen. Der Kurs richtet sich an den wissenschaftlichen Nachwuchs. T2 - Trainingsworkshop KDA: Schwerpunkt Machine Learning und Python CY - Berlin, Germany DA - 03.06.2019 KW - KDA Training KW - Data Analysis KW - Machine Learning PY - 2019 AN - OPUS4-49860 LA - mul AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heckel, Thomas A1 - Wack, Y. A1 - Mook, G. T1 - Simulation of an instrumented ultrasonic test run with a rail inspection train N2 - Rail inspection performed by ultrasonic rail inspection trains is a complex and challenging process. A large number of variables and parameters given by the environment, the track and the testing-system have an influence on the overall performance of the inspection and the inspection result. Typically the parameter vary in a combination depending on the track condition. To evaluate the individual influence of each relevant variable, simulation tools can be used. Therefore the entire inspection process has to be transferred into a model using combined modelling techniques. The goal of this work is to model an instrumented ultrasonic test run with a rail inspection train with the parameters varied by a script over a virtually driven distance. T2 - 46th Annual Review of Progress in Quantitative Nondestructive Evaluation- QNDE 2019 CY - Portland, OR, USA DA - 14.07.2019 KW - Ultrasound KW - Rail inspection KW - Modelling KW - Simulation PY - 2019 VL - 2019 SP - 1 EP - 3 AN - OPUS4-49839 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ahmadi, Samim A1 - Ziegler, Mathias A1 - Thiel, Erik A1 - Hirsch, Philipp Daniel A1 - Karagianni, Christina A1 - Burgholzer, P. A1 - Mayr, G. A1 - Jung, P. A1 - Caire, G. T1 - Thermal Super Resolution Image Reconstruction Using Structured Laser Heating N2 - The separation of two closely located defects in fields of Thermographic NDE is very challenging. The diffusive nature of thermal waves leads to a fundamental limitation in spatial resolution. Therefore, super resolution image reconstruction can be used. The measured thermal waves can be transformed to virtual (ultrasound) waves that can be processed by applying ultrasound reconstruction algorithms and finally the super resolution algorithm. Otherwise, it is also possible to make use of a Fourier transform with a subsequent super resolution routine. These super resolution thermographic image reconstruction techniques in post-processing are discussed and evaluated regarding performance, accuracy and repeatability. T2 - 7th Autumn School METTI (Thermal Measurements and Inverse Techniques) CY - Porquerolles Island, Hyères, France DA - 29.09.2019 KW - Super resolution KW - Virtual wave KW - Laser thermography KW - VCSEL array KW - Joint sparsity KW - Compressed sensing PY - 2019 AN - OPUS4-49881 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ziegler, Mathias A1 - Ahmadi, Samim A1 - Hirsch, Philipp Daniel A1 - Karagianni, Christina A1 - Burgholzer, P. A1 - Mayr, G. A1 - Jung, P. A1 - Caire, G. T1 - Verbesserung des räumlichen Auflösungsvermögens der Impuls-Thermografie durch strukturierte Laser-Erwärmung und Joint Sparsity Rekonstruktion N2 - Die thermografische ZfP basiert auf der Wechselwirkung von thermischen Wellen mit Inhomogenitäten. Diese Inhomogenitäten hängen mit der Probengeometrie oder der Materialzusammensetzung zusammen. Obwohl die Thermografie für ein breites Spektrum von Inhomogenitäten und Materialien geeignet ist, ist die grundlegende Einschränkung die diffuse Natur der thermischen Wellen und die Notwendigkeit, ihre Wirkung lediglich an der Probenoberfläche radiometrisch messen zu können. Die Ausbreitung der thermischen Wellen von der Wärmequelle über die Inhomogenität zur Detektionsoberfläche führt zu einer Verschlechterung des räumlichen Auflösungsvermögens der thermografischen Technik. Ein neuer konzertierter Ansatz auf Basis einer räumlich strukturierten Erwärmung und einer Joint Sparsity des Signalensembles ermöglicht eine verbesserte Rekonstruktion von Inhomogenitäten. Im Beitrag wird die Implementierung dieses Ansatzes auf Basis einer strukturierten Beleuchtung mit einem 1D-Laser-Array vorgestellt. Die einzelnen Emitterzellen des Laser-Arrays werden durch ein pseudozufälliges Binärmuster gesteuert und zusätzlich leicht verschoben. Die wiederholte Messung dieser verschiedenen Konfigurationen bei gleichzeitig konstanter Inhomogenität ermöglicht eine Rekonstruktion der Inhomogenität unter Ausnutzung der Joint Sparsity. T2 - Thermographie Kolloquium 2019 CY - Halle, Germany DA - 19.09.2019 KW - Thermografie KW - Laser-Thermografie KW - ZfP KW - Compressed Sensing KW - Super Resolution PY - 2019 AN - OPUS4-49938 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kupsch, Andreas A1 - Müller, Bernd R. A1 - Bruno, Giovanni A1 - Lange, A. A1 - Hentschel, M.P. A1 - Laquai, René T1 - Materialcharakterisierung mittels bildgebender Röntgenstreuverfahren N2 - Die herkömmliche Bildgebung mit Röntgenstrahlung beruht auf unterschiedlicher Absorption durch verschiedene Materialien im Volumen eines Körpers. Es entsteht ein "Massebild". Die hier vorgestellten Verfahren benutzen die Brechung und Beugung von Röntgenstrahlen, um innere Oberflächen oder die Molekulartextur von Materialien und Bauteilen abzubilden. Im Vortrag werden die entsprechenden Messtechniken an der BAM im Labormaßstab sowie an Großforschungseinrichtungen vorgestellt und anhand einiger Anwendungsbeispiele die zusätzlichen Informationen zur herkömmlichen Durchstrahlung diskutiert. T2 - 243. Sitzung DGZfP-Arbeitskreis Thüringen CY - Ilmenau, Germany DA - 11.04.2019 KW - Röntgenrefraktion KW - Röntgenbeugung KW - Diffraction Enhanced Imaging KW - Keramik KW - Polyethylen KW - Metall-Matrix-Komposit PY - 2019 AN - OPUS4-49859 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bellon, Carsten T1 - Radiographic Simulator aRTist - Computer simulation for industrial Tomography N2 - aRTist is an easy-to-use and practical simulation tool to generate realistic radiographic images from CAD objects. A dedicated add-on module makes CT simulation easy (virtual computer tomography). Just choose the number of projections. Unlike in the practice, simulation can separately image the primary and scatter radiation. This allows studying the scattering artefacts in CT (gray-level variations in regions of homogeneous material). T2 - 5. Jenaer μCT-Workshop CY - Jena, Germany DA - 20.11.2019 KW - Vitual computer tomography simulation PY - 2019 AN - OPUS4-49826 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Casperson, Ralf A1 - Pohl, Rainer A1 - Lohde, Sebastian A1 - Aydoğdu, M. T1 - Non-Destructive Testing of Composite Pressure Vessels using Conventional and High-Frequency Eddy Current Technique N2 - Composite-Druckgefäße für den Gefahrguttransport sowie für Wasserstoff- und Erdgasfahrzeuge bestehen aus einem lasttragenden Composite und einer gasdichten, metallischen oder polymeren Barriereschicht (Liner). Zur Untersuchung des Alterungsverhaltens solcher Composite-Druckgefäße wurde in der BAM das interdisziplinäre Themenfeldprojekt COD-AGE durchgeführt. Ziel des Projektes war die Entwicklung von Methoden und Modellen zur Beschreibung und Bestimmung des Alterungsverhaltens von Carbonfaser-Compositen am Beispiel von Druckgefäßen, um eine bessere Vorhersage der Alterung und der sicheren Gebrauchsdauer zu ermöglichen. Ein Schwerpunkt in diesem Projekt war die Bereitstellung geeigneter ZfP-Methoden. Dabei ging es sowohl um versuchsbegleitende Prüfungen, als auch um die mögliche Entwicklung von Prüfeinrichtungen für den späteren praktischen Gebrauch. In dem Vortrag werden Prüfergebnisse der alterungsbegleitenden Wirbelstromprüfung an Composite-Druckgefäßen vorgestellt. In Alterungsversuchen wurden Druckgefäße aus einem ca. 4 mm dicken Aluminiumliner und ca. 8 mm dicker CFK-Ummantelung untersucht. Typisches Einsatzgebiet solcher Druckgefäße sind Atemschutzgeräte der Feuerwehr. Die Druckgefäße wurden sowohl mit konventioneller Wirbelstromtechnik von außen und von innen als auch mit hochfrequenter Wirbelstromtechnik von außen geprüft. Es konnten sowohl Beschädigungen des metallischen Liners, als auch Strukturen des CFK-Geflechts nachgewiesen werden. Eine besondere mechanische Herausforderung bestand in der Prüfung der Innenseite der Liner, da hier eine zylindrische Fläche mit einem Innendurchmesser von 150 mm durch einen Zugang von nur 15 mm Durchmesser geprüft werden muss. N2 - Composite pressure vessels for transporting dangerous goods and for hydrogen and natural gas vehicles consist of a load-bearing composite and a gas-tight, metallic or polymeric barrier layer (liner). To investigate the aging behavior of such composite pressure vessels, BAM carried out the interdisciplinary project COD-AGE. The aim of the project was the development of methods and models for the description and determination of the aging behavior of carbon fiber composites using the example of pressure vessels in order to better predict aging and safe working life. One focus of this project was the provision of suitable NDT methods. These included both test-related tests and the possible development of test equipment for later practical use. In the lecture, test results of the age-related eddy current test on composite pressure vessels are presented. In aging tests, pressure vessels made of an approximately 4 mm thick aluminum liner and approx. 8 mm thick CFRP layer were examined. Typical application of such pressure vessels are respiratory protective devices of the fire department. The pressure vessels were tested using conventional eddy current technology from the outer and inner side as well as with high-frequency eddy current technology. Both damage to the metallic liner and structures of the CFRP could be detected. A particular mechanical challenge was the inspection of the inside of the liners, since a cylindrical surface with an inside diameter of 150 mm has to be tested with an access of only 15 mm diameter. T2 - TAHYA-Workshop CY - Berlin, Germany DA - 27.11.2019 KW - NDT KW - Composite pressure vessel KW - CFRP KW - Eddy current testing PY - 2019 AN - OPUS4-49829 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gaal, Mate A1 - Bente, Klaas A1 - Hufschläger, Daniel T1 - Air-coupled ultrasonic sensors N2 - We present an overview of air-coupled ultrasonic transducers. T2 - Workshop BAM-IWF CY - Berlin, Germany DA - 25.11.2019 KW - Air-coupled transducers KW - Ferroelectret KW - Thermoacoustics KW - Plasma PY - 2019 AN - OPUS4-49806 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Boehm, Rainer T1 - Phased Array und Imaging, zwei raumzeitliche Interferenzverfahren N2 - Phased-Array-Technik und Bildgebung mit Ultraschallwellen sind nach langer Entwicklungszeit inzwischen auf dem Weg zu allgemeiner Verbreitung. Daher bietet sich an, die verschiedenen Techniken und deren Begriffe wie z.B. Phased-Array, SAFT, TFM, FMC und Sparse-Array zusammenfassend in Beziehung zu setzen. All diesen Techniken liegt dieselbe Idee zu Grunde, nämlich durch gezielte Überlagerung von Ultraschallsignalen den gewünschten Effekt zu erreichen. Die verschiedenen Techniken werden kurz charakterisiert und neben den Unterschieden wird beschreiben, auf welche Weise bei all diesen Techniken das Phänomen der konstruktiven Interferenz jeweils genutzt wird. T2 - Ultraschall-Array-Technologien und ihre Anwendungen, Seminar des FA Ultraschallprüfung der DGZfP CY - Berlin, Germany DA - 04.11.2019 KW - Phased Array KW - Imaging KW - Synthetic Aperture Focusing Technique KW - Total Focusing Methode KW - Full Matrix Capture PY - 2019 UR - https://www.dgzfp.de/seminar/ultraschall# AN - OPUS4-49791 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Boehm, Rainer T1 - Phased Array und Imaging, zwei raumzeitliche Interferenzverfahren N2 - Phased-Array-Technik und Bildgebung mit Ultraschallwellen sind nach langer Entwicklungszeit inzwischen auf dem Weg zu allgemeiner Verbreitung. Daher bietet sich an, die verschiedenen Techniken und deren Begriffe wie z.B. Phased-Array, SAFT, TFM, FMC und Sparse-Array zusammenfassend in Beziehung zu setzen. All diesen Techniken liegt dieselbe Idee zu Grunde, nämlich durch gezielte Überlagerung von Ultraschallsignalen den gewünschten Effekt zu erreichen. Die verschiedenen Techniken werden kurz charakterisiert und neben den Unterschieden wird beschreiben, auf welche Weise bei all diesen Techniken das Phänomen der konstruktiven Interferenz jeweils genutzt wird. T2 - Ultraschall-Array-Technologien und ihre Anwendungen, Seminar des FA Ultraschallprüfung der DGZfP CY - Berlin, Germany DA - 04.11.2019 KW - Phased Array KW - Imaging KW - Synthetic Aperture Focusing Technique KW - Total Focusing Methode KW - Full Matrix Capture PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-497924 UR - https://www.dgzfp.de/seminar/ultraschall# SP - 1 EP - 20 PB - DGZfP AN - OPUS4-49792 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bulling, Jannis A1 - Gravenkamp, H. T1 - Comparison of different models for stress singularities in higher order finite element methods for elastic waves N2 - In this contribution, we present three models to capture singularities in combination with the Spectral Element Method. The first model, the continued-fraction-based Scaled Boundary Finite Element Method, the second model, a new approach based on enrichment with static modes, and the third model, which uses an hp-refinement near the singularity, are compared among each other and evaluated in terms of their respective efficiency and accuracy. T2 - GAMM 2019 CY - Wien, Austria DA - 18.02.2019 KW - Enriched finite element method KW - Scaled boundary finite element method PY - 2019 DO - https://doi.org/10.1002/pamm.201900095 VL - 19 IS - 1 SP - 1 EP - 2 PB - Wiley-VHC AN - OPUS4-49794 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bulling, Jannis T1 - Simulation von Wechselwirkungen von geführten Wellen mit Fehlstellen N2 - In der Zerstörungsfreien Prüfung und der Zustandsüberwachung sind geführte Wellen von großem Interesse, um Fehlstellen zu finden und zu charakterisieren. Die Interaktion der Wellen mit den Fehlstellen kann dabei aufgrund ihrer Komplexität häufig nicht analytisch beschrieben werden. Dies macht numerische Programme neben Experimenten unabdingbar. Aufgrund der kleinen Wellenlänge im Verhältnis zur Bauteilgröße ist jedoch eine effiziente Simulation noch immer Teil der aktiven Forschung. Um die Effizienz der Simulationsalgorithmen zu steigern, ist es möglich, analytische Annahmen in die Finite Elemente Methode (FEM) zu integrieren. Beispiele für solche Methoden sind die Scaled Boundary Finite Element Method als ein semi-analytisches Verfahren und eXtended Finite Element Method. Diese beiden Möglichkeiten erlauben es, die Wechselwirkungen effizient zu simulieren. In diesem Beitrag werden verschiedene Wechselwirkungen und Auswertungsmöglichkeiten von geführten Wellen mit Fehlstellen vorgestellt. Hierbei liegt der Fokus auf linearen und nicht-linearen Effekten. Zunächst wird auf Modenkonversion eingegangen und der Frage nachgegangen, ob diese ausreicht, um einen Riss zu charakterisieren. Diese Untersuchungen motivieren dann ein inverses Verfahren, mit dem einige Parameter eines simulierten Risses in einer Folge von Simulationen wieder rekonstruiert werden. Ein zweiter Teil beschäftigt sich mit nicht-linearen Risseffekten. Diese Risseffekte erzeugen im allgemeinen höhere harmonische Wellen. Hier werden Ergebnisse und Filtermethoden zur Auswertung vorgestellt. T2 - Doktorandenseminar "Geführte Wellen" CY - Delbrück, Germany DA - 21.10.2019 KW - Singular stress KW - Enriched finite element method KW - Scaled boundary finite element method; Stress intensity factors PY - 2019 AN - OPUS4-49798 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Strangfeld, Christoph A1 - Johann, Sergej A1 - Bartholmai, Matthias T1 - Smart RFID Sensors Embedded in Building Structures for Early Damage Detection and Long-Term Monitoring N2 - In civil engineering, many structures are made of reinforced concrete. Most Degradation processes relevant to this material, e.g., corrosion, are related to an increased level of material moisture. Therefore, moisture monitoring in reinforced concrete is regarded as a crucial method for structural health monitoring. In this study, passive radio frequency identification (RFID)-based sensors are embedded into the concrete. They are well suited for long-term operation over decades and are well protected against harsh environmental conditions. The energy supply and the data transfer of the humidity sensors are provided by RFID. The sensor casing materials are optimised to withstand the high alkaline environment in concrete, having pH values of more than 12. Membrane materials are also investigated to identify materials capable of enabling water vapour transport from the porous cement matrix to the embedded humidity sensor. By measuring the corresponding relative humidity with embedded passive RFID-based sensors, the cement hydration is monitored for 170 days. Moreover, long-term moisture monitoring is performed for more than 1000 days. The Experiments show that embedded passive RFID-based sensors are highly suitable for long-term structural health monitoring in civil engineering. KW - RFID based sensors KW - Embedded sensors KW - Corresponding relative humidity KW - Porous building materials KW - Reinforced concrete KW - Corrosion KW - Civil engineering PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-500831 DO - https://doi.org/10.3390/s19245514 VL - 19 IS - 24 SP - 1 EP - 18 PB - MDPI CY - Basel, Swiss AN - OPUS4-50083 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ratassepp, M. A1 - Rao, J. A1 - Yu, X. A1 - Fan, Z. A1 - Lugovtsova, Yevgeniya A1 - Prager, Jens T1 - Considering anisotropy in guided wave tomography for composite laminates N2 - Recently, various guided wave tomography algorithms have been developed to map structural changes from remote locations. The focus has been on structures made of isotropic materials and little work has been done on structures made of anisotropic materials. Primary complication to implement tomography in composite laminates is associated with the complex forward model to accurately simulate the 3-D guided wave propagation. In this study, we demonstrate that guided wave propagation can be approximated by an equivalent 2-D acoustic model. It is based on finite-difference discretization method in which the wave-field is parameterized by phase velocity and dimensionless anisotropic parameters. The reconstruction of defects is based on a full-waveform inversion algorithm and was implemented on the data obtained from finite element simulations. Results on a localized stiffness defects in composite plates with various layups demonstrate the attractiveness of the proposed methodology. T2 - International Symposium on Nondestructive Characterization of Materials (ISNCM 2019) CY - Portoroz, Slovenia DA - 17.09.2019 KW - Lamb waves KW - Ultrasonic Guided Waves KW - Multilayered structures PY - 2019 AN - OPUS4-50059 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Magkos, Sotirios T1 - Advanced algorithms for image reconstruction in Computed Tomography N2 - This PhD project is part of the Marie Skłodowska-Curie International Training Network MUMMERING. The overarching goal of MUMMERING is the creation of a research tool that exploits the wealth of 3D imaging modalities applied in materials engineering. The focus of this work is advanced reconstruction algorithms. The primary objective is the development and implementation of the DIRECTT algorithm. Due to restrictions introduced by the sample or the imaging setup during a measurement, it is not always possible to acquire data that fulfil the Nyquist sampling criterion. The DIRECTT algorithm is intended to produce reconstructions of superior quality for such cases of limited data sets, compared to those of other available algorithms, such as algebraic iterative ones. Although DIRECTT has been developed primarily for the reconstruction of volumes from data acquired by an X-ray Computed Tomography scanner, it can also be applied to the different modalities, such as laminography. The talk describes the reconstruction principle of DIRECTT. Furthermore, reconstructions of measured data are presented and compared to reconstructions produced by other established algorithms. T2 - Doktorandenseminar CY - BAM Berlin, Germany DA - 16.12.2019 KW - Computed Tomography KW - Reconstruction KW - DIRECTT PY - 2019 AN - OPUS4-50066 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gaal, Mate A1 - Hufschläger, Daniel A1 - Bente, Klaas T1 - Advances in air-coupled ultrasonic transducers for non-destructive testing N2 - Commercially available air-coupled transducers applied in non-destructive testing consist of a piezocomposite material and matching layers to reduce the impedance mismatch between the transducer and air. This contribution is an overview of innovative approaches using new piezoelectric materials and other physical principles to transmit and receive an ultrasonic pulse in air. Capacitive and piezoelectric micromachined ultrasonic transducers (CMUTs and PMUTs) produce high pressure levels, but they exhibit a very narrow bandwidth. Optical laser-based methods for transmitting and receiving ultrasound promise a higher bandwidth, but do not achieve the same sensitivity as conventional air-coupled transducers. Ferroelectrets are charged cellular polymers exhibiting piezoelectric properties, having a very small acoustic impedance well matched to air. Ferroelectret transducers achieve about the same bandwidth as the most broadband conventional air-coupled transducers, having a higher sensitivity. Thermoacoustic transducers use heat to initiate an acoustic wave, acting as transmitters in ultrasonic range. Thermoacoustic transducers enable excitation of extremely broadband pulses while producing high pressure levels, which opens new possibilities for advanced signal processing. The newest member of the family of air-coupled ultrasonic transmitters is the plasma-based transducer, using both the thermoacoustic effect and the movements of the ions (so called ionic wind) to create acoustic waves. T2 - International Congress on Ultrasonics CY - Bruges, Belgium DA - 03.09.2019 KW - Air-coupled transducers KW - Ferroelectret KW - Thermoacoustics KW - Plasma acoustics KW - Non-destructive testing PY - 2019 DO - https://doi.org/10.1121/2.0001072 SN - 1939-800X N1 - Geburtsname von Hufschläger, Daniel: Kotschate, D. - Birth name of Hufschläger, Daniel: Kotschate, D. VL - 38 IS - 1 SP - 030003-1 EP - 030003-7 PB - American Institute of Physics CY - Lancaster, Pa. AN - OPUS4-50103 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dominguez-Macaya, A. A1 - Gaal, Mate A1 - Gómez Álvarez-Arenas, T. E A1 - Aurrekoetxea, J. A1 - Iturrospe, A. T1 - Air-coupled ultrasonic testing with Lamb waves for straight and curved GFRP plates N2 - The use of composite materials has been steadily growing during the last decades, as well as the requirements on quality, mechanical properties and geometries of the parts. Some processes, like the 3D UV pultrusion process, manufacture parts that are long and thin, whilst having a varying curvature radius along the same part or even no curvature at all. Studying their mechanical properties along the main fiber direction, which is of foremost interest, is not an easy task nor efficient with most nondestructive methods. The use of air-coupled ultrasonics to evaluate the properties of composite materials has been widely proved by several authors, mainly using guided waves that provide information on the orthotropic properties of this kind of materials. Most of this work has focused on analyzing straight plate-like geometries, due to the simplicity to generate desired Lamb modes in the plate and analyze the behavior of guided waves inside the plate. In our contribution, the differences in the propagation of Lamb waves for straight and curved geometry glass fiber reinforced polymers (GFRP) have been analyzed. A GFRP test sample cured with UV light with one straight and one curved area has been evaluated. The responses of the generated Lamb wave modes for the straight and curved geometries have been compared, accounting for variations in the transducer characteristics, e.g. resonance behavior and focusing. T2 - International Congress on Ultrasonics CY - Bruges, Begium DA - 03.09.2019 KW - Air-coupled KW - Guided waves KW - Composites PY - 2019 DO - https://doi.org/10.1121/2.0001072 VL - 38 SP - 045005 AN - OPUS4-50104 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gaal, Mate T1 - Ferroelektret-Wandler für Luftultraschall N2 - Es wird ein Überblick über die Forschung an Ferroelektret-Wandlern für luftgekoppelte Ultraschallprüfung gegeben. T2 - Innovative ZFP mit bildgebender Ultraschallprüftechnik CY - Braunschweig, Germany DA - 29.11.2019 KW - Luftultraschall KW - Ferroelektret KW - Wandler PY - 2019 AN - OPUS4-50107 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Kowarik, Stefan A1 - Pithan, L. T1 - kowarik-labs/AI-reflectivity: v0.1 N2 - AI-reflectivity is a code based on artificial neural networks trained with simulated reflectivity data that quickly predicts film parameters from experimental X-ray reflectivity curves. This project has a common root with (ML-reflectivity)[https://github.com/schreiber-lab/ML-reflectivity] and evolved in parallel. Both are linked to the following publication: Fast Fitting of Reflectivity Data of Growing Thin Films Using Neural Networks A. Greco, V. Starostin, C. Karapanagiotis, A. Hinderhofer, A. Gerlach, L. Pithan, S. Liehr, F. Schreiber, S. Kowarik (2019). J. Appl. Cryst. For an online live demonstration using a pre-trained network have a look at github. KW - Artificial neural networks KW - X-ray reflectivity PY - 2019 DO - https://doi.org/10.5281/zenodo.3477583 PB - Zenodo CY - Geneva AN - OPUS4-51888 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bühling, Benjamin A1 - Strangfeld, Christoph A1 - Maack, Stefan T1 - Entwicklung eines luftgekoppelten Ultraschall-Echo-Prüfverfahrens mittels fluidischer Anregung N2 - In vielen technischen Bereichen werden Ultraschallverfahren zur zer-störungsfreien Werkstoffprüfung eingesetzt. Dabei wird ein Schallpuls von einem Prüfkopf in ein Prüfobjekt eingebracht. Der Puls kann unter anderem durch Membra-nen oder Piezoelemente erzeugt werden und wird in der Regel durch direkten Kontakt oder über ein Koppelmittel an das Objekt übertragen. Luftgekoppelter Ultraschall spielt in kommerziellen Anwendungen bisher eine untergeordnete Rolle, da die Dif-ferenz der akustischen Impedanzen von Luft und Festkörpern immense Verluste beim Übergang des Schallsignals hervorruft. In diesem Beitrag soll ein neuartiges Anregungsprinzip vorgestellt werden, mit dem ein Großteil dieser Verluste vermieden wird. Anstelle eines Festkörpers soll mit Hilfe einer fluidischen Düse Druckluft zur Signalerzeugung eingesetzt werden. In die-ser Düse wird eine selbsterhaltende Strömungsinstabilität erzeugt, die einen Schall-puls von bis zu 100 kHz hervorruft, sodass der Impedanzverlust in die Umgebungsluft entfällt. Da die charakteristische Frequenz eines fluidisch generierten Pulses maßgeb-lich von der Bauform der Düse und dem anliegenden Druck abhängt, lässt sich mittels einer geeigneten Strömungsregelung ein breiter Frequenzbereich zur Abtastung nut-zen. Die so emittierten Pulse werden auf das Prüfobjekt gerichtet und die reflektierten Signale mit einem Laservibrometer an der Oberfläche des Objekts im Echo-Verfahren abgetastet. Von drei signalmindernden Materialübergängen bei gewöhnlichem luftge-koppeltem Ultraschall bleibt in dem hier vorgeschlagenen Messystem lediglich die Grenzfläche von Luft zu Prüfkörper, sodass eine höhere Signalausbeute als bisher er-wartet werden kann. T2 - DACH-Jahrestagung 2019 CY - Friedrichshafen, Germany DA - 27.05.2019 KW - Ultraschall KW - Ultrasound KW - Air-coupled KW - Luftgekoppelt KW - Fluidic oscillator KW - Fluidischer Oszillator KW - Laser-Doppler-Vibrometer KW - Refraktovibrometrie KW - Refracto-vibrometry KW - NDT KW - ZfP PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-481207 VL - 2019 SP - 1 EP - 8 PB - DGZfP Deutsche Gesellschaft für Zerstörungsfreie Prüfung AN - OPUS4-48120 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strangfeld, Christoph A1 - Knopp, Florian A1 - Mielentz, Frank A1 - Bernstein, Thomas T1 - Ultraschall-Messsystem für die Langzeitüberwachung von Betonkonstruktionen N2 - Ultraschallmessverfahren werden seit Langem erfolgreich für Prüfaufgaben im Bauwesen eingesetzt. Die dauerhafte Überwachung und frühzeitige Erkennung von Schäden an komplexen Neubauten und alternder Infrastruktur kann mittels Ultraschall-Transmissionsmessungen und speziellen Auswertemethoden, wie z. B. Korrelationverfahren und Codawelleninterferometrie, realisiert werden. Für die Dauerüberwachung wurde ein kompaktes System entwickelt, das Ultraschall-Messdaten erfassen und ins Internet auf einen FTP-Server übertragen kann. Es können hierbei alle angeschlossenen Prüfköpfe für jede Messung wahlweise als Sender oder Empfänger geschaltet werden. Es wurden Vorverstärker entwickelt, bei denen die Versorgung mit Strom über die Messleitung erfolgt. Dadurch können die Verstärker nahe am Prüfkopf positioniert werden. Durch Änderungen in den Ultraschall-Signalen können Schädigungen des Bauteils, wie z.B. Risse, in Echtzeit erkannt werden. T2 - DGZfP DACH-Jahrestagung CY - Friedrichshafen, Germany DA - 27.05.2019 KW - Ultraschall KW - Monitoring KW - Codawelleninterferometrie KW - Eingebettete Sensorik PY - 2019 AN - OPUS4-48144 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kruschwitz, Sabine A1 - Munsch, Sarah Mandy A1 - Strangfeld, Christoph T1 - Ermittlung des Flüssigwasseranteils an Kalziumsilikatplatten bei Teilsättigung mittels NMR N2 - Feuchte, insbesondere in Form von Flüssigwasser, stellt in Baustoffen ein hohes Schadenspotential dar. Um mit zerstörungsfreier Prüfung mögliche Risikostellen zu lokalisieren und Präventionsmaßnahmen zu ergreifen, sind Kenntnisse über das Porengefüge und Feuchtetransportmechanismen im Baustoff erforderlich. Eine wesentliche Problematik besteht derzeit in der Erfassung und Quantifizierung von Feuchteverteilungen bei Teilsättigung. Wir verfolgen derzeit einen Ansatz, mittels Nuklear Magnetischer Resonanz (NMR) in Korrelation mit relativen Luftfeuchtmessungen den Flüssigwasseranteil bei Teilsättigung zu ermitteln. Mit Protonen-NMR lassen sich Relaxationszeiten von Wasserstoffprotonen in Abhängigkeit von ihrer Bindungsart und ihrer Umgebung - z. B. Porenstruktur und -größe - erfassen. Allerdings lässt sich bei Materialien mit sehr breiten Porengrößenverteilungen nicht klar differenzieren, ob kurze Relaxationszeiten durch größere teilgesättigte oder kleinere vollgesättigte Poren verursacht werden. Für die Korrelation mit der relativen Luftfeuchte im Baustoff erfolgt zunächst eine künstliche Regulierung im Klimaschrank. Durch einen neuentwickelten Ansatz von Hillerborg lassen sich dann bei jeder Luftfeuchte die adsorbierten Wasserschichtdicken und der Porensättigungsgrad für die vorhandenen Porengrößen berechnen. Mithilfe des berechneten Porensättigungsgrades lässt sich eine genauere Analyse der zeitlichen Entwicklung von Relaxationszeitenverteilungen (insbesondere bei Trocknungs- und Aufsättigungsprozessen) vornehmen. Somit sollen erstmals Aussagen zu kürzeren Relaxationszeiten bei teilgesättigten Porensystemen, die beispielsweise auch eine multimodale Porengrößenverteilung aufweisen, getroffen werden können. In dieser Arbeit wird die Kombination aus NMR und der relativen Luftfeuchte an sehr porösen Dämmplatten aus Kalziumsilikat, die zur Wärmedämmung sowie der Entgegenwirkung von Schimmelbildung eingesetzt werden, angewendet. Untersucht werden 28 Proben à 6 Gruppen, die von unterschiedlichen Herstellern stammen bzw. unterschiedlich hergestellt wurden. T2 - DACH-Jahrestagung CY - Friedrichshafen, Germany DA - 27.05.2019 KW - NMR KW - Kalziumsilikat KW - Flüssigwasser KW - Hygrometrie PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-481681 UR - http://www.ndt.net/?id=24594 N1 - Geburtsname von Munsch, Sarah Mandy: Nagel, S. M. - Birth name of Munsch, Sarah Mandy: Nagel, S. M. AN - OPUS4-48168 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kowarik, Stefan A1 - Bogula, A1 - Boitano, A1 - Carla, A1 - Pithan, A1 - Schafer, A1 - Wilming, A1 - Zykov, A1 - Pithan, T1 - A novel 3D printed radial collimator for x-ray diffraction N2 - We demonstrate the use of a 3D printed radial collimator in X-ray powder diffraction and surface sensitive grazing incidence X-ray diffraction. We find a significant improvement in the overall Signal to background ratio of up to 100 and a suppression of more than a factor 3⋅10⁵ for undesirable Bragg reflections generated by the X-ray “transparent” windows of the sample environment. The background reduction and the removal of the high intensity signals from the windows, which limit the detector’s dynamic range, enable significantly higher sensitivity in experiments within sample environments such as vacuum chambers and gas- or liquid-cells. Details of the additively manufactured steel collimator geometry, alignment strategies using X-ray fluorescence, and data analysis are also briefly discussed. The flexibility and affordability of 3D prints enable designs optimized for specific detectors and sample environments, without compromising the degrees of freedom of the diffractometer. KW - 3D printing PY - 2019 DO - https://doi.org/10.1063/1.5063520 SN - 0034-6748 VL - 90 IS - 3 SP - 035102, 1 EP - 8 PB - AIP AN - OPUS4-48171 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kruschwitz, Sabine A1 - Klewe, Tim A1 - Strangfeld, Christoph A1 - Ritzer, T. T1 - Kombination von Radar und Neutronensonde zur Bestimmung der Massenfeuchte von Estrichen N2 - Leitungswasserschäden nahmen im Jahr 2016 mit rund 2,6 Milliarden Euro den größten Posten bei Gebäudeversicherungen ein. Die Bestimmung und Lokalisierung des Schadensausmaßes ist dabei ein erster wichtiger Schritt, um die erforderlichen Sanierungsarbeiten abschätzen und effizient vornehmen zu können. Hierfür sind Radar und Neutronensonden bereits etablierte Verfahren. Für verlässliche Aussagen zum quantitativen Feuchtegehalt eines Baustoffes werden jedoch zerstörende Sondierungsbohrungen zur Kalibrierung der aufgenommenen Daten benötigt. Dieser hohe zeitliche und finanzielle Aufwand soll zukünftig durch den parallelen Einsatz der genannten Messverfahren verhindert werden. In der durchgeführten Studie wurden Estrichprobekörper auf Zement- und Anhydritbasis mit variablen Dicken und Festigkeiten hergestellt und deren Austrocknung mit Radar und Neutronensonde über einen Zeitraum von 90 Tagen beobachtet. Als Referenzverfahren zur Ermittlung des Feuchteverlaufs dienten die gravimetrische Darr- und chemische Calcium-Carbid-Methode, welche an kleineren Schwesterproben der gleichen Charge angewendet wurden. Kontinuierliche Wägungen der größeren Probekörper gaben hierbei Aufschluss über den durch Austrocknung schwindende Wasseranteil. Aus dem aufgenommen Radardatensatz konnten anschließend markante Signalmerkmale im Zeit- und Frequenzbereich extrahiert und deren Zusammenhang zum Feuchtegehalt der Estrichtypen untersucht werden. Hierbei wurden gängige Methoden aus der Literatur zur Feuchtemessung mit Radar angewandt, wobei die Kombination dieser und das Hinzuziehen der Neutronensonde mittels Datenfusion zu einem höheren Informationsgehalt beiträgt. Somit kann eine zerstörungsfreie Quantifizierung des Feuchteschadens an schwimmenden Fußbodenaufbauten vorgenommen werden T2 - DACH-Jahrestagung DGZfP 2019 CY - Friedrichshafen, Germany DA - 27.05.2019 KW - Radar KW - Feuchte KW - Multiple Lineare Regression KW - Neutronensonde KW - Datenfusion PY - 2019 AN - OPUS4-48152 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kruschwitz, Sabine A1 - Klewe, Tim A1 - Strangfeld, Christoph A1 - Ritzer, T. T1 - Kombination von Radar und Neutronensonde zur Bestimmung der Massenfeuchte von Estrichen N2 - Leitungswasserschäden nahmen im Jahr 2016 mit rund 2,6 Milliarden Euro den größten Posten bei Gebäudeversicherungen ein. Die Bestimmung und Lokalisierung des Schadensausmaßes ist dabei ein erster wichtiger Schritt, um die erforderlichen Sanierungsarbeiten abschätzen und effizient vornehmen zu können. Hierfür sind Radar und Neutronensonden bereits etablierte Verfahren. Für verlässliche Aussagen zum quantitativen Feuchtegehalt eines Baustoffes werden jedoch zerstörende Sondierungsbohrungen zur Kalibrierung der aufgenommenen Daten benötigt. Dieser hohe zeitliche und finanzielle Aufwand soll zukünftig durch den parallelen Einsatz der genannten Messverfahren verhindert werden. In der durchgeführten Studie wurden Estrichprobekörper auf Zement- und Anhydritbasis mit variablen Dicken und Festigkeiten hergestellt und deren Austrocknung mit Radar und Neutronensonde über einen Zeitraum von 90 Tagen beobachtet. Als Referenzverfahren zur Ermittlung des Feuchteverlaufs dienten die gravimetrische Darr- und chemische Calcium-Carbid-Methode, welche an kleineren Schwesterproben der gleichen Charge angewendet wurden. Kontinuierliche Wägungen der größeren Probekörper gaben hierbei Aufschluss über den durch Austrocknung schwindende Wasseranteil. Aus dem aufgenommen Radardatensatz konnten anschließend markante Signalmerkmale im Zeit- und Frequenzbereich extrahiert und deren Zusammenhang zum Feuchtegehalt der Estrichtypen untersucht werden. Hierbei wurden gängige Methoden aus der Literatur zur Feuchtemessung mit Radar angewandt, wobei die Kombination dieser und das Hinzuziehen der Neutronensonde mittels Datenfusion zu einem höheren Informationsgehalt beiträgt. Somit kann eine zerstörungsfreie Quantifizierung des Feuchteschadens an schwimmenden Fußbodenaufbauten vorgenommen werden T2 - DACH-Jahrestagung DGZfP 2019 CY - Friedrichshafen, Germany DA - 27.05.2019 KW - Radar KW - Feuchte KW - Neutronensonde KW - Datenfusion PY - 2019 AN - OPUS4-48153 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Küttenbaum, Stefan A1 - Maack, Stefan A1 - Braml, T. A1 - Taffe, A. A1 - Haslbeck, M. T1 - Bewertung von Bestandsbauwerken mit gemessenen Daten. Teil 1: Konzept, Messungen und Leistungsfähigkeit der ZfP‐Verfahren N2 - Gegenüber dem Neubauentwurf können bei der Bewertung von bestehender Bausubstanz Sicherheitsreserven genutzt werden, da Unsicherheiten, die beim Bau auftreten können, besser bekannt oder nicht mehr vorhanden sind. Können solche Unsicherheiten genauer bewertet werden, z. B. durch die Feststellung der genauen Lage der Spannglieder bei einer Spannbetonbrücke, so können Sicherheitsbeiwerte reduziert werden, ohne dass es dabei zu Auswirkungen auf das normativ festgelegte Zuverlässigkeitsniveau kommt. Mittlerweile sind Prüfmethoden an Bauwerken wirtschaftlich einsetzbar und auch so leistungsfähig, dass die für die Tragfähigkeit und Gebrauchstauglichkeit wesentlichen Parameter identifiziert werden können. Ein wesentlicher Punkt ist hierbei die Integration derartiger Messergebnisse in Rechenmodelle, die für die Nachrechnung des Bauwerks verwendet werden. Dies können sowohl semiprobabilistische Rechenmodelle als auch vollprobabilistische Modelle sein. Bei semiprobabilistischen Methoden können aus den Messergebnissen Teilsicherheitsbeiwerte berechnet und abgeleitet werden, die dann in den bekannten Nachweisformaten gemäß den Eurocodes und der Nachrechnungsrichtlinie berücksichtigt werden. Bei vollprobabilistischen Nachweisen können die Messdaten in Form von Verteilungsdichtefunktionen mit gemessenen Variationskoeffizienten direkt in das Rechenmodell eingehen. In einer dreiteiligen Aufsatzreihe werden die Messverfahren und die Nutzung der Ergebnisse bei der Nachrechnung vorgestellt. Der vorliegende Teil 1 zeigt die Möglichkeiten des Einsatzes von zerstörungsfreien Prüfverfahren und bewertet deren Leistungsfähigkeit. Messen heißt wissen. Dieses Wissen spiegelt die Realität wider und soll den Tragwerksplaner bei der Entscheidungsfindung über die Sicherheit und Zuverlässigkeit von Bestandsbauwerken unterstützen. KW - Nachrechnung KW - Zerstörungsfreie Prüfung KW - Messunsicherheit KW - Brücken KW - Beton PY - 2019 DO - https://doi.org/10.1002/best.201900002 SN - 1437-1006 VL - 114 IS - 6 SP - 370 EP - 382 PB - Ernst & Sohn Verlag für Architektur und technische Wissenschaften GmbH & Co. KG CY - Berlin AN - OPUS4-48156 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Heckel, Thomas T1 - Fachbereich 8.4 - Akustische Verfahren N2 - Die akustischen Verfahren der zerstörungsfreien Prüfung werden vorgestellt, die im Fachbereich 8.4 der BAM entwickelt werden. T2 - DGZfP Sitzung des Fachausschusses Luftfahrt CY - Berlin, Germany DA - 18.04.2019 KW - Ultraschall KW - Luftultraschall KW - Tauchtechnik KW - Geführte Wellen PY - 2019 AN - OPUS4-48069 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Casperson, Ralf A1 - Pohl, Rainer A1 - Lohde, Sebastian A1 - Aydoğdu, M. T1 - Zerstörungsfreie Prüfung von Composite-Druckgefäßen mit konventioneller und hochfrequenter Wirbelstromtechnik N2 - Composite-Druckgefäße für den Gefahrguttransport sowie für Wasserstoff- und Erdgasfahrzeuge bestehen aus einem lasttragenden Composite und einer gasdichten, metallischen oder polymeren Barriereschicht (Liner). Zur Untersuchung des Alterungsverhaltens solcher Composite-Druckgefäße wurde in der BAM das interdisziplinäre Themenfeldprojekt COD-AGE durchgeführt. Ziel des Projektes war die Entwicklung von Methoden und Modellen zur Beschreibung und Bestimmung des Alterungsverhaltens von Carbonfaser-Compositen am Beispiel von Druckgefäßen, um eine bessere Vorhersage der Alterung und der sicheren Gebrauchsdauer zu ermöglichen. Ein Schwerpunkt in diesem Projekt war die Bereitstellung geeigneter ZfP-Methoden. Dabei ging es sowohl um versuchsbegleitende Prüfungen, als auch um die mögliche Entwicklung von Prüfeinrichtungen für den späteren praktischen Gebrauch. In dem Vortrag werden Prüfergebnisse der alterungsbegleitenden Wirbelstromprüfung an Composite-Druckgefäßen vorgestellt. In Alterungsversuchen wurden Druckgefäße aus einem ca. 4 mm dicken Aluminiumliner und ca. 8 mm dicker CFK-Ummantelung untersucht. Typisches Einsatzgebiet solcher Druckgefäße sind Atemschutzgeräte der Feuerwehr. Die Druckgefäße wurden sowohl mit konventioneller Wirbelstromtechnik von außen und von innen als auch mit hochfrequenter Wirbelstromtechnik von außen geprüft. Es konnten sowohl Beschädigungen des metallischen Liners, als auch Strukturen des CFK-Geflechts nachgewiesen werden. Eine besondere mechanische Herausforderung bestand in der Prüfung der Innenseite der Liner, da hier eine zylindrische Fläche mit einem Innendurchmesser von 150 mm durch einen Zugang von nur 15 mm Durchmesser geprüft werden muss. T2 - DACH-Jahrestagung CY - Friedrichshafen, Germany DA - 26.05.2019 KW - Wirbelstromprüfung KW - COD-AGE KW - Composite-Druckgefäß KW - CFK PY - 2019 AN - OPUS4-48123 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Casperson, Ralf A1 - Pohl, Rainer A1 - Lohde, Sebastian A1 - Aydoğdu, M. T1 - Zerstörungsfreie Prüfung von Composite-Druckgefäßen mit konventioneller und hochfrequenter Wirbelstromtechnik N2 - Composite-Druckgefäße für den Gefahrguttransport sowie für Wasserstoff- und Erdgasfahrzeuge bestehen aus einem lasttragenden Composite und einer gasdichten, metallischen oder polymeren Barriereschicht (Liner). Zur Untersuchung des Alterungsverhaltens solcher Composite-Druckgefäße wurde in der BAM das interdisziplinäre Themenfeldprojekt COD-AGE durchgeführt. Ziel des Projektes war die Entwicklung von Methoden und Modellen zur Beschreibung und Bestimmung des Alterungsverhaltens von Carbonfaser-Compositen am Beispiel von Druckgefäßen, um eine bessere Vorhersage der Alterung und der sicheren Gebrauchsdauer zu ermöglichen. Ein Schwerpunkt in diesem Projekt war die Bereitstellung geeigneter ZfP-Methoden. Dabei ging es sowohl um versuchsbegleitende Prüfungen, als auch um die mögliche Entwicklung von Prüfeinrichtungen für den späteren praktischen Gebrauch. In dem Vortrag werden Prüfergebnisse der alterungsbegleitenden Wirbelstromprüfung an Composite-Druckgefäßen vorgestellt. In Alterungsversuchen wurden Druckgefäße aus einem ca. 4 mm dicken Aluminiumliner und ca. 8 mm dicker CFK-Ummantelung untersucht. Typisches Einsatzgebiet solcher Druckgefäße sind Atemschutzgeräte der Feuerwehr. Die Druckgefäße wurden sowohl mit konventioneller Wirbelstromtechnik von außen und von innen als auch mit hochfrequenter Wirbelstromtechnik von außen geprüft. Es konnten sowohl Beschädigungen des metallischen Liners, als auch Strukturen des CFK-Geflechts nachgewiesen werden. Eine besondere mechanische Herausforderung bestand in der Prüfung der Innenseite der Liner, da hier eine zylindrische Fläche mit einem Innendurchmesser von 150 mm durch einen Zugang von nur 15 mm Durchmesser geprüft werden muss. T2 - DACH-Jahrestagung CY - Friedrichshafen, Germany DA - 26.05.2019 KW - Wirbelstromprüfung KW - COD-AGE KW - Composite-Druckgefäß KW - CFK PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-481243 SN - 978-3-947971-02-2 VL - 171 SP - 1 EP - 8 PB - Deutsche Gesellschaft für Zerstörungsfreie Prüfung (DGZfP) CY - Berlin AN - OPUS4-48124 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CHAP A1 - Oesch, Tyler A1 - Stelzner, Ludwig A1 - Weise, Frank ED - Herrmann, H. ED - Schnell, J. T1 - Non-destructive evaluation of the contribution of polymer-fibre orientation and distribution characteristics to concrete performance during fire N2 - Although concrete itself is not a combustible material, concrete mixtures with high density, such has high-performance concretes (HPCs), are susceptible to significant damage during fires due to explosive spalling. Past research has shown that the inclusion of polymer fibres in high density concrete can significantly mitigate this fire damage. The exact mechanisms causing this increased spalling resistance are not yet fully under-stood, but it is thought that the fibres facilitate moisture transport during fire exposure, which in turn contributes to relief of internal stresses in the spalling-susceptible region. In this study, X-ray Computed Tomography (CT) was applied to observe the interaction between polymer fibres and cracking during thermal exposure. For this purpose, two concrete samples containing different polymer fibre types were subjected to incremental application of a defined thermal exposure. CT images were acquired before and after each thermal exposure and powerful image processing tools were used to segment the various material components. This enabled a detailed analysis of crack formation and propagation as well as the visualization and quantification of polymer fibre characteristics within the concrete. The results demonstrated that the orientation of both fibres and cracks in polymer-fibre reinforced concrete tend to be anisotropic. The results also indicated that crack geometry characteristics may be correlated with fibre orientation, with cracks tending to run parallel to fibre beds. Clear quantitative relationships were also observed between heating and increasing cracking levels, expressed in terms of both crack surface area and crack volume. KW - X-ray Computed Tomography (CT) KW - Polypropylene Fibres KW - Fire Performance KW - Fibre-Reinforced Concrete (FRC) KW - Fibre Orientation Analysis PY - 2019 SN - 978-3-030-00868-0 DO - https://doi.org/10.1007/978-3-030-00868-0 SP - 51 EP - 73 PB - Springer Nature Switzerland AG AN - OPUS4-47206 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Thiel, Erik A1 - Ziegler, Mathias A1 - Studemund, Taarna T1 - Localization of subsurface defects in uncoated aluminum with structured heating using high-power VCSEL laser arrays N2 - We report on photothermal detection of subsurface defects by coherent superposition of thermal wave fields. This is made possible by structured heating using high-power VCSEL laser arrays whose individual emitter groups can be arbitrarily controlled. In order to locate the defects, we have developed a scanning method based on the continuous wavelet transformation with complex Morlet wavelet using the destructive interference effect of thermal waves. This approach can also be used for thermally very fast and highly reflective materials such as uncoated aluminum. We show that subsurface defects at an aspect ratio of defect width to defect depth down to 1/3 are still detectable in this material. KW - Thermography KW - Heat diffusion KW - Laser thermography KW - Structured heating KW - NDT KW - Subsurface defects KW - Thermal wave KW - VCSEL KW - Wavelet transformation PY - 2019 DO - https://doi.org/10.1007/s10765-018-2478-9 SN - 1572-9567 SN - 0195-928X VL - 40 IS - 2 SP - 17, 1 EP - 13 PB - Springer Science+Business Media, LLC, part of Springer Nature 2019 AN - OPUS4-47208 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gaal, Mate A1 - Kotschate, Daniel A1 - Bartusch, Jürgen A1 - Hansen, L. A1 - Kersten, H. T1 - Neue Entwicklungen im Bereich der luftgekoppelten Ultraschallprüfung N2 - Es wird über Ferroelektret-Wandler, thermoakustische Wandler und Plasma-Wandler für luftgekoppelte Ultraschallprüfung berichtet. T2 - Sitzung des Arbeitskreises Berlin der DGZfP CY - Berlin, Germany DA - 12.02.2019 KW - Luftultraschall KW - Ferroelektret KW - Thermoakustik KW - Plasma PY - 2019 AN - OPUS4-47375 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gaal, Mate A1 - Heckel, Thomas T1 - Ultraschallprüfung in der BAM (Fachbereich 8.4 - Zerstörungsfreie Prüfung - Akustische und elektromagnetische Verfahren) N2 - Vorstellung des Fachbereichs 8.4 mit dem Schwerpunkt Ultraschallprüfung. T2 - Sitzung des DFG-Schwerpunktprogramms Zyklische Schädigungsprozesse in Hochleistungsbetonen im Experimental-Virtual-Lab2020 CY - Berlin, Germany DA - 6.2.2019 KW - Luftultraschall KW - Ultraschall KW - Phased Array KW - Simulation KW - Wirbelstrom KW - Magnetfeldsensoren PY - 2019 AN - OPUS4-47376 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, David A1 - Ou, D. A1 - Ghafafian, Carineh A1 - Zscherpel, Uwe A1 - Trappe, Volker T1 - Wind turbine rotor blade testing by dual-energy laminography N2 - Modern wind turbine rotor blades consist of sandwich shell segments made from glass fiber reinforced polymers. During manufacturing, defects can arise which could lead to failure of the whole component under dynamic mechanical and thermal loads. Hence during operation defects can arise which, if detected, can be repaired locally and in-situ by applying repair patches instead of taking the whole rotor blade down and repair it remotely. This method is much more time and cost effective, since the shut-down time of the energy converter is limited to a minimum. These repair patches can, however, also lead to new defects if not applied optimally. Therefore, it is necessary to control the quality of the repair patches to ensure the best possible restoration of structural integrity of the component. As a rotor blade is an object with a large aspect ratio, X-ray laminography is predestined to provide 3D information of the objective volume. To enhance the amount of information gained from laminographic reconstruction, we use in this study a photon counting and energy discriminating X-ray detector and apply a material decomposition algorithm to the data. By inherently separating the incident spectra within the detection process into two distinct energy bins, the basis material decomposition can provide material resolved images. Choosing glass and epoxy resin as basis materials and numerically solving the inverse dual-energy equation system, the reconstructed laminographic datasets contain highly valuable information about the distribution of the basis materials within the structure. Furthermore, cross- artifacts arising from the limited angle of the projection data can be reduced by this method which allows to investigate structures that were hidden underneath the artefacts. T2 - International Symposium on Digital Industrial Radiology and Computed Tomography – DIR2019 CY - Fürth, Germany DA - 02.07.2019 KW - Laminography KW - Wind energy KW - Fiber reinforced polymer KW - Photon counting detector KW - Repair patch PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-484380 UR - https://www.dir2019.com/portals/dir2019/bb/Tu.3.A.1.pdf SN - 978-947971-06-0 SP - 1 EP - 13 AN - OPUS4-48438 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, David A1 - Ou, D. A1 - Ghafafian, Carineh A1 - Zscherpel, Uwe A1 - Trappe, Volker T1 - Wind turbine rotor blade testing by dual-energy laminography N2 - Modern wind turbine rotor blades consist of sandwich shell segments made from glass fiber reinforced polymers. During manufacturing, defects can arise which could lead to failure of the whole component under dynamic mechanical and thermal loads. Hence during operation defects can arise which, if detected, can be repaired locally and in-situ by applying repair patches instead of taking the whole rotor blade down and repair it remotely. This method is much more time and cost effective, since the shut-down time of the energy converter is limited to a minimum. These repair patches can, however, also lead to new defects if not applied optimally. Therefore, it is necessary to control the quality of the repair patches to ensure the best possible restoration of structural integrity of the component. As a rotor blade is an object with a large aspect ratio, X-ray laminography is predestined to provide 3D information of the objective volume. To enhance the amount of information gained from laminographic reconstruction, we use in this study a photon counting and energy discriminating X-ray detector and apply a material decomposition algorithm to the data. By inherently separating the incident spectra within the detection process into two distinct energy bins, the basis material decomposition can provide material resolved images. Choosing glass and epoxy resin as basis materials and numerically solving the inverse dual-energy equation system, the reconstructed laminographic datasets contain highly valuable information about the distribution of the basis materials within the structure. Furthermore, cross- artifacts arising from the limited angle of the projection data can be reduced by this method which allows to investigate structures that were hidden underneath the artefacts. T2 - 1st International Symposium on Photon Counting Technologies & Applications CY - München, Germany DA - 05.07.2019 KW - Laminography KW - Wind energy KW - Fiber reinforced polymer KW - Photon counting detector KW - Dual-energy PY - 2019 AN - OPUS4-48440 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ewert, U. A1 - Jaenisch, Gerd-Rüdiger A1 - Deresch, A. A1 - Bircher, B. A. A1 - Meli, F. T1 - New concepts for the measurement of focal spot parameters of nano- and microfocus X-ray tubes N2 - Accurate measurement of focal spot sizes of X-ray tubes, betatrons and linear accelerators is still an open problem. Several standards are currently active, which provide different results depending on the focal spot shape. CEN published the standard series EN 12543 (five parts) in 1999, which describes the measurement of focal spot sizes of X-ray tubes for NDT applications. The measurement procedure and its tolerances deviate from the measurement standards for medical X-ray tubes, e.g. EN 60336:2006 / IEC 60336:2005. EN 12543 describes different measurement methods for X-ray tubes with focal spots in several size ranges, defined as macrofocus, minifocus and microfocus. CEN TC 138 WG 1 und ASTM E 07.01 are revising (CEN) or have just revised (ASTM) the standards for focal spot size measurements, basing them on pin hole or edge measurements only. Slit cameras are applied for medical tube evaluation only. Tomographic methods for focal spot size shape reconstruction were proposed and will be discussed, but have not yet been used for standardization. The currently available standards cover the range of spot sizes from 5 µm up to several millimetres. During the last years, more and more nanofocus tubes have been developed for high-resolution applications and microscopy. Manufacturers and users apply different methods for measurement of nanofocus spot sizes and image resolution, which differ by a factor of up to two. These well-known methods and new alternative methods for the measurement of nanofocus spots (size and shape) will be evaluated and improved in the EMPIR project “NanoXSpot” in order to develop a related measurement standard. T2 - International Symposium on Digital Industrial Radiology and Computed Tomography CY - Fürth, Germany DA - 02.07.2019 KW - X-Ray tube KW - Focal spot measurement KW - Standadization PY - 2019 AN - OPUS4-48442 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Zimmek, David A1 - Bartelmeß, Jürgen A1 - Strangfeld, Christoph A1 - Bartholmai, Matthias A1 - Schäferling, Michael T1 - Entwicklung von Fluoreszenzspektroskopischer Sensorik zur pH-Wert Bestimmung in Baustoffen N2 - Das Projekt befasst sich mit einem neuen Ansatz, den pH-Wert im Beton zu bestimmen. Der pH-Wert ist vor allem für Stahlbeton-Bauwerke von Bedeutung, da dieser maßgeblich die Korrosion des Stahls beeinflusst. Im frischen Beton liegt der pH-Wert im basischen Bereich. Der Stahl ist in diesem Bereich passiviert, also vor schädlicher Korrosion geschützt. Durch die sogenannte Karbonatisierung sinkt der pH-Wert und die Korrosionswahrscheinlichkeit steigt deutlich an. Die Stabilität von Bauwerken in denen Stahlbeton verbaut ist, wird durch diese Korrosion langfristig beeinträchtigt. Allein in deutscher Infrastruktur rechnet man mit circa 5 Milliarden Euro Schaden jährlich. Die entwickelte Methode verwendet Sonden, welche die Korrosion Monitoren sollen. Im Sondeninneren befindet sich eine Schicht pH-Indikator (Thymolblau) und eine Schicht mit Quantenpunkten. Die Quantenpunkte fluoreszieren, nach Anregung durch zum Beispiel einen Laser, bei circa 440 nm (blau) beziehungsweise 610 nm (gelb-orange). Das Thymolblau ist im basischen Milieu (pH > 9,6) blau, im neutralen Milieu (um pH 7) gelb-orange. Der Indikator wirkt wie ein Farbfilter und lässt, je nach pH-Wert, unterschiedliche Wellenlängen zur Glasfaser durch. Aus der gemessenen Intensität bei 440 nm und 610 nm kann ein Verhältnis ermittelt werden. Dieses Verhältnis lässt erkennen, welchen pH-Wert das Milieu besitzt, in dem sich die Sonde befindet. Die entwickelte Methodik ist zerstörungsfrei, das heißt kein Material muss aus den Bauwerken entnommen werden. Vielmehr sollen die Sonden beim Betonieren in das Bauwerk eingebettet werden. Über Glasfasern können die Sonden jederzeit angesprochen werden. Dies ermöglicht permanentes pH-Monitoring, was die Früherkennung von Korrosionsgefahr verbessert und die Sanierungskosten verringert. T2 - Simulation in den Umwelt- und Geowissenschaften 2019 CY - Kassel, Germany DA - 08.05.2019 KW - pH-Monitoring KW - Korrosion KW - Stahlbeton KW - Quantenpunkte KW - Thymolblau PY - 2019 AN - OPUS4-47993 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Millar, Steven A1 - Kruschwitz, Sabine A1 - Wilsch, Gerd T1 - Determination of total chloride content in cement pastes with laser-induced breakdown spectroscopy (LIBS) N2 - The presented work discusses the accuracy of Laser Induced Breakdown Spectroscopy (LIBS) in determining the total chloride content in cement pastes. LIBS as an emission spectroscopy method is used to detect simultaneously several elements present in cement-based materials. By scanning surfaces the variability in the spatial distribution of elements can be visualised. However, for a quantification of the results, studies are necessary to characterise possible influences due to the wide variation of the chemical compositions in which cement can occur. It is shown how the calibration can be done, how the calibration samples were produced, and which statistical parameters are necessary to describe the precision of the regression. The performance of LIBS is estimated by detecting chloride in validation samples. Therefore, 55 samples and 7 ets with changing mix ompositions were produced. The presented study deals with possible influences of different mix compositions, ncluding different cations of chloride, varying w/c-ratios and the artial replacement of Portland cement with last furnace slag (50% BFS) and limestone (30% LS). Comparing the LIBS results with otentiometric titration, n accuracy of±0.05 wt%/total has been determined. KW - Spectroscopy KW - LIBS KW - Chloride KW - Quantification KW - Cement PY - 2019 DO - https://doi.org/10.1016/j.cemconres.2018.12.001 SN - 0008-8846 VL - 117 IS - March SP - 16 EP - 22 PB - Elsevier CY - Amsterdam AN - OPUS4-47059 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Völker, Tobias A1 - Millar, Steven A1 - Strangfeld, Christoph A1 - Wilsch, Gerd T1 - Classification of cement pastes with laser-induced breakdown spectroscopy N2 - In civil engineering, the investigation of existing infrastructure is of major importance for maintaining and ensuring stability of the structures. To ensure durability, uniform regulations and standards apply e.g. the European standard EN 206-1. In some countries, the EN-standard is supplemented by additional standards, as in Germany with DIN 1045-2. Here, specific application rules are described, e.g. for the cement type, to ensure the resistant to different exposures. Therefore, the knowledge of the materials originally used is important in assessing the condition of existing concrete structure. Unfortunately, these are often unknown and must be determined retrospectively. Therefore, we present the application of the laser-induced breakdown spectroscopy to distinguish between different types of cement. Spectral information’s are used to build a classification model. First, the accuracy of the classification is analyzed on ten pure laboratory cement samples. To investigate possible sources of error, the model was then applied to cement samples with different moisture content. The study shows that LIBS is a promising tool for distinguishing between cement types. For further industrial application, however, factors influencing the LIBS signal must be included to ensure a robust model. T2 - 10th Euro-Mediterranean Symposium on Laser-Induced Breakdown Spectroscopy CY - Brno, Czech Republic DA - 08.09.2019 KW - Spectroscopy KW - LIBS KW - Cement KW - Classification PY - 2019 AN - OPUS4-49253 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strangfeld, Christoph A1 - Munsch, Sarah Mandy A1 - Kruschwitz, Sabine T1 - Water content in construction materials N2 - Discussion of material moisture and moisture transport in liquid and vapour phase. Prediction of the pore saturation in partially saturated pores in building materials. T2 - 5. Herbstschule Competence Center for Material Moisture CY - Ettlingen, Germany DA - 08.10.2019 KW - Material moisture KW - Building materials KW - Embedded sensors KW - Partially saturated pores PY - 2019 N1 - Geburtsname von Munsch, Sarah Mandy: Nagel, S. M. - Birth name of Munsch, Sarah Mandy: Nagel, S. M. AN - OPUS4-49260 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Strangfeld, Christoph T1 - Correlation between the electric impedance and the water layer thickness in partially saturated screed samples N2 - Discussion of material moisture in liquid and vapour phase. Prediction of the pore saturation in partially saturated pores in building materials. Correlation between the electric impedance and the water layer thickness in partially saturated screed samples. T2 - 10. CMM Tagung CY - Ettlingen, Germany DA - 10.10.2019 KW - Embedded sensors KW - Corresponding relative humidity KW - Electrical impedance KW - Material moisture KW - Building materials KW - Partiallly saturated pores PY - 2019 AN - OPUS4-49261 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lugovtsova, Yevgeniya A1 - Prager, Jens A1 - Schubert, Lars A1 - Tschöke, Kilian T1 - Fehlerwechselwirkung in Verbundwerkstoffen mit Geführten Wellen N2 - Der praktische Einsatz von SHM-Verfahren mit geführten Ultraschallwellen basiert auf einem fundierten Verständnis der speziellen physikalischen Zusammenhänge der Wellenausbreitung. Das umfasst nicht nur das multimodale Verhalten, welches von den Dispersionsdiagrammen repräsentiert wird, sondern auch die Vorhersage der Interaktion zwischen verschiedenen Wellenmoden und den zu erwartenden Fehlstellen. Ziel des Workshops ist es, das Verständnis der Ausbreitung geführter Wellen zu verbessern und die vielfältigen Anwendungsmöglichkeiten, die sich aus der multimodalen Wellenausbreitung ergeben, an praktischen Beispielen zu demonstrieren. Die vorgestellten Szenarien beschränken sich dabei nicht nur auf eine Anregung grundlegender Dehnungs- und Biegewellen, sondern beziehen auch geführte Wellenmoden höherer Ordnung zur Verbesserung der Aussagekraft des Prüfergebnisses mit ein. Nach einer theoretischen Einführung werden ausgewählte Demonstratoren, vorrangig mit Bezug zum Automobilbau, vorgestellt. Diese schließen Fragestellungen der Integration der Sensorik in gekrümmte Faserverbundbauteile ebenso mit ein, wie die Überwachung von Metall-Faserverbund-Komposit-Materialien, die in Drucktanks zum Einsatz kommen. T2 - 3. Anwenderseminar Zustandsüberwachung mit geführten Wellen CY - Karlsruhe, Germany DA - 27.03.2019 KW - Wasserstoffspeicher KW - Geführte Ultraschallwellen KW - Kohlenstofffaserverstärkter Kunststoff KW - Faserverbundwerkstoff PY - 2019 AN - OPUS4-48383 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Serrano Munoz, Itziar A1 - Evsevleev, Sergei A1 - Laquai, René A1 - Müller, Bernd R. A1 - Kupsch, Andreas A1 - Bruno, Giovanni T1 - Damage characterization via 2D and 3D X-ray refraction techniques N2 - We present two examples of the potential of synchrotron X-ray refraction techniques. First, we focus on the 3D imaging of hydrogen assisted cracks in an EN AW – 6060 aluminium alloy which are otherwise undetected by absorption-based CT. The second work is a quantitative analysis of the damage evolution in an Al/Al2O3 Metal Matrix Composite during interrupted in-situ tensile load. T2 - International Conference on Tomography of Materials & Structures CY - Cairns, Australia DA - 22.07.2019 KW - X-ray refraction KW - Analyzer-based imaging KW - Aluminum alloy KW - Metal matrix composite KW - Damage characterization PY - 2019 AN - OPUS4-48604 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ahmadi, Samim A1 - Ziegler, Mathias A1 - Thiel, Erik A1 - Hirsch, Philipp Daniel A1 - Karagianni, Christina A1 - Burgholzer, P. A1 - Mayr, G. A1 - Jung, P. A1 - Caire, G. T1 - Thermographic super resolution imaging using structured 1D laser illumination N2 - Thermographic nondestructive evaluation (NDE) is based on the interaction of thermal waves with inhomogeneities. These inhomogeneities are related to sample geometry or material composition. Although thermography is suitable for a wide range of inhomogeneities and materials, the fundamental limitation is the diffusive nature of thermal waves and the need to measure their effect radiometrically at the sample surface only. The propagation of the thermal waves from the heat source to the inhomogeneity and to the detection surface results in a degradation in the spatial resolution of the technique. A new concerted ansatz based on a spatially structured heating and a joint sparsity of the signal ensemble allows an improved reconstruction of inhomogeneities. As a first step to establish an improved thermographic NDE method, an experimental setup was built based on structured 1D illumination using a flash lamp behind a mechanical aperture. As a follow-up to this approach, we now use direct structured illumination using a 1D laser array. The individual emitter cells are driven by a pseudo-random binary pattern and are additionally shifted by fractions of the cell period. The repeated measurement of these different configurations enables to illuminate each spot of the sample surface in lateral direction. This allows for a reconstruction that makes use of joint sparsity. The measured data set is processed using super resolution image reconstruction algorithms such as the iterative joint sparsity (IJOSP) algorithm. Using this reconstruction technique and 150 different illumination patterns results in a spatial resolution enhancement of approximately a factor of four compared to the resolution of 5.9 mm for homogenously illuminated thermographic reconstruction. Further, new data processing techniques have been studied before applying the IJOSP algorithm that are more performant or less prone to errors regarding image reconstruction. The choice of regularization parameters in data processing as well as experimental parameters such as the illumination pattern as a variable heat flux density (i.e., the Neumann boundary condition for convolution with the constant Green's function) have a big influence on the reconstruction goodness. With analytical-numerical modelling and numerical FEM simulations, we studied the influence of the experimental parameters on the result of the non-linear IJOSP reconstruction. This has also been investigated experimentally e.g. using different laser line widths or more measurements per position. These studies are used to derive optimal conditions for a certain measurement image reconstruction technique. T2 - 20-th International Conference on Photoacoustic and Photothermal Phenomena CY - Moscow, Russia DA - 07.07.2019 KW - Super resolution KW - Virtual wave KW - Laser thermography KW - 1d laser KW - Joint sparsity KW - Laser array KW - VCSEL array KW - High-power laser PY - 2019 AN - OPUS4-48578 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ahmadi, Samim A1 - Ziegler, Mathias A1 - Thiel, Erik A1 - Hirsch, Philipp Daniel A1 - Karagianni, Christina A1 - Burgholzer, P. A1 - Mayr, G. A1 - Jung, P. A1 - Caire, G. T1 - Photothermal super resolution imaging: a comparison of different reconstruction techniques N2 - The diffusive nature of heat propagation complicates the separation of two closely spaced defects. This results in a fundamental limitation in spatial resolution. Therefore, super resolution (SR) image reconstruction can be used. SR processing techniques based on spatially structured heating and joint sparsity of the signal ensemble allows for an improved reconstruction of closely spaced defects. This new technique has been studied using a 1D laser array with randomly chosen illumination pattern. This paper presents the results after applying SR algorithms such as the iterative joint sparsity (IJOSP) algorithm, to our processed measurement data. Two different data processing strategies are evaluated and discussed regarding their influence on the reconstruction goodness as well as their complexity. Moreover, the degradation of the SR reconstruction by the choice of regularization parameters in data processing is discussed. The application of both SR techniques that are evaluated in this paper results in a spatial resolution enhancement of approximately a factor of four which leads to a better separation of two closely spaced defects. The fundamental difference between both SR techniques is their complexity. T2 - 46th Annual Review of Profress in Quantitative Nondestructive Evaluation CY - Portland, OR, USA DA - 14.07.2019 KW - Super resolution KW - Virtual wave KW - Laser thermography KW - 1d laser KW - Joint sparsity KW - Laser array KW - VCSEL array KW - High-power laser KW - Fourier transform KW - Dimension reduction PY - 2019 AN - OPUS4-48579 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ahmadi, Samim A1 - Ziegler, Mathias A1 - Thiel, Erik A1 - Hirsch, Philipp Daniel A1 - Karagianni, Christina A1 - Burgholzer, P. A1 - Mayr, G. A1 - Jung, P. A1 - Caire, G. T1 - Photothermal super resolution image reconstruction using structured 1d laser illumination N2 - The separation of two closely spaced defects in fields of Thermographic NDE is very challenging. The diffusive nature of thermal waves leads to a fundamental limitation in spatial resolution. Therefore, super resolution image reconstruction can be used. A new concerted ansatz based on spatially structured heating and joint sparsity of the signal ensemble allows for an improved reconstruction of closely spaced defects. This new technique has been studied using a 1D laser array with randomly chosen illumination pattern. This paper presents the results after applying super resolution algorithms, such as the iterative joint sparsity (IJOSP) algorithm, to our processed measurement data. Different data processing techniques before applying the IJOSP algorithm as well as the influence of regularization parameters in the data processing techniques are discussed. Moreover, the degradation of super resolution reconstruction goodness by the choice of experimental parameters such as laser line width or number of measurements is shown. The application of the super resolution results in a spatial resolution enhancement of approximately a factor of four which leads to a better separation of two closely spaced defects. T2 - 46th Annual Review of Profress in Quantitative Nondestructive Evaluation CY - Portland, OR, USA DA - 14.07.2019 KW - Super resolution KW - Virtual wave KW - Laser thermography KW - 1d laser KW - Joint sparsity KW - Laser array KW - VCSEL array KW - High-power laser PY - 2019 AN - OPUS4-48591 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ahmadi, Samim A1 - Ziegler, Mathias A1 - Thiel, Erik A1 - Hirsch, Philipp Daniel A1 - Karagianni, Christina A1 - Burgholzer, P. A1 - Mayr, G. A1 - Jung, P. A1 - Caire, G. T1 - A comparison of different techniques for photothermal super resolution image reconstruction N2 - The separation of two closely located defects in fields of Thermographic NDE is very challenging. The diffusive nature of thermal waves leads to a fundamental limitation in spatial resolution. Therefore, super resolution image reconstruction can be used. A new concerted ansatz based on spatially structured heating and joint sparsity of the signal ensemble allows an improved reconstruction of closely located defects. This new technique has also been studied using 1D laser arrays in active thermography. The post-processing can be roughly described by two steps: 1. Finding a sparse basis representation using a reconstruction algorithm such as the Fourier transform, 2. Application of an iterative joint sparsity (IJOSP) method to the firstly reconstructed data. For this reason, different methods in post-processing can be compared using the same measured data set. The focus in this work was the variation of reconstruction algorithms in step 1 and its influence on the results from step 2. More precise, the measured thermal waves can be transformed to virtual (ultrasound) waves that can be processed by applying ultrasound reconstruction algorithms and finally the super resolution algorithm. Otherwise, it is also possible to make use of a Fourier transform with a subsequent super resolution routine. These super resolution thermographic image reconstruction techniques in post-processing are discussed and evaluated regarding performance, accuracy and repeatability. T2 - 20-th International Conference on Photoacoustic and Photothermal Phenomena CY - Moscow, Russia DA - 07.07.2019 KW - Super resolution KW - Virtual wave KW - Laser thermography KW - 1d laser KW - Joint sparsity KW - Laser array KW - VCSEL array KW - High-power laser KW - Fourier transform KW - Dimension reduction PY - 2019 AN - OPUS4-48592 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Illemann, J. A1 - Meinel, Dietmar A1 - Bellon, Carsten T1 - Effektive Bestimmung der Fokusparameter von Mikrofokus-Röntgenquellen N2 - Mikrofokus-Röntgenquellen werden in der industriellen CT flexibelverwendet, um mit kleiner Leistung hohe Auflösung zu erzielen oder mit verminderter Auflösung bei höherer Leistung kürzere Messzeiten zu erreichen. Insbesondere Quellen in offener Bauweise benötigen Wartung wie Filamentwechsel und Nachstellen der Fokusparameter. Ziel ist es, einen optimal kleinen Quellfleck bei bekannter Spannung einzustellen und dessen Größe zu bestimmen. Zur Überprüfung der Quellfleckgröße sind bereits Verfahren unter Verwendung lithographisch hergestellter Masken mit Strichmustern oder Siemenssternen aus Mikrometer dünnen Schichten aus stark absorbierendem Material wie z.B. Gold bekannt. Diese erfordern wegen der geringen Absorption eine lange Messzeit und sind nur kostenintensiv herzustellen. Ihre Verwendung zur regelmäßigen Qualitätsüberprüfung von CT-Anlagen ist daher nicht verbreitet. Ziel dieser Arbeit ist es, die richtungsabhängige Quellfleckgröße absolut zu bestimmen, wobei nur einfach zu beschaffende Wolframspitzen verwendet werden. Dazu werden radiographische Bilder in hoher Vergrößerung aufgenommen und die Grauwertverteilung parametrisiert. Unter Verwendung der Kenntnis von Targetmaterial und Spannung wird eine eineindeutige Zuordnung zur Quellfleckgröße vorgenommen. Dieses erfordert eine extensive Simulation für verschiedene Spannungen, Fokusgrößen und andere Einflussgrößen, sowie die experimentelle Verifikation an verschiedenen CT-Anlagen im Vergleich zu einer bekannten Methode. Erste Ergebnisse werden vorgestellt und die praktische Implementierung unter Angabe der Einschränkungen der Verwendbarkeit diskutiert. Die Autoren hoffen, damit einen wesentlichen Beitrag zur Verbesserung der Qualitätssicherung und zur Arbeitseffizienz in der Mikrocomputertomographie leisten zu können. T2 - DGZfP DACH-Jahrestagung 2019 CY - Friedrichshafen, Germany DA - 27.05.2019 KW - Mikro-Computertomographie KW - Röntgenröhre KW - Quellfleckgröße KW - Brennfleck PY - 2019 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-485960 UR - https://www.ndt.net/search/docs.php3?id=24551 UR - https://www.ndt.net/article/dgzfp2019/papers/Mi.2.A.3.pdf IS - NDT.net Issue: 2019-08 SP - 1 EP - 13 AN - OPUS4-48596 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hillger, W. A1 - Szewieczek, A. A1 - Gaal, Mate A1 - Bente, Klaas T1 - Charakterisierung von Luftultraschallprüfköpfen mit thermoakustischen Wandlern N2 - Nicht nur die Qualitätssicherung von Bauteilen wird immer wichtiger und muss immer höheren Anforderungen entsprechen, sondern auch die dafür verwendete Prüfeinrichtung und die Sensorik. Für die Qualitätssicherung von Ultraschall-Prüfköpfen mit Luftankopplung bestand die bisherige Lösung darin, baugleiche Wandler als Aktuatoren (Referenzsender) einzusetzen. Für eine Weiterentwicklung der Wandler ist eine akustische Quelle wünschenswert, die eine weit größere Bandbreite mit flachem Frequenzgang aufweist, als die zu untersuchenden Prüfköpfe. Hier bieten sich thermoakustische Wandler an, die keine ausgeprägten Resonanzen haben und über eine hohe Bandbreite verfügen (min. 10 kHz bis 1 MHz). Diese wurden von der BAM in Berlin entwickelt und decken den Frequenzbereich von typischen Luftultraschall-Prüfköpfen vollständig ab. Der Vortag beschreibt die Besonderheiten der Ansteuerung dieser Wandler, die einen Innenwiderstand von ca. 7 Ohm besitzen und eine Pulsleistung von etwa 10 kW benötigen. Ferner werden erste Ergebnisse der Charakterisierung von unterschiedlichen piezokeramischen Prüfköpfen im Frequenzbereich von 50 kHz bis 500 kHz präsentiert. Beispielhaft zeigte ein Prüfkopf mit mehreren Anpassschichten lokale Frequenzunterschiede im Schallfeld. T2 - DACH-Jahrestagung 2019 CY - Friedrichshafen, Germany DA - 27.05.2019 KW - Ultrasound KW - Air coupled ultrasound KW - Thermoacoustics PY - 2019 UR - https://jahrestagung.dgzfp.de/Portals/jt2019/Dokumente/Kufa_GESAMT_klein_.pdf AN - OPUS4-48255 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -