TY - JOUR A1 - Rashidi, Reza A1 - Vaerst, Olivia A1 - Riechers, Birte A1 - Rösner, Harald A1 - Wilde, Gerhard A1 - Maaß, Robert T1 - Atomic-scale strain fluctuations as an origin for elastic microstructures in metallic glasses N2 - Metallic glasses (MGs) exhibit an elastic microstructure that spans from a few to hundreds of nanometers, the origin of which continues to remain poorly understood. Here we employ four-dimensional scanning transmission electron microscopy (4D-STEM) on a Zr65Cu25Al10 (at. %) bulk MG. Mapping local diffraction patterns over representative areas also probed elastically with automated nanoindentation, two comparable correlation length scales have been identified. Specifically, local diffraction patterns are analyzed with respect to their ellipticity, revealing systematic fluctuations between positive and negative volumetric strains. A power spectrum analysis of the strain fluctuations returns a dominant length scale of the order of 100 nm, which is very much compatible with what elastic property mapping indicates. Annealing reduces the magnitude of the statistical strain fluctuations, without strongly affecting the associated fluctuation length scale. These findings demonstrate that atomic-scale strains are very likely the origin of the structurally unexpected large elastic fluctuations obtained in nanoscale contact mechanics experiments. KW - Metallic glass KW - 4D-STEM KW - Strain anisotropy KW - Nanoindentation KW - Elastic microstructure KW - Heterogeneities PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-654991 DO - https://doi.org/10.1016/j.actamat.2026.121982 SN - 1359-6454 VL - 308 SP - 1 EP - 8 PB - Elsevier Inc. AN - OPUS4-65499 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schröder, Nina A1 - Uhlig, Marvin A1 - Kromm, Arne A1 - Schröpfer, Dirk A1 - Höfer, Kevin A1 - Hensel, Jonas A1 - Kannengießer, Thomas T1 - Challenges in the evaluation of the weldability of old mild steels for future use N2 - For reasons of sustainability and cost efficiency, there is an increasing trend in the steel-processing industry to retrofit existing structures, avoiding costly shutdowns or dismantling. Although welding is a cost-effective joining method, it is rarely applied to old steels, whereas riveted or bolted connections are often uneconomical. Repair and refurbishment frequently require the replacement of damaged material or the creation of dissimilar old–new steel joints. Due to the varied manufacturing processes of historical steels, not all twentieth-century steels are inherently weldable, making an initial assessment of weldability essential. In this study, a historical non-deoxidized mild steel (produced by Siemens–Martin processing) originating from the construction of the Berlin Radio Tower (erected in 1926) was investigated using dilatometry to analyze its welding behavior. A database of welding CCT diagrams and HAZ simulations was established to support practice-oriented welding experiments, providing key insights into their weld-metallurgical behavior and weldability. Furthermore, initial welding trials were conducted, and the local residual stress states in dissimilar old–new steel joints were determined. These foundational investigations are critical for the development of innovative, load-adapted welding concepts for the repair and refurbishment of existing old-steel infrastructure in Germany. KW - Old mild steels KW - Repair welding KW - Weldability KW - Thermo-physical simulation KW - CCT diagrams PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-654784 DO - https://doi.org/10.1007/s40194-026-02366-6 SN - 1878-6669 SP - 1 EP - 14 PB - Springer nature AN - OPUS4-65478 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Merino, E. A1 - Cere, S. A1 - Özcan Sandikcioglu, Özlem A1 - Dimper, Matthias A1 - Sobrados, I. A1 - Durán, A. A1 - Castro, Y. T1 - Influence of the BF3·O(C2H5)2 on the corrosion resistance of hybrid silica sol-gel coatings deposited on flash-PEO-treated Mg alloy N2 - Achieving highly cross-linked sol-gel coatings to provide effective corrosion protection of Mg alloys remains a challenging task. The aim of this work is to evaluate the effect boron trifluoride diethyl etherate (BF3·O(C2H5)2) as catalyst to epoxy group in a GPTMS/TEOS/SiO2 sol and assesses its effect on the structure and corrosion resistance properties of Flash-PEO coated pre-treated Mg alloy. 29Si MAS NMR and 13C CPMAS-NMR demonstrated that (BF3·O(C2H5)2) efficiently promotes the epoxy polymerization of the GPTMS and the formation of a hybrid silica network. However, the amount of (BF3·O(C2H5)2) should be optimized to minimize the formation of undesirable byproducts such as ethyl ether terminal units. Therefore, GPTMS/TEOS/SiO2 sols containing different amounts of (BF3·O(C2H5)2) were synthesized and deposited onto the Flash-PEO coated Mg alloy, leading to bilayer systems with a total thickness of ⁓8 μm. The corrosion behavior of the bilayer coatings in 3.5 wt% NaCl solution was evaluated by electrochemical impedance spectroscopy (EIS) and Scanning Kelvin probe microscope (SKPFM). The results revealed that the barrier properties of the coatings with enhanced cross-linked structure showed impedance modulus (│Z│f:0.1 Hz) approximately four orders of magnitude higher than the bare magnesium alloy and two orders of magnitude higher than the F-PEO coated sample. A suitable compromise between (BF3·O(C2H5)2) amount and sol-gel film structure is required to obtain a more durable barrier coating capable to extend the protective lifespan of the magnesium alloy. KW - Sol-gel KW - Corrosion KW - AZ31B Mg alloy KW - Chemical structure KW - SKPFM PY - 2026 DO - https://doi.org/10.1016/j.surfcoat.2025.133055 SN - 0257-8972 VL - 522 SP - 1 EP - 13 PB - Elsevier B.V. AN - OPUS4-65416 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Valet, Svenja A1 - Bohlmann, Tatjana A1 - Ebell, Gino A1 - Burkert, Andreas T1 - pH sensitive gel pads for the visualization of anodes and cathodes on zinc N2 - Zinc and zinc alloys have many applications. Zinc corrosion takes place in the atmosphere and is assumed to follow the water drop theory (a macroelement), in which the anode is at the centre of the drop and is surrounded by a cathode. This paper is the first to use gel electrolytes made of agar to visualize anodic and cathodic areas on zinc samples in order to examine the water drop theory. For that, agar gels were added with universal pH indicators, as the anode and cathode exhibit different pH values. In this paper, different amounts of pH indicators were tested to determine whether the indicator influences the potential, the impedance, phase shift, corrosion current and potential and corrosion layer resistance. KW - Corrosion KW - Zinc KW - Gel electrolyte PY - 2026 DO - https://doi.org/10.1016/j.electacta.2026.148134 SN - 0013-4686 VL - 551 SP - 1 EP - 21 PB - Elsevier Ltd. AN - OPUS4-65308 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Burkert, Andreas T1 - Grundlagen Spannungsrisskorrosion N2 - Der Vortrag stellt die Grundlagen und Schädigungsmechanismen der Spannungsrisskorrosion an metallenen Werkstoffen vor. Aus dem Zusammenspiel von mechanischer Beanspruchung, dem Korrosionsmedium und den Eigenschaften des Werkstoffs können sich Bedingungen ergeben, welche den Eintritt von SpRK begünstigen können. Speziell wird auf auf die chloridinduzierte Spannungsrisskorrosion und die wasserstoffinduzierte SpRK näher eingegangen. Abschließend werden einige normative Prüfmöglichkeiten vorgestellt. T2 - Korrsosionsschutz in der maritimen Technik CY - Hamburg, Germany DA - 28.01.2026 KW - Spannstahl KW - Spannungsrisskorrosion KW - Nichtrostender Stahl KW - Korrosion PY - 2026 AN - OPUS4-65425 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Avila Calderon, Luis Alexander A1 - Schriever, Sina A1 - Hang, Y. A1 - Olbricht, Jürgen A1 - Portella, P. D. A1 - Skrotzki, Birgit T1 - Creep reference data of single-crystal Ni-based superalloy CMSX-6 N2 - The article presents creep data for the single-crystal, [001]-oriented nickel-based superalloy CMSX-6, tested at a temperature of 980 °C under initial stresses ranging from 140 MPa to 230 MPa. The constant-load creep experiments were performed in accordance with DIN EN ISO 204:2019–4 standard within an ISO 17025 accredited laboratory. A total of 12 datasets are included, each of which includes the percentage creep extension as a function of time. The data series and associated metadata were systematically documented using a data schema specifically developed for creep data of single-crystal Ni-based superalloys. This dataset serves multiple purposes: it can be used to compare with one's own creep test results on similar materials, to verify testing setups (e.g., by replicating tests on the same or comparable materials), to calibrate and validate creep models, and to support alloy development efforts. KW - NFDI MatWerk KW - Referenzdaten KW - Kriechen KW - CMSX-6 KW - Digitalisierung PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-654056 DO - https://doi.org/10.1016/j.dib.2025.112436 VL - 65 SP - 1 EP - 11 PB - Elsevier AN - OPUS4-65405 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bär, J. A1 - Kanna, N.K. A1 - Duarte, Larissa A1 - Madia, Mauro T1 - Determination of the Kitagawa-Takahashi Diagram using DC Potential Drop Measurements N2 - The Kitagawa-Takahashi Diagram is an important tool for describing the fatigue limit of components containing defects. The models used for its description differ, particularly in the transition region corresponding to the short crack regime. Therefore, for a reliable statement about the fatigue limit in this area, an experimental validation of the models is necessary. However, the standardized staircase method requires a large number of samples and has a long test duration. In this work, a method is presented that allows a simpler and faster validation of the Kitagawa-Takahashi Diagram in the region of short cracks. Rectangular notches with a defined width and depth were manufactured in flat samples of a low-alloyed steel with two different heat treatments using an engraving laser. This method allows a rapid production of very sharp notches without plastic deformation and with only a slight thermal influence on the surrounding material. The samples prepared in this way were fatigued with block wise increasing loads until failure. Cracks are detected by means of a Direct Current Potential Drop method. The length of the loading block (number of cycles) is determined by the measured potential drop. This procedure enables a reliable and precise determination of the limit stress for the respective notch size with low experimental effort and time consumption. The tests have shown that in case of the normalized steel none of the models describes the determined values for the fatigue limit. For the hardened steel, the plot of the fatigue limit as a function of the Murakami parameter √area in combination with the El Haddad model allows a satisfactory description of the measured values. T2 - 5th International Symposium on Fatigue Design and Material Defects CY - Trento, Italy DA - 14.05.2025 KW - Kitagawa-Takahashi diagram KW - Damage tolerance KW - Fatigue KW - Potential drop KW - Fracture mechanics PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-655519 DO - https://doi.org/10.1016/j.prostr.2025.12.283 VL - 76 SP - 27 EP - 34 PB - Elsevier B.V. AN - OPUS4-65551 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Witte, Julien A1 - Treutler, Kai A1 - Schröpfer, Dirk A1 - Kannengießer, Thomas T1 - Influence of Microstructure on the Machinability and Surface Integrity of Additively Manufactured Iron Aluminides N2 - The increasing global focus on energy and resource efficiency has stimulated a growing interest in additive manufacturing. AM offers economic advantages and enables an efficient use of materials. However, AM components often require subsequent mechanical post-processing, such as machining (e.g. milling), to achieve the final contours or surfaces. This is a particular challenge due to the heterogeneous and anisotropic nature of AM structures, which affect machining and the resulting component properties. High-performance materials such as iron aluminide represent a promising alternative to conventional high-temperature materials with a significant economic advantage. However, the strength and hardness properties, which are advantageous for applications in highly stressed lightweight components, pose a challenge for economical machining in addition to the AM microstructure properties. The difficult-to-cut material causes accelerated tool wear and insufficient surface quality. This study shows that crack-free additive manufacturing of the three-component system of iron-nickel-aluminum is possible, and advantages in terms of machinability compared to FeAl-AM components are achieved. The more homogeneous microstructure leads to a reduction in cutting forces, with positive effects on the machinability and optimized surface integrity. Ultrasonic assisted milling (USAM) offers great potential to address the major challenges posed by difficult-to-cut materials and additively manufactured weld structures. Therefore, this study focuses on assessing the transferability of previous positive results by USAM to the selected iron aluminide alloys. The machinability of the aluminides is analyzed by varying significant influencing variables in finish milling experiments and evaluated in terms of the loads on the tool and the resulting surface integrity. T2 - AA Meeting of Commission IX ‘Behavior of Metals subject to Welding’ CY - Rhodes, Greece DA - 08.07.2024 KW - Iron aluminide KW - Additive manufacturing KW - Machinability KW - Surface integrity KW - Ultrasonic-assisted milling PY - 2026 SP - 1 EP - 16 AN - OPUS4-65530 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erning, Johann Wilhelm T1 - Werkstoffe im Kontakt mit Trinkwasser: Von den UBA-Bewertungsgrundlagen nach Europa N2 - Die Grundlagen der hygienischen Bewertung von Werkstoffen im Kontakt mit Trinkwasser werden erläutert. Die regulatorischen Hintergründe und die Überführung der Regeln in den europäischen rahmen werden diskutiert und an Beispielen erläutert T2 - Abschlusskonferenz ZEP-Fittings CY - Lüdenscheid, Germany DA - 05.02.2026 KW - Korrosion KW - Trinkwasserhygiene KW - Europa KW - Werkstoffe PY - 2026 AN - OPUS4-65536 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Gerrits, Ruben A1 - Stepec, Biwen An A1 - Bäßler, Ralph A1 - Becker, Roland A1 - Dimper, Matthias A1 - Feldmann, Ines A1 - Goff, Kira L. A1 - Günster, Jens A1 - Hofmann, Andrea A1 - Hesse, René A1 - Kirstein, Sarah A1 - Klein, Ulrich A1 - Mauch, Tatjana A1 - Neumann-Schaal, Meina A1 - Özcan Sandikcioglu, Özlem A1 - Taylor, Nicole M. A1 - Schumacher, Julia A1 - Shen, Yin A1 - Strehlau, Heike A1 - Weise, Matthias A1 - Wolf, Jacqueline A1 - Yurkov, Andrey A1 - Gieg, Lisa M. A1 - Gorbushina, Anna T1 - A 30-year-old diesel tank: Fungal-dominated biofilms cause local corrosion of galvanised steel N2 - The increased use of biodiesel is expected to lead to more microbial corrosion, fouling and fuel degradation issues. In this context, we have analysed the metal, fuel and microbiology of a fouled diesel tank which had been in service for over 30 years. The fuel itself, a B7 biodiesel blend, was not degraded, and—although no free water phase was visible—contained a water content of ~60 ppm. The microbial community was dominated by the fungus Amorphotheca resinae, which formed thick, patchy biofilms on the tank bottom and walls. The tank sheets, composed of galvanised carbon steel, were locally corroded underneath the biofilms, up to a depth of a third of the sheet thickness. On the biofilm-free surfaces, Zn coatings could still be observed. Taken together, A. resinae was shown to thrive in these water-poor conditions, likely enhancing corrosion through the removal of the protective Zn coatings. KW - Fungal biofilms KW - Biodiesel degradation mechanisms PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-655014 DO - https://doi.org/10.1038/s41529-025-00731-2 SN - 2397-2106 VL - 10 IS - 1 SP - 1 EP - 14 PB - Springer Science and Business Media LLC AN - OPUS4-65501 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schröder, Nina T1 - Herausforderungen und Potenziale moderner Hochleistungs-Lichtbogenprozesse für effiziente Reparaturmaßnahmen an Altstahlkonstruktionen N2 - Stahltragwerke, die im späten 19. und frühen 20. Jahrhundert errichtet wurden, stellen noch heute einen wesentlichen Bestandteil der technischen Infrastruktur dar. Ein erheblicher Anteil der Brücken- und Ingenieurbauwerke befindet sich seit mehr als 80 oder sogar 100 Jahren in Betrieb und ist kontinuierlich steigenden Verkehrsaufkommen, Achslasten sowie dynamischen Einwirkungen ausgesetzt. Vor dem Hintergrund dieser zunehmenden Beanspruchungen sind beanspruchungsgerechte und konstruktiv angemessene Instandsetzungsstrategien unerlässlich, um die langfristige strukturelle Integrität sicherzustellen und zugleich den vorhandenen Baubestand nachhaltig zu erhalten. Da historische Stahlkonstruktionen überwiegend für genietete oder geschraubte Verbindungen ausgelegt wurden, stellt die nachträgliche Umsetzung geschweißter Reparatur- oder Verstärkungsmaßnahmen eine besondere Herausforderung dar. Neben den spezifischen werkstofflichen Eigenschaften alter Flussstähle sind insbesondere schweißbedingte Eigenspannungen sowie mikrostrukturelle Veränderungen zu berücksichtigen, da diese die Tragfähigkeit und das Gesamttragverhalten maßgeblich beeinflussen können. Infolgedessen müssen Instandsetzungskonzepte nicht nur die geometrische Wiederherstellung gewährleisten, sondern zugleich an den tatsächlichen Spannungszustand und die betrieblichen Beanspruchungen des Tragwerks angepasst werden. Vor diesem Hintergrund untersucht die vorliegende Arbeit MAG-Schweißversuche an Mischverbindungen zwischen historischem und modernem Baustahl. Der Nahtöffnungswinkel wurde systematisch zwischen 50° und 30° variiert, um den Einfluss der Fugengeometrie auf das Schweißgutvolumen, die Wärmeeinbringung sowie den resultierenden Eigenspannungszustand zu analysieren. Darüber hinaus kamen innovative Hochleistungs-Lichtbogenprozesse, wie beispielsweise ein modifizierter Sprühlichtbogen, zum Einsatz, um eine kontrollierte und reduzierte Wärmeeinbringung zu ermöglichen. Ziel ist es, schweißbedingte Eigenspannungen durch eine Optimierung von Prozessführung und Fugengestaltung zu minimieren und damit eine technisch fundierte sowie beanspruchungsgerechte Instandsetzungsstrategie für bestehende historische Stahltragwerke mit langfristiger Gebrauchstauglichkeit bereitzustellen. T2 - Forschungsseminar an der OvGU Magdeburg CY - Magdeburg, Germany DA - 18.02.2026 KW - Flussstahl KW - Reparaturmaßnahmen KW - Schweißeignung KW - Modifizierter Sprühlichtbogen KW - Eigenspannungen PY - 2026 AN - OPUS4-65577 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Mantouvalou, I. A1 - Bauer, L.J. A1 - Truong, V.-B. A1 - Wagener, Y. A1 - Förste, F. A1 - Maruchenko, O. A1 - Werner, S. A1 - Lizzi, F. A1 - Wieder, Frank A1 - Wolff, T. A1 - Kanngießer, B. A1 - Zaslansky, P. T1 - Quantitative micro-XRF combined with X-ray imaging reveals correlations between Zn concentration and dentin tubule porosity across entire teeth N2 - Bony materials are biogenic composites of protein fibers and mineral that create hierarchical structures. In the case of teeth, dentin is the main component and similar to other bones, it contains porosity at multiple length scales. It is traversed by micron-sized hollow channels known as dentinal tubules, essential for temperature and pain sensation. Tubule density and thus porosity vary throughout the macroscopic three-dimensional (3D) structure, with porosity increasing toward the pulp. The different densities in teeth are easily revealed non-destructively in 3D by X-ray imaging using computer tomography (CT). Yet elemental composition analysis is more difficult to obtain from within the centimeter-sized heterogeneous bulk material. We describe an approach of merging CT measurements of healthy, intact bovine teeth with micro-X-ray fluorescence (micro-XRF) images of matching serially sectioned slices. Through the combination of multi-resolution quantitative CT measurements with elemental mass fraction derivation, gradients in density and element distributions such as calcium (Ca), phosphorus (P), and zinc (Zn) are revealed across entire teeth in 3D. While the main constituents (Ca and P) are homogeneously distributed in the matrix, Zn concentration increases significantly and exponentially toward the pulp. We find an inverse association between dentin tissue density and Zn concentration localizing this element in or around tubules. Our data serve as a quantitative reference for density and Zn mass fractions in healthy, neither carious nor hypermineralized dentin, as a basis for comparisons across species in health and disease states. KW - Dentin density KW - Micro-computer tomography KW - Quantitative micro-X-ray fluorescence KW - Tubule porosity KW - Zn distribution PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-654215 DO - https://doi.org/10.1002/VIW.20250173 SN - 2688-3988 SN - 2688-268X SP - 1 EP - 14 PB - Wiley Online Library AN - OPUS4-65421 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Bachmann, Marcel A1 - Rethmeier, Michael A1 - Meng, Xiangmeng T1 - Project title: Multi-physical simulation of the influence of an auxiliary magnetic field on the process porosity formation during high-power laser beam welding N2 - In this project, a multiphysically coupled numerical model will be developed to quantitatively describe porosity reduction in high-power laser beam welding of up to 10 mm thick AlMg3 using an oscillating magnetic field. The aim is to gain fundamental insights into the physical dependencies of the introduced electromagnetic forces on the melt pool behavior and the reduction of porosity. With the help of the numerical model, the transient, multi-coupled, three-dimensional problem of heat transfer, liquid flow, free surface deformation, and magnetic induction is to be solved, taking into account temperature-dependent material properties. The numerical modelling of the heat source will integrate all relevant physical mechanisms, for instance, multiple reflections of the laser radiation by an advanced ray tracing model, as well as local Fresnel absorption at the keyhole wall. This allows an analysis of the keyhole fluctuations, which have a dominant influence on the formation of process spores during deep penetration welding, based on physical principles. In addition, further physical factors such as the ablation pressure of the evaporating metal, the Laplace pressure, and Marangoni shear stresses are also to be integrated into the model. To evaluate the pore formation and reduction by means of the electromagnetic forces introduced in the molten pool, suitable models for describing the movement of the pores in the melt are to be developed. For the process pores, their movement can be implemented by tracking their surface under consideration of their internal pressure and temperature. With the help of the simulation model, all key factors for the formation of process pores during laser beam welding of the used aluminum alloy, as well as their avoidance, can be decoupled and analyzed. Accompanying welding tests are planned at BAM on a 20 kW fiber laser and a 16 kW disk laser. The magnetic flux density will be up to 500 mT at a maximum frequency of 5 kHz. The experimental results, in particular temperature measurements, weld cross sections, computer tomography, and X-ray examinations, will be used to verify the multiphysical model and its calibration. Moreover, the models will be validated and quantified by in situ high-speed imaging of the keyhole dynamics in a metal/quartz glass configuration with keyhole illumination by a diode laser coaxial to the processing laser. On the basis of the numerical and experimental results, the dependencies between applied magnetic field, melt pool behavior, and porosity formation will be revealed in this project. KW - Laser beam welding KW - Electromagnetic weld pool control KW - Numerical simulation KW - Process porosity PY - 2026 DO - https://doi.org/10.34657/27669 SP - 1 EP - 14 AN - OPUS4-65335 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bachmann, Marcel A1 - Putra, Stephen Nugraha A1 - Yang, Fan A1 - Meng, Xiangmeng A1 - Pusbatzkies, Pablo A1 - Rethmeier, Michael T1 - Elucidation of the laser beam energy attenuation by the vapor plume formation during high-power laser beam welding N2 - In high-power laser beam welding, a common phenomenon is the formation of a keyhole caused by the rapid evaporation of the material. Under atmospheric pressure, this evaporation generates a vapor plume that interacts with the laser beam, leading to energy attenuation and scattering of the laser radiation along its path. These interactions affect the stability of the process and the overall weld quality. This study investigates the influence of the vapor plume on the weld pool and keyhole dynamics during high-power laser beam welding of AlMg3 aluminum alloy through experimental and numerical approaches. The primary goal is to identify key vapor plume characteristics, particularly its length fluctuations, and to improve the accuracy of the numerical models. To achieve this, an algorithm was developed for the automated measurement of the vapor plume length using high-speed imaging and advanced data processing techniques. The measured plume length is then used to estimate additional vapor heating and laser energy attenuation using the Beer–Lambert law. A refined numerical CFD model, incorporating 3D transient heat transfer, fluid flow, and ray tracing, was developed to evaluate the vapor plume’s impact. Results show that already the time-averaged plume length effectively captures its transient influence and aligns well with experimental weld seam geometries. Additionally, energy scattering and absorption caused by the vapor plume led to a wider weld pool at the top surface. The study also shows an increased percentage of keyhole collapses due to the reduced laser power absorption at the keyhole bottom, further highlighting the importance of accurately modeling vapor plume effects. T2 - International Congress of Applications of Lasers & Electro-Optics 2025 CY - Orlando, USA DA - 12.10.2025 KW - Laser beam welding KW - Vapor plume formation KW - Weld pool KW - Keyhole dynamics KW - Numerical modeling PY - 2026 DO - https://doi.org/10.2351/7.0001863 SN - 1938-1387 IS - 38 SP - 012001-1 EP - 012001-9 PB - Laser Institute of America AN - OPUS4-64949 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Czeskleba, Denis A1 - Rhode, Michael A1 - Wandtke, Karsten A1 - Irfan, Muhammad Dary A1 - Kannengiesser, Thomas T1 - Hydrogen diffusion in thick-walled S690 saw joints: part 1—experimental determination of microstructure-dependent diffusion coefficients N2 - High-strength low-alloyed steel S690 is widely used in heavy-duty applications, such as structural components, mobile cranes, and industrial plant construction, owing to their high strength and weldability. However, thick-plate submerged arc welding (SAW) can introduce elevated hydrogen levels and residual stresses that promote time-delayed hydrogen-assisted cold cracking (HACC). Accurate, microstructure-specific diffusion data are scarce, limiting predictive HACC assessments. This study presents an experimental determination of hydrogen diffusion coefficients (DH) in two S690 variants: thermomechanically rolled (S690MC) and quenched and tempered (S690Q). Multi-layer SAW welds were produced from 30 mm thick plate material at three heat input levels, and diffusion membranes were extracted from weld metal (WM), heat-affected zone (HAZ), and base material (BM). Hydrogen permeation tests, conducted in accordance with DIN En ISO 17081, yielded flux curves normalized in time from which DH was derived using the inflection-point method. At room temperature, DH values ranged from 6 × 10−5 mm2/s to 9 × 10−5 mm2/s across all regions and heat inputs, with no significant difference between S690MC and S690Q. Weld metal exhibited marginally lower DH, attributed to enhanced hydrogen trapping, while base material measurements showed greater variability. These microstructure-resolved diffusion coefficients add quantitative data for modern S690 SAW welds and provide internally consistent input parameters for the numerical simulations presented in part 2. The results support improved parameterization for subsequent assessments of HACC risk through the optimization of welding parameters. KW - Hydrogen assisted cracking KW - Submerged arc welding KW - Diffusion KW - Electrochemical permeation KW - Microstructure PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-655711 DO - https://doi.org/10.1007/s40194-026-02400-7 SN - 0043-2288 SP - 1 EP - 15 PB - Springer Science and Business Media LLC AN - OPUS4-65571 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Czeskleba, Denis A1 - Rhode, Michael A1 - Wandtke, Karsten A1 - Irfan, Muhammad Dary A1 - Kannengiesser, Thomas T1 - Hydrogen diffusion in thick-walled S690 SAW joints: part 2 – predictive modeling of heat input and microstructure influence N2 - High-strength low-alloy (HSLA) steels such as S690 are widely employed in thick-walled welded structures, where hydrogen-assisted cold cracking (HACC) remains a persistent concern. While microstructure-specific hydrogen diffusion coefficients (DH) for weld metal (WM), heat-affected zone (HAZ), and base material (BM) were experimentally established in Part 1 of this study, their quantitative influence on hydrogen accumulation and effusion has not yet been fully clarified. This work presents a transient, spatially resolved numerical model for simulating hydrogen transport in multi-pass submerged arc welds. The model integrates experimentally determined DH values with realistic thermal cycles and temperature-dependent boundary conditions. Developed in Python, the simulation tool is purpose-built for hydrogen diffusion in welded joints. It offers a focused, transparent alternative. It offers a focused, transparent alternative to general-purpose finite element platforms. Parametric analyses demonstrate that, although the diffusion coefficients vary by up to 50%, their impact on overall hydrogen retention is minor. In contrast, plate thickness, bead geometry, cooling time (t₈/₅), and interpass temperature exert a dominant influence on hydrogen distribution. Despite clear microstructural differences between the thermomechanically rolled (S690MC) and quenched and tempered (S690Q) variants, including opposite HAZ hardness responses (softening in S690MC, hardening in S690Q) in the (pen)ultimate weld bead, the simulations confirm that their diffusion behavior and hydrogen solubility are closely aligned. Consequently, differences in DH and solubility exert only a minor influence on hydrogen retention compared to thermal exposure and joint geometry. These findings support the interchangeable use of both steel grades in terms of HACC risk due to hydrogen diffusion kinetics under comparable welding conditions. KW - Hydrogen assisted cracking KW - Numerical simulation KW - Diffusion KW - Submerged arc welding PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-655721 DO - https://doi.org/10.1007/s40194-026-02395-1 SN - 0043-2288 SP - 1 EP - 16 PB - Springer Science and Business Media LLC AN - OPUS4-65572 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seifert, Lando T1 - Grundlagen Korrosion und Korrosionsschutz N2 - Im Rahmen des jungen gfkorr Events an der Universität Kassel in diesem Jahr wurde der Grundlagenvortrag vor Young Professionals und Studierenden vorgestellt. Die BAM beschäftigt sich im Fachbereich 7.6 schwerpunktmäßig mit der Korrosionsprüfung, den Korrosionsschäden und -reaktionen rund um Anwendungsfälle der Hauptkonstruktionswerkstoffe Stahl, verzinkter Stahl, Nichtrostende Stähle und Aluminium in relevanten Umgebungsbedingungen. Der Impulsvortrag sollte die Faszination für die Korrosion übermitteln. Dabei wurde anhand von Schadensfällen grundlegende Mechanismen und Haupteinflussfaktoren erörtert. Gestartet wurde mit einem prominenten Versagensfall und Beispiel für Spaltkorrosion aus der Luftfahrt... T2 - die junge gfkorr @ Universität Kassel CY - Kassel, Germany DA - 02.03.2026 KW - Korrosion KW - Korrosionsschutz KW - Stahl KW - Zink KW - Aluminium KW - Nichtrostende Stähle KW - Korrosivität KW - Spaltkorrosion PY - 2026 AN - OPUS4-65614 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Madia, Mauro T1 - Ermittlung von Kitagawa-Takahashi Diagrammen auf der Basis der Schwingbruchmechanik N2 - Das Kitagawa-Takahashi Diagramm ist ein unverzichtbares Werkszeug zur Auslegung von Bauteilen aus fehlerbehafteten Werkstoffen. Zur Beschreibung des Diagramms werden im Allgemeinen die Modelle nach Kitagawa-Takahashi, El Haddad oder Chapetti verwendet, die sich aber im technisch relevanten Bereich zum Teil deutlich voneinander unterscheiden. Daher ist eine experimentelle Absicherung dieses Bereichs zwingend erforderlich. Im Rahmen dieser Arbeit wurden verschiedene Methoden zur experimentellen Absicherung miteinander verglichen, mit dem Ziel eine einfache und schnelle experimentelle Absicherung des KT-Diagramms zu ermöglichen. Die neue experimentelle Methode hat sich als nützliches Werkzeug zur Validierung von KT-Diagrammen erwiesen. Durch die Erzeugung von Kerben mittels eines Gravierlasers und die Durchführung der Versuche mit Potentialmessung kann das KT-Diagramm eines Werkstoffes schnell und mit wenig Aufwand validiert werden. T2 - 58. Tagung des Arbeitskreises Bruchmechanik und Bauteilsicherheit CY - Stuttgart, Germany DA - 24.02.2026 KW - Schwingbruchmechanik KW - Ermüdungsfestigkeit KW - Kitagawa-Takahashi Diagramm KW - Gleichstrom-Potentialsonde PY - 2026 AN - OPUS4-65645 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Madia, Mauro T1 - Ermittlung des intrinsischen Schwellenwerts und dessen Validierung als Werkstoffparameter N2 - Zuverlässige Rissfortschrittsdaten sind notwendig für die sichere Bewertung zyklisch beanspruchter Bauteile. Diese werden häufig im Schwellenwertbereich betrieben, daher ist die genaue experimentelle Ermittlung der Schwellenwerte gegen Rissausbreitung wichtig, um die Unsicherheit der Lebensdauerprognose zu minimieren. Viele Faktoren können die experimentellen Ergebnisse beeinflussen, u.a. die Versuchsparameter und die Umgebungsbedingungen. Diese Arbeit zeigt, dass der intrinsische Schwellenwert von der experimentellen Verfahren und von der Umgebung unabhängig ist. Daraus kann man schließen, dass der intrinsische Schwellenwert als Werkstoffparameter betrachtet werden kann. T2 - Workshop Schwellenwert CY - Munich, Germany DA - 26.02.2026 KW - Schwingbruchmechanik KW - Schwellenwert KW - Rissfortschritt KW - Umgebungseffekte PY - 2026 AN - OPUS4-65646 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Yang, Chunliang A1 - Yang, Fan A1 - Meng, Xiangmeng A1 - Putra, Stephen Nugraha A1 - Bachmann, Marcel A1 - Rethmeier, Michael T1 - Phase-field simulation of the dendrite fragmentation by electromagnetic stirring in AA5754 aluminum alloy laser beam welding N2 - A phase-field model including magnetic field induced dendrite fragmentation was established and applied to the cases with different initial crystal nuclear positions for AA5754 aluminum alloy electromagnetic laser beam welding. Compare the calculated results that include dendrite fragmentation caused by the thermal electromagnetic Lorentz force with the results that consider only the thermal electromagnetic Lorentz force, without fragmentation, at the characteristic time instants. Both in the early and late stages, the small fragmentation at the dendrite tip promotes the number of higher-order branches and their growth, especially in the direction perpendicular to the solidification. The later stage fragmentation has the possibility of breaking one grain into several, which verifies the possibility of grain refinement caused by dendrite fragmentation. The fracture surface caused by fragmentation also makes more solid-liquid interfaces and their growth. In addition, the cases with different initial nuclear positions were compared. The grain growth in the low-temperature zone can be inhibited by the equiaxed grains' fragmentation at the high-temperature area (179.8 μm² and 14.7 % start at the center, 115.4 μm² and 9.4 % start at the high-temperature corner, 134.3 μm² and 10.9 % start at the low-temperature corner), which is another kind of grain refinement by the dendrite fragmentation. This kind of inhibition effect on grain growth in the low-temperature region will be enhanced with the increasing time interval between the two crystal nuclei’ appearance (179.8 μm² and 14.7 % when virtual grains appear at t = 4.3803 s and t = 4.3803 s, 134.3 μm² and 10.9 % at t = 4.0977 s and t = 3.9564 s, and 115.4 μm² and 9.4 % at t = 3.8151 s and t = 3.5325 s). KW - Laser beam welding KW - Electromagnetic KW - Aluminum alloys KW - Phase field method KW - Equiaxed grain KW - Dendrite fragmentation PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-656610 DO - https://doi.org/10.1016/j.cwe.2025.100014 SN - 3117-4159 VL - 35 IS - 1 SP - 1 EP - 12 PB - Elsevier B.V. AN - OPUS4-65661 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Meng, Xiangmeng A1 - Bachmann, Marcel A1 - Kising, Pascal A1 - Yang, Fan A1 - Rethmeier, Michael T1 - Prediction of weld pool and keyhole geometries in high-power laser beam welding through a physics-informed generative artificial intelligence approach N2 - The weld pool and keyhole geometries are critical characteristics in evaluating the stability of the high-power laser beam welding (LBW) process and determining the resultant weld quality. However, obtaining these data through experimental or numerical methods remains challenging due to the difficulties in experimental measurements and the high computational demands of numerical modelling. This paper presents a physics-informed generative approach for predicting weld pool and keyhole geometries in the LBW process. With the help of a well experimentally validated numerical model considering the underlying physics in the LBW, the geometries of the weld pool and keyhole under various welding conditions are calculated, serving as the dataset of the generative model. A conditional variational autoencoder model is employed to generate realistic 2D weld pool and keyhole geometries from the welding parameters. We utilize a β-variational autoencoder model with the evidence lower bound loss function and include Kullback–Leibler divergence annealing to better optimize model performance and stability during training. The generated results show a good agreement with the ground truth from the numerical simulation. The proposed approach exhibits the potential of physics-informed generative models for a rapid and accurate prediction of the weld pool geometries across a diverse range of process parameters, offering a computationally efficient alternative to full numerical simulations for process optimization and control in laser beam welding processes. KW - Laser beam welding KW - Generative artificial intelligence KW - Machine learning KW - Numerical simulation KW - Weld pool KW - Keyhole dynamics PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-656621 DO - https://doi.org/10.2351/7.0001862 SN - 1042-346X VL - 38 IS - 1 SP - 1 EP - 8 PB - Laser Institute of America AN - OPUS4-65662 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ziegler, Mathias A1 - Strobach, L. T1 - Infrarotreflektographie und Blitzthermographie zur Sichtbarmachung von historischen Farbschichten am Flugzeug Bücker Bü 181 Bestmann N2 - Die Geschichte eines Flugzeuges ist häufig von unterschiedlichen Nutzungsphasen geprägt. Zum Beispiel ist der Wechsel des Eigentümers eines Flugzeuges häufig mit umfassenden Veränderungen der Farbgebung und Kennzeichnung verbunden. Wenn ein Flugzeug in die Sammlung eines Museums aufgenommen wird, zeigt es entweder den letzten Einsatzzustand oder andere zu späteren Zeiten durchgeführte Reparaturen auf seiner Oberfläche. Oft befinden sich unterhalb dieser letzten äußeren Schicht, ältere Spuren der Nutzung. Um diese verdeckt liegenden Lackierungen sichtbar zu machen, können die Verfahren der Infrarotreflektographie und der aktiven Thermographie eingesetzt werden. Die Infrarotreflektographie wird häufig in der Gemälderestaurierung eingesetzt, um zum Beispiel Vorzeichnungen sichtbar zu machen. Die aus der industriellen zerstörungsfreien Prüfung bekannten Verfahren der aktiven Thermographie fanden bisher überwiegend im Bereich der Bauwerksuntersuchungen Anwendung. Erste Ergebnisse zu Farbuntersuchungen an historischen Flugzeugen mit den beiden Verfahren fanden am Deutschen Museum München in Zusammenarbeit mit der TU-München statt. Ein Projekt der HTW-Berlin mit der Bundesanstalt für Materialforschung und –prüfung (BAM) und dem Militärhistorischen Museum Flugplatz Berlin-Gatow greift diese Anwendungsidee auf und vergleicht beide Verfahren. Am Beispiel des Flugzeuges Bücker Bü 181 Bestmann können die Möglichkeiten, Grenzen und Potentiale der Technologien zum gegenwärtigen Entwicklungsstand verdeutlicht werden. T2 - Material Truth CY - Magdeburg, Germany DA - 04.03.2026 KW - Aktive Thermographie KW - Flugzeuggeschichte KW - Zerstörungsfreie Prüfung (ZfP) KW - Infrarotreflektographie PY - 2026 AN - OPUS4-65658 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Engelking, Lorenz A1 - Eissel, A. A1 - Madia, Mauro A1 - Schröpfer, Dirk A1 - Treutler, K. A1 - Kruse, Julius A1 - Kannengießer, Thomas A1 - Wesling, V. T1 - Influence of ultrasonic-assisted milling on surface integrity of additively manufactured components using MSG processes N2 - Additive manufacturing (AM) is increasingly used for producing complex metallic components. Subsequent machining is essential to achieve final geometries and surface conditions. The resulting surface integrity, particularly the near-surface residual stress state, plays a crucial role in component performance and fatigue life. This study investigates the potential of ultrasonic-assisted milling (USAM), a hybrid machining process, to improve surface integrity and machinability compared to conventional milling (CM). Three materials were investigated, two difficult-to-cut materials CoCr26Ni9Mo5W and FeNi36 and a low-alloy steel S355J2C. The CoCr26Ni9Mo5W and FeNi36 were additively manufactured via Directed Energy Deposition (DED)-Arc and then machined with varying cutting speeds and feed rates within a Design of Experiments. USAM exhibited enhanced machinability and surface integrity, particularly at low cutting speeds, by reducing cutting forces up to 40% and shifting near-surface residual stresses from tensile to compressive. For S355J2C, USAM reduced cutting forces by approximately 45% and induced near-surface compressive residual stresses up to approximately −700 MPa. Rotating bending tests (DIN50100) show that USAM increases the technical fatigue limit from 307 MPa (CM) to 341 MPa (USAM), i.e., by ∼11%. These findings highlight the advantages of ultrasonic assistance in post-AM machining, offering enhanced fatigue performance and surface quality for various metallic materials. T2 - 4th International Conference on Advanced Joining Processes 2025 CY - Coimbra, Portugal DA - 16.10.2025 KW - Ultrasonic-assisted milling KW - Residual stress KW - Surface integrity PY - 2026 DO - https://doi.org/10.1177/14644207261416395 SP - 1 EP - 12 PB - Sage Journals AN - OPUS4-65682 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Fabry, Çağtay A1 - Pittner, Andreas A1 - Kaplan, Alexander A1 - Rethmeier, Michael T1 - Digitalisation and Carbon Footprint Evaluation of Gas Metal Arc Welding and Wire-Arc Directed Energy Deposition N2 - This paper showcases how a holistic approach to digitalisation enables data-driven welding applications, exemplarily for a gas metal arc welding (GMAW) laboratory. The workflow integrates advanced process monitoring, synchronised multi-sensor data acquisition and tools for data analytics. A welding domain-specific data exchange format weldx is presented that unifies and aggregates the data sets acquired during process monitoring with final component quality metrics, supporting reuse, traceability, and reproducibility. Two case studies illustrate the approach. First, GMAW parameters are adaptively adjusted according to local seam geometry to compensate joint-preparation deviations from nominal values typical for large-scale steel fabrication. Second, the seamless data aggregation along the welding production chain enables an automatic life-cycle assessment (LCA), quantifying the environmental impacts of additive manufacturing with DED Arc/M and attributing the dominant contributors to the carbon footprint. Collectively, the results indicate that a fully integrated experimental set-up together with standardised data structures and scalable analytics can couple monitoring, control, and sustainability, thereby realising the potential of digitalisation for high-quality and environmentally informed welding production. KW - Digitalisation KW - Arc welding KW - DED-arc KW - Life Cycle Assessment PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-656812 DO - https://doi.org/10.1088/1757-899X/1342/1/012067 SN - 1757-8981 VL - 1342 IS - 1 SP - 1 EP - 15 PB - IOP Publishing AN - OPUS4-65681 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Witte, Julien A1 - Treutler, Kai A1 - Schroepfer, Dirk A1 - Kannengiesser, Thomas A1 - Wesling, Volker T1 - Influence of microstructure on the machinability and surface integrity of additively manufactured iron aluminides N2 - The increasing global focus on energy and resource efficiency has stimulated a growing interest in additive manufacturing. AM offers economic advantages and enables an efficient use of materials. However, AM components often require subsequent mechanical post-processing, such as machining (e.g., milling), to achieve the final contours or surfaces. This is a particular challenge due to the heterogeneous and anisotropic nature of AM structures, which affect machining and the resulting component properties. High-performance materials such as iron aluminide represent a promising alternative to conventional high-temperature materials with a significant economic advantage. However, the strength and hardness properties, which are advantageous for applications in highly stressed lightweight components, pose a challenge for economical machining in addition to the AM microstructure properties. The difficult-to-cut material causes accelerated tool wear and insufficient surface quality. This study shows that crack-free additive manufacturing of the three-component system of iron-nickel-aluminum is possible, and advantages in terms of machinability compared to FeAl-AM components are achieved. The more homogeneous microstructure leads to a reduction in cutting forces, with positive effects on the machinability and optimized surface integrity. Ultrasonic assisted milling (USAM) offers great potential to address the major challenges posed by difficult-to-cut materials and additively manufactured weld structures. Therefore, this study focuses on assessing the transferability of previous positive results by USAM to the selected iron aluminide alloys. The machinability of the aluminides is analyzed by varying significant influencing variables in finish milling experiments and evaluated in terms of the loads on the tool and the resulting surface integrity. KW - Iron aluminide KW - Additive manufacturing KW - Machinability KW - Surface integrity KW - Ultrasonic-assisted milling process PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-656993 DO - https://doi.org/10.1007/s40194-026-02382-6 SN - 0043-2288 SP - 1 EP - 13 PB - Springer Science and Business Media LLC AN - OPUS4-65699 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rhode, Michael T1 - Determination, Assessment and Quantification of Hydrogen in Multi-pass / Multi-layer Weld Joints by Adapted ISO 3690 Samples - DEAQuade - N2 - High-strength, low-alloy (HSLA) structural steels, such as S690 and higher grades, are used in numerous applications, enabling sustainable, lightweight structural construction. However, the welded joints of these steels can be susceptible to hydrogen-assisted cold cracking (HACC), especially in the hardened weld metal (WM) or heat-affected zone (HAZ). HACC in high-strength welds basically involves a critical combination of local, mutually dependent parameters consisting of: (1) a crack-critical microstructure; (2) sufficiently high mechanical stress; and (3) a diffusible hydrogen concentration (HD). In this context, thick-walled steel weld joints typically involve multi-layer welding with several passes. This leads to an effective, empirically known reduction in the global HD in the weld seam. This reduction is due to the repeated reheating of subsequently welded beads or layers, which reduces the local HD in the individual weld beads or layers. However, this has not yet been adequately quantified or described. Bead-on-plate tests, such as ISO 3690, cannot correctly reproduce the local HD distribution in individual welding passes (and thus, the global HD in the entire seam). Therefore, these tests lead to an extremely conservative evaluation of hydrogen ingress and the potential for "self-reduction" of HD due to increased interpass temperature during multi-layer welding, which has not yet been adequately addressed in the literature. Ideally, the local HD in each pass and the global (average) HD of the multi-layer weld would be known immediately after welding. For this reason, the study proposes an approach to address the local, track-, and layer-dependent, as well as global, hardness (HD) of multi-layer welds via a modified ISO 3690 test. To this end, representative welding parameter combinations for selected practical welding processes (e.g., SAW, GMAW, or SMAW) will be carried out as conventional bead-on-plate samples. These samples will be systematically extended by an increasing number of welding passes. Several sample series with an increasing number of beads or layers will be examined. Additionally, the initial HD is varied by methods such as targeted shielding gas variation (e.g., addition of hydrogen in GMAW) or moistened flux/coating (e.g., SAW/SMAW). Based on experimental data (temperature field measurements during welding and determination of temperature-dependent HD coefficients), a numerical hydrogen diffusion model is created. This model calculates the local HD (in the beads) and the HD across the weld cross-section. Additional variation calculations represent heat transfer conditions that were not recorded experimentally and their influence on HD distribution. Finally, we investigate the potential use of the modified ISO 3690 multi-layer geometry for application cases such as (1) predicting the effectiveness and necessity of hydrogen removal heat treatment procedures for given welding parameter sets and (2) extending the HD classification definition (e.g., allowing HD10 use for HSLA steels with RP0.2 > 690 MPa instead of HD5). Finally, an international round robin should be initiated once the concept has been successfully confirmed and verified. T2 - IIW Intermediate Meeting, Com. II-A CY - Bangkok, Thailand DA - 17.03.2026 KW - Hydrogen assisted cracking KW - Multi-pass welding KW - Diffusion KW - Cold cracking test PY - 2026 AN - OPUS4-65716 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Engelking, Lorenz A1 - Madia, Mauro A1 - Schröpfer, Dirk A1 - Kruse, Julius A1 - Saliwan Neumann, Romeo A1 - Kannengießer, Thomas T1 - Influence of Ultrasonic-Assisted Milling on Surface Integrity and Fatigue Strength of a Low Alloy Steel N2 - The milling process significantly influences the surface integrity of metallic components through machining induced near surface residual stresses. Modern hybrid machining processes, such as ultrasonic-assisted milling (USAM), offer the potential to induce beneficial near-surface compressive residual stresses compared to the near-surface tensile residual stresses typically resulting from conventional milling (CM). This study investigates the effects of USAM compared to CM on the near-surface residual stress state and fatigue performance of a S355J2C low-alloy steel. Milling experiments and subsequent rotating bending tests revealed that USAM significantly reduces cutting force by approximately 45% and induces near-surface compressive re sidual stresses as low as −733MPa. This leads to a significant improvement in fatigue strength estimated in approximately 34% compared to polished specimens and 11% compared to the CM. These findings highlight the potential of USAM to enhance the fatigue performance of components made of steel. KW - Fatigue strength KW - Residual stress KW - Surface integrity KW - Surface roughness KW - Ultrasonic-assisted milling PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-657358 DO - https://doi.org/10.1111/ffe.70259 SP - 1 EP - 11 PB - Wiley AN - OPUS4-65735 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kricheldorf, Hans R. A1 - Weidner, Steffen A1 - Meyer, Andreas T1 - Poly(butylene terephthalate): About condensation, cyclization, degradation and elimination reactions in the solid state, and the role of smooth crystal surfaces N2 - Three commercial poly(butylene terephthalate) (PBT) samples - Pocan B1300 (B13), Pocan B1600 (B16), and Addigy P 1210 (AP121) - served as the starting materials for the annealing experiments, which were conducted with and without the addition of esterification and transesterification catalysts. The catalysts used were Sn(II) 2-ethylhexanoate (SnOct₂), Zr(IV) acetylacetonate, and 4-toluene sulfonic acid (TSA). Temperatures varied between 150 and 210 °C. The PBT samples were characterized using differential scanning calorimetry (DSC), gel permeation chromatography (GPC), small-angle X-ray scattering (SAXS), and matrix-assisted laser desorption/ionization time-of-flight (MALDI TOF) mass spectrometry. The MALDI mass spectra of all three samples differed greatly but displayed mass peaks of cycles. Similar results were produced by annealing with SnOct₂ or Zr(acac)₄, which favored the formation of even-numbered cycles within the mass range below m/z 5000, along with slow degradation. TSA favored a more intensive degradation without the formation of cycles or even with the destruction of cycles. PBT chains with two carboxylic (COOH) end groups were the most stable species under all circumstances. The origin of the extremely high melting point of AP121 (241–242 °C) can be explained by the smoothing of crystallite surfaces via transesterification. The results suggest that combining MALDI mass spectrometry and SAXS measurements provides a new way to better understand the solid-state chemistry of PBT and related polyesters. KW - MALDI-TOF MS KW - Polybutylene Terephthalate KW - Crystallization KW - solid state KW - cyclization PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-652844 DO - https://doi.org/10.1016/j.polymdegradstab.2025.111862 SN - 0141-3910 VL - 245 SP - 1 EP - 11 PB - Elsevier Ltd. AN - OPUS4-65284 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Eggert, Lara A1 - Burkert, Andreas T1 - H2Mare-Projekt PtX-Wind - Untersuchung zu bauseitigen Fragestellungen der Korrosion und des Korrosionsschutzes mit Fokus auf die Außenkorrosion von Bau- und Anlagenteilen N2 - Im Teilvorhaben „Untersuchung zu bauseitigen Fragestellungen der Korrosion und des Korrosionsschutzes mit Fokus auf die Außenkorrosion von Bau- und Anlagenteilen“ standen korrosionstechnische Untersuchungen zum Einfluss maritimer Exposition für großtechnische Offshore-Power-to-X-(PtX-) Anlagen im Mittelpunkt. Die Planung und der Betrieb solcher OffshoreProzessanlagen stellen aufgrund der vorherrschenden Umweltbedingungen hohe Anforderungen an die Korrosionsbeständigkeit der eingesetzten Materialien, wobei dem wirksamen Korrosionsschutz eine zentrale Rolle für einen wartungsarmen, langlebigen und umweltverträglichen Anlagenbetrieb zukommt. Vor diesem Hintergrund wurde das Korrosionsverhalten metallischer Werkstoffe und Korrosionsschutzsysteme unter realen maritimen und Offshore-Bedingungen systematisch untersucht. Durch die Verknüpfung normativer und wissenschaftlicher Literaturrecherchen mit kontrollierten Laboruntersuchungen sowie mehrjährigen Expositionsversuchen an ausgewählten maritimen Standorten wurden grundlegende Zusammenhänge zwischen Umweltparametern, Werkstoffeigenschaften, konstruktiven Randbedingungen und Korrosionsmechanismen analysiert. Die gewonnenen Ergebnisse stellen eine repräsentative Datengrundlage zur Charakterisierung der Korrosivitätsbedingungen im maritimen Umfeld dar und bilden eine wissenschaftlich fundierte Basis für die Bewertung, Auslegung und Optimierung von Werkstoffen, Beschichtungen und Korrosionsschutzkonzepten für maritime und Offshore-Anwendungen. KW - Offshore-Power-to-X-Anlagen KW - Maritime Korrosion KW - Korrosionsschutz PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-657965 DO - https://doi.org/10.34657/32992 SP - 1 EP - 32 AN - OPUS4-65796 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Burkert, Andreas A1 - Eggert, Lara T1 - H2Mare-Projekt TransferWind - Übertragung von wissenschaftlichen Erkenntnissen zur bauseitigen maritimen und offshore-Korrosion in die Normung und Erarbeitung einer Handlungsempfehlung zu Korrosionsschutz und -prüfung N2 - Die Werkstoffauswahl und der Korrosionsschutz zur Sicherstellung der Dauerhaftigkeit stellen für den Offshore Bereich noch immer eine Herausforderung dar. Erfahrungen und Regelwerke liegen insbesondere aus dem Bereich von Offshore Windenergieanlagen vor. Diese Regelwerke befinden sich in einem stetigen Prozess der Anpassung an aktuelle Erkenntnisse und Erfahrungen, da es sich noch um relativ neue Anwendungen handelt. Für Offshore-Prozessanlagen, wie diese im H2Mare-Projekt betrachtet werden, sind die Anforderungen wesentlich komplexer, da Anlagenkomponenten den Beanspruchungen aus den Prozessen im Inneren der Anlagen ebenso genügen müssen, wie den Beanspruchungen aus der maritimen Umgebung. Hier kommen im Vergleich zu Windkraftanlagen eine größere Palette von Werkstoffen insbesondere aus dem Bereich der rost- und säurebeständigen Stähle sowie höhere Prozesstemperaturen zum Tragen, die für Windkraftanlagen keine Relevanz haben. KW - Offshore-Power-to-X-Anlagen KW - Maritime Korrosion KW - Korrosionsschutz PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-658008 DO - https://doi.org/10.34657/32991 SP - 1 EP - 25 AN - OPUS4-65800 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Witt, Julia T1 - Electrocatalyticperformance and stabilityofmulti-principalelement alloys (MPEAs) N2 - Accurately distinguishing oxygen evolution reaction (OER) currents from anodic metal dissolution is essential for accurately evaluating metal electrocatalysts, as both processes often overlap in the transpassive potential region.1,2 This study explored multi-principal element alloys (MPEAs) as a pathway toward sustainable electrocatalysis by reducing reliance on noble and critical metals. CrCoNi and CrMnFeCoNi alloys are used as model systems to understand how complex compositions behave when OER and dissolution occur simultaneously, providing a benchmark for designing Co-reduced/free variants within the FeCrNi MPEA family. To quantitatively separate these pathways, we employ an integrated operando approach: tip-substrate voltammetry in scanning electrochemical microscopy (TSV-SECM) for spatially resolved O2 detection, ICP-MS and UV-Vis spectroscopy for dissolution quantification and chromium speciation, and in-situ electrochemical AFM (EC-AFM) to identify the onset of corrosion and track nanoscale surface evolution. Converting dissolution data into electrochemical charge enables a precise attribution of transpassive currents to either OER or metal dissolution. To further assessmass-transport effects, MPEAs were examined using rotating disk electrode (RDE) methods. Controlled hydrodynamics separate kinetic from diffusion-limited regimes and reveal how dissolution rates, passive-film behavior, and OER activity respond under flow conditions. Overall, this methodology provides a robust platform for reliably distinguishing catalytic OER performance from corrosion processes while guiding the design of next-generation electrocatalysts that minimize or eliminate Co and other critical and noble metals. Extending these insights to FeCrNi-based systems offers new opportunities for sustainable, high-performance materials capable of operating under technologically relevant anodic conditions. T2 - Materials for Sustainable Development Conference (MATSUS26) CY - Barcelona, Spain DA - 23.03.2026 KW - Multi-principal elemt alloy (MPEAs), Corrosion, Electrocatalysis, Scanning electrochemical miscroscopy (SECM) PY - 2026 AN - OPUS4-65791 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Riechers, Birte A1 - Pekin, Thomas C. A1 - Luo, Xin-Yu A1 - Sun, Yonghao A1 - Koch, Christoph T. A1 - Derlet, Peter M. A1 - Maaß, Robert T1 - Spatial distribution and connectivity of medium-range order signatures in a metallic glass probed with simulated and experimental 4DSTEM N2 - challenge. Here, we assess the statistical signature of local diffraction symmetries and their spatial distribution obtained with transmission electron microscopy in both experimentally cast Pd-based MGs and simulated binary model glasses. A detailed analysis of diffraction symmetries from the model glass shows that microstructural coarsening is dominated by icosahedra and Frank–Kasper polyhedra. While symmetries for these motifs are less significant for the laboratory-cast Pd-based glass, clear signatures of symmetry-cluster coarsening as a function of relaxation state are observed in both experiments and simulations, without any indications for crystallization. These findings give support for a qualitatively similar evolution of a glassy microstructure at the medium-range order length scale during glass relaxation. KW - Metallic glass KW - TEM KW - Molecular dynamics simulations KW - Glass structure PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-657772 DO - https://doi.org/10.1016/j.jallcom.2026.186631 SN - 0925-8388 VL - 1058 SP - 1 EP - 10 PB - Elsevier B.V. AN - OPUS4-65777 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - GEN A1 - Bayat, Mehmet Emin A1 - Nandayapa, Edgar R. A1 - Tiebe, Carlo A1 - Unger, Eva L. A1 - List-Kratochvil, Emil J. W. T1 - Raw data from: "An operando spectroscopic examination of the influence of trace humidity on interdigital back contact metal halide perovskite solar cells" N2 - Controlling trace humidity is vital for both the fabrication and long-term stability of metal halide perovskite (MHP) solar cells. Relevant humidity levels are typically below 10 ppmV, especially in glovebox-based processing and in well-encapsulated devices. Even minute amounts during fabrication can influence crystallization, introducing defects and lowering efficiency. Over time, humidity accelerates degradation of the perovskite layer and internal interfaces, ultimately reducing operational lifetime. Probing these effects at low concentrations under operando conditions is therefore essential for advancing device performance and durability. In this work, we employed a high-precision transfer standard dew point hygrometer to investigate humidity levels between 5 and 35 ppmV in non-encapsulated MHP solar cells. To permit unobstructed water migration during operation, we fabricated interdigital back contact devices. Operando measurements revealed water transport through the perovskite layer and enabled quantification of outgassing. Under trace-humidified conditions, devices exhibited initial charge-carrier quenching, followed by gradual recovery. Notably, the photocurrent response to humidified nitrogen demonstrated that the MHP layer behaves fully reversibly within the explored timescale and across the investigated humidity levels and conditions. These findings establish a systematic operando framework for examining extrinsic stressors in perovskites and highlight opportunities for assessing passivation strategies. KW - Metal halide perovskite PY - 2026 DO - https://doi.org/10.5281/zenodo.18600851 PB - Zenodo CY - Geneva AN - OPUS4-65757 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Hübner, Martin T1 - (K)ein explosives Thema? - Schweißen an und auf zukünftigen Wasserstoffpipelines im Betrieb unter Druckgasfluss N2 - Das Schweißen an druckführenden Leitungen im Betrieb ist beim Erdgas-Fernleitungsnetz Stand der Technik, beispielsweise beim Setzen von Abgängen durch „Hot-Tapping“. Diese Technik wird auch beim zukünftigen Wasserstoff-Kernnetz eine bedeutende Rolle spielen. Verfahrensbedingt ist daher eine bestimmte Wasserstoffaufnahme während des Schweißens unvermeidbar. Aus diesem Grund werden derzeit in mehreren Forschungsprojekten wie umfassende Erkenntnisse zum Schweißen an Rohrleitungen unter Druckwasserstoff gewonnen. Die grundsätzliche Übertragbarkeit des „Hot-Tapping“ auf zukünftige Wasserstoff-Rohrleitungen wurde bereits bestätigt (u. a. DNV-Projekt und HyTap). Allerdings besteht allein das zukünftige Wasserstoff-Kernnetz in Deutschland aus einer Vielzahl von Bestands- und Neuwerkstoffen mit unterschiedlichen Festigkeiten, Durchmessern und Wandstärken. Für diese ist eine umfassende Betrachtung notwendig. In diesem Bereich leistet das Projekt H2-SuD wesentliche Beiträge, insbesondere zur Frage der Anpassung der Mindestwandstärke für sicheres Schweißen. Hierzu bieten die Demonstratoren eine ideale Grundlage zum Screening vieler Schweißparameter-Werkstoff-Kombinationen. Eine erhöhte Wasserstoffkonzentration beim Schweißen wurde experimentell belegt (DNV-Projekt und H2-SuD), allerdings im allgemein nicht als kritisch erachteten Bereich. Zudem wurde eine Wasserstoffversprödung der Schweißnaht während des Schweißens an druckwasserstoffführenden Demonstratoren bisher nicht beobachtet. Dies liegt u.a. an den mechanischen Eigenschaften der Rohrleitungswerkstoffe (gute Dehnfähigkeit, auch im geschweißten Zustand). T2 - Vortragsreihe des Bezirksverbandes Berlin des Deutschen Verbandes für Schweißen und verwandte Verfahren (DVS) e.V. CY - Berlin, Germany DA - 25.03.2026 KW - Wasserstoff KW - Rohrleitung KW - Schweißen KW - Demonstrator KW - Bauteilprüfung PY - 2026 AN - OPUS4-65774 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rhode, Michael T1 - Praktikable Prüfung der Wasserstoffverteilung in Mehrlagenschweißungen in Anlehnung an die DIN EN ISO 3690 N2 - Das Forschungsvorhaben adressiert eine zentrale Lücke und damit einhergehende Einschränkung für geschweißte hochfeste Werkstoffe in der aktuellen Normung: Die DIN EN ISO 3690 erlaubt ausschließlich die Bestimmung des diffusiblen Wasserstoffs in einlagigen Prüfraupen und bildet damit die realen Bedingungen in mehrlagigen Schweißnähten hochfester Stähle nicht ab. Durch das mehrfache wiederholte Aufwärmen wird die eingebrachte Wasserstoffkonzentration deutlich unter die konservativen, einlagigen Prüfraupen bereits während des Schweißens abgesenkt. Hierzu fehlt jedoch eine einfache, experimentelle Methoden, um die tatsächliche lokale lagenabhängige bzw. globale Wasserstoffverteilung quantifizieren zu können. Das Vorhaben entwickelt daher erstmals eine Versuchsmethodik, der reale Diffusions- und Entgasungsbedingungen von Mehrlagenschweißungen experimentell reproduziert. Dadurch werden die Nachteile der ISO 3690 (einlagige Prüfraupe, konservative Bewertung) aufgehoben und mit dem Hauptvorteil (robuste, einfache Handhabung) kombiniert. Durch gezielte Variation von Wärmeführung, Zwischenlagentemperaturen und Wasserstoffangebot werden lokale und globale Wasserstoffverteilungen quantifiziert. Ergänzt durch ein numerisches Diffusionsmodell entsteht ein skalierbares Bewertungswerkzeug, das die experimentellen Daten generalisiert und auf reale Schweißnähte überträgt. Die Ergebnisse ermöglichen: (1) eine realitätsnahe Bewertung verbleibender Wasserstoffgehalte, Kaltrisssicherheit, damit die (2) die mögliche Ausweitung der HD Klassifizierung hochfester Schweißzusätze, und (3) die Beurteilung der Effektivität und Notwendigkeit von Wärmenachbehandlungs-maßnahmen (wie „Wasserstoffarmglühen“). T2 - Sitzung des NA 092-00-05 GA Gemeinschaftsarbeitsausschuss NAS/NMP: Zerstörende Prüfung von Schweißverbindungen (DVS AG Q 4/Q 4.1) CY - Berlin, Germany DA - 24.03.2026 KW - Schweißen KW - Wasserstoff KW - ISO 3690 KW - Prüfung KW - Mehrlagennaht PY - 2026 AN - OPUS4-65784 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Falkenhagen, Jana A1 - Beskers, Timo. F. A1 - Myxa, Anett A1 - Pursch, Matthias T1 - Round-robin test for size exclusion chromatography – Data summary N2 - Size exclusion chromatography (SEC or GPC) is one critical component of polymer analysis to meet the increasing requirements in regulatory context – namely, determination of Mn, as well as oligomers of less than 500 g mol-1 and 1000 g mol-1. The underlying test methods (OECD 118/119 and DIN EN ISO 13885 1 to 3) provide a framework for SEC measurements; however, they lack sufficient specificity to obtain accurate results. Previous SEC round robin tests were mostly performed on homopolymers and did not collect data on oligomer contents. A new round robin test was initiated and conceptualized within the Task force “Method Evaluation for Polymer REACh (MeEP)”, an initiative of “Industrieforum Analytik” within the German Chemical Society (GDCh). Samples for this study were selected to represent both easy benchmark polymers as well as real-life, industry-relevant polymer materials. Data collection focused on the regulatory requirements. Distribution of samples, gathering of individual results and evaluation were carried out by BAM. A data summary as initial result is reported here. Further evaluation and interpretation are a part of ongoing research. KW - Size exclusion chromatography KW - Polymers KW - Oligomer content KW - Round-robin test PY - 2026 DO - https://doi.org/10.26272/opus4-65587 SP - 1 EP - 84 PB - Bundesanstalt für Materialforschung und -prüfung (BAM) CY - Berlin AN - OPUS4-65587 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kromm, Arne T1 - Effect of a High-Performance Modified Spray Arc MAG Process on Load-Oriented Repair of Old Steel Structures N2 - Steel structures erected in the late 19th and early 20th centuries still constitute a substantial part of today’s technical infrastructure. A significant proportion of bridge and engineering structures have been in service for more than 80 or even 100 years and are subjected to continuously increasing traffic volumes, axle loads, and dynamic actions. In view of these rising service demands, load-oriented and structurally adequate repair strategies are essential to ensure long-term structural integrity while preserving the existing building stock in a sustainable manner. As historical steel constructions were predominantly designed for riveted or bolted joints, the subsequent implementation of welded repair or strengthening measures represents a particular challenge. In addition to the specific material characteristics of old mild steels, welding-induced residual stresses and microstructural alterations must be carefully considered, as they can significantly affect load-bearing capacity and the overall structure performance. Consequently, repair concepts must not only restore geometry but also be adapted to the actual stress conditions and service requirements of the structure. Against this background, the present study investigates MAG welding trials on mixed joints between old and modern structural steels. The groove opening angle was systematically varied between 50° and 30° in order to analyse the influence of joint geometry on weld metal volume, heat input, and the resulting residual stress state. Furthermore, advanced high-performance arc processes, such as a modified spray arc mode, were applied to enable controlled and reduced heat input. The objective is to minimise welding-induced residual stresses through process and joint design optimisation, thereby providing a technically sound and load-oriented repair strategy for existing old steel structures suitable for long-term service. T2 - IIW Intermediate Meeting, Commission II-E CY - Bangkok, Thailand DA - 16.03.2026 KW - Historic mild steel KW - Weldability KW - High strength steel PY - 2026 AN - OPUS4-65745 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Avila Calderon, Luis Alexander T1 - On the role of the manufacturing-induced cell structure in laser-powder-bed-fused stainless steel 316L during cyclic plastic deformation N2 - The room temperature cyclic plastic deformation behavior of stainless steel 316L produced by laser powder bed fusion and heat treated to two microstructural conditions was investigated in strain-controlled incremental-step-test low-cycle fatigue experiments. The heat treatments were performed at 450 °C for 4 h and at 900 °C for 1 h. The lower temperature heat treatment retains the cell structure present in the as-built material. The higher temperature heat treatment leads to disappearance of the cell structure and a decreased proof strength. Both investigated heat treatment conditions exhibited cyclic softening. In the condition heat treated at 900 °C for 1 h, the ability of the cell structure to act as barrier against plastic deformation when cyclically strained is degraded, which is reflected in the reduction of the cyclic yield strength. In that same condition, the cyclic softening was less pronounced. The presence or absence of the manufacturing-induced cell structure seems to determine the slip mode. When present, the microstructural evidence points to a planar slip behavior. After heat treatment at 900 °C for 1 h, which led to its dissolution, microstructural investigations revealed a wavy slip behavior, which has been also reported for the conventionally manufactured 316L counterpart [1]. In this case, the formation of low-energy dislocation structures acts as softening agent. T2 - Additive Manufacturing 2026 CY - Kassel, Germany DA - 25.03.2026 KW - AGIL KW - Additive Fertigung KW - Low-Cycle-Fatigue KW - 316L KW - Mikrostruktur PY - 2026 AN - OPUS4-65746 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bayat, Mehmet Emin A1 - Nandayapa, Edgar R. A1 - Tiebe, Carlo A1 - Unger, Eva L. A1 - List-Kratochvil, Emil J. W. T1 - An operando spectroscopic examination of the influence of trace humidity on interdigital back contact metal halide perovskite solar cells N2 - Controlling trace humidity is vital for both the fabrication and long-term stability of metal halide perovskite (MHP) solar cells. Relevant humidity levels are typically below 10 ppmV, especially in glovebox-based processing and in well-encapsulated devices. Even minute amounts during fabrication can influence crystallization, introducing defects and lowering efficiency. Over time, humidity accelerates degradation of the perovskite layer and internal interfaces, ultimately reducing operational lifetime. Probing these effects at low concentrations under operando conditions is therefore essential for advancing device performance and durability. In this work, we employed a high-precision transfer standard dew point hygrometer to investigate humidity levels between 5 and 35 ppmV in non-encapsulated MHP solar cells. To permit unobstructed water migration during operation, we fabricated interdigital back contact devices. Operando measurements revealed water transport through the perovskite layer and enabled quantification of outgassing. Under trace-humidified conditions, devices exhibited initial charge-carrier quenching, followed by gradual recovery. Notably, the photocurrent response to humidified nitrogen demonstrated that the MHP layer behaves fully reversibly within the explored timescale and across the investigated humidity levels and conditions. These findings establish a systematic operando framework for examining extrinsic stressors in perovskites and highlight opportunities for assessing passivation strategies. KW - Metal halide perovskite KW - IBC solar cells KW - In operando KW - Extrinsic stressors KW - Fabrication and encapsulation KW - Trace humidity KW - Two-site Stern-Volmer KW - Charge-carrier quenching PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-657560 DO - https://doi.org/10.1039/D6TA01295G SP - 1 EP - 16 PB - The Royal Society of Chemistry CY - London AN - OPUS4-65756 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Serrano-Munoz, Itziar A1 - Dufrenoy, Philippe A1 - Magnier, Vincent T1 - Rationalizing the microstructure interplay in the thermal conductivity of a metal matrix composite via 3D imaged-based finite element modeling N2 - The thermal performance of metallic brake lining materials plays a decisive role in the safety and efficiency of high-speed railway braking systems. In this study, a combined experimental–numerical methodology is developed to rationalize the influence of microstructural constituents on the effective thermal conductivity of a sintered metal matrix composite (MMC) brake lining. Laser Flash Analysis (LFA) is first employed to determine the thermal conductivity of some individual constituents as well as that of reference composites. X-ray CT (XCT) provides three-dimensional reconstructions of the microstructure that are subsequently used to generate realistic image-based finite element meshes. The unknown thermal conductivities of the graphite particles are identified through a Finite Element Model Updating (FEMU) scheme, where numerical predictions of the effective conductivity are iteratively matched to LFA measurements. These findings highlight the strong anisotropy of graphite particles and their favored orientation after compaction, which governs heat transport pathways. Moreover, the presence of intra-, inter-, and inter-connectivity porosity within and around the graphite is shown to significantly reduce the transverse conductivity, rationalizing the discrepancy between the FEM predictions and experimental values. Overall, the proposed approach demonstrates how combining LFA, XCT and FEMU enables the identification of constituent-level conductivities and provides new insights into the microstructure/thermal-property relationships of MMC brake linings. KW - Brake lining material KW - Thermal conductivity KW - Graphite particles KW - Laser flash analysis (LFA) KW - X-ray computed tomography (XCT) KW - 3D finite element model updating (FEMU) PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-657756 UR - https://www.sciencedirect.com/science/article/pii/S0017931026004114?via%3Dihub DO - https://doi.org/10.1016/j.ijheatmasstransfer.2026.128735 SN - 0017-9310 VL - 264 SP - 1 EP - 14 PB - Elsevier Ltd. AN - OPUS4-65775 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Meng, Xiangmeng A1 - Bachmann, Marcel A1 - Yang, Fan A1 - Rethmeier, Michael T1 - Porosity prediction in laser beam welding with a multimodal physics-informed machine learning framework N2 - Laser beam welding (LBW) of metallic components is a knowledge‑intensive manufacturing process whose quality depends on the complex multi‑physics. However, its engineering application is often hindered by the occurrence of porosity defects. Achieving a thorough understanding and reliable prediction of porosity defects remains difficult because it demands robust representation and reasoning over nonlinear and hard‑to‑observe physical information. In this study, we propose an integrated multimodal physics-informed machine learning (PIML) framework with the help of multi-physical modelling and experimental data to predict the porosity defects in laser beam welding of aluminum alloys. The whole framework contains a multimodal PIML model for predicting the porosity ratio and an ML-based estimator for relevant physical information. By utilizing the scalar welding parameters and high-dimensional physical information (probability of keyhole collapses, cumulative existing time of collapses, and molten pool geometry) as inputs, the multimodal PIML model shows great superiority in predicting the porosity ratio, with a reduction of the mean square error by 45%, compared with the ML model trained only with welding parameters. The ML-based estimator constructed with an encoder‐decoder architecture can accurately reproduce the critical physical information within a timeframe of seconds. By integrating these two ML models, the proposed framework advances engineering informatics by offering a scalable, physics-knowledge‑centric solution for fast and accurate porosity prediction in LBW manufacturing. KW - Laser beam welding KW - Porosity defect KW - Physics-informed machine learning KW - Multimodal model KW - Simulation PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-657589 DO - https://doi.org/10.1016/j.aei.2026.104611 SN - 1474-0346 VL - 74 SP - 1 EP - 12 PB - Elsevier Ltd. AN - OPUS4-65758 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koerdt, Andrea T1 - Mikrobielle Einflüsse auf Wasserstoffspeicherung: Materialien, Abbauprozesse und Teststrategien N2 - Wasserstoff gilt als Schlüsseltechnologie für die Energiewende – doch seine sichere Anwendung stellt neue Anforderungen an Technik, Infrastruktur und Personal. Die Veranstaltung „H₂ Sicherheit“ bietet eine umfassende Plattform, um sich über die sicherheitsrelevanten Aspekte von Wasserstoff zu informieren und praxisnahe Lösungen kennenzulernen. Expert:innen aus Forschung, Industrie und Netzbetrieb geben Einblicke in aktuelle Entwicklungen, Herausforderungen und Best Practices. Fokus dieser Präsentation war der Mikrobielle Einfluss bei der unterirdischen Speicherung von Wasserstoff und das neuartige Testsystem (MISTRAL) T2 - DVGW- H₂ Sicherheit CY - Online meeting DA - 24.03.2026 KW - Wasserstoff KW - Unterirdische geologische Formationen KW - MISTRAL KW - MIC KW - Hochdruckbehälter KW - Biokorrosion PY - 2026 UR - https://www.dvgw-kongress.de/veranstaltungen/gas/h2-sicherheit#collapse-8103 AN - OPUS4-65810 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -