TY - CONF A1 - Thünemann, Andreas T1 - Structure Analysis of Functional Hydrogels with Small-Angle X-ray Scattering (SAXS) N2 - Hydrogel properties are largely determined by their network structure. Here, we report on the capabilities of SAXS methods for characterizing polymer-network gels. SAXS provides rich insight into different types and levels of nanostructural inhomogeneities in these soft matter materials. The structure analysis of alginate hydrogels, typically utilized in tissue engineering applications, will be discussed in detail. T2 - Polydays 2024 CY - Berlin, Germany DA - 30.09.2024 KW - SAXS KW - Small-angle X-ray scattering KW - Polymer KW - Gel PY - 2024 AN - OPUS4-61184 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Shasmal, Nilanjana T1 - Effects of Direct femtosecond laser writing on chloroborosilicate glasses doped with Eu3+/Eu2+ and CdS quantum dots N2 - Femtosecond (fs) direct laser writing (DLW) is a promising technique for developing nano-inhomogeneous materials with advanced optical properties and for fabricating novel photonic devices such as integrated waveguides, ultrafast optical switches, phase plates, and 3D optical memory. In this study, DLW was applied to chloroborosilicate glasses that were singly and co-doped with Eu and CdS quantum dots (QDs). The glasses were laser-treated within a very narrow range of experimental conditions, resulting in laser-inscribed sites exhibiting enhanced emission, similar to the glass-ceramics crystallized from the as-prepared glass. In the regions crystalized by DLW a significant reduction of Eu3+ to Eu2+ was verified by photoluminescence spectroscopy. However, the characteristics of the emission bands of Eu2+ changed markedly in the laser-treated sites as compared to the emission spectra of the same glass crystallized by heat treatment. A considerable redshift and splitting of the emission band were observed, attributed to changes in the surrounding environment of the rare earth (RE) ions which was, in turn, attributed to an alteration in the coordination number of Ba2 + and/or Eu2+ as a result of the high-power laser treatment. Although there was an issue with homogeneity of the glass in the micro-level, which restricts some of the aspects of the DLW, these findings suggest the potential for structural modifications through laser treatment, which could be harnessed to create new functionalities for advanced optical applications. T2 - ICG 2025 (27th International Congress on Glass) CY - Kolkata, India DA - 20.01.2025 KW - Femtosecond direct laser writing KW - DLW KW - CdS quantum dots KW - Eu/CdS co-doped glass PY - 2025 AN - OPUS4-65285 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Emmerling, Franziska A1 - Michalchuk, Adam A1 - Bhattacharya, Biswajit A1 - Rodríguez Sánchez, Noelia A1 - Gugin, Nikita T1 - Advancing sustainable synthesis through in situ monitoring and industrial scale-up of mechanochemical processes N2 - Mechanochemistry has emerged as a powerful approach for sustainable materials synthesis and processing, with significant potential to meet the UN Sustainable Development Goals. This presentation will highlight our recent advancements in understanding, monitoring, and scaling-up mechanochemical transformations, focusing on the balance between fundamental understanding of reaction mechanisms and its practical applications in energy storage and energy transfer materials. Our research has made significant strides in elucidating the fundamental mechanisms of mechanochemical reactions. We have investigated delayed polymorphism under mechanochemical conditions, revealing new insights into the interplay between mechanical impact, thermal effects, and structural transformations in molecular crystals. By employing variable temperature ball milling, we have demonstrated unprecedented control over polymorphic forms in organic cocrystals, opening new avenues for tailoring material properties. A central focus of our work has been the development and application of time-resolved in situ monitoring techniques for mechanochemical processes. Our research on real-time synchrotron X-ray diffraction has enabled unprecedented insights into reaction pathways and kinetics. Recently, we have successfully applied energy-dispersive X-ray diffraction for time-resolved in situ monitoring of reactive extrusion, marking a significant step towards ‘lighting up’ industrial-scale mechanochemistry. Bridging fundamental understanding with practical applications, we have explored the mechanochemical synthesis of functional materials for energy storage and transfer, making process in the mechanochemical synthesis of highly proton-conductive metal phosphonates, demonstrating the potential of mechanochemistry to manufacture advanced materials for energy applications. Addressing the challenges of industrial scale-up, we have investigated the role of solvent polarity in mechanochemical reactions, providing valuable guidance for optimizing organic syntheses such as the Knoevenagel condensation. This work contributes to our broader efforts to develop more efficient and sustainable chemical manufacturing processes. Looking to the future, we will discuss emerging directions in mechanochemistry, including the development of continuous flow processes and the integration of machine learning approaches for reaction prediction and optimization. As we anticipate the next decade of research, we envision mechanochemistry playing an increasingly crucial role in sustainable chemical manufacturing and materials processing, with far-reaching implications for addressing global energy and environmental challenges. T2 - Mech’cheM 2025: New forces in Mechanochemistry Conference CY - Montpellier, France DA - 04.06.2025 KW - Phosphonates KW - Biocomposites PY - 2025 AN - OPUS4-64845 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Emmerling, Franziska A1 - Michalchuk, Adam A1 - Bhattacharya, Biswajit A1 - Rodríguez Sánchez, Noelia A1 - Gugin, Nikita T1 - Mechanochemical innovations for sustainable synthesis of framework materials and industrial scaleup N2 - Mechanochemistry has emerged as a powerful approach for sustainable materials synthesis and processing, with significant potential to meet the UN Sustainable Development Goals. This presentation will highlight our recent advancements in understanding, monitoring, and scaling-up mechanochemical synthesis of framework materials, focusing on the balance between fundamental understanding of reaction mechanisms and its practical applications in energy storage and energy transfer materials. A central focus of our work has been the development and application of time-resolved in situ monitoring techniques for mechanochemical processes. Our research on real-time synchrotron X-ray diffraction has enabled unprecedented insights into reaction pathways and kinetics. Recently, we have successfully applied energy-dispersive X-ray diffraction for time-resolved in situ monitoring of reactive extrusion, marking a significant step towards ‘lighting up’ industrial-scale mechanochemistry. Bridging fundamental understanding with practical applications, we have explored the mechanochemical synthesis of functional materials for energy storage and transfer, making process in the mechanochemical synthesis of highly proton-conductive metal phosphonates, demonstrating the potential of mechanochemistry to manufacture advanced materials for energy applications. T2 - 17. international-conference für Materialchemie CY - Edinburgh, United Kingdom DA - 07.07.2025 KW - MOF KW - Synchrotron KW - ZIF PY - 2025 AN - OPUS4-64841 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - George, Janine T1 - Crossing Scientific Disciplines with Materials Informatics:� From Atoms to Algorithms N2 - Within this talk, I introduced students from Physics to Materials Informatics. To provide a context for this research, I have introduced the students to BAM and its tasks. I then started to introduce our activity field materials design, including materials acceleration platforms. Then, I explained how simulations speed up the materials searches as parf of materials acceleration platforms. T2 - jDPG Jena Meeting - Poland exchange CY - Jena, Germany DA - 26.02.2026 KW - Automation KW - Machine Learning KW - Materials Design KW - Batteries KW - Workflows PY - 2026 AN - OPUS4-65589 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ciornii, Dmitri T1 - Validation of microplastics detection methods and proficiency testing: Suitable microplastic reference materials for interlaboratory comparison N2 - Since microplastics (MPs) can be found everywhere and are becoming a problem of high concern, it is necessary to understand their physico-chemical properties. To obtain reliable analytical data a set of validated methods for sampling, sample preparation, detection, and data evaluation are needed. To meet these needs an interlaboratory comparison (ILC) with 84 participants worldwide has been organized under the international pre-standardisation platform VAMAS (www.vamas.org/twa45/) as Project 2 “Development of standardized methodologies for characterisation of microplastics with microscopy and spectroscopy methods” within the Technical Working Area TWA 45 “Micro and Nano Plastics in the Environment”. In this ILC thermo-analytical methods (Py-GC/MS and TED-GC/MS) and vibrational methods (µ-Raman and µ-FTIR) have been tested and compared by providing a set of microplastic representative test materials and measurement protocols developed at BAM. The defined measurands were: particle number concentration, particle size distribution (PSD), and polymer identity and mass content. To increase the statistical quality, 6 samples were shipped together with blank samples. Hence, the ILC provides information on precision and accuracy of the results obtained with different methods as well as strengths and limitations of the proposed protocols. T2 - SETAC 34th Meeting CY - Seville, Spain DA - 05.05.2024 KW - ILC KW - Microplastic KW - Method validation KW - Stakeholder KW - Reference materials KW - Polyethylene KW - Polyethylene Terephtalate PY - 2024 AN - OPUS4-60039 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Emmerling, Franziska A1 - Michalchuk, Adam A1 - Casali, Lucia A1 - May, Anastasia T1 - Real-Time Monitoring and Temperature Control for Optimized Polymorph Engineering N2 - Integrating real-time monitoring with precise temperature control and mechanochemical processing represents a transformative approach to the controlled engineering of polymorphic forms in molecu-lar solids. Combining these methodologies overcomes the limitations of traditional solution-based or purely thermal approaches, enabling access to metastable or otherwise elusive polymorphs under milder and more sustainable conditions. Recent studies have shown that mechanochemical trans-formations proceed through distinct kinetic stages, including prolonged induction periods that can be tuned by adjusting the mechanical energy input[1]. These induction periods are associated with pro-cesses of mechanical activation, such as the accumulation of defects and increased surface energy, which lower the effective energy barriers for polymorphic transitions. Crucially, it is the total accumu-lated mechanical energy, rather than the duration or intensity of milling alone, that dictates the onset of polymorphic conversion, offering a new dimension of kinetic control[2-5]. Variable temperature ball milling reveals that the temperature required to induce polymorphic trans-formations can be significantly lower than under conventional thermal methods. For instance, tran-sitions that typically require high temperatures under equilibrium conditions can be achieved at sub-stantially lower temperatures in the presence of mechanical activation. This has been demonstrated in cocrystal systems such as nicotinamide-pimelic acid and isonicotinamide-glutaric acid, where the transition temperature was lowered by up to 25°C[2,3]. Real-time, in situ powder X-ray diffraction and temperature monitoring are essential for capturing transient phases and elucidating the interplay between thermal and mechanical effects. This confirms that combining mechanical energy with con-trolled temperature not only accelerates transformation kinetics, but also expands the accessible polymorphic landscape [2,3]. Collectively, these advances underscore the potential of real-time monitored, temperature-controlled mechanochemistry as a robust platform for the selective design and manufacturing of polymorphs. This approach provides unprecedented control over solid-state reactivity and opens new avenues for the sustainable and targeted engineering of functional materials and pharmaceuticals. T2 - 13th Bologna´s convention on Crystal Forms - CF@Bo n.13 University of Bologna CY - Bologna, Italy DA - 07.09.2025 KW - Plymorhism KW - Pre-activation PY - 2025 AN - OPUS4-64839 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Production of small micro- and nanoplastic reference materials supporting harmonization and standardization N2 - The MICROPLASTICdays at Ljubliana, Slowenia, were organized in cooperation with the PRIORITY cost action. The topic has been reference materials this time. The talk gives an idea of the preparation of reference materials in micro- and nanoplastic topic to support standardisation and regulation. It defines the term of micro-and nanoplastics and presents different case studies and critical attributes to the production depending on the enduser needs. T2 - MICROPLASTICdays CY - Ljubljana, Slovenia DA - 25.03.2025 KW - Microplastics KW - Nanoplastics KW - Reference materials PY - 2025 AN - OPUS4-62801 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Pauw, Brian Richard T1 - NeXus at the core of the HExX-lab N2 - Through bottom-up, comprehensive digitalisation of all aspects of an experiment, the HEX-lab improves the trustworthiness (traceability, reproducibility, quality) of scientific findings. The five main parts that make up a materials science experiment, i.e. Sample preparation, Measurements, Processing, Analysis, and Interpretation, each have been addressed in thorough and unique ways in this lab, building up a foundation for a wide range of materials science collaborations. Improvements span the spectrum. Hardware developments include new sample environments and stages, such as grazing incidence motion towers, electrochemistry cells and flow-through holders, electronic components such as safety interlocks and multipurpose I/O controllers, and liquid handling systems such as coolant flow cross-over systems. Software developments include: 1) a new comprehensive control system operating on both the RoWaN as well as the MOUSE allowing for full Python control and sequencing of all experimentation, 2) Automated scripts for instrument optimization, sample alignments and measurements, 3) revamped data pipelines and analysis software, standalone or launched as part of operations sequencing dashboards on servers, and 4) meticulously structured archival datafiles, fully documenting sample preparation, measurements, processing and analyses. These allow for holistic databases and dashboards to be constructed to investigate the links between synthesis parameters and resulting morphology. This presentation will highlight some of the tools and techniques developed and available in the HEX-lab over the years, from sample environments to overarching experiment and data organisation structures. T2 - Materials Science Core Facility Synergy Forum 2025 CY - Bremen, Germany DA - 26.02.2025 KW - Digitalization KW - Automation KW - HDF5 KW - Traceability KW - Data stewardship KW - Lab automation KW - Holistic science KW - Methodology PY - 2025 AN - OPUS4-62676 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wiesner, Yosri T1 - Reference material candidates for Microplastic analysis N2 - Microplastic reference material is required for validation and harmonization purposes. This includes the analysis of the pure polymer particles and the validation of the respective measurement methods. In addition, there is the harmonization of different laboratories. On the other hand, sample preparation methods must be validated and harmonized with regard to their recovery and subsequent analysis in the respective matrices. For this purpose, we produce reference material candidates in the form of tablets with different mass fractions and particle numbers of polyethelene terephthalate. In the presentation first measurement results by µ-Raman, µ-FTIR, pyrolysis-GC-MS and TED-GC/MS will be presented. T2 - SETAC Europe 34th Annual Meeting CY - Seville, Spain DA - 05.05.2024 KW - Reference material KW - Microplastics KW - PlasticTrace PY - 2024 AN - OPUS4-60019 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -