TY - CONF A1 - Schoknecht, Ute T1 - Leaching und Transformation von Bioziden aus Fassadenfarben N2 - Anhand von Beobachtungen aus Labor- und Freilandversuchen wurde dargestellt, wie Wasserkontakt und Strahlung die Auslaugung und Transformation der Wirkstoffe Diuron und Terbutryn beeinflussen. Auf Optionen zur modellhaften Darstellung dieser Prozesse wurde kurz eingegangen. T2 - Optimierung und Minimierung des Biozideinsatzes in Baustoffen CY - Online meeting DA - 09.02.2022 KW - Leaching KW - Transformation KW - Biozid KW - Fassadenfarbe PY - 2022 AN - OPUS4-55273 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schoknecht, Ute T1 - The Impact of Weather Conditions on Biocides in Paints N2 - Aim. The European biocidal products regulation requires environmental risk assessments for biocidal products under service conditions. This is only possible, if processes that lead to biocide emissions into the environment are understood and can be reasonably predicted. Actual emissions due to leaching result from different processes that are affected by material properties and environmental conditions. Transformation of biocides can affect emissions considerably. Leaching and possible transformation of the film preservatives carbendazim, diuron, OIT and terbutryn in paints was observed under laboratory and field conditons in order to investigate the influence of different factors, e.g. water contact and radiation on biocide emissions. The paints contained either white titanium dioxide or a red iron oxide pigment to check whether pigments affect leaching processes. Methods. Test specimens of a water-based styrene acrylic dispersion paint on glass were exposed to UVA-radiation in a UV weathering device and/or exposed to water contact by immersion events on the basis of the European standard EN 16105. Plywood panels were coated and exposed to natural weather conditions in a semi-field experiment. Concentrations of biocides and transformation products were analysed in leachates from laboratory tests, runoff samples and remaining coatings. Results. The impact of weathering conditions on transformation processes differs for the investigated active substances. Water contact, radiation as well as pigments in the paints determine the pattern and amount of transformation products on coatings, leachates and runoff water. Observations from laboratory and field experiments were compared. It proved that results from laboratory tests support understanding of data from field experiments. Detailed knowledge on the fate of active substances under environmental conditions supports manufacturers to develop safe applications of film preservatives and authorities to evaluate its environmental impact. T2 - European Technical Coatings Congress 2022 CY - Kraków, Poland DA - 12.07.2022 KW - Paints KW - Biocides KW - Transformation KW - Emission PY - 2022 AN - OPUS4-55274 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schoknecht, Ute A1 - Kalbe, Ute A1 - Happel, O. T1 - Combination of leaching tests with ecotoxicity and chemical analysis – lessons learnt N2 - The presentation describes analytical methods to characterize eluates from leaching tests and identify organic substances in leachates. Chances to obtain complementary information from ecotoxtests and chemical analysis are discussed. T2 - Workshop: Ecotoxicological evaluation of construction products – test results, implementation in Guidance, Technical Standards and Ecolabelling CY - Online meeting DA - 21.03.2022 KW - Leaching KW - Ecotoxicity KW - Construction products PY - 2022 AN - OPUS4-55276 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, Julia T1 - Light-dependent development in Botrytis cinerea N2 - Sunlight is an important environmental factor is almost all ecosystems by being a source of energy, information, and stress. All organisms must protect themselves from the harmful effects of light such as UV radiation, ROS accumulation, heat, and desiccation. Finally, light qualities and quantities can be used for decision making, timing and as guide for directed growth when they are sensed and transduced into intracellular signals. Botrytis cinerea and other plant pathogens infecting the sun-exposed parts of the plant must cope with the high light conditions the host plant seeks. Further they experience an altered light spectrum (‘green gap’) when they colonize shaded parts of the plant; it is depleted for blue and red light that is absorbed by the plant chlorophyll and enriched for green and far-red light that is reflected or transmitted by the plant tissue. As these ambient light conditions trigger the shade avoidance response in the plant, the pathogens may trigger their own ‘shading response’ such as the upregulation of virulence determinants and inoculum production. B. cinerea maintains a highly sophisticated light signaling machinery that senses different light qualities to trigger a variety of responses, that are protection, morphogenesis, positive and negative tropisms, and entrainment. These characteristics render B. cinerea a valuable model to enlighten the role of light in parasitic fungus-plant interactions and beyond. The vegetative mycelium – the core of all infection and developmental programs – is not visibly pigmented and thus considered to be sensitive to biotic and abiotic stresses. However, the vegetative hyphae have a very limited half-life and are usually restricted to the invasive growth phase in which they are protected from light by the plant tissue. Fast colonization of host tissues and by this proper nutrient acquisition enables the rapid formation of long-lasting reproduction structures (melanized conidiophores with conidia, sclerotia) on the surfaces of rotted plant tissues. Depending on the light and temperature conditions, conidiation or sclerotial development is initiated. Taken together, B. cinerea uses light-regulated signaling networks to avoid light whenever possible; for example, by minimizing the half-life of sensitive cells that are hiding in plant tissues and by scheduling critical steps such as conidiogenesis, conidial germination and penetration of plant tissues for the night. T2 - BotrySclero2022 CY - Avignon, France DA - 13.06.2022 KW - Fungus KW - Light KW - Stress KW - Melanin PY - 2022 AN - OPUS4-55248 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, Julia T1 - Fungi in extreme habitats: Lessons from the microcolonial black fungus Knufia petricola N2 - Fungi that share light-flooded habitats with phototrophs may profit from their excess photosynthetic products. But to cope with sunlight-associated stresses [e.g. high temperatures, UV radiation with associated DNA damage, accumulation of reactive oxygen species (ROS), desiccation and osmotic stresses] it is important for fungi to accurately sense and respond to changes in light. The genomes of black [dihydroxynaphthalene (DHN) melanin-containing] fungi from phyllosphere and exposed solid surfaces contain multiple photoreceptors (PRs). The plant pathogen Botrytis cinerea (Leotiomycetes) has a highly sophisticated photosensory and signalling system that helps to avoid light and to locate susceptible hosts. Rock-inhabiting Dothideomycetes and Eurotiomycetes including Knufia petricola possess equal numbers of PRs along with the same set of protective pigments. This similarity between black fungi from plant and rock surfaces suggests that photoperception and -regulation are important for fungi that receive nutrients through cooperation with phototrophs. T2 - Gordon Research Conference "Cellular and Molecular Fungal Biology" CY - Holderness, NH, USA DA - 26.06.2022 KW - Light KW - Stress KW - Photoperception KW - Pigments PY - 2022 AN - OPUS4-55249 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kirsch, Klemens A1 - Matschiavelli, N. A1 - Koerdt, Andrea A1 - Stumpf, T. T1 - Microbiologically Influenced Corrosion of Cast Iron Containers for High-Level Nuclear Waste Disposal N2 - Ductile and corrosion resistant cast iron is investigated as a potential container material to store high-level nuclear waste (HLW) in deep geological repositories (DGR) in claystone bedrock. The dynamic corrosion process is dependent on the conditions present in the DGR which are influenced and/or controlled by geochemical parameters (e.g., redox potential, pH, presence of and ionic concentration in (pore-)water), physical parameters (e.g., pressure), and the influence of metabolically active microorganisms. Cast iron corrosion will occur at the intersection of container and its decontaminable coating with the bentonite backfill material which contains natural microbial populations. The conditions in a DGR are simulated in microcosm experiments to investigate the impact of microbiologically influenced corrosion (MIC); the microcosms contain: B27 bentonite, synthetic pore water, N2 or N2-CO2 atmosphere, cast iron coupons, as well as the bacterium Desulfosporosinus burensis (isolated from repository depth in Buré, France). Three coupon configurations will be used: untreated, coated with decontaminable coating, and coated with decontaminable coating which has been damaged to simulate possible damages. The microcosms will be examined for bio- and geochemical parameters, such as pH, redox potential, mineral phases, sulphate concentration, Fe(II):Fe(III), changes in microbial populations, and the corrosion process for formation of corrosion products, and potential microbial influence, after a 270-day incubation period at 25°C under anaerobic conditions. In subsequent experiments, the sorption behavior of lanthanides and actinides onto the membranes of viable cells and spores of D. burensis, as well as the surface of corroded cast iron coupons will be investigated. T2 - 8th International Workshop on Long-term Prediction of Corrosion in Nuclear Waste Systems 2022 CY - Baden, Switzerland DA - 21.06.2022 KW - Microbiologically influenced corrosion (MIC) KW - Cast iron KW - Nuclear waste disposal PY - 2022 AN - OPUS4-55154 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Resch-Genger, Ute A1 - Nirmalananthan-Budau, Nithiya A1 - Tavernaro, Isabella T1 - Engineered Nanomaterials- Novel Approaches for Risk Assessment and Safe-by-Design N2 - The overall interest in nanotoxicity, triggered by the increasing use of nanomaterials in the material and life sciences, and the synthesis of an ever increasing number of new functional nanoparticles calls not only for standardized test procedures1,2 and for efficient approaches to screen the potential genotoxicity of these materials, but also for standardized and validated methods for surface analysis. 4,5 The analysis and quantification of surface chemistry is hence in the focus of an increasing number of standardization organizations and interlaboratory comparisons with different analytical methods are being done.5 For the monitoring of nanomaterial synthesis and the fast assessment of the number of functional groups such as carboxyl and amino functionalities, which are very commonly used functionalities in the life sciences, simple and validated methods are needed that can be performed with common laboratory instrumentation. 5,6 Here we provide a brief overview of the ongoing research in division Biophotonics employing quantitative NMR (qNMR), conductometry, and colorimetric and fluorometric optical assays for the determination of the total and the accessible number of carboxyl and amino groups on differently sized polymer and silica nano- and microparticles.5-7 T2 - Workshop NanoRiskSD project CY - Berlin, Germany DA - 09.06.2022 KW - Nanoparticle KW - Surface analysis KW - Standardization KW - Quality assurance KW - Validation KW - qNMR KW - Silica KW - Polymer KW - Fluorescence KW - Assay KW - Conductometry KW - Method comparison KW - Analytical sciences PY - 2022 AN - OPUS4-54999 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bonse, Jörn A1 - Florian, Camilo A1 - Mezera, Marek A1 - Wasmuth, Karsten A1 - Richter, Anja A1 - Schwibbert, Karin A1 - Krüger, Jörg A1 - Müller, F. A. A1 - Gräf, S. T1 - A brief survey on open questions about laser-induced periodic surface structures N2 - The processing of laser-induced periodic surface structures (LIPSS) represents a simple and robust way for the nanostructuring of solids that allows creating a wide range of surface functionalities featuring applications in optics, tribology, medicine, energy technologies, etc. While the currently available laser and scanner technology already allows surface processing rates at the m2/min level, industrial applications of LIPSS are sometimes hampered by the complex interplay between the nanoscale surface topography and the specific surface chemistry. This typically manifests in difficulties to control the processing of LIPSS and in limitations to ensure the long-term stability of the created surface functions. This presentation aims to identify some unsolved scientific problems related to LIPSS, discusses the pending technological limitations, and sketches the current state of theoretical modelling. Hereby, it is intended to stimulate further research and developments in the field of LIPSS for overcoming these limitations and for supporting the transfer of the LIPSS technology into industry. T2 - E-MRS Spring Meeting 2022 CY - Online meeting DA - 30.05.2022 KW - Laser-induced periodic surface structures (LIPSS) KW - Surface functionalization KW - Industrial applications KW - Biofilm growth PY - 2022 AN - OPUS4-54929 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, Anja A1 - Buchberger, G. A1 - Stifter, D. A1 - Duchoslav, J. A1 - Hertwig, Andreas A1 - Bonse, Jörn A1 - Heitz, J. A1 - Schwibbert, Karin T1 - Reducing Escherichia coli adhesion to PET by modulating spatial periods of laser-induced surface nanoripples N2 - Using nanofiber-like cell appendages, secreted proteins and sugars, bacteria can establish initial surface contact followed by irreversible adhesion and the formation of multicellular biofilms. Here, the stabilizing extracellular biofilm matrix together with physiological changes on the single cell level leads to an increased resilience towards harsh environmental conditions, antimicrobials, the host immune response and established cleaning procedures. Persistent microbial adhesion on e.g., medical implants, in water supply networks or food-processing industry is often associated with chronic inflammation, nosocomial and foodborne infections, enhanced biofouling and product contamination. To prevent persistent microbial colonization, antibacterial surface strategies often target the initial steps of biofilm formation and impede adhesion of single cells before a mature biofilm is being formed. While chemical coatings have been widely used, their restricted biocompatibility for eukaryotic cells and attenuated antibacterial-effects due to compound release limit their areas of application and alternative strategies focus on modified surfaces topographies to impede bacterial adhesion. In this work, we used ns-UV laser treatment (wavelength 248 nm and a pulse duration of 20 ns) to generate laser-induced periodic surface structures (LIPSS) with different submicrometric periods ranging from ~210 to ~610 nm on commercial poly(ethylene terephthalate) (PET) foils. Following structurally and chemically analyses, PET samples were subjected to bacterial colonization studies with Escherichia coli TG1, a bacterial test strain with a strong biofilm formation capacity due to the formation of nanofiber-like cell-appendages (pili). Bacterial adhesion tests revealed that E. coli repellence decisively depends on the spatial periods of the LIPSS with the strongest reduction (~91%) in cell adhesion observed for LIPSS periods of 214 nm. Scanning electron microscopy and additional biofilm studies using a pili-deficient E. coli TG1 strain revealed the importance of extracellular appendages in the bacterial repellence observed here, thus, pointing out new antibiotics-free strategies for antibacterial surfaces by impeding nanofiber-mediated bacterial adhesion. T2 - E-MRS Spring Meeting 2022 CY - Online meeting DA - 30.05.2022 KW - Laser-induced periodic surface structures (LIPSS) KW - Bacterial adhesion tests KW - Bacteria repellent surfaces KW - Polymer foils KW - E. coli PY - 2022 AN - OPUS4-54930 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlegel, Moritz-Caspar T1 - Circular Economy - Materialeffizienznormen und -leitfäden N2 - Deutschland befindet sich inmitten eines umfassenden Transformationsprozesses hin zu einer klimaneutralen und nachhaltigen Wirtschaft und Gesellschaft. Sowohl das Erreichen der Klimaziele als auch die Anpassung an die Folgen des Klimawandels fordern ein rasches, bestimmtes und gleichzeitiges Handeln in vielen Sektoren und Lebensbereichen. Normen und Standards können einen wichtigen Beitrag zum Erreichen dieser Ziele leisten. So haben Normungsorganisationen weltweit mit der ISO London Declarationeinen Pakt zur Unterstützung des Klimas geschlossen. Das bestehende Normenwerk muss auf Klimawandel-Tauglichkeit überprüft und eine Überarbeitung angestoßen werden. Der Klimawandel als Querschnittsthema betrifft alle Wirtschaftszweige, und daher bieten DIN, DKE und VDI mit dieser durch Impulsvorträge eingeleiteten Diskussionsreihe eine Plattform zum Austausch über Normung als Werkzeug zum Thema Klima mit allen Akteuren. T2 - DIN/DKE/VDI-Frühstücksreihe: Klima und Normung CY - Berlin, Germany DA - 08.11.2022 KW - Circular Economy KW - Ökodesign KW - Materialeffizienz KW - Ressourceneffizienz KW - Energieeffizienz KW - Produktdesign PY - 2022 AN - OPUS4-56183 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stawski, Tomasz A1 - Van Driessche, A. T1 - Particle-mediated origins of mesocrystalline disorder in calcium sulfate single crystals N2 - Calcium sulfate minerals are abundant in natural and engineered environments and they exist in the form of three hydrates: gypsum (CaSO4·2H2O), bassanite (CaSO4·0.5H2O), and anhydrite (CaSO4). Due to their relevance in natural and industrial processes, the formation pathways of these calcium sulfate phases from aqueous solution have been the subject of intensive research1. The state-of-the-art of the calcium sulfate formation mechanisms builds upon and goes beyond what we have come to appreciate in the astounding intricacy of other mineral formation processes from ions in aqueous solutions. The original, and rather naive, 'textbook' image of these phenomena, stemming from the adaptation of classical nucleation and growth theories, has increased in complexity due to the discovery of a variety of precursor and intermediate species2. These include solute clusters (e.g. prenucleation clusters, PNCs), liquid(-like) phases, as well as amorphous and nanocrystalline solids etc.. In this context, a number of studies have already revealed that nucleation in the CaSO4-H2O system is non-classical, where the formation of the different crystalline phases involves several steps including a common amorphous precursor1, 3, 4. In this contribution we show that the formation of the amorphous phase involves the aggregation of small primary particles into larger disordered aggregates exhibiting a "brick-in-the-wall" structure5, 6. The actual crystallization occurs by the restructuring and coalescence of the particles ("bricks") into a given calcium sulfate phase depending on the physicochemical conditions of the solution. Importantly, the rearrangement process does not continue until a (nearly-)perfect homogeneous single crystal is obtained. Instead it comes to a stop, or at least significantly slows down. Such a process thus yields a final imperfect mesocrystal, composed of smaller domains rather than a continuous crystal structure, within which the domains are separated by an amorphous (i.e. less ordered) calcium sulfate phase. Hence, the non-classical crystallization process of CaSO4 yields a final imperfect mesocrystal with an overall morphology resembling that of a single crystal, yet composed of smaller nano-domains. Importantly, these observations reveal that organic-free calcium sulfate mesocrystals grown by a particle mediated-pathway preserve in the final crystal structure a “memory” or “imprint” of their non-classical nucleation process, something that has been overlooked until now. Furthermore, the nano-scale misalignment of the structural sub-units within these crystals can propagate through the length-scales, and be expressed macroscopically as misaligned zones/domains in large single crystals. Indeed, by considering large anhydrite crystals from the famous Naica Mine (“Cueva de los cristales”) we observed a suite of correlated self-similar void defects spanning multiple length-scales7. These flaws, in the macroscopic crystal, stem from “seeds of imperfection” originating from a particle-mediated nucleation pathway. Hence, building a crystal could be viewed as Nature stacking blocks in a game of Tetris, whilst slowly forgetting the games core concept and failing to fill rows completely. T2 - ECCG: European Conference on Crystal Growth 7 CY - Paris, France DA - 25.07.2022 KW - Anhydrite KW - SAXS KW - Single crystal KW - Mesocrystal PY - 2022 AN - OPUS4-56276 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Aktuelles aus der Arbeit des BAM-Fachbeirats N2 - Der Fachbeirat kommt bereits seit 13 Jahren in seiner jetzigen Form zusammen, um Zulassungsrichtlinien, weitere Dokumente und fachliche Fragestellungen zu beraten. Die Zeit bringt auch personelle Veränderungen mit sich, darüber wollen wir berichten. Derzeit wird die Zulassungsrichtlinie für Schutzschichten im Fachbeirat und in seiner Arbeitsgruppe Geotextilien und Kunststoff Dränelemente (AG Geotextilien) überarbeitet. Zudem wurde die Zulassungsrichtlinie für Kunststoffdichtungsbahnen auf den aktuellen Stand der Regelsetzung und Normung gebracht. Bestimmte Medien, die hier bei einigen Prüfungen verwendet werden, dürfen nicht mehr in der EU in Verkehr gebracht werden. Hier werden die Hintergründe und Zusammenhänge in Kürze aufgezeigt. Zuletzt wird die Diskussion in Bezug auf den Einsatz von Rezyklaten in den zugelassenen Produkten aufgeführt. T2 - Karlsruher Deponie- und Altlastenseminar 2022 CY - Karlsruhe, Germany DA - 19.10.2022 KW - Deponie KW - Abdichtungssystem KW - Schutzschichten PY - 2022 AN - OPUS4-56210 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Frenzel, Olivia A1 - Piechotta, Christian T1 - Identification of transformation products and metabolites of selected Bisphenols N2 - Bisphenol A (BPA) is widely used in many Polymers. Many outdoor applications are made from BPA-based materials which are exposed to a variety of environmental impacts, like temperature, solar radiation, rain, and others. This could lead to damaging and aging of the material which might cause leaching or migration of pollutants into the environment. To understand the fate and behavior different transformation products of selected Bisphenols will be generated and analyzed. T2 - Umwelt2022 CY - Emden, Germany DA - 05.09.2022 KW - Environment KW - Bisphenols KW - Transformation products KW - Metabolites KW - Wastewater PY - 2022 AN - OPUS4-56203 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreiber, Frank T1 - Biocides As Drivers For Antimicrobial Resistance Evolution In The Environment N2 - Antimicrobial resistance (AMR) is a global health problem with the environment being an important compartment for the evolution, selection and transmission of AMR. These processes are impacted by pollution with antibiotics. However, biocides used as disinfectants and material preservatives are major pollutants by far excceding the market for antibiotics in terms of mass. Our work shows that biocides have the potential to affect evolutionary processes towards AMR by increasing the rates of de-novo mutation and conjugation. These effects depend on the species and biocidal substance. Importantly, chlorhexidine and quaternary ammonium compounds (QACs) affect rates of mutation and conjugation at environmentally relevant concentrations in E. coli. Moreover, our results show a connection between the RpoS-mediated general stress and the RecA-linked SOS response with increased rates of mutation and conjugation, but not for all biocides. Furthermore, our work highlights the potential of biocides to contribute to selection and transmission of AMR. We show that the application of biocides, especially QAC disinfectants, leads to the rapid evolution of tolerance (i.e. increased survival) in adaptive laboratory evolution (ALE) experiments. The evolved tolerant strains have a selective advantage in the presence of environmentally-relevant concentrations of antibiotics, which could lead to the stabilization of biocide tolerance in environments where biocides and antibiotics co-occur (e.g. wastewater, animal stables). ALE experiments with biocide tolerant strains indicate a decreased evolvability of resistance to antibiotics. Taken together, our work shows the importance of assessing the contribution of biocides on evolution, selection and transmission of AMR in the environment. T2 - 6th Environmental Dimension of Antibiotic Resistance (EDAR6) CY - Gothenburg, Sweden DA - 22.09.2022 KW - Antimicrobial resistance KW - Antimicrobial coating KW - Biofilms KW - Biocides KW - Risk assessment PY - 2022 AN - OPUS4-56262 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreiber, Frank T1 - Biocide Resistance - Road to Risk Assessment N2 - This presentation details the current status of biocide resistance risk assessment and provides a roadmap for future activities. T2 - OECD, 6th Meeting of the Working Party on Biocides CY - Paris, France DA - 28.09.2022 KW - Antimicrobial resistance KW - Antimicrobial coating KW - Standardization KW - Biocides KW - Risk assessment PY - 2022 AN - OPUS4-56263 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin A1 - Valet, Svenja A1 - Kotula, Stefan A1 - Burkert, Andreas T1 - Vorstellung des WIPANOVerbundforschungsvorhabens GELELEK: Forschungsziele und Ergebnisse N2 - Der Vortrag stellt das WIPANO-Forschungsvorhaben GELELEK vor und fasst die wichtigsten erzielten Ergebnisse zusammen. T2 - Sitzung des GfKORR Arbeitskreises „Korrosion und Korrosionsschutz von Eisen und Stahl“ CY - Online meeting DA - 08.12.2022 KW - Deckschichtbildung KW - Gelartige Elektrolyte KW - Korrosionsuntersuchungen KW - Normung KW - Ringversuch KW - WIPANO KW - Zink KW - Korrosion PY - 2022 AN - OPUS4-56502 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rockland, Ulrike T1 - EPREL – eine Herausforderung? N2 - Der Vortrag fasst den derzeitigen Entwicklungsstand der europäischen Produktdatenbank EPREL für energieverbrauchsrelevante Produkte mit Fokus auf Leuchtmitteln zusammen. T2 - Mitgliederversammlung des Arbeitgeberverbands Leuchten- und Zubehör-Industrie (VLZ) CY - Online meeting DA - 15.09.2021 KW - EPREL-Produktdatenbank KW - EU-Energielabel KW - Energieverbrauchskennzeichnung PY - 2021 AN - OPUS4-54803 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Harrer, Andrea T1 - Energieverbrauchskennzeichnung für Lichtquellen die neuen Regeln und ihre Auswirkungen auf die Leuchtenindustrie N2 - Seit dem 1. September 2021 gelten zwei neue europäische Verordnungen für Lichtquellen, welche deren umweltgerechte Gestaltung und ihre Energieverbrauchkennzeichnung regeln. In diesem Vortrag werden die neuen Anforderungen und ihre Auswirkungen auf die Leuchtenindustrie erläutert. T2 - Mitgliederversammlung des Arbeitgeberverbands Leuchten- und Zubehör-Industrie (VLZ) e.V. CY - Online meeting DA - 15.09.2021 KW - Ökodesign KW - Energieverbrauchskennzeichnung KW - Beleuchtung PY - 2021 AN - OPUS4-54723 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rockland, Ulrike T1 - Die Europäische Datenbank EPREL – eine Herausforderung? N2 - Der Vortrag informiert über die neuen Anforderungen der EU-Kommission an Lieferanten, die energieverbrauchsrelevante Produkte mit EU-Energielabel in die Datenbank EPREL hochladen müssen. T2 - 8. Praxisworkshop Marktüberwachung EVPG/EnVKG 2022 CY - Online meeting DA - 11.05.2022 KW - EPREL-Produktdatenbank KW - EU-Energielabel KW - Energieverbrauchskennzeichnung PY - 2022 AN - OPUS4-54804 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Olbrich, Adelina-Elisa A1 - An Stepec, Biwen Annie A1 - Koerdt, Andrea A1 - Meermann, Björn T1 - Material vs. Environment: Uncovering microbiological influenced corrosion processes on steel with single cell-ICP-ToF-MS N2 - Microbiologically influenced corrosion (MIC) is a highly unpredictable process dictated by the environment, microorganisms, and the respective electron source. Interaction pathways between cells and the metal surface remain unclear. The development of this novel single cell-inductively coupled plasma-time of flight-mass spectrometry analytical method and a MIC-specific staining procedure facilitate the investigation of steel-MIC interactions. With this it is possible to analyze the multi-elemental fingerprint of individual cells. The detection method revealed elemental selectivity for the corrosive methanogenic archaeal strain Methanobacterium-affiliated IM1. The interface between material and environmental analysis thus receives special attention, e.g., when considering MIC on solid steel. Hence, the possible uptake of individual elements from different steel samples is investigated. Results showed the cells responded at a single-cell level to the different types of supplemented elements and displayed the abilities to interact with chromium, vanadium, titanium, cobalt, and molybdenum from solid metal surfaces. The information obtained will be used in the future to elucidate underlying mechanisms and develop possible material protection concepts, thus combining modern methods of analytical sciences with materials research. T2 - ToFcon 2022 CY - Online meeting DA - 17.11.2022 KW - Single cell KW - Microbiological influenced corrosion MIC KW - Sc-ICP-ToF-MS KW - Method development KW - Ir DNA staining approach KW - Carbon steel corrosion PY - 2022 AN - OPUS4-56355 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - von Werder, Julia A1 - Stohl, Leonie T1 - Biorezeptive Betonfassaden: Algenbiofilme als Gestaltungselement und zur Verbesserung des Stadtklimas N2 - Der Vortrag fasst den aktuellen Stand der Forschung an der BAM zum Thema "Biorezeptive Betonfassaden" zusammen. Während im Projekt Funktionsbeton der Einfluss der Textur von ultrahochfestem Beton auf die Biorezeptivität im Vordergrund steht, wird im Projekt Algenbiofilmfassade untersucht, inwieweit ein Biofilm künstlich auf Betonsubstraten etabliert werden kann. T2 - BUGG-Tag der Forschung und Lehre Gebäudegrün 2022 CY - Stuttgart, Germany DA - 10.05.2022 KW - Biofilm KW - Biorezeptivität KW - Beton KW - UHPC KW - Fassade PY - 2022 AN - OPUS4-56388 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Resch-Genger, Ute A1 - Tavernaro, Isabella A1 - Nirmalananthan-Budau, Nithiya T1 - Functional molecular chromophores and nanomaterials reporters, optical probes, and sensors N2 - •Overview of expertise of division Biophotonics •Functional molecular and nanoscale luminescent reporters, probes, and sensors including design principles available from division Biophotonics •Examples for pH and O2 responsive molecular probes and particle sensors •Surface group quantification Analytical methods and cleavable probes •Concepts & standards for the validation and traceability of optical measurements T2 - FU-Seminar CY - Berlin, Germany DA - 09.12.2022 KW - Particle sensors KW - Surface group quantification KW - Nanoscale luminescent reporters KW - Cleavable probes PY - 2022 AN - OPUS4-56526 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Meermann, Björn T1 - Single cell ICP-ToF-MS as a powerful tool in environmental and material research N2 - Materials are key for our modern communities. In particular metals play important roles in all areas of our daily life - from building materials to high tech products. Due to the increasing consumption of metals and corresponding waste production, an elevated release into the environment takes place. Furthermore, metals in direct contact with the environment undergo corrosion leading to a release into the (aquatic) environment. Thus, lifespan of products/buildings are substantially reduced – hence unnecessary economic costs arise. Thus, research in this regard is needed within the force field of metal/material - environment. Evaluating the environmental impact of materials as well as developing “safe” materials, new analytical methods are highly needed. One promising powerful tool is single cell-ICP-ToF-MS for multi-elemental analysis on a single cell/organism level. Within this presentation the concept, strength as well as challenge of single cell-ICP-MS are briefly introduced. Two application examples are presented: (i) assessing the environmental impact of metals and (ii) the impact of the environment on metal-based materials and the derivation of potential environmental-friendly material protection strategies. These applications highlight the strength of new analytical approaches to explore the durability and safety of newly developed materials. Thus, analytical chemistry is one corner stone to transformation of modern society into circular economy (CEco). (i) Diatoms are located at the bottom of the food chain. Thus, toxicological relevant metals taken up by diatoms possibly accumulate within the food web causing harmful effects. Diatoms are common test system in ecotoxicology. To investigate potential metal uptake and effects, we developed an on-line single cell-ICP-ToF-MS approach for multi-elemental diatom analysis. Our approach is a new potential tool in ecotoxicological testing for metal-based materials. (ii) Next to classical corrosion processes, microorganisms are responsible for so called microbially influenced corrosion (MIC). MIC is a highly unpredictable process relying on interaction pathways between cells and the metal surface. Sheding light on MIC processes and derivate potential protection strategies, we applied single cell-ICP-ToF-MS for MIC research on a single bacteria/archaea level. It turned out that microorganism are taking up particular metals from alloys - thus, single bacteria-ICP-ToF-MS will enable development of corrosion protection strategies. T2 - SCIX 2022 CY - Cincinnati, OH, USA DA - 02.10.2022 KW - Single cell-ICP-ToF-MS KW - Algae KW - MIC PY - 2022 AN - OPUS4-56542 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Selina A1 - Schreiber, Frank T1 - Effect of biocides on the evolution and spread of resistance N2 - Biocides used as material preservatives are in contact with various environments during direct application or passive leaching from protected materials. Antimicrobial resistance (AMR) is a global health problem and the environment is an important compartment for the evolution and transmission of AMR. Soil is an environment with a large reservoir of natural microbial communities and antimicrobial resistance (AMR) genes. Those natural microbial communities are frequently exposed to biocides used as material preservatives. Previous studies have shown that antibiotics, metals and pesticides affect the underlying processes of resistance evolution and spread; namely de novo mutagenesis and horizontal gene transfer by conjugation and transformation in microbial communities. However, it is unknown if active substances used in material preservatives are involved in these processes. We show that biocides used as material preservatives affect rates of mutation and conjugation in microorganism in a species- and substance-dependent manner, while rates of transformation are not directly affected. Our data highlights the importance of assessing the contribution of material preservatives on AMR evolution and spread in the environment. T2 - Microbiome Network Meeting CY - Berlin, Germany DA - 20.07.2022 KW - Biocides KW - Antimicrobial resistance KW - Horizontal gene transfer KW - Mutation rate PY - 2022 AN - OPUS4-56426 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gerrits, Ruben T1 - Fungal biofilms are supported by EPS and protective pigments in their substrate attachment and desiccation tolerance N2 - Rock-inhabiting fungi are known to colonise air-exposed substrates like minerals, photovoltaic panels building facades and monuments, withstanding the various stresses these extreme habitats are known for. Here we show how both colonisation and stress resistance are linked to the properties of the fungal cell surface. By deleting genes involved in the synthesis of melanin and carotenoid pigments of the model rock-inhabiting fungus Knufia petricola via CRISPR-Cas and comparing the behaviour of the gene-deletion mutants with the wild type (WT), we studied the role of these genes in mineral colonisation and stress sensitivity. The extracellular polymeric substances (EPS) of biofilms of the WT and mutants were extracted, quantified and chemically characterised. We observed that the absence of melanin affected the quantity and composition of the produced EPS: melanin-deficient mutants synthesised more EPS containing fewer pullulan-related glycosidic linkages. Moreover, in mineral dissolution experiments, these mutants showed a lower ability to colonise the mineral olivine. We hypothesise that not melanin, but the pullulan-related linkages enabled the melanin-producing strains to attach more strongly to the mineral. Moreover, ICP-OES analysis of the aqueous mineral-derived solutes showed that biofilms of the K. petricola mutants which could attach were able to dissolve the olivine faster than those that could not. The same mutants were also characterised by their sensitivity to desiccation stress: only the mutant deficient in both melanin and carotenoid synthesis was more sensitive to desiccation compared to the WT, indicating that a combination of both pigments is critical to withstand desiccation. Overall, these results show the critical role of the cell surface in the specific capacities of rock-inhabiting fungi. T2 - Biofilms 10 CY - Leipzig, Germany DA - 09.05.2022 KW - Bio-weathering KW - Desiccation KW - Fungal biofilms PY - 2022 AN - OPUS4-56675 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlegel, Moritz-Caspar T1 - Ökodesign und Circular Economy - Normungsroadmap C-Eco, Normung zu ErP und Ressortforschung N2 - (i) Überblick zum aktuellen Stand der Normung und aktuellen Normungsvorhaben im Bereich Ökodesign. (ii) Vorstellung des Forschungsprojektes (Steigerung der produktbezogenen Energie- und Ressourceneffizienz) vor allem in Hinblick auf Vorhaben die sich auf die Langlebigkeit, Reparierbarkeit und Recyclingfähigkeit. T2 - Expertenforum „Global Environmental Compliance“ - Fraunhofer IPA CY - Stuttgart, Germany DA - 24.03.2022 KW - Circular Economy KW - Ecodesign KW - Produkteffizienz KW - Materialeffizienz KW - Ressourceneffizienz KW - Ressortforschung KW - WUP PY - 2022 AN - OPUS4-54532 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin A1 - Haacke, Nasrin T1 - Forschungsprojekt RUNOFF: "Neubewertung der Dauerhaftigkeit von Dach- und Fassadenmaterialien und des Eintrags von Schwermetall-Ionen in die Umwelt hervorgerufen durch Runoff„ N2 - Bei Betrachtungen zur Lebensdauer von Metallbauteilen im Bauwesen müssen Korrosions- und Runoff-Vorgänge an der Atmosphäre als verschiedene Reaktionen unterschieden werden. Korrosion ist der Prozess, der von elektrochemischen Reaktionen an der Grenzfläche Metall/Patina kontrolliert wird. Runoff dagegen wird durch chemische Reaktionen an der Grenzfläche Patina/Atmosphäre begünstigt. Mit zunehmender Bewitterungszeit nimmt die Korrosionsgeschwindigkeit stetig ab, während postuliert wird, dass die Geschwindigkeit des Runoffs über die gesamte Zeit konstant bleibt. Dieses Verhalten des Runoffs muss aber zunehmend bezweifelt werden. Die Gesamtmenge an abgezehrtem Metall beinhaltet zwei Bestandteile. Ein Teil wird in die Schicht aus Korrosionsprodukten eingebaut, der andere wird aufgrund von Niederschlägen aus der Patina gelöst. Aus diesem Grund ist die Menge an Zink-Runoff stark abhängig von den Eigenschaften der Korrosionsprodukt- bzw. Patinaschicht und nicht anhand der Zusammensetzung des Metalls abschätzbar. Vorhandene Modelle können die Menge an Runoff, und damit verbunden die Abzehrung einer Schicht aus Zink und Kupfer, sowie den resultierenden Eintrag von Schwermetallionen in die Umwelt nicht mehr darstellen und erklären. Um den Korrosionsschutz an Bauwerken zum einen dauerhaft unter Beachtung von Kostenaspekten und Ressourcenschonung und zum anderen unter ökologischen Gesichtspunkten auslegen zu können, müssen deshalb neue wissenschaftliche Grundlagen erarbeitet und die Mechanismen beschrieben werden. Das BAM-Forschungsvorhaben RUNOFF widmet sich den Fragestellungen. Der Vortrag gibt einen kurzen Überblick zum Forschungsvorhaben. T2 - 19. Projektetage der Bauforschung CY - Online meeting DA - 22.03.2022 KW - Runoff KW - Zink KW - Korrosion KW - Kupfer PY - 2022 AN - OPUS4-54580 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, Julia A1 - Breitenbach, Romy A1 - Erdmann, Eileen A1 - Gerrits, Ruben A1 - Heeger, Felix A1 - Nitsche, Sarah A1 - Tonon, Chiara A1 - Voigt, Oliver A1 - Gorbushina, Anna T1 - Knufia petricola – a model for exploring the biology of black rock-inhabiting fungi N2 - Black fungi also called black yeasts, rock-inhabiting fungi or microcolonial fungi are a group of Ascomycetes [Eurotiomycetes, Arthoniomycetes and Dothideomycetes] that exhibit high stress tolerance, yeast‑like or meristematic growth, and constitutive 1,8-dihydroxynaphthalene (DHN) melanin formation. They dominate a range of hostile natural and man‑made environments – from desert rocks and salterns to dishwashers, roofs, and solar panels. Due to their slow growth and the lack of sexual cycles and genetic tools, the underlying mechanisms of black fungi’s phenotypic traits have remained largely unexplored. We consider the rock inhabitant K. petricola [Eurotiomycetes, Chaetothyriales] a suitable model for studying the phenotypic characteristics of black fungi. With K. petricola the regulation of pigment synthesis, general stress responses and the unusual modes of cell division can be dissected by advanced reverse and forward genetics approaches. The genome of K. petricola strain A95 was sequenced using a combination of short high quality Illumina reads and long PacBio reads. The final assembly consists of twelve contigs: five complete chromosomes and six contigs with one telomer each. Gene annotation supported by transcriptomics and proteomics data was manually curated. Recently, we developed a set of genetic tools to manipulate the genome for analyzing gene functions and studying the cell biology. This set includes CRISPR/Cas9-based genome editing and live-cell imaging using genetically encoded fluorescent proteins, as well as protocols for -omics approaches and for simulation of mineral weathering in the laboratory. Mutants defective in DHN melanogenesis, carotenogenesis or both processes are currently studied to elucidate the role of these protective pigments in tolerance of natural and man-made stresses, weathering of olivine, penetration of marble, and adhesion to surfaces. Further, the established protocols and knowledge gained from K. petricola form a starting point for making other extremotolerant black fungi accessible to genetic manipulation. T2 - 31st Fungal Genetics Conference CY - USA, CA, Pacific Grove DA - 15.03.2022 KW - Black fungi KW - Melanin KW - Genome editing PY - 2022 AN - OPUS4-54585 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erning, Johann Wilhelm T1 - Materials in contact with drinking water and regulatory issues N2 - The state of play in regard to regulations of materials in contact with drinking water in europe is discussed T2 - Kormat 2022 CY - Online meeting DA - 26.04.2022 KW - Korrosion KW - Trinkwasser KW - Hygiene KW - Risikobewertung PY - 2022 AN - OPUS4-54710 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Stohl, Leonie A1 - von Werder, Julia T1 - Bioreceptivity of Concrete Facades N2 - In recent years, the demand for new and sustainable products has been constantly rising. Especially cementitious materials are known for their high carbon footprint and novel approaches will be needed to counterbalance that. The BAM departments 7.1 (building materials) and 4.0 (Material and the environment) try to improve the sustainability of concrete panels by establishing a biofilm on the weather protection layer. Using an ultra-high-performance-concrete allows the production of very thin facade tiles with a small carbon footprint. Furthermore, the durability of these tiles is expected to surpass the one of “normal” concrete facades and offer the possibility of modular renewing of defective tiles instead of a wall, or even remodeling a whole building. The controlled application of biofilms on facades aims to improve biodiversity, microclimate, and air quality in cities. Furthermore, the greening of typically gray surfaces could improve the mental health of the residents. The project focuses on testing a multiplicity of concrete samples, varying e.g., in roughness or pH. The bioreceptivity is analyzed via laboratory tests, as well as in perennial outdoor experiments. T2 - Biology versus building materials: from biocides to bio-receptivity CY - Online meeting DA - 08.02.2022 KW - Bioreceptivity KW - Algea KW - Concrete KW - Biofilm PY - 2022 AN - OPUS4-54470 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koerdt, Andrea T1 - Mikrobiell beeinflusste Korrosion (MIC) – Wenn MIC dann BAM N2 - In dieser Präsentation wurden dem Beirat Umwelt die High-Lights und der weitere Ausblick des Foresight Process MIC vorgestellt. Im Fokus stehen hierbei insbesondere die neu angelaufenen Projekte: COST Action Euro-MIC MIC im Endlager Hydrogen: MIC & Wasserstoffversprödung Biorezeptivität von Betonoberflächen Mitigation schwarze Pilze WIPANO ResTest T2 - Beirat Umwelt CY - Online meeting DA - 11.03.2022 KW - MIC KW - Hi-Tension KW - Projekte PY - 2022 AN - OPUS4-54463 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schoknecht, Ute T1 - Leaching und Transformation von Bioziden aus Fassadenfarben N2 - Anhand von Beobachtungen aus Labor- und Freilandversuchen wird dargestellt, wie Wasserkontakt und Strahlung die Auslaugung und Transformation der Wirkstoffe Diuron und Terbutryn beeinflussen. Auf Optionen zur modellhaften Darstellung dieser Prozesse wird kurz eingegangen. T2 - OMiBiB - Optimierung und Minimierung des Biozideinsatzes in Baustoffen CY - Online meeting DA - 09.02.2022 KW - Leaching KW - Transformation KW - Biozide KW - Fassadenfarben PY - 2022 AN - OPUS4-54318 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koerdt, Andrea T1 - Cost action EURO MIC (CA20130) N2 - Vorstellung des vor kurzen angelaufenen EU-Projekts: COST ACTION EURO MIC ( CA20130). Die BAM hat hierbei die Rolle des Chairs sowie Grant-Holding Institute. COST fördert internationale Netzwerk Aktivitäten. Durch COST Action können neue Kooperationen (Industrie, Akademie oder Politk) entstehen. T2 - Dechema CY - Online meeting DA - 10.11.2021 KW - Netzwerk KW - COST KW - Mikrobiell beeinflusste Korrosion KW - MIC PY - 2021 AN - OPUS4-54023 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin A1 - Valet, Svenja A1 - Kotula, Stefan A1 - Burkert, Andreas T1 - Vorstellung des WIPANOVerbundforschungsvorhabens GELELEK: Forschungsziele und Ergebnisse N2 - Der Vortrag stellt das WIPANOForschungsvorhaben GELELEK vor und fasst die wichtigsten erzielten Ergebnisse zusammen. T2 - 13. Sitzung des GfKORR Arbeitskreises „Korrosionsuntersuchung und -überwachung“ CY - Online meeting DA - 08.12.2021 KW - Deckschichtbildung KW - Gelartige Elektrolyte KW - Korrosionsuntersuchungen KW - Normung KW - Ringversuch KW - Zink KW - WIPANO PY - 2021 AN - OPUS4-53946 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erning, Johann Wilhelm T1 - Bauteile aus additiv gefertigtem Werkstoff 1.4404 in der Trinkwasserinstallation N2 - Elektrochemische Messungen zur hygienischen Bewertung additiv gefertigter Bauteile werden diskutiert. Die Bewertung und Details des Werkstoffs werden beschrieben, Anwendungsbeispiele gezeigt. T2 - GfKORR AK Eisen und Stahl CY - Online meeting DA - 14.12.2021 KW - Korrosion KW - Trinkwasser KW - Hygienische Bewertung KW - Additive Fertigung PY - 2021 AN - OPUS4-54024 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koerdt, Andrea A1 - Babutzka, Martin A1 - Zekhnini, Khalid T1 - Mikrobielle Zusammensetzung im Wassertank N2 - Der Fachbereich 7.6 untersucht seit einiger Zeit an Auslagerungsständen auf dem Testgelände in Horstwalde Korrosion im maritimen Bereich. Im Moment läuft das System mit künstlichem Meerwasser und simuliert die Bewitterung von Metallproben unter angenäherten klimatischen Bedingungen ähnlich zum natürlichem Habitat. Im Laufe der Zeit konnte nicht intendierter mikrobieller bewuchs beobachtet werden. Es stellte sich die Frage, welche Mikroorganismen vorlagen und ob diese einen Einfluss auf die Korrosionsuntersuchungen haben könnte. Aus diesem Grund wurden 16S-rRNA Untersuchungen durchgeführt welche alle drei Domänen des Lebens widerspiegeln Bakterien, Archaea und Eukaryoten. Es konnte gezeigt werden, dass über 95% der vorliegenden Biomasse Grünalgen waren, die durch Licht Eintrag in den Container Photosynthese betrieben und dadurch an Biomasse zunahmen. Des weiteren konnten Bakterien detektiert werden, welche in der Regel halophilen und aeroben Habitaten zu finden sind. Allerdings wurden auch Sulfat reduzierende Bakterien (MIC) detektiert, wenn auch in einem geringen prozentualen Anteil. Es muss allerdings Berücksichtigt werden, dass die mikrobielle Zusammensetzung sich im Laufe der Zeit weiter ändern kann. Als Ursprung der Biomasse wird, das künstliche Sediment vermutet. Außerdem wäre es für zukünftige Experiment denkbar, das System mit echtem Sediment aus dem marinen Habitat anzuimpfen. T2 - Dechema CY - Online meeting DA - 10.11.2021 KW - Mikroorganismen KW - Mikrobielle Gemeinschaft KW - Korrosion KW - Simulation PY - 2021 AN - OPUS4-54035 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Deland, Eric A1 - An, Biwen Annie A1 - Sobol, Oded A1 - Yao, J. A1 - Skovhus, T. L. A1 - Koerdt, Andrea T1 - Environmental conditions affect the corrosion product composition of Methanogen induced microbiologically influenced corrosion (Mi-MIC) N2 - Corrosion is a very expensive and serious problem in the different industry sectors, eg. Petroleum-, On- and off-shore, infrastructure. It is estimated that 20% of all corrosion damage is caused by microorganisms or microbiologically influenced corrosion (MIC). Several microorganisms are known to cause corrosion, including sulfate-reducing bacteria, nitrate-reducing bacteria, methanogens etc. For several years, methanogens were regarded as a mild corroder (~0.065 mm/yr), largely due to a lack of detailed investigation on the corrosion mechanism under real-environment simulated conditions. Resulting in the common belief that siderite, a non-conductive compound, is the sole corrosion product (CP) of methanogen-induced MIC (Mi-MIC). To simulate natural environmental conditions, we developed and introduced the multiport flow column system (MFC), a multi-sectional corrosion flow-cell. Using the MFC, we obtained ten times higher corrosion rates than previously reported. With a combination of several analytical techniques, such as ToF-SIMS, SEM-EDS and FIB-SEM, we found strong indication that siderite is not the sole corrosion product of Mi-MIC. The corrosion layers contained phosphorus, oxygen, magnesium, calcium and iron. The differences in the CP between static and dynamic environments demonstrated the impact of testing procedures on the corrosive potential of methanogens. To further verify and deepen our understanding of Mi-MIC, we are currently studying the influence of additional environmental parameters (e.g. pH, salinity, flow rate) on Mi-MIC. Overall, results of this study will expand the current understanding of MIC from both analytical and mechanistic points of view, thus aiding the development of different mitigation strategies for various industry sectors. T2 - ISMOS-8 CY - Online meeting DA - 08.06.2021 KW - Methanogen-induced microbiologically influenced corrosion KW - Carbon steel KW - ToF-SIMS KW - Modelling studies PY - 2021 AN - OPUS4-54041 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Deland, Eric A1 - Kleinbub, Sherin A1 - An, Biwen Annie A1 - Sobol, Oded A1 - Yao, J. A1 - Skovhus, T. L. A1 - Koerdt, Andrea T1 - Is Methanogen-induced microbiologically influenced corrosion (Mi-MIC) underestimated? N2 - The role of methanogens in microbiologically influenced corrosion (Mi-MIC) is often neglected, due to 1) low reported corrosion rates and 2) the suspected corrosion product siderite, which is electrically non-conductive. Typically, MIC corrosion studies are carried out using batch cultures, which did not represent the dynamic conditions, i.e. pipeline and provide insufficient information on the overall corrosion potential. We established a unique approach, a multiport flow column (MFC), to simulate pipeline conditions and obtained 10-times higher corrosion rates than previously published. Our result showed that testing procedures have a large impact on the corrosive potential of methanogens. We found strong indications with a combination of ToF-SIMS, SEM-EDS and FIB-SEM analyses that siderite is not the sole corrosion product. The corrosion layers contain phosphorus, oxygen, magnesium, calcium and iron. To verify and deepen our understanding of Mi-MIC, we are currently studying the influence of other environmental parameters (e.g. pH) on Mi-MIC. T2 - VAAM 2021 CY - Online meeting DA - 18.03.2021 KW - Methanogen-induced microbiologically influenced corrosion KW - Carbon steel KW - MIC Island PY - 2021 AN - OPUS4-54042 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Deland, Eric A1 - An, Biwen Annie A1 - Sobol, Oded A1 - Yao, J. A1 - Skovhus, T. L. A1 - Koerdt, Andrea T1 - Environmental conditions impact the corrosion layer composition of Methanogen induced microbiologically influenced corrosion (Mi-MIC) N2 - Microbiologically influenced corrosion (MIC) is a now well-known challenge and affects industry, society and infrastructure. For a long time, the impact of methanogen-induced MIC (Mi-MIC) was underestimated. This was mainly due to the rather low published corrosion rates and the presumed corrosion product siderite, which is not electrically conductive. In our laboratory, we were able to show that this trivialization or underestimation of Mi-MIC was due to the nature of the testing. The static systems used so far do not provide environmentally relevant information about the corrosion rate and the corrosion product, especially for methanogens To further illustrate the importance of the environment on the MIC process, we established a multiport flow column (MFC), to simulate the natural environment. With this method, and in contrast to published results using the static conditions, we obtained ten times higher corrosion rates. We analyzed the corrosion products with a combination of techniques, like ToF-SIMS, SEM-EDS and FIB-SEM, and found strong evidence that siderite is not the sole corrosion product of Mi-MIC. The corrosion layers contain phosphorus, oxygen, magnesium, calcium and iron and lacked on carbon-related species. It is hypothesized that methanogens may have influenced the nucleation process of siderite, converting bicarbonate into carbon dioxide for methanogenesis. This results in increased localized corrosion and reduced siderite formation. To verify and deepen our understanding of Mi-MIC, we are currently studying the influence of additional environmental parameters (e.g. pH, salinity, flow rate etc.) on Mi-MIC and the subsequent impacts on corrosion rates and the corrosion products. Overall, results of this study will expand the current understanding of MIC from both analytical and mechanistic points of view, thus aiding the development of different mitigation strategies for various industry sectors. T2 - Eurocorr 2021 CY - Online meeting DA - 20.09.2021 KW - Methanogen-induced microbiologically influenced corrosion KW - Carbon steel KW - SEM-EDS KW - Modelling studies PY - 2021 AN - OPUS4-54043 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schröder, Nina A1 - Schaupp, Thomas A1 - Schröpfer, Dirk A1 - Kannengießer, Thomas T1 - Einfluss von Konstruktion und Wasserstoff auf die Kaltrissbildung beim Schweißen hochfester Feinkornbaustähle N2 - Der konstruktive Leichtbau erfordert den zunehmenden Einsatz hochfester Feinkornbaustähle mit Streckgrenzen bis zu 1300 MPa. Um darüber hinaus Schweißzeit, Schweißnahtvolumina und Schweißkosten zu minimieren, kam es zur Entwicklung moderner Lichtbogenprozesse mit erhöhter Abschmelzleistung, wie bspw. dem modifizierten Sprühlichtbogen. Das Schweißen mit modifiziertem Sprühlichtbogen bietet die Möglichkeit, schmalere Nahtfugen bzw. kleinere Nahtöffnungswinkel zu schweißen. Mit zunehmender Festigkeit der Baustähle steigen allerdings die Anforderungen an die schweißtechnische Verarbeitung. Hochfeste Feinkornbaustähle weisen ein erhöhtes Risiko gegenüber der wasserstoffunterstützten Kaltrissbildung auf. Diese Werkstofftrennungen entstehen unter gemeinsamer Wechselwirkung von lokalem risskritischem Gefüge, lokal erhöhter Wasserstoffkonzentration und lokal erhöhter Beanspruchung bzw. Dehnung. Untersuchungen haben gezeigt, dass der Einsatz des modifizierten Sprühlichtbogens in Verbindung mit schmalen Nahtfugen zu erhöhten Wasserstoffkonzentrationen im Schweißgut führt. Die vorliegende Arbeit gibt einen Aufschluss hinsichtlich der Kaltrissempfindlichkeit des vergüteten, hochfesten Feinkornbaustahls S960QL anhand der durchgeführten Kaltrissprüfung mittels selbstbeanspruchenden TEKKEN-Tests. Dazu wurden die Nahtöffnungswinkel der Prüfnähte zwischen 30° (Einsatz des modifizierten Sprühlichtbogens) und 60° (Einsatz des konventionellen Übergangslichtbogens) variiert. Ferner wurde die Wirksamkeit einer Nachwärmprozedur aus der Schweißwärme heraus zur Vermeidung der wasserstoffunterstützte Kaltrissbildung untersucht. Die Ergebnisse weisen in allen Proben (ohne Nachwärmung) Kerbrisse auf, welche als Kaltrisse identifiziert werden konnten. Durch eine Nachwärmung unmittelbar nach dem Schweißen können diese gänzlich vermieden werden. Das Schweißgut mit modifizierten Sprühlichtbogen weist die höchsten mittleren Wasserstoffkonzentrationen auf. Ferner zeigt das Schweißgut unter reduziertem Nahtöffnungswinkel eine vermehrte Mikrorissbildung auf. T2 - DVS-Bezirksverband Rostock CY - Rostock, Germany DA - 14.10.2021 KW - TEKKEN-Test KW - Hochfester Feinkornbaustahl S960QL KW - Wasserstoffunterstützte Kaltrissbildung KW - Diffusibler Wasserstoff KW - Nachwärmung (DHT) KW - Schweißeigenspannungen KW - MAG-Schweißen PY - 2021 AN - OPUS4-53744 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreiber, Frank T1 - Selection of resistance by antimicrobials used in coatings N2 - Antimicrobial surfaces have broad use in multiple settings including touch surfaces in hospitals, implanted devices, or consumer products. Their aim is to support existing hygiene procedures, and to help combat the increasing threat of antimicrobial resistance. However, concerns have been raised over the potential selection pressure exerted by such surfaces, which might drive the evolution and spread of antimicrobial resistance. In my presentation, I will highlight the risks and knowledge gaps associated with resistance on antimicrobial surfaces by different processes including evolution by de novo mutations and horizontal gene transfer, and species sorting of inherently resistant bacteria dispersed onto antimicrobial surfaces. The latter process has the potential to select for antibiotic resistance via cross-resistance between traits that confer resistance to both the antimicrobial surface coating and antibiotics. Conditions in which antibiotics and antimicrobial coatings are present simultaneously (e.g. implants) will lead to more complex interactions that can either result in the selection for or against antibiotic resistance. We mapped these interactions between several antimicrobials and antibiotics on growth and selection of Pseudomonas aeruginosa. We find prevalent physiological (i.e. synergy and antagonism) and evolutionary (i.e. cross-resistance and collateral sensitivity) combination effects. Understanding these interactions opens the door to tailor therapeutic interventions to select against resistance. In additions, we need new methods and translational studies that investigate resistance development to antimicrobial surfaces under realistic conditions. Therefore, I will present recent developments in our lab on the development of such a method based on existing efficacy standards. T2 - 2021 Fall Meeting of the European Materials Research Society (E-MRS) CY - Online meeting DA - 20.09.2021 KW - Antimicrobial resistance KW - Antimicrobial coating KW - Biofilms KW - Biocides PY - 2021 AN - OPUS4-53645 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute T1 - Wie naturnah simulieren die Elutionsverfahren? N2 - Die Untersuchung altlastverdächtiger Flächen umfasst viele einzelne Schritte von der Probenahme über die Probenvorbehandlung bis hin zur eigentlichen Analyse, die zur Ergebnisunsicherheit beitragen. Beim Vergleich der Ergebnisse mit Bewertungsmaßstäben, um Entscheidungen zur Bewertung von Altlasten zu treffen, sind diese Faktoren zu berücksichtigen. Die Rolle von verschiedenen Unsicherheitskomponenten wird mit Blick auf Elutionsverfahren diskutiert. T2 - Messen, schätzen und bewerten – Theorie und Praxis der Altlastenbewertung: Online-Altlastenseminar des LLUR CY - Online meeting DA - 27.09.2021 KW - Altlasten KW - Schadstofftransfer KW - Elutionsverfahren KW - BBodSchV KW - Ergebnisunsicherheit PY - 2021 AN - OPUS4-53623 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Aktuelle Diskussion aus dem Fachbeirat der BAM N2 - Das Jahr 2020 war vor allen Dingen von der Pandemie geprägt, die alle Bereiche des Lebens und Arbeitens beeinflusst hat und immer noch beeinflusst. Dies hat sich auch auf verschiedene Maßnahmen im Zusammenhang mit zugelassenen Produkten ausgewirkt. In diesem Zusammenhang sollen die Punkte kurz aufgeführt werden. Des Weiteren soll aufgezeigt werden, wie bei der Bearbeitung der Richtlinien, der Zulassungstätigkeit und Beurteilung der Produkte an der BAM und im Fachbeirat vorgegangen wird. Darüber hinaus soll noch einmal kurz auf die Entlassung aus der Nachsorgephase eingegangen werden. Am Ende sollen verschiedene aktuelle Fragestellungen des Fachbeirat aufgezeigt werden. T2 - 17. Leipziger Deponiefachtagung CY - Online meeting DA - 02.03.2021 KW - Deponie KW - Geokunststoffe KW - Kunststoffdichtungsbahn PY - 2021 AN - OPUS4-52213 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Neue Erkenntnisse zur Deckschichtbildung von Zink an der Atmosphäre N2 - Die Untersuchungen und Ausführungen im Vortrag belegen, dass verfügbare Modellvorstellungen zur Beschreibung der Deckschichtbildung und Korrosion von Zink unter aktuellen atmosphärischen Bedingungen in Europa nicht mehr gültig sind und neu bewertet werden müssen. So können beispielsweise bisher verfügbare Prognosemodelle den Korrosionsfortschritt nicht mehr ausreichend beschreiben, da durch die Verringerung des Schwefeldioxidgehaltes der Luft veränderte Mechanismen vorliegen. T2 - Sitzung des Forschungsbeirats des Gemeinschaftsausschuss Verzinken e.V. CY - Online Meeting DA - 07.10.2021 KW - Atmosphärische Korrosion KW - Deckschichtbildung KW - Gelartige Elektrolyte KW - Zink PY - 2021 AN - OPUS4-53478 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin A1 - Valet, Svenja A1 - Kotula, Stefan A1 - Burkert, Andreas T1 - Vorstellung des WIPANO-Vorhabens GELELEK N2 - Der Vortrag stellt das WIPANO-Forschungsvorhaben GELELEK vor und fasst die wichtigsten erzielten Ergebnisse zusammen. T2 - Sitzung des Forschungsbeirats des Gemeinschaftsausschuss Verzinken e.V. CY - Online meeting DA - 07.10.2021 KW - Deckschichtbildung KW - Gelartige Elektrolyte KW - Korrosionsuntersuchungen KW - Normung KW - Ringversuch KW - Zink PY - 2021 AN - OPUS4-53479 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koerdt, Andrea T1 - COST-Action - EURO-MIC (CA20130) European MIC Network - New paths for science, sustainability and standards N2 - Microbiologically Influenced Corrosion (MIC) is a phenomenon that is increasingly becoming a problem for the society. MIC describes the negative effects a material can experience due to the presence of microorganisms. In Europe, several research groups/ other industrial stakeholders are already dealing with MIC. Unfortunately, the discussions are fragmented and the exchange of information is limited. A true transdisciplinary approach is hardly ever experienced, although this would be logical for this material/biology related challenge. USA, Canada and Australia have strong networks, and develop methods, prevention measures and standards, which Europe is forced to use, since nothing similar exists for a network and combined knowledge to design them according to european standards. This makes Europe extremely dependent and, in some cases, the potential measures or standards cannot been used because the suggested solutions are prohibited by European laws (e.g. use of biocides). Therefore, it is important to initiate a new European MIC-network. Europe needs to combine the efforts as experts in different fields and develop prevention measures according to the European rules, in close cooperation with industry and plant operators and owners of critical infrastructure. This COST Action will provide the necessary interaction and communication, knowledge sharing, training of personnel and of researchers of different disciplines. This will bring Europe to a leading role in this process, bringing ideas on an equal level with other nations, considering the values which are important for Europe and attitudes (e.g.environmental protection) and representing greater protection for people, property and the environment. The main aim and objective of the Action is to , in the context of MIC-research/control, encourage a fluent/synergistic collaboration/communication, closing the gap between materials scientists, engineers, microbiologists, chemists and integrity managers to encourage sufficient interaction between academia and industry. This Action will create a common MIC-Network, including the important stakeholders. T2 - EuroCorr CY - Online meeting DA - 19.09.2021 KW - COST Action KW - MIC KW - Interdisciplinary KW - Stakeholder KW - Academia PY - 2021 AN - OPUS4-53382 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Neue Erkenntnisse zur Deckschichtbildung von Zink an der Atmosphäre N2 - Die Untersuchungen und Ausführungen im Vortrag belegen, dass verfügbare Modellvorstellungen zur Beschreibung der Deckschichtbildung und Korrosion von Zink unter aktuellen atmosphärischen Bedingungen in Europa nicht mehr gültig sind und neu bewertet werden müssen. So können beispielsweise bisher verfügbare Prognosemodelle den Korrosionsfortschritt nicht mehr ausreichend beschreiben, da durch die Verringerung des Schwefeldioxidgehaltes der Luft veränderte Mechanismen vorliegen. T2 - Sitzung des GfKORR Arbeitskreises „Zink und Zinküberzügel“ CY - Online meeting DA - 28.09.2021 KW - Atmosphärische Korrosion KW - Deckschichtbildung KW - Gelartige Elektrolyte KW - Zink PY - 2021 AN - OPUS4-53410 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erning, Johann Wilhelm T1 - Risiken in der Trinkwasser-Installation: Das Regelwerk im Kontext von Planung, Bau und Betrieb N2 - Die Herangehensweise zur Bewertung von Risisken in der Trinkwasserinstallation im Zusammenhang mit den Vorgaben der neuen EU-Trinkwasserrihrlin werden diskutiert. Auswirkungen der Veränderungen auf die Wrkstoffauswahl werden gezeigt T2 - Die neue EU-Trinkwasserrichtlinie CY - Online meeting DA - 07.07.2021 KW - Korrosion KW - Trinkwasser-Installation KW - Hygiene PY - 2021 AN - OPUS4-52937 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, Julia T1 - Photoperception in plant- and rock-associated black fungi N2 - Fungi that share light-flooded habitats with phototrophs may profit from their excess photosynthetic products. Sunlight-associated stresses are however multiple: high temperatures, UV radiation with associated DNA damage, accumulation of reactive oxygen species (ROS), desiccation and osmotic stresses. Ascomycota dominating light-flooded habitats accurately sense and respond to changes in light using it as a cue to coordinate growth, stress responses as well as to establish pathogenic or symbiotic relationships. Two species from two light-flooded habitats – phyllosphere and sun-exposed solid surfaces – were analysed for their photoreceptor distribution. In both habitats phototroph-associated and black [dihydroxynaphthalene (DHN) melanin-containing] fungi are prevalent. This diversity was sampled with the plant-associated fungus Botrytis cinerea (Leotiomycetes), while Knufia petricola (Eurotiomycetes) was included as a typical biofilm-former on sun-exposed solid surfaces e.g. rocks, building facades, roofs, and solar panels. The analysis has shown that genomes of black fungi contain more photoreceptors than animal pathogens and saprophytes such as Aspergillus nidulans and Neurospora crassa1,2. B. cinerea that causes the grey mould disease by infecting the above-ground parts of more than 200 dicots has a highly sophisticated photosensory and signalling system that helps to avoid light and to locate susceptible hosts1. Rock-inhabiting Dothideomycetes and Eurotiomycetes including Knufia petricola possess equal numbers of photoreceptors along with the same set of protective metabolites i.e. melanin, carotenoids and mycosporines2. This similarity between black fungi from plant and rock surfaces suggests that photoperception and -regulation are important for sun-stressed fungi that receive nutrients through cooperation with phototrophs. CRISPR/Cas9-based genetic tools for manipulating K. petricola were established3 and are currently used for elucidating the functions of the different photoreceptors in the biology of rock-inhabiting fungi. This work was supported by the grant SCHU 2833/4-1 from the German Research Foundation (DFG) and internal funds of the BAM. T2 - 19th Congress of the European Society for Photobiology CY - Online meeting DA - 30.08.2021 KW - Fungi KW - Light KW - Extreme environments PY - 2021 AN - OPUS4-53191 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreiber, Frank T1 - Physiological and evolutionary consequences of exposing Pseudomonas aeruginosa to biocide-antibiotic combinations N2 - Antimicrobials can exert specific physiological effects when used in combination that are different from those when applied alone. These effects include physiological effects (i.e. synergy, antagonism and suppression) as well as evolutionary effects on the selection of resistant strains (i.e. cross-resistance and collateral sensitivity). While combination effects have been extensively mapped for antibiotic-antibiotic combinations, the combination effects of antibiotics with antimicrobials used as biocides or antiseptics have not been systematically investigated. Here, we investigated the physiological and evolutionary consequences of combinations of antibiotics (meropenem, gentamicin and ciprofloxacin) and substances used as biocides or antiseptics (octenidine, benzalkonium chloride, cetrimonium bromide, chlorhexidine, povidone-iodine, silver) on growth and selection of Pseudomonas aeruginosa. We find prevalent physiological combination effects with synergy occurring 6 times and antagonism occurring 10 times. The effects are specific to the antibiotic-biocide combination with meropenem showing a tendency for antagonism with biocides (6 of 7), while gentamicin has a tendency for synergy (5 of 7). A particular strong antagonism is apparent for the meropenem-chlorhexidine combination, for which we conducted an in-depth study on the underlying molecular mechanism using RNASeq. Moreover, we find widespread effects of the biocide-antibiotic combinations on selection of P. aeruginosa strains resistant to the antibiotics, including cross-resistance and collateral sensitivity. In conclusion, antibiotics and biocides or antiseptics exert physiological and evolutionary combination effects on the pathogen P. aeruginosa. These effects have consequences for the efficacy of both types of substances and for the selection of antimicrobial resistant strains in clinical applications with combined exposure (e.g. wound care, coated biomaterials). T2 - Antimicrobial Resistance in Biofilms and on Biomaterials CY - Online meeting DA - 10.06.2021 KW - Antimicrobial resistance KW - Antimicrobial coating KW - Biofilms PY - 2021 AN - OPUS4-53162 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Richter, Anja A1 - Mezera, Marek A1 - Buchberger, G. A1 - Krüger, Jörg A1 - Bonse, Jörn A1 - Heitz, J. A1 - Schwibbert, Karin T1 - Laser-processing – a tool to direct biofilm formation N2 - Using nanofiber-like cell appendages, secreted proteins and sugars, bacteria can establish initial surface contact followed by irreversible adhesion and the formation of multicellular biofilms, often with enhanced resistance towards antimicrobial treatment and established cleaning procedures. On e.g. medical implants, in water supply networks or food-processing industry, biofilms can be a fertile source of bacterial pathogens and are repeatedly associated with persisting, nosocomial and foodborne infections. Nowadays, the emergence of resistances because of extensive usage of antibiotics and biocides in medicine, agriculture and private households have become one of the most important medical challenges with considerable economic consequences. In addition, aggravated biofilm eradication and prolonged cell-surface interaction can lead to increased biodeterioration and undesired modification of industrial and medical surface materials. Various strategies are currently developed, tested, and improved to realize anti-bacterial surface properties through surface functionalization steps avoiding antibiotics. In this study, contact-less and aseptic large-area short or ultrashort laser processing is employed to generate different surface structures in the nanometer- to micrometer-scale on technical materials such as titanium-alloy and polyethylene terephthalate (PET). The laser processed surfaces were subjected to bacterial colonization studies with Escherichia coli test strains and analyzed with reflected-light and epi-fluorescence microscopy. Depending on the investigated surfaces, different bacterial adhesion patterns were found, ranging from bacterial-repellent to bacterial-attractant effects. The results suggest an influence of size, shape and cell appendages of the bacteria and – above all – the laser-processed nanostructure of the surface itself, emphasizing the potential of laser-processing as a versatile tool to control bacterial surface adhesion. T2 - International Biodeterioration & Biodegradation Symposium 2021 CY - Online meeting DA - 06.09.2021 KW - Bacterial adhesion KW - Biofilm formation KW - Laser-induced periodic surface structueres (LIPPS) KW - Laser processing PY - 2021 UR - https://www.ibbs18.org/programme AN - OPUS4-53223 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Neue Erkenntnisse zur Deckschichtbildung von Zink an der Atmosphäre N2 - Die Untersuchungen und Ausführungen im Vortrag belegen, dass verfügbare Modellvorstellungen zur Beschreibung der Deckschichtbildung und Korrosion von Zink unter aktuellen atmosphärischen Bedingungen in Europa nicht mehr gültig sind und neu bewertet werden müssen. So können beispielsweise bisher verfügbare Prognosemodelle den Korrosionsfortschritt nicht mehr ausreichend beschreiben, da durch die Verringerung des Schwefeldioxidgehaltes der Luft veränderte Mechanismen vorliegen. T2 - Sitzung des GfKORR Arbeitskreises „Korrosion und Korrosionsschutz von Eisen und Stahl“ CY - Online meeting DA - 22.06.2021 KW - Atmosphärische Korrosion KW - Gelartige Elektrolyte KW - Deckschichtbildung KW - Zink PY - 2021 AN - OPUS4-52843 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seneschal-Merz, Karine A1 - Bücker, Michael A1 - Wachtendorf, Volker A1 - Heidrich, Christa A1 - Sander, Christoph T1 - New UV-protective glazing for the conservation of cultural assets N2 - For centuries, churches, secular buildings and museums have been furnished with valuable works of art. Many works of art are UV- and light-sensitive. It is well known that especially UV radiation causes damage and discoloration in paintings, textiles, plastics, wood and other materials. In particular, the wavelengths between 280 and 410 nm cause color changes, embrittlement or destruction of e.g. plastics over time. Therefore, strongly UV-absorbing glasses are advantageous for architecture and are necessary for the protection of cultural assets. As restorers in all disciplines become more and more aware, the demands placed on buildings and their furnishings in terms of climate are becoming increasingly detailed and precise. The aim in each case is to preserve the valuable artwork. For some years now, the industry has been offering the protection of cultural objects by installing special UV-protective glasses. Currently, UV protection for church buildings is realized by laminated safety glass equipped with appropriate UV-protective plastic films. Technically, this always means a second pane of glass in front of the windows, which is installed outside the building. This creates climatic gaps that are difficult to control and deterioration due to ageing effects can be expected. At the same time, this protective glazing is not invisible and has a considerable aesthetic influence on the interior and exterior appearance of the building. Meanwhile, the preservation of historical monuments accepts such aesthetic cuts on buildings in order to protect the artwork in the interior from UV light. To this day, however, the long-term durability of UV protection provided by inserted plastic films is still controversial. To date the only available alternative on the market is a mouth-blown UV protection glass which uses a so-called overlay to provide UV protection. This shows that UV protection can also be achieved by glasses without plastic films thus realizing an exclusive inorganic protection which normally is more stable than a polymeric one. So far there are not enough studies to prove long-term durability. The aim of this project is to provide existing glazing or new glazing to be created with a highly transparent layer that ensures this UV-protective filter function below 400 nm. The glass coating is to be applied to the glass over a large area and fired into the surface like a classic ceramic enamel paint with the same technics. In addition, it should be long-term durable in its function. It means, that the glass has to be fused at temperatures below 630 °C during the firing process, its chemical durability has to be high, its coefficient of thermal expansion has to be as close as the one of the substrate (usually float glass) and the glass has to absorb the UV-radiation within a thin thickness (thinner as 100 µm). In this project, the long-term durability of commercial UV-protective glasses is examined. New low melting glasses containing UV-absorbing ions are being developed. Their UV-absorption as a thin layer is analyzed as well as their chemical durability and their thermal properties. We are grateful to BMWI for the financial support in the frame of the Central Innovation Programme for SMEs (ZIM). T2 - HVG-DGG: 94. Glastechnische Tagung CY - Online meeting DA - 10.05.2021 KW - Glass KW - Low melting KW - Chemical durability KW - Weathering tests KW - Aging test KW - UV absorption KW - UV protection KW - Architecture KW - Optical properties PY - 2021 AN - OPUS4-52648 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dinter, Adelina-Elisa A1 - An-Stepec, Biwen A1 - Wurzler, Nina A1 - Koerdt, Andrea A1 - Meermann, Björn T1 - Development of a single cell-ICP-ToF-MS-method for multielement analysis of MIC organisms grown on solid steel samples N2 - The latest ICP-MS technology - ICP-ToF (time of flight)-MS – enables the analysis of the multi-element fingerprint of individual cells. The interface between material and environmental analysis thus receives special attention, e.g., when considering corrosion processes. Microbiologically influenced corrosion (MIC) is a highly unpredictable phenomenon due to the influence of the environment, microbial communities involved and the respective electron source. However, the interaction pathway between cells and the metal surface remains unclear. The development of the MIC-specific ICP-ToF-MS analytical method presented here at the single cell level, in combination with the investigation of steel-MIC interactions, contributes significantly to progress in instrumental MIC analysis and will enable clarification of the processes taking place. For this, a MIC-specific staining procedure was developed. It allows the analysis of archaea at a single cell level and provides information about the interaction of the cells with the staining agent which is extremely scarce compared to other well characterized organisms. Additionally, the single cell ICP-ToF-MS is used for the analysis of archaea involved in MIC of steel. Hence, the possible uptake of individual elements from different steel samples is investigated - the information obtained will be used in the future to elucidate underlying mechanisms and develop possible material protection concepts, thus combining modern methods of analytical sciences with materials. T2 - DAAS Doktorandenseminar 2021 CY - Online meeting DA - 20.09.2021 KW - Sc-ICP-ToF-MS KW - Single cell analysis KW - Microbiologically influenced corrosion KW - Archaea PY - 2021 AN - OPUS4-53340 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin A1 - Müller, Thoralf T1 - Field exposure studies under sheltered and unsheltered conditions at different test sites in northern and eastern Germany: Update after 5 years of exposure N2 - A series of field exposure tests according to ISO 9223 up to 9226 was carried out at different locations to determine the corrosivity and the corrosion progress of different test sites throughout northern and eastern Germany. Standard test specimens of steel, zinc, copper and aluminium were exposed to rural, city and marine atmosphere at test sites of the Bundesanstalt für Materialforschung und -prüfung (BAM). Test sites at city atmosphere comprised exposure on a rooftop, next to a highly frequented road and directly at a motorway. Exposure under marine conditions was carried out at Heligoland in the North Sea. The specimens were stored under sheltered and unsheltered conditions on each test site, respectively. Corrosion rates after the first year of field exposure were determined and used for the classification of the atmospheres and the test sites regarding the corrosivity category. Results after the first year of exposure were presented at the EUROCORR 2018 in Cracow. The current presentation will present an update of results of the systematic study after five years of exposure. The corrosion progress and the mass loss of the standard metals steel, zinc, copper and aluminium will be presented and discussed with respect to the atmospheric conditions and the time of wetness at the test sites. In addition, the difference between sheltered and unsheltered conditions will be discussed. T2 - EUROCORR 2022 CY - Berlin, Germany DA - 28.08.2022 KW - Atmospheric Corrosion KW - Atmosphärische Korrosion KW - Korrosionsuntersuchungen KW - Corrosion testing PY - 2022 AN - OPUS4-55602 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreiber, Frank T1 - Resistance evolution towards biocides and antimicrobial surfaces N2 - Biocides, including disinfectants and antimicrobial surfaces (AMCs), are important to prevent the spread of pathogens and antimicrobial resistant bacteria via surfaces. However, concerns have been raised about the evolution and selection of resistance against disinfectants and AMCs. In turn, resistance against disinfectants and AMCs can be associated to antibiotic resistance due to cross-resistance and co-resistance. We need to understand the mechanisms and risks of disinfectants and AMCs for resistance and cross-resistance evolution to optimize their application and safeguard their long-term efficacy. We used adaptive laboratory evolution (ALE) experiments based on repeated exposure of bacteria to disinfectants. Our results show that repeated disinfection of E. coli with benzalkonium chloride in suspension results in a 2000-fold increase in survival within 5 exposure cycles. Adaption is linked to the initial presence of persister cells highly tolerant to benzalkonium chloride. We used the same approach to develop standardizable ALE experiments to determine resistance evolution to AMCs. The results highlight rapid adaptation of E. coli and P. aeruginosa towards copper surfaces. Moreover, there are multiple situations in the clinic or in the environment in which biocides and antibiotics co-occur and in which combination effects can shape their antimicrobial activity or their selective effects. Our work with P. aeruginosa shows prevalent combination effects of biocides and antibiotics, ranging from synergy to antagonism and resulting in the selection for or against antibiotic resistant strains. The combination effects are dependent on the biofilm mode-of-growth, manifesting in apparent differences in the structural arrangement of antibiotic sensitive and resistant strains in biofilms exposed to combinations. Furthermore, biocides affect rates of mutation and horizontal gene transfer, thereby having a potential facilitating effect on resistance evolution. Taken together, our work shows that the role of biocides as potential drivers of resistance evolution and selection deserves further study and regulative action. T2 - Eurobiofilms 2022 CY - Palma, Spain DA - 31.08.2022 KW - Antimicrobial resistance KW - Bacteria KW - Biofilms KW - Biocides KW - Antimicrobial surfaces PY - 2022 AN - OPUS4-55608 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Haacke, Nasrin A1 - Babutzka, Martin T1 - Vorstellung des Forschungsprojektes RUNOFF: "Neubewertung der Dauerhaftigkeit von Dach- und Fassadenmaterialien und des Eintrags von Schwermetallionen in die Umwelt hervorgerufen durch Runoff„ N2 - Der Vortrag stellt das Forschungsprojekt RUNOFF vor und geht auf das geplante Arbeitsprogramm ein. Darüber hinaus wird die Problemstellung erläutert. T2 - Klempnerfachtagung des Zentralverbands Sanitär-Heizung-Klima CY - Karlstadt a. M., Germany DA - 11.10.2022 KW - Korrosion KW - Kupfer KW - Runoff KW - Zink KW - Atmosphärische Korrosion PY - 2022 AN - OPUS4-56045 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erning, Johann Wilhelm T1 - Risiken in der Trinkwasserinstallation N2 - Die neue Trinkwasserrichtlinie gibt erweiterte Vorgaben zu Risikobewertungen in der gesamtemn kette von der Aquelle zum Zapfhahn. Der Vortrag beschreibt das präventive Konzept der Risikovermeidung über bewertete Werkstoffe und das Regelwerk. T2 - 19. Erfahrungsaustausch Trinkwasserverordnung CY - Brandenburg, Germany DA - 10.10.2022 KW - Korrosion KW - Trinkwasser KW - hygienische Bewertung KW - Risikobewertung PY - 2022 AN - OPUS4-55981 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erdmann, Eileen A1 - Kunze, R. A1 - Gorbushina, Anna A1 - Schumacher, Julia T1 - Tools for Reverse and Forward Genetics in Knufia petricola N2 - Microcolonial black fungi are inhabitants of exposed natural and man-made surfaces in all climate zones. Genetic studies are hampered by slow growth, lacking sexual cycles and difficulties to transform these fungi. Recently, we implemented CRISPR/Cas9-based genetic tools enabling efficient targeted mutations of the rock inhabitant Knufia petricola (Eurotiomycetes/Chaetothyriales) for studying stress responses, the unusual types of cell division, mineral weathering and symbiotic interactions with phototrophic microbes (Voigt, Knabe et al. 2020, Sci Rep; Erdmann et al. 2022, Front Fungal Biol). To further explore the genome of this fungus as representative of the polyphyletic group of black fungi and to assign functions to yet unknown genes, a forward genetics approach is aimed. We chose the two-component Activator/ Dissociation (Ac/Ds) transposon system from maize for generating a collection of insertional mutants by in-vivo mutagenesis. For the optimal use of this genetic tool, an inducible promoter for the expression of the Ac transposase and by this the regulatable transposition of the resistance cassette-containing Ds transposon is requested. However, endogenous promoters for nitrate assimilation and galactose catabolism that are often used in fungi for regulatable gene expression are not inducible by their substrates in K. petricola suggesting that the regulatory networks for nutrient acquisition differ significantly in the oligotrophic black fungi. Therefore, the metabolism-independent Tet-on system was adopted and validated using a Ptet::gfp construct. No GFP fluorescence was detected in absence of the inducer doxycycline (DOX) while fluorescence intensities increased with increasing inducer concentrations. Consequently, the Tet-on system is suitable for regulatable expression of endogenous and foreign genes in K. petricola. T2 - VAAM Fachgruppentagung "Molecular Biology of Fungi" CY - Kaiserslautern, Germany DA - 07.09.2022 KW - Rock-inhabiting fungus KW - Genetic tools KW - Controllable gene expression PY - 2022 AN - OPUS4-55678 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kotula, Stefan A1 - Babutzka, Martin A1 - Groth, L. T1 - Zinkbeizen nach alter ISO 8407 N2 - Der Vortrag beschäftigt sich mit der Problemstellung der Entfernung von Korrosionsprodukten auf Zinkoberflächen zur Bewertung des Masseverlustes. Er diskutiert die Diskrepanzen zwischen der alten Version der ISO 8407 und der aktuellen Version. T2 - Sitzung des DIN-Gemeinschaftsarbeitskreises NA 062 01 77 01 GAK CY - Online Meeting DA - 22.09.2022 KW - Atmosphärische Korrosion KW - Deckschichtbildung KW - ISO 8407 KW - Korrosion PY - 2022 AN - OPUS4-55807 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Babutzka, Martin T1 - Vorstellung des Konzeptes und der Ziele des Arbeitskreises „Atmosphärische Korrosion“ N2 - Der Vortrag wurde im Rahmen der konstituierenden Sitzung des Arbeitskreises "Atmosphärische Korrosion" der GfKORR - Gesellschaft für Korrosionsschutz e.V. gehalten. Er stellt die zur Diskussion stehenden Fragestellungen und Herausforderungen im Bereich der atmosphärischen Korrosion zusammen, denen sich der neue Arbeitskreis widmen wird. T2 - Konstituierende Sitzung des GfKORR-Arbeitskreises „Atmosphärische Korrosion“ CY - Frankfurt a. M., Germany DA - 19.09.2022 KW - Atmosphärische Korrosion KW - Korrosion KW - Korrosionsschutz PY - 2022 AN - OPUS4-55772 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlegel, Moritz-Caspar T1 - Normungsroadmap Circular Economy - Highlights N2 - Eines haben die Krisen dieses Jahrzehnts gemeinsam: Sie motivieren zum Handeln. Bezüglich der Klimakrise wird eine grundlegende Änderung unseres Wirtschaftens als wesentlicher Lösungsweg gesehen. Die aktuell praktizierte lineare Wertschöpfung führte zu Ressourcenknappheit und -abhängigkeit und trug aktiv zur Verstärkung des Klimawandels bei. Wie wir in diesem Jahrzehnt unseren Absprung von gewohnten Produktions-, Konsum- und Verwertungsmustern gestalten, wird entscheidend für die nächsten Jahrzehnte sein. Die Frage, wie bis 2030 die Transformation hin zu einer zirkulären Wirtschaft gelingen kann, wurde u.a. von der Circular Economy Initiative Deutschland beantwortet. Sie nennt zehn Handlungsschwerpunkte, wobei „Standardisierung“ mit an wichtigster Stelle steht. Dieses beruht auf Gegenseitigkeit. Auf der diesjährigen G7 Standardisation High-level Conference wurde Circular Economy zu dem Themabereich mit dem größten Potential für Klimaschutzmaßnahmen gesehen. In 2022 haben DIN, DKE und VDI mit über 500 Fachexperten aus Wirtschaft, Wissenschaft und Politik an einer Normungsroadmap Circular Economy gearbeitet. Die BAM war in fünf von sieben Schwerpunktthemen beteiligt. Ziel der Roadmap ist es, einen Handlungsrahmen für die Normung und Standardisierung zu schaffen, der die Transformation hin zu einer Circular Economy fördert. Normen und Standards bilden den untergesetzlichen und technischen Rahmen, auf denen eine zirkuläre Wirtschaft aufwachsen kann. Sie definieren Schnittstellen und stellen eine klare Kommunikation zwischen den verschiedenen Phasen des zirkulären Kreislaufes sicher – sie machen einen Kreislauf erst möglich. In der Präsentation sind die Highlights der Normungsroadmap Circular Economy dargestellt. Die Roadmap liefert einen Überblick über die aktuelle Normungslandschaft sowie die An- und Herausforderungen zu Schwerpunktthemen wie Elektrotechnik, Kunststoffe, Verpackungen, Textilien, Bauwerke, etc. Mit >250 Normungs- und Standardisierungsbedarfen zeigt die Roadmap konkrete Handlungsfelder auf, ebenfalls mit Überschneidungen zum Geschäftsfeld der BAM. T2 - Abteilungsseminar Abteilung S CY - Berlin, Germany DA - 11.01.2023 KW - Circular Economy KW - Kreislaufwirtschaft KW - Normungsroadmap KW - Klimawandel PY - 2023 AN - OPUS4-56817 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dehkohneh, Abolfazl A1 - Gorbushina, Anna A1 - Gerrits, Ruben T1 - Modelling biofilm formation and material colonisation for Knufia petricola N2 - Rock-inhabiting black fungi are adapted to survive extreme stresses such as radiation and lack of water and are thus able to colonise arid material surfaces like solar panels and marble monuments. Black fungi can typically grow as one of two cell types: depending on the environmental conditions, they are able to form yeast-like cells or hyphal filaments. Knufia petricola is one member of the rock-inhabiting black fungi which functions as a model reference species. As there is no mathematical model for biofilm formation of RIF, we are going to develop a model for K. petricola which describes fungal growth on the level of individual cells adn biofilm formation. T2 - Mini conference at University of Birmingham CY - Birmingham, UK DA - 05.10.2022 KW - Knufia petricola KW - Rock-inhabiting black fungi KW - individual-based modelling PY - 2022 AN - OPUS4-56697 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dümichen, Erik A1 - Eisentraut, Paul A1 - Braun, Ulrike T1 - Fast identification of microplastics using thermal extractions methods N2 - A new and full automated system for the analysis of microplastics in environmental samples is presented. T2 - BAM-BfR Seminar 2018 CY - Berlin, Germany DA - 15.02.2018 KW - Mikroplastik KW - TED KW - Thermal degradation PY - 2018 AN - OPUS4-44179 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Braun, Ulrike T1 - Fast identification of microplastics using thermal extraction methods N2 - The presentation presents an overview about existing methods of microplastic detection with a special focus on thermo-analytical methods. T2 - Perkin Elmer Workshop Microplastics CY - Vienna, Austria DA - 11.01.2018 KW - Microplastics KW - TED-GC-MS KW - Analysis PY - 2018 AN - OPUS4-43803 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute T1 - Tools for the characterization of secondary raw materials - status of leaching test application N2 - Leaching tests are used as tools for the assessment of environmental compatibility of granular waste materials with potential for reuse. The presentation gives an overview on available leaching tests, their field of application and relation to legislation. Furthermore robustness testing to elaborate optimized test conditions as well as performance characteristics from validation studies by BAM are addressed. T2 - Travelling Conference CY - Perth, Australia DA - 06.02.2018 KW - Leaching KW - Risk assessment KW - Robustness studies PY - 2018 AN - OPUS4-44723 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute T1 - Tools for the characterization of secondary raw materials - status of leaching test application N2 - Leaching tests are used as tools for the assessment of environmental compatibility of granular waste materials with potential for reuse. The presentation gives an overview on available leaching tests, their field of application and relation to legislation. Furthermore robustness testing to elaborate optimized test conditions as well as performance characteristics from validation studies by BAM are addressed. T2 - Travelling Conference CY - Ho-Chi-Ming City, Vietnam DA - 01.02.2018 KW - Leaching KW - Risk assessment KW - Robustness studies PY - 2018 AN - OPUS4-44724 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute T1 - Tools for the characterization of secondary raw materials - status of leaching test application N2 - Leaching tests are used as tools for the assessment of environmental compatibility of granular waste materials with potential for reuse. The presentation gives an overview on available leaching tests, their field of application and relation to legislation. Furthermore robustness testing to elaborate optimized test conditions as well as performance characteristics from validation studies by BAM are addressed. T2 - Travelling Conference CY - Seoul, Korea DA - 29.01.2018 KW - Leaching KW - Risk assessment KW - Robustness studies PY - 2018 AN - OPUS4-44725 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute A1 - Schatten, René A1 - Szuppa, Tony T1 - Untersuchungen von Bodenmaterialien auf mobilisierbare organische Stoffanteile im Elutionsmethodenvergleich N2 - Im Beitrag wurden erste Ergebnisse eines laufenden UFOPLAN-Vorhabens zu den neuen Kriterien der Verwertungsmöglichkeiten von Bodenmaterialien außerhalb der durchwurzelbaren Bodenschicht nach den §§ 6 bis 8 der Novelle der BBodSchV vorgestellt. Der Schwerpunkt lag auf Untersuchungen der Schadstoffgruppe der PAK. Dabei wurden Probleme der Vergleichbarkeit und Leistungsfähigkeit verschiedener Elutions- und Analyseverfahren der PAK-Analytik diskutiert. T2 - Fachgespräch Feststoffuntersuchungen CY - Essen, Germany DA - 06.03.2018 KW - Leaching KW - PAK KW - Böden PY - 2018 AN - OPUS4-44726 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kalbe, Ute A1 - Piechotta, Christian T1 - Vergleich von Elutionsuntersuchungen auf perfluorierte Chemikalien (PFC) N2 - Im Beitrag wurden Ergebnisse von Elutionsuntersuchungen mit PFC kontaminierten Bodenmaterialien vorgestellt. Zum einen waren das Untersuchungen zur Eignung von Säulenversuchen für diese Schadstoffgruppe und zum anderen vergleichende Schüttel- und Säulenversuche für zwei verschiedene Böden mit unterschiedlichen PFC-Kontaminationsquellen. T2 - Fachgespräch Feststoffuntersuchungen CY - Essen, Germany DA - 05.03.2018 KW - Leaching KW - PFC KW - Böden PY - 2018 AN - OPUS4-44727 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schoknecht, Ute A1 - Bandow, Nicole T1 - Auswaschversuche zur Charakterisierung der Umweltverträglichkeit von Bauprodukten N2 - Im Vortrag werden Auswaschversuche mit Bauprodukten vorgestellt, die dazu dienen sollen, Bauprodukte mit geringer Auswaschung zu erkennen. Zu verschiedenen Bauprodukten (Lacke für Außenanwendungen, Wärmedämmverbundsystemen, Dachziegel und Dachfolien) werden ausgewählte Ergebnisse vorgestellt. Die Eignung der Auswaschverfahren und die Testergebnisse werden bewertet. T2 - Umwelteigenschaften von Bauprodukten: Schnellbewitterung, Leaching, Modellierung CY - Holzkirchen, Germany DA - 17.04.2018 KW - Testverfahren KW - Auswaschversuche KW - Bauprodukte PY - 2018 AN - OPUS4-44734 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schreiber, Frank T1 - Phenotypic diversity in microbial metabolism and antimicrobial resistance N2 - Most microorganisms live in environments where nutrients are limited and fluctuate over time. Cells respond to nutrient fluctuations by sensing and adapting their physiological state. Recent studies suggest phenotypic heterogeneity in isogenic populations as an alternative strategy in fluctuating environments, where a subpopulation of cells express a function that allows growth under conditions that might arise in the future. It is unknown how environmental factors such as nutrient limitation shape phenotypic heterogeneity in metabolism and whether this allows cells to respond to nutrient fluctuations. Here, we show that substrate limitation increases phenotypic heterogeneity in metabolism, and this heterogeneity allows cells to cope with substrate fluctuations. We subjected the N2-fixing bacterium Klebsiella oxytoca to different levels of substrate limitation and substrate shifts, and obtained time-resolved single-cell measurements of metabolic activities using nanometre-scale secondary ion mass spectrometry (NanoSIMS). We found that the level of NH4+ limitation shapes phenotypic heterogeneity in N2 fixation. In turn, the N2 fixation rate of single cells during NH4+ limitation correlates positively with their growth rate after a shift to NH4+ depletion, experimentally demonstrating the benefit of heterogeneity. The results indicate that phenotypic heterogeneity is a general solution to two important ecological challenges - nutrient limitation and fluctuations - that many microorganisms face. Currently, we use NanoSIMS to develop a new approach that defines functionally-relevant, phenotypic biodiversity in microbial systems. In the last part of my presentation, I will highlight why the concept of phenotypic diversity is relevant for the understanding of antimicrobial resistance. T2 - Berlin Seminar for Resistance Research at FU Berlin Veterinary Medicine CY - Berlin, Germany DA - 01.03.2018 KW - Antimicrobial Resistance KW - Metabolism KW - Phenotypic diversity PY - 2018 AN - OPUS4-44597 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Braun, Ulrike T1 - Analytik von Mikroplastik mittels TED-GC-MS N2 - Der Vortrag stellt spektroskopische und neue thermoanalytische Verfahren zum Nachweis von Mikroplastik dar. Ein spezieller Focus ist auf der Anwendung edr Verfahren für terrestrische Proben. T2 - Fachgespräch Feststoffuntersuchungen 2018 CY - Essen Werden, Germany DA - 05.03.2018 KW - Mikroplastik KW - Analytik KW - GC-MS KW - Thermische Analyse PY - 2018 AN - OPUS4-44525 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Paul, Andrea T1 - A process spectroscopic approach for the monitoring of microplastics  in environmental samples N2 - The potential of Raman and NIR process-spectroscopic as a rapid approach for the estimation of microplastics (MP) in soil matrix were tested. For this purpose, artificial MP/soil mixture samples consisting of standard soils or sand with defined ratios of MP (0,5 – 10 mass% polymer) from polyethylene (PE), polypropylene (PP), polystyrene (PS) and polyethylene terephthalate (PET) were prepared. MP particles with diameters < 2 mm and < 125 µm were obtained from industrial polymer pellets after cryo-milling. Spectra of these mixtures were collected by (i) a process FT-NIR spectrometer equipped with a reflection probe, (ii) by a cw-process Raman spectrometer and (iii) by a time-gated Raman spectrometer using fiber-optic probes. The evaluation of process-spectra was performed by chemometric methods. Whereas MP could be detected by Raman spectroscopy in coastal sand at 0.5 mass%, in standard soil detection of MP was limited to 10 – 5 mass% with the large fraction, but samples containing particles of the 125µm mass-fraction yielded no positive result at all. One reason for the lacking sensitivity could be fluorescence by soil organic matter and thus, in a next test time-gated Raman spectroscopy was applied. However, although being indeed more sensitive to the small particles this method failed at MP < 5 mass% indicating that fluorescence was not the major problem. Finally, FT-NIR was tested. Depending on the polymer, MP contents of 0,5 or 1 mass%, respectively, could be detected in standard soils and polymers identified. Furthermore, this approach could be used for the investigation of mixtures of up to four polymers and in real-world samples from bio-waste fermenter residues. T2 - Einladung zu einem Beratungsgespräch zum Thema Mikroplastik durch die Firma Endress+Hauser Conducta GmbH+Co.KG CY - Gerlingen, Germany DA - 11.06.2018 KW - Chemometrics KW - Microplastics KW - Raman KW - Process-spectroscopy KW - NIR PY - 2018 AN - OPUS4-45406 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Braun, Ulrike A1 - Klöckner, P. A1 - Wagner, S. A1 - Ruhl, A.S. A1 - Eisentraut, Paul A1 - Albrecht, M. A1 - Reemtsma, T. T1 - Identification of tire wear particles based on elemental composition N2 - The identification of tire wear particles by use of ICP-MS is presented. T2 - SETAC CY - Rome, Italy DA - 13.05.2018 KW - Microplastics KW - Tire wear particles KW - ICP-MS PY - 2018 AN - OPUS4-45205 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Braun, Ulrike A1 - Bannick, C. G. T1 - Sampling, sample preparation and detection of microplastics, current activities in the ISO/TC 61/SC14/WG 4 N2 - Presentation about the actual status of microplastic research in BAM and UBA, activities in Germany and ISO/TC61/SC14. T2 - Microplastic Methodes Workshop CY - London, UK DA - 23.05.2018 KW - Microplastics KW - TED-GC-MS KW - Analysis KW - Standardisation PY - 2018 AN - OPUS4-45033 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver T1 - Emissionsarme Materialien und Produkte für eine saubere Innenraumluft N2 - Mit dem Fokus auf eine saubere Innenraumluft wird darauf eingegangen, welche Emissionen aus Materialien und Produkten es gibt und wie sie nach Art und Flüchtigkeit definiert sind und wie sie gemessen werden. Im weiteren wird dargestellt, was und wie viel aus Materialien und Produkten emittieren kann und wie die Emissionen zu bewerten sind. Hierbei wird auch auf besonders emissionsarme Materialien und Produkte eingegangen. T2 - Kolloquium am Institut für Technischen Umweltschutz, Sommersemester 2018 CY - Berlin, Germany DA - 28.05.2018 KW - Emissionen KW - Luft KW - VOC KW - Aerosol KW - Radon KW - Geruch PY - 2018 AN - OPUS4-45052 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bandow, Nicole T1 - Consideration of organic contaminants and ecotoxicologal impact of recycling materials - Handling of substances without treshold values N2 - The presentation gives an overview about the use of ecotoxicity testing in assessment of waste. Especially in cases with unknown composition this kind of test are useful. Recently, the assessment of the hazard property HP 14 "ecotoxicity" for the labelling of waste was published. The labelling procedure is explained in detail. T2 - Travelling Conference CY - Perth, Australia DA - 06.02.2018 KW - Ecotoxicity KW - HP14 KW - Recycling materials PY - 2018 AN - OPUS4-44456 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Aktuelle Diskussionen zur vorläufigen Zulassungsrichtlinie von Bewehrungsgittern für Deponieoberflächenabdichtungen und zu Auftragsnähten in Kunststoffdichtungsbahnen N2 - Die BAM wurde 2009 u. a. mit der Zulassung von Bewehrungsgittern für den Deponiebau beauftragt. Der Stand von Wissenschaft und Technik bot jedoch keine ausreichende Grundlage, die tatsächlich relevanten Widerstände und die mit diesen Widerständen verbundene Wechselwirkung zwischen Gitter und Boden im Hinblick auf eine mindestens 100-jährige Funktionsdauer realistisch beurteilen zu können. Es wurde daher nur eine vorläufige Zulassungsrichtlinie für diese Produkte erarbeitet. In der Zwischenzeit hat sich ein neuer Kenntnisstand ergeben. Vor diesem Hintergrund hat die AG (Arbeitsgruppe) Geogitter des Fachbeirats der BAM am 26.09.2017 getagt. Es sollen die aktuellen Erkenntnisse und Schlussfolgerungen für die Zulassung in Kürze vorgestellt werden. Die entsprechenden Kapitel beruhen dabei auf einem Arbeitspapier von W.W. Müller und dem Autoren, das der Arbeitsgruppe zur Diskussion vorgelegt wurde. Weiterhin soll über Entwicklungen in Zusammenhang mit Kunststoffdichtungsbahnen (KDB) berichtet werden. Die Anforderungen an die Schweißzusätze für das Extrusionsschweißen wurden angepasst. Zudem soll über die aktuelle Diskussion der Schweißbarkeit unterschiedlicher HDPE Materialien informiert werden. Die maßgebliche DVS (Deutscher Verband für Schweißen und verwandte Verfahren) Richtlinie 2225-4 wird derzeit offenbar so ausgelegt, dass Materialien mit völlig unterschiedlichen Schmelze-Massefließrate miteinander verbunden werden können. Dies steht allerdings im grundlegenden Widerspruch zum Stand der Technik. T2 - 14. Leipziger Deponiefachtagung - Planung, Bau, Betrieb, Stilllegung, Nachsorge und Nachnutzung von Deponien CY - Leipzig, Germany DA - 06.03.2018 KW - Bewehrungen aus Kunststoff KW - Kunststoffschweißen KW - Deponietechnik PY - 2018 AN - OPUS4-44418 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bandow, Nicole T1 - Consideration of organic contaminants and ecotoxicologal impact of recycling materials - Handling of substances without treshold values N2 - The presentation gives an overview about the use of ecotoxicity testing in assessment of waste. Especially in cases with unknown composition this kind of test are useful. Recently, the assessment of the hazard property HP 14 "ecotoxicity" for the labelling of waste was published. The labelling procedure is explained in detail. T2 - Travelling Conference CY - Seoul, Korea DA - 29.01.2018 KW - Ecotoxicity KW - Recycling materials KW - HP14 PY - 2018 AN - OPUS4-44454 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bandow, Nicole T1 - Consideration of organic contaminants and ecotoxicologal impact of recycling materials - Handling of substances without treshold values N2 - The presentation gives an overview about the use of ecotoxicity testing in assessment of waste. Especially in cases with unknown composition this kind of test are useful. Recently, the assessment of the hazard property HP 14 "ecotoxicity" for the labelling of waste was published. The labelling procedure is explained in detail. T2 - Travelling Conference CY - Ho-Chi-Ming City, Vietnam DA - 01.02.2018 KW - Ecotoxicity KW - HP14 KW - Recycling materials PY - 2018 AN - OPUS4-44455 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lauer, Franziska A1 - Diehn, Sabrina A1 - Weidner, Steffen A1 - Kneipp, Janina T1 - A graphical user interface for a fast multivariate classification of MALDI-TOF MS data of pollen grains N2 - The common characterization and identification of pollen is a time-consuming task that mainly relies on microscopic determination of the genus-specific pollen morphology. A variety of spectroscopic and spectrometric approaches have been proposed to develop a fast and reliable pollen identification using specific molecular information. Amongst them, matrix-assisted laser desorption/ionization time-of-flight mass spectrometry (MALDI-TOF MS) shows a high potential for the successful investigation of such complex biological samples. Based on optimized MALDI sample preparation using conductive carbon tape, the application of multivariate statistics (e.g. principal components analysis, PCA) yields an enormous improvement concerning taxonomic classification of pollen species compared to common microscopic techniques. Since multivariate evaluation of the recorded mass spectra is of vital importance for classification, it’s helpful to implement the applied sequence of standard Matlab functions into a graphical user interface (GUI). In this presentation, a stand-alone application (GUI) is shown, which provides multiple functions to perform fast multivariate analysis on multiple datasets. The use of a GUI enables a first overview on the measured dataset, conducts spectral pretreatment and can give classification information based on HCA and PCA evaluation. Moreover, it can be used to improve fast spectral classification and supports the development of a simple routine method to identify pollen based on mass spectrometry. T2 - 12. Interdisziplinäres Doktorandenseminar, GDCh AK Prozessanalytik CY - BAM, AH, Berlin, Germany DA - 25.03.2018 KW - MALDI KW - GUI KW - Pollen PY - 2018 AN - OPUS4-44661 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erning, Johann Wilhelm T1 - Werkstoffe im Kontakt mit Trinkwasser - Was ist wie geregelt? N2 - Es wird eine Einführung in die Korrosion gegeben, dazu die Beschreibung der Verfahren zur Qualifizierung von Werkstoffen. Mess- und Bewertungsverfahren werden dargestellt. T2 - Kolloquium der Abteilung 1 "Mechanik und Akustik" der PTB CY - Braunschweig, Germany DA - 31.01.2018 KW - Korrosion KW - Metallabgabe KW - Metallene Werkstoffe PY - 2018 AN - OPUS4-44712 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bandow, Nicole A1 - Schoknecht, Ute T1 - Auswaschung aus Wärmedämmverbundsystemen N2 - Ausgewählte Ergebnisse des UBA-Vorhabens "Beregnete Bauteile und Bauprodukte: Entwicklungen für Vergabegrundlagen für den Blauen Engel mit Hilfe von Auslaugtest" werden für organische und anorganische Analyten präsentiert. Ein Schwerpunkt ist den Einfluss der verschiedenen Schichten von WDVS-Systemen aufzuzeigen. T2 - UBA Fachgespräch "Umwelteigenschaften von Bauprodukten: 'Schnellbewitterung, Leaching, Modellierung CY - Valley, Germany DA - 17.04.2018 KW - Auswaschung KW - DSLT KW - Tauchtest KW - Wärmedämmverbundsystem PY - 2018 AN - OPUS4-44720 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bresch, Harald T1 - OECD Prüfrichtlinie für die Größenbestimmung von Nanomaterialien N2 - Erste Ergebnisse des Projektes "OECD Prüfrichtlinie für die Größenbestimmung von Nanomaterialien" mit Vorstellung der beteiligten Fachbereiche. T2 - Expertenaustausch BAM-BMU-BMWi CY - Berlin, Germany DA - 01.06.2018 KW - Nano KW - OECD KW - Nanopartikel KW - Nanomaterial KW - Größenbestimmung PY - 2018 AN - OPUS4-45110 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bresch, Harald A1 - Schmidt, Alexandra T1 - OECD-Prüfrichtlinie zur Größenbestimmung von hergestellten Nanomaterialien N2 - Impulsvortrag für den Beirat des Themenfeldes Umwelt über die in Erstellung befindliche OECD Prüfrichtlinie für die Größenbestimmung von künstlich hergestellten Nanomaterialien. T2 - Sitzung des Beirates des Themenfelds Umwelt 2018 CY - Berlin, Germany DA - 26.02.2018 KW - Nano KW - OECD KW - Prüfrichtlinie KW - Nanopartikel KW - Nanomaterial PY - 2018 AN - OPUS4-45111 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Agency perspectives on geomembrane durability, service life and end of life N2 - Die Präsentation erläutert die Hintergründe der nationalen Anforderungen für die Verwendung von Kunststoffdichtungbahnen in Deponieabdichtungen. Die Beständigkeit wird diskutiert. Anforderungen an das Qualitatsmanagement während der Produktion der Produkte und der Bauphase werden aufgezeigt und die Auswirkungen auf die langzeitige Funktionserfüllung werden beschrieben. T2 - IGS TC-B GeoBarrier Workshop CY - Munich, Germany DA - 06.06.2018 KW - Beständigkeit KW - Kunststoffdichtungsbahnen KW - Deponiebau PY - 2018 AN - OPUS4-45123 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bresch, Harald A1 - Schmidt, Alexandra A1 - Bachmann, V. A1 - Kämpf, K. A1 - Kuhlbusch, T. A1 - Schwirn, K. A1 - Völker, D. T1 - OECD Test Guideline on particle size and size distribution of manufactured nanomaterials N2 - The properties of nanomaterials are influenced not only by their chemical composition but also by physical properties (such as size, geometry and crystal structure). For the reliable determination and assessment of behaviour and effects of nanomaterials as well as for the determination of the exposure of humans and environment a comprehensive physical-chemical characterization of nanomaterials is essential. This is an important prerequisite to identify them as nanomaterials and to interpret and compare test results and - in future – to forecast interaction and effects of nanomaterials. In 2006, the OECD launched a sponsorship program for the testing of nanomaterials in which 11 nanomaterials were thoroughly investigated using a variety of methods. The aim of the project was, among other things, to find out where problems occur and where there are gaps in the measurement and test procedures and where are changes required. An important outcome of the sponsorship program was the finding that the OECD Test Guidelines should in several cases be extended to the specific needs in testing of nanomaterials. The existing standardized test methods of the OECD for physical-chemical characterization have not been developed for nanomaterials in particular. A high demand for an extension of the test guidelines was identified. Germany complied with the OECD's request in 2017 and has agreed to extend the “Test Guideline on Particle Size Distribution / Fiber Length and Diameter Distributions Test Guideline” for Manufactured Nanomaterials (MN). UBA commissioned BAM and BAuA with the preparation of the Test Guideline. The aim of the project is the development of a harmonized test protocol for a valid and reproducible determination of particle size and size distribution which is one of the most relevant physical-chemical properties for MNs. Different measuring methods provide different results for the size distribution of the particles. This is caused by the different measuring principles of the methods. Each method measures a specific parameter that ultimately determines particle size. First, the measured quantity differs for each method (Scattered light intensity, 2D image / projection, electric mobility, etc.). Second, the calculated diameters of the MN may differ (Feret Diameter, Area Projection, Mobility Diameter, Aerodynamic Diameter, Hydrodynamic Diameter). Third, a measuring method provides a size distribution which is measured either mass-based, surface-based or number-based. A conversion between the results requires additional parameters and thus possibly increases the measurement error. In addition to the technical differences, the individual parameters are strongly influenced by the structure and material of the nanoparticles. For example, a surface functionalization can lead to very different results in the size distribution. The suitability of measurement methods differs with the material of the MN. As a result, two very different results can be measured for the particle size distribution using two different methods, which are nevertheless both correct. Several large projects in recent years therefore concluded that nanomaterials should be characterized by at least two complementary method. Imaging techniques are regarded as one of these methods for the characterization, the complementary methods are supposed to be statistical methods. The different results for the size distribution of nanomaterials become problematic for the registration of new MN. A comparable and reproducible size distribution is a prerequisite for a standardized registration. In the future, the particle size distribution in the EU will also decide on the classification of a substance as a nanomaterial or as a non-nanomaterial. Especially in borderline cases, a standardized and comparable measurement methodology is therefore essential. T2 - BAM-PTB Workshop 2018 CY - Berlin, Germany DA - 14.05.2018 KW - Nano KW - OECD KW - Test Guideline KW - Size distribution KW - Particle PY - 2018 AN - OPUS4-45106 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schmidt, Selina A1 - Schreiber, Frank T1 - Antimicrobial resistance in soil microbes mediated by resistance evolution and horizontal gene transfer (HGT) N2 - Biocides are in contact with soils through direct application and passive leaching from protected materials. Consequently, soil microorganisms are exposed to biocides even though they are not their primary targets. Soil is a large reservoir of microbial diversity and has been hypothesized to be a crucial factor for the evolution and spread of antimicrobial resistance. Currently, there is little knowledge on how biocides used to protect materials affect the evolution and spread of resistance. Thus, our aim is to investigate the risk for the evolution of biocide resistance and cross-resistance to antibiotics. In addition, we aim to elucidate the affect of biocides on the spread of resistance via horizontal gene transfer (HGT). In adaptive laboratory evolution experiments we cultured selected model soil microorganism with representative biocides under selection regimes with increasing and stable biocide concentrations followed by antibiotic and biocide cross-resistance determination. Moreover, we investigate if the selected biocides affect the rates of de novo mutations and HGT of plasmids that carry resistance genes among soil microorganism. Our results show only small increases of biocide resistance during serial transfers under increasing biocide concentrations. One reason for this might be the narrow selective window for biocide resistance due to steep dose-response relationships. Furthermore, our results indicate that a stable low-level biocide regime did not select for high level cross-resistance to antibiotics and other biocides. Moreover, material preservatives affected the rates of HGT via conjugation and the mutation rates at sub-inhibitory concentrations. The results will enable future risk assessment regarding resistance evolution for biocides used as material preservatives. T2 - 4th Evo Eco PhD Meeting CY - Lutherstadt Wittenberg DA - 04.03.2020 KW - Microbiology KW - Biocides KW - Horizontal gene transfer HGT KW - Resistance evolution KW - Antimicrobial resistance PY - 2020 AN - OPUS4-51313 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, Julia T1 - How light determines the life of the plant pathogen Botrytis cinerea N2 - The rotation of the Earth causes a day/night cycle that is characterized by changing light and temperature conditions. Fungi actively sense the environmental light conditions to induce protective mechanisms against the light-associated stresses and to regulate development. Since fungi adapted to habitats with different light regimes, the complexities of their ‘visual’ systems and photoresponses may vary significantly. Fungi that are associated with plants experience a special light regime because the host seeks optimum light conditions for photosynthesis – and the fungus must cope with them. Moreover, fungi living under the canopy are confronted with an altered spectrum enriched for green and far-red light. Plants sense light to coordinate growth and morphogenesis: a low red:far-red ratio indicates the presence of competitors (shading by other plants) and triggers the shade avoidance response which is accompanied by increased susceptibility to nectrophic pathogens. Botrytis cinerea, the causal agent of gray mold diseases on many plant species in moderate climate zones (high humidity, temperatures around 20°C, seasons), exhibits striking photoresponses accompanied by a broad action spectrum and a high number of photoreceptors. Light is the most important factor controlling morphogenesis: it induces conidiation for disease spreading (summer cycle) and represses sclerotial development for survival and/or sexual recombination (winter cycle). In the past years, we identified several cellular components involved in photoperception and regulation of photomorphogenesis and virulence indicating that the same signaling pathways are of relevance for both processes, propagation and infection. Notably, we recognized the role of the phytochromes (red/far-red light sensors) for coordinated responses to light and elevated temperatures (photo-/thermomorphogenesis) – similar to the function of Arabidopsis PhyB. BcPHY2-like thermosensors are likely restricted to the Leotiomycetes, which include several plant pathogens of the moderate climate zones. T2 - Fungal Genetics Conference 2019 CY - Asilomar, CA, USA DA - 12.03.2019 KW - fungus KW - light KW - plant pathogen KW - signaling KW - virulence PY - 2019 AN - OPUS4-48128 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, Julia T1 - Photoperception in black fungi that share niches with green organisms N2 - Sunlight, the major source of energy, drives life but in excess it provokes UV-induced DNA damage, accumulation of reactive oxygen species, desiccation, osmotic stresses and so on. Biological strategies to survive excess light include protection, avoidance and active utilisation. Phototrophic organisms including cyanobacteria, green algae and plants use all three strategies. Fungi occupying phototrophic niches may profit from the surplus photosynthetic products which also obliges them to cope with the same light-induced stresses. One way of handling these stresses would be to use similar signalling pathways to sense the presence and to interact with their phototrophic partners. Obviously, the levels of adaptation and responses to light will depend on the environment as well as fungal genotype and phylogenetic position. Black fungi – a polyphyletic group – accumulate the dark pigment DHN melanin in their cell walls and often occupy light-flooded habitats from phyllosphere to rock surfaces. Here we compare two sequenced melanised fungi of different lifestyles in their response to light. The Leotiomycete Botrytis cinerea is an aggressive pathogen that primarily infects the above-ground parts of plants. It possesses large numbers of photoreceptors that respond to a broad spectrum of light. As a consequence, light controls morphogenesis in which it induces conidiation for disease spreading and represses sclerotial development for survival and/or sexual recombination. Cellular components involved in photo-perception and regulation of morphogenesis, stress responses and virulence have been identified and appear to regulate propagation, survival and infection. These include phytochromes, a group of photoreceptors which are particularly enriched in the Leotiomycetes and that mediate coordinated responses to light and elevated temperatures. Assuming that photo-regulation may be equally important for fungi that live in mutualistic relationships with phototrophs either by forming composite organisms or biofilms, we investigate the role of light in the rock-inhabiting Eurotiomycete Knufia petricola. Like other black yeasts, K. petricola grows slowly, does not form specialised reproductive structures and constitutively produces DHN melanin as well as carotenoids. Combining K. petricola with the cyanobacterium Nostoc punctiforme, we developed a model system for studying biofilm formation and bio-weathering. A genetic toolbox to manipulate this model system is being developed. K. petricola strain A95 possesses ten putative photoreceptors, more than found in filamentous Eurotiomycetes suggesting that light plays an important role for abiotic and biotic interactions in extremo-tolerant and symbiosis-capable fungi. T2 - International Symposium on Fungal Stress (ISFUS) CY - Sao Jose dos Campos, Brazil DA - 19.05.2019 KW - Botrytis KW - carotenoids KW - Knufia KW - melanin KW - Nostoc PY - 2019 AN - OPUS4-48130 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Koerdt, Andrea A1 - An, Biwen Annie A1 - Kleinbub, Sherin T1 - Investigation of methanogen-induced microbiologically influenced corrosion (Mi-MIC) using simulated marine environments under flowing conditions N2 - Microbially influenced corrosion (MIC) of iron is usually attributed to sulfate-reducing microorganisms (SRM) which act upon the metal by the reactiveness of hydrogen sulfide, and by withdrawal of the available electrons in electrical contact with the metal. Methanogenic archaea can also cause MIC by directly withdrawing electrons from the iron surface for methanogenesis. However, the mechanistic details and kinetics of the overall process are poorly understood. Precipitation of siderite, a by-product of methanogenesis, (4Fe + 5HCO3 + 5H+  4FeCO3 + CH4 + 3H2O) can lead to an insulating layer on the metal surface and lower the corrosion rate. Still, the extent of FeCO3 precipitation may be significantly influenced by environmental conditions such as pH and advective processes. T2 - Dechema CY - Frankfurt a. M., Germany DA - 13.05.2019 KW - MIC KW - Corrosion KW - Methanogens KW - Corrosion product PY - 2019 AN - OPUS4-47982 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogl, Jochen T1 - What isotopes can do... N2 - The talk gives Brief overview on the effects causing isotope variations in nature and some typical applications. It also Points to a potential application in corrosin sciences. T2 - Final Colloquium: Microbiologically influenced corrosion CY - Berlin, Germany DA - 21.05.2019 KW - Iron isotope fractionation KW - Microbially induced corrosion PY - 2019 AN - OPUS4-48273 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Braun, Ulrike A1 - Eisentraut, Paul T1 - Mikroplastik als analytische Herausforderung N2 - Der Vortrag beschäftigt sich mit den gängisten Methoden zur Probennahme, -vorbereitung und Detektion von Mikroplastik. Das Zusammenspiel von Fragestellung und Methode wird betont. Es wird auf das Dikussionspapier Analytik des BMBF-Forschungsschwerpunktes Plastik in der Umwelt besonders hingewiesen sowie Bemühungen zur Normierung der Methoden auf deutscher und internationaler Ebene dargestellt. T2 - 18. BfR-Forum Verbraucherschutz: Mikroplastik CY - Berlin, Germany DA - 06.06.2019 KW - Mikroplastik KW - Analyse KW - Normung PY - 2019 AN - OPUS4-48234 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Erning, Johann Wilhelm A1 - Bobzien, M. T1 - Corrosion behaviour of printed 1.4404 in drinking water systems N2 - The regulations for materials in contact with drinking water require tests to evaluate the hygienic properties of the materials. A printed 1.4404 was tested according to EN 16056 and the suitability for the use in drinking water was proven. T2 - Eurocorr 2020 CY - Online meeting DA - 07.09.2020 KW - Passivity KW - Drinking water KW - Stainless steel KW - Additive manufacturing PY - 2020 AN - OPUS4-51237 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gorbushina, Anna T1 - Life on the rocks and other hard surfaces N2 - After their discovery on rock surfaces in cold and hot deserts, a polyphyletic group of ascomycetous black fungi was found to dominate a range of hostile environments – natural and man-made, from salterns to dishwashers, roofs and solar panels. Together with bacteria and algae they may establish subaerial biofilms and cause weathering of the surfaces they grow on. Their impressive survival abilities as well as their constitutive protective pigmentation and cluster-like microcolony organisation are similar in environmental isolates as well as in heat-tolerant opportunistic pathogens of animals and humans. We selected the rock-inhabiting fungus Knufia petricola (class Eurotiomycetes, order Chaetothyriales) that exhibits all the characteristics of microcolonial black fungi such as yeast-like cell growth, absence of reproductive structures and constitutive dihydroxynaphthalene (DHN) melanogenesis (Nai et al. 2013, Fungal Genet Biol). We developed protocols to efficiently generate and transform protoplasts resulting in stable homokaryotic transformants by targeting genes involved in pigment synthesis. The differences between the wild-type fungus and its melanin-deficient mutants were tested in geomicrobiological experiments and measured are now discussed in detail, with special accent on the possible effects of the mutation on EPS and other exuded substances. T2 - Departmental colloquium of the Tuscia University CY - Viterbo, Italy DA - 14.02.2020 KW - Ascomycetes KW - Fungal biofilms KW - Material surface colonisation KW - Genetics KW - Genomics KW - Extremophilic fungi PY - 2020 AN - OPUS4-50643 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, Julia T1 - Many-sided DHN melanin – spotlight on its function in microcolonial black fungi N2 - Dihydroxynaphthalene (DHN) melanin is produced by different Ascomycetes via slightly differing biosynthetic routes. The polyketide synthases (PKS) release the heptaketide YWA1, the hexaketide AT4HN or the pentaketide T4HN. The first two products are deacetylated by ‘yellowish-green’ hydrolases to T4HN, and T4HN is further converted by a core set of enzymes to DHN. Final polymerization steps are accomplished by multicopper oxidases. DHN melanogenesis is often regulated in a spatial and temporal fashion resulting e.g. in melanized reproduction, survival and/or infection structures. Remarkable is the regulation of the DHN melanogenesis in the foliar plant pathogen Botrytis cinerea: it involves two differently expressed PKSs providing the precursor in conidia and sclerotia, respectively (Schumacher 2016, Mol Microbiol). In contrast, a polyphyletic group of Ascomycetes (microcolonial fungi/ black yeast) dwelling in hostile habitats such as bare rock surfaces in hot and cold deserts, exhibits constitutive melanogenesis. Here, DHN melanin builds a protective layer around all vegetative cells thus contributing to the survival of diverse environmental stresses even without specialized reproduction structures. As part of our continuing research on microcolonial rock-inhabiting fungi, we chose the genetically amenable Knufia petricola strain A95 (Nai et al. 2013, Fungal Genet Biol; Noack-Schönmann et al. 2014, AMB Express) for detailed studies. DHN-deficient mutants generated by targeted mutation of biosynthetic genes were studied with regard to the architecture of the cell wall and the EPS (extracellular polymeric substances) matrix, attachment to and weathering of olivine, as well as the tolerance to abiotic and biotic stresses. We will discuss the critical role of the outer cell surface (DHN melanin and EPS) in adhesion to the substrate and subsequent damage of the colonized surface. T2 - European Conference on Fungal Genetics (ECFG15) CY - Rome, Italy DA - 17.02.2020 KW - fungus KW - melanin KW - pigmentation PY - 2020 AN - OPUS4-50591 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schumacher, Julia T1 - Genetic manipulation of the microcolonial black fungus Knufia petricola N2 - Microcolonial black fungi, a polyphyletic group of ascomycetes, exhibit constitutive melanin formation, yeast-like growth and high stress tolerances. They dominate – often together with bacteria and algae in sub-aerial biofilms – a range of hostile environments including natural and man-made ones, from salterns to dishwashers, roofs and solar panels. Because of lacking genetic tools and the slow growth of most isolates, the genetic bases for these specific properties are largely unknown. The rock-inhabiting fungus Knufia petricola (Eurotiomycetes, Chaetothyriales) exhibits all characteristics of microcolonial black fungi and was selected as recipient for genetic engineering to study gene functions and genetic interactions. Different variants of green and red fluorescent proteins were successfully expressed indicating that fluorescence microscopy using genetically encoded fluorescent proteins and fluorescent dyes enables various cell biology approaches. Furthermore, genes of biosynthetic pathways (DHN melanin, carotenoids, uracil, adenine) were successfully mutated by applying traditional gene replacement and plasmid-based or ribonucleoprotein (RNP)-based CRISPR/Cas9 or silenced by RNA interference (RNAi). The availability of this advanced and efficient genetic toolbox and the annotated genome sequence of strain A95 makes K. petricola an excellent model for exploring the secrets of microcolonial black fungi. T2 - Departmental colloquium of the Tuscia University CY - Viterbo, Italy DA - 14.02.2020 KW - black fungus KW - genetics KW - Crispr/Cas9 PY - 2020 AN - OPUS4-50592 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Jann, Oliver T1 - Stand der Technik der Emissionsmessungen für das Umweltkompartiment Luft N2 - Der mitteleuropäische Mensch hält sich 80 – 90 % der Zeit in Innenräumen auf. Je nach Aktivität atmet er 10 – 20 m³ bzw. 12 - 24 kg Luft täglich, das ist weit mehr als das Doppelte der Summe an Essen und Trinken. Die technischen Voraussetzungen für die Bestimmung von Emissionen aus Bauprodukten in die Luft liegen vor – harmonisierte horizontale Prüfnorm EN 16516. Es dürften mittlerweile zig-tausende Emissionsdatensätze vorliegen. Defizite gibt es bei der Kennzeichnung zur Unterscheidung emissionsarmer und emissionsreicher Produkte, die bestehende CE-Kennzeichnung ist unvollständig, ersatzweise gibt es nationale Regelungen. Gerade bei modernen, dichten Bauten mit geringem natürlichen Luftwechsel sind hohe Schadstoffkonzentrationen zu erwarten, wenn nicht emissionsarme Materialien und Produkte zum Einsatz kommen. T2 - Eurolab-Workshop Anforderungen an Bauprodukte - Umweltrelevante Aspekte sowie die gesamtheitliche Bewertung CY - Berlin, Germany DA - 11.11.2019 KW - Gesundheit KW - Emissionsmessungen KW - Bauprodukte KW - Luft KW - Bauproduktenverordnung PY - 2019 AN - OPUS4-49596 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Gorbushina, Anna T1 - Microbiology / biofilms in material research and testing N2 - In the modern world there is an increased understanding that design and performance monitoring of materials have to be tested in connection to chemical, physical and (micro)biological challenges. A systematic study on how biofilms interact with materials and what could be done to engineer biofilms and/or materials in order to maximize the resistance of the material (surface) or the resistance the biofilm-modified material (bulk) is in strong need. In the Department “Materials and the Environment” of the BAM new experimental platform is being developed. With the help of different type of device for high throughput and microbiologically-controlled environment simulation we establish a new approach to clarify the mechanisms of biofilm/material interactions. Despite the focus on fundamental research, the main results of this project proposal will be transferable into material technology and construction chemistry and will influence the development of standardization in this topic. As the interactions of biofilms and materials have implications for most constructions as well as climate change, the results of the research generates additional value. T2 - Initialgespräch - DFG-Forschungsgruppe "Mikrobiologie/Biofilme" CY - Karlsruhe, Germany DA - 14.11.2019 KW - Biofilm KW - Microbiology KW - Black fungi KW - Solar panel PY - 2019 AN - OPUS4-50199 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -