TY - JOUR A1 - Radunz, Sebastian A1 - Kraus, Werner A1 - Bischoff, F. A. A1 - Emmerling, Franziska A1 - Resch-Genger, Ute A1 - Tschiche, Harald T1 - Temperature- and Structure-Dependent Optical Properties and Photophysics of BODIPY Dyes N2 - We report on the temperature- and structural-dependent optical properties and photophysics of a set of boron dipyrromethene (BODIPY) dyes with different substitution patterns of their meso-aryl subunit. Single-crystal Xray diffraction analysis of the compounds enabled a classification of the dyes into a sterically hindered and a unhindered group. The steric hindrance refers to a blocked rotational motion of the aryl subunit around the bond connecting this moiety to the meso-position of the BODIPY core. The energy barriers related to this rotation were simulated by DFT calculations. As follows from the relatively low rotational barrier calculated to about 17 kcal/mol, a free rotation is only possible for sterically unhindered compounds. Rotational barriers of more than 40 kcal/mol determined for the sterically hindered compounds suggest an effective freezing of the rotational motion in These molecules. With the aid of temperature-dependent spectroscopic measurements, we could show that the ability to rotate directly affects the optical properties of our set of BODIPY dyes. This accounts for the strong temperature dependence of the fluorescence of the sterically unhindered compounds which show a drastic decrease in fluorescence quantum yield and a significant shortening in fluorescence lifetime upon heating. The optical properties of the sterically hindered compounds, however, are barely affected by temperature. Our results suggest a nonradiative deactivation of the first excited singlet state of the sterically unhindered compounds caused by a conical intersection of the potential energy surfaces of the Ground and first excited state which is accessible by rotation of the meso-subunit. This is in good agreement with previously reported deactivation mechanisms. In addition, our results suggest the presence of a second nonradiative depopulation pathway of the first excited singlet state which is particularly relevant for the sterically hindered compounds. KW - Fluorescence KW - Sensor KW - Switch KW - pH KW - BODIPY KW - Dye KW - Probe KW - Synthesis KW - Photophysics KW - Mechanism PY - 2020 DO - https://doi.org/10.1021/acs.jpca.9b11859 SN - 1089-5639 VL - 124 IS - 9 SP - 1787 EP - 1797 PB - American Chemical Society AN - OPUS4-50639 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kittner, Maria T1 - Bewertung der Freisetzung von Mikroplastik aus Sportböden auf Kunststoffbasis N2 - Es handelt sich hierbei um die Abschluss-Präsentation des Projektes "Bewertung der Freisetzung von Mikroplastik aus Sportböden auf Kunststoffbasis", die am 28.11.24 vor dem Drittmittelgeber Zukunft Bau Forschungsförderung im Rahmen der 28. Projekttage der Bauforschung präsentiert wurde. Der 30-minütige Vortrag gliederte sich in die Kapitel Forschungsbedarf, Konzept, Ergebnisse und Take Home-Messages des Projektes. T2 - 28. Projekttage der Zukunft Bau Forschungsförderung CY - Online meeting DA - 26.11.2024 KW - Mikroplastik KW - TED-GC/MS KW - Kunststoffrasen KW - PAK KW - Schwermetalle KW - Mikroplastik Eluat Lysimeter PY - 2024 AN - OPUS4-61815 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Tuma, Dirk A1 - Mady, A. H. A1 - Baynosa, M. L. A1 - Saad, M. A1 - Dhakal, G. A1 - Kim, W. K. A1 - Shim, Jae-Jin T1 - Morphology-engineered hollow NiTiO₃/C–Ag/Ag₃PO₄ S-scheme heterojunction photocatalyst: mechanistic insights into sunlight-driven tetracycline degradation N2 - Tetracycline (TCH), a widely used antibiotic, persists in aquatic and terrestrial environments, posing ecological risks and accelerating antibiotic resistance. To address this, we report a hollow-structured NiTiO₃/C–Ag/Ag₃PO₄ (NT/C–AAP) photocatalyst—the first hollow-type nickel titanate—synthesized via a self-template solvothermal route followed by photodeposition. The catalyst integrates key design strategies—hollow architecture, oxygen vacancies, carbon coating, and an S-scheme heterojunction—to optimize photocatalytic performance. The hollow structure enhances light harvesting via internal scattering, oxygen vacancies facilitate O2 adsorption and superoxide (O₂•⁻) generation, and the S-scheme heterojunction effectively suppresses electron–hole recombination while preserving strong redox potential. NT/C–AAP achieved 96% TCH degradation within 1 h and 82% mineralization in 3 h under solar light, far exceeding core–shell (18%) and aggregated (47%) NiTiO₃-based catalysts. Complete removal was realized within 40 min under 400 W visible light. The catalyst maintained 96% activity after five cycles, confirming excellent durability. Compared with previously reported NiTiO₃ photocatalysts, NT/C–AAP delivered a 50–400% performance enhancement arising from its engineered hollow structure and improved electronic properties. Mechanistic studies identified O₂•⁻ and •OH radicals as dominant species, validating the role of morphology and interface engineering in directing charge separation and redox activity. Additionally, a catalyst performance index was proposed to facilitate comparison across diverse conditions. Overall, this work introduces a novel, durable photocatalyst that links structural design to functional performance and demonstrates strong potential for practical environmental remediation. KW - Heterojunction photocatalyst KW - Photodegradation KW - Tetracycline PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-655946 DO - https://doi.org/10.1007/s42114-025-01600-x SN - 2522-0128 VL - 9 IS - 2 SP - 1 EP - 19 PB - Springer Nature CY - London AN - OPUS4-65594 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schwibbert, Karin A1 - de Eulate Pérez, Elisa García A1 - Wen, Keqing A1 - Voss, Heike A1 - Thiele, Dorothea A1 - Richter, Anja M. A1 - Bonse, Jörn T1 - Escherichia coli repellence via laser-induced periodic surface structures (LIPSS) on titanium: Critical role of biofilm-associated gene expression N2 - The inconsistency in the observed bacteria-repellent effects of laser-induced surface textures remains a subject of scientific debates. With E. coli TG1 as test strain, we performed biofilm formation assays on ultrashort pulse laser textured titanium. Samples covered with low spatial frequency LIPSS (LSFL) of periods around 750 nm or with high spatial frequency LIPSS (HSFL) featuring smaller periods around 100 nm were processed on polished samples. While LSFL significantly reduce the number of adhering bacteria compared to the polished reference, HSFL do not. Simultaneously, we concentrate our study on bacterial strategies employed for biofilm formation, that is the transcription of the biofilm-associated genes csgB, involved in primary adhesion to a surface, and wza, participating in biofilm maturation. Promoter regions of these genes were cloned into a promotor probe plasmid with the green fluorescent protein GFP+ as reporter and transferred into the test strain. As indicated by the fluorescence intensity of the reporter protein, among the bacteria colonizing LSFL-covered areas, a markedly higher proportion of cells transcribing csgB or wza were detected, compared to the bacterial populations colonizing the polished or HSFL-covered areas. To our knowledge, this is the first study indicating that the antifouling effect of LSFL topographies can be counteracted when bacteria activate biofilm-associated genes. KW - Laser-induced periodic surface structures (LIPSS) KW - Titanium KW - Biofilm KW - Antifouling KW - Gene expression KW - Fluorescence microscopy PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-655572 DO - https://doi.org/10.1016/j.apsusc.2026.166363 SN - 0169-4332 VL - 730 SP - 1 EP - 9 PB - Elsevier B.V. AN - OPUS4-65557 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Božičević, Lucija A1 - Altmann, Korinna A1 - Hildebrandt, Jana A1 - Knigge, Xenia A1 - Vrček, Valerije A1 - Peranić, Nikolina A1 - Kalcec, Nikolina A1 - Vinkovic Vrcek, Ivana T1 - Estrogenic activity of plastic nanoparticles mixture under in vitro settings N2 - The plastic value chain, central part of modern living, caused environmental pollution and bioaccumulation of plastic nanoparticles (PNPs). Their ubiquitous presence in different environmental and biological compartments has become a serious threat to human health and ecosystems. Frequently used plastic materials such as polypropylene (PP), polystyrene (PS) and polyethylene (PE) have been detected in the form of PNPs in the food chain, soil, water and air, as well as in human feces and blood. In this study, we aimed to provide novel insights in endocrine disrupting properties of PNPs using in vitro estrogen receptor (ER) transactivation assay. The effects of PP-NPs, PE-NPs and PS-NPs and their mixture on T47D-KBluc cell line stably transfected with luciferase as reporter enzyme was evaluated by means of cytotoxicity, cellular uptake and ER activation. Tested dose range for PNPs was 0.001 – 10 mg/L. Both cellular uptake and cytotoxicity for all PNPs was found to be dose-dependent. Only the highest dose of PP-NPs and PE-NPs induced apoptosis and cell death, while PS-NPs were not cytotoxic in tested dose range. For tested concentrations, PP-NPs and PE-NPs showed significant agonistic activity on ER, while PS-NPs cannot be considered ER active. When, applied as mixture, PNP demonstrated additive toxicity effects compared to the effect of each individual PNPs. Additivity was also observed for ER agonistic effect of PNPs mixture according to the benchmark dose-addition modelling approach. This study provides missing science-based evidence on endocrine disrupting effects of PE-NPs, PP-NPs, PS-NPs and their mixtures and highlights the importance of considering unintentional, aggregate and combined exposure to different PNPs in risk management. KW - Risk assessment KW - Nanoplastics KW - Estrogenic activity of plastic nanoparticles PY - 2024 DO - https://doi.org/10.1039/D3EN00883E SN - 2051-8153 VL - 11 IS - 5 SP - 2112 EP - 2126 PB - Royal Society of Chemistry (RSC) AN - OPUS4-59724 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Schmitt, M. A1 - Altmann, Korinna A1 - Fengler, Petra A1 - Gehde, M. T1 - Air-based polyethylene fragmentation with high yield to form microplastic particles as reference material candidates N2 - Microplastic particles with sizes between 1 to 1000 μm are widely distributed worldwide. Origin, transport pathways and fate are poorly known, as sampling, sample preparation and detection methods are major challenges. In addition, reference materials that mimic environmental particles are lacking. Most challenging is the yield of MP particle production and the need for resource-intensive grinding with liquid nitrogen. In this paper, a machine is designed to produce aged microplastic particles as reference material candidates with high yield. The machine is based on ultraviolet aging of a thin foil and mechanical fragmentation using clean air. An example of aging and fragmentation of high density polyethylene with additional physical and chemical characterization of shape, size, aging state by carbonyl index and density is presented. KW - Microplastics KW - Degradation of polyethylene KW - Air fragmentation KW - Microplastics reference material PY - 2023 DO - https://doi.org/10.1002/appl.202200121 SP - 1 EP - 18 PB - Wiley online library AN - OPUS4-57203 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Weber, Simone T1 - Influence of the pH Value to the Degradation of Ester-Based Thermoplastic Polyurethanes N2 - Microplastics are solid polymeric particles with a size of 1-1000 μm (ISO/TR21960:2020), which can be emitted from mismanaged waste into the environment, where microplastic is now ubiquitous. What happens to the microplastics after ending up in the environment, which risks entail and what effects it has are not sufficiently clarified up to now. The most certain issue is that the plastic particles in the environment are exposed to natural ageing, are fragmenting and degrading, such that the potential risk to ecosystems and humans is increasing due to the formation of smaller and smaller particles, potentially even including nanoplastics, if these are ingested before their further degradation. Therefore, and in view of a possible registration of polymers under REACH in the future, it is necessary to investigate the degradation of thermoplastic polyurethanes (TPU) regarding hydrolysis stability to evaluate possible risks and effects to the environment. In the present studies, one thermoplastic polyurethane – with and without hydrolysis stabilizer – is exposed to different pH buffers at 50°C for 14 days to investigate hydrolysis depending to different pH values (acid, alkali and neutral) based on OECD guideline TG111. The hydrolysis behavior of the TPUs is characterized by surface sensitive techniques and on bulk properties. First degradation effects can be detected by SEC. Hydrolysis, especially under acidic and basic conditions, leads to chain scissions to lower molecular masses. Furthermore, the degradation products which indicate the structure of the bulk material were detected by thermo-analytical methods like TGA-FTIR for the small degradation products and the thermo extraction/desorption-gaschromatography/mass spectrometry (TED-GC/MS) for bigger degradation products. Acidic and basic hydrolysis shows the same degradation behavior which is caused by a preferred scission of the ester and urethane functionalities. Surface-sensitive techniques such as XPS demonstrate less carboxylic acid formation at acidic than at alkaline pH value in the TPU without stabilator, where as the TPU with stabilator ages to the same extent in both pH ranges. Altogether, the hydrolysis of TPUs – independently of added stabilizer or not – in acid and alkali environment is accelerated compared to the neutral hydrolysis. T2 - SETAC CY - Dubin, Ireland DA - 30.04.2023 KW - Degradation KW - Thermoplastic Polyurethane KW - Microplastic KW - Polymer Hydrolysis KW - Polymer 3R KW - REACH PY - 2023 AN - OPUS4-58906 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Cirkovic Velickovic, T. A1 - Altmann, Korinna A1 - Dailey, L T1 - CUSP Conference WG1 & WG3: MATERIALS AND METHODS N2 - This talk is a presentation about the main results of the CUSP cluster on micro- and nanoplastics human health that work from 2021 to 2025 in Horizon Europe programme according to the WG1 and 3. These groups combined the analytics and the materials with interlaboratory comparisons (ILC). The talk reflects the need of realistic test materials with defined properties for micro- and nanoplastic research. Some were developed are now available. The talk also highlights the need for harmonisation and the results of different ILCs that were performed. T2 - CUSP conference CY - Brussels, Belgium DA - 25.02.2025 KW - Microplastics KW - Reference materials KW - Interlaboratory comparison (ILC) PY - 2025 AN - OPUS4-62703 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kittner, Maria A1 - Kalbe, Ute A1 - Altmann, Korinna T1 - Freisetzung von Mikroplastik aus Sportböden N2 - Die Europäische Kommission hat 2023 ein Verbot zum bewussten Austrag von Mikroplastik (MP) in die Umwelt beschlossen, das auch für die Verwendung von synthetischen Gummi-Granulaten (v. a. EPDM) in Sportböden gilt. In Deutschland gibt es laut DFB ca. 5100 Kunstrasenplätze. In der EU beläuft sich die Anzahl laut ECHA auf 13,000 Kunstrasen- und 47,000 Bolzplätze, Tendenz steigend. Das Hauptziel des Projektes ist daher, eine Massenbilanz für die Freisetzung von MP zu erstellen, um so eine Schätzung des MP-Austrags pro Kunstrasenplatz und Jahr zu ermöglichen. Dafür werden die MP-Emissionen von drei Kunstrasenszenarien in verschiedenen Zuständen (ungealtert, künstlich gealtert und in Echtzeit gealtert) verglichen: die Vergangenheit (Kunstrasen: fossilbasiert, EPDM-Füllung), die Gegenwart (der in Europa am häufigsten installierte Rasen) und die Zukunft (Rasen mit recycelten Grasfasern, keine synthetische Füllung sondern z.B. Quarzsand oder Korkschrott). Dazu werden fabrikneue Kunststoffrasen und EPDM-Granulat unter Laborbedingungen beschleunigt gealtert, um die Freiland-Beanspruchung eines Kunststoffrasens in circa 15 Jahren abzubilden. Die Verwendung spezieller Mikrofiltertiegel in Lysimeter-Experimenten ermöglicht die Abschätzung der Partikelgrößen des emittierten MP, was eine Grundbedingung für die Bewertung einer potenziellen Gesundheitsgefährdung für Menschen ist. Ergänzend werden weitere umweltrelevante Schadstoffausträge aus den Kunststoffrasen quantifiziert und so mögliche Transportpfade überprüft. Um in Zukunft den Anforderungen des Kreislaufwirtschaftsgesetzes zu entsprechen, sollen in diesem Projekt zudem Erkenntnisse zur Rückführbarkeit von Gummi-Granulaten und Altrasen in den Rohstoffkreislauf gewonnen werden KW - Mikroplastik KW - TED-GC/MS KW - Kunststoffrasen KW - PAK KW - Schwermetalle PY - 2024 UR - https://www.zukunftbau.de/neue-meldung/zukunft-bau-journal-2024 SP - 9 EP - 9 PB - Bundesinstitut für Bau-, Stadt- und Raumforschung (BBSR) CY - Bonn AN - OPUS4-61823 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Frelih, Milena T1 - Impact of Engineered Nanomaterials on Microbial Communities in the Aquatic Environment N2 - Engineered nanoparticles have garnered significant attention for their unique properties and potential applications across various industries. They were extensively examined for their toxicological effect in vitro and in vivo, but their effects on environmental and biological systems remain underexplored. A key area of concern is how nanoparticles interact with microbial communities in natural ecosystems, since these communities are vital for processes such as nutrient cycling, biodegradation, and maintaining ecosystem health and functioning. Currently, environmental risk assessments of nanoparticles majorly involve higher organisms (e.g. algae, zooplankton), but omit the effects on complex communities and ecosystems as a whole. This research aims to investigate the impact of nanomaterials on aquatic microbial communities using a combination of laboratory experiments and field-sampling along a gradient from low to highly anthropogenically impacted aquatic ecosystems around Berlin, Germany. To holistically assess changes in microbial composition and functional activity in response to nanomaterial exposure, we will apply molecular, microbiological, analytical as well as OMIC methods. We hypothesize that nanoparticles induce significant compositional changes in microbial community structures, potentially leading to alterations in stress responses and other functional effects. Nanomaterials have the potential to benefit the environment by contributing to energy and resource efficiency, remediation of contaminated sites, or water treatment. In order to represent truly sustainable products, though, a safe use for humans and ecosystems must be assured. Ultimately, this research will contribute to more accurate environmental risk assessments and help guide the responsible use of nanotechnology in various industries. T2 - SETAC Europe CY - Vienna, Austria DA - 11.05.2025 KW - Microbial Communities KW - Aquatic Environment KW - Nanomaterials PY - 2025 AN - OPUS4-63164 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Detektion von Mikroplastik N2 - In dem Vortrag geht es um die Möglichkeiten der Detektion von Mikroplastik im Allgemeinen. Es werden Beispiele für die Luft gezeigt. T2 - VDI-Workshop „Mikroplastik in der Außenluft – Was wir wissen und was wir (noch) nicht wissen CY - Online meeting DA - 15.11.2022 KW - Mikroplastik KW - Mikroplastik in Luft KW - Detektion von Mikroplastik PY - 2022 AN - OPUS4-56289 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Braun, U. T1 - Thermoanalytical methods to measure mass in microplastics N2 - The talk adresses the use of thermoanalytical methods in microplastics analysis. T2 - EUROLAB webinar: MICROPLASTICS: regulations, standards and the role of laboratories CY - Online meeting DA - 15.02.2023 KW - TED-GC/MS KW - Thermoanalytical methods KW - Microplastic mass PY - 2023 AN - OPUS4-57009 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Release of synthetic fibres during washing of typical household textiles: Findings from washing machine tests and resulting policy recommendations N2 - This talk summarizes the experimental setup and the results of one washing experiment under realistic conditions according to microplastic fiber release. T2 - Tackling microplastics in the environment CY - Brussels, Belgium DA - 09.03.2023 KW - Microplastics KW - Fibers of textile origin KW - Washing machine KW - Microplastic fibre release PY - 2023 AN - OPUS4-57204 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wiesner, Yosri T1 - Metrological Observation of the Stability Performance of Reference Materials for Microplastic Analysis N2 - The formation of microplastic (MP) particles (1-1000 µm) is mostly related to physicochemical degradation processes of macroplastics. Photooxidative damage is often set as the initial degradation process, which leads to embrittlement of the plastics. Mechanical processes then lead to further fragmentation and the formation of MP particles. In the environment, this can be associated with UV exposure through direct radiation from the sun, which leads to radical formation in the polymer systems on the one hand and radical formation of oxygen on the other. The result is material embrittlement usually caused by chain shortening in the polymeric system. Due to specific ecosystem conditions, the damaged polymer is fragmented by erosive, abrasive processes or wave action. According to reference material topic for MP analysis, pristine and artificially weathered polymers are needed. Starting from granulate or macroplastics, these can be pulverised with different techniques, bottled and stored until usage. The bottled powders need to be homogen and stable over a defined time interval regarding to a specific property. This work deals with different polymer types, aged and non-aged. It tries to answer the question under which storage conditions polymers will be stable in particle size. The powders are characterized for chemical composition and shape with FTIR, DSC and SEM. Particle size distribution was measured by laser diffraction with wet and dry dispersion. Artificially pre-aged materials seem to be more vulnerable for further aging and less stable in particle size distribution measurements. T2 - SETAC Dublin– SETAC Europe 33nd Annual Meeting CY - Dublin, Ireland DA - 30.04.2023 KW - Reference material KW - Microplastics KW - Metrological Observation PY - 2023 AN - OPUS4-57475 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lukas, M. T1 - Artificial Plastic Ageing as a Framework for Microplastics Ecotoxicity Evaluation N2 - Microplastics are widely distributed in aquatic and terrestrial environments, up to now less is known on toxicological impacts under realistic conditions. Research so far has focused mainly on the impacts on organisms by fresh plastic fragments or beats. However, plastic materials found in the environment are mainly a mixture of different polymers and particularly degraded during aging processes. Although especially oxidized degradation products might escape from plastic materials during aging, there is a lack of information on potentially adverse effects on aquatic biota. The latter is of particular interest as oxidized chemicals become more water soluble due to higher polarity and are more bio-available, therefore. The present study focussed on plastic leachates of polystyrene (PS) and polylactic acid (PLA), which were derived from alternating stress by hydrolysis and UV radiation. Test specimen of PS, PLA or PS/PLA blends (each 50 %) were alternatingly maintained in water at 45 °C for five days and UV radiated at 45 °C for two days, for in total six weeks. Ecotoxicological effects of potentially generated degradation products of plastic materials in the storage water (mineral water, pH: 7.2) were detected by algae growth inhibition tests with Desmodesmus suspicatus and photosystem II inhibition tests with Raphidocelis subcapitata. Results clearly indicate inhibitory effects on algae growth by contaminants in the storage water of stressed plastic materials with increasing growth inhibition of proceeding hydrolysis and UV stress times. Here, different plastics cause variable responses of algal growth. First chemical analyses indicate dissolved monomers and their oxidation products of plastic materials as possible driver of detected ecotoxicological effects, since detected microplastic particles do not seem to harm algae. The existing data highlight the relevance of plastic aging as a framework for microplastic ecotoxicity evaluation and allow a proof of concept. T2 - SETAC 2023 CY - Dublin, Ireland DA - 30.04.2023 KW - Microplastics KW - Ecotoxicity KW - Plastic aging KW - Algae growth inhibition tests PY - 2023 AN - OPUS4-57501 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Miclea, P.-T. T1 - Micro- and nanoplastic particle number and mass-based analysis on a plastic-free size-selective two stage Si membrane filtration cascade N2 - The poster presents a Si wafer filter development as two stage cascade and the adapter for microplastics filtration. T2 - SETAC Europe 2023 CY - Dublin, Ireland DA - 30.04.2023 KW - Microplastics KW - Filtration KW - TED-GC/MS KW - Polymer 3R KW - Cascade filtration PY - 2023 AN - OPUS4-57461 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Miclea, P.-T. T1 - Real-life airborne micro- and nano-plastic particles and fibres on a porous membrane filter system from a textile factory suitable for both: vibrational and mass spectrometry N2 - The poster presents an application of Si wafer filter system on indoor air sampling. A textile factory producing PP fibres was sampled. T2 - SETAC Europe 2023 CY - Dublin, Ireland DA - 30.04.2023 KW - Microplastics KW - Polymer 3R KW - Textile fibres KW - Si wafer filter KW - Microplastics sampling PY - 2023 AN - OPUS4-57462 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Overview of CUSP and PlasticTrace N2 - The presentation summarises the work of CUSP and PlasticTrace EU joint research projects of the last year. T2 - Microplastics Scientific Workshop of PlasticsEurope CY - Amsterdam, The Netherlands DA - 08.05.2023 KW - Microplastics KW - Microplastics standardisation KW - Reference materials KW - Polymer 3R PY - 2023 AN - OPUS4-57460 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Material Selection Strategy N2 - This poster is a summary of the material used in the PlasticsFatE project. It indicates the strategies for testing of various polymer properties next to each other according to risk and hazard assessment. T2 - CUSP annual meeting and conference CY - Utrecht, Netherlands DA - 12.09.2023 KW - Microplastics KW - CUSP KW - Material selection PY - 2023 AN - OPUS4-58311 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Current projects in risk assessment and harmonisation N2 - The talk gives an overview about EU projects currently running for risk assessment and harmonisation in microplastic analysis. T2 - Micro- and Nanoplastics CY - Halle (Saale), Germany DA - 01.11.2023 KW - Microplastics KW - Harmonisation in microplastics KW - Polymer 3R PY - 2023 AN - OPUS4-58766 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Visileanu, E. T1 - Methods for the collection and characterization of airborne particles in the textile industry N2 - The presentation summarizes possibilities to sample airborne micro and nanoplastic particles. An example of a textil company is shown. T2 - 5th International Conference on Human Systems Engineering and Design: Future Trends and Applications (IHSED 2023 CY - Dubrovnik, Croatia DA - 27.09.2023 KW - Microplastics KW - Polymer 3R KW - Textile company PY - 2023 AN - OPUS4-58561 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kittner, Maria T1 - Bewertung der Freisetzung von Mikroplastik aus Sportböden auf Kunststoffbasis N2 - Projektvorstellung "Bewertung der Freisetzung von Mikroplastik aus Sportböden auf Kunststoffbasis": Motivation, Konzept, Umsetzung, erste analytische Ergebnisse der TED-GC/MS T2 - 24. Projekttage der Zukunft Bau Forschungsförderung CY - Bonn, Germany DA - 13.06.2023 KW - Mikroplastik KW - TED-GC/MS KW - Kunststoffrasen KW - Lysimeter KW - Beschleunigte Alterung PY - 2023 AN - OPUS4-58441 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kittner, Maria T1 - Bewertung der Freisetzung von Mikroplastik aus Sportböden auf Kunststoffbasis N2 - Projektvorstellung "Bewertung der Freisetzung von Mikroplastik aus Sportböden auf Kunststoffbasis": Konzept, Umsetzung, erste Mikroplastik-Ergebnisse. T2 - Projektbegleitkreissitzung des Projektes "Ermittlung und Minderung von Mikroplastik- und Schadstoffemissionen von Kunststoffrasen-Sportplätzen (MiMiK)“ CY - Sittensen, Germany DA - 25.09.2023 KW - Mikroplastik KW - TED-GC/MS KW - Kunststoffrasen KW - Lysimeter KW - Beschleunigte Alterung PY - 2023 AN - OPUS4-58442 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - van den Berg, A. A1 - Adriaans, K. A1 - Hoppener, E. A1 - Parker, L. A1 - Boersma, A. A1 - Altmann, Korinna A1 - Legler, J. A1 - Pieters, R. T1 - Inflammation-related key events stimulated by micro- and nanoplastics N2 - The presence of micro- and nanoplastic particles (MNP) in our environment has raised increasing public and political concern. Increasing evidence suggests that humans are exposed to these MNP, mostly via inhalation or ingestion. The EC-Horizon project POLYRISK (https://polyrisk.science) aims to establish an IATA/AOP-based tiered approach to assess human health risks of MNP. In our research, we focus on assessing immunotoxicological effects of MNP. We have tested a series of primary, secondary, environmentally aged (incubated in River Rine water) and chemically altered MNP for their potential to affect dendritic cells or macrophages. MNP used in this study include primary and weathered PS, secondary PVC, PA, PP (with or without talc) and PE. The secondary PE and PP (w/o talc) particles appeared to have oxidized groups on their surface. Data shows that MNP can be engulfed by macrophages (PMA-stimulated human THP1 cells) and human blood-derived dendritic cells (DCs). The effects of virgin as well as secondary MNP (0, 10 or 100 μg/ml) on THP1 macrophages were limited to decrease of mitochondrial activity (Alamar blue), increase of cellular leakage (LDH), and stimulation of lysosomal activity. None of these MNP stimulated gene expression of NFκB or release of pro-inflammatory cytokines (IL-6, TNFα, IL-1β). On the other hand, secondary PP and PE with oxidized surface groups did increase NFκB gene expression and release of cytokines by THP1 macrophages. Virgin and weathered PS particles were tested using DCs, and only weathered PS did stimulate DC activity (increased costimulatory molecules CD83, CD86) and as consequence allogeneic T cells. DC activation appeared to result from environmental contaminants. In conclusion, of all MNPs tested only those that contained active surface groups or environmental components appeared to be immunostimulatory, whereas primary and secondary MNP rather reduced macrophage activity and viability (at relatively high concentrations of 100 μg/ml). Further research is needed to reveal molecular mechanisms and to translate in vitro findings to real-world exposure scenarios. T2 - 58th Congress of the European Societies of Toxicology (EUROTOX 2024) CY - Copenhagen, Denmark DA - 08.09.2024 KW - Micro- and nanoplastic particles (MNP) KW - Human health risks KW - Immunotoxicological effects PY - 2024 DO - https://doi.org/10.1016/j.toxlet.2024.07.052 AN - OPUS4-63363 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Rossi, A T1 - Lactose Tablets as Suitable Microplastics Reference Material to Support Validation Studies and Quality Control N2 - One of the main challenges in validating microplastics detection methods is the lack of suitable reference materials that accurately reflect the properties of interest. To bridge this gap, the EU-funded PlasticTrace project has developed water-soluble tablets containing precisely defined amounts of polyethylene terephthalate (PET) particles. Each tablet includes a specific mass (0.2, 18.5, or 400 µg) and particle count (151 or 1764, measured via Raman spectroscopy). Production follows a rigorous solid-phase dilution process, ensuring high reproducibility and quality control. The PET particles used in these tablets have an average size of approximately 40 µm, with a range between 10 and 200 µm, and an irregular, stone-like shape. All measurements align with ISO/TC 147/SC 2 standardization efforts and adhere to ISO/DIS 16094-2 and ISO/DIS 16094-3. To assess tablet homogeneity, the most widely accepted microplastics detection techniques, i.e. µ-FTIR, µ-Raman, Py-GC/MS, and TED-GC/MS, were applied. Different batches were produced, each containing varying particle numbers and masses, reaching the detection limits of the methods used. The results demonstrated excellent consistency between tablets, successfully passing homogeneity tests. Furthermore, no significant changes were observed in the tablets' composition or stability after six months of storage. This innovative reference material represents an important advancement in microplastics analysis, supporting laboratories in meeting EU Commission requirements for the monitoring of microplastics in drinking water and wastewater with greater accuracy and reliability. The production process can be transferred for other plastic particles is this size range. T2 - BERM 16 CY - Halifax, Canada DA - 01.06.2025 KW - Microplastics KW - TED-GC/MS KW - Reference materials KW - Raman microscopy PY - 2025 AN - OPUS4-63403 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Fernández-González, V. T1 - Innovations in Microplastic Measurement: A Pyrolysis Approach for a Polyethylene Terephthalate Reference Material N2 - In the framework of the PlasticTrace project, in which a reference material for PET microplastics will be proposed, a method using pyrolysis and gas chromatography coupled with mass spectrometry detection (Py-GC-MS) is developed to quantify the mass of PET microplastics (10-100 µm) in tablets at two different concentration levels. The overall aim of this project is to develop international metrological capacity that enables the traceable measurement and characterization of SMPs and NPs in environmental and food samples and the production of suitable reference materials, according to the metrological requirements (https://plastictrace.eu/). The proposed method consists of dissolving the tablet containing the PET microplastics in milli-Q water and filtering the solution using a glass microfiber membrane 13 mm filter size, 1.6 µm pore size. After filtering and several washes to ensure complete dissolution of the tablet and recovery of all PET microplastics, the filter is removed, folded, and placed in a capsule of the pyrolyzer for direct Py-GC/MS analysis. Two main markers were selected for PET quantification: vinyl benzoate and benzoic acid, with consistent concentrations found for both at high PET concentrations (≈400 µg) (24% RSD, n=17), but interferences with the matrix and vinyl benzoate were found at low concentrations (≈17 µg PET), with only benzoic acid being valid as a marker in this case (22% RSD, n=10). As an alternative to the quantification of PET microplastics in tablets at low concentrations, derivatization is proposed, for which tetramethylammonium hydroxide solution (TMAH) is added directly into the pyrolysis cap. The PET marker in this case is dimethyl terephthalate, with which good results have also been found (19.6% RSD, n=10 ). The proposed method is robust, simple, with high automation and very little sample handling and treatment, and allows the analysis of PET microplastics (>10 µm) in tablets with excellent accuracy and precision even at very low concentrations. T2 - SETAC Europe 2025 CY - Vienna, Austria DA - 11.05.2025 KW - Microplastics KW - Nanoplastics KW - GC/MS PY - 2025 AN - OPUS4-63383 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kühnel, D. T1 - Micro and nanoplastics (MNP) a wish list for reliable determination of the risks for humans N2 - The assessment of risks to human health from micro- and nanoplastics (MNPs) and their associated chemicals is hampered by significant uncertainties and data gaps regarding human exposure, biological fate and potential health effects. There is also a notable lack of validated test MNPs, natural particles to serve as reference controls, and lack of harmonised toxicological assessment methods specifically designed for the unique properties of MNPs. These limitations contribute to data scarcity and further complicate exposure and hazard assessment for MNP and their associated chemicals. The European research cluster CUSP (https://cusp-research.eu/) aims to fill these gaps by providing reliable data and suggests approaches for assessing human exposure and health risks associated with MNPs and their associated chemicals, including contaminants. As part of this initiative, five projects address the health risks of MNPs from different perspectives, focusing on different exposure pathways and health effects. In particular, the PlasticsFatE project (https://www.plasticsfate.eu/) structures the data requirements and developes strategies to overcome both general and material-specific barriers to MNP in hazard and risk assessment. Based on safety research on engineered nanomaterials, which has shown that it is impossible to experimentally test all MNP variants and their chemical mixtures, CUSP emphasises the need for pragmatic approaches. These approaches aim to effectively utilize knowledge from nanomaterial research, emphasize the reuse of generated data on fate and effects of MNPs, as well as identify and address data and knowledge gaps along with uncertainties, while considering the specific properties of MNPs and test approaches. This poster provides a structured overview of the current challenges in the risk assessment of micro- and nanoplastics and introduces the first step of categorising the different types of obstacles. Specific strategies to overcome these different types of challenges will be presented. T2 - SETAC Europe 2025 CY - Vienna, Austria DA - 11.05.2025 KW - Microplastics KW - Nanoplastics PY - 2025 AN - OPUS4-63385 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Booth, A. T1 - Production of a 1-10 μm polypropylene reference material for development of analytical methods N2 - The poster is about the preparation of microplastics in the size range of 1-10 µm. These size range of particles can be inhalded and therefore be toxic for humans. The preparation is done by comminution of PP pellets and sieving. Characterisation occured for size with laser diffraction, for type with FTIR and for shape with SEM. T2 - SETAC Europe 2025 CY - Vienna, Austria DA - 11.05.2025 KW - Microplastics KW - Reference materials PY - 2025 AN - OPUS4-63367 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Miclea, P.-T. T1 - Novel laser pre-structured silicon filters for microplastics analysis N2 - This research presents a novel laser-assisted approach to silicon filter fabrication, offering an effective alternative to traditional photolithographic processes. By integrating selective femtosecond laser irradiation with photoelectrochemical etching, we achieved precisely controlled pore geometries, overcoming common challenges in filter production for microplastic and nanoscale filtration suitable for microplastic number and mass analysis. T2 - SETAC Europe 2025 CY - Vienna, Austria DA - 11.05.2025 KW - Microplastics KW - Nanoplastics KW - Raman microspectroscopy PY - 2025 AN - OPUS4-63384 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Putzu, Mara T1 - Optimization of production process for microplastics reference materials N2 - Microplastics (MP) are defined as plastic particles mainly consisting of polymers in the size range of 1 to 1000 µm. They can be found in a wide range of environmental matrices but also in food products, indicating a potential risk on humans and environment. Plastic debris in the environment or food chain are extremely complex in terms of size, concentration, polymer type, levels of physiochemical degradation and undefined morphologies which makes their isolation and detection in complex matrices challenging. Analytical detection methods and techniques to identify and quantify microplastics in environmental and food matrices are numerous but validated and standardized methods are currently lacking. To close this research gap, reference materials (RMs) and representative sample preparation approaches are urgently needed. Homogeneity and stability are two crucial characteristics for the certification process of the reference materials. For this purpose, we aim to present ways to prepare reference materials containing very low masses of close-to reality plastic particles with broad size distribution (10-100 µm) that are homogeneously distributed in tablet-to-tablet variation and stable over time. Our work is based on the ISO Guide 30:2015 and ISO Guide 35:2017 to fulfil the criteria set in future standards ISO/DIS 16094-2 and ISO/DIS 16094-3. The property of interest will be the mass detected by thermogravimetric analysis (TGA). Furthermore, informative values will be achieved by mass-based technique TED-GC/MS and spectroscopic microscopy techniques, such as µ-FTIR spectroscopy and µ-Raman. T2 - SETAC Europe 2025 CY - Vienna, Austria DA - 11.05.2025 KW - Microplastics KW - Reference materials KW - TED-GC/MS PY - 2025 AN - OPUS4-63386 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ryll, Tom William T1 - In-situ analysis of nucleation processes – case study: calcium sulfate N2 - In this project we investigate nucleation pathways by utilizing synchrotron-XRD and running a case-study on calcium sulfate phases. To accomplish this, we developed a modular automation setup for reactions in solution to run synthesis and control reaction conditions. So far we successfully characterized the recycling process of gypsum and are now investigating the formation of anhydrite. T2 - BESSY@HZB User Meeting CY - Berlin, Germany DA - 02.12.2025 KW - Recycling KW - Gypsum KW - Synchrotron-X-ray-diffraction KW - Raman-spectroscopy KW - Automation PY - 2025 AN - OPUS4-65344 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Jaffer, Yousuf Dar A1 - Abdolahpur Monikh, Fazel A1 - Nguyen, Nhung H.A. A1 - Sevcu, Alena A1 - Abdulkadir, Nafiu A1 - Raha, Jakub A1 - Katsumiti, Alberto A1 - Bilbao, Ainhoa A1 - Altman, Korinna A1 - Grossart, Hans-Peter T1 - Bio-based microplastics increase the horizontal transfer of antibiotic resistance genes in aquatic environments N2 - The role of microplastics as vectors for horizontal gene transfer (HGT) of antibiotic resistance genes (ARGs) is increasingly recognized. This study investigated whether bio-based microplastics, often promoted as environmentally friendly alternatives, exhibit similar or enhanced HGT potential compared to conventional plastics. We examined the HGT rates of the trimethoprim resistance gene (dfrA1) and tetracycline resistance gene (tetA), carried on a broad-host-range plasmid, among Escherichia coli (donor) and Vibrio parahaemolyticus, Pseudomonas sp., or a natural lake microbial community (recipients). Four bio-based polymer types—polylactic acid (PLA) granules, commercial PLA, high-density polyethylene (HDPE) granules, and poly(3-hydroxybutyrate-co-3-hydroxyvalerate) (PHBV)- were compared with two conventional microplastics, polyethylene terephthalate (PET) and bottle-derived HDPE. The bio-based microplastics exhibited significantly higher HGT frequencies, with a 21–48-fold increase compared to control chitosan in single-strain experiments and a 13-fold increase within the lake microbial community. 16S rRNA amplicon sequencing revealed distinct bacterial community compositions colonizing different microplastic types in the lake water. The transconjugant communities, indicative of successful HGT events, were strongly influenced by microplastic type. While Nannocystis was generally dominant, the PLA (granule) microplastic exhibited a unique profile dominated by Candidatus Megaira and Niveispirillum. Additionally, Flavobacterium and Fluviicola were uniquely detected as transconjugants on HDPE (granule). These findings demonstrate that bioplastics have a significant influence on the selective enrichment of specific transconjugant genera, suggesting a prominent role of microplastics, particularly bio-based plastics, in shaping ARG dissemination within complex microbial ecosystems. We recommend a comprehensive risk assessment of bio-based plastics, particularly their potential to enhance the spread of ARGs, before their widespread implementation in consumer products. KW - Microplastics KW - Bioplastics KW - Conventional plastics KW - Antibiotik resistence gene PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-656293 DO - https://doi.org/10.1016/j.impact.2026.100613 SN - 2452-0748 VL - 41 SP - 1 EP - 10 PB - Elsevier B.V. AN - OPUS4-65629 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Herzel, Hannes T1 - Thermochemische P-Rückgewinnungsverfahren in Deutschland zur Düngerproduktion N2 - Die Firma Emter GmbH betreibt die Klärschlammverbrennungsanlage Altenstadt und hat in die bestehende Monoverbrennung einen thermochemischen Prozess integriert, um hochwirksame und schadstoffarme Düngemittel aus Klärschlamm herzustellen. Die Anlage ist aktuell die größte Phosphorrecyclinganlage in Deutschland mit der die Vorgaben der AbfKlärV bereits frühzeitig umgesetzt werden. Das Projekt R-Rhenania begleitet die Phosphorrecyclinganlage mit Untersuchungen zur Produktqualität, mit Gefäßversuchen und Feldversuchen im ökologischen Landbau, mit Ökobilanzierung und der Konfektionierung verschiedener Düngemittelprodukte. Viele Klärschlammaschen haben geringe Schwermetallgehalte und sind geeignet durch vergleiche thermochemische Prozesse behandelt zu werden. Mit den Daten aus dem Klärschlammasche-Monitoring der BAM können die Potentiale für die Verwertung der Aschen in den thermochemischen Prozessen wie AshDec oder CaNaPhos abgeschätzt werden. T2 - DWA Klärschlammnetzwerk Nord-Ost CY - Berlin, Germany DA - 21.01.2026 KW - Phosphor KW - Recycling KW - Thermochemisch KW - Großtechnik PY - 2026 AN - OPUS4-65611 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Seifert, Lando T1 - Grundlagen Korrosion und Korrosionsschutz N2 - Im Rahmen des jungen gfkorr Events an der Universität Kassel in diesem Jahr wurde der Grundlagenvortrag vor Young Professionals und Studierenden vorgestellt. Die BAM beschäftigt sich im Fachbereich 7.6 schwerpunktmäßig mit der Korrosionsprüfung, den Korrosionsschäden und -reaktionen rund um Anwendungsfälle der Hauptkonstruktionswerkstoffe Stahl, verzinkter Stahl, Nichtrostende Stähle und Aluminium in relevanten Umgebungsbedingungen. Der Impulsvortrag sollte die Faszination für die Korrosion übermitteln. Dabei wurde anhand von Schadensfällen grundlegende Mechanismen und Haupteinflussfaktoren erörtert. Gestartet wurde mit einem prominenten Versagensfall und Beispiel für Spaltkorrosion aus der Luftfahrt... T2 - die junge gfkorr @ Universität Kassel CY - Kassel, Germany DA - 02.03.2026 KW - Korrosion KW - Korrosionsschutz KW - Stahl KW - Zink KW - Aluminium KW - Nichtrostende Stähle KW - Korrosivität KW - Spaltkorrosion PY - 2026 AN - OPUS4-65614 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Lohrke, Heiko T1 - Combined GNSS/Visual Inter-Robot Tracking Method for Open-Path Gas Tomography N2 - Methane emissions are a significant environmental and safety concern, yet many gas tomography systems intended to measure them require manual alignment, reliable high-bandwidth links, or fiducials. We present a lightweight, fully autonomous framework enabling line-of-sight inter-robot Tunable Diode Laser Absorption Spectroscopy (TDLAS) measurements without such constraints. A sensor robot equipped with a gimbal-mounted TDLAS unit tracks a reflector robot bearing an illuminated, color-controllable target. Coarse localization is achieved via RTK-GNSS, with vision-based fine tracking and passive time synchronization handled onboard. The system, based on off-the-shelf Pixhawk controllers and ArduPilot firmware, was validated in a 15m × 7m outdoor trial. Despite GNSS inaccuracies and deliberate occlusion by a methane-filled bag, the system retained lock, recovered from visual loss in under one second, and captured a 2800 ppm·m plume signature. These results demonstrate robust, scalable methane sensing for mobile gas tomography or standalone leak detection. Core components are released open-source to support future deployment. T2 - IEEE SENSORS 2025 CY - Vancouver, BC, Canada DA - 19.10.2025 KW - Gas tomography KW - Tracking KW - Robot KW - Methane KW - TDLAS PY - 2025 AN - OPUS4-65617 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schlegel, Moritz-Caspar T1 - Die Ökodesign-Rahmenverordnung - Produkteffizienz neu gedacht N2 - Die Präsentation fasst das europäische Verständnis für den Begriff "Produkteffizienz" und die diesbezügliche Entwicklungen der vergangenen Jahre zusammen. Es wird eine Verbindung zwischen Rechtssetzung, Normung und Forschung hergestellt und entsprechende Beiträge zur der Transformation von einer linearen- zu einer zirkulären Wirtschaft (Circular Economy) erörtert. T2 - DIN-Mitgliederdialog CY - Berlin, Germany DA - 03.03.2026 KW - Circular economy KW - Product efficiency KW - Normung KW - Ecodesign KW - Policymaking PY - 2026 AN - OPUS4-65631 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian T1 - Investigating the Thermal Decomposition of PFAS in a Full-Scale Commercial Hazardous Waste Incinerator N2 - Effective and safe treatment of per- and polyfluoroalkyl substances (PFAS)-laden waste in full-scale hazardous waste facilities is currently the only commercial method for large-scale PFAS destruction, but concerns remain about incomplete combustion and harmful byproducts. Therefore, the fate of fluorine during incineration was investigated in a full-scale hazardous waste incinerator to assess the viability and potential risks of this method. The project involves developing advanced analytical tools, including real-time infrared spectroscopy, and conducting trial burns under varied conditions. Conditions that influence incineration performance are identified, analyzing for products of incomplete destruction (PIDs), exploring the role of fly ash and surfaces in PFAS breakdown, and evaluating the potential formation of polyfluorinated dioxins and furans. Collectively, these tasks aim to deliver practical tools and guidance for scientists and engineers, while informing policymakers and the public on the benefits and potential risks of PFAS incineration. T2 - DoW Applied Innovation Workshop CY - Washington, DC, USA DA - 02.03.2026 KW - Per- and polyfluoroalkyl substances (PFAS) KW - Incineration PY - 2026 AN - OPUS4-65638 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Miclea, Paul T1 - Microanalysis of Airborne Nano/Microplastic Particles in an Textile Industrial Environment N2 - Micro- and nanoplastics (MNPs) are emerging global contaminants, present in air, soil, and water. The textile industry is potentially a major contributor, releasing synthetic particles like polyamide, polyester, and acrylic during production. This study assessed MNP levels outside and inside a textile-processing facility using online air samplers with silicon (Si) and quartz filters. Real-time particle counts (PM0.3–PM10) were obtained via a laser detector. Si filters (9 mm, 10/1 µm pores) and quartz filters (25 mm, 1.2 µm pores, pre-calcined at 800°C) were used for sampling. Custom holders allowed selective sampling for PM10 and PM1 on Si filters. Sampling conditions included a 3-hour collection at 2 L/min (GilAir Plus pump) starting at 7:00 AM (T1) and 2:00 PM (T2), with intermittent ventilation, 23.3 °C average temperature, and 52.5% humidity. Particle weights collected (µg) were: quartz – 4.9E-05 (T1), 5.1E-05 (T2); Si – 3.2E-05 (T1), 5E-06 (T2). Outside particle counts ranged from 3,584 (T1) to 15,165 (T2); inside: 9,901 (T1) to 12,921 (T2). Maximum indoor PM10 and PM0.3 levels were 72/m³ and 71,979/m³, respectively. Particles were analyzed using electron microscopy and µRaman spectroscopy, confirming high concentrations of irregularly shaped PP-based particles (1–5 µm). T2 - 12th TEXTEH CY - Bucharest, Romania DA - 23.10.2025 KW - Microplastics KW - Airborne particles KW - Raman microspectroscopy PY - 2025 AN - OPUS4-64485 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Monikh, F. A. A1 - Baun, A. A1 - Hartmann, N. B. A1 - Kortet, R. A1 - Akkanen, J. A1 - Lee, J.-S. A1 - Shi, H. A1 - Lahive, E. A1 - Uurasjärvi, E. A1 - Tufenkji, N. A1 - Altmann, Korinna A1 - Wiesner, Yosri A1 - Grossart, H.-P. A1 - Peijnenburg, W. A1 - Kukkonen, J. V. K. T1 - Exposure protocol for ecotoxicity testing of microplastics and nanoplastics N2 - Despite the increasing concern about the harmful effects of micro- and nanoplastics (MNPs), there are no harmonized guidelines or protocols yet available for MNP ecotoxicity testing. Current ecotoxicity studies often use commercial spherical particles as models for MNPs, but in nature, MNPs occur in variable shapes, sizes and chemical compositions. Moreover, protocols developed for chemicals that dissolve or form stable dispersions are currently used for assessing the ecotoxicity of MNPs. Plastic particles, however, do not dissolve and also show dynamic behavior in the exposure medium, depending on, for example, MNP physicochemical properties and the medium’s conditions such as pH and ionic strength. Here we describe an exposure protocol that considers the particle-specific properties of MNPs and their dynamic behavior in exposure systems. Procedure 1 describes the top-down production of more realistic MNPs as representative of MNPs in nature and particle characterization (e.g., using thermal extraction desorption-gas chromatography/mass spectrometry). Then, we describe exposure system development for short- and long-term toxicity tests for soil (Procedure 2) and aquatic (Procedure 3) organisms. Procedures 2 and 3 explain how to modify existing ecotoxicity guidelines for chemicals to target testing MNPs in selected exposure systems. We show some examples that were used to develop the protocol to test, for example, MNP toxicity in marine rotifers, freshwater mussels, daphnids and earthworms. The present protocol takes between 24 h and 2 months, depending on the test of interest and can be applied by students, academics, environmental risk assessors and industries. KW - Microplastics KW - TED-GC/MS KW - Cryo milling PY - 2023 DO - https://doi.org/10.1038/s41596-023-00886-9 SN - 1754-2189 SP - 1 EP - 38 PB - Nature Protocols AN - OPUS4-58557 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - ILC on Laser diffraction - preliminary results N2 - This presentation addresses an interlaboratory comparison on size of polymeric particles (microplastics) measured by laser diffraction. Two microplastic particles were measured separately and once as mixture. Evaluation was done with Fraunhofer and Mie. Here, the first results are presented. T2 - CUSP Annual Meeting CY - Utrecht, Netherlands DA - 12.09.2023 KW - Microplastics KW - Laser diffraction KW - Polymer 3R KW - Size distribution KW - Polymer size PY - 2023 AN - OPUS4-58318 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Drexel, R. T1 - Nano-sized Polypropylene as a Promising Candidate Reference Material: Preparation, Characterization and Stability in Complex Matrices N2 - The lack of nanoplastic (NPs) reference materials capable of mimicking real-world scenarios is currently hampering the development of validated extraction techniques from complex matrices (e.g. soils, sediments, biota), the development of analytical approaches for robust identification and quantification, and the ability to use environmentally relevant test materials in (eco)toxicity testing and hazard assessment [1]. The large body of available data suggests that larger microplastics (MPs) in the natural environment are irregular shaped, partially degraded (chemically and physically), a continuum of sizes, shapes and densities, represent a wide range of polymer types, and acts as a reservoir for thousands of plastic chemicals. Although NPs have been described as being neither MPs nor engineered nanoparticles [2], and while direct measurement data of true NP in the environment remain elusive, they are expected to be as equally diverse as MPs [3]. Here, we present a strategy towards the development of a potential NP reference material based on nano-sized polyproplyene particles (nanoPP) developed within the EURAMET-funded PlasticTrace project (https://plastictrace.eu/). The strategy includes the preparation, the physicochemical characterization and the stability assessment of nanoPP in suspension both in its pristine state, but also when spiked into food (mineral water and milk) and environmental matrices (suspended particulate matter collected from the river Elbe ). Collected experimental data suggests nanoPP to be a promising candidate for a NP reference material. T2 - SETAC Europe 2025 CY - Vienna, Austria DA - 11.05.2025 KW - Nanoplastics KW - Reference materials PY - 2025 AN - OPUS4-63382 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Validation of microplastics detection methods and proficiency testing: Suitable microplastic reference materials for interlaboratory comparison N2 - The talk summarizes challenges in microplastic analysis. It shows the preparation of microplastic reference materials as well as the testing on homogeneity and stability. The reference material is used in an international laboratory comparison to compare different detection methods used for microplastic analysis. The methods used were µ-IR (FTIR+LDIR) for number-based methods and TED-GC/MS and Py-GC/MS for mass-based methods. The ILC was done under the umbrella of VAMAS TWA 45. Results of the participants are presented. T2 - BAM Akademie CY - Online meeting DA - 16.05.2024 KW - Microplastics KW - Reference materials KW - ILC KW - Microplastics detection KW - TED-GC/MS KW - Polymer 3R PY - 2024 AN - OPUS4-60085 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Mikroplastik Detektion mit Thermoanalytischen Methoden: Analytik, Referenzmaterial, Ringversuche N2 - Ich dem Vortrag geht es um die Vorstellung von thermoanalytischen Methoden für die Mikroplastik-Detektion. Verschiedene Kopplungsmöglichkeiten werden gezeigt und die Funktionsweise der TED-GC/MS wird erklärt. Im zweiten Teil werden Referenzmaterialien für die Mikroplastik-Analytik diskutiert. PET -Tabletten des PlasticTrace Projektes werden vorgestellt. Am Ende wird der VAMAS Ringversuch zur Mikroplastik-Detektion gezeigt. T2 - Plastik, Mikroplastik, Nanopartikel, PFAS und Verunreinigungen (Agilent Workshop) CY - Hamburg, Germany DA - 28.05.2024 KW - Mikroplastik KW - TED-GC/MS KW - Polymer 3R KW - Ringversuche KW - Referenzmaterial PY - 2024 AN - OPUS4-60155 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Giovannozzi, A T1 - Metrological traceability of measurement data from nano- to small microplastics for a greener environment and food safety N2 - This talk descibes the EMPIR project PlasticTrace. Reference materials for microplastics will be developed. The production process and characterisation is explained by SEM, Raman, IR, Py-GC/MS and TED-GC/MS. Homogeneity control was successful. Stability check show no changes over 6 month. T2 - SETAC Europe 2024 CY - Sevilla, Spain DA - 05.05.2024 KW - Microplastics KW - Reference materials KW - Polymer 3R KW - TED-GC/MS PY - 2024 AN - OPUS4-60033 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Drago, C. T1 - Standardization Methods for the Analysis of Microplastics (10 100µm) in Food Matrix: Sample Preparation and Digestion of Milk Powder. N2 - Monitoring of microplastics in food matrices is crucial to determinate the human exposure. By direct ingestion microplastics could be released in the food during the production, through packaging and by consumer’s use. The absence of standard methods to quantify and detect different size range and type of microplastics has led to difficult and time consuming procedural steps, poor accuracy and lack of comparability. In this work, matrix characterization and laboratory experiments were used to investigate the efficiency of sample preparation in milk powder. This information is crucial to compile a standard procedure for sample preparation and digestion of common milk powder to detect different particle sizes and types of polymers. Charaterisation is done by TGA and TOC measurements. T2 - SETAC Europe 2024 CY - Sevilla, Spain DA - 05.05.2024 KW - Microplastics KW - Harmonisation in microplastics KW - Polymer 3R KW - Microplastics in milk PY - 2024 AN - OPUS4-60034 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Vogel, Christian T1 - Investigating the Thermal Decomposition of PFAS in a Full-Scale Commercial Hazardous Waste Incinerator (SERDP ER24-4073) N2 - Effective and safe treatment of per- and polyfluoroalkyl substances (PFAS)-laden waste in full-scale hazardous waste facilities is currently the only commercial method for large-scale PFAS destruction, but concerns remain about incomplete combustion and harmful byproducts. Therefore, the fate of fluorine during incineration was investigated in a full-scale hazardous waste incinerator to assess the viability and potential risks of this method. The project involves developing advanced analytical tools, including real-time infrared spectroscopy, and conducting trial burns under varied conditions. Conditions that influence incineration performance are identified, analyzing for products of incomplete destruction (PIDs), exploring the role of fly ash and surfaces in PFAS breakdown, and evaluating the potential formation of polyfluorinated dioxins and furans. Collectively, these tasks aim to deliver practical tools and guidance for scientists and engineers, while informing policymakers and the public on the benefits and potential risks of PFAS incineration. T2 - DoW Applied Innovation Workshop CY - Washington, DC, USA DA - 02.03.2026 KW - Per- and polyfluoroalkyl substances (PFAS) KW - Incineration PY - 2026 AN - OPUS4-65639 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Update – Milling and weathering of granules N2 - The talk aims to describe the production of microplastic particles as test material and the additional weathering for aged particles. T2 - PlasticsFate meeting CY - Online meeting DA - 12.11.2021 KW - Microplastic KW - Cryo milling KW - Aged particles PY - 2021 AN - OPUS4-53737 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kittner, Maria T1 - Beschleunigung und Hemmung - Komplexe Wechselwirkungen bei der Zersetzung von thermoplastischen PLA/PS-Blends unter realitätsnahen Umweltbedingungen N2 - Mit dem stetigen weltweiten Anstieg der Nachfrage nach Polymerprodukten nimmt auch die potenzielle Menge an Kunststoffabfällen in der Umwelt zu. Problematisch ist, dass viele der wirtschaftlich relevantesten Kunststoffe sehr lange brauchen, um in der Umwelt abzubauen, sich dort akkumulieren und in kritisch betrachtetes Makro- und Mikroplastik zu zerfallen. Auf der Grundlage des Vorsorgeprinzips fordert die Europäische Kommission daher die Entwicklung neuer polymerer Materialien, die diesem Problem der Persistenz entgegenwirken und unter natürlichen Umweltbedingungen schneller abgebaut werden können. 1,2 Um dieses Problem anzusprechen, wurden mittels additiver Fertigung Polymerblends aus photooxidationsempfindlichem Polystyrol (PS) und hydrolyseempfindlicher Polymilchsäure (PLA) hergestellt. Die Hypothese war, dass sich die beiden Thermoplaste aufgrund ihrer unterschiedlichen Abbauprozesse gegenseitig in ihrem Abbau unterstützen, wenn sie unter moderaten, realitätsnahen Umweltalterungsbedingungen (45 °C) abwechselnd der Photooxidation und Hydrolyse ausgesetzt werden. In der Praxis zeigten die Ergebnisse, dass die Degradation von PLA durch die Anwesenheit von PS deutlich beschleunigt worden ist – wohingegen die Degradation von PS gehemmt wurde. In diesem Vortrag werden die detaillierten Ergebnisse der Oberflächen- (ATR-FTIR, REM) und Bulk-Analysen (DSC, TGA, FTIR-Transmission, TED-GC/MS) der Blends sowie ergänzende Mikroplastik-Ergebnisse des umgebenden Wassermediums (TED-GC/MS) erörtert. T2 - 50. Jahrestagung der Gesellschaft für Umweltsimulation (GUS) CY - Online meeting DA - 23.03.2022 KW - Polymerblend KW - PLA KW - Hydrolyse KW - PS KW - Bewitterung KW - UV-Bestrahlung KW - TED-GC/MS KW - Wasser KW - Mikroplastik PY - 2022 AN - OPUS4-54544 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Plastik in Böden: Mikroplastik-Analytik N2 - Im Vortrag wir eine Methode zur Analyse von Mikroplastik in Böden dargestellt. Es geht dabei um die Probenvorbereitung und Detektion. T2 - Fachgespräch "Plastik in Böden" CY - Online meeting DA - 28.03.2022 KW - Mikroplastik KW - TED-GC/MS KW - Mikroplastik-Analytik KW - Methodenentwicklung Böden PY - 2022 AN - OPUS4-54646 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Plastik in Böden: Mikroplastik-Ergebnisse N2 - In diesem Vortrag geht um die Vorstellung der Ergebnisse des UBA Projektes Plastik in Böden. Es werden Mikroplastik-Gehalte in verschiedenen Böden präsentiert. T2 - Fachgespräch "Plastik in Böden" CY - Online meeting DA - 28.03.2022 KW - Mikroplastik KW - Mikroplastik Böden KW - Mikroplastik-Analytik PY - 2022 AN - OPUS4-54648 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ryll, Tom William T1 - In-situ analysis of nucleation processes – case study: calciumsulfate N2 - In this project we investigate nucleation pathways by utilizing synchrotron-XRD and running a case-study on calcium sulfate and its polymorphs. To accomplish this, we developed a modular automation setup for reactions in solution to run synthesis and control reaction conditions. So far we successfully characterized the recycling process of gypsum (CaSO4*2H2O) and are now investigating the formation of anhydrite (CaSO4*0H2O) as well as possible applications for the automation setup and analysis. T2 - SALSA Make & Measure 2025 CY - Berlin, Germany DA - 10.09.2025 KW - Recycling KW - Gypsum KW - Synchrotron-X-ray-diffraction KW - Raman-spectroscopy KW - Automation PY - 2025 AN - OPUS4-64138 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Parthasarathy, Thiyagaraj A1 - Bhattacharya, Biswajit A1 - Emmerling, Franziska A1 - Ghosh, Soumyajit T1 - Design of mechanically flexible photoresponsive cyanostilbene molecular crystals N2 - Photoresponsive molecular crystals have sparked interest owing to their potential application prospects. In this study, we achieved dual mechanical responses of a cyanostilbene-based crystal BN. The crystal exhibited both stress-induced mechanical flexibility and light-induced photomechanical bending. Two distinct mechanical responses are related to different underlying phenomena and were not interlinked. While elasticity is attributed to criss-cross packing arrangement in the isotropic structure, photomechanical bending is attributed to the formation of heterogeneous phase distribution due to monomer to dimer cycloaddition product formation. The crystal did not demonstrate photoswitching activity. However, it exhibited thermal reversibility, highlighting reversible dimer to monomer conversion. KW - Flexible KW - Molecular crystals PY - 2024 DO - https://doi.org/10.1039/D4CE00571F VL - 26 SP - 4634 EP - 4642 PB - Royal Society of Chemistry (RSC) AN - OPUS4-60888 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Mikroplastik heute: Was haben wir in den letzten Jahren erreicht? N2 - In diesem Vortrag geht es um eine Übersicht über die Thematik der Mikroplastik, Was ist Mikroplastik, wie entsteht es und wo kommt es her. Es wird beschrieben wie eine repräsentative Probenahme erfolgen kann und wie welche Herausforderungen bei der Probenvorbereitung existieren. Die Detektion wird ausführlich beschrieben, sowohl mit Partikelanzahl als auch Masse. Im weiteren werden erste Referenzmaterialien und ihre Anwendung in internationalen Ringversuchen beschrieben. Der zweite Teil zeigt die Normungsaktivitäten im Bereich der Mikroplastik. T2 - Mitgliederversammlung der GdCh Lackchemie CY - Online Meeting DA - 20.09.2024 KW - Mikroplastik KW - TED-GC/MS KW - Polymer 3R KW - Reference material KW - ILC on detection methods PY - 2024 AN - OPUS4-61087 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Kittner, Maria T1 - Contaminant Emissions from Artificial Turf Sports Pitches - Simultaneous sampling for Microplastics, PAH and Heavy Metals N2 - In September 2023, the European Commission introduced a new regulation to reduce microplastic (MP) emissions into the environment, including the sale and use of intentionally added (large) MP < 5 mm (ISO/TR 21960: 2020). This explicitly applies to the use of synthetic rubber granulate infill in artificial turf installations, which are complex multi-component systems consisting of multiple synthetic polymers (Fig. 1). In addition, abrasions of synthetic grass fibres and other turf components are also considered as MP sources. Although this has a major impact on public recreational sports, there is so far no sufficient data to estimate the MP emissions from artificial turf sports pitches into the environment and thus their relevance as a source of MP pollution. To close this gap, this study compared environmental contaminant emissions of three artificial turf scenarios at different ageing states (unaged, artificially and real-time aged): the past (old turf: fossil based, synthetic infill), present (most commonly installed in Germany: fossil based, EPDM infill) and future (turf with recycled grass fibres, no synthetic infill). Accelerated ageing by UV weathering and mechanical stress was carried out to simulate the outdoor weathering during the lifespan of approx. 15 years. MP emissions and released environmentally relevant contaminants posing a risk to the groundwater were simultaneously sampled using the newly developed Microplastic Eluate Lysimeter manufactured at BAM (Fig. 2). MP contents were analysed using smart microfilter crucibles (mesh size: 5 μm) with subsequent MP detection by TED-GC/MS. Additionally, concentrations of polycyclic aromatic hydrocarbons were determined using GC/MS and heavy metals using ICP-AES. T2 - 22nd European Symposium on Polymer Spectroscopy (ESOPS) CY - Berlin, Germany DA - 08.09.2024 KW - Microplastics Eluate Lysimeter KW - Microplastics KW - TED-GC/MS KW - Heavy Metals KW - PAH PY - 2024 AN - OPUS4-61013 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Miclea, Paul-Tiberiu T1 - Membrane filter cascade for size-selective analysis of nano-and micro particles N2 - From a metrological point of view, the analysis of micro and nanoplastics MNP requires not only representative and meaningful methods for sampling, preparation, and detection, but also defined and reproducible analytical procedures for the processes and materials used. For such a validation of the detection procedures (including the determination of process and laboratory blank values), the filters and laboratory conditions used in interaction with the final MNP measurement play a central role for detection limits regarding MNP size, MNP content and statistical measurement control, in addition to the reference materials mentioned above. On the basis of available filtration materials (e.g. metal mesh, silicon, aluminum oxide, polycarbonate) and metrological boundary conditions, key aspects for metrologically sound method development must be defined. Two key categories of analysis are developed for the characterization of MNP’s: analytical methods (e.g. µ-IR spectroscopy, µRaman) and mass spectrometry (eg. Py-GC/MS or TED-GC/MS). If in the first category the shape, size, number of particles and the size distribution present in the samples can be determined. In the second category the mass of the material can be measured and the volume of plastic present in the samples can be deduced from this. Both catagories are very sensitive in terms of the volume of material that can be analyzed; vibrational methods can detect single particles but mass-based method require enough particles to reach the limit of detection. That is why in this study we propose a filtration system, which in our opinion brings the two categories much closer to each other and allows true measurements of particle number and mass of the same sample. In this way it is possible not only to estimate the volume of plastic in the sample, but also to determine with much greater precision the number of particles and the type of plastic present. Furthermore, new methods for particle detection can be added and combined with existing methods. Our proposed system can be used for a single filter, but also for the use of several filters in cascade. In this way a separation of particles by size can be achieved. T2 - 13th Annual World Congress of Nano Science & Technology 2024 CY - Osaka, Japan DA - 22.05.2024 KW - Microplastics KW - Si filters KW - Filtration KW - Polymer 3R PY - 2024 AN - OPUS4-61097 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Drago, Claudia T1 - Rapid sample preparation to detect microplastics in baby milk powder N2 - Microplastics, ubiquitous as it is, could be released into food during production chain, through packaging and by consumer´s use. To determinate human exposure to microplastics is crucial to monitor microplastics in food matrices. The current absence of standard sample preparation procedures to identify and quantify different microplastics according to number and mass have generate time-consuming protocols and lack of comparability among different analytical methods, laboratories and time scales. Monitoring microplastics in complex matrices as food, and in particular in baby milk powder, requires an accurate approach that need to be validate, to ensure the comparability of results. Bottled drinking water or surface waters, for example, can be measured with mass-based methods (TED-GC/MS or Py-GC/MS) directly after filtration. Baby milk powder, instead is more challenging, due to the proteins and fatty acid that clog the filters and contaminate the measuring devices with heavy carry over. In this study, we characterize the baby milk powder by thermogravimetric analysis (TGA) and we tested different treatments for matrix reduction: water, H2O2, citric acids. In particular, the use of citric acid was tested for protein reduction before filtration. Our hypothesis was that citric acid will induce the precipitation of proteins and amino acids, leading to a strong matrix reduction. In fact, this sample pre treatment, allowed us to use a higher intake, necessary for representative quantification. Finally, the milk powder was spiked with reference material tablets containing polyethylene terephthalate (PET). The PET was not degraded by the citric acid and high recovery rate was achieved by TED-GC/MS and Py-GC/MS methods. Considering the simplicity and accessibility of this sample preparation and its robust results, this procedure could be easily proposed as a simple sample preparation approach to monitor microplastics by mass-based methods. T2 - MICRO 2024 CY - Arrecife, Spain DA - 23.09.2024 KW - Microplastics KW - Milk KW - Polymer 3R KW - TED-GC/MS PY - 2024 AN - OPUS4-61273 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Round Table for Expert Stakeholders​ - The Transfer of Research into Policy and Regulation N2 - This talk gives an overwiew about the material and physico chemical characterisation of materials developed for the EU founded project PlasticsFate. Particles in 1st and 2nd sample set are presented next to their characterisatin and documentation in data sheets. Some materials are prepared for reference material and used in an interlaboratory comparison. Results are briefly discussed. T2 - Stakeholder Workshop PlasticsFate CY - Bühl, Germany DA - 17.09.2024 KW - Microplastics KW - Reference materials KW - Polymer 3R KW - Interlaboratory comparison PY - 2024 AN - OPUS4-61088 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Alić Stolar, Jasna T1 - Harnessing mechanochemistry to tackle PFAS pollution N2 - We are currently facing one of the most serious environmental crises in human history – the widespread pollution caused by PFAS. PFAS stands for per- and polyfluoroalkyl substances, which are toxic, persistent, highly mobile, and bioaccumulative compounds, often referred to as 'forever chemicals'. For over 70 years, they have been used to make products resistant to water, heat, and stains, but the cost of damaging ecosystems and harming human health was revealed far too late. As of 2023, there were more than 23,000 confirmed PFAS contamination sites in Europe alone, with at least an equal number of presumptive contamination sites due to historical and current industrial activities.1 Public concern has pushed regulatory bodies to restrict the production of the most common PFAS, but with over 10,000 PFAS compounds and existing contamination, the problem remains largely unresolved. State-of-the-art remediation strategies rely on energy-intensive incineration, which releases greenhouse gases and smaller, volatile PFAS derivatives.2 Here, we present a fast, simple, and sustainable method for the complete degradation of PFAS, leveraging mechanochemistry3 to break down the persistent carbon-fluorine bonds. Our findings indicate that liquid-assisted grinding conditions accelerate the degradation of perfluorooctanoic acid compared to neat grinding conditions, resulting in a significant reduction in energy consumption. Moreover, the fluoride released during the process binds to inorganic additives, allowing fluorine recovery as crystalline salts and preventing the formation of secondary toxic waste. The method has strong potential for scaling up and offers a green and viable solution for real-world application in PFAS decontamination. T2 - Tag der Chemie CY - Berlin, Germany DA - 03.07.2025 KW - Mechanochemistry KW - Forever chemicals KW - Sustainability PY - 2025 AN - OPUS4-63972 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Bauer, J. A1 - Miclea, P.-T. A1 - Braun, U. A1 - Altmann, Korinna A1 - Turek, M. A1 - Hagendorf, C. T1 - Microplastic detection and analysis in water samples N2 - Microplastic detection in water samples becomes important for tracing microplastic sources. Microplastic may harm desalination facilities by blocking filters and disturbing the marine food chain. Thermo analytical methods such as pyrolysis gas chromatography mass spectroscopy, and spectroscopic methods like (micro) Raman spectroscopy or (micro) Fouriertransform infrared spectroscopy in combination with appropriate filters and sample preparation are suitable for analyzing microplastics on a scale from 1 µm to 1000 µm fast and unambiguous. While the thermo analytical methods are suitable for larger sample volumes, Raman spectroscopy and Fouriertransform infrared spectroscopy are able to detect and analyze single microplastic particles for instance in bottled water. Machine learning algorithms ensure a reliable classification of different plastic materials. T2 - International Conference on Sustainable Energy-Water-Environment Nexus in Desert Climate 2019 CY - Ar-Rayyan, Qatar DA - 02.12.2019 KW - Microplastics KW - Water samples PY - 2022 SP - 111 EP - 113 PB - Springer AN - OPUS4-56240 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Müller, Axel T1 - Representative sampling of roadside soil and determination of tire wear contents by TED-GC/MS N2 - The presentation describes microplastic findings from tyre wear near roads. Both the sampling and the analysis are presented. T2 - Mikroplastik Workshop der Hochschule Zittau CY - Online meeting DA - 25.11.2021 KW - Mikroplastik KW - Reifenabrieb KW - TED-GC/MS KW - Probennahme PY - 2021 AN - OPUS4-53831 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Dittmann, Daniel A1 - Saal, L. A1 - Zietzschmann, F. A1 - Mai, M. A1 - Altmann, Korinna A1 - Al-Sabbagh, Dominik A1 - Ruhl, A. S. A1 - Jekel, M. A1 - Braun, U. T1 - Aktivkohlecharakterisierung als weiterer Schlüssel für Adsorptionsprognosen organischer Spurenstoffe in der vierten Reinigungsstufe N2 - In diesem Beitrag wird der Einfluss des Aktivkohleprodukts auf die Adsorption von Spurenstoffen aus Kläranlagenablauf gezeigt und diskutiert. Im zweiten Teil wird das Material Aktivkohle analytisch charakterisiert und die Eigenschaften systematisiert. Die gewonnenen Erkenntnisse werden mit Bezug zu Praxislösungen zusammengefasst. T2 - Wasser 2021 CY - Online meeting DA - 10.05.2021 KW - Aktivkohle KW - Thermogravimetrie KW - Zersetzungsgasanalyse KW - Proximatanalyse PY - 2021 SP - 373 EP - 378 AN - OPUS4-52740 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wiesner, Yosri T1 - MIKROPLASTIK – von der Probenvorbereitung bis zur Analytik N2 - Der Vortrag beschreibt die Herausforderungen bei der Analyse von Mikroplastik inklusive Probennahme, Probenvorbereitung und Detektion. Es werden Ergebnisse aus dem BMBF-Projekt RUSEKU vorgestellt. T2 - LABO-Anwendertag CY - Online meeting DA - 23.11.2021 KW - Mikroplastik KW - TED-GC/MS KW - Mikroplastik-Analytik PY - 2021 AN - OPUS4-53829 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Mikroplastik – Ein Problem für die Menschheit? N2 - Mikroplastik findet sich in Ozeanen, Seen, Flüssen und Bächen. Es kann in unserem Boden, in der Luft und sogar in Organismen nachgewiesen werden. Jedes Jahr werden weltweit Millionen Tonnen freigesetzt. Doch wo und wie landet Mikroplastik in der Umwelt? Und wie können wir diese winzigen Partikel nachweisen? T2 - Berlin Science Week CY - Berlin, Germany DA - 01.11.2021 KW - Mikroplastik KW - TED-GC/MS PY - 2021 AN - OPUS4-53734 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Mikroplastik Referenzmaterial und erste Vergleichsuntersuchungen N2 - Hierbei geht es um die Vorstellung von ersten Möglichkeiten um Referenzmaterial für die Mikroplastik-Analytik herzustellen und die Ergebnisse erster Vergleichsversuche. T2 - EUROLAB-D Workshop: Mikroplastik in der Praxis CY - Online meeting DA - 30.11.2021 KW - Mikroplastik KW - Referenzmaterial KW - Vergleichsversuche PY - 2021 AN - OPUS4-53880 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Microplastics at BAM: TED-GC/MS and reference materials N2 - Thsi talk aims to present the activities of microplastic analysis at BAM according to TED-GC/MS and reference materials developement. T2 - Webinar BAM / University of Birmingham CY - Online meeting DA - 15.06.2021 KW - Microplastic KW - TED-GC/MS KW - Reference materials PY - 2021 AN - OPUS4-53738 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Meurer, Maren T1 - Optimierung der Mikroplastik Analytik mittels TED-GC/MS sowie Reduktion von falsch positiven PE Werten durch beschleunigtes Lösemittelverfahren N2 - Ein drastisch hoher Polyethylene Massenanteil wurde bei der Analytik der Umweltproben im Vergleich zu weiteren Polymeren festgestellt. Zu einem Überbefund des Polyethylene können strukturell verwandte Verbindungen wie z.B. Fette durch Signalüberlagerung führen. Mithilfe von beschleunigter Lösemittelextraktion soll die störende Komponente entfernt werden. T2 - Die Wasser 2021 CY - Online meeting DA - 10.05.2021 KW - Extraktion KW - Mikroplastik KW - ASE KW - Polyethylene PY - 2021 AN - OPUS4-53896 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Brirmi, M A1 - Chabbah, T. A1 - Chatti, S. A1 - Schiets, F. A1 - Casabianca, H. A1 - Marestin, C. A1 - Mercier, R. A1 - Weidner, Steffen A1 - Errachid, A. A1 - Jaffrezic-Renault, N. A1 - Ben Romdhane, H. T1 - Effect of the pendent groups on biobased polymers, obtained from click chemistry suitable, for the adsorption of organic pollutants from water N2 - In this work, four triazole-based poly(ether-pyridine)s polymers were synthesized and used as an adsorbent for the removal of phenolic compounds from aqueous solutions. For this purpose, new fluoromonomers containing 1,2,3-triazole units were prepared by the Cu(I)-catalyzed 1,3-dipolar cycloaddition reaction and then used for the elaboration of novel poly(ether-pyridine-triazole)s (PEPTs) by direct polyconden-sation with isosorbide and bisphenol A. Chemical structure of fluorinated pyridinicmonomers as well as resulting polymers was confirmed by 1H and 19F NMR spectroscopic methods. The thermal behavior of the obtained PEPTs was characterized using differential scanning calorimetry and thermogravimetric analysis. Results of sorption showed that polymers can be effectively used as a sorbent for the removal of polarorganic pollutants. The isosorbide-based poly(ether-pyridine-triazole) which contains hydrophilic hydroxyl groups as pendants chains (P4) exhibited the highest sorption efficiencies (78%–100% after 1 h). In order to explain the results an adsorption mech-anism mainly based on π–π interactions and hydrogen bonding with the pendent groups is proposed. KW - Adsorption KW - Biobased polymers KW - Cycloaddition KW - Pentafluoropyridine KW - Phenolic compounds PY - 2022 DO - https://doi.org/10.1002/pat.5809 SN - 1042-7147 SP - 1 EP - 21 PB - Wiley online library AN - OPUS4-55389 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Jlalia, I. A1 - Gomri, M. A1 - Chabbah, T. A1 - Chatti, S. A1 - Weidner, Steffen A1 - Abderrazak, H. A1 - Marestin, C. A1 - Mercier, R. A1 - Ben Halima, H. A1 - Lakard, B. A1 - Jaffrezic Renault, N. T1 - Design of Fluorinated Poly(Ether-Pyridine) Films for Impedimetric Detection of Heavy Metal Ions N2 - A series of fluorinated poly(ether-pyridine)s were synthesized via polycondensation of bis-perfluoropyridine with either bisphe-nol A (BPA) or isosorbide, a bio-sourced diol. The polymers were characterized using 1 H and 19 F NMR spectroscopy, and their molecular weights were determined using GPC. Thermal properties were assessed using thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The presence of isosorbide in polymer P2 increases the glass transition temperature and results in a lower molecular weight and a higher hydrophilicity. On the other hand, polymer P3, based on BPA, shows the best thermal stability, the highest molecular weight, and the most pronounced hydrophobic character. Electrochemical impedance spectroscopy (EIS) was used to evaluate the modified gold electrodes for the selective detection of metal ions. Among the four target ions (Ni 2+, Cd 2+, Pb2+, and Hg 2+), defined by the European Water Framework Directive, Pb2+ was selectively detected on the hydrophilic polymer P2, while Cd 2+ was selectively detected on the hydrophobic polymer P3. The achieved detection limits were 5 × 10−11 M, corresponding to 10 ng/L for Pb2+ and 5.6 ng/L for Cd 2+, respectively. KW - Cadmium KW - Electrochemical impedance spectroscopy KW - Fluorinated polyether pyridines KW - Isosorbide KW - Lead PY - 2025 DO - https://doi.org/10.1002/pat.70038 SN - 1099-1581 VL - 36 IS - 1 SP - 1 EP - 14 PB - John Wiley & Sons Ltd. AN - OPUS4-62384 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Yu, Jialu T1 - Simultaneous In Situ Fe Isotope and Trace Element Analysis by LASS-MC-ICPMS / ICP-ToF-MS: Validation and Applications N2 - Iron isotopes serve as sensitive tracers of iron’s origin, transformations, and cycling in the natural system. Their sensitivity to redox changes, biological processing, and mineral–fluid interactions makes them a valuable indicators in both geochemical and biological studies. To obtain Fe isotope ratios together with trace elemental information from the same ablation volume, a laser-ablation split-stream (LASS) configuration was employed:. The laser system was coupled simultaneously to a multi-collector ICP-MS (MC-ICP-MS) and an inductively coupled plasma time-of-flight mass spectrometer (ICP-ToF-MS). The ablated aerosol is divided into two gas streams which enable for a high-precision Fe isotope measurements on the MC-ICP-MS while acquiring full quantitative multi-element datasets on ICP-ToF-MS. The performance of this approach was assessed validated using in-house gelatin reference materials and two well-characterized basaltic glass standards, BHVO-2G and BCR-2G. These materials were prepared and analysed to determine the accuracy and precision of the LASS setup. The obtained Fe isotope ratios and elemental concentrations were in a good agreement with established/published values, indicating that the method provides reliable isotope measurements alongside robust, quantitative elemental data. Following validation, the LASS technique was applied to a series of materials representing different scientific domains: the biological reference material NIST 1577c (bovine liver) and two iron-oxide materials: hematite (HMIE-NP-B01) and magnetite (MARK-NP-B01). The successful application of the method to these contrasting materials highlights the flexibility and analytical ability of the LASS approach for Fe isotope ratio measurement and elemental fingerprint in diverse geological and biological contexts. T2 - DGMS ICP-MS user meeting 2026 CY - Leipzig, Germany DA - 10.03.2026 KW - Fe isotope KW - Laser ablation KW - Geological materials KW - Split stream KW - Gelatin KW - ICP-ToF-MS KW - Elemental fingerprint PY - 2026 AN - OPUS4-65677 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Sanchez-Olivares, Guadalupe A1 - Brehme, Sven A1 - Calderas, F. A1 - Schartel, Bernhard T1 - Flame Retardant Polyolefins Using Fibers From Leather Waste: Adjusting Extrusion Variables to Balance the Property Profile N2 - The extrusion processing variables represent a key to the optimal use of additives and thus the development of flame-retardant polymer composites. Adjusting the property profile, for example, finding a balance between flame retardancy and mechanical properties is the main challenge. In this work, the effect of blending temperature and rotational speed on physico-mechanical properties and fire behavior of polyolefin composites was investigated. High-density polyethylene or polypropylene was used as polymer matrices; the polymers were compounded by the extrusion process using industrial-waste leather fibers as flame retardant adjuvant and commercial flame-retardant additives. A detailed rheological analysis highlighted different viscoelastic behavior, that is, a predominant elastic or viscous one. The effect of the extrusion processing variables was also investigated on the morphology, mechanical properties, thermal decomposition, fire behavior under forced flaming combustion and flammability. Important improvements were revealed with respect to using only high loading of flame retardants. For high-density polyethylene-based composites, impact resistance and elongation at break increased 8 and 7.5 times, respectively. The total heat evolved (87MJ/m2), effective heat of combustion (31.6MJ/kg), flame retardancy (UL 94 rating) results were comparable with the reference sample. Meanwhile for polypropylene composites, the impact resistance increased 2.2 times and the flame retardancy was improved from no rating in the UL 94 vertical test to V-0 rating. Tailored processing was highlighted as an autonomous and powerful approach to achieve balanced and demanding properties. KW - Biomaterials KW - Composites KW - Extrusion KW - Flame retardance KW - Leather waste KW - Polyolefins PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-656732 DO - https://doi.org/10.1002/vnl.70048 SN - 1548-0585 SN - 1083-5601 VL - 32 IS - 2 SP - 410 EP - 430 PB - Wiley Periodicals LLC. AN - OPUS4-65673 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Scharek, Vera M. A1 - Traub, Heike A1 - Meermann, Björn T1 - A direct solid sampling approach for fluorine determination via ETV/ICP-QQQ-MS N2 - Organic fluorine sum parameters are used to detect F-containing pollutants, e.g., per- and polyfluoroalkyl substances (PFASs), in the environment, within materials, or for monitoring technical processess, e.g., thermal decomposition of PFAS during municipal waste incineration. However, established approaches determining the extractable organic and adsorbable organic fluorine content (EOC and AOC) require laborious and error-prone sample preparation. We report a solid sampling-electrothermal vaporization (ETV) method for direct fluorine measurement based on the formation of [138Ba19F]+ with an inductively coupled plasma-triple quadrupole-mass spectrometer (ICP-QQQ-MS). Method development involved the instrumental setup for Ba introduction and fluorine-specific tuning of lens and collision-reaction cell (CRC) parameters. An inorganic fluorine fraction was detected in a cyclonic dust sample from a municipal waste incineration plant as a peak above a broad background signal. The content was estimated through standard addition using a NaF solution to 2300 mgg−1. With a limit of detection (LOD) of 130 mg g−1, which was below the reported value for an electrothermal vaporization/inductively coupled plasma-mass spectrometry (ETV/ICP-MS) approach, acquiring [19F]+. The method's potential for fractionation analysis was demonstrated by analyzing polytetrafluoroethylene (PTFE) powder. KW - PFAS KW - ETV/ICP-QQQ-MS KW - Solid sampling PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-656766 DO - https://doi.org/10.1039/d6ja00014b SN - 0267-9477 SP - 1 EP - 7 PB - Royal Society of Chemistry (RSC) AN - OPUS4-65676 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Aktuelles aus dem BAM-Fachbeirat N2 - Die Anforderungen an Geokunststoffprodukte und deren Qualitätssicherung unterliegen einem stetigen Wandel, der sowohl durch technische Veränderungen als auch durch normative und organisatorische Entwicklungen geprägt ist. Insbesondere der Fachbeirat der BAM gemäß Deponieverordnung (DepV) spielt hier im Bereich der Deponietechnik eine wichtige Rolle. An dieser Stelle sollen aktuelle Themen aus dem Fachbeirat der BAM vorgestellt werden, die wesentliche Änderungen in der Zulassungs- und Anwendungspraxis betreffen. Der Beitrag beleuchtet unter anderem Veränderungen innerhalb der BAM, die Modernisierung der Publikationsformate sowie die fachliche Weiterentwicklung der Zulassungsrichtlinien. T2 - 22. Leipziger Deponiefachtagung CY - Leipzig, Germany DA - 10.03.2026 KW - Deponie KW - Geotextil KW - Abdichtungssystem PY - 2026 SN - 978-3-00-085899-4 VL - 22 SP - 15 EP - 22 PB - HWTK Leipzig CY - Leipzig AN - OPUS4-65664 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Roß, Marcel A1 - Severin, Stefanie A1 - Hildebrandt, Jana A1 - Erdmann, Kerstin A1 - Miaskiewicz, Aleksandra A1 - Škorjanc, Viktor A1 - Bernardes de Araujo, Wander Max A1 - Leyden, Matthew A1 - Korte, Lars A1 - Seeger, Stefan A1 - Dallmann, André A1 - Albrecht, Steve T1 - Compositional Analysis of Metal Halide Perovskites: Insight into the Coevaporation Process via Nuclear Magnetic Resonance and X-ray Fluorescence Spectroscopy N2 - Lead halide perovskites have emerged as a highly promising class of materials for solar cells. Nevertheless, suitable procedures to analyze the exact composition of the perovskite films are rare and are not generally applicable. Here we show a simple and fast method to determine the absolute composition of mixed metal halide perovskites through a combination of nuclear magnetic resonance and total reflection X-ray fluorescence spectroscopy. The method is validated on powder mixtures and applied to thin film samples prepared by coevaporation of formamidinium iodide (FAI), CsI, PbI2 and PbBr2, allowing correlation between film composition and solar cell performance. We show that the rates of the individual precursors do not always translate linearly into film composition and that the preparation of the hole transport layer MeO-2PACz strongly influences the incorporation of FAI. Our work highlights the importance of compositional analysis and demonstrates how the developed method provides new insights into the complex coevaporation process in perovskite solar cells. KW - e‑ray Fluorescence Spectroscopy KW - Metal Halide Perovskites KW - CoevaporationP rocess KW - Nuclear Magnetic Resonance PY - 2026 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-656932 DO - https://doi.org/10.1021/acsenergylett.5c03689 SN - 2380-8195 VL - 11 IS - 2 SP - 1935 EP - 1943 PB - American Chemical Society (ACS) AN - OPUS4-65693 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Bijeljic, Jelena A1 - Niederleithinger, Ernst T1 - Concrete performance assessment based on gas permeability testing N2 - Designing of structures with medium to high performance requirements is a demanding and challenging engineering task. Depending on the location and type of the planned structure, various pre-testing methods should be applied. In recent decades, there has been a focus on the durability of concrete. Concrete is a porous material with a relatively thin protective cover layer, making it vulnerable to the penetration of external agents such as carbon dioxide. Gas permeability testing (kT), a relatively new non-destructive method (NDT), should therefore be considered. This paper presents results of gas permeability testing on a set of larger concrete samples made under controlled conditions with some paroperty variations order to find initial kT parameters important for quality assurance. KW - Concrete KW - Permeability KW - Durability KW - Torrent Tester PY - 2025 DO - https://doi.org/10.62683/ZRGAF41.2 SN - 3009-4674 VL - 41 IS - 1 SP - 15 EP - 23 PB - Faculty of Civil Engineering and Architecture, University of Nis AN - OPUS4-65715 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Altmann, Korinna A1 - Abusafia, A A1 - Bannick, C-G A1 - Braun, U A1 - Crasselt, Claudia A1 - Dittmar, S A1 - Fuchs, M A1 - Gehde, M A1 - Hagendorf, C A1 - Heller, C A1 - Herper, D A1 - Heymann, S A1 - Kerndorff, A A1 - Knefel, M A1 - Jekel, M A1 - Lelonek, M A1 - Lunkenbein, T A1 - Obermaier, N A1 - Manhart, M A1 - Meurer, Maren A1 - Miclea, P-T A1 - Paul, A A1 - Richter, S A1 - Ricking, M A1 - Rohner, C A1 - Ruhl, A A1 - Sakai, Y A1 - Saravia Arzabe, C A1 - Scheid, C A1 - Schmitt, M A1 - Schnarr, M A1 - Schwertfirm, F A1 - Steinmetz, H A1 - Wander, Lukas A1 - Wiesner, Yosri A1 - Zechmeister, L T1 - RUSEKU - Repräsentative Untersuchungsstrategien für ein integratives Systemverständnis von spezifischen Einträgen von Kunststoffen in die Umwelt : Abschlussbericht N2 - Im Verbundprojekt RUSEKU wurde die Probenahme von Wasserproben entscheidend weiterentwickelt. Wichtig ist hierbei zu gewährleisten, dass genügend Merkmalsträger in jeder Probe untersucht werden. Es muss daher eine für den Probenahmeort repräsentative Beprobung hinsichtlich des Wasservolumens in Abhängigkeit der Partikelanzahl gewährleistet sein. Das Hauptaugenmerk lag im vorliegenden Projekt auf einer praxisnahen Beprobungsstrategie. Es wurden verschiedene Konzepte ausprobiert. • Grundsätzlich hat sich gezeigt, dass eine Stichprobe eine Momentaufnahme des MP-Massengehaltes zeigt. Es wird eine hohe Statistik, also eine Vielzahl an Messungen am gleichen Probenahmeort, benötigt, um eine valide Aussage über den MP-Gehalt zu machen. • Es zeigt sich, dass eine integrale Probenahme über mehrere Wochen mit dem SK routinemäßig möglich ist. Die erfassten MP-Massen sind reproduzierbar und robust. • Die DFZ ist für Stichproben geeignet. Partikel < 50 µm werden eventuell unterschätzt • Die fraktionierte Filtration kann für Stich- und Mischproben direkt im Feld genutzt werden. Fraktionen von 10 und 5 µm werden später im Labor Vakuum filtriert. Es erfolgt eine Fraktionierung der Probe mit Siebmaschenweiten von 1000, 500, 100, 50, 10 und 5 µm. • Die fraktionierte Filtration kann auch anschließend an die Beprobung mit dem SK zur Anwendung kommen. Wird die mit dem SK gewonnene Wasserprobe fraktioniert filtriert, kann neben einem MP-Gesamtgehalt auch eine Einschätzung über die Partikelgrößen gewonnen werden. • Für Wässer mit geringen Partikelzahlen wurde ein Messfiltertiegel entwickelt. Dieser hat eine Maschenweite von 6 µm. Seine Anwendung kann mögliche Verluste beim Transferieren vom Probenahmetool zum Messgefäß und mögliche Kontaminationen reduzieren. Die Optimierung der Probenahmestrategie wurde durch Modellversuche und Simulationen unterstützt. Modellversuche zum Sinkverhalten und Simulationen von MP in realen Gewässern verdeutlichten das komplexe Verhalten der Partikel. Es konnte gezeigt werden, dass Partikel ab einer bestimmten Größe (und kleiner) bei genügend starker Turbulenz sich in der Wassersäule unabhängig von ihrer Dichte verhalten und so auch MP mit kleiner Dichte (z.B. PE) in der gesamten Wassersäule zu finden sind. Es konnte mit dem TEM die Existenz von NP gezeigt werden. Ein wesentlicher Aspekt des RUSEKU Projektes war die Beprobung realer Kompartimente. Beprobt wurde neben Oberflächengewässern, das urbane Abwassersystem der Stadt Kaiserslautern, Waschmaschinenabwasser und Flaschenwasser. • In Oberflächengewässern wurde hauptsächlich PE gefunden. Je nach Probe und Gewässer konnten auch PP, PS, PET, PA, SBR und Acrylate nachgewiesen werden. • Im urbanen Abwassersystem der Stadt Kaiserslautern konnte an allen Probenahmestandorten MP nachgewiesen werden. Es wurde hauptsächlich PE, neben geringeren Mengen an PP, PS und SBR gefunden. Nach einem Regenereignis war der SBR Anteil deutlich erhöht. • Die Beprobung eines realen Wäschepostens, bestehend aus T-Shirts und Hemden mit PA/CO oder PES/CO Mischgewebe, zeigte einen PA- und PES-Austrag im Waschwasser. Der überwiegende Teil der detektierten Fasern ist aber auf Baumwolle zurückzuführen. Reine gravimetrische Messungen zur Detektion von MP führen zu einer starken Überschätzung. • In Flaschenwasser (PET-Flaschen) konnte MP detektiert werden. PET wurde nur im stillen Mineralwasser, nicht in Mineralwasser mit Kohlensäure gefunden werden. Teilweise wurde auch das MP-Material des Verschlusses im Wasser detektiert. • Für Luftproben konnte ein Aufbau zur größenselektiven Beprobung getestet werden. Neben der Probenahme hat das Projekt auch gezeigt, dass die TED-GC/MS geeignet für die MP-Detektion im Routinebetrieb ist. Die TED-GC/MS konnte weiter optimiert werden. Es wurden MP-Massen bestimmt. Im Projekt wurden erste realitätsnahe Referenzmaterialien für die MP Detektion hergestellt. Die Herstellung von realitätsnahen Polymeren in ausreichender Homogenität und Menge hat sich als große Herausforderung herausgestellt. KW - Mikroplastik KW - Probennahme KW - TED-GC/MS KW - Fraktionierte Filtration KW - Mikroplastikreferenzmaterial PY - 2022 SP - 1 EP - 201 AN - OPUS4-57800 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Thünemann, Andreas T1 - Developtment of Nanoplastics Reference Materials at BAM N2 - Engineered particles are essential for sustainable innovation and modern industrial applications, but their reliable, number‑based characterisation remains a major challenge. Regulatory frameworks in healthcare, personal care (EU 745/2017, 749/2017, 1223/2009), and environmental monitoring—such as the EU Drinking Water Directive 21840/2020—demand robust particle measurements across complex matrices. Yet standardised methods currently exist only for simple particle systems, leaving significant gaps for technologically relevant materials and for micro‑ and nanoplastics as emerging pollutants. These challenges are amplified by the lack of well‑defined input parameters, particularly density and refractive index, which are critical for many analytical and modelling approaches. This talk highlights BAM’s work on developing nanoplastics reference materials to support validated, traceable, and harmonised measurement methods. I will outline strategies for producing stable, well‑characterised polymeric nanoparticles, establishing accurate material parameters, and integrating these reference materials into interlaboratory and standardisation activities. These efforts provide the metrological foundation urgently needed for regulatory testing, environmental monitoring, and industry innovation. T2 - ConcenSus Virtual Webinar on Reference Materials supporting characterization of nanomaterials: Current status and future trends CY - Online meeting DA - 17.03.2026 KW - Nanoplastics KW - Nanoparticle PY - 2026 AN - OPUS4-65717 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Rudolf T1 - Enhancing wastewater surveillance through anthropogenic markers N2 - Since the global COVID-19 pandemic, there has been an increased focus on systematically monitoring pathogens in raw wastewater - a practice known as wastewater-based epidemiology (WBE). This approach, aligned with the One Health concept, the revised EU Urban Wastewater Treatment Directive (2024), and Germany’s amended Infection Protection Act (2023), aims to generate health data independently of individual testing and reporting behaviors through wastewater surveillance. – Germany’s AMELAG project implemented wastewater surveillance at approximately 170 treatment plants, with biweekly sampling. This infrastructure - comprising treatment plants, logistics, laboratories, and health authorities - also provided us samples that were analyzed for their levels of a series of anthropogenic markers. These markers improve data accuracy by accounting for site-specific variations in wastewater composition and flow rates, such as those caused by stormwater runoff. Beyond epidemiology, wastewater surveillance provides valuable insights into the spread of antimicrobial resistance (AMR), drug consumption, industrial discharges, and the efficiency of wastewater treatment plants in eliminating indicator substances. To assess these factors, cost-effective, high-throughput methods such as ELISA (Enzyme-Linked Immunosorbent Assay) offer a practical solution. This study examines ELISA’s application in detecting diclofenac, carbamazepine, and bisphenol A in wastewater samples from various locations. T2 - Pacifichem 2025 CY - Honolulu, HI, USA DA - 15.12.2025 KW - Antibodies KW - Immunoassay KW - Pharmaceuticals PY - 2025 AN - OPUS4-65720 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Schneider, Rudolf T1 - Advancing environmental screening and monitoring: Immunoanalytical approaches for emerging contaminants N2 - Micropollutants, including various emerging contaminants, are continuously released into the environment. Detecting their presence using conventional analytical methods is often expensive and time-consuming, making large-scale monitoring impractical. To effectively protect ecosystems and human health, rapid and cost-efficient screening methods are essential. Furthermore, the need to monitor the entire water cycle for micropollutants is becoming increasingly critical, particularly from a One Health perspective, as climate change and growing demands for water reuse amplify environmental challenges. – Antibody-based methods, commonly referred to as immunoassays, offer a promising solution. These rapid and cost-effective techniques can fill information gaps and provide sensors and process analytical technology with short response times. A wide range of immunoanalytical formats is available, from laboratory-based methods to portable analyzers and online sensors. Ensuring the availability of high-quality antibodies is essential to the reliability of these approaches. This talk presents how a whole range of immunoanalytical methods can be employed to trace emerging contaminants in the environment. An indicator for specific industrial inputs is bisphenol A which is also an endocrine disruptor. Additionally, pharmaceuticals serve as important markers of human impact on the water cycle. Natural tracers, such as endogenous hormones and bile acids, help track wastewater pathways, while anthropogenic markers - most notably caffeine - serve as indicators of human activity, frequently appearing in environmental water samples. T2 - Pacifichem 2025 CY - Honolulu, HI, USA DA - 15.12.2025 KW - Antibodies KW - Immunoassay KW - Pharmaceuticals PY - 2025 AN - OPUS4-65719 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ryll, Tom William T1 - Multi-modal characterization for transformation of gypsum to anhydrite N2 - We investigate recycling of gypsum waste materials and have developed a method to synthesize phase pure anhydrite in solution, while contaminants could easily be separated from products. In-situ XRD measurements were conducted in a dedicated automation setup at BESSY II to find exact reaction conditions and were supported by in-situ Raman spectroscopy. T2 - Joint BAM-HZB Symposium on Multimodal Synchrotron Experiments for Next-Generation Materials Research CY - Berlin, Germany DA - 25.02.2026 KW - Recycling KW - Automation KW - Synchrotron XRD KW - Raman spectroscopy KW - Gypsum PY - 2026 AN - OPUS4-65607 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Chandna, Sanjam A1 - Povolotsky, Tatyana L. A1 - Nie, Chuanxiong A1 - Schwartz, Sophia A1 - Wedepohl, Stefanie A1 - Quaas, Elisa A1 - Ludwig, Kai A1 - Boyakova, Yulia A1 - Bhatia, Sumati A1 - Meyer, Klas A1 - Falkenhagen, Jana A1 - Haag, Rainer A1 - Block, Stephan T1 - Lignin-Based Mucus-Mimicking Antiviral Hydrogels with Enzyme Stability and Tunable Porosity N2 - Mucus is a complex hydrogel that acts as a defensive and protective barrier in various parts of the human body. Therise in the level of viral infections has underscored the importance of advancing research into mucus-mimicking hydrogels for theefficient design of antiviral agents. Herein, we demonstrate the gram-scale synthesis of biocompatible, lignin-based virus-bindinginhibitors that reduce waste and ensure long-term availability. The lignin-based inhibitors are equipped with sulfate moieties, whichare known binding partners for many viruses, including SARS-CoV-2 and herpes viruses. In addition, cross-linking the synthesizedinhibitors yielded hydrogels that mimicked native mucus concerning surface functionality and rheology. The degree of sulfationexhibits a very strong impact on the mesh size distribution of the hydrogels, which provides a new means to fine-tune the steric andelectrostatic contributions of the virus−hydrogel interaction. This feature strongly impacts the sequestration capability of the lignin-based hydrogels, which is demonstrated by infection inhibition assays involving human herpes simplex virus 1, influenza A viruses,and the bacterium Escherichia coli (E. coli). These measurements showed a reduction in plaque-forming units (HSV-1) and colony-forming units (E. coli) by more than 4 orders of magnitude, indicating the potent inhibition by the lignin-based hydrogels KW - Lignin functionalization KW - Mucus-mimicking hydrogels PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-625301 DO - https://doi.org/10.1021/acsami.4c18519 SP - 1 EP - 14 PB - American Chemical Society (ACS) CY - USA AN - OPUS4-62530 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Wagner, Jan A1 - Dudziak, Mateusz A1 - Falkenhagen, Jana A1 - Rockel, Daniel A1 - Reimann, H.-A A1 - Schartel, Bernhard T1 - This is the way: An evidence based route to phytic-acid–based flame retardant poly(lactide acid) N2 - A systematic sequence of materials was investigated to develop phytic-acid (Phyt)–based flame retarded poly (lactide acid) (PLA), while factoring in molecular weight (MW), crystallinity and mechanical properties. Synergistic approaches were developed based on combinations with lignin and expandable graphite (EG), as well as by applying different Phyt salts of melamine (Mel), piperazine (Pip), and arginine (Arg). Compounds were twin screw extruded, injection molded, hot pressed and investigated with thermal analysis, size exclusion chromatography, infrared spectroscopy, tensile testing, limited oxygen index (LOI), UL 94, cone calorimeter, and scanning electron microscope. 16.7 wt.% flame retardant (FR) slightly enhances crystallization while MW remains unchanged in PLA Phyt Arg and PLA Phyt Mel. LOI was improved to 43.7 vol.% for PLA Phyt Arg, UL 94 V0 achieved for PLA Phyt Pip. Cone calorimeter results show total heat evolved reduced by 14 %, maximum average rate of heat emission 43 % lower, and peak heat release rate reduced by 50 % for PLA Phyt Mel. Phyt Mel combined with EG increased the char yield of PLA to 20 wt.% and 15.5 wt.% at 600 and 900 ◦C, respectively. Phyt is exploited to enhance char yield, stabilize the intumescent char, and lower the apparent effective heat of combustion. The combination of Phyt Mel and EG was proposed as an efficient FR for PLA via an evidence based developing route. KW - Polylactide acid KW - Intumescent flame retardant KW - Phosphorous flame retardant KW - Phytic acid KW - Expandable graphite KW - Melamine PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-626395 DO - https://doi.org/10.1016/j.polymdegradstab.2025.111242 SN - 1873-2321 SN - 0141-3910 VL - 234 SP - 1 EP - 14 PB - Elsevier Ltd. AN - OPUS4-62639 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Geburtig, Anja A1 - Wachtendorf, Volker A1 - Falkenhagen, Jana T1 - Combined impact of UV radiation and nitric acid (HNO3) on HDPE jerrycans – comparison of outdoor and lab test N2 - A damaging action of HNO3-55% only occurs in combination with its decomposition into nitrous gases, which can be caused by UV radiation. In a laboratory test, transparent HDPE jerrycans have been exposed to both UV radiation and 55 wt-% nitric acid solution at (41 ± 2)°C, for up to 20 days. For comparison, UV radiant exposure (21 days) and nitric acid exposure (up to 6 weeks) were performed separately, at nearly equal temperatures. The respective damages are compared with FTIR spectroscopy in ATR and HT-gel permeation chromatography (GPC) on a molecular level and with hydraulic internal pressure testing as a component test. For the used jerrycans, relevant oxidation can only be found after the combined exposure. The gradual increase in oxidative damage shows the good reproducibility of the lab exposure. The decomposition of nitric acid into nitrous gases by UV radiation – as well as the jerrycan oxidation – is also observed at lower HNO3 concentration (28 wt- %). Similar results are obtained after outdoor tests. Again, the damage occurs only after combined exposure, in contrast to the exposures to UV only and to HNO3 only, which were conducted in parallel. Outdoor exposures are most readily accepted as they represent possible end-use conditions. However, the reproducibility of these exposures is poor due to the large temporal variations in weather. There are also several safety risks, which is why the number of replicates remains limited. Since the outdoor and lab exposure tests show the same qualitative results, it is appropriate to conduct systematic studies in the laboratory. After 6 days of lab exposure, the oxidation damage is rated as critical, which corresponds to about 1/10 year in Central Europe, according to the UV radiant exposure. It should be noted that this amount can also occur in two sunny weeks. T2 - 24th iapri World Packaging Conference CY - Valencia, Spain DA - 17.06.2024 KW - Ppolyethylene KW - UV exposure KW - Nitric acid KW - Oxidation PY - 2024 VL - 2 SP - 30 EP - 37 PB - ITENE AN - OPUS4-60414 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Falkenhagen, Jana T1 - 70 years size exclusion chromatography - An ongoing challenge N2 - The reason for our current activities is that polymers may also be subject to REACh regulations in the future. In this context, the determination of oligomer content is important. SEC is still the method of choice for determining molar mass distribution. The regulations aim for narrow limits and SEC has rather large error margins, which are well known to all experts. Different polymers need different methods. What to do when samples with a wide range of practical aspects, samples with higher distribution range, reduced solubility, including side components, gel content etc. need be analyzed? A concept for round robin tests and first impressions will be presented. T2 - Analytical Solutions 2025 CY - Ede, Netherlands DA - 04.06.2025 KW - Polymers KW - Size exclusion chromatography KW - REACH KW - Round Robin Tests PY - 2025 AN - OPUS4-63310 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Falkenhagen, Jana T1 - Challenges of sec and the necessity of round robin tests N2 - Size exclusion chromatography (SEC) is still the method of choice for determining the molar mass and molar mass distribution of macromolecules. From the distribution curve molar mass averages and the oligomer content (percentage of peak area smaller than 1000 g/mol and 500 g/mol) of polymers can be derived. The determination of oligomer content is important, because it is often used in regulatory contexts as a measure of small, mobile and potentially more toxic parts of the polymer. Polymer regulations are of increasing political and societal importance. Regulations often strive for narrow limits. But SEC has rather large error margins of 10-20% for the molar mass determination performed in different laboratories or on different instruments. These variances are well known to all experts and users and have been investigated in several round robin tests in the past. These resulted in DIN and ISO standards which, in our opinion, no longer meet today's requirements. Gaps have been identified that require further harmonization. Different polymer types or classes require different methods. On the other hand, as far as we know, the margins of error in determining oligomer content have not yet been investigated. It is expected that the variation will be rather high. This is because it depends on many factors related to the experimental conditions (column sets used, solvent, temperatures, sample preparation) on the one hand, and the data evaluation mechanisms (choice of baseline and peak limits) on the other. In order to actually measure the error margins and to support this with actual data a round robin test has been performed from June to November 2024 with approx. 40 participating laboratories. Three different solvents were selected, namely THF, DMAc or DMF and water. The samples were selected taking into account a wide range of practical aspects far from narrowly distributed standards: e.g higher distribution range, reduced solubility, included side components, copolymers and dispersions with gel content. In this contribution we will present the detailed concept of this round robin test and impressions T2 - 2025 Polymer Separations GNT meeting, Dow CY - Online meeting DA - 25.02.2025 KW - Polymers KW - Size exclusion chromatography KW - REACH PY - 2025 AN - OPUS4-63314 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Falkenhagen, Jana A1 - Fink, Friedrich T1 - Biobased and biodegradable polymers - sustainability and circular economy N2 - The presentation shows recent results on the synthesis and modification of environmentally relevant polymers based on renewable resources and the associated development of robust, high quality analytical methods. The first topic presents analytical results for star-shaped polylactides with different degrees of functionalisation. It is shown how liquid chromatography and mass spectrometry methods complement each other in a proven way to obtain accurate molar masses and to quantify chemically heterogeneous species. The second part presents an approach to incorporate lignin into epoxy matrices to obtain covalently adaptable epoxy networks that can be reprocessed and reused. T2 - 11th International Symposium on the Separation and Characterization of Natural and Synthetic Macromolecules CY - Amsterdam, Netherlands DA - 21.01.2025 KW - Polylactides KW - Ligninbased thermosets KW - MALDI-TOF-MS KW - Gradient elution liquid adsorption chromatography KW - Atomic force spectroscopy KW - FT-IR PY - 2025 AN - OPUS4-62532 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - RPRT A1 - Altmann, Korinna T1 - Deliverable 2: Summary report on: The development of pristine SI traceable reference materials for SMPs (0.1 μm - 10 μm) and NPs (< 0.1 μm), representative of partially degraded/naturally aged samples in complex food and environmental matrices, and for realistic polydisperse size distributions and irregular shapes N2 - PlasticTrace aims to address the urgent need for development and harmonisation of methods for the chemical identification, physical characterisation and quantification of released small micro/nanoplastics (SMPs/NPs) in drinking water, food and environmental matrices, as required by the EU’s Circular Economy Action Plan (CEAP). This report describs the characterisation of nanoPP analysed in the PlasticTrace project aiming to develop a reference material. The nanoPP was analysed mainly by light scattering methods. Homogeneity control was done by DLS. KW - Nanoplastics KW - Reference materials PY - 2024 N1 - Project Number 21GRD07: PlasticTrace (Tracing Micro and NanoPlastics in Food and Environment), funded by the European Union SP - 1 EP - 29 PB - European Association of National Metrology Institutes (EURAMET) CY - Braunschweig AN - OPUS4-62299 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Alić Stolar, Jasna T1 - Harnessing Mechanochemistry to Combat PFAS Contamination N2 - For over 70 years, the uncontrolled production, use, and disposal of per- and polyfluoroalkyl substances (PFAS) have led to widespread global contamination, necessitating the rapid development of innovative and efficient remediation technologies. State-of-the-art strategies rely on energy-intensive incineration, which releases greenhouse gases and smaller, volatile PFAS derivatives. Here, we present a fast, simple, and sustainable method for the complete degradation of PFAS leveraging mechanochemistry to break down the persistent carbon-fluorine bonds. Our findings indicate that liquid-assisted grinding conditions accelerate the degradation of perfluorooctanoic acid compared to neat grinding conditions, resulting in a significant reduction in energy consumption. Moreover, the fluoride released during the process binds to inorganic additives, allowing fluorine recovery as crystalline salts and preventing the formation of secondary toxic waste. The method has strong potential for scaling up and offers a green and viable solution for real-world application in PFAS decontamination. T2 - International Conference on Sustainable Chemistry for Net Zero (ICSC-NZ) CY - St. Andrews, Scotland DA - 10.06.2025 KW - Mechanochemistry KW - PFAS KW - Remediation PY - 2025 AN - OPUS4-63971 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Reference material candidates for microplastic analysis N2 - Every day, there are new headlines in the media about microplastics (1-1000 µm, ISO/TR 21960:2020) and nanoplastics (< 1 µm, ISO/TR 21960:2020) findings all over the planet with high variations in particle number and mass. The challenges in analytics are very complex, e.g. representative sampling, non-destructive sample preparation with concentrated particles and homogeneous distribution and true detection. All together lead to lacks in harmonization and results, which are hardly comparable. On the other hand, monitoring of microplastics is mandatory in the future strictly regulated by the EU commission in the Drinking water and Wastewater Framework Directive. One step to accurate and precise results will be the development of suitable reference materials mimicking particles in the environment. BAM developed test materials, which are produced by mixing a small portion of microplastic particles with a water-soluble matrix. After solid phase dilution and homogenisation small portions are pressed into tablets and bottled in glass vials (Figure 1). These tablets are well characterized with particle size distribution and SEM images. Additionally, they are tested as reference material candidate according to homogeneity and stability for particle number with µ-IR and µ-Raman as well as on particle mass with Py-GC/MS and TED-GC/MS after ISO Guide 35. Results are promising. The material passed the homogeneity control. No changes are observed within 6 months of storage. The same tested reference material is finally used in sample preparation experiments, where environmental suspended particular matter from surface water or baby milk powders are spiked with the tablets. T2 - ESOPS CY - Berlin, Germany DA - 09.09.2024 KW - Microplastics KW - TED-GC/MS KW - Reference materials KW - Polymer 3R KW - Tablets PY - 2024 AN - OPUS4-61017 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Altmann, Korinna T1 - Challenges in microplastics standardisation N2 - This talk addresses the challanges in microplastic analytics. It shows the need of standards, analytics and reference materials for accurate and reliable measurements. It explains the state of the art for referenence materials in this field and their problems. A solution is presented with PET tablets. The urgent need of harmonisation it also emphasised. T2 - MARII Summit CY - Madrid, Spain DA - 15.10.2025 KW - Microplastics KW - Reference materials PY - 2025 AN - OPUS4-64488 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Alić Stolar, Jasna T1 - Harnessing mechanochemistry to combat PFAS contamination N2 - For over 70 years, the uncontrolled production, use, and disposal of per- and polyfluoroalkyl substances (PFAS) have led to widespread global contamination, necessitating the rapid development of innovative and efficient remediation technologies. State-of-the-art strategies rely on energy-intensive incineration, which releases greenhouse gases and smaller, volatile PFAS derivatives. Here, we present a fast, simple, and sustainable method for the complete degradation of PFAS leveraging mechanochemistry to break down the persistent carbon-fluorine bonds. Our findings indicate that liquid-assisted grinding conditions accelerate the degradation of perfluorooctanoic acid compared to neat grinding conditions, resulting in a significant reduction in energy consumption. Moreover, the fluoride released during the process binds to inorganic additives, allowing fluorine recovery as crystalline salts and preventing the formation of secondary toxic waste. The method has strong potential for scaling up and offers a green and viable solution for real-world application in PFAS decontamination. T2 - International Conference on Sustainable Chemistry for Net Zero (ICSC-NZ) CY - St. Andrews, Scotland DA - 10.06.2025 KW - Mechanochemistry KW - PFAS KW - Remediation PY - 2025 AN - OPUS4-63970 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Alić Stolar, Jasna T1 - Harnessing mechanochemistry to combat PFAS contamination N2 - For over 70 years, the uncontrolled production, use, and disposal of per- and polyfluoroalkyl substances (PFAS) have led to widespread global contamination, necessitating the rapid development of innovative and efficient remediation technologies. State-of-the-art strategies rely on energy-intensive incineration, which releases greenhouse gases and smaller, volatile PFAS derivatives. Here, we present a fast, simple, and sustainable method for the complete degradation of PFAS leveraging mechanochemistry to break down the persistent carbon-fluorine bonds. Our findings indicate that liquid-assisted grinding conditions accelerate the degradation of perfluorooctanoic acid compared to neat grinding conditions, resulting in a significant reduction in energy consumption. Moreover, the fluoride released during the process binds to inorganic additives, allowing fluorine recovery as crystalline salts and preventing the formation of secondary toxic waste. The method has strong potential for scaling up and offers a green and viable solution for real-world application in PFAS decontamination. T2 - The International Symposium on Mechanochemistry (Mech’cheM 2025) CY - Montpellier, France DA - 04.06.2025 KW - Mechanochemistry KW - PFAS PY - 2025 AN - OPUS4-63956 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Ryll, Tom William T1 - In-situ analysis of nucleation processes – case study: calciumsulfate N2 - In this project we investigate nucleation pathways by utilizing synchrotron-XRD and running a case-study on calcium sulfate and its polymorphs. To accomplish this, we developed a modular automation setup for reactions in solution to run synthesis and control reaction conditions. So far we successfully characterized the recycling process of gypsum (CaSO4*2H2O) and are now investigating the formation of anhydrite (CaSO4*0H2O) as well as possible applications for the automation setup and analysis. T2 - SALSA Make & Measure 2025 CY - Berlin, Germany DA - 10.09.2025 KW - Recycling KW - Gypsum KW - Synchrotron-X-ray-diffraction KW - Raman-spectroscopy KW - Automation PY - 2025 AN - OPUS4-64135 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Sieg, Holger A1 - Heilscher, Jasmin A1 - Ott, Franziska A1 - Böhmert, Linda A1 - Drusch, Stephan A1 - Thünemann, Andreas A1 - Rohn, Sascha A1 - Braeuning, Albert A1 - Kieserling, Helena T1 - Direct Interactions of Micro- and Nanoplastics with Proteins – A Key to Mechanistic Understanding? N2 - Micro-/Nanoplastics (MNP) have gained widespread scientific and public attention within the last two decades. While knowledge about measuring techniques, occurrence and exposure was improved substantially, questions on toxicological impact of MNP remained unclear. A major reason for that are the continued remaining knowledge gaps with regard to mechanistical understanding of MNP effects. Our work aimed at investigating MNP properties, protein interactions, and cellular effects in combination. Therefore, we characterized MNP-protein- adsorption, changes in protein structure, cellular uptake and cellular modes of action. In a first study, we studied the molecular interactions of β-lactoglobulin, a serum and storage protein, with different MNP materials1. We identified structural changes, depending on physicochemical MNP properties, using FTIR- and fluorescence spectroscopy. Furthermore, we investigated cellular uptake of MNP individually and as a complex with β-lactoglobulin and studied the effects on cell growth and viability, using colorimetric MTT testing, flow cytometry, and cell impedance measurements. MNP material properties, especially hydrophobicity, had an impact on protein folding and consequently also on cellular interactions. In a second study, we applied α-amylase, an extracellular digestive protein with enzymatic activity. Here, in addition, we investigated the influence of MNP binding on enzyme activity, using a colorimetric starch degradation assay. We observed for the most MNP, that adsorption processes resulted in a decrease of enzyme activity. Furthermore, we used Alexa633 staining to visualize MNP uptake with and without the presence of α-amylase. Taken together, this work aims to close data gaps regarding mechanistical effects of MNP on cells by investigating direct MNP-protein-interactions. Mechanistic knowledge is crucial for understanding toxicological effects of MNP, and therefore, also for the risk assessment of possible hazards on human health. T2 - 92. Jahrestagung der Deutschen Gesellschaft für Experimentelle und Klinische Pharmakologie und Toxikologie (DGPT) CY - Düsseldorf, Germany DA - 17.03.2026 KW - Microplastics KW - Nanoplastics PY - 2026 AN - OPUS4-65667 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - CONF A1 - Wöhlecke, Andreas T1 - Aktuelles aus dem BAM-Fachbeirat N2 - Die Anforderungen an Geokunststoffprodukte und deren Qualitätssicherung unterliegen einem stetigen Wandel, der sowohl durch technische Veränderungen als auch durch normative und organisatorische Entwicklungen geprägt ist. Insbesondere der Fachbeirat der BAM gemäß Deponieverordnung (DepV) spielt hier im Bereich der Deponietechnik eine wichtige Rolle. An dieser Stelle sollen aktuelle Themen aus dem Fachbeirat der BAM vorgestellt werden, die wesentliche Änderungen in der Zulassungs- und Anwendungspraxis betreffen. Der Beitrag beleuchtet unter anderem Veränderungen innerhalb der BAM, die Modernisierung der Publikationsformate sowie die fachliche Weiterentwicklung der Zulassungsrichtlinien. T2 - 22. Leipziger Deponiefachtagung CY - Leipzig, Germany DA - 10.03.2026 KW - Deponie KW - Geotextil KW - Abdichtungssystem PY - 2026 AN - OPUS4-65665 LA - deu AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Diehn, S. A1 - Zimmermann, B. A1 - Tafintseva, V. A1 - Seifert, S. A1 - Bagcioglu, M. A1 - Ohlson, M. A1 - Weidner, Steffen A1 - Fjellheim, S. A1 - Kohler, A. A1 - Kneipp, Janina T1 - Combining Chemical Information From Grass Pollen in Multimodal Characterization N2 - The analysis of pollen chemical composition is important to many fields, including agriculture, plant physiology, ecology, allergology, and climate studies. Here, the potential of a combination of different spectroscopic and spectrometric methods regarding the characterization of small biochemical differences between pollen samples was evaluated using multivariate statistical approaches. Pollen samples, collected from three populations of the grass Poa alpina, were analyzed using Fourier-transform infrared (FTIR) spectroscopy, Raman spectroscopy, surface enhanced Raman scattering (SERS), and matrix assisted laser desorption/ionization mass spectrometry (MALDI-TOF MS). The variation in the sample set can be described in a hierarchical framework comprising three populations of the same grass species and four different growth conditions of the parent plants for each of the populations. Therefore, the data set can work here as a model system to evaluate the classification and characterization ability of the different spectroscopic and spectrometric methods. ANOVA Simultaneous Component Analysis (ASCA) was applied to achieve a separation of different sources of variance in the complex sample set. Since the chosen methods and sample preparations probe different parts and/or molecular constituents of the pollen grains, complementary information about the chemical composition of the pollen can be obtained. By using consensus principal component analysis (CPCA), data from the different methods are linked together. This enables an investigation of the underlying global information, since complementary chemical data are combined. The molecular information from four spectroscopies was combined with phenotypical information gathered from the parent plants, thereby helping to potentially link pollen chemistry to other biotic and abiotic parameters. KW - Pollen KW - MALDI-TOF MS KW - FTIR KW - Raman KW - Multivariate analyses PY - 2020 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-504822 DO - https://doi.org/10.3389/fpls.2019.01788 VL - 10 SP - 1788 AN - OPUS4-50482 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kricheldorf, H. R. A1 - Weidner, Steffen T1 - Polymerization of L-lactide with SnCl2: A Low Toxic and Eco-friendly Catalyst N2 - Polymerizations of L-lactide catalyzed either by neat SnCl2 or by SnCl2 + difunctional cocatalysts were conducted in bulk at 180, 160 and 140 °C with variation of the Lac/Cat ratio and time. With neat SnCl2 poly(L-lactide) having weight average molecular weights (uncorrected Mw’s) up to 190 000 g mol−1 were obtained mainly consisting of linear chains. Addition of salicylic acid or 1,1-bisphenol yielded a higher fraction of cyclic polylactides but lower molecular weights. Furthermore, SnCl2 was compared with Bu2SnCl2 and various other metal chlorides and the best results were obtained with SnCl2. With ethyl L-lactate as initiator SnCl2-catalyzed ROPs were performed at 120 °C and the lac/initiator ratio was varied. All these experiments were conducted under conditions allowing for comparison with ROPs catalyzed with neat Sn(II)-2-ethyhexanoate. Such a comparison was also performed with ε-caprolactone as monomer. KW - Catalyst KW - Polylactide KW - MALDI-TOF MS KW - Polycondensation PY - 2021 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-520517 DO - https://doi.org/10.1007/s10924-020-02042-w SN - 1566-2543 SP - 1 EP - 13 PB - Springer Nature AN - OPUS4-52051 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Dudziak, Mateusz A1 - Bhatia, Riya A1 - Dey, R. A1 - Falkenhagen, Jana A1 - Ullrich, M. S. A1 - Thomsen, C. A1 - Schartel, Bernhard T1 - Wastewater phosphorus enriched algae as a sustainable flame retardant in polylactide N2 - Revolutionizing our polymer industry for adaption to a sustainable carbon circular economy has become one of today’s most demanding challenges. Exploiting renewable resources to replace fossil-fuel—based plastics with biopolymers such as poly(lactic acid) (PLA) is inevitable while using waste streams as a raw material resource at least is promising. When it comes to using PLA as technical polymer, its high flammability must be addressed by flame retardants compatible with the thermoplastic processing of PLA and its compostability. This study proposes microalgae enriched with phosphorus from wastewater (P-Algae) as an elegant way towards a kind of sustainable organophosphorus flame retardant. The concept is demonstrated by investigating the processing, pyrolysis, flammability, and fire behavior of PLA/P-Algae, while varying the P-Algae content and comparing P-Algae with four alternative bio-fillers (phosphorylated lignin, biochar, thermally treated sewage sludge, and metal phytate) with different P-contents as meaningful benchmarks. KW - PLA KW - Flame Retardancy KW - Phosphorylated Algae KW - Wastewater flame retardants KW - Zink phytate KW - Phosphorylated lignin KW - Thermally treated sludge PY - 2024 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-604150 DO - https://doi.org/10.1016/j.polymdegradstab.2024.110885 SN - 1873-2321 SN - 0141-3910 VL - 227 SP - 1 EP - 11 PB - Elsevier Ltd. AN - OPUS4-60415 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Cherbib, S. A1 - Jlalia, I. A1 - Chabbah, T. A1 - Chatti, S. A1 - Marestin, C. A1 - Mercier, R. A1 - Weidner, Steffen A1 - Casabianca, H. A1 - Jaffrezic-Renault, N. A1 - Abderrazak, H. T1 - Design of New Partially Bio-Based Polyguanamines for the Reversible Adsorption of Phenolic Molecules from Olive Mill Wastes N2 - Olive mill wastewater produces a variety of potent antioxidants, including hydroxytyrosol, oleuropein, and tyrosol, that have been widely used in agriculture, pharmacy, and cosmetics. This study aims to design new poly(guanamine)s phases by polycondensation of modified triazine monomers with both petro-based and biosourced diamines, to act as stationary phases for the uptake of these phenolic molecules. Obtained polymers were characterized by NMR spectroscopy, differential scanning calorimetry (DSC), and thermogravimetric analysis (TGA). The adsorption results showed that the newly synthesized polymers can effectively uptake the less polar phenolic compounds, ferulic acid, and caffeic acid. The isosorbide-based polymer (P6) presented the highest sorption efficiency, due to the hydrophilic properties of isosorbide associated with the proton affinity of the triazine groups. All the phenolic compounds were successfully desorbed from the P6 polymer using a minimal amount of a methanol/acetonitrile mixture. P6 polymer could be used for four successive adsorption processes without loss of efficiency. KW - Olive mill wastewater KW - Triazine KW - Isosorbide KW - Adsorption KW - Phenolic compounds PY - 2024 DO - https://doi.org/10.1007/s42250-024-01081-3 SN - 2522-5758 SP - 1 EP - 11 PB - Springer Science and Business Media LLC AN - OPUS4-61348 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Geburtig, Anja A1 - Wachtendorf, Volker A1 - Falkenhagen, Jana T1 - Combined impact of UV radiation and nitric acid on high‐density polyethylene containers as a laboratory test N2 - In a laboratory test, transparent high‐density polyethylene (HDPE) jerrycans have been exposed to both UV radiation and 55 wt‐% nitric acid solution at (41 ± 2)°C, for up to 20 days. For comparison, UV radiant exposure (21 days) and nitric acid exposure (up to 6 weeks) were performed separately, at nearly equal temperatures. The damages are compared with FTIR spectroscopy in ATR and HT‐gel permeation chromatography(GPC) on a molecular level and with hydraulic internal pressure testing as a component test. For the used jerrycans, relevant oxidation can only be found after the combined exposure. This is caused by the decomposition of nitric acid into nitrous gases by UV radiation, which is also observed at lower concentrations (28 wt‐%). After 6 days of laboratory exposure, this is rated as critical, which corresponds to about 1/10 year in Central Europe, according to the UV radiant exposure. The gradual increase in oxidative damage shows the reproducibility of the test. KW - Molecular mass distribution KW - High-density polyethylene KW - Nitric acid KW - UV radiation PY - 2022 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-550141 DO - https://doi.org/10.1002/pts.2673 SN - 0894-3214 VL - 35 IS - 10 SP - 729 EP - 735 PB - Wiley CY - New York, NY AN - OPUS4-55014 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Kricheldorf, Hans. R. A1 - Weidner, Steffen T1 - About the Toxicity of Polymerization Catalysts and Polymer Additives Based on Tin(II) Salts and Tin(IV) Compounds N2 - This article reviews and discusses information on the toxicity of numerous tin-based catalysts used in academic research and industrial production for the synthesis of various polymers, such as polyesters, polyurethanes, and polysiloxanes. Tin(IV) compounds used as additives and as PVC stabilizers are also considered. Emphasis is put on the differentiation between tin(II) salts on the one hand and tin(IV) compounds on the other hand. In the first chapter, historical facts about human contact with stannous ions are discussed, along with toxicity studies of canned foods and beverages. In the second part, toxicity tests based on cell cultures and medical applications of tin(II)-containing films or implants are described. The third part focuses on alkyl and aryl tin(IV) compounds. KW - Tin KW - Toxicity KW - Environment KW - Polymer catalysts KW - Polymer additives PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-642877 DO - https://doi.org/10.1021/acs.chas.5c00105 SN - 1871-5532 SP - 1 EP - 13 PB - American Chemical Society (ACS) AN - OPUS4-64287 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER - TY - JOUR A1 - Fink, Friedrich A1 - Stawski, Tomasz M. A1 - Emmerling, Franziska A1 - Falkenhagen, Jana T1 - A novel machine-learning approach to unlock technical lignin classification by NIR spectroscopy - bench to handheld N2 - In this research, the utilization of near-infrared (NIR) spectroscopy in conjunction with advanced machine learning methods is investigated for categorizing technical lignins obtained from different biomass sources and industrial procedures. Technical lignins, such as kraft, organosolv and lignosulfonates, have different chemical compositions, which continue to make uniform characterization and application in sustainable sectors extremely difficult. Fast, universally accessible analytics combined with data analysis is still an open question. For the first time three distinct NIR spectrometers—a high-performance benchtop system, a mid-priced compact device, and an economical handheld unit—were utilized to record NIR spectra of 31 unique lignin samples. The spectra underwent pre-processing through standard normal variate (SNV) transformation and Savitzky-Golay derivatives to amplify spectral features and decrease noise. Principal component analysis (PCA) was employed to reduce data complexity and extract crucial characteristics for classification purposes. Subsequently, four machine learning algorithms—Support Vector Machines (SVM), Gaussian Naive Bayes (GNB), Gaussian Process Classification (GPC), and Decision Tree Classification (DTC)—were implemented for the classification of the lignin samples. The DTC model exhibited the highest accuracy among them across different spectrometers. Although the benchtop spectrometer produced the most precise outcomes, the compact NeoSpectra system also displayed potential as a cost-efficient option. Nonetheless, the restricted spectral coverage of the handheld NIRONE spectrometer resulted in reduced classification accuracy. Our discoveries highlight the capability of NIR spectroscopy, combined with robust data analysis techniques, for the swift and non-destructive classification of technical lignins, facilitating their improved utilization in sustainable fields. KW - Technical lignins KW - NIR spectroscopy KW - Classification KW - Machine-learning KW - PCA PY - 2025 UR - https://nbn-resolving.org/urn:nbn:de:kobv:b43-634518 DO - https://doi.org/10.1016/j.chemolab.2025.105467 SN - 0169-7439 VL - 264 SP - 1 EP - 10 PB - Elsevier B.V. CY - Amsterdam AN - OPUS4-63451 LA - eng AD - Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin, Germany ER -